At the moment we rely on the infamous get_ram_size() function to learn
the actual DRAM size in U-Boot proper. This function has two issues:
1) It only works if the DRAM size is a power of two. We start to see
boards which have 3GB of (usable) DRAM, so this does not fit anymore.
2) As U-Boot has no notion of reserved memory so far, it will happily
ride through the DRAM, possibly stepping on secure-only memory. This
could be a region of DRAM reserved for OP-TEE or some other secure
payload, for instance. It will most likely crash in that case.
As the SPL DRAM init routine has very accurate knowledge of the actual
DRAM size, lets propagate this wisdom to U-Boot proper.
We re-purpose a currently reserved word in our SPL header for that.
The SPL itself stores the detected DRAM size there, and bumps the SPL
header version number in that case. U-Boot proper checks for a valid
SPL header and a high enough version number, then uses the DRAM size
from there. If the SPL header field is not sufficient, we fall back to
the old DRAM scanning routine.
Part of the DRAM might be present and probed by SPL, but not accessible
by the CPU. They're restricted in the main U-Boot binary, when accessing
the DRAM size from SPL header.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Allwinner 64-bit SoCs can use 4GiB DRAM chip, however their memory map
has only allocated 3GiB for DRAM, so only 3GiB of the DRAM is
accessible.
Add a Kconfig option for the maximum accessible DRAM.
For A80 it should be a much higher value (8GiB), but as I have no A80
device to test and originally U-Boot only supports 2GiB DRAM on A80, it
currently still falls under the 2GiB situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
All Allwinner 64-bit SoCs now are known to be able to access 3GiB of
external DRAM, however the size of DRAM part in the MMU translation
table is still 2GiB.
Change the size of DRAM part in MMU table to 3GiB.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
So far we have two users which want to look at the SPL header. We will
get more in the future.
Refactor the existing SPL header checks into a common function, to
simplify reusing the code.
Now that this is easy, add proper version checks to the DT name parsing.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
On Allwinner SoCs we use some free bytes at the beginning of the SPL image
to store various information. We have a version byte to allow updates,
but changing this always requires all tools to be updated as well.
Introduce the concept of semantic versioning [1] to the SPL header:
The major part of the version number only changes on incompatible
updates, a minor number bump indicates backward compatibility.
This patch just documents the major/minor split, adds some comments
to the header file and uses the versioning information for the existing
users.
[1] https://semver.org
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The Pine A64 Plus/non-Plus model detection code is now built on all
64-bit ARM SoCs, even if the code cannot be triggered when H5/H6 is in
use.
Disable them when the board is Pine A64 by adding a Kconfig option that
is only selected on Pine A64.
On GCC 7.3.1 this makes the size of the function reduces 184 bytes, and
saves a 104 byte strstr() function, then makes SPL on H6 succeed to
build.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Since commit 80df194f01 ("x86: detect unsupported relocation types"),
an error message is seen on QEMU x86 target during boot:
do_elf_reloc_fixups32: unsupported relocation type 0x1 at fff841f0, offset = 0xfff00087
do_elf_reloc_fixups32: unsupported relocation type 0x2 at fff841f8, offset = 0xfff00091
Check offset 0xfff00087 and 0xfff00091 in the u-boot ELF image,
fff00087 000df401 R_386_32 00000000 car_uninit
fff00091 000df402 R_386_PC32 00000000 car_uninit
we see R_386_32 and R_386_PC32 relocation type is generated for
symbol car_uninit, which is declared as a weak symbol in start.S.
However the actual weak symbol implementation ends up nowhere. As
we can see below, it's *UND*.
$ objdump -t u-boot | grep car_uninit
00000000 w *UND* 00000000 car_uninit
With this fix, it is normal now.
$ objdump -t u-boot | grep car_uninit
fff00094 w F .text.start 00000001 car_uninit
Reported-by: Hannes Schmelzer <hannes@schmelzer.or.at>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The build breaks because its not fitting the U-Boot binary into the ROM
image. So lets move VGA BIOS a bit to make room for the grown U-Boot
binary.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To enable the root device selection (kernel cmd-line) via PARTUUID, this
patch enables CMD_PART on all missing theadorable-x86 boards and
changes the default environment to generate the root=PARTUUID string
automatically.
This fixes problems that have been noticed on systems with multiple
SATA/AHCI controller connected via PCIe, where the device name for the
root device / partition (/dev/sdaX) was incorrect.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is needed for the PCIe hotplug to work correctly on some boards
with the newer Linux kernel versions.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
To allow bigger 64 bit prefetchable PCI regions in Linux, this patch
changes the base address and range of the ACPI area passed to Linux.
BayTrail can only physically access 36 bit of PCI address space. So
just chaning the range without changing the base address won't work
here, as 0xf.ffff.ffff is already the maximum address.
With this patch, a maximum of 16 GiB of local DDR is supported. This
should be enough for all BayTrail boards though.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Introduce a new script to check whether file exists and
use that check in Makefile to avoid break CI system.
The script return 1 when the required files not exists, return 0
when files exists. The script will ignore check to u-boot-dtb.bin,
because if there is something wrong to generate u-boot-dtb.bin,
there must be some code error.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
However the current code:
- clamps values greater than 1000ms to 1000ms rather than 1.
- does not initialize the delay if the property does not exist
(else clause mismatch)
- returns an error if phy-reset-gpios is not defined
Fix all this and simplify by using dev_read_u32_default()
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware. This allows the same image
to be used on boards that have firmware storage and those that do not.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In upcoming freescale board LX2160AQDS, the MDIO bus is muxed.
i.e. same MDIO bus can be routed to eight different slots depending
on mux register settings.
To support this mdio mux behavior, we add each MDIO bus mux as a
separate MDIO bus.
Now, various phy devices can be attached to each of these slots(mux).
The information about these devices is passed to OS via device tree.
To do the fdt fixups related to MDIO bus, its necessary that MDIO bus
list is accessed.Therefore, add a function to retrieve the list head.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All mii operations require a valid PHY address except the 'device'
command, which expects the PHY name rather than the address.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Choose best prescaler to improve PWM resolution. Without this change
driver chooses first prescaler that gives us period value within
range, but it could be not the best one.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Fix off-by-one that prevented PWM driver to use prescaler bypass.
Without this change prescaler is always enabled.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add an entry for the warp7_bl33_defconfig target.
This fixes the following warnings:
WARNING: no status info for 'warp7_bl33'
WARNING: no maintainers for 'warp7_bl33'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
- Split the AArch64 LS10xx and LS20xx builds into their own jobs, and
then exclude only ls1/ls2 from the catch-all. This moves the S32V234
job (and future i.MX8*) to the catch-all.
- Split spear out from arm926ejs and exclude freescale, not mx from that
job. The older Freescale i.MX boards are caught by the catch-all job
for Freescale but now we build the non-Freescale older i.MX platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Odroid HC2 board is based on Odroid XU4 board, like the Odroid HC1.
The linux kernel does not provide a hc2 DTB so the hc1 DTB is also used
for the Odroid HC2.
Resend because MUA changed whitespace.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Unfortunately the test was not included in the original implementation.
Add one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove "environment" partition and do not read it when booting Android
from eMMC. We don't use this partition anymore, so this is just an
unintentional leftover.
Earlier we were reading dtb file from "environment" partition to feed it
further to kernel. Now we are using dtb from FIT image ("boot" partition
contains boot_fit.img image), which can be seen from this command:
bootm ${loadaddr}#${fdtfile}
where "#" character means we have FIT image in ${loadaddr} RAM address.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Praneeth Bajjuri <praneeth@ti.com>
This is required for the current Linux kernel to reboot. It should also
probably be fixed in Linux.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM37 and OMAP35 SOM-LV SOM-LV products both support a NOR
flash part connected to CS2 in addition to the NAND part on CS0.
This patch setups the GPMC timings for the MT28 NOR Flash and
enables the CFI-Flash driver now that the CFI stuff is in Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Dirk Meul <dirk.meul@rwth-aachen.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Compiling the overlay unit test fails with odroid-c2_defconfig showing
errors like:
test/overlay/cmd_ut_overlay.c:29:8:
error: unknown type name ‘fdt32_t’
Add the missing include.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently in pmecc_get_sigma(), the code tries to clear the memory
pointed by smu with wrong size 'sizeof(int16_t) * ARRAY_SIZE(smu)'.
Since smu is actually a pointer, not an array, so ARRAY_SIZE(smu)
does not generate correct size to be cleared.
In fact, GCC 8.1.0 reports a warning against it:
error: division 'sizeof (int16_t * {aka short int *}) / sizeof (int16_t
{aka short int})' does not compute the number of array elements
[-Werror=sizeof-pointer-div]
Fix it by using the correct size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
When booting and CPU is detected from cpuid, we also need an environment
variable that will be used in boot commands to load the proper devicetree.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In my haste to migrate SPL to DM, I copied the wrong name.
While it really doesn't matter, I'd prefer the name to match
the board, so am335x_mmc0 is now called omap3_logic_mmc0
Signed-off-by: Adam Ford <aford173@gmail.com>
With the new omap_serial driver, this patch uses this instead
from the former ns16550_serial driver. Even though the
omap_serial driver is essentially the same.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the DM_USB working for USB host features, encapsulate the
USB gadget initialization in a precomiler check. If DM is enabled,
we don't need to manually initialize the MUSB driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
The default timings are assumming an OMAP36 / AM37 / DM37, but
the OMAP35 controller is a bit slower, so DDR may operate out of
spec when under stress. This patch checks the processor type and
sets the DDR timings according to processor type.
Fixes: 5ad4212ce0 ("ARM: DTS: Add Logic PD OMAP35/DM37 SOM-LV
and OMAP35 Torpedo")
Signed-off-by: Adam Ford <aford173@gmail.com>
The da850evm does not need this enabled, so this removes a
notice that appears during compile time that says
"Please remove"
Signed-off-by: Adam Ford <aford173@gmail.com>
If we have defined the OPTEE ram size and not OPTEE means that we are in
the case where OPTEE is loaded already (maybe by ARM Trusted Firmware) and
that most of the low level initialization is already done and that we
may/should skip it doing them here.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: u-boot@lists.denx.de
We may have, the not yet considered, scenario where OPTEE is loaded before
u-boot and *not* by u-boot, e.g, the boot flow using the ARM Trusted
Firmware (ATF), where in the 32bit flow is:
BootRom->ATF(BL2)->Optee(BL32)->u-boot(BL33)
In this case we need still to reserve the memory used by optee, to avoid
for example to realocate ourself to the same address at the end of DRAM.
So, we change here the dependencies on the OPTEE lib and we set the default
size and base of TZRAM to zero.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Cc: u-boot@lists.denx.de
We can have the case where u-boot is launched after some other low level
enabler, like for example when u-boot runs after arm-trusted-firmware
and/or optee. So, because of that we may need to jump the initialization of
some IP blocks even because we may no longer have the permission for that.
So, if the config option to skip low level init is set disable also timer,
board and csu initialization.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: u-boot@lists.denx.de
Reviewed-by: Peng Fan <peng.fan@nxp.com>
I2C bus 0 was not initialized correctly. There is an offset between i2c
index and the structure number of pad info. So i2c bus 0 can be in an
inconsistent state.
This problem become visible on B{4,6}50v3 with the CPUC HW watchdog enabled.
Sometimes when the CPUC HW watchdog interrupted the boot process, U-Boot was
not able to read VPD from I2C/EEPROM and the system failed to boot up again,
because a device connected to that bus was stuck in data transfer state (from
previous boot attempt) and there was no method to recover (struct
mxc_i2c_bus::idle_bus_fn was not set) courtesy of incorrect initialization.
Signed-off-by: Dan Cimpoca <dan.I.cimpoca@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
The b{4,6}50v3 kernel framebuffer console requires a modeline otherwise
the LVDS panel shows garbage.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
While using ./scripts/get_maintainer.pl I detect that the Maintainer name
and address for bx50v3 boards are not valid.
The new maintainer for GE bx50v3 products must be Ian Ray.
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
There is no need to have README in all i.MX documents name.
Remove README from i.MX docs name and add .txt file extension.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
The Serial Download Protocol feature is availible in various
i.MX SoCs.
Move README.sdp document to imx/misc directory.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The current High Assurance Boot document README.mxc_hab
include details for the following features in a single file:
- HAB Secure Boot
- HAB Encrypted Boot
Split HAB documentation in a specific directory for a cleaner
documentation structure, subsequent patches will include more
content in HAB documentation.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The following documents describe device details according to the
i.MX family:
- README.imx25
- README.imx27
- README.imx5
- README.imx6
- README.mxs
Move all device common related document to doc/imx/common for a better
directory structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The following documents describe the image type used by the mkimage
tool to generate U-Boot images for i.MX devices.
- README.imximage
- README.mxsimage
Move all mkimage related document to doc/imx/mkimage for a better
directory structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the Serial Download Protocol tools and procedure are
documented in two places:
- doc/imx/README.sdp
- doc/imx/README.imx6
It is better to consolidate all SDP related information into
README.sdp file, so move the content from README.imx6 to
README.sdp.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the U-Boot doc/ directory contains the following files
that are only relevant for i.MX devices:
- doc/README.imx25
- doc/README.imx27
- doc/README.imx5
- doc/README.imx6
- doc/README.imximage
- doc/README.mxc_hab
- doc/README.mxs
- doc/README.mxsimage
- doc/README.sdp
Move all content to a common i.MX folder for a better documentation
structure.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
When building i.MX8/8X board, use imx8image type.
`-e $(CONFIG_SYS_TEXT_BASE)` is not needed, but
no harm to keep it for i.MX8/8X
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8/8X bootable image type is container type.
The bootable image, containers a container set which supports two
container. The 1st container is for SECO firmware, the 2nd container
needs to include scfw, m4_0/1 image, ACore images per your requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Introduce dtsi for i.MX8QXP, since there is other variants i.MX8DX(P),
so add them there, because i.MX8QXP includes the dtsi of them.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Modify most APIs to use udevice as the first parameter, then
it will be easy to get the clk reference by using udevice pointer.
Use uclass api to get lpuart clk when CONFIG_CLK is enabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Enable the RX and TX FIFO in LPUART driver to avoid the input lost
during U-Boot boot up.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8 compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also, according to RM, the Receive FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08
(not 0x40) for i.MX8, otherwise the Receive FIFO is not disabled.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add the power domain DM driver for i.MX8, that it depends on the DTB
power domain trees to generate the power domain provider devices. Users
need to add power domain trees with property "compatible = "nxp,imx8-pd";"
When power on a PD device, the driver will power on its ancestor PD
devices in power domain tree.
When power off a PD device, the driver will check its child PD devices
first. Only if all child PD devices are off, then power off the current PD
device. Then the driver checks sibling PD devices. If sibling PD devices
are off, then it will power off parent PD device.
There is no counter maintained in this driver, but a state to hold current
on/off state. So the request and free functions are empty.
The power domain implementation in i.MX8 DTB set the "#power-domain-cells"
to 0, so there is no ID binding with each PD device. We don't use "id"
variable in struct power_domain. At the same time, we have to set of_xlate
to empty to bypass standard of_xlate in uclass driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add pinctrl driver for i.MX8. The pads configuration is controlled
by SCU, so need to ask SCU to configure pads through scfw API.
Add pinctrl-scu to invoke sc_pad_set to configure pads.
Add a new flag IMX8_USE_SCU to differentiate i.MX8 from other platforms
which could directly configure pads from Acore side.
Add CONFIG_PINCTRL_IMX8 as the built gate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This driver is mostly used to avoid build errors.
We use uclass clk driver for clk related operations.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
print_cpuinfo() in board init code requires uclass CPU driver,
add it to be able to display CPU info when CONFIG_DISPLAY_CPUINFO
option is enabled. CPU node in DT will have to include 'clocks'
and 'u-boot,dm-pre-reloc' properties for generic print_cpuinfo()
to work as expected. The driver outputs info for i.MX8QXP Rev A
and Rev B CPUs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add arch_cpu_init(_dm) mainly to open the channel between ACore and SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add mmu memmap, some memory regions are reserved by M4, Arm Trusted
Firmware, so need to get memreg using SCFW API and setup the memmap.
Add dram_init, dram_init_banksize, get_effective_memsize functions,
according to the memreg.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add basic cpu support, including cpu revision, cpu type,
cpu core detection.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add imx-regs header file to include the register base definition
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add clk/misc/pad/pm/rm scfw api implementaion for different
drivers to invoke. The low level code is using misc_call
to invoke imx8_scu driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add i.MX8 MISC driver to handle the communication between
A35 Core and SCU.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add scu_dev for i.MX8, this will be used as a handle
to communite with SCU from A35.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add qemu-x86_64 to the list of targets we use for test.py runs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Specify X86_TSC_TIMER_EARLY_FREQ for Quark SoC so that TSC as
the early timer can be supported.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far the TSC timer driver supports trying hardware calibration first
and using device tree as last resort for its running frequency as the
normal timer.
However when it is used as the early timer, it only supports hardware
calibration and if it fails, the driver just panics. This introduces
a new config option to specify the early timer frequency in MHz and
it should be equal to the value described in the device tree.
Without this patch, the travis-ci testing on QEMU x86_64 target fails
each time after it finishes the 'bootefi selftest' as the test.py see
an error was emitted on the console like this:
TSC frequency is ZERO
resetting ...
### ERROR ### Please RESET the board ###
It's strange that this error is consistently seen on the travis-ci
machine, but only occasionally seen on my local machine (maybe 1 out
of 10). Since QEMU x86_64 target enables BOOTSTAGE support which uses
early timer, with this fix it should work without any failure.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present in arch_setup_gd() it calls printch(' ') at the end which
has been a mystery for a long time as without such call the 64-bit
U-Boot just does not boot at all.
In fact this is due to the bug that board_init_f() was called with
boot_flags not being set. Hence whatever value being there in the
rdi register becomes the boot_flags if without such magic call.
With a printch(' ') call the rdi register is initialized as 0x20
and this value seems to be sane enough for the whole boot process.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On x86_64 the field global_data_ptr is assigned before relocation. As
sections for uninitialized global data (.bss) overlap with the relocation
sections (.rela) this destroys the relocation table and leads to spurious
errors.
Initialization forces the global_data_ptr into a section for initialized
global data (.data) which cannot overlap any .rela section.
Fixes: a160092a61 ("x86: Support global_data on x86_64")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently we support only relocations of type ELF64_R_TYPE or ELF32_R_TYPE.
We should be warned if other relocation types appear in the relocation
sections.
This type of message has helped to identify code overwriting a relocation
section before relocation and incorrect parsing of relocation tables.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Since commit 380d4f787a ("rtc: Allow use of RTC in SPL and TPL")
qemu-x86_64_defconfig does not boot anymore.
Fixes: 380d4f787a ("rtc: Allow use of RTC in SPL and TPL")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are some sections in current doc saying 64-bit is unsupported.
This apparently is out of date. Remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently only 32-bit U-Boot for QEMU x86 is documented. Mention
the 64-bit support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the '-march=core2' fix, it seems that we have some luck that
the 64-bit U-Boot boots again. However if we examine the disassembly
codes there are still SSE instructions elsewhere which means passing
cpu type to GCC is not enough to prevent it from generating these
instructions. A simple test case is doing a 'bootefi selftest' from
the U-Boot shell and it leads to a reset too.
The 'bootefi selftest' reset is even seen with the image created by
the relative older GCC 5.4.0, the one shipped by Ubuntu 16.04.
The reset actually originates from undefined instruction exception
caused by these SSE instructions. To keep U-Boot as a bootloader as
simple as possible, we don't want to handle such advanced SIMD stuff.
To make sure no MMX/SSE instruction sets are generated, tell GCC not
to do this. Note AVX is out of the question as CORE2 is old enough
to support AVX yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
With newer kernel.org GCC (7.3.0 or 8.1.0), the u-boot.rom image
built for qemu-x86_64 target does not boot. It keeps resetting
soon after the 32-bit SPL jumps to 64-bit proper. Debugging shows
that the reset happens inside env_callback_init().
000000000113dd85 <env_callback_init>:
113dd85: 41 54 push %r12
113dd87: 55 push %rbp
113dd88: 31 c0 xor %eax,%eax
113dd8a: 53 push %rbx
113dd8b: 0f 57 c0 xorps %xmm0,%xmm0
Executing "xorps %xmm0,%xmm0" causes CPU to immediately reset.
However older GCC like 5.4.0 (the one shipped by Ubuntu 16.04)
does not generate such instructions that utilizes SSE for this
function - env_callback_init() and U-Boot boots without any issue.
Explicitly specifying -march=core2 for newer GCC allows U-Boot
proper to boot again. Examine assembly codes of env_callback_init
and there is no SSE instruction in that function hence U-Boot
continues to boot.
core2 seems to be the oldest arch in GCC that supports 64-bit.
Like 32-bit U-Boot build we use -march=i386 which is the most
conservative cpu type so that the image can run on any x86
processor, let's do the same for the 64-bit U-Boot build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In initr_bootstage() we call bootstage_mark_name() which ends up calling
timer_get_us(). This call happens before initr_dm(), which inits driver
model.
On x86 we set gd->timer to NULL in the transition from board_init_f()
to board_init_r(). See board_init_f_r() for this assignment. So U-Boot
knows there is no timer available in the period immediately after
relocation.
On x86 the timer_get_us() call is implemented as calls to get_ticks() and
get_tbclk(). Both of these call dm_timer_init() to set up the timer, if
gd->timer is NULL and the early timer is not available.
However dm_timer_init() cannot succeed before initr_dm() is called.
So it seems that on x86 if we want to use CONFIG_BOOTSTAGE we must enable
CONFIG_TIMER_EARLY. Update the Kconfig to handle this.
Note: On most architectures we can rely on the pre-relocation memory still
being available, so that gd->timer pointers to a valid timer device and
everything works correctly. Admittedly this is not strictly correct since
the timer device is set up by pre-relocation U-Boot, but normally this is
fine. On x86 the 'CAR' (cache-as-RAM) memory used by pre-relocation U-Boot
disappears in board_init_f_r() and any attempt to access it will hang.
This is the reason why we must mark the timer as invalid when we get to
board_init_f_r().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some platforms use this instead of FSP to set up the platform, including
memory. Add support for this in binman. This is needed for
chromebook_samus, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With bootstage now allocating pre-relocation memory the current amount
available is insufficient. Increase it a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add test which checks if a PCI device described in DT with an
entry and reg = <...> property, but without compatible string
results in a valid U-Boot PCI udevice with the udevice.node
populated with reference to this DT node. Also check if the
other PCI device without a DT node does not contain any bogus
udevice.node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add PCI entry without compatible string and with a DT node only with
reg = <...> property into the DT. This is needed for the tests to
verify whether such a setup creates an U-Boot PCI device with the
DT node associated with it in udevice.node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The PCI controller can have DT subnodes describing extra properties
of particular PCI devices, ie. a PHY attached to an EHCI controller
on a PCI bus. This patch parses those DT subnodes and assigns a node
to the PCI device instance, so that the driver can extract details
from that node and ie. configure the PHY using the PHY subsystem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>
To make testing with clang support easier, add sandbox/clang-7
combination to our testing matrix. To facilitate this, switch to using
the "sources" method that the travis.yml file supports to list
additional repositories and add the official one for llvm-7. Due to
buildman not supporting using clang at this time add logic to manually
build a single sandbox configuration in the expected output directory so
that we can still invoke all of our tests.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add new Kconfig option, SYS_BOOTCOUNT_MAGIC, to select the boot
counter magic word. This can be useful ie. in case the entire
boot counter register is not usable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Currently this uses x86_64 version toolchain for x86 build in
travis-ci. Change it to i386 version to avoid updating the
buildman toolchain path every time when the toolchain version
number is changed, eg: from 7.3.0 to 8.1.0.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This value is unly used in arch/arm/mach-omap2/am33xx/
clock_am33xx.c, so let's make it dependent on AM33XX since
that is the only way this file gets compiled into the code
according to the Makefile.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix symbol name]
Signed-off-by: Tom Rini <trini@konsulko.com>
The option has never existed and config whitelist script accumulates
it from a comment block, wipe it out from the source code.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
To prevent accidental build failures the change converts a number of
NXP LPC32xx specific image targets to be conditionally dependent on
target build configuration. The wrapped image targets always contain
a U-Boot SPL binary and the images are supposed to be directly flashed
on a NAND flash device for read access by LPC32xx NAND MLC controller.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The explicit arch specific build symbol allows to group supported
boards, generalize common config options and it will serve as
a dependency for platform only drivers.
Two related board defconfigs are resynced after the change.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The PRR syscon driver is available too late for Multi DTB build
of U-Boot. Replace it with simple check whether a platform is
Gen3 or not and produce an address of the PRR.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Build the -u-boot variants of the device trees so they can be included
in Multi-DTB fitImage, which in turn allows us to build single U-Boot
image for multiple boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
When referring to the MSTPSR register, it contains the clock
status of SYS, RT, SECURE, and controlling SMSTPCR using this
value has the problem of being affected by the RT and SECURE
status.This patch changes the reference register to SMSTPCR.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
GSX clock force supply code is unnecessary at U-Boot,
because GSX clock control is supported at the kernel driver.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
This code is unnecessary, because these registers are set by the
initial program loader (IPL).
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
This patch removes 'console=' argument, because kernel uses
stdout-path as parameter.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Patch queue for efi - 2018-10-17
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
Remove a superfluous statement in efi_dp_get_next_instance().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When the last protocol interface is uninstalled the handle is deleted but
this does not set the value of the handle to NULL.
To create a new handle with OpenProtocolInterface the value of the handle
must be NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds new zynqmp command "zynqmp tcminit mode" to
initialize TCM. TCM needs to be initialized before accessing
to avoid ECC errors. This new command helps to perform
the same. It also makes tcm_init() as global and uses it for
doing the TCM initialization.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves TCM initialization to a separate routine to
make it modular and can be reused if required. It also prints
warning message now as it writes to TCM.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Virtual QEMU board is generating DTB self and putting it to
VERSAL_QEMU_DTB_ADDR address.
Board is using CONFIG_OF_BOARD which ensures that u-boot is aligned with
board created by QEMU.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As observed with clang:
fs/fat/fat_write.c:1024:13: warning: comparison of constant 128
with expression of type 'char' is always false
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~~~~ ^ ~
fs/fat/fat_write.c:1024:25: warning: comparison of constant 255
with expression of type 'char' is always true
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~ ^ ~~~~
Fixes: 25bb9dab14 ("fs: fat: check and normalize file name")
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
As observed with clang:
lib/efi_loader/efi_boottime.c:1624:7: warning: variable 'info'
is used uninitialized whenever 'if' condition is true [-Wsometimes-uninitialized]
if (ret != EFI_SUCCESS)
^~~~~~~~~~~~~~~~~~
lib/efi_loader/efi_boottime.c:1653:7: note: uninitialized use
occurs here
free(info);
^~~~
lib/efi_loader/efi_boottime.c:1624:3: note: remove the 'if' if
its condition is always false
if (ret != EFI_SUCCESS)
^~~~~~~~~~~~~~~~~~~~~~~
lib/efi_loader/efi_boottime.c:1602:31: note: initialize the
variable 'info' to silence this warning
struct efi_loaded_image *info;
^
= NULL
Rather than change how we unwind the function it makes the most sense to
initialize info to NULL so that we can continue to pass it to free().
Fixes: c982874e93 ("efi_loader: refactor efi_setup_loaded_image()")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should not include the same include twice.
Fixes: 99b8db7291 ("arm: print information about loaded UEFI images")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Do not leak native_name if out of memory.
This addresses CoverityScan CID 184095.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When is_dir() is called we have already execute set_blk_dev(fh).
So don't call it again.
This fixes CoverityScan CID 184093.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use a return type that can encompass the return value.
This fixes CoverityScan CID 184090.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
getc() might return an error code. Avoid an incorrect converison to
Unicode.
This addresses CoverityScan CID 184087.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The first parameter of efi_allocate_pool is a memory type. It cannot be
EFI_ALLOCATE_ANY_PAGES. Use EFI_BOOT_SERVICES_DATA instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If DEBUG is defined we may be calling EFI_CALL already during the
initialization of the EFI subsystem. We must make sure efi_save_gd() has
already been called at that moment.
Anyway it is better to have this call in one location instead of three.
This fixes an illegal memory access occurring since 4e6b5d6503
("efi_loader: create root node") with DEBUG = 1.
Fixes: 4e6b5d6503 ("efi_loader: create root node")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec requires that file positions are passed as u64 in
GetPosition() and SetPosition().
Check if the file handle points to a directory in GetPosition().
Provide a unit test for GetPosition() and SetPosition().
Fix Coverity warning CID 184079 (CONSTANT_EXPRESSION_RESULT).
Add comments.
Fixes: b6dd577737 ("efi_loader: use correct types in EFI_FILE_PROTOCOL")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the relocation of the EFI runtime on x86_64 fails. This renders
the EFI subsystem unusable. The ELF relocation records for x86_64 contain
an addend field.
Always write the function name into error messages related to the EFI
runtime relocation.
Break an excessively long line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Do gic cpu initialization based on EL level which u-boot enters.
U-Boot can't access EL3 regs when runs in EL2/EL1, etc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet is not present on this board that's why there are two other
options how to wire the board to ethernet. The first is asix_eth usb
host converter which is already enabled by default. The second option is
to use USB CDC/RNDIS ethernet gadget.
This patch is enabling CDC which is working with Linux.
With new bind/unbind command there is no need to call usb_ether_init()
from platform code and use for example these commands:
bind /amba/usb0@ff9d0000/dwc3@fe200000 usb_ether
dhcp
unbind /amba/usb0@ff9d0000/dwc3@fe200000
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx DLC20 has I2C0 with EEPROM(1KB), UART1, GPIO, SD0 (EMMC 4GB),
USB0 device, ENET0, QSPI (16MB) and DDR(two of 256MB each).
Boards have mix of Winbond/ST QSPIs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch partially reverts:
"spl: fit: Add support for loading FPGA bitstream"
(sha1: 26a642238b)
There shouldn't be a need to call private spl_load_fpga_image function
because the whole sequence should be already handled by fpga framework.
If there is missing loading bistream by chunks it should be done via
fpga framework instead of having private hooks.
Also spl_load_fpga_image() weak function is not used anywhere and
opening a way for not reviewed hacks out of mainline U-Boot is not the
right way to go.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Menlosystems M53 board, based on the M53 SoM.
This board has Ethernet, USB host, USB gadget, UART and LCD on it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Add code to configure PLL4, from which the LDB clock are directly
derived.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The board_video_skip() implementation in imx-common/video.c works
on i.MX5x as well, so loosen the SoC filter in Makefile to make it
available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
More fixes and improvements for ARC here:
Fixes (this time included for real):
* Take care of global uninitialized variables
They used to be put right after .bss section and were never
zeroed as they should be. Now merged with normal .bss
Improvements:
* Print more verbose CPU info for boards built on real silicon
* Add support for SD-card detection on all ARC boards
* Quite a few fixes for IoT DK
- Support reset by command
- Print of CPU freq on boot
- Link for eFlash etc
By default GCC puts global non-initialized variables in COMMON section.
And we used to ignore existence of COMMON section in our linker
scripts though smart LD silently appended it right after .bss.
And the problem here is variables from COMMON section even though
require zeroing in run-time were not zeroed as they were placed
right after __bss_end symbol.
It was a pure luck we never faced serious problem due to this,
but now it is fixed.
Now as for some other architectures we'll just force GCC to put
those global variables in normal .bss section.
This solution is much nicer than adding COMMON section to each and
every linker script.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
That's what we'll have in production.
But note it won't work for loading via JTAG as
eFlash is not directly writable, one needs to use
prebootloader to flash uboot.bin from SD-card into eFlash.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
So now we may detect MMC/SD-card existence and
instead of completely misleading message on missing card:
------------------------>8-----------------------
Loading Environment from FAT... Card did not respond to voltage select!
------------------------>8-----------------------
we now get very clear one:
------------------------>8-----------------------
Loading Environment from FAT... MMC: no card present
------------------------>8-----------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Since gd->cpu_clk is a global item we may once populate it from .dtb
ans use it then in other places like for printing CPU info etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARC IDENTITY register only encodes major architecture
type and version while for a particular board/silicon we
may know better which template was used and so we may identify
CPU more precise, which exactly we do here.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This allows board to override print_cpuinfo() because
they might know better which ARChitect template was used.
This way we may not only derive base architecture type and
version but more meaningful things like "ARC EM7D" instead of
simple "ARC EM", "ARC HS36" instead of "ARC HS".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There's no Ethernet controller on the board so no point in having
networking support. This also saves us 5.5 kB of precious memory.
| # bloat-o-meter u-boot.net u-boot.no_net_regex | tail -1
| Total: Before=127892, After=122334, chg -4.35%
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We need to #ifdef some variables to avoid warning about them being
unused.
Fixes: 1a048cd656 ("driver: net: fsl-mc: Add support of multiple phys for dpmac")
Signed-off-by: Tom Rini <trini@konsulko.com>
NOR flash name MT35X_QLKA and MT25Q_** used on NXP board has
manufacturer id as 0x2C, which are rather for newer flashes
after the split of Micron from ST.
So macro for this micron manufacturer id.
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[jagan: updated commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Till now we have had cases where we had one phy device per dpmac.
Now, with the upcoming products (LX2160AQDS), we have cases, where there
are sometimes two phy devices for one dpmac. One phy for TX lanes and
one phy for RX lanes. to handle such cases, add the support for multiple
phys in ethernet driver. The ethernet link is up if all the phy devices
connected to one dpmac report link up. also the link capabilities are
limited by the weakest phy device.
i.e. say if there are two phys for one dpmac. one operates at 10G without
autoneg and other operate at 1G with autoneg. Then the ethernet interface
will operate at 1G without autoneg.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The dpmac initalization should not depend on phy.
As the phy is not necessary to be present for dpmac to function.
Therefore, remove dpmac initialization dependency from phy.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
when there is no phy present for a dpmac, a dummy phy device is created.
when we move to multiple phy method, we need to create as many dummy phy
devices.
Change this method so that we don't need to create dummy phy devices.
We always report linkup if no phy is present.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs during init_phy, we should free the phydev structure
which has been allocated by phy_connect.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phydev structure is present in both ldpaa_eth_priv and
wriop_dpmac_info. the phydev in wriop_dpmac_info is not being used
As the phydev is created based on phy_addr and bus members of
wriop_dpmac_info, it is appropriate to keep phydev in wriop_dpmac_info.
Also phy_regs is not being used, therefore remove it
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add board-specific hook which is executed before the code hands over
control to the OS. This lets the board perform some last-minute clean
ups.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Read the boot mode register to find the boot mode. Only use eMMC boot0
mode when the mode is eMMC boot (called BOOT_DEVICE_MMC1 currently due
to current conflating of boot mode and boot device), and not iff the
boot device is MMC port 0.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
For most devices the boot mode maps directly to the boot
device. For MMC this is not the case as we have two MMC
boot modes and two MMC boot devices (ports). Check the
boot port to determine which MMC device was our boot
device. Make this change for both primary and secondary
boot modes.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Push generic defines of gpio.h out of mach-davinci to drivers/gpio
now that non-davinci architectures are beginning to use this IP.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix calimain build]
Signed-off-by: Tom Rini <trini@konsulko.com>
The uinitrd fixup logic should be executed after the FDT /chosen
node has been properly populated by fdt_initrd()
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When updating the board FDT, some of the operations
are performed by ft_board_setup_ex() and should be
executed also by the fdt command.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.
This initial submission supports UART, MMC/SDCard and Ethernet.
USB is partially supported.
All the code is from Neil Armstrong! I just rebased the code, do
some cleanup and tested on my board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
This adds Device Tree for the Khadas VIM2 board.
The meson-gxm-khadas-vim2.dts is synchronized from Linux 4.18.10.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Make it possible to add TCP versions of the same, while reusing
IP portions. This patch should not change any behavior.
Signed-off-by: Duncan Hare <DH@Synoia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Peter originally sent a fix, but it breaks a number of other things.
This addresses the original reported issue in a different way.
That report was:
> U-Boot has 1 common buffer to send Ethernet frames, pointed to by
> net_tx_packet. When sending to an IP address without knowing the MAC
> address, U-Boot makes an ARP request (using the arp_tx_packet buffer)
> to find out the MAC address of the IP addressr. When a matching ARP
> reply is received, U-Boot continues sending the frame stored in the
> net_tx_packet buffer.
>
> However, in the mean time, if U-Boot needs to send out any network
> packets (e.g. replying ping packets or ARP requests for its own IP
> address etc.), it will use the net_tx_packet buffer to prepare the
> new packet. Thus this buffer is no longer the original packet meant
> to be transmitted after the ARP reply. The original packet will be
> lost.
This instead uses the ARP tx buffer to send async replies in the case
where we are actively waiting for an ARP reply.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Tran Tien Dat <peter.trantiendat@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The target will respond to pings while doing other network handling.
Make sure that the response happens and is correct.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This tests that ARP requests made to this target's IP address are
responded-to by the target when it is doing other networking operations.
This currently corrupts the ongoing operation of the device if it
happens to be awaiting an ARP reply of its own to whatever serverip it
is attempting to communicate with. In the test, add an expectation that
the user operation (ping, in this case) will fail. A later patch will
address this problem.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tests need to be able to pass their "unit test state" to the handlers
where asserts are evaluated. Add a function that allows the tests to set
this private data on the sandbox eth device.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use up to the max allocated receive buffers so as to be able to test
more complex situations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If tests want to implement tx handlers, they will likely need access to
the details in the priv structure.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
NXP SoCs like LX2160A can support new ethernet modes
which are 25G_AUI(25G), XLAUI(40G), CAUI2(50G)
and CAUI4(100G)
Add corresponding macros definitions in phy_interface.h
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DP83867 has a muxing option for the CLK_OUT pin. It is possible
to set CLK_OUT for different channels.
Create a binding to select a specific clock for CLK_OUT pin.
Based on commit 9708fb630d19 ("net: phy: dp83867: Add binding for
the CLK_OUT pin muxing option") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DP83867 when not properly bootstrapped - especially with LED_0 pin -
can enter N/A MODE4 for "port mirroring" feature.
To provide normal operation of the PHY, one needs not only to explicitly
disable the port mirroring feature, but as well stop some IC internal
testing (which disables RGMII communication).
To do that the STRAP_STS1 (0x006E) register must be read and RESERVED bit
11 examined. When it is set, the another RESERVED bit (11) at PHYCR
(0x0010) register must be clear to disable testing mode and enable RGMII
communication.
Thorough explanation of the problem can be found at following e2e thread:
"DP83867IR: Problem with RESERVED bits in PHY Control Register (PHYCR) -
Linux driver"
https://e2e.ti.com/support/interface/ethernet/f/903/p/571313/2096954#2096954
Based on commit ac6e058b75be ("net: phy: dp83867: Recover from "port mirroring"
N/A MODE4") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
This patch adds support for enabling or disabling the lane swapping
(called "port mirroring" in PHY's CFG4 register) feature of the DP83867
TI's PHY device.
One use case is when bootstrap configuration enables this feature (because
of e.g. LED_0 wrong wiring) so then one needs to disable it in software
(at u-boot/Linux).
Based on commit fc6d39c39581 ("net: phy: dp83867: Add lane swapping
support in the DP83867 TI's PHY driver") of mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are VLAN related macros defined in include/linux/if_vlan.h
in Linux kernel, as well as some kernel useful structures and inline
functions. Instead of a complete import from kernel, let's add these
VLAN macros to U-Boot's include/linux/if_ether.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are plenty of existing drivers that have macros like ETH_ALEN
defined in their own source files. Now that we imported the kernel's
if_ether.h to U-Boot we can reduce some duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This imports include/uapi/linux/if_ether.h from Linux kernel v4.17.
It can be very helpful When porting Linux ethernet driver to U-Boot.
Note it is not exactly the same as the kernel one, as checkpatch
issues are fixed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Currently the DRAM bus gate and reset is changed at the same time in
H6 DRAM initialization code, which disobeys the user manual's
programming guide.
Fix the sequence by follow the sequence suggested by the user manual
(ungate the bus clock after release the reset signal).
By some experiments it seems to fix the DRAM size detection failure that
rarely happens.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Davanci spi driver has DM support already, this patch
add support for platdata so-that SPL can use it for
low foot-print.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Adam Ford <aford173@gmail.com>
Some boards (like omap3_logic) hang when trying to access
address 0. This happens when executing the new 'mtd list' command.
This patch enhances the checks for conditions that would
preclude mtd_probe_devices() from operating.
Fixes: 5db66b3aee ("cmd: mtd: add 'mtd' command")
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently there are two ethernet drivers (mvneta.c and mvpp2.c) that
has netdev_### (eg: netdev_dbg) log macros defined in its own driver
file. This adds these log macros in a common place linux/compat.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This syncs U-Boot's include/linux/mdio.h with Linux kernel v4.17
include/uapi/linux/mdio.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This syncs U-Boot's include/linux/mii.h with Linux kernel v4.17
include/uapi/linux/mii.h.
While we are here, this also fixes some style issues.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot,
dm-spl") removes the u-boot,dm-spl properties from the imx6ul.dtsi file
and breaks the OPOS6UL board.
Add the u-boot,dm-spl properties into *-u-boot.dts files to make the
board boot again.
Fixes: commit 9faa43c4b5 ("ARM: dts: i.MX6UL: U-Boot specific dts for u-boot, dm-spl")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rather than passing a hardcoded maxsize to the generic get_ram_size()
function use the i.MX 7 specific imx_ddr_size() function, which extracts
the memory size at runtime by reading the DDR controller registers.
This is a purely cosmetic change as the generic get_ram_size() function
already took care of properly automatically detecting 256MB, 512MB or 1GB
modules.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
The imx_ddr_size() function may overflow as it is possible to kind of
over provision the DDR controller. Fix this by capping it to 2 GB which
is the maximum allowed size as per reference manual.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
USB OTG2 port is connected to the USB host connector.
Add support for it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently SPL binary is larger than 64kB, which is larger than
CONFIG_SPL_MAX_SIZE defined in imx7_spl.h.
This causes boot failure on the pico-mx7 targets.
Remove CONFIG_SPL_LIBDISK_SUPPORT option for now, so that the SPL
binary can fit into the 64kB range.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the use of a USB storage or PXE network booting as
fallback, allowing for example for manufacturing installation of eMMC
storage in an easy way.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
After discussing with TechNexion about how its default setting, it is
better to install on the eMMC user partition by default, when using
DFU, so it works out of box for majority of users.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The CPLD is used to reset the ULCB and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add a little more information to one comment and update the guard comment
to be more accurate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present this function uses pixels but it seems more useful for it to
position in terms of characters on the screen. This also matches the
comment to the function. Update this.
Unfortunately there is one user of this function (at91). Have a crack at
fixing this, since I cannot test it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
We have a method to return the last reset as a string for humans, but not
a method that allows it to be used programmatically. Add a new method that
returns the last reset as an enum.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present // in a device-tree file or link script causes a warning. But
this is used in the standard license header. Update the compiler flags to
use C99, which permits this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ctags emits lines with unmatched quotes which means that the
output file is invalid. This is with exuberant-ctags version 5.9~svn201103
but I also see it with plain ctags. I am not sure that it is a bug though.
Make a few minor changes in the source code to fix this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the panel can be turned on but not off, and the brightness
cannot be controlled at run-time. Add a new API function to both the panel
and backlight uclasses to handle this. Enhance the PWM backlight driver
to deal with custom levels properly and allow the backlight to be turned
on and off.
Update the test to cover thes new features.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this uclass has no tests. Add a simple one which checks the PWM
configuration, regulator and GPIO.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present version 3 messages are only supported on SPI. Add support for
using LPC as well, as used on samus.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the mtrr functions disable the cache before making changes and
enable it again afterwards. This is fine in U-Boot, but does not work if
running in CAR (such as we are in SPL).
Update the functions so that the caller can request that caches be left
alone.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file has changed quite a bit in the last 5 years as the capabilities
of the ECs have grown. Sync it up with the copy in coreboot commit
b9141f2215.
The only change is the addition of EC_VBNV_BLOCK_SIZE_V2. This is needed
because U-Boot uses the new v2 vboot API and this is not currently fully
supported by Chromium OS firmware.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name conflicts with the Chrome OS verified boot library, which
prevents it being built. That library uses a string whereas U-Boot uses a
64-bit hex value. Rename this in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a string.h header for libraries that expect this to be available, now
that U-Boot's version has moved to include/linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
We now have 99 tests. Before adding any more, rename everything to three
digits. This helps to preserve the ordering of tests and makes it easier
to find things.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are needed for the 2018 version of Chromium OS vboot. Add an
implementation for TPM v1, with v2 to come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this file uses logging but it should use the new macros. Update
it and add a log message for an error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the TPM drivers to use livetree (only one does not). Also,
sometimes TPMs can have child devices if they provide a service to the
system (such as storing secure data), so permit that.
Signed-off-by: Simon Glass <sjg@chromium.org>
All driver-model operation should return an error code. Adjust this
function to do so also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
When SPI flash operations fail it is helpful to be able to see the error
codes and where they are generated. Add logging to capture this
information for read operations.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we pass around a private pointer to specify the cros_ec device.
With driver model it makes more sense to pass the device. Update the code
to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases (e.g. sandbox with verified boot) it is useful to support
libfdt in TPL. Update the Kconfig to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this option applies to SPL, but it should be available in TPL
also, and separately. Change to using CONFIG_IS_ENABLED(), add a new
Kconfig option and fix up hang().
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible to specify that a node should be used before
relocation (in U-Boot proper) without it also ending up in SPL and TPL
device trees. Add a new "u-boot,dm-pre-proper" boolean property for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add Kconfig options so that the RTC can be used in SPL and TPL. This is
helpful for accessing the contents of CMOS RAM, for example.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is not possible to enable/disable block drivers in TPL. This
is needed to provide sandbox support. Add a Kconfig option and adjust the
Makefile.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the build fails in strange ways if CONFIG_SPL is defined by
CONFIG_SUPPORT_SPL is not. Add a warning for this case as it can be very
confusing to debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is necessary to read the keyboard in early phases of
U-Boot. Update the config to allow this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present spi_flash_cmd_read_ops() allocates and frees a few bytes of
memory every time it is called. It is faster to use the stack for this
and this is now supported by the minimum GCC version required by U-Boot.
Remove the allocation and use a variable-sized array instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode_read_fmap_entry() reads a flash map entry in a format
which is not supported by binman. To allow use to use binman-format
descriptions, update this function.
Also add a simple test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some devices have children and want to press an existing inactive child
into service when needed. Add a function to help with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Quite a few functions do not actually modify the device that is passed in.
Update the function signatures to reflect that.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no reason why this feature should not be supported for uclass-
private data. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox sets non-blocking I/O as soon as any input is read
from the terminal. However it does not restore the previous state on
exit. Fix this and drop the old os_read_no_block() function.
This means that we always enable blocking I/O in sandbox (if input is a
terminal) whereas previously it would only happen on the first call to
tstc() or getc(). However, the difference is likely not important.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we don't have to deal with the command-line flag we can simplify
the code for detecting the emulator. Remove the lookup based on the SPI
specification, relying just on the device tree to locate the emulator.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver was originally written against Chromium OS circa 2012. A few
new features have been added. Enhance the TPM driver to match. This mostly
includes a few new messages and properly modelling whether a particular
'space' is present or not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use an enum for command values instead of open-coding them. This removes
the need for comments. Also make sure the driver returns proper error
numbers instead of -1.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox assumes that device-tree control is active, but this
may not be the case in SPL or TPL. Add some conditions to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are many situations where sandbox syncs the display to
the SDL frame buffer. This is a very expensive operation but is only
needed every now and then. Update video_sync() so that we can specify
whether this operation is really needed.
At present this flag is not used on other architectures. It could also
be used for reducing writeback-cache flushes but the benefit of that would
need to be investigated.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add logging to aid debugging features in these drivers. Also drop some
code in sandbox_spi_xfer() which is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
When debugging sandbox it is sometimes annoying that the memory file is
deleted early on. If sandbox later crashes or we quit (using the
debugger), it is not possible to run it again with the same state since
the memory file is gone.
Remove the old memory file when sandbox exits, instead. Also add debugging
showing the memory filename.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to set the default log level from the command line
when running sandbox. Add a new -L command-line flag for this. The log
level is set using the enum log_level_t in log.h. At present a number must
be specified, e.g. -L7 for debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support booting from SPL to U-Boot proper. Add support for
the previous stage too, so sandbox can be started with TPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support specifying SPI flash devices to use in the device
tree and on the command line. Drop the second option, since it is a pain
to support nicely with driver model, and unnecessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
For debugging it is sometimes useful to write out data for inspection
using an external tool. Add a function which can write this data to a
given file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present to output a log message you need something like:
log(UCLASS_SPI, LOCL_INFO, "message1");
log(UCLASS_SPI, LOCL_INFO, "message2");
but many files use the same category throughout. Also it is helpful to
shorten the length of log names, providing helpers for common logging
levels. Add some macros so that it is possible to do:
(top of file, before #includes)
#define LOG_CATEGORY UCLASS_SPI
(later in the file)
log_info("message1");
log_debug("message2");
log_err("message3");
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way in configuration files (exlinux.conf for sysboot command)
to select a specific FIT configuration. The configuration is selected
with a string added after the FIT filename in the label "KERNEL" or
"LINUX", using the same format than bootm command:
KERNEL [Filename]#<conf>[#<extra-conf[#...]]
This configuration string, beginning by '#', is directly appended
to bootm argument 1 after <kernel_addr_r>.
bootm [<kernel_addr_r>]#<conf>[#<extra-conf[#...]]
see doc/uImage.FIT/command_syntax_extensions.txt for details
Example :
KERNEL /fit.itb#cfg1
KERNEL /fit.itb#cfg2
Configuration can be use also for overlay management :
KERNEL /fit.itb#cfg1#dtbo1#dtbo3
see doc/uImage.FIT/overlay-fdt-boot.txt for details
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The current mem_map definition for Meson SoCs has support for up
to 2GiB of RAM. According to S905, S905X, S912 and S805X datasheets
the DDR region is set from 0x00000000 to 0xBFFFFFFF, so mem_map's
definition should be changed accordingly.
It is also needed to be able to boot Khadas VIM2 board with S912
SoC.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
When traversing slots in a btree (via btrfs_path) with btrfs_next_slot(),
we didn't correctly identify that the last slot in the leaf was reached
and we should jump to the next leaf.
This could lead to any kind of runtime errors or corruptions, like:
* file data not being read at all, or is read partially
* file is read but is corrupted
* (any) metadata being corrupted or not read at all, etc
The easiest way to reproduce this is to read a large enough file that
its EXTENT_DATA items don't fit into a single leaf.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
This macro should have two parameters, not one. Fix it so that it
correctly resolves to _ret when logging is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the tests run one after the other using a single CPU. This is
not very efficient. Bring in the concurrencytest module and run the tests
concurrently, using one process for each CPU by default. A -P option
allows this to be overridden, which is necessary for code-coverage to
function correctly.
This requires fixing a few tests which are currently not fully
independent.
At some point we might consider doing this across all pytests in U-Boot.
There is a pytest version that supports specifying the number of processes
to use, but it did not work for me.
Signed-off-by: Simon Glass <sjg@chromium.org>
We only need to run driver-model tests with this config, since this is the
only thing that is different when CONFIG_OF_LIVE is not defined. Filter
out the other tests to same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present calling Uninit() always called ClearProgress() which outputs
a \r character as well as spaces to remove any progress information on the
line. This can mess up the normal output of binman and other tools. Fix
this by outputing this only when progress information has actually been
previous written.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a few test cases which print output. Suppress this so that tests
can run silently in the normal case.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this test runs binman twice, which means that the temporary
files from the first run do not get cleaned up. Split this into two tests
to fix this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present 'make check' leaves some temporary directories around. Part of
this is because we call tools.PrepareOutputDir() twice in some cases,
without calling tools.FinaliseOutputDir() in between.
Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This module is often available in the sandbox_spl build created by
'make check'. Use this as a default path so that just typing 'binman -t'
(without setting PYTHONPATH) will generally run the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'result' variable counts the number of failures in running the tests.
Rename it to 'failures' to make this more obvious. Also tidy up a few
comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the tests are run without any indication of what is running.
For the tests which start with a build this is pretty obvious, but for
tools it is not.
Add a name for each test we run, and print it before starting the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use 'make tests' to run the tests. For many projects
'make check' is more common, so support that as well. Also add some help
to 'make help'.
Signed-off-by: Simon Glass <sjg@chromium.org>
The filenames of the toolchains on kernel.org changes every now and then.
Fix it for the current change, and make the test use a regex so that it
has a better chance of passing with future changes too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the unicode filtering seems to get confused at times with
this error:
UnicodeDecodeError: 'ascii' codec can't decode byte 0x80 in position
32: ordinal not in range(128)
It seems to be due to self._nonprint being interpreted as UTF-8. Fix it
by using ordinals instead of characters, changing the string to set.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
With Python 2.7.15rc1, ConfigParser.SafeConfigParser has unfortunately
started returning unicode, for unknown reasons. Adjust the code to handle
this by converting everything to unicode. We cannot convert things to
ASCII since email addresses may be encoded with UTF-8.
Signed-off-by: Simon Glass <sjg@chromium.org>
On my Ubuntu 18.04.1 machine two driver-model bus tests have started
failing recently. The problem appears to be that the DATA region of the
executable is protected. This does not seem correct, but perhaps there
is a reason.
To work around it, unprotect the regions in these tests before accessing
them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Enables cmd_avb and its dependencies need to run the AVB tests.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[trini: Disable for sandbox_noblk]
Signed-off-by: Tom Rini <trini@konsulko.com>
Change get_sector_buf() to use map_sysmem() to get a pointer to the
CONFIG_FASTBOOT_BUF_ADDR in memory.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the pymark.buildconfigspec to depend on 'cmd_mmc' in addition to
'cmd_avb' for those tests that needs more a more complete MMC
implementation or the "mmc" command.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
With CONFIG_OPTEE_TA_AVB use the trusted application AVB provided by
OP-TEE to manage rollback indexes and device-lock status.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Tests the TEE uclass with a sandbox tee driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
[trini: initialize session to 0 in dm_test_tee]
Signed-off-by: Tom Rini <trini@konsulko.com>
Adds a sandbox tee driver which emulates a generic TEE with the OP-TEE
AVB TA.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Fix printf warnings in ta_avb_invoke_func, slots is uint]
Signed-off-by: Tom Rini <trini@konsulko.com>
Adds a sandbox_tee node to enable the sandbox tee driver in all the
sandbox dts files.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Adds configuration option OPTEE_TA_AVB and a header file describing the
interface to the Android Verified Boot 2.0 (AVB) trusted application
provided by OP-TEE.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Adds support in optee supplicant to route signed (MACed) RPMB frames
from OP-TEE Secure OS to MMC and vice versa to manipulate the RPMB
partition.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sync with 14e21cb8f811 ("arm64: dt: hikey: Add optee node"
from Linux kernel.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Adds a OP-TEE driver.
* Targets ARM and ARM64
* Supports using any U-Boot memory as shared memory
* Probes OP-TEE version using SMCs
* Uses OPTEE message protocol version 2 to communicate with secure world
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Sync with c8bfafb15944 ("dt/bindings: add bindings for optee")
from Linux kernel.
Introduces linaro prefix and adds bindings for ARM TrustZone based OP-TEE
implementation.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Adds a uclass to interface with a TEE (Trusted Execution Environment).
A TEE driver is a driver that interfaces with a trusted OS running in
some secure environment, for example, TrustZone on ARM cpus, or a
separate secure co-processor etc.
The TEE subsystem can serve a TEE driver for a Global Platform compliant
TEE, but it's not limited to only Global Platform TEEs.
The over all design is based on the TEE subsystem in the Linux kernel,
tailored for U-Boot.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Prior to this patch was do_avb_write_rb() reading supplied rb_idx as a
hexadecimal number while do_avb_read_rb() printed the read out rb_idx as
decimal number. For consistency change do_avb_read_rb() to print rb_idx
as a hexadecimal number too.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Just as /chosen may contain devices /firmware may contain devices, scan
for devices under /firmware too.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
The patch:
"spl: Weed out CONFIG_SYS_TEXT_BASE usage"
(sha1: 04ce5427bd)
introduced bug where assigning to u_boot_pos variable wasn't done
which end up in situation where SPL wasn't able to find out
image on the selected address.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This allows to boot all STM32F7 and STM32H7 boards independently
of the amount of embedded SDRAM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Avoid CoverityScan warning SIGN_EXTENSION by changing the type of
parameter size of set_cluster().
Avoid leaking stack content when writing an incomplete last sector.
Reported-by: Coverity (CID: 184096)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Do not leak filename_copy in case of error.
Catch out of memory when calling strdup.
Reported-by: Coverity (CID: 184086)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With there now being four device tree files, and 4 separate
defconfig files, the code necessary to determine which board is
being used is no longer necessary as the corresponding pin-muxing
and board names are determined by the device tree.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the device trees doing most of the work of pin-muxing and
DM doing much of the peripheral initialization, this creates
new defconfig files for each of the Logic PD variants with
proper register settings/pin-muxing.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update MAINTAINERS entry]
Signed-off-by: Tom Rini <trini@konsulko.com>
The baseboards and SOM's are virtually identical to their DM37
counterparts, but OMAP36/37 and OMAP3 have some minor register
differences. With the boards being mostly driven by device trees
now, this synchronizes their respective device trees with linux-omap
for-next branch destined for 4.20 (or whatever the version after 4.19
will be called)
Signed-off-by: Adam Ford <aford173@gmail.com>
With the introduction of the omap serial driver, the need for some
of these U-Boot specific modifications is gone. This cleans up
this unnneeded stuff.
Signed-off-by: Adam Ford <aford173@gmail.com>
The device tree entries are from linux-omap's for-next branch
destined to me put into 4.20 (or whatever the version is after 4.19)
Signed-off-by: Adam Ford <aford173@gmail.com>
Add support for the Arm Versatile Express config bus that is
being used for exposing various subsystems via a generic
configuration bus. This driver adds support for generating
transactions on this configuration bus and can be used by
other drivers to abstract the communication with the actual
function providers.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Instead of manually specifying CONFIG_SYS_EXTRA_ENV_RELOC
for every board that needs it, it shouldn't hurt to let
initr_reloc_global_data() always relocate gd->env_addr
unless we know this pointer is outside the initial binary.
To achieve this, the relocation is omitted if
CONFIG_ENV_ADDR is defined (and ENV_IS_EMBEDDED is not).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
After Siomon's comment, add a descriptive comment (docstring) to each of
helper functions in conftest.py. No functionality changed.
Signed-off-by: Akashi Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since there is no use of fs_type in umount_fs(), just remove it.
Signed-off-by: Akashi Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
After a test has failed, test/py drains the U-Boot console log to ensure
that any relevant output is captured. At this point, we don't care about
detecting any additional errors, since the test is already known to have
failed, and U-Boot will be restarted. To ensure that the test cleanup code
is not interrupted, and can correctly terminate the log sections for the
failed test, ignore any exception that occurs while reading the U-Boot
console output during this limited period of time.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Rockchip-focused changes for v2018.11-rc2:
- fixes to rkimage for SPL boot via USB
- fixes to make_fit_atf.py, incl. entry-point calculation and python3
compatibility
- OP-TEE support for ARMv7-based SoCs
- fixes to RGMII/GMII selection on the RK3328
Signed-off-by: Tom Rini <trini@konsulko.com>
Here we do a couple of impovements for all ARC boards
as well as introduce yet another developemnt board.
1. Now for ARC boards we print CPU and board info
which is useful for users and helps with
analysis of logs "post-mortem".
2. Synopsys IoT development kit support is added
This one might bw a bit too late as we're past RC1
but:
1) This doesn't affect any other arches etc
as we change purely ARC code.
2) I've got a chance to talk about U-Boot on
IoT platforms during ELCE (my proposal was on
a wait list and only this week I've got
an update and invitation to talk) so it would
be good to have this board as a primer in upstream
code-base by the time of ELCE 2018.
3) For complete support of IoT devkit I'm yet to
significantly rework regmap subsystem in U-Boot
but that's a different topic and hopefully it will
be done sometime soon... though not this release
cycle for sure.
The DesignWare ARC IoT Development Kit is a versatile platform
that includes the necessary hardware and software to accelerate
software development and debugging of sensor fusion,
voice recognition and face detection designs.
More information is avaialble here [1] and here [2].
The board is based on real silicon with
ARC EM9D-based Data Fusion IP Subsystem.
It sports a rich set of I/O including
* DW USB OTG
* DW MobileStorage (used for micro SD-card)
* GPIO
* multiple serial interface including DW APB UART
* ADC, PWM and eFlash, SRAM and SPI Flash memory
* Real-Time Clock (RTC)
* Bluetooth module with worldwide regulatory compliance
(FCC, IC, CE, ETSI, TELEC)
* On-board 9-axis sensor (gyro, accelerometer and compass)
Extensible with Arduino, Pmod, mikroBUS connectors and a 2x18
extension header.
One of the most interesting features for developers is built-in
Digilent USB JTAG probe so only micro-USB cable is needed!
[1] https://www.synopsys.com/dw/ipdir.php?ds=arc_iot_development_kit
[2] https://www.synopsys.com/dw/doc.php/ds/cc/iot_dev_kit.pdf
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
With implemented print_cpuinfo() and model property in .dts
we're ready to print nice info about ARC cores and boards on boot.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Even though arc-linux- prefix is used in ARC prebuilt tools and
in Buildroot there're other options like Linux distro cross-tools
etc where prefix is different so let's not rely on this default.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The 'rkimage' format used for booting rockchip boards over USB seems to
have been broken since commit 7bf274b9ca ("rockchip: mkimage: use
imagename to select spl hdr & spl size"). That commit adds an offset of
RK_SPL_HDR_START(=2048) to the location the 'RKxx' header is written
at. However the bootrom expects this header to be the first four bytes of
the image, not at offset 2048. This appears to have been a copy paste
error since the 'rksd' and 'rkspi' image types do require this offset.
Furthermore commit 111bcc4fb6 ("rockchip: mkimage: pad the header to
8-bytes (using a 'nop') for RK3399"), commit 3d54eabcaf ("rockchip:
spl: RK3399: use boot0 hook to create space for SPL magic") and
commit 3082775692 ("rockchip: mkimage: update rkimage to support
pre-padded payloads") changed the way the space for the 'RKxx' header is
allocated and written to the image without adjusting 'rkimage'.
This commit fixes those mistakes and makes it possible to load u-boot SPL
over USB once more.
(Tested on RK3399)
Signed-off-by: Daniel Gröber <daniel@dps.uibk.ac.at>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
u-boot.itb depends on u-boot-nodtb.bin, which in turn depends on u-boot.
u-boot.its from Rockchip make_fit_atf.py (used by {evb,firefly}-rk3399)
wants to read u-boot but is lacking this dependency, so that u-boot.itb
cannot be built in one go. Detect its use and add the missing dependency.
Reported-by: Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using PHY internal delays in combination with the phy-mode
rgmii-id/rxid/txid was not possible. Only rgmii was supported.
Now we can disable rockchip's gmac delay lines and also use
rgmii-id/rxid/txid.
Based on commit eaf70ad14cbb ("net: stmmac: dwmac-rk: Add
handling for RGMII_ID/RXID/TXID") for mainline linux kernel.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We have to use RK3328_RXCLK_DLY_ENA_GMAC_ENABLE instead of
RK3328_RXCLK_DLY_ENA_GMAC_MASK in rk3328_gmac_set_to_rgmii()
to enable the RX delay.
The MASK was used in a wrong way.
Signed-off-by: Janine Hagemann <j.hagemann@phytec.de>
Reviewed-by: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
make_fit_atf.py uses physical address of first segment as the
entry point to bl31. It is incorrect and causes following abort
when bl31_entry() is called:
U-Boot SPL board initTrying to boot from MMC1
"Synchronous Abort" handler, esr 0x02000000
elr: 0000000000000000 lr : 00000000ff8c7e8c
x 0: 00000000ff8e0000 x 1: 0000000000000000
x 2: 0000000000000000 x 3: 00000000ff8e0180
x 4: 0000000000000000 x 5: 0000000000000000
x 6: 0000000000000030 x 7: 00000000ff8e0188
x 8: 00000000000001e0 x 9: 0000000000000000
x10: 000000000007fcdc x11: 00000000002881b8
x12: 00000000000001a2 x13: 0000000000000198
x14: 000000000007fdcc x15: 00000000002881b8
x16: 00000000003c0724 x17: 00000000003c0718
x18: 000000000007fe80 x19: 00000000ff8e0000
x20: 0000000000200000 x21: 00000000ff8e0000
x22: 0000000000000000 x23: 000000000007fe30
x24: 00000000ff8d1c3c x25: 00000000ff8d5000
x26: 00000000deadbeef x27: 00000000000004a0
x28: 000000000000009c x29: 000000000007fd90
Fix it by using the entry point from the elf header.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
OP-TEE is an open source trusted OS, in armv7, its loading and
running are like this:
loading:
- SPL load both OP-TEE and U-Boot
running:
- SPL run into OP-TEE in secure mode;
- OP-TEE run into U-Boot in non-secure mode;
To make code simple, it would be fine to use IH_OS_TEE for the
os tyle in TPL(just like IH_OS_LINUX is using both in SPL and U-Boot).
Here is the diagram for SPL loading OP-TEE,
IH_OS_TEE:(make u-boot.itb for SPL)
Non-Secure Secure
BootROM
|
v
SPL
|
v
--------- OP-TEE
|
v
U-Boot
|
V
Linux
For other two king of OP-TEE loading/booting, see commit message:
45b55712d4 image: Add IH_OS_TEE for TEE chain-load boot
More detail:
https://github.com/OP-TEE/optee_os
and search for 'boot arguments' for detail entry parameter in:
core/arch/arm/kernel/generic_entry_a32.S
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Patch fix warning:
/builddir/BUILD/u-boot-2018.05-rc2/"arch/arm/mach-rockchip/make_fit_atf.py" \
arch/arm/dts/rk3399-firefly.dtb > u-boot.its
./tools/mkimage -f u-boot.its -E u-boot.itb >/dev/null && cat
/dev/null
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/uboot@1
has a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@2 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/atf@3 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node /images/fdt@1 has
a unit name, but no reg property
u-boot.itb.tmp: Warning (unit_address_vs_reg): Node
/configurations/config@1 has a unit name, but no reg property
make[1]: Leaving directory
'/builddir/BUILD/u-boot-2018.05-rc2/builds/firefly-rk3399'
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch adds the SPI driver for the MediaTek MT7688 SoC (and
derivates). Its been tested on the LinkIt Smart 7688 and the Gardena
Smart Gateway with and SPI NOR on CS0 and on the Gardena Smart
Gateway additionally with an SPI NAND on CS1.
Note that the SPI controller only supports a max transfer size of 32
bytes. This driver implementes a workaround to enable bigger xfer
sizes to speed up the transfer especially for the SPI NAND support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Piotr Dymacz <pepe2k@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds support for 2 new XMC (Wuhan Xinxin Semiconductor
Manufacturing Corp) SPI NOR chips.
This support can be enabled by selecting the SPI_FLASH_XMC Kconfig
option.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Additional sgmii phymode is added in socfpga_phymode_setup() along with
a minor fix for maximum number of GMACs.
Signed-off-by: Ooi, Joyce <joyce.ooi@intel.com>
Fix sfp_verify_header to return correct version number.
This fixes "Not a sane SOCFPGA preloader" error message with v1 header.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Change to use managed resource function devm_kcalloc(),
so it will auto free memory when driver is removed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a PHY driver for the R-Car Gen3 which allows configuring
USB OTG PHY on Gen3 into host mode and toggles VBUS in case a
dedicated regulator is present.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark area 0x1_0000_0000 - 0x10_0000_0000 as DRAM on Gen3 as the
chip is capable of addressing that and U-Boot can make use of it.
This patch prevents exception when accessing those areas.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The CPfi/4 is derived from XTAL clock and is not fixed. Undo
the previous commit 7984ac8d1635aebd11175c96b07f937a39f0384d.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The I2C6 is used to communicate with the PMIC and it was removed
during DT sync with Linux 4.17. Reinstate it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
If environment variable CROSS_COMPILE is not set, this indicates native
compilation. In this case we should not set an arbitrary value which is
not applicable for 64bit anyway.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The Sentence "reset unsupported yet" is not
grammatically correct and should say
"reset not supported yet" instead.
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Rick Chen <rick@andestech.com>
We don't have a reset method on any RISC-V board yet. Instead of
adding the same 'unsupported' message for each CPU variant it might
make more sense to add a generic do_reset function for all CPU
variants to lib/, similar to the one for ARM (arch/arm/lib/reset.c).
Suggested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This adds QEMU RISC-V 'virt' board target support, with the hope of
helping people easily test U-Boot on RISC-V.
The QEMU virt machine models a generic RISC-V virtual machine with
support for the VirtIO standard networking and block storage devices.
It has CLINT, PLIC, 16550A UART devices in addition to VirtIO and
it also uses device-tree to pass configuration information to guest
software. It implements RISC-V privileged architecture spec v1.10.
Both 32-bit and 64-bit builds are supported. Support is pretty much
preliminary, only booting to U-Boot shell with the UART driver on
a single core. Booting Linux is not supported yet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Currently start.S is inside arch/riscv/cpu/ax25/, but it can be
common for all RISC-V targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
There is no reason to keep two versions of CSR read/write defines
in encoding.h. We already have one set of defines in csr.h, which
is from Linux kernel, and let's drop the one in encoding.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This adds a helper routine to print CPU information. Currently
it prints all the instruction set extensions that the processor
core supports.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
At present the compiler flag against which architecture and abi
variant the riscv image is built for is not explicitly indicated
which means the default compiler configuration is used. But this
does not work if we want to build a different target (eg: 32-bit
riscv images using a toolchain configured for 64-bit riscv).
Fix this by explicitly passing -march and -mabi to the compiler.
Since generically we don't use floating point in U-Boot, specify
the RV[32|64]IMA ISA and software floating ABI.
This also fix some alignment coding style issues.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The first argument of Linux kernel is the risc-v core hart id,
from which the kernel is booted from. It is not the mach_id,
which seems to be copied from arm.
While we are here, this also changes the Linux kernel entry
parameters' type to support both 32-bit and 64-bit.
Note the hart id is hardcoded to zero for now, and we should
change to fill in it with the value read from mhartid CSR of
the hart which this routine is currently running on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Rick Chen <rick@andestech.com>
This was copied from ARM, and does not apply to RISC-V. While we
are here, bootm.h is eventually removed as its content is only
the inclusion of setup.h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
The Arm Versatile Express I2C controller is a simple register-based
controller that uses a register to control the state of the SCL and
SDA lines. Add support for it.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add DM support to the SH QSPI driver while retaining non-DM support.
The later is required as this driver is used in SPL which has a size
limitation of 16 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
[jagan: use proper commit head]
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add code to reset all reset signals as in SPI DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Release reset when _remove().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Instead of collecting partitions in a flat list, create a hierarchy
within the mtd_info structure: use a partitions list to keep track of
the partitions of an MTD device (which might be itself a partition of
another MTD device), a pointer to the parent device (NULL when the MTD
device is the root one, not a partition).
By also saving directly in mtd_info the offset of the partition, we
can get rid of the mtd_part structure.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Using an MTD device (resp. partition) name in mtdparts is simple and
straightforward. However, for a long time already, another name was
given in mtdparts to indicate a device (resp. partition) so the
"mtdids" environment variable was created to do the match.
Let's create a function that, from an MTD device (resp. partition)
name, search for the equivalent name in the "mtdparts" environment
variable thanks to the "mtdids" string.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The current parser is very specific to U-Boot mtdparts implementation.
It does not use MTD structures like mtd_info and mtd_partition. Copy
and adapt the current parser in drivers/mtd/mtd-uclass.c (to not break
the current use of mtdparts.c itself) and write some kind of a wrapper
around the current implementation to allow other commands to benefit
from this parsing in a user-friendly way.
This new function will allocate an mtd_partition array for each
successful call. This array must be freed after use by the caller.
The given 'mtdparts' buffer pointer will be moved forward to the next
MTD device (if any, it will point towards a '\0' character otherwise).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
The user might want to trigger the probe of any MTD device, export these
functions so they can be called from a command source file.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
include/mtd.h might be included by files even if CONFIG_DM is not
enabled. In this case, the call to dev_get_uclass_priv() would trigger
a build error. Because this helper has no user, let's drop it off.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
It is good practice to make the setting of gpio-pinctrls explicitly in the
devicetree, and in this case even necessary.
Rockchip boards start with iomux settings set to gpio for most pins and
while the linux pinctrl driver also implicitly sets the gpio function if
a pin is requested as gpio that is not necessarily true for other drivers.
The issue in question stems from uboot, where the sdmmc_pwr pin is set
to function 1 (sdmmc-power) by the bootrom when reading the 1st-stage
loader. The regulator controlled by the pin is active-low though, so
when the dwmmc hw-block sets its enabled bit, it actually disables the
regulator. By changing the pin back to gpio we fix that behaviour.
[picked from the identical linux patch
https://patchwork.kernel.org/patch/10609253/]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dwmmc controllers on rk3188 do not have idma support, so need to
use the fifo-mode and it my tests they became confused and stopped
working if the frequency was to high.
While I only tested in somewhat bigger steps, 32MHz for example
hung the controller, while reducing it to 16MHz worked just fine
and is reasonably fast to load a kernel from mmc.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
While trying to enable the dw_mmc on rk3188 I managed to confuse
and hang the dw_mmc controller into not delivering further data.
The fifo state never became ready and the driver was iterating in
the while loop reading 0-byte packets forever.
So inspired by how other implementations handle this, check the fifo-
state beforhand and add a timeout to catch any glaring fifo issues
without hanging uboot altogether.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Behun <marek.behun@nic.cz>
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
MSM variant of Chipidea must reinitalize the phy
after controller reset.
Introduce ci_init_after_reset() weak function that
can be used to achieve the above init.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add a PHY driver for the Qualcomm dragonboard 410c which
allows switching on/off and resetting the phy connected
to the EHCI controllers and USBHS controller.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The serial# environment variable needs to be
defined so it will be used by fastboot as serial
for the endpoint descriptor.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Since commit 7b3b74d321 ("serial: serial_stm32: Enable overrun")
on STM32F7xx based boards, the first lines of serial output are
missing during boot (we no more see the U-Boot release version,
board model and DRAM size).
By enabling the uart FIFO on STM32F7, the complete U-boot log
can be sent correctly.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
The escape sequence '\#' does not work for the latest GNU Make from
the git tree.
Replace it with $(pound) as Linux did.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ commit 9564a8cf422d7b58f6e857e3546d346fa970191e in Linux ]
I tried building using a freshly built Make (4.2.1-69-g8a731d1), but
already the objtool build broke with
orc_dump.c: In function ‘orc_dump’:
orc_dump.c:106:2: error: ‘elf_getshnum’ is deprecated [-Werror=deprecated-declarations]
if (elf_getshdrnum(elf, &nr_sections)) {
Turns out that with that new Make, the backslash was not removed, so cpp
didn't see a #include directive, grep found nothing, and
-DLIBELF_USE_DEPRECATED was wrongly put in CFLAGS.
Now, that new Make behaviour is documented in their NEWS file:
* WARNING: Backward-incompatibility!
Number signs (#) appearing inside a macro reference or function invocation
no longer introduce comments and should not be escaped with backslashes:
thus a call such as:
foo := $(shell echo '#')
is legal. Previously the number sign needed to be escaped, for example:
foo := $(shell echo '\#')
Now this latter will resolve to "\#". If you want to write makefiles
portable to both versions, assign the number sign to a variable:
C := \#
foo := $(shell echo '$C')
This was claimed to be fixed in 3.81, but wasn't, for some reason.
To detect this change search for 'nocomment' in the .FEATURES variable.
This also fixes up the two make-cmd instances to replace # with $(pound)
rather than with \#. There might very well be other places that need
similar fixup in preparation for whatever future Make release contains
the above change, but at least this builds an x86_64 defconfig with the
new make.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=197847
Cc: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If we fail to find the MMC boot device, report the number of the one
we were looking for in the error to aid diagnosis.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The Arm Versatile Express and Juno development boards contain an
OSC clock generator that can be accessed through the Versatile
Express config bus. The generators are quite often being controlled
by some MCU and the config bus offers a uniform way of exposing them.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a test which verifies that all subnodes under "/firmware"
nodes are scanned.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Added 'imply FIRMWARE' to sandbox Kconfig to fix test failures, fixed
ordering of lines in arch/sandbox/dts/test.dts and test/dm/Makefile,
updated #if condition in drivers/firmware/firmware-uclass.c:
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no prompt string for FIRMWARE config. Without this,
FIRMWARE config cannot be enabled through menuconfing or
config file. Fix this by adding prompt summary.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Something has changed in the last several month such that when buildman
builds U-Boot incrementally and a new CONFIG option has been added to the
Kconfig, the build hanges waiting for input:
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Since binamn does not connect the build's stdin to anything this waits on
stdin to the build thread, which never comes. Eventually I suspect all the
threads end up in this state and the build does not progress.
Fix this by passing /dev/null as input to the build. That way, if there is
a new CONFIG, the build will stop (and fail):
Test new config (NEW_CONFIG) [N/y/?] (NEW)
Error in reading or end of file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Remove duplicated inclusion of dm/ofnode.h
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
The comment references a structure name that doesn't exist. Use
the name of the actual uclass.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Drop period at end of commit subject:
Signed-off-by: Simon Glass <sjg@chromium.org>
Converts fdtdec_setup_memory_banksize() to use ofnode functions instead.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Since there is no canonical "board device" that can be used in board
files, it is difficult to use DM function for board initialization in
these cases.
Hence, add a uclass that implements a simple "board device", which can
hold devices not suitable anywhere else in the device tree, and is also
able to read encoded information, e.g. hard-wired GPIOs on a GPIO
expander, read-only memory ICs, etc. that carry information about the
hardware.
The devices of this uclass expose methods to read generic data types
(integers, strings, booleans) to encode the information provided by the
hardware.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We cannot use device structures to disable devices, since getting
them with the API functions would bind and activate the device, which
would fail if the underlying device does not exist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for the ofnode_set_enabled, ofnode_write_string, and
ofnode_write_property functions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Implement a set of functions to manipulate properties in a live device
tree:
* ofnode_write_prop() to set generic properties of a node
* ofnode_write_string() to set string properties of a node
* ofnode_set_enabled() to either enable or disable a node
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we get a problem like overlapping regions it is sometimes hard to
figure what what is going on. At present we don't write the map file in
this case. However the file does provide useful information.
Catch any packing errors and write a map file (if enabled with -m) to aid
debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we want to put ELF files in the image since that is what we
need to execute. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Normally x86 platforms use the end-at-4gb option. This currently produces
an FMAP with positions which have a large offset. The use of end-at-4gb is
a useful convenience within binman, but we don't really want to export
a map with these offsets.
Fix this by subtracting the 'skip at start' parameter.
Also put the code which convers names to fmap format, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sections have no record of their parent so it is not possible
to traverse up the tree to the root and figure out the position of a
section within the image.
Change the constructor to record this information.
Signed-off-by: Simon Glass <sjg@chromium.org>
When TPL is used on x86 we may want to program the microcode (at least for
the first CPU) early in boot. Add support for this by refactoring the
existing code to be more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimesi it us useful to be able to verify the content of entries with
a hash. Add an easy way to do this in binman. The hash information can be
retrieved from the device tree at run time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Images and sections have the same attributes, since an image is mostly
just a top-level section. Update the docs to explain this.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to add a group of files to the image and be
able to access them at run-time. Of course it is possible to generate
the binman config file with a set of blobs each with a filename. But for
convenience, add an entry type which can do this.
Add required support (for adding nodes and string properties) into the
state module.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if there is only a zero-size entry in a section this is
reported as an error, e.g.:
Offset 0x0 (0) is outside the section starting at 0x0 (0)
Adjust the logic in CheckEntries() to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for compressing blob entries. This can help reduce image sizes
for many types of data. It requires that the firmware be able to
decompress the data at run-time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the pinctrl function enabled and the device tree setting up
the pins we want to use, this patch removes the manual pinmuxing
except for that which is not done by the device tree and minimal
pins necessary for SPL (like serial, GPMC, and MMC)
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_I2C and DM_GPIO working, this patch can enable the
GPIO expander on the I2C bus. This GPIO expander is connected
to some of the DIP switches and can now read the status of these
pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
The simple pin controller works for da850, so this patch enables
this to pin-mux the pins defined in the device tree for the da850evm.
Signed-off-by: Adam Ford <aford173@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: Adam Ford <aford173@gmail.com>
Previously poweroff was located under boot. It seems to make more
sense to have it located under the Device access commands.
Signed-off-by: Adam Ford <aford173@gmail.com>
With the omap_mmc driver no longer supporting cd-inverted, this
patch removes all these references since they are not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add commands for fdt overlay merging. This is required for the boot scripts
that detect PDAs and apply specific overlays to the DTB passed on to kernel.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This adds the support for PDA detection as common code for
Atmel boards.
Using the one wire interface over GPIO , an EEPROM memory is read
and compared to preprogrammed values for PDA screens TM4300, TM7000
and TM7000B.
Once the PDA is detected, an environment variable is set accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D4 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D3 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SAMA5D2 SoC can have extra clip boards (PDAs) connected, which have
an EEPROM memory for identification. A special GPIO can be used to read
this memory over 1wire protocol.
Enabling one wire and eeprom drivers for this memory.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To be able to test Dallas onewire protocol and one wire eeproms driver
and subsystem, add in sandbox defconfig the drivers' config.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add basic command for bus information and read for onewire
bus using Dallas 1-Wire protocol.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a driver that supports Maxim 1 wire EEPROMs families
DS24B33 and DS2431.
Can be extended for other families as well.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked driver]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a new device is discovered, this may be a w1 eeprom device.
Attempt to find the proper node and driver from the w1-eeprom subsystem.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to access data stored onto one wire EEPROMs.
Create a framework to provide a consistent API.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked patch]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a bus driver for bitbanging a 1-Wire bus over a GPIO.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: fixed some issues]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We might want to use 1-Wire devices connected on boards such as EEPROMs in
U-Boot.
Provide a framework to be able to do that.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
[eugen.hristev@microchip.com: reworked]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This is file system generic loader which can be used to load
the file image from the storage into target such as memory.
The consumer driver would then use this loader to program whatever,
ie. the FPGA device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add a document to describe file system firmware loader binding
information.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide information about
- overview of file system firmware loader driver model
- describe storage device and partition in device tree source
- describe fie system firmware loader API
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to find the block device descriptor of the parent
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[trini: Move function declaration to avoid warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Arm Mali Display Processors DP500, DP550 and DP650.
Only one layer is being used to display the console or boot logo,
even if more layers are supported in the hardware.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
When tools are needed but not present, at present we just get an error
which can be confusing for the user. Try to be helpful by reporting the
tool as missing and suggesting a possible remedy.
Also update the Run() method to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binman currently supports updating the main device tree with things like
the position of each entry. Extend this support to SPL and TPL as well,
since they may need (a subset of) this information.
Also adjust DTB output files to have a .out extension since this seems
clearer than having a .dtb extension with 'out' in the name somwhere.
Also add a few missing comments and update the DT setup code to use
ReadFile and WriteFile().
Signed-off-by: Simon Glass <sjg@chromium.org>
We use a fake device tree in tests most of the time since tests don't
normally care about the actual data. For example, for U-Boot proper we use
U_BOOT_DTB_DATA which is just a four-character string. This makes testing
the image output against an expected value very easy.
However in some cases, such as when the test wants to check that the DT
output containing particular nodes, we do actually need the real DT. Add
support for this, along with a command-line option to select 'test mode'.
Signed-off-by: Simon Glass <sjg@chromium.org>
We always have a device tree for U-Boot proper. But we may also have one
for SPL and TPL. Add a new Entry method to find out what DTs an entry
has, and use that list when updating DTs.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we have a few calls to device-tree functions in binman and plan
to add more as we add new entry types which need to report their results.
It makes sense to put this code in a central place so that we can make
sure all device trees are updated. At present we only have U-Boot proper,
but plan to add SPL and TPL too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the control module has state information in it, since it is the
primary user of this. But it is a bit odd to have entries and other
modules importing control to obtain this information.
It seems better to have a dedicated state module, which control can use as
well. Create a new module using code from control and update other modules
to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Various entry implementations provide a way to obtain the default filename
for an entry. But at present there is no base-class implementation for
this function. Add one so that the API is defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few more functions which allow creating and modifying property
values. If only we could do this so easily in the real world.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we require the caller to manually update the device tree using
individual calls to libfdt functions. This is not ideal. It would be
better if we could make changes using the Python structure and then call a
Sync() function to write them back.
Add this feature to the Fdt class. Update binman and the tests to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to build only a subset of the images provided by
the binman configuration. Add a -i option for this. It can be given
multiple times to build several images. If the option is not given, all
images are built.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if there are two vblock entries an image their contents are
written to the same file in the output directory. This prevents checking
the contents of each separately.
Fix this by adding part of the entry path to the filename, and add some
missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we want to include TPL for x86 platforms, such as when we want
to select between different SPL images (e.g. for Chrome OS verified boot).
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When the value of a text entry is not provided an execption is generated
talking about a None type. This is confusing. Add a more explanatory error
and a test for this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Pull this support from these upstream commits:
bfbfab0 pylibfdt: Add a means to add and delete notes
9005f41 pylibfdt: Allow delprop() to return errors
Signed-off-by: Simon Glass <sjg@chromium.org>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 5d9ef839f874f4e3923c8a9ae7b136c6c3912cd5
Author: Stefan Mavrodiev <stefan@olimex.com>
Date: Wed May 16 14:38:08 2018 +0300
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
Note:
- Update sun7i-a20-primo73.dts as per Linux, since
this dts is U-Boot specific.
- Drop sun7i-a20-olimex-som-evb-emmc.dts since no board
added for this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10s/A13/gr8/r8devicetree dtsi and dtsi files from
Linux-v4.18-rc3 with below commit:
commit 190e3138f9577885691540dca59c2f07540bde04
Merge: cafc87023b0d a7affb13b271
Author: Arnd Bergmann <arnd@arndb.de>
Date: Tue Mar 27 14:58:00 2018 +0200
Merge tag 'sunxi-h3-h5-for-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Update all A10 devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 590b0c0cfc6162aeebbf43eaafb9753b56df1532
Author: Pascal Roeleven <dev@pascalroeleven.nl>
Date: Fri Apr 20 12:21:12 2018 +0200
ARM: dts: sun4i: Fix incorrect clocks for displays
Note: Update pinctrl-0 for sun4i-a10-inet-3f.dts, sun4i-a10-inet-3w.dts
like other dts file since there dts file are U-Boot specific.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
video_init, video_putc and video_puts functions are not implemented
anywhere, remove their declaration from the header.
Signed-off-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add tests for the hex2bin, bin2hex, and hex_to_bin functions, which were
recently added to U-Boot.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a unit test assert-method, which compares two given memory areas for
byte-wise equality.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some devices offer a text-based OSD (on-screen display) that can be
programmatically controlled (i.e. text displayed on).
Add a uclass to support such devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The EFI subsystems needs to know the size of the terminal. If the
environment variable
stdout = serial,vidconsole
this size cannot be read from the video console. So the EFI subsystem
sends escape sequences to read the size. With this patch we get support
for the following escape sequences:
ESC "7" Save cursor position
ESC "8" Restore cursor position
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The include/video*.h files are part of the drivers in drivers/video. So it
makes sense to assign them to the same maintainer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add device tree for T2080QDS board and enable CONFIG_OF_CONTROL
so that device tree can be compiled.
Update board README for device tree usage.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Below is the sequence to embed dtb inside U-Boot,
1. Remove bootpg and resetvec section if needed
2. Append dtb
3. Append bootpg and resetvec section back if removed in step 1
Above procedure is required only when CONFIG_MPC85xx and
CONFIG_OF_SEPARATE are defined.
Add new config CONFIG_MPC85XX_HAVE_RESET_VECTOR to indicate that
image has resetvec section. Step 1 and step 3 described above are
required only if this config is y.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently binman calculates '_skip_at_start' based on 'end-at-4gb'
property and it is used for x86 images.
For PowerPC mpc85xx based CPU, CONFIG_SYS_TEXT_BASE is the entry
offset of the first entry. It can be 0xeff40000 or 0xfff40000 for
nor flash boot, 0x201000 for sd boot etc, so "_skip_at_start"
should be set to CONFIG_SYS_TEXT_BASE.
'end-at-4gb' property is not applicable where CONFIG_SYS_TEXT_BASE +
Image size != 4gb.
Add new property 'skip-at-start' in Section class so that
'_skip_at_start' can be calculated either based on 'end-at-4gb'
or based on "skip-at-start".
Add a test case to check that 'skip-at-start' and 'end-at-4gb'
property can't be used together.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
'board_fdt_blob_setup' function sets up fdt blob at '&_end' so
define '_end' symbol in mpc85xx lds files.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Recently the FMan Port and MAC compatibles were changed. This patch
aligns the FMan Port and MAC compatibles to the new FMan device tree
binding document. The FMan device tree binding document can be found
in the Linux kernel version 3.18.0, commit
297d35fd2a7d3fbd4e5c0f0c1c18213117ba11ba
./Documentation/devicetree/bindings/powerpc/fsl/fman.txt
This patch doesn't affect legacy compatibles support.
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for ICID setup of qman portals and the required device
tree fixups.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reuse the existing ICID setup code done for LS1046A smmu enablement
and add the equivalent setup for LS1043A chips.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory reserved for Management Complex needs to be cleaned before any
usage.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The iommu-map property in the fsl-mc node is updated by
valid stream-ids by u-boot. This patch is to fixup this
property for LS208x and LS1088.
Signed-off-by: Nipun Gupta <nipun.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012AFRWY supports three board revisions.
Revision A and B board are collectively identified as revA/B,
Revision C board is identifies as revC.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
[York S: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
At present the MMC subsystem maintains its own list of MMC devices.
This cannot work with driver model when CONFIG_BLK is enabled, use
blk_dread to replace previous mmc read interface, use
mmc_get_blk_desc to get the mmc device property.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
[York S: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Xilinx changes for v2018.11
- Handle BOARD_LATE_INIT via Kconfig
SPL:
- Enable GZIP for all partitions types(not only for kernel)
ZynqMP:
- Rearrange pmufw version handling
- Support newer PMUFW with improved fpga load sequence
Zynq:
- Cleanup config file
- Simplify zybo config by enabling option via Kconfig
net:
- Fix gems max-speed property reading
- Enable support for fixed-link phys
Based on dt-specs fixed-link doesn't require phy-handle to be used.
Fix driver to only read phy related setting when phy-handle is found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
When running sandbox with the new pointer sanitization we just recently
introduced, we're running into a case with FIT images where we end up
interpreting pointers as addresses.
What happened is that most callers of set_working_fdt_addr() simply
convert pointers into addresses without taking into account that they
might be 2 separate address spaces. Fix the callers up to map their
pointers into addresses.
This makes sandbox tests pass for me again.
Signed-off-by: Alexander Graf <agraf@suse.de>
Only add CONFIG_DISPLAY to defconfig because CONFIG_I2C_EDID
is automatically selected by CONFIG_DISPLAY
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
max-speed property is part of phynode and it has to be
read using ofnode_read_u32_default(). This fixes the issue
of incorrect max-speed read from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to limit gzip usage only for OS_BOOT and kernel image
type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: York Sun <york.sun@nxp.com>
This patch modifies PL bitstream loading sequence as per
latest Xilfpga which supports all variants of bitstream images
generated from vivado and from bootgen. With this new change in
Xilfpga, uboot doesn't need to validate and swap bitstream as it will
be taken care inside Xilfpga. ZynqMP PL driver now checks for supporting
PMUFW version before skipping the validation and swap sequence as there
can be old PMUFW which doesn't supports this feature. In this case, driver
uses old way of PL bitstream loading sequence.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify the zynqmp_pmufw_version() routine to return PMUFW version so
that it can be reused wherever required. Get PMUFW version from PMU
only once at bootup and later just return stored value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the PM version related macros to .h file so that
they can be reused in other files.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that we already disable the "strict-aliasing" globally, remove
the duplicates in the nds32/riscv/x86 arch-specific Makefiles.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The -fstrict-aliasing option is implicitly enabled at levels -O2,
-O3, -Os by GCC. This option allows the compiler to assume the
strictest aliasing rules applicable to the language being compiled.
For example, the practice of reading from a different union member
than the one most recently written to (called "type-punning") is
common. In this case, "type-punning" only works if the memory is
accessed through the union type, but might not work by taking the
address, casting the resulting pointer and dereferencing the result,
which is an undefined behavior per the "strict aliasing rules".
GCC's -Wstrict-aliasing (included in -Wall) option does not catch
all cases, but does attempt to catch the more common pitfalls. So
there are cases that GCC does not report but the codes are violating
the "strict aliasing rules".
Given lots of codes that may be written to rely on "type-punning",
and Linux kernel disables it by -fno-strict-aliasing globally, since
U-Boot currently does this on nds32/riscv/x86 builds only, extend
this for all architecture builds.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
AM654 uses a UART controller that is compatible (partially) with
existing OMAP UART, Introduce a compatible for adding support
for this controller.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This option has never been used for anything. Drop it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
These options are not used or necessary when device model is being used
for SCSI. Just drop them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using device model this sort of hardcoded limits aren't used or
necessary.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
The loop in ahci_start_ports() is looping over the maximum number of
SCSI devices in the system, which can be larger than the amount of ports
a particular AHCI controller has. The extra looping isn't directly
harmful because the link_port_map bitmap won't have the bit set for a
nonexistent port, but it is wasteful. Replace the loop limit with the
port count of the AHCI controller instead.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make use of asm-generic/atomic.h retaining the smp_mb_... definitions.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The arm, xtensa and mips version of atomic.h were already very similar
(the mips one was a copy of xtensa). Combine these implementations
together to produce a generic atomic.h that can be included by these
architectures (and any others that need it in future).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'conitrace' command prints the codes received from the console input as
hexadecimal numbers.
This developer utility is useful for testing the handling of special keys
by keyboard drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
In the section about Device Trees add a paragraph at the end that
clarifies how we decide of a tree is valid or not. We say that all
bindings must either be in the specification (link provided) or in our
device-tree-bindings directory. We say that most of these come from the
Linux Kernel and as such some design decisions are made for us already,
but that in most cases we wish to retain compatibility.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SSP2 clock is at bit 6 in the register, so the value is 0x40 unlike
the current 0x70 which enables the clock of UART2, SSP1 and SSP2.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Stefan Roese <sr@denx.de>
SPI controllers SSP1, 2 and 3 require to enable their respective clocks.
Let's enable them only when the SPI controller driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
This adds support for the ARM PL022 SPI controller for the standard
variant (0x00041022) which has a 16bit wide and 8 locations deep TX/RX
FIFO.
A few parts were borrowed from the Linux kernel driver.
Cc: Armando Visconti <armando.visconti@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Enable CONFIG_OF_BOARD_SETUP as it is needed for Beaglebone
black to overwrite the Ethernet phy address present in DT
in case the phy latches on to a different address.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On beaglebone black, it can so happen that PHY address
is not latched correctly on reset and board boots with
PHY responding to a different address than that
programmed in device-tree. For example, see this report:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Workaround this by fixing up device-tree passed to kernel
by using the PHY address detected in hardware.
Beaglebone itself uses only one ethernet port and its DT
currently uses phy_id (obsoleted). But the function has
been written to handle multiple ports and phy_id as well
as phy-handle to make the function more generically useful.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some boards using TI CPSW, it may be possible that
PHY address was not latched correctly, and the actual
address that the phy responds on is different from that
set in device-tree. For example, see this problem report
on beaglebone black:
https://groups.google.com/d/msg/beagleboard/9mctrG26Mc8/1FuI_i5KW10J
Add support to check for this condition and use the
detected phy address when its safe to do so.
Also, add a public API that exposes the phy address of
a given slave. This can be used to update device-tree that
is passed to Linux kernel.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds a defconfig for sama5d27_som1_ek board to get environment from
uSD. The defconfig is made from sama5d27_som1_ek_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
uSD. The environment is expected to be found in uSD's FAT partition.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
CONFIG_BOOTARGS can be set using Kconfig, so we no longer need it
in the config files.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
FAT_ENV_xxx options can now be set using Kconfig, so we no longer
need them in the config files.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
This adds a defconfig for sama5d2_xplained board to get environment from
eMMC. The defconfig is made from sama5d2_xplained_mmc_defconfig, with
'bootcmd' and 'bootargs' changed to kernel, device-tree and rootfs from
eMMC. The environment is expected to be found in eMMC's FAT
partition.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
The SPL loaders assume that the CONFIG_SYS_TEXT_BASE memory location
is available and can be corrupted by loading ie. uImage or fitImage
headers there. Sometimes it could be beneficial to load the headers
elsewhere, ie. if CONFIG_SYS_TEXT_BASE is not yet writable while we
still want to parse the image headers in some local onchip memory to
ie. extract firmware from that image.
Add the possibility to override the location where the headers get
loaded by introducing new function, spl_get_load_buffer() which takes
two arguments -- offset from the CONFIG_SYS_TEXT_BASE and size of the
data that are to be loaded there -- and returns a valid buffer address
or hangs the system. The default behavior is the same as before, add
the offset to CONFIG_SYS_TEXT_BASE and return that address. User can
override the weak spl_get_load_buffer() function though.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Enable USB gadget support using DWC2 driver
Populate board_usb_init() to initialize clocks,
phy, reset and data needed for DWC2 IP.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable config USB relative flags in order to enable USB
EHCI, DWC2 gadget, download and mass_storage support.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Create the handle of loaded images and the EFI_LOADED_IMAGE_PROTOCOL
inside efi_setup_loaded_image(). Do not use local variables.
Currently we expect the loaded image handle to point to the loaded image
protocol. Additionally we have appended private fields to the protocol.
With the patch the handle points to a loaded image object and the private
fields are added here. This matches how we handle the net and the gop
object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Virtual machine provided by qemu-arm has a ARM PL031 Real Time Clock
device. With this patch, the driver is enabled by default.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With this patch, PL031 driver is converted to driver-model-compliant
driver. In addition, CONFIG_SYS_RTC_PL031_BASE is no longer valid.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running in EL3 mode on AArch64, we have to first drop to EL2
to execute a UEFI payload. When dropping down, the arguments to
the entry point have to stay identical to the ones for normal entry
though.
In commit ea54ad5928 ("efi_loader: pass handle of loaded image")
we incorrectly changed that logic and had the el3 entry path diverge.
Fix it up by syncing it back to what it's supposed to be.
Fixes: ea54ad5928 ("efi_loader: pass handle of loaded image")
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The EFI selftest does not succeed on Sandbox yet. The network support
seems to need some love to actually make our current tests succeed.
So let's disable running the selftest on sandbox for now until "make
tests" just works. Then we can have more amazing CI than ever.
Signed-off-by: Alexander Graf <agraf@suse.de>
Since GRUB patch d0c070179d4d ("arm/efi: Switch to arm64 linux loader",
2018-07-09) we do not need a workaround for GRUB on 32bit ARM anymore.
So let's eliminate function efi_exit_caches().
This will require Linux distributions to update grub-efi-arm to the GRUB
git HEAD (a tag containing the aforementioned GRUB patch is not available
yet).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
CSI H can be used to position the cursor. The calling application may
specify a location that is beyond the limits of the screen. This may
lead to an illegal memory access.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
ascii2unicode() always ends the u16 string with '\0'.
Remove redundant assignment.
Add description for efi_str_to_u16() and ascii2unicode().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we assign a lot of protocols to loaded images though
these protocols are not related to them. Instead they should be
installed on a separate handle. Via the device path it is the
parent to the devices like the network adapter.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In efi_get_variable() a string is longer than the allocated space which
results in overwriting the linked list of malloc().
The prefixes used for variables are 41 characters long, e.g.
efi_67029eb5-0af2-f6b1-da53-fcb566dd1ce6_
Change PREFIX_LEN to 41.
Fixes: faff21556748 ("efi_loader: remove limit on variable length")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should run the EFI selftest on both a 32bit and a 64bit ARM platform on
Travis to catch possible errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Convert the function descriptions to Sphinx style.
efi_driver_init() is cCalled by efi_init_obj_list().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Not all terminals understand CSI [18t for querying the console size.
We should adhere to escape sequences documented in the console_codes
manpage and the ECMA-48 standard.
So here we follow a different approach. We position the cursor to the
bottom right and query its position. Before leaving the function we
restore the original cursor position.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently do not combine memory entries that are adjacent and have
the same attributes. The problem with that is that our memory map can
easily grow multiple hundreds of entries in a simple UEFI Shell
environment.
So let's make sure we always combine all entries to make the memory
map as small as possible. That way every other piece of code that
loops through it should also gain some nice speed ups.
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_set_bootdev() may be called repeatedly.
Free the memory allocated for device paths in previous calls.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Do not use a local variable for the handle backing the memory device path.
Adjust relate comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
gcc 4.8.4 wants to see all levels of braces when initializing a
structure to zeros.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should not check parameter file twice.
We should check parameter new_handle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With efi_loader, we may want to execute payloads from RAM. By default,
permissions on the RAM region don't allow us to execute from there though.
So let's change the default allocation scheme for RAM to also allow
execution from it. That way payloads that live in U-Boot RAM can be
directly executed.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In sandbox, longjmp returns to itself in an endless loop because
os_longjmp() calls into longjmp() which is provided by U-Boot which
again calls os_longjmp().
Setjmp on the other hand must not return because otherwise the
return freees up stack elements that we need during longjmp().
The only straight forward fix that doesn't involve nasty hacks I
could find is to directly link against the system setjmp/longjmp
implementations. That means we just provide the compiler with
hints that the symbol will be available and actually fill them
out with versions from libc.
This approach should be reasonably platform agnostic
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
For the VT102 and the Linux console the left upper corner is [1, 1].
EFI uses [0, 0] as left upper corner.
Check parameters of the SetCursorPosition() service.
Use CSI H like EDK2 for positioning.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_file_getinfo() is called with a GUID. In EFI_ENTRY use %pUl as
format type. This way the GUID is printed in debug mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should not directly cast between pointers and addresses since it breaks
sandbox. Fix this and simplify the code in file_read().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present map_sysmem() maps an address into the sandbox RAM buffer,
return a pointer, while map_to_sysmem() goes the other way.
The mapping is currently just 1:1 since a case was not found where a more
flexible mapping was needed. PCI does have a separate and more complex
mapping, but uses its own mechanism.
However this arrange cannot handle one important case, which is where a
test declares a stack variable and passes a pointer to it into a U-Boot
function which uses map_to_sysmem() to turn it into a address. Since the
pointer is not inside emulated DRAM, this will fail.
Add a mapping feature which can handle any such pointer, mapping it to a
simple tag value which can be passed around in U-Boot as an address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This function is useful to signal that the application needs to exit
immediate. It can be caught with a debugger (e.g. gdb). Add a stub for it
so that it can be called from within sandbox when an internal error
occurs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present the sandbox RAM buffer is not aligned to any particular
address boundary. This makes the internal pointers somewhat random with
respect to the associated RAM buffer addresses.
Align the buffer to the page size of the machine to help with this. Note
that there is a header at the start of the allocated pointer. To avoid
returning a pointer which is not aligned to a page boundary, we waste
almost an entire page of memory for each allocation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This allows this feature to build within sandbox. This is useful for
testing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
With sandbox these values depend on the host system. Let's assume that it
is x86_64 for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec requires that attributes are only set for when
EFI_FILE_MODE_CREATE is set in open_mode.
The SCT tries to read a directory with EFI_FILE_DIRECTORY.
As EDK2 allows this we should not be more strict.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The FAT driver supports unaligned reads and writes and EFI applications
will make use of these. So a misaligned buffer is only worth a debug
message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Unset CONFIG_EFI_UNICODE_CAPITALIZATION on boards with tough size
restrictions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use a key notification function to leave the
EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement registering and unregistreing key notify functions in the
EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a unit test for the EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a unit test for the EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Support modifiers for F1 - F4.
Add support for letters with ALT key.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch implements the EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL.
The implementation of notification functions is postponed to a later
patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should test the WaitForKey event.
Testing for EFI_NOT_READY can be done after resetting the console.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Preread the next key in the console timer event.
The EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL requires to trigger registered key
notification functions based on the prefetched key.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Move reusable utility functions to efi_selftest_util.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Test that the Euro sign is correctly retrieved from the console via the
EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Up to now the EFI_TEXT_INPUT_PROTOCOL only supported ASCII characters.
With the patch it can consume UTF-8 from the console.
Currently only the serial console and the console can deliver UTF-8.
Local consoles are restricted to ASCII.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this commit, test cases for unlink interfaces are added as part of
"test_fs" test suite.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this commit, test cases for mkdir interfaces are added as part of
"test_fs" test suite.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this commit and the following, test scripts for new filesystem
functionalities introduced by my patch set, "fs: fat: extend FAT write
operations," are provided.
In particular, this patch adds test cases for sub-directory write
and write with non-zero offset.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this commit, the same set of test cases as in test/fs/fs-test.sh
is provided using pytest framework.
Actually, fs-test.sh provides three variants:"sb" (sb command), "nonfs"
(fatxx and etc.) and "fs" (hostfs), and this patch currently supports
only "nonfs" variant; So it is not a replacement of fs-test.sh for now.
Simple usage:
$ py.test test/py/tests/test_fs [<other options>]
You may also specify filesystem types to be tested:
$ py.test test/py/tests/test_fs --fs-type fat32 [<other options>]
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
As far as this patch series has been applied, all the tests should
pass. So update the test result summary.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
'Delete' will be implemented here by calling fs_unlink() which relies on
underlying file system's implementation.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, a new command, fatrm, is added so as to delete a file
or directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, unlink support is added to FAT file system.
A directory can be deleted only if it is empty.
In this implementation, only a directory entry for a short file name
will be removed. So entries for a long file name can and should be
reclaimed with fsck.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"unlink" interface is added to file operations.
This is a preparatory change as unlink support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In efi world, there is no obvious "mkdir" interface, instead, Open()
with EFI_FILE_MODE_CREATE in mode parameter and EFI_FILE_DIRECTORY
in attributes parameter creates a directory.
In this patch, efi_file_open() is extended so as to accept such
a combination of parameters and call u-boot's mkdir interface for
expected action.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, a new command, fatmkdir, is added.
Please note that, as there is no notion of "current directory" on u-boot,
a directory name specified must contains an absolute directory path as
a parent directory. Otherwise, "/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, mkdir support is added to FAT file system.
A newly created directory contains only "." and ".." entries.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The starting cluster number of directory is needed to initialize ".."
(parent directory) entry when creating a new directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"mkdir" interface is added to file operations.
This is a preparatory change as mkdir support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, fatwrite command is extended so as to accept an additional
parameter of file offset.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, all the necessary code for allowing for a file offset
at write is implemented. What plays a major roll here is get_set_cluster(),
which, in contrast to its counterpart, set_cluster(), only operates on
already-allocated clusters, overwriting with data.
So, with a file offset specified, set_contents() seeks and writes data
with set_get_cluster() until the end of a file, and, once it reaches
there, continues writing with set_cluster() for the rest.
Please note that a file will be trimmed as a result of write operation if
write ends before reaching file's end. This is an intended behavior
in order to maintain compatibility with the current interface.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current write implementation is quite simple: remove existing clusters
and then allocating new ones and filling them with data. This, inevitably,
enforces always writing from the beginning of a file.
As the first step to lift this restriction, fat_file_write() and
set_contents() are modified to accept an additional parameter, file offset
and further re-factored so that, in the next patch, all the necessary code
will be put into set_contents().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, write implementation is overhauled and rewritten by
making full use of directory iterator. The obvious bonus is that we are
now able to write to a file with a directory path, like /A/B/C/FILE.
Please note that, as there is no notion of "current directory" on u-boot,
a file name specified must contain an absolute directory path. Otherwise,
"/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
It would be good that FAT write function return error code instead of
just returning -1 as fat_read_file() does.
This patch attempts to address this issue although it is 'best effort
(or estimate)' for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT file system's long file name support is a bit complicated and has some
restrictions on its naming. We should be careful about it especially for
write as it may easily end up with wrong file system.
normalize_longname() check for the rules and normalize a file name
if necessary. Please note, however, that this function is yet to be
extended to fully comply with the standard.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In my attempt to re-work write operation, it was revealed that iterator's
"clust" does not always point to a cluster to which a current directory
entry ("dent") belongs.
This patch assures that it is always true by adding "next_clust" which is
used solely for dereferencing a cluster chain.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT's root directory does not have "." nor ".."
So care must be taken when scanning root directory with fat_itr_resolve().
Without this patch, any file path starting with "." or ".." will not be
resolved at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
get_fs_info() was introduced in major re-work of read operation by Rob.
We want to reuse this function in write operation by extending it with
additional members in fsdata structure.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the missing SPDX-License-Identifier based on Linux kernel commit
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license").
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the missing SPDX-License-Identifier based on Linux kernel commit
b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to
files with no license").
Correct formatting errors.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
%s/efi_simple_input_interface/efi_simple_text_input_protocol/
We should be consistent in the naming of the EFI protocol interface
structures. The protocol is called EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
%s/ExtendedVerification/extended_verification/
Use consistent naming of function parameters. Do not use CamelCase.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Execute the EFI selftest for the EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a unit test for the EFI_UNICODE_COLLATION_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The patch implements the EFI_UNICODE_COLLATION_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide unit tests for utf_to_lower() utf_to_upper().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide functions for upper and lower case conversion.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides a define to initialize a table that maps lower to
capital letters for Unicode code point 0x0000 - 0xffff.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We register the console in/out protocol on the loaded image handle, but
never tell anyone about it in the systab.
Because of this Shell.efi can not find the input protocol. So let's add
a proper reference.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We have moved generating html documentation with Sphinx.
%s/Return Value/Return/g
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit ccfc78b820.
Now that the underlying issue is fixed, we can revert the revert and hence
restore the original EFI code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tegra U-Boot ensures that board_get_usable_ram_top() never returns a value
over 4GB, since some peripherals can't access such addresses. However, on
systems with more than 2GB of RAM, RAM bank 1 does describe this extra
RAM, so that Linux (or whatever OS) can use it, subject to DMA
limitations. Since board_get_usable_ram_top() points at the top of RAM
bank 0, the memory locations describes by RAM bank 1 are not mapped by
U-Boot's MMU configuration, and so cannot be used for anything.
For some completely inexplicable reason, U-Boot's EFI support ignores the
value returned by board_get_usable_ram_top(), and EFI memory allocation
routines will return values above U-Boot's RAM top. This causes U-Boot to
crash when it accesses that RAM, since it isn't mapped by the MMU. One
use-case where this happens is TFTP download of a file on Jetson TX1
(p2371-2180).
This change explicitly tells the EFI code that this extra RAM should not
be used, thus avoiding the crash.
A previous attempt to make EFI honor board_get_usable_ram_top() was
rejected. So, this patch will need to be replicated for any board that
implements board_get_usable_ram_top().
Fixes: aa909462d0 ("efi_loader: efi_allocate_pages is too restrictive")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use CONFIG_IS_ENABLED(EFI_LOADER) to avoid explicitly checking CONFIG_SPL
too. This simplifies the conditional.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The number of bytes in an utf-8 string is an upper limit for the number of
words in the equivalent utf-16 string. In so far the inumbant coding works
correctly. For non-ASCII characters the utf-16 string is shorter. With the
patch only the necessary buffer size is allocated for the load options.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The length of a string printed to the console by the
EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL is not limited by the UEFI spec.
Hence should not allocate a buffer for it on the stack.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI spec does not provide a length limit for variables.
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The width and precision of the printf() function refer to the number of
characters not to the number of bytes printed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
utf8_get() - get next UTF-8 code point from buffer
utf8_put() - write UTF-8 code point to buffer
utf8_utf16_strnlen() - length of a utf-8 string after conversion to utf-16
utf8_utf16_strncpy() - copy a utf-8 string to utf-16
utf16_get() - get next UTF-16 code point from buffer
utf16_put() - write UTF-16 code point to buffer
utf16_strnlen() - number of codes points in a utf-16 string
utf16_utf8_strnlen() - length of a utf-16 string after conversion to utf-8
utf16_utf8_strncpy() - copy a utf-16 string to utf-8
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function names utf16_strlen() and utf16_strnlen() are misnomers.
The functions do not count utf-16 characters but non-zero words.
So let's rename them to u16_strlen and u16_strnlen().
In utf16_dup() avoid assignment in if clause.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Using CONFIG_IS_ENABLED(EFI_LOADER) allows to simply the #if statements.
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Using CONFIG_IS_ENABLED(EFI_LOADER) allows to simply the #if statements.
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The fs_read() function wants to get an address rather than the
pointer to a buffer.
So let's convert the passed buffer from pointer back a the address
to make efi_loader on sandbox happier.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present this function takes a pointer as its argument, then passes this
to efi_allocate_pages(), which actually takes an address. It uses casts,
which are not supported on sandbox.
Also the function calculates the FDT size rounded up to the neared EFI
page size, then its caller recalculates the size and adds a bit more to
it.
This function is much better written as something that works with
addresses only, and returns both the address and the size of the relocated
FDT.
Also, copy_fdt() returns NULL on error, but really should propagate the
error from efi_allocate_pages(). To do this it needs to return an
efi_status_t, not a void *.
Update the code in this way, so that it is easier to follow, and also
supports sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Sandbox only has 128MB of memory so we cannot relocate the device tree up
to start at 128MB. Use 127MB instead, which should be safe.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Verify that the loaded image protocol is installed on the image handle.
Verify that the loaded image protocol points to the system table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The system table must be passed as a pointer in the loaded image
protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove memory leak in efi_selftest_manageprotocols.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds the clock-frequency property to the SPI controller
DT node. It will be used by the SPI driver to calculate the baud rate.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds the necessary sysreset DT node and enables the required
drivers via Kconfig.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The Gardena Smart-Gateway boards have a MT7688 SoC with 128 MiB of RAM
and 8 MiB of flash (SPI NOR) and additional 128MiB SPI NAND storage.
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The LinkIt Smart 7688 modules have a MT7688 SoC with 128 MiB of RAM
and 32 MiB of flash (SPI NOR).
This patch also includes 2 targets. One is the target that can be
programmed into the SPI NOR flash and a 2nd target "xxx-ram" is
added to support loading and booting via an already running U-Boot
version. This allows easy development and testing without the
need to flash the image each time.
Signed-off-by: Stefan Roese <sr@denx.de>
[fixed and regenerated defconfig files]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds basic support for the MediaTek MT7620/88 SoCs. Parts of
the code is copied from the MediaTek GitHub repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
The mt7628a.dtsi file is imported from Linux v4.17.
Support for the LinkIt Smart 7688 module and the Gardena Smart Gateway
both based on the MT7688 will be added in further patches.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for the UBIFS support. The file is a copy of
arch/xtensa/include/asm/atomic.h
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Caches should be configured to mode CONF_CM_CACHABLE_NONCOHERENT
(or CONF_CM_CACHABLE_COW when a CM is available). There is no
need to make this configurable.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The index base address used for the cache initialisation is currently
hard-coded to CKSEG0. Make this value configurable if a MIPS system
needs to have a different address (e.g. in SRAM or ScratchPad RAM).
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Changing the Cache Coherency Algorithm (CCA) for kernel mode
requires executing from KSEG1. Thus do a jump from KSEG0 to KSEG1
before changing the CCA mode. Jump back to KSEG0 afterwards.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Those functions are not needed during cache init and can be
implemented in C. Only support the safe disabling of caches when
this is required for booting an OS. Reenabling caches is much
harder to implement if an optional coherency manager must be
supported. As there is no real use-case anyway, dcache_enable
is implemented with an error message.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Some MIPS systems store some board-specific boot configuration
in the U-Boot binary at offset 0x10. This is used by Malta boards
and by Lantiq/Intel SoC's when booting from parallel NOR flash.
Convert the hard-coded values to Kconfig options to remove such
board-specific stuff out of the generic start.S code. This also
deprecates the config option CONFIG_SYS_XWAY_EBU_BOOTCFG.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
All U-Boot users must define the mtdparts environment variable with:
setenv mtdparts mtdparts=...
While this may ease the partition declaration job to be passed to
Linux, this is a pure software limitation and forcing this prefix is a
complete non-sense. Let the user to declare manually the mtdparts
variable without the prefix.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Let spi-nand devices be recognized by mtdparts. This is superfluous
but a full mtdparts rework would be very time-consuming.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
While 1kB or 1kiB will be parsed correctly, 1k will return the right
amount, but the metric suffix will not be escaped once the char
pointer updated. Fix this situation by simplifying the move of the
endp pointer.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Both ustrtoul and ustrtoull interpret 1k but not 1m or 1g. Even if the
SI symbols for Mega and Giga are 'M' and 'G', certain entries of
eg. mtdparts also use (wrongly) the metric prefix 'm' and 'g'.
I do not see how parsing lowercase prefixes could break anything, so
parse them like their uppercase counterpart.
Also, even though kiB is not equal to kB in general, lets not change
U-Boot behavior and always use kiB and kB (same applies for MiB vs. MB
and GiB vs. GB) as a representation for 1024 instead of 1000.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Switch blocks for deriving size naturally use fallthrough between
'case' statements. Make it explicit.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
These definitions are simply not used and are misleading because similar
definitions exist in jffs2/load_kernel.h and are used widely to define
MTD device types (which is, by the way, totally redundant with what the
MTD core does). Remove these definitions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Balance debug message in the partition allocation/removal process in
order to keep track of them more easily.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
UBI selects MTD_PARTITIONS which is the symbol to compile
drivers/mtd/mtdpart.c. Unfortunately, the symbol was not defined in
Kconfig and this worked only with board files defining it. Fix this by
adding a boolean in Kconfig so boards defined by defconfig files only
will work as expected.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add support for the MX35LF2GE4AB chip, which is similar to its cousin
MX35LF1GE4AB, with two planes instead of one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Add a SPI NAND framework based on the generic NAND framework and the
spi-mem infrastructure.
In its current state, this framework supports the following features:
- single/dual/quad IO modes
- on-die ECC
Signed-off-by: Peter Pan <peterpandong@micron.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Some controllers are exposing high-level interfaces to access various
kind of SPI memories. Unfortunately they do not fit in the current
spi_controller model and usually have drivers placed in
drivers/mtd/spi-nor which are only supporting SPI NORs and not SPI
memories in general.
This is an attempt at defining a SPI memory interface which works for
all kinds of SPI memories (NORs, NANDs, SRAMs).
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The NAND sub-layers are likely to need the MTD_OPS_XXX mode information
in order to decide if they should enable/disable ECC or how they should
place the OOB bytes in the provided OOB buffer.
Add a field to nand_page_io_req to pass this information.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Add an intermediate layer to abstract NAND device interface so that
some logic can be shared between SPI NANDs, parallel/raw NANDs,
OneNANDs, ...
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
There is no reason to have NAND, SPI flashes and UBI sections outside of
the MTD submenu in Kconfig.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
We are going to begin using the mtd->dev.of_node field for MTD device
nodes, so let's add helpers for it. Also, we'll be making some
conversions on spi_nor (and nand_chip eventually) too, so get that ready
with their own helpers.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Some MTD sublayers/drivers are implementing ->_read/write() and
not ->_read/write_oob().
While for NAND devices both are usually valid, for NOR devices, using
the _oob variant has no real meaning. But, as the MTD layer is supposed
to hide as much as possible the flash complexity to the user, there is
no reason to error out while it is just a matter of rewritting things
internally.
Add a fallback on mtd->_read() (resp. mtd->_write()) when the user calls
mtd_read_oob() (resp. mtd_write_oob()) while mtd->_read_oob() (resp.
mtd->_write_oob) is not implemented. There is already a fallback on the
_oob variant if the former is used.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Unlike what's done in mtd_read/write(), there are no checks to make sure
the parameters passed to mtd_read/write_oob() are consistent, which
forces implementers of ->_read/write_oob() to do it, which in turn leads
to code duplication and possibly errors in the logic.
Do general sanity checks, like ops fields consistency and range checking.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Peter Pan <peterpandong@micron.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
[Miquel: squashed the fix about the chip's size check]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
The Clearfog SOM can optionally have eMMC installed. Enable support for
eMMC boot partitions by default.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support to Armada 7k/8k comphy RX/TX lane swap. The
'phy-invert' DT property defines the inverted signals.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add definitions for CONFIG_ENV_SPI_BUS and CONFIG_ENV_SPI_CS
to Armada-388-GP board configuration
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason the spi_flash_probe_bus_cs() is called
inside the setup_flash_device() with zero values in place
of configurated SPI flash mode and maximum flash speed.
This code causes HALT error during startup environment
relocation on some platforms - namely Armada-38x-GP board.
Fix the function call by replacing zeros with the appropriate
values - CONFIG_ENV_SPI_MAX_HZ and CONFIG_ENV_SPI_MODE.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add comments with timing parameter names and some details about
nand layout fileds.
Remove unneeded definition.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Replace the hardcoded value of page chink with value that
depends on flash page size and ECC strength.
This fixes nand access errors for 2K page flashes with 8-bit ECC.
Move the initial flash commannd function assignment past the ECC
structures initialization for eliminating usage of hardcoded page
chunk size value.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
In the current driver, OOB bytes are accessed in raw mode, and when a
page access is done with NDCR_SPARE_EN set and NDCR_ECC_EN cleared, the
driver must read the whole spare area (64 bytes in case of a 2k page,
16 bytes for a 512 page). The driver was only reading the free OOB
bytes, which was leaving some unread data in the FIFO and was somehow
leading to a timeout.
We could patch the driver to read ->spare_size + ->ecc_size instead of
just ->spare_size when READOOB is requested, but we'd better make
in-band and OOB accesses consistent.
Since the driver is always accessing in-band data in non-raw mode (with
the ECC engine enabled), we should also access OOB data in this mode.
That's particularly useful when using the BCH engine because in this
mode the free OOB bytes are also ECC protected.
Fixes: 43bcfd2bb24a ("mtd: nand: pxa3xx: Add driver-specific ECC BCH support")
Cc: stable@vger.kernel.org
Reported-by: Sean Nyekjær <sean.nyekjaer@prevas.dk>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is needed to properly support the 8-bits ECC configuration
with 4KB pages.
When pages larger than 2 KB are used on platforms using the PXA3xx
NAND controller, the reading/programming operations need to be split
in chunks of 2 KBs or less because the controller FIFO is limited to
about 2 KB (i.e a bit more than 2 KB to accommodate OOB data). Due to
this requirement, the data layout on NAND is a bit strange, with ECC
interleaved with data, at the end of each chunk.
When a 4-bits ECC configuration is used with 4 KB pages, the physical
data layout on the NAND looks like this:
| 2048 data | 32 spare | 30 ECC | 2048 data | 32 spare | 30 ECC |
So the data chunks have an equal size, 2080 bytes for each chunk,
which the driver supports properly.
When a 8-bits ECC configuration is used with 4KB pages, the physical
data layout on the NAND looks like this:
| 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 1024 data | 30 ECC | 64 spare | 30 ECC |
So, the spare area is stored in its own chunk, which has a different
size than the other chunks. Since OOB is not used by UBIFS, the initial
implementation of the driver has chosen to not support reading this
additional "spare" chunk of data.
Unfortunately, Marvell has chosen to store the BBT signature in the
OOB area. Therefore, if the driver doesn't read this spare area, Linux
has no way of finding the BBT. It thinks there is no BBT, and rewrites
one, which U-Boot does not recognize, causing compatibility problems
between the bootloader and the kernel in terms of NAND usage.
To fix this, this commit implements the support for reading a partial
last chunk. This support is currently only useful for the case of 8
bits ECC with 4 KB pages, but it will be useful in the future to
enable other configurations such as 12 bits and 16 bits ECC with 4 KB
pages, or 8 bits ECC with 8 KB pages, etc. All those configurations
have a "last" chunk that doesn't have the same size as the other
chunks.
In order to implement reading of the last chunk, this commit:
- Adds a number of new fields to the pxa3xx_nand_info to describe how
many full chunks and how many chunks we have, the size of full
chunks and partial chunks, both in terms of data area and spare
area.
- Fills in the step_chunk_size and step_spare_size variables to
describe how much data and spare should be read/written for the
current read/program step.
- Reworks the state machine to accommodate doing the additional read
or program step when a last partial chunk is used.
This commit is taken from Linux:
'commit c2cdace755b'
("mtd: nand: pxa3xx_nand: add support for partial chunks")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit simplifies the initial configuration performed
by pxa3xx_nand_scan. No functionality change is intended.
This commit is taken from Linux:
'commit 154f50fbde53'
("mtd: pxa3xx_nand: Simplify pxa3xx_nand_scan")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The Data Flash Control Register (NDCR) contains two types
of parameters: those that are needed for device identification,
and those that can only be set after device identification.
Therefore, the driver can't set them all at once and instead
needs to configure the first group before nand_scan_ident()
and the second group later.
Let's split pxa3xx_nand_config in two halves, and set the
parameters that depend on the device geometry once this is known.
This commit is taken from Linux:
'commit 66e8e47eae65'
("mtd: pxa3xx_nand: Fix initial controller configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The chunk size represents the size of the data chunks, which
is used by the controllers that allow to split transferred data.
However, the initial chunk size is used in a non-split way,
during device identification. Therefore, it must be large enough
for all the NAND commands issued during device identification.
This includes NAND_CMD_PARAM which was recently changed to
transfer up to 2048 bytes (for the redundant parameter pages).
Thus, the initial chunk size should be 2048 as well.
On Armada 370/XP platforms (NFCv2) booted without the keep-config
devicetree property, this commit fixes a timeout on the NAND_CMD_PARAM
command:
[..]
pxa3xx-nand f10d0000.nand: This platform can't do DMA on this device
pxa3xx-nand f10d0000.nand: Wait time out!!!
nand: device found, Manufacturer ID: 0x2c, Chip ID: 0x38
nand: Micron MT29F8G08ABABAWP
nand: 1024 MiB, SLC, erase size: 512 KiB, page size: 4096, OOB size: 224
This commit is taken from Linux:
'commit c7f00c29aa8'
("mtd: pxa3xx_nand: Increase the initial chunk size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The read ID count should be made as large as the maximum READ_ID size,
so there's no need to have dynamic size. This commit sets the hardware
maximum read ID count, which should be more than enough on all cases.
Also, we get rid of the read_id_bytes, and use a macro instead.
This commit is taken from Linux:
'commit b226eca2088'
("nand: pxa3xx: Increase READ_ID buffer and make the size static")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When 2 commands are submitted in a row, and the second is very quick,
the completion of the second command might never come. This happens
especially if the second command is quick, such as a status read
after an erase
This patch is taken from Linux:
'commit 21fc0ef9652f'
("mtd: nand: pxa3xx-nand: fix random command timeouts")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
When the nand is first probe, and upon the first command start, the
status bits should be cleared before the interrupts are unmasked.
This commit is taken from Linux:
'commit 0b14392db2e'
("mtd: nand: pxa3xx_nand: fix early spurious interrupt")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the pxa3xx_nand driver was added there has been a discrepancy in
pxa3xx_nand_set_sdr_timing() around the setting of tWP_min and tRP_min.
This brings us into line with the current Linux code.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Don't store struct mtd_info in struct pxa3xx_nand_host. Instead use the
one that is already part of struct nand_chip. This brings us in line
with current U-boot and Linux conventions.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The initial buffer is used for the initial commands used to detect
a flash device (STATUS, READID and PARAM).
ONFI param page is 256 bytes, and there are three redundant copies
to be read. JEDEC param page is 512 bytes, and there are also three
redundant copies to be read. Hence this buffer should be at least
512 x 3. This commits rounds the buffer size to 2048.
This commit is taken from Linux:
'commit c16340973fcb64614' ("nand: pxa3xx: Increase initial buffer size")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Ofer Heifetz <oferh@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
If PCIe Mox module is connected we want to have PCIe node enabled
in U-Boot's device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove smi_pins definition since it is already in armada-37xx.dtsi.
Add assigned-clocks definitions to spi0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the pci-aardvark driver in defconfig for Turris Mox and also
enable the pci command.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro name CONFIG_WDT_ARMADA_3720 is called CONFIG_WDT_ARMADA_37XX
instead. Fix this so that watchdog really is enabled in board_init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for changing clock rate and parent clock for Armada 37xx
peripheral clocks.
Only clocks which can be disabled (.can_gate is true) can have parent
or rate changed.
This is needed so that Turris Mox can change SPI clock in device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds a weak definition of comphy_update_map to comphy_core,
which does nothing. If this function is defined elsewhere, for example
in board file, the board file can change some parameters of SERDES
configuration.
This is needed on Turris Mox, where the SERDES speed on lane 1 has to
be set differently when SFP module is connected and when Topaz Switch
module is connected.
This is a temporary solution. When the comphy driver for armada-3720
will be added to the kernel, the comphy driver in u-boot shall also be
updated and this should be done differently then.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The bootROM in the Armada-38x (and similar) SoC has two modes for UART
boot. The first is when the normal boot media is blank (or otherwise
missing the kwb header). The second is when the boot sequence has been
interrupted with the magic byte sequence on the UART lines.
In the first mode the bootROM routine and error code register will
indicate that there was an error booting from the configured media in
bits 7:0. In the second mode there is no error to indicate but the boot
source is provided via bits 31:28.
Handle both situations so that kwboot can be used for both boot
strapping a blank board and for intercepting a regular boot sequence.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This reverts commit e83e2b3900. This
prevents kwboot from overriding the hardware strapped boot source.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Detect the SD/eMMC boot device at run-time. Load the environment from
the boot deice, as well as save to it.
Leave the environment offset the same as in the SPI flash.
Make SD/eMMC 0 the default environment device when the boot device is
not detected.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch accomplishes 2 things to make the kwboot procedure
on the a38x more reliable.
1) We fill the tty with 1K of the magic bootparam. This helps
with the timing of where the microcode picks up in the read of
the line to ensure we actually catch the break to go into recovery
mode
2) Before starting the xmodem transfer we sleep for 2 seconds
and then flush the line. This allows all the magic bootparam
to be flushed from the line and makes the xmodem transfer reliable
and removes the Bad message failures.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Stefan is listed as a kirkwood maintainer since commit f822d8578b
(MAINTAINERS: Update Marvell custodianship).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The default bootdelay of 3 seconds is good enough and there is no need
to duplicate it in CONFIG_EXTRA_ENV_SETTINGS.
Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The comment of child_pre_probe, one of the 'struct uclass_driver'
members, is currently missing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, "help dm" shows as follows:
=> help dm
dm - Driver model low level access
Usage:
dm tree Dump driver model tree ('*' = activated)
dm uclass Dump list of instances for each uclass
dm devres Dump list of device resources for each device
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This adds a new defconfig which pre-selects the PICO-Hobbit baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds a new defconfig which pre-selects the PICO-Pi baseboard
allowing a completely non-interactive boot process.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Adds ofnode_by_prop_value() to search for nodes with a given property
and value, an ofnode version of fdt_node_offset_by_prop_value().
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 30a90f56c3 ("dm: core: add functions to get memory-mapped I/O
addresses") introduced a devfdt_remap_addr_index() routine but it does
not make use of the index parameter.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
All Linux firmware drivers are put under "/firmware" node
and it has support to populate "/firmware" node by default.
u-boot and Linux can share same DTB. In this case, driver
probe for devices under "/firmware" will not be invoked
as "/firmware" does not have its own "compatible" property.
This patch scans "/firmware" node by default like "/clocks".
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create separate function for scanning node by path and
move "/clock" node scan code into that function.
This will be usable if scanning of more node is required.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a driver to configure the SerDes (Serializer/Deserializer) lanes on
the MPC83xx architecture.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
When the DM CPU drivers are active, printing information about a CPU
should be delegated to a matching driver.
Hence, add a static print_cpuinfo that implements this delegation when
DM CPU drivers are active.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Changed condition to CONFIG_IS_ENABLED(CPU):
Signed-off-by: Simon Glass <sjg@chromium.org>
To print the reset status during boot, add a method print_resetinfo to
board_f, which is called in init_sequence_f[], that gets the reset
information from the sysreset driver (assuming there is only one seems
reasonable), and prints it.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
It's useful to have the reset status of the SoC printed out during reset
(e.g. to learn whether the reset was caused by software or a watchdog).
As a first step to implement this, add a get_status method to the
sysreset class, which enables the caller to get printable information
about the reset status (akin to get_desc in the CPU uclass).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Sandbox is not a real bootloader and it does require
a position independent code to be supported.
Thus, build it with -fPIC explicitly.
Fixes: 16940f720f9b ("Makefile: Don't generate position independent code")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reported-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Now that we have the pinctrl driver for Merrifield in place we can make
use of it and set I2C#6 pins appropriately.
Initial configuration came from the firmware. Which quite likely has
been used in the phones, where that is not part of Atom peripheral, is
in use. Thus we need to override the leftover.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This API is going to be used to configure some pins that are protected
for simple modification.
It's not a comprehensive pinctrl driver but can be turned into one
when we need this in the future. Now it is planned to be used only
in one place. So that's why I decided not to pollute the codebase with a
full-blown pinctrl-merrifield nobody will use.
This driver reads corresponding fields in DT and configures pins
accordingly.
The "protected" flag is used to distinguish configuration of SCU-owned
pins from the ordinary ones.
The code has been adapted from Linux work done by Andy Shevchenko
in pinctrl-merrfifield.c
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fix build warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This interface will be used to configure properly some pins on
Merrifield that are shared with SCU.
scu_ipc_raw_command() writes SPTR and DPTR registers before sending
a command to SCU.
This code has been ported from Linux work done by Andy Shevchenko.
Signed-off-by: Georgii Staroselskii <georgii.staroselskii@emlid.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On a
u32 val = __sw32(*addr);
multiple memory accesses are not welcome, since "addr" may
be an IO peripheral register address.
This patch changes __sw16/32 to perform a single memory
access for the source value.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
The Gen2 TMU is fed with fixed 32.5 MHz signal from CP .
This is then divided by 4 in TMU. Fix the timer clock
setting in Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Replace those two functions with generic ones by defining the
timer macros in include/config/*.h .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The code uses all in all three TMU registers, drop the massive
register layout structures and just define the required timer
registers and use them throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The header contains only the TMU register layout, just inline it
into the TMU timer implementation and drop the header completely.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The R-Car Gen2 feeds the TMU with CONFIG_SYS_CLK_FREQ / 2,
while the old SH parts use CONFIG_SYS_CLK_FREQ directly.
Just put this into the TMU implementation and drop the
CONFIG_SH_TMU_CLK_FREQ config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
These functions are always called for timer = 0, so drop the
timer check. Since these functions are called from one place
only and they are reduced to one line of code, just inline
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The tmu_bit value evaluates to (ffs(4) >> 1) - 1 = (3 >> 1) - 1 = 0.
Just drop the tmu_bit completely as well as CONFIG_SYS_TMU_CLK_DIV.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
This constant is always 4 , for all boards that exist. Define it
once in arch/sh/lib/time.c and remove it from the configs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add vbus-supply regulator support.
On some board vbus is not controlled by the phy but by
an external regulator.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The dtb should be embedded in the u-boot-spl image so that
the CONFIG_SPL_TARGET of spl/u-boot-spl.hex includes it.
This also affects the main u-boot image, so adjust
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME to u-boot.img which now
also includes the dtb.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Incorrect type of size variable results in 0 being
returned for sdram sizes greater than or equal to
4GB.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Stratix10 combines the u-boot-spl image into the fpga configuration
bitstream so that the SDM can load the processors memory. This
process requires a hex format of the u-boot-spl image.
CONFIG_SPL_TARGET is set to "spl/u-boot-spl.hex"
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Some devices, namely Intel's stratix10 SoC, require u-boot-spl in
a hex format. This patch adds spl/u-boot-spl.hex as a possible
target.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Add code to reset all reset signals as in gpio DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Enabled get_function support for dwapb where the function will
return the state of GPIO port.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Falcon mode allows the SPL to load and jump directly to the kernel,
without loading U-Boot proper.
Add detailed step by step on how to use Falcon mode on pico-imx6ul.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx6ul does not have a GPIO for selecting Falcon versus normal
mode, enter in Falcon mode when the customer selects the
CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The serverip part is provided from DHCP server with
'option root-path "192.168.3.1:/srv/tftp/rootfs";' parameter in dhcpd.conf
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The quotes around ${bootargs} were missing as we elaborate those variables
twice - once when we "setenv" the command and secondly when we "run" it.
Without quotes we have just empty string in the second call.
Moreover there is an issue with line breaks - as the original commands
got truncated.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'dhcp' command is more versatile as it allows working with the DHCP
server to obtain serverip, ipaddress and other network parameters.
The configuration necessary to obtain the serverip (dhcpd.conf):
option option-150 code 150 = ip-address;
and in the subnet definition:
option option-150 192.168.X.Y;
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The 'rootpath' can be provided by DHCP server. Removing this line prevents
from overwriting it.
To do that on the DHCP server side (isc-dhcp-server) modify dhcpd.conf
and add 'option root-path "192.168.X.Y:/srv/tftp/rootfs";'
Signed-off-by: Lukasz Majewski <lukma@denx.de>
just try to bring up an imx6ull board with console
on uart5 and found, that input_val for pin
MX6UL_PAD_UART5_RX_DATA__UART5_DCE_RX is 7 and
not 5 on imx6ull.
With this patch rx works now.
Signed-off-by: Heiko Schocher <hs@denx.de>
The CONFIG_FSL_USDHC is defined inside "mx6_common.h", which is
already included in this file.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This rework the DFU settings so it supports the SPL and U-Boot image,
as well as the single partition layout we are using by default.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Due the changes in previous commits, we need to resync the defconfig
to reduce noise in next commits.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The 'bmode' command is helpful for switching the boot media.
In the case of pico-imx6ul there are two possible boot media:
eMMC or USB.
To boot from eMMC:
=> bmode emmc
To boot from USB (via Serial Download Protocol):
=> bmode usb
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx6ul U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc2-00130-g0881835-dirty
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx6ul to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
There are two versions of imx6ul pico SOMs: one with 256MB and another
one with 512MB of RAM.
Convert to SPL so that both versions can be supported. This patch
doesn't rework the clock initialization to avoid changing the behavior
in this same patch, so it will be cleaned up in future.
Currently only the 256MB is tested/supported.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of keeping a custom environment, use a more generic approach
by switching to distro config.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
I just stumbled over some cluttered UBIFS messages. It seems some
newline chars are missing in the current U-Boot UBI source.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Last user of this driver went away in May 2017, in
commit eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
When used with a device tree, this will extract the card detect
and write protect pins from the device tree and configure them
accordingly. This assumes the GPIO_ACTIVE_LOW/HIGH is supported
by da8xx_gpio.
Signed-off-by: Adam Ford <aford173@gmail.com>
DM_I2C_COMPAT is somehow being enabled outside of Kconfig, so
this explicitly undefines it in the header file, and brackets
the I2C initialization around an #ifdef to not manually
initialize the I2C controller when the DM_I2C is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
Enabling DM_PMIC, DM_REGULATOR_FIXED, and DM_REGULATOR_GPIO
gives us the ability to better monitor voltages and enable
hardware through the device tree. The TL4030 (TPS65950) is
not yet migrated to DM, so this patch only enables the fixed
and GPIO controlled regulators.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM enabled, this patch enables DM_SERIAL and removes
the NS16550 initialization from da850_lowlevel since the driver
will take care of that itself.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM_MMC now available, this patch enables DM_MMC for the
omapl138_lcdk in U-Boot and keeps the older style for SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
With CONFIG_BLK becoming a requirement, the Davinci MMC driver
needs to be updated with DM_MMC support. Since SPL is tiny and
many boards do not support DM in SPL, this retains the backwards
compatibility for those boards who need to initialize MMC manually
in SPL.
Signed-off-by: Peter Howard <phoward@gme.net.au>
Signed-off-by: Adam Ford <aford173@gmail.com>
The simple pinctrl driver currently available works with the omap3.
Enabling this will use the device tree to automatically set the
pin-muxing for various drivers.
Signed-off-by: Adam Ford <aford173@gmail.com>
The OF_CONTROL and OF_PLATDATA are not really useful without DM.
This patch supports DM_SPL, but it requires manual references
both Serial and MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
The getcd and getwp functions when DM_MMC is enabled are
assumming the DM_GPIO is enabled. In cases (like SPL) where
DM_GPIO may not be enabled, wrap these calls in an #ifdef
Signed-off-by: Adam Ford <aford173@gmail.com>
The serial port was being manually configured during SPL build,
however in preparation to allow DM in SPL, this needs to change
to be based on whether or not DM_SERIAL is enabled because, soon
the assumption that SPL means no DM may not be accurate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
boot-common.c checks to see if I2C is enabled in SPL, but
it doens't check for DM_I2C before initializing it. This
will now only initialize the I2C is the DM_I2C is not enabled
to avoid initializing it more than once.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platforms with limited resources in SPL may enable OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
Platforms with limited resources in SPL may enably OF_PLATDATA,
this limits some of the library functions and cannot extract data
from the device tree. This patch adds additional wrappers around
these functions to only allow them when OF_CONTROL is enabled and
OF_PLATDATA is not.
Signed-off-by: Adam Ford <aford173@gmail.com>
The driver was developed with references for more than just
dra7, but never included. At least for omap3, this appears
to be functional.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO bank numbers do not appear in the device tree, so this
patch makes the gpio name based on the address
(ie gpio@49054000_31 vs gpio4_31)
adam
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With the re-sync from Linux 4.18, several entries in
da850-evm-u-boot.dtsi are no longer necessary, so this patch
removes them.
Signed-off-by: Adam Ford <aford173@gmail.com>
With DM and device tree support, let's use the GPIO_ACTIVE_HIGH
and GPIO_ACTIVE_LOW from the device tree as they are intended.
Signed-off-by: Adam Ford <aford173@gmail.com>
The GPIO banks are broken up into two 16-bit registers for each
bank set. Unfortunately, the math that determines how to shift
blindly shifted by the number of the gpio. This worked for gpio
numbers under 32, but higher gpio's are broken. This fixes the
gpio index, so the bank is passed and the shift amount within
the register is passed now instead of the gpio number.
Fixes: 8e51c0f25406("dm: gpio: Add DM compatibility to
GPIO driver for Davinci")
Signed-off-by: Adam Ford <aford173@gmail.com>
The DA850-EVM supports booting from NAND when used with the
UI expander board. da850evm_nand will create an ais file
that can be burned to NAND and booted while storing the env in
NAND along with some partitions tables for storing kernel,
dtb and rootfs in NAND.
Signed-off-by: Adam Ford <aford173@gmail.com>
At least for now, CONFIG_BLK is working, but this variant of
the da850evm doesn't need/support SPL so it's OK to enable it
here.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add the minimum dt nodes required to boot. These nodes
will get deleted as kernel gets these nodes added in the
main dts files.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Create a basic U-Boot environment that allows the automatic loading
of a Linux Kernel located at /boot/Image and an associated device tree
blob located at /boot/k3-am654-base-board.dtb from the secondary
partition of an ext4-formatted SD card on the AM654x EVM. Furthermore
the boot.scr and uEnv.txt detection and loading schemes are supported
in a manner already known from other TI platforms.
Note that this is intended to be a starting point to enable initial
board use and will most certainly get extended and refactored as
different boot media become available.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for AM654 based EVM running on A53. Enable
4GB of DDR available on the EVM so that kernel DTB file
can be updated accordingly.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Andreas: Added 4GB ddr support]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
As no gpio.h is defined in arch/arm/mach-k3/include/,
to avoid compilation failure, do not include asm/arch/gpio.h.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 has an arasan sdhci controller and a mmc phy attached to it.
Add basic support for K3 specific arasan sdhci controller.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for K3 based remoteproc driver that
communicates with TISCI to start start a remote processor.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
K3 specific SoCs have a dedicated microcontroller for doing
resource management. Any HLOS/firmware on compute clusters should
load a firmware to this microcontroller before accessing any resource.
Adding support for loading this firmware.
After the K3 system controller got loaded with firmware and started
up it sends out a boot notification message through the secure proxy
facility using the TI SCI protocol. Intercept and receive this message
through the rproc start operation which will need to get invoked
explicitly after the firmware got loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Existing rproc_init() api tries to initialize all available
remoteproc devices. This will fail when there is dependency
among available remoteprocs. So introduce a separate api
that allows to initialize remoteprocs individually based
on id.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Sometimes mbox controllers wants to store private data in
mbox_chan so that it can be used at a later point of time.
Adding support for hooking private data.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Devices from the TI K3 family of SoCs like the AM654x contain a Device
Management and Security Controller (SYSFW) that manages the low-level
device control (like clocks, resets etc) for the various hardware
modules present on the SoC. These device control operations are provided
to the host processor OS through a communication protocol called the TI
System Control Interface (TI SCI) protocol.
This patch adds a system reset driver that communicates to the system
controller over the TI SCI protocol for allowing to perform a system-
wide SoC reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There are cases where there are more than one power domain
attached to the device inorder to get the device functional.
So add support for enabling power domain based on the index.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some systems require more than a single ID to identify and configure any
clock provider. For those scenarios add an optional data field to the
clock control structure.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management of
various devices present on the SoC. Various reset functionalities are
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/reset/reset-ti-sci.c driver of
the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some systems require more than a single ID to identify and configure any
reset provider. For those scenarios add an optional data field to the
reset control structure.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a reset operations function pointer to support querying the current
status of a reset control.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
To support scenarios where a firmware device node has subnodes that
have their own drivers automatically scan the DT and bind those when
the firmware device gets bound.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
TI-SCI message protocol provides support for controlling of various
physical cores available in SoC. In order to control which host is
capable of controlling a physical processor core, there is a processor
access control list that needs to be populated as part of the board
configuration data.
Introduce support for the set of TI-SCI message protocol apis that
provide us with this capability of controlling physical cores.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since system controller now has control over SoC power management, it
needs to be explicitly requested to reboot the SoC. Add support for
it.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Introduce the fundamental
device management capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
TI-SCI message protocol provides support for board configuration
to assign resources and other board related operations.
Introduce the board configuration capability support to the driver protocol
as part of this change.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Update Makefile to generate
- tispl.bin: First stage bootloader on ARMv8 core
- u-boot.img: Second stage bootloader on ARMv8 core.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a script that is capable of generating a FIT image
source file that combines ATF, SPL(64 bit) and DT.
This combined image is used by R5 SPL and start ATF
on ARMv8 core.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
By default the device control module registers are locked,
preventing any writes to its registers.
Unlock those registers as part of the init flow.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 allows for booting from primary or backup boot media.
Both media can be chosen individually based on switch settings.
ROM looks for a valid image in primary boot media, if not found
then looks in backup boot media. In order to pass this boot media
information to boot loader, ROM stores a value at a particular
address. Add support for reading this information and determining
the boot media correctly.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On K3 family SoCs, once the ROM loads image on R5, M3 resets R5 and
expects to start executing from 0x0. In order to handle this ROM
updates the boot vector of R5 such that first 64 bytes of image load
address are mapped to 0x0.
In this case, it is SPL's responsibility to jump to the proper image
location. So, update the PC with address of reset vector(like how
other exception vectors are handled), instead of branching to reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654 device is designed for industrial automation and PLC
controller class platforms among other applications. Introduce
base support for AM654 SoC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The MIO clock is enabled by default, and the STDMAC clock is
enabled by the clk driver. The ad-hoc way to enable the clock
is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that CONFIG_SYS_MONITOR_LEN increased, we have room for enabling
more options again.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the migration to distro-boot, the size of the U-Boot proper
image for uniphier_v7_defconfig exceeded the current limit, 576KB.
Increase it to 832KB.
CONFIG_SYS_UBOOT_BASE must be moved as well to avoid the image
over-wrap because the boot ROM of Pro4, Pro5, PXs2/LD6b loads
the SPL to the physical address 0x100000.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
FPGA subsystem requires special care that's why it should be maintained
via one tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are ways how to call fpga loadmk
1. Full command
fpga loadmk [dev] [address]
2. Dev setup via variable
set fpga [dev]
fpga loadmk [address]
3. Address setup via variable
set fpgadata [address]
fpga loadmk [dev]
4. Dev and address setup via variables
set fpga [dev]
set fpgadata [address]
fpga loadmk
Before this patch only cases 1 and 3 are working but the part of code
was trying to support also cases 2 and 4.
This patch is adding support for cases 2 and 4 to have all of
combinations supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert loadmk command to fpga subcommands. Not all combinations are
working but they have never worked properly. This will be fixed later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Separate dump, load, loadb, loadp and loadbp commands to separate
functions to make it clear how they are called and what parameters they
need.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga info to U_BOOT_CMD_MKENT subcommand.
Also use strtol instead of simple_strtoul. The reason is that if -1 is
passed (or fpga info without "fpga" variable) the list of all fpgas is
shown.
This functionality is in the fpga core but it couldn't be performed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Create command wrapper to clean fpga subcommands.
The function logic is taken from cmd_dm.c
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch. Check them
directly when they are read. Also there is no reason to check loadmk
case separately because fpga_data address must be non zero too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Parameter checking is dead code because all the time there must be all
params assigned. If they are not assigned there is no 9th parameters
passed and checking before return CMD_RET_USAGE.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to check parameters in separate switch before main
one. This patch is simplifying error path and checking parameters right
after assignment.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Incorrect command is already handled and FPGA_NONE should be used only
one. In case of error CMD_RET_USAGE can be returned directly without any
addition logic around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move fpga_get_op() to top of file to remove local function declaration
and also remove useless retyping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Clean fpga_get_op() error handling by moving checking/print to do_fpga.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for info, load, loadp, loadb, loadbp, loadmk_legacy,
loadmk_legacy_gz, loadmk_fit, loadfs also with variable support.
There are probably missing failed tests.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch applied in 2010
"cmd_fpga: cleanup help and check parameters"
(sha1: a790b5b2326be9d7c9ad9e3d9b51a8bfabc62d07"
was adding this checking
+ if (dev == FPGA_INVALID_DEVICE) {
+ puts("FPGA device not specified\n");
+ op = FPGA_NONE;
+ }
which simply broke one command flow which was
setenv fpga <dev>
fpga loadmk <addr> // legacy image
fpga loadmk <addr>:<fit_image_name> //fit image
Also this sequence for FIT image is completely broken
setenv fpga <dev>
setenv fpgadata <addr>:<fit_image_name>
fpga loadmk
(Note: For legacy images this is working fine).
even from code I don't think this has ever worked properly
for fit image (dev = FPGA_INVALID_DEVICE should be rejected
by fpga core). Fit image support was in 2008 added by:
"[new uImage] Add new uImage fromat support to fpga command"
(sha1: c28c4d193d)
Just a summary of these facts that none found this for pretty long time
it shouldn't be a problem to remove this flow (without fpga dev)
completely to simplify the code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are multiple GPIOs that can be used with the same driver depending
on the CONFIG_GPIO_BASE defined in the controller driver.
GPIO3 and 4 require a clock to be enabled so let's enable them when the
driver is built.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
The set_header call in kwbimage.c adds a checksum to the end of the
image in addition to setting up the header. It 'helpfully' updates the
st_size to match the fact that the file is now longer. However, mkimage
uses this length in the munmap call. This can lead to unmapping an extra
page, of perhaps required data. When this happens, a SEGV can occur.
To prevent this from happening, the munmap call now uses the same length
that was passed to mmap. This could also have been fixed by not changing
the length in kwbimage.c, however changing it in the main file means
that other plugins will also not fall for the same trap.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
[cp: resolve checkpatch complaints]
Tested-by: Chris Packham <judge.packham@gmail.com>
This patch enables DM_SERIAL for the pandora board. Verified that
the default kernel can still be booted with this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Add support for loading U-Boot on the Broadcom 7260 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Change the configured serial console index to reflect that it is the
first physical UART, reorder some defconfig lines and move some
environment configuration from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Four different boards had different options for enabling cache
that were virtually all the same. This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c
This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations]
Signed-off-by: Tom Rini <trini@konsulko.com>
Following build warning appears when pinctrl-single is built for ARM64:
In file included from drivers/pinctrl/pinctrl-single.c:10:0:
drivers/pinctrl/pinctrl-single.c: In function ‘single_configure_pins’:
./arch/arm/include/asm/io.h:43:28: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
#define __arch_getw(a) (*(volatile unsigned short *)(a))
Fix this by using phys_addr_t for variable reg instead of u32
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
timer_pre_probe() tries to populate the clock rate from DT. omap
timer driver tries to overwrite this value irrespective of the value
populated fro DT. So update this value only when DT doesn't populate
the clock rate.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In order to handle counter overflows use 64 bit values for counter.
Also load the initial value during probe.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The strobe dll code is ported from Linux Kernel:
drivers/mmc/host/sdhci-esdhc-imx.c
The comments are from the above file,
"For HS400 eMMC, there is a data_strobe line. This signal is generated
by the device and used for data output and CRC status response output
in HS400 mode. The frequency of this signal follows the frequency of
CLK generated by host. The host receives the data which is aligned to the
edge of data_strobe line. Due to the time delay between CLK line and
data_strobe line, if the delay time is larger than one clock cycle,
then CLK and data_strobe line will be misaligned, read error shows up.
So when the CLK is higher than 100MHz, each clock cycle is short enough,
host should configure the delay target. "
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Add HS400 support.
Selecting HS400 needs first select HS200 according to spec, so use
a dedicated function for HS400.
Add HS400 related macros.
Remove the restriction of only using the low 6 bits of
EXT_CSD_CARD_TYPE, using all the 8 bits.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit fixes various devicetree warnings in the at91 devicetrees
like:
arch/arm/dts/sama5d36ek_cmp.dtb: Warning (avoid_unnecessary_addr_size): /gpio_keys: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
These warnings make buildman report failed builds for most of at91 boards.
Thus, fixing it.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
For at91family, makefile was building unwanted DTBs
Moved them under specific target configuration.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Replace clrsetbits on ODR register (2 operations: one read + one write)
by writing on the correct bit (SET or RESET) of the BSRR register
(only 1 write operation).
Moreover this register if safe for simultaneous access by 2 master on
the bus.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds support for :
- Rate calculation through muxes and generic dividers
- Basic gate setting propagation
- Reparenting for muxes
- Clock rate setting through generic dividers without reparenting
Support is only added to the Composite VPU and VAPB clocks in order
to support the Video Processing Unit Power Domain clock setup.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson SoCs embeds a specific Power Domain dedicated to the
Video Processing Unit.
This patch implements support for this power domain in preparation of the
future support for the Video display support in U-Boot.
This driver will depend on changes in the clock driver to handle the setup
of the VPU and VAPB clocks configured from DT using assigned-clocks entries.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
All architectures have the same definition for s8/16/32/64
and u8/16/32/64.
Factor out the duplicated code into <asm-generic/int-ll64.h>.
BTW, Linux unified the kernel space definition into int-ll64.h
a few years ago as you see in Linux commit 0c79a8e29b5f
("asm/types.h: Remove include/asm-generic/int-l64.h").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You do not need to use the typedefs provided by compiler.
Our compilers are either IPL32 or LP64. Hence, U-Boot can/should
always use int-ll64.h typedefs like Linux kernel, whatever the
typedefs the compiler internally uses.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers. This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.
The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.
The following size changed apply to omap3_logic using GCC.
Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485 d9675 u-boot
Without Armv5
text data bss dec hex filename
50916 429 67580 118925 1d08d spl/u-boot-spl
540719 22700 327064 890483 d9673 u-boot
mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941 1d09d spl/u-boot-spl
540519 22700 327080 890299 d95bb u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
setparity users has been updated to use new setconfig ops,
so we can safely remove setparity ops
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace stm32_serial_setparity by stm32_serial_setconfig
which allows to set serial bits number, parity and stop
bits number.
Only parity setting is implemented.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace setparity by more generic setconfig ops
to allow uart parity, bits word length and stop bits
number change.
Adds SERIAL_GET_PARITY/BITS/STOP macros.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Unify the fgetc function when MUX is activated or not:
- always call tstc() : it is the normal behavior expected
by serial uclass (call tstc then getc) and that avoids
issue when SERIAL_RX_BUFFER is activated
- reload WATCHDOG in the char waiting loop
This patch allow to have the same behavior when CONSOLE_MUX is activated
or not and avoid regression when this feature is deactivated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test to avoid access to rx buffer when this buffer is empty.
In this case directly call getc() function to avoid issue when tstc()
is not called.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Activate the serial rx buffer.
Prepare console MUX activation with vidconsole, and avoid console
performance issue (missing character for copy-paste).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
If the OOB size is not multiple of the cache line size, the ARMv7
cache operation still prints "Misaligned operation at range".
=> nand info
Device 0: nand0, sector size 256 KiB
Page size 4096 b
OOB size 224 b
Erase size 262144 b
subpagesize 4096 b
options 0x00104200
bbt options 0x00060000
=> nand dump 0
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
CACHE: Misaligned operation at range [9fb15280, 9fb16360]
...
The cache flushing operations won't happen in this case to cover all of
the range to fix this by making sure we have things aligned.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Reword the commit message to be clear this is a direct problem
rather than just a warning]
The get_next_memory_node() always sets mem to -1 , which is incorrect,
because then every iteration of memory bank parsing will start from the
first memory bank instead of the previous one.
On systems with 1 memory bank defined in DT and CONFIG_NR_DRAM_BANKS=4 ,
like ie. r8a77965-salvator-x , this will result in U-Boot incorrectly
reporting four identical memory banks with the same memory configuration.
Fix this by setting mem to startoffset value, which restores the behavior
before the fixed patch was applied.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Fixes: 452bc12102 ("fdt: fix fdtdec_setup_memory_banksize()")
Tested-by: Michal Simek <michal.simek@xilinx.com> [on ZynqMP}
In commit a1274cc94a ("ARM: Page align secure section only when it is
executed in situ"), we used output section attributes (the "ALIGN"
keyword after the colon) to specify the alignment requirements. Using
the constant "COMMONPAGE" there was recently broken in binutils 2.31 [1].
Binutils maintainer Alan Modra suggested the former method would still
work. Since both methods achieve the same result, this patch does just
that. This fixes the "reboot after bootm" issue we've been seeing on
sunxi when booting non-secure.
[1] https://sourceware.org/bugzilla/show_bug.cgi?id=23571
Suggested-by: Alan Modra <amodra@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Jagan Teki <jagan@openedev.com>
QEMU 3.0 introduced additional memory-mapped regions for PCI-E ECAM and
MMIO. Thus we need to add them to our MMU map or U-Boot will crash with
a Synchronous Abort during PCI-E probing when it tries to access the
unmapped ECAM memory area.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Without this patch the Ethernet PHY on the p212 board does not get
fully configured.
When this happens Ethernet does not function.
The similar libretech-cc and khadas-vim boards have this code already.
That's why the Ethernet on these boards do work.
Signed-off-by: Jasper Kcoding <jasperkcoding@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
When booting the QEMU virt machine with -net nic,model=e1000 we can already
support network boot just fine today.
So let's enable the default bootcmd to also evaluate DHCP responses properly.
That way we can enable network boot seamlessly with the virt target.
Signed-off-by: Alexander Graf <agraf@suse.de>
When re-syncing the DTS files from the kernel, something caused
the MMC driver to no longer detect the MMC card. Undoing the
CD-invert appears to fix the issue.
Fixes: e6ea2390cd ("ARM: DTS: Resync LogicPD-Torpedo-37xx-devkit
with Linux 4.18-RC4")
Signed-off-by: Adam Ford <aford173@gmail.com>
CPU (and hence cpu timers) on HSDK board runs at 500MHz after
preloader so fix wrong CPU frequency value in hsdk.dts
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Add an entry for mx7dsabresd_qspi_defconfig to avoid the following
warnings:
WARNING: no status info for 'mx7dsabresd_qspi'
WARNING: no maintainers for 'mx7dsabresd_qspi'
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This commit adds support for the Toradex Colibri iMX7D 1GB Computer
on Module. The module is very similar to the Colibri iMX7D 512MB
but uses eMMC instead of raw NAND. This patch introduces a new
board specific Kconfig symbol to select between the two flash
options.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This patch adds system suspend/resume support,
when linux kernel enters deep sleep mode, SoC will go
into below mode:
- CA7 platform goes into STOP mode;
- SoC goes into DSM mode;
- DDR goes into self-refresh mode;
- CPU0/SCU will be powered down.
When wake up event arrives:
- SoC DSM mdoe exits;
- CA7 platform exit STOP mode, SCU/CPU0 power up;
- Invalidate L1 cache;
- DDR exit self-refresh mode;
- Do secure monitor mode related initialization;
- Jump to linux kernel resume entry.
Belwo is the log of 1 iteration of system suspend/resume:
[ 338.824862] PM: suspend entry (deep)
[ 338.828853] PM: Syncing filesystems ... done.
[ 338.834433] Freezing user space processes ... (elapsed 0.001 seconds) done.
[ 338.842939] OOM killer disabled.
[ 338.846182] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 338.869717] PM: suspend devices took 0.010 seconds
[ 338.877846] Disabling non-boot CPUs ...
[ 338.960301] Retrying again to check for CPU kill
[ 338.964953] CPU1 killed.
[ 338.968104] Enabling non-boot CPUs ...
[ 338.973598] CPU1 is up
[ 339.267155] mmc1: queuing unknown CIS tuple 0x80 (2 bytes)
[ 339.275833] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 339.284158] mmc1: queuing unknown CIS tuple 0x80 (6 bytes)
[ 339.385065] PM: resume devices took 0.400 seconds
[ 339.389836] OOM killer enabled.
[ 339.392986] Restarting tasks ... done.
[ 339.398990] PM: suspend exit
The resume entry function has to initialize stack pointer before calling
C code, otherwise there will be an external abort occur, in additional,
invalidate L1 cache must be done in secure section as well, so this
patch also adds assembly code back and keep it as simple as possible.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Add i.MX7D GPC initialization for low power mode
support like system suspend/resume from linux kernel:
- Pending IOMUXC IRQ to workaround GPC state machine issue;
- Mask all GPC interrupts for M4/C0/C1;
- Configure SCU timing;
- Configure time slot ack;
- Configure C0/C1 power up/down timing;
- Configure wakeup source mechanism;
- Disable DSM/RBC related settings.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
This patch improves cpu hotplug, previous cpu_off
implementation is NOT safe, a CPU can NOT power down
itself in runtime, it will cause system bus hang due
to pending transaction. So need to use other online
CPU to kill it when it is ready for killed.
Here use SRC parameter register and a magic number
of ~0 as handshake for killing a offline CPU,
when the online CPU checks the psci_affinity_info,
it will help kill the offline CPU according to
the magic number stored in SRC parameter register.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
CONFIG_BOOTDELAY has been migrated to Kconfig, but cl-som-imx7 was
missed. We can just delete the assignments as the config already has
the correct value.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The existing imx_watchdog driver is compatible with mx25 chipsets.
Add a WDOG1_BASE_ADDR define for the base address and enable the driver
in watchdog's Makefile.
To use the driver, a board must define CONFIG_IMX_WATCHDOG and
CONFIG_HW_WATCHDOG.
This fixes an issue when booting an mx25 chip via usb/serial. In this
case, the boot rom will always enable the watchdog. If u-boot is running
in interactive mode and the watchdog is not serviced, the system is
rebooted when the watchdog expires.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Convert the codes and configurations to enable DM drivers in u-boot for
modules: i2c, PMIC, regulator, USB, Ethernet, SD/MMC, GPIO and QSPI
This patch does not change SPL, so it still uses non-DM driver for
UART, GPIO and SD/MMC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Add the board DTS files for 14x14 EVK and 9x9 EVK. They are necessary
for converting to use u-boot DM driver.
Two -u-boot.dtsi are added to modify compatible string of SPI flash
device to "spi-flash".
Signed-off-by: Ye Li <ye.li@nxp.com>
On iMX7D SabreSD board, the QSPI has pins conflict with EPDC (default).
To use QSPI, users have to rework the board (de-populate R388-R391, R396-R399
populate R392-R395, R299, R300). So we add new DTS file and new defconfig
dedicated for QSPI.
Other changes to support the DM QSPI:
- Add QSPI node and alias spi0.
- Modify spi4 (spi-gpio) node and add alias spi5 for it to avoid req
conflict
- Add EPDC node in imx7d.dtsi and disable it in imx7d-sdb-qspi.dts to
align with kernel and also present the conflict.
- Add -u-boot.dtsi to modify compatible string of mx25l51245g@0 to
"spi-flash"
- Remove iomux settings of qspi in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver:
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI and DM SPI FLASH configurations
- Remove iomux settings of qspi1 in board codes which is not needed
for DM driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
To support DM QSPI driver
- Add spi0 and spi1 alias for qspi1 and qspi2.
- Add -u-boot.dtsi to modify n25q256a@0 and n25q256a@1 compatible string
to "spi-flash" and add "num-cs" property.
- Enable DM SPI/QSPI relavent configurations
- Remove iomux settings of qspi2 in board codes which is not needed
for DM driver.
- Add sf default settings. So running "sf probe" can detect the flash
Signed-off-by: Ye Li <ye.li@nxp.com>
In Linux, the memory returned by kmalloc() is DMA-capable.
However, it is not true in U-Boot.
At a glance, kmalloc() in U-Boot returns address aligned with
ARCH_DMA_MINALIGN. However, it never pads the allocated memory.
This half-way house is completely useless because calling kmalloc()
and malloc() in this order causes a cache sharing problem.
Change the implementation to call malloc_cache_aligned(), which
allocates really DMA-capable memory.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
argc = 1: all tests are run
argc > 1: only argv[1] is run
So we need argc >= 1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the HiKey board instructions based on the latest source
available. These instructions are derived from the ATF platform doc.
While updating the instructions, some comments on ATF issue has been
removed since it is fixed in latest ATF source.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
As of today, the proposal of adding "acpi_rsdp_addr" to the kernel
boot protocol does not make its way to the kernel mainline. This
creates some confusion if we leave it in the U-Boot code base.
Remove it for now until we have a clear picture with kernel upstream.
Note this eventually does a partial revert to commit 3469bf4274
("x86: zImage: Propagate acpi_rsdp_addr to kernel via boot parameters")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have full Linux kernel boot support on EFI payload,
avoid pass "acpi=off" to the kernel command line.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present Linux kernel loaded from U-Boot as an EFI payload does
not boot. This fills in kernel's boot params structure with the
required critical EFI information like system table address and
memory map stuff so that kernel can obtain essential data like
runtime services and ACPI table to boot.
With this patch, now U-Boot as an EFI payload becomes much more
practical: it is another option of kernel bootloader, ie, can be
a replacement for grub.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This updates the EFI stub codes to pass UEFI BIOS's system table
address to U-Boot payload so that U-Boot can utilize it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This implements payload-specific install_e820_map() to get E820 map
from the EFI memory map descriptors.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add code to reset all reset signals as in usb DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Only PCI device 1 and 2 is populated on the R-Car Gen2 internal
PCIe controller. Ignore all other devices. This fix prevents a
duplication of OHCI controller response on slot 0 and 1.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Add support for operating a PHY attached to ehci-pci. There are
systems where the EHCI controller is internally wired to a PCI
bus and has a PHY connected to it as well, ie. the R-Car Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Fix this sort of warning if generic-phy.h is included:
include/generic-phy.h:52:42: warning: ‘struct ofnode_phandle_args’ declared inside parameter list will not be visible outside of this definition or declaration
int (*of_xlate)(struct phy *phy, struct ofnode_phandle_args *args);
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
beagleboard x15 is the first supported platform variant of am57xx
in AOSP (android open source project) now.
changing board name to stay in consistent with aosp target name.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
It is not preferred to put SUNXI-specific code in the common place.
Change it to 'imply' property of ARCH_SUNXI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Copy missing Kernel patch to make SLEWCTRL_SLOW available in device tree
and to correct the value of SLEWCTRL_FAST.
After this patch, the Kernel and U-boot device tree settings for
SLEWCTRL have the same effect.
Original Kernel patch message:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=424e0f039bfa8a51fb5c5178b6ece8baa4996469
"
According to AM335x TRM, Document spruh73l, Revised February 2015,
Section 9.2.2 Pad Control Registers, setting bit 6 of the pad control
registers actually sets the SLEWCTRL value to slow rather than fast as
the current macro indicates. Introduce a new macro, SLEWCTRL_SLOW, that
sets the bit, and modify SLEWCTRL_FAST to 0 but keep it for
completeness. Current users of the macro (i2c and mdio) are left
unmodified as SLEWCTRL_FAST was the macro used and actual desired state.
Tested on am335x-gp-evm with no difference in software performance seen.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
"
Signed-off-by: Christian Amann <Christian.Amann@de.bosch.com>
Add missing environment name for UBI, to prevent this NULL in output:
Loading Environment from <NULL>...
and rather have a valid UBI there:
Loading Environment from UBI...
Signed-off-by: Marek Vasut <marex@denx.de>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Currently when using bootelf to load an image on Arm, several warnings
such as the following appear in the console:
CACHE: Misaligned operation at range [87800000, 8783c5e0]
CACHE: Misaligned operation at range [8783c5e0, 8784b3e0]
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Reword commit message to include the info after the --- which
included the Signed-off-by line, and change ' at ' to '@']
Signed-off-by: Tom Rini <trini@konsulko.com>
malloc_simple() can return 0 if out of memory. Don't call memset
from calloc() in this case but rely on the caller checking
the return value.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In an earlier proposed patch, bcmstb.c implemented timer_read_counter,
but it was updated to implement get_ticks instead. This patch updates
the declaration in timer.h accordingly.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
The reset is already handled by the designware driver using
information from device tree.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Compiling U-Boot with ubsan/asan libraries and running it in sandbox
may lead to below backtrace:
=> avb init 0
=> avb verify
## Android Verified Boot 2.0 version 1.1.0
read_is_device_unlocked not supported yet
common/avb_verify.c:407:31: runtime error: division by zero
AddressSanitizer:DEADLYSIGNAL
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
=================================================================
==9388==ERROR: AddressSanitizer: FPE on unknown address 0x0000004b467f \
(pc 0x0000004b467f bp 0x000000000000 sp 0x7ffd899fe150 T0)
#0 0x4b467e in mmc_byte_io common/avb_verify.c:407
#1 0x4b4c47 in mmc_byte_io common/avb_verify.c:532
#2 0x4b4c47 in read_from_partition common/avb_verify.c:533
#3 0x69dc0d in load_and_verify_vbmeta lib/libavb/avb_slot_verify.c:560
#4 0x6a1ee6 in avb_slot_verify lib/libavb/avb_slot_verify.c:1139
#5 0x45dabd in do_avb_verify_part cmd/avb.c:245
#6 0x4af77c in cmd_call common/command.c:499
#7 0x4af77c in cmd_process common/command.c:538
#8 0x46bafc in run_pipe_real common/cli_hush.c:1677
#9 0x46bafc in run_list_real common/cli_hush.c:1875
#10 0x46c780 in run_list common/cli_hush.c:2024
#11 0x46c780 in parse_stream_outer common/cli_hush.c:3216
#12 0x46d34b in parse_file_outer common/cli_hush.c:3299
#13 0x4ad609 in cli_loop common/cli.c:217
#14 0x4625ae in main_loop common/main.c:65
#15 0x46f2d1 in run_main_loop common/board_r.c:648
#16 0x640253 in initcall_run_list lib/initcall.c:30
#17 0x46f9d0 in board_init_r common/board_r.c:879
#18 0x40539b in main arch/sandbox/cpu/start.c:321
#19 0x7fa94925f82f in __libc_start_main (/lib/x86_64-linux-gnu/libc.so.6+0x2082f)
#20 0x408908 in _start (/srv/R/u-boot-master/u-boot+0x408908)
AddressSanitizer can not provide additional info.
SUMMARY: AddressSanitizer: FPE common/avb_verify.c:407 in mmc_byte_io
==9388==ABORTING
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Cppcheck (v1.85) reports w/o this patch:
[common/avb_verify.c:738] -> [common/avb_verify.c:741]: (warning) \
Either the condition 'ops' is redundant or there is possible null \
pointer dereference: ops.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fix sparse complaint:
common/avb_verify.c:14:21: warning: \
symbol 'avb_root_pub' was not declared. Should it be static?
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Fix below compiler [1] warning:
common/avb_verify.c: In function ‘avb_find_dm_args’:
common/avb_verify.c:179:30: warning: left-hand operand of comma expression has no effect [-Wunused-value]
for (i = 0; i < AVB_MAX_ARGS, args[i]; ++i) {
[1] aarch64-linux-gnu-gcc (Linaro GCC 7.2-2017.11)
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Exit with AVB_SLOT_VERIFY_RESULT_ERROR_INVALID_ARGUMENT
when hashtree_error_mode value passed to avb_append_options()
is unknown (not from AvbHashtreeErrorMode enum).
Otherwise, default value is not handled in the
switch(hashtree_error_mode), which causes below compile warning:
lib/libavb/avb_cmdline.c: In function ‘avb_append_options’:
lib/libavb/avb_cmdline.c:354:13: warning: ‘dm_verity_mode’ may be used uninitialized in this function [-Wmaybe-uninitialized]
new_ret = avb_replace(
~~~~~~~~^~~~~~~~~~~~~~
slot_data->cmdline, "$(ANDROID_VERITY_MODE)", dm_verity_mode);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
lib/libavb/avb_cmdline.c:363:8: warning: ‘verity_mode’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (!cmdline_append_option(
^~~~~~~~~~~~~~~~~~~~~~
slot_data, "androidboot.veritymode", verity_mode)) {
Signed-off-by: Ievgen Maliarenko <ievgen.maliarenko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Switch the Arria10 from ad-hoc hardcoded timer to timer framework
and the DW APB timer driver. This allows the A10 to extract timer
information, like timer rate, from clock framework and thus DT
instead of having it hardcoded in U-Boot configuration files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Flag timer clock as DM pre-reloc, so that a timer driver can be used and
it can extract information about it's clock rate using the clock framework.
This patch also moves some of the pre-reloc flags into the core dtsi file,
this is because the timer is not board specific, but rather is used on all
boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The Arria10 SPL is a complete mess of calls to functions which are
called in the wrong context and it is surprise it works at all. This
patch tries to clean that mess up by shuffling the function calls
around and moving the calls into the correct context. Due to the
delicate nature of the reordering, this is done in one huge patch.
The following changes happen in this patch:
- Security policy init and NIC301 happens first in board_init_f()
- The clock init happens very early in board_init_f() in SPL only
- arch_early_init_r() only registers the FPGA, just like on Gen5
- arch_early_init_r() is never called from any _f() function
- Dedicated FPGA pins are inited in board_init_f() as on Gen5
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
According to mailbox spec, software should send urgent command with
urgent register instead of COUT location. This patch write urgent
command index to urgent register.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Code checking and setting EMAC use fpga is in
populate_sysmgr_fpgaintf_module(). So, call to sysmgr_pinmux_init()
instead of populate_sysmgr_pinmux().
In sysmgr_pinmux_init(), it will call to both populate_sysmgr_pinmux()
and populate_sysmgr_fpgaintf_module().
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This partially reverts commit 7e21fbca26.
That change broke sandbox EFI support for unknown reasons. It also changes
sandbox to use--gc-sections which we don't want.
For now I am just reverting the sandbox portion as presumably this change
is safe on other architectures.
Fixes: 7e21fbca26 (efi_loader: Rename sections to allow for implicit data)
Signed-off-by: Simon Glass <sjg@chromium.org>
Update README.falcon to use "none" for compression property for
ramdisk image to avoid being uncompressed upon loading.
Signed-off-by: York Sun <york.sun@nxp.com>
musb stop is musb core call during unregister or shutting down
gadget or host musb. For graceful exit add musb_platform_exit
on musb_stop so-that it can exit the musb platform driver as well.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
musb have platform ops to do proper graceful exit,
so add the exit call and move musb platform exit code
instead of keeping it in driver remove.
This make proper shutdown of musb where .remove will
call disable, exit serially via musb_stop.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
reset0 is not available for sun4i, 5i and 7i so access
the reset0 offset from ccm via driver data for relevant
Allwinner SoC. this will eventually drop the existing
ifdef for SUN6I.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Allocate struct phy in private structure instead of allocating
locally and assign it to a pointer. This eventually fix miss
alignment phy which is used in another functions.
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When MUSB is operating in peripheral mode, probe registering
musb core using musb_register which intern return int value
for validation. so there is no scope to preserve struct musb
pointer but the same can be used in .remove musb_stop.
So fix this by return musb_register with struct musb pointer.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Purna Chandra Mandal <purna.mandal@microchip.com>
Tested-by: Chen-Yu Tsai <wens@csie.org> # A33-OlinuXino
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Patch queue for efi - 2018-08-21
A few fixes for 2018.09. Most noticable are:
- unbreak x86 target (-fdata-section fallout)
- fix undefined behavior in a few corner cases
- make Jetson TX1 boot again
- RTS fixes
- implement reset for simple output
A secure monitor that runs before U-Boot, and hence causes U-Boot to run
in non-secure world, must implement a few operations that U-Boot
otherwise implements when running in secure world. Fix U-Boot to skip
these operations when running in non-secure world. In particular:
- The secure monitor must provide the LP0 resume code and own LP0
configuration in order to maintain security, so must initialize all
the PMC scratch registers used by the boot ROM during LP0 resume.
Consequently, U-Boot should not attempt to clear those registers,
since the register accesses will fail or cause an error.
- The secure monitor owns system security, and so is responsible for
configuring security-related items such as the VPR.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since commit f2faffecb0, tegra: Convert to use binman
the dm-pre-reloc properties are removed.
This leads U-Boot not to enable the display on paz00
This patch restore the dm-pre-reloc properties allowing
the bootloader to output to the display panel
v4: - Spell project name as appropriate
v3: - Fix few typos
v2: - Add more characters to commit hash
Signed-off-by: Nicolas Chauvet <kwizart@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In some cases it can be useful to be able to bind a device to a driver from
the command line.
The obvious example is for versatile devices such as USB gadget.
Another use case is when the devices are not yet ready at startup and
require some setup before the drivers are bound (ex: FPGA which bitsream is
fetched from a mass storage or ethernet)
usage example:
bind usb_dev_generic 0 usb_ether
unbind usb_dev_generic 0 usb_ether
or
unbind eth 1
bind /ocp/omap_dwc3@48380000/usb@48390000 usb_ether
unbind /ocp/omap_dwc3@48380000/usb@48390000
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also add a 'drv' parameter to filter the children to remove/unbind.
Exporting those functions is a preparatory work for the addition of the
bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also add device_find_global_by_ofnode() that also find a device based on
the OF node, but doesn't probe the device.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Command "dm tree" dumps the devices with class, driver, name information.
Add the index of the device in the class too, because the information is
useful for the bind/unbind commands.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is the reciprocal of uclass_find_device().
It will be used to print the index information in dm tree dump.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When a USB ethernet device is halted, the device driver is removed. When
this happens the uclass private memory is freed and uclass_priv is set to
NULL. This causes a data abort when uclass_priv->state is then set to
ETH_STATE_PASSIVE.
Fix it by checking if uclass_priv is NULL before setting uclass_priv->state
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add an entry in usb_gadget_controller_number() for the DWC3 gadget
controller. Without it, it is not possible to bind the USB Ethernet driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With upcoming changes that require CONFIG_BLK, this broke
USB Mass Storage on the OMAP3 boards because if CONFIG_BLK is
enabled, it assumes that DM_USB is enabled, but it wasn't yet
available on omap3 and omap4 boards.
This patch converts the OMAP2430 MUSB glue to support DM_USB and
extracts the necessary information based on the device tree.
It's based on the ti-musb driver, but there are enough significant
differences in both the architecture and device tree entires between
am33xx and OMAP3/OMAP4, that I think it makes sense to continue to
keep the separate.
Per doc/driver-model/usb-info.txt, the USB gadget stuff hasn't
migrated to DM_USB yet, so this only supports USB Host for now.
Users wanting USB Gadgets will need to disable DM_USB and leave
it the old way for now.
Signed-off-by: Adam Ford <aford173@gmail.com>
A bunch of code was encapsulated in #ifdef's whether or not
it is building or for U-Boot. Since this code is always building
for U-Boot, this patch removes the dead code.
Signed-off-by: Adam Ford <aford173@gmail.com>
In case when user provides '-' as USB controller index, like this:
=> fastboot -
data abort occurs in strcmp() function in do_fastboot(), here:
if (!strcmp(argv[1], "udp"))
(tested on BeagleBone Black).
That's because argv[1] is NULL when user types in the '-', and null
pointer dereference occurs in strcmp() (which is ok according to C
standard specification). So we must validate user input to prevent such
behavior.
While at it, check also the result of strtoul() function and handle
error cases properly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Fix cppcheck complaint:
[cmd/efi.c:173]: (style) Clarify calculation precedence for '&' and '?'.
Fixes: f1a0bafb58 ("efi: Add a command to display the memory map")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Starting with commit 867a6ac86d ("efi: Add start-up library code"),
sparse constantly complains about truncated constant value in efi.h:
include/efi.h:176:35: warning: cast truncates bits from constant value (8000000000000000 becomes 0)
This can get quite noisy, preventing real issues to be noticed:
$ make defconfig
*** Default configuration is based on 'sandbox_defconfig'
$ make C=2 -j12 2>&1 | grep truncates | wc -l
441
After the patch is applied:
$ make C=2 -j12 2>&1 | grep truncates | wc -l
0
$ sparse --version
v0.5.2
Following the suggestion of Heinrich Schuchardt, instead of only
fixing the root-cause, I replaced the whole enum of _SHIFT values
by ULL defines. This matches both the UEFI 2.7 spec and the Linux
kernel implementation.
Some ELF size comparison before and after the patch (gcc 7.3.0):
efi-x86_payload64_defconfig:
text data bss dec hex filename
407174 29432 278676 715282 aea12 u-boot.old
407152 29464 278676 715292 aea1c u-boot.new
-22 +32 0 +10
efi-x86_payload32_defconfig:
text data bss dec hex filename
447075 30308 280076 757459 b8ed3 u-boot.old
447053 30340 280076 757469 b8edd u-boot.new
-22 +32 0 +10
Fixes: 867a6ac86d ("efi: Add start-up library code")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the reset service of the EFI_SIMPLE_TEXT_OUTPUT_PROTOCOL.
This should resolve the error reported by the SCT in
Protocol/SimpleTextOut/BlackBoxTest/SimpleTextOutBBTestFunction_uefi.c:639
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI specification mandates that the create flag is only used in
conjunction with both the read and the write flag.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The crc32 of the runtime services table must be updated after detaching.
efi_update_table_header_crc32() must be __efi_runtime. So move it to
efi_runtime.c
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function crc32() is needed by the EFI subsystem at runtime. So it has
to be linked into the runtime section together with all dependencies.
Eliminate empty defines local and ZEXPORT.
Mark variables as static which are not exported.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should only dereference parameter memory_map_size after checking that
it is valid.
Fixes: 8e835554b3 ("efi_loader: check parameters of GetMemoryMap")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
variables buf from board_mmc_init, and ret from misc_init_r
were unused on the functions, so remove it.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The commit 21b3edfc96 ("efi_loader: check parameters of CreateEvent")
enforces a strict parameter check at CreateEvent(). On the other hand,
UEFI specification version 2.7, section 7.1, says:
The EVT_NOTIFY_WAIT and EVT_NOTIFY_SIGNAL flags are exclusive. If
neither flag is specified, the caller does not require any notification
concerning the event and the NotifyTpl, NotifyFunction, and
NotifyContext parameters are ignored.
So the check should be mitigated so as to comply with the specification.
Without this patch, EDK2's Shell.efi won't be started.
Fixes: 21b3edfc96 ("efi_loader: check parameters of CreateEvent")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When we build with -fdata-sections we may end up with bss subsections. Our
linker script explicitly lists only a single consecutive bss section though.
Adapt the statement to also include subsections.
Signed-off-by: Alexander Graf <agraf@suse.de>
We left -fdata-sections disabled for x86_64 before because we encountered
random bugs that were at that time inexplicable.
Turns out this really was just side effects of missing .bss* statements
in the linker scripts. With those fixed, we can enable data sections for all
targets.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we build with -fdata-sections we may end up with bss subsections. Our
linker script explicitly lists only a single consecutive bss section though.
Adapt the statement to also include subsections.
This fixes booting efi-x86_app_defconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
In the current H6 CPU memory space code, the SUNXI in the macro name of
the SID address base is wrongly spelled as SNUXI, which leads to SID
readout not working.
Fix this macro name.
Fixes: 55f6b1c351c9 ("sunxi: add basic memory map definitions of H6 SoC")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
dtimg command allows user to work with Android DTB/DTBO image format.
Such as, getting the address of desired DTB/DTBO file, printing the dump
of the image in U-Boot shell, etc.
This command is needed to provide Android boot with new Android DT image
format further.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Android documentation recommends new image format for storing DTB/DTBO
files: [1]. To support that format, this patch adds helper functions for
Android DTB/DTBO format. In image-android-dt.* files you can find helper
functions to work with Android DT image format, such us routines for:
- printing the dump of image structure
- getting the address and size of desired dtb/dtbo file
This patch uses dt_table.h file, that was added in commit 643cefa4d8
("Import Android's dt_table.h for DT image format") by Alex Deymo.
[1] https://source.android.com/devices/architecture/dto/partitions
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
In order to make the debug print in file_fat_read_at() a tad more useful,
show the offset the file is being read at alongside the filename.
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
spl_common_init() debug-prints "spl_early_init()\n" but it is
called both from spl_early_init() and spl_init().
Fix this by moving the debug() statement to the calling functions
which now print their name.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The da850evm with its UI expander board can boot XIP boot from
NOR flash. This adds the instructions to the readme. file.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL space is limited. In order to try to enable DM in SPL,
we need more space. When combined wtih TINY_PRINTF, this reduces
the size of SPL by 6.5k
Original:
text data bss dec hex filename
20760 1216 80 22056 5628 spl/u-boot-spl
Tiny Printf
text data bss dec hex filename
17947 1216 80 19243 4b2b spl/u-boot-spl
Malloc Simple + Tiny Printf
text data bss dec hex filename
15187 176 28 15391 3c1f spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL space is limited. In order to try to enable DM in SPL,
we need more space. This reduces the size of SPL by ~2.7K
before:
text data bss dec hex filename
20760 1216 80 22056 5628 spl/u-boot-spl
after:
text data bss dec hex filename
17947 1216 80 19243 4b2b spl/u-boot-spl
Signed-off-by: Adam Ford <aford173@gmail.com>
Since using DM_I2C_COMPAT throws a warning during compilation,
and it isn't really needed any longer, so this patch removes
this feature and shrinks the code a bit.
from:
text data bss dec hex filename
343326 13388 123448 480162 753a2 u-boot
to:
text data bss dec hex filename
342924 13380 123440 479744 75200 u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
When applying a virtual memory map we have to update the pointer to the
list of configuration tables.
Fixes: 4182a129ef ("efi_loader: allocate configuration table array")
Reported-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit aa909462d0. This change
caused "dhcp filename" to crash the system on p2371-2180 (Jetson TX1), for
example when running test/py.
Reverting this change isn't optimal, but at least restores TX1 to a working
state. In the future, we should:
a) Fix whatever problem causes the crash with this patch applied. This
needs further discussion, so isn't something we can immediately do.
b) Undo the revert; re-apply the original patch to efi_allocate_pages.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Something went wrong when writing the sandbox linker scripts and so we
ended up with a .bss section marker right before the efi runtime sections.
That obviously is a terrible idea, as it may result in overwriting efi
runtime code and data. So let's move the .bss identifier behind the efi
sections.
Signed-off-by: Alexander Graf <agraf@suse.de>
It was observed sometimes U-Boot as the EFI payload fails to boot on
QEMU. This is because TSC calibration fails with no valid frequency.
This adds default TSC frequency in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It was observed sometimes U-Boot as the coreboot payload fails to
boot on QEMU. This is because TSC calibration fails with no valid
frequency. This adds default TSC frequency in the device tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
At present if TSC frequency is provided in the device tree, it takes
precedence over hardware calibration result. This swaps the order to
try hardware calibration first and uses device tree as last resort.
This can be helpful when a generic dts (eg: coreboot/efi payload) is
supposed to work on as many hardware as possible, including emulators
like QEMU where TSC hardware calibration sometimes fails.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
There is no need to keep a separate coreboot_fb.dtsi since now we
have a generic coreboot payload dts.
While we are here, this also remove the out-of-date description in
the documentation regarding to coreboot framebuffer driver with
U-Boot loaded as a payload from coreboot. As the testing result with
QEMU 2.5.0 shows, the driver just works like a charm.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Since gcc-8 the --enable-default-pie starts producing code which assembler
can't translate in case of U-Boot. The build fails with
{standard input}: Assembler messages:
{standard input}:21100: Error: junk at end of line, first unrecognized character is `@'
{standard input}:21120: Error: junk at end of line, first unrecognized character is `@'
and so on.
This is usually the case for x86 platform because in many cases it uses host
compiler from the Linux distributions, where PIE is enabled by default.
Previously (gcc-7 and earlier) that was a potential issue due to absence of
constructions like
.long end.5561@gotoff-start.5558@gotoff
which are a cause of above error messages in gcc-8.
Fix all these by disabling PIE on Makefile level.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no reason to have the same Kconfig options for different SoCs
separately. The patch is merging them together.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
[trini: Fix ENV_SIZE around ENV_IS_NOWHERE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
After creating CONS_INDEX and migrating a bunch of boards to it,
there are a bunch of defined references to CONFIG_SERIALx which
are not referenced in any C code or #ifdef, so they can now be
removed
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_TWL4030_LED
CONFIG_TWL4030_INPUT
This also removes dead references to:
CONFIG_TWL4030_KEYPAD
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_MISC_INIT_R
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Update the defaults logic slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate boards which set bootlimit in the environment to Kconfig.
We exclude gurnard_defconfig which includes a bootlimit=, but doesn't set
CONFIG_BOOTCOUNT_LIMIT, so we'd fail to include a bootlimit setting
if we migrated it.
display5_defconfig and display5_factory_defconfig share a SYS_CONFIG_NAME,
but only display5_defconfig enables CONFIG_BOOTCOUNT_LIMIT, so we fail to
set bootlimit= in display5_factory_defconfig. This is okay because the
display5_factory_defconfig doesn't need to have it set, as it is only
meant to prepare the board in the factory.
Environment changes for all modified configs as seen from buildman:
boards.cfg is up to date. Nothing to do.
Summary of 3 commits for 32 boards (8 threads, 1 job per thread)
01: Merge git://git.denx.de/u-boot-x86
arm: + draco etamin rastaban pxm2 display5 thuban rut
02: Add BOOTCOUNT_BOOTLIMIT to set reboot limit
03: Migrate bootlimit to Kconfig
- display5_factory: bootlimit=3
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.
Signed-off-by: Tom Rini <trini@konsulko.com>
If CONFIG_NR_DRAM_BANKS is bigger than the default
value (4) define MEMORY_BANKS_MAX as CONFIG_NR_DRAM_BANKS.
Fixes: 2a1f4f1758 ("Revert "fdt_support: Use CONFIG_NR_DRAM_BANKS if defined"")
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
While we have long since migrated to CONFIG_SYS_GENERIC_BOARD being
enabled, we had just a few places left that still referenced or defined
it. Update.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable support for USB PHY on the R-Car Gen2. This allows for both
of the USB host ports to be used on such boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Use clock framework functions to fetch clock information now that there
is a clock driver for Arria10, instead of custom coded register parsing.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add the pre-reloc DT markers to clock nodes needed in SPL and early
U-Boot stages. This is required to let the Arria10 clock driver start
early and provide clock information for UART and SDMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The variables removed in this patch are never used, they are only ever
assigned and then waste precious memory. Drop both the assignment and
the variables.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The L4SP and MMC clock precalculation is specific to Gen5, it is not
needed on Arria10/Stratix10. Isolate it to Gen5 until there is a proper
clock driver for Gen5, at which point this will go away completely.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Bind fixed clock driver to the base clock instantiated in the handoff
DT and use DM clock framework to get their clock rate. This replaces
the ad-hoc DT parsing present thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Remove ad-hoc ethernet syscon registers configuration and reset support.
Reset is now handled by the reset framework and the syscon registers are
set in the dwmac_socfpga.c driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
The UART reset handling is now done via reset framework using the
SoCFPGA reset driver. The UART console assignment is done using the
DM and console framework. Nuke all this comlexity, since it is just
duplicating the same functionality, badly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Add the GMAC0,1 OCP resets, which must also be ungated for those GMACs
to work and add GMAC2 reset and OCP resets which were missing altogether.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Some of the code for low level system initialization in SPL's
board_init_f() and U-Boot's arch_early_init_r() is the same,
so let's combine it into a single function called from both.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Device trees need to have the serial console device available
before relocation and require a stdout-path in chosen at least
for SPL to have a console.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This patch fix the following warnings for for stm32f429
evaluation and discovery boards:
unnecessary #address-cells/#size-cells without "ranges" or
child "reg" property
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add ADC device tree node. This allows to get analog conversions on
stm32mp157.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This commit enables CONFIG_BLK and removes USB_STORAGE which is awaiting
proper implementation for current U-Boot interfaces. Additionally the
console selection is now handled by Kconfig and no longer needs to be in
the config header. CONFIG_SYS_MALLOC_F_LEN=0x2000 was added to sync with
other boards. CONFIG_SPL_BLK and CONFIG_SPL_DM_MMC are disabled because
they currently do not allow the OMAP3-EVM (OMAP34XX) to actually boot.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
The recv variable in sandbox_tpm2_fill_buf() is a pointer on a pointer
of a char array. It means accessing *recv is the char array pointer
itself while **recv is the first character of that array. There is no
need for such indirection here, so simplify the code.
Simplifying things will make the last assignment right: "*recv = NULL"
is now correct. The issue has been found by the following Coverity
Scan report:
CID 183371: Incorrect expression (UNUSED_VALUE)
Assigning value "4UL" to "*recv" here, but that stored value is overwritten before it can be used.
232 *recv += sizeof(rc);
233
234 /* Add trailing \0 */
235 *recv = NULL;
While at simplifying things, use '\0' instead of NULL when adding an
empty char at the end of the buffer.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The second check on pcr_map in sandbox_tpm2_xfer() is wrong. It should
check for pcr_map not being empty. Instead, it is a pure copy/paste of
the first check which is redundant.
This has been found thanks to a Coverity Scan report:
CID 183370: Memory - illegal accesses (UNINIT)
Using uninitialized value "pcr_index".
put_unaligned_be32(tpm->pcr_extensions[pcr_index], recv);
This is because pcr_index is initialized only if the user input is
correct, ie. at least one valid bit is set in pcr_map.
Fix the second check and also initialize pcr_index to 0 (which is
harmless in case of error) to make Coverity Scan happy.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add scattered driver files around the source tree
that belongs to Snapdragon arch. Not sure why they
were not included in the first place.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
1. Add FIT support for DB410c defconfig.
2. Don't overwrite bootargs (they're already
defined in Linux device tree for DB410c.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Change the way MAC address fixup is done:
1. Stop using LK handed device-tree and calculate
the MAC address our own.
2. Allow overriding the generated MACS with environment variables:
"wlanaddr" and "btaddr".
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add support for generation of unique MAC address
that is derived from board serial.
Algorithm for generation of MAC taken from LK.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This commit adds a function to get the board
serial number.
In snapdragon it's actually the eMMC serial number.
Function added in a new file misc.c that will
include further snapdragon miscellaneous functions.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Commit 1473b12ad0 ("lib: fdtdec: Update ram_base to store ram start
adddress") brings regression on STM32F7 which can't boot.
Use fdtdec_setup_mem_size_base() to setup memory base and size.
Use fdtdec_setup_memory_banksize() to setup memory bank base and size.
Reported-by: Mark Olsson <mark@markolsson.se>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Cc: Mark Olsson <mark@markolsson.se>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Since commit bfea69ad27 ("stm32f7: sdram: correct sdram
configuration as per micron sdram"), CONFIG_SYS_RAM_FREQ_DIV
flag is no more used, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove CONFIG_CMD_CACHE from include/configs/stm32f746-disco.h
and enable it in stm32f746-disco_defconfig
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable instruction and data caches.
Fix boot_sd command as since commit d409c96216 ("armv7m: disable
icache before linux booting"), instruction cache is automatically
disable before linux booting. "icache off" from boot_sd command
becomes useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit aa5e3e22f4 ("board: stm32: switch to DM STM32 timer")
SYS_CLK_FREQ is useless, remove it from stm32f4 and stm32f7 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use gd->bd->bi_dram[0].start initialized from DT instead of using
hardcoded CONFIG_SYS_SDRAM_BASE from config file.
Remove unused CONFIG_SYS_RAM_BASE and CONFIG_SYS_SDRAM_BASE defines.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case the slow clock is not properly configured, the UTMI clock
cannot lock the PLL, because UPLLCOUNT will "wait X slow clock cycles".
In this case U-boot will loop indefinitely.
Added a timeout in this case, to start U-boot even if UTMI clock is
not enabled, so the user can use different media if needed, or investigate.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Move some configuration #defines that do not apply to other bcmstb
boards from bcmstb.h to bcm7445.h.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Move the contents of prior_stage.h into bcmstb.h to prevent a build
failure when bcmstb.h is #include'ed before the asm/arch symbolic link
is present.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
If CONFIG_DEBUG_UART is enabled, correctly initialize
the debug uart before console is initialized to debug
early boot problems in SPL.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
In spl_gen5's board_init_f(), gd->malloc_base is manually assigned
at the end of the function to point to sdram. This code is outdated
as by now, the heap is switched to sdram by the common function
spl_relocate_stack_gd() if the appropriate defines are set.
As it was, the value assigned manually was directly overwritten by
this common code, so remove the manual assignment.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
There were NULL pointers dereferenced because DM was used
too early without correct initialization:
- malloc_simple returned NULL when called from preloader_console_init()
because gd->malloc_limit was 0
- uclass_add dereferenced gd->uclass_root members which were NULL because
dm_init (or one of its relatives) has not been called.
All this is fixed by calling spl_early_init before calling
preloader_console_init.
This fixes commit 73172753f4 ("ARM: socfpga: Convert to DM serial")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
"default" lines in Kconfig are processed in order, the first hit will
stop considering subsequent lines. In the case of the DRAM_ODT_EN symbol
that means that everything following the first two lines will never be
checked:
------------
config DRAM_ODT_EN
bool "sunxi dram odt enable"
default n if !MACH_SUN8I_A23
default y if MACH_SUN8I_A23
default y if MACH_SUN8I_R40
default y if MACH_SUN50I
------------
Assuming that the "default y" for the A64 and the R40 were a deliberate
choice, fix the Kconfig stanza to take this into account.
Also remove the now redundant lines from the respective defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[jagan: droped 'default n' on original change]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # A64, R40
Tested-by: Chen-Yu Tsai <wens@csie.org> # A23
Update all A83T devicetree dtsi and dtsi files from Linux-v4.18-rc3
with below commit:
commit 221cb9fd2ee3042689fe0e6613d0f34eb46a5af6
Author: Mylène Josserand <mylene.josserand@bootlin.com>
Date: Fri May 4 21:05:44 2018 +0200
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
Note: bananapi-m3 and cubietruck-plus board dts files has
usb_otg enabled in U-Boot which were not present in Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add a driver for the Xilinx LogiCORE DisplayPort IP core, which is a
pure DP transmitter core for Xiling FPGA (no display capabilities).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The entries of Makefiles should be sorted, which is not the case in the
video driver Makefile.
Sort the entries alphabetically as far as this makes sense.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Travis CI now supports giving jobs an explicit name. Do this for all jobs.
This allows more direct control over jobs names than the previous
automatic or implicit naming based on the environment variables or script
text.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
[trini: Update names for jobs added/changed since posting]
Signed-off-by: Tom Rini <trini@konsulko.com>
This update adds PPC64 ELF V1 ABI support to bootelf for both the
program header and section header options. Elf64 support was already
present for the program header option, but it was not handling the
PPC64 ELF V1 ABI case. For the PPC64 ELF V1 ABI, the e_entry field of
the elf header must be treated as function descriptor pointer instead
of a function address. The first doubleword of the function descriptor
is the function's entry address.
Signed-off-by: Rob Bracero <robbracero@gmail.com>
[trini: Fix whitespace issues]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fixup the Linux FDT with the detection of onboard DRAM as
provided by SBL (Secondary boot loader) by reading
the shared-memory region.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Underlying API should already print some meaningful error message, so
this one is just brings more noise. E.g. we can see log like this:
MMC: no card present
** Bad device mmc 0 **
Obviously, second error message is unwanted. Let's only print it in case
when DEBUG is defined to keep log short and clear.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
"Failed" error message from env_load() only clutters the log with
unnecessary details, as we already have all needed warnings by that
time. Example:
Loading Environment from FAT... MMC: no card present
** Bad device mmc 0 **
Failed (-5)
Let's only print it in case when DEBUG is defined to keep log clear.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fixes the following checkstyle warning:
WARNING: Missing a blank line after declarations
+ int tmp = smbios_write_funcs[i]((ulong *)&addr, handle++);
+ max_struct_size = max(max_struct_size, tmp);
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes the following chechpatch -f error:
ERROR: "(foo*)" should be "(foo *)"
+ strncpy((char*)t->uuid, serial_str, sizeof(t->uuid));
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Compressed images should have their compression property
set to "none" if U-Boot should leave them compressed.
This is especially the case for compressed ramdisks that
should be uncompressed by the kernel only.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
For these boards, the GPMC timings are more determined by
processor speed/type than the NAND/PoP memory. This code
is never invoked, so disable the config option, so it doesn't
take the time to compile it in.
Signed-off-by: Adam Ford <aford173@gmail.com>
Create separate html pages for linker lists, the serial subsystem,
and the EFI subsystem.
Add a table of content.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The console index for SPL should be 1 not 3 in order to see text during
SPL.
Fixes: 6f6b7cfa89 ("Convert all of CONFIG_CONS_INDEX to Kconfig")
Signed-off-by: Adam Ford <aford173@gmail.com>
Program Central Security Unit (CSU) to grant access to USB 2.0
controller.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
This is a fix made for the fsl_ifc_nand driver on linux kernel by
Pavel Machek and is applied to uboot. It is currently on applied on
linux-mtd.
https://patchwork.kernel.org/patch/9758117/
IFC always raises ECC errors on erased pages. It is only ignored when
the buffer is checked for all 0xFF by is_blank(). The problem is a
single bitflip will cause is_blank() and then mtd_read to fail. The fix
makes use of nand_check_erased_ecc_chunk() to check for empty pages
instead of is_blank(). This also makes sure that reads are made at ECC
page size granularity to get a proper bitflip count. If the number of
bitflips does not exceed the ECC strength, the page is considered empty
and the bitflips will be corrected when data is sent to the higher
layers (e.g. ubi).
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Cc: Pavel Machek <pavel@denx.de>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Pavel Machek <pavel@denx.de>
[Kurt: Replaced dev_err by printf due to compiler warnings]
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of qman portals and the required device
tree fixups. Also fix an endiness issue in portal setup code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QMAN_BAR{E} register setup was disabled on ARM platforms, however the
register does need to be set. Enable the code also on ARMs and fix the
CONFIG_SYS_QMAN_MEM_PHYS define to the correct value so that the newly
enabled code works.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The QMan IP block in this SoC is version 3.2 so advertise
this in the SoC configuration header.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
sata_probe returns 1 for failure, so don't checkout for < 0
fixes: f19f1ecb60 dm: sata: Support driver model with the 'sata' command
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Initialize the led with the default state defined in device tree
in board_init and solve issue with test for led default state.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Initialize the led with the default state defined in device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch save common LED property "default-state" value
in post bind of LED uclass.
The configuration for this default state is only performed when
led_default_state() is called;
It can be called in your board_init()
or it could added in init_sequence_r[] in future.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This reverts commit bc882f5d5c.
because this patch adds the probe of LED driver during the
binding phasis. It is not allowed in driver model because
the drivers (clock, pincontrol) needed by the LED driver can
be also probed before the binding of all the device and
it is a source of problems.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch add the 4 LED available on the ED1 board and activated
gpio led driver.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
sourcing of sub directiory kconfig files are not in
proper order, so keep them in ascending order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
It might be useful for user to see some human-readable root cause
message in addition to "configuration failed" message, so that the issue
can be fixed quickly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
In case of error in dfu_init_env_entities(), env_bkp will leak. Fix it
by providing single return path.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Commit 5d8fae7916 ("dfu: avoid memory leak") brings a regression which
described below. This patch is effectively reverting that commit, adding
corresponding comment to avoid such regressions in future.
In case of error in dfu_config_entities(), it frees "dfu" array, which
leads to "data abort" in dfu_free_entities(), which tries to free the
same array (and even tries to access it from linked list first). The
issue occurs e.g. when partition table on device does not match
$dfu_alt_info layout:
=> dfu 0 mmc 1
Couldn't find part #2 on mmc device #1
DFU entities configuration failed!
data abort
To fix this issue, do not free "dfu" array in dfu_config_entities(). It
will be freed later in dfu_free_entities().
Tested on BeagleBone Black (where this regression was originally found).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
As well as in K_FW_LBA_READ_10 and K_FW_LBA_ERASE_10 take device's
block size from f_rkusb->desc->blksz instead of the fixed 512 bytes.
Keep original behaviour of retry probing assigned block device on
every host request to manage late SDCard plugs.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
While downloading or uploading megabytes of data we had thousands of
printf in console like:
transfer 0x10000 bytes done
OR
Uploading 0x1000 bytes
This because transfers are chunked and there is no way on target
side to know the overall transfer size (to print one string per
overall transfer).
All these prints on serial console do slow down significantly the
transfer and does not offer a significant information to the
developer: rkdeveloptool and Rockchip original tool do use small
chunks read/writes on big transfers. This allows on workstation
to print percentage of transfer complete and as well offers to
developer the information about: transfer is running OK.
On error, either the percentage will stop or an error will be shown
on workstation console.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chip Version is a string saved in BOOTROM address space Little Endian.
Ex for rk3288: 0x33323041 0x32303134 0x30383133 0x56323030
which brings: 320A20140813V200
Note that memory version do invert MSB/LSB so printing the char
buffer would show: A02341023180002V
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Two consecutive rockusb_tx_write without waiting for request complete
do results in transfer reset of first request and thus no or incomplete
data transfer. This because rockusb_tx_write do use just one USB request
to keep serialization.
So calls like:
rockusb_tx_write_str(emmc_id);
rockusb_tx_write_csw(cbw->tag, cbw->data_transfer_length, CSW_GOOD);
was succeeding only when DEBUG was defined because the time spent
printing debug info was enough for transfer to complete.
This patch fixes the issue adding a simple request complete handler
called rockusb_tx_write_csw to be set as complete handler of in_req
when sending back simple payload + CSW replies to commands.
This new handler will always send CSW_GOOD replies because in case
of error the command callback itself must send back an error CSW as
unique reply to command.
This patch fixes execution of:
$ rkdeveloptool rfi
when DEBUG is not defined.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
After the commit 6aae84769a ("gadget: f_thor: Fix memory leaks of
usb request and its buffer"), there is hang-up with ctrl-c in some
udc. It is because req of out_ep is freed before out_ep is disabled.
Fix hang-up with ctrl-c by disabling ep before free req of the ep.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The 16 char ethernet name size is inadequate to hold the name of ethernet
name "DPMAC17@rgmii-id", which is a valid name in LX2160AQDS/LX2160ARDB.
Therefore, increase the name string size to 20 chars.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Ioana Ciocoi Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The ethernet name should be within the ETH_NAME_LEN, as this
is the buffer space allocated to ethernet name.
Otherwise, this causes buffer overflow.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Most FSL PCIe controllers expects 333 MHz PCI reference clock.
This clock is derived from the CCB but in many cases the ref.
clock is not 333 MHz and a divisor needs to be configured.
This adds PEX_CCB_DIV #define which can be defined for each
type of CPU/platform.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A recent rename of the function did not rename the test file. Fix this.
Fixes: 12308b128f (lib: fdtdec: Rename routine fdtdec_setup_memory_size())
Signed-off-by: Simon Glass <sjg@chromium.org>
The enhanced pylibfdt support in U-Boot needed for binman was a
placeholder while upstreaming of this work continued. This is now
complete, so bring in the changes and update the tools as needed.
There are quite a few changes since we decided to split the
implementation into three fdt classes instead of two.
The Fdt.del_node() method was unfortunately missed in this process and
will be dealt with later. It exists in U-Boot but not upstream.
Further syncing of libfdt probably needs to wait until we assess the
code-size impact of all the new checking code on SPL and possibly provide
a way to disable it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add several PCI capability and extended capability ID registers
in the swap_case driver, so that we can add test case for
dm_pci_find_capability() and dm_pci_find_ext_capability().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces two new APIs dm_pci_find_capability() and
dm_pci_find_ext_capability() to get PCI capability address and
PCI express extended capability address for a given PCI device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently we don't have a complete list of capability and extended
capability ids. This adds them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the Sandbox test configuration, PCI bus#0 only has static devices
while bus#1 only has dynamic devices. Create a bus#2 that has both
types of devices and test such.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have "struct sandbox_pci_priv" in pci_sandbox driver. To avoid
confusion, rename the emul's priv to "struct sandbox_pci_emul_priv".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With struct pci_device_id, it's possible to pass a driver data for
bound driver to use. This adds a test case for this functionality.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present we have two PCI buses in the test configuration. Both
buses have static device-tree config devices. Now we switch the
2nd bus to use dynamic PCI devices for testing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a U_BOOT_PCI_DEVICE() declaration to the swap_case driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct driver data comes from the matching 'id' instead of
'find_id' in pci_find_and_bind_driver().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the newly added test cases for PCI configuration access, we get:
=> ut dm pci_busdev
Test: dm_test_pci_busdev: pci.c
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Test: dm_test_pci_busdev: pci.c (flat tree)
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Failures: 2
The bug only shows up when bus number is not equal to zero. This is
caused by the plain find_devfn parameter is passed to function call
pci_bus_find_devfn(), inside which find_devfn is compared to devfn
in the device's pplat structure. However pplat->devfn does not carry
the bus number. Fix this by passing find_devfn with bus number masked.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far we missed the testing for PCI configuration space access.
This adds tests for it, as well as removing some redundant asserts.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far there is only one PCI host controller in the sandbox test
configuration. This is normally the case for x86, but it can be
common on other architectures like ARM/PPC to have more than one
PCI host controller in the system.
This updates the case to cover such scenario.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the newly added testing of more than one device, we get:
=> ut dm pci_swapcase
Test: dm_test_pci_swapcase: pci.c
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Test: dm_test_pci_swapcase: pci.c (flat tree)
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Failures: 2
The failure only happens on the 2nd swap_case device on the PCI bus.
The case passes on the 1st device.
It turns out the swap_case driver does not emulate bit#0 in BAR
registers as a read-only bit. This corrects the implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's quite common to have more than one device on the same PCI bus.
This updates the test case to test such scenario.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The check on uclass_get_device() and device_active() is unnecessary
as the follow-up test operations will implicitly probe the driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The flag to control whether to scan multi-function device during
enumeration should be cleared at the beginning of each iteration
if the device's function number equals to zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently only devfn is extracted in child_post_bind(). Now that
we have the live-tree version API to look up PCI vendor and device
id from the compatible string, let's extract and save them too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't have the live-tree version of fdtdec_get_pci_vendev().
This adds the API.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Correct typos in the comment block of uclass_first/next_device_check().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These macros should not be put in the generic pci.h header file.
Since they are not referenced anywhere, remove them completely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This add the initial support of the broadcom reference
board bcm968380gerg with a bcm68380 SoC.
This board has 512 MB of RAM, 128 MB of flash (nand),
2 USB port, 1 UART, 4 ethernet ports and BCM43217 (wifi).
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This adds the initial support of the Broadcom BCM6838 SoC familly,
only cpu, dram, uart and leds are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
In ft_fixup_enet_phy_connect_type(), use strlen() instead of sizeof()
on the pointer result of phy_string_for_interface(). sizeof() was
returning the size of the pointer (4 bytes), resulting in the
phy-connection-type being set to "rgmi" rather than "rgmii-id".
Signed-off-by: Brendan Shanks <brendan.shanks@teradek.com>
Cc: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add command "boot_bank X" to switch the boot bank to either 1 or 2.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Xilinx fixes for v2018.09-rc2
xilinx:
- Add support for zybo z7 and ultra96
- Tune zynq and zynqmp mini configurations
- Move SYS_MALLOC_LEN to Kconfig
fdt
- make static funcs
gpio:
- Fix soft gpio driver
- Fix Zynq gpio driver by using platdata
microblaze:
- Fix Kconfig entry
spi
- Move ISSI to Kconfig
Add a flash node to fix the detection of the memory IC.
With the changes introduced with commit 8fee8845e7
("enf_sf: reuse setup_flash_device instead of open coding it")
the SPI speed is now read from device-tree or a default value
is applied. This replaced the old behavior of setting the
SPI speed to CONFIG_ENV_SPI_MAX_HZ.
As this board didn't have a flash node, the default value
was applied to the SPI speed, producing an error when probing
the flash memory (speed too slow).
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for reading label property from DT and set up bank name
based on that. If label property is not present full device node name is
used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
.set_value functions have no specified return value and gpio_uclass is
not working with it too. But this patch is returning 0 to be in sync
with others DM gpio drivers.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Reading registers for finding out output value is not working because
input value is read instead in case of tristate.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
These functions are only called in this file that's why make them static
to keep static analysers happy.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Set a value before changing gpio direction. This will ensure that the
old value is not propagated when direction has changed but new value is
not written yet.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
CONFIG_MTD_DEVICE is required for the mtdparts command and but it is missing from the mvebu_armada-37xx.h
CONFIG_MTD_PARTITIONS is needed for the ubi support. Some of the Marvell based devices may require this as well.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Stefan Roese <sr@denx.de>
When kwboot is attached to a terminal which disappears such as one
connected via an unplugged USB cable, read() returns 0, making kwboot
loop until a key is pressed in the terminal. The only case where read()
may return 0 here is when the terminal is closed anyway, so let's
properly handle this one and report is similar to other errors.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 84899e2 ("tools/kwboot: Sync with latest barebox version to
support Armada XP") accidently broke the terminal-only mode (-t) by
removing the test on the bootmsg. Thus even when trying to use kwboot
as a plain terminal, it asks to reboot the target.
This commit simply reintroduces the lost test so that it is possible
again to use kwboot to attach to the target system's console.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GP24 and SBx81GT24 cards
cards collectively referred to as SBx81LIFXCAT in u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This is required so SPL and u-boot can boot from spi
flash devices that use the dm drivers.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use -u-boot.dtsi]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The same pinctrl node appears in the solidrun-microsom dtsi. Use that
instead.
Cc: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes changes so the u-boot dts file is structured more
similar to the mainline linux dtsi file. It provides a minimal
common dts that can work for most boards based on the ClearFog
platform. Ethernet support is only supported for eth0 however
all devices are left enabled so u-boot can generate and
provide mac addresses for all of the network interfaces.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on recent changes]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Use hardware description from the recently introduced microsom .dtsi
file to reduce duplication.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Dennis Gilmore <dennis@ausil.us>
Tested-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the "spi-flash" compatible string so that the generic sf_probe
driver can probe the SPI flash on the SolidRun SOM.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that there is DM support in the RTC_MV driver update board configs
to use it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
To aid in migrating CONFIG_RTC_MV to Kconfig move the definition of it
from mv-plug-common.h to the board config headers that nest it.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the PCA9646 support, which is 2-wire bus switch and buffered 4-channel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This allows selection of the boot device at build time without source
code modification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The kwboot utility can use the generated image to boot mvebu SoCs from
UART.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the gdsys Controlcenter DC specific build time kwbimage.cfg
generation code into the mach-mvebu/ directory to be shared by all 32bit
mvebu platforms.
Remove board specific kwbimage.cfg files, and use the generated one
instead. These files are all identical, with two exceptions. Clearfog
and Helios4 use the sdio boot device, whereas all others use spi. Update
the defconfigs for the exceptional boards to generate the same
kwbimage.cfg as before.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use MVEBU_SPL_BOOT_DEVICE_* to select between SPI and MMC, instead of
board specific symbols. This commit enables the boot device selection
menu to all mvebu platforms, but it is only effective on Turris Omnia
and gdsys Controlcenter DC platforms. A following commit will enable
boot selection for other platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Use generic mvebu Kconfig symbols like all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
u-boot-spl.bin and u-boot-spl-dtb.bin are identical when building the
turris_omnia_defconfig. This commit makes Turris Omnia consistent with
all other mvebu boards.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This is to test power_domain_on in device_probe.
If the device has a power-domain property, enable it
when probe the device. So add the test to check
whether it is powered on or not.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add dummy functions when CONFIG_POWER_DOMAIN not defined.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Avnet Ultra96 is rebranded Xilinx zcu100 revC/D. Add new defconfig files
and point to origin internal board name.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves the the config SYS_MALLOC_LEN to
Kconfig. It will be just for Zynq arch and to do
will be for all other archs.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch used platdata structure instead of priv for storing static
information read from DT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This issue is reported by kconfiglib:
warning: style: quotes recommended around default value for string
symbol XILINX_MICROBLAZE0_HW_VER (defined at
board/xilinx/microblaze-generic/Kconfig:37)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini cse NOR configuration is running without PL that's why there is no
reason to enable clock to PL.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing clocks property with fix clock-names property to be aligned
with emmc0 configuration and binding doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to have the same setting in subsequent config if we
can have it only once in shared.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit enables support for Exynos Designware MMC driver based on DM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
By convention for DM_MMC the host->priv is used to store struct udevice
*dev pointer.
Unfortunately, the legacy Exynos DW MMC code uses this field to
store pointer to dwmci_exynos_priv_data struct
Hence, we do need to get data in other way - namely by using container_of
when host pointer is present.
In this way the sdr_timing data is properly accessed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is necessary to allow booting the Odroid XU3 from SD card
after enabling the DM_MMC support.
After this change the SD card mmc IP block is correctly enumerated as mmc2
(and not as mmc1 as in the legacy code).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit adjusts the autoboot.cmd file to use ${mmcbootdev} instead of
hardcoded value 0.
This is necessary to allow booting this board from the SD card.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Exynos5422 is solely using DW MMC IP block to support eMMC/SD devices,
hence the SDHCI code doesn't need to be compiled it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit prevents memory leak when this function is used with DM_MMC
as the struct dwmci_exynos_priv_data is already allocated by DM.
It is necessary for NON DM aware devices to allocate this struct first.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As cd-inverted property is no more used by arm_pl180_mmci driver,
remove it. Update cd-gpios active level accordingly.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add missing clk_free() call in case of failure
when enabling the clock.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
CONFIG_BLK config flag becomes mandatory, enable it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
1947c2d2a0 introduces cache line flushes for the bootcounter, but if
the start address is not aligned then the flush causes warnings of
the form:
CACHE: Misaligned operation at range [4030b7fc, 4030b83c]
Align both the start and end of the buffer (possibly crossing multiple
lines).
Fixes: 1947c2d2a0 ("bootcount: flush after storing the bootcounter")
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Even though the exception vector table is a fundamental part of the ARM
architecture, U-Boot mostly does not make real use of it, except when
crash dumping. But having it in takes up quite some space, partly due to
the architectural alignment requirement of 2KB. Since we don't take special
care of that, the compiler adds a more or less random amount of padding
space, which increases the image size quite a bit, especially for the SPL.
On a typical Allwinner build this is around 1.5KB of padding, plus 1KB
for the vector table (mostly padding space again), then some extra code
to do the actual handling. This amounts to almost 10% of the maximum image
size, which is quite a lot for a pure debugging feature.
Add a Kconfig symbol to allow the exception vector table to be left out
of the build for the SPL.
For now this is "default y" for everyone, but specific defconfigs,
platforms or .config files can opt out here at will, to mitigate the code
size pressure we see for some SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The arm64 exception handling code is quite big, mostly due to
architectural alignment requirements. Each exception entry spans 32
instructions, which sounds generous, but is too small to fit all of the
save/branch/restore code in there. So at the moment we use only four
instructions, branching into shared save and restore routines.
To not leave the space for those remaining 28 instructions wasted, let's
split the save and restore routines and stuff them into the gaps.
This saves about 250 bytes of code, which is helpful for those tight
SPLs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.
Let's consoldate this all into one place, and remove them from the
individual boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds support for STMicroelectronics STM32 ADC (analog to
digital converter). It's originally based on Linux kernel v4.18-rcs
drivers/iio/adc/stm32-adc*. It's composed of:
- core driver (UCLASS_SIMPLE_BUS) manages common resources (clk, regu).
- child drivers (UCLASS_ADC) declare each ADC, channels and handle
conversions.
This driver currently supports STM32H7 and STM32MP1 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds documentation of device tree bindings for the STM32 ADC.
It's based on linux-v4.18-rc* dt-bindings, at the time of writing:
- Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
device_get_supply_regulator() only needs to be called once.
But each time there's call to adc_vxx_value() for instance, it calls
adc_vxx_platdata_update() -> device_get_supply_regulator().
So, move device_get_supply_regulator() to pre_probe() routine.
This also allows vdd_supply/vss_supply to be provided directly from
uc_pdata, e.g dt-binding variant like stm32-adc provide its own
'vref-supply'.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_valid() to check for optional clocks are valid.
Call clk_valid() in test/dm/clk.c and add relevant test routine to
sandbox clk tests.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "Beaglebone Enhanced" by Sancloud is based on the Beaglebone Black,
but with the following differences:
* Gigabit capable PHY
* Extra USB hub, optional i2c control
* lps3331ap barometer connected over i2c
* MPU6050 6 axis MEMS accelerometer/gyro connected over i2c
* 1GiB DDR3 RAM
* RTL8723 Wifi/Bluetooth connected over USB
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add spi driver for sun4i, sun5i and sun7i SoCs. The driver is
adapted from mailine kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Align the size of the carveout region to 2M. This ensures that the size
can be accurately represented by an LPAE page table that uses sections.
This solves a bug (hang at boot time soon after printing the DRAM size)
that only shows up when the following two commits are merged together:
d32e86bde8 ARM: HYP/non-sec: enable ARMV7_LPAE if HYP mode is supported
6e584e633d ARM: tegra: avoid using secure carveout RAM
Cc: Mark Kettenis <kettenis@openbsd.org>
Cc: Alexander Graf <agraf@suse.de>
Acked-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
At present this function takes a filename, but it is better to use an Fdt
object so that the caller can control this, perhaps obtainint the device
tree from a bytearray. Update the method accordingly and also fix a
confusing parameter name.
Signed-off-by: Simon Glass <sjg@chromium.org>
This property has been changed to 'offset'. To help downstream users who
might still be using 'pos', add a check that this is not used by mistake.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name is too generic for its purpose and is therefore
confusing. It actually only applies to blobs, so rename it to indicate
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the map only shows the offset and size for each region. The
image position provides the actual position of each entry in the image,
regardless of the section hierarchy.
Add the image position to the map.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for U-Boot's TPL and TPL device tree. Also fix a few comments
in the other device-tree entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function which can decode a property containing a list of phandles.
This is useful for finding nodes linked to a property. Also provide a way
to look up a single phandle and get the Fdt object from a Node.
Signed-off-by: Simon Glass <sjg@chromium.org>
When this fails it is useful to see the current directory, since U-Boot's
build system will typically change into the output directory during the
build. Add this information to the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tests use the 'test_result' feature to return a predetermined command
result for particular commands. The avoids needing to have the real
command available just to run a test. It works by calling the function
provided by the test, to get the value.
However sometimes the test does need to run the real command. Allow it to
fall back to do this when the function does not return a result.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to have an area of the image which is all zeroes,
or all 0xff. This can often be achieved by padding the size of an an
existing entry and setting the pad byte for an entry or image.
But it is useful to have an explicit means of adding blocks of repeating
data to the image. Add a 'fill' entry type to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an entry type which can hold a Chrome OS EC.
To make this work a new entry type is created, which supports getting a
blob filename from the command line.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an entry which can hold an FMAP region as used by flashrom, an
open-source flashing tool used on Linux x86 machines. This provides a
simplified non-hierarchical view of the entries in the image and has a
signature at the start to allow flashrom to find it in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a new README containing documentation for the entry types supported
by binman. This provides an easy reference in one place. It is
automatically generated from the source-code documentation.
Add a reference to this from the binman README.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binman supports quite a number of different entries now. The operation of
these is not always obvious but at present the source code is the only
reference for understanding how an entry works.
Add a way to create documentation (from the source code) which can be put
in a new 'README.entries' file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only the more complex entries are documented. It is useful to
have documentation for all entries in one place.
As a first step, add and expand the documentation to cover all entries.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present binman needs libfdt.py to be available before it will do
anything, even print help. Import those modules later to avoid this, as it
is bad practice to fail to even show help on startup.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to able to write an identifying string to the image within an
entry. Add a 'text' entry type to handle this. The actual text is
typically passed to binman on the command line. The text is not itself
nul-terminated but this can be achieved if required by setting the size of
the entry to something larger than the text.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to pass binman the value of an entry property from
the command line. For example some entries need access to files and it is
not always convenient to put these filenames in the image definition
(device tree).
Add a -a option which can be used like this:
-a<prop>=<value>
where
<prop> is the property to set
<value> is the value to set it to
Signed-off-by: Simon Glass <sjg@chromium.org>
At present each entry has an offset within its parent section. This is
useful for figuring out how entries relate to one another. However it
is sometimes necessary to locate an entry within an image, regardless
of which sections it is nested inside.
Add a new 'image-pos' property to provide this information. Also add
some documentation for the -u option binman provides, which updates the
device tree with final entry information.
Since the image position is a better symbol to use for the position of
U-Boot as obtained by SPL, update the SPL symbols to use this instead of
offset, which might be incorrect if hierarchical sections are used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the .map file produced for each image does not include the
overall image size. This is useful information.
Update the code to generate it in the .map file as well as the updated
FDT. Also fix a few comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few lines are commented out and can be removed. Also fix return-value
docs for _DoReadFile() and _DoReadFileDtb().
Signed-off-by: Simon Glass <sjg@chromium.org>
The purpose of some of the tests is not obvious from the function names.
Add a few comments to help with understanding.
Signed-off-by: Simon Glass <sjg@chromium.org>
After some thought, I believe there is an unfortunate naming flaw in
binman. Entries have a position and size, but now that we support
hierarchical sections it is unclear whether a position should be an
absolute position within the image, or a relative position within its
parent section.
At present 'position' actually means the relative position. This indicates
a need for an 'image position' for code that wants to find the location of
an entry without having to do calculations back through parents to
discover this image position.
A better name for the current 'position' or 'pos' is 'offset'. It is not
always an absolute position, but it is always an offset from its parent
offset.
It is unfortunate to rename this concept now, 18 months after binman was
introduced. However I believe it is the right thing to do. The impact is
mostly limited to binman itself and a few changes to in-tree users to
binman:
tegra
sunxi
x86
The change makes old binman definitions (e.g. downstream or out-of-tree)
incompatible if they use the 'pos = <...>' property. Later work will
adjust binman to generate an error when it is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this test assumes that the symbols are returned in address
order. However, objdump can list symbols in any order and dictionaries do
not guarantee any particular order when iterating through item.
Update elf.GetSymbols() to return an OrderedDict, sorted by address, to
avoid any problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
That's a set of prety minor changes and fixes for ARC.
Among them:
* Improvement in CREG GPIO driver used on ARC dev boards
that allow us to re-use the driver for SPI's chip select
* Enable SPI-flsh on AXS10x boards which allows to update
U-Boot binary that gets loaded by boot-ROM
* Fix accommodating always utilized unaligned access by
GCC for ARC starting from 8.1.0
Drop the DM_I2C dependency, as the library only implements
the parsing of EDID data and doesn't depend on any driver
One user of this library, the i2c command, implements
support for legacy and DM I2C drivers
Tested on a Zynq board, whose I2C driver is not ported
yet to DM
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
The openrd platforms are currently orphaned, and are constantly on-edge
or overflowing their binary limit. Exclude them from travis for now.
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Update the MAINTAINERS file to list Otavio Salvador as the maintainer
for this board.
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
The patch "dm: Change CMD_DM enabling"
(sha1: 08a00cba06) was incorrectly updated
and PICO_IMX7D is missing imply CMD_DM and WARP7 has it twice.
This patch is fixing it.
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was an EHCI endian accessor issue. Now it's fixed by commit
9829ce2ff2 ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit e6a727fffe ("powerpc/T104xRDB: Fix
endian access issue on EHCI intinalization"). On T104x platform,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
There was an EHCI endian accessor issue. Now it's fixed by commit
9829ce2ff2 ("usb: ehci: Fix accessors for big-endian platforms and
descriptors"). Revert commit 0f2296bab1 ("powerpc/p1_p2_rdb_pc:
Fix endian access issue on EHCI intinalization"). On P1 P2 platforms,
USB EHCI register use little endian.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
OrangePi One Plus is Allwinner H6 based open-source SBC,
which support:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB LPDDR3 RAM
- AXP805 PMIC
- 1Gbps GMAC via RTL8211
- USB 2.0 Host, OTG
- HDMI port
- 5V/2A DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Return the error code of the set_features function only if
the error code is not ENOTSUPP. Otherwise, if this function
is not supported, it will return and fail to initialize the
NAND.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Convert the EINVAL error into ENOTSUPP when the GET/SET_FEATURES
is not supported.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Only H3 and H5 have 4 PHYS so restrict rst_mask only for them
by checking PHY id as 3 and update the proper bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.
Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes when a monitor without EDID information is plugged, the DE2
won't be probed (because of lack of timing information), but the HDMI
node is probed, thus a SimpleFB node with invalid information will be
populated.
Also detect whether DE2 is probed when creating SimpleFB node.
Fixes: be5b96f0e4 ("sunxi: setup simplefb for Allwinner DE2")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Pine H64 is a SBC with Allwinner H6 SoC produced by Pine64. It features
1GiB/2GiB/4GiB(3GiB usable) DRAM, two USB 2.0 ports, one USB 3.0 port
and a mPCIE slot.
Add support for it.
The device tree is from Linux next-20180720.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner H6 is a new SoC from Allwinner features USB3 and PCIe
interfaces.
This patch adds support for it.
The corresponding DTSI file, from Linux next-20180720, is also
introduced.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC comes with a set of new DRAM controller+PHY combo.
Both the controller and the PHY seem to be originate from DesignWare,
and are similar to the ones in ZynqMP SoCs.
This commit introduces an initial DRAM driver for H6, which contains
only LPDDR3 support. The currently known SBCs with H6 all come with
LPDDR3 memory, including Pine H64 and several Orange Pi's.
The BSP DRAM initialization code is closed source and violates GPL. Code
in this commit is written by experimenting, referring the code/document
of other users of the IPs (mainly the ZynqMP, as it's the only found PHY
reference) and disassebling the BSP blob.
Thanks for Jernej Skrabec for review and fix some issues in this driver
(including the most critical one which made it to work), and rewrite
some code from register dump!
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
On the new Allwinner H6 SoC, the SRAM A2 address (SPL load address) is
at 0x20000, which is different with any old Allwinner SoCs.
Add SPL position and size configuration for this.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
H6 has different SRAM A2 address, so the ATF load address is also
different.
Add judgment code to sunxi 64-bit FIT generation script. It will judge
the SoC by the device tree's name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The Allwinner H6 SoC come with a totally new memory map.
Add basical definition of the new memory map into a header file, and let
the cpu.h header include it in the situation of H6.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The new Allwinner H6 SoC has its SRAM A1 at neither 0x0 nor 0x10000, but
it's at 0x20000. Thus the SUNXI_HIGH_SRAM option needs to be refactored
to support this new configuration.
Change it to SUNXI_SRAM_ADDRESS, which holds the real address of SRAM
A1 in the memory map.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Banana Pi M2 Ultra and M2 Berry are very similar boards. SATA can be
enabled exactly the same as for M2 Ultra introduced in
commit daa8b75a55 ("sunxi: enable SATA on Banana Pi M2 Ultra").
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since U-Boot tools are being built anyways it's much nicer
to use them instead of relying on some of them bein installed
on build host (which might easily not be the case).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
AXS10x boards have preloader that reads SPI flash pages and searches
special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
AXS10x boards have n25q512 spi flash IC, so add corresponding
nodes to device tree and enaple corresponding options in
defconfig.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
CREG GPIO is a driver for weird soc-specific output ports, which are
controlled by some fields in memory mapped register.
Example:
31 9 7 5 0 < bit number
| | | | |
[ not used | gpio-1 | gpio-0 | <-shift-> ] < 32 bit register
^ ^
| |
write 0x2 == set output to "1" (activate)
write 0x3 == set output to "0" (deactivate)
As of tooday we only support fixed (hardcoded) bit per gpio line,
activate / deactivatei and shift values. Fix that by read them from
device tree to be able to use this driver for other boards.
Remove "hsdk" prefix from compatible string as this driver can be
used with different boards like HSDK, AXS101, AXS103, etc.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Given 0dc1bfb730 ("fs: fat: cannot write to subdirectories") we have
changed how the FAT code works from creating the illegal file "./file"
and instead rejecting the path. The correct behavior would be to write
"file" to "." but not writing an illegal file is a step in the right
direction. For now, update the expected output to account for the
failure.
Signed-off-by: Tom Rini <trini@konsulko.com>
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Trivial Kconfig cleanup. Use tabs instead of spaces and every Kconfig
entry should be separated by newline.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
When called with ENVOP_SAVE, env_get_location() only returns the
gd->env_load_location variable without actually checking for
the environment location and priority.
This behaviour causes env_save() to fall into an infinite loop when
the low-level drv->save() call fails.
The env_save() function should not loop through the environment
location list but it should save the environment into the location
stored in gd->env_load_location by the last env_load() call.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Remove additional trailing whitespaces in prompt reported by kconfiglib:
warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
This reverts commit 5e5745465c.
The reverted commit didn't support the scenario where there are less
DRAM banks in U-Boot than in Linux.
Also, it didn't introduce any new functionality, only limitaion.
User could just increase MEMORY_BANKS_MAX if it's too small.
Reviewed-by: Simon Glass <sjg@chromium.org>
With the pending requirement for CONFIG_BLK, this patch removes
the USB_STORAGE option which assumes that DM_USB is enabled, but isn't
yet available for the omap2340 musb glue among other issues. Once
the USB issues are resolved, a future patch can enable them again.
Signed-off-by: Adam Ford <aford173@gmail.com>
Now that TPMv1 and TPMv2 can be compiled at the same time, let's compile
them both with Sandbox as well as both drivers (and, it is already
implied in Kconfig: both commands).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
TPM_V1 was already compiled by default. Now that both can be compiled
at the same time, compiled them both by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While using the 'tpm' command should work on most cases, this test suite
only works with TPMv2 and since the work to make both versions build at
the same time, we might end up having both 'tpm' (TPMv1) and 'tpm2'
(TPMv2) commands available at the same time. Ensure this test suite
always use the right one.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
The TPM_DRIVER_SELECTED symbol was used in one of the initial series
about TPMv2 but its use has been dropped, making these selects
useless, remove them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Sandbox and the TPM stack are both selected, compile Sandbox TPM
driver by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The udevice given to the open() function of course must be opened,
not closed.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With some recent changes to relevant drivers here the openrd board
(openrd_client in this case) does not fit within its size constraint.
We can however drop the slightly extended baudrate table and then the
duplication of mtdparts/mtdids in the default environment. These
defaults are set in the environment by the 'mtdparts' command and
otherwise referenced throughout the code.
Signed-off-by: Tom Rini <trini@konsulko.com>
The default value with distro_bootcmd is 2 seconds, which is
reasonably fast, and provides a consistent experience across platforms
supporting distro_bootcmd.
The current bootdelay value of 0 seconds is a bit challenging to
interrupt when desired.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Enable distro_bootcmd for a standardized boot process across multiple
platforms.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding distro_bootcmd support bumps the default environment size over
4500. Increase to SZ_16K to allow for room to grow in the future.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replace non-standard variable names kerneladdr, initrdaddr and fdtaddr
with kernel_addr_r, ramdisk_addr_r and fdt_addr_r, as documented in
u-boot README.
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
fdt_fixup_mtdparts() calls mtdparts_init() and device_find(),
which are defined in cmd/mtdparts.c
The combination of FDT_FIXUP_PARTITIONS=y and CMD_MTDPARTS=n
emits the following link error:
common/fdt_support.c:903: undefined reference to `mtdparts_init'
common/fdt_support.c:914: undefined reference to `device_find'
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to this patch is fdtdec_setup_memory_banksize() incorrectly
ignoring the "status" field. This patch fixes that by testing the status
with fdtdec_get_is_enabled() before using a memory node.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previously the first three words in a git-mailrc alias entry could only
be separated by spaces. git-send-email and Mutt both allow arbitrary
whitespace here.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
patman's _ReadAliasFile only splits on spaces, not tabs, so the entries
for dinh and maxime weren't being recognised as valid. I'll fix patman
in a separate patch, but this makes all the entries consistent.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix warning when compiling tegra30-beaver/-apalis.dts with latest DTC:
"Warning (avoid_unnecessary_addr_size): /pci/pch@1f,0: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property"
Signed-off-by: Tom Warren <twarren@nvidia.com>
If a secure carveout exists, U-Boot cannot use that memory. Fix
carveout_size() to reflect this, and hence transitively fix
usable_ram_size_below_4g() and board_get_usable_ram_top(). This change
ensures that when U-Boot copies the secure monitor code to install it, the
copy target is not in-use for U-Boot code/data.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
When fixing up the DT to report PSCI support, explicitly enable the node.
DTs may ship with the node disabled in case a PSCI implementation is not
present, and expect any PSCI implementation to enable the node if they are
actually present.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enhance the PSCI DT editing code to allow setting a PSCI v0.2 compatible
value in the DT. The CONFIG_ option is added to the whitelist to match the
existing PSCI_1_0 option. While not adding new options to Kconfig isn't
ideal, I figure it's better to keep related options together.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a MON_MODE define for ARM's monitor mode. This can be used later by
a secure monitor to avoid hard-coding mode IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
RAM repair has a few pre-requisites:
1) PMIC power supply (rail) enabled.
2) PMC CRAIL power partition powered.
3) Fuse clock active (it's the default).
4) PLLP reshift branch enabled (it's the default, when PLLP is active).
RAM repair also only need run whenever specific partitions are powered
(main SoC and CCPLEX respectively); RAM repair does not need to be
triggered when any other partition changes state.
start_cpu() needs to be re-ordered slightly to match these requirements.
Note that C0NC and CE0 aren't required for RAM repair to
operate, but they also do no harm, so the entire of powerup_cpus() is
moved rather than splitting it up. The call to remove_cpu_resets() is
moved last to ensure that all other actions complete before releasing
reset; since the PMC power partitions are now enabled early, releasing
reset is what causes the CPUs to start executing code, and RAM repair must
complete before the CPU boots.
Note that this commit is the result of squashing a numbmer of commits
in NVIDIA's downstream L4T branch, hence the multiple signoffs below.
Signed-off-by: Bibek Basu <bbasu@nvidia.com>
Signed-off-by: Sandipan Patra <spatra@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reverts commit 701b7b1d2c. It will
be immediately replaced by a different implementation that is more
complete and runs are more targetted times.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use GNU make pattern rules to indicate that a single run of binman
produces all three Tegra output files. The avoids make running binman
three times (perhaps in parallel) and those instances inteferring with
each other.
See http://patchwork.ozlabs.org/patch/944611/ for the bug report.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Scott is no longer maintaining the NAND subsystem, mark as orphaned for
now.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Now CPSW driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):
- network drivers
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
<-- phydev is connected to dev which is UCLASS_ETH device
if (priv->phy_of_handle > 0)
dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
<-- phydev->dev->node is overwritten by phy-handle DT node
- PHY driver in .config() callback
int node = dev_of_offset(dev);
<-- PHY driver uses overwritten dev->node
const void *fdt = gd->fdt_blob;
if (fdtdec_get_bool(fdt, node, "property"))
...
As result, UCLASS_ETH device can't be used any more for DT accessing.
This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.
Also, common.h includes config.h as the first thing it does, so don't
include it directly.
Series-to: u-boot
Series-cc: Grygorii Strashko <grygorii.strashko@ti.com>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.
[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Because some phy wants to export some functions [1], export.h was
including the whole phy subsystem which pulls in lots of stuff that
causes some ordering and redefinition issues. Split out the only part
that is actually needed in export.h and include it there and in phy.h.
[1] commit 9527931507 ("board/ls2085rdb: Export functions for
standalone AQ FW load apps")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The include/phy.h will start including dm.h, which pulls in
linux/compat.h after the attempted redefinition in
arch/arm/include/asm/armv8/mmu.h, so move this include to allow
redefinition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).
It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.
Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Add driver model support to the mvgbe driver. As a temporary measure
both DM and non-DM uses are supported. Once all the users have been
converted the non-DM support can be dropped.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extract some function bodies to helper functions that can be reused in
the DM/non-DM implementations.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if_type is not correctly initialized
Failure to initialize if_type means that grub2/efinet sends
a bogus arp request. It therefore gets no response. On Raspberry Pi 3B+
this leads to a pause at:
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The same basic parsing was implemented in tftp and nfs, so add a helper
function to do the work once.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Instead of depending on a env callback for bootfile, read it explicitly.
We do this because the bootfile can be specified on the command line and
if it is, we will overwrite the internal variable. If a netboot_common()
is called again with no bootfile parameter, we want to use the one in
the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
With net autoload, we check the prerequisites for the initial command,
but the greater prerequisites when autoloading are not checked.
If we would attempt to autoload, check those prerequisites too.
If we are not expecting a serverip from the server, then don't worry
about it not being set, but don't attempt to load if it isn't.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
For net_boot_common, we allow the serverip to be specified as part of
the boot file name. For net commands that require serverip, include that
source as a valid specification of serverip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
nfs was only printing basic info about the transfer in the case of a
DEBUG build. Print the same level of detail as tftp always.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
The check for sending to the gateway was not using the correct variable
for comparison, so it was reporting that packets are sent to the gateway
when they were not.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Ask the OS for each of its interfaces and for each one, bind a U-Boot
device and then probe it. This will allocate the priv data structure
that is then populated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't necessarily know how many MAC addresses we'll need, so implement
a ROM read so we always have something valid.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With systemd stable interface names, eth0 will almost never exist.
Instead of using that name in the sandbox.dts, use an index.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of doing a simple string compare against "lo", look for the flag
that indicates a localhost interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we let descriptors equal 0, we can end up closing STDIN. Make sure
they start out as -1.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With driver model, we were not checking if the state of the device was
marked as active before calling the halt function. Check that the device
is probed and also marked as active. This avoids the case where we were
calling halt on the first device in net_init() and the driver would
operate on bogus data structures causing problems. In this case, the
priv was all 0, so halt() would close STDIN.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
test.dts specified the fake MAC address as a u32 array. Instead it
should be a u8 array.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In open, the socket is correctly checked to be -1 in the error case.
In send and recv, we checked for 0, but that is a valid socket number.
Correct this by checking for -1 as a bad socket everywhere.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.
In [1], Simon disabled this. His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.
[1] commit 8969ea3e9f ("sandbox: Disable Ctrl-C")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't necessarily want to re-enable ctrl-c if it was already disabled
when calling tstc().
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
Some legacy boards use RAW image for SPL boot. Add Kconfig option
SPL_PAYLOAD to set alternative image.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit a52ff334c5 ("armv8: ls1046ardb: SPL size reduction") reduced
image size for SPL. IFC was disabled. If PPA is loaded in SPL, MMU is
enabled as a result. Removing IFC skips IFC region in the MMU table,
causing later failure in RAM version U-boot when accessing CPLD
through IFC. Only disable IFC if PPA is not enabled for SPL.
Signed-off-by: York Sun <york.sun@nxp.com>
Make the code structure more general so that more socs can be
added easily and also remove speed limitation restriction.
Add the ls1012a sata support as well.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
(with and without CONFIG_OF_LIVE on zynqmp zcu102)
Reviewed-by: York Sun <york.sun@nxp.com>
One ls1012a, there is one SATA 3.0 advanced host controller interface
which is a high-performance SATA solution that delivers comprehensive
and fully-compliant generation 3 (1.5 Gb/s - 6.0 Gb/s) serial ATA
capabilities, in accordance with the serial ATA revision 3.0 of Serial
ATA International Organization.
Add sata node to support this feature.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable I-cache for SPL boot to boost performance. Earlier MMU was
enabled only for LS2080A and has since been dropped by commit
f539c8a4a7 ("armv8: ls2080a: Drop early MMU for SPL build").
Signed-off-by: York Sun <york.sun@nxp.com>
Move CONFIG_SPI_FLASH_SPANSION, CONFIG_SPI_FLASH, to defconfig.
Also disable disable 4K erase size option.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
4K erase size is used only in case of hydrid mode which is not
supported on any NXP platform with flash "s25fs512s".
Supported mode is uniform sector, with erase size 256kiB.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch updates the copyright claim for the issues reported by
legal review.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
CONFIG_SPL_FSL_LS_PPA is needed only in case of falcon boot
Support for this is not present in PPA currently, so
removing the default option from defconfig
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
use "fsl_mc lazyapply dpl addr" instead of "fsl_mc apply dpl addr"
change dpl load addr to 0x80001000 from 0x80200000 because dpl gets
corrupted at 0x80200000 during bootm command excecution.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On 64bit platforms we would otherwise see:
../cmd/ubi.c: In function 'ubi_volume_read':
../cmd/ubi.c:359:16: warning: format '%u' expects argument of type 'unsigned int', but argument 2 has type 'size_t {aka long unsigned int}' [-Wformat=]
Fixes: 68c7025d99 ("cmd: ubi: print load size after establishing volume size")
Signed-off-by: Tom Rini <trini@konsulko.com>
Provide a unit test for the GetTime() runtime service.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allow specifying the precision when printing integers, e.g.
efi_st_printf("%.4u-%.2u-%.2u\n", year, month, day);
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the missing parts of the GetTime() runtime service.
Fill seconds.
Fill daylight saving time flag correctly.
Provide dummy values for capabilities.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove unused function efi_get_time_init().
Initialization of the RTC has to be done in board bring up not in the EFI
subsystem.
There is no RTC device in the UEFI spec. The RTC is only accessed through
the runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI subsystem accesses the real time clock and is enabled by default.
So we should drop any CONFIG_CMD_DATE dependency from the real time clock
drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This unit test checks the CalculateCrc32 bootservice and checks the
headers of the system table, the boot services tablle, and the runtime
services table before and after ExitBootServices().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
InstallConfigurationTable() may change the number of installed
configuration tables.
Check the crc32 of the system table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If the number of installed tables is changed in
InstallConfigurationTable() update the crc32 of the system table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use const for the buffer. We are not changing the buffer.
Use efi_uintn_t where prescribed by the UEFI spec.
Prefer u32 over uint32_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a unit test for InstallConfigurationTable().
A table is installed, updated, removed. The table entry and the
triggering of events is checked.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The system table contains a link to the list of configurations tables.
These include the device tree, SMBIOS table, and the ACPI table.
This array is currently statically linked. With the patch it is allocated
as EFI_RUNTIME_SERVICES_DATA. Due to the structure of the system table we
cannot work with a linked list here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
For the boot and runtime services tables and for the system table the
crc32 has to be set in the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a firmware revision in the system table using the Makefile
variables VERSION and PATCHLEVEL, e.g. 0x20180700 for v2018.07.
Correct the type of the firmware vendor. It is a u16* pointer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The headersize field has to be set to the size of the whole table
including the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Both in the boot and the runtime services tables we have to specify the
UEFI spec revision. The same value is already used for the system
table. So let's use a common constant.
In the boot services table we have to provide the header signature.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
After clearing the screen the cursor position is row 0, column 0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the reset service of the EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
This should resolve the error reported by the SCT in
Protocol/SimpleTextIn/BlackBoxTest/SimpleTextInBBTestFunction.c:193
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The revision number has to be set in the loaded image protocol.
The problem was detected by running the SCT in
Protocol/LoadedImage/BlackBoxTest/LoadedImageBBTestMain.c:890
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Set the DM_FLAG_NAME_ALLOCED flag to avoid a memory leak when the block
device is removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a unit test for writing to a FAT file system.
Add some additional comments in block device unit test.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
fs_fat_write() is not able to write to subdirectories.
Currently if a filepath with a leading slash is passed, the slash is
treated as part of the filename to be created in the root directory.
Strip leading (back-)slashes.
Check that the remaining filename does not contain any illegal characters
(<>:"/\|?*). This way we will throw an error when trying to write to a
subdirectory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec requires that the memory map key is checked in
ExitBootServices().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Check the parameters of boottime service GetMemoryMap().
Return EFI_INVALID_PARAMETER where required by the UEFI spec.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rigorously check the TPL level and the event type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Some times gcc may generate data that is then used within code that may
be part of an efi runtime section. That data could be jump tables,
constants or strings.
In order to make sure we catch these, we need to ensure that gcc emits
them into a section that we can relocate together with all the other
efi runtime bits. This only works if the -ffunction-sections and
-fdata-sections flags are passed and the efi runtime functions are
in a section that starts with ".text".
Up to now we had all efi runtime bits in sections that did not
interfere with the normal section naming scheme, but this forces
us to do so. Hence we need to move the efi_loader text/data/rodata
sections before the global *(.text*) catch-all section.
With this patch in place, we should hopefully have an easier time
to extend the efi runtime functionality in the future.
Signed-off-by: Alexander Graf <agraf@suse.de>
[agraf: Fix x86_64 breakage]
This function currently returns an error code, but never uses it. There is
no function comment so it is not obvious why. Presuambly the error is not
important.
Update the function to explain its purpose and why it ignores the error.
Drop the useful error return value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This is a bit confusing at present since it adds 4KB to the pointer, then
rounds it up. It looks like a bug, but is not.
Move the 4KB addition into a separate statement and expand the comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Fix the 'amp' typo, expand on what 'steps' is and fix a few other minor
things.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present a NULL pointer passed to printf for a %pU argument will cause
U-Boot to access memory at 0. Fix this by adding a check, and print
"(null)" instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
[agraf: s/(null)/<NULL>/]
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently expose host addresses in the EFI memory map. That can be
bad if we ever want to use sandbox to boot strap a real kernel, because
then the kernel would fetch its memory table from our host virtual address
map. But to make that use case work, we would need to have full control
over the address space the EFI application sees.
So let's expose only U-Boot addresses to the guest until we get to the
point of allocation. EFI's allocation functions are fun - they can take
U-Boot addresses as input values for hints and return host addresses as
allocation results through the same uint64_t * parameter. So we need to
be extra careful on what to pass in when.
With this patch I am successfully able to run the efi selftest suite as
well as grub.efi on aarch64.
Signed-off-by: Alexander Graf <agraf@suse.de>
With sandbox the U-Boot code is not mapped into the sandbox memory range
so does not need to be excluded when allocating EFI memory. Update the EFI
memory init code to take account of that.
Signed-off-by: Simon Glass <sjg@chromium.org>
[agraf: Remove map_sysmem() call and header reference]
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that elf.h contains relocation defines for all architectures
we care about, let's just include it unconditionally and refer to
the defines.
Signed-off-by: Alexander Graf <agraf@suse.de>
We need to know about x86 relocation definitions even in cases where
we don't officially build against the x86 target, such as with sandbox.
So let's move the x86 definitions into the common elf header, where all
other architectures already have them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Thanks to CONFIG_SANDBOX, we can not rely on config options to tell us
what CPU architecture we're running on.
The compiler however does know that, so let's just move the ifdefs over
to compiler based defines rather than kconfig based options.
Signed-off-by: Alexander Graf <agraf@suse.de>
Varargs differ between sysv and ms abi. On x86_64 we have to follow the ms
abi though, so we also need to make sure we use x86_64 varargs helpers.
This patch introduces generic efi vararg helpers that adhere to the
respective EFI ABI. That way we can deal with them properly from efi
loader code and properly interpret variable arguments.
This fixes the InstallMultipleProtocolInterfaces tests in the efi selftests
on x86_64 for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
In the sandbox environment we can not easily build efi stub binaries
right now, so let's disable the respective test cases for the efi
selftest suite.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
When running on the sandbox the stack is not necessarily at a higher memory
address than the highest free memory.
There is no reason why the checking of the highest memory address should be
more restrictive for EFI_ALLOCATE_ANY_PAGES than for
EFI_ALLOCATE_MAX_ADDRESS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: use -1ULL instead]
Signed-off-by: Alexander Graf <agraf@suse.de>
We try hard to make sure that SMBIOS tables live in the lower 32bit.
However, when we can not find any space at all there, we should not
error out but instead just fall back to map them in the full address
space instead.
This can for example happen on systems that do not have any RAM mapped
in the lower 32bits of address space. In that case having any SMBIOS
tables at all is better than having none.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bootefi command gets a few addresses as values passed in. In sandbox,
these values are in U-Boot address space, so we need to make sure we
explicitly call map_sysmem() on them to be able to access them.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI image loader tries to determine which target architecture we're
working with to only load PE binaries that match.
So far this has worked based on CONFIG defines, because the target CPU
was always indicated by a config define. With sandbox however, this is
not longer true as all sandbox targets only encompass a single CONFIG
option and so we need to use compiler defines to determine the CPU
architecture.
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit c524997acb.
Booting ARMv7 in non-secure mode using bootefi works now.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
ARMV7_LPAE is required in order to enable the MMU in HYP mode.
And we really want to enable the MMU in HYP mode such that we can
enable the the caches. Otherwise U-Boot code (such as the EFI
implementation) that runs in HYP mode will run at a snils pace.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Multiple EFI binaries may be executed in sequence. So if we already
are in non-secure mode after running the first one we should skip
the switching code since it no longer works once we're non-secure.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If desired (and possible) switch into HYP mode or non-secure SVC mode
before calling the entry point of an EFI application. This allows
U-Boot to provide a usable PSCI implementation and makes it possible
to boot kernels into hypervisor mode using an EFI bootloader.
Based on diffs from Heinrich Schuchardt and Alexander Graf.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
[agraf: Fix indentation]
Signed-off-by: Alexander Graf <agraf@suse.de>
The current code that switches into HYP mode doesn't bother to set
up a stack for HYP mode. This doesn't work for EFI applications
as they expect a usable stack. Fix this by migrating the stack
pointer from SP_svc to SP_hyp while in Monitor mode.
This restores the stack pointer when we drop into HYP mode.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The following generated files should be ignored by git:
efi_miniapp_file_image_exit.h
efi_miniapp_file_image_return.h
*.so files are normally deleted during the build but should be
ignored too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable "mtdparts" and "ubi" commands for uniphier_v8_defconfig to
use UBI on NAND devices.
Enable only "mtdparts" for uniphier_{v7,ld4_sld8}_defconfig because
enabling UBI would increase 170KB, which would be memory footprint
problem.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The 'bd' is passed in ft_board_setup() as the second argument.
Replace 'gd->bd' with 'bd'.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add 'const' (also 'static' in some places) to struct node_info
arrays to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The second argument of fdt_fixup_mtdparts() is an opaque pointer,
'void *node_info', hence callers can pass any pointer.
Obviously, fdt_fixup_mtdparts() expects 'struct node_info *'
otherwise, it crashes run-time.
Change the prototype so that it is compile-time checked.
Also, add 'const' qualifier to it so that callers can constify
the struct node_info arrays.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The NAND framework makes sure to pass in the buffer with at least
chip->buf_align alignment. Currently, the Denali NAND driver only
requests 16 byte alignment. This causes unaligned cache operations
for the DMA transfer.
[Error Example]
=> nand read 81000010 0 1000
NAND read: device 0 offset 0x0, size 0x1000
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
4096 bytes read: OK
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
cherry-pick kernel commit 2ae89c7 (2018-06-05)
to avoid warnings when compiling with GCC 8.1
In file included from scripts/kconfig/zconf.tab.c:2486:
scripts/kconfig/confdata.c: In function ‘conf_write’:
scripts/kconfig/confdata.c:771:22: warning: ‘%s’ directive writing likely 7 or more bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(newname, "%s%s", dirname, basename);
^~
scripts/kconfig/confdata.c:771:19: note: assuming directive output of 7 bytes
sprintf(newname, "%s%s", dirname, basename);
^~~~~~
scripts/kconfig/confdata.c:771:2: note: ‘sprintf’ output 1 or more bytes (assuming 4104) into a destination of size 4097
sprintf(newname, "%s%s", dirname, basename);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
scripts/kconfig/confdata.c:774:23: warning: ‘.tmpconfig.’ directive writing 11 bytes into a region of size between 1 and 4097 [-Wformat-overflow=]
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~
scripts/kconfig/confdata.c:774:3: note: ‘sprintf’ output between 13 and 4119 bytes into a destination of size 4097
sprintf(tmpname, "%s.tmpconfig.%d", dirname, (int)getpid());
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable CVE_2017_5715 mitigation on CPU0 on R-Car H2, M2W, M2N, V2H,
which all contain Cortex-A15 cores. R-Car E2 contains only Cortex-A7
cores and is not affected. Without this enabled, Linux kernel reports:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
With this enabled, Linux kernel reports:
CPU0: Spectre v2: using ICIALLU workaround
NOTE: This by itself does not enable the workaround for other CPUs
than CPU0 and may require additional kernel patches for the
other CPUs in SMP configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Arria10 requires proper configuration of the NOC firewall, otherwise
the access to certain areas of the LWHPS bridge fails in Linux. Add the
missing setup.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Commit bfc6bae8fa
This commit rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET. Update
with new CONFIG name and enable CONFIG_SPL_DM_RESET when CONFIG_DM_RESET is enabled.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
The patch
"tools/mkimage: Fix DTC run command to handle file names with space"
(sha1: a6e9810495) contains comma in name
which is confusing patman. Fix it by defining Mirza's email in mailmap.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The NAND offsets for the kernel and U-Boot were missing.
This patch sets up the offsets so the AM3517-EVM can boot from NAND
when DIP switches S7:1 and S7:4 are to the OFF position
Signed-off-by: Adam Ford <aford173@gmail.com>
The previous e-mail pointing to Vaibhav Hiremath <hvaibhav@ti.com>
is bouncing and has for some time. This updates it to myself and I
work for Logic PD the manufacturer of the AM3517-SOM and EVM
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently the U-Boot project contains 2 documentation directories:
- doc/
- Documentation/
The Documentation directory only contains device tree bindings related
content, so move the 3 files to doc/device-tree-bindings/.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
There is no reason not to use macros which are already defined.
It is also much easier for grepping.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Header file "asm/utils.h" is not required to compile "spl_ymodem.c".
So, removing this dependency allows other architectures to use this
booting device as "asm/utils.h" is only present in "arm" architecture.
Signed-off-by: Paulo Zaneti <paulo.zaneti@datacom.ind.br>
The length returned by hexport_r has a few redundant characters.
This appears as NULL characters at the end so seems harmless.
Remove the surplus counts in two places
totlen += strlen(ep->key) + 2;
I'm guessing the +2 here is for = and sep char. But there is another
totlen += 2; line that does that.
size = totletn + 1;
Doesn't make sense and isn't justified with any comment.
Signed-off-by: Zubair Lutfullah Kakakhel <zubair@resin.io>
Use blk_dread()/blk_dwrite() in mmc_read()/mmc_write() AVB operation
implementations. This fixes compilation issues when CONFIG_BLK is
enabled.
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
In the case that there was no name defined for a partition the
code assumes that name_len is 22 and therefore allocates exactly
that space for a dummy name. But the function sprintf() first
resolves "0x%08llx@0x%08llx" to a string that is longer than 22
bytes. This leads to a buffer overflow. The replacement function
snprintf() limits the copied bytes to name_len and therefore
avoids the buffer overflow.
Signed-off-by: Kay Potthoff <Kay.Potthoff@microsys.de>
With recent kernel v4.18-rcx, uImage becomes bigger than 8MB.
Set SYS_BOOTM_LEN to 16MB, this fix the following error message:
"Fix Loading Kernel Image ... Image too large: increase
CONFIG_SYS_BOOTM_LEN"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
A comment in the kernel doc of the mtd_oob_ops structure tells that it
is not possible to write more than one page with OOB. This was
probably true at some time in the past but today it is entirely wrong.
As one can see for instance in the nand_do_write_ops() helper available
in the NAND core, this implementation called by mtd->_write_oob()
simply loops over the pages until everything has been written.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
rtc_to_tm() and rtc_mktime() are required for some RTC drivers, at least
PL031. Without this patch, we also need to enable CONFIG_CMD_DATE even if
we don't want or need this command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Our nand_ecc_modes_t is already a bit abused by value NAND_ECC_SOFT_BCH.
This enum should store ECC mode only and putting algorithm details there
is a bad idea. It would result in too many values impossible to support
in a sane way.
To solve this problem let's add a new enum. We'll have to modify all
drivers to set it properly but once it's done it'll be possible to drop
NAND_ECC_SOFT_BCH. That will result in a cleaner design and more
possibilities like setting ECC algorithm for hardware ECC mode.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b0fcd8ab7b3c89b5da7fff5224d06ed73e7a33cc]
[Philippe Reynes: adapt code to u-boot]
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Only the MUSB driver is currently supported on the omap3_logic
boards. The driver is using the new-musb and not the legacy
version, so this patch removes the dead code references.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to use the device tree for MMC, the card-detect pin
needs to be inverted. This patch places this into the
am3517-evm-u-boot.dtsi file to keep the main DTS and DTSI files
clean and in-sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
With the resync of the omap3.dtsi file, the reg-shift was removed
so it breaks the UART. Adding the reg-shift into the
am3517-evm-u-boot.dtsi keeps the reg-shift for U-Boot, but keeps
the dts/dtsi files clean from Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There have been some significant changes to the DM37 SOM-LV device
tree. This patch re-syncs it with Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been some refactoring of the DTS files for the Logic PD
DM37 Torpedo. This patch re-sync's the DTS files with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
There have been several minor changes to the OMAP3.dtsi, so this
patch re-syncs it with Linux. An addition include/dt-binding was
also brought with it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Several changes have been made to the AM3517-evm and the underlying
am3517.dtsi file. This patch re-sync's the DTS and DTSI files with
Linux.
Signed-off-by: Adam Ford <aford173@gmail.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Assigning a parameter which is not used afterwards has not effect.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are already definitions for ramdisk_addr_r and fdt_addr_r, so
having a duplicate copy called ramdiskaddr and fdtaddr is confusing.
This patch converts any references to ramdisk_addr_r and fdt_addr_r
and removes the duplicates.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USBOH module on imx25 chips contains two USB controllers which are
called USB OTG Controller and USB Host Controller. Each one has its EHCI
root hub. The OTG Controller's EHCI registers start at offset 0, the Host
Controller's registers start at offset 0x400.
We set CONFIG_MXC_USB_PORT=0 to select the OTG Controller and 1 for the
Host Controller. Therefore, IMX_USB_PORT_OFFSET must be 0x400. Using
this setting, the Host Controller starts working on my imx25 board.
Please note that the imx25 reference manual claims that the Host
Controller's registers start at 0x200. This is not correct. The Linux
Kernel uses the correct offset 0x400 in imx25.dtsi.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signing parts of a u-boot imximage for image verification in High
Assurance Boot (HAB) in a post-build process, requires some
information from the imximage header. Currently, this information is
only provided during the image build, which makes the transfer of this
information to the post-build process harder than necessary.
The i.MX HAB information (start and length) can be calculated either
by using information from the image-configuration file, or from the
information in the flash header of the imximage.
The advantage of using information from flash header is, that they are
not only available during image creation, but also available if
existing images are processed.
Example:
$ tools/mkimage -l u-boot.imx
Image Type: Freescale IMX Boot Image
Image Ver: 2 (i.MX53/6/7 compatible)
Mode: DCD
Data Size: 483328 Bytes = 472.00 KiB = 0.46 MiB
Load Address: 877ff420
Entry Point: 87800000
HAB Blocks: 0x877ff400 0x00000000 0x00071c00
DCD Blocks: 0x00910000 0x0000002c 0x00000208
Signed-off-by: Holger Dengler <dengler@linutronix.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
In preparation for delivery bottlenecks, enable support for GigaDevice, Macronix, and Winbond nor flash chips.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Since the vast majority of i.MX6 boards are migrating to SPL,
this patch converts im6q_logic to SPL and enables the SDP for
loading SPL and u-boot.img over USB. The Falcon mode only
supports NAND flash as of now due to limited space/RAM, but
all i.MX6D/Q SOM's from Logic PD have internal NAND from which
to boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
This reverts commit a637fe6f27.
The DDR DRAM calibration was enhanced by write leveling correction code.
It can be used with T-topology now.
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
The new config skips the boot menu which asks which board is in
use. This is useful to allow direct booting of image without user
iteration.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Our default config already has the secure mode supported, so the
manual step is not required anymore.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The DFU allows a more user friendly use as the details where the
bootloader is installed are abstracted.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the addition of extra default configurations for each
baseboard, removing the boot menu when user boots for the first time.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
The addrmap5 value is the same for the 512MB and 1GB variants,
so there is no need to override it.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the CAAM driver fails to be probed:
caam 30900000.caam: Entropy delay = 3200
caam 30900000.caam: failed to acquire DECO 0
caam 30900000.caam: failed to instantiate RNG
CAAM needs to be initialized in secure world, so enable
CONFIG_ARMV7_BOOT_SEC_DEFAULT to allow the driver to
probe successfully.
Tested with kernel mainline version 4.17.2.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Falcon mode boots the kernel directly from SPL, without loading
the full U-Boot.
As pico-imx7d does not have a GPIO for selecting Falcon versus
normal mode, enter in Falcon mode when the customer selects
the CONFIG_SPL_OS_BOOT option in menuconfig.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the baseboards do not offer a way to autodetect which one is
in use, so we ask the user if no value has been set.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx7d U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx7d to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the use of:
> run setup_emmc
inside of the U-Boot prompt to do the partitioning of the disk.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid`
environment helper to allow it to properly work with Yocto Project and
other distributions using extlinux autogenerated configuration files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of keeping a custom environment, use a more generic approach
by switching to disto config.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Not all i.MX6 pads use the same drive strength table. So far only the
240 Ohm to 34 Ohm table was available. Because the constants used have
speaking names it can be confusing to use e.g. PAD_CTL_DSE_48ohm when
according to the reference manual 52 Ohm is the correct value. This
patch adds the 260 Ohm to 37 Ohm table.
For example, the IOMUXC_SW_PAD_CTL_PAD_SD2_CLK register (SD-card clock)
uses the added table.
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This makes sure that all Colibri iMX7 modules work with the
same timing. The changes are:
- Disable ODT on read (JEDEC standard JESD79-3F says in chapter
5.2.3 ODT during Reads: "As the DDR3 SDRAM can not terminate
and drive at the same time, RTT must be disabled at least half
a clock cycle..." and also MX7D SABRESD is disabling it)
This alone fixed memory issues for two Colibri iMX7 1GB modules
which showed issues before
- Make sure tRFC(min) is at least 260ns
- Make sure tRC is >50.625ns
- tRP needs to be >13.125ns, we can lower from 18.75ns to 15ns
- tFAW is not relevant, leave at reset
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Device trees from vanilla Linux do not specify a i.MX 7 specific
compatible string. Make sure to set partitions also when booting
upstream Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Previously we had stored the environment right after the
u-boot.img on the disk. I never liked this because with dtbs
being included and such the image could grow in size. Instead
we move the environment to be negatively offset from the 1MB
mark. Almost all our images start at 4MB's, and most standard
images start at 1MB, and all our storage devices are a minimum
1MB. Therefore we can store env there for all classes of devices
and have plenty of space in case u-boot.img needs to grow.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Implement MIGRATE_INFO_TYPE. This informs Linux that no migration
for the trusted operating system is necessary:
[ 0.000000] psci: Trusted OS migration not required
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
So far psci_cpu_(on|off) only worked for CPU1. Allow to control
CPU0 too. This allows to run the Linux PSCI checker successfully:
[ 2.213447] psci_checker: PSCI checker started using 2 CPUs
[ 2.219107] psci_checker: Starting hotplug tests
[ 2.223859] psci_checker: Trying to turn off and on again all CPUs
[ 2.267191] IRQ21 no longer affine to CPU0
[ 2.293266] Retrying again to check for CPU kill
[ 2.302269] CPU0 killed.
[ 2.311648] psci_checker: Trying to turn off and on again group 0 (CPUs 0-1)
[ 2.354354] IRQ21 no longer affine to CPU0
[ 2.383222] Retrying again to check for CPU kill
[ 2.392148] CPU0 killed.
[ 2.398063] psci_checker: Hotplug tests passed OK
[ 2.402910] psci_checker: Starting suspend tests (10 cycles per state)
[ 2.410019] psci_checker: cpuidle not available on CPU 0, ignoring
[ 2.416452] psci_checker: cpuidle not available on CPU 1, ignoring
[ 2.422757] psci_checker: Could not start suspend tests on any CPU
[ 2.429370] psci_checker: PSCI checker completed
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
PSCI 1.0 require PSCI_VERSION, PSCI_FEATURES, AFFINITY_INFO and
CPU_SUSPEND to be implemented. Commit 0ec3d98f76 ("mx7_common:
use psci 1.0 instead of 0.1") marked the i.MX 7 implementation to
be PSCI 1.0 compliant but failed to implement those functions.
Especially the missing PSCI version callback was noticeable when
booting Linux:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv65535.65535 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
This patch provides a minimal implementation thereof. With this
patch applied Linux detects PSCI 1.0:
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.0
Fixes: 0ec3d98f76 ("mx7_common: use psci 1.0 instead of 0.1")
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
There is no need for assembly in the platform specific part of
the PSCI implementation.
Note that this does not make it a complete PSCI 1.0 implementation
yet but aids to do so in upcoming patches.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This function can be used only for some of the nxp SoC. Make
it explicit in the comment. This adjust a bit commit
3aa4b703b4 ("imx: imx6: Move gpr_init() function to soc.c")
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
i.MX7 does not support BMODE due to the erratum e10574 ("Watchdog:
A watchdog timeout or software trigger will not reset the SOC"), so
remove its support.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Mainline and now the SolidRun 4.9 nxp based tree use the new
reorganization of device-tree files that separate out the emmc
into its own dtb. u-boot will now look for -emmc in the device
tree name if one is detected.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Previously we had just made broad assumptions with which of our
boards had an eMMC or not even though this is a manufacturing time
assembly option. This takes the guessing away and actually checks for
the existence of an eMMC and sets up the has_emmc environment variable.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The HB2 boards as well as rev 1.5 soms support eMMC
booting as well as SDHC. Add the infrastructure to support
booting these devices.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The IN_PROGRESS macro has been removed in commit bd47c13583 (mmc: Fix
splitting device initialization). Remove it from the mmc_start_init()
function description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The GPMI NAND IP seems to be the same as used in i.MX 6Quad. Use
the fsl,imx6q-gpmi-nand compatible string like Linux devices trees
are.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This macro allows to detect whether the boot ROM initialized USB
already (serial downloader). This is helpful to reliably detect
if the system has been recovered via USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the bootcounter address is in a cached memory,
a flush of dcache must occur after updateing the bootcounter.
Issue found on i.MX6 where bootcounter is put into the internal
(cached) IRAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The DA850-EVM and OMAPL138_LCDK both use checks for CONFIG_USE_NAND.
This patch changes these checks to CONFIG_NAND which is already defined
in Kconfig. Since the OMAPL138_LCDK already had CONFIG_NAND defined in its
defconfig, it can be deleted from configs/omapl138_lcdk.h.
Signed-off-by: Adam Ford <aford173@gmail.com>
Some boards indicate support from booting NAND or
ONENAND booting, but don't enable the CONFIG_NAND. This
makes those boards imply NAND which will make
enabling other flags that are dependent on CONFIG_NAND
possible and easier to migrate.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add Kconfig options SPL_ENV_* and TPL_ENV_* and simplify Makefile.
This allows SPL/TPL image has different environment setting from
full feature U-Boot.
Signed-off-by: York Sun <york.sun@nxp.com>
Currently the fdtfile environment variable is set to
CONFIG_DEFAULT_DEVICE_TREE which is іnternally used as U-Boot devicetree
source. The OS can use a different filename and Kconfig gives us the
ability to select a default devicetree via CONFIG_DEFAULT_FDT_FILE.
This also gives user configuring U-Boot via menuconfig the behaviour
someone would expect.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On the veyron board the vcc33_sd regulator is used as vmmc-supply for
the SD card. This regulator is powered in the MMC core during power on
but its value is never actually set.
In the veyron platform the reset value for the LDO output is 1.8V while
the standard (min and max) value for this regulator defined in the DTS
is 3.3V. When the MMC core enable the regulator without setting its
value, the output is automatically set to 1.8V instead of 3.3V.
With this patch we preemptively set the value to 3.3V.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GRF_SOC_CON0.grf_force_jtag bit is automatically set at boot and it
is preventing the SDMMC to work correctly. Disable the JTAG function on
the assumption that a working SD has higher priority over JTAG.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The first dhcp command consistently fails with a timeout when
the lion-rk3368 board is connected to a Zyxel GS1100-24E
Gigabit Ethernet switch:
ethernet@ff290000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increasing PHY_ANEG_TIMEOUT from the default 4000 to 8000 makes the
first dhcp command work reliably.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Without the patch SPL (in case of an error) creates an output like:
U-Boot SPL board initMissing DTB
The patch adds the missing line feed. So now we get:
U-Boot SPL board init
Missing DTB
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The order distroboot searches for a boot.scr is fixed at compile time.
To make BIOS_DISABLE work as expected and boot from mmc1 instead of
mmc0 if enabled, we need to change the environment at runtime.
Especially as commit: 482cf22333 ("rockchip: rk3399-puma: add boot-on
regulator to override BIOS_DISABLE") enables the eMMC in U-Boot even
if BIOS_DISABLE is active.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This implements the new 'spl_perform_fixups' hook for RK3399-based
boards and injects the /chosen/u-boot,spl-boot-device with an ofpath
corresponding to the boot device used.
The intended usage is for the full U-Boot stage to evaluate this in
scripts and then adapt its boot-order when using distro-boot.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To let the full U-Boot know where it was booted from (i.e. which of
the entries in /chosen/u-boot,spl-boot-order' contained a valid
image), we define (and document) /chosen/u-boot,spl-boot-device as the
property that could/should automatically be injected by SPL.
This commit only contains a documentation change, which documents the
new property and the intended usage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
On some boards, we want to give the board/architecture-specific code a
chance to look at where the next image has been loaded from and
perform fixups before starting the next image. This is of particular
importance, when we probe multiple devices for bootable payloads and
boot the first one found.
This change adds the following:
- we record the boot_device used into the spl_image structure
- we provide an extension-point for boards/architectures that can
perform late fixups depending on a fully populated spl_image
structure (i.e. we'll know the final boot_device and have info
on the image type and operating system to be booted).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The SPL code for smartweb is close to its limit and adding a few extra
instructions to SPL will cause it to overrun its sram allotement (thus
causing build failures). To allow adding the 'spl_perform_fixups'
extension point to SPL, we'll enable SPL_TINY_MEMSET for smartweb.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Series-cc: trini
rk3066 and rk3188 has two I2C controller implementations.
Current I2C driver wan't work with legacy implementation.
Switching between controllers is performed using a bit inside
GFR_SOC_CON1 register. The bit setting is performed by pinctrl
driver. The patch ask pinctrl to do settings.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fix warnings by including the rk3228 variant in the compatible-list]:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Explicitly add 'python' call for 'acs_tool.pyc', to avoid failed
execution on some OSes.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.5
(Linux commit 54fb3c180d05e9dfda892a93413514e99f0cbb19).
This will enable HDMI_5V for USB Amlogic Meson GXL P212 based boards.
Signed-off-by: Loic Devulder <ldevulder@suse.de>
This tests that the importing of an environment with a specified
whitelist works as intended.
If there are variables passed as parameter to the env import command,
those only should be imported in the current environment.
For each variable passed as parameter, if
- foo is bar in current env and bar2 in exported env, after importing
exported env, foo shall be bar2,
- foo does not exist in current env and foo is bar2 in exported env,
after importing exported env, foo shall be bar2,
- foo is bar in current env and does not exist in exported env (but is
passed as parameter), after importing exported env, foo shall be empty
ONLY if the -d option is passed to env import, otherwise foo shall be
bar,
Any variable not passed as parameter should be left untouched.
Two other tests are made to test that size cannot be '-' if the checksum
protection is enabled.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
While the `env export` can take as parameters variables to be exported,
`env import` does not have such a mechanism of variable selection.
Let's add the ability to add parameters at the end of the command for
variables to be imported.
Every env variable from the env to be imported passed by parameter to
this command will override the value of the variable in the current env.
If a variable exists in the current env but not in the imported env, if
this variable is passed as a parameter to env import, the variable will
be unset ONLY if the -d option is passed to env import, otherwise the
current value of the variable is kept.
If a variable exists in the imported env, the variable in the current
env will be set to the value of the one from the imported env.
All the remaining variables are left untouched.
As the size parameter of env import is positional but optional, let's
add the possibility to use the sentinel '-' for when we don't want to
give the size parameter (when the env is '\0' terminated) but we pass a
list of variables at the end of the command.
env import addr
env import addr -
env import addr size
env import addr - foo1 foo2
env import addr size foo1 foo2
are all valid.
env import -c addr
env import -c addr -
env import -c addr - foo1 foo2
are all invalid because they don't pass the size parameter required for
checking, while the following are valid.
env import addr size
env import addr size foo1 foo2
Nothing's changed for the other parameters or the overall behaviour.
One of its use case could be to load a secure environment from the
signed U-Boot binary and load only a handful of variables from an
other, unsecure, environment without completely losing control of
U-Boot.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
When vars are passed to the himport_r function with H_NOCLEAR flag,
those vars will be overridden in the current environment and if one of
those vars is not in the imported environment, it'll be deleted in the
current environment whatever the flag passed to himport_r.
The H_NOCLEAR flag is used to clear the whole environment whether vars
are passed to the function or not.
This leads to incoherent behaviour. If one passes vars to himport_r
with the H_NOCLEAR flag, if a var in vars is not in the imported env,
that var will be removed from the current env.
If one passes vars to himport_r without the H_NOCLEAR flag, the whole
environment will be removed and vars will be imported from the
environment in RAM.
It makes more sense to keep the variable that is in the current
environment but not in the imported environment if the H_NOCLEAR flag is
set and remove only that variable if the H_NOCLEAR flag is not set.
Let's clear the whole environment only if H_NOCLEAR and vars are not
passed to himport_r.
Let's remove variables that are in the current environment but not in
the imported env only if the H_NOCLEAR flag is not passed.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Some functions have different behaviour when the given address is 0
(assumed to be NULL by the function).
find_ram_base() does not return 0 anymore so it's safe to remove those
offsets.
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Some functions test that the given address is not NULL (0) and fail or
have a different behaviour if that's the case (e.g. hexport_r).
Let's make the RAM base address to be not zero by setting it to 2MiB if
that's the case.
2MiB is chosen because it represents the size of an ARM LPAE/v8 section.
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The error message should start with `## Error: ` so that it's easily
detectable by tests without needing to have a complex regexp for
matching all possible error message patterns.
Let's add the `## Error: ` prefix to the error messages since it's the
one already in use.
Suggested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch add clk_enable/clk_disable/clk_get_rate support for
- DSI_PX
- LTDC_PX
- DSI_K (only get rate)
These clocks are needed for LTDC and DSI drivers with latest device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
the function compute the VCO PLL freq, used in
- stm32mp1_read_pll_freq()
- pll_set_rate()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/clk/clk_stm32mp1.c
This patch define RCC_PLLNCFGR2_SHIFT to reuse it in
the pll function for set rate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add support of stm32mp157c-ev1, the evaluation board with pmic stpmu1
(ev1 = mother board + daughter ed1) with device tree.
EV1 is the selected board by default in basic defconfig.
PS: CONFIG_PINCTRL_FULL activation avoid to increase
SYS_MALLOC_F_LEN (Early malloc usage: 2034)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use new API syscon_node_to_regmap in sysreset_syscon driver
for compatible "syscon-reboot"; that's avoid the need of explicit
syscon binding for "regmap" handle.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For qemu-x86 the date command produces wrong days of the week:
Date: 2018-07-06 (Saturday) Time: 18:02:03
Date: 2018-07-07 (unknown day) Time: 21:02:06
According to a comment in the Linux driver the mc146818 only updates the
day of the week if the register value is non-zero.
Sunday is 1, saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf).
So let's use our library function to determine the day of the week.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The test for (CONFIG_BOOTDELAY >= 0) has been in U-Boot since the
beginning, but the meaning of it has changed over time. Allow the
default to be set for any value, including -ve ones. This allows
(for example) CONFIG_ENV_IS_NOWHERE to have values for bootdelay in
its compiled in environment.
The only thing this changes is where the default for bootdelay can be
fetched from; before this change you get a compiled in default, after
you'll pull it from the default value in the environment, but both values
will be the same. Also if there's a value set in the environment then
that will take precedence (as before).
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The comparison
logical > item->logical + item->length
in btrfs_map_logical_to_physical is wrong and should be instead
logical >= item->logical + item->length
For example, if
item->logical = 4096
item->length = 4096
and we are looking for logical = 8192, it is not part of item (item is
[4096, 8191]). But the comparison is false and we think we have found
the correct item, although we should be searing in the right subtree.
This fixes some bugs I encountered.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
The wrapper #ifndef is currently missing in acpi_table.h. Add it to
prevent it from being included multiple times.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
write_acpi_tables() currently touches ACPI hardware to switch to
ACPI mode at the end. Move such operation out of this function,
so that it only does what the function name tells us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
acpi_find_fadt(), acpi_find_wakeup_vector() and enter_acpi_mode()
are something unrelated to ACPI tables generation. Move these to
a separate library.
This also fixes several style issues reported by checkpatch in the
original codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In preparation for the reset driver conversion, eliminate the
reset_cpu() call in the FSP init path as it's too early for the
reset driver to work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds full reset bit in the reset register value in the ACPI FADT
table, so that kernel can do a thorough reboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This is needed for having access to the devices below this bus, most
important is uart and boot-device (spi, mmc, ...) in SPL stage.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On other OS, not one provided by B&R, it is not guaranteed that there
are factory-settings within a devicetree. So we must not treat the
absence of them as error.
Further we've the fact that on different version of the device-tree
files there are different namings of the factory-settings, we consider
this with searching for an alternative name.
changing things as following:
- don't treat as error if the bootloader version cannot written into
devicetree.
- since the naming of the factory-settings are different in different
versions of the provided device-tree we search for the alternate name
"/fset"
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
If a board-code calls the pmicsetup(u32 mpupll) with a mpupll value
!= 0 it wants to force some frequency with the value provided by mpupll.
Setting up 1 GHz is wrong here.
Nobody did take notice about that yet, since every board calls this
function with zero.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This interface names may vary over different products, to consider this
fact we replace the interface label "IF1" and "IF2" on the summary
screen with some more generic wording "MAC1" and "MAC2".
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Since we're going to drop LCD-support on brppt1 boards, we have to make
this stuff here optional and remove the #error path.
We also move out the ft_board_setup(...) from this #ifdef because
there's no relationship with the LCD-code and on the other hand this is
still needed in future even with LCD-support off.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The linux systems running on the brppt1 targets are using modern DRM
drivers since long time ago. Further we are going to drop the LCD
support completely on this board, so the simple-framebuffer setup
becomes obsolete.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Current implementation of find_next_zero_bit() is incompatible with arm64.
Hence fix it by using BITS_PER_LONG define instead of constants and
use generic ffz() implementation.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of phy are provided from a PHY provider nodes as following:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <1>;
};
};
and PHY are called as following:
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc_clk USBH>;
resets = <&rcc_rst USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
companion = <&usbh_ohci>;
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The function set_default_vars() in common.c adds H_INTERACTIVE to the
h_import() flag, but the function has no way of telling if the command
actually was user directed like this flag suggest. The flag should be
set by the calling function do_env_default() in nvedit.c instead, where
the command is certainty user directed.
Move the H_INTERACTIVE flag from set_default_vars() to do_env_default().
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The env_flag in do_env_default() doesn't get propagated and therefore
gets ignored by himport_r(). This breaks to ability to "forcibly" reset
variables to their default values using the environment command.
Scenario example of the problem:
# setenv kernel uImage
# setenv .flags kernel:so
# env default -f kernel
## Error: Can't overwrite "kernel"
himport_r: can't insert "kernel=zImage" into hash table
Change the call path so it will pass the flag correctly.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The naming convention for flags in nvedit.c is:
* The hashtable flag (defined in search.h) is named "env_flag"
* The command flag argument (defined in command.h) is named "flag"
This convention is kept in functions like do_env_print(), do_env_set()
and do_env_delete(), but not in do_env_default().
Rename the hashtable flag in do_env_default() from "flag" to "env_flag".
Rename the command flag in do_env_default() from "__flag" to "flag".
No functional change.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
When sourcing a FIT format script, if we've not been told the unit name
to use, look for a default property at the root of /images to work out
which unit we should use.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add ut_assertnull macro to include/test/ut.h
For testing of functions that returns NULL on errors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xilinx changes for v2018.09
clk:
- Fix zynqmp clock driver
common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return macros in cmd_process_error
- Fix duplication of CONFIG_SYS_PROMPT_HUSH_PS2
- Support watchdog in usb_kbd.c
- Fix name usage in usb_kbd.c
- Support systems with non zero memory start initialized from DT only
gpio:
- Add support for manual relocation in uclass
- zynq - use live tree
- zynq - fix match data reading
- zynq - setup bank name
- xilinx - convert driver to DM
microblaze:
- Use generic iounmap/ioremap implementations
- Redesign reset logic with sysreset features
- Use watchdog and gpio over DM
- Remove unused macros and fix some checkpatch issues
- Fix timer initialization not to be called twice
serial:
- zynq - Use platdata intead of priv data
sysreset:
- Add support for manual relocation in uclass
- Add gpio-restart driver
- Add microblaze soft reset driver
watchdog:
- Add support for aliases in uclass
- Add support for manual relocation in uclass
- Convert xilinx driver to DM
- cadence - update info in the driver and not stop wdt in probe
xilinx:
- Enable LED gpio for some targets with gpio-leds DT node
- Setup variables via Kconfig
zynq:
- Add support for watchdog aliases
- Add support for mini nand/nor configurations
- Wire FPGA initalization in SPL
zynqmp:
- Enable mass storage for zcu100
- Handle external pmufw files
- Add support for secure images
- Some Kconfig movements and alignments
- Add support for watchdog aliases
- Use subcommands style for platform command
- Add mmio_read/write platform commands
- DT updates
- Add support for mini qspi configuration
commit 4aba5fb857 ("arm: zynq: Rework FPGA initialization")
moved FPGA initialization from board_init() to arch_early_init_r(),
which is not called as part of the SPL
Fix this by calling arch_early_init_r() in the spl_board_init()
function, so the FPGA is correctly initialized
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Disable the use of function zynq_loadfs when compiling
the driver for the SPL, as the following filesystem
functions are not found by the linker:
- fs_set_blk_dev
- fs_read
- fs_set_blk_dev
- fs_read
- fs_read
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A message should be displayed if an image is loaded
to an FPGA, because the hardware might have changed,
and the user should be informed
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mini targets are using different ENV_SIZE then standard one that's why
defconfigs should be updated to simplify config files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added support to enable CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET
and CONFIG_ENV_SECT_SIZE through Kconfig for Zynq and Zynqmp.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint OCM memory. This configuration
only has required parallel nor flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of memory. This configuration
has only required nand flash support.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch updates the ram_base to store the start address of
the first bank DRAM and the use this ram_base to calculate ram_top
properly. This patch fixes the erroneous calculation of ram_top
incase of non zero ram start address.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why
there is no reason to depend on this address anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog can be started before probe and u-boot should just take control
over it. That's why do not stop watchdog in probe to cover cases where
watchdog can expire before probe and start.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added support of mmio read and write commands. These commands
can be used to read and write registers from the u-boot command line.
It can be useful in debugging.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable led support for boards which have "gpio-leds" node.
And also for microblaze which is converted to DM_GPIO now.
Tested on zcu100.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
IP itself has no reg/no bit which can be used for this functionality.
Add this note to the driver to make sure that none will be asking for
that. Current method is to setup 1s timeout and hang() which is done via
wdt_expire_now().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is only one chipselect on each connector.
Define it directly in board dts file.
There should be an option to use more chipselects via gpios.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx Axi wdt driver conversion to driver model & Kconfig update
for the same.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We should support watchdog reset so that WATCHDOG_RESET will function
properly.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed zynqmp command to handle subcommands with
U_BOOT_CMD_MKENT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling GPIO_DM support to have an option to use this
driver together with zynq gpio driver.
!DM part is kept there till Microblaze is cleanup which will be done
hopefully soon.
Just a note:
There is no reason to initialize uc-priv->name because it is completely
unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is storing reset vector at address 0x0.
It means soft reset can be done by just jumping to this address.
This code was in platform code but sysreset interface is providing
enough capabilities to have more options how to reset the system. It can
go from gpio reset through watchdog reset till soft reset.
The driver has not compatible string because this is cpu specific and DM
core is not able to detect compatible string in DT root that's why this
driver will be instantiated from platform code by calling
device_bind_driver(gd->dm_root, "mb_soft_reset", "reset_soft",
NULL);
It should be bind as the last reset method to ensure that hw reset is
called before this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux kernel has binding for gpio-restart node.
This patch is adding basic support without supporting any optional
properties.
This driver was tested on Microblaze system where gpio is connected to
SoC reset logic.
Output value is handled via gpios cells values.
In gpio_reboot_request() set_value is writing 1 because
dm_gpio_set_value() is capable to changing it when it is ACTIVE_LOW.
...
if (desc->flags & GPIOD_ACTIVE_LOW)
value = !value;
...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The same change as was done for zynqmp with this description:
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0= &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
<zynqmp example removed>
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for enabling the first watchdog pointed via aliases.
DT fragment:
aliases {
...
watchdog0 = &watchdog0;
watchdog1 = &watchdog_lpd;
...
};
dm tree fragment for above configuration with patch applied:
ZynqMP> dm tree
Class index Probed Driver Name
-----------------------------------------
...
watchdog 0 [ ] cdns_wdt | |-- watchdog@ff150000
watchdog 1 [ + ] cdns_wdt | `-- watchdog@fd4d0000
...
dm uclass fragment:
ZynqMP> dm uclass
...
uclass 75: watchdog
0 watchdog@ff150000 @ 7df02f40, seq -1, (req 1)
1 * watchdog@fd4d0000 @ 7df02ff0, seq 0, (req 0)
...
It is visible that index 1 is IP with seq 0 which means that FPD
watchdog (@fd4d0000) is in DT below LPD watchdog (@ff150000).
Till this patch the first watchdog found in DT was used and started
which is not enabling all possible configuration based on user request.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There should be proper bank name setup to distinguish between different
gpio drivers. Use dev->name for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Timer needs to be converted to DM but as of now it can't be called so
early because intc controller is not ready. Call it later in board_r.c.
Before this patch timer_init is called twice which is wrong.
The patch is blocking initialization before relocation.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove bogus zynq_gpio_getplat_data() and read driver data directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate gpio ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate sysreset ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_MP was added to Kconfig with enabling CONFIG_DEFINE_TCM_OCM_MMAP=y
for zynqmp boards. This option is enabled by default that's why it
shouldn't be in defconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Relocate watchdog ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
uclass name is used by dev_read_alias_seq which return seq number when
aliases are used.
Code fragment:
168 int dev_read_alias_seq(struct udevice *dev, int *devnump)
169 {
170 ofnode node = dev_ofnode(dev);
171 const char *uc_name = dev->uclass->uc_drv->name;
172 int ret;
173
174 if (ofnode_is_np(node)) {
175 ret = of_alias_get_id(ofnode_to_np(node), uc_name);
Also this patch enables DM_UC_FLAG_SEQ_ALIAS to be in sync with Linux
which is also using watchdog name for watchdog aliases.
drivers/watchdog/watchdog_core.c:215:
ret = of_alias_get_id(wdd->parent->of_node, "watchdog");
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
sysreset uclass have own do_reset function which should be used instead
of board/platform specific.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason not to use default ioremap/iounmap io functions.
The patch remove Microblaze macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.
Platform data is created when the device is bound, and survives
probe/remove cycles.
Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."
Based on description the driver needs to be switch to use platdata
instead of priv.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Driver supports only one instance of usb keyboard.
Remove the first dependency on generic usbkbd DEVNAME.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot needs to link ps7_init_gpl.c on Zynq or psu_init_gpl.c on
ZynqMP (PS init for short). The current logic to locate this file for
both platforms is:
1. if a board-specific file exists in
board/xilinx/zynq[mp]/$(CONFIG_DEFAULT_DEVICE_TREE)/ps?_init_gpl.c
then use it
2. otherwise use board/xilinx/zynq/ps?_init_gpl.c
In the latter case the file does not exist in the U-Boot sources and
must be copied in the source tree from the outside before starting the
build. This is typical when it is generated from Xilinx tools while
developing a custom hardware. However making sure that a
board-specific file is _not_ found (and used) requires some trickery
such as removing or overwriting all PS init files (e.g.: the current
meta-xilinx yocto layer).
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PS init file binary
* overwriting or deleting files in the source tree is ugly as hell
Simplify usage by allowing to pass the path to the desired PS init
file in kconfig variable XILINX_PS_INIT_FILE. It can be an absolute
path or relative to $(srctree). If the variable is set, the
user-specified file will always be used without being copied
around. If the the variable is left empty, for backward compatibility
fall back to the old behaviour.
Since the issue is the same for Zynq and ZynqMP, add one kconfig
variable in a common place and use it for both.
Also use the new kconfig help text to document all the ways to give
U-Boot the PS init file.
Build-tested with all combinations of:
- platform: zynq or zynqmp
- PS init file: from XILINX_PS_INIT_FILE (absolute, relative path,
non-existing), in-tree board-specific, in board/xilinx/zynq[mp]/
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
86 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
87 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
88 #endif
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
command_ret_t enum contains 3 return values but only two are handled
now. Extend cmd_process_error() and handle CMD_RET_USAGE separately.
These commands are affected by this change.
cmd/demo.c
cmd/efi.c
cmd/gpio.c
cmd/qfw.c
cmd/x86/fsp.c
test/dm/cmd_dm.c
And scripts shouldn't be affected because return value is not 0. But
every command implementation can choose what it is correct to pass.
I would expect that RET_USAGE is called when parameters are not
correctly passed (have incorrect value, missing parameters)
and RET_FAILURE when correct parameters are passed but command fails.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
Enable ums command for zcu100 to enable mass storage gadget.
Tested with ums 0 mmc 0 (for SD) and ums 0 usb 0 (for USB flashdisk).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Libretech ALL-H3-CC has a high density connector for attaching
an eMMC module. The module form factor and connection is specific
to Libretech, and has provisions for split vmmc/vqmmc (core and I/O)
voltage supplies, but this board does not wire the vqmmc side. The
H2+/H3/H5 SoCs do not support alternate I/O voltages for eMMC either.
Only 3.3V is supported. A specific module that ties vqmmc to vmmc,
with both at 3.3V, must be used.
Given that a) eMMC is not designed to be hotplugged, b) power is
always provided on the pins, and c) MMC controllers can deal with
missing cards, we can enable this by default. If a module is attached
it will be picked up by the system.
The device tree change was also submitted to the Linux Kernel and
has already been queued up for 4.19.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This commit adds the following flashes to the id-table
- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.
This patch added support to read JEDEC id in xilinx_spi_xfer ().
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch modify xilinx_spi_xfer() function and add rxfifo() and
txfifo() functions to add the modularity so that these functions
can be used by other functions within the same file.
This patch also added support to read fifo_size from dts.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add a device tree node for the Allwinner R40/V40 GMAC gigabit
ethernet interface.
The R40 SoC does not use the syscon register for GMAC settings.
The gigabit ethernet interface can only be routed to a fixed set of
pins.
Updated to match the Linux kernel's device tree.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Add support for the GMAC found in the Allwinner R40/V40 SoC.
The R40 GMAC interface is not controlled by the syscon register but
has a separate configuration register in the CCU.
The clock gate and reset bits are in a different register compared
to the other SoCs supported by this driver.
The driver uses the -gmac suffix for the R40 because the R40 also
has a different 100 MBit MAC (EMAC).
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Use driver data->variant information to select device specific
pin mux and phy clock settings.
Suggested by Jagan Teki
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Use the driver model for MMC and SATA, in preparation for CONFIG_BLK
defaulting to y.
Tested on A10 Cubieboard.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Commit dd27918c22 ("dm: mmc: sunxi: Add support for driver model")
only added the allwinner,sun5i-a13-mmc compatible string for this
driver. The DM initialisation code here also works with (at least) A10
and A20, so add the appropriate compatible strings as per Linux 4.17's
driver.
Tested on A10 Cubieboard and A20 pcDuino3 Nano with CONFIG_DM_MMC.
(A20 worked already, because sun7i-a20.dtsi specifies both the A13 and
A20 strings.)
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When the defconfig for the SoPine baseboard was added, there wasn't any
proper DT for the board yet, so we used the Pine64 DT as a placeholder.
Copy the DT file(s) meanwhile added in Linux over to U-Boot, and use
them in our defconfig.
This is as of v4.18-rc3, exactly Linux commit:
commit 7d556bfc49adddf2beb0d16c91945c3b8b783282
Author: Jagan Teki <jagannadh.teki@gmail.com>
Date: Mon Dec 4 10:23:07 2017 +0530
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H3 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 721afaa2aeb860067decdddadc84ed16f42f2048 (HEAD)
Merge: 7c00e8ae041b 87815dda5593
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Mon Jun 11 17:57:38 2018 -0700
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
This also includes the OrangePi Zero .dts, which technically has an
Allwinner H2+ SoC.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file for the various boards with an Allwinner H5 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit af5d05bdc99c211729cba0a3d5417bccfa308caf
Author: Neil Armstrong <narmstrong@baylibre.com>
Date: Tue Apr 24 13:47:14 2018 +0200
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the device tree files from the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit 55c5ba5e49a0a124ed416880e8227b493474495e
Author: Chen-Yu Tsai <wens@csie.org>
Date: Tue Apr 24 19:34:22 2018 +0800
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
Since the H3 and H5 are very similar (aside from the actual ARM cores),
they share most the SoC .dtsi and thus have to be updated together.
One tiny change is the removal of the "arm/" prefix from the include
path in the sun50i-h5.dtsi, which is needed because we don't share the
same sophisticated DT directory layout of Linux.
Also we need to fix up the board .dts files already, since the .dtsi
removes some pins, so the .dts can't reference them anymore. This is to
maintain bisectability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts files for the various boards with an Allwinner A64 SoC.
This is as of v4.18-rc3, exactly Linux commit:
commit 818668055c9d588c9a9d151e3b258ed1adacba0b
Author: Jagan Teki <jagan@amarulasolutions.com>
Date: Mon Apr 23 12:02:39 2018 +0530
arm64: dts: allwinner: a64: bananapi-m64: add usb otg
It updates the existing DT files, adds the newly added axp803.dtsi and
removes our temporary kludge file to get Ethernet support in U-Boot.
I left the amarula-relic alone, as this DT has not reached mainline yet.
The changes are not critical anyway, and the next sync will fix this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Updates the device tree file from the the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit c1cff65f9b16b31e731e2e75bbe06638c86e1996
Author: Harald Geyer <harald@ccbib.org>
Date: Thu Mar 15 16:25:08 2018 +0000
arm64: dts: allwinner: a64: add simplefb for A64 SoC
This also pulls in the newly required include files for the clock and
reset bindings, also removes the now redundant part from our
*-u-boot.dtsi overlay file.
I kept the PWM node from U-Boot, as we recently gained this explicitly
for U-Boot's own usage and I don't want to regress here. This node is in
the queue for mainline Linux already, so the next sync will make it all
equal again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
CONFIG_SPL_RESET_SUPPORT has been renamed to CONFIG_SPL_DM_RESET, update
this Kconfig file.
Fixes: bfc6bae8fa ("reset: Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET")
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Fix compilation warning when enable CONFIG_DEBUG_UART.
arch/arm/mach-socfpga/spl_s10.c: In function ‘board_init_f’:
arch/arm/mach-socfpga/spl_s10.c:146:2: warning: implicit declaration of function ‘debug_uart_init’; did you mean ‘part_init’? [-Wimplicit-function-declaration]
debug_uart_init();
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
MCR instruction only available in ARM 32-bit. So, compile MCR instruction
when ARM 32-bit is enabled.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Commit 5dfd5607af2114047bd ("ARM: socfpga: Pull DRAM size from DT") get
memory size from DT. So, we need to update memory size in memory node.
Otherwise, it cause U-boot hang.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but the master is idle, and stop is detected
(SDF set).
This patch addes a handling to re-init the lpi2c master for this
case. Then the issue can be worked around.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command. This causes a problem when reading register
data from i2c device.
Generally two operations comprise the register data reading:
1. Write the register address to i2c device.
START | chip_addr | W | ACK | register_addr | ACK |
2. Read the Data from i2c device.
START | chip_addr | R | ACK | DATA | NACK | STOP
The STOP command should happen at the end of the transfer, otherwise
we will always get data from register address 0
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LPI2C master. As a result, we can never see the falling edge
of the ninth clock.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Make sure the ARM ACTLR register has correct configuration, otherwise
the Linux kernel refuses to boot. In particular, the "Write Full Line
of Zeroes" bit must be cleared.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The SPL can also parse the DRAM configuration node to figure out the
memory layout, make sure it is available.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The SDRAM must first be rewritten by zeroes if ECC is used to initialize
the ECC metadata. Make the CPU overwrite the DRAM with zeroes in such a
case. This scrubbing implementation turns the caches on temporarily, then
overwrites the whole RAM with zeroes, flushes the caches and turns them
off again. This provides satisfactory performance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This function was never used in SPL and the default implementation of
dram_bank_mmu_setup() does the same thing. The only difference is the
part which configures OCRAM as cachable, which doesn't really work as
it covers more than the OCRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Add do_bridge_reset() function for Arria 10, it is required by misc.c.
arch/arm/mach-socfpga/built-in.o: In function `do_bridge':
arch/arm/mach-socfpga/misc.c:221: undefined reference to `do_bridge_reset'
make[1]: *** [u-boot] Error 1
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add build support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-socfpga/Kconfig
Restructure the SPL so each devices such as CV, A10 and S10
will have their own dedicated SPL file. SPL file determine
the HW initialization flow which is device specific
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Use "%p" to print cmdbuf.
Compilation warning as below:
CC spl/drivers/spi/cadence_qspi_apb.o
LD spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
cmdlen, (unsigned int)cmdbuf);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Use "%zu" for size_t data type.
Compilation warning as below:
In file included from include/linux/bug.h:7:0,
from include/common.h:26,
from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
By checking ubifs source code, s_instances parameter is not
used anymore. So, set this parameter and the associated source
code under __UBOOT__ compilation.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When trying to attach an UBI MTD partition via "ubi part", it may happen
that the MTD partition defined in U-Boot (via mtdparts) is not big
enough than the one, where the UBI device has been created on. This
may lead to errors, which are not really descriptive to debug and
solve this issue, like:
ubi0 error: vtbl_check: too large reserved_pebs 1982, good PEBs 1020
ubi0 error: vtbl_check: volume table check failed: record 0, error 9
or:
ubi0 error: init_volumes: not enough PEBs, required 1738, available 1020
ubi0 error: ubi_wl_init: no enough physical eraseblocks (-718, need 1)
ubi0 error: ubi_attach_mtd_dev: failed to attach mtd1, error -12
Lets add an additional message upon attach failure, to aid the U-Boot
user to solve this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
When using static volumes, the file size stored in the volume is
determined at runtime. Currently the ubi command prints the file
size specified on the console, which leads to a rather confusing
series of messages:
# ubi read ${fdt_addr_r} testvol
Read 0 bytes from volume testvol to 82000000
No size specified -> Using max size (179924992)
Make sure to print the actual size read in any case:
# ubi read ${fdt_addr_r} testvol
No size specified -> Using max size (179924992)
Read 179924992 bytes from volume testvol to 82000000
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In the device tree, the address for the led is located
in the parent node (for exemple leds), not in the led node
(for exemple led@0).
The commit "led: bcm6328: convert to use live dt"
(sha1: 8994551760)
change this behaviour and read the address in the led node.
We fix this by reading the base address for led
in the parent node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
In the device tree, the address for cpu is located in
the node "cpus", not in the cpu node (for exemple cpu@0).
So when probing cpu, the cpu address must be read in the
cpu parent.
The commit "cpu: bmips: convert to use live dt"
(sha1: c444afbbef)
change this behaviour and read the address in the
cpu node when probing cpu.
We fix this by reading the address in the cpu parent.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that Travis CI is building with gcc-7.3.0, we can add
build coverage for all combinations of MIPS Release 6
instruction sets (MIPS32, MIPS64, Big Endian, Little Endian).
Add mew default configs for Boston board for all MIPS Release 6
variants.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Since commit f916757300 (imx: Create distinct pre-processed mkimage
config files), *.cfgtmp files are no longer generated. There is no need
to remove them on the 'clean' target anymore.
Rename the .gitignore glob to *.cfgout.
Cc: Trent Piepho <tpiepho@impinj.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
When generating timestamps in signatures, use imagetool_get_source_date()
so we can be overridden by SOURCE_DATE_EPOCH to generate reproducible
images.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
So we can use imagetool_get_source_date() from callers who do not have
the image tool params struct, just pass in the command name for the error
message.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
In ARM 64-bits, memory size can be supported is more than 4GB,
hence increasing save array is needed to cope with testing larger memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Newer kernels have moved from ttyO0 to ttyS0, and when booting
it drops a notice:
WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
This ensures that you still see kernel messages. Please
update your kernel commandline.
This patch updates the console to use ttyS0 and eliminate the
chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
Typically init_scsi() does not output anything. So initr_scsi() should
provide a \n or we may see borked output like
SCSI: Net: No ethernet found.
as observed with sandbox_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The omap_gpio driver has a TODO that says when every board is converted
to DM and DT, the omap_gpio_bind can stop using calloc and switch
to auto-alloc.
This patch converts this driver to auto-calloc when DT is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
The hashed-strings signature property includes two uint32_t values.
The first is unneeded as there should never be a start offset into the
strings region. The second, the size, is needed because the added
signature node appends to this region.
See tools/image-host.c, where a static 0 value is used for the offset.
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new config value FIT_SIGNATURE_MAX_SIZE, which controls the
max size of a FIT header's totalsize field. The field is checked before
signature checks are applied to protect from reading past the intended
FIT regions.
This field is not part of the vboot signature so it should be sanity
checked. If the field is corrupted then the structure or string region
reads may have unintended behavior, such as reading from device memory.
A default value of 256MB is set and intended to support most max storage
sizes.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Teddy Reed <teddy.reed@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Verification of hashes needs to take place before any image post
processing, thus matching full FIT image processing.
This allows mechanisms such as encryption be applied to images
prior to fit generation at the spl level.
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Move the FPGA loading from IS_ENABLED(CONFIG_SPL_OS_BOOT) &&
IS_ENABLED(CONFIG_SPL_GZIP) conditional. The FPGA loading can
be used without OS loading and GZIP support in SPL. This issue
was most likely induced by some merge conflict, so fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Handle the case where the full fitImage support is enabled. In this
case, the whole fitImage must be loaded up front as some parts of the
fitImage code require memory-mapped access to the entire fitImage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Rather than verifying configuration signature of the configuration node
containing the kernel image types, verify all configuration nodes, even
those that do not contain kernel images. This is useful when the nodes
contain ie. standalone OSes or U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The openssl command specified in test_with_algo() ultimately ends up
being run by RunAndLog::run(), which uses it to construct a Popen object
with the default shell=False. The stderr redirect in the command is
therefore simply passed to openssl as an argument. With at least openssl
1.1.0f this causes openssl, and therefore test_vboot, to fail with:
genpkey: Use -help for summary.
Exit code: 1
Any stderr output ought to be captured & stored in the RunAndLog
object's output field and returned from run() via run_and_log() to
test_with_algo() which then ignores it anyway, so we can drop the
shell-like redirection with no ill effects. With this fix test_vboot now
passes for me.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
In python 3.x the file() function has been removed. Use open() instead,
which works on both python 2.x & 3.x, and is described as the preferred
method of opening a file by python 2.x documentation anyway.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The read_file() function in test_fit is used with files that are not
text files, as well as some that are. It is never used in a way that
requires it to decode text files to characters, so open all files in
binary mode such that read() doesn't attempt to decode characters for
files which are not text files.
Without this test_fit fails on python 3.x when reading an FDT in
run_fit_test() with:
UnicodeDecodeError: 'utf-8' codec can't decode byte 0xd0 in position
0: invalid continuation byte
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
In python 3.x the configparser module is named with all lower case.
Import it as such in order to avoid errors when running on python 3.x,
and fall back to the CamelCase version in order to keep working with
python 2.x.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
In python 3.x the xrange() function has been removed, and range()
returns an iterator much like Python 2.x's xrange(). Simply use range()
in place of xrange() in order to work on both python 2.x & 3.x. This
will mean a small cost on python 2.x since range() will return a list
there rather than an iterator, but the cost should be negligible.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
In python 3.x print must be called as a function rather than used as a
statement. Update uses of print to the function call syntax in order to
be python 3.x safe.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add code to reset all reset signals as in Ethernet DT node. A reset
property is an optional feature, so only print out a warning and do not
fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add code to reset all reset signals as in serial DT node. A reset
property is an optional feature, so do not fail if a reset property is
not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add code to reset all reset signals as in mmc DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change to use CONFIG_IS_ENABLED(DM_RESET), so this can work in SPL
build (CONFIG_SPL_DM_RESET) and U-boot build (CONFIG_DM_RESET).
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add myself as the Maintainer for Actions Semi OWL family and its
relevant board, drivers.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds Actions Semi OWL family UART support. This driver
relies on baudrate configured by primary bootloaders.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds Actions Semi OWL family base clock and S900 SoC
specific clock support. For S900 peripheral clock support, only UART
clock has been added for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This commit adds Actions Semi OWL SoC family support with S900 as the
first target SoC.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
It is useful to write the position and size of each entry back to the
device tree so that U-Boot can access this at runtime. Add a feature to
support this, along with associated tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Once binman has packed the image, the position and size of each entry is
known. It is then possible for binman to update the device tree with these
positions. Since placeholder values have been added, this does not affect
the size of the device tree and therefore the packing does not need to be
performed again.
Add a new SetCalculatedProperties method to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some entry types modify the device tree, e.g. to remove microcode or add a
property. So far this just modifies their local copy and does not affect
a 'shared' device tree.
Rather than doing this modification in the ObtainContents() method, and a
new ProcessFdt() method which is specifically designed to modify this
shared device tree.
Move the existing device-tree code over to use this method, reducing
ObtainContents() to the goal of just obtaining the contents without any
processing, even for device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present some warnings are printed to indicate failures which are a
known part of running the tests. Suppress these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add more tests to increase dtoc code coverage to 100%.
Correct a whitespace error in some test .dts files at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a -T option to run a code-coverage test on dtoc. At present this is
about 96%. Future work will increase it to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present a property with a single phandle looks like an integer value
to dtoc. Correct this by adjusting it in the phandle-processing code.
Add a test for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the algortihm is not correct since it will return the root node
if the requested node is not found and there are no slashes in the
requested node name. Fix this and add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the Fdt class does not keep track of property offsets if they
change due to removal of properties. Update the code to handle this, and
add a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only some of the fdt functionality is tested. Add more tests to
cover the rest of it. Also turn on test coverage, which is now 100% with
a small exclusion for a Python 3 feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the Fdt class has its own copy of the device tree. This is
confusing an unnecessary now that pylibfdt has its own. Drop it and
provide access functions to the buffer.
This allows us to move the rest of the implementation to use pylibfdt
methods instead of directly calling libfdt stubs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that pylibfdt supports a fuller API we don't need to directly call
the libfdt stubs. Update the code to use the Fdt methods instead.
Some other cases remain which will be tidied up in a later commit, since
they need larger changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
When a test fails due to an output mismatch (e.g. due to a new property
being adding to a test file) it is currently hard to update the test to
the new output. In particular the tabs in the file are written as \t in
the Python tests.
To make this easier, write both the expected and actual results to /tmp
to allow use of meld, and copying into the test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this module is tested via the dtoc tests. This is a bit painful
since the tests are at a higher level and so failures are more difficult
to diagnose.
Add some tests that exercise the fdt module directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only binman has the logic for determining Python test coverage
but this is useful for other tools also. Move it out into a separate file
so it can be used by other tools.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for these functions in the Python binding. This patch stands
in for a pending upstream change.
Signed-off-by: Simon Glass <sjg@chromium.org>
This currently fails to reduce the device-tree bytearray size. Fix this.
This stands in for a pending upstream change.
Signed-off-by: Simon Glass <sjg@chromium.org>
This provides various patches sent to the devicetree-compiler mailing list
to enhance the Python bindings. A final version of this patch may be
created once upstreaming is complete, but if it takes too long, this can
act as a placeholder.
New pylibfdt features:
- Support for most remaining, relevant libfdt functions
- Support for sequential-write functions
Changes are applied to existing U-Boot tools as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the contents of an entry are set in subclasses simply by
assigning to the data and content_size properties. Add some methods to do
this, so that we have more control. In particular, add a method to set the
contents without changing its size, so we can validate that case.
Add a test case for trying to change the size when this is not allowed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move all the test execution into the same mechanism so that we can request
a particular test (from any suite) by passing it as an argument to
'binman -t'.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is supposed to return the contents of an entry. However at
present there is no check that it actually does. Also some implementations
do not return 'True' to indicate success, as required.
Add a check for things working as expected, and correct the
implementations.
This requires some additional test cases to cover things which were missed
originally. Add these at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we call the three entries first, second and third. Rename them
to reflect their contents instead, for clarity.
Signed-off-by: Simon Glass <sjg@chromium.org>
This fake entry is used for testing. At present it only has one behaviour
which is to return an invalid set of entry positions, to cause an error.
The fake entry will need to be used for other things too. Allow the test
.dts file to specify the behaviour of the fake entry, so we can control
its behaviour easily.
While we are here, drop the ReadContents() method, since this only applies
to subclasses of Entry_blob, which Entry__testing is not.
Signed-off-by: Simon Glass <sjg@chromium.org>
The most portable way to get access to coverage is to invoke it as
'python-coverage'.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way to decode a memory region, including the memory type (sram or
sdram) and its start address and size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new device_bind_ofnode() function which can bind a device given its
ofnode. This allows binding devices more easily with livetree nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to show a message when logging an error return
value, perhaps to add a few details about the problem. Add a function to
support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a 32-bit version of this function. Add a 64-bit version as well so
we can easily read 64-bit ints from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support a default memory bank, specified in reg, as well as
board-specific memory banks in subtree board-id nodes.
This allows memory information to be provided in the device tree,
rather than hard-coded in, which will make it simpler to handle
similar devices with different memory banks, as the board-id values
or masks can be used to match devices.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
To build U-Boot on a Nyan Big Chromebook the docs outline adjusting the Tegra124
defined CONFIG_SYS_TEXT_BASE but this has since been moved to individual config
files. We should have the default required for U-Boot chain loading on the
chromebook as the default CONFIG_SYS_TEXT_BASE and update the docs to remove
this now non required step.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On the A64 the clock for the first USB controller is actually the parent
of the clock for the second controller, so turning them off in that order
makes the system hang.
Fix this by only turning off *both* clocks when the *last* OHCI controller
is brought down. This covers the case when only one controller is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional usb from u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
The Allwinner A64 SoCs suffers from an arch timer implementation erratum,
where sometimes the lower 11 bits of the counter value erroneously
become all 0's or all 1's [1]. This leads to sudden jumps, both forwards and
backwards, with the latter one often showing weird behaviour.
Port the workaround proposed for Linux to U-Boot and activate it for all
A64 boards.
This fixes crashes when accessing MMC devices (SD cards), caused by a
recent change to actually use the counter value for timeout checks.
Fixes: 5ff8e54888 ("sunxi: improve throughput
in the sunxi_mmc driver")
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2018-May/576886.html
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
At the moment we have the workaround for the Freescale arch timer
erratum A-008585 merged into the generic timer_read_counter() routine.
Split those two up, so that we can add other errata workaround more
easily. Also add an explaining comment on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Andreas Färber <afaerber@suse.de>
Tested-by: Guillaume Gardet <guillaume.gardet@free.fr>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ax25-ae350 target currently uses CONFIG_BOOTP_SERVERIP which means we
ignore the DHCP provided TFTP ip address. This breaks every case where we
do now provide a serverip environment variable.
Instead, let's use the new CONFIG_BOOT_PREFER_SERVERIP option to fall back
to the DHCP provided TFTP IP if no serverip environment variable is set.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Rick Chen <rick@andestech.com>
Currently we can choose between 2 different types of behavior for the
serverip variable:
1) Always overwrite it with the DHCP server IP address (default)
2) Ignore what the DHCP server says (CONFIG_BOOTP_SERVERIP)
This patch adds a 3rd option:
3) Use serverip from DHCP if no serverip is given
(CONFIG_BOOTP_PREFER_SERVERIP)
With this new option, we can have the default case that a boot file gets
loaded from the DHCP provided TFTP server work while allowing users to
specify their own serverip variable to explicitly use a different tftp
server.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We can call commands like dhcp and bootp without arguments or with
explicit command line arguments that really should tell the code where
to look for files instead.
Unfortunately, the current code simply overwrites command line arguments
in the dhcp case with dhcp values.
This patch allows the code to preserve the command line values if they
were set on the command line. That way the semantics are slightly more
intuitive.
The reason this patch does that by introducing a new variable is that we
can not rely on net_boot_file_name[0] being unset, as today it's
completely legal to call "dhcp" and afterwards run "tftp" and expect the
latter to repeat the same query as before. I would prefer not to break
that behavior in case anyone relies on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new command 'wol': Wait for an incoming Wake-on-LAN packet or
time out if no WoL packed is received.
If the WoL packet contains a password, it is saved in the environment
variable 'wolpassword' using the etherwake format (dot or colon
separated decimals).
Intended use case: a networked device should boot an alternate image.
It's attached to a network on a client site, modifying the DHCP server
configuration or setup of a tftp server is not allowed.
After power on the device waits a few seconds for a WoL packet. If a
packet is received, the device boots the alternate image. Otherwise
it boots the default image.
This method is a simple way to interact with a system via network even
if only the MAC address is known. Tools to send WoL packets are
available on all common platforms.
Some Ethernet drivers seem to pad the incoming packet. The additional
padding bytes might be recognized as Wake-on-LAN password bytes.
By default enabled in pengwyn_defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When building without FASTBOOT_FLASH we don't include the intermediate
update callback to keep the client alive, so ensure we don't try setting
it here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
phyread can timeout and val will contain random value. Initialize it to
zero not to report random value in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional video in u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
As pointed out by Wolfgang Denk, the problem with this fix is that while
interactive users will see that we have found one part of the
environment failed and are using the other, progmatic use will not see
this and can lead to problems.
Signed-off-by: Tom Rini <trini@konsulko.com>
This updates the doc to mention chain-loading an x86 kernel via
'bootefi' command, along with several typos fix.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
ACPI tables can be passed via EFI configuration table to an EFI
application. This is only supported on x86 so far.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the number of configuration tables is set to 2. By
looking at which tables the Linux EFI stub or iPXE can process,
it looks 16 is a reasonable number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
On x86 traditional E820 table is used to pass the memory information
to kernel. With EFI loader we can build the EFI memory map from it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Built without a ROM image with FSP (u-boot.rom), the U-Boot loader applies
the microcode update data block encoded in Device Tree to the bootstrap
processor but not passed to the other CPUs when multiprocessing is enabled.
If the bootstrap processor successfully performs a microcode update
from Device Tree, use the same data block for the other processors.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed build errors on edison and qemu-x86]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This adds the scsi command to coreboot and qemu, to be in consistent
with other x86 targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the introduction of early timer support in the TSC driver,
the capability of getting clock rate from device tree was lost
unfortunately. Now we bring such functionality back, but with a
limitation that when TSC is used as early timer, specifying clock
rate from device tree does not work.
This fixes random boot failures seen on QEMU targets: printing "TSC
frequency is ZERO" and reset forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On a 4.18-rc1 kernel the following warning is seen on i.MX51 and
i.MX53:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
Select the ARM_CORTEX_A8_CVE_2017_5715 workaround for i.MX51/i.MX53
to fix the problem.
With this patch applied the kernel reports:
CPU0: Spectre v2: using BPIALL workaround
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Enable CVE-2017-5715 option to set the IBE bit. This enables kernel
workarounds necessary for the said CVE.
With this enabled, Linux reports:
CPU0: Spectre v2: using BPIALL workaround
This workaround may need to be re-applied in OS environment around low
power transition resume states where context of ACR would be lost (off-mode
etc).
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable CVE_2017_5715 and since we have our own v7_arch_cp15_set_acr
function to setup the bits, we are able to override the settings.
Without this enabled, Linux kernel reports:
CPU0: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
With this enabled, Linux kernel reports:
CPU0: Spectre v2: using ICIALLU workaround
NOTE: This by itself does not enable the workaround for CPU1 (on
OMAP5 and DRA72/AM572 SoCs) and may require additional kernel patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
For ohci, the maximam supported endpoint number is 32(in and out), and
now we have used (usb_pipeendpoint(pipe) << 1) to index the specified
endpoint descritor, usb_pipeendpoint(pipe) can reach 0xf, so we need
change the NUM_EDs from 8 to 32.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
ohci-hcd casts priv_data pointer to (ohci_t *), thus it must be
the first member in private data struct.
Fixes 831cc98b1 ("usb: sunxi: Simplify ccm reg base code")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
The N25Q256(A) datasheet clearly states that this device does have
a Flag Status Register and does update FSR PEC bit 7 during Program
and Erase cycles to indicate the cycle is in progress. Enable the
FSR PEC bit polling on this device to prevent data corruption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tom Rini <trini@konsulko.com>
The claim/release bus function must not reset the whole SPI core because
settings regarding wordlen, clock-frequency and so on made by
set_wordlen, set_mode, set_speed get lost with this action. Resulting in
a non-functional SPI.
Without DM the failure didn't came up since after the spi_reset within
claim bus all the setup (wordlen, mode, ...) was called, in DM they are
called by the spi uclass.
We change now the things as following for having a working SPI instance
in DM:
- move the spi_reset(...) to the probe call in DM for having a known
hardware state after probe. Without DM we don't have a probe call, so we
issue the reset as before during the claim_bus call.
- in release bus we just reset the modulctrl to the reset-value (spi-
slave)
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This bug is the combination of dwc2 USB controller and lan78xx
USB ethernet controller, which is the combination in use on
the Raspberry Pi Model 3 B+.
When the host attempts to receive a packet, but a packet has not
arrived, the lan78xx controller responds by setting BIR
(Bulk-In Empty Response) to NAK. Unfortunately, this hangs
the USB controller and requires the USB controller to
be reset.
The fix proposed is to have the lan78xx controller respond
by setting BIR to ZLP.
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
When using a redundant environment a read error should simply mean to
not use that copy instead of giving up completely. The other copy may
be just fine.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Ioan-Adrian Ratiu <adrian.ratiu@ni.com>
For now, the existing SPL MXS NAND driver only supports to identify
ONFi-compliant NAND chips. In order to allow identifying
non-ONFi-compliant chips add `mxs_flash_full_ident()` which uses the
`nand_get_flash_type()` functionality from `nand_base.c` to lookup
for supported NAND chips in the chip ID list.
For compatibility reason the full identification support is only
available if the config option `CONFIG_SPL_NAND_IDENT` is enabled.
The lookup was tested on a custom i.MX6ULL board with a Toshiba
TC58NVG1S3HTAI0 NAND chip.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The existing `mxs_flash_ident()` is limited to identify ONFi compliant
NAND chips only. In order to support non-ONFi NAND chips refactor the
function and rename it to `mxs_flash_onfi_ident()`.
A follow-up patch will add `mxs_flash_full_ident()` which allows to use
the chip ID list to lookup for supported NAND flashs.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Add the config option `CONFIG_SPL_NAND_IDENT` for using the NAND chip ID list
to identify the NAND flash in SPL.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
`nand_get_flash_type()` allows identification of supported NAND flashs.
The function is useful in SPL (like mxs_nand_spl.c) to lookup for a NAND
flash (which does not support ONFi) instead of using nand_simple.c and
hard-coding all required NAND parameters.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Since commit 1da1938d57 ("spl: Add default values for ARCH_MX7")
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR is selected by default on
i.MX7 platforms, so remove it from the board defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
fdt_file is looking for imx6ul-geam-kit.dtb but Linux
has imx6ul-geam.dtb, since Linux skipped -kit on file name
by below commit.
"ARM: dts: imx6ul-geam: Skip suffix -kit from dts name"
(sha1: 182de5ebce71e469cfa686fcdf08c9cbe11ece97)
So, due to this mismatch U-Boot failed to pick the
proper dtb which eventually break the Linux boot.
This patch fixed this mismatch by
- renaming dts files
- update config option to use new dtb file
- update fdt_file to new dtb file name
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The PFUZE3000 uses registers addresses up to 0xff.
The DM pfuze100 driver supports both pfuze100 and pfuze3000. Allow it
to use the device type to return the correct number of registers.
Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.
This aligns behavior with the mainline driver, such that:
- If fsl,use-minimal-ecc is requested it will use data from
data sheet/ONFI. If this is not available the driver will fail.
- If nand-ecc-strength/nand-ecc-step-size are specified those
value will be used.
- By default maximum possible ECC strength is used
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Support driver data from device tree. Also support fsl,use-minimal-ecc
similar to Linux' GPMI NAND driver.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation for device tree support separate board init
from controller init similar to other raw NAND drivers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This function initializes DMA descriptors so mxs_nand_init_dma is
more precise. It also frees up the rather generic name mxs_nand_init.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Move GPMI and BCH register structs to the driver struct mxs_nand_info
in prepartion for device tree support.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Report correct ECC parameters back to the stack. Do not report
bytes as we have it not immeaditly available and the Linux version
also does not report it. It seems to have no aversive effect.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Calculate BCH geometry at start and store the information in
a structure. This avoids recalculation on every page access
and allows to calculate ECC relevant information in one place.
This patch does not change ECC layout or driver behavior in
any way.
The patch aligns the driver somewhat with the Linux GPMI NAND
driver which drives the same IP.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add config option which allows to enable on flash bad block table
support. This has the same effect as when using the device tree
property "nand-on-flash-bbt" in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.
Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation to convert the driver to use NAND self init
provide a new minimal init for SPL builds. As a side effect
this also reduces size of SPL by about 4KiB.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.
The named commit:
- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.
- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Each entry of the EFI memory descriptors occupies map->desc_size,
not sizeof(struct efi_mem_desc).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present in dram_init_banksize() it ignores conventional memory
above 4GB. This leads to wrong DRAM size is printed during boot.
Remove such limitation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable PRE_CONSOLE_BUFFER so that the full boot output can be viewed
on the video console for the EFI payload.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The use_uart assignment should follow immediately after the call to
exit_boot_services(), in case we want some debug output after that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit bb0bb91cf0 ("efi_stub: Use efi_uintn_t"), EFI x86
64-bit payload does not work anymore. The call to GetMemoryMap()
in efi_stub.c fails with return code EFI_INVALID_PARAMETER. Since
the payload itself is still 32-bit U-Boot, efi_uintn_t gets wrongly
interpreted as int, but it should actually be long in a 64-bit EFI
environment.
This changes the x86 __kernel_size_t conditionals to use compiler
provided defines instead. That way we always adhere to the build
environment we're in and the definitions adjust automatically.
Fixes: bb0bb91cf0 ("efi_stub: Use efi_uintn_t")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently efi.h determines a few bits of its environment according to
config options. This falls apart with the efi stub support which may
result in efi.h getting pulled into the stub as well as real U-Boot
code. In that case, one may be 32bit while the other one is 64bit.
This patch changes the conditionals to use compiler provided defines
instead. That way we always adhere to the build environment we're in
and the definitions adjust automatically.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: added some comments to describe the __x86_64__ check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For boards that don't route serial port pins out, it's quite common
to attach a USB keyboard as the input device, along with a monitor.
However USB is not automatically started in the generic efi payload
codes. This uses a payload specific last_stage_init() to start the
USB bus, so that a USB keyboard can be used on the U-Boot shell.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The generic efi payload currently does not enumerate the PCI bus,
which means peripherals on the PCI bus are not discovered by their
drivers. This uses board_early_init_r() to do the PCI enumeration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With driver model philosophy, we should avoid explicitly calling
driver initialization routine during boot. This updates the ram
init sequence table to exclude the IDE initialization for DM BLK.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The default vesa mode was changed since commit 55b4e1b7d9
("x86: Change default FRAMEBUFFER_VESA_MODE of some boards") for
better VxWorks compatibility but with the changes QEMU video console
no longer works. This is because QEMU's vgabios implements the VESA
mode 8:8:8 as 24bpp without an alpha channel, which U-Boot's video
console driver currently does not support yet.
We need change to real 32bpp in order to make it work again. QEMU
vgabios implements the custom 32bpp VESA mode starting from 0x140
(320x200x32) to 0x147 (1600x1200x32). Set it to 0x144 (1024x768x32).
Fixes: 55b4e1b7d9 ("x86: Change default FRAMEBUFFER_VESA_MODE of some boards")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Previous rename of efi-x86 target missed the MAINTAINERS update,
which caused the buildman warnings:
WARNING: no status info for 'efi-x86_app'
WARNING: no maintainers for 'efi-x86_app'
This updates the board MAINTAINERS to reflect the up-to-date info.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some environments require providing the '--smtp-server' argument to
'git send-email'. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test to exercise the check for a valid SPDX license.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Many mailing-lists consider a long Cc list a sign of spam and will
either drop the message or mark it for moderation. Because patman
automatically invokes get_maintainer.pl the Cc list can expand
unexpectedly. Allow the user to specify a limit for the Cc list.
This limit is applied after removing any known bouncing addresses. By
default no limit is applied.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the clock-frequency information has been moved to the
driver, more DT sync is possible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable the on-chip ethernet driver for uniphier_{v7,v8}_defconfig.
Disable the on-board SMC911x because it has not migrated to the
driver model yet - it is not possible to enable DM and non-DM
drivers at the same time.
The CONFIG_SMC911X for uniphier_ld4_sld8_defconfig is still kept
because the on-chip ethernet driver for LD4, sLD8 is not supported
yet.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Patch queue for efi - 2018-06-21
A single urgent fix to make sure green and red are not swapped
in OSs that make use of EFI GOP frame buffers to display pictures
(such as efifb in Linux).
We store pixels as BGRA in memory, as can be seen from struct efi_gop_pixel.
So we need to expose the same format to UEFI payloads to actually have them
use the correct colors.
Reported-by: Fabian Vogt <fvogt@suse.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
As many targets are now commonly built with gcc-6 or later (which
defaults to a newer C standard than older compilers), certain C
constructs are now being used as they produce more readable code. And
while all compilers that we support building with support the C11
standard (and GNU11) they do not default to that standard. Ensure that
we pass along -std=gnu11 when building.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable USB on all Amlogic Meson GXL based board.
Enable Regulator support on all boards.
Enable ADC support on the LibreTech-CC board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SARADC driver was merged after the following commit :
commit d35812368a ("regmap: change regmap_init_mem() to take ofnode instead udevice")
Thus breaking build, this patch fixes the regmap_init_mem accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
BOOT2 partition is empty and free for using to store the environment.
Use that instead of the default user partition.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The ARM64 has 2 MiB alignment requirement for the kernel. When using
fitImage, this requirement may by violated, the kernel will thus be
executed from unaligned address and fail to boot. Do what booti does
and run booti_setup() for kernel_noload images on arm64 to obtain a
suitable aligned address to which the image shall be relocated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Add option to the booti_setup() which indicates to it that the caller
requires the image to be relocated to the beginning of the RAM and
that the information whether the image can be located anywhere in RAM
at 2 MiB aligned boundary or not is to be ignored. This is useful ie.
in case the Image is wrapped in another envelope, ie. fitImage and not
relocating it but moving it would corrupt the envelope.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-By: Bin Chen <bin.chen@linaro.org>
At present the code overruns the bar[] array. Fix this.
At the same time, drop the leading / from the "/spl" path so that we can
run U-Boot SPL with:
spl/u-boot-spl
rather than requiring:
/path/to/spl/u-boot-spl
Reported-by: Coverity (CID: 131199)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
The current code might succeed on the first allocation and fail on the
second. Separate the checks to avoid this problem.
Of course, free() will never fail and the chances that (when allocating
two small areas) one will succeed and one will fail are just as remote.
But this keeps coverity happy.
Reported-by: Coverity (CID: 131226)
Signed-off-by: Simon Glass <sjg@chromium.org>
This loop never actually exits, but the way the code is written this is
not obvious. Add an explicit error check.
Reported-by: Coverity (CID: 131280)
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add explicit init of region to NULL per LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add regulator nodes and pinmux settings to the SDHI3 on E3 Ebisu
and enable HS200 mode on it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the RAVB and SH ether driver now support parsing the PHY reset
GPIOs from both the PHY nodes and the MAC nodes, move the reset GPIOs
back into the PHY nodes to minimize DT difference between U-Boot and
Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The current state of RAVB driver expects the PHY reset GPIO in the
RAVB mode, move it back from the PHY node to avoid breakage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The latest ATF puts the U-Boot at 0x50000000, just like on all the other
boards. Adjust the text base to reflect that change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The sh_pfc_{read,write}() must operate on the register address directly
rather than on an offset, fix this to prevent illegal access.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both putc() and puts() can be called before global_data is set up. Some of
the code paths don't handle this correctly. Add an explicit test before
any member is accessed.
Reported-by: Coverity (CID: 169030)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There are multiple GPIO banks with up to 32 pins / bank. When
using 'gpio status -a' to read the pins, this patch displays
both GPIO<bank>_<index> similar to how the device trees
display in addition to displaying gpio_#
Signed-off-by: Adam Ford <aford173@gmail.com>
When CMD_GPIO is enabled the command 'gpio status -a' can cause
a hang or reboot if GPIO banks are not enabled, because it scans
all banks. This patch enables all GPIO banks so 'gpio status -a'
can fully execute.
Signed-off-by: Adam Ford <aford173@gmail.com>
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d0 ("block: Have BLOCK_CACHE default to y in some cases")
Signed-off-by: Adam Ford <aford173@gmail.com>
When an exception or interrupt occurs the link register (LR) may
contain the source of the exception, although we do not print the
value it may still be extracted with a debugger. When in SPL we
loop on getting and exception, but use a linking branch, which
over-writes the LR value, use a regular branch instruction here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
This is the case when reading freshly created filesystem.
The error message is like the following:
btrfs_read_superblock: No valid root_backup found!
Since the data from super_roots/root_backups is not actually used -
decided to rework btrfs_newest_root_backup() into
btrfs_check_super_roots() that will only check if super_roots
array is valid and correctly handle empty scenario.
As a result:
* btrfs_read_superblock() now only checks if super_roots array is valid;
the case when it is empty is considered OK.
* removed root_backup pointer from btrfs_info,
which would be NULL in case of empty super_roots.
* btrfs_read_superblock() verifies number of devices from the superblock
itself, not newest root_backup.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
Follow Linux commit 10b62a2f785a (".gitignore: move *.dtb and *.dtb.S
patterns to the top-level .gitignore").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Follow Linux commit 1377dd3e2987 (".gitignore: sort normal pattern
rules alphabetically").
This would allow us to easily catch duplicated patterns if any.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add dump trace command which dump all trace
buffer content in a much more readable fashion
than md.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The header definitions are needed for reading
record information in cmd/iotrace.c
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Run AVB 2.0 full verification chain, avb verify
2. Check if 'avb get_uuid' works, compare results with
'part list mmc 1' output
3. Test `avb read` commands, which reads N bytes from a partition
identified by a name
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
1. Add vbmeta partition info to android partition layout for TI
platforms.
2. Add support of AVB 2.0 (including avb subset of commands) for am57xx HS
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
[trini: Move to include/environment/ti/boot.h, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
1. Add initial support of boot states mode (red, green, yellow)
2. Add functions for enforcing dm-verity configurations
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Enable a "avb" command to execute Android Verified
Boot 2.0 operations. It includes such subcommands:
avb init - initialize avb2 subsystem
avb read_rb - read rollback index
avb write_rb - write rollback index
avb is_unlocked - check device lock state
avb get_uuid - read and print uuid of a partition
avb read_part - read data from partition
avb read_part_hex - read data from partition and output to stdout
avb write_part - write data to partition
avb verify - run full verification chain
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Implement AVB ops on top of existing mmc subsystem API. Currently there
is a full implementation of such operations, defined by [1]
AVB2.0 specification:
.read_from_partition() - reads N bytes from a partition identified by
a name.
.write_to_partition() - Writes N bytes to a partition identified by a name.
.validate_vbmeta_public_key() - checks if the given public ‘vbmeta’
partition is trusted.
.get_unique_guid_for_partition() - Gets the GUID for a partition identified
by a string name.
As [1] specification recommends to use tamper-evident storage for storing
rollback indexes and device state (LOCKED/UNLOCKED),
currently are only stubs instead of full implementation for these ops:
.read_rollback_index() - Gets the rollback index for a given index location
.write_rollback_index() - Sets the rollback index to a given location
.read_is_device_unlocked() - Gets where the device is unlocked
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Add libavb lib (3rd party library from AOSP), that implements support of
AVB 2.0. This library is used for integrity checking of Android partitions
on eMMC.
libavb was added as it is and minimal changes were introduced to reduce
maintenance cost, because it will be deviated from AOSP upstream in the future.
Changes:
- license headers changed to conform SPDX-style
- avb_crc32.c dropped
- updates in avb_sysdeps_posix.c/avb_sysdeps.h
For additional details check [1] AVB 2.0 README.
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
The soms with 4GB ddr have a rowaddr of 16 not 15, this allows
the detection mechanism to properly identify them as 4GB.
However these soms can be populated with whatever amount of
memory the customer requests therefor we need a ram stride test.
We can not use the get_ram_size() function because not all 4GB's
of DDR is addressable on a 32-bit architecture. Therefore instead
we use a memory stride of 128MB's and look for the address that
the memory wraps. This function is used for all som types to
catch most memory configurations.
This is a revised version of Rabeeh Khoury's original code.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The get_board_rev() is not needed anymore as a generic function
for the imx53 SoC has been used instead.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change gives the opportunity to adjust Linux command line for the
imx53 device with some legacy data.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch prevents from the situation where we may end up with garbage
displayed on the LCD panel.
Such situation occurs when one performs "reboot -f" in Linux and then
stop in U-boot (or observe the garbage on the screen during boot up).
To prevent from such situation - the PWM pin is configured as GPIO and set
to LOW.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Since kernel commit 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate
into cpu and baseboard dts") the dtb name has changed.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
ARCH_MX6 has default values for SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
and SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR.
Do the same for ARCH_MX7 so that users may have a consistent
experience through the i.MX families.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
If many values differ from the defaults, overriding the full table
is simpler and more space efficient than tweaking it through
mxs_adjust_memory_params().
Signed-off-by: Mans Rullgard <mans@mansr.com>
According to the Cortex-A7 TRM, for ACTLR.SMP bit "You must ensure this bit
is set to 1 before the caches and MMU are enabled, or any cache and TLB
maintenance operations are performed".
ROM sets this bit in normal boot flow, but when in serial download mode,
it is not set.
Here we add it in u-boot as a common flow for all i.MX cortex-a7 platforms,
including mx7d, mx6ul/ull and mx7ulp.
Signed-off-by: Ye Li <ye.li@nxp.com>
[fabio: adapted to U-Boot mainline codebase and make checkpatch happy]
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Without this change the following warning shows up when building:
board/liebherr/display5/display5.c:270:3:
warning: implicit declaration of function ‘eth_env_set_enetaddr’ [-Wimplicit-function-declaration]
This commit fixes this issue.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GPT and restore it if needed.
To test it:
display5 > mmc write 0x12000000 4 8
It will overwrite the primary GPT table.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Test case:
The fitImage gets corrupted:
truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset
[board shall hang in SPL with
"Trying to boot from MMC1" information]
Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To enter the special mode, one needs to short cut two pads with e.g. screw
driver.
After power up the SPL will execute u-boot in which proper actions will be
taken.
It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.
It removes the support for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reason).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Force booting through u-boot proper when environment error encountered
(as a result of either broken SPI-NOR or erased envs).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
It may be necessary to update the content of the whole SPI-NOR memory at
once with using a single command (tftp_sf_img).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To test if this partition is present - one needs to write:
display5 > sf probe; mtdparts
display5 > sf erase factory +0x100000
Signed-off-by: Lukasz Majewski <lukma@denx.de>
When BOOT_FROM = FACTORY, then the LEG's factory setup is performed.
This code relies on boot_nfs u-boot command, so it shall be adjusted
appropriately (e.g. provide proper fitImage file).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Currently when EFI application boots, it says:
CPU: x86_64, vendor <invalid cpu vendor>, device 0h
Fix this by calling x86_cpu_init_f() in arch_cpu_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This turns on the EFI framebuffer driver support so that a graphics
console can be of additional help.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a DM video driver for U-Boot as the EFI payload. The driver
makes use of all necessary information from the passed EFI GOP info
to create a linear framebuffer device, as if it were initialized by
U-Boot itself.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
If UEFI BIOS has the graphics output protocol (GOP), let's pass its
information to U-Boot payload so that U-Boot can utilize it (eg:
an EFI framebuffer driver).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic EFI payload support, drop EFI-specific test
logics in BayTrail Kconfig and codes, and all BayTrail boards too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that we have generic EFI payload support for all x86 boards,
drop the QEMU-specific one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds arch_cpu_init() to the payload codes, in preparation for
supporting a generic efi payload.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the EFI application and payload support codes in the x86
directory is distributed in a hybrid way. For example, the Kconfig
options for both app and payload are in arch/x86/lib/efi/Kconfig,
but the source codes in the same directory get built only for
CONFIG_EFI_STUB.
This refactors the codes by consolidating all the EFI support codes
into arch/x86/cpu/efi, just like other x86 targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit f3b5056c4e ("efi_loader: split README.efi into two
separate documents"), the original README.efi was renamed to
README.u-boot_on_efi, but x86 doc still refers to the old one.
This updates the x86 doc to reference both README.u-boot_on_efi and
README.uefi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
UEFI specifies the calling convention used in Microsoft compilers;
first arguments of a function are passed in (%rcx, %rdx, %r8, %r9).
All other compilers use System V ABI by default, passing first integer
arguments of a function in (%rdi, %rsi, %rdx, %rcx, %r8, %r9).
These ABI also specify different sets of registers that must be preserved
across function calls (callee-saved).
GCC allows using the Microsoft calling convention by adding the ms_abi
attribute to a function declaration.
Current EFI implementation in U-Boot specifies EFIAPI for efi_main()
in the test apps but uses default calling convention in lib/efi.
Save efi_main() arguments in the startup code on x86_64;
use EFI calling convention for _relocate() on x86_64;
consistently use EFI calling convention for efi_main() everywhere.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Fix warning when compiling cherryhill.dts with latest DTC:
"Warning (avoid_unnecessary_addr_size): /pci/pch@1f,0: unnecessary
#address-cells/#size-cells without "ranges" or child "reg" property"
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Orange Pi Zero Plus is an open-source single-board computer
using the Allwinner H5 SOC.
H5 Orangepi Zero Plus has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot
- 16MBit SPI Nor flash
- Debug TTL UART
- 1GBit/s Ethernet (RTL8211E)
- Wifi (RTL8189FTV)
- USB 2.0 Host
- USB 2.0 OTG + power supply
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Orange Pi R1 is an open-source single-board computer using the
Allwinner H2+ SOC.
H2+ Orange Pi R1 has
- Quad-core Cortex-A7
- 256MB DDR3
- micrSD slot
- 128MBit SPI Nor flash
- Debug TTL UART
- 100MBit/s Ethernet (H2+)
- 100MBit/s Ethernet (RTL8152B)
- Wifi (RTL8189ETV)
- USB 2.0 OTG + power supply
This board is very similar to the Orange Pi Zero.
The device tree file is copied from the Linux kernel 4.17.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Turning the cache off can help when experimenting with bare metal
applications, enable the cache command on V3M Eagle to make that
easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix the CPGWPR/CPGWPCR register address on V3M Eagle to unlock
access to the CPG clock control registers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Here we just add a tool for HSDK flashable images preparation
together with extensive documentation for HSDK board.
This will help real-life users to update U-Boot on the board.
HSDK board has preloader that reads SPI flash pages and searches
for a special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This function is used only inside this driver that's why should be
static.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID: zu3eg
Watchdog: Started��j� sdhci@ff160000: 0, sdhci@ff170000: 1
In: serial@ff010000
I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796bc)
What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change logic and put char to fifo till there is a space in output fifo.
Origin logic was that output fifo needs to be empty. It means only one
char was in output queue.
Also remove unused ZYNQ_UART_SR_TXEMPTY macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Coding style is checking to use BIT macros instead of shifts.
The patch is also fixing the rest of macros which should be BITs instead
of hex numbers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use u32 instead of int for max_bank, bank_min and bank_max. These values
can't be negative that's why no reason to use signed type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There should be return value check from zynqmp_mmio_read() in
zynqmp_mmio_rawwrite() to make sure that errors are propagated properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
calloc() can fail and return NULL. The patch is checking return value
and return in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Code around tuning_loop_counter variable expects to go below zero.
That's why this variable can't use unsigned type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The value of PMUFW_INIT_FILE is prefixed with "$(srctree)/", thus
forcing it to be a relative path inside the U-Boot source tree. Since
the PMUFW is a binary file generated outside of U-Boot, the PMUFW
binary must be copied inside the U-Boot source tree before the
build.
This generates a few problems:
* if the source tree is shared among different out-of-tree builds,
they will pollute (and potentially corrupt) each other
* the source tree cannot be read-only
* any buildsystem must add a command to copy the PMUFW binary
* putting an externally-generated binary in the source tree is ugly
as hell
Avoid these problems by accepting an absolute path for
PMUFW_INIT_FILE. This would be as simple as removing the "$(srctree)/"
prefix, but in order to keep backward compatibility we rather use the
shell and readlink to get the absolute path even when starting from a
relative path.
Since 'readlink -f' produces an empty string if the file does not
exist, we also add a check to ensure the file configured in
PMUFW_INIT_FILE exists. Otherwise the build would exit successfully,
but produce a boot.bin without PMUFW as if PMUFW_INIT_FILE were empty.
Tested in the 12 possible combinations of:
- PMUFW_INIT_FILE empty, relative, absolute, non-existing
- building in-tree, in subdir, in other directory
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function is required for adding bootstage support.
Also enable it directly for ZynqMP R5 configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch splits the current mini emmc configuration into emmc0
and emmc1 configurations because emmc is probed at boot time and on
systems which have only one interface mini configuration is failing on
unused interface. This patch also adds required clock node in dts and
enables CONFIG_MMC_SDHCI_ZYNQ through defconfig.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Point the $loadaddr variable and default load address to a more sane
area, 384 MiB from the start of RAM. This is to avoid all the reserved
memory at the beginning of RAM. The old behavior could still be easily
retained by "setenv loadaddr 0x48080000" . The new setup allows us to
use for example modern fitImage with kernel_noload, so use this as a
new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The CONFIG_SYS_CLK_FREQ is not used on some of the Gen3 boards,
remove it. Moreover, on Ebisu this actually didn't match the
comment in the config file at all, but since it was not used,
there was no real problem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Patch queue for efi - 2018-06-14
A few minor fixes for the release:
- Compile fixes
- HI20 relocations for RISC-V
- Fix bootefi without load path
- Fix Runtime Services with certain compilers
struct sunxi_ccm_reg doesn't have ahb_reset0_cfg on sun4i and sun5i,
thus compilation fails with:
drivers/usb/host/ohci-sunxi.c:96:26: error: 'struct sunxi_ccm_reg' has
no member named 'ahb_reset0_cfg'
Access this reg using its offset to fix this issue.
Fixes commit 1ed9c1118 ("usb: sunxi: ehci: get rid of ifdefs")
and commit 56830cee3 ("usb: sunxi: ohci: get rid of ifdefs")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
When we boot using memdp (bootefi on an address without previous
load that populates the device path) then the memory device path
we pass in is not backed by any handle.
That can result in weird effects. For example grub gets very grumpy
about this inside the efi_net module and just loops endlessly.
So let's expose a simple handle that the memory device path is backed
on. That way any code that looks for the device the dp is on, finds
one.
Signed-off-by: Alexander Graf <agraf@suse.de>
When U-Boot is built with 'make -j' there is not guarantee that targets in
directory arch/ are built before targets in directory lib/. The current
build instruction for EFI binaries in lib/ rely on dependencies in arch/.
If $(EFI_CRT0) or $(EFI_RELOC) is not yet built before trying to build
%.efi an error
*** No rule to make target '%.efi'
occurs.
With the patch separate copies of $(EFI_CRT0) and $(EFI_RELOC) named
efi_crt0.o and efi_reloc.o are built in lib/efi_loader and
lib/efi_selftest.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When building with -pedantic the current definition of EFI_GUID() causes
an error 'initializer element is not constant'.
Currently EFI_GUID() is used both as an anonymous constant and as an
intializer. A conversion to efi_guid_t is not allowable when using
EFI_GUID() as an initializer. But it is needed when using it as an
anonymous constant.
We should not use EFI_GUID() for anything but an initializer. So let's
introduce a variable where needed and remove the conversion.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
These constants are defined in arch-specific code but redefined here. Add
a TODO to clean this up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We currently handle the UEFI runtime reset / power off case handling via
a switch statement. Compilers (gcc in my case) may opt to handle these via
jump tables which they may conveniently put into .rodata which is not part
of the runtime section, so it will be unreachable when executed.
Fix this by just converting the switch statement into an if/else statement.
It produces smaller code that is faster and also correct because we no
longer refer .rodata from efi runtime code.
Reported-by: Andreas Färber <aferber@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The PE standard allows for HI20/LOW12 relocations. Within the efi_loader
target we always know that our relocation target is 4k aligned, so we
don't need to worry about the LOW12 part.
This patch adds support for the respective relocations. With this and a
few grub patches I have cooking in parallel I'm able to run grub on RISC-V.
Signed-off-by: Alexander Graf <agraf@suse.de>
Functions can return NULL in case of error that's why checking return
value is needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In case of phyread()/phy_setup_op() timeout code is working with
uninitialized phyreg variable. Initialize this variable to make sure
that code it not working with random value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
wait_for_bit_le32 returns negative value on failure. Fix phy...() to
handle these failures properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Combine repeated code from smi_reg_read/smi_reg_write into a common
function smi_wait_ready.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On the SPEAr600 SoC, which has the dwmac1000 variant of the IP block,
the DMA reset never succeeds when a MII PHY is used (no problem with a
GMII PHY). The designware_eth_init() function sets the
DMAMAC_SRST bit in the DMA_BUS_MODE register, and then
polls until this bit clears. When a MII PHY is used, with the current
driver, this bit never clears and the driver therefore doesn't work.
The reason is that the PS bit of the GMAC_CONTROL register should be
correctly configured for the DMA reset to work. When the PS bit is 0,
it tells the MAC we have a GMII PHY, when the PS bit is 1, it tells
the MAC we have a MII PHY.
Doing a DMA reset clears all registers, so the PS bit is cleared as
well. This makes the DMA reset work fine with a GMII PHY. However,
with MII PHY, the PS bit should be set.
We have identified this issue thanks to two SPEAr600 platform:
- One equipped with a GMII PHY, with which the existing driver was
working fine.
- One equipped with a MII PHY, where the current driver fails because
the DMA reset times out.
Note: Taken from https://www.spinics.net/lists/netdev/msg432578.html
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When connecting to from a CPU direct to a 88e6097 typically RGMII is
used. In order for traffic to actually pass we need to force the link up
so the CPU MAC on the other end will see the link.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add driver for Socionext AVE ethernet controller that includes MAC and
MDIO bus supporting RGMII/RMII modes.
The driver behaves the ethernet driver model (DM_ETH) with devicetree.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
VCAP tables must be initialized even if no advanced classification
is used. If no initialization is performed, then ECC error will
be observed by the user when the first packet enters the l2switch.
The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM
multi-bit ECC error.
This patch fixes the aforementioned ECC error by performing the
initialization of VCAP tables.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
That can happen if duplicate UDP packet arrived, and that's not uncommon.
Anyway, we ignore packets with rpc_id lower than last we sent for other
requests, so it makes sense to do that for read request as well.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If you send a final packet just before stopping the interface (e.g. a final
ACK as part of the UDP fastboot protocol), then that packet isn't reliably
delivered onto the wire.
Reap packets prior to stopping the interface to ensure any which are
in-flight make it out. Also remove buffer and len from the call to
cpdma_process() as we weren't using them on their return.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Global variable "net_state" is used in net_loop() state-machine.
But it happens that some times the net_loop() can be called
multiple times in the same call stack. For example when the
netconsole is enabled and we print the message while some other
net protocol is in action. Netconsole will overwrite the "net_state"
and that will break the logic for earlier started protocol.
To protect the state save and restore "net_state" variable each
time when we enter and exit net_loop().
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Cortina CS4223 10G PHY
- As per the CS4223 specs, an EEPROM module is
connected to the PHY. At startup the PHY reads
the firmware line and tries to load the firmware
into the internal memory.
- This driver reads the EEPROM status
and checks if firmware has been loaded
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Put the enetaddr data in the same order as it was before the change in
commit ace1520cb5 ("net: sunxi-emac: Write HW address via function")
Reported-by: Udo Maslo <u.maslo@web.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Bus translations should be applied when reading the address of the sgmii
phy registers from the DT. Use ofnode_get_addr_index instead of the
plain ofnode_read_u32_default to fix this.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On devices that have their first network interface provided by a FPGA,
the initialization of further interfaces will fail if the FPGA is not
yet programmed. This leads to problems during factory setup when the
data is supposed to be loaded over secondary netowork interfaces.
To avoid this, use the uclass_{first,next}_device_check functions to
initialize as many ethernet devices as possible.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The pin used for HDMI HPD should be set to GPIO mode on DRA76, similarly
to all the other DRA7 and AM5 SoCs.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When reading the config file, or a script file, use getline rather than
fgets so line lengths aren't limited by the size of a compiled in buffer
(128 characters for config, 1024 for scripts).
Rename 'dump' to 'line' so it's clear we're working with a line of text.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The am3517-evm boards stores the environment in NAND, but after merging
various configs, the board was trying to load environment variables from
FAT which would ultimately fail and cause some chatter.
This patch removes the ENV_IS_IN_FAT flag to eliminate the noise.
Signed-off-by: Adam Ford <aford173@gmail.com>
This causes errors when translating logical addresses to physical:
btrfs_map_logical_to_physical: Cannot map logical address <addr> to physical
btrfs_file_read: Error reading extent
The behavior of btrfs_map_logical_to_physical() is to stop traversing
CHUNK_TREE when it encounters first non-CHUNK_ITEM, which makes
only some portion of CHUNK_ITEMs being read.
Change it to skip over non-chunk items.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Synchronize the Linux Device Tree for Amlogic Meson GX boards from Linux 4.17.0
This will enable USB on Amlogic Meson GXL Boards like Khadas VIM, P212 or
LibreTech-CC.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After the commit 265edc03d5 ("fs/fat: Clean up open-coded sector
<-> cluster conversions"), it is hung up writing new file to FAT16
disk with more than 19 files in armv7. It is because result value
of sect_to_cluster() is not proper by casting from signed value to
unsigned value. Fix the wrong casting of sect_to_cluster().
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
On A64 OHCI1 clock source is OHCI0 clock, so we need to enable OHCI0
clock when OHCI1 is in use.
Fixes commit dd3228170a ("usb: sunxi: Switch to use generic-phy")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Add Panther Point chipset interrupt pin/PIRQ information, and
enable the generation of PIRQ routing table and MP table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently both pirq_reg_to_linkno() and pirq_linkno_to_reg() assume
consecutive PIRQ routing control registers. But this is not always
the case on some platforms. Introduce a new device tree property
intel,pirq-regmap to describe how the PIRQ routing register offset
is mapped to the link number and adjust the irq router driver to
utilize the mapping.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The "intel,pirq-link" property in Intel IRQ router's dt bindings
has two cells, where the second one represents the number of PIRQ
links on the platform. However current driver does not parse this
information from device tree. This adds the codes to do the parse
and save it for future use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If GetMemoryMap() fails, we really want to know EFI_BITS_PER_LONG
instead of BITS_PER_LONG. A space and LF are added in places where
error message is output to improve readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If U-Boot gets used as coreboot payload all pci resources got
assigned by coreboot. If a dts without any pci ranges gets used
the dm is not able to access pci device memory. To get things
working make use of a 1:1 mapping for bus <-> phy addresses.
This change makes it possible to get the e1000 U-Boot driver
working on a sandybridge device where U-Boot is used as coreboot
payload.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If we use U-Boot as coreboot payload with a generic dts without
any ranges specified we fail in pci pre_probe and our pci bus
is not usable.
So convert decode_regions(..) into a void function and do the simple
error handling there.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed 'u-boot' in the commit message and checkpatch warning]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Attempting to use a toolchain that is preconfigured to generate code
for the 32-bit architecture (i386), for example, the i386-linux-gcc
toolchain on kernel.org, to compile the 64-bit EFI payload does not
build. This updates the makefile fragments to ensure '-m64' is passed
to toolchain when building the 64-bit EFI payload stub codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EFI application does not boot currently. It's due to the call
to syscon_get_by_driver_data() in cpu_init_r() maps to nowhere as
CONFIG_SYSCON is not included in the configuration.
EFI application is built as a shared library, so GCC won't complain
during the build process if some symbols are not found. GCC will
simply put these symbols into the .plt section and expect dynamic
loader to fix these up.
While we are here, remove some commands and drivers that are not
needed at present.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinctrl_ich6 driver is currently unconditionally built for all
x86 boards. Let's use a Kconfig option to control the build.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
LINK_V2N and LINK_N2V are currently defines, so they cannot handle
complex logics. Change to inline functions for future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there are 3 irq router drivers. One is the common one
and the other two are chipset specific for queensbay and quark.
However these are really the same drivers as the core logic is
the same. The two chipset specific drivers configure some registers
that are outside the irq router block which should really be part
of the chipset initialization.
Now we remove these specific drivers and make all x86 boards use
the common one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This enables the 206ax cpu driver on Intel Cougar Canyon 2 board,
so that SMP can be supported too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 206ax cpu driver does not require pre-relocation flag to work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this 206ax cpu driver is only built when FSP is not used.
This updates the Makefile to enable the build for both cases.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As README.x86 already mentions, there are two SPI flashes mounted
on Intel Cougar Canyon 2 board, called SPI-0 and SPI-1 respectively.
SPI-0 stores the flash descriptor and the ME firmware. SPI-1 stores
the actual BIOS image which is U-Boot. Building a single image with
both ME firmware and U-Boot does not make sense.
This also describes the exact flash location where the u-boot.rom
should be programmed in the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It turns out that like Braswell, Intel FSP for IvyBridge requires
SPI controller settings to be locked down, as the U-Boot ICH SPI
driver fails with the following message on Cougar Canyon 2 board:
"ICH SPI: Opcode 9f not found"
Update the SPI node property to indicate this fact.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Panther Point chipset connected to Ivybridge has xHC integrated,
imply it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes the following compiler warning:
"warning: cast from pointer to integer of different size
[-Wpointer-to-int-cast]"
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The guaranteed vid bit ranges in IACORE_VIDS MSR is actually
[22:16]. This corrects the comment for it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit
f9a88a4c1cd0 ("iASL: Enhance the -tc option (create AML hex file in C)")
in ACPICA project changed a template of the variable that is used
in the generated C-file. Now, instead of hard coded "AmlCode" the
"%s_aml_code" is in use, where the prefix is a lowered case base
name of the output file. In our case it will be "dsdt" producing
a name as "dsdt_aml_code".
The quick solution is to call sed which replaces new name by the
old one to keep compatibility with old version of iASL.
The long term solution would be to modify code to use the new name
because it is more scalable.
Cc: Robert Moore <robert.moore@intel.com>
Cc: Sami Mujawar <sami.mujawar@arm.com>
Cc: Evan Lloyd <evan.lloyd@arm.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed two sentences in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Starting with cpuid level 0x16 (Skylake-based processors)
it is possible to get CPU base freq via cpuid.
This fixes booting on a skylake based system.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: fixed wrong indention of labels]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
generic.h has changed in Linux and new addtionals functions were
added.
This commit takes the latest and greatest from Linux (v4.17-rc5)
to aid with porting drivers that utilize these functions.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This commit removes text that is exact duplicated of the text above.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
In upstream Linux kernel, the fdtfile
for this specific board is called am335x-wega-rdk.dtb
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per updated hardware documentation for
lsch3 based chips like LS2088A, 0.9v support
has been added in possible supported SoC volatges
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After the commit 9b643e312d ("treewide: replace with error() with
pr_err()"), there are some pr_err() with no line break. Add missing
line breaks.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
After the commit 9b643e312d ("treewide: replace with error() with
pr_err()"), there are some pr_err() with no line break. Add missing
line breaks.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
If building envtools, there is env directory in tools directory.
Mafe the get_default_envs.sh script exclude tools/env directory.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Add timestamp to each iotrace record to aid in debugging
of IO timing access bugs.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When dealing with a lot of IO regions, sometimes
it makes sense only to trace a specific one.
This patch adds support for region limits.
If region is not set, the iotrace works the same as it was.
If region is set, the iotrace only logs io operation that falls
in the defined region.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add WARN_ONCE definition to allow single time notification
of warnings to the user.
Taken from Linux kernel (4.17) with slight changes
(Removed __section(.data.once))
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
[trini: Drop the musb and dwc3 compat versions]
Signed-off-by: Tom Rini <trini@konsulko.com>
The documentation says this is not implemented, but it is. Update the
documentation, and clarify its operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes we have several sections which repeat the same entries (e.g. for
a read-only and read-write version of the same section). It is useful to
be able to tell these entries apart by name.
Add a new 'name-prefix' property for sections, which causes all entries
within that section to have a given name prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to see a list of regions in each image produced by
binman. Add a -m option to output this information in a '.map' file
alongside the image file.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to split an image into multiple sections,
each with its own size and position, for cases where a flash device has
read-only and read-write portions.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we set the Python path at the start of binman so we can read
modules in the 'etype' directory. This is a bit messy since it affects
'import' statements through binman.
Adjust the code to set the path locally, just where it is needed. Move
the 'entry' module in with the other base modules to help with this. It
makes more sense here anyway since it does not implement an entry type.
Signed-off-by: Simon Glass <sjg@chromium.org>
We now pass a Section object to these functions rather than an Image.
Rename the parameters to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to support multiple sections within a single image. To do this,
move most of the Image class implementation into a new Section class. An
Image contains only a single Section, but at some point we will support
a new 'section' entry, thus allowing Sections within Sections.
Use the name 'bsection' for the module so we can use 'section' for the
etype module.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow the same binary to appear multiple times in an image by using the
device-tree unit-address feature (u-boot@0, u-boot@1).
Signed-off-by: Simon Glass <sjg@chromium.org>
When summarising the builds, add the -U option to emit delta lines for
the default environment built into U-Boot at each commit.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As we're building the boards, extract the default U-Boot environment to
uboot.env so we can interrogate it later.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The format of this line has changed. Update the patman test to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
When dealing with filesystems that come from block devices we can get a
noticeable performance gain in some use cases from having the block
cache enabled. The code paths are valid in other cases when we have BLK
set and may provide wins in raw reads in some use cases, so have this be
default when BLK is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The lowlevel_init function uses r4 and r6 without preserving their
values as required by the AAPCS. Use r0 and r2 instead as these
are call-clobbered.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Code that disables the i2c slave is now in the mvtwsi i2c driver.
Platform must enable DM_I2C to use that code. Add a comment in the code
as a reminder for the planned DM_I2C migration of Turris Omnia.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Equivalent code that disables the hidden i2c0 slave already exists in
the Turris Omnia platform specific code. But this hidden i2c0 slave that
interferes the i2c bus is not board specific. Armada 38x SoCs and at
least some Kirkwood variants are affected as well. Add code to disable
this slave to the i2c bus driver to make it work on all affected
hardware.
Use the bind callback because we want this to always run at boot,
regardless of whether U-Boot uses the i2c bus.
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
I just stumbled over some cluttered UBI messages. It seems some newline
chars are missing in the current U-Boot UBI source. Lets fix this
in U-Boot as well (Linux has those fixes already).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Since commit 0e373c0ade ("spl: add SPL_RESET_SUPPORT"),
reset is supported in SPL, enable this flag for STM32F SoCs family.
This allows to remove a specific case in RCC mfd driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Split the rtc_{get,set,reset} functions so that the bodies can be used
in a DM driver.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In case of no relocation we'll just waste some space at the very end
of usable memory area. If target device has very limited amount of memory
(for example 256 kB) this loss will be pretty inconvenient.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefan Roese <sr@denx.de>
For distro-boot, the TIMEOUT directive in the boot script specifies
how long to pause in units of 1/10 sec. [1]
Commit 8594753ba0 ("menu: only timeout when menu is displayed")
corrected this by simply dividing the timeout value by 10 in
menu_interactive_choice().
I see two problems:
- For example, "TIMEOUT 5" should wait for 0.5 sec, but the current
implementation cannot handle the granularity of 1/10 sec.
In fact, it never breaks because "m->timeout / 10" is zero,
which means no timeout.
- The menu API is used not only by cmd/pxe.c but also by
common/autoboot.c . For the latter case, the unit of the
timeout value is _second_ because its default is associated
with CONFIG_BOOTDELAY.
To fix the first issue, use DIV_ROUND_UP() so that the timeout value
is rounded up to the closest integer.
For the second issue, move the division to the boundary between
cmd/pxe.c and common/menu.c . This is a more desirable place because
the comment of struct pxe_menu says:
* timeout - time in tenths of a second to wait for a user key-press before
* booting the default label.
Then, the comment of menu_create() says:
* timeout - A delay in seconds to wait for user input. If 0, timeout is
* disabled, and the default choice will be returned unless prompt is 1.
[1] https://www.syslinux.org/wiki/index.php?title=SYSLINUX#TIMEOUT_timeout
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In commit e163a931af ("cmd: gpt: backup boot code before writing MBR")
there was added the procedure for storing old boot code when doing "gpt
write". But instead of storing just backup code, the whole MBR was
stored, and only specific fields were replaced further, keeping
everything else intact. That's obviously not what we want.
Fix the code to actually store only old boot code and zero out
everything else. This fixes next testing case:
=> mmc write $loadaddr 0x0 0x7b
=> gpt write mmc 1 $partitions
In case when $loadaddr address and further memory contains 0xff, the
board was bricked (ROM-code probably didn't like partition entries that
were clobbered with 0xff). With this patch applied, commands above don't
brick the board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Alejandro Hernandez <ajhernandez@ti.com>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
This updates the LEGO MINDSTORMS EV3 boot script to try loading a
uEnv.txt file and a da850-lego-ev3.dtb device tree during boot.
Signed-off-by: David Lechner <david@lechnology.com>
This removes the unused clock and RAM config options that were cargo-
culted when this board was copied from the DA850 EVM.
Signed-off-by: David Lechner <david@lechnology.com>
This disables networking related items in the config. The EV3 does not have
any networking hardware, so this is wasted space.
Signed-off-by: David Lechner <david@lechnology.com>
This moves the UART init for LEGO MINDSTORMS EV3 to board_early_init_f().
Some console messages were not being printed because the UART was not
enabled until later in the init process.
Signed-off-by: David Lechner <david@lechnology.com>
This increases the kernel image to 4M and the rootfs image to 10M.
It is getting hard to get a kernel image to fit in 3M.
Signed-off-by: David Lechner <david@lechnology.com>
The u-boot binary sits in flash immediately before the environment.
Don't allow the binary size to grow into the environment space.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The u-boot binary sits in flash immediately before the environment.
Don't allow the binary size to grow into the environment space.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The SBx81LIFKW boards connect to the internal chassis management network
via a Marvell 88e6097 L2 switch. The chassis connections are direct
serdes on ports 8 and 9 with a RGMII interface on port 10 connected to
the CPU MAC.
For debugging purposes ports 0 and 1 are also taken out to headers on
the board. Because the debug interfaces are sometimes connected to with
straight ribbon cables we need to run them at 10Mbps.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is a series of line cards for Allied Telesis's SBx8100 chassis
switch. The CPU block is common to the SBx81GS24a, SBx81XS6, SBx81XS16
and SBx81GT40 cards collectively referred to as SBx81LIFKW in u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The mach/config.h file would helpfully define CONFIG_SYS_I2C and
CONFIG_SYS_I2C_MVTWSI if CONFIG_CMD_I2C was defined by the board. This
conflicts with the way DM_I2C works. As a transitional measure don't
automatically define these if CONFIG_DM_I2C is defined. It should be
possible to remove this once all kirkwood boards are migrated to DM.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Synchronize it with the LS-XHL board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This switches the clearfog boards to use DM based gpio and i2c
drivers. The io expanders are configured via their device-tree
entries.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: add DT i2c aliases]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The a38x sata interfaces run in ahci mode and can
be accessed via the scsi command.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: rebase on current upstream]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Some QCA988x based modules presence is not detected by the SERDES lanes,
so force this detection which will trigger the LTSSM state machine to
negotiate link.
An example of such a card is WLE900VX.
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
This flash IC is used in some chromebook models
manufactured by Bitland.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The clean_bar() function resets the SPI NOR BAR register to 0, but
does not set the flash->curr_bar to 0 , therefore those two can get
out of sync, which could ultimatelly result in corrupted flash content.
The simplest test case is this:
=> mw 0x10000000 0x1234abcd 0x4000
=> sf probe
=> sf erase 0x1000000 0x10000
=> sf write 0x10000000 0x1000000 0x10000
=> sf probe ; sf read 0x12000000 0 0x10000 ; md 0x12000000
That is, erase a sector above the 16 MiB boundary and write it with
random pre-configured data. What will actually happen without this
patch is the sector will be erased, but the data will be written to
BAR 0 offset 0x0 in the flash.
This is because the erase command will call write_bar()+clean_bar(),
which will leave flash->bank_curr = 1 while the hardware BAR registers
will be set to 0 through clean_bar(). The subsequent write will also
trigger write_bar()+clean_bar(), but write_bar checks if the target
bank == flash->bank_curr and if so, does NOT reconfigure the BAR in
the SPI NOR. Since flash->bank_curr is still 1 and out of sync with
the HW, the condition matches, BAR programming is skipped and write
ends up at address 0x0, thus corrupting flash content.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Change to use devfdt_get_addr_index() function to get fdt address.
Original code has compilation warning below:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_ofdata_to_platdata’:
drivers/spi/cadence_qspi.c:297:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->regbase = (void *)data[0];
^
drivers/spi/cadence_qspi.c:298:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
plat->ahbbase = (void *)data[2];
^
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
u-boot,dm-pre-reloc was missing from pinctrl and it's
children node. causing failure to configure pin mux
before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
If the SPDX license identifier is in the first line the shell does not
recognize which interpreter shall be used to execute the script.
Cf. https://www.kernel.org/doc/html/v4.16/process/license-rules.html
for scripts which require the '#!PATH_TO_INTERPRETER' in the first line
(...) the SPDX identifier goes into the second line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The default value with distro_bootcmd is 2 seconds, which is
reasonably fast, and provides a consistent experience across platforms
supporting distro_bootcmd.
The current bootdelay value of 0 seconds is a bit challenging to
interrupt when desired.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Marek Vasut <marex@denx.de>
When building compressed (lzop, gzip) multi-dtb fit images, the
compression tool may embed the time or umask in the image.
Work around this by manually setting the time of the source file using
SOURCE_DATE_EPOCH and a hard-coded 0600 umask.
With gzip, this could be accomplished by using -n/--no-name, but lzop
has no current workaround:
https://bugs.debian.org/896520
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Patch queue for efi - 2018-06-03
A number of fixes and feature completeness work this time around:
- Fix sunxi GOP reservation
- Fix cursor position
- Fix efi_get_variable
- Allow more selftest parts to build on x86_64
- Allow unaligned memory access on armv7
- Implement ReinstallProtocolInterface
- More sandbox preparation
Patch queue for rpi - 2018-06-03
This pull request only includes a single patch that was left
out in the last one: A fix to have the fdt stay at its original
location in RAM during boot.
The code to determine rows / cols on the screen could potentially run
into a case where it doesn't know how big the screen is. In that case,
assume 80x25.
Signed-off-by: Alexander Graf <agraf@suse.de>
The magic value that disables relocation is dependent on the CPU word
size, so the current 'ffffffff' is doing the wrong thing on aarch64.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Handles are not used at runtime. They are freed by the firmware when the
last protocol interface is uninstalled. So there is no reason to use EFI
memory when creating handles.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_mem_carve_out() is used to remove memory pages from a mapping.
As the number of pages to be removed is a 64bit type the return type
should be 64bit too.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Do not use anonymous constants when calling efi_allocage_pages.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Allocate a buffer on the stack instead of an array of uninitialized
pointers; check if GetVariable writes past the end of the buffer.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Files *.so are generated files. So the clean target should delete them.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest_block_device accesses a FAT file system.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With 'make htmldocs' we can generate a documentation if the function
comments follow the DocBook conventions.
This patch adjusts the comments for EFI boot services and provides the
DocBook template for the EFI subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This exported function should have a comment describing what it does. Also
it should really be removed in favour of device_remove(), which handles
this sort of thing now. Add a comment with a TODO.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This undocumented function relies on arch-specific code to declare a nop
weak version. Add the weak function in common code instead to avoid having
to duplicate the same function in each arch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The EFI loader code requires certain linker sections to exist. Add these
for sandbox so that the EFI loader code will link.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add an implementation of setjmp() and longjmp() which rely on the
underlying host C library. Since we cannot know how large the jump buffer
needs to be, pick something that should be suitable and check it at
runtime. At present we need access to the underlying struct as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Clarify the operation of this code with some additional comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
According to the UEFI spec unaligned memory access should be enabled on
CPUs supporting it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch implements the function unaligned_access() to reset the aligned
access flag in the system control register (SCTLR). It is called when the
bootefi command is invoked.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix SPDX identifier]
Signed-off-by: Alexander Graf <agraf@suse.de>
The UEFI spec mandates that unaligned memory access should be enabled if
supported by the CPU architecture.
This patch adds an empty weak function unaligned_access() that can be
overridden by an architecture specific routine.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a test for ReinstallProtocolInterface to the controller selftest.
As ReinstallProtocolInterface has to connect controllers to the new
interface is does not fit to the manage protocols selftest.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The ReinstallProtocolInterface boot time service is implemented.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The interface has to be checked in UninstallProtocolInterface.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Pass the correct interface when uninstalling a protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If compile with support for the efi loader we need to mark the pages
allocated for the framebuffer as reserved so the kernel won't attempt
to use them for other uses.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_get_variable() always stores an extra zero byte after the output data.
When the returned data size matches the output buffer size, the extra zero
byte is stored past the end of the output buffer.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the list of missing functionality for boottime and runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a request for the console size would be answered with a response
with less then three values, uninitialized stack memory would be
copied to the number of rows and columns of the terminal.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The definitons of the variable services are adjusted:
- use efi_uintn_t instead of unsigned long
- use u16 * instead of s16 * for Unicode strings
- correct definition of QueryVariableInfo
- rename efi_get_next_variable to efi_get_next_variable_name
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Remove a superfluous call to efi_init_obj_list() invoked by
'bootefi selftest'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Files *.efi are generated files. So the clean target should delete them.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The efi selftest and the hello application require CRT0 and RELOC to be
built.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Variables EFI_RELOC and EFI_CRT0 have to be defined to build the
EFI unit tests. This patch ensures this for the x86 architecure.
If we compile with EFI_STUB, the bitness depends on CONFIG_EFI_STUB_64BIT.
Otherwise the bitness depends on CONFIG_X86_64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
If we cannot determine the size of the serial terminal we still have
to check the parameters of efi_cout_query_mode().
Querying the size of the serial terminal drains the keyboard buffer.
So make sure we do this during the initialization and not in the midst
of an EFI application.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The test case for text output is updated to check correct updating
of the cursor position.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current coding advances the column by the number of UTF-8 bytes.
The column should be increased by one per unicode character.
The UEFI spec provides advance rules for U+0000, U+0008, U+000A,
and U000D. All other characters, including control characters
U+0007 (bel) and U+0009 (tab), have to increase the column by one.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
asm/global_data.h is already included via common.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
EFI applications like GRUB issue ANSI sequences for setting colors
and for positioning. So if the EFI subsystem is enabled, we should
also enable ANSI control sequences by default.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Instead of difference between preferred and actual image base, the
actual base is added to the fields specified in the .reloc section.
Use ImageBase from PE optional header to compute the delta,
exit early if the image is loaded at the preferred address.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds support for loading secure bitstreams on ZynqMP
platforms. The secure bitstream images has to be generated using
Xilinx bootgen tool.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to load secure bitstreams(authenticated or
encrypted or both). As of now, this feature is added and tested only
for xilinx bitstreams and the secure bitstream was generated using
xilinx bootgen tool, but the command is defined in more generic way.
Command example to load authenticated and device key
encrypted bitstream is as follows
"fpga loads 0 100000 2000000 0 1"
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the arguments parsing code by parsing
based on requested operation for fpga loadfs and then
parses the most common/basic args for other fpga load
commands. This makes it easy for new command extensions
or additions especially the commands with more args.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Import the R8A77990 and Ebisu DTS from linux-next to get the latest
version. This makes AVB ethernet work in U-Boot since the ethernet
node is now present in DT, as well as GPIOs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds basic support for the Renesas R-Car E3 (R8A77990) SoC:
- PSCI
- CPU (single)
- Cache controller
- Main clocks and controller
- Interrupt controller
- Timer
- PMU
- Reset controller
- Product register
- System controller
- UART for console
Inspried by a patch by Takeshi Kihara in the BSP.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This follows the style of existion PORT_GP_X macros and
will be used by a follow-up patch for the r8a77990 SoC.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PE clock have two parents, add support for picking the correct
one and deriving the clock from it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PLL rate could be in the GHz range, which could overflow a 32bit
data type. Since the hardware is 64bit anyway, pass the clock rates
as 64bit number internally to avoid this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mul and div arguments were reported in reverse order in the debug
message, swap them to fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Here we do a couple of minor fixes like:
- Move .ivt section to the very beginning of the image
by default which allows us to use that image put right
at reset vector (usually 0x0)
- Improve relocation fix-up which became required once
we moved .ivt and understood a problem with existing implementation
where we relied on a particular placement of sections.
Now we don't care about placement because we just explicitly
check for .text and in case of ARCompact .ivt sections
- Re-implemnt do_reset() such that it calls reset_cpu() which
could implmented for a particular board
And hte most important part we introduce support for yet another
devboard from Synopsys - EMDK.
Synopsys DesignWare ARC EM Development Kit (ARC EMDK) is
an FPGA-based development platform from Synopsys aimed to speed-up
development of software for ARC EM cores and entire subsystems based on
ARC EM like Data Fusion, Secure and Sensor & Control subsystems.
U-Boot is supposed to be used as a primary bootloader on EMDK allowing
users to easily load and start their application from micro-SD card.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This will allow for board-specific implementation of reset.
Default version will just stop execution with help of BRK instruction.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
For quite some time we have a GCC's built-in which inserts BRK
instruction so let's use it instead of simple insertion of in-line
assembly.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is useful for cases when U-Boot image is put in ROM and
reset vector points to 0 where the very beginnign of the image reside.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to have the one and only linker script for all ARC boards
and so we relied on a particular order of symbols there.
Because of that we used __ivt_end as the marker of the end of all the
code which won't be true any longer if we move .ivt section to any other
place. That said we'd better check for each section separately.
A couple of other improvements:
1. There's no point to include the marker of section end in interested
range because its address is beyond the section, i.e. we should
compare with "<" but not "<=".
2. .ivt section for ARCv2 cores is just an array of 32-bit ints and
they are not swapped even on little-endia cores while in case of
ARCompact cores .ivt contains valid code so swapping is required.
3. Just in case add check for ARC600 which is also ARCompact
and its .ivt is normal code.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't care much about I$ line length really as there're
no per-line ops on I$ instead we only do full invalidation of it
on occasion of relocation and right before jumping to the OS.
Also as compared to Linux kernel where we don't support different
lengths of I$ and D$ lines in U-Boot we have to deal with such an
exotic configs if the target board is not supposed to run Linux kernel.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of today 'board/synopsys/' folder contains only Synopsys ARC
boards supported by the same people who support 'arch/arc'.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
While the tests in this testcase are for the log subsystem they are only
able to be run if CONFIG_CMD_LOG is enabled as well as CONFIG_LOG, so
update the buildconfigspec requirement.
Signed-off-by: Tom Rini <trini@konsulko.com>
The /LOG directory was created by the old MAKEALL tool, which was
deleted by commit c8a3777c51 ("Drop the MAKEALL tool").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Provide a logo showing a submarine.
U-Boot currently lacks an icon identifying the project.
The German word U-Boot translates to submarine.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After importing v4.17-rc1 Linux commit 9130ba884640 ("scripts/dtc:
Update to upstream version v1.4.6-9-gaadd0b65c987"), sandbox build
reports below warnings:
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
arch/sandbox/dts/test.dtb: Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Silent them by applying the 's/_/-/' substitution in the names of the
'fdt_dummy0', 'fdt_dummy1', 'fdt_dummy2', 'fdt_dummy3' properties.
Similar DTC warnings have been recently fixed in Linux kernel, e.g. via
v4.17-rc1 commit d366c30d19f4 ("ARM: dts: STi: Fix aliases property name
for STi boards").
If done alone, the DTS update generates a failure of the
`ut dm fdt_translation` unit test in sandbox environment as seen below:
$ ./u-boot -d arch/sandbox/dts/test.dtb
---<-snip->---
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
test/dm/test-fdt.c:444, dm_test_fdt_translation(): 0 == uclass_find_device_by_seq(UCLASS_TEST_DUMMY, 0, 1, &dev): Expected 0, got -19
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
test/dm/test-fdt.c:444, dm_test_fdt_translation(): 0 == uclass_find_device_by_seq(UCLASS_TEST_DUMMY, 0, 1, &dev): Expected 0, got -19
Failures: 2
---<-snip->---
Fix this issue in place, by updating the "name" string in the
UCLASS_DRIVER(fdt_dummy) definition, so that it matches the newly
updated aliases properties. After that, the test passes:
$ ./u-boot -d arch/sandbox/dts/test.dtb
---<-snip->---
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
---<-snip->---
Fixes: e8d5291824 ("core: ofnode: Fix translation for #size-cells == 0")
Reported-by: Petr Vorel <pvorel@suse.cz>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To achieve a DTC state (more or less) equivalent to Linux 4.17-rc4,
backport the DTC-specific part from below Linux commits:
b23d1a241f4eb4 ("kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically")
9a8dfb394c0467 ("kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile")
59889300274569 (".gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore")
e039139be8c251 ("scripts/dtc: generate lexer and parser during build instead of shipping")
b24413180f5600 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
With this commit, the diff between Linux and U-boot common DTC files is:
$ git diff --stat --diff-filter=M v4.17-rc4 <this-commit> -- scripts/dtc
scripts/dtc/.gitignore | 2 +-
scripts/dtc/Makefile | 3 +++
The delta is coming from U-boot commits:
* v2017.11 de163ecedb ("scripts: dtc: Add .gitignore")
* v2018.01 15b97f5c5e ("pylibfdt: move pylibfdt to scripts/dtc/pylibfdt and refactor makefile")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds the following commits from upstream:
aadd0b65c987 checks: centralize printing of property names in failure messages
88960e398907 checks: centralize printing of node path in check_msg
f1879e1a50eb Add limited read-only support for older (V2 and V3) device tree to libfdt.
37dea76e9700 srcpos: drop special handling of tab
65893da4aee0 libfdt: overlay: Add missing license
962a45ca034d Avoid installing pylibfdt when dependencies are missing
cd6ea1b2bea6 Makefile: Split INSTALL out into INSTALL_{PROGRAM,LIB,DATA,SCRIPT}
51b3a16338df Makefile.tests: Add LIBDL make(1) variable for portability sake
333d533a8f4d Attempt to auto-detect stat(1) being used if not given proper invocation
e54388015af1 dtc: Bump version to v1.4.6
a1fe86f380cb fdtoverlay: Switch from using alloca to malloc
c8d5472de3ff tests: Improve compatibility with other platforms
c81d389a10cc checks: add chosen node checks
e671852042a7 checks: add aliases node checks
d0c44ebe3f42 checks: check for #{size,address}-cells without child nodes
18a3d84bb802 checks: add string list check for *-names properties
8fe94fd6f19f checks: add string list check
6c5730819604 checks: add a string check for 'label' property
a384191eba09 checks: fix sound-dai phandle with arg property check
b260c4f610c0 Fix ambiguous grammar for devicetree rule
fe667e382bac tests: Add some basic tests for the pci_bridge checks
7975f6422260 Fix widespread incorrect use of strneq(), replace with new strprefixeq()
fca296445eab Add strstarts() helper function
cc392f089007 tests: Check non-matching cases for fdt_node_check_compatible()
bba26a5291c8 livetree: avoid assertion of orphan phandles with overlays
c8f8194d76cc implement strnlen for systems that need it
c8b38f65fdec libfdt: Remove leading underscores from identifiers
3b62fdaebfe5 Remove leading underscores from identifiers
2d45d1c5c65e Replace FDT_VERSION() with stringify()
2e6fe5a107b5 Fix some errors in comments
b0ae9e4b0ceb tests: Correct warning in sw_tree1.c
Commit c8b38f65fdec upstream ("libfdt: Remove leading underscores from
identifiers") changed the multiple inclusion define protection, so the
kernel's libfdt_env.h needs the corresponding update.
Signed-off-by: Rob Herring <robh@kernel.org>
[ Linux commit: 9130ba884640328bb78aaa4840e5ddf06ccafb1c ]
[erosca: - Fixup conflicts in include/linux/libfdt_env.h caused by v2018.03-rc4
commit b08c8c4870 ("libfdt: move headers to <linux/libfdt.h>
and <linux/libfdt_env.h>")
- Fix build errors in lib/libfdt/fdt_ro.c, tools/libfdt/fdt_rw.c by:
- s/_fdt_mem_rsv/fdt_mem_rsv_/
- s/_fdt_offset_ptr/fdt_offset_ptr_/
- s/_fdt_check_node_offset/fdt_check_node_offset_/
- s/_fdt_check_prop_offset/fdt_check_prop_offset_/
- s/_fdt_find_add_string/fdt_find_add_string_/]
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Pickup the fix for handling unresolved phandles in overlays.
This adds the following commits from upstream:
c1e55a5513e9 checks: fix handling of unresolved phandles for dts plugins
f8872e29ce06 tests: Avoid 64-bit arithmetic in assembler
48c91c08bcfa libfdt: add stringlist functions to linker script
Signed-off-by: Rob Herring <robh@kernel.org>
[ Linux commit: e45fe7f788dd1395befe5639149ad8dacfbd94ab ]
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
After importing linux v4.16-rc1 commit 2c37e08464a8 ("kconfig: Warn if
choice default is not in choice"), Kconfig complains:
scripts/kconfig/conf --syncconfig Kconfig
board/eets/pdu001/Kconfig:22:warning: \
choice default symbol 'PDU001_RUN_LED_RED' \
is not contained in the choice
This looks to be caused by a typo. Fix it.
Fixes: 85ab0452fe ("arm: add support for PDU001")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
Align Kconfig to Linux 4.17-rc4 with minimal impact on non-kconfig files.
Previous Kconfig sync was done by commit bf7ab1e70f ("kconfig:
re-sync with Linux 4.10") and it achieved almost perfect alignment with
a few (intended) exceptions, caused by below U-boot commits:
[A] v2015.04 5f9eb22075 ("kbuild: remove scripts/multiconfig.sh")
[B] v2015.07 20c20826ef ("Kconfig: Enable usage of escape char '\' in string values")
[C] v2016.01 da58dec866 ("Various Makefiles: Add SPDX-License-Identifier tags")
[D] v2016.03 5b8031ccb4 ("Add more SPDX-License-Identifier tags")
[E] v2016.03 192bc6948b ("Fix GCC format-security errors and convert sprintfs.")
Here is the list of Kconfig commits which followed the v4.10 alignment:
[F] v2018.01 0931ed3c0d ("kconfig/symbol.c: use correct pointer type argument for sizeof")
[G] v2018.03 1414e09b4f ("kconfig: revert change that was not needed for -Wformat-security")
[H] v2018.05 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Commit [F] was subsequently applied to Linux kernel as commit [I]
with the same patch id, so it won't contribute to further misalignment.
[I] v4.15-rc1 88127dae6ed9 ("kconfig/symbol.c: use correct pointer type argument for sizeof")
Commit [G] is a Kconfig-specific revert of commit [E].
Commit [H] relocated and reformatted the license doing no functional change.
In summary, the only functional change that makes U-boot Kconfig
diverge from Linux Kconfig is commit [B]. After a brief analysis,
the purpose of [B] seems to be placing "\n" literals in string symbols
like CONFIG_AUTOBOOT_PROMPT="autoboot in %d seconds\n" in order to pass
them directly to printf and expect correct output at runtime. Currently,
Linux doesn't seem to have this requirement, so for the moment [B] looks
like a U-boot specific feature/fix. From point of view of further Kconfig
alignment and backporting efforts, it is highly desired that commits
like [B] are propagated to Linux and any Kconfig fixes/features are
contributed to Linux kernel first. This specific Kconfig re-sync just
keeps [B] in place.
Contrary to 4.10 Kconfig re-sync (which achieves zero non-kconfig
changes), 4.17-rc4 re-sync does some amount of updates in Kbuild
(striving to keep them at minimum), due to a number of reasons:
* Kbuild is affected by the removal of Kconfig "*shipped" files and now
requires flex and bison pre-installed on the host.
* PYTHON{2,3} variables are defined in top-level Makefile as
prerequisite for running the newly developed Kconfig unit tests.
* silentoldconfig becomes an "internal implementation detail" deprecated
for external use, being renamed to syncconfig.
The exact non-kconfig files touched by this commit are:
$ git show --format="" --stat -- ':!scripts/kconfig'
.gitignore | 2 ++
Makefile | 9 +++++++--
scripts/Makefile.build | 11 +++++++++++
scripts/Makefile.lib | 41 ++++++++++++-----------------------------
The imported Linux commits touching the above files are:
c054be10ffdbd5 ("remove gperf left-overs from build system")
73a4f6dbe70a1b ("kbuild: add LEX and YACC variables")
033dba2ec06c47 ("kbuild: prepare to remove C files pre-generated by flex and bison")
eea199b445f64c ("kbuild: remove unnecessary LEX_PREFIX and YACC_PREFIX")
e71de5ee08dcb0 ("kbuild: remove remaining use of undefined YACC_PREFIX")
d59fbbd09d5d6b ("kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)")
911a91c39cabcb H ("kconfig: rename silentoldconfig to syncconfig")
59889300274569 (".gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore")
9a8dfb394c0467 ("kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile")
833e622459432e H ("genksyms: generate lexer and parser during build instead of shipping")
b23d1a241f4eb4 H ("kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically")
e9781b52d4e0e3 H ("kbuild: add PYTHON2 and PYTHON3 variables")
The commits marked with 'H' are assessed as "hard" (build will fail)
prerequisites and the rest of them are assessed as "soft" prerequisites
for the re-sync. In spite of relatively high number of non-H commits,
they belong to this Kconfig update topic-wise and decrease the number of
cherry pick conflicts for many commits in this series. Additional effort
can be put in eliminating the soft prerequisites, if really needed.
The commits which contributed to this Kconfig re-sync are listed below.
Whenever a conflict resolution has been performed (mostly by hand, but
sometimes automatically by git), it is revealed by the '!' sign in the
second column, which means a patch id mismatch between Linux and U-boot
commits:
9be3213b14d44f ("gconfig: remove misleading parentheses around a condition")
ff85a1a80e0034 ("kconfig: Check for libncurses before menuconfig")
ad8181060788c8 ("kconfig: fix sparse warnings in nconfig")
cb77f0d623ff33 ! ("scripts: Switch to more portable Perl shebang")
bb3290d91695bb ! ("Remove gperf usage from toolchain")
c054be10ffdbd5 ("remove gperf left-overs from build system")
b24413180f5600 ! ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license")
9059a3493efea6 ! ("kconfig: fix relational operators for bool and tristate symbols")
2c37e08464a850 ("kconfig: Warn if choice default is not in choice")
33ca1a24866373 ("kconfig: Document the 'menu' struct")
52aede4ba5efd1 ("kconfig: Document the 'symbol' struct")
c873443430ebd1 ("kconfig: Sync zconf.y with zconf.tab.c_shipped")
9a826842ff2fbd ("kconfig: Rename menu_check_dep() to rewrite_m()")
fa8cedaef814ce ("kconfig: Clarify expression rewriting")
f77850d3fe0c96 ("kconfig: Clean up modules handling and fix crash")
e3b03bf29d6b99 ("kconfig: display recursive dependency resolution hint just once")
73a4f6dbe70a1b ! ("kbuild: add LEX and YACC variables")
033dba2ec06c47 ! ("kbuild: prepare to remove C files pre-generated by flex and bison")
29c833061c1d8c ("kconfig: generate lexer and parser during build instead of shipping")
26e47a3c11a25c ("kconfig: Don't leak symbol names during parsing")
24161a6711c945 ("kconfig: Don't leak 'source' filenames during parsing")
bc28fe1d5ede88 ("kconfig: Don't leak 'option' arguments during parsing")
0724a7c32a54e3 ("kconfig: Don't leak main menus during parsing")
ae7440ef0c8013 ("kconfig: Fix automatic menu creation mem leak")
5b1374b3b3c2fc ("kconfig: Fix expr_free() E_NOT leak")
7cf33f88e29410 ("kconfig: Fix choice symbol expression leak")
05cccce580456d ("kconfig: Document automatic submenu creation code")
0735f7e5def2ab ("kconfig: Document important expression functions")
df60f4b92d3d0b ("kconfig: Remove menu_end_entry()")
b92d804a51796b ("kconfig: drop 'boolean' keyword")
6479f327dea60d ("kconfig: Warn if there is more than one help text")
52e58a3caeba5d ("kconfig: make input_mode static")
5a3dc717b3c785 ("kconfig: make xfgets() really static")
84dd95d4f87a0d ("kconfig: make conf_unsaved a local variable of conf_read()")
765f4cdef6f80d ("kconfig: use default 'yy' prefix for lexer and parser")
eea199b445f64c ("kbuild: remove unnecessary LEX_PREFIX and YACC_PREFIX")
e71de5ee08dcb0 ("kbuild: remove remaining use of undefined YACC_PREFIX")
d59fbbd09d5d6b ! ("kbuild: replace hardcoded bison in cmd_bison_h with $(YACC)")
3e41ba05b6d60c ("kconfig: Document SYMBOL_OPTIONAL logic")
d3465af60f4471 ("kconfig: Clarify choice dependency propagation")
9d1a9e8bc18bea ("kconfig: Document 'if' flattening logic")
b53688014e3325 ("kconfig: Clarify menu and 'if' dependency propagation")
d0fd0428ecf04b ("kconfig: fix make xconfig when gettext is missing")
312ee68752faaa ("kconfig: announce removal of oldnoconfig if used")
1ccb27143360bd ("kconfig: make "Selected by:" and "Implied by:" readable")
cedd55d49dee94 ! ("kconfig: Remove silentoldconfig from help and docs; fix kconfig/conf's help")
1b9eda2e4892cb ("kconfig: Warn if help text is blank")
cb67ab2cd2b8ab ("kconfig: do not write choice values when their dependency becomes n")
4f208f392103e8 ("kconfig: show '?' prompt even if no help text is available")
cd58a91def2acc ("kconfig: remove 'config*' pattern from .gitignnore")
d2a04648a5dbc3 ("kconfig: remove check_stdin()")
f3ff6fb5db68bc ("kconfig: echo stdin to stdout if either is redirected")
9e3e10c725360b ("kconfig: send error messages to stderr")
d717f24d8c6808 ("kconfig: add xrealloc() helper")
523ca58b7db2e3 ("kconfig: remove const qualifier from sym_expand_string_value()")
cd81fc82b93fa4 ("kconfig: add xstrdup() helper")
f4bc1eefc1608e ("kconfig: set SYMBOL_AUTO to the symbol marked with defconfig_list")
bf0bbdcf100322 ("kconfig: Don't leak choice names during parsing")
1a90ce36c6eff6 ("kconfig: Update ncurses package names for menuconfig")
5ae6fcc4bb82bd ("kconfig: fix line number in recursive inclusion error message")
07a422bb213adb ! ("kbuild: restore autoksyms.h touch to the top Makefile")
9a47ceec543bfb ("kconfig: clean-up reverse dependency help implementation")
d9119b5925a03b ("kconfig: Print reverse dependencies in groups")
f467c5640c29ad ("kconfig: only write '# CONFIG_FOO is not set' for visible symbols")
59a80b5e892dde ("kconfig: do not call check_conf() for olddefconfig")
4bb3a5b085cd6f ("kconfig: remove unneeded input_mode test in conf()")
99f0b6578bab44 ("kconfig: remove redundant input_mode test for check_conf() loop")
2aad9b89621386 ("kconfig: hide irrelevant sub-menus for oldconfig")
81d2bc2273052e ("kconfig: invoke oldconfig instead of silentoldconfig from local*config")
911a91c39cabcb ! ("kconfig: rename silentoldconfig to syncconfig")
2a61625835c7c8 ! ("kconfig: remove redundant streamline_config.pl prerequisite")
022a4bf6b59dfd ("kconfig: tests: add framework for Kconfig unit testing")
1903c511905984 ("kconfig: tests: add basic choice tests")
49ac3c0c3aa3b7 ("kconfig: tests: test automatic submenu creation")
b76960c0f6b25d ("kconfig: tests: test if new symbols in choice are asked")
930c429a656fdb ("kconfig: tests: check unneeded "is not set" with unmet dependency")
ee236610653ede ("kconfig: tests: check visibility of tristate choice values in y choice")
beaaddb625400e ("kconfig: tests: test defconfig when two choices interact")
3e4888c2e3d77d ("kconfig: tests: test randconfig for choice in choice")
29c434f367ea7b ("kconfig: tests: test if recursive dependencies are detected")
e2c75e7667c737 ("kconfig: tests: test if recursive inclusion is detected")
f622f827958162 ("kconfig: warn unmet direct dependency of tristate symbols selected by y")
f8f69dc0b4e070 ("kconfig: make unmet dependency warnings readable")
26561514cc9def ("kconfig: do not include both curses.h and ncurses.h for nconfig")
32a94b8b0c3e5a ("kconfig: remove duplicated file name and lineno of recursive inclusion")
379a8eb8eb1a55 ("kconfig: detect recursive inclusion earlier")
18492685e479fd ("kconfig: use yylineno option instead of manual lineno increments")
59889300274569 ! (".gitignore: move *.lex.c *.tab.[ch] patterns to the top-level .gitignore")
9a8dfb394c0467 ! ("kbuild: clean up *.lex.c and *.tab.[ch] patterns from top-level Makefile")
833e622459432e ! ("genksyms: generate lexer and parser during build instead of shipping")
b23d1a241f4eb4 ! ("kbuild: add %.lex.c and %.tab.[ch] to 'targets' automatically")
17baab68d337a0 ("kconfig: extend output of 'listnewconfig'")
e9781b52d4e0e3 ! ("kbuild: add PYTHON2 and PYTHON3 variables")
The current Kconfig update generates below build-time warnings:
YACC scripts/dtc/dtc-parser.tab.h
scripts/dtc/dtc-parser.y: warning: 3 shift/reduce conflicts [-Wconflicts-sr]
YACC scripts/dtc/dtc-parser.tab.c
scripts/dtc/dtc-parser.y: warning: 3 shift/reduce conflicts [-Wconflicts-sr]
This seems to happen because the Kbuild updates apparently didn't make
room for both "*shipped"-based builds and flex/bison-based builds. A
similar problem has been reported for genksyms parser in v4.17-rc1
commit 833e622459432e ("genksyms: generate lexer and parser during build
instead of shipping"). I have figured out empirically that the warnings
are healed after updating the in-tree U-boot DTC to upstream v1.4.6-9,
same as done by Linux v4.17-rc1 commit 9130ba88464032 ("scripts/dtc:
Update to upstream version v1.4.6-9-gaadd0b65c987"). Whether fixing the
DTC-related yacc warnings should be done together with the Kconfig
re-sync, I would like to hear from community.
My testing was limited to:
- make defconfig all
- make ARCH=arm CROSS_COMPILE=aarch64-linux-gnu- r8a7795_ulcb_defconfig all
- comparing .config before and after the re-sync
- running the newly imported Kconfig unit tests as seen below:
$ make testconfig
Tested-by: Petr Vorel <petr.vorel@gmail.com>
============================= test session starts =============================
scripts/kconfig/tests/auto_submenu/__init__.py::test PASSED [ 7%]
scripts/kconfig/tests/choice/__init__.py::test_oldask0 PASSED [ 14%]
scripts/kconfig/tests/choice/__init__.py::test_oldask1 PASSED [ 21%]
scripts/kconfig/tests/choice/__init__.py::test_allyes PASSED [ 28%]
scripts/kconfig/tests/choice/__init__.py::test_allmod PASSED [ 35%]
scripts/kconfig/tests/choice/__init__.py::test_allno PASSED [ 42%]
scripts/kconfig/tests/choice/__init__.py::test_alldef PASSED [ 50%]
scripts/kconfig/tests/choice_value_with_m_dep/__init__.py::test PASSED [ 57%]
scripts/kconfig/tests/err_recursive_inc/__init__.py::test PASSED [ 64%]
scripts/kconfig/tests/inter_choice/__init__.py::test PASSED [ 71%]
scripts/kconfig/tests/new_choice_with_dep/__init__.py::test PASSED [ 78%]
scripts/kconfig/tests/no_write_if_dep_unmet/__init__.py::test PASSED [ 85%]
scripts/kconfig/tests/rand_nested_choice/__init__.py::test PASSED [ 92%]
scripts/kconfig/tests/warn_recursive_dep/__init__.py::test PASSED [100%]
========================== 14 passed in 0.34 seconds ==========================
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Petr Vorel <petr.vorel@gmail.com>
This patch adds HS200 suuport for ZynqMP and enables
the same for ZC1751 DC1 board which has eMMC on it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PS clock(LPD_APB_CLK) is default clock for TTC. Add this clock
entry in TTC nodes.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Card detect bit was broken on revA and it is working fine with revC
board that's why this property can be removed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is control board on Bitmain Antminer S9.
There are 3 board variables with 256MB, 512MB and 1024MB DDR.
DDR memory is automatically detected with using get_with using
get_ram_size().
Bitmain is using 16MB space for FPGA which is handled via
reserved-memory. Also U-Boot is allocating 16B for storing bootcounts.
Watchdog is started but never service in U-Boot.
SPL MMC is working. SPL NAND is not working because it is not supported
as of now.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Detect mmc alias at run time for setting up proper boot_targets sequence.
The first target has to correspond with boot mode.
The purpose of this patch is to get rid of CONFIG_ZYNQ_SDHCI0/1
parameters in full U-Boot.
Unfortunately this patch can't remove it because there is missing
mmc implementation for SPL_DM_SEQ_ALIAS.
Also xilinx_zynqmp.h only setup boot commands for mmc0 and mmc1.
It means using aliases with higher number won't work. But switching
between mmc0 and mmc1 should work properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Existing EEMI version is to as 1.0 (available from xilinx v2018.1
version). Update required API version to match with EEMI API version.
New PMUFW version is required for operations with programmable logic.
Signed-off-by: Rajan Vaja <rajanv@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ZynqMP emulation platforms are no longer tested and supported that's why
remove macros and code around.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Read reset reason reg and show it in log and also save it as variable.
Clearing reset reason when it is read to show only one status
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to specify header with full soc name.
Symlink is setup automatically (arch -> arch-zynqmp)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Convert USB fastboot code to use shared fastboot protocol.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce 'oem format' which matches the USB implementation, guard this
with CONFIG_FASTBOOT_CMD_OEM_FORMAT so that you can configure it out.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce CONFIG_IMAGE_SPARSE and CONFIG_CMD_MMC_SWRITE so the "mmc
swrite" command is separated from the fastboot code.
Move image-sparse from common to lib so it's clear it's library code.
Rename CONFIG_FASTBOOT_FLASH_FILLBUF_SIZE to CONFIG_IMAGE_SPARSE_FILLBUF_SIZE
and migrate it to Kconfig.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add FASTBOOT_FLASH_NAND_TRIMFFS to Kconfig; note there are no in-tree
users of it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Overriding fastboot_set_reboot_flag() in arch/arm/mach-omap2/boot-common.c
leaves it applying all boards that derive from this, not just the ones which
have support for Android bootloader flow. Move the weak function override to
the relevant board files.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename fb_mmc_flash_write/fb_mmc_erase/fb_nand_flash_write/fb_nand_erase to
fastboot_... as they form a public interface
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move FASTBOOT_VERSION to include/fastboot.h so when we merge the UDP code
we only have one definition.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Rename fb_set_reboot_flag to fastboot_set_reboot_flag so it matches
all other fastboot code in the global name space. Fix the guards around
them so that they're dependent on FASTBOOT, not just USB_FUNCTION_FASTBOOT.
Move the weak implementation of fastboot_set_reboot_flag to fb_common.c
so we can call it from non-USB fastboot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Compiling on a 64 bit target the arguments to _fb_nand_write are
incompatible:
drivers/fastboot/fb_nand.c: In function ‘_fb_nand_write’:
drivers/fastboot/fb_nand.c:101:42: warning: passing argument 3 of ‘nand_write_skip_bad’ from incompatible pointer type [-Wincompatible-pointer-types]
return nand_write_skip_bad(mtd, offset, &length, written,
^
In file included from drivers/fastboot/fb_nand.c:16:0:
include/nand.h:107:5: note: expected ‘size_t * {aka long unsigned int *}’ but argument is of type ‘unsigned int *’
int nand_write_skip_bad(struct mtd_info *mtd, loff_t offset, size_t *length,
^~~~~~~~~~~~~~~~~~~
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CONFIG_FASTBOOT_GPT_NAME and CONFIG_FASTBOOT_MBR_NAME are always defined
by Kconfig if you're compiling this code, so remove these redundant
defaults.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ensure that when selecting FASTBOOT_FLASH you end up with a buildable
configuration. Prior to this you could select NAND without MTDPARTS
and end up with an image which (surprisingly) excluded NAND.
Also fix dependencies on FASTBOOT_GPT_NAME/FASTBOOT_MBR_NAME which require
you have EFI_PARTITION/DOS_PARTITION enabled.
Delete redundant FASTBOOT_FLASH_NAND_DEV from Kconfig - it was only ever
used as a guard and the value was ignored in all cases, we're using
FASTBOOT_FLASH_NAND as the guard now.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add drivers/fastboot/fb_common.c, where fastboot_okay/fail are implemented
so we can call them from a non-USB implementation.
Introduce fastboot_response which takes varargs parameters so we can
use it to generate formatted response strings. Refactor fastboot_okay/fail
to use it.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Add the response string as a parameter to fastboot_okay/fail, instead
of modifying a global, to match the contract expected by the AOSP
U-Boot code.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Separate CMD_FASTBOOT from FASTBOOT and move code and configuration to
drivers/fastboot.
Switch dependencies on FASTBOOT to USB_FUNCTION_FASTBOOT as anyone who wants
FASTBOOT before this series wants USB_FUNCTION_FASTBOOT. Split
USB_FUNCTION_FASTBOOT from FASTBOOT so they retain their existing
behaviour.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There are memory leaks of usb request and its buffer for ep0,
in_ep, and out ep. Fix memory leaks of usb request and its buffer.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The xhci wrapper-driver for Rockchip searches the DTS to find its
child node compatbile with 'rockchip,rk3399-usb3-phy' to retrieve the
base-address of the PHY. However, this is currently broken (and
always has been), returning NULL. However, the (wrongly) retrieved
base-address is never used.
We thus remove this code for now.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In xhci_set_configuration(), 'Context Entries' field in the slot
context was cleared with mask LAST_CTX_MASK, but it should have
taken the endianness into consideration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a full speed hub connects to a high speed hub which supports MTT,
the MTT field of its slot context will be set to 1 when xHCI driver
setups an xHCI virtual device in xhci_setup_addressable_virt_dev().
Once usb core fetch its hub descriptor, and need to update the xHC's
internal data structures for the device, the HUB field of its slot
context will be set to 1 too, meanwhile MTT is also set before, this
will cause configure endpoint command fail. In the case, we should
clear MTT to 0 for full speed hub according to section 6.2.2.
This keeps in sync with Linux kernel commit:
096b110: usb: xhci: fix config fail of FS hub behind a HS hub with MTT
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Per xHCI spec chapter 6.2.2 table 6-7, as input, software shall
initialize the dev_state field to '0'. Though this does not seem
to cause any issue with most xHC implementations, let's do this
to conform with the spec.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
If a USB 3.0 hub is plugged into the root port of the xHC, the xHCI
driver will issue a 'Configure Endpoint' command to the xHC for it
to update its internal data structure for this hub device. The hub
attributes are in the slot context so we need tell xHC to update the
slot context by setting the add context flags of the input control
context to only cover the slot context.
At present the add context flags is or'ed with the slot context bit,
but it should really be accurately set to the slot context, as the
variable that holds the value of the add context flags comes from
whatever was set in the last command execution, which may contain
additional contexts that 'Configure Endpoint' command should not
touch. Some xHC implementations like x86 don't complain such, but
it was observed on Renesas RCar Gen3 platform that the RCar xHC
complains with a 'TRB error' completion codes as the response.
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
During the execution of xhci_deregister xHCI registers are accessed. If
the clock is already deactivated when xhci_deregister is called this can
lead to undefined behavior. Change the order to deregister the device
before deactivating the clock.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Fix riscv: ax25-ae350 build fail problem
https://travis-ci.org/trini/u-boot/jobs/385147373
...
Building current source for 1 boards (1 thread, 2 jobs per thread)
riscv: + ax25-ae350
+arch/riscv/cpu/ax25/start.S: Assembler messages:
+arch/riscv/cpu/ax25/start.S:48: Error: unrecognized opcode `sd a2,0(t0)'
+arch/riscv/cpu/ax25/start.S:112: Error: unrecognized opcode `ld t5,0(t0)'
...
After apply the commit
configs: ax25-ae350: Set 64-bit as default configuration
Toolchain shall be also setuped with 64-bit in .travis.yml.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Chih-Mao Chen <cmchen@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
The missing clock causes serial_msm driver probe to fail.
Added a dummy node so the probe succeeds, as the clock init
currently in db820c is empty.
Fixes: 11d59fe537 ("serial: serial_msm: fail probe if settings clocks fails")
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Android documentation defines the recommended image format for storing
DTB/DTBO files in a single dtbo.img image. This patch includes the
latest header file with the struct definitions for this format from
AOSP.
The header was adapted to U-Boot's coding style and the function
declarations were removed.
Signed-off-by: Alex Deymo <deymo@google.com>
[trini: Change SDPX tag location]
Signed-off-by: Tom Rini <trini@konsulko.com>
This was being used by some Marvell boards to enable some file system
related features (many of which have already been moved to Kconfig).
Make the future migration of the final 2 or 3 config options easier by
expanding #define CONFIG_SYS_MVFS into the options that it enables and
remove CONFIG_SYS_MVFS.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add smc_init() to get register base from dts and
deal with atfsmc020 controler initialzation job.
Write protect is enabled by default. So WP shall
be disabled when startup, then cfi flash can be
detected and erasing and writing can be executed.
Adp-ae3xx and adp-ag101p both do smc initilize job
in lowlevel_init.S and get register base fron
CONFIG_FTSMC020_BASE. They also can be moved those
codes to board stage. Remind them as todo jobs.
After that CONFIG_FTSMC020_BASE can be removed.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Enable cfi flash driver and setup flash
parameters to support parallel nor flash
which type is JS28F00A-M29EWH.
Verification:
Size detection, data read, erase and write are all ok.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
The compatible string of ftsdc010_mci.c is different from
the mmc driver in Linux Kernel. Modify it for consistency.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Fix warnings as below when compile in 64-bit.
warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Fix warning as below when compile in 64-bit.
warning: format '%u' expects argument of type
'unsigned int', but argument 6 has type 'size_t
{aka long unsigned int}
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Andes has rearranged the product combinations.
nx25 and ax25 both are RISC-V architecture cpu core.
But ax25 has MMU unit inside, and nx25 is not.
Cpu nx25 and platform ae250 are arranged in pairs.
Cpu ax25 and platform ae350 are arranged in pairs.
This patch will rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Then u-boot can boot linux kernel in ae350
platform reasonably.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
We have almost all pieces needed to support RISC-V UEFI binaries in place already.
The only missing piece are ELF relocations for runtime code and
data.
This patch adds respective support in the linker script and the runtime
relocation code. It also allows users to enable the EFI_LOADER configuration
switch on RISC-V platforms.
Signed-off-by: Alexander Graf <agraf@suse.de>
Distro boot allows for a common boot path on systems that allow distributions
to easily boot from a default configuration.
This patch enables distro boot for the nx25-ae250. Hopefully this can serve
as a good example for new boards, so they enable it as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
While we don't have UEFI naming conventions for RISC-V file paths yet,
we need to search for something. So let's copy the removable file paths
from the RISC-V edk2 port.
Also add the official VCI strings that contain the standardized RISC-V
architecture ID fields.
Signed-off-by: Alexander Graf <agraf@suse.de>
We were using our EFI_CACHELINE_SIZE define only in the runtime service
code, but left the image loader to use plain CONFIG_SYS_CACHELINE_SIZE.
This patch moves EFI_CACHELINE_SIZE into efi_loader.h and converts
the image loader to use it.
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch adds an empty stub for board_quiesce_devices() which allows boards
to quiesce their devices before we boot into an OS in a platform agnostic way.
Signed-off-by: Alexander Graf <agraf@suse.de>
The hello world binary and a few selftests require to build EFI target
binaries, not just the EFI host environment.
This patch adds all required files to generate an EFI binary for
RISC-V.
Signed-off-by: Alexander Graf <agraf@suse.de>
The linker can remove sections that are never addressed, so it makes a lot
of sense to declare every function as an individual section.
This reduces the output U-Boot code size by ~30kb for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
mv-common.h and mv-plug-common.h still had comments delimiting sections
of configuration options that have all been moved to Kconfig by previous
treewide efforts. Remove the redundant comment sections.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The last option guarded by this ifdef was removed in commit 68d5342017
("sf: Move SPI flash drivers to defconfig"). Remove the now empty
ifdef/endif block and the associated comment.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the new ahci mvebu driver for marvell arm64 platform
SOCs(A3k and A8k). And since AHCI_MVEBU selects SCSI_AHCI, so
"CONFIG_SCSI_AHCI=y" is removed from those default config files.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Mvebu AHCI is AHCI driver which uses SCSI under the hood.
This patch adjusts AHCI setup to support SCSI by creating
a SCSI device as a child. Since the functions of creating
SCSI device need the kconfig option DM_SCSI, so let
AHCI_MVEBU select DM_SCSI.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
This workaround was added for A8040/7040 A0.
A8040/7040 A0 is no longer supported so this workaround
can be removed.
Signed-off-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently mvebu sata driver is in arch/arm/mach_mvebu directory, this
patch moves it to drivers/ata directory with renaming "sata.c" to
"ahci_mvebu.c" which is aligned to Linux.
New ahci driver's kconfig option is added as AHCI_MVEBU which selects
SCSI_AHCI and is based on AHCI.
Signed-off-by: Ken Ma <make@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SDHCI interface on AP and CP0 in A80x0 DTS files
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When the pin control driver selects SD/eMMC function for
a pin group, there is additional configuration to be done
for this case - switch the PHY to work with SDHCI interface.
This patch adds the missing functionality into the pin
control driver.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Evan Wang <xswang@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Without this USB3 won't work in U-Boot.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
orangepi-prime has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
orangepi-pc2 has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Bananapi-m2-plus has usb otg routed host with either EHCI0/OHCI0
sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner H3 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so drop existing legacy handling like arch/arm/mach-sunxi.c
and related code areas.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
The sunxi otg phy has a bug where it wrongly detects a high speed squelch
when reset on the root port gets de-asserted with a lo-speed device.
The workaround for this is to disable squelch detect before de-asserting
reset, and re-enabling it after the reset de-assert is done. Add a sunxi
specific phy function to allow the sunxi-musb glue to do this.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Allwinner PHY USB code is now part of generic-phy framework,
so use it in board_usb_cable_connected.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Sync sun4i-usb-phy bindings from Linux, since the
drivers/phy/allwinner/phy-sun4i-usb.c follow similar.
Sync changes from Linux with below commit:
"phy: sun4i-usb: add support for R40 USB PHY"
(sha1: f3d96f8d23d8e6d0b7642ee946b9b2ac3418fb4d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike, other Allwinner SUN4I Phy supporting SOC, A83T has
2 USB PHY's and second one is HSIC. So phy control need to
configure to handle these HSIC and SIDDQ requirement.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
ID and VBUS detection code require when musb changing
between Host and/or Peripheral modes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
USB PHY implementation for Allwinner SOC's can be handling
in to single driver with different phy configs.
This driver handle all Allwinner USB PHY's start from 4I to
50I(except 9I). Currently added A64 compatibility more will
add in next coming patches.
Current implementation is unable to get pinctrl, clock and reset
details from DT since the dm code on these will add it future.
Driver named as phy-sun4i-usb.c since the same PHY logic
work for all Allwinner SOC's start from 4I to A64 except 9I
with different phy configurations.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Like other Allwinner SoC, the H3/H5/A64 is missing the config register
from the musb hardware block. Use a known working value for it
like other SoC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
clock gating bits on a64 are different than H3_H5, so fixed
only required bits on clock_sun6i.h.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Unlike other Allwinner SOC's H3/H5/V3s OTG support 4 endpoints
with relevant fifo configs, rest all have 5 endpoints.
So add the fifo configs and defer them based on driver_data.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Filling musb_hdrc pdata using structure will unnecessary
add extra ifdefs, so fill them inside probe call for
better code understanding and get rid ifdefs using
devicetree compatible.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
- add proper macros for musb_config members
- use bool 'true' for multipoint and dyn_fifo instead of numerical 1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Add FIT data-position & data-offset property support for bootm,
which were already supported in SPL.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Follow implementation in mALLOc(). Check GD_FLG_FULL_MALLOC_INIT flag and use
malloc_simple if GD_FLG_FULL_MALLOC_INIT is unset. Adjust the malloc bytes
to align with the requested alignment.
The original memalign() function will access mchunkptr struct to adjust the
alignment if there is misalignment happen, but mchunkptr struct is not being
initialized before full malloc is initialized. This cause the system crash.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
SDMMC_CMD_CPSMEN bit is wrongly check and set in
SDMMC_ARG register instead of SDMMC_CMD register.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use OTP57 and 58 for MAC address
- OTP57 = MAC address bits [31:0]
- OTP58 = MAC address bit [47:32] stored in OTP LSB's
Use manufacture information in OTP13 to OTP15 to build unique
chip id saved in env variable "serial#"
(used for USB device enumeration)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add a MISC driver with read and write access to BSEC IP
(Boot and Security and OTP control)
- offset 0: shadowed values
- offset 0x80000000: OTP fuse box values (SAFMEM)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The register TAMP_BOOT_CONTEXT is already updated in
get_bootmode() in cpu.c and no need to be done
twice.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the needed information to enable the debug uart
to have printf before the serial driver probe
(so before probe for clock, pincontrol and reset drivers)
To enable the debug on uart 4 (default console):
+ CONFIG_DEBUG_UART=y
+ CONFIG_DEBUG_UART_STM32=y
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Implements serial setparity ops to allow uart parity change.
It allows to select ODD, EVEN or NONE parity.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rename USART_ISR_FLAG_xxx bits to USART_ISR_xxx bits and
USART_ICR_OREF to USART_ICR_ORECF in order to match datasheets.
Sort defines by descendant order.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for early debug printf, before the availability of
driver model and device tree support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Serial port configuration was missing from previous implementation.
It only worked because it was preconfigured by LK.
This patch configures the uart for 115200 8N1.
It also configures the pin mux for uart pins using DT bindings.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
This patch adds pinmux and pinctrl driver for TLMM
subsystem in snapdragon chipsets.
Currently, supporting only 8016, but implementation is
generic and 8096 can be added easily.
Driver is using the generic dt-bindings and doesn't
introduce any new bindings (yet).
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The uart is already initialized prior to relocation,
reinitialization after relocation is unnecessary.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Failure to set the clocks will causes data abort exception when
trying to write to AHB uart registers.
This patch ensures that we don't touch these registers if clock
setting failed.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The clock and serial nodes are needed before relocation.
This patch ensures that the msm-serial driver will probe
and provide uart output before relocation.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that there are more boards defining this it can be removed from the
whitelist.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, if we happen to allocate an address requiring 64 bits to a
device only supporting 32-bit BARs, the address eventually gets silently
truncated to 32 bits. Avoid this by adding a new flag to
pciauto_region_allocate() to bail out in such situations.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
All of the debug output from this file is squished to one line. Fix
it.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that U-Boot works fine with highmem enabled, there is no need to
tell users to disable highmem.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that PCI devices work with highmem-enabled QEMU emulation, bump up
the RAM size in the MMU tables to gain access to the full 255 GB of RAM
potential instead of the puny 3 GB.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently, qemu_arm_defconfig and qemu_arm64_defconfig only work with
the 'highmem=off' parameter passed to QEMU's virt machine. The reason is
that when 'highmem' is not disabled, QEMU appends 64-bit a memory
resource to the PCI controller's regions property in DT in addition to
the 32-bit PCI memory window in low memory. And the current DT parsing
code picks the last (thus the 64-bit one) memory resource, whose address
eventually gets silently truncated to 32 bits because
CONFIG_SYS_PCI_64BIT is not set, which obviously causes PCI to break.
Avoid this problem by ignoring memory regions whose addresses are above
the 32-bit boundary when CONFIG_SYS_PCI_64BIT is not set.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
This node declares the presence of the Sandbox TPMv2.x emulated chip,
available for testing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This driver can emulate all the basic functionalities of a TPMv2.x
chip and should behave like them during regular testing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add tests for the TPMv2.x commands.
These commands may run both on a physical TPM and with the sandbox
driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On some designs, the reset line could not be connected to the SoC reset
line, in this case, request the GPIO and ensure the chip gets reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for the TPM2_PCR_SetAuthPolicy and
TPM2_PCR_SetAuthValue commands.
Change the command file and the help accordingly.
Note: These commands could not be tested because the TPMs available
do not support them, however they could be useful for someone else.
The user is warned by the command help.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_HierarchyChangeAuth command.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_DictionaryAttackParameters and
TPM2_DictionaryAttackLockReset commands.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_GetCapability command.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_PCR_Read command.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_PCR_Extend command.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for the TPM2_Selftest command.
Change the command file and the help accordingly.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of returning a generic 'library' error, report back the actual
error code so it can be displayed to the user by the regular error path.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When debugging, it is welcome to get more information about what the TPM
returns. Add the possibility to print the packets received to show their
exact content.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
TPM commands are much easier to read/write with these macros that will
transform words or integers into byte strings. This way, there is no
need to call pack_byte_string() while all variable length in a command
are known (and at must 4 bytes, which is a lot of them).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Choice between v1 and v2 compliant functions is done with the
configuration.
Create the various files that will receive TPMv2-only code on the same
scheme as for the TPMv1 code.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Both parameters 'duration_ms' and 'retry_time_ms' of the tpm_chip_priv
structure are documented is the comment above the declaration but 'buf'
was forgotten. Add the missing description.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are no changes in this commit but a new organization of the code
as follow.
* cmd/ directory:
> move existing code from cmd/tpm.c in cmd/tpm-common.c
> move specific code in cmd/tpm-v1.c
> create a specific header file with generic definitions for
commands only called cmd/tpm-user-utils.h
* lib/ directory:
> move existing code from lib/tpm.c in lib/tpm-common.c
> move specific code in lib/tpm-v1.c
> create a specific header file with generic definitions for
the library itself called lib/tpm-utils.h
* include/ directory:
> move existing code from include/tpm.h in include/tpm-common.h
> move specific code in include/tpm-v1.h
Code designated as 'common' is compiled if TPM are used. Code designated
as 'specific' is compiled only if the right specification has been
selected.
All files include tpm-common.h.
Files in cmd/ include tpm-user-utils.h.
Files in lib/ include tpm-utils.h.
Depending on the specification, files may include either (not both)
tpm-v1.h or tpm-v2.h.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Fix a few more cases of tpm.h -> tpm-v1.h, some Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Because both major revisions are not compatible at all, let's make them
mutually exclusive in Kconfig. This way we will be sure, when using a
command or a library function that it is supported by the right
revision.
Current drivers are currently prefixed by "tpm_", we will prefix TPMv2.x
files by "tpm2_" to make the distinction without moving everything.
The Kconfig menu about TPM drivers is now divided into two sections, one
for each specification. Compliant drivers with one specification will
only show up if this specification _only_ has been selected, otherwise a
comment is displayed.
Once a driver is selected by the user, it selects automatically a
boolean value, that is needed in order to activate the TPM commands.
Selecting the TPM commands will automatically select the right
command/library files.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework deps as TPM_V1 and TPM_V2 depend on TPM,
drop TPM_DRIVER_SELECTED]
Signed-off-by: Tom Rini <trini@konsulko.com>
TPM are shipped with a few read-only register from which we can retrieve
for instance:
- vendor ID
- product ID
- revision ID
Product and vendor ID share the same register and are already referenced
in the tpm_chip structure. Add the revision ID entry which is missing.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix following checkpatch.pl issue in TPM-related code:
WARNING: Missing a blank line after declarations
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix following checkpatch.pl issues in TPM-related code:
CHECK: '<x>' may be misspelled - perhaps '<y>'?
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix following checkpatch.pl issue in TPM-related code:
CHECK: Alignment should match open parenthesis
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix following checkpatch.pl issues in TPM-related code:
CHECK: Prefer kernel type 'u8' over 'uint8_t'
CHECK: Prefer kernel type 'u16' over 'uint16_t'
CHECK: Prefer kernel type 'u32' over 'uint32_t'
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix following checkpatch.pl issue in TPM-related code:
WARNING: space prohibited between function name and open
parenthesis '('
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 819f1e081c.
This check was introduced in order to cope with the size limitation we had
when we were still using the raw environment in MMC. However, this
introduces padding as well, which can result in an overly huge binary if
one wants to flash the environment to some other location.
Since we now have a FAT-based environment, this check is not so useful
anymore, so we can just drop it.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Måns Rullgård <mans@mansr.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for DEBUG_UART on ARC devboards
This required us to do 2 things:
1) Insert a call to debug_uart_init() in early boot code
2) Convert serial_arc to Kconfig
Once both items above are done we just patched defconfigs.
Patch queue for rpi - 2018-05-24
Some minor fixes for the Raspberry Pi:
- Fix SD writes on new sdhost controller
- Sanitize default load addresses, allowing for better payload placement
The debug UART is intended for use very early in U-Boot to debug
problems before serial drivers are up.
Call debug_uart_init right before board_init_f.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of Linux 4.16, a multiplatform AArch64 kernel with our distro config
takes 26M. The current space reservation leaves only 17M for the kernel
and if it goes over it, the initrd gets overwritten when loading the
kernel from the filesystem.
A similar problem happens on ARMv7 with the DTBs taken from the
downstream Raspberry Pi foundation kernel. I guess they compile them
with DT overlay support enabled which grows them just enough.
Fix both of these problems by rewriting the memory map, which now allows
kernels to be up to 36M and DTBs up to 1M. Also the comment block was
kind of obsolete ever since the introduction of AArch64 support and the
firmware-loaded DTB doesn't get placed at 0x100 anymore either, so that
is fixed as well.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add support for loading U-Boot and optionally FDT from a fitImage
in SPL by using the full fitImage support from U-Boot. While we do
have limited SPL loading support in SPL with a small footprint, it
is missing a lot of important features, like checking signatures.
This support has all the fitImage features, while the footprint is
obviously larger.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The script decodecode can be used to disassemble the 'Code:' line written
when an exception occurs.
The script is copied from Linux v4.16.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If an exception occurs in a loaded image and the relocation offset is
unknown, it is helful to know the instructions pointed to by the
program counter. This patch adds the missing output.
A possible output is:
Code: e1c560d0 e12fff1e e120077b e12fff1e (e7f7defb)
The parentheses indicate the instruction causing the exception.
The output can be disassembled using the decodecode script provided
by the Linux kernel project.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Following the conversion of the SPDX license tags, a number of files
compiled with -pedantic now generate warnings similar to the following
for using C99-style '//' comments in ISO C90 code:
tools/gen_eth_addr.c:1:1: warning: C++ style comments are not allowed in ISO C90
// SPDX-License-Identifier: GPL-2.0+
^
The SPDX comment-style change means that these files have adopted C99,
so need to change the language-standard to --std=gnu99 or --std=gnu11
to let the compiler know this.
As we now require GCC 6 or newer for the cross-compiler, the project has
implicitly moved the project to GNU11: let older GCC versions on various
Linux distros know to treat our host tools as GNU11 as well.
References: commit 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MMC is not initialized in SPL, so it cannot load u-boot.img
preventing boot from MMC.
Also driver specific functions are guarded with generic
configuration options which leads to build failures when device
driver is not enabled in config. Fix that by using driver
specific defines.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for loading FPGA into the SPL fitImage support. The
mechanism is flexible and allows user to override the actual
function for loading the FPGA itself. This is because on some
systems, the FPGA must be programmed to allow DRAM access, so
loading the full fitImage may not be possible if it contains
the bitstream. Instead, the spl_load_fpga_image() provides all
the tools to load the bitstream in parts while programming it
into the FPGA.
Signed-off-by: Marek Vasut <marex@denx.de>
[trini: Don't always have a branch to print out type]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a command to manipulate the bootcounter. This is useful if you can
run device recovery from inside U-Boot and need to reset the bootcounter
after executing that process as part of altbootcmd.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
For sama5d2_xplained_spiflash_defconfig, we have the demo layout
as presented on this link:
http://www.at91.com/linux4sam/bin/view/Linux4SAM/Sama5d2XplainedMainPage#SPI_eMMC_Flash_demo_Memory_map
on SPI Flash (4 Mbyte) we have Bootstrap (second level bootloader), U-boot + env
and kernel+dtb we keep on eMMC on single partition in /boot directory, formatted
with ext4.
Thus, changing the boot command to reflect this demo for the spiflash config,
and fixing up bootargs. Sama5d2_xplained does not have NAND flash, so the
bootargs were completely wrong.
Fixes: "5abc1a45": common: Move CONFIG_BOOTARGS to Kconfig
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
For sama5d2_xplained_mmc_defconfig, we have the following layout for SD-Card:
partition 1: FAT: contains bootstrap binary (second level bootloader),
U-boot, U-boot env, kernel, dtb
partition 2: EXT4: Rootfs.
Add to defconfig CONFIG_ENV_FAT_DEVICE_AND_PART to have environment
by default on SD-Card, to align with our demo layout.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Describe U_BOOT_CMD_COMPLETE.
Describe the arguments of U_BOOT_CMD and U_BOOT_CMD_COMPLETE.
Describe the arguments of the command function.
Describe the arguments of the completion function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Added a simple ls to a nonexistent directory for test 1.
In case the driver is broken for a nonexistent directory, U-boot
might crash.
Here is an example failed output:
=> # Test Case 1 - ls
=> ext4ls host 0:0
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 16384 lost+found
<DIR> 4096 SUBDIR
2621440000 2.5GB.file
1048576 1MB.file
=> # In addition, test with a nonexistent directory to see if we crash.
=> ext4ls host 0:0 invalid_d
** Can not find directory. **
./test/fs/fs-test.sh: line 161: 25786 Segmentation fault (core dumped) $UBOOT <<EOF
Subsequent tests will fail if U-boot crashes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Found a crash while issuing ext4ls with a non-existent directory.
Crash test:
=> ext4ls mmc 0 1
** Can not find directory. **
data abort
pc : [<3fd7c2ec>] lr : [<3fd93ed8>]
reloc pc : [<26f142ec>] lr : [<26f2bed8>]
sp : 3f963338 ip : 3fdc3dc4 fp : 3fd6b370
r10: 00000004 r9 : 3f967ec0 r8 : 3f96db68
r7 : 3fdc99b4 r6 : 00000000 r5 : 3f96dc88 r4 : 3fdcbc8c
r3 : fffffffa r2 : 00000000 r1 : 3f96e0bc r0 : 00000002
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
Tested on SAMA5D2_Xplained board (sama5d2_xplained_mmc_defconfig)
Looks like crash is introduced by commit:
"fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Issue is that dirnode is not initialized, and then freed if the call
to ext4_ls fails. ext4_ls will not change the value of dirnode in this case
thus we have a crash with data abort.
I added initialization and a check for dirname being NULL.
Fixes: "fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Last user of this driver went away in May 2017 in commit
eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
To support loading the zImage + DTB from the rootfs ext4 partitions,
enable the ext4 command support.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
dm_warn is too noisy, replace with dev_dbg for less noise.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
We only call fit_conf_print from one place in the code, so mark it as
static and move it up to where we call it. This in turn has us move a
few other already static functions up further as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Add an SPDX license tag to the file, saying it's GPL-2.0.
- From the Linux Kernel v4.17-rc4, import the "License identifier
syntax" section as-is from Documentation/process/license-rules.rst
and then change it to be clearer about examples from the Linux Kernel
vs examples found in U-Boot, and when we're talking about U-Boot.
Signed-off-by: Tom Rini <trini@konsulko.com>
Convert CONFIG_SUPPORT_EMMC_RPMB to Kconfig. Split the command handling
from the underlying support and expose this through CMD_MMC_RPMB.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The bcm2835 sdhost driver has a problem with "write multiple" commands.
It seems to boil down to the fact that the controller dislikes its FIFO
to get drained at the end of a block when a write multiple blocks command
is in flight.
The easy fix is to simply get rid of all the IRQ driven logic and make
the driver push as much data into the FIFO as it can. That way we never
drain and we never run into the problem.
Reported-by: Jan Leonhardt <jan@cyberdesigner.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
Back in the old days, 0x100 was used as the address to pass the device tree
from firmware into the kernel. This has since changed to a more dynamic
location, so using 0x100 actually breaks more things than it helps with.
Let's move the device tree default location for distro boot to a more sane
place that gives us enough head room in low memory.
Reported-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
- The correct way to build with thumb mode is to select SYS_THUMB_BUILD
- We should be setting -march=armv7-m in arch/arm/Makefile not the
sub-config.mk file.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Xilinx aarch64 is caught in the general xilinx arm job, exclude from
the general aarch64 job.
- Give the generic aarch64 job a better name
- Re-sort the PowerPC jobs so that we can complete them a bit quicker.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for gcc versions 7.3.0, 6.4.0 and 4.9.4.
Also use a regex for matching the tarball names. Some gcc versions
use '-ARCH-' instead of '_ARCH-'.
As part of this, we switch TravisCI to also using these toolchains for
all platforms.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
SPL and instead let full U-Boot handle it. Instead of an empty
function just do not call a function.
Signed-off-by: Tom Rini <trini@konsulko.com>
For booting Linux in the generic distro mechanism, cmd/pxe.c
retrieves the FDT file name from "fdtfile" environment variable.
Rename "fdt_file" to "fdtfile" for easier migration to distro boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add clock-names and reset-names because this node recognizes multiple
clocks and resets. ("ether", and so on, for each)
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since 'commit f82290afc8 ("mtd: ubi: Fix worker handling")',
when booting from NAND, on a fresh NAND just after being flashed (and
only in this case), we got the following log:
ubi0: default fastmap pool size: 200
ubi0: default fastmap WL pool size: 100
ubi0: attaching mtd2
ubi0: scanning is finished
ubi0 error: ubi_update_fastmap: could not find any anchor PEB
ubi0 error: ubi_update_fastmap: could not find any anchor PEB
ubi0 error: ubi_wl_get_peb: Unable to get a free PEB from user WL pool
ubi0 error: autoresize: cannot auto-resize volume 1
UBI error: cannot attach mtd2UBI error: cannot initialize UBI, error
-28UBI init error 28
After analysis, in ubi_wl_init(), when performing schedule_erase(),
thread_enabled flag is not yet set to 1, which forbids ubi_do_worker()
to execute pending works.
This has to effect to not populate ubi->free with free physical
eraseblocks.
Following Richard Weinberger's advice, this patch has been
backported from kernel tree :
'commit 1cb8f9776c7d ("ubi: fastmap: Implement produce_free_peb()")'
Tested-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Heiko Schocher <hs@denx.de>
Drop per-SoC Makefile entries and replace them with one unified entry
now that the PFC tables are gone. Shuffle the Makefile around a bit
to make it more organized.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
All the boards use new modern PFC framework, the old PFC tables
are no longer used, so remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Remove the rcar_i2c driver, since it's no longer used by any
board and will be superseded by a DM and DT capable variant.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
devm_zalloc() is already defined in dm/device.h header, so
devm_zalloc can be removed from linux_compact.h beader file.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Switch to DM_USB was done and there is no need to keep !DM_USB code in
tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove harcoded XHCI lists and detect mode, speed based on DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Serial-changes: 2
- Remove also XHCI macros from hardware.h
- Remove additional new line in zcu106
By enabling BLK by default this is the next driver which needs to get
support for DM_USB. Adding generic DWC3 glue logic which only
parse nodes and read device mode. Based on it probe proper
host/peripheral DWC3 drivers for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support to get maximum speed from dt so that usb drivers
makes use of it for DT parsing.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
(rebase and fix errors)
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is preparing dwc3 core for enabling DM_USB with peripheral
driver with using driver model support.
The driver will be bound by the DWC3 wrapper driver based on the
dr_mode device tree entry.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
(Remove dwc3-omap changes)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds phy tranceiver driver for STM32 USB PHY
Controller (usbphyc) that provides dual port High-Speed
phy for OTG (single port) and EHCI/OHCI host controller
(two ports).
One port of the phy is shared between the two USB controllers
through a UTMI+ switch.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
During file download, it only uses 32bit variable for file size and
it limits maximum file size less than 4GB. Update to support more
than 4GB file with using two 32bit variables for file size as thor
protocol 5.0.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The thor sender can send filename without null character and it is
used without consideration of overflow. Actually, character array
for filename is assigned with DEFINE_CACHE_ALIGN_BUFFER() and it
is bigger than size of memcpy, so there was no real overflow.
Fix filename overflow for code level integrity.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Preparation for Stratix 10 enablement. In ARM64, L2 cache controller is
accessed through processor registers. So, add CONFIG_SYS_L2_PL310 switch
conditional build in order this file can by shared across other SOCFPGAs.
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Clock frequency info is required in U-Boot because info would be erased
when transition from SPL to U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Enable memory allocation in SPL for preparation to enable FAT
in SPL. Memory allocation is needed by FAT to work properly.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Add function for both multiple DRAM bank and single DRAM bank size
initialization. This common functionality could be used by every single
SOCFPGA board.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
Current sdram driver is only applied to gen5 device, hence it is better
to rename sdram driver to more specific name which is related to gen5
device.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
The EMAC reset and PHY mode configuration was never working on the
Arria10 SoC, fix this. This patch pulls out the common code into
misc.c and passes the SoC-specific function call in as a function
pointer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Regenerate Altera Arria 10 SoCDK SDMMC handoff file using latest
Quartus to get the new set of clock bindings in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Synchronize Altera Arria 10 DT sources with Linux 4.16.3 as of commit
ef8216d28a5920022cddcb694d2d75bd1f0035ca
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The A10 clock manager parsed DT bindings generated by Quartus the
bsp-editor to configure the A10 clocks. Sadly, those DT bindings
changed at some point. The clock manager patch used the old ones,
this patch replaces the bindings parser with one for the new set.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Pull the serial port configuration from DT and use DM serial instead
of having the serial configuration in two places, DT and board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This was never used, is not used anywhere and is just in the way
by adding annoying ifdeffery. Get rid of it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The global data are in the .data section, so there's no point in
reserving any space for it above stack. Put stack at the end of
SRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
The DT bindings for the Arria10 clock init have changed, add another
compatible to make them work with U-Boot until a proper clock driver
gets written.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Following tests has been added for mc34708 device:
- get_test for mc34708 PMIC
- Check if proper number of registers is read
- Check if default (emulated via i2c device) value is properly read
- Check if value write/read operation is correct
- Perform tests to check if pmic_clrsetbits() is working correctly
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The common code can be excluded to be reused by tests for other PMIC.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This MC34708 PMIC is somewhat special - it used single transfers (R/W) with
3 bytes size - up till now U-Boot's PMICs only used 1 byte.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit also provides the default values of the emulated MC34708 PMIC
internal registers content.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This change enables support for MC34708 PMIC in sandbox. Now we can
emulate the I2C transfers larger than 1 byte.
Notable changes for this driver:
- From now on the register number is not equal to index in the buffer,
which emulates the PMIC registers
- The PMIC register's pool is now dynamically allocated up till
64 regs * 3 bytes each = 192 B
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Up till now it was only possible to use 'pmic' command with a single byte
transmission.
The pmic_read|write functions has been replaced with ones, which don't need
the transmission length as a parameter.
Due to that it is possible now to read data from PMICs transmitting more
data than 1 byte at once (e.g. mc34708)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds support for MC34708 PMIC, to be used with driver model
(DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit provides support for transmissions larger than 1 byte for
PMIC devices used with DM (e.g. MC34708 from NXP).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The struct uc_pmic_priv's trans_len field stores the number of types to
be transmitted per PMIC transfer.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds definition of the number of bytes sent at once by the
MC34708 PMIC.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6UL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
u-boot,dm-spl property is specific to U-Boot, so move it into
*u-boot.dtsi files for relevant i.MX6QDL files.
This make syncing Linux dts files straight forward.
Also update the MAINTAINERS file for dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When Kconfig support was added for MVGBE it included automatically
selected PHYLIB support. But MVGBE does not need PHYLIB it will build
fine without it. Commit ed52ea507f ("net: add Kconfig for MVGBE")
should have been a no-op in terms of build size but because of the
selecting PHYLIB the openrd configs increased in size.
Remove the automatic selection of PHYLIB, boards that need it will have
already enabled it in their config header file.
Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable device tree control in
u-boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts file from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import the dts files from Linux 4.17 and enable CONFIG_OF_CONTROL.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
These files are taken verbatim from the Linux kernel 4.17
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The SION pin must be set for proper operation of I2C when DM is enabled.
When legacy I2C is used, this bit is set implicitly in the u-boot code:
arch/arm/include/asm/arch-mx5/iomux-mx53.h:92:
MX53_PAD_KEY_ROW3__I2C2_SDA = IOMUX_PAD(0x368, 0x040, 4 |
IOMUX_CONFIG_SION, 0x820, 0, NO_PAD_CTRL),
The Linux kernel uses similar approach with:
arch/arm/boot/dts/imx53-tqma53.dtsi:182:
MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000
After applying this patch it is possible to have the I2C working with DM
on imx53 devices:
MX53_PAD_KEY_ROW3__I2C2_SDA (0x1ee | IMX_PAD_SION)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
CONFIG_ENV_IS_IN_MMC must be declared in defconfig to properly
support "env save".
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The mx6_common.h file already defines BOUNCE_BUFFER so no need to
definit it again in specific configs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
It makes sense to select the MP multi processor option at the same time we
select the other SMP options needed for SMP capable i.MX6 SoCs.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Also remove the #ifdef's from clock.h since the Kconfig values defaults
the to old default values in clock.h.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move CONFIG_MX31 from mx31pdk.h to mx31pdk_defconfig and introduce
necessary Kconfig changes as well.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This replaces TARGET_GE_B{4,6,8}50V3 with common TARGET_GE_BX50V3.
The boards are identified automatically at runtime.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
B{46}50v3s have an internal LCD that needs to be configured,
in comparison with B850v3 which has only external displays.
Use VPD instead of `CONFIG_TARGET_GE_B{4,6,8}50V3' compile-time
checks to correct initialize video based on the monitor type.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Move the VPD reading earlier in order to establish the monitor
type as soon as possible.
The configuration of the specific environment variables needs to be
done later after the environment is configured.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Simplify process_vpd() by unifying the switch statements handling
product specific configurations.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The detect_baseboard() function actually determines whether there is an
internal LCD panel or not. Rename for clarity.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This was unintentionally disabled when moving MVGBE to Kconfig.
Fixes: commit ed52ea507f ("net: add Kconfig for MVGBE")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
In
void *rx_addr = NULL;
rx_add = A;
the first assignment has no effect. Remove it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For SPI_XFER_BEGIN | SPI_XFER_END the code sets data_out = NULL.
In the debug statement we should not dereference this value.
As we do not transfer any data the debug statement is not needed in this
case anyway.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In some situation, QSPI controller is already configured by an early
boot stage, adding reset support will insure that QSPI controller is
started from a pristine state.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Quad-SPI interface is able to manage 2 spi nor devices.
FSEL bit selects the flash memory to be addressed in single flash mode.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add "st,stm32f469-qspi" compatible which is used on kernel side.
This will be necessary when DT will be synchronised from kernel.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As all platforms which uses this driver have CONFIG_CLK flag
enable in their defconfig, we can remove it from driver code.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When the U-Boot base directory happens to have the same name as the branch
that buildman is directed to use via the '-b' option and no output
directory is specified with '-o', buildman happily starts removing the
whole U-Boot sources eventually only stopped with the error message:
OSError: [Errno 20] Not a directory: '../<branch-name>/boards.cfg
Add a check to avoid this and also deal with the case where '-o' points
to the source directory, or any subdirectory of it.
Finally, tidy up the confusing logic for removing the old tree when using
-b. This is only done when building a branch.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Lothar Waßmann <LW@KARO-electronics.de>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
To address that situation we discussed on the list moving to
genetic_set_bit() instead.
Doing a quick grep for similar situations in drivers/usb shows that the
composite device is using __set_bit().
This patch switches over to generic_set_bit to maintain consistency between
the two gadget drivers.
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
Compiling the f_mass_storage driver for an x86 target results in a
compilation error as set_bit and clear_bit are provided by bitops.h
Looking at the provenance of the current u-boot code and the git change
history in the kernel, it looks like we have a local copy of set_bit and
clear_bit as a hold-over from porting the Linux driver into u-boot.
These days __set_bit and __clear_bit are optionally provided by an arch and
can be used as inputs to generic_bit_set and generic_bit_clear.
This patch switches over to generic_set_bit and generic_clear_bit to
accommodate.
Tested on i.MX WaRP7 and Intel Edison
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Marek Vasut <marex@denx.de>
nds2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nds32 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
nds32 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nds32
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Macpaul Lin <macpaul@andestech.com>
nios2 bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
nios2 bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
nios2 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in nios2
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Thomas Chou <thomas@wytron.com.tw>
riscv bitops.h provides a __clear_bit() but does not define
PLATFORM__CLEAR_BIT as a result generic_clear_bit() is used instead of the
architecturally provided __clear_bit().
This patch defines PLATFORM__CLEAR_BIT which means that __clear_bit() in
riscv bitops.h will be called whenever generic_clear_bit() is called - as
opposed to the default cross-platform generic_clear_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
riscv bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Rick Chen <rick@andestech.com>
Cc: Greentime Hu <green.hu@gmail.com>
x86 bitops.h provides a __set_bit() but does not define PLATFORM__SET_BIT
as a result generic_set_bit() is used instead of the architecturally
provided __set_bit().
This patch defines PLATFORM__SET_BIT which means that __set_bit() in x86
bitops.h will be called whenever generic_set_bit() is called - as opposed
to the default cross-platform generic_set_bit().
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
mv_ddr_build_message.c is generated in Marvell's standalone mv_ddr code.
When imported into u-boot we need to add the appropriate SPDX tag and
re-format it slightly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This commit adds basic support for PWM found on Allwinner A64.
It can be used for pwm_backlight driver (e.g. for Pinebook)
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Currently dw_hdmi configures HSYNC polarity using VSYNC setting from
EDID and vice versa. Fix it, since it breaks displays where HSYNC
and VSYNC polarity differs
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
When the following configuration is set
# CONFIG_CMD_DHCP is not set
CONFIG_CMD_BOOTP=y
CONFIG_BOOTP_NTPSERVER=y
The following compile error is observed
error: used struct type value where scalar is required
if (net_ntp_server)
^~~~~~~~~~~~~~
Resolve this by checking net_ntp_server.s_addr instead.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a Kconfig option for BOOTP_NTPSERVER to enable the DHCP/BOOTP option
to configure the sntp server address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The CONFIG_PHY_MARVELL has already been migrated to Kconfig (some boards
already had it in their Kconfig), but had not been moved for older
boards.
Move it to the defconfigs for all boards.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DTS file for armada-37xx uses the string "marvell,armada3700-ehci",
but the code searched for "marvell,armada-3700-ehci".
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Make ddr3_calc_mem_cs_size() global scope and use it in
ddr3_new_tip_ecc_scrub to correctly initialize all of DDR memory.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This restores support for configuring the timing mode based on the
ddr_topology. This was originally implemented in commit 90bcc3d38d
("driver/ddr: Add support for setting timing in hws_topology_map") but
was removed as part of the upstream sync.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This syncs drivers/ddr/marvell/a38x/ with the mv_ddr-armada-17.10 branch
of https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
The upstream code is incorporated omitting the ddr4 and apn806 and
folding the nested a38x directory up one level. After that a
semi-automated step is used to drop unused features with unifdef
find drivers/ddr/marvell/a38x/ -name '*.[ch]' | \
xargs unifdef -m -UMV_DDR -UMV_DDR_ATF -UCONFIG_DDR4 \
-UCONFIG_APN806 -UCONFIG_MC_STATIC \
-UCONFIG_MC_STATIC_PRINT -UCONFIG_PHY_STATIC \
-UCONFIG_64BIT
INTER_REGS_BASE is updated to be defined as SOC_REGS_PHY_BASE.
Some now empty files are removed and the ternary license is replaced
with a SPDX GPL-2.0+ identifier.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
No in-tree code defines SUPPORT_STATIC_DUNIT_CONFIG or
STATIC_ALGO_SUPPORT. Remove ddr3_a38x_mc_static.h and use unifdef to
remove unused sections in the rest of the ddr/marvell/a38x code.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Move sys_env_device_rev_get() from the ddr training code to
sys_env_lib.c (which currently resides with the serdes code). This
brings sys_env_device_rev_get() into line with sys_env_device_id_get()
and sys_env_model_get().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
PEX_CFG_DIRECT_ACCESS was defined in ddr3_hws_hw_training_def.h despite
only being used in the serdes code. Move this definition to ctrl_pex.h
where all the other PEX defines are. Also remove the duplicate
definition of PEX_DEVICE_AND_VENDOR_ID which is already defined in
ctrl_pex.h.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds basic support for the Turris Mox board from CZ.NIC, which is
currently being crowdfunded on Indiegogo.
Turris Mox is as modular router based on the Armada 3720 SOC (same as
EspressoBin).
The basic module can be extended by different modules. The device tree
binary for the kernel can be dependent on which modules are connected,
and in what order. Because of this, the board specific code creates
in U-Boot a variable called module_topology, which carries this
information.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This adds support for the CPU watchdog found on Marvell Armada 37xx
SoCs.
There are 4 counters which can be set as CPU watchdog counters.
This driver uses the second counter (ID 1, counting from 0)
(Marvell's Linux also uses second counter by default).
In the future it could be adapted to use other counters, with
definition in the device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The driver does not check id phy_connect failed (for example on wrong
property name in device tree). In such a case a fault occurs and the
CPU is restarted.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Move the reg_set* functions into comphy.h as static inline functions.
Change return type of get_*_string to const char *.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for the clk dump command on Armada 37xx.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Since now we have driver for clocks on Armada 37xx, use it to determine
SQF clock frequency for the SPI driver.
Also change the default config files for Armada 37xx devices so that
the clock driver is enabled by default, otherwise the SPI driver cannot
be enabled.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The drivers are based on Linux driver by Gregory Clement.
The TBG clocks support only the .get_rate method.
- since setting rate is not supported, the driver computes the rates
when probing and so subsequent calls to the .get_rate method do not
read the corresponding registers again
The peripheral clocks support methods .get_rate, .enable and .disable.
- the .set_parent method theoretically could be supported on some clocks
(the parent would have to be one of the TBG clocks)
- the .set_rate method would have to try all the divider values to find
the best approximation of a given rate, and it doesn't seem like
this should be needed in U-Boot, therefore not implemented
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In SGMII initialization PIN_PIPE_SEL has to be zero when resetting
the PHY. Since comphy_mux already set the selector register to
correct values, we have to store it's value before setting it to 0
and restore it after SGMII init.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Lane 0 supports SGMII1 and USB3.
Lane 1 supports SGMII0 and PEX0.
Lane 2 supports SATA0 and USB3.
This is needed for Armada 37xx.
This introduces new device tree bindings. AFAIK there is currently no
driver for Armada 37xx comphy in Linux. When such a driver will be
pushed into Linux, this will need to be rewritten accordingly.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The register addresses on lanes 0 and 1 are switched, first comes 1 and
then 0.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently comphy_mux supports only trivial order of nodes in pin
selector register, that is lane N on position N*bitcount.
Add support for nontrivial order, with map stored in device tree
property mux-lane-order.
This is needed for Armada 37xx.
As far as I know, there is no driver for Armada 37xx comphy in the
kernel. When such a driver comes, this will need to be rewritten to
support the device tree bindings from the kernel.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit is based on commit d9899826 by
zachary <zhangzg@marvell.com>
from u-boot-marvell, see
github.com/MarvellEmbeddedProcessors/u-boot-marvell/commit/d9899826
- According to design specification, the transmitter should be set to high
impedence mode during electrical idle. Thus transmitter should detect RX
at high impedence mode also, and delay is needed to accommodate high
impedence off latency. Otherwise the USB3 will have detection issue that
most of the time the USB3 device can not be detected at all, or be
detected as USB2 device sometimes.
Modified registers: RD005C302h (R181h) (0051h) Lane Configuration 1
Bit 6: set to 1 to let Tx detect Rx at HiZ mode
Bit [3:4]: set to 2 to be delayed by 2 clock cycles
Bit 0: set to 1 to set transmitter to high impedance mode during idle.
- USB3 De-emphasize level of -3.5dB is mandatory, but USB3 MAC selects 0x2
(emphasize disabled) in the MAC_PHY_TXDEEMPH [1:0], while it is supposed
to select 0x1(3.5dB emphasize). Thus need to override what comes from
the MAC(by setting register 0x1c2 bit2 to 0x1) and to configure the
overridded values of MAC_PHY_TXDEEMPH [1:0] to 0x1(bit15 of register
0x181 and bit0 of register 0x180).
- According to USB3 application note, need to update below comphy
registers:
Set max speed generation to USB3.0 5Gbps(set RD005C04Ah bit[11:10] to 1)
Set capacitor value to 0xF(set RF005C224 bit[3:0] to 0xF)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
According to specification, CFG_PM_RXDLOZ_WAIT should be set to 0x7
when reference clock is at 25 MHz. The specification (at least the
version I have) does not mentoin the setting for 40 MHz reference
clock, but Marvell's U-Boot sets 0xC in that case.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When USB3 is on comphy lane 2 on the Armada 37xx, the registers
have to be accessed indirectly via SATA indirect access.
This is the case of the Turris Mox board from CZ.NIC.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Create a special function for indirect register setting,
reg_set_indirect, and use it instead of the two calls to reg_set.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
In U-Boot it is usually written this way.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The timeout is set to PLL_LOCK_TIMEOUT in every call to
comphy_poll_reg. Remove this parameter from the function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently there is for each register special functional macro, ie:
LANE_CFG1_ADDR(u)
GLOB_CLK_SRC_LO_ADDR(u)
...
where can be either PCIE or USB3.
Change this to one function PHY_ADDR(unit, addr). The code becomes:
phy_addr(PCIE, LANE_CFG1)
phy_addr(PCIE, GLOB_CLK_SRC_LO)
...
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The macro phy_write16 is not used by the rest of the code,
phy_read16 is not used at all.
We also change the macro SGMIIPHY_ADDR to a static inline function.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
All the calls to reg_set and friends have to cast the first argument
to void __iomem *. Lets change the return type of the MVEBU_REG macro
instead.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Drop all the extra content from the MMC core, so that tiny MMC support
is really tiny, no fancy anything. That means the tiny MMC support does
only 1-bit transfers at default speed settings. Moreover, this patch
drops duplicate instance of struct mmc mmc_static, which wasted about
360 bytes. Furthermore, since MMC tiny supports only one controller
at all times, get rid of mallocating the ext csd backup and replace
it with static array. All in all, this patch saves ~4 kiB of bloat
from the MMC core, which on platforms with severe limitations can be
beneficial.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup checkpatch.pl style warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
Correct the SPDX tag format.
Fixes: 3b52847a45 ("Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze")
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx changes for v2018.07
microblaze:
- Align defconfig
zynq:
- Rework fpga initialization and cpuinfo handling
zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING
zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation
mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode
nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params
scsi:
- convert ceva sata to UCLASS_AHCI
timer:
- Add Cadence TTC for ZynqMP r5
watchdog:
- Minor cadence driver cleanup
This patch reads the capabilities register1 and update the host
caps accordingly for mmc layer usage. This patch mainly reads
for UHS capabilities inorder to support SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to invoke any platform specific tuning
and delay routines if available.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new hooks for any platform specific tuning and
tap delays programing. These are needed for supporting
SD3.0.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support to disable clock if clk_disable
was set and then enable or set clock if the clock was changed
or clock was disabled when clock needs to be enabled.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed the datatype of variable "start" from uint to ulong
to work properly on 64-bit machines as well. Also the return type of
get_timer() function is ulong.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The officially described way to generate boot.bin files for ZynqMP is to
describe the contents of the target binary using a file of the "bif"
format. This file then links to other files that all get packed into a
bootable image.
This patch adds support to read such a .bif file and generate a respective
ZynqMP boot.bin file that can include the normal image and pmu files, but
also supports image partitions now. This makes it a handy replacement for
the proprietary "bootgen" utility that is currently used to generate
boot.bin files with FSBL.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynqmpimage.c and the new zynqmpbif.c files are all maintained by
Xilinx for the Zynq platforms. Let's match them accordingly
in the MAINTAINERS file.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We will add support for ZynqMP bif input files later, so let's move
all structure definitions into a header file that can be used by that
one as well.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The zynqmp image format has support for inline partitions which are
used by FSBL to describe payloads that are loaded by FSBL itself.
While we can't create images that contain partitions (yet), we should
still at least be able to examine them and show the user what's inside
when we analyze an image created by bootgen.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DISPLAY_BOARDINFO in OF case show model identification string from DT.
Enable this feature instead of custom IDENT_STRING which does the same
thing.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Call calloc for space allocation only at one location and include if/else
to sprintf. This will simplify run time device adding based on id aliases.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch fills the MMU map for DDR at run time based on information read
from Device Tree or automatically detected from static configuration.
The patch is needed because for systems which has for example 1GB of memory
but MMU map is 2GB there could be spurious accesses which was seen in past
when mapping is not fitting with actual memory installed.
Signed-off-by: Nitin Jain <nitin.jain@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog on zcu100 to make sure if there is a bug in the u-boot
there is proper reset.
Watchdog expires and PMU fw is informed and based on setting proper
action is taken.
The patch is enabling reset-on-timeout feature and also fixing fixed
clock rate for watchdog where 100MHz is max (and also default) clock value.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable watchdog in full U-Boot.
Similar changes were done by:
"arm: zynq: Wire watchdog internals"
(sha1: e6cc3b25d7)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Debug message was showing timeout value which was passed to start
function but there is a checking if this value can be setup.
The patch is moving this debug printf function below checking.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Send address cycles as per value read from onfi parameter
page for Read and write commands instead of using a
hard coded value. This may vary for different parts and
hence use it from onfi parameter page value.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for 16-bit buswidth by determining
the bus width based on mio configuration.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch enables support zc1275 revB board. It has
SD added compared to revA. The same configuration will
work for RevC boards aswell.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In v2018 the patch
"dm: ahci: Correct uclass private data"
(sha1: bfc1c6b483)
was causing an issue for ceva_sata.
But this issue is not in v2018.05-rc1 but still converting to
UCLASS_AHCI would make more sense.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Now that showing silicon version is part of the CPU
info display, let's remove checkboard().
Note that the generic show_board_info() will still
show the DT 'model' property. For instance:
U-Boot 2018.05-rc2-00025-g611b3ee0159b (Apr 19 2018 - 11:23:12 +0200)
CPU: Zynq 7z045
Silicon: v1.0
Model: Zynq ZC706 Development Board
I2C: ready
Based on patches from Ariel D'Alessandro <ariel@vanguardiasur.com.ar>,
and Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
mini configuration doesn't need to show this information.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In past this code was commented and was used for debug purpose.
But there is no reason not to enabled it based on macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Avoid creating incorrect comments like /* ...*/... */ by printing
'.' instead of '*' inside comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Without the patch gcc 8 produces:
warning: ignoring attribute ‘noreturn’ because it conflicts with
attribute ‘const’ [-Wattributes]
int ____ilog2_NaN(void);
So let's update the include from Linux kernel v4.16.
This removes static checks of ilog2() arguments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Every va_start() call must be matched by a va_end() call.
scripts/checkpatch.pl required reformatting the complete function
zm_dprintf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The check for having a memory node within the fdt blob is made wrong, we
fix this here.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Attempting to build with both DEBUG and CONFIG_USE_TINY_PRINTF along
with CONFIG_SPL_YMODEM_SUPPORT fails at link time:
common/built-in.o: In function `zm_dprintf':
common/xyzModem.c:190: undefined reference to `vsprintf'
Disable Ymodem debug if we don't have full vsprintf support.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.
Remove all invalid fsl email addresses and mark the boards as orphan.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch is necessary for providing basic bootcount checking in the case
of using "falcon" boot mode in that board.
It forces u-boot proper boot, when we exceed the number of errors.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch adds support for incrementation of the bootcount in SPL.
Such feature is necessary when we do want to use this feature with
'falcon' boot mode (which loads OS directly in SPL).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The code has been refactored to use common wrappers from bootcount.h
header.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Those two functions can be used to provide easy bootcount management.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
New, SPL related config option - CONFIG_SPL_BOOTCOUNT_LIMIT has been
added to allow drivers/bootcount code re-usage in SPL.
This code is necessary to use and setup bootcount in SPL in the case of
falcon boot mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Allow optionally bringing up the Apalis type specific 4 lane PCIe port
as well as the PCIe switch as found on the Apalis Evaluation board. In
order to avoid violating the PCIe reset timing do this by overriding the
tegra_pcie_board_port_reset() function. Note however that both the
Apalis type specific 4 lane PCIe port as well as the regular Apalis PCIe
port are also left disabled in the device tree by default.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix optional Apalis type specific 4 lane PCIe port 0 and Apalis PCIe
port 1 pin muxing.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
It turns out that the current PCIe reset implementation in the PCIe
board init function is not quite working reliably due to PCIe reset
timing violations. Fix this by overriding the
tegra_pcie_board_port_reset() function.
Also allow optionally bringing up the PCIe switch as found on the Apalis
Evaluation board. Note however that the Apalis PCIe port is also left
disabled in the device tree by default.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Just like the already present as3722_sd_set_voltage() add the currently
missing signature of the as3722_ldo_set_voltage() function to its header
file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Introduce a weak tegra_pcie_board_port_reset() function by default
calling the existing tegra_pcie_port_reset() function. Additionally add
a tegra_pcie_port_index_of_port() function to retrieve the specific PCIe
port index if required. This allows overriding the PCIe port reset
functionality from board specific code as e.g. required for Apalis T30
and Apalis TK1.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix ldo_get_enable() and ldo_set_enable() functions for LDOs with an
index > 7. Turns out there are actually two separate AS3722_LDO_CONTROL
registers AS3722_LDO_CONTROL0 and AS3722_LDO_CONTROL1. Actually make use
of both. While at it also actually use the enable parameter of the
ldo_set_enable() function which now truly allows disabling as opposed to
only enabling LDOs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
As the AS3722 GPIO0 is also a not connected on our Apalis TK1 module
explicitly configure it to high-impedance as well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Trying to boot from an ext4 rootfs fails due to us defaulting to ext3.
While the downstream T20/T30 L4T kernel has issues with ext4 later TK1
L4T should work just fine with it. Hence enable ext4 for sdboot and
usbboot on TK1.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-Boot on Harmony recently got broken by ongoing driver model resp. live
tree migration work:
U-Boot 2018.03-rc3 (Feb 21 2018 - 15:43:08 +0100)
TEGRA20
Model: NVIDIA Tegra20 Harmony evaluation board
Board: NVIDIA Harmony
DRAM: 1 GiB
Video device 'dc@54200000' cannot allocate frame buffer memory -ensure
the device is set up before relocation
Error binding driver 'tegra_lcd': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 3ffa86d0 failed at call 00121dc0 (err=-28)
This commit fixes this by enabling live tree, MTD and UBI for Harmony as
well.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra NAND driver recently got broken by ongoing driver model resp.
live tree migration work:
NAND: Could not decode nand-flash in device tree
Tegra NAND init failed
0 MiB
A patch for NAND uclass support was proposed about a year ago:
https://patchwork.ozlabs.org/patch/722282/
It was not merged and I do not see on-going work for this.
This commit just provides a driver model probe hook to retrieve further
configuration from the live device tree. As there is no NAND ulass as of
yet (ab)using UCLASS_MTD. Once UCLASS_NAND is supported, it would be
possible to migrate to it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Updated copyright info for the issues reported after running
check-legal test.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per the IFC hardware manual, Most significant byte in nand_fsr
register is the outcome of NAND READ STATUS command.
So status value need to be shifted as per the nand framework
requirement.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Mask HRESET_B after cleared the the RCW_SRC, because in the workaround
we override the RCW_SRC and if HRESET_B is issued after the override
then SoC cannot find valid RCW as the RCW_SRC was overwritten and
result in hang. So we need to mask HRESET_B in case user asserts it,
and the PORESET_B should be asserted which leads to resampling of
cfg_rcw_src pins and loading of correct RCW_SRC.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
JR3 was getting removed from device tree only if random number
generation was successful. However, if SEC firmware is present,
JR3 should be removed from device tree node irrespective of the
random seed generation as SEC firmware reserves it for it's use.
Not removing it in case of random number generation failure causes
the kernel to crash.
Random number generation was being called twice. This is not
required. If SEC firmware is running, SIP call can be made to the SEC
firmware to get the random number. This call itself would return
failure if function is not supported. Duplicate calling of random
number generation function has been removed.
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
TZASC controller configurations are similar. Put them in a macro and
avoid code duplication.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Number of ECC status registers i.e. (ECCSTATx) has been increased in
IFC version 2.0.0 due to increase in SRAM size. This is causing
eccstat array to over flow.
So, replace eccstat array with u32 variable to make it fail-safe and
independent of number of ECC status registers or SRAM size.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Some SoCs have different endianness of QSPI IP if compared
to endianness of core. The function is_controller_busy()
checks if the QSPI controller is busy or not, considering
the endianness of the QSPI IP.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch solves assert failed displayed in the console during a boot.
The root cause is that the ubifs_inode is not already allocated when
ubifs_printdir and ubifs_finddir functions are called.
Trace showing the issue:
feed 'boot.scr.uimg', ino 94, new f_pos 0x17b40ece
dent->ch.sqnum '7132', creat_sqnum 3886945402880
UBIFS assert failed in ubifs_finddir at 436
INODE ALLOCATION: creat_sqnum '7129'
Found U-Boot script /boot.scr.uimg
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In do_bootm_states when doing BOOTM_STATE_LOADOS we use load_end
uninitialized and Coverity notes this now. This however leads down
another interesting path. We pass this pointer to bootm_load_os and
that in turn uses this uninitialized value immediately to calculate the
flush length, and is wrong. We do not know what load_end will be until
after bootm_decomp_image is called, so we must only set flush_len after
that. All of this also makes it clear that the only reason we pass a
pointer for load_end to bootm_load_os is so that we can call lmb_reserve
on success. Rather than initialize load_end to 0 in do_bootm_states we
can just call lmb_reserve ourself.
Reported-by: Coverity (CID: 175572)
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The signature/hash information are displayed for images but nor for
configurations.
Add subnodes printing in fit_conf_print() like it's done in fit_image_print()
Signed-off-by: Clément Péron <peron.clem@gmail.com>
[trini: Add guards around fit_conf_print to avoid warnings]
Signed-off-by: Tom Rini <trini@konsulko.com>
find_next_zero_bit() incorrectly handles cases when:
- total bitmap size < 32
- rest of bits to process
static inline int find_next_zero_bit(void *addr, int size, int offset)
{
unsigned long *p = ((unsigned long *)addr) + (offset >> 5);
unsigned long result = offset & ~31UL;
unsigned long tmp;
if (offset >= size)
return size;
size -= result;
offset &= 31UL;
if (offset) {
tmp = *(p++);
tmp |= ~0UL >> (32-offset);
if (size < 32)
[1]
goto found_first;
if (~tmp)
goto found_middle;
size -= 32;
result += 32;
}
while (size & ~31UL) {
tmp = *(p++);
if (~tmp)
goto found_middle;
result += 32;
size -= 32;
}
[2]
if (!size)
return result;
tmp = *p;
found_first:
[3] tmp |= ~0UL >> size;
^^^ algo can reach above line from from points:
[1] offset > 0 and size < 32, tmp[offset-1..0] bits set to 1
[2] size < 32 - rest of bits to process
in both cases bits to search are tmp[size-1..0], but line [3] will simply
set all tmp[31-size..0] bits to 1 and ffz(tmp) below will fail.
example: bitmap size = 16, offset = 0, bitmap is empty.
code will go through the point [2], tmp = 0x0
after line [3] => tmp = 0xFFFF and ffz(tmp) will return 16.
found_middle:
return result + ffz(tmp);
}
Fix it by correctly seting tmp[31..size] bits to 1 in the above case [3].
Fixes: 81e9fe5a29 ("arm: implement find_next_zero_bit function")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Declaration of indirect PCI bridges is not compatible with DM: Both
define PCI operations, but in different ways. Hence, don't use indirect
bridges if DM is active.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make the ihs_mdio driver DM-compatible, while retaining the old
functionality for not-yet-converted boards.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The clock node is used by the serial driver and it's needed
before relocation.
This patch ensures that the msm-serial driver can actually
use the clock node.
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
STiH410 has 2 PHYs wired on the DWC3 IP, USB2 and USB3 PHYs.
As currently no U-boot driver is available for the USB3 PHY and to avoid
issue during DWC3 drive probe, we use DWC3 IP with only USB2 PHY
using stih410-b2260-u-boot.dtsi file.
Fixes: 2fd4242cc5 ("ubs: xhci-dwc3: Enable USB3 PHY when available")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Eliminate code duplication: the same PARTS_DEFAULT was defined in
am57xx_evm.h and in dra7xx_evm.h. Extract it to environment/boot.h and
use in all OMAP5-based boards.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Add support for the SoCFPGA header v1 , which is used on Arria 10.
Thus far the mkimage-socfpga image only supported header format v0
used on Cyclone V and Arria V, but is not supported on Arria 10.
The layout of the v0 and v1 header is similar, yet there are a few
differences, see the patch body for details.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
The structure is passed around correctly, create local instances
where necessary and zap the global struct socfpga_image instance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
Add support for the SoCFPGA header v1, which is used on Arria 10.
The layout of the v0 and v1 header is similar, yet there are a few
differences which make it incompatible with previous v0 header, so
add a new entry.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
The Arria10 uses slightly different boot image header than the Gen5 SoCs,
in particular the header itself contains an offset from the start of the
header to which the Arria10 jumps. This offset must not be negative, yet
the header is placed at offset 0x40 of the bootable binary. Therefore, to
jump into U-Boot, add a trampoline just past the Arria10 boot header and
point to this trampoline at fixed offset from the header generated using
the mkimage -T socfpgaimage_v1 . Note that it is not needed to jump back
to offset 0x0 of the image, it is possible to jump directly at the reset
label and save processing two instructions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Chin Liang See <chin.liang.see@intel.com>
This patch adds the driver for the Amlogic Meson Successive Approximation
Register (SAR) A/D Converter based on the Linux IIO driver thanks to the
great work of Martin Blumenstingl.
The driver has been adapted to U-Boot and the ADC UClass.
This patch depends on the regmap "regmap: add regmap_update_bits() helper"
patch and has been tested using the newly introducted "adc" CLI command
in the "cmd: add ADC cli commands" patch.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add calls to regmap_read/modify_bits/write even if the proper memory
read/write calls are not executed in sandbox.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the regmap_update_bits() to simply the read/modify/write of registers
in a single command. The function is taken from Linux regmap
implementation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add VREF clock gating, that may be used by STM32 VREFBUF regulator.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable DM_REGULATOR_STPMU1 flag to activate regulator
driver for STM32MP15 SoC and CMD_REGULATOR flag to be
able to set/get regulator state int U-boot command line.
Disable PMIC_CHILDREN as this flag is not needed in SPL
for STM32MP1.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add regulator bindings to get access to regulator managed
by drivers/power/regulator/stpmu1.c regulator driver.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable support for the regulator functions of the STPMU1X PMIC. The
driver implements get/set api for the various BUCKS and LDOs supported
by the PMIC device. This driver is controlled by a device tree node
which includes voltage limits.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This driver binds and manages the following regulator of
SoC's PWR block :
- reg11
- reg18
- usb33
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since kirkwook SPI was recently converted to DM, add compatible strings
to the SPI flash devices to make them work with the new driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Enable the FDT library overlay support for all TI SOC family.
Without this option, when Loading fdt from FIT image, the
following warning is seen.
"config with overlays but CONFIG_OF_LIBFDT_OVERLAY not set".
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Suggested-by: Andrew F.Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
'commit dda0bd674481 ("arm: dra762: Add support for device package identification")'
introduces ABZ and ACD package identification.
This patch is to extend usage of "fastboot getvar cpu" for
DRA76x ABZ and ACD devices.
Helps in fixing the boot warning.
Warning: fastboot.cpu: unknown CPU rev: 123863298
on
CPU : DRA762-GP ES1.0 ABZ package
Model: TI AM5748 IDK
Board: AM574x IDK REV 1.0A
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove SYS_USE_NANDFLASH, SYS_USE_MMC as they are deprecated and
unused.
The board configurations already use CONFIG_SD_BOOT and
CONFIG_NAND_BOOT respectively.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[eugen.hristev@microchip.com: rework on latest u-boot]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
According to the REVB schematic, fix the USB vbus power enable pin.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
To fix the issue of write the rootfs.ubi, adjust the smc timings
configuration of the nand controller.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
The drive strength has to be set to medium for the NAND data lines.
With a low drive, we can get some data corruption.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Add PCIe driver for Intel FPGA PCIe IP. This driver operates the PCIe IP in
rootport mode only, the EP mode is not supported. The driver is tested
with the Intel e1000e NIC driver.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
This patch adds smc and hvc commands, that allow issuing Secure Monitor
Calls and Hypervisor Calls conforming to the ARM SMC Calling Convention.
Add Kconfig items to allow each command can be individually enabled.
Signed-off-by: Michalis Pappas <mpappas@fastmail.fm>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pinctrl bindings has changed for Amlogic Meson SoCs since Linux 4.13,
update the pinctrl driver to take this in account.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Taking into account the Amlogic Family name starts with GX, including
the GXBB, GXL and GXM SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested By: Bruno Herrera <bruherrera@gmail.com>
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
dm: led: add testcase for "default-state" property
Add two more gpio-leds to sandbox test device tree with default-state
property set to "on"/"off".
Add dm_test_led_default_state() to check that these new LED's are set to
LEDST_ON and LEDST_OFF.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
To avoid board specificy LED activation code, automatically
activate gpio-leds with "default-state" property during bind().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Add support for the device tree property "default-state". This feature
might be useful for LEDs indicating "power on" or similar states.
Note: Even with this commit gpio-leds remain in reset state. That's
because the led_gpio is not probed until DM_FLAG_ACTIVATED is set.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Provide an alternate path for sparse-images to be
written to MMC. For example, via tftp on platforms
that don't support fastboot protocol. Or when an
image is to written at some offset, rather than the
start of a partition.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
[trini: Guard with CONFIG_FASTBOOT_FLASH tests, use LBAF for lbaint_t
printing]
Signed-off-by: Tom Rini <trini@konsulko.com>
On a socfpga_cyclone5 based board the SD card, was never powered up. For
other dw_mmc based SoCs dwmci_probe() is called in the platform specific
probe(). It seems this call is missing for socfpga_dw_mmc.
With this change DWMCI_PWREN is set by dmwci_init().
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add the debug message for checking the mmc clock status.
It's helpful to debug the controlling clock.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
mmc_set_clock() function has the disable argument as bool type.
When mmc_set_clock is called, it might be passed to "true" or "false".
But it's too confusion whether clock is enabled or disabled with only
"true" and "false".
To prevent the confusion, replace to MMC_CLK_ENABLE/DISABLE macro from
true/false.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
max77686 pmic is supporting with max77686.c under pmic/ and regulator/
direnctroy. Remove pmic_max77686.c what didn't use anywhere.
Instead, enable CONFIG_DM_REGULATOR_MAX77686 and
CONFIG_DM_PMIC_MAX77686.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Currently, the UniPhier pinctrl drivers expose only the pin-group
interface to device tree.
Provide .get_pins_count, .get_pin_name, .pinconf_set hooks to support
pin configuration via 'pins' DT property.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The #include <linux/bug.h> is here to use BUILD_BUG_ON_ZERO().
By replacing it with <linux/build_bug.h>, we can reduce the number of
headers pulled in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since commit f73cfb4d0d ("pinctrl: uniphier: simplify input enable
and delete pin arrays"), these data are no longer used in any useful
way. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
write_sparse_image could be useful for non-fastboot users.
For ex a platform, without usb-device/fastboot support, could
get sparse images over tftp and write using the mmc command.
Or non-android systems could also leverage the sparse format.
Towards that, this patch removes anything fastboot specific from
the write_sparse_image implementation. Which includes making the
function return integer as error code and calls for fastboot logging
via an optional callback function 'mssg'.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Cache maintenance procedure is same for v7A and v7R
processors. So re-use cache-cp15.c file except for
mmu parts.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Cortex-R* processors are a mid-range CPUs for use in deeply-embedded,
real-time systems. It implements the ARMv7-R architecture, and includes
Thumb-2 technology for optimum code density and processing throughput.
Except for MPU(Memory Protection Unit) and few CP15 registers, most of the
features are compatible with v7 architecture. So,reuse the same armv7
folder and introduce a new config CPU_V7R in order to differentiate
from v7 based platforms.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain ARM architectures like ARMv7-A, ARMv7-R has support for
enabling caches using CP15 registers. To have a common support
for all these architectures, introduce a Kconfig symbol
SYS_ARM_CACHE_CP15 that selects cache-cp15.c
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add a Kconfig entry for MMU and imply for all platforms using
cache-cp15.c containing MMU setup. Using imply instead of select so that
MMU can be disabled by defconfigs when not needed.
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Not all ARM V7 based cpus has VBAR for remapping
vector base address. So, update VBAR only if it available.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Like Linux, syscon_node_to_regmap() allows a node to work as a syscon
provider without binding it to a syscon driver. Test this.
Requested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The syscon implementation in U-Boot is different from that in Linux.
Thus, DT files imported from Linux do not work for U-Boot.
In U-Boot driver model, each node is bound to a dedicated driver
that is the most compatible to it. This design gets along with the
concept of DT, and the syscon in Linux originally worked like that.
However, Linux commit bdb0066df96e ("mfd: syscon: Decouple syscon
interface from platform devices") changed the behavior because it is
useful to let a device bind to another driver, but still work as a
syscon provider.
That change had happened before U-Boot initially supported the syscon
driver by commit 6f98b7504f ("dm: Add support for generic system
controllers (syscon)"). So, the U-Boot's syscon works differently
from the beginning. I'd say this is mis-implementation given that
DT is not oriented to a particular project, but Linux is the canon
of DT in practice.
The problem typically arises in the combination of "syscon" and
"simple-mfd" compatibles.
In Linux, they are orthogonal, i.e., the order between "syscon" and
"simple-mfd" does not matter at all.
Assume the following compatible.
compatible = "foo,bar-syscon", "syscon", "simple-mfd";
In U-Boot, this device node is bound to the syscon driver
(driver/core/syscon-uclass.c) since the "syscon" is found to be the
most compatible. Then, syscon_get_regmap() succeeds.
However,
compatible = "foo,bar-syscon", "simple-mfd", "syscon";
does not work because this node is bound to the simple-bus driver
(drivers/core/simple-bus.c) in favor of "simple-mfd" compatible.
The compatible string "syscon" is just dismissed.
Moreover,
compatible = "foo,bar-syscon", "syscon";
works like the first case because the syscon driver populates the
child devices. This is wrong because populating children is the job
of "simple-mfd" (or "simple-bus").
This commit ports syscon_node_to_regmap() from Linux. This API
does not require the given node to be bound to a driver in any way.
Reported-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, regmap_init_mem() takes a udevice. This requires the node
has already been associated with a device. It prevents syscon/regmap
from behaving like those in Linux.
Change the first argumenet to take a device node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
device_is_compatible() takes udevice, but there is no such a helper
that takes ofnode.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function is no more used, and replaced by psci_save
which save also context id as requested by PSCI requirements.
Even if the context id is not used by Linux, it should be saved
and restored in r0 when the CPU_ON is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Replace the psci_save_target_pc call by the new function
psci_save(cpu, pc,context_id)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add PSCI v1.0 support for Linux and manage PSCI state
for each CPU (affinity 0 level) with all mandatory functions:
- PSCI_VERSION
- CPU_SUSPEND
- CPU_OFF
- CPU_ON
- AFFINITY_INFO
- SYSTEM_OFF
- SYSTEM_RESET
- PSCI_FEATURES
and 1 optional to avoid Linux warning
- MIGRATE_INFO_TYPE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: CITOOLS <smet-aci-reviews@lists.codex.cro.st.com>
The added function psci_arch_cpu_entry() is called
during psci_cpu_entry() and can be used by arch to handle
PSCI state transition from ON_PENDING to ON.
The default weak function is empty: not behavior change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save and use the 3rd parameter of PSCI CPU_ON request: context_id.
The context_id parameter is only meaningful to the caller.
U-Boot PSCI preserves a copy of the value passed in this parameter.
Following wakeup from a powerdown state, U-BOOT PSCI places
this value in R0 when it first enters the OS.
NB: this context id is not (yet?) used by Linux but it is mandatory
to be PSCI compliant.
update armv7 psci functions:
- psci_save_target_pc(): keep for backward compatibility with
current platform (only save PC and force context id to 0)
=> should be removed when all platform migrate to the new API
- psci_save(): new API to use by ARMv7 platform with PSCI,
save pc (= entry_point_address) and context_id
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- Based on commit 08ae21af96 ("MAINTAINERS: Switch nxp.com domain")
update or drop some formerly Freescale addresses.
- Update a few aliases to reflect current custodians
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Banana Pi BPI-M2 Berry is a quad-core mini single board computer
built with Allwinner V40 SoC. It features
- Quad Core ARM Cortex A7 CPU V40
- 1GB of RAM .
- microSD/SATA port..
- onboard WiFi and BT
- 4 USB A 2.0 ports
- 1 USB OTG port
- 1 HDMI port
- 1 audio jack
- DC power port
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
omap-common cache enabling sequence relies on cpu_init_cp15()
(inside start.S) for enabling I-caches. But cpu_init_cp15()
can be skipped if CONFIG_SKIP_LOWLEVEL_INIT is defined. So
enable I-caches if not enabled already.
Debugged-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Building with verified boot support requires hash, add that
dependency here. Otherwise the following build error will come out
without crc command.
LD u-boot
lib/built-in.o: In function `hash_calculate':
lib/rsa/rsa-checksum.c:29: undefined reference to
`hash_progressive_lookup_algo'
...
make[1]: *** [u-boot] Error 1
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
A common voltage of 1.35V was being programmed for all am43 board
versions. EPOS-EVM Needs 1.20V for LPDDR2.
Fixes: fc69d47262 (“board: ti: AM43XX: Add ddr voltage rail configuration”)
Reported-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With tighter build flags the fact that <stdio_dev.h> doesn't have a
reference back to MAX_NAMES causes an error. Include <stdio.h> here and
then in common/console.c use MAX_NAMES rather than 3 when working with
stdio_names.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
With tighter build flags the fact that this header referenced
uchar/ushort without including what typedefs it causes an error. Rather
than add another include here, drop the section in question as it is
unused.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The DEBUG macro is never defined unless explicitly enabled.
Drop useless #undef DEBUG in the board configs so it won't
spread any further.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull the symbol from the boards and zap struct rmobile_sysinfo as they
are rather useless. The entire purpose of that whole machinery was to
print board name in the CONFIG_ARCH_RMOBILE_BOARD_STRING. Do that in a
far simpler and more contained manner.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename CONFIG_RMOBILE_BOARD_STRING to CONFIG_ARCH_RMOBILE_BOARD_STRING
to make things consistent, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Synchronize the README with the current state of U-Boot, unify
the build instructions to avoid duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
freescale.com domain is no longer reachable, so switch the
maintainers' emails to nxp.com domain instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The 'SDHCI_QUIRK_NO_HISPD_BIT' is used wrong here. The purpose of this
quirk is to tell the sdhci-driver that the IP-core doesn't have a "high-
speed-enable" bit in its registers.
With this commit we change this to the correct quirk:
SDHCI_QUIRK_BROKEN_HISPD_MODE
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Some IP-core implementations of the SDHCI have different troubles on the
silicon where they are placed.
On ZYNQ platform for example Xilinx doesn't accept the hold timing of an
eMMC chip which operates in High-Speed mode and must be forced to
operate in non high-speed mode. To get rid of this
"SDHCI_QUIRK_BROKEN_HISPD_MODE" is introduced.
For more details about this refer to the Xilinx answer-recor #59999https://www.xilinx.com/support/answers/59999.html
This commit:
- doesn't set HISPD bit on the host-conroller
- reflects this fact within the host-controller capabilities
Upon this the layer above (mmc-driver) can setup the card correctly.
Otherwise the MMC card will be switched into high-speed mode and causes
possible timing violation on the host-controller side.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
sd_read_ssr returns 0, means no error.
Fixes: 5b2e72f32721484("mmc: read ssr only if MMC write support is enabled")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Exynos5422 board has s2mps11 pmic.
If CONFIG_PMIC_S2MPS11 is enabled, it can initialize PMIC and Regulators
during booting time.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
The dts Makefile entries for the H3 are not ordered correctly.
Move the Nano Pi entries before the Orange Pi so they are.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H5 version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H5 SoC, and
has 4Gb DDR3 chips instead of 2Gb ones.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds a device tree file for the H2+ version of the Libre
Computer Board ALL-H3-CC. It is the same board first introduced in
commit afe2754412 ("sunxi: Add support for Libre Computer Board
ALL-H3-CC H3 ver."), with the H3 SoC replaced with the H2+ SoC, and
has only two 2Gb DDR3 chips instead of four.
The device tree utilizes the common board design file for ALL-H3-CC,
providing just the model strings and SoC specifics.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Libre Computer Project ALL-H3-CC has three models, all using the
same board design, but with different pin compatible SoCs and amount of
DRAM.
Currently only the H3 1GB DRAM variant is supported. To support the two
other variants, first split the original device tree into a common board
design part and an SoC specific part.
The SoC part only defines which SoC is used and model name, and includes
the SoC specific dtsi file and the common design dtsi file.
Also fix up the SPDX identifier line to use the correct comment style,
and place it on the first line.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Libre Computer Board ALL-H3-CC does not have an I2C controllable
regulator. Having R_I2C and SPL_I2C enabled serves no purpose.
Disable them.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
If generating a script image and no datafile has been passed in, mkimage
dies with SIGSEGV:
#0 __strchr_sse2 () at ../sysdeps/x86_64/multiarch/../strchr.S:32
#1 0x0000000000403818 in main
at tools/mkimage.c:503
Add explicit test for datafile to fix this.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
The size of 'filebuf' was not increased as more and more bytes are read
from stdin, but 'filebuf' was always reallocated to the same fix size.
This works as long as only less bytes than the initial buffer size come
in, for more input this will segfault. (It actually does, I tested
that.) So for each loop cycle the buffer size has to be increased by the
number of bytes we want to read.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
On success read() returns the number of bytes read or zero for EOF. On
error -1 is returned and errno is set, so the right way to test if read
had failed is to test the return value instead of errno.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Uart status register is named USART_ISR on STM32F7, STM32H7
and STM32MP1 SoCs family, but USART_SR only on STM32F4 SoCs.
Use USART_ISR_ prefix instead of USART_SR_ .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable uart overrun feature which allows to benefits of uart
FIFO usage.
Previously overrun management was disabled, this has to effect
to bypassed the uart FIFO usage even if FIFO was enabled.
In particular configuration, for example when video console is
enabled, copy/pasting a long command line in console results in
corruption. This is due to the fact that a lot of time is consumed
in flushing the cache during frame buffer update, so uart chars are
not read fast enough.
By using uart FIFO and managing overrun, long command line can by
copy/paste in console without being corrupted.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
If SPL serial support is disabled nothing brings in sprintf, snprintf
or simple_strtoul:
env/built-in.o: In function `regex_callback':
env/attr.c:128: undefined reference to `sprintf'
disk/built-in.o: In function `blk_get_device_by_str':
disk/part.c:386: undefined reference to `simple_strtoul'
disk/part.c:395: undefined reference to `simple_strtoul'
disk/built-in.o: In function `blk_get_device_part_str':
disk/part.c:522: undefined reference to `simple_strtoul'
disk/built-in.o: In function `part_set_generic_name':
disk/part.c:704: undefined reference to `sprintf'
drivers/built-in.o: In function `init_peripheral_ep':
drivers/usb/musb-new/musb_gadget.c:1826: undefined reference to `sprintf'
drivers/built-in.o: In function `musb_core_init':
drivers/usb/musb-new/musb_core.c:1451: undefined reference to `snprintf'
Add those dependencies here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
When SPL serial is disabled, callers who need sprintf or strtoul fail
because their inclusion is guarded by CONFIG_SPL_SERIAL_SUPPORT/
CONFIG_TPL_SERIAL_SUPPORT.
Split printf, sprintf and strto into their own entries and then select
all of them if SERIAL_SUPPORT is enabled to match the current behaviour.
Include panic.o unconditionally as it can be called from anywhere which
uses BUG_ON().
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
If CONFIG_SPL_SERIAL_SUPPORT is not set, then the build will fail:
board/ti/am335x/built-in.o: In function `spl_start_uboot':
board/ti/am335x/board.c:247: undefined reference to `serial_tstc'
board/ti/am335x/board.c:247: undefined reference to `serial_getc'
Avoid the calls to the serial functions in that case.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
CONFIG_SPL_SERIAL_SUPPORT had already been migrated to Kconfig, but
existed in some include files; fix those up here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
If CONFIG_SPL_SERIAL_SUPPORT is disabled then the build fails because
serial_init is undefined. Guard preloader_console_init() appropriately
to fix this.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
SYS_ARCH_TIMER guards the usage of the ARM Generic Timer (aka arch
timer) in U-Boot.
At the moment it is mandatory for ARMv8 and used by a few ARMv7 boards.
Add a proper Kconfig symbol to express this dependency properly,
allowing certain board configuration to later disable arch timer in case
there are any problems with it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[tuomas: rebase + fix conflicts and resync with moveconfig & use select]
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
After commit 46fc679ede ("arm: timer: get frequency for arch timer
armv7 in cp15 cntfrq") the ARM architected timer driver knows how to
determine the timer frequency at runtime by reading the CNTFRQ register,
so we don't need to hardcode the timer frequency anymore.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
'env exists' is used for scripting in include/config_distro_bootcmd.h
This command is available only when CONFIG_CMD_ENV_EXISTS is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
RSA_SOFTWARE_EXP and RSA_FREESCALE_EXP are wrapped inside:
if RSA
...
endif
So, remove the redundant "depends on RSA" from their depends expression.
In addition, move SPL_RSA into the same "if RSA ... endif" block, since
its only direct dependeny is CONFIG_RSA. This tidies up and simplifies
reading of lib/rsa/Kconfig.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_CMD_LOG without CONFIG_LOG leads to a build error:
‘gd_t {aka volatile struct global_data}’ has no member named
‘default_log_level’
So CMD_LOG should select LOG.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Compling with CONFIG_LOG and without CONFIG_DM results in
common/log.c:47: undefined reference to `uclass_get_name'
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The __FILE__ macro is used everywhere in U-Boot to locate the file
printing the log message, such as WARN_ON(), etc. If U-Boot is
built out of tree, this can be a long absolute path.
This is because Kbuild runs in the objtree instead of the srctree,
then __FILE__ is expanded to a file path prefixed with $(srctree)/.
A brand-new option from GCC, -fmacro-prefix-map, solves this problem.
If your compiler supports it, __FILE__ is the relative path from the
srctree regardless of O= option. This provides more readable log,
more reproducible builds, and smaller image size.
[ Linux commit: a73619a845d5625079cc1b3b820f44c899618388 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These symbols are declared in Kconfig, so it's wrong to set them in
header files.
Note that this is not size-neutral - some 'default y' options will now
get turned on by Kconfig, such as CONFIG_CMD_DM=y and CONFIG_DM_STDIO=y.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
As of clang-5.0, things have changed a bit. First, we cannot
automatically guess -target values as if we do not pass one with CC then
cc-option will fail. Second, to disable movt/movw relocations the
argument has become -mno-movt.
Related to the target part, we cannot use arm-none-eabi as that ends up
being too generic of an ARM target for things like say rpi_3_32b to
work.
Signed-off-by: Tom Rini <trini@konsulko.com>
Re-sync the logic about which clang warnings to disable from v4.17-rc1.
Note that we don't disable all of the same ones as for now we haven't
run into any cases of warnings from clang in code from upstream Linux.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This allows using the full SPL framework on mxs devices. In this
mode, the u-boot.sb image loaded by the boot ROM contains only the
SPL which then loads U-Boot proper or a kernel in falcon mode.
Signed-off-by: Mans Rullgard <mans@mansr.com>
With full SPL enabled, the loaded image overwrites the mxs_spl_data
location. Moving it a slightly lower address fixes this.
Signed-off-by: Mans Rullgard <mans@mansr.com>
When building in Thumb mode, the linker might generate mode switching
stubs in .glue sections. Include these in the final link.
Signed-off-by: Mans Rullgard <mans@mansr.com>
The code attempts to preserve the value of LR by storing it in R12/IP
across the lowevel_init() call. However, this register is not saved
by the callee. Use a register that guaranteed to be preserved instead.
Signed-off-by: Mans Rullgard <mans@mansr.com>
With the full SPL framework enabled, lowlevel_init() is required.
Make the empty stub weak so boards can override it.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Commit 2baa997240 ("arm: socfpga: Add FPGA driver support for Arria 10")
Polling on wrong cleared bit. Fix with correct polling on bit is set.
Fixes: 2baa997240 ("arm: socfpga: Add FPGA driver support for Arria 10")
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
In case usb configuration is unknown (cdev->config == NULL), non standard
request should not be processed.
Remove also the cdev->config check below which will never happen.
This issue was seen using ums feature.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When no PHYs are declared in the dwc3 node, the phy init fails.
This patch checks if the "phys" property is presend and reports
the error returned by dev_count_phandle_with_args().
This patchs also fixes the styles issues added in last commit.
This patch should fix the DWC3 support on the UniPhier SoC family.
Fixes: 7c839ea70c ("usb: host: dwc3: Add support for multiple PHYs")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The E2 Alt port was broken since some time. This patch updates
the E2 Alt port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The M2-N Gose port was broken since some time. This patch updates
the M2-N Gose port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Lager port was broken since some time. This patch updates
the H2 Lager port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch removes warp7_secure_defconfig. A previous patch set
CONFIG_ARMV7_BOOT_SEC_DEFAULT=y on the unsecure WaRP7 config. Fabio asked
if I could confirm that the NXP and upstream kernels will boot on the WaRP7
with CONFIG_ARMV7_BOOT_SEC_DEFAULT=y. I can confirm that this is the case,
so there's no need to support the secure defconfig - drop it now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Without this commit we do have an explicit dependency on CONFIG_PHYLIB
when one wants to set PHY ADDR on a iMX board (FEC + driver model).
This shall be changed to CONFIG_FEC_MXC_PHYADDR, as only when we do have
it set, we shall mask out other devices.
As a side effect, when CONFIG_FEC_MXC_PHYADDR is not set, we scan PHY bus
for connected PHY devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This reverts commit b5b0e4e351.
Commit f916757300 ("imx: Create distinct pre-processed mkimage
config files") provided a proper fix for the parallel mkimage
config files build failure, so the original workaround can be
safely reverted now.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel
that has CAAM support and needs to boot in secure mode.
Instead of keeping two different config targets for the same board,
remove mx7dsabresd_secure_defconfig and select
CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that
this target could be used to boot both mainline and the vendor kernel.
This makes maintenance task easier and avoid potentially confusion
for the end user.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch adds support for verifying a signed boot.scr. With this in place
it's possible for run-time Linux to update boot.scr to set different
variables such as switching between different boot partitions, pointing to
different kernels etc and for u-boot to verify these changes via the HAB
prior to executing the commands contained in boot.scr.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
setexpr allows us to do arithmetic for env variables - something that is
both useful and required when doing HAB authentication without hard-coding
HAB load addresses.
This patch enables CMD_SETEXPR for the WaRP7 defconfig.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch introduces the environment variable ivt_offset. When we define a
load address for Linux or DTB or any file the IVT associated with that file
is prepended. We extract the actual load addresses from u-boot.cfg and feed
these values into the code-signing process - hence we want u-boot to have
the real load addresses exported in uboot.cfg.
ivt_offset represents the addition or subtraction from the load address
that must happen to find an IVT header.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Doing secure boot on the WaRP7 using a common image format and the same
variable to represent the base address for each call means we can reduce
down the command to a single environment command.
This patch adds warp7_auth_or_fail as a wrapper around
"hab_auth_img_or_fail ${hab_ivt_addr} ${filesize} 0".
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We need to know the name of a signed boot-script, its better to have a
separate variable for this then to simply append some fixed string to an
existing image name.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Assigning the UUID discovery path to a tweakable environment variable means
that later steps in the boot process - particularly a boot script can
change the target root partition of a particular Linux boot.
Retargeting the rootfs is an important feature when doing ping/pong
upgrades allowing a boot script to select ping or pong as necessary without
reprogramming the bootloader.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Adding CONFIG_WARP7_ROOT_PART allows a defconfig to specify which partition
is use as the root partition on WaRP7, this is a desirable change in order
to support a different partitioning schemes. The default is the current
partition #2.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to sign images with the IMX code-signing-tool (CST) we need to
know the load address of a given image. The best way to derive this load
address is to make it into a define - so that u-boot.cfg contains the
address - which we can then parse when generating the IMX CST headers.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch enables CONFIG_BOOTM_TEE. Once enabled its possible to
chain-load Linux through OPTEE.
Loading kernel to 0x80800000
=> run loadimage
Load FDT to 0x83000000
=> run loadfdt
Load OPTEE to 0x84000000
=> fatload mmc 0:5 0x84000000 /lib/firmware/uTee.optee
Then chain-load to the kernel via OPTEE
=> bootm 0x84000000 - 0x83000000
Image Name:
Image Type: ARM Trusted Execution Environment Kernel Image (uncompressed)
Data Size: 249844 Bytes = 244 KiB
Load Address: 9dffffe4
Entry Point: 9e000000
Verifying Checksum ... OK
Loading Kernel Image ... OK
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Various function associated with booting the WaRP7 in High Assurance Boot
(HAB) mode are enabled by switching on CONFIG_SECURE_BOOT.
This patch enables CONFIG_SECURE_BOOT for the WaRP7 defconfig.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to sign images with the IMX code-signing-tool (CST) we need to
know the load address of a given image. The best way to derive this load
address is to make it into a define - so that u-boot.cfg contains the
address - which we can then parse when generating the IMX CST headers.
This patch makes the OPTEE_LOAD_ADDR available via u-boot.cfg for further
parsing by external tools.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Right now a region of 0x300000 bytes is allocated at the end of DRAM for
the purposes of loading an OPTEE firmware inside of it. This patch adds the
printout of the relevant address ranges.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Subtracts CONFIG_OPTEE_TZDRAM_SIZE from the available DRAM size.
On WaRP7 we simply define the OPTEE region as from the maximum DRAM address
minus CONFIG_OPTEE_TZDRAM_SIZE bytes.
Note the OPTEE boot process will itself subtract the DRAM region it lives
in from the memory map passed to Linux.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch adds an environment variable called "hab_enabled" which gets set
to a boolean status indicating whether HAB is enabled or not.
Subsequent patches can use this environment variable to determine if its
necessary to run a given binary through the hab_auth_img console command.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to correctly produce an image with a IVT/DCD header we need to
define a CSF in imximage.cfg. We just use the mx7 default here.
All we have to do with this option switched on is "make u-boot.imx" and we
then will get
- u-boot.imx
- u-boot.imx.log
The log file is really important because it gives the addresses for the HAB
that we will require to sign the u-boot image using the CST. Since the
addresses can change this logfile is a critical output.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch adds BOOTROM_IVT_HDR_OFFSET at 0xC00. The BootROM expects to
find the IVT header at a particular offset in an i.MX image.
Defining the expected offset of the IVT header in the first-stage BootROM
image format is of use of later stage authentication routines where those
routines continue to follow the first-stage authentication layout.
This patch defines the first stage offset which later patch make use of.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
commit 8519c9c98a ("tools/imximage: use 0x prefix in HAB Blocks line")
adds an 0x prefix to each HAB Block number to make it easier for host tools
to process the HAB Block output, however it neglects to apply the same
prefix to the DCD Blocks directive. You need the DCD Blocks directive if
you are making a u-boot recovery image which the BootROM will accept via
the USB upload utility.
This disparity results in a fruity output like this with HAB Blocks
prefixed but DCD Blocks not prefixed - which is pretty inconsistent.
This patch fixes the difference assuming the original commit was a
legitimate change.
Old:
Image Type: Freescale IMX Boot Image
Image Ver: 2 (i.MX53/6/7 compatible)
Mode: DCD
Data Size: 430080 Bytes = 420.00 KiB = 0.41 MiB
Load Address: 877ff420
Entry Point: 87800000
HAB Blocks: 0x877ff400 0x00000000 0x00066c00
DCD Blocks: 00910000 0000002c 000001d4
New:
Image Type: Freescale IMX Boot Image
Image Ver: 2 (i.MX53/6/7 compatible)
Mode: DCD
Data Size: 430080 Bytes = 420.00 KiB = 0.41 MiB
Load Address: 877ff420
Entry Point: 87800000
HAB Blocks: 0x877ff400 0x00000000 0x00066c00
DCD Blocks: 0x00910000 0x0000002c 0x000001d4
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dts node for timer3.
Because of the rockchip timer can only KNOWN "dtd_rockchip_rk3368_timer"
with OF_PLATDATA enable, so we override its compatible to
"rockchip,rk3368-timer".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The DM driver for ockchip timer blocks is also applicable to the
RK3188 and RK3288 timer blocks: add 'rockchip,rk3188-timer' and
'rockchip,rk3288-timer' to its compatible list to support devices
claiming compatibility with these.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.
This implements a minimal clk_enable for the RK3288 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Throughput tests have shown the sunxi_mmc driver to take over 10s to
read 10MB from a fast eMMC device due to excessive delays in polling
loops.
This commit restructures the main polling loops to use get_timer(...)
to determine whether a (millisecond) timeout has expired. We choose
not to use the wait_bit function, as we don't need interruptability
with ctrl-c and have at least one case where two bits (one for an
error condition and another one for completion) need to be read and
using wait_bit would have not added to the clarity.
The observed speedup in testing on a A31 is greater than 10x (e.g. a
10MB write decreases from 9.302s to 0.884s).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With clang-4.0 and later we see:
warning: logical not is only applied to the left hand side of this bitwise
operator [-Wlogical-not-parentheses]
if ((!gd->flags & GD_FLG_RELOC))
^ ~
And while the compiler suggests adding parenthesis around gd->flags, a
reading of the code says that we want to know when GD_FLG_RELOC is not
set and then return.
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Patch queue for efi - 2018-04-23
Some last minute fixes for 2018.05. Most of them are minor fixes. On
top we have some functional improvements for the device path logic
which should also help us be more compatible.
Provide unit tests for the EFI_DEVICE_PATH_UTILITIES_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The missing services of the EFI_DEVICE_PATH_UTILITIES_PROTOCOL are
implemented.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Device paths may consist of multiple instances. Up to now we have only
considered the size of the first instance. For the services of the
EFI_DEVICE_PATH_UTILITIES_PROTOCOL in most cases the total length of the
device path is relevant.
So let's rename efi_dp_size() to efi_dp_instance_size() and create a new
function efi_dp_size() that calculates the total device path length.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_dp_size() is meant to return the device path length without the end
node.
The length of a device path containing only an end node was incorrectly
reported as 4.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The logic of the AppendDevicePath service of the
EFI_DEVICE_PATH_UTILITIES_PROTOCOL is incorrectly implemented:
* if both paths are NULL an end node has to be returned
* if both paths are not NULL the end node of the second device path has to
be kept
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the CreateDeviceNode service of the device path utility protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Executing a test after failed setup may lead to unexpected behavior like
an illegal memory access. So after a setup failure we should skip to
teardown.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We do not support bootefi booting ARMv7 in non-secure mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
According to the documentation the EFI log category is called LOGC_EFI.
All other categories start with LOGC_. So let's fix it.
Fixes: 1973b381a1 ("log: add category LOGC_EFI")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently, the address region, 0xf8000 - 0x100000, is used for SPL
stack for the 32bit SoCs. Because the U-Boot proper image starts
from 0x70000, the maximum size of the U-Boot proper image is 544KB
(0x70000 - 0xf8000) for the NOR boot mode. Now uniphier_v7_defconfig
is almost hitting this size limit. Changing CONFIG_SPL_STACK can
raise the size limit with less impact. With this, the size limit
will increase to 576KB (0x70000 - 0x100000). If we need to increase
it even more, we would be able to change CONFIG_SYS_UBOOT_BASE at the
cost of the flashing command changes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Some boards support an SD card and an eMMC device at the same time.
Since both belong to 'mmc', they are identified by a device number.
When the device number of the eMMC is 1 instead 0, "mmc dev" command
must be performed to switch the target device before flashing images.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The last clock consumer in SPL, SD/eMMC driver, gave up using the
clock driver. The clock driver is only used in U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that the SD/eMMC driver does not use the clock driver in SPL,
remove u-boot,dm-pre-reloc properties to let the fdtgrep tool drop
the unnecessary nodes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The size of SPL is hitting the limit (64KB) for uniphier_v7_defconfig.
When booting from SD/eMMC, obviously its clock has been properly set up
by the boot ROM. Acutually, no need to re-initialize the clock in SPL.
Using a clock driver would generalize the SoC specific code, but
solving the memory footprint problem would win.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I need to differentiate the clock handling for uniphier-sd. Move it
to each driver's probe function from the tmio common code so that
renesas-sdhi will not be affected.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the recent changes, the size of the U-Boot proper image for
uniphier_v7_defconfig exceeded the current limit, 512KB, then SPL
fails to load the whole of the U-Boot proper. Increase the size.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In case of error in soc_clk_dump function are returned different values
then CMD return values (-1, 0, 1).
For example:
ZynqMP> clk dump
exit not allowed from main input shel
The patch is checking all negative return values and return
CMD_RET_FAILURE which is proper reaction for these cases.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Boards have an option to rewrite variable locations in their own board
files. This is necessary for qspi and nand configurations where boot
image can be bigger then 896k(current limit).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When static memory configuration is used U-Boot has capability to detect
memory size in setup range. Enable this feature for static
configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no need to use zynq name as SYS_BOARD for all boards.
The patch is adding an option to change it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_NAND_ZYNQ selects CONFIG_SYS_NAND_SELF_INIT, so the
driver doesn't have to play any ifdef game.
Also, we can mark zynq_nand_init() as static and get rid
of the mach-specific nand.h header.
This is really a revert of:
"mtd: zynq: nand: Move board_nand_init() function to board.c"
(sha1: 310995d9f9)
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This driver is currently broken, refusing to initialize properly.
The reason is that get_nand_dev_by_index() was being called before
nand_register(), thus returning a pointer into uninitialized memory.
In other words, the struct mtd_info used by the driver is total junk.
Fix it by getting the correct struct mtd_info, via nand_to_mtd()
on the driver's struct nand_chip.
Tested on a custom board, where the CPU is halted without this patch.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-boot driver for sunxi-mmc uses PLL6, unlike linux kernel where
PLL5 is used, with clock rates respectively 600MHz and 768MHz.
Thus there are different phase degree steps - 24 for the kernel and
30 for u-boot.
In the kernel driver the phase is set 90 deg for output and 120 for
sample. Dividing by 30 will result values 3 and 4. Those are the
values set in the u-boot driver.
However, the condition defining delays is wrong. MMC core driver
requests clock of 52MHz, sunxi-driver sets clock of 50MHz, but
phase is set 30 deg for output and 120 deg for sample.
Apparently this works for most cards.
On A20-SOM204-EVB-eMMC there is eMMC card (KLMAG2GEND) which complains
about it. Maybe there is other boards with similar problem?
So the fix is to match delays for both u-boot and kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
While switching to readl_poll_timeout macros from custom code
the waiting condition was accidently inverted, so it was pure
luck that this code works at least in some conditions.
Fix that by inverting exit condition for readl_poll_timeout.
Fixes: c6b4f031d9 ("DW SPI: fix tx data loss on FIFO flush")
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The disabled clk API returns -ENOSYS unlike the reset API returning -ENOTSUPP.
Fixes: ca7fdc8b12 ("usb: host: Add simple of glue driver for DWC3 USB Controllers integration")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The E2 Silk port was broken since some time. This patch updates
the E2 Silk port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The port is missing support for I2C1 for DA9063 reset, since the
I2C driver needs to be converted to DM and DT probing. That's not
an issue for this patch though, since the reset was broken on Silk
since forever.
Add MMC DM and DT probing support into the SH MMCIF driver.
This patch abstracts out the common bits of the send command
and set ios functions, so they can be used both by DM and non
DM setups and adds the DM probe support.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The initconst is not used in U-Boot, drop it. The r8a7794_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The initconst is not used in U-Boot, drop it. The r8a7792_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This commit adds support for the SST sst26wf016, sst26wf032
and sst26wf064 flash IC.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
sst26wf flash series block protection implementation differs
from other SST series, so add specific implementation
flash_lock/flash_unlock/flash_is_locked functions for sst26wf
flash ICs.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Subtle ARC fixes for v2018.05-RC3
These are only very subtle clean-ups here and there including:
* Correctly specified CPU freq for HSDK
(production boards are all shipped with 500MHZ as opposed
to early batch running at 1GHz)
* Addition of SNPS internal group email to MAINTAINERS file
* Switch to Hush shell on AXS10x boards
In the commit "reset: Add get/assert/deassert/release for bulk of reset signals"
the disabled reset_release_bulk() and reset_get_bulk() used the wrong
struct clk_bulk instead of struct reset_ctl_bulk.
Fixes: 0c28233903 ("reset: Add get/assert/deassert/release for bulk of reset signals")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit b4d956f6bc ("bootm: Align cache flush end address correctly")
aligns the end address of the cache flush operation to a cache-line size to
ensure lower-layers in the code accept the range provided and flush.
A similar action should be taken for the begin address of a cache flush
operation. The load address may not be aligned to a cache-line boundary, so
ensure the passed address is aligned.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reported-by: Breno Matheus Lima <brenomatheus@gmail.com>
Suggested-by: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This fixes the Coverity Defect CID 175347 when dev_count_phandle_with_args()
returns a negative value.
Fixes: a855be87da ("clk: Add get/enable/disable/release for a bulk of clocks")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This fixes the Coverity Defect CID 175348 when dev_count_phandle_with_args()
returns a negative value.
Fixes: 0c28233903 ("reset: Add get/assert/deassert/release for bulk of reset signals")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The M2 Koelsch port was broken since some time. This patch updates
the M2 Koelsch port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
"Global data" structure "gd" is not used in init_helpers.c
thus DECLARE_GLOBAL_DATA_PTR might be safely removed.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
CPU on HSDK board runs at 500MHz after preloader so fix
wrong CPU frequency value in hsdk_defconfig.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
None of the SoCFPGA platforms will support EFI/ISO partition types that
is needed for DISTRO_DEFAULTS. SoCFPGA bootroom will only support 0xa2
partition type.
This is needed to help limit the size of the SPL to within the 64k limit
that is required for SoCFPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add code to look for a reset manager property. Specifically, look for the
reset-names of 'i2c'. A reset property is an optional feature, so only print
out a warning and do not fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus bringing the
IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add all the appropriate i2c alias in the base socfpga dtsi and enables
the i2c node on the DE0 NANO board.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the RPC QSPI driver on R8A77970 V3M Eagle and configure
the environment layout to match that used by old U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mv_sdhci driver was not zeroing the sdhci_host structure it
allocates causing random access violations in parts of the mmc core
where the "ops" member pointers are checked and called if not NULL.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The line "-obj-$(CONFIG_STM32_SERIAL) += serial_stm32.o"
is found twice in Makefile.
Fixes: ae74de0dfd ("serial: stm32: Rename serial_stm32x7.c to serial_stm32.c"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For CONFIG_ENV_FAT_INTERFACE != 'mmc' a link error
env/fat.c:93: undefined reference to `mmc_initialize'
occurs if CONFIG_MMC_SUPPORT is not enabled.
Fixes: 26862b4a40 ("env: mmc/fat/ext4: make sure that the MMC sub-system
is initialized before using it")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Relocate env drivers if manual relocation is enabled. This
patch fixes the issue of u-boot hang incase if env is
present in any of the flash devices.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 8e14ba7bd5 ("gpio: omap_gpio: Add DM_FLAG_PRE_RELOC
flag") omap GPIO gets bound before relocation. Unfortunately due to
this, on at least the beaglebone black, the pre-relocation memory pool
gets exhausted before probing the serial port. This then causes u-boot
to panic as CONFIG_REQUIRE_SERIAL_CONSOLE is set...
Resolve this by resizing the default size of the pre-relocation malloc
pool for AM335X platforms.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
We enabled CONFIG_ISO_PARTITION by default for distro boot, so that U-Boot
could load distro images that usually get shipped as iso images. These images
usually come with a board agnostic boot environment.
However, there is very little point in having ISO support enabled (for anyone
really) in SPL, as the whole idea of SPL is to load U-Boot proper which again
is board specific. So the fact that we enable ISO support in U-Boot proper does
not mean at all that we want ISO support in U-Boot SPL.
Hence, let's remove the Kconfig dependency. Along the way, let's also clean up
all those default configs that disabled SPL ISO support.
Signed-off-by: Alexander Graf <agraf@suse.de>
We only use coreboot as a target on x86 platforms, since on ARM platforms
U-Boot always runs as the primary boot loader. Rename the coreboot-x86
platform to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This updates the doc of booting VxWorks, like loading an x64 kernel,
and how to make VxWorks graphics console driver work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
On VxWorks x86 its bootline address is at a pre-defined offset @
0x1200. If 'bootaddr' is not passed via environment variable, we
assign its value based on the kernel memory base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There is a small duplication in do_bootvx() that does the bootline
copy. Refactor this a little bit to make it simpler.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When booting from EFI BIOS, VxWorks bootloader stores the EFI GOP
framebuffer info at a pre-defined offset @ 0x6100. When VxWorks
kernel boots up, its EFI console driver tries to find such a block
and if the signature matches, the framebuffer information will be
used to initialize the driver.
However it is not necessary to prepare an EFI environment for
VxWorks's EFI console driver to function (eg: EFI loader in
U-Boot). If U-Boot has already initialized the graphics card and
set it to a VESA mode that is compatible with EFI GOP, we can
simply prepare such a block for VxWorks.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If video initialization fails, the "Video:" output message will be
mixed with the next console log. Change to print out such message
only when everything is OK, which improves the boot log readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This changes some boards' default FRAMEBUFFER_VESA_MODE to use 32-bit
pixel format for better VxWorks compatibility.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This changes the default FRAMEBUFFER_VESA_MODE to use 32-bit pixel
format for better VxWorks compatibility.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_FRAMEBUFFER_SET_VESA_MODE is not set, don't switch
graphics card to VESA mode. This applies to both native mode
and emulator mode of running the VGA BIOS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a very simple ELF64 loader via program headers, similar
to load_elf_image_phdr() that we already have.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds ELF header, program header and section header structure
defines for the 64-bit ELF image.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix various style violations in elf.h
- use correct comment format if the comment fits in just one line
- remove the ending period for the one-line comment
- use tab for the indention instead of space
- put the opening brace at the same line of a typedef/union
- remove <name> in a 'typedef struct' for consistency
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This changes 'struct e820entry' to 'struct e820_entry' to conform
with the coding style.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This fixes the following checkpatch warning:
warning: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This changes 'struct e820info' to 'struct e820_info' to conform
with the coding style.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
VxWorks bootloader stores its size at a pre-defined offset @ 0x5004.
Later when VxWorks kernel boots up and system memory information is
retrieved from the E820 table, the bootloader size will be subtracted
from the total system memory size to calculate the size of available
memory for the OS.
Explicitly clear the bootloader image size otherwise if memory
at this offset happens to contain some garbage data, the final
available memory size for the kernel is insane.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present two environment variables 'e820data'/'e820info' are required
to boot a VxWorks x86 kernel, but this is superfluous. The offset of
these two tables are actually at a fixed offset from the kernel memory
base address and we can provide the kernel memory base address to U-Boot
via only one variable 'vx_phys_mem_base'.
Note as it name indicates, the physical address should be provided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The commit 3f70a6f577 ("x86: Add clr/setbits functions")
introduced the {read|write}_ macros to manipulate data.
Those macros are not used by any code in the u-boot project (despite the
io.h itself). Other architectures use io.h with {in|out}_* macros.
This commit brings some unification across u-boot supported architectures.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add readq() and writeq() definitions for x86.
Please note: in 32-bit code readq/writeq will generate two 32-bit
memory access instructions instead of one atomic 64-bit operation.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
These changes bring mainline back into line with the configurations
that were originally set in our stable BSP.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Each imx image is created by a separate sub-make and during this process
the mkimage config file is run though cpp.
The cpp output is to the same file no matter what imx image is being
created.
This means if two imx images are generated in parallel they will attempt
to independently produce the same pre-processed mkimage config file at
the same time.
Avoid the problem by making the pre-processed config file name unique
based on the imx image it will be used in. This way each image will
create a unique config file and they won't clobber each other when run
in parallel.
This should fixed the build bug referenced in b5b0e4e3 ("imximage:
Remove failure when no IVT offset is found").
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Working with HAB on the i.MX7 we've encountered a case where a board that
successfully authenticates u-boot when booting Linux via OPTEE subsequently
fails to properly bring up the RTC.
The RTC registers live in the low-power block of the Secure Non-Volatile
Storage (SNVS) block.
The root cause of the error has been traced to the HAB handing off the
SNVS-RTC in a state where HPCOMR::NPSWA_EN = 0 in other words where the
Non-Privileged Software Access Enable bit is zero. In ordinary
circumstances this is OK since we typically do not run in TZ mode, however
when we boot via HAB and enablng TrustZone, it is required to set
HPCOMR::NPSWA_EN = 1 in order for the upstream Linux driver to have
sufficient permissions to manipulate the SNVS-LP block.
On our reference board it is the difference between Linux doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000021 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000000 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x80002100 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: rtc core: registered
30370000.snvs:snvs-rtc-lp as rtc0
snvs_rtc 30370000.snvs:snvs-rtc-lp: setting system clock to2018-04-01 00:51:04 UTC (1522543864)
and doing this:
root@imx7s-warp-mbl:~# dmesg | grep rtc
snvs_rtc_enable read 0x00000000 from SNVS_LPLR @ 0x00000034
snvs_rtc_enable read 0x00000020 from SNVS_LPCR @ 0x00000038
snvs_rtc_enable read 0x00000001 from SNVS_HPLR @ 0x00000000
snvs_rtc_enable read 0x00002020 from SNVS_HPCOMR @ 0x00000004
snvs_rtc 30370000.snvs:snvs-rtc-lp: failed to enable rtc -110
snvs_rtc: probe of 30370000.snvs:snvs-rtc-lp failed with error -110
hctosys: unable to open rtc device (rtc0)
Note bit 1 of LPCR is not set in the second case and is set in the first
case and that bit 31 of HPCOMR is set in the second case but not in the
first.
Setting NPSWA_EN in HPCOMR allows us to boot through enabling TrustZone
and continue onto the kernel. The kernel then has the necessary permissions
to set LPCR::SRTC_ENV (RTC enable in the LP command register) whereas in
contrast - in the failing case the non-privileged kernel cannot do so.
This patch adds a simple init_snvs() call which sets the permission-bit
called from soc.c for the i.MX7. It may be possible, safe and desirable to
perform this on other i.MX processors but for now this is only tested on
i.MX7 as working.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
By using this file one can avoid cluttering <board>.h file with u-boot
HUSH commands necessary for booting target device.
With such approach the commands are stored only in one place and can be
reused if needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Enable display backlight only if a message needs to be displayed.
The kernel re-initializes the backlight, which results in some
unwanted artifacts.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
This patch adds hab_auth_img_or_fail() a command line function that
encapsulates a common usage of authenticate and failover, namely if
authenticate image fails, then drop to BootROM USB recovery mode.
For secure-boot systems, this type of locked down behavior is important to
ensure no unsigned images can be run.
It's possible to script this logic but, when done over and over again the
environment starts get very complex and repetitive, reducing that script
repetition down to a command line function makes sense.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
Subsequent patches will want to include imageimage.h but in doing so
include it on an assembly compile path causing a range of compile errors.
Fix the errors pre-emptively by encasing the majority of the declarations
in imximage.h inside an ifdef __ASSEMBLY__ block.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Breno Lima <breno.lima@nxp.com>
u-boot has a standard "serial#" environment variable that is suitable
for storing the iSerial number we will supply via the USB device
descriptor. serial# is automatically picked up by the disk subsystem in
u-boot - thus providing a handy unique identifier in /dev/disk/by-id as
detailed below.
Storing the hardware serial identifier in serial# means we can change the
serial# if we want before USB enumeration - thus making iSerial automatic
via OTP but overridable if necessary.
This patch reads the defined OTP fuse and sets environment variable
"serial#" to the value read.
With this patch in place the USB mass storage device will appear in
/dev/disk/by-id with a unique name based on the OTP value. For example
/dev/disk/by-id/usb-Linux_UMS_disk_0_WaRP7-0xf42400d3000001d4-0:0
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rui Miguel Silva <rui.silva@linaro.org>
Cc: Ryan Harkin <ryan.harkin@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The tester registers provide a unique chip-level identifier which
get_board_serial() returns in a "struct tag_serialnr".
This patch documents the properties of the registers; in summary.
31:0 OCOTP_TESTER0 (most significant)
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID
OCOTP_TESTER1 (least significant)
31:24
- The X-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
ID
23:16
- The Y-coordinate of the die location on the wafer/SJC CHALLENGE/ Unique
ID
15:11
- The wafer number of the wafer on which the device was fabricated/SJC
CHALLENGE/ Unique ID
10:0
- FSL-wide unique, encoded LOT ID STD II/SJC CHALLENGE/ Unique ID
The 64 bits of data generate a unique serial number per-chip.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently when we define CONFIG_SERIAL_TAG we will barf with a failure to
define "struct tag_serialnr".
This structure is defined in <asm/setup.h>, this patch includes
<asm/setup.h> to fix.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When the DDR calibration is enabled, a situation may happen that it
will fail on a few select boards out of a whole production lot. In
particular, after the first write leveling stage, the MPWLDECTRLx
registers will contain a value 0x1nn , for nn usually being 0x7f or
slightly lower.
What this means is that the HW write leveling detected that the DQS
rising edge on one or more bundles arrives slightly _after_ CLK and
therefore when the DDR DRAM samples CLK on the DQS rising edge, the
CLK signal is already high (cfr. AN4467 rev2 Figure 7 on page 18).
The HW write leveling then ends up adding almost an entire cycle (thus
the 0x17f) to the DQS delay, which indeed aligns it, but also triggers
subsequent calibration failure in DQS gating due to this massive offset.
There are two observations here:
- If the MPWLDECTRLx value is corrected from 0x17f to 0x0 , then the
DQS gating passes, the entire calibration passes as well and the
DRAM is perfectly stable even under massive load.
- When using the NXP DRAM calibrator for iMX6/7, the value 0x17f or so
in MPWLDECTRx register is not there, but it is replaced by 0x0 as one
would expect.
Someone from NXP finally explains why, quoting [1]:
"
Having said all that, the DDR Stress Test does something that we
do not advertise to the users. The Stress Test iself looks at the
values of the MPWLDECTRL0/1 fields before reporting results, and
if it sees any filed with a value greater than 200/256 delay
(reported as half-cycle = 0x1 and ABS_OFFSET > 0x48), the DDR
Stress test will reset the Write Leveling delay for this lane
to 0x000 and not report it in the log.
The reason that the DDR Stress test does this is because a delay
of more than 78% a clock cycle means that the DQS edge is arriving
within the JEDEC tolerence of 25% of the clock edge. In most cases,
DQS is arriving < 5% tCK of the SDCLK edge in the early case, and
it does not make sense to delay the DQS strobe almost a full clock
cycle and add extra latency to each Write burst just to make the
two edges align exactly. In this case, we are guilty of making a
decision for the customer without telling them we are doing it so
that we don't have to provide the above explanation to every customer.
They don't need to know it.
"
This patch adds the correction described above, that is if the MPWLDECTRx
value is over 0x148, the value is corrected back to 0x0.
[1] https://community.nxp.com/thread/456246
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The u-boot-ivt.img.log file contains 0x prefixes in the HAB Blocks line,
while the SPL.log does not. For consistency, and to make it easier to
extract and put into a .csf file for use with NXP's code signing tool,
add 0x prefixes here.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
The current makefile logic disables creation of the
SPL.log/u-boot-ivt.img.log etc. files when V=1 is given on the command
line, the rationale presumably being that the user wants and gets the
information on the console.
However, from general principles, I don't think a higher V= level
should affect which build artifacts get generated (and certainly
shouldn't produce fewer). Concretely, it's also a problem that when
doing a V=1 build in a terminal, the relevant HAB blocks lines easily
drown in all the other V=1 output.
Moreover, build systems such as Yocto by default pass V=1, so in that
case the information gets hidden away in the do_compile log file, making
it nigh impossible to create a recipe for creating signed U-boot images
- I don't want to disable V=1, because having verbose output in the log
file is valuable when things go wrong, but OTOH trying to go digging in
the do_compile log file (and getting exactly the right lines) is not
pleasant to even think about.
So change the logic so that for V=0, the mkimage output is redirected
to MKIMAGEOUTPUT (which is also the current behaviour), while for any
other value of V, we _additionally_ write the information to make's
stdout, whatever that might be.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Breno Lima <breno.lima@nxp.com>
Drop the CONFIG_MMC_RENESAS_TUNING symbol from Gen3 configs.
This symbol is no longer used after the Matsushita SDHI driver,
instead the renesas-sdhi driver uses CONFIG_MMC_HS200_SUPPORT
to discern whether the tuning support should be compiled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
--
V2: Submit this on top of configs which are actually in mainline
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Shrink the TPL by using tiny printf and tiny memset by default.
This removes the biggest symbol -- vsnprintf_internal -- from
the TPL and reduces the text segment by about 2 kiB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout port was broken since some time. This patch updates
the H2 Stout port to use modern frameworks, DM, DT probing, SPL
and TPL for the preloading and puts it on par with the M2 Porter
board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout uses SCIFA0 for serial console, make sure it is
available very early on when probing from DT.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The initconst is not used in U-Boot, drop it. The r8a7790_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
- For am335x_pdu001 we do not want the CPSW driver, drop it
- Re-sync the defconfig for am43xx_evm_rtconly as it came in after the
patch that converted CPSW to Kconfig was posted but before it was
applied.
- Drop empty section / comments from pengwyn
- Drop empty section / comments from baltos and drop unused
CONFIG_SPL_NET_VCI_STRING (it does not enable CONFIG_SPL_NET_SUPPORT
currently and SPL_NET_VCI_STRING has been migrated already).
Cc: Felix Brack <fb@ltec.ch>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Fixes: f02b8d1761 ("Migrate CONFIG_DRIVER_TI_CPSW to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
Tested-by: Felix Brack <fb@ltec.ch>
Without armv8_setup_psci register VBAR_EL3 is not set up property which
makes SMC calls jump to invalid location.
smp_kick_all_cpus is required to make slave cpus leave gic_wait_for_interrupt.
Without this they will never pursue booting process.
Fix was applied to the two ways of booting VxWorks: bootvx and bootm commands.
This implementation is very similar to what is done in boot_jump_linux
in arch/arm/lib/bootm.c file.
Tested on VxWorks 7 release SR0520 2017-12-08 Intel Stratix 10 SX SoC
Development Kit board.
Signed-off-by: Vasyl Vavrychuk <vasyl.vavrychuk@globallogic.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Otherwise, we see this:
In file included from include/configs/zynq-common.h:183:0,
from include/config.h:5,
from include/common.h:21,
from env/common.c:11:
include/config_distro_bootcmd.h:319:2: error: expected ?}? before ?BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE?
BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE
^
include/config_distro_bootcmd.h:319:2: note: in definition of macro ?BOOTENV_DEV_NAME_PXE?
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
This reverts the parts of commit 3b3ea2c56e
where it changed the EFI dependency on NET.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
The BOOTP options used to be and should still be default for all boards
with CMD_NET enabled. One should not be forced to use DISTRO_DEFAULTS to
get them.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Improve the documentation and correct the listed dependencies.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Commit 3b3ea2c56e ("Kconfig: cmd: Make networking command dependent on NET")
removed the help documentation from the README but didn't add it back to Kconfig.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Move DHCP to directly follow BOOTP so that Kconfig can show the
dependency as a hierarchy.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Options that controlled the tftp and bootp commands depended on their
commands, but lived in the net menu.
Move them so they are in a consistent location.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
PING requires CMD_NET, not NET.
Also, CMD_NET already depends on NET, so no need to directly depend
on it.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously, CMD_NET was an alias for 2 commands (bootp and tftpboot) and
they we not able to be disabled. Separate out those 2 commands and move
CMD_NET up to the menu level, which more accurately represents the code.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Duncan Hare <dh@synoia.com>
Add support to use max-speed property from dt for
determining the supported speed. Use 1000Mbps as
default.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the probe function has changed to reset FEC controller prior than
setup PHY. If reset FEC controller timeout, the priv->phydev is not
initialized, so can't free it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
On i.MX6SX, 6UL and 7D, there are two enet controllers each has a
MDIO port. But Some boards share one MDIO port for the two enets. So
introduce a configuration CONFIG_FEC_MXC_MDIO_BASE to indicate
the MDIO port for sharing.
In Kconfig, user needs enable CONFIG_FEC_MXC_SHARE_MDIO first to enter
the CONFIG_FEC_MXC_MDIO_BASE.
To i.MX28, adapt to use the new config
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
To platforms has two enet interface, using dev->seq could
avoid conflict.
i.MX6UL/ULL evk board net get the wrong MAC address from fuse,
eth1 get MAC0 address, eth0 get MAC1 address from fuse. Set the
priv->dev_id to device->seq as the real net interface alias id then
.fec_get_hwaddr() read the related MAC address from fuse.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No need to provide two prototype for this function.
Use ulong for the first parameter, then this function
could be shared for DM/non DM case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When using ethernet DM driver, the recv interface has a
change with non-DM interface, that driver needs to set
the packet pointer and provide it to upper layer to process.
In fec driver, the fecmxc_recv functions does not handle the
packet pointer parameter. This may cause crash in upper layer
processing because the packet pointer is not set.
This patch allocates a buffer for the packet pointer and free it
through free_pkt interface.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
mvneta already supports setting the MAC address but this was only done
internally when some other part of U-Boot tries to actually use the
interface. This commit exposes this functionality to the ethernet core
code so that the MAC addresses of all interfaces are configured
correctly even if they are not used before loading Linux.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Make it possible to use gcc code coverage analysis.
v1 -> v2:
- Kconfig: remove not needed 'default n'
- Makefile: use consistent spacing
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The dwc_ahci has been broken for quite some time now. The breakage has been
introduced by the series "dm: scsi: Enhance SCSI support for driver model"
Use ahci_bind_scsi() and ahci_probe_scsi() to properly bind and probe the
driver.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The Gen3 kernel images are often above 8 MiB, increase the
maximum kernel size to 64 MiB to future-proof it, just like
many other ARM64 boards do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix up the memory map on Gen3 to match datasheet properly.
This simplifies the memory map setup as well, since we do
no longer need this massive complexity.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The QSPI controller on RCar Gen2 has 32byte FIFO. Instead of doing
the SPI transmission 1 byte at time, if there is a 32byte chunk of
data to be transferred, fill the FIFO completely and then transfer
the data to/from the FIFO. This increases the SPI NOR access speed
significantly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Replace the ad-hoc endless loops with wait_for_bit() with
reasonable timeout. Note that the loops had internal 10uS
delays, although there is no reason for those on this HW,
so they are dropped.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Add driver for the RPC block in SPI-flash mode. This driver allows
access to a SPI NOR flash attached to the RPC block and does not
support RPC in Hyperflash mode. Note that this block is extremely
selective when communicating with the SPI NOR.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add driver for the RPC block in Hyperflash mode. This driver allows
access to a CFI Hyperflash attached to the RPC block and does not
support RPC in SPI mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Make sure to wait for the command to complete altogether, including
the trailing 8 clock cycles. This prevents the driver for accidentally
writing the CMD register too fast before the previous command fully
completed.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
There are only a few registerse used in the 16bit mode which are
32bit internally. Special-case only those in the IO accessors and
always write both halves. Any other register access is protected
from accidentally overwriting neighboring register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Handle the controller version even if quirks are set. The controller in
Renesas Gen3 SoCs does provide the version register, which indicates a
controller v10 and the controller does support internal DMA and /1024
divider.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The DMA READ completion flag position differs on Socionext and Renesas
SoCs. It is bit 20 on Socionext SoCs and using bit 17 is a hardware bug
and forbidden. It is bit 17 on Renesas SoCs and bit 20 does not work on
them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
On the Renesas version of the IP, the /1 divider is realized by
setting the clock register [7:0] to 0xff instead of setting bit
10 of the register. Check the quirk and handle accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add a quirk to identify that the controller is Renesas RCar variant
of the Matsushita SD IP and another quirk indicating it can support
Renesas RCar HS200/HS400/SDR104 modes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The Renesas RCar Gen2 chips have a mix of 32bit and 16bit variants
of the IP. There is no DT property which allows discerning those,
so what Linux does is it checks the size of the register area and
if it is 0x100, the IP is 16bit, otherwise the IP is 32bit. Handle
the distinction the same way.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Certain instances of the SD IP require more elaborate digging
in the DT to figure out which variant of the SD IP is in use.
Allow explicit passing of the quirks into the probe function.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for 16bit mutation of the Matsushita SD IP. Since some
registers are internally 32bit, the matsu_sd_{read,write}l() has
to special-case this 16bit variant a bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add macros to generate the FIFO accessors, since the code is almost
the same with only minor differences. This is done in preparation
for adding 16bit variant of the IP.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Factor out common code from the uniphier SD driver, change the prefix
of the functions from uniphier_sd_ to matsu_sd_ and create separate
renesas-sdhi.c driver. Thus far, all the code is still compiled when
CONFIG_UNIPHIER_MMC is selected and there is no functional change.
This patch is a preparation for further split of the SoC specific
parts of the Matsushita SD driver, used both on Uniphier and R-Car.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Skip the cache initialization, which can be done later on in U-Boot
proper, since this interferes with early DRAM initialization in TPL.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull the SPL code from porter.c into a separate file in
preparation for the addition of system initialization code.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch is a preparation for adding TPL support for RAM loading.
CONFIG_IS_ENABLED allows for proper handling of the U-Boot/SPL/TPL
differences in config symbol names.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
The tiny variants of memset and memcpy implementations can be
built for TPL as well, check whether a TPL build is in progress
and avoid including the default variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This patch fixes a situation where CONFIG_DM_SERIAL is enabled for
regular U-Boot and SPL, but not for TPL. In that case, the build
will try to include serial-uclass into the TPL nonetheless, because
CONFIG_DM_SERIAL is set.
The solution is to check if the build is for SPL or TPL and in that
case, check if CONFIG_$(SPL_TPL_)DM_SERIAL is also set. Only in that
case, include serial-uclass.c . If the build is for regular U-Boot,
CONFIG_BUILD is not set, so only check if CONFIG_DM_SERIAL is set
and if so, include serial-uclass.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add Kconfig entry for CONFIG_SPL_SPI_LOAD symbol and move all
configurations using it to Kconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
The Amlogic Meson GXL and GXM (simple variant) embeds up to 3 USB2 PHYs
and an USB3 PHY. This patch adds drivers for these for the standard generic
PHY interface and supports the power-on/off calls and set the Host mode by
default.
They are based on the excellent work from Martin Blumenstingl merged in linux.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
DWC3 Ips can have more than 1 PHY for USB2 and 1 PHY for USB3, add support
for a generic number of PHYs and adapt the code to handle a generic
number of PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add an option to get the clock speed from the device tree, hence adding
compatibility with DM clock drivers.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Since bus translations are now fully supported, use a plain
"dev_read_addr" to get the device address from the device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The fpgamap interface has been switched to a "single function + data
size" interface. Reflect this change in the IHS I2C driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The commit implement a gpio-based software deblocking. The code
extract I2C pins description from device tree, switch pins to GPIO
mode, toggle SCL until slave release SDA, send I2C stop and switch
I2C pins back to I2C mode.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
The commit describe usage of gpios and pinctrl device tree
properties in order to enable gpio-based software deblocking.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
The mutex lock and unlock functions are stubbed out and mutex_is_locked
was 0. This caused asserts to fail in ubifs code when checking that the
mutex was locked. For example,
UBIFS assert failed in ubifs_change_lp at 540
UBIFS assert failed in ubifs_release_lprops at 278
Assume that the "mutex" is locked since that is the normal case when it
is checked in the ubifs code.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Update scripts/checkpatch.pl from upstream.
One of the many corrections is not creating an error for cover-letters.
Reintroduce U-Boot's
5c761ce586
checkpatch.pl: Add warning for new __packed additions
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Using sizeof gives the size of the pointer only, not the string. This
could easily lead to crashes when using -l argument.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
The most significant change is the addition of the --self-test option
which allows to run a consistency check on all MAINTAINERS files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch adds the bulk clock API tests for the sandbox test suite.
It's very similar to the main test but only uses the _bulk() API and
checks if the clocks are correctly enabled/disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a "bulk" API to the clock API in order to get/enable/disable
/release a group of clocks associated with a device.
This bulk API will avoid adding a copy of the same code to manage
a group of clocks in drivers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the bulk reset API tests for the sandbox test suite.
Unlike the main test, it also check the "other" reset signal using the bulk API
and checks if the resets are correctly asserted/deasserted.
To allow the bulk API to work, and avoid changing the DT, the number of resets
of the sandbox reset controller has been bumped to 101 for the "other" reset
line to be valid.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a "bulk" API to the reset API in order to get/deassert/
assert/release a group of reset signals associated with a device.
This bulk API will avoid adding a copy of the same code to manage
a group of reset signals in drivers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without the units these numbers are confusing. Add a comment about the
unit being 'bytes' and mention 'buildman' as the source.
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
If there is a problem with the parameters to log_add_filter(), the memory
allocated is currently not freed. Fix this.
Reported-by: Coverity (CID: 171962)
Signed-off-by: Simon Glass <sjg@chromium.org>
Similarly to ARMV7, on ARMV7M instruction cache memory needs
to be disabled before running linux kernel to avoid kernel to
be stuck.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The Amlogic Meson SoCs serial bindings were not written when serial
support was pushed into Linux and U-Boot.
A clean bindings document has been merged into Linux tree to correctly
handle the multiple clocks feeding the serial peripheral.
This update the U-Boot serial_meson driver with the new compatible
string for Amlogic Meson GX Socs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Patch queue for efi - 2018-04-09
Highlights this time around:
- Lots of minor spec compliance fixes
- Support full range of GOP BLT commands
- More fine grained error checking
- Network fixes (init, DP)
- Lots of other bug fixes...
Inspired by the following kernel commit:
"commit 90fda63fa1156ec1bcfd7f9ca384cec221f70a21
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sat Apr 7 13:31:23 2018 -0700
treewide: fix up files incorrectly marked executable
Joe Perches noted that we have a few source files that for some
inexplicable reason (read: I'm too lazy to even go look at the history)
are marked executable:
drivers/gpu/drm/amd/amdgpu/vce_v4_0.c
drivers/net/ethernet/cadence/macb_ptp.c
A simple git command line to show executable C/asm/header files is this:
git ls-files -s '*.[chsS]' | grep '^100755'
and then you can fix them up with scripting by just feeding that output
into:
| cut -f2 | xargs chmod -x
and commit it.
Which is exactly what this commit does.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>"
Do the same in the U-Boot source tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for zc12xx boards. All of them are internal boards for
silicon validation and share very similar base platforms.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This part hasn't been pushed to mainline yet that's why remove it.
The patch can be reverted in future when this is pushed there.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
This patch enables the fixed link support for
all ZynqMP boards.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
U-Boot is now able to boot to ARM Trusted Firmware (ATF). The boot
flow is SPL(EL3) loads ATF and full u-boot and jump to ATF(EL3) which
pass control to full u-boot(EL2). This has been tested on zcu106, so
enable it in this defconfig.
To generate an image that triggers this booting flow, you need to pass
'-O arm-trusted-firmware' to mkimage.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads phytype from property "xlnx,phy-type" instead
od simply looking for "phy-type". This is to be inline with
Linux and also fixes the issue of detecting it wrongly in
u-boot.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch uses writeq() function to enable greater than 32 bit
addressing of axi-ethernet for the ZynqMP devices.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In commit 2453c69518 ("arm64: zynqmp: nand: Fixed NAND erase issue for
size 1GiB or more"), ARASAN_NAND_MEM_ADDR1_PAGE_MASK macro changed
to 0xFFFF and the same macro is used in nand write and so that getting
nand write error.
This patch reverted this macro to the 0xFFFF0000 and used
ARASAN_NAND_MEM_ADDR1_COL_MASK in the nand erase function
which is equal to 0xFFFF.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is delay needed after PCFG_PROGB change if
AES key source is efuse. This fixes the issue of
encrypted bitstream loading with AES efuse as key
source.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilfpga library expects the size of bitstream in a pointer
but currenly we are passing the size as a value. This patch
fixes this issue.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Latest xilfpga expects to set BIT5 of flags for nonsecure
bitsream and also expects length in bytes instead of words
This patch does the same.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for ZynqMP platform to print FPGA PCAP status
for "fpga status" command.
Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch fixing issues reported by DTC:
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x400000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0x800000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xc00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xd00000 unit name should not have
leading "0x"
zynq-cc108.dtb: Warning (unit_address_format): Node
/amba/spi@e000d000/flash@0/partition@0xf00000 unit name should not have
leading "0x"
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Using different node name and label partitions as data.
Also use latest compatible strings based on mainline review.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mainline Linux kernel has adopted SPDX header license in a different
format then was used before. This patch is syncing it up.
Also update years in License text and remove Nathalie's email because it
is no longer valid.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sync pcie and lpd_dma nodes with mainline version.
Incorrect locations are causing diff in statistics that's why
synchronizations are needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The portable executable header has a field describing the machine type.
The machine type should match the binary. So on i386 we should use
IMAGE_FILE_MACHINE_I386 and on x86_64 we should use
IMAGE_FILE_MACHINE_AMD64. The actual value is issued by the objcopy
command invoked in scripts/Makefile.lib in depdendence of the value of
EFI_TARGET.
The value is used both for EFI_STUB and for EFI_LOADER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Delete devices implemented in PL, stylistic changes.
Signed-off-by: Anton Gerasimov <tossel@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
CONFIG_VERSION_VARIABLE had already been mostly migrated to Kconfig,
but two headers still referenced it. Also set defaults so that
most of the defconfigs inherit the default rather than needing it
to be set explicitly.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Convert CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to Kconfig
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Petr Vorel <petr.vorel@gmail.com>
Reviewed-by: Petr Vorel <petr.vorel at gmail.com>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
When compiling without CONFIG_CLOCK_SYNTHESIZER (which is implied by
CONFIG_DRIVER_TI_CPSW for am335x_evm), exclude the network setup for
AM335x-ICEv2 to avoid link time failures:
board/ti/am335x/board.c:683: undefined reference to `setup_clock_synthesizer'
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
In order to compile the USB Ethernet gadget support we require that NET
is enabled, add that dependency here.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If DHCP/PXE commands are disabled then the compilation fails due to
bootargs attempting to use them:
include/config_distro_bootcmd.h:319:2: error: expected ‘}’ before ‘BOOT_TARGET_DEVICES_references_PXE_without_CONFIG_CMD_DHCP_or_PXE’
Ensure that if the command aren't enabled, we don't try and use them.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CONFIG_HOSTNAME is defined as a "plain" preprocessor string, but every
use is couched by __stringify(...).
Hence, convert it to a proper string option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Migrate the CONFIG_DISPLAY_BOARDINFO_LATE option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the CONFIG_SYS_ALT_MEMTEST option to Kconfig.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
[trini: Re-run migration after also including CMD_MEMTEST]
Signed-off-by: Tom Rini <trini@konsulko.com>
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.
This reverts commit 7b09477873.
Signed-off-by: Tom Rini <trini@konsulko.com>
As we aren't quite able to convert some platforms with a very small size
limit in SPL yet, we need to revert this for now.
This reverts commit 37434db29b.
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds a command that enables the calculation of bit operations
(AND, OR, XOR) on binary data from the command line. Memory locations as
well as the contents of environment variables are eligible as sources
and destination of the binary data used in the operations.
The possible applications are manifold: Setting specific bits in
registers using the regular read-OR-write pattern, masking out bits in
bit values, implementation of simple OTP encryption using the XOR
operation, etc.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
A debug string still has the old name of a function being called; update
it.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix Kconfig alignment which should be <tab><space><space>.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL ATF implementation requires FIT image with partitions where the one
is Firmware/ATF and another one Firmware/U-Boot. OS field is used for
recording that difference that's why make sense to show values there for
Firmware types.
For example:
Image 0 (atf)
Description: ATF bl31.bin
Created: Mon Mar 26 15:58:14 2018
Type: Firmware
Compression: uncompressed
Data Size: 51152 Bytes = 49.95 KiB = 0.05 MiB
Architecture: ARM
OS: ARM Trusted Firmware
Load Address: 0xfffe0000
Hash algo: md5
Hash value: 36a4212bbb698126bf5a248f0f4b5336
Image 1 (uboot)
Description: u-boot.bin
Created: Mon Mar 26 15:58:14 2018
Type: Firmware
Compression: uncompressed
Data Size: 761216 Bytes = 743.38 KiB = 0.73 MiB
Architecture: ARM
OS: U-Boot
Load Address: 0x08000000
Hash algo: md5
Hash value: f22960fe429be72296dc8dc59a47d566
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
SPL ATF support requires to have firmware property which should be also
listed by mkimage -l when images is created.
The patch is also using this macro in spl_fit to match keyword.
When image is created:
Default Configuration: 'config'
Configuration 0 (config)
Description: ATF with full u-boot
Kernel: unavailable
Firmware: atf
FDT: dtb
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Nie <jun.nie@linaro.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Move am43xx_evm_qspiboot_defconfig to DM. This is required as SPI core
and TI QSPI driver no longer supports non DM interfaces.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Also, add -u-boot.dtsi for AM437x SK and IDK to enable I2C for
board detection via DM_I2C.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
AM437x QSPI boot is a single stage boot and hence needs runtime DTB
selection to support AM437x-SK and AM437x-IDK with DM enabled. This is
required to move am43xx_evm_qspiboot_defconfig to use DM/DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Use CONFIG_IS_ENABLED to see if CONFIG_BLK is enabled. Otherwise
SPL compilation breaks on boards which do have CONFIG_BLK enabled but
not DM_MMC for the SPL as follows:
env/mmc.c: In function ‘init_mmc_for_env’:
env/mmc.c:164:6: warning: implicit declaration of function ‘blk_get_from_parent’; did you mean ‘efi_get_ram_base’? [-Wimplicit-function-declaration]
if (blk_get_from_parent(mmc->dev, &dev))
^~~~~~~~~~~~~~~~~~~
efi_get_ram_base
env/mmc.c:164:29: error: ‘struct mmc’ has no member named ‘dev’
if (blk_get_from_parent(mmc->dev, &dev))
^~
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rx8025 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the rs5c372 implementation of
rtc_reset() does not need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the mx27rtc implementation of
rtc_reset() can be an empty stub function.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1374 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
As of commit 1a1fa24066 ("rtc: Set valid date after reset") the
command "date reset" will set the date/time to 2000-01-01 0:00:00 after
calling rtc_reset(). This means that the ds1307 implementation of
rtc_reset() doesn't need to call rtc_set().
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support of sysreset with generic driver "syscon-reboot"
provided by RCC, for U-boot and for SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
No more use static frequency HSI = 64MHz for STGEN clock
but HSE (with higher accurency) by default.
Need to remove CONFIG_SYS_HZ_CLOCK as arch timer frequency
is provided at boot by BootRom and cp15 cntfrq and modified
during clock tree initialization if needed.
When HSI is no more used by any device, this internal
oscillator can be switched off to reduce consumption.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The STGEN is the clock source for the Cortex A7 arch timer.
So after modification of its frequency, CP15 cntfreq is updated
and a new timer init is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Manage dynamic value for armv7 arch clock timer,
when CONFIG_SYS_HZ_CLOCK is not defined.
Get frequency from CP15 cntfrq information, initialized for example
by first boot stage, clock driver or by BootRom.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Modifying the default environment via CONFIG_EXTRA_ENV_SETTINGS is
somewhat inflexible, partly because the cpp language does not allow
appending to an existing macro. This prevents reuse of "environment
fragments" for different boards, which in turn makes maintaining that
environment consistently tedious and error-prone.
This implements a Kconfig option for allowing one to define the entire
default environment in an external file, which can then, for example, be
generated programmatically as part of a Yocto recipe, or simply be kept
in version control separately from the U-boot repository.
Tested-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Bootrom loads SPL from SDCARD or eMMC
according BootPin selection.
Then SPL loads U-Boot on the same mmc device
with the following predefined GPT partitioning:
on SDCARD: gpt partitioning
1: SPL
2: SPL#2
3: U-Boot
4: bootable partition
on eMMC:
The 2 boot partitions are used for SPL (2 copy)
boot1: SPL
boot2: SPL#2
The user partition use gpt partitioning
1: U-Boot
2: bootable partition
This patch select the correct SPL partition
(3 for SDCARD on mmc0 and 1 for eMMC on mmc1)
according the BootRom information saved in TAMP register
and based on configuration flasg:
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION
=> for BOOT_DEVICE_MMC1 or mmc 0 in U-Boot
- CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION_MMC2 (new)
=> for BOOT_DEVICE_MMC2 or mmc 1 in U-Boot
And the correct boot_targets is selected according the environment
variables boot_device and boot_instance, with preboot command,
to search the bootable partition with kernel on this device
(generic distro support).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
SPL copy BootRom boot mode information
in TAMP register 21.
This TAMP register information is used
after relocation to set 2 env variables
- boot_device
- boot_instance
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add command GPT support
Add EMMC boot support
Add the 2 other SDMMC instances for ED1:
- SDMMC2 = mmc 1, eMMC on the ED1 board
- SDMMC3 = extension connector, deactivated by default
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The spl_boot_partition function has been added in order to have
the possibility to boot on a same binary from different mmc devices
with different partitions.
By default keep the current behavior, SPL use the partition defined
by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The mxsimage utility fails to compile against LibreSSL version < 2.7.0
because LibreSSL says it is OpenSSL 2.0, but it does not support the
complete OpenSSL 1.1 interface.
LibreSSL defines OPENSSL_VERSION_NUMBER with 0x20000000L and therefor
claims to have an API compatible with OpenSSL 2.0, but it implements
EVP_MD_CTX_new(), EVP_MD_CTX_free() and EVP_CIPHER_CTX_reset() only
starting with version 2.7.0, which is not yet released. OpenSSL
implements this function since version 1.1.0.
This commit will activate the compatibility code meant for
OpenSSL < 1.1.0 also for LibreSSL version < 2.7.0.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Jonathan Gray <jsg@jsg.id.au>
We should not evaluate the value of reg before its value is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The boot scripts for booting from ramdisk are using
${fdtimage} when they really should be using ${fdtaddr}
This patch will fix it so the RAMdisk bootscripts operate
correctly.
Signed-off-by: Adam Ford <aford173@gmail.com>
This inhibits the re-inititialization of DDR during an RTC-only resume. If
this is not done, an L3 NOC error is produced as the DDR gets accessed
before the re-init has time to complete. Tested on AM437x GP EVM.
Signed-off-by: Russ Dill <Russ.Dill@ti.com>
[j-keerthy@ti.com Ported to Latest Master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Prevent EMIF control of DDR_RESET line on DDR3 am43xx platforms for
am43xx_evm_rtconly_config. Without this DDR is unstable and can become
corrupted after multiple iterations of RTC+DDR mode.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
[j-keerthy@ti.com Ported to latest master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Kernel stores information to the RTC_SCRATCH0 and RTC_SCRATCH1 registers
for wakeup from RTC-only mode with DDR in self-refresh. Parse these
registers during SPL boot and jump to the kernel resume vector if the
device is waking up from RTC-only modewith DDR in Self-refresh.
The RTC scratch register layout used is:
SCRATCH0 : bits00-31 : kernel resume address
SCRATCH1 : bits00-15 : RTC magic value used to detect valid config
SCRATCH1 : bits16-31 : board type information populated by bootloader
During the normal boot path the SCRATCH1 : bits16-31 are updated with
the eeprom read board type data. In the rtc_only boot path the rtc
scratchpad register is read and the board type is determined and
correspondingly ddr dpll parameters are set. This is done so as to avoid
costly i2c read to eeprom.
RTC-only +DRR in self-refresh mode support is currently only enabled for
am43xx_evm_rtconly_config.
This is not to be used with epos evm builds.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[j-keerthy@ti.com Rebased to latest u-boot master branch]
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable NETCONSOLE by default. Still requires changes to the boot
environment to enable on the platform.
Signed-of-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Texas Instruments AM3358 based low-cost board using Octavo Systems OSD3358 SIP
with built-in TPS65217 PMIC and 512MB DDR3. Board features small 35mm x
55mm size, high-speed USB OTG, microSD and 72 0.1" expansion header
pins with 2xSPI, 2xI2C, 2xUART, USB, 8xADC, up-to-44 GPIO, PRU pins and much more.
https://beagleboard.org/pocket
This was tested using the am335x_evm_usbspl_defconfig.
Note that MII pins are enabled despite not having Ethernet on this
board. This avoids an issue where otherwise many timeout errors would be
generated. See https://e2e.ti.com/support/arm/sitara_arm/f/791/t/298976
for some related discussion.
Signed-off-by: Jason Kridner <jdk@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In preparation of migration to DM watchdog, clean up a bit.
The 8xx watchdog really is a HW watchdog, so declare it as is
then it goes through Kconfig
And the watchdog reset doesn't mind getting interrupted, so
no need to disable interrupts
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
reginfo is redundant with some of the commands in immap.c, so
move reginfo into that file and remove duplicated info.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Latest versions of u-boot have increased in size and require more
than the 256kb allocated to it.
The MCR3000 board is equipped with an AM29LV160DB boot flash which
is organised as follows:
- One 16kb block
- Two 8kb block
- One 32kb block
- Thirty one 64kb blocks
At the time being, u-boot is a single piece occupying the 256 first
kbytes, then the environment is stored in the following 64kb block
The environment being quite tiny, we save one 64kb block by embedding
the environment in the first 8kb block, hence allowing to increase
the monitor size to 320kb.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Commit 7653942b10 ("common/env_embedded.c: drop support for
CONFIG_SYS_USE_PPCENV") dropped the .ppcenv section which was
used in linking scripts to allow fine placement of embedded
environment sections.
This implies that GCC randomly places objects from env/embedded.o
and environment is not guaranteed to be located at the correct address:
04003df8 g F .text 00000038 mii_init
04004000 g O .text 00000004 env_size
04004004 g O .text 00002000 environment
04006004 g F .text 00000040 .hidden __lshrdi3
This patch restores this capability by allocating each object marked
with __UBOOT_ENV_SECTION__ into a different section. Hence
'environment' will be alone in .text.environment, allowing a
fine placement in u-boot.lds with:
. = DEFINED(env_offset) ? env_offset : .;
env/embedded.o (.text.environment)
Fixes: 7653942b10 ("common/env_embedded.c: drop support for CONFIG_SYS_USE_PPCENV")
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Some config is redundant with Kconfig. Fix it.
Also remove unused configs
Move SDRAM_MAX_SIZE in the only place it is used
include/environment.h already defines CONFIG_ENV_SIZE
from CONFIG_ENV_SECT_SIZE and defines CONFIG_ENV_ADDR as
(CONFIG_SYS_FLASH_BASE + CONFIG_ENV_OFFSET)
remove BOOTARGS as bootargs is set by the different boot commands
Fix CONFIG_SYS_INIT_RAM_ADDR and CONFIG_SYS_INIT_RAM_SIZE to be in
line with CPM DPRAM organisation
Remove CONFIG_SYS_GBL_DATA_SIZE, CONFIG_SYS_GBL_DATA_OFFSET and
CONFIG_SYS_INIT_SP_OFFSET which are unused
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Since commit 17cb4b8f32 ("mtd: nand: Add+use mtd_to/from_nand and
nand_get/set_controller_data"), mtd_to_nand() has to be used instead
of mtd->priv
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
u-boot requires some RAM at startup, to store global data structure.
RAM is also needed when we migrate to DM for some initial malloc
This patch implements the proper init of that RAM by calling
board_init_f_alloc_reserve() and board_init_f_init_reserve()
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Some malloc memory is needed at startup for DM model.
Lets reorganise the use of the CPM dpram.
The MPC866/885 dpram, we have 8kbytes dual port RAM, which is usable as:
IMMR + 0x2000..0x2800: BD/Data/Microcode
IMMR + 0x2800..0x2e00: BD/Data
IMMR + 0x2e00..0x3800: BD/Data/Microcode
IMMR + 0x3800..0x3a00: BD/Data
IMMR + 0x3a00..0x3c00: BD/Data/Microcode
IMMR + 0x3c00..0x4000: Parameters for the Peripheral Controllers
Lets reallocate all BDs in the 3800..3a00 area and give the full
2800..2e00 for dynamic RAM allocation including global data
That way, the microcode areas remain available if needed one day.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
SPRN_IMMR is defined regardless of the CPU. Therefore, there
is no point in enclosing get_immr() inside a #ifdef CONFIG_8xx
As it a static inline function, it will in any case only be
compiled in functons using it.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Avoid hardcoding the PVR values in C since they are defined
in processor.h
At the same time, remove those multiple PVR values for 8xx and
keep only one that we call PVR_8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
In most places, immap local pointer is defined as
immap_t __iomem *immap = (immap_t __iomem *)CONFIG_SYS_IMMR;
In a few places, it is defined as
immap_t __iomem *immap = (immap_t __iomem *)(immr & 0xFFFF0000);
This patch replaces the few of the latest form by the other one.
The two are fully equivalent since SPRN_IMMR is set with CONFIG_SYS_IMMR
very early in start.S
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
commit 907208c452 ("powerpc: Partialy restore core of mpc8xx")
didn't bring back support for I2C on the mpc8xx
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
ATMEL_SPI is now fully converted to driver-model and
respective boards switch to DM_SPI as well,
so make default y for ARCH_AT91
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
atmel_spi.h has register offsets, and atmel_spi_slave
structure, move it into .c file for better readability
and drop atmel_spi.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
All board configs are now enabled DM_SPI for SPL and
U-Boot proper, so now its time to drop non-dm code.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
AT91 ma5d4evk board uses atmel spi driver, enable DM_SPI to
use dm functionality.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Sync DTS from Linux and add FDT support for AT91 ma5d4evk board.
usb0, usb1, usb2 and hlcdc_pwm nodes removed, since there is no support it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI for atmel SPI driver on taurus board.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Few boards are configuring gpio directly from board instead
using drivers/gpio so add ifdef for DM_GPIO to compatible
for both the cases.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Wenyou Yang <wenyouya@gmail.com>
In the model table for the new revision code encoding documented in
https://www.raspberrypi.org/documentation/hardware/raspberrypi/revision-codes/README.md
add the entries for old models with the new scheme and add CM3 which
only appears in the new scheme.
A device tree for CM3 is not currently upstreamed in linux. When that
happens the name will likely have to be adjusted in the table.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
With legacy boot (booti, bootz), people can declare memory regions as
reserved using device tree memory reservations. This feature is some
times used to indicate memory regions that should not be touched.
Since in a UEFI world, the DT memory reservations do not get honored,
let's copy them into the UEFI memory map so everyone has a coherent
view of the world and we give people the chance to add reservations
on demand.
Signed-off-by: Alexander Graf <agraf@suse.de>
Check FileHeader.Machine to make sure the EFI executable image is built
for the same architecture. For example, 32-bit U-Boot on x86 will print
an error message instead of loading an x86_64 image and crashing.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add missing network initialization code.
Before the patch the network was only usable if a network command like
dhcp or tftp had beed executed.
This was visible when interrupting the console countdown and executing
bootefi selftest for vexpress_ca15_tc2_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If an exception occurs in a UEFI loaded image we need the start address of
the image to determine the relocation offset.
This patch adds the necessary lines after the registers in the crash dump.
A possible output would be:
UEFI image [0xbffe6000:0xbffe631f] pc=0x138 '/\snp.efi'
With the offset 0x138 we can now find the relevant instruction in the
disassembled 'snp.efi' binary.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Introduce functions to print information about loaded images.
If we want to analyze an exception in an EFI image we need the offset
between the PC and the start of the loaded image.
With efi_print_image_info() we can print the necessary information for a
single image, e.g.
UEFI image [0xbffe6000:0xbffe631f] pc=0x138 '/\snp.efi'
efi_print_image_infos() provides output for all loaded images.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In raspberrypi-firmware 7fdcd00e00a42a1c91e8bd6f5eb8352fe9358557 and
later start.elf now sets the EMMC clock to 200 MHz.
According to Phil Elwell in
https://github.com/raspberrypi/firmware/issues/953
the SDHost controller shares the core/VPU clock and doesn't use
the EMMC clock.
Use the core clock id when determining the frequency to allow
U-Boot to work with recent versions of raspberrypi-firmware.
Otherwise U-Boot hangs at:
U-Boot 2018.03 (Mar 14 2018 - 20:36:00 +1100)
DRAM: 948 MiB
RPI 3 Model B (0xa02082)
MMC: mmc@7e202000: 0, sdhci@7e300000: 1
Loading Environment from FAT...
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
The Raspberr Pi Foundation released a new RPi3 version which we want
to detect as well, so we can enable ethernet on it and know the correct
device tree file name.
Add an identifier for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
The new Raspberry Pi B 3+ has a lan78xx device attached to it. Let's add
driver support in U-Boot for it.
Signed-off-by: Alexander Graf <agraf@suse.de>
When we enable CONFIG_OF_BOARD on Raspberry Pis, we may end up without
serial console support in early boot. Hence we need to make the serial
port optional, otherwise we will never get to the point where serial
would be probed.
Signed-off-by: Alexander Graf <agraf@suse.de>
Check that the getinfo() service of the file protocol correctly
returns the partion label.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_selftest_disk_image.h contains a disk image. We use it to test the
EFI_FILE_PROTOCOL. The patch sets the partition label to 'U-BOOT TEST'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the information type EFI_FILE_SYSTEM_INFO in the service
GetInfo() of the EFI_FILE_PROTOCOL.
The volume label is not available in U-Boot. As a work-around use the
partition name instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When converting an ASCII string to UTF-16 don't forget to copy the
trailing \0.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The device path of the loaded image should be set to the partition
from which the image was loaded. This requires using the same logic as
the load command.
Without the patch the device path pointed to the whole disk after executing
load mmc 0: 0x43000000 FILE
and not to the boot partition from which the file was actually loaded.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the EFI_FILE_PROTOCOL buffer sizes and positions are passed as UINTN and
not as u64.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should not use void * but specific types for
* device_handle
* file_path
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
According to the Portable Executable and Common Object File Format
Specification the image size must be a multiple of the alignment
of sections.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
For analyzing crash output the relocation address and size are needed.
Save them in the loaded image info.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We generally use efi_uintn_t where the UEFI spec uses UINTN.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Since the backing memory for a new device path can contain stale
data we have to make sure that we zero the buffer. Otherwise some
code paths that don't set all fields in a structure backed by this
device path might contain unwanted stale data.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The efi_pxe_mode struct which represents the PXE_BASE_CODE_PROTOCOL
Replace the placeholder paddings in the efi_pxe_mode struct with the
actual fields as defined in UEFI's PXE Base Code Protocol. Since
our efi_ip_address is a simple char array set a specific alignment
to the efi_ip_address fields, as expected by the UEFI spec.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
[agraf: s/pxe_discovervalid/pxe_discover_valid]
Signed-off-by: Alexander Graf <agraf@suse.de>
When CONFIG_DM_ETH is set, we assemble the device path properly with a
full device hierarchy. Our helper function dp_fill() even put the MAC
node itself in it for us.
However, for non-DM compatibility we also have code in that added the
MAC node manually. That code now runs on top of the existing MAC node:
Handle 0x3db2f6b0
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]
/USBClass(0,0,9,0,0)/USBClass(424,9514,9,0,2)/MacAddr(b8:27:eb:e1:81:47,1)
/MacAddr(b8:27:eb:e1:81:47,57)/EndEntire
We obviously don't need the additional node and in fact, grub chokes on
it and fails to match the DP against the ethernet device node. So this
patch moves the additional MAC node into the non-DM code path:
Handle 0x3db3fde0
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]
/USBClass(0,0,9,0,0)/USBClass(424,9514,9,0,2)/MacAddr(b8:27:eb:e1:81:47,1)
/EndEntire
While at it, we also mark the non-DM MAC node as ethernet.
Fixes: b66c60dde9 ("efi_loader: add device-path utils")
Signed-off-by: Alexander Graf <agraf@suse.de>
The efi_add_runtime_mmio function incorrectly returned the added
address as return value rather than EFI_SUCCESS. Fix it by checking
the return value of efi_add_memory_map properly.
Fixes: f057cfef5dc ("efi_loader: exit status for efi_reset_system_init")
Signed-off-by: Alexander Graf <agraf@suse.de>
The GOP path was optimized, but still not as fast as it should be. Let's
push it even further by trimming the hot path into simple 32bit load/store
operations for buf->vid 32bpp operations.
Signed-off-by: Alexander Graf <agraf@suse.de>
We usually try to compile for size, not for speed. Unfortunately with the
more powerful GOP infrastructure to handle all sorts of GOP operations, we
end up slowing down our copying hot path quite a lot.
So this patch moves the 4 possible GOP operation modes into separate
functions which call a common function again. The end result of that is
more optimized code that can properly do constant propagation throughout
its switch() statements and thus removes compares in the hot path.
Signed-off-by: Alexander Graf <agraf@suse.de>
We optimize for size using -Os so gcc might ignore 'inline'.
Pixel conversions are called so often that we always want to inline them.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When the TPL is lowered queued events may become eligible for execution.
iPXE uses the following pattern to request event execution:
bs->RestoreTPL ( TPL_APPLICATION );
bs->RaiseTPL ( TPL_CALLBACK );
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We use a timer to poll the network.
iPXE is used for booting from iSCSI drives. It has been changed to run at
TPL_CALLBACK most of the time (which is not what the UEFI spec
recommends).
By changing our timer to TPL_NOTIFY we can ensure that it is nevertheless
executed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the Blt service of the EFI_GRAPHICS_OUTPUT_PROTOCOL the parameter delta
is measured in bytes and not in pixels.
The coding only supports delta being a multiple of four. The UEFI
specification does not explicitly require this but as pixels have a size of
four bytes we should be able to assume four byte alignment.
The corresponding unit test is corrected, too. It can be launched with
setenv efi_selftest block image transfer
bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Supply a unit test for event groups.
Create multiple events in an event group. Signal each event once and check
that all events are notified once in each round.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Include libfdt.h was moved by commit b08c8c4870 ("libfdt: move headers to
<linux/libfdt.h> and <linux/libfdt_env.h>")
Fixes: e236200c7fa6 ("efi_selftest: check installation of the
device tree")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The headers are not in the correct order. Fix this. Also drop libfdt_env.h
since it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rebased
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Using the existing predefined constants is less error prone and
makes the code easier to read.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a unit test for the EFI_SIMPLE_TEXT_INPUT_PROTOCOL.
The unicode character and the scan code are printed for text
input.
To run the test:
setenv efi_selftest text input
bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
EFI_RESET_PLATFORM_SPECIFIC is one of the values that can be used for the
EFI service ResetSystem. The missing definition is added. The value has to
handled in efi_reset_system().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The test checks all block image transfer operations of the graphical output
protocol. An animated submarine is shown.
To run the test:
setenv efi_selftest bock image transfer
bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
With the patch all block image transfer operations of the
EFI_GRAPHICS_OUTPUT_PROTOCOL are supported.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If an event of a group event is signaled all other events of the same
group are signaled too.
Function efi_signal_event is renamed to efi_queue_event.
A new function efi_signal_event is introduced that checks if an event
belongs to a group and than signals all events of the group.
Event group notifciation is implemented for ExitBootServices,
InstallConfigurationTable, and ResetSystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Event groups are used to signal multiple events at the same time.
They are identified by GUIDs. This patch provided the predefined
GUIDs of UEFI specification 2.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Fix formatting errors in efi_boottime.c indicated by
scripts/checkpatch.py.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Check that parameter guid is not NULL. This avoids a possible NULL
pointer exception.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Don't set unicode_char if scan_code is set.
Add support for page up, page down, and insert.
Correct input of function keys.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The unit test checks if a device tree is installed. It requires that the
'compatible' property of the root node exists. If available it prints the
'serial-number' property.
The serial-number property is derived from the environment variable
'serial#'. This can be used to check if the image_setup_libfdt() function
is executed.
A Python test is supplied. It sets a value for serial# and checks that the
selftest shows this as serial-number.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The second argument of the bootefi command should always be usable to
specify a device tree. This was missing for bootefi selftest and
bootefi hello.
Proper error handling is added.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Up to now errors in the initialization of the EFI subsystems was not
checked.
If any initialization fails, leave the bootefi command.
We do not retry initialization because this would require to undo all prior
initalization steps.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The return type of do_bootefi_exec() is efi_status_t. So in case
of an error we should always return an EFI status code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
All EFI initialization functions should return a status code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_reset_system_init provides the architecture or board specific
initialization of the EFI subsystem. Errors should be caught and
signalled by a return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_init_obj_list() should be executed only once.
Rather than having the caller check this variable and the callee set it,
move all access to the variable inside the function. This reduces the
logic needed to call efi_init_obj_list().
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_watchdog_register() should always return a status code and not
a boolean value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Consistently return status codes form efi_net_register().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
All initialization routines should return a status code instead of
a boolean.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Convert warnings to debug() prints]
Signed-off-by: Alexander Graf <agraf@suse.de>
Errors may occur inside efi_smbios_register().
- Return a status code.
- Remove unused variables.
- Use constants where applicable.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provides information about
- usage of the bootefi command
- overview of UEFI
- interaction between U-Boot and EFI drivers
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Delete README.efi. It is replaced by a further patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Not complete, but enough for Shell.efi and SCT.efi. We'll implement the
rest as needed or once we have SCT running properly so there is a way to
validate the interface against the conformance test suite.
Initial skeleton written by Leif, and then implementation by Rob.
Signed-off-by: Leif Lindholm <leif.lindholm@linaro.org>
[Fill initial skeleton]
Signed-off-by: Rob Clark <robdclark@gmail.com>
[Rebase on v2018.03-rc1]
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add parameter checks in efi_load_image().
Check memory allocation is successful in efi_load_image().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Now with the MMC environment gone, we have enough space to accommodate
the Pine64 "non-plus" .dtb again.
This reverts commit 47952b8e42.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In January some commits were introduced to mitigate the U-Boot image
size issues we encountered on sunxi builds.
Now with the MMC environment removed we can bring them back, as we
practically don't have a size limit anymore.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Since the dawn of time for the Allwinner support in mainline U-Boot
we store the environment to the SD card and write directly at
544KB from the beginning of the device. This leads to problems when
the U-Boot proper image grows beyond 504KB and eventually overlaps.
With one release of having the environment preferably in a FAT
partition, let's now turn off the MMC variant fallback, so we get back
all the space we need to implement features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
The original DT binding used by U-Boot's sun8i-emac driver was not really
agreed upon, and deviated from the "official" binding now used by the
kernel. Since now all U-Boot users have been converted to the new
binding, we can remove support for the old DT nodes from the driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The U-Boot driver for the sun8i-emac was using some preliminary DT
binding. Now since Linux got its own driver in v4.15 and our driver
can now cope with both bindings, let's convert the DT nodes used by the
OrangePi PC2 over to the new bindings used by the kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The U-Boot driver for the sun8i-emac was using some preliminary DT
binding. Now since Linux got its own driver in v4.15 and our driver
can now cope with both bindings, let's convert the DT nodes used by the
various H3 boards over to the new bindings used by the kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The U-Boot driver for the sun8i-emac was using some preliminary DT
binding. Now since Linux got its own driver in v4.15 and our driver
can now cope with both bindings, let's convert the DT nodes used for the
Pine64+ board over to the new bindings used by the kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Ethernet MAC used in newer Allwinner SoCs (H3, A64, H5) got an
upstream Linux driver in v4.15.
This one uses a slightly different binding from the original one used
by the U-Boot driver.
The differences to the old binding are:
- The "syscon" address is held in a separate node, referenced via a
phandle in the "syscon" property.
- The reference to the PHY is held in a property called "phy-handle",
not "phy".
- The PHY register is at offset 0x30 in the syscon device, not at 0.
- The internal PHY is activated when the node, which phy-handle points
to, is a child node of an "allwinner,sun8i-h3-mdio-internal" node.
Teach the U-Boot driver how to find its resources in a "new-style" DT,
so that we can use a Linux kernel compatible DT for U-Boot as well.
This keeps support for the old binding for now, to allow a smooth
transition.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Linux kernel driver for the Allwinner pin controller gained support
for generic properties, which are now also used in the DTs.
The sun8i-emac Ethernet driver for new Allwinner MACs reads the pins from
the DT, but so far only supported the old binding.
Update the parsing routine to cope with both the old and new bindings,
so that the newer DTs can be used with U-Boot and its Ethernet driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi GPIO driver is missing some compatible strings for recent
SoCs. While most of the sunxi GPIO code seems to not rely on this (and
so works anyway), the sunxi_name_to_gpio() function does and fails at
the moment (for instance when resolving the MMC CD pin name).
Add the compatible strings for the A64 and V3s, which were missing
from the list. This now covers all pinctrl nodes in our own DTs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
As we are running into issues where the final U-Boot FIT image file is
exceeding our size limit, add a hint to the README.sunxi64 file
to point out the possibility of building non-debug versions of the ATF
binary. These are about 12KB smaller than the standard debug build, and
so allow successful U-Boot builds for many boards with the Allwinner H5
SoC.
Please note that under normal circumstances the debug build is still
recommended, as it gives valuable clues in case something goes wrong in
the ATF.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With the most recent tools for ARC (arc-2017.09) in case of
"naked" function compiler throws a warning:
---------------------------------->8-----------------------------
board/synopsys/hsdk/hsdk.c: In function 'hsdk_core_init_f':
board/synopsys/hsdk/hsdk.c:345:1: warning: stack usage computation not supported for this target
}
^
---------------------------------->8-----------------------------
That happens because the compiler doesn't handle "naked" functions
as a special case where stack calculation shouldn't be done.
But for now until this is fixed in GCC to get clean buildman output
we're disabling stack-usage check for ARC.
See https://lists.denx.de/pipermail/u-boot/2018-April/324455.html
for more background.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
More ARC changes and fixes for v2018.05
* Update of ARC tools to the most recent arc-2017.09
* Fix for compile-time warning for AXS10x
* Add support of platform-specific commands for HSDK
* Add support for on-board SPI flash on HSDK
Note though that for write support another series [1]
is required. I hope that Jagan will be able to review and
act on SPI flash improvement series before we get beyond RC1.
Also note that to get clean build for HSDK we need to disable
stack-usage check [2] as our current GCC erroneously tries to calculate
stack-usage on a naked function which leads to warning.
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=35796
[2] https://patchwork.ozlabs.org/patch/894139/
Add NAND parameters to the Nintendo NES Classic configuration file which
features a Macronix NAND flash chip with 128kiB blocks of 2kiB pages
plus 64 OOB bytes.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Move the NAND parameters from defconfig files to Kconfig for SUNXI
architecture only. Fort now only the CHIP pro is migrated.
It would have been better to convert this defconfig entry to Kconfig for
all supported machines/architectures but it has been abandoned due to a
fairly high amount of errors reported by the moveconfig.py tool. This is
due to defines quite often being multiplications of values/other defines
not correctly handled.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Make SUNXI_NAND select SPL_NAND_SUPPORT in Kconfig, this limit the
number of entries to add in defconfig files when adding NAND support.
For now, the only board using it is the CHIP pro.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Code has been changed to do not use DMA anymore with the NAND
controller, instead PIO is used. Then, DMA-specific initialization may
be dropped.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
SPL support was first written to support only the earlier generations of
Allwinner SoCs, and was only really enabled on the A13 / GR8. However,
those old SoCs had a DMA engine that has been replaced since the A31 by
another DMA controller that is no longer compatible.
Since the code directly uses that DMA controller, it cannot operate
properly on the later SoCs, while the NAND controller has not changed.
There's two paths forward, the first one would have been to add support
for that DMA controller too, the second to just remove the DMA usage
entirely and rely on PIO.
The later has been chosen because CPU overload at this stage is not an
issue and it makes the driver more generic, and easier to understand.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Prepare the future use of an helper to move the data pointer (the
column) of the NAND chip by renaming nand_reset_column() to
nand_change_column(). Resetting the column is just a matter of giving 0
as argument.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When changing the column, the ONFI specification states that a minimum
time of tCCS (Change Column Setup time) must elapse between the last
address cycle is asserted on the bus and the first data cycle is
clocked. An usual value for average NANDs is 500 nanoseconds. Round it
up to 1 microsecond to be safe.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Executing a command is matter of always doing the following sequence:
* Waiting for the FIFO to be empty so we can fill it with the new
command.
* Clearing the status register.
* Writing the command in the FIFO.
* Waiting for the command to finish.
Add a nand_exec_cmd() helper to handle this instead of repeating the
logic through the various functions.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
It is best practice to always clear the status register before executing
a command to be sure that the status read afterwards is relevant.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
One bit in the control registers indicates if the NAND controller is
ready to receive a new command. Otherwise, the command FIFO is full and
we should wait for this bit to flip. It then states that the last
command has been processed and the FIFO is now free to welcome another
command.
Add this sanity check before starting any new command.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The pattern of polling on a status register until a bit is set or a
timeout occurs is repeated multiple times in the driver. Mutualize the
code by introducing the nand_wait_int() helper that does wait for the
bit to flip or returns an error in case of timeout.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
In the nand_read_buffer() step, the seed is calculated by doing a modulo
by conf->nseeds which is always zero when not using the randomizer (most
of SLC NANDs).
This situation turns out to lead to a run time freeze with certain
toolchains.
Derive this seed only when the randomizer is enabled (and conf->nseeds
logically not zero), exactly like what has been done before with an
identical situation, see commit ea3f750c73 ("nand: sunxi: Fix modulo
by zero error").
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
When the requested ECC strength does not exactly match the strengths
supported by the ECC engine, the driver is selecting the closest
strength meeting the 'selected_strength > requested_strength'
constraint. Fix the fact that, in this particular case, ecc->strength
value was not updated to match the 'selected_strength'.
For instance, one can encounter this issue when no ECC requirement is
filled in the device tree while the NAND chip minimum requirement is not
a strength/step_size combo natively supported by the ECC engine.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
A previous commit introduced the use of binman in the SPL.
After the binman_sym call over the 'pos' symbol, the output value is
checked against BINMAN_SYM_MISSING (-1UL). According to the
documentation (tools/binman/README), when it comes to the 'pos'
attribute:
pos:
This sets the position of an entry within the image. The first
byte of the image is normally at position 0. If 'pos' is not
provided, binman sets it to the end of the previous region, or
the start of the image's entry area (normally 0) if there is no
previous region.
So instead of checking if the return value is BINMAN_SYM_MISSING, we
should also check if the value is not null.
The failure happens when using both the SPL file and the U-Boot file
independently instead of the concatenated file (SPL + padding + U-Boot).
This is because the U-Boot binary file alone does not have the U-Boot
header while it is present in the concatenation file. Not having the
header forces the SPL to discover where it should load U-Boot. The
binman_sym call is supposed to do that but fails. Because of the wrong
check, the destination address was set to 0 while it should have been
somewhere in RAM. This, obviously, stalls the board.
Fixes: 8bee2d251a ("binman: Add binman symbol support to SPL")
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
HSDK board has sst26wf016 SPI flash IC which we want to support.
Add SPI controller, CS-gpio and SPI flash nodes to hsdk device tree.
Enable corresponding options in hsdk defconfig.
For SPI write functionality to work we need [1] which
adds support of sst26xxx ICs.
[1] https://patchwork.ozlabs.org/project/uboot/list/?series=35796
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This patch add support of hsdk platform-specific commands:
hsdk_clock set - set clock from axi_freq, cpu_freq and tun_freq
environment variables/command line arguments
hsdk_clock get - save clock frequencies to axi_freq, cpu_freq
and tun_freq environment variables
hsdk_clock print - show CPU, AXI, DDR and TUNNEL current
clock frequencies.
hsdk_clock print_all - show all currently used clock frequencies.
hsdk_init - setup board HW in one of pre-defined configuration
(hsdk_hs34 / hsdk_hs36 / hsdk_hs36_ccm / hsdk_hs38 /
hsdk_hs38_ccm / hsdk_hs38x2 / hsdk_hs38x3 / hsdk_hs38x4)
hsdk_go - run baremetal application on hsdk configured
by hsdk_init command.
This patch changes default behaviour of 'bootm' command:
now we are able to set number of CPUs to be kicked by setting
'core_mask' environment variable before 'bootm' command run.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Some device tree nodes (like ethernet, ohci, ehci) in axs10x_mb.dtsi
were copied from linux device tree, so they have interrupts properties.
As we don't use interrupts in uboot we don't have interrupt controller
node in AXS10x device tree. In result we get warnings when we compile
such device tree.
So remove unused interrupts properties to get rid of this warnings.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This header needs to know 'fdt_region' is a struct for the
fit_region_make_list() prototype.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 286ede6 ("drivers: core: Add translation in live tree case") made
dev_get_addr always use proper bus translations for addresses read from
the device tree. But this leads to problems with certain busses, e.g.
I2C busses, which run into an error during translation, and hence stop
working.
It turns out that of_translate_address() and fdt_translate_address()
stop the address translation with an error when they're asked to
translate addresses for busses where #size-cells == 0 (comment from
drivers/core/of_addr.c):
* Note: We consider that crossing any level with #size-cells == 0 to mean
* that translation is impossible (that is we are not dealing with a value
* that can be mapped to a cpu physical address). This is not really specified
* that way, but this is traditionally the way IBM at least do things
To fix this case, we check in both the live-tree and non-live tree-case,
whether the bus of the device whose address is about to be translated
has size-cell size zero. If this is the case, we just read the address
as a plain integer and return it, and only apply bus translations if the
size-cell size if greater than zero.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Martin Fuzzey <mfuzzey@parkeon.com>
Reported-by: Martin Fuzzey <mfuzzey@parkeon.com>
Fixes: 286ede6 ("drivers: core: Add translation in live tree case")
Reviewed-by: Simon Glass <sjg@chromium.org>
dm_scan_fdt_node can't work when live dt is active,
we should use dm_scan_fdt_live instead.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The cast breaks the pointer on 64bit archs, so lets get rid of it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Since the new pinctrl/gpio driver is used, so this patch removes
the old board specific pin control settings.
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The commit "arm64: mvebu: Add pinctrl nodes for Armada 3700" has
added new pinctrl nodes.
This reverts commit f7cab0f95b.
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch corrects below mpp definitions for armada 3720 DB board
and ESPRESSOBin board:
- "smi" pins group is added and "smi" function is set for eth0;
- Now pcie pins are used as gpio to implement PCIe function in
hardware, so "pcie" group function is changed to "gpio".
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch corrects below mpp definitions:
- The sdio_sb group is composed of 6 pins and not 5;
- The rgmii group contains pins mpp2[17:6] and not mpp2[19:6];
- Pin of group "pmic0" is mpp1[6] but not mpp1[16];
- Pin of group "pmic1" is mpp1[7] but not mpp1[17];
- A new group "smi" is added in A0 with 2 pins - mpp2[19:18], its
bitmask is bit4;
- Group "pcie1" has 3 pins in A0 - mpp2[5:3], its bit mask is
bit5 | bit9 | bit10 but not bit4;
- Group "ptp" has 3 pins in A0 as Z1, but its bitmask is changed to
bit11 | bit12 | bit13.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43288
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Hua Jing <jinghua@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
For armada_37xx_update_reg(), the parameter offset should be pointer so
that it can be updated, otherwise offset will keep old value, and then
when offset is larger than or equal to 32 the mask calculated by
"BIT(offset)" will be 0 in gpio chip hook functions, it's an error,
this patch set offset parameter of armada_37xx_update_reg() as pointer.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43287
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible when the gpio regulator used the gpio 23, the whole
rgmii group was setup to gpio which broke the Ethernet support on the
Armada 3720 DB board. Thanks to this patch, the UHS SD cards (which need
the vqmmc) _and_ the Ethernet work again.
Reviewed-on: http://vgitil04.il.marvell.com:8080/43284
Reviewed-by: Hua Jing <jinghua@marvell.com>
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The various load address values are taken from the a37xx configuration
and match the dowstream 'u-boot-2017.03-armada-17.10' release where
appropriate.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Stefan Roese <sr@denx.de>
The kwbimage format is reading beyond its header structure if it
misdetects a Xilinx Zynq image and tries to read it. Fix it by
sanity checking that the header we want to read fits inside our
file size.
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes the network devices usable when booting a blank board over
UART, with no pre-configured MAC address stored in the environment area.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, ATU (address translation unit) implementation doesn't
support translate addresses > 32 bits.
This patch allows to configure ATU correctly for different
memory accesses (memory, configuration and IO).
The same approach is used in Linux Kernel.
Signed-off-by: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On x86 platforms, U-Boot does not pass Device Tree data to the kernel.
This prevents the kernel from using FDT loaded by U-Boot.
Read the working FDT address from the "fdtaddr" environment variable
and add a copy of the FDT data to the kernel setup_data list.
Signed-off-by: Ivan Gorinov <ivan.gorinov@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add #include <linux/libfdt.h> to zimage.c to fix build error]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
PCI enumeration may happen very early on an x86 board. The board
information pointer should have been checked in decode_regions()
as its space may not be allocated yet.
With this commit, Intel Galileo board boots again.
Fixes: 664758c ("pci: Fix decode regions for memory banks")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The get_codeseg32() wants to know if a passed in descriptor has
flag GDT_NOTSYS set (desc & GDT_NOTSYS), not whether desc and
GDT_NOTSYS are not != 0 (desk && GDT_NOTSYS).
This is an obvious typo. Fix it up.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable CONFIG_OF_BOAD to support delivery dtb to u-boot
at run time instead of embedded.
There are two methods to delivery dtb.
1 Pass from loader:
When u-boot boot from RAM, gdb or loader can pass dtb
via a2 to u-boot dynamically. Of course gdb or loader
shall be in charge of dtb delivery.
2 Configure CONFIG_SYS_FDT_BASE:
It can be configured as RAM or ROM base statically,
no mater u-boot boot from RAM or ROM.
If it was configured as ROM base, dtb can be burned
into ROM(spi flash) by spi driver.
Meanwhile remove CONFIG_SKIP_LOWLEVEL_INIT which is
useless in nx25-ae250 configuration.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Remove CONFIG_MMC_NDS32 from the three config
(adp-ae3xx_defconfig, adp-ag101p_defconfig, nx25-ae250_defconfig).
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
nsd32_mmc was created to support ftsdc010 dm.
It is not necessary to separate both, so merge it
to ftsdc010.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
CONFIG_FTSDC010_NUMBER was not used anymore,
can be removed now.
So CONFIG_FTSDC010_NUMBER
can also be removed from config_whitelist.txt.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
After drop non-dm code of ftsdc010, the sd register
base definition can be droppped now.
So CONFIG_FTSDC010_BASE and CONFIG_FTSDC010_BASE_LIST both
can be removed from config_whitelist.txt
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
Only three defconfig(adp-ag101p_defconfig,
adp-ae3xx_defconfig, nx25-ae250_defconfig)
set CONFIG_FTSDC010=y. And they all also
enable CONFIG_DM_MMC. So the non-dm code
of ftsdc010 can be dropped now.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
ftsdc010 dm driver has been disable High-Speed mode
as default to work around Andes AE3XX platform's problem,
because of it does not support High-Speed mode in
commit id 73cd56b2df.
But other platforms or SoCs maybe support this function.
So High-Speed mode can be enabled from dts with
cap-mmc-highspeed or cap-sd-highspeed property.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Simply record riscv-linux booting steps and messages
from bbl via u-boot on QEMU in README.ae250.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Add riscv uimage arch to support riscv-linux booting.
It can Convert riscv-linux to image which can be
booted by bootm command.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
ATAGS is not supported and will be replaced
by DT in riscv-linux. So can be removed now.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
riscv-linux should use BBL (Berkeley bootloader) for
loading the Linux kernel.
U-Boot can play as FSBL(first stage bootloader)
to boot BBL and riscv-linux.
In BBL's init_first_hart(), it will pass dtb with a1.
So implement bootm to pass arguments to BBL correctly.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
It is reported by checkpatch.pl
WARNING: static const char * array
should probably be static const char * const
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
It is reported by checkpatch.pl
WARNING: Missing a blank line after declarations.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
It is reported by checkpatch.pl.
CHECK: Alignment should match open parenthesis
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
It is reported by checkpatch.pl
WARNING: Use of volatile is usually wrong: see
Documentation/process/volatile-considered-harmful.rst
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
It is CHECK reported by checkpatch.pl
CHECK: Macro argument reuse 'PTE' - possible side-effects?
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
No definition provided by input.h is used in the board file.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Similarly to imx6, before reading the boot device, first check
bmode to see if the serial downloader has been selected
explicitly, then check whether the serial downloader has been
activated due to unbootable primary boot devices (e.g. empty eMMC).
If the serial downloader is activated, return BOOT_DEVICE_BOARD.
This allows SPL with SDP support to wait for the U-Boot image
to be loaded via the serial download protocol using imx_usb_loader.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Create u-boot-ivt.img and u-boot-ivt.img.log when building U-Boot
with SPL and Secure Boot enabled for imx7 (like it is done for imx6).
See commit d21bd69b6e for more info.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
The SPL MISC driver support must be enabled, so that the driver can use OTP fuse
to check if HAB is enabled.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
The i.MX6ULL has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6ULL Applications Processor Reference Manual, Rev. 1, 11/2017,
Table 2-3. AIPS-2 memory map, p. 178
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The i.MX6UL has a WDOG3 located at start address 0x021E0000 in the
AIPS-2 memory region [1].
[1] i.MX 6UltraLite Applications Processor Reference Manual, Rev. 1,
04/2016, Table-2-3 AIPS-2 memory map, p. 166
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
This fixes environment variable location to avoid overlapping with
U-Boot itself. Also more space for environment variables has been
reserved to prevent future issues.
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
HW accelerated "hash sha256 ..." command doesn't work on i.MX6UL, we get
"CAAM was not setup properly or it is faulty" error message.
This is due to wrong CAAM base 0x02100000, on i.MX6UL the CAAM base
address is 0x02140000. Fix it.
Note: with this patch applied the "hash sha256" commant still has some
issues on i.MX6UL ("Invalid KEY Command" or other errors). With data
cache off the "hash sha256" command works as expected.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP layerscape platforms like ls1088a, ls2088a
uses MXC I2C Controller.
-Remove dependency of MX6 for the same.
Update related configs to use Kconfig file.
-Add SYS_I2C_MXC_I2C1,_I2C2,_I2C3,_I2C4 in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SPEED,_I2C2_,_I2C3_,_I2C4_ in Kconfig
-Add CONFIG_SYS_MXC_I2C1_SLAVE,_I2C2_,_I2C3_,_I2C4_ in Kconfig
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
The Rockchip-specific SDHCI wrapper does not process the 'bus-width'
property in the SDHCI node. Consequently, the bus is always kept in
4bit mode, even if 8bit wide operation is available, supported and
requested in the DTS.
This change adds processing of the 'bus-width' property and sets the
host capability flag for an 8bit wide bus, if set to 8. As the logic
in sdhci.c does not support clearing the 4bit capability, we assume
that 4bit operation is always supported.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The Rockchip-specific wrappers to the DW-MMC and the SDHCI driver
were not covered as part of what's maintained by the architecture
maintainers. Add them here.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
For the RK3399-Q7, we have a fast eMMC connected in an 8 bit wide
configuration to the SDHCI controller (sdhci@fe330000). Enable DMA
within the SDHCI driver to get the best performance out of it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The patch set dpll settings for 300MHz to values used by binary
blob[1]. With new values dpll still generate 300MHz clock, but
EMAC work. Probably with new values dpll generate more stable clock.
dpll on rk3188 provide clocks to DDR and EMAC. With current
dpll settings EMAC doesn't work on radxa rock. EMAC sends packets
to network, but it doesn't receive anything. ifconfig shows a lot
of framing errors.
[1] https://github.com/linux-rockchip/u-boot-rockchip/blob/u-boot-rk3288/
tools/rk_tools/3188_LPDDR2_300MHz_DDR3_300MHz_20130830.bin
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Use of CONFIG_UBIFS_SILENCE_MSG was added in
147162dac6 ("ubi: ubifs: Turn off verbose prints")
Then it was removed in
ff94bc40af ("mtd, ubi, ubifs: resync with Linux-3.14")
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
The ti,pindir-d0-out-d1-in property is not expected to have a value
according to the device-tree binding, so treat it as a boolean not a
uint property.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Alexey:
1. Significantly rework cache-related functionality.
In particular that fixes coherency problems in some corner-cases,
allows us to enable and disable caches in run-time and still
have properly running system, finally support execution from
real flash (before we used to run from DDR from the very beginning).
2. Remove string routines implemented in assembly.
That allows us to build and run U-Boot on wide range of ARC cores
with different configurations. I.e. whatever tuning is used on GCC's
command-line we'll get code for desired flavor of ARC.
Otherwise for each and every corner-case we would need to add ifdefs
in assembly code to accommodate missing instructions etc.
3. Get use of GCC's garbage collector which helps to slim-down resulting image
quite a bit.
4. Also now we may disable U-Boot self-relocation for ARC if needed either
by platform or for debugging purposes.
Refactor GO and PREP subcommands implementation for a simpler
override in the boards platform code.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Fix my fragments to list all files in the repo.
Also fix path to for Xilinx Zynq SoC (mach-zynq)
It should be the part of
"ARM: zynq: move SoC sources to mach-zynq"
(sha1: 0107f24036)
And cover dts files in board MAINTAINERS files.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is an issue to recognize zynq or zynqmp image because header
checking is just the same. That's why zynqmp images are recognized as
zynq one.
Check unused fields which are initialized to zero in zynq format
(__reserved1 0x38 and __reserved2 0x44) which are initialized for
zynqmp. This should ensure that images are properly recognized by:
./tools/mkimage -l spl/boot.bin
Also show image type as ZynqMP instead of Zynq which is confusing.
Reported-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Alexander Graf <agraf@suse.de>
This patch adds new command "zynqmp" to handle zynqmp
specific commands like "zynqmp secure". This secure command is
used for verifying zynqmp specific secure images. The secure
image can either be authenticated or encrypted or both encrypted
and authenticated. The secure image is prepared using bootgen
and will be in xilinx specific BOOT.BIN format. The optional
key can be used for decryption of encrypted image if user
key was specified while creation BOOT.BIN.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The vcu disable bit in efuse ipdisable register is valid only
if PL powered up so, consider PL powerup status for determing
EG/EV part. If PL is not powered up, ignore EG/EV part of string.
The PL powerup status will be filled by pmufw based on PL PROGB
status in the 9th bit of version field.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
NAND erase was not happening for size 1GiB or more. Erase
command was executing successfully but in actual, it was not
erasing.
This patch fixed erase issue for 1 GiB or more size nand.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch changed CONFIG_SYS_MEMTEST_SCRATCH address to the
accessible DDR address used by alternate memory test.
Before this, 0xfffc0000 address was used, which is the OCM
address and not enabled in MMU table. So, whenever trying
to access 0xfffc0000 address, got Synchronous Abort exception.
After changing CONFIG_SYS_MEMTEST_SCRATCH address, alternate
memory test is working fine.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog is only enabled in full u-boot. Adoption for SPL should be also
done because that's the right place where watchdog should be enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This IP can be found on Zynq and ZynqMP devices.
The driver was tested with reset-on-timeout; feature.
Also adding WATCHDOG symbol to Kconfig because it is required.
Signed-off-by: Shreenidhi Shedi <imshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
watchdog clock is also connected to cpu 1X clocksource.
Zynq> clk dump
...
Before:
swdt 4294967290
After:
swdt 111111110
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
As of now newer pmufw is keeping old interfaces. That's why permit
u-boot to run on newer version. Recommended version will be setup later.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch bypasses phy detection logic for GMII interface
and just depend on phy address received from DT. This patch
is required as phy detection logic is different for some phys
like xilinx phy which can be connected over SGMII and GMII
interface.
This fixes the issue of ethernet failures when xilinx phy is
connected over GMII interface.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch is adding support to switch to EL1 while loading an EL1
application with u-boot running at EL above EL1 in aarch64 mode.
Signed-off-by: Nitin Jain <nitinj@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable Driver Model and Device-tree support for omapl138 board
in U-Boot. Also enable DM_SERIAL and DM_I2C.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync dts from Linux 4.16 and also add u-boot specific
dtsi for OMAPl138 board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 6aa4ad8e38 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
converted SOC_DA8XX to Kconfig but missed enabling DDR_INIT for
SOC_DA8XX, which broke OMAPL138 to boot.
Commit 2e87980580 ("davinci: Fix omapl138_lcdk builds") disabled
DDR_INIT for all DA850 SoCs. This failed all DA850 boards to boot
as ddr is not being initialized.
Enable SYS_DA850_DDR_INIT for DA8XX so that all DA850 and OMAPL138
will have ddr initialized
Fixes: 2e87980580 ("davinci: Fix omapl138_lcdk builds")
Fixes: 6aa4ad8e38 ("Convert CONFIG_SOC_DA8XX et al to Kconfig")
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: David Lechner <david@lechnology.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With gpio devices getting created in SPL, the size of the heap is
no longer sufficient. Therefore, increase SPL_SYS_MALLOC_F_LEN
to 0x1000.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With DM enabled in SPL, DM_FLAG_PRE_RELOC is required for
the omap_gpio driver to be bound to the gpio devices.
Therefore, add DM_FLAG_PRE_RELOC flag to the omap_gpio driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
scripts/check-config.sh exits successfully and silently without doing
any checks when the 'comm' command is not found.
The problem triggers from the command around line 39:
comm -23 ${suspects} ${ok} >${new_adhoc}
This statement fails when 'comm' is not in $PATH, creating an empty
${new_adhoc} file. But the script continues and the following line,
which is supposed to detect an error:
if [ -s ${new_adhoc} ]; then
will always be false since the file is empty, and the script will exit
successfully as if everything were OK.
The case where 'comm' in not in $PATH is not theoretical. It used to
happen on yocto until a recent fix [0], and still happens on the
current stable branch (rocko).
Fix by setting the errexit flag to exit with error when a statement
fails, so that at least the problem is noticed.
For additional safety also set the nounset flag to detect expansion
errors.
[0] http://git.yoctoproject.org/cgit/cgit.cgi/poky/commit/?id=fe0b4cb5b48580d4a3f3c0eb82bfa6f1b13801e4
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 1601dd97ed ("davinci: omapl138_lcdk: increase PLL0 frequency")
changed the PLL0 frequency to 456MHz, which is needed for the LCDC IP
block. However, in doing so, it caused the PLLOUT clock to be outside
of the allowable specifications given in the OMAP-L138 data sheet. (It
says PLLOUT must be 600MHz max). It also uses a PLLM value outside of
the range given in the TRM (it says PLLM must in the range 0 to 0x1f).
So here is what we have currently:
PLLOUT = 24 / (0 + 1) * (37 + 1) = 912MHz (out of spec)
^ ^ ^
CLKIN PREDIV PLLM (out of spec)
input to PLLDIVn = 912 / (1 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
This changes the PLLM value to 18 and the POSTDIV value to 0 so that
PLLOUT is now within specification but we still get the desired
result.
PLLOUT = 24 / (0 + 1) * (18 + 1) = 456MHz (within spec)
^ ^ ^
CLKIN PREDIV PLLM
input to PLLDIVn = 456 / (0 + 1) = 456MHz (desired result)
^ ^
PLLOUT POSTDIV
Fixes: 1601dd97ed ("davinci: omapl138_lcdk: increase PLL0 frequency")
Signed-off-by: David Lechner <david@lechnology.com>
Reported-by: Sekhar Nori <nsekhar@ti.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Last user of this driver went away in October 2014 in
commit d58a9451e7 ("ppc/arm: zap EMK boards").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In
if (a > =0) {...}
else (a < 0) {...}
the second logical constraint is superfluous.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In
int ret = A;
ret = B;
the first assignment has not effect.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The lan75xx and lan78xx drivers need to drive their phy via the generic
phylib framework. Let's reflect that dependency in Kconfig, so that we
don't get build errors when phylib does not get selected.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In the efi_loader main loop we call eth_rx() occasionally. This rx function
might end up calling into devices that haven't been initialized yet,
potentially resulting in a lot of transfer timeouts.
Instead, let's make sure the ethernet device is actually initialized before
reading from or writing to it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The "net_try_count" counter starts from "1".
And the "retrycnt" contains requested amount of retries.
With current logic, that means that the actual retry amount
will be one time less then what we set in "netretry" env.
For example setting "netretry" to "once" will make "retrycnt"
equal "1", so no retries will be triggered at all.
Fix the logic by changing the statement of "if" condition.
Signed-off-by: Leonid Iziumtsev <leonid.iziumtsev@se.atlascopco.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current Cortina phy driver assumes that firmware upload
is required during initialization and is dependent
on presence of corresponding macros like CONFIG_CORTINA_FW_ADDR
for compilation.
But Cortina phy has provision to store phy firmware in
attached dedicated EEPROM. And boards designed with such
EEPROM does not require firmware upload.
Add CORTINA_NO_FW_UPLOAD option in cortina.c to support
such boards.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update get_phy_id() implementation in cortina.c to check
for Cortina_phy by comparing device phy_id with cortina phy_id
instead of relying on presence of CORTINA macros.
This will allow get_phy_id to work with non-cortina phy devices
which might have same phy address as Cortina device but on
different bus.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
1. Set AWCACHE0 attribute of PFE DDR and HDBUS master interfaces
to bufferable.
2. Set RD/WR QoS for PFE DDR and HDBUS AXI master interfaces.
3. Disable ECC detection for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SoC specific PFE macros are defined and structure ccsr_scfg
is updated with members defined for PFE.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
pfe_command provides command line support for several features that
support pfe, like starting or stopping the pfe, checking the health
of the processor engines and checking status of different units inside
pfe.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds PFE driver to U-Boot
Following are the main driver files:-
pfe_hw.c: provides low level helper functions to initialize PFE
internal processor engines and other hardware blocks
pfe_driver.c: provides initialization functions
and packet send and receive functions
pfe_eth.c: provides high level gemac initialization functions
pfe_firmware.c: provides functions to load firmware into PFE
internal processor engines.
pfe_mdio.c: provides functions to initialize phy and mdio.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With CONFIG_DM_ETH enabled, aquantia driver compilation fails with
below error. This patch fixes the issue by including dm.h.
drivers/net/phy/aquantia.c: In function ‘aquantia_startup’:
drivers/net/phy/aquantia.c:73:21: error: dereferencing pointer to
incomplete
type ‘struct udevice’
phydev->dev->name);
^~
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
After allocating plat the pointer is checked.
Afterwards name is allocated and not checked.
Add the missing check to avoid a possible NULL dereference.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Pine64+ uses a generic PHY driver, so flip it over to using the
Realtek PHY driver to actually apply the RTL8211e fix.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Setting PHY_RTL8211E_PINE64_GIGABIT_FIX forces internal rx/tx delays off
on the PHY, as well as flipping some magical undocumented bits. The
magic number comes from the Pine64 engineering team, presumably as a
proxy from Realtek. This configuration fixes the throughput on some
Pine64 models. Packet loss of up to 60-70% has been observed without
this.
Signed-off-by: Kyle Evans <kevans@FreeBSD.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current DW SPI driver uses 32 bit access for some registers and
16 bit access for others. So if DW SPI IP is connected via bus
which doesn't support 16 bit access we will get bus error.
Fix that by switching to 32 bit access only instead of 16 and 32 bit mix
Additional Documentation to Support this Change:
The DW_apb_ssi databook states:
"All registers in the DW_apb_ssi are addressed at 32-bit boundaries
to remain consistent with the AHB bus. Where the physical size of
any register is less than 32-bits wide, the upper unused bits of
the 32-bit boundary are reserved. Writing to these bits has no
effect; reading from these bits returns 0." [1]
[1] Section 6.1 of dw_apb_ssi.pdf (version 3.22a)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
DW SPI internal chip select management has limitation:
it hold CS line in active state only when the FIFO is not
empty. If the FIFO freed before we add new data the SPI transaction will
be broken.
So add option to use external gpio for chip select. Gpio can be added
via device tree using standard gpio bindings.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
There is no sense in waiting for RX data in dw_reader function:
there is no chance that RX data will appear in RX FIFO if
RX FIFO is empty after previous TX write in dw_writer function.
So get rid of this waiting. After that we can get rid of dw_reader
return value and make it returning void. After that we can get rid
of dw_reader return value check in poll_transfer function.
With these changes we're getting closer to Linux DW SPI driver.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In current implementation we get -ETIMEDOUT error when we try to use
transmit only mode (SPI_TMOD_TO)
This happens because in transmit only mode input FIFO never gets any data
which breaks our logic in dw_reader(): we are waiting until RX data will be
ready in dw_reader, but this newer happens, so we return with error.
Fix that by using SPI_TMOD_TR instead of SPI_TMOD_TO which allows to use
RX FIFO.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In current implementation if some data still exists in Tx FIFO it
can be silently flushed, i.e. dropped on disabling of the controller,
which happens when writing 0 to DW_SPI_SSIENR (it happens in the
beginning of new transfer)
So add wait for current transmit operation to complete to be sure
that current transmit operation is finished before new one.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add a generic function which can be used to compute the CRC32 value of
a region of RAM.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
As opposed to PATH, HOSTNAME is not appended to PYTHONPATH
automatically. Lets add it to the examples to make it more
obvious to new users.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Fix a minor typo causing vim (and possibly other) to get confused with
coloring.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Make sure 0x00 is a valid address to read to. If `addr` is 0x00 then
map_physmem() will return 0 which should be a valid address.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Make sure the user is notified instead of silently returning an error.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The kwboot tool for Marvell devices isn't currently being built even if
HOST_TOOLS_ALL is set. It doesn't appear to depend on any CONFIG_
options, so it seems appropriate to enable building it here.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
If we check an index against array bounds, we should do so before
accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add missing cache cleanup before cache disable:
* Flush and invalidate L1 D$ before disabling. Flush and invalidate
SLC before L1 D$ disabling (as it will be bypassed for data)
Otherwise we can lose some data when we disable L1 D$ if this data
isn't flushed to next level cache. Or we can get wrong data if L1 D$
has some entries after enable which we modified when the L1 D$ was
disabled.
* Invalidate L1 I$ before disabling. Otherwise we can execute wrong
instructions after L1 I$ enable if we modified any code when
L1 I$ was disabled.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add additional cache configuration checks and note about
supported configurations.
It is unlikely to face some configuration in real life but
it's better to be prepared and refuse to work on those.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Implement specialized function to clenup caches (and therefore
sync instruction and data caches) which can be used for cleanup before linux
launch or to sync caches during U-Boot self-relocation.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
If L1 D$ is disabled SLC is bypassed for data and all
load/store requests are sent directly to main memory.
If L1 I$ is disabled SLC is NOT bypassed for instructions
and all instruction requests are fetched through SLC.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Implement icache_enabled() and dcache_enabled() as separate functions
which can be used with "inline" attribute. This is a preparation to
make them always_inline.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Move check for PAE existence into slc_upper_region_init()
instead of its caller as more appropriate place.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There is a problem with current implementation if we start U-Boot
from ROM, as we use global variables before ther initialization,
so these variables get overwritten when we copy .data section
from ROM.
Instead we move these global variables into our "global data"
structure so that we may really start from ROM.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
There is a problem with current implementation if we start U-Boot
from ROM, as we use global variables before ther initialization,
so these variables get overwritten when we copy .data section
from ROM.
Instead we'll use icache_exists(), dcache_exists(), slc_exists(), pae_exists()
functions which directly check BCRs every time.
In U-Boot case ops are used only during self-relocation and DMA
so we shouldn't be hit by noticeable performance degradation.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of today we check SLC status before each call of __slc_rgn_op()
or __slc_entire_op(). So move status check into __slc_rgn_op()
and __slc_entire_op().
As we need to check status before *each* function execution and we
call slc_entire_op() and slc_rgn_op() from different places we add
this check directly into SLC entire/line functions instead of
their callers to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Use is_isa_arcv2() function where it is possible instead of
CONFIG_ISA_ARCV2 define check to make code cleaner at the same time
keeping pretty much the same functionality - code in branches
under "if (is_isa_arcv2())" won't be compiled if CONFIG_ISA_ARCV2
is not defined, still we need a couple of CONFIG_ISA_ARCV2
ifdefs to make compiler happy. That's because code in
!is_isa_x() branch gets compiled and only then gets optimized
away.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As we are planning to get rid of dozens of ifdef's in cache.c we
would better check D$ status before each entire/line operation
then check CONFIG_SYS_DCACHE_OFF config option.
This makes the code cleaner as well as D$ entire/line functions
remain functional even if we enable or disable D$ in run-time.
As we need to check status before *each* function execution and we
call D$ entire/line functions from different places we add
this check directly into D$ entire/line functions instead of
their callers to avoid code duplication.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We're starting to use more and more BCRs and having their
definitions in-lined in sources becomes a bit annoying
so we move it all to a separate header.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Move IOC initialization from cache_init() to a separate function.
This is the preparation for the next patch where we'll switch
to is_isa_arcv2() function usage instead of "CONFIG_ISA_ARCV2"
ifdef.
Also it makes cache_init function a bit cleaner.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We don't implement separate flush_dcache_all() intentionally as
entire data cache invalidation is dangerous operation even if we flush
data cache right before invalidation.
There is the real example:
We may get stuck in the following code if we store any context (like
BLINK register) on stack in invalidate_dcache_all() function.
BLINK register is the register where return address is automatically saved
when we do function call with instructions like 'bl'.
void flush_dcache_all() {
__dc_entire_op(OP_FLUSH);
// Other code //
}
void invalidate_dcache_all() {
__dc_entire_op(OP_INV);
// Other code //
}
void foo(void) {
flush_dcache_all();
invalidate_dcache_all();
}
Now let's see what really happens during that code execution:
foo()
|->> call flush_dcache_all
[return address is saved to BLINK register]
[push BLINK] (save to stack) ![point 1]
|->> call __dc_entire_op(OP_FLUSH)
[return address is saved to BLINK register]
[flush L1 D$]
return [jump to BLINK]
<<------
[other flush_dcache_all code]
[pop BLINK] (get from stack)
return [jump to BLINK]
<<------
|->> call invalidate_dcache_all
[return address is saved to BLINK register]
[push BLINK] (save to stack) ![point 2]
|->> call __dc_entire_op(OP_FLUSH)
[return address is saved to BLINK register]
[invalidate L1 D$] ![point 3]
// Oops!!!
// We lose return address from invalidate_dcache_all function:
// we save it to stack and invalidate L1 D$ after that!
return [jump to BLINK]
<<------
[other invalidate_dcache_all code]
[pop BLINK] (get from stack)
// we don't have this data in L1 dcache as we invalidated it in [point 3]
// so we get it from next memory level (for example DDR memory)
// but in the memory we have value which we save in [point 1], which
// is return address from flush_dcache_all function (instead of
// address from current invalidate_dcache_all function which we
// saved in [point 2] !)
return [jump to BLINK]
<<------
// As BLINK points to invalidate_dcache_all, we call it again and
// loop forever.
Fortunately we may do flush and invalidation of D$ with a single one
instruction which automatically mitigates a situation described above.
And because invalidate_dcache_all() isn't used in common U-Boot code we
implement "flush and invalidate dcache all" instead.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Introduce is_isa_arcv2() and is_isa_arcompact() functions.
These functions only check configuration options and return
compile-time constant so they can be used instead of #ifdef's to
to write cleaner code.
Now we can write:
-------------->8---------------
if (is_isa_arcv2())
ioc_configure();
-------------->8---------------
instead of:
-------------->8---------------
ifdef CONFIG_ISA_ARCV2
ioc_configure();
endif
-------------->8---------------
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As of today __dc_line_op() and __dc_entire_op() support
only separate flush (OP_FLUSH) and invalidate (OP_INV) operations.
Add support of combined flush and invalidate (OP_FLUSH_N_INV)
operation which we planing to use in subsequent patches.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
__cache_line_loop() function was copied from Linux kernel
where per-line instruction cache operations are really used.
In U-Boot we use only entire I$ ops, so we can drop support of
per-line I$ ops from __cache_line_loop() because __cache_line_loop()
is never called with OP_INV_IC parameter.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Move instruction cache entire operation to a separate function
because we are planing to use it in other places like
sync_icache_dcache_all().
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We improve on 2 things:
1. Only ARC HS family has "dmb" instructions so do compile-time
check for automatically defined macro __ARCHS__.
Previous check for ARCv2 ISA was not good enough because ARC EM
family is v2 ISA as well but still "dmb" instaruction is not
supported in EM family.
2. Still if there's no dedicated instruction for memory barrier
let's at least insert compile-time barrier to make sure
compiler deosn't reorder critical memory operations.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Disabling relocation might be useful on ARC for 2 reasons:
a) For advanced debugging with Synopsys proprietary MetaWare debugger
which is capable of accessing much more specific hardware resources
compared to gdb. For example it may show contents of L1 and L2 caches,
internal states of some hardware blocks etc.
But on the downside MetaWare debugger still cannot work with PIE.
Even though that limitation could be work-arounded with change of ELF's
header and stripping down all debug info but with it we won't have
debug info for source-level debugging which is quite inconvenient.
b) Some platforms which might benefit from usage of U-Boot basically
don't have enough RAM to accommodate relocation of U-Boot so we
keep code in flash and use as much of RAM as possible for more
interesting things.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Finally GCC's garbage collector works on ARC so let's use it.
That's what I may see for HSDK:
Before:
text data bss dec hex filename
290153 10068 222616 522837 7fa55 u-boot
After:
text data bss dec hex filename
261999 9460 222360 493819 788fb u-boot
Overall ~5% of memory footprint saved.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This commit basically reverts two commits:
1. cf628f772e ("arc: arcv1: Disable master/slave check")
2. 6cba327bd9 ("arcv2: Halt non-master cores")
With mentioned commits in-place we experience more trouble than
benefits. In case of SMP Linux kernel this is really required as
we have all the cores running from the very beginning and then we
need to allow master core to do some preparatory work while slaves
are not getting in the way.
In case of U-Boot we:
a) Don't really run more than 1 core in parallel
b) We may use whatever core for that
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
U-Boot is a bit special piese of software because it is being
only executed once on power-on as compared to operating system
for example. That's why we don't care much about performance
optimizations instead we're more concerned about size. And up-to-date
compilers might produce much smaller code compared to
performance-optimized routines copy-pasted from the Linux kernel.
Here's an example:
------------------------------->8--------------------------
--- size_asm_strings.txt
+++ size_c_strings.txt
@@ -1,2 +1,2 @@
text data bss dec hex filename
- 121260 3784 3308 128352 1f560 u-boot
+ 120448 3784 3308 127540 1f234 u-boot
------------------------------->8--------------------------
See we were able to shave off ~800 bytes of .text section.
Also usage of string routines implemented in C gives us an ability
to support more HW flavors for free: generated instructions will match
our target as long as correct compiler option is used.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Fix NOR, SD and QSPI fallback option in case of secure boot failure.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds a new type IH_OS_TEE. This new OS type will be used for
chain-loading to Linux via a TEE.
With this patch in-place you can generate a bootable OPTEE image like this:
mkimage -A arm -T kernel -O tee -C none -d tee.bin uTee.optee
where "tee.bin" is the input binary prefixed with an OPTEE header and
uTee.optee is the output prefixed with a u-boot wrapper header.
This image type "-T kernel -O tee" is differentiated from the existing
IH_TYPE_TEE "-T tee" in that the IH_TYPE is installed by u-boot (flow
control returns to u-boot) whereas for the new IH_OS_TEE control passes to
the OPTEE firmware and the firmware chainloads onto Linux.
Andrew Davis gave the following ASCII diagram:
IH_OS_TEE: (mkimage -T kernel -O tee)
Non-Secure Secure
BootROM
|
-------------
|
v
SPL
|
v
U-Boot ------>
<----- OP-TEE
|
V
Linux
IH_TYPE_TEE: (mkimage -T tee)
Non-Secure Secure
BootROM
|
-------------
|
v
SPL ------->
<----- OP-TEE
|
v
U-Boot
|
V
Linux
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Andrew F. Davis <afd@ti.com>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Link: http://mrvan.github.io/optee-imx6ul
CONFIG_OPTEE_LOAD_ADDR is used to tell u-boot where to load the OPTEE
binary into memory prior to handing off control to OPTEE.
We need to pull this value out of u-boot in order to produce an IMX IVT/CSF
signed pair for the purposes of secure boot. The best way to do that is to
have CONFIG_OPTEE_LOAD_ADDR appear in u-boot.cfg.
Adding new CONFIG entires to u-boot should be kconfig driven so this patch
does just that.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
OPTEE is currently linked to a specific area of memory called the TrustZone
DRAM. This patch adds a CONFIG entry for the default address of TrustZone
DRAM that a board-port can over-ride. The region that U-Boot sets aside for
the OPTEE run-time should be verified before attempting to hand off to the
OPTEE run-time. Each board-port should carefully ensure that the TZDRAM
address specified in the OPTEE build and the TZDRAM address specified in
U-Boot match-up.
Further patches will use TZDRAM address with other defines and variables to
carry out a degree of automated verification in U-Boot prior to trying to
boot an OPTEE image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
OPTEE is currently linked to a specific area of memory called the TrustZone
DRAM. This patch adds a CONFIG entry for the default size of TrustZone DRAM
that a board-port can over-ride. The region that U-Boot sets aside for the
OPTEE run-time should be verified before attempting to hand off to the
OPTEE run-time. Each board-port should carefully ensure that the TZDRAM
size specified in the OPTEE build and the TZDRAM size specified in U-Boot
match-up.
Further patches will use TZDRAM size with other defines and variables to
carry out a degree of automated verification in U-Boot prior to trying to
boot an OPTEE image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
This patch adds code to lib to enable sharing of useful OPTEE code between
board-ports and architectures. The code on lib/optee/optee.c comes from the
TI omap2 port. Eventually the OMAP2 code will be patched to include the
shared code. The intention here is to add more useful OPTEE specific code
as more functionality gets added.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Harinarayan Bhatta <harinarayan@ti.com>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
ppc4xx support was removed some time ago. Lets remove the now unused
entry in MAINTAINERS as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
ppc4xx support was removed some time ago. Lets remove the now unused
"pci_fb" variable from "struct pci_controller" as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
ppc4xx support was removed some time ago. Lets remove the now unused
NAND driver and all its references for this platform as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Scott Wood <oss@buserror.net>
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add minimal devicetree for STM32MP157C-ED1 board,
with only the devices to allow boot from SDCARD:
- RCC for clock and reset
- UART4 for console
- I2C and PMIC
- DDR
- SDMMC0 for SDCard
Waiting Kernel upstream for alignment.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
add RCC clock driver for STMP32MP157
- base on driver model = UCLASS_CLK
- support ops to enable, disable and get rate
of all SOC clock needed by U-Boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add the 2 new compatible used by STM32MP157
"st,stm32mp157-pinctrl"
"st,stm32mp157-z-pinctrl"
- update the mask for the port
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This driver implements register read/write operations for STPMU1.
The STPMU1 PMIC provides 4 BUCKs, 6 LDOs, 1 VREF
and 2 power switches. It is accessed via an I2C interface.
This device is used with STM32MP1 SoCs.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Kmalloc is using memalign allocation function. It is not necessary to
align this structure so to save bytes, we move to calloc.
And kmalloc function can't be used in SPL early stage (in board_init_f())
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The current value timer_rate_hz causes a problem with function
timer_get_us() from lib time and then an issue with
readx_poll_timeout() function.
With corrected value for tbclk() = timer_rate_hz = CONFIG_SYS_HZ_CLOCK
the weak functions in lib timer can be used:
- get_timer()
- __udelay()
So the specific function in this file are removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add option to include RESET driver and uclass in SPL.
That can be useful to handle IP reset with same driver
in U-Boot and in SPL.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
STM32MP157 bootrom needs a specific header for first boot stage.
This patch adds support of this header in mkimage.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
If the U-Boot environment is stored in a regular file and redundant
operation isn't set, then write to a temporary file and perform an
atomic rename.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Extract write path of flash_io() into a separate function. This patch
should be a functional no-op.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Pass tools/env/fw_env.c through indent to correct style violations. This
commit consists of only one non-whitespace change:
tools/env/fw_env.c:549: error: do not use assignment in if condition
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
U-boot proper signature is not verified by SPL on most platforms
even config SPL_FIT_SIGNATURE is enabled. Only fsl-layerscape
platform support secure boot in platform specific code. So
verified boot cannot be achieved if u-boot proper is loaded by
SPL.
This patch add signature verification to u-boot proper images
when loading FIT image in SPL. It is tested on Allwinner bananapi
zero board with H2+ SoC.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Add proper and simple kconfig option for dram_sun8i_a83t.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a33.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add proper and simple kconfig option for dram_sun8i_a23.c
instead of using MACH type on Makefile.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Add simple and meaningful kconfig option for prcm.c
instead of using MACH type on Makefile.
PRCM (Power/Reset/Clock Management) is considered as a
Multi-Functional Device, so used the same on Kconfig definition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Enable the display controller, panel & backlight.
Set panel display timings & set the RGB data bus.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
This patch increases timeout to 2s.
It was seen on 2 USB devices (Verbatim STORE N GO 070B4AED0FB22358 and
USB DISK 2.0 9000729BA41DDF40) that the request sense command takes
between 1.3s and and 1.5s.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds an interface to disable the power in dwc2 driver.
This new interface is called when the device is removed.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add generic_phy_power_on() and generic_phy_power_off()
calls to switch ON/OFF phy during probe and remove functions.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
ppc4xx support was removed some time ago. Lets remove the now unused
EHCI driver and all its references for this platform as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Marek Vasut <marex@denx.de>
DWC3 USB3 controllers will need USB3 PHY to be enabled, in addition to
USB2 PHY, to be functional. Therefore enable USB3 PHY when available.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Refractor PHY get/init/poweron and PHY poweroff/exit operations into
separate function so that its easy to support multiple PHYs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
It is wrong that expect .phy_init() to also power on the PHY. Therefore,
explicitly, call generic_phy_power_on() after generic_phy_power_init() in
order to power on PHY before using it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If we use hardware with very small RAM (let's consider just a couple
of hundreds of kB but not megabytes) it is not super convenient to lose
64kB for statically allocated bufer which most probably won't be used
as big as it is. Typically we'll have much shorter data packages to
excahnge and in the worst case longer packets will be split on separate
transactions.
For those corner-cases user will be able to set his buffer size of
choice via USB_DWC2_BUFFER_SIZE option in menuconfig.
By default we'll use 64 kB as it was hard-coeded before so existing
users shouldn't be affected at all.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Merge init_helpers.h in the new file init.h
with only prototypes for init_cache_f_r
used in common/board_f.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Move prototypes for function used in common/board_f.c
from common.h to init.h
Remove weak for arch_reserve_stacks in prototype
(checkpatch issue)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This file is completely unused and it should be removed as the part of
ppc405/ppc440 xilinx platform removal.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Change due to commit b08c8c4870 ("libfdt: move headers to
<linux/libfdt.h> and <linux/libfdt_env.h>")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
arch/arm/cpu/armv7/mx*/ does not relate to any existing directory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The 2 functions board_power_mode and board_poweroff
are no more existing in U-Boot code (check with grep)
This patch updates the documentation and removes
the unnecessary prototypes.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove the prototypes for 4 functions no more existing
in U-Boot code (checked by grep):
- checkflash
- checkdram
- mdm_init
- setup_board_extra
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a new file init.h with the prototype for arch_cpu_init
Add a prototype for mach_cpu_init() to avoid a warning:
no previous prototype for ‘mach_cpu_init’
It is a first step to move all the functions prototype
used during U-Boot initialization (board_f.c / board_r.c)
from common.h to init.h
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Due to adding various new functionalities with SPI and SPI-FLASH
subsystems which are rounding in Mailing list for year these long
term supporting spi driver which never seen any update with
driver-model conversion.
So added migration plan for DM_SPI and DM_SPI_FLASH with
deadline v2018.09
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Adds a dedicated defconfig to build TI K2L secure
devices and updates MAINTAINERS.
k2l_hs_evm_defconfig is created from the k2l_evm_defconfig
and removes support for SPL, as SPL is not supported on K2
HS devices. Corrects SYS_TEXT_BASE for HS devices.
Also adds TI_SECURE_DEVICE and FIT_IMAGE_POST_PROCESS to
include support for secure image creation and authentication
Signed-off-by: Madan Srinivas <madans@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Andrew F. Davis <afd@ti.com>
This patch updates the default u-boot env for K2L HS devices
to install the secure boot monitor and load the fitImage during
boot.
Signed-off-by: Madan Srinivas <madans@ti.com>
Acked-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Remove busy looping during watchdog reset.
Each polling of W_PEND_WTGR bit ("finish posted
write") after watchdog reset takes 120-140us
on BeagleBone Black board. Current U-Boot code
has watchdog resets in random places and often
there is situation when watchdog is reset
few times in a row in nested functions.
This adds extra delays and slows the whole system.
Instead of polling W_PEND_WTGR bit, we skip
watchdog reset if the bit is set. Anyway, watchdog
is in the middle of reset *right now*, so we can
just return.
This noticeably increases performance of the
system. Below are some measurements on BBB:
- DFU upload over USB 15% faster
- fastboot image upload 3x times faster
- USB ep0 transfers with 4k packets 20% faster
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
As said in the SAMA5D2 datasheet, the PLLA clock must be divided
by 2 by writing the PLLADIV2 bit in PMC_MCKR, if the ratio between
PCK and MCK is 3 (MDIV = 3). This is the purpose of the driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The kernel size is getting bigger and bigger. Because the Android
common kernel is even bigger than the vanilla one, so images overlap
in the current memory layout.
Adjust the load address for a bigger kernel image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If a bigger EL32 is used, fip.bin can be larger than the currently
assumed boot firmware size. Adjust the update commands.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
With the introduction of ("Boards,Need,to,Switch,DM] spi: omap3_spi:
Full dm conversion"), Driver Model for McSPI is now available on the
omap3. This enables the config by default on omap3_logic boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
omap3_spi_set_speed|mode redeclared bus symbol, fix the same.
error:
drivers/spi/omap3_spi.c: In function ‘omap3_spi_set_speed’:
drivers/spi/omap3_spi.c:650:18: error: ‘bus’ redeclared as different kind of symbol
struct udevice *bus = dev->parent;
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 278b90ce78 ("configs: Migrate CONFIG_SYS_TEXT_BASE") made
CONFIG_SYS_TEXT_BASE a proper Kconfig variable, with the consequence
of moving the common definition shared by almost every sunxi board
into 123 individual defconfig files. But the U-Boot start address
for Allwinner boards is a platform decision which has been around for
ages, so defining it in each *board* config file seems a bit over the
top.
Define the standard values (160MB into DRAM for most SoCs, with two
SoC exceptions) if ARCH_SUNXI is selected, and delete the lines from
the individual defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For the last return of function get_ram_size(),
when size=maxsize, restore the base address (*base)
content.
Add comment for the remaining case to avoid regression:
this case is already correctly handled.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Save the content of the base address in a new variable
in stack (save_base) to prepare restore this content.
This patch don't modified code behavior and stack usage.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When enabling CONFIG_FASTBOOT_FLASH in am335x_boneblack_defconfig, next
build errors and warnings occur:
arch/arm/mach-omap2/utils.c: In function ‘omap_set_fastboot_cpu’:
arch/arm/mach-omap2/utils.c:26:16: warning: implicit declaration of
function ‘omap_revision’ [-Wimplicit-function-declaration]
u32 cpu_rev = omap_revision();
^~~~~~~~~~~~~
arch/arm/mach-omap2/utils.c:29:7: error: ‘DRA762_ES1_0’ undeclared
(first use in this function)
Include asm/omap_common.h explicitly to avoid those.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Acked-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The SPL can't use high speed MMC modes if the associated pinctrl and
IOdelays are described in the DTS.
Make them available in SPL by tagging the nodes with 'u-boot,dm-spl;'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Beside enabling the support for HS200 in mmc core, enabling the HS200
support in the SPL requires multi-dtb support in the SPL because pinctrl
and IOdelays vary across SOCs.
Also we need to make sure that the pinctrl properties arenot removed from
the dts by setting CONFIG_OF_SPL_REMOVE_PROPS to remove only clocks and
interrupts properties.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Now that we have a device-tree include file with common
MMC/SD IOdelay data for DRA76x SoC, shift the EVM device-tree
file to using that.
Also fix the name of the IO voltage regulator for mmc1.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a common device-tree include file with MMC/SD IOdelay data
for DRA76x SoC based on the linux DTSI file.
In the most common case, IOdelay data available in datamanual
can directly be used. This file caters to that common case.
Data is based on DRA76x datamanual, SPRS993A, revised July 2017.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This commit does the following for OMAP3 EVM:
- Track omap3_beagle changes where possible
- Remove CONFIG_SYS_MPUCLK and CONFIG_MTD which are not needed for the
default board configuration to work.
- Remove CONFIG_SPL_SYS_MALLOC_SIMPLE and CONFIG_SYS_MALLOC_F_LEN from
default config. CONFIG_SYS_MALLOC_F_LEN=0x400 is set by configuration
automatically. [allows board to boot with SERIAL_SEARCH_ALL=y]
- Use updated NAND layout:
device nand0 <omap2-nand.0>, # parts = 6
#: name size offset
-------------------------------------------------
0: spl 0x00080000(512k) 0x00000000
1: u-boot 0x001e0000(1920k) 0x00080000
2: u-boot-env 0x00020000(128k) 0x00260000
3: dtb 0x00020000(128k) 0x00280000
4: kernel 0x00600000(6m) 0x002a0000
5: rootfs 0x0f760000(-) 0x008a0000
-------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This commit does the following for BeagleBoard{-xM}:
- Enable DM_SERIAL which also enables SPL_DM_SERIAL
- Misc. config updates in support of DM_SERIAL
- Use updated NAND layout (BeagleBoard):
device nand0 <omap2-nand.0>, # parts = 6
#: name size offset
-------------------------------------------------
0: spl 0x00080000(512k) 0x00000000
1: u-boot 0x001e0000(1920k) 0x00080000
2: u-boot-env 0x00020000(128k) 0x00260000
3: dtb 0x00020000(128k) 0x00280000
4: kernel 0x00600000(6m) 0x002a0000
5: rootfs 0x0f760000(-) 0x008a0000
-------------------------------------------------
- Use MMC and UBIFS support from config_distro_bootcmd.h
- Use LEGACY_MMC and NAND support defined in omap3_beagle.h
[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-fat
label omap3-beagle-mmc-fat
kernel /zImage
fdt /omap3-beagle.dtb
append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[LEGACY_MMC(0:2)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-mmc-ext4
label omap3-beagle-mmc-ext4
kernel /boot/zImage
fdt /boot/omap3-beagle.dtb
append console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
[UBIFS(ubi0:rootfs)/boot/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-beagle-nand-ubifs
label omap3-beagle-nand-ubifs
kernel /boot/zImage
fdt /boot/omap3-beagle.dtb
append console=ttyO2,115200n8 root=ubi0:rootfs rw ubi.mtd=rootfs rootfstype=ubifs rootwait
---8<-------------------------------------------------------------------
The board's 'bootcmd' can also be overridden with:
CONFIG_BOOTCOMMAND="run findfdt; run mmcboot"
CONFIG_BOOTCOMMAND="run findfdt; run nandboot"
CONFIG_BOOTCOMMAND="run findfdt; run ramboot"
or
CONFIG_BOOTCOMMAND="run findfdt; run somethingelse"
The use of 'run findfdt' is required.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Get the start address and the size of partitions using partition names
rather than partition numbers. This way we can change the partition
table further without changing the boot code.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Refactor the code for "part start" and "part size" commands to avoid
code duplication.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Allow passing the partition name to "part start" and "part size"
commands, so we can avoid magic numbers in the environment.
Consider one real use-case: in include/environment/ti/boot.h we have
commands like these:
setenv boot_part 9
part start mmc ${mmcdev} ${boot_part} boot_start
part size mmc ${mmcdev} ${boot_part} boot_size
mmc read ${loadaddr} ${boot_start} ${boot_size}
Now suppose that we have changed the partition table and boot_part now
is 10. We will need to fix commands above. And anyone who relies on
these boot commands, will need to change them accordingly, too (this was
an actual case in our lab while testing Linux boot on Android
environment).
By providing the option to pass partition name instead, we fix mentioned
issue, by eliminating the necessity to use magic numbers.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Currently, if a test emits a warning message but otherwise passes, there's
no indication of this in the log summary, which can lead to warnings being
missed. Enhance the test logic to explicitly mention warnings in otherwise
passing tests, and not to collapse the log sections for tests with
warnings, so that they're more easily seen when scanning the log.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add a standalone MMC block read test. This allows direct testing of MMC
access rather than relying on doing so as a side-effect of e.g. DFU or
UMS testing, which may not be enabled on all platforms.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Do not need to scan disk every time when we get part info
by name.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[trini: Fix build in !CONFIG_HAVE_BLOCK_DEVICE case]
Signed-off-by: Tom Rini <trini@konsulko.com>
If a DUT do not have partition table, and we write one with 'gpt write'
cmd, we should able to list the partition with 'part list' cmd.
It's reasonable to scan the disk again if the initial part_type is
unknown in case we just write a new one into disk.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
On linux kernel side, on STM32F7 and STM32H7 SoCs, DMA requires
uncachable regions. These regions are defined in DT.
Since kernel linux v4.15, on ARMv7-M Cortex, kernel is able
to configure MPU regions depending on DT settings.
As kernel is able to configure MPU, this allows to remove
MPU region settings in bootloader.
On Cortex M processors, MPU allows to use a default memory map.
(see B3.5.4 MPU Control Register, MPU_CTRL in
https://developer.arm.com/products/architecture/m-profile/docs/ddi0403/latest/armv7-m-architecture-reference-manual)
Use the default memory map as background region for all STM32 SoCs
family with an additional MPU region corresponding to the SDRAM area.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable DOS_PARTITION for boards STM32F429-eval, STM32F469-disco
and STM32F746-disco.
This allows to read FAT partition on mmc.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This board offers:
_ STM32F746NGH6 microcontroller with 1 Mbyte Flash and 320+4 Kbytes RAM
_ Six 5 V power supply options:
Power jack
ST-LINK/V2-1 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with microphone
_ Stereo digital microphone, audio jack connector used to connect
external speakers
_ 2 Gbytes (or more) SDMMC interface microSD card
_ RF-EEPROM on I2C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2-1 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8Mx32 bit SDRAM, 1Mx16 bit SRAM & 8Mx16 bit Nor Flash
_ 512 Mbits QuadSPI Nor Flash
_ 5.7 inch 640x480 pixel TFT color LCD with capacitive touch panel
_ Joystick with 4-direction control and selector
_ Reset, WakeUp/Tamper or key button
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN 2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
More detailed information are available here :
http://www.st.com/en/evaluation-tools/stm32746g-eval.html
To compile stm32f746-eval board, use same defconfig as
stm32f746-disco, the only difference is to pass
"DEVICE_TREE=stm32746g-eval".
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For STM32F4 and F7 SoCx family, a specific stm32.h file exists.
Some common defines are duplicated or even unused in each of
these stm32.h.
Factorize all common definition in arch/arm/include/asm/stm32f.h and keep
specific definitions in each arch/arm/include/asm/arch-stm32fx/stm32.h.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Instead to have 3 identical gpio.h for all STM32 SoCs,
migrate them in one file in include/asm.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
fmc.h file is no more used, remove it.
All FMC related defines are declared in drivers/ram/stm32_sdram.c
which is common to all STM32 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This avoids the following errors while reading on mmc:
Read data bytes CRC error: 0x2
switch to partitions #0, OK
mmc0 is current device
Read data bytes CRC error: 0x82002
** Unrecognized filesystem type **
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
DSI clock is available on STM32F769-disco and
STM32F469-disco board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Implement set_rate() for LTDC clock only, set_rate for other
clocks will be added if needed. This is needed by future LTDC driver
improvements.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Configure SAI PLL configuration to generate LTDC pixel clock on
the PLLSAIR output.
PLLSAI is enabled only if CONFIG_VIDEO_STM32 flag is set.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rework the way SDMMC clock get rate is done in a more
generic way :
_ Add stm32_clk_get_pllsai_rate() which give the PLLSAI
indicated output rate.
_ Add stm32_clk_get_pllsai_vco_rate() which give the VCO
internal rate.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Initially, 48Mhz for SDIO clock was generated from SAI pll for
STM32F469 and STM32F746 SoCs, but this solution was not suitable
for STM32F429 SoCs.
A generic solution is to used the PLL_Q output as 48Mhz clock
for all STM32F SOCs family.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Wrong parameter was passed to stm32_clk_pll48clk_rate().
sysclk (PLL_p output value) was passed instead of VCO value.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds "st,pin-ckin" support to activate sdmmc_ckin feature.
When using an external driver (a voltage switch transceiver),
it's advised to select SDMMC_CKIN feedback clock input to sample
the received data.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The hardware flow control functionality is used to avoid
FIFO underrun (TX mode) and overrun (RX mode) errors.
The behavior is to stop SDMMC_CK during data transfer and
freeze the SDMMC state machines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This timer driver is using GPT Timer (General Purpose Timer)
available on all STM32 SOCs family.
This driver can be used on STM32F4/F7 and H7 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add supporting regulators for rk3288-vyasa board, dc12_vbat is
parent regulatorand followed regulators as are child regulators.
regulator naming conversion followed as per schematic for better
readability and easy for identification.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Booting a aarch64 Linux kernel requires the image to be placed
text_offset bytes from a 2MB aligned address.
See https://www.kernel.org/doc/Documentation/arm64/booting.txt
booti_setup() takes care about this alignment and will relocate the
image if not properly aligned with memmove(). This can require up
to double the size of the loaded image and therefore accidentally
overwrite content placed there (i.e ramdisk_addr_r) for large kernel
images.
By adding text_offset to the default kernel_addr_r we can prevent that
from happening for kernels larger 18MB and also save a few cycles.
We can assume a text_offset of 0x80000 for most cases, all others will be
handled by booti_setup() anyway.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CONFIG_PHY_ADDR is used for old-style configuration. This makes
impossible changing the PHY address, if multiple boards share a same
config header file (for example include/configs/sunxi-common.h).
Moving this to Kconfig helps overcoming this issue. It's defined
as entry inside PHYLIB section.
After the implemention, moveconfig was run. The issues are:
- edb9315a - CONFIG_PHYLIB is not enabled. Entry is
deleted.
- ds414 - CONFIG_PHYLIB is in incompatible format:
{ 0x1, 0x0 }. This entry is also deleted.
- devkit3250 - The PHY_ADDR is in hex format (0x1F).
Manually CONFIG_PHY_ADDR=31 is added in
the defconfig.
After the changes the suspicious defconfigs passes building.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The previous code tried to update the PHY parameters without waiting for
autonegotiation to complete. This caused wrong values to be written to
the EMAC in sun8i_adjust_link(). As a result, any commands that called
eth_start() before autonegotiation completed would find the network
nonfunctional. Fix this by using the correct function to start up the
PHY.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With CONFIG_DM_MMC the BananaPi does not detect SD cards.
The sunxi device trees use the cd-inverted property to indicate that
the card detect is inverted.
This property is documented in Linux kernel devicetree/bindings/mmc/mmc.txt
The property is not marked as deprecated.
A similar patch was posted by Tuomas but is in status "Changes Requested".
https://patchwork.ozlabs.org/patch/850377/
This patch is a stripped down version of his patch.
Suggested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When the OTG node was added, its reg property for its address space was
missing. With commit f4f9896ac3 ("musb: sunxi: Use base address from
device tree"), the OTG controller's address is derived from the device
tree exclusively. The missing property results in U-boot crashing when
MUSB is initialized.
Fixes: b0bea66789 ("sunxi: Add USB and R_PIO nodes to sun8i-a83t.dtsi")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
With the merge of the new u-boot.itb size check now the build for
pine64_plus_defconfig breaks, as this file gets too large:
=============
u-boot.itb exceeds file size limit:
limit: 516096 bytes
actual: 521852 bytes
excess: 5756 bytes
make: *** [u-boot.itb] Error 1
=============
One easily fixable reason is that we actually have two .dtbs in our FIT
image, one for the regular Pine64+ board, and one for the non-plus version.
The only difference U-Boot cares about is the 100Mbit Ethernet PHY used
on the non-plus version, however Ethernet isn't enabled in the non-plus
DT anyway.
So we could avoid the non-plus special handling, and remove that extra
.dtb from the FIT image, which saves a few KBs and brings us back below the
limit. The Pine64 would boot with a Pine64+ .dtb, and would fail to
enable Ethernet. Given that it didn't work in the first place, this is not
a regression.
Once we switch to a non-MMC environment, we can bring this back, then
with a proper .dtb and hopefully working Ethernet.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
This SUNXI variant SPL SPI code doesn't use either SPI or
SPL_FLASG subsystems due to size constraints and also placing
this code in drivers/mtd/spi will unnecessary build SPI_FLASH
code(if defined) which never required, hence moved to arch area.
And also renamed the file according to kconfig which resembles
proper name.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
set_mode, set_seed functions has separate function pointers
in dm_spi_ops, so use them in relevent one instead of
calling from claim_bus.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Boards adp-ae3xx_defconfig, nx25-ae250_defconfig
already enabled DM_SPI, so non-dm code make no use
of it hence droped.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
commit 8c4037a09a ("imx: hab: Ensure the IVT DCD pointer is Null prior
to calling HAB authenticate function.") makes the DCD field being NULL a
dependency.
This change though will break loading and executing of existing pre-signed
binaries on a u-boot update i.e. if this change is deployed on a board you
will be forced to redo all images on that board to NULL out the DCD.
There is no prior guidance from NXP that the DCD must be NULL similarly
public guidance on usage of the HAB doesn't call out this NULL dependency
(see boundary devices link).
Since later SoCs will reject a non-NULL DCD there's no reason to make a
NULL DCD a requirement, however if there is an actual dependency for later
SoCs the appropriate fix would be to do SoC version checking.
Earlier SoCs are capable (and happy) to authenticate images with non-NULL
DCDs, we should not be forcing this change on downstream users -
particularly if it means those users now must rewrite their build systems
and/or redeploy signed images in the field.
Fixes: 8c4037a09a ("imx: hab: Ensure the IVT DCD pointer is Null prior
to calling HAB authenticate function.")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Link: https://boundarydevices.com/high-assurance-boot-hab-dummies
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The README.mxc_hab is outdated and need improvements, add the following
modifications:
- Reorganize document and remove duplicate content
- Add CST download link
- Update CST package name
- Align command lines with CST v2.3.3
- Update U-Boot binary name
- Remove CSF padding since is not documented in AN4581
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the High Assurance Boot procedure is documented in two
places:
- doc/README.imx6
- doc/README.mxc_hab
It is better to consolidate all HAB related information into
README.mxc_hab file, so move the content from README.imx6 to
README.mxc_hab.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
commit ed286bc80e ("imx: hab: Check if CSF is valid before authenticating
image") makes use of "__packed" as a prefix to the "struct hab_hdr"
declaration.
With my compiler "gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)" we
get:
./arch/arm/include/asm/mach-imx/hab.h:42:25: error: expected ‘=’, ‘,’, ‘;’,
‘asm’ or ‘__attribute__’ before ‘{’ token
struct __packed hab_hdr {
Fix this problem by including <linux/compiler.h>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch fixes the wrongly included dtsi file which was
breaking mainline support for Engicam i.CoreM6 DualLite/Solo RQS.
Linux commit details for the same change as
"ARM: dts: imx6dl: Include correct dtsi file for Engicam i.CoreM6
DualLite/Solo RQS"
(sha1: c0c6bb2322964bd264b4ddedaa5776f40c709f0c)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
usdhc4 node need to update pinctrl, bus-width and non-removable
properties, sync the same from Linux.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The system call used by mkimage to run dtc redirects stdout to a
temporary file. This can cause problems on Windows (with a MinGW
cross-compiled version). Using the "-o" dtc parameter avoids
this problem.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
kmerr: verify that malloc and calloc are followed by a check to verify
that we are not out of memory.
badzero: Compare pointer-typed values to NULL rather than 0
Both checks are copied from the Linux kernel archive.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Inform the EFI subsystem that the framebuffer memory is reserved.
Without the patch the AllocatePool boot service allocates memory from the
framebuffer which will will be overwritten by screen output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AT91SAM9263EK
CONFIG_AT91SAM9RLEK
CONFIG_BARIX_IPAM390
CONFIG_BOARD_H2200
CONFIG_EP9301
CONFIG_KZM_A9_GT
CONFIG_PICOSAM
CONFIG_PLATINUM_PICON
CONFIG_PLATINUM_TITANIUM
CONFIG_PM9261
CONFIG_PM9263
CONFIG_PM9G45
CONFIG_SIEMENS_DRACO
CONFIG_SIEMENS_PXM2
CONFIG_SIEMENS_RUT
CONFIG_SMDKC100
CONFIG_SMDKV310
CONFIG_STM32F4DISCOVERY
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_ARM926EJS
CONFIG_CPUAT91
CONFIG_EXYNOS5800
CONFIG_SYS_CORTEX_R4
Most of them are config symbols named after the respective SoCs which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_DBAU1X00
CONFIG_PB1X00
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
CONFIG_SYS_CBSIZE determines the maximum length of the kernel command
line, and the default value of 256 is too small for booting some Linux
images in the wild.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Without the volatile attribute, compilers are entitled to optimize out
the same asm(). In the case of __udelay() in syscounter.c, it calls
`get_ticks()` twice, one for the starting time and the second in the
loop to check the current time. When compilers inline `get_ticks()`
they see the same `mrrc` instructions and optimize out the second one.
This leads to infinite loop since we don't get updated value from the
system counter.
Here is a portion of the disassembly of __udelay:
88: 428b cmp r3, r1
8a: f8ce 20a4 str.w r2, [lr, #164] ; 0xa4
8e: bf08 it eq
90: 4282 cmpeq r2, r0
92: f8ce 30a0 str.w r3, [lr, #160] ; 0xa0
96: d3f7 bcc.n 88 <__udelay+0x88>
98: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc}
Note that final jump / loop at 96 to 88, we don't have any `mrrc`.
With a volatile attribute, the above changes to this:
8a: ec53 2f0e mrrc 15, 0, r2, r3, cr14
8e: 42ab cmp r3, r5
90: f8c1 20a4 str.w r2, [r1, #164] ; 0xa4
94: bf08 it eq
96: 42a2 cmpeq r2, r4
98: f8c1 30a0 str.w r3, [r1, #160] ; 0xa0
9c: d3f5 bcc.n 8a <__udelay+0x8a>
9e: e8bd 8cf0 ldmia.w sp!, {r4, r5, r6, r7, sl, fp, pc}
a2: bf00 nop
I'm advised[1] to put volatile on all asm(), so this commit also adds it
to the asm() in timer_init().
[1]: https://lists.denx.de/pipermail/u-boot/2018-March/322062.html
Signed-off-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Sometimes imximage throws the following error:
CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp
CFGS board/freescale/vf610twr/imximage.cfg.cfgtmp
MKIMAGE u-boot-dtb.imx
Error: No BOOT_FROM tag in board/freescale/vf610twr/imximage.cfg.cfgtmp
arch/arm/mach-imx/Makefile💯 recipe for target 'u-boot-dtb.imx' failed
Later on, when running mkimage for the u-boot.imx it will succeed in
finding the IVT offset.
Looks like some race condition happening during parallel build when
processing mkimage for u-boot-dtb.imx and u-boot.imx.
A proper fix still needs to be implemented, but as a workaround let's
remove the error when the IVT offset is not found.
It is useful to have such message, especially during bring-up phase,
but the build error that it causes is severe, so better avoid the
build error for now.
The error checking can be re-implemented later when we have a proper
fix.
Reported-by: Breno Lima <breno.lima@nxp.com>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Support special rendition code 0 - reset attributes.
Support special rendition code 1 - increased intensity (bold).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use constants to refer to colors.
Adjust initialization of foreground and background color to avoid
setting reserved bits.
Consistently u32 instead of unsigned for color bit mask.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In 16 bit mode we have to copy two bytes per pixels repeatedly and not
four. Otherwise we will see a striped pattern.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get RGB sequence in pixels right (swap blue and red).
Do not set reserved bits.
qemu-system-i386 -display sdl -vga virtio and
qemu-system-i386 -display sdl -vga cirrus
now display the similar colors (highlighting still missing) as
qemu-system-i386 -nographic
Testing is possible via
setenv efi_selftest test output
bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Keep spelling.txt in sync with the version from kernel 4.16-rc4.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There are no headers for libfdt in lib/libfdt, as they are instead
located in scripts/dtc/libfdt. Specifying lib/libfdt for headers
inclusion in host tools results in using the system libfdt headers,
which is not what we want. Change this to the proper path.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add a comment indicating that the German key map assumes code page 437.
Add support for character ² (square sign) in the German key map.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The PCA953x driver uses "gpio@%x_" as the GPIO bank name, where "%x" is
instantiated with the I2C address of the chip. While this works, it
becomes very confusing if a board has multiple PCAs with the same
address on different I2C busses, and it also becomes an issue when a
GPIO's value is to be set via the 'gpio' command, because this command
only ever sets the value of the first device it encounters, leaving the
other devices inaccessible to the command.
As to not break boards that rely on this naming scheme, we introduce a
new device tree string property "label" for the driver. If it exists, it
is used to build a bank name of the form "%s@%x_" (where %x is still
instantiated with the I2C address). If it does not exist, the legacy
labeling scheme is used.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Treat the first equal sign as a key/value separation too. This makes
the script files compatible with mkenvimage input file format. It
won't support variables with equal signs anymore, but this seems not
really like a loss.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Ensure that the Atmel TPM driver performs sufficient
validation of the length returned in the TPM response header.
This patch prevents memory corruption if the header contains a
length value that is larger than the destination buffer.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
Ensure that the Infineon I2C and SPI TPM driver performs adequate
validation of the length extracted from the TPM response header.
This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
This patch prevents integer underflow when the length was too small,
which could lead to memory corruption.
Signed-off-by: Jeremy Boone <jeremy.boone@nccgroup.trust>
This patch got dropped during the update of DTs to 4.14, re-add it
back. This adds reset GPIOs to the ethernet PHYs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Xilinx Kconfig changes for v2018.03
- Moving some macros to Kconfig
# gpg: Signature made Thu 01 Mar 2018 10:45:58 AM EST using DSA key ID 294A0C21
# gpg: Good signature from "Michal Simek <monstr@monstr.eu>"
# gpg: aka "Michal Simek (Xilinx) <michals@xilinx.com>"
# gpg: aka "Michal Simek (Xilinx) <michal.simek@xilinx.com>"
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MIN_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_SDHCI_MAX_FREQ
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_I2C0 and
CONFIG_ZYNQ_I2C1 and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SPEED
and set it to default value 100000.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_SYS_I2C_ZYNQ_SLAVE
and set it default to 0.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the
values over to the defconfigs.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
This patch added Kconfig support for FPGA_SPARTAN3 and migrates the
values over to the defconfigs.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Enable networking command only when NET is enabled.
And remove selecting NET for CMD_NET
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The u-boot-elf.srec is needed for the minimon update on Gen3 SoCs,
conveniently generate this file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After commit ba1f966725 ("net: designware: add clock support")
we got NET broken on axs101 and axs103 platforms.
Some clock don't support gating so their clock drivers don't
implement .enable/.disable callbacks. In such case clk_enable
returns -ENOSYS.
Also some clock drivers implement .enable/.disable callbacks not for all
clock IDs and return -ENOSYS (or -ENOTSUPP) for others.
If we have such clock in 'clocks' list of designware ethernet controller
node we fail to probe designware ethernet.
Fix it.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Commit 68e6ecadc5 ("net: phy: marvell 88e151x: Fix handling of RGMII
interface types") fixed the initialization of 88e151x phys, but made it
so that interfaces of type PHY_INTERFACE_MODE_RGMII had both RX and TX
delay bits cleared. The default (like in m88e1111s_config) is to have
both bits set.
Hence, this patch changes the behavior in the PHY_INTERFACE_MODE_RGMII
case so that both bits are set.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix some style violations (mostly wrong indentions) in the Marvell PHY
driver.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
tsec_initialize allocates a private driver structure using malloc.
Should the memory allocation of this private structure fail, the
function execution is aborted with a return 0, but the previously
allocated device structure is never freed, hence leaked.
Free the device structure in the error case.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
mmc_of_parse() doesn't set a default value if none is available in DT.
In that case, use a default 52MHz clock rate.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some platforms don't have ADMA controllers. For those platforms, compiling
it out reduces the size of the binary by about 600 bytes.
Leaving the support in doesn't break things as the driver checks at runtime
if the ADMA2 controller is present.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.
This saves around 740 bytes for the am335x_evm SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Migrate the users of CONFIG_SYS_BOOTCOUNT_ADDR to Kconfig. We can
provide a default for BOOTCOUNT_AM33XX as that's a specific part of the
RTC in use. We can also provide a default for ARCH_LS1043A and
ARCH_LS1021A as they had been previously calculated and their symbols
are in Kconfig. In the case of other QE-enabled platforms, they are not
so we must update the relevant defconfig files. The previous default
only applied in some cases, even on a specific SoC family.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Alex Kiernan <alex.kiernan@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Commit d695d66278 ("spl: eMMC/SD: Provide one __weak spl_boot_mode()
function") breaks the boot on several i.MX6 boards,
such as cuboxi and wandboard:
U-Boot SPL 2018.03-rc1-00212-g48914fc119 (Feb 10 2018 - 11:04:33 +1300)
Trying to boot from MMC1
Failed to mount ext2 filesystem...
spl_load_image_ext: ext4fs mount err - 0
Partially revert it so that we can boot U-Boot again on these
i.MX6 platforms.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
The device-tree node for the PMU clk controller assigns to its parent
(i.e. PLL_PPLL) even though this clock currently is set up statically
by an init-function.
In order to avoid unexpected failures, a simple implementation of
set_rate (which accepts requests, but notifies the caller of the
preset frequency in its return value) and get_rate (which always
returns the preset frequency) are added.
Note that this is required for the RK808 PMIC to probe successfully on
the RK3399-Q7, following the support for the assigned-clocks property.
References: commit f4fcba5c5b ("clk: implement clk_set_defaults()")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
TPL offset 0xff704004 is unaligned address which is adding nearest
8-bytes for next instruction, So 0xff704004 is adding 0x20 for
proper alignment which is causing the next instruction data
0xefffffff is moved.
Hexdump with overlaped bytes:
-----------------------------
0000000 0000 0000 0000 0000 0000 0000 0000 0000
0000010 0000 0000 0000 0000 0000 0000 ffff eaff
So, Fix the TEXT_BASE for proper aligned address 0xff704000
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Due to size limitations in SPL by adding falcon mode,
rk3288 support TPL. In order to not overlap SPL_TEXT_BASE
add TPL_TEXT_BASE with u-boot-tpl.lds that intern call
u-boot-spl.lds with proper TEXT_BASE values.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since commit ba1f966725 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3368 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the RK3368 clk driver to:
(a) provide a enable op
(b) signals success to the caller when the clocks for the GMAC are
enabled (no actual action is necessary as the gates are open
after reset)
References: commit ba1f966725 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Since commit ba1f966725 ("net: designware: add clock support"), the
designware GMAC driver enables all referenced clocks. While this is a
no-op for the RK3399 during boot-up (reset behaviour has all the clock
gates open anyway), we still need to handle the clock-ids passed in
the enable op of the clock-driver and return a success.
This change extends the enable-op of the rk3399 clk driver to signal
success to the caller when the clocks for the GMAC are enabled.
References: commit ba1f966725 ("net: designware: add clock support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
usdhc4 has eMMC on icore-rqs boards, SPL is not detecting
it becuase of u-boot,dm-spl flag so add it to make eMMC working.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tidy up CONFIG_SYS_BOOTCOUNT_SINGLEWORD from the whitelist as there's
no remaining uses of it left.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Make generate boot counter selected in the same way as other boot count
drivers
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_I2C
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_RAM
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_BOOTCOUNT_ENV
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
CONFIG_BOOTCOUNT was only used in mx53ppd, merge it with
CONFIG_BOOTCOUNT_LIMIT
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Ian Ray <ian.ray@ge.com>
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>
The video drivers (VOP, HDMI encoder, LVDS encoder, MIPI encoder) for
Rockchip SOCs are self-contained and are mainly impacted by other
changes in the architecture support (e.g. pinctrl, clocking, etc).
Let's add these to the list of files maintained as part of the
Rockchip port.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This migrates rk_vop (the shared functions used by multiple VOP
mini-drivers) to be compatible with a live tree.
Unfortunately, there's
(i) a lot of tree traversal needed for a VOP (as each active VOP
vnode references back to the endpoints in the encoders and vice
versa) to configure the connection between VOPs and encoders;
(ii) the DTS binding is not too sane and one needs to walk a node's
parents (the original code just assumed that the device would
live 3 levels above the property linked through a phandle) until
a UCLASS_DISPLAY device can be found.
As part of the migration, the code for finding the enclosing display
device has been changed to not assume a specific depth of nesting
(i.e. we walk until we reach the root or find a matching device) and
to use the newly introduced (in the same series) ofnode_get_parent()
function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The rk_hdmi (shared functions for multiple HDMI mini-drivers) has been
using devfdt_get_addr() to read the HDMI controller's IO base address.
This will cause a failure with a live tree.
This changes the driver to use dev_read_addr() which is safe both for
flat trees and live trees.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The Rockchip video drivers need to walk the ofnode-parrents to find
an enclosing device that has a UCLASS_DISPLAY driver bound. This
adds a ofnode_get_parent()-function that returns the parent-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
U-Boot pulled in several core makefiles from Linux. The following
are not used in U-Boot:
- CONFIG_DEBUG_SECTION_MISMATCH
- CONFIG_FTRACE_MCOUNT_RECORD
- CONFIG_GCOV_KERNEL
- CONFIG_GCOV_PROFILE_ALL
- CONFIG_KASAN
- CONFIG_MODVERSIONS
We can remove the unused code if we like. (although it will get the
scripts out of sync)
CONFIG_BOOM and CONFIG_HIS_DRIVER are just mentioned in the comment
block of scripts/basic/fixdep.c
CONFIG_SHELL is not configuration, but a variable for internal-use.
It is just a historical misnomer in Kbuild.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the omap3_logic boards, the environment is always in NAND.
This removes the ENV_IS_IN_FAT flag to eliminate the extra chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
Most of architectures have .text section situated in the very beginning
of U-Boot binary and thus it is very logical that CONFIG_SYS_TEXT_BASE
is used on final linkage step to specify where U-Boot gets linked to.
For that we pass the following construction to the LD:
---------------------------->8-----------------------
xxx-ld ... -Ttext $(CONFIG_SYS_TEXT_BASE) ...
---------------------------->8-----------------------
But there could be exceptions. For example:
1. In case of ARCv2 we want to put vectors table in its own section
.ivt in front of .text section which means we need either add an
offset to CONFIG_SYS_TEXT_BASE to compensate for .ivt or don't
pass "-Ttext" to the LD at all and specify link base in linker
script directly.
2. Some architectures even though have .text section in the very
beginning of the U-Boot image still use different symbols to
specify link-base:
* NIOS2: CONFIG_SYS_MONITOR_BASE (which I really like because
that exactly what makes sense - where out image starts but not
beginning of its .text section which just happened to match the
whole image beginning)
* EXTENSA: CONFIG_SYS_TEXT_ADDR
* X86: Which doesn't use CONFIG_SYS_MONITOR_BASE in case of EFI
otherwise sets explicit link base in u-boot.lds
I think that's good to allow for flexibility and don't require each and
every architecture or even platform to specify CONFIG_SYS_TEXT_BASE as well
as use it to set .text section location.
So let's only pass "-Ttext xxx" for those architectures who don't set
link-base explicitly in their linker scripts.
This patch iaddresses comments for previously sent
https://patchwork.ozlabs.org/patch/867540/.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
These were dropped in [1], after relocation, for their values offset by
reloc_off.
Unconditionally show the HW values and add a '(reloc)' hint for the
offset values showed after relocation.
Also, the LRs' dumps are now formatted the same way the other regs' are.
[1] Commit 082693f4 ("arm64 :show_regs: show the address before relocation")
Signed-off-by: Karl Beldan <karl.beldan+oss@gmail.com>
Fix build after addition of RSA_get0_key() to LibreSSL.
Patch from Theo Buehler and Stuart Henderson.
Signed-off-by: Theo Buehler <tb@openbsd.org>
Signed-off-by: Stuart Henderson <sthen@openbsd.org>
ll_temac driver was used by Xilinx Microblaze big endian and
Xilinx ppc405/ppc440 SoCs.
ppc support was removed by: "powerpc: remove 4xx support"
(sha1: 98f705c9ce)
and Microblaze BE is not tested for a long time that's why this driver
can be removed because none is going to updated it to DM anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These got removed in config re-syncs due to a Kconfig bug. Add these
back here.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
TI_SECURE_DEVICE is used by both OMAP2+ and Keystone2 family devices,
and so when ARCH_OMAP2PLUS was used to gate off the OMAP2+ Kconfig
Keystone2 family devices lost this config option.
Move this option out of mach-omap2 Kconfig to a spot accessible by both
families. We picked arch/arm/Kconfig over the TI specific board/ti/
location as this option is not specific to our boards but rather our
architecture.
Plus at some point this option can be changed to just
SECURE_DEVICE, as having secure parts is not exclusive to TI and
so other vendors can interpret this option as needed by their device
configurations.
Fixes: a93fbf4a78 ("ARM: omap2+: rename config to ARCH_OMAP2PLUS and consolidate Kconfig")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
A number of platforms include config_distro_defaults.h but do not enable
CONFIG_DISTRO_DEFAULTS. As they plainly intended to, set that flag and
re-sync config files.
Signed-off-by: Tom Rini <trini@konsulko.com>
MMC card with EXT_CSD_REV value 9 will trigger off-by-one
bug while accessing mmc_versions array. The patch fix that.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
With modern GCC, we get warnings such as:
cmd/jffs2.c: In function 'mtdparts_init':
arch/sh/include/asm/string.h:110:38:
warning: array subscript is above array bounds [-Warray-bounds]
: "0" (__cs), "1" (__ct), "r" (__cs+__n)
~~~~^~~~
This results in a small size reduction as well.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
i.MX6 boards still using raw MMC write for SPL and
u-boot-dtb.img along with Falcon mode configurations,
so drop filesystem based write through SPL_EXT_SUPPORT.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the following devices are using a different definition for ROM
Vector Table addresses:
- i.MX6DQP = All rev
- i.MX6DQ >= rev 1.5
- i.MX6SDL >= rev 1.2
There is no need to create a new RVT macros since the only update were the
RVT base address. Remove HAB_RVT_*_NEW macros and define a new RVT base
address.
More details about RVT base address can be found on processors Reference
Manual and in the following documents:
EB803: i.MX 6Dual/6Quad Applications Processor Silicon Revision 1.2 to 1.3
Comparison
EB804: i.MX 6Solo/6DualLite Application Processor Silicon Revision 1.1
to 1.2/1.3 Comparison
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Write, Check and Set MID commands have been deprecated from the Code
Signing Tool (CST) v2.3.3 and will not be implemented in newer versions
of HAB, hence the following features are no longer available:
- Write Data
- Clear Mask
- Set Mask
- Check All Clear
- Check All Set
- Check Any Clear
- Check Any Set
- Set MID
The inappropriate use of Write Data command may lead to an incorrect
authentication boot flow. Since no specific application has been identified
that requires the use of any of these features, it is highly recommended to
add this check.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For proper authentication the HAB code must check if the CSF is valid.
Users must call the csf_is_valid() function to parse the CSF prior to
authenticating any additional images. The function will return a failure
if any of the following invalid conditions are met:
- CSF pointer is NULL
- CSF Header does not exist
- CSF does not lie within the image bounds
- CSF command length zero
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. DCD should not be present in images that will be verified
by software using HAB RVT authentication APIs. Newer versions of HAB
will generate an error if a DCD pointer is present in an image being
authenticated by calling the HAB RVT API. Older versions of HAB will
process and run DCD if it is present, and this could lead to an incorrect
authentication boot flow.
It is highly recommended this check is in place to ensure additional HAB
verified images do not include a DCD table.
Signed-off-by: Utkarsh Gupta <utkarsh.gupta@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently it is not possible to run CMD_DEK on i.MX SPL targets:
=> dek_blob 0x12000000 0x12001000 128
The system hangs after running dek_blob because the CAAM clock is being
disabled by the HAB code. There is no need to disable CAAM clock after
authenticating additional boot images, thus keep CAAM clock enabled to
address this issue.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Based on reading over the GCC manual, passing both -m2a and -m2a-nofpu
are redundant, as -m2a-nofpu will provide functional code for both. As
-m2a-nofpu functions with more toolchains and does what is expected,
switch.
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
When FASTBOOT is activated, only one the supported device is supported in
code at the same time
- CONFIG_FASTBOOT_FLASH_MMC_DEV
- CONFIG_FASTBOOT_FLASH_NAND_DEV
But Today the choice is not exclusive in Kconfig
and that cause Kconfig issue when :
- CONFIG_FASTBOOT, CONFIG_MMC, CONFIG_NAND are activated
- CONFIG_FASTBOOT_FLASH_MMC_DEV = 0
- CONFIG_FASTBOOT_FLASH_NAND_DEV is not activated
The patch add a choice in Kconfig to select the FLASH provider
- CONFIG_FASTBOOT_FLASH_MMC
- CONFIG_FASTBOOT_FLASH_NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fix two build warnings when building for arm64:
drivers/dfu/dfu_tftp.c: In function ‘dfu_tftp_write’:
drivers/dfu/dfu_tftp.c:59:37: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
ret = dfu_write_from_mem_addr(dfu, (void *)addr, len);
^
and
drivers/dfu/dfu_tftp.c: In function ‘dfu_tftp_write’:
drivers/dfu/dfu_tftp.c:41:8: warning: format ‘%u’ expects argument of type ‘unsigned int’, but argument 4 has type ‘__kernel_size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: image name: %s strlen: %u\n", __func__, sb, strlen(sb));
^
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Clean up the screaming mess of configuration options that DFU is.
It was impossible to configure DFU such that TFTP is enabled and
USB is not, this patch fixes that and assures that DFU TFTP and
DFU USB can be enabled separatelly and that the correct pieces
of code are compiled in.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
If SYS_STDIO_DEREGISTER is not selected and USB_KEYBOARD is selected
U-Boot cannot be built due to missing function stdio_deregister_dev.
So USB_KEYBOARD should select SYS_STDIO_DEREGISTER.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The SDP protocol contains multiple 32bit pointers. Add a helper function
to get a valid pointer from these values and use it.
This fixes the following warnings:
drivers/usb/gadget/f_sdp.c: In function ‘sdp_rx_data_complete’:
drivers/usb/gadget/f_sdp.c:347:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy((void *)sdp->dnl_address, req->buf + 1, datalen);
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_jump_imxheader’:
drivers/usb/gadget/f_sdp.c:625:10: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
entry = (void *)headerv2->entry;
^
drivers/usb/gadget/f_sdp.c: In function ‘sdp_handle_in_ep’:
drivers/usb/gadget/f_sdp.c:668:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
memcpy(&data[1], (void *)sdp_func->dnl_address, datalen);
^
drivers/usb/gadget/f_sdp.c:679:31: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
status = sdp_jump_imxheader((void *)sdp_func->jmp_address);
^
Signed-off-by: Andre Heider <a.heider@gmail.com>
If some configs are disabled, number of freqs array will not assigned to
correct value with bus_mode.
Synchornize the ordering with enum bus_mode in mmc.h.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
This commit fixes several issues:
- After moving env related code to ./env directory the env_common.o file
is no longer present in the system (has been replaced with built-in.o).
- Use ${OBJCOPY} if available, fallback to system default's objcopy if not
present.
- Extend the script to accept different build directory than current one.
It is extremely handy with OE usage, where source code is separated from
build.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
When booting from a non-MMC device, the MMC sub-system may not be
initialized when the environment is first accessed.
We need to make sure that the MMC sub-system is ready in even a non-MMC
boot case.
Therefore, initialize mmc before loading environment from it.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
These ARM boards are in nice shape and still being used a lot
with e.g. QEMU, so I can maintain them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The correspondence between mmc versions as used in u-boot and the version
numbers reported in register EXT_CSD_REV is wrong for versions above and
including MMC_VERSION_4_41. All those versions were shifted by one:
real 4.5 hardware appeared to be MMC_VERSION_5_0.
Fix this by adding the missing version in the correspondence table.
Reported-by: eil Eilmsteiner Heribert <eil@keba.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
After settings the speed of the sd with the switch command, a check is
done to make sure that the new speed has been set. The current check has a
masking error: speed are encoded on 4 bits only.
Fix it by masking the upper bits.
This fixes a problem seen with QEmu emulating a vexpress-a15.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The UHS modes are not supported in beagle-x15 because it's not possible to
switch the IO lines supply voltage to 1.8v.
Also HS200 cannot be supported on mmc2, because the IO lines of mmc2 are
connected to 3.3v.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the new compatible string "ti,dra7-hsmmc" that was specifically
added for dra7 and dra72. This is required since for dra7 and dra72
processors iodelay values has to be set unlike other processors.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc core has defined a new parameter *clk_disable* to gate the clock.
Disable the clock here if *clk_disable* is set.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
When the clock is applied, compute the actual value of the clock. It may be
slightly different from the requested value (max freq, divisor threshold)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The default configuration is usually working fine for the the HS modes.
Don't enforce the presence of a dedicated pinmux for the HS modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met.
Add support to parse mux values and iodelay values from device tree
and set these depending on the enumerated MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new API to perform iodelay recalibration without isolate
io to be used in uboot.
The data manual of J6/J6 Eco recommends to set different IODELAY values
depending on the mode in which the MMC/SD is enumerated in order to
ensure IO timings are met. The MMC driver can use the new API to
set the IO delay values depending on the MMC mode.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the mmc_of_parse library function to populate mmc_config instead of
repeating the same code in host controller driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
>From OMAP3 SoCs (OMAP3, OMAP4, OMAP5, AM572x, AM571x), the DAT/CMD lines
reset procedure section in TRM suggests to first poll the SRD/SRC bit
until it is set to 0x1. But looks like that bit is never set to 1 and there
is an observable delay of 1sec everytime the driver tries to reset DAT/CMD.
(The same is observed in linux kernel).
Reduce the time the driver waits for the controller to set the SRC/SRD bits
to 1 so that there is no observable delay.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.
The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.
The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
No functional change. Move bus width configuration setting to a
separate function and invoke it only if there is a change in the
bus width.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Fixes a bug found on thuban boards, which were for 2 years in
a long-term test with varying temperatures. They showed
problems in u-boot when attaching the ubi partition:
U-Boot# run flash_self_test
Booting from nand
set A...
UBI: attaching mtd1 to ubi0
UBI: scanning is finished
data abort
pc : [<87f97c3c>] lr : [<87f97c28>]
reloc pc : [<8012cc3c>] lr : [<8012cc28>]
sp : 85f686e8 ip : 00000020 fp : 000001f7
r10: 8605ce40 r9 : 85f68ef8 r8 : 0001f000
r7 : 00000001 r6 : 00000006 r5 : 0001f000 r4 : 85f6ecc0
r3 : 00000000 r2 : 44e35000 r1 : 87fcbcd4 r0 : 87fc755b
Flags: nZCv IRQs off FIQs on Mode SVC_32
Resetting CPU ...
Reason is, that accidentially the U-Boot implementation
from __schedule_ubi_work() did not check the flag
ubi->thread_enabled and started with wearleveling work,
but ubi did not have setup all structures at this point
and crashes.
Solve this problem by splitting work scheduling and processing.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Heiko Schocher <hs@denx.de>
Previous patch for this driver breaks i2c initialization.
commit 8bcf12ccce ("i2c: mvtwsi.c: Avoid NULL dereference")
If actual_speed is passed as NULL in this function:
static void __twsi_i2c_init(struct mvtwsi_registers *twsi, int speed,
int slaveadd, uint *actual_speed)
than __twsi_i2c_set_bus_speed never get called. This causes i2c clock
to run on default speed - 2MHz (measured with oscilloscope). This is issue
on some boards, sunxi for example, since on I2C0 bus PMU is connected.
The bootlogs with and without the patch are as follows:
Wihtout the patch:
U-Boot SPL 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200)
DRAM: 1024 MiB
Failed to set core voltage! Can't set CPU frequency
Trying to boot from FEL
U-Boot 2018.03-rc2 (Feb 13 2018 - 09:23:17 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
With the patch:
U-Boot SPL 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2
Trying to boot from FEL
U-Boot 2018.03-rc2-00001-g838ff85 (Feb 13 2018 - 09:24:34 +0200) Allwinner Technology
CPU: Allwinner A20 (SUN7I)
Model: Olimex A20-OLinuXino-LIME2
I2C: ready
DRAM: 1 GiB
MMC: SUNXI SD/MMC: 0
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dtc produces these warnings when compiling sandbox:
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Could not get phandle node for /base-gpios:num-gpios(cell 0)
arch/sandbox/dts/test.dtb: Warning (gpios_property):
Missing property '#gpio-cells' in node /reset-ctl or bad phandle
(referred from /extra-gpios:num-gpios[0])
Both are due to it assuming that the 'num-gpios' property holds a phandle
pointing to a GPIO node.
To avoid these warnings, rename the sandbox property so that it does not
include the string 'gpios'.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dtc produces these warnings when compiling sandbox:
arch/sandbox/dts/test.dtb: Warning (reg_format): "reg" property in /chosen/chosen-test has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #address-cells value for /chosen/chosen-test
arch/sandbox/dts/test.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /chosen/chosen-test
Add the missing properties to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: f200680 (dm: core: parse chosen node)
Memory banks with address 0 and size 0 are empty and should not be
passed to the OS via device tree.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Only ARM and in some configs MIPS really implement arch_fixup_fdt().
Others just use the same boilerplate which is not good by itself,
but what's worse if we try to build with disabled CONFIG_CMD_BOOTM
and enabled CONFIG_OF_LIBFDT we'll hit an unknown symbol which was
apparently implemented in arch/xxx/lib/bootm.c.
Now with weak arch_fixup_fdt() right in image-fdt.c where it is
used we get both items highlighted above fixed.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With fastboot support enabled, it is useful to be able to list
the eMMC EFI partitions, so select the CONFIG_EFI_PARTITION option.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Drop the whole map/unmap_physmem stuff and just use the address
already obtained from DT in ofdata_to_platdata(), instead of
repeating that, wrongly, in probe.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Get rid of the SH I2C driver on Porter and enable the IIC driver
instead . The old SH I2C is completely broken on Porter anyway
and the DM/DT capable IIC driver allows access to the PMIC too.
Use the DM/DT capable driver instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable cache and time commands, which are convenience tools for
doing benchmarks and various boot tests. Also enable FIT support
for booting fitImage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Fix ommission where the u-boot,dm-pre-reloc DT bit was pulled into the
common DT, not the U-Boot specific DT part. Move it to U-Boot DT part.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With multiple environments, the 'get_char' callback for env
drivers does not really make sense any more because it is
only supported by two drivers (eeprom and nvram).
To restore single character loading for these drivers,
override 'env_get_char_spec'.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Commit 7d714a24d7 ("env: Support multiple environments") added
static variable env_load_location. When saving environmental
variables, this variable is presumed to have the value set before.
In case the value was set before relocation and U-Boot runs from a
NOR flash, this variable wasn't writable. This causes failure when
saving the environment. To save this location, global data must be
used instead.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Maxime Ripard <maxime.ripard@free-electrons.com>
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Those two nodes are needed to configure pinmux before relocation
and to configure clock before relocation, since CPG/MSSR needs
access to RST node. This is not noticable on Gen3, but on Gen2
this causes problems in SPL if they are not available early.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable support for applying DT overlays on Gen3. This is convenient
for handling extra additional hardware, like ie. the Kingfisher.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The SD driver calls clk_set_rate() before clk_enable(), yet clk_set_rate()
implementation in the clock driver does not set the SD-IF divider. Fix it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Commit 958d55f26c ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
Kconfig should only 'select' features that are required for an arch.
Standard features that can be disabled without breaking board support
should use 'imply' instead, to allow users to disable it.
These options are changed for mach-socfpga:
- DM_SPI & DM_SPI_FLASH: only required with QSPI support enabled
- SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION: the boot rom supports a
partitionless mode also, where SPL is located at address 0
- HW_WATCHDOG: while all mainline board defconfigs use it, U-Boot
should still work without it.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
All Socfpga boards from ./include/configs/socfpga_* define
CONFIG_HW_WATCHDOG.
To ease CONFIG_HW_WATCHDOG conversion to Kconfig select it in
config ARCH_SOCFPGA (arch/arm/Kconfig) section.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This patch adds "spi-flash" to the compatible list of the qspi flash
chip for all socfpga boards. This is required to make qspi work on
these boards on top of the recent fixes. Without the "spi-flash"
compatible string for the flash chip, the speed cannot be read and a
speed of 0Hz is used (which results in a divide-by-zero on these
boards).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
ARC Elf32 tools by default enable usage of so-called "small data"
section or in ARC PRM parlance "GP-relative addressing".
The idea is to put up to 2kB of frequently used data into a separate
location and use indirect addressing via dedicated core register (GP).
Where GP is used as a base for offset calculation.
And so if "-msdata" toggle is passed to the compiler either explicitly
or implicitly (that's Elf32 tools case) it will try to put some data
in that "small data" area and then to calculate real offset from GP
to be encoded in instructions we need to know the base value which
liker gets from __SDATA_BEGIN__ symbol in hte linker script.
In U-Boot we don't use that feature and linker script doesn't define
__SDATA_BEGIN__ which gives us the following linkage error if we use
Elf32 tools:
------------------------->8-------------------
LD u-boot
.../bin/arc-elf32-ld.bfd: Error: Linker symbol __SDATA_BEGIN__ not found
.../bin/arc-elf32-ld.bfd: final link failed: Bad value
------------------------->8-------------------
Note if uClibc or glibc tools are used that problem doesn't happen
because usage of "small data section" is disabled by default as not very
useful for bigger executables. Moreover GP is just another name of r26
so we're loosing 1 core register which is not used by the compiler as a
generic register with "-msdata".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_BOOTCOUNT_SINGLEWORD
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Ian Ray <ian.ray@ge.com>
With commit 9bd76b8076 ("spl: make CONFIG_OF_EMBED pass dts through
fdtgrep"), CONFIG_SPL_MULTI_DTB_FIT has been broken because
cmd_fdtgrep was now unknown in scripts/Makefile.spl after moving
it to dts/Makefile. This bug has been introduced with v2018.01.
This patch moves cmd_fdtgrep from dts/Makefile to scripts/Makefile.lib
and includes scripts/Makefile.lib in scripts/Makefile.spl.
Fixes: 9bd76b8076 ("spl: make CONFIG_OF_EMBED pass dts through fdtgrep")
Reported-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
ATF recently began announcing PSCI v1.1. Since that version is unknown
to u-boot, the PSCI device nodes were not updated.
Switch from the case statement to a greater/less-than comparison so that
v1.1, as well as future versions, get at least the compatible nodes of
known versions.
PSCI v1.1 doesn't seem to have introduced a new corresponding compatible.
Signed-off-by: Andre Heider <a.heider@gmail.com>
The single argument `--noheader' is expecting isn't taken from getopt
parsing, but instead from the remaining argv arguments.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
>From DFU_ALT_INFO_EMMC (include/environment/ti/dfu.h) we can see that
rootfs will be flashed to second partition on eMMC. But at the moment we
have only one partition in $partitions environment variable. Let's add
"bootloader" partition prior to "rootfs", so that DFU works correctly.
This also fixes eMMC boot, which looks for rootfs on second partition.
"bootloader" partition start corresponds to "u-boot.img.raw" in DFU
eMMC info, which is 0x300 sector (384 KiB offset from eMMC start).
rootfs start address can be also found from DFU eMMC info.
bootloader-related area is finished at 0x1500 sector (2688 KiB offset
from eMMC start). This should be the start address for rootfs in
$partitions environment variable.
While at it, fix U-Boot environment address to be the same as for
AM57x EVM, so that it doesn't clash with other partitions.
So now eMMC layout looks like this:
===============================================================
0 +------------------------+
| MBR/GPT header | 128 -
128 +------------------------+
| MLO | 256 -
384 +------------------------+
| u-boot.img | 1792 bootloader
2176 +------------------------+
| //////// hole //////// | 256 -
2432 +------------------------+
| U-Boot environment | 128 -
2560 +------------------------+
| U-Boot environment | 128 -
| (redundant) |
2688 +------------------------+
| rootfs | remaining rootfs
end +------------------------+
===============================================================
"hole" area can be used further for storing U-Boot environment (like
it's done in AM57x EVM config file) or for increasing u-boot.img area
(in case u-boot.img size increased, e.g. if new dtbs were added).
This commit conforms with Linux partition table from f6d245b8c5
("arm: am57xx: Fix Linux boot from eMMC") commit, making things in
uniform way.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.
Signed-off-by: Tom Rini <trini@konsulko.com>
ISO and EFI partition configs in SPL are selected by default.
However, they are not being used.
Therefore, remove ISO and EFI partition support in SPL.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When this config is enabled, <asm/arch/boot0.h> is included,
but the Kconfig help says this should be a define
(ARM_SOC_BOOT0_HOOK).
The code for this in arch/arm/lib/vectors.s was changed on
01/02/2017 with commit ce62e57fc5 ("ARM: boot0 hook: remove macro,
include whole header file").
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Commit 6808ef9ac2 ("move booti_setup to arch/arm/lig/image.c")
not only moved the code, but also replaced a tab with 4 spaces
to break the Linux coding style.
Restore tab indentation.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Chen <bin.chen@linaro.org>
With commit 6808ef9ac2 ("move booti_setup to arch/arm/lig/image.c"),
images->ep has not been set at this point.
Fixes: 6808ef9ac2 ("move booti_setup to arch/arm/lig/image.c")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Chen <bin.chen@linaro.org>
This allows running tests on emulated KC705 board with DC233C xtensa
core. It expects to find conf.xtfpga_qemu in the uboot-test-hooks.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Remove CONFIG_BOOT_RETRY_TIME as it doesn't do much good and enable
CONFIG_HUSH_PARSER in xtfpga_defconfig.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
xtensa toolchains are core-specific, so give full toolchain name and
download corresponding prebuilt toolchain from the github release.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Fix build warning in arch/microblaze/lib/bootm.c with gcc 7.3.0:
warning: this 'if' clause does not guard... [-Wmisleading-indentation]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Fix build warning in arch/arm/mach-omap2/emif-common.c and
arch/arm/mach-omap2/omap4/emif.c with gcc 7.3.0:
warning: duplicate 'const' declaration specifier [-Wduplicate-decl-specifier]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix build warning in drivers/video/ivybridge_igd.c with gcc 7.3.0:
warning: 'ivb_pm_gt2' defined but not used [-Wunused-const-variable=]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The fdt_record_loadable()-function was wedged between other functions
that were guarded by ARCH_FIXUP_FDT_MEMORY. This could lead to linker
errors on some configurations.
With this change, fdt_record_loadable() is moved out of the
ARCH_FIXUP_FDT_MEMORY guard (plus I tried to retain alphabetical
ordering for functions by placing it appropriately).
References: 9f45aeb ("spl: fit: implement fdt_record_loadable")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reported-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
When saving the environment on a platform which has DMA alignment
larger than the natural alignment, env_fat_save triggers a debug
message in file_fat_write:
Saving Environment to FAT... writing uboot.env
FAT: Misaligned buffer address (9df1c8e0)
OK
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.
I did not attempt to add more default values in and for now will leave
that to maintainers.
Signed-off-by: Tom Rini <trini@konsulko.com>
Patch queue for efi in 2018.03 - 2018-02-10
This time we have a few important bug fixes. Most noticable are:
- Fix OpenBSD loader with CONFIG_BLK=n
- Fix builds on various circumstances
- Add missing stubs so callers don't call NULL
- Bump UEFI revision to 2.7
efi_disk_register should return as status code (efi_status_t).
Disks with zero blocks should be reported as 'not ready' without throwing
an error.
This patch solves a problem running OpenBSD on system configured with
CONFIG_BLK=n (e.g. i.MX6).
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add stubs for UpdateCapsule, QueryCapsuleCapabilities, and
QueryVariableInfo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
README.efi describes two different concepts:
* U-Boot exposing the UEFI API
* U-Boot running on top of UEFI.
This patch splits the document in two.
Religious references are removed.
The separation of the concepts makes sense before detailing the internals
of U-Boot exposing the UEFI API in a future patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Change the return type of efi_driver_init() to efi_status_t.
efi_driver_init() calls efi_add_driver() which returns an efi_status_t
value. efi_driver_init() should not subject this value to a conversion to
int losing high bits on 64bit systems.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently the UEFI revision number in the system table header is set to
2.0.5. This version number does not refer to any existing version of the
UEFI standard.
Set the revision number to 2.7.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we set the function pointer for the CreateEventEx boot service
to NULL. When called this would lead to an immediate failure.
A function stub is provided which handles the case that the boot service
is called without an event group and returns EFI_UNSUPPORTED otherwise.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
For EFI binaries we need special CFLAGS.
They were specified for an object file that since has been replaced.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The bootefi command is missing in the online help for
bootefi bootmgr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Before the patch an undefined constant EFI_SUBSYSTEM was used in the
crt0 code. The current version of binutils does not swallow the error.
https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=888403
The necessary constant IMAGE_SUBSYSTEM_EFI_APPLICATION is already
defined in pe.h. So let's factor out asm-generic/pe.h for the
image subsystem constants and use it in our assembler code.
IMAGE_SUBSYSTEM_SAL_RUNTIME_DRIVER does not exist in the specification
let's use IMAGE_SUBSYSTEM_EFI_ROM instead.
The include pe.h is only used in code maintained by Alex so let him be the
maintainer here too.
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
config_phylib_all_drivers.h should be included when CONFIG_PHYLIB and
CONFIG_TSEC_ENET are defined.
Fixes: 3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Extend the instantiate_rng() function and the corresponding CAAM job
descriptor to instantiate all RNG state handles. This moves the RNG
instantiation code in line with the CAAM kernel driver.
Previously, only the first state handle was instantiated. The second
one was instantiated by the CAAM kernel driver. This works if the
kernel runs in secure mode, but fails in non-secure mode since the
kernel driver uses DEC0 directly instead of over the job ring
interface. Instantiating all RNG state handles in u-boot removes the
need for using DEC0 in the kernel driver, making it possible to use
the CAAM in non-secure mode.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: York Sun <york.sun@nxp.com>
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Enable fall back option to
qspi boot in case of secure boot.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove dependency of SYS_HAS_SERDES for Layerscape Chasis 2 and
Layerscape Chasis 3.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently in LS1088A, XIP mode in QSPI works up to 16 MB
addresses. This patch enables QSPI support in XIP mode for
addresses above 16 MB as well.
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
config_fallbacks.h has some logic that sets HAVE_BLOCK_DEVICE
based on a list of enabled options. Moving HAVE_BLOCK_DEVICE to
Kconfig allows us to drastically shrink the logic in
config_fallbacks.h
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rename HAVE_BLOCK_DEVICE to CONFIG_BLOCK_DEVICE]
Signed-off-by: Tom Rini <trini@konsulko.com>
Migrate the base and sub-options to Kconfig. Note that we only enable
this in the base sandbox config now.
Cc: Alexey Brodkin <alexey.brodkin@gmail.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Is this driver still used anywhere? It's fishy that it's only enabled
in sandbox anymore.
config_fallback.h has some logic that checks a variety of options
and selects LIB_UUID if it hasn't already been selected. This
will all LIB_UUID in Kconfig and select this option for the list
of options to allow us to remove the logic from fallbacks
Signed-off-by: Adam Ford <aford173@gmail.com>
config_fallbacks.h had some logic to automatically select
LIB_RAND if RANDOM_UUID or CMD_UUID were set if LIB_HW_RAND wasn't
already selected. By migrating LIB_HW_RAND to Kconfig, we can
remove this check from config_fallbacks.h and put it into Kconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
[trini: Turn into a choice, add NET_RANDOM_ETHADDR]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_APBH_DMA
CONFIG_APBH_DMA_BURST
CONFIG_APBH_DMA_BURST8
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
[trini: Add in MMC as well]
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no reason to unconditially select network commands as distro
defaults without networking enable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Distro default configuration contains also dhcp and pxe setting which
can't working without enabling CONFIG_NET.
EFI is not required that's why it is not enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable CONFIG_ENV_VARS_UBOOT_CONFIG for all STM32 boards
It allows to retrieve the SoC name into the "soc" environment
variable.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Simplify SPL_LDSCRIPT config by using the new arch Kconfig
configurations ARCH_MX23 and ARCH_MX28.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
The motivation for moving MX23 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Since CONFIG_MXC_UART is already in Kconfig, move this from
the header to imx6q_logic_defconfig
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This commit cleans up the README.watchdog by removing the reminescent of
ADI's Blackfin architecture removed some time ago.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit removes an attempt to workaround a previous compilation
warning that is is now fixed in "include/configs/ti_omap3_common.h".
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This commit fixes the following compiler warnings when DM_SERIAL is
enabled.
---8<-------------------------------------------------------------------
...
CC spl/board/ti/evm/evm.o
In file included from /solution/scm/u-boot-master/board/ti/evm/evm.c:16:0:
/solution/scm/u-boot-master/include/ns16550.h:31:0: warning: "CONFIG_SYS_NS16550_REG_SIZE" redefined
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
In file included from /solution/scm/u-boot-master/include/configs/omap3_evm.h:22:0,
from include/config.h:5,
from /solution/scm/u-boot-master/include/common.h:21,
from /solution/scm/u-boot-master/board/ti/evm/evm.c:14:
/solution/scm/u-boot-master/include/configs/ti_omap3_common.h:33:0: note: this is the location of the previous definition
# define CONFIG_SYS_NS16550_REG_SIZE (-4)
LD spl/board/ti/evm/built-in.o
...
CC spl/drivers/serial/ns16550.o
In file included from /solution/scm/u-boot-master/drivers/serial/ns16550.c:11:0:
/solution/scm/u-boot-master/include/ns16550.h:31:0: warning: "CONFIG_SYS_NS16550_REG_SIZE" redefined
#define CONFIG_SYS_NS16550_REG_SIZE (-1)
In file included from /solution/scm/u-boot-master/include/configs/omap3_evm.h:22:0,
from include/config.h:5,
from /solution/scm/u-boot-master/include/common.h:21,
from /solution/scm/u-boot-master/drivers/serial/ns16550.c:7:
/solution/scm/u-boot-master/include/configs/ti_omap3_common.h:33:0: note: this is the location of the previous definition
# define CONFIG_SYS_NS16550_REG_SIZE (-4)
LD spl/drivers/serial/built-in.o
...
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit ff98cb9051 ("part: extract MBR signature from partitions")
blindly switched allocated by ALLOC_CACHE_ALIGN_BUFFER buffer type from
"unsigned char" to "legacy_mbr" which caused allocation of size =
(typeof(legacy_mbr) * dev_desc->blksize) instead of just space enough
for "legacy_mbr" structure.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Tom Rini <trini@konsulko.com>
Follow bootz's pattern by moving the booti_setup to arch/arm/lib.
This allows to use booti_setup in other paths, e.g booting
an Android image containing Image format.
Note that kernel relocation is move out of booti_setup and it is the
caller's responsibility to do it and allows them do it differently. say,
cmd/booti.c just do a manually, while in the bootm path, we can use
bootm_load_os(with some changes).
Signed-off-by: Bin Chen <bin.chen@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The second area of android image was intended to put a 2nd stage
bootloader but in practice were rarely used (in my knowledge).
An proposal was made to the AOSP to (re)use the second area as the dtb[1],
This patch itself doesn't depend on that proposal being accepted but it won't
be that helpful as well if that proposal won't be accepted. But don't do
any harm as well.
[1] https://android-review.googlesource.com/#/c/417447/
Signed-off-by: Bin Chen <bin.chen@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
On detach UBI attempts to update fastmap after closing user interfaces
but at this point UBI volumes have already been free()'ed and fastmap
can no longer access these data structures.
Signed-off-by: Martin Townsend <mtownsend1973@gmail.com>
Cc: hs@denx.de
Cc: kmpark@infradead.org
Cc: richard@sigma-star.at
For '#ifndef CONFIG_DM_I2C' twsi_i2c_init() passes NULL as
4th parameter to __twsi_i2c_init().
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Make the ihs_i2c driver DM-compatible; for legacy boards, the old functions are
retained within #ifdefs.
No board uses the new DM driver yet; this patch only lays the foundation for
future support.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Prepare the function interface of the ihs_i2c driver for DM conversion
in a future patch.
While we're at it, fix some style violations, and make the code more readable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Some functions in the fsl_i2c driver are declared as inline, even though
they are quite large, which needlessly increases the size of the
resulting binary.
This patch removes the inline declarations.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Fix some style violations in the fsl_i2c I2C driver, and use shorter
type names for variables in some cases.
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
'default' on a choice refers to the symbol selected by default, not to
the choice mode, so 'default n' is meaningless.
No functional changes. Optional choices implicitly default to n mode
(and there is no way to make them default to another mode).
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection n (undefined) of <choice> (defined at drivers/usb/ulpi/Kconfig:3) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
There is no EMMC symbol in the "enable different boot versions for the
shc board" choice. SHC_EMMC was probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection EMMC (undefined) of <choice> (defined at board/bosch/shc/Kconfig:15) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
FreeBSD, like OpenBSD, uses BIG_ENDIAN, LITTLE_ENDIAN, and BYTE_ORDER,
whereas Linux and compatibles use __-prefixed names. Define the names
the same as the OpenBSD block below it.
cmd/Makefile has:
ifdef CONFIG_FPGA
obj-$(CONFIG_CMD_FPGA) += fpga.o
endif
which means that if CONFIG_FPGA is not set, CONFIG_CMD_FPGA silently
does nothing. Let's remove that Makefile conditional and instead express
this equivalent dependency in Kconfig, so a lot of redundant
# CONFIG_CMD_FPGA is not set
can be removed from board defconfigs that don't actually have an FPGA.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
These are declared in Kconfig, but some #defines have crept in.
CONFIG_FPGA
CONFIG_FPGA_ALTERA
CONFIG_FPGA_CYCLON2
CONFIG_FPGA_SOCFPGA
CONFIG_FPGA_XILINX
CONFIG_FPGA_ZYNQMPPL
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
In most places in the code we cast this to an unsigned long, but in one
place we cast to an unsigned int. For consistency and to fix a warning
on 64bit targets, always cast this to unsigned long. For the long term
we should however change the declaration of dma_buf.
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The build script should not manipulate shell flags (especially '-e').
A non-zero exit value can also be catched with 'cmd || ret=$?'.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a new option '-E' for treating all compiler warnings as errors.
Eventually this will pass 'KCFLAGS=-Werror' to Kbuild.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Probably not all users are aware of this possibility, thus add a
pointer to the README. Also add a useful example.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds a sec_init call into arch_misc_init(). Doing so in
conjunction with the patch "drivers/crypto/fsl: assign job-rings to
non-TrustZone" enables use of the CAAM in Linux when OPTEE/TrustZone is
active.
u-boot will initialise the RNG and assign ownership of the job-ring
registers to a non-TrustZone context. With recent changes by Lukas Auer to
fully initialize the RNG in sec_init() this means that u-boot will hand-off
the CAAM in a state that Linux then can use the CAAM without touching the
reserved DECO registers.
This change is safe both for the OPTEE/TrustZone boot path and the regular
non-OPTEE/TrustZone boot path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marco Franchi <marco.franchi@nxp.com>
Cc: Vanessa Maegima <vanessa.maegima@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
After enabling TrustZone various parts of the CAAM silicon become
inaccessible to non TrustZone contexts. The job-ring registers are designed
to allow non TrustZone contexts like Linux to still submit jobs to CAAM
even after TrustZone has been enabled.
The default job-ring permissions after the BootROM look like this for
job-ring zero.
ms=0x00008001 ls=0x00008001
The MS field is JRaMIDR_MS (job ring MID most significant).
Referring to "Security Reference Manual for i.MX 7Dual and 7Solo
Applications Processors, Rev. 0, 03/2017" section 8.10.4 we see that
JROWN_NS controls whether or not a job-ring is accessible from non
TrustZone.
Bit 15 (TrustZone) is the logical inverse of bit 3 hence the above value of
0x8001 shows that JROWN_NS=0 and TrustZone=1.
Clearly then as soon as TrustZone becomes active the job-ring registers are
no longer accessible from Linux, which is not what we want.
This patch explicitly sets all job-ring registers to JROWN_NS=1 (non
TrustZone) by default and to the Non-Secure MID 001. Both settings are
required to successfully assign a job-ring to non-secure mode. If a piece
of TrustZone firmware requires ownership of job-ring registers it can unset
the JROWN_NS bit itself.
This patch in conjunction with a modification of the Linux kernel to skip
HWRNG initialisation makes CAAM usable to Linux with TrustZone enabled.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Alex Porosanu <alexandru.porosanu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Aneesh Bansal <aneesh.bansal@nxp.com>
Link: https://github.com/OP-TEE/optee_os/issues/1408
Link: https://tinyurl.com/yam5gv9a
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
We should take the MX6DP and MX6QP options in consideration
when defining imx_iomux_v3_setup_pad().
Based on a patch by Pierluigi Passaro <pierluigi.p@variscite.com>
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The original text is from the time that the config options were not
converted to Kconfig.
After the conversion to Kconfig only CONFIG_SECURE_BOOT and
CONFIG_CMD_DEKBLOB need to be selected by the user.
The other config options are automatically selected by the Kconfig
logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
The input keycode KEY_POWER is used in the imx6ull.dtsi file,
hence include the input header where used.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the mx6sabresd:
=> fastboot 0
On the Linux PC connected via USB:
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.01-00550-g7517cfe
finished. total time: 0.000s
$ sudo fastboot reboot -i 0x0525
(this causes the mx6sabresd to reboot)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Selecting CONFIG_USB_FUNCTION_MASS_STORAGE=y in the defconfig leads to
the following error:
cmd/built-in.o: In function `do_usb_mass_storage':
cmd/usb_mass_storage.c:217: undefined reference to `fsg_main_thread'
cmd/usb_mass_storage.c:170: undefined reference to `fsg_init'
CONFIG_USB_FUNCTION_MASS_STORAGE option is built only for
the non-SPL case as per the logic in drivers/usb/gadget/Makefile,
so remove the incorrect CONFIG_SPL ifdefery to fix the build
failure.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
SION bit should be used in the situation that we need
to read back the value of a pin and should not be set by
default macro.
We get some malfunction as raised by following thread
https://www.spinics.net/lists/linux-usb/msg162574.html
As reported by this application note:
https://www.nxp.com/docs/en/application-note/AN5078.pdf
The software input on (SION) bit is an option to force an input
path to be active regardless of the value driven by the
corresponding module. It is used when the nature direction
of a pin depending on selected alternative function is an output,
but it is needed to read the real logic value on a pin.
The SION bit can be used in:
• Loopback: the module of a selected alternative function drives
the pad and also receives the pad value as an input
• GPIO capture: the module of a selected alternative function
drives the pin and the value is captured by the GPIO
SION bit is not necessary when the pin is configured as a peripheral
apart specific silicon bug. If an application needs to have this
set, this should be done in board file or in dts file
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Introduce SDR104 and HS200 support
The implementation takes linux kernel sdhci.c and sdhci-esdhc-imx.c
as reference.
- Implement esdhc_change_pinstate to dynamically change pad settings
- Implement esdhc_set_timing
- Implement esdhc_set_voltage to switch voltage
- Implement fsl_esdhc_execute_tuning to execute time process
- Enlarge the cfg->f_max to 200MHz.
- Parse fsl,tuning-step, fsl,tuning-start-tap and
fsl,strobe-dll-delay-target from device tree.
- Parse no-1-8-v property
- Introduce esdhc_soc_data to indicate the flags and caps
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The board header file included a reference to the starting point
from nitrogen6x.h, but since so much changed, the file bears
little resemblance to that file.
Signed-off-by: Eric Nelson <eric@nelint.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This patch just changes the order of configuration items in
mx6memcal_defconfig to match the Kconfig layout, making it easier
to track changes made using menuconfig.
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
The exact definition of a successful boot is defined by user-space.
Determine the boot partition automatically. A partition is selected if
file `/boot/bootcause/firstboot' exists (meaning that the partition has
freshly installed software) OR if file `/boot/fitImage' exists.
When userspace determines that new software was successfully installed,
it must (1) delete `/boot/fitImage' on the _inactive_ partition and (2)
remove `/boot/bootcause/firstboot'.
Enable video, but do not display logos or other version information.
Silence kernel console logging by default.
Print a message to VGA screen in case of boot failure and reset bootcount
to allow the user to attempt boot again.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.
Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.
The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.
Note that the PCIe controller is _not_ put back into a safe state prior
to board reset. This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There are two I210s on the b850v3 and one on the b450v3 and b650v3.
One is connected to Marvell 88e6240 which is already programmed.
Follow the flow documented in doc/README.enetaddr: set the
enet[0-9]*addr environment variable and let the driver program the
hardware.
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order.
The environment variables are removed after programming the hardware
because the variables seem to influence MAC addresses also after U-Boot.
Specifically the MAC address of FEC (MC interface) would be incorrectly
set: 'ethaddr', which maps to the first I210 chip and is set to I210's
default address read from the driver by eth_write_hwaddr in eth_legacy.c
because the variable is undefined (not set even by bx50v3.c), would
result in the eth0 interface's MAC address to be set to I210's default
address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Instead of programming the hardware directly in the board
implementation, follow the flow documented in doc/README.enetaddr: set
the enet[0-9]*addr environment variable and let the driver program the
hardware.
This avoids duplicating the implementation as it already exists in the
driver (drivers/net/fec_mxc.c: fec_set_hwaddr).
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order, i.e. FEC always has the index 2.
The FEC driver does *not* set the flag Set MAC Address on Transmit (bit
set_eth0_mac_address used to do but this is unnecessary as the Linux
networking stack fills in the MAC address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The change in i2c configuration added to support access to the VPD has
inadvertantly caused access to i2c buses 1 & 2 to be lost. This has
resulted in the configuration for the PMIC to be attempted on the wrong
bus and thus isn't taking effect.
Add the required configuration to return access to buses 1 & 2. In order
to ensure that any users of the bus numbering prior to addition in VPD
patches work, add buses before configuration related to mux on bus 0 and
tweak VPD bus usage to fit new numbering scheme.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Implement programming MAC address to the hardware, i.e. external flash
seen as EEPROM.
MAC address is only written if it differs from what is already stored in
flash or if reading the current MAC address fails.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Split the implementation of e1000_read_mac_addr into eeprom and register
versions called by e1000_read_mac_addr.
This allows for calling e1000_read_mac_addr when MAC address is needed
with no constraints where it is read from, and for calling the register
and, especially, the eeprom version directly in order to specify where
to read the address from.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
CC: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
When building for 64bits system, we get some warnings about type
cast between pointer and integer. This patch eliminates the warnings
by using ulong/long type which is 32bits on 32bits system or 64bits on
64bits system.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The MIB RAM and FIFO receive start register does not exist on
i.MX8M. Accessing these register will cause system hang.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Include i.MX8M in lcdif register layout map.
Also included i.MX7ULP in this patch, since share same with i.MX8M.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
i.MX8M OCOTP follow same flow as i.MX6Q, but it has 64 banks
and each bank 4 words.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add i.MX8M support. Because i.MX8M use SiP call trap
to Arm Trusted Firmware to handle M4, so use #ifdef
to avoid build error on i.MX6/7.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move i.MX6/7 bootaux code to imx_bootaux.c.
The i.MX6/7 has different src layout, so define M4 reg offset
to ease the cleanup. Redefine the M4 related BIT for share
common code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Move imx_get_mac_from_fuse to a new mac.c for i.MX6/7.
Since fuse regs structure are different for i.MX6/7, use mac
address offset in code and define a new local struture
imx_mac_fuse.
Also sort the config order.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add clock driver to support i.MX8M.
There are two kind PLLs, FRAC pll and SSCG pll. ROM already
configured SYS PLL1/2, we only need to configure the output.
ocotp/i2c/pll decoding and configuration/usdhc/lcdif/dram pll/
enet clock are configured in the code.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable nand on mmc defconfig, so-that preparing nand
for writing/updating bootimage, Linux becomes easy.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
nand device needed for mmc config to access nand
for write and update so enabling SPL_SUPPORT to mmc
or nand is wrt to env device rather nand driver check.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add i.MX7 PSCI system power off support, linux
kernel can use "poweroff" command to power off
system via SNVS, PMIC power will be disabled.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Add i.MX7 PSCI system reset support, linux
kernel can use "reboot" command to reset
system even wdog driver is disabled in kernel.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Use PSCI 1.0 instead of 0.1 to support more power
management feature like system reset, power off etc..
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The EFI implementation does not fit into any of the existing categories.
Provide LOGC_EFI so that EFI related message can be filtered.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When functions return an error it propagates up the stack to the point
where it is reported. Often the error code provides enough information
about the root cause of the error that this is obvious what went wrong.
However in some cases the error may be hard to trace. For example if a
driver uses several devices to perform an operation, it may not be
obvious which one failed.
Add a log_ret() macro to help with this. This can be used to wrap any
error-return value. The logging system will then output a log record when
the original error is generated, making it easy to trace the call stack
of the error.
This macro can significantly impact code size, so its use is controlled
by a Kconfig option, which is enabled for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test of the 'log format' and 'log rec' commands. This also covers
things like log_get_cat_by_name(), since they are used by these commands.
Fix a style nit in the tests also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'log rec' command which allows a log record to be manually output.
This is useful for scripts which want full control over what is logged. It
also permits easy testing of the log system.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a 'log format' command which can display or change the log output
format. This is useful for changing how much information is displayed. The
ordering of the fields is fixed.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is useful to be able to control the output format of log records on the
console. As a starting point, add definitions for controlling which
elements of the log record are displayed. Use function and message as the
default, since these are the most useful fields.
Signed-off-by: Simon Glass <sjg@chromium.org>
Category and level both use an enum for their ID values. Add functions to
convert these IDs to strings and vice versa. This will allow the log to
output the strings instead of the (inscrutable) values.
At the same time, add a new 'driver-model' category, to cover core
driver-model functions and fix an incorrect value for LOGL_MAX.
Tests will be added with the new 'log' subcommands.
Signed-off-by: Simon Glass <sjg@chromium.org>
(Updated to correct clang warnings)
Each uclass has a driver name which we can use to look up the uclass. This
is useful for logging, where the uclass ID is used as the category.
Add a function to handle this, as well as a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
After moving some USB gadget configs (USB_FUNCTIONS_*) to Kconfig it
turned out that following *_defconfig entries for RockChip are not
needed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The CONFIG_USB_FUNCTION_MASS_STORAGE must be selected when one enables
support for ums command.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For the redundant environment configuration, env_sf_load still
contained duplicate code instead of using env_import_redund().
Simplify the code by only executing the load twice and delegating
everything else to env_import_redund.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For multiple env drivers to correctly implement fallback when
one environment fails to load (e.g. crc error), the return value
of env_import has to be propagated by all env driver's load
function.
Without this change, the first driver that succeeds to load an
environment with an invalid CRC return 0 (success) and no other
drivers are checked.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There is more common code in mmc, nand and ubi env drivers that
can be shared by moving to env_import_redund.
For this, a status/error value whether the buffers were loaded
are passed as additional parameters to env_import_redund.
Ideally, these are already returned to the env driver by the
storage driver. This is the case for mmc, nand and ubi, so for
this change, code deduplicated.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
env_import (and env_import_redund) currently return 1 on success
and 0 on error. However, they are only used from functions
returning 0 on success or a negative value on error.
Let's clean this up by making env_import and env_import_redund
return 0 on success and -EIO on error (as was the case for all
users before).
Users that cared for the return value are also updated. Funny
enough, this only affects onenand.c and sf.c
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
env_get_f calls env_get_char to load single characters from the
environment. However, the return value of env_get_char was not
checked for errors. Now if the env driver does not support the
.get_char call, env_get_f did not notice this and looped over the
whole size of the environment, calling env_get_char over 8000
times with the default settings, just to return an error in the
end.
Fix this by checking if env_get_char returns < 0.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The omapl138_lcdk platform is not a DA850 SoC so we need to select
SOC_DA8XX and not SOC_DA850, as it was before. It does however point
out a bit of a misnomer in how all of these PLL defines are named as
they are generic to DA8xx, not DA850 centric. Remove the 'if SOC_DA850'
under the defaults as these are simply the defaults. As SOC_DA8XX will
select SYS_DA850_DDR_INIT when needed, we do not need it under both SOC
options.
Fixes: 76e22222d3 ("Convert CONFIG_SYS_DV_CLKMODE et al to Kconfig")
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
This converts the following to Kconfig:
CONFIG_SYS_OMAP24_I2C_SLAVE
CONFIG_SYS_OMAP24_I2C_SPEED
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Paul Kocialkowski <contact@paulk.fr>
This converts the following to Kconfig:
CONFIG_SYS_DV_CLKMODE
CONFIG_SYS_DA850_PLL0_POSTDIV
CONFIG_SYS_DA850_PLL0_PLLDIV1
CONFIG_SYS_DA850_PLL0_PLLDIV2
CONFIG_SYS_DA850_PLL0_PLLDIV3
CONFIG_SYS_DA850_PLL0_PLLDIV4
CONFIG_SYS_DA850_PLL0_PLLDIV5
CONFIG_SYS_DA850_PLL0_PLLDIV6
CONFIG_SYS_DA850_PLL0_PLLDIV7
CONFIG_SYS_DA850_PLL1_POSTDIV
CONFIG_SYS_DA850_PLL1_PLLDIV1
CONFIG_SYS_DA850_PLL1_PLLDIV2
CONFIG_SYS_DA850_PLL1_PLLDIV3
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.
Signed-off-by: York Sun <york.sun@nxp.com>
DDR controllers always use binding register to determine the memory
space to perform data initialization. In case of controller interleaving,
the space is doubled, resulting twice long wait. It wasn't too bad until
the memory capacity increases. To reduce the wait time, reduce the
binding space to half and restore it after data initialization.
Three-way interleaving is no longer used and is removed.
Signed-off-by: York Sun <york.sun@nxp.com>
DDR4 RDIMM has some information in SPD to be used to calculate the
control words for register chip. The rest can be found from JEDEC
spec DDR4RCD02.
Signed-off-by: York Sun <york.sun@nxp.com>
On top of RDIMM support, add new register calculation to support
3DS RDIMMs. Only symmetrical 3DS is supported at this time.
Signed-off-by: York Sun <york.sun@nxp.com>
For DDR4, command/address delay in mode registers and parity latency
in timing config register are only needed for UDIMMs, but not RDIMMs.
Add additional register rcw_3 for DDR4 RDIMM. Fix mirrored bit for
dual rank RDIMMs. Set sdram_cfg_3[DIS_MRS_PAR] for RDIMMs. Fix
calculation of timing config registers. Use hexadecimal format for
printing RCW (register control word) registers.
Signed-off-by: York Sun <york.sun@nxp.com>
For for case of lazyapply method, API fdt_fixup_board_enet() gets
invoked before DPL being deployed. This leads to an issue that
fsl-mc fdt fixup status marked as fail and dprc driver didn't get
registered in linux boot.
Fixes this issue by calling fdt_fixup_board_enet() for case when
DPL is deployed successfully in lazyapply method.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
'select n' selects a constant symbol, which is meaningless and has no
effect. Maybe this was meant to be a 'default n', though bool and
tristate symbols already implicitly default to n.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which does more strict checking here:
kconfiglib.KconfigSyntaxError: board/google/Kconfig:34: Couldn't parse ' select n': expected nonconstant symbol
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The variable t_rfc is never used, so drop it. The variables ddr_wctl
and ddr_wcmd are only used in certain manual instances, so guard their
declaration by the same check as their use.
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on QEMU does not build ACPI table by ourself, instead it uses
the prebuilt ACPI table via the qfw interface. This implements the
qfw version of acpi_get_rsdp_addr() for setup_zimage().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present the acpi_rsdp_addr variable is directly referenced in
setup_zimage(). This changes to use an API for better encapsulation
and extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There is no JTAG symbol in the "Boot mode" choice. JTAG_MODE was
probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection JTAG (undefined) of <choice> (defined at arch/arm/cpu/armv8/zynqmp/Kconfig:107) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of ZynqMP boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moved ethernet PHY configs of Zynq boards
to respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Arasan NFC driver requires the self-init mode,
so it should select it.
Instead of having the config header define the macro,
it's cleaner to select the option at the Kconfig level.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the ecc address calculation before updating
to ecc register. The ecc address has to be calculated based on
page, oob and ecc sizes of the device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for ondie ecc. As of now
this adds support for micron parts which supports
ondie ecc.
Didn't found any better way to detect ondie ecc
support by a device except sorting out with
manufacture and device id's.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move common part of ecc structure initialization to
arasan_nand_init() routine.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only emmc functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
emmc support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new target which is called as mini configuration
with only nand functionality and other required basic features enabled.
This will be used to run in system with small footprint and needs
nand support.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DDR less systems are possible for configuration like mini qspi
and making DDR region as normal memory may cause speculative
access which results u-boot hang if DDR is absent. So, this
patch fixes the issue by not making DDR memory region
entry into MMU table.
Future solution is to prepare MMU table per memory node in dts instead
of hard code DDR addresses.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Drop the space before/after '<' and '>'; and
separate the entries to be a bit more readable.
Reported-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
BOOTCOMMAND is composed with distro_bootcmd but this variable is not
present. Enabling distro defaults setting is fixing it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There are two reasons for doing this change.
There is still !DM driver for xilinx soft gpio IP and especially it is
saving some space for memory constrained boards like cse (almost ~400B).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not enable DM_ETH/MMC if subsystems are not enabled.
This saves memory for memory constrained boards like cse.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to enable BLK by default for all boards which is just
increasing memory footprint for memory contrained boards like cse.
zc770s are also saving some space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Ethernet cable is not connected for xm011 that's why disable all
ethernet related configurations.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
It is good to see this string to make sure that u-boot which runs on the
board is the same which should run there.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the 8GB PCIe High area as device memory.
Also extend the DDR High area to cover the full 32GB range.
Signed-off-by: Anders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add check if boot_targets exists in environment and then
generate new_targets env accordingly. Performing strlen on
null address causes it to fail with exception if isolation
is enabled with DDR address zero as secure. It works with out
isolation enabled as zero is valid address but it may lead to
junk values in boot_targets.
This patch fixes the issue by checking return value of env_get
so that it generate boot_targets properly.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is fixing the following Warning:
arch/arm/mach-zynq/ps7_spl_init.c:133:24: warning: comparison between
signed and unsigned integer expressions [-Wsign-compare]
while (ioread(addr) < delay)
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
New field acpi_rsdp_addr, which has been introduced in boot protocol
v2.14 [1], in boot parameters tells kernel the exact address of RDSP
ACPI table. Knowing it increases robustness of the kernel by avoiding
in some cases traversal through a part of physical memory.
It will slightly reduce boot time by the same reason.
[1] See Linux kernel commit
2f74cbf ("x86/boot: Add the ACPI RSDP address to struct setup_header::acpi_rdsp_addr")
@ https://git.kernel.org/pub/scm/linux/kernel/git/tip/tip.git/commit/?id=2f74cbf
for the details.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: updated the kernel commit git URL and fixed one style issue]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The commit
20bfac0599 ("x86: zImage: add Intel MID platforms support")
introduced an assignment of subarch field in boot parameters, though
missed the right place of doing that. It doesn't matter if we have or
not a kernel command line supplied, we just set that field. Although
guard it by protocol version which supports it.
Fixes: 20bfac0599 ("x86: zImage: add Intel MID platforms support")
Cc: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The commit
eece493a7a ("cmd: qfw: bring ACPI generation code into qfw core")
moves ACPI related code to another file and missed an update of
references in acpi_table.c.
Do it now.
Fixes: eece493a7a ("cmd: qfw: bring ACPI generation code into qfw core")
Cc: Miao Yan <yanmiaobest@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ASL compiler warns:
ASL board/intel/edison/dsdt.asl
board/intel/edison/dsdt.asl.tmp 238: Method (_CRS, 0, NotSerialized)
Remark 2120 - Control Method should be made Serialized ^ (due to creation of named objects within)
Do as suggested by ASL compiler.
Fixes: 5d8c4ebd95 ("x86: tangier: Add Bluetooth to ACPI table")
Reported-by: Ferry Toth <fntoth@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
AES encryption in CBC mode, in most cases, must be used with random
initialization vector. Using the same key and initialization vector several
times is weak and must be avoided.
Added iv parameter to the aes_cbc_encrypt_blocks and aes_cbc_decrypt_blocks
functions for passing initialization vector.
Command 'aes' now also require the initialization vector parameter.
Signed-off-by: Andrey Mozzhuhin <amozzhuhin@yandex.ru>
Recent GCC versions warn if the format string is not a literal
because the compiler cannot check the argument validity at compile
time.
Commit 192bc6948b ("Fix GCC format-security errors and convert
sprintfs.") blindly replaced sprintf() with strcpy(), including
many cases where the format parameter is a string literal.
For the kconfig change:
sprintf(header, " ");
..., here the format parameter is a string literal " ", so it is
definitely equivalent to:
strcpy(header, " ");
Of course, if the 'header' did not have enough length for containing
" ", it would be a security problem, but another problem. (in this
case, the 'header' is 4 byte length buffer, so it is not a problem at
all.)
The kconfig code is kept as synced with Linux as possible, but this
change made the code out-of-sync for nothing. Just reverting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When printing a size_t value we need to use %zu for portability between
32bit and 64bit targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
When we have a driver that is used on both 32bit and 64bit targets and
we are talking about address space we cannot use u64 nor u32 and instead
need to use phys_addr_t.
Fixes: 377883f16d ("net: mvpp2x: fix phy connected to wrong mdio issue")
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Since 'commit f4fcba5c5b ("clk: implement clk_set_defaults()")'
STM32F4 family board can't boot.
Above patch calls clk_set_rate() for all nodes with assigned-clock-rates
property. Clock driver for STM32F family doesn't implement .set_rate
callback which make clk_set_defaults() exit on error and prevent board
to boot.
Fixes: f4fcba5c5b ("clk: implement clk_set_defaults()")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since 'commit af2f44267 ("fdc spl: use different BOARD_INIT MACRO for spl and tpl")'
board stm32f746-disco can't boot.
The macro CONFIG_IS_ENABLED() can't evaluate the value of
CONFIG_SPL_BOARD_INIT as it was defined in include/configs/stm32f746-disco.h
without attributed value.
Moving CONFIG_SPL_BOARD_INIT from stm32f746-disco.h to mach-stm32/Kconfig
fixes this issue.
Fixes: af2f44267 ("fdc spl: use different BOARD_INIT MACRO for spl and tpl")
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Commit 608b0c4ad4 ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4 ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Fix a typo in help output (awailable -> available).
Tidy the grammar - not the board connects to a port, we do.
While at it, be consistent in upper-casing the comments.
Fixes: eee4835d22 ("tools: Add Marvell recovery image download script")
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
minicom doesn't inherit the baudrate from stty but uses its own
defaults, such as for example 57600, whereas we expect 115200 here.
Explicitly tell minicom which baudrate to use.
Fixes: eee4835d22 ("tools: Add Marvell recovery image download script")
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The variable cfi_flash_num_flash_banks is defined iff
CONFIG_SYS_MAX_FLASH_BANKS_DETECT is defined, but it is used
unconditionally in the function cfi_flash_init_dm. This leads to a
undefined variable compile error when CONFIG_SYS_MAX_FLASH_BANKS_DETECT
is not defined, but DM is enabled.
Fix this by always defining the cfi_flash_num_flash_banks variable.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When long expressions surrounded by parentheses are split into multiple
lines, each consecutive line should be aligned with the corresponding
parenthesis. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Long lines (>80 characters) should be avoided where possible. Break up
some long lines where it's not detrimental to readability.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In a while loop in cfi_flash.c the array "start" is accessed at the index
"sector" before the index variable "sector" is bounds-checked, which
might lead to accesses beyond the bounds of the array.
Swap the order of the checks in the "&&" expression, so that the
short-circuit evaluation prevents out-of-bounds array accesses.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
checkpatch.pl complains about the spelling of ERR_TIMOUT. Since the
error is only used in a handful of files, we rename the error to
ERR_TIMEOUT.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Camel-case naming should be avoided. Rename two camel-case variables,
and fix their usage accordingly.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Strings should not be split accross multiple lines. Where possible and
not detrimental to readability, fix the instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
According to the C standard, pointer arithmetic for pointers of type
void is undefined behavior (the assumption that they're 8-bit wide is a
GCC-specific assumption). In the interest of keeping the code
standards-compliant, and also better communicate intent, switch all
void* variables where pointer arithmetic is used to u8* variables.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The condition in if statements should not be used for variable
assignment. Instead, the assignment should be done in a separate step
beforehand. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The opening brace of block statements should be attached to the
statement itself, and not be on a separate line.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
If in a loop, the if block in a if/else statement ends in a break, the
statements in the else blockcan be extracted, since the break stops the
execution.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In if/else statements, either both blocks (if and else) should have
braces or both blocks should not have braces, but mixed configurations
are discouraged. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
"==" and "!=" bind tighter than the boolean operators, so parentheses
around them in compound logical statements are unnecessary. Fix all
instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Comment blocks should end with a "*/" on a separate line, not with the
"*/" attached to the end of the last line of text. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
printf/debug statements should not include the file name as a hardcoded
string, but instead use the __func__ macro. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When splitting long logical statements across multiple lines, the
logical operators should be at the end of the lines. Fix all instances
where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Blocks with a single statement should not be enclosed in braces. Fix all
instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should be no consecutive blank lines, and no blank lines at the
end of blocks. But there should be blank lines between variable
declarations and code. Fix all instances where either occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should be spaces around operators, and no spaces between a cast
and the variable its being applied to. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
case statements should be at the same level of indent as the switch
keyword. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
When casting to a pointer type, the asterisk should be attached to the
type name, not separated by a space. Fix all instances where this
occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should not be additional spaces when nesting parentheses
("( (...) )"). Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
In a pointer declaration there should not be a space between the
asterisk and the pointer name. Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
There should not be a space between a function name and a parenthesis
("func (...)"). Fix all instances where this occurs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Patch queue for efi - 2018-01-28
This is the second part of patches for 2018.03-rc1, fixing
a few minor issues and adding a readme file for iSCSI booting.
The appended README explains how U-Boot and iPXE can be used
to boot a diskless system from an iSCSI SAN.
The maintainer for README.efi and README.iscsi is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: s/Adress/Address/]
Signed-off-by: Alexander Graf <agraf@suse.de>
Now that we have %pD support in vsprintf we should avoid separate
logic for printing device paths in other places.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In an image is loaded from memory we do not have a device path.
Do not install NULL as device path in this case.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When printing '%pD' with a value of NULL we want to output
'<NULL>'. But this requires copying to buf. Leave this
to string16.
A unit test is supplied which relies on EFI support in the sandbox.
The development for EFI support in the sandbox is currently in branch
u-boot-dm/efi-working. The branch lacks commit 6ea8b580f0 ("efi_loader:
correct DeviceNodeToText for media types"). Ater rebasing the aforementioned
branch on U-Boot v2018.01 and adding 256060e425 and this patch the test
is executed successfully.
Fixes: 256060e425 (vsprintf.c: add EFI device path printing)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a UEFI payload just returns instead of calling the Exit() callback,
we handle that in efi_do_enter() and call Exit on its behalf, so that
the loaded_image->exit_status value is correct.
We were missing that logic in StartImage(). Call it there too.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a better description for indent_string.
Fix a typo.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If 'bootefi hello' or 'bootefi selftest' can be executed depends on the
configuration.
If an invalid non-numeric 1st argument is passed to bootefi, e.g.
'bootefi hola', this string is converted to 0 and U-Boot jumps to
this typically invalid address.
With the patch the online help is shown instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
EFI calls are usually defined as asmlinkage. That means we pass all parameters
to functions via the stack x86_32.
On x86_64 however, we need to also stick to the MS ABI calling conventions,
which the EFIAPI define conveniently handles for us. Most EFI functions were
also marked with EFIAPI, except for the entry call.
So this patch adjusts all entry calls to use EFIAPI instead of the manual
asmlinkage attribute.
While at it, we also change the prototype of the entry point to return
efi_status_t instead of ulong, as this is the correct prototype definition.
Signed-off-by: Alexander Graf <agraf@suse.de>
---
v1 -> v2:
- Use efi_status_t in all occurences
We have 2 users of the EFI headers: efi_loader and the EFI stub. Efi_loader
always expects that the bitness of the definitions it uses is identical to
the execution.
The EFI stub however allows to run x86_64 U-Boot on 32bit EFI and the other
way around, so it allows for different bitness of EFI definitions and U-Boot
environment.
This patch explicitly requests via Kconfig that efi_loader can only be enabled
if the bitness is identical. Because we can run efi_loader on x86_64 without
EFI stub enabled, it also ensures that this case propagates the correct ABI
constraints.
Signed-off-by: Alexander Graf <agraf@suse.de>
The SOM has external pull-up resistors, so let's turn these off.
It was helping reduce some errors when running I2C1 @ 2.6MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
Selecting this option will reduce SPL boot time by approx. 6 ms
(e. g. with 70 bytes long banner string at 115200 baud).
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The serial drivers now depend on the pinctrl driver to determine whether
they are enabled. That means if a serial device wants to be used pre-reloc,
we also need the pinctrl device pre-reloc.
Adapt the pinctrl driver as well as dts overlay accordingly.
Signed-off-by: Alexander Graf <agraf@suse.de>
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Signed-off-by: Alexander Graf <agraf@suse.de>
It seems as if I have more interest in BCM2835 support than most others,
so I'll bite the bullet and declare myself maintainer. It'd be a shame
to leave that platform orphaned.
Signed-off-by: Alexander Graf <agraf@suse.de>
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x mini-uart is only really usable as U-Boot serial output
when it is muxed to the UART pins of the RPi pin header.
So fail probing in case it is not muxed correctly, as in that case
firmware did not initialize it properly either.
Signed-off-by: Alexander Graf <agraf@suse.de>
The serial initialization doesn't always quite work for me, so let's
always skip it for now. We know that firmware on the RPi initializes
us properly already.
Signed-off-by: Alexander Graf <agraf@suse.de>
Firmware on the Raspberry Pi family of devices can dynamically configure either
the PL011, Mini-UART or no device at all to be routed to the user accessible
UART pins.
That means we need to always include both drivers, because we can never be sure
which of the two serial devices firmware actually chooses to use.
Signed-off-by: Alexander Graf <agraf@suse.de>
We are switching to a model where a serial device doesn't even get probed when
it's not muxed properly, so we don't need device specific disabling
functionality anymore.
Signed-off-by: Alexander Graf <agraf@suse.de>
We are switching to a model where our board file can directly fail probing
of serial devices when they're not usable, so remove the current runtime
hack we have.
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently our serial device search chokes on the fact that the serial
probe function could fail. If it does, instead of searching for the next
usable serial device, it just quits.
This patch changes the fallback logic so that even when a serial device
was not probed correctly, we just try the next ones until we find one that
works.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
With driver model enabled in SPL, sdram_init() requires device tree
and malloc to be initialized.
Therefore call spl_early_init() in early_system_init().
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The BCM2835 family of SoCs has 2 different SD controllers: One based on
the SDHCI spec and a custom, home-grown one.
This patch implements a driver for the latter based on the Linux driver.
This is needed so that we can make use of device trees that assume driver
presence of both SD controllers.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
CONFIG_WALNUT was dropped in June 2017 in:
commit 98f705c9ce ("powerpc: remove 4xx support")
While at it, the related CONFIG_MACH_SPECIFIC and the have_of
and _machine variables are unused as well, so drop them too.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
libfdt_env.h is supposed to provide system-dependent defines.
scripts/dtc/libfdt/libfdt_env.h from upstream DTC is suitable
for user-space, so we should use this for USE_HOSTCC case.
For compiling U-Boot, we need to override such system-dependent
defines, so use <linux/libfdt_env.h> imported from Linux.
<libfdt.h> selects a proper one. Maybe, we should split header
inclusion completely, but I do not want too many patches at one.
I can rip off the include/libfdt_env.h from HOST_EXTRACFLAGS.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is tons of code duplication between lib/libfdt/libfdt.h and
scripts/dtc/libfdt/libfdt.h. Evacuate the U-Boot own code to
include/libfdt.h and remove lib/libfdt/libfdt.h.
For host tools, <libfdt.h> should include scripts/dtc/libfdt/libfdt.h,
which is already suitable for user-space.
For compiling U-Boot, <linux/libfdt.h> should be included because we
need a different libfdt_env.h .
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
libfdt_env.h exists to contain system-dependent defines:
- typedef of fdt*_t
- fdt*_to_cpu(), cpu_to_fdt*
working_fdt and FDT_RAMDISK_OVERHEAD are unrelated to the environment,
so they must get out of this header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several host-tools use "bool" type without including <stdbool.h>.
This relies on the crappy header inclusion chain.
tools/Makefile has the following line:
HOST_EXTRACFLAGS += -include $(srctree)/include/libfdt_env.h \
All host-tools are forced to include libfdt_env.h even if they are
totally unrelated to FDT. Then, <stdbool.h> is indirectly included
as follows:
include/libfdt_env.h
-> include/linux/types.h
-> <stdbool.h>
I am fixing this horrible crap. In advance, I need to add necessary
include directives explicitly. tools/fdtgrep.c needs more; <fctl.h>
for open() and <errno.h> for errno.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
I do not remember why, but this is apparently a file-copy mistake.
The file name is libfdt.h, but its content is that of libfdt_env.h
Re-import it from upstream Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only difference between scripts/dtc/libfdt/fdt_rw.c and
lib/libfdt/fdt_rw.c is fdt_remove_unused_strings().
It is only used by fdtgrep, so we do not need to compile it for U-Boot
image. Move it to tools/libfdt/fdw_rw.c so that lib/libfdt/fdt_rw.c
can be a wrapper of scripts/dtc/libfdt/fdt_rw.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit allows overriding the default assumption that the boot UBI
MTD partition is named 'UBI' and the UBI volume is 'boot'. A board
desiring to use a legacy or alternative NAND layout can now define the
following two extra environment variables:
bootubipart=<some_ubi_partition_name>
bootubivol=<some_ubi_volume_name>
EXAMPLE:
[include/configs/some_board.h]
---8<-------------------------------------------------------------------
[...]
#include <config_distro_defaults.h>
#define MEM_LAYOUT_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV
#define BOOT_TARGET_DEVICES(func) \
func(UBIFS, ubifs, 0)
#include <config_distro_bootcmd.h>
[...]
#define CONFIG_EXTRA_ENV_SETTINGS \
MEM_LAYOUT_ENV_SETTINGS \
"bootubivol=rootfs\0" \
"bootubipart=rootfs\0" \
BOOTENV
[...]
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Loading files stored with lzo compression from a btrfs filesystem was
producing unaligned memory accesses, which were causing a data abort
and a reset on an Orange Pi Zero.
The change in hash.c is not triggered by any error but follows the
same pattern. Please confirm.
Fixed according to doc/README.unaligned-memory-access.txt
Signed-off-by: Alberto Sánchez Molero <alsamolero@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
The backlight pwm-cell is 3.
This remove the warning in buildman:
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Property 'pwms', cell 3 is not a phandle reference in /backlight
arch/arm/dts/rk3126-evb.dtb: Warning (pwms_property): Missing property '#pwm-cells' in node /sram@10080400 or bad phandle (referred from /backlight:pwms[3])
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The set_parent implementations do not make sense when OF_PLATDATA is
enabled. We guard these against OF_PLATDATA and don't populate the
set_parent-op when this is the case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3288 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3288 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
implement the gmac clock set parent, but simply ignore the
others' set_rate() operation and return 0 to signal success.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GMAC in the RK3228 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3368-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The GMAC2IO in the RK3328 once again is identical to the incarnation in
the RK3288 and the RK3399, except for where some of the configuration
and control registers are located in the GRF.
This adds the RK3328-specific logic necessary to reuse this driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The rv1108 GMAC only support rmii interface, so need to add the
set_rmii() ops. Use the phy current interface to set rmii or
rgmii ops. At the same time, need to set the mac clock rate of
rmii with 50M, the clock rate of rgmii with 125M.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3399 CRU-node assigns rates to a number of clocks that are not
implemented in the RK3399 clock-driver (but which have been
sufficiently initialised from rkclk_init()): for these clocks, we
simply ignore the set_rate() operation and return 0 to signal success.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Linux uses the properties 'assigned-clocks', 'assigned-clock-parents'
and 'assigned-clock-rates' to configure the clock subsystem for use
with various peripheral nodes.
This implements clk_set_defaults() and hooks it up with the general
device probibin in drivers/core/device.c: when a new device is probed,
clk_set_defaults() will be called for it and will process the
properties mentioned above.
Note that this functionality is designed to fail gracefully (i.e. if a
clock-driver does not implement set_parent(), we simply accept this
and ignore the error) as not to break existing board-support.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Series-version: 2
Cover-letter:
clk: support assigned-clock, assigned-clock-parents, assigned-clock-rates
For various peripherals on Rockchip SoCs (e.g. for the Ethernet GMAC),
the parent-clock needs to be set via the DTS. This adds the required
plumbing and implements the GMAC case for the RK3399.
END
This implements the (newly added) set_parent() operation for the
RK3399 with a focus on allowing the RGMII clock parent to be
configured via the assigned-clock-parents property of the GMAC node.
This implementation supports only the GMAC (in fact only the RGMII
clock parent) and allows to set this clock's parent either to the
internal SCLK_GMAC or to an external clock input (identifiable by it
providing a 'clock-output-name' of "gmac_clkin").
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
The logic in clk_get_by_index() may be useful for other properties
than 'clocks': e.g. 'assigned-clocks' and 'assigned-clock-parents'
follows the same model.
This commit refactors clk_get_by_index() by introducing an internal
function clk_get_by_indexed_prop() that allows to specify the name
of the property to process. The original clk_get_by_index() call
is simply directed through this helper function with the property
name fixed to "clocks".
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
Clocks may support multiple parents: this change introduces an
optional operation on the clk-uclass to set a clock's parent.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: David Wu <david.wu@rock-chips.com>
Series-changes: 2
- Fixed David's email address.
PLLSAIP divider uses 2 bits (bits 16 and 17) into RCC_PLLSAICFGR
register, available combination are :
00: PLLSAIP = 2
01: PLLSAIP = 4
10: PLLSAIP = 6
11: PLLSAIP = 8
Previously, the divider value was incorrectly set to 6.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Since 7e0ed13 ("Convert ARCH_OMAP2PLUS boards' CONFIG_SYS_TEXT_BASE to
Kconfig"), a default SYS_TEXT_BASE was set for all ARCH_OMAP2PLUS devices.
CONFIG_ISW_ENTRY_ADDR is used to set SYS_TEXT_BASE in qspi boot.
Simplify this by directly assigning SYS_TEXT_BASE in the defconfig.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Several inline functions in this file reference undefined functions in
U-Boot. For example:
atomic-long.h:73:9: warning: implicit declaration of function
'atomic64_sub_and_test'
atomic-long.h:80:9: warning: implicit declaration of function
'atomic64_dec_and_test'
atomic-long.h:87:9: warning: implicit declaration of function
'atomic64_inc_and_test'
Handle this the same as the 32 bit build by wrapping these functions in
a __UBOOT__ check.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
This DT file comes from kernel v4.15, this board offers :
_ STM32F429NIH6 microcontroller
_ 4.3” color TFT LCD with resistive touchscreen (480 x 272 pixels)
_ Six 5 V power supply options:
Power jack
ST-LINK/V2 USB connector
User USB HS connector
User USB FS1 connector
User USB FS2 connector
Daughterboard
_ SAI Audio DAC, stereo audio jack which supports headset with
microphone
_ Stereo digital microphone, audio terminal connector used to connect
external speakers
_ 2 GBytes (or more) SDIO interface MicroSD card
_ RF EEPROM on I2 C compatible serial interface
_ RS-232 communication
_ IrDA transceiver
_ JTAG/SWD and ETM trace debug support, ST-LINK/V2 embedded
_ IEEE-802.3-2002 compliant Ethernet connector
_ Camera module
_ 8M x 32-bit SDRAM, 1M x 16-bit SRAM and 8M x 16-bit NOR Flash
_ Joystick with 4-directional control and selector
_ Reset, Wakeup and Tamper buttons
_ 4 color user LEDs
_ Extension connectors & memory connectors for daughterboard or
wrapping board
_ USB OTG HS and FS with Micro-AB connectors
_ RTC with backup battery
_ CAN2.0A/B compliant connection
_ Potentiometer
_ Motor control connector
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As clk_stm32f driver is able to retrieve HSE frequency from DT,
CONFIG_STM32_HSE_HZ becomes useless.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
All current STM32F4 supported boards uses a 8MHz external oscillator.
All current STM32F7 supported boards uses a 25MHz external oscillator.
In order to introduce the new stm32f429-evaluation board which uses a
25MHz external oscillator without creating a dedicated struct
stm32_clk_info for this board, retrieve the external oscillator
frequency from DT and set pll_m accordingly to obtain 1MHz for the VCO.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to retrieve the clk_hse fixed clock phandle in clk_stm32f driver,
add "u-boot,dm-pre-reloc" property in Uboot specific DT file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
compiling U-Boot with bosch_mpcxxxxd_sd_defconfig
drops warning:
arch/arm/lib/bootm-fdt.c: In function ‘arch_fixup_fdt’:
arch/arm/lib/bootm-fdt.c:37:6: warning: unused variable ‘ret’ [-Wunused-variable]
int ret = 0;
^~~
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
When in early SPL we make some secure ROM calls that can effect
DRAM, due to this it is more stable to store the args for these
calls in SRAM, but uninitialized and zero'd globals are placed
in BSS, located in DRAM. Force our args into the data section
which is in SRAM during SPL.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Clarify the computation precedence in two ternary operator
constructions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There are some typos in the documentation of some functions in read.h;
fix those.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Finally, make the mpc8xxx driver capable of handling more GPIO devices;
this entails adding a special case for the MPC5121 SoC, and adding a set
of new compatible strings.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Rename the Kconfig option, structures (and their members), as well as
functions of the mpc85xx driver to include mpc8xxx to reflect the more
generic usage.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
In preparation to making the MPC85xx GPIO driver useable for a broader
range of SoCs, rename the driver file.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Make the pca953x_gpio driver compatible with a live device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The call to hash_block in passwd_abort fails with error ENOSPC on some
systems. The reason is that the variable which specifies the size of the
buffer to contain the computed hash does not get initialized.
This patch initializes the variable with the size of the buffer.
Signed-off-by: Martin Etnestad <martin.etnestad@appeartv.com>
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add U-Boot DT extras for each SoC and board. This marks the required
nodes with u-boot,dm-pre-reloc to start clock and PRR early on while
avoiding modification of the DTs imported from Linux.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Stout board is not supported in Linux, so add a rudimentary DTS
for H2 Stout as a placeholder for when a proper DTS is available.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The Stout is already being shipped over, so proper DTS for both
U-Boot and Linux will happen once it's delivered :-)
Import the Renesas R8A7794 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7793 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7792 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7791 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the Renesas R8A7790 DTS and headers from upstream Linux kernel v4.15-rc8,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add DM capable code into the SH ethernet driver and support probing
both from DT and pdata. The legacy non-DM, non-DT support is retained
as there are still systems in the tree which are not DM or DT capable.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the legacy functions around, so that they can be wrapped in a
massive ifdef CONFIG_DM_ETH once DM support is added. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split sh_eth_init() function into smaller chunks, which can
be called from both DM and non-DM code while handling the
specifics of both configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pull out the code for writing MAC address into the NIC into a
separate function, so it can be reused by both DM and non-DM
code. This is done in preparation for DM support, which handles
MAC address programming separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Split sh_eth_recv into two functions, one which checks whether
a packet was received and one which handles the received packet.
This is done in preparation for DM support, which handles these
two parts separately.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Pass sh_eth_dev structure around instead of eth_device, since the
later is specific to the legacy networking support. This change is
done in preparation for the DM addition.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Add driver for the Renesas RCar PCIe controller present on Gen2 SoCs.
The PCIe on Gen2 is used both to connect external PCIe peripherals as
well as access the on-SoC USB EHCI controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
The current environment has been hardcoded to an offset that starts to be
an issue given the current size of our main U-Boot binary.
By implementing a custom environment location routine, we can always favor
the FAT-based environment, and fallback to the MMC if we don't find
something in the FAT partition. We also implement the same order when
saving the environment, so that hopefully we can slowly migrate the users
over to FAT-based environment and away from the raw MMC one.
Eventually, and hopefully before we reach that limit again, we will have
most of our users using that setup, and we'll be able to retire the raw
environment, and gain more room for the U-Boot binary.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we want to have multiple environments, we will need to initialise
all the environments since we don't know at init time what drivers might
fail when calling load.
Let's init all of them, and only consider for further operations the ones
that have not reported any errors at init time.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have everything in place to support multiple environment, let's
make sure the current code can use it.
The priority used between the various environment is the same one that was
used in the code previously.
At read / init times, the highest priority environment is going to be
detected, and we'll use the same one without lookup during writes. This
should implement the same behaviour than we currently have.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make the common code play a little nicer by removing all the extra output
in the standard case.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make MMC play a little nicer by removing all the extra \n and formatting
that is redundant with the global output.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Since we have global messages to indicate what's going on, the custom
messages in the environment drivers only make the output less readable.
Make FAT play a little nicer by removing all the extra \n and formatting
that is redundant with the global output.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we can have multiple environments now, it's better to provide a
decent indication on what environments were tried and which were the one to
fail and succeed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since we'll soon have support for multiple environments, the environment
saving message might end up being printed multiple times if the higher
priority environment cannot be used.
That might confuse the user, so let's make it explicit if the operation
failed or not.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In preparation for the multiple environment support, let's introduce two
new parameters to the environment driver lookup function: the priority and
operation.
The operation parameter is meant to identify, obviously, the operation you
might want to perform on the environment.
The priority is a number passed to identify the environment priority you
want to retrieve. The lowest priority parameter (0) will be the primary
source.
Combining the two parameters allow you to support multiple environments
through different priorities, and to change those priorities between read
and writes operations.
This is especially useful to implement migration mechanisms where you want
to always use the same environment first, be it to read or write, while the
common case is more likely to use the same environment it has read from to
write it to.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The env_driver_lookup_default and env_get_default_location functions are
about to get refactored to support loading from multiple environment.
The name is therefore not really well suited anymore. Drop the default
part to be a bit more relevant.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The nvedit command is the only user of env_driver_lookup_default outside of
the environment code itself, and it uses it only to print the environment
it's about to save to during env save.
As we're about to rework the environment to be able to handle multiple
environment sources, we might not have an idea of what environment backend
is going to be used before trying (and possibly failing for some).
Therefore, it makes sense to remove that message and move it to the
env_save function itself. As a side effect, we also can get rid of the call
to env_driver_lookup_default that is also about to get refactored.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have and use wait_for_bit_le32() available, the callers of
cm_write_with_phase() should not be casting values to u32 and instead we
expect a const void *, so provide that directly.
Fixes: 48263504c8 ("wait_bit: use wait_for_bit_le32 and remove wait_for_bit")
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC environment offset is getting very close to the end of the U-Boot
binary now. Since we want to make sure this will not overflow, add a size
limit in the board for arm64. arm32 has already that limit enforced in our
custom image generation.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The make macro to check if the binary exceeds the board size limit is not
called. Make sure that is the case.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this option that is not critical until we can adress the issue
properly.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunXi arm64 build has overflown, leading to the main U-boot binary
overwriting the environment when flashing the new image, or even worse,
overwriting itself when we're calling saveenv.
Disable this command that is not critical until we can adress the issue
properly.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The DFU code relies on the HASH config option. Make sure it is always there
by selecting it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add option to set spi controller clock frequency via device tree
using standard clock bindings.
Define dw_spi_get_clk function as 'weak' as some targets
(like SOCFPGA_GEN5 and SOCFPGA_ARRIA10) don't use standard clock API
and implement dw_spi_get_clk their own way in their clock manager.
Get rid of clock_manager.h include as we don't use
cm_get_spi_controller_clk_hz function anymore. (we use redefined
dw_spi_get_clk in SOCFPGA clock managers instead)
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Implement dw_spi_get_clk function to override its weak
implementation in designware_spi.c driver.
We need this change to get rid of cm_get_spi_controller_clk_hz
function and clock_manager.h include in designware_spi.c driver.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
ehci_writel() swaps the arguments for address and value. One call
in ehci-mxs ignores that.
This fixes the warning:
drivers/usb/host/ehci-mxs.c: In function ?ehci_hcd_stop?:
drivers/usb/host/ehci-mxs.c:159:19: error: initialization makes integer from pointer without a cast [-Werror=int-conversion]
ehci_writel(tmp, &hcor->or_usbcmd);
^
arch/arm/include/asm/io.h:117:34: note: in definition of macro ?writel?
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/usb/host/ehci-mxs.c:159:2: note: in expansion of macro ?ehci_writel?
^~~~~~~~~~~
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Bool initializations should use true and false.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
This prevents the following ENOMEM:
Error binding driver 'bmips_cpu': -12
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the
final 0x00 byte which ends the .relocs section seems to be skipped &
left in flash as 0xff unless the data contained in the .mcs is padded
out to a 16 byte boundary. Without our final zero byte relocation will
fail with an error about a spurious reloc:
Avoid this problem by padding out the data in the .mcs file to a 16 byte
boundary using srec_cat's -range-pad functionality.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This driver has been using printf() including filename since it was
added. Convert to using debug() instead.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Currently, socfpga_common.h does not allow configurations without
network support. This is because CONFIG_CMD_PXE is defined in this
file and distro mode has DHCP hard-coded as available.
Fix this by moving CONFIG_CMD_PXE and CONFIG_MENU to the defconfigs
and by making DHCP optional in BOOT_TARGET_DEVICES(func).
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Pull code which is common for RCar Gen2 and RCar Gen3 into
separate source file. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add Kconfig entries for each SoC clock table, so they can be
compiled in or out at build time. This can reduce the size of
the binary if desired.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The Gen2 requires setting RMSTPCR before booting, while on Gen3 this
is thus far always zero. Split the tables so the RMSTPCR can be set
too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Not all SoCs have the same PLL configuration options,
so make those PLL configuraion tables per-SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Split the massive driver into smaller per-SoC drivers and pull the
common code into a separate file. This would allow configuring out
unnecessary clock drivers once the Kconfig changes are in and also
allow adding more clock tables easily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use the common RCAR_GEN2 config option instead of enumerating
each SoC and having a lengthy ifdef clause. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace fdtdec_get_addr() with devfdt_get_addr() as the later one is
the current recommended practice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Convert these configuration options to Kconfig, update board defconfigs
and drop them from whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out u-boot extras into dtsi files to make synchronization of DTS
from Linux kernel as easy as a simple copy. All the U-Boot extras are
now in *-u-boot.dts* files instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Import the RCar Gen3 DTS and headers from upstream Linux kernel v4.14,
commit bebc6082da0a9f5d47a1ea2edc099bf671058bd4 . This includes both M3
and H3 ULCB and Salvator-X boards.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When clock is enabling, it's assigned to 0 as mmc->clock.
Then it can't initialize any card.
Fix to assign to correct clock value as mmc->cfg->f_min or f_max.
Fixes: 9546eb92cb ("mmc: fix the wrong disabling clock")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
exynos5422 has the s2mps11 PMIC.
s2mps11 pmic has the 10-BUCK and 38-LDO regulators.
Each IP and devices in exynos5422 can be controlled by each regulators.
This patch is support for s2mps11 regulator driver.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Make flash writes 32 bit aligned by using bounce buffers to deal with
non 32 bit aligned buffers.
This is required because as per TI K2G TRM[1], the external master is
only permitted to issue 32-bit data interface writes until the last word
of an indirect transfer. Otherwise indirect writes is known to fail
sometimes.
[1] http://www.ti.com/lit/ug/spruhy8g/spruhy8g.pdf
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This reverts commit 57897c13de.
Using bounce_buf.c to handle non-DMA alignment problems is bad as
bounce_buf.c does cache manipulations which is not required. Therefore
revert this patch in favour of local bounce buffer solution in the next
patch.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This reverts commit b63b46313e.
This commit changed cadence_qspi_apb to use bouncebuf.c, which invalidates
the data cache after reading. This is meant for dma transfers only and
breaks the cadence_qspi driver which copies via cpu only: data that is
copied by the cpu is in cache only and the cache invalidation at the end
throws away this data.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jason Rush <jarush@gmail.com>
Acked-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Adopt the Linux DT bindings. This also fixes an issue
with the indaddrtrig register on the Cadence QSPI
device being programmed with the wrong value for the
socfpga arch.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
Erratum NO. FE-9144572: The device SPI interface supports frequencies of
up to 50 MHz. However, due to this erratum, when the device core clock
is 250 MHz and the SPI interfaces is configured for 50MHz SPI clock and
CPOL=CPHA=1 there might occur data corruption on reads from the SPI
device.
Implement the workaround by setting the TMISO_SAMPLE value to 0x2
in the timing1 register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
spi_flash_probe_tail is now only called from spi_flash_probe, hence we
can merge its body into spi_flash_probe.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Previous patches removed the last usages of this config variable, so
that it is now obsolete.
This patch removes it from the whitelist.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
A previous patch removed the spi_flash_probe_fdt function, which
contained the last call of the spi_setup_slave_fdt function, which is
now equally obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Commit ba45756 ("dm: x86: spi: Convert ICH SPI driver to driver model")
removed the last usage of the spi_flash_probe_fdt function, rendering it
obsolete.
This patch removes the function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
0efc024 ("spi_flash: Add spi_flash_probe_fdt() to locate SPI by FDT
node") added a helper function spi_base_setup_slave_fdt to to set up a
SPI slave from a given FDT blob. The only user was the exynos SPI
driver.
But commit 73186c9 ("dm: exynos: Convert SPI to driver model") removed
the use of this function, hence rendering it obsolete.
Remove this function, as well as the CONFIG_OF_SPI option, which guarded
only this function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
This patch fixes a printf specifier style violation, reduces the scope
of a variable, and turns a void pointer that is used with pointer
arithmetic into a u8 pointer.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Command bytes are part of the written bytes and they should be taken into
account when sending a spi transfer.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For some SPI controllers it's not possible to keep the CS active between
transfers and they are limited to a known number of bytes.
This splits spi_flash reads into different iterations in order to respect
the SPI controller limits.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add 8/16/32 bits and BE/LE versions of wait_for_bit.
This is needed for reading registers that are not aligned to 32 bits, and for
Big Endian platforms.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Change all coldfire arch files to use CONFIG_DISPLAY_CPUINFO.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Reviewed-by: Tom Rini <trini@konsulko.com>
---
Changes for v2:
- update common/Kconfig to add M68K to the default y list
Add macro QIXIS_LBMAP_EMMC, QIXIS_LBMAP_IFC, QIXIS_RCW_SRC_IFC,
QIXIS_RCW_SRC_EMMC to enable IFC and eMMC as boot sources for
qixis commands.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
[YS: Modify subject and add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The hash command function were not flushing the dcache before passing data
to CAAM/DMA and not invalidating the dcache when getting data back.
Due the data cache incoherency, HW accelerated hash commands used to fail
with CAAM errors like "Invalid KEY Command".
Check if pbuf and pout buffers are properly aligned to the cache line size
and flush/invalidate the memory regions to address this issue.
This solution is based in a previous work from Clemens Gruber in
commit 598e9dccc7 ("crypto/fsl: fix BLOB encapsulation and
decapsulation")
Reported-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The current GPL only licensing on the device trees makes it very
impractical for other software components licensed under another
license.
To make it easier to reuse them, re-license the the device trees for
Freescale (now NXP) SoCs and boards under GPLv2+/X11 dual license.
Same trend is followed in linux.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Mingkai Hu <mingkai.hu@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When VID feature is supported, check the contents of fuse register
and configure DDR operate at 0.9v.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sets DDR configuration parameter cdr1 before all other settings
to support case 0.9v VDD is enabled for some SoCs
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Patch queue for efi - 2018-01-23
This time around we have a lot of EFI patches from Heinrich.
Highlights are:
- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements
This converts the following to Kconfig:
CONFIG_SOC_DA8XX
CONFIG_SOC_DA850
CONFIG_DA850_LOWLEVEL
CONFIG_MACH_DAVINCI_DA850_EVM
CONFIG_SYS_DA850_PLL_INIT
CONFIG_SYS_DA850_DDR_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: David Lechner <david@lechnology.com>
[trini: Rework CONFIG_SYS_DA850_PLL_INIT so it's selected on SOC_DA8XX]
Signed-off-by: Tom Rini <trini@konsulko.com>
Some messages are only useful if an error occurs.
Fix a use after free.
Add a missing free.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Create device path nodes for UCLASS_ETH udevices.
Create device path nodes of block device children of UCLASS_MMC udevices.
Consistently use debug for unsupported nodes.
Set the log level to error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Fix build failure by adding #ifdef CONFIG_DM_ETH]
Signed-off-by: Alexander Graf <agraf@suse.de>
This test checks the driver for block IO devices.
A disk image is created in memory.
A handle is created for the new block IO device.
The block I/O protocol is installed on the handle.
ConnectController is used to setup partitions and to install the simple
file protocol.
A known file is read from the file system and verified.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices
For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol
The uclass provides the bind, start, and stop entry points for the driver
binding protocol.
In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.
The EFI block driver binds to controllers implementing the block io
protocol.
When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.
The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.
A usage example is as following:
U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.
Now the EFI block driver installs the partitions with the simple file
protocol.
iPXE uses the simple file protocol to load Grub or the Linux Kernel.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len]
Signed-off-by: Alexander Graf <agraf@suse.de>
The device tree is needed at runtime. So we have to store it in
EFI_RUNTIME_SERVICES_DATA memory.
The UEFI spec recommends to store all configuration tables in
EFI_RUNTIME_SERVICES_DATA memory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This pair of tests checks the StartImage boot service.
Each test loads an EFI application into memory and starts it.
One returns by calling the Exit boot service. The other returns directly.
The tests are not built on x86_64 because the relocation code for the efi
binary cannot be created.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch lets the implementation of ExitBootServices conform to
the UEFI standard.
The timer events must be disabled before calling the notification
functions of the exit boot services events.
The boot services must be disabled in the system table.
The handles in the system table should be defined as efi_handle_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In ExitBootServices we need to signal events irrespective of the current
TPL level. A new parameter check_tpl is added to efi_signal_event().
Function efi_console_timer_notify() gets some comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
On a block device and its partitions the same protocols can be
installed. To tell the apart we can use the type of the last
node of the device path which is not the end node.
The patch provides a utility function to find this last node.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the revision constants.
Depending on the revision additional fields are needed in the
media descriptor.
Use efi_uintn_t for number of bytes to read or write.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Up to now we have been using efi_disk_create_partitions() to create
partitions for block devices that existed before starting an EFI
application.
We need to call it for block devices created by EFI
applications at run time. The EFI application will define the
handle for the block device and install a device path protocol
on it. We have to use this device path as stem for the partition
device paths.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide new function efi_dp_part_node() to create a device
node for a partition.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The GUID of the EFI_BLOCK_IO_PROTOCOL is needed in different code
parts. To avoid duplication make efi_block_io_guid a global symbol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The interface type name can be used to look up the interface type.
Don't confound it with the driver name which may be different.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The calling convention for the entry point of an EFI image
is always 'asmlinkage'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Check if the device tree and the SMBIOS table are available.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The category of memory allocated for an EFI image should depend on
its type (application, bootime service driver, runtime service driver).
Our helloworld.efi built on arm64 has an illegal image type. Treat it
like an EFI application.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use %pD to print the device path instead of its address when
entering efi_load_image.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In contrast to the description the code did not split the device
path into device part and file part.
The code should use the installed protocol and not refer to the
internal structure of the the disk object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When installing the the simple file system protocol we have to path
the address of the structure and not the address of a pointer to the
structure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
For the construction of device paths we need to call the
AllocatePool service. We should not ignore if it fails due to an
out of memory situation.
This patch changes the device path functions to return NULL if
the memory allocation fails.
Additional patches will be needed to fix the callers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We should consistently use the efi_handle_t typedef when
referring to handles.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This unit test checks the following protocol services:
ConnectController, DisconnectController,
InstallProtocol, UninstallProtocol,
OpenProtocol, CloseProtcol, OpenProtocolInformation
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The installation of UninstallProtocol is functional now.
So we do not expect errors when calling it.
Call UninstallProtocol with correct level of indirection
for parameter handle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The installation of UninstallProtocols is functional now.
So we do not expect errors when calling it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The UninstallProtocol boot service should first try to
disconnect controllers that have been connected with
EFI_OPEN_PROTOCOL_BY_DRIVER.
If the protocol is still opened by an agent, it should be
closed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Unfortunately we need a forward declaration because both
OpenProtocol and CloseProtocol have to call DisconnectController.
And DisconnectController calls both OpenProtcol and CloseProtocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Handles should be passed as efi_handle_t and not as void *.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement the ConnectController boot service.
A unit test is supplied in a subsequent patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When a device path protocol is installed write the device
path to the console in debug mode.
For printing the new macro EFI_PRINT is used, which can be reused
for future diagnostic output.
Remove unused EFI_PRINT_GUID macro
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_open_protocol_information provides the agent and controller
handles as well as the attributes and open count of an protocol
on a handle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix counting error]
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_open_protocol and efi_close_protocol have to keep track of
opened protocols.
Check if the protocol was opened for the same agent and
controller.
Remove all open protocol information for this pair.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_open_protocol has to keep track of opened protocols.
OpenProtocol enters the agent and controller handle
information into this list.
A unit test is supplied with a subsequent patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a list of open protocol infos to each protocol of a handle.
Provide helper functions to access the list items.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
CloseProtocol cannot be called without agent handle.
There is no need to close the device path protocol if
it has been opened without agent handle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Replace list_for_each_safe() and list_entry() by
list_for_each_entry_safe().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add color coding to output:
test section blue
success green
errors red
todo yellow
summary white
others light gray
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
[agraf: Fold in move of set_attribute before the print]
Signed-off-by: Alexander Graf <agraf@suse.de>
For testing EFI disk management we need an in-memory image of
a disk.
The tool file2include converts a file to a C include. The file
is separated into strings of 8 bytes. Only the non-zero strings
are written to the include. The output format has been designed
to maintain readability.
#define EFI_ST_DISK_IMG { 0x00010000, { \
{0x000001b8, "\x94\x37\x69\xfc\x00\x00\x00\x00"}, /* .7i..... */ \
{0x000001c0, "\x02\x00\x83\x02\x02\x00\x01\x00"}, /* ........ */ \
{0x000001c8, "\x00\x00\x7f\x00\x00\x00\x00\x00"}, /* ........ */ \
{0x000001f8, "\x00\x00\x00\x00\x00\x00\x55\xaa"}, /* ......U. */ \
...
{0x00006000, "\x48\x65\x6c\x6c\x6f\x20\x77\x6f"}, /* Hello wo */ \
{0x00006008, "\x72\x6c\x64\x21\x0a\x00\x00\x00"}, /* rld!.... */ \
{0, NULL} } }
As the disk image needed for testing contains mostly zeroes a high
compression ratio can be attained.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Avoid a failed assertion when an EFI app calls an EFI app.
Avoid that the indent level increases when calling 'bootefi hello'
repeatedly.
Avoid negative indent level when an EFI app calls an EFI app that
calls an EFI app (e.g. iPXE loads grub which starts the kernel).
Return the status code of a loaded image that returns without
calling the Exit boot service.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
For debugging efi_loader we need the capability to print EFI
device paths. With this patch we can write:
debug("device path: %pD", dp);
A possible output would be
device path: /MemoryMapped(0x0,0x3ff93a82,0x3ff93a82)
This enhancement is not available when building without EFI support
and neither in the SPL nor in the API example.
A test is provided. It can be executed in the sandbox with command
ut_print.
The development for EFI support in the sandbox is currently in
branch u-boot-dm/efi-working. The branch currently lacks
commit 6ea8b580f0 ("efi_loader: correct DeviceNodeToText
for media types"). Ater rebasing the aforementioned branch on
U-Boot v2018.01 the test is executed successfully.
Without EFI support in the sandbox the test is simply skipped.
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Without the patch a device path consisting only of an end node is
displayed as '/UNKNOWN(007f,00ff)'. It should be displayed as '/'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
lib/efi* indicates files efi* in directory lib.
lib/efi*/ indicates all files in directories lib/efi*.
Fixes: 623b3a5797 efi_selftest: provide an EFI selftest application
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Device paths can be very long. Due to a limited output buffer
the output for device paths is cut off. We can avoid this by
directly calling the boottime service with the the device path
string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Remove coloring code change]
Signed-off-by: Alexander Graf <agraf@suse.de>
In the task priority levels test debug output is written even if no
failure is detected.
Remove this distracting output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the event services test debug output is written even if no
failure is detected.
Remove this distracting output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
virt_size is of type unsigned long.
So it should be printed with %ul.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add comments describing memory functions.
Fix the formatting of a function declaration.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
As the U-Boot is compiled with -fshort-wchar we can define
the firmware vendor constant as wide string.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Correctly create the device path for IDE and SCSI disks.
Support for SATA remains to be done in a future patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When creating the device path of a block device it has to
comprise the block device itself and should not end at
its parent.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Make it select FS_FAT as well, because if it's not selected, enabling
ENV_IS_IN_FAT causes a Kconfig warning:
warning: (ENV_IS_IN_FAT) selects FAT_WRITE which has unmet direct dependencies (FS_FAT)
This also allows dropping some code from config_fallbacks.
Also drop the unnecessary help text about having to enable
CONFIG_FAT_WRITE - Kconfig automatically handles that.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_HCD
CONFIG_USB_MUSB_UDC
CONFIG_USB_DAVINCI
CONFIG_USB_OMAP3
CONFIG_USB_DA8XX
CONFIG_USB_AM35X
Signed-off-by: Adam Ford <aford173@gmail.com>
This converts the following to Kconfig:
CONFIG_USB_MUSB_OMAP2PLUS
CONFIG_USB_MUSB_AM35X
CONFIG_USB_MUSB_DSPS
CONFIG_USB_MUSB_PIO_ONLY
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
flags member of struct timing was not initialized,
this took to unpredictable behaviour of display flags,
such DISPLAY_FLAGS_HSYNC_HIGH instead of _LOW etc.
Init timing->flags = 0
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Commit 4f425280fa ("mmc: fsl_esdhc: Allow all supported prescaler
values") made it possible to set SYSCTL.SDCLKFS to 0 in SDR mode on
i.MX, thus bypassing the SD clock frequency prescaler, in order to be
able to get higher SD clock frequencies in some contexts. However, that
commit missed the fact that this value is illegal on the eSDHCv3
instance of the i.MX53. This seems to be the only exception on i.MX,
this value being legal even for the eSDHCv2 instances of the i.MX53.
Fix this issue by changing the minimum prescaler value for the single
instance of the i.MX53 eSDHCv3 controller.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
When power is off, clock is not disabling.
Because it's passed to 1, mmc->clock should be set to f_min value.
Some drivers can't initialize the eMMC/SD card with current status.
This patch is to fix the disabling clock value to 0.
Fixes: 2e7410d76a ("mmc: disable the mmc clock during power off")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Guillaume GARDET <guillaume.gardet@free.fr>
Tested-by: Anand Moon <linux.amoon@gmail.com>
During the tuning, drivers repeat data transfer, changing timing
parameters in the controller hardware. So, the tuning commands
(CMD19 for SD, CMD21 for eMMC) fail, and this is not a problem
at all.
Showing "Error detected..." in normal operation just make users
upset. This should not be shown.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This line overwrites host_cap that has been set by drivers and/or
helpers like mmc_of_parse(). Accumulate capabilities flags.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
You must fix your DT if it specifies insane bus-width, for example,
bus-width = <3>;
debug() is not displayed in usual configuration, so people will not
even notice weirdness. Use dev_err() instead, then let it fail.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
mmc_of_parse() in U-Boot is a pussy helper; it sets cfg->f_max to
52MHz even if DT does not provide "max-frequency" at all. This can
overwrite cfg->f_max that may have been set to a reasonable default.
As the DT binding says, "max-frequency" is an optional property.
Do nothing if DT does not specify it. This is the behavior of
mmc_of_parse() in Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
dev_read_u32_default() always returns something even when the property
is missing. So, it is impossible to do nothing in the case. One
solution is to use ofnode_read_u32() instead, but adding dev_read_u32()
will be helpful.
BTW, Linux has an equvalent function, device_property_read_u32();
it is clearer that it reads a property. I cannot understand the
behavior of dev_read_u32() from its name.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix some style violations in fdtdec.c, and reduce the scope of some
variables.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Judging from its name and parameters, device_is_compatible looks like it
is compatible with a live device tree, but it actually isn't.
Make it compatible with a live device tree.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
There are some whitespace-related style violations in read.c; fix those.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The Makefile entries in the clk driver directory were not alphabetically
sorted. Correct this.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The clk uclass was converted to support a live device tree recently,
hence the global data pointer declarations are no longer needed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
checkpatch.pl complains that the clk_ops structures used in clk-uclass.c
ought to be const, so we mark them as const.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Sync with Linux commit 30a7acd573899fd8b("Linux 4.15-rc6")
to use enum pin_config_param.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
get_maintainer.pl quotes names which it considers unsafe, i.e. anything
containing [^a-zA-Z0-9_ \-]. This confuses patman, it will duplicate
addresses which are also in Series-to/cc. Strip the quotes.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function dev_read_addr calls ofnode_get_addr_index in the live tree
case, which does not apply bus translations to the address read from the
device tree. This results in illegal addresses on boards that rely on
bus translations being applied.
Fix this situation by applying bus translations in the live tree case as
well.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Tested-by: Stephen Warren <swarren@nvidia.com>
Now the u-boot spi image is greater than 0x90000, increase the same in
env during spi erase.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
A 2 line help entry for a new Kconfig entry is, at this time, sufficient
in some cases, so lets drop that warning for now.
Signed-off-by: Tom Rini <trini@konsulko.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
Now this driver is used across stm32f4, stm32f7 and stm32h7
SoCs family, give it a generic name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Last users of the following macros (for n = 0..7) were removed in
commit 5b8e76c35e ("powerpc, 8xx: remove support for 8xx"):
CONFIG_SYS_PCMCIA_PBRn
CONFIG_SYS_PCMCIA_PORn
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
It's mostly obvious, except that QEMU is annoying and requires an
explicit '-cpu cortex-a57' (or some other 64-bit core) to actually run
in 64-bit mode.
While at it, remove the references to setting the ARCH environment
variable; that is not used in U-Boot.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The signing certificate name is always 15 chars long, but need not be
null terminated. One solution is then to use printf precision modifiers
to only print this many chars ("%.15s"), but tiny printf does not support
this, so lets just drop printing the cert name for now.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Fix the size calculation in the verify boot. The header size
should be subtracted from the image size, not be assigned to
the image size.
Fixes: 0830d72bb9 ("arm: am33xx: security: adds auth support for encrypted images")
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
CONFIG_OF_EMBED in particular is needed to allow the Raspberry Pi
firmware to pass the DTB to U-Boot and on to the kernel.
Signed-off-by: Drew Moseley <drew.moseley@northern.tech>
This commit adds UBIFS_NAND to BOOT_TARGET_DEVICES. This will
allow the kernel zImage to be loaded from '/boot/zImage' in UBIFS
(ubi0:rootfs).
Additionally update the *_MMC devices to also load kernel image from
the MMC 0:2 EXT4 file system.
DISTRO_DEFAULTS Setup
=====================
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:2 /boot/zImage and run mmcbootz
[fallback 2] Check MMC 0:2 /boot/uImage and run mmcboot
[fallback 3] Check NAND UBIFS /boot/zImage and run nandbootubifs
[fallback 4] Check NAND partitions and run nandboot
The following "extlinux.conf" can be used to load images in the
top-level of the MMC 0:1 FAT partition.
[MMC(0:1)/extlinux/extlinux.conf]
---8<-------------------------------------------------------------------
default omap3-evm
label omap3-evm
kernel /zImage
fdt /omap3-evm.dtb
append console=ttyO0,115200n8 root=/dev/mmcblk0p2 rw rootfstype=ext4 rootwait
---8<-------------------------------------------------------------------
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
initr_mem() is already enclosed by
#if defined(CONFIG_PRAM)
#endif
So there is no need to check CONFIG_PRAM again inside the
function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The command portion of the GPIO driver can only be used in full SPL so
re-work to guard the command related portions and mark it as static.
Cc: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Change help description to match the style of the other U-Boot commands
and get rid of the leading whitespace.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The message "reading %s\n" may be interesting when
debugging but otherwise it is superfluous.
Only output the message when debugging.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The message
"** %s shorter than offset + len **\n"
may be interesting when debugging but it does not indicate an
error.
So we should not write it if we are not in debug mode.
Fixes: 7a3e70cfd8 fs/fs.c: read up to EOF when len would read past EOF
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds OMAP3 BeagleBoard devicetree files from
Linux v4.15-rc5. This includes standard OMAP34XX board revisions as
well as the 'xM' which is OMAP36XX.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Keystone and DRA7 based TI platforms uses same
EMIF memory controller. cmd_ddr3 command is customized
for keystone platforms, make it generic so that it can
be re used for DRA7 platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Move cmd_ddr3 to cmd/ti in order to make
it build for non-keystone TI platforms.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rename to ddr3.c not cmd_ddr3.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
For data integrity, the EMIF1 supports ECC on the data
written or read from the SDRAM. Add support for enabling
ECC support in EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
This is a slight difference in emif_ddr_phy_status register offsets for
DRA7xx EMIF and older versions. And ecc registers are available only
in DRA7xx EMIC. Add support for this difference and ecc registers.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for simple memory fill operation. With large data sizes
it is much faster to use EDMA for memory fill rather than CPU.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
I'm working on a v2 patch to add support for a board named pdu001. Its
Linux DTS file uses the include file added by this patch. To keep Linux
and U-Boot DTS files in sync U-Boot requires a copy of this file,
although there is no driver for NXP's PCA9532 i2c LED driver chip (yet).
Signed-off-by: Felix Brack <fb@ltec.ch>
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DPLL DRR doesn't have an M4 divider. But the clock driver is trying
to configure M4 divider as 4(writing into a reserved register).
Fixing it by making M4 divider as -1.
Reported-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The size field in GP header that is expected by ROM is size of the
image + size of the header. But omapimage tool is updating size
as image size + 2 * header size. Remove this extra header size bytes.
Reported-by: Denys Dmytriyenko <denys@ti.com>
Debugged-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
omap_hsmmc driver uses "|" in a couple of places for disabling a bit.
While it's okay to use it in "mmc_reg_out" (since mmc_reg_out has a
_mask_ argument to take care of resetting a bit), it's incorrectly used
for resetting flags in "omap_hsmmc_send_cmd".
Fix it here by using "&= ~()" to reset a bit.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of sending STOP TRANSMISSION command from MMC core, enable
the auto command feature so that the Host Controller issues CMD12
automatically when last block transfer is completed.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The omap hsmmc host controller can have the ADMA2 feature. It brings better
read and write throughput.
On most SOC, the capability is read from the hl_hwinfo register. On OMAP3,
DMA support is compiled out.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the calculation for tWR and tPD. This improves the DDR refresh
interval and brings the initialization into line with the binary blobs
currently being supplied by Marvell.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The RD_SAMPLE_DELAY field is 5 bits so it needs to be masked with 0x1f
instead of 0xf. Rather than checking the read sample delay for all DDR
chip selects use the values for the chip selects that are actually
configured. Finally continue searching for the max_phase value even if the
current read_sample is the same as the max_read_sample.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The ternary operation had the HIGH/LOW values the
wrong way round. Update it to use the correct value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
When using only a single DDR chip select only assert M_ODT[0] on write.
Do not assert it on read and do not assert M_ODT[1] at all. Also set
tODT_OFF_WR to 0x9 which contradicts the recommendation from the
functional spec but is what Marvell's binary training blob does and
seems to give better results when ODT is active during writes.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Even though in production uImage usually is quite small as
it contains just Linux kernel image during development it might
be pretty convenient to have root-FS built into the same image.
That makes uImage much larger but given on our dev platforms we have
quite a lot of DDR (> 512 MiB) we may afford loading huge uImages.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is useful to make sure no stale data exists in caches after bootloaders.
The worst thing could be some lines of cache were locked in a bootloader
for example during DDR recalibration and never unlocked. This may lead
to really unpredictable issues later down the line.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Update default AXI, TUN, ARC clock set options:
instead of changing only IDIV divider settings adjust also domain PLL
settings.
Add support of TUN_ROM and TUN_PWM clocks (subclocks of TUNN_PLL)
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
As HSDK is a development board it is better to hang on panic instead of
reset the board when panic occurs. That way we preserve a state of HW
for possibility to do post-mortem debug via JTAG.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We'd like to keep IOC HW at the same state as t is right after reset when we
start Linux kernel so there will be no re-configuration of IOC on the go.
The point is U-Boot doesn't benefit a lot from IOC as it doesn't do a
lot of DMA operations especially on multiple cores simultaneously.
At the same time re-configuration of IOC in run-time might become quite
a tricky experience because we need to make sure there're no DMA
trannsactions in flight otherwise unexpected consequencses might affect
us much later and debugging those kinds of issues will be a real
nightmare.
That said let's make our life easier a little bit.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Previous SLC management implementation is broken. Seems like it was
never sufficiently tested probably because most of the time IOC was used
instead (i.e. no manual cache operations were done).
Now if we disable IOC in U-boot we'll get a lot of errors while using
DMA-enabled peripherals.
This time we fix it by substitution of broken per-line SLC operations
region operations as it is done in the Linux kernel (we took it from
v4.14 which is the latest stable as of today).
Among other things this implementation might be a bit faster because
instead of iteration over each and every cache line we're taking care
about entire region in one go.
Main changes:
* Replaced __slc_line_op (per line operations) by __slc_rgn_op
(region operations).
* Reworked __slc_entire_op to get rid of __after_slc_op and
__before_slc_op functions.
Note flush fix (flush only instead of flush-n-inv when OP_FLUSH is
used, see [1] for more details) is already incorporated here.
* Added SLC invalidation to invalidate_icache_all().
* Added (start >= end) check to invalidate_dcache_range() and
flush_dcache_range() as some buggy drivers pass region start == end.
* Added read-out of MMU BCR so we may know if PAE40 exists in HW and then
act on a particular AUX regs accordingly.
[1] http://lists.infradead.org/pipermail/linux-snps-arc/2018-January/003357.html
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Align the base address defined in header files with the base address used
in the DTS. This will facilitate the introduction of the DMA support.
Of all HSMMC users, only omap3 doesn't have the 0x100 reserved region at
the top. This region will be used to determine if the controller supports
DMA transfers
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This reverts commit 46831c1a4c.
This reserved area at the beginning of struct hsmm, will be used later to
support ADMA
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sata is equipped on ls1012a and can be a boot source. Add sata boot
support as an option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata is equipped on ls1046a and can be a boot source. Add sata boot
support as an option if available.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Both the "qixis_reset" and esbc_validate" commands can only be used in
full U-Boot so do not build them in SPL. As part of this rework the
qixis code to declare things as static and make use of __weak for
function aliases.
Cc; York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In some cases when "more" is told to page a given file it will prepend
the output with:
::::::::::::::
/PATH/TO/THE/FILE
::::::::::::::
And when this happens the output will not match the expected length.
Further, if we use a different pager we will instead fail the coverage
tests as we will not have 100% coverage. Update the help test to remove
the string in question.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The number 4 is dedicated on i.MX7ULP, but lpi2c will be reused on i.MX8,
4 is not valid. The seq number could be configured by alias node.
The following patch will use i2c4 as the begin for i.MX7ULP.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The system device-tree compiler may not be new enough to run the tests we
use in U-Boot (e.g. with binman). Allow use of a DTC environment variable
to point to the correct dtc. If not defined, the dtc on the default PATH
is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Remove the unit address from the config node name when U-Boot deals with
secure firmware FIT images.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Correct the generated unit names when U-Boot's mkimage creates a FIT
image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Adjust the FIT build script for 64-bit Allwinner boards to remove the
bogus addresses from the node names and avoid the warnings.
This avoids a warning with recent versions of the dtc tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in the tree where node names were mentioned in
comments, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in various documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address of a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in the FIT image example files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in the FIT image documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Binman has 100% test coverage for the code as it is at present. To
encourage it to stay that way, run the code-coverage test as part of the
normal U-Boot tests.
This is RFC because it requires the Python code coverage tools to be
available.
Signed-off-by: Simon Glass <sjg@chromium.org>
If lk lights up display and populates simple-framebuffer node, it will
also setup a reserved-memory node (needed by simplefb on linux). But
it isn't clever enough to cope when the reserved-memory node is not
present.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Similar to CONFIG_OF_BOARD, but in this case the fdt is still built by
u-boot build. This allows the board to patch the fdt, etc.
In the specific case of dragonboard 410c, we pass the u-boot generated
fdt to the previous stage of bootloader (by embedding it in the
u-boot.img that is loaded by lk/aboot), which patches the fdt and passes
it back to u-boot.
Signed-off-by: Rob Clark <robdclark@gmail.com>
[trini: Update board_fdt_blob_setup #if check]
Signed-off-by: Tom Rini <trini@konsulko.com>
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
In preparation to add support for the Dragonboard820c (APQ8096),
refactor the current Snapdragon clock driver.
No new functionality has been added.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
For example to store the environment in a file named "/uboot.env" in MMC
"0", where partition "1" contains the EXT4 filesystem, the following
configs should be added to the board's default config:
CONFIG_ENV_IS_IN_EXT4=y
CONFIG_ENV_EXT4_DEVICE_AND_PART="0:1"
CONFIG_ENV_EXT4_FILE="/uboot.env"
CONFIG_ENV_EXT4_INTERFACE="mmc"
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
[trini: Fix some line over 80 chars issues]
Signed-off-by: Tom Rini <trini@konsulko.com>
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.
QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
(brdcfg[0] >> 5) & 0x7
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot on ARM based platforms.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SP805-WDT module on LS1088A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.
Signed-off-by: Zhang Ying-22455 <ying.zhang22455@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Identify and distinguish between platform device type of MX7ULP
and LS1021A.
This is a fix to commit 7edf5c45("serial: lpuart: add i.MX7ULP
support").
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Align boards belonging to LS1012A, LS2080A SoC at one place.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This adds SH_ETHER to drivers/net/Kconfig and convert to Kconfig.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When we using network on board using sh-eth, it prints a lot of
"CACHE: Misaligned operation at range" messages.
This commit fixes this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This changes Change structure used in sh_eth_read and sh_eth_write function
from struct sh_eth_dev to struct sh_eth_info. This is necessary to convert
to Driver Model.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
bd_t is not used in sh_eth_config(). This deletes bd_t from sh_eth_config()
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This fixes the chord style checked by checkpatch.pl.
Details of change details are as follows:
- Fix typo
Change from alligned to aligned.
- Remove whitespace before ','
- Add spaces preferred around that '|'
- Fix missing a blank line after declarations
- Remove space after a cast declaration
- Fix format of block comments
- Add a blank line after function/struct/union/enum declarations
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This change allows the "MAY_FAIL" DHCP option to still attempt to
contact a DHCP server on each adapter and only give up once each
adapter has failed once. To get the existing behavior, set the
already-existing ethrotate=no variable.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Enable CONFIG_B53_SWITCH, define the CPU/management port number (8) and
enable all 5 ports of the switch to be usable.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a b53_reg read/write command which allows inspecting the switch
registers. Because the Broadcom BCM53xx registers have different sizes,
we need to split the accesses in 8, 16, 32, 48 or 64 bits to obtain
expected results.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Make sure that we pad small packets to a minimum length of 60 bytes
(without FCS). This is necessary to interface with Ethernet switches
that will reject RUNT frames unless padded correctly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a minimalistic Broadcom BCM53xx (roboswitch) switch driver similar
to the Marvell MV88E617x. This takes care of configuring the minimum
amount out of the switch hardware such that each user visible port
(configurable) and the CPU port can forward packets between each other
while preserving isolation with other ports.
This is useful for e.g: the Lamobo R1 board featuring a Broadcom
BCM53125 switch.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This implementation manages several clocks, disable and
free all of them in case of error during probe and in remove
callback.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch fixes a problem in the mvneta driver where if more than
one packet arrives between calls to mvneta_recv(), the additional
descriptors will be marked as free even though only one descriptor
has been read and processed from the receive queue. This causes
the additional packet(s) to be delayed until the next packet arrives.
>From this point on all packets will be delayed because the receive
queue will contain unprocessed packets but the hardware shows no
busy descriptors.
Signed-off-by: Jason Brown <jason.brown@apcon.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Since the return value is a signed int, if the leading MSB of rdreg is a 1,
it will get signed extended and will return a negative value which is an
error even though we read the correct value.
Fixes: dfcc496ed7 ("net: mii: Changes not made by spatch")
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
First, this table could never be included in the build anyway because
SH_ETH_TYPE_RZ is not defined until later in the file.
Second, the register PIR was missing, so PHY MDIO never worked.
Third, after adding the PIR register, the table is EXACTLY the same as
sh_eth_offset_gigabit, so there is no value to it.
Therefore, just delete it use the gigabit one.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The macros inl and outl maybe already be defined from file
arch/arm/include/asm/io.h so there may be no reason to define them.
And if you do try defined them here, you get a redefined complier warning.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This commit allows extended Marvell registers to be read with:
foo > mdio rx FEC 3.10
Reading from bus FEC
PHY at address 0:
3.16 - 0x1063
foo > mdio wx FEC 3.10 0x1011
The above code changes the way ETH connector LEDs blink.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Although Xilinx Zynq SoC was using MACB similar hardware. However,
U-boot MACB driver was not supporting Xilinx Zynq SoC. This patch is
to add support for the Xilinx Zynq SoC to the existing MACB network
driver.
This patch is to add Zynq GEM DMA Config, provide callback
function for different linkspeed for case of using Xilinx Zynq
Programmable Logic as GMII to RGMII converter.
This patch convert the return value to use error codes.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The hab_rvt_failsafe() callback according to the HABv4 documentation:
"This function provides a safe path when image authentication has failed
and all possible boot paths have been exhausted. It is intended for use by
post-ROM boot stage components, via the ROM Vector Table."
Once invoked the part will drop down to its BootROM USB recovery mode.
Should it be the case that the part is in secure boot mode - only an
appropriately signed binary will be accepted by the ROM and subsequently
executed.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The BootROM will not successfully process a HAB image passed by u-boot
unless the board has been set into locked mode. Some of the existing usages
of authenticate_image() expect and rely on unlocked boards doing the
following
1. Not calling into the BootROM authenticate_image() callback
2. Returning a pass status for authenticate_image() calls anyway
A previous patch removed the necessity to call into imx_hab_is_enabled()
twice. This patch ensures the reliance on authenticate_image() returning
zero is maintained.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Suggested-by: Breno Matheus Lima <brenomatheus@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
The hab_rvt_check_target() callback according to the HABv4 documentation:
"This function reports whether or not a given target region is allowed for
either peripheral configuration or image loading in memory. It is intended
for use by post-ROM boot stage components, via the ROM Vector Table, in
order to avoid configuring security-sensitive peripherals, or loading
images over sensitive memory regions or outside recognized memory devices
in the address map."
It is a useful function to support as a precursor to calling into
authenticate_image() to validate the target memory region is good.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The various i.MX BootROMs containing the High Assurance Boot (HAB) block
rely on a data structure called the Image Vector Table (IVT) to describe to
the BootROM where to locate various data-structures used by HAB during
authentication.
This patch adds a definition of the IVT header for use in later patches,
where we will break the current incorrect dependence on fixed offsets in
favour of an IVT described parsing of incoming binaries.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
u-boot command "hab_auth_img" tells a user that it takes
- addr - image hex address
- offset - hex offset of IVT in the image
but in fact the callback hab_auth_img makes to authenticate_image treats
the second 'offset' parameter as an image length.
Furthermore existing code requires the IVT header to be appended to the end
of the image which is not actually a requirement of HABv4.
This patch fixes this situation by
1: Adding a new parameter to hab_auth_img
- addr : image hex address
- length : total length of the image
- offset : offset of IVT from addr
2: Updates the existing call into authenticate_image() in
arch/arm/mach-imx/spl.c:jump_to_image_no_args() to pass
addr, length and IVT offset respectively.
This allows then hab_auth_img to actually operate the way it was specified
in the help text and should still allow existing code to work.
It has the added advantage that the IVT header doesn't have to be appended
to an image given to HAB - it can be prepended for example.
Note prepending the IVT is what u-boot will do when making an IVT for the
BootROM. It should be possible for u-boot properly authenticate images
made by mkimage via HAB.
This patch is the first step in making that happen subsequent patches will
focus on removing hard-coded offsets to the IVT, which again is not
mandated to live at the end of a .imx image.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
authenticate_image returns 1 for success and 0 for failure. That result
code is mapped directly to the result code for the command line function
hab_auth_img - which means when hab_auth_img succeeds it is returning
CMD_RET_FAILURE (1) instead of CMD_RET_SUCCESS (0).
This patch fixes this behaviour by making authenticate_image() return 0 for
success and 1 for failure. Both users of authenticate_image() as a result
have some minimal churn. The upshot is once done when hab_auth_img is
called from the command line we set $? in the standard way for scripting
functions to act on.
Fixes: 36c1ca4d46 ("imx: Support i.MX6 High Assurance Boot
authentication")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Both usages of authenticate_image treat the result code as a simple binary.
The command line usage of authenticate_image directly returns the result
code of authenticate_image as a success/failure code.
Right now when calling hab_auth_img and test the result code in a shell a
passing hab_auth_img will appear to the shell as a fail.
The first step in fixing this behaviour is to fix-up the result code return
by authenticate_image() itself, subsequent patches fix the interpretation
of authenticate_image so that zero will return CMD_RET_SUCCESS and non-zero
will return CMD_RET_FAILURE.
The first step is fixing the return type in authenticate_image() so do that
now.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Sven Ebenfeld <sven.ebenfeld@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Breno Matheus Lima <brenomatheus@gmail.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
With CONFIG_SYS_INIT_SP_BSS_OFFSET enabled, the initial (pre-relocation)
stack is placed some distance after bss_start. The control DTB is appended
to the U-Boot binary at bss_start. If the DTB is too large, or the SP BSS
offset too small, then the initial stack could corrupt the DTB. Enhance
the Makefile to check whether this is likely to occur.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Request that all environment variables containing hard-coded address be
calculated at boot time instead.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In the presence of potentially fragemented memory, we cannot hard-code
addresses into environment variables such as kernel_addr_r. Instead, we
must calculate those addresses at run-time based on available memory
locations. Implement the code to perform such runtime calculation, based
on requirements described in environment variables, to allow the user
full control over the allocation.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra186 currently restricts its DRAM usage to entries in the /memory node
in the DTB passed to it. However, the MMU configuration always maps the
entire first 2GB of RAM. This could allow the CPU to speculatively access
RAM that isn't part of the in-use banks. This patch switches to runtime
construction of the table that's used to construct the MMU translation
tables, and thus prevents access to RAM that's not part of a valid bank.
Note: This patch is intended to prevent access to RAM regions which U-Boot
does not need to access, with the primary purpose of avoiding theoretical
speculative access to physical regions for which the HW will throw errors
(e.g. carve-outs that the CPU has no permission to access at a bus level,
bad ECC pages, etc.). In particular, this patch is not deliberately
related to the speculation-related security issues that were recently
announced. The apparent similarity is a coincidence.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On this platform, there may be up to 1024 unusable chunks of memory.
Increase CONFIG_NR_DRAM_BANKS so that U-Boot can remember all the banks
required to represent such fragmented memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In the future, the list of DRAM regions passed to U-Boot in the DTB may
be quite long and fragmented. Due to this, U-Boot must search through the
regions to find the best region to relocate into, rather than relying on
the current assumption that the top of bank 0 is a reasonable relocation
target. This change implements such searching.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
arch_lmb_reserve() currently assumes that the stack pointer is within DRAM
bank 0. This is not necessarily true. Enhance the code to search through
DRAM banks until the bank that does contain SP is found, and then reserve
the tail of that bank.
Fixes: 2d1916e48b ("ARM: add flat device tree support")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Apply a few small fixes for the DTB /memory node parsing from NVIDIA's
downstream U-Boot:
- Allow arbitrary number of DRAM banks.
- Correctly calculate the number of DRAM banks.
- Clip PCIe memory in the same way as U-Boot CPU memory use.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable CONFIG_LINUX_KERNEL_IMAGE_HEADER for all 64-bit Tegra boards.
cboot (the boot SW that runs before U-Boot) will eventually use this
information.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Allow placing a Linux kernel image header at the start of the U-Boot
binary. This is useful since the image header reports the amount of memory
(BSS and similar) that U-Boot needs to use, but that isn't part of the
binary size. This can be used by the code that loads U-Boot into memory to
determine where to load U-Boot, based on other users of memory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable CONFIG_SYS_INIT_SP_BSS_OFFSET for all 64-bit Tegra boards. Place
the stack/... 512KiB from the end of the U-Boot binary. This should be
plenty to accommodate the current DTBs (max 64 KiB), early malloc region
(6KiB), stack usage, and plenty of slack, while still not placing it too
far away from the U-Boot binary.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-Boot typically uses a hard-coded value for the stack pointer before
relocation. Implement option SYS_INIT_SP_BSS_OFFSET to instead calculate
the initial SP at run-time. This is useful to avoid hard-coding addresses
into U-Boot, so that can be loaded and executed at arbitrary addresses and
thus avoid using arbitrary addresses at runtime. This option's value is
the offset added to &_bss_start in order to calculate the stack pointer.
This offset should be large enough so that the early malloc region, global
data (gd), and early stack usage do not overlap any appended DTB.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
No 64-bit Tegra uses SPL. Remove various unused definitions from config
headers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
64-bit Tegra don't use SPL, and soon won't define CONFIG_SPL_TEXT_BASE
when building. Fix the binman .dts file so that it doesn't use undefined
values.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Current USDHC driver will reset VSELECT to 0 (3.3v) during mmc init,
then set to 1 for 1.8v eMMC I/O. When booting from eMMC, since ROM has
already set VSELECT to 1.8v before running the u-boot. This reset in
USDHC driver causes a short 2.2v pulse on CMD pin.
Fix this issue by not reset VSELECT to 0 when 1.8v flag is set.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
In order to discard this code when unused in SPL we need to guard the
command with a check for CONFIG_SPL_BUILD and we rearrange the code
slightly to make this cleaner.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Some distributions like Fedora expect U-Boot to select a proper
devicetree. Since there are several variants of the cm-fx6 module
featuring different SoC variants and the module can be paired with
several baseboards, it is not viable to hardcode a filename.
Instead, follow the lead of other i.MX6 based devices and try to
determine the devicetree to use with the help of the board name
and the SoC variant exported by the board code, before calling the
distro bootcommand.
For now, only for the Utilite Pro a proper devicetree filename is
known but further variants of the Utilite Computer or other devices
based on the cm-fx6 module may be added in the future.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.
At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.
Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.
For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
By default, the subordinate is set equally to the secondary bus (1) when
the RC boots, and does not alter afterwards.
This means that theoretically, the highest bus reachable downstream is
bus 1.
Force the PCIe RC subordinate to 0xff, otherwise no downstream
devices will be detected behind bus 1 if the booting OS does not allow
enumerating a higher busnr than the subordinate value of the primary
bus.
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration()
show the same error message, which is confusing for debugging.
Disambiguate the mmdc_do_dqs_calibration() error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same config option as wandboard.
mx6sabreauto board uses the following pins for console:
PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA
So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.
The config option for sabreauto can be added later when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The "clocks" and "bootaux" commands are only usable in full U-Boot, not
SPL, so do not link them inside of SPL. Rework a little of the bootaux
related code to make use of __weak and declare parts of it static as
it's local to the file.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
To support QSPI DM driver
- Add spi0 alias for qspi node. Which is used for bus number 0.
- Modify the n25q256a@0 compatible property to "spi-flash".
- Modify spi4 (gpio_spi) node to spi5
- Define DM SPI/QSPI related config to enable QSPI
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QSPI module on i.MX7D is modified from i.MX6SX. The module used on
i.MX6UL/6ULL is reused from i.MX7D. They share same tx buffer size.
The endianness is not set at qspi driver initialization. So if we don't
boot from QSPI, we will get wrong endianness when accessing from AHB
address directly.
Add the compatible entry for 6ul/7d.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX6ULL also does not have a MMDC_P1_BASE_ADDR, so do not try to
access it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <ssbabic@denx.de>
The u-boot-dtb.imx size is about 519KB, so 8 * 64KB conflicts
with u-boot-dtb.imx. Enlarge the offset to 14 * 64KB to fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Because kernel set WDOG_B mux before pad with the common pinctrl
framwork now and wdog reset will be triggered once set WDOG_B mux
with default pad setting, we set pad setting here to workaround this.
Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
as GPIO mux firstly here to workaround it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
On i.MX7ULP, the fuse words (except bank 0 and 1) only supports to
write once, because they use ECC mode. Multiple writes may damage
the ECC value and cause a wrong fuse value decoded when reading.
This patch adds a checking before the fuse word programming, only
can write when the word value is 0.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add documents to describe NX25 and AE250.
Also update other documents for RISC-V.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Add prelink-riscv to arrange .rela.dyn and .rela.got
in compile time. So that u-boot can be directly
executed without fixup.
Signed-off-by: Chih-Mao Chen <cmchen@andestech.com>
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Add header files for RISC-V.
Cache, ptregs, data type and other definitions are included.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
AE250 is the Soc using NX25 cpu core base on RISC-V arch.
Details please see the doc/README.ae250.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Add Andes nx25 cpu core (called AndesStar V5) to support RISC-V arch
Verifications:
1. startup and relocation ok.
2. boot from rom or ram both ok.
2. timer driver ok.
3. uart driver ok
4. mmc driver ok
5. spi driver ok.
6. 32/64 bit both ok.
Detail verification message please see doc/README.ae250.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
Cc: Padmarao Begari <Padmarao.Begari@microsemi.com>
hc_wp_grp_size is needed only if hardware partitionning is used.
On ARM removing it saves about 30 bytes of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This information is only used by the "mmc info" command.
On ARM removing this information from SPL saves about 140 of code space.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Also remove erase_grp_size and write_bl_len from struct mmc as they are
not used anymore. On ARM, removing them saves about 100 bytes of code
space in SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The content of ssr is useful only for erase operations.
on ARM, removing sd_read_ssr() saves around 300 bytes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows using CONFIG_IS_ENABLED(MMC_WRITE) to compile out code
needed only if write support is required.
The option is added for u-boot and for SPL
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
struct mmc_data contains the block size to use for the data transfer.
Use this information instead of using the default value or the block length
information stored in struct mmc.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The am335x_hs_evm runs into size constraint problems at times with
various toolchains as changes come in due to the config have a large
number of options in SPL (to showcase what is possible) while also
having rather constrained binary limits. Gain some of this room back by
lowering the loglevel, disabling HW partition support and switching over
to the tiny FIT image support.
Cc: Andrew F. Davis <afd@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
---
I'd really appreciate a run-time test of this patch if at all possible
as I'm a little worried about TINY_FIT being incompatible with all of
the security options. Thanks!
The SDcard initialization procedure does a few more things than it did earlier:
* switch the bus width even for 1-bit bus width
* check that speed has been properly set (in resp[4] of SD_CMD_SWITCH_FUNC)
Update the SD simulator to handle those requests gracefully.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The changes in the MMC stack have increased its footprint up to the point
were its breaks the generation of the SPL for this platform.
Fix this by reducing the loglevel.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Peter Howard <phoward@gme.net.au>
builds are broken because the size of the binary exceeds the limit.
Make some space by removing support for hardware partitioning as those
boards don't have any eMMC.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Not all boards have an eMMC and not all users have a need for this.
Allow to compile it out. By default it is still included.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Supporting USH and HS200 increases the code size as it brings in IO voltage
control, tuning and fatter data structures.
Use Kconfig configuration to select which of those features should be
built in.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This allows to compile out the log message by tweaking the LOGLEVEL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Not using this function reduces the size of the binary. It's replaces by
a standard malloc() and the alignment requirement is handled by an
intermediate buffer on the stack.
Also make sure that the allocated buffer is freed in case of error.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The ext_csd is allocated only for MMC above version 4. The compare will
crash or fail for older MMCs.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Make sure that those basic capabilities are advertised by the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the legacy modes were not added to the list of supported modes, old
cards that do not support other modes could not be used.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
* convert to livetree API
* don't fail because of an invalid bus-width, instead default to 1-bit.
* recognize 1.2v DDR and 1.2v HS200 flags
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is a useful information while debugging the initialization process or
performance issues.
Also dump this information with the other mmc info if the verbose option
is selected
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function to parse host controller dt node and
set mmc_config. This function can be used by mmc controller
drivers to set the generic mmc_config.
This function can be extended to set other UHS mode caps
once UHS mode support is added.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200/SDR104 requires tuning command to be sent to the card.
Add a simple function to send tuning command and to read and
compare the received data with the tuning block pattern.
This function can be used by platform driver to perform DLL
tuning.
This patch is similar to
commit 996903de92f0 ("mmc: core: add core-level function for
sending tuning commands") added in linux kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
HS200 only supports 1.2v and 1.8v signal voltages. DDR52 supports 3.3v/1.8v
or 1.2v signal voltages.
Select the lowest voltage available when using those modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
With certain SD cards like Kingston 8GB/16GB UHS card, it is seen that
MMC_CMD_ALL_SEND_CID cmd fails on first attempt, but succeeds
subsequently. Therefore, retry MMC_CMD_ALL_SEND_CID cmd a few time
as done in Linux kernel.
Similarly, it is seen that MMC_CMD_SET_BLOCKLEN may fail on first
attempt, therefore retry this cmd a few times as done in kernel.
To make it clear that those are optionnal workarounds, a new Kconfig
option 'MMC_QUIRKS' is added (enabled by default).
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Boot partitions do not support HS200. Changing to a lower performance mode
is required to access them.
mmc_select_mode_and_width() and sd_select_mode_and_width() are modified to
make it easier to call them outside of the initialization context.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a power cycle cannot be done on Vcc, it is safer not to try the UHS
modes because we wouldn't be able to recover from an error occurring
during the UHS initialization.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add UHS modes to the list of supported modes, get the UHS capabilites of
the SDcard and implement the procedure to switch the voltage (UHS modes
use 1v8 IO lines)
During the voltage switch procedure, DAT0 is used by the card to signal
when it's ready. The optional card_busy() callback can be used to get this
information from the host driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add HS200 to the list of supported modes and introduce tuning in the MMC
startup process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tuning is a mandatory step in the initialization of SDR104 and HS200 modes.
This callback execute the tuning process.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
There is no point in having the mmc clock enabled during
power off. Disable the mmc clock. This is similar to how it's
programmed in Linux Kernel.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc clock has to be disabled in certain cases like during
the voltage switch sequence. Modify mmc_set_clock function
to take disable as an argument that signifies if the
clock has to be enabled or disabled.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc/sd specification requires vdd to be disabled for 1 ms
and then enabled again during power cycle. Add a
function in mmc core to perform power cycle and set
the io signal to it's initial state.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new callback function *send_init_stream* which start a sequence of
at least 74 clock cycles.
The mmc core uses *mmc_send_init_stream* in order to invoke the callback
function. This will be used during power cycle where the specification
requires such a sequence after power up.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add a new function *mmc_set_signal_voltage* in mmc core
which can be used during mmc initialization to select the
signal voltage. Platform driver should use the set_ios
callback function to select the signal voltage.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
set_ios callback has a return value of 'int' but the mmc_set_ios()
function ignore this. Modify mmc_set_ios() and the callers of mmc_set_ios() to
to return the error status.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The MMC startup process currently handles 4 modes. To make it easier to
add support for more modes, let's make the process more generic and use a
list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SDcard startup process currently handles only 2 modes. To make it
easier to add support for more modes, let's make the process more generic
and use a list of the modes to try.
The major functional change is that when a mode fails we try the next one.
Not all modes are tried, only those supported by the card and the host.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Display the mode name when the user execute 'mmc info'. Also instead of
displaying tran_speed, display the actual bus speed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a simple helper function to display information (bus width and
mode) based on a capability mask. Useful for debug.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
no functionnal changes.
In order to add the support for the high speed SD and MMC modes, it is
useful to track this information.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This will be reused later in the selection of high speed and ddr modes.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ext csd is used for comparison many times. Keep a reference content
of the ext csd in the struct mmc to avoid reading multiple times
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
no functionnal change. This is only to further reduce the size o
mmc_startup().
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
No functionnal change here. The function is really big and can be split.
The part related to bus configuration are put in 2 separate functions: one
for MMC and one for SD.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Get a reference to the regulator devices from the dts and store them
in the struct mmc for later use.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
data is defined as struct mmc_data *data.
So it should not be compared to 0.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes emmc initialization regression on the db410c platform.
Clearing this register while SDHCI_PRESENT_STATE reports
SDHCI_CMD_INHIBIT leads to undefined behaviour on the db410c.
When commit 7dde50 was merged (mmc: sdhci: Wait for SDHCI_INT_DATA_END
when transferring), SDHCI transfers transitioned to wait for bit
SDHCI_INT_DATA_END before flagging transfers done.
Without this patch, the db410 platform fails to initialize its eMMC
due to all of its transfers timing out (SDHCI_INT_DATA_END is never
raised after all the blocks have been transferred).
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This patch fixes some warnings when building boards that do not define
DM_I2C_COMPAT i.e. boards that entirely rely on the new i2c layer.
Signed-off-by: Felix Brack <fb@ltec.ch>
priv pointer should be freed before returning with an error value
from exynos_dwmci_get_config().
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Raghu Bharadwaj <raghu@techveda.org>
__be32_to_cpu() accepts argument of type __be32. This patch changes
type of the buffer in ALLOC_CACHE_ALIGN_BUFFER macro to __be32, which
is then passed to __be32_to_cpu().
This prevents sparse build warnings.
drivers/mmc/mmc.c: warning: cast to restricted __be32
Signed-off-by: Suniel Mahesh <sunil.m@techveda.org>
Signed-off-by: Karthik Tummala <karthik@techveda.org>
The clock selection is done now from the am335x-fb code, so there is no
more need doing this in the board code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Actual am335x-fb implementation takes now a real clock frequency instead
a divider. So this component doesn't need to know anymore some base
frequency of the LCDC, we simply provide the pixel-clock frequency.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The LCDC IP-core an be feed from several clock sources, one of those is
a dedicated DPLL for generating a dividable base-clock for this IP-core.
The TRM specifies the maximum input frequency for the LCCD with 200 MHz,
so we must not exceed this value with the PLL frequency (which can lock
much higher).
This patch tries every combination of multipliers and divisors of the
PLL and the IP-core itself for getting as near as possible the the
requested panel->pxl_clk.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Compile-off mp.c and libfdt.c in case of SPL build. SPL size reduces
by approx 2k.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove duplicate macro CONFIG_FSL_PCIE_RESET and update its comment.
It enables PCIe reset to fix link width 2x - 4x.
Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
855873: An eviction might overtake a cache clean operation
Workaround: The erratum can be avoided by upgrading cache clean by
address operations to cache clean and invalidate operations. For
Cortex-A53 r0p3 and later release, this can be achieved by setting
CPUACTLR.ENDCCASCI to 1.
This patch is to implement the workaround for this erratum.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The CONFIG_SYS_DPAA_QBMAN define is used by DPAA1 freescale SOCs to
add device tree fixups that allow deep sleep in Linux. The define was
placed in header files included by a number of boards, but was not
explicitly documented in any of the Kconfigs. A description was added
to the drivers/networking menuconfig and default selection for
current SOCs that have this part
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Sata registers PP2C and PP3C are used to control the configuration
of the PHY control OOB timing for the COMINIT/COMWAKE parameters
respectively. Calculate those parameters from port clock frequency.
Overwrite those registers with calculated values to get better OOB
timing.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Given gcc-6.1 and later we can now safely have strings discarded when
the functions are unused. This lets us drop certain cases of not
building something so that we don't have the strings brought in when the
code was discarded. Simplify the code now by dropping guards we don't
need now.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
Cc: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
commit 21a24c3bf3 ("fs/fat: fix case for FAT shortnames") made it
possible that get_name() returns file names with some upper cases.
find_directory_entry() must be updated to take this account, and use
case-insensitive functions to compare file names.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AP325RXA
CONFIG_AP_SH4A_4A
CONFIG_CPU_SH_TYPE_R
CONFIG_ECOVEC
CONFIG_ESPT
CONFIG_MIGO_R
CONFIG_MPR2
CONFIG_MS7720SE
CONFIG_MS7722SE
CONFIG_MS7750SE
CONFIG_R0P7734
CONFIG_R2DPLUS
CONFIG_RSK7203
CONFIG_RSK7264
CONFIG_RSK7269
CONFIG_SH7752EVB
CONFIG_SH7753EVB
CONFIG_SH7757LCR
CONFIG_SH7763RDP
CONFIG_SH7785LCR
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
These macros are all defined once and never checked or used anywhere:
CONFIG_MACH_ASPENITE
CONFIG_MACH_DAVINCI_CALIMAIN
CONFIG_MACH_DOCKSTAR
CONFIG_MACH_EDMINIV2
CONFIG_MACH_GOFLEXHOME
CONFIG_MACH_GONI
CONFIG_MACH_GURUPLUG
CONFIG_MACH_KM_KIRKWOOD
CONFIG_MACH_OPENRD_BASE
CONFIG_MACH_SHEEVAPLUG
Almost all of them were only used for the mach_is_foo() logic in
arch/arm/asm/mach-types.h that were dropped in
commit f9dadaef8b ("arm: Re-sync asm/mach-types.h with
Linux Kernel v4.9")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Configure AM57xx EVMs for the exact PHY part that is
present on the various boards. This makes U-Boot apply
configurations needed for this PHY like centering the
FLP timing.
For configurations to take effect, DM_ETH needs to be
enabled. Do that too.
Tested on BeagleBoard x15 and AM571x IDK.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The 't208xrdb t4qds t102*' job is close to the time limit and
sometimes fails, so this splits it into 3 separate jobs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Last user of this option went away in 2015 in commit:
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
BCM2835 ARM Peripherals doc shows gpio pins 4, 5, 6, 12 and 13 carry altenate
function, ALT5 for ARM JTAG
Signed-off-by: Henry Zhang <henryzhang62@yahoo.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add DT nodes to enable ARM_PL180_MMCI IP support for STM32F746
and STM32F769 discovery boards
There is a hardware issue on these boards, it misses a pullup on the GPIO line
used as card detect to allow correct SD card detection.
As workaround, cd-gpios property is not present in DT.
So SD card is always considered present in the slot.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board offers :
_ STM32F469NIH6 microcontroller featuring 2 Mbytes of Flash memory
and 324 Kbytes of RAM in BGA216 package
_ On-board ST-LINK/V2-1 SWD debugger, supporting USB reenumeration capability:
_ Mbed-enabled (mbed.org)
_ USB functions: USB virtual COM port, mass storage, debug port
_ 4 inches 800x480 pixel TFT color LCD with MIPI DSI interface and capacitive
touch screen
_ SAI Audio DAC, with a stereo headphone output jack
_ 3 MEMS microphones
_ MicroSD card connector
_ I2C extension connector
_ 4Mx32bit SDRAM
_ 128-Mbit Quad-SPI NOR Flash
_ Reset and wake-up buttons
_ 4 color user LEDs
_ USB OTG FS with Micro-AB connector
_ Three power supply options:
_ Expansion connectors and Arduino™ UNO V3 connectors
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This DT file comes from kernel v4.15-rc1
stm32f469-pinctrl.dtsi header has been updated with correct
STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to controls the memory internal mapping at
address 0x0000 0000.
We can either map at 0x0000 0000 :
_ main flash memory
_ system flash memory
_ FMC bank1 (NOR/PSRAM 1 and 2)
_ embedded SRAM
_ FMC/SDRAM bank1
This is needed for future STM32F469-disco board
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32f7_gpio.c and pinctrl_stm32.c drivers
instead of board GPIO initialization.
Remove stm32_gpio.c which is no more used and migrate
structs stm32_gpio_regs and stm32_gpio_priv into
arch-stm32f4/gpio.h to not break compilation.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM clk_stm32f.c driver instead of dedicated
mach-stm32/stm32f4/clock.c.
Migrate periph_clock defines from stm32_periph.h directly in
CLK driver. These periph_clock defines will be removed when STMMAC,
TIMER2 and SYSCFG drivers will support DM CLK.
Enable also CLK flag.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to use common clock driver between STM32F4 and
STM32F7, remove clock_get() call
As APB_PSC is always set to 2, only case when
clock_get(CLOCK_AHB) != clock_get(CLOCK_APB1) is kept
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Remove serial_stm32.c driver and uart init from board file,
use available DM serial_stm32x7.c driver compatible for
STM32F4/F7 and H7 SoCs.
The serial_stm32x7.c driver will be renamed later with a more
generic name as it's shared with all STM32 Socs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This allows to support rcc MFD driver.
By enabling all these flags, we need to increase malloc area to avoid
crash during early stage.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
STM32F4 SoCs uses the same pinctrl block as found into
STM32F7 and H7 SoCs.
We can add "st,stm32f429-pinctrl" and "st,stm32f469-pinctrl"
compatible string into pinctrl_stm32.c.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_sdram.c driver instead of board
SDRAM initialization.
For that, enable OF_CONTROL, OF_EMBED and STM32_SDRAM flags.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
_ Add gpio compatible and aliases for stm32f429
_ Add FMC sdram node with associated new bindings value to
manage second bank (ie bank 1).
_ Add "u-boot,dm-pre-reloc" for rcc, fmc, fixed-clock, pinctrl,
pwrcfg and gpio nodes.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
All these files comes from kernel v4.15-rc1.
Update some header with correct STMicroelectronics Copyright.
Remove the paragraph about writing to the Free Software
Foundation's mailing address as requested by checkpatch.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The DB-88F6820-AMC connects ethernet@34000 and ethernet@70000 which are
labeled as eth2 and eth0 in armada-38x.dts. The ethernet@30000 (eth1) is
not used on the AMC board.
This eliminates the following bootup message
Device 'ethernet@70000': seq 0 is in use by 'ethernet@34000'
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
add a simple readme to introduce rockusb and tell people how to use it
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
this patch add rockusb command. the usage is
rockusb <USB_controller> <devtype> <dev[:part]>
e.g. rockusb 0 mmc 0
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
this patch implement rockusb protocol on the device side. this is based on
USB download gadget infrastructure. the rockusb function implements the rd,
wl, rid commands. it can work with rkdeveloptool
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now that the musb sunxi glue driver is completely device model / device
tree driven, we should use the base address from the device tree,
instead of hard-coding it in the source code.
Fixes: 3a61b080ac ("musb: sunxi: switch to the device model")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Linux bindings have been introduced in the code (removing the U-Boot
specific ones) without documentation update. Compatible string has
changed, as well as the four GPIO properties. Reflect this by updating
the soft-spi.txt documentation.
Fixes: 102412c415 ("dm: spi: soft_spi: switch to use linux compatible string")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Commit 8620f38409 ("dm: sunxi: Linksprite_pcDuino3: Correct polarity
of MMC card detect") claims that the Pcduino3 device tree had an
incorrect polarity for the card detect pin and thus changed the polarity
flag of the cd-gpios from GPIO_ACTIVE_HIGH to GPIO_ACTIVE_LOW.
Actually the DT was correct since according to the mmc binding, a
combination of GPIO_ACTIVE_HIGH + cd-inverted results in an active-low
polarity. But because the U-Boot driver lacks the code to look at the
cd-inverted property (unlike the Linux driver) it interpreted the
polarity of active-high. Thus, after that commit the DT is actually
wrong from the binding/Linux point of view.
To make both Linux and U-Boot interpret the DT in the same way, just
drop the left-over cd-inverted property. I've sent a Linux patch to
switch all sunxi DTs over to not using the cd-inverted property, so
eventually all sunxi boards in U-Boot will be consistent in not using
cd-inverted.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Libre Computer Board ALL-H3-CC from Libre Technology is a Raspberry
Pi B+ form factor single board computer based on the Allwinner H3 SoC.
The board has 1GB DDR3 SDRAM, provided by 4 2Gb chips. The mounting holes
and connectors are in the exact same position as on the Raspberry Pi B+.
Raspberry Pi B+ like peripherals supported on this board include:
- Power input through micro-USB connector (without USB OTG)
- Native 100 Mbps ethernet using the internal PHY, as opposed to
USB-based on the RPi
- 4x USB 2.0 host ports, directly connected to the SoC, as opposed to
being connected through a USB 2.0 hub on the RPi
- TV and audio output on a 3.5mm TRRS jack
- HDMI output
- Micro-SD card slot
- Standard RPi B+ GPIO header, with the standard peripherals routed to
the same pins.
* 5V, 3.3V power, and ground
* I2C0 on the H3 is routed to I2C1 pins on the RPi header
* I2C1 on the H3 is routed to I2C0 pins on the RPi header
* UART1 on the H3 is routed to UART0 pins on the RPi header
* SPI0 on the H3 is routed to SPI0 pins on the RPi header,
with GPIO pin PA17 replacing the missing Chip Select 1
* I2S1 on the H3 is routed to PCM pins on the RPi header
- Additional peripherals from the H3 are available on different pins.
These include I2S0, JTAG, PWM1, SPDIF, SPI1, and UART3
In addition, there are a number of new features:
- Console UART header
- Consumer IR receiver
- Camera interface (not compatible with RPi)
- Onboard microphone
- eMMC expansion module port
- Heatsink mounting holes
This patch adds defconfig and dts files for this board. The dts file is
the same as the one submitted for inclusion in Linux, with some minor
revisions to match the dtsi file and old EMAC bindings in U-boot.
Since the OTG controller is wired to a USB host port, and the H3 has
proper USB hosts to handle host mode, the MUSB driver is not enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
By applying this patch, we are ensuring that the code paths
responsible for applying errata workarounds are also exercised
on CPU revisions, which actually don't need these workarounds.
Only CONFIG_ARM_ERRATA_621766, CONFIG_ARM_ERRATA_454179,
CONFIG_ARM_ERRATA_725233 and CONFIG_ARM_ERRATA_430973 are
covered by this patch (Cortex-A8).
This improves code coverage when testing U-Boot builds
on newer hardware. In particular, the problematic commit
00bbe96eba ("arm: omap: Unify get_device_type() function")
would break both BeageBoard and BeagleBoard XM rather than
just older BeagleBoard.
As an additional bonus, we need fewer instructins and the SPL
size is reduced.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Armada pinctrl drivers shall not be compiled without the entire pinctrl
framework and thus lack a "depends on" condition, otherwise the driver
will simply not be probed.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Until now, Armada 3700 SoCs could not enable the mvneta driver, and thus
did not benefit from Ethernet support. Add ARMADA_3700 in the
"depends on" list of the MVNETA Kconfig entry.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
the values of dt_addr_r/kernel_addr_r/ramdisk_addr_r are taken from
the downstream 'u-boot-2017.03-armada-17.10' release.
the chosen values of scriptaddr and pxefile_addr_r are below fdt_addr_r,
in 1MB steps.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Introduce the recovery image download script for usage with
Marvell Armada SoC families (excepting 37xx family).
Since Marvell BootROM uses a sliding window in UART buffer
for detecting escape sequence during the boot, it's easier
to interrupt the normal boot flow by sending a long stream
of chained escape sequences to the serial port instead of
periodically sending a single escape sequence as it is done
by kwboot utility.
Additional benefit of using this script is the ability to
adjust the escape sequence stream length withoiut need for
compilation.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Igal Liberman <igall@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
I do not see a good reason to do this by a CONFIG option that affects
all SoCs. The ram_size can be adjusted by dram_init() at run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I did not enable SDMA when I added sdhci-cadence support because LD20
boards are equipped with a large amount memory beyond 32 bit address
range, but SDMA does not support the 64bit address. U-Boot relocates
itself to the end of effectively available RAM. This would make the
MMC enumeration fail because the buffer for EXT_CSD allocated in the
stack would go too high, then SDMA would fail to transfer data.
Recent SDHCI-compatible controllers support ADMA, but unfortunately
U-Boot does not support ADMA.
In the previous commit, I hided the DRAM area that exceeds the 32 bit
address range. Now, I can enable CONFIG_MMC_SDHCI_SDMA.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
LD20 / PXs3 boards are equipped with a large amount of memory beyond
the 32 bit address range. U-Boot relocates itself to the end of the
available RAM.
This is a problem for DMA engines that only support 32 bit physical
address, like the SDMA of SDHCI controllers.
In fact, U-Boot does not need to run at the very end of RAM. It is
rather troublesome for drivers with DMA engines because U-Boot does
not have API like dma_set_mask(), so DMA silently fails, making the
driver debugging difficult.
Hide the memory region that exceeds the 32 bit address range. It can
be done by simply carving out gd->ram_size. It would also possible to
override get_effective_memsize() or to define CONFIG_MAX_MEM_MAPPED,
but dram_init() is a good enough place to do this job.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order for these commands to not be included in SPL we need to guard
compilation with CONFIG_SPL_BUILD checks. Reorganize some sections of
code slightly in order to avoid new warnings and mark the command
functions as static as they should have been before.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_CMD_PART item, as default environment requires it
and complains this command in unknown.
Signed-off-by: Andrey Zhizhikin <andrey.z@gmail.com>
When enable CONFIG_HAS_FSL_DR_USB, we might encounter below compile
warning, apply this patch can fix it:
drivers/usb/host/ehci-fsl.c:109:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
((u32)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
^
drivers/usb/host/ehci-fsl.c:108:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
hcor = (struct ehci_hcor *)
^
drivers/usb/host/ehci-fsl.c:115:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
drivers/usb/host/ehci-fsl.c:115:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Without this propertiy, U-Boot will pop warning of 'USB phy type not
defined' when select CONFIG_HAS_FSL_DR_USB.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
It is not much needed to print nand size in SPL during nand boot,
and most of nand spl drivers doesn't print the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
board/icorem6_rqs/ is forgot to remove while moving
common board files together in
(sha1: 52aaddd6f4)
"i..MX6: engicam: Add imx6q/imx6ul boards for existing boards"
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The i.MX 6UL/ULL feature a Cortex-A7 CPU which suppor the ARM
generic timer. This change makes use of the ARM generic timer in
U-Boot.
This is crucial to make the ARM generic timers usable in Linux since
timer_init() initalizes the system counter module, which is necessary
to use the generic timers CP15 registers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Introduce a new config symbol to select the i.MX
General Purpose Timer (GPT).
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The blob_encap and blob_decap functions were not flushing the dcache
before passing data to CAAM/DMA and not invalidating the dcache when
getting data back.
Therefore, blob encapsulation and decapsulation failed with errors like
the following due to data cache incoherency:
"40000006: DECO: desc idx 0: Invalid KEY command"
To ensure coherency, we require the key_mod, src and dst buffers to be
aligned to the cache line size and flush/invalidate the memory regions.
The same requirements apply to the job descriptor.
Tested on an i.MX6Q board.
Reviewed-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
As defined on reference board followed by Intel Edison a Bluetooth
device is attached to HSU0, i.e. PCI 0000:04.1.
Describe it in ACPI accordingly.
Note, we use BCM2E95 ID here as one most suitable for such device based
on the description in commit message of commit 89ab37b489d1
("Bluetooth: hci_bcm: Add support for BCM2E95 and BCM2E96")
in the Linux kernel source tree.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The recent commit 03c4749dd6c7
("gpio / ACPI: Drop unnecessary ACPI GPIO to Linux GPIO translation")
in the Linux kernel reveals the issue we have in ACPI tables here,
i.e. we must use hardware numbers for GPIO resources and,
taking into consideration that GPIO and pin control are *different* IPs
on Intel Tangier, we need to supply numbers properly.
Besides that, it improves user experience since the official documentation
for Intel Edison board is referring to GPIO hardware numbering scheme.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We only need to compile and link these files when building for full
U-Boot. Move them to under cmd/x86/ to make sure they aren't linked in
and undiscarded due to u_boot_list_2_cmd_* being included).
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since commit 051ba9e082 ("Kconfig: mx6ull: Deselect MX6UL from
CONFIG_MX6ULL") CONFIG_MX6ULL does not select CONFIG_MX6UL anymore, so
take this into consideration in all the checks for CONFIG_MX6UL.
This fixes a boot regression.
Reported-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Breno Lima <breno.lima@nxp.com>
Tested-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Jörg Krause <joerg.krause@embedded.rocks>
Boot scripts located in the root directory of the first partition of
USB, mmc, and SATA drives are executed twice: first by the distro boot
command and then by the legacy boot command. This may have weird side
effects if those scripts only change or extend the environment
(including parts of the boot command itself).
Removing the script execution from the legacy boot command has its own
caveats. For instance, the distro boot command may execute the boot.scr
on the mmc drive, then the boot.scr on the SATA drive, before the
legacy boot command actually boots from the mmc drive. However, the
current behavior would only execute the boot.scr once more before the
actual boot, but it does not prevent the script located on the SATA
drive from being executed, and thus, both scripts from being mixed up.
Considering that the legacy boot command is only in place to boot old
(standard) installations, let's go with the resolution having less
custom code and remove the script execution from the legacy boot
command.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The current default environment of the cm_fx6 is not suitable for
booting modern distributions.
Instead of extending the custom environment, let's use the distro
boot command, which has been developed for precisely this use case.
If the distro boot command fails, fall back to the old behavior
(except for USB drives where the old behaviour is completely covered
by the distro boot command). That way it is still possible to create
"rescue SD cards" for old installations (e.g. if one messes up the
on-flash environment).
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In preparation for supporting the distro boot command, introduce the
standard variables for specifying load addresses, which are documented
in README and doc/README.distro, and replace the custom variables
used so far with them.
Since the current address layout disregards an address for an initramfs,
also switch to the load addresses used and proven by other imx6 boards
(e.g. the wandboard and nitrogen6x), instead of going on with our own
way.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The Rockchip-released ATF for the Firefly apparently (i.e. Kever
reported this) does not tolerate a FDT being passed as the platform
parameter and will run into a hard stop.
To work around this limitation in the ATF parameter handling, we
enable SPL_ATF_NO_PLATFORM_PARAM (which will force passing NULL for
the platform parameters).
Note that this only affects this platform, as the ATF releases for the
RK3368 and RK3399 have always either ignored the platform parameter
(i.e. before the FDT-based parameters were supported) or support
receiving a pointer to a FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
While we expect to call a pointer to a valid FDT (or NULL) as the
platform parameter to an ATF, some ATF versions are not U-Boot aware
and have an insufficiently robust (or an overzealour) parameter
validation: either way, this may cause a hard-stop with uncooperative
ATF versions.
This change adds the option to suppress passing a platform parameter
and will always pass NULL.
Debug output from ATF w/ this option disabled (i.e. default):
INFO: plat_param_from_bl2: 0x291450
Debug output from ATF w/ this option enabled:
INFO: plat_param_from_bl2: 0
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
commit 20f1471416 ("imx: spl: Update NAND bootmode detection bit")
broke the NAND bootmode detection by checking if
BOOT_CFG1[7:4] == 0x8 for NAND boot mode.
This commit essentially reverts it, while using the IMX6_BMODE_*
macros that were introduced since.
Tables 8-7 & 8-10 from IMX6DQRM say the NAND boot mode selection
is done when BOOT_CFG1[7] is 1, but BOOT_CFG1[6:4] is not
necessarily 0x0 in this case.
Actually, NAND boot mode is when 0x8 <= BOOT_CFG1[7:4] <= 0xf,
like it was in the code before.
Signed-off-by: Eran Matityahu <eran.m@variscite.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tim Harvey <tharvey@gateworks.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The calculation of left space for version string is not correct, should
use VIDEO_COLS not VIDEO_LINE_LEN / 2, otherwise we will get larger space
than actual have and cause string to overlay logo picture.
Also current version string display only supports two lines words at max.
This also causes overlay when the LCD pixel column size is not enough.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Anatolij Gustschin <agust@denx.de>
The clk_set_rate function dereferences the clk pointer without
checking whether it is NULL. This may cause problem when clk is NULL.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We want to have the same configuration defaults for the RK3368-uQ7
as for the RK3399-Q7: this change reduces the default env-size to
8KiB to ensure that it does not overlap the boot-payload on SD/MMC
configurations.
References: commit fe529e6597 ("rockchip: rk3399-puma: reduce env size to 8kiB")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Khadas VIM is an Open Source DIY Box manufactured by Shenzhen Wesion NOT 'Tomato'
The fix was provided by Khadas Team member 'numbqq'.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The patch replaces the former error() by the new pr_err().
This makes the TPS65910 driver conform to Masahiro's patch
'treewide:replace with error() with pr_err()' introduced
October 2017.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit b6251db8c3 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND") removed CONFIG_BOOTCOMMAND option from
include/configs/am335x_evm.h file. But that option wasn't added to
defconfig files for BeagleBone Black board.
Because of this we can't boot Linux from SD card using just
"run bootcmd", getting next error:
** File not found /boot/undefined **
That's because "fdtfile" variable has "undefined" value by default, and
"bootcmd" doesn't call "run findfdt" command, which assigns "fdtfile" to
correct device tree file for current board name (obtained from EEPROM).
So we are forced to either call "run findfdt" command manually, or
assign manually "fdtfile=am335x-boneblack.dtb" (e.g. in uEnv.txt file).
Bring back CONFIG_BOOTCOMMAND to BBB defconfigs so that we can boot
Linux rootfs from SD card automatically without any addition actions.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
This commit clears 'ethaddr' before calling 'smc911x_initialize' to
allow the SROM MAC address to be assigned properly.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This commit updates the configuration files needed to support OF_CONTROL
on the OMAP3 EVM baseboard.
Additionally:
- CONFIG_SYS_THUMB_BUILD is enabled
- CONFIG_SPL_ENV_SUPPORT is enabled
Tested using GCC 7.2.0 [--with-float=hard --with-mode=thumb].
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
This commit adds OMAP3 EVM devicetree files from Linux v4.15-rc3. Note
that this is the first addition of OMAP34XX devicetree files.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Since commit 999a78d5cf ("scripts/dtc: Update to upstream version v1.4.5-3-gb1a60033c110")
dtc warns about:
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/serial@53fc0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/ccm@53fd4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@50000000/gpio@53fe4000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/sdma@63fb0000
arch/arm/dts/imx53-cx9020.dtb: Warning (interrupts_property): Missing interrupt-parent for /soc/aips@60000000/ethernet@63fec000
Fix this by adding a node for the tzic interrupt controller.
Copied from "<Linux>/arch/arm/boot/dts/imx53.dts"
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The DDR DRAM calibration doesn't work on T-topology sometimes, so disable it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
In commit 6e6cf015e7 ("Merge
git://www.denx.de/git/u-boot-imx") the line defining spl_sd
configuration for wandboard was removed, which resulted in no SPL
target being built.
Add it back.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently CONFIG_SECURE_BOOT is selecting FSL_CAAM for all i.MX devices,
this causes the following error when building mx6sl boards since
this SoC doesn't have the CAAM block:
In file included from drivers/crypto/fsl/jobdesc.c:12:0:
drivers/crypto/fsl/jobdesc.c: In function 'inline_cnstr_jobdesc_blob_dek':
include/fsl_sec.h:268:25: error: 'CAAM_ARB_BASE_ADDR' undeclared (first use
in this function)
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
include/fsl_sec.h:268:25: note: each undeclared identifier is reported only
once for each function it appears in
#define SEC_MEM_PAGE1 (CAAM_ARB_BASE_ADDR + 0x1000)
^
drivers/crypto/fsl/jobdesc.c:140:21: note: in expansion of macro 'SEC_MEM_PAGE1'
memcpy((uint32_t *)SEC_MEM_PAGE1, (uint32_t *)plain_txt, in_sz);
^
scripts/Makefile.build:280: recipe for target 'drivers/crypto/fsl/jobdesc.o'
failed
make[3]: *** [drivers/crypto/fsl/jobdesc.o] Error 1
scripts/Makefile.build:425: recipe for target 'drivers/crypto/fsl' failed
make[2]: *** [drivers/crypto/fsl] Error 2
scripts/Makefile.build:425: recipe for target 'drivers/crypto' failed
make[1]: *** [drivers/crypto] Error 2
Add HAS_CAAM configuration to avoid this error.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
MX6UL contains features that MX6ULL doesn't support.
Deselect CONFIG_MX6UL and select SYS_L2CACHE_OFF and ROM_UNIFIED_SECTIONS.
The motivation for doing this change is that MX6UL supports CAAM and
MX6ULL does not.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently the MX6SL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Secure boot is not enabled in warp imximage.cfg, add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for MMC. Remove the old mmc init code, which
is no longer used, from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for AHCI. Remove the old, now unused, sata
init code from the board file.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB. But it missed to enable driver
model support for keyboards. As a result, USB keyboards do no longer
work.
Fix this by enabling driver model support for keyboards.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
enabled driver model support for USB, thereby effectively removing USB
support because the cm_fx6 devicetree in the U-Boot does *not* enable the
USB nodes.
Reinstate the USB support by syncing the devicetree with Linux whose
devicetree enables the USB nodes properly.
More precisely, use the devicetree found in Linux v4.15-rc1 with the
following two changes:
1) Remove the audio mux; the required dt-bindings header is not
present in the U-Boot.
2) Keep the usdhc3 MMC controller node currently present in the
U-Boot's devicetree to retain the ability to boot from MMC.
Fixes: 5248930ebf ("dm: imx: cm_fx6: Enable more driver model support")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We are going to be using check_time() on more than the mx53ppd, move this
function to a common location.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
There is an #ifdef and #endif with nothing in between. This patch simply
removes this dead/useless code.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
In order to provide a consistent user experience for imx board users,
remove the custom CONFIG_BOOTDELAY values from defconfig files, so that
all boards can use the default two second delay.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.
It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.
Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
"ethernet" node fix-up for device tree happens before Linux boot.
There can be requirement of updating "ethernet" node even before
fix-up. So, add support of updating "ethernet" node.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The MAC addresses get fixed in the device tree for "ethernet" nodes
is by using trailing number behind "ethernet" found in "/aliases".
It may not be necessary for the "ethernet" nodes to be sequential.
There can be gaps in between or any node disabled
So provide a support to fetch MAC addr sequentially from env
and apply them to "ethernet" nodes in the order they appear in
device tree only if "ethernet" is not "disabled"
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When adding a partition, set the logical_partition member in the media
structure as mandated by the UEFI spec.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
and loading Image out of FIT image.
Loading Kernel Image ... Image too large: increase CONFIG_SYS_BOOTM_LEN
Must RESET board to recover
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When booting a itb file with a Ramdisk on a imx6 based
board, U-Boot drops the warning:
Loading Kernel Image ... OK
Loading Ramdisk to 4ecf1000, end 4ef8b11f ... \
CACHE: Misaligned operation at range [4ecf1000, 4ef8b11f]
Fix it!
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Ayoub Zaki <hs@denx.de>
Use dfu_alt_info_emmc variable from include/environment/ti/dfu.h file.
It was probably overlooked when extracting DFU variables to mentioned
file.
This patch fixes DFU on BeagleBone Black, so that we can use commands
like ones below to upgrade various images on eMMC:
=> setenv dfu_alt_info $dfu_alt_info_emmc
=> dfu 0 mmc 1
$ dfu-util -D MLO -a MLO.raw
$ dfu-util -D u-boot.img -a u-boot.img.raw
Without this patch, the user is forced to assign the value to
dfu_alt_info_emmc manually, which contradicts with instructions [1].
[1] http://processors.wiki.ti.com/index.php/Linux_Core_U-Boot_User%27s_Guide
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
This patch is ported from the Linux patch posted at [1] and applied to
net tree as commit f1e2400a80ff.
The purpose of this change is to fix the incorrect detection of the link
partner (LP) advertised capabilities which sometimes happens with this PHY
(roughly 1 time in a dozen)
This issue may cause the link to be negotiated at 10Mbps/Full or
10Mbps/Half when 100MBps/Full is actually possible. In some case, the link
is even completely broken and no communication is possible.
To detect the corruption, we must look for a magic undocumented bit in the
WOL bank (hint given by the SoC vendor kernel) but this is not enough to
cover all cases. We also have to look at the LPA ack. If the LP supports
Aneg but did not ack our base code when aneg is completed, we assume
something went wrong.
The detection of a corrupted LPA triggers a restart of the aneg process.
This solves the problem but may take up to 6 retries to complete.
[1] https://lkml.kernel.org/r/20171208110811.30789-1-jbrunet@baylibre.com
Fixes: 8995a96d1d ("net: phy: Add Amlogic Meson GXL Internal PHY support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Xilinx changes for v2018.01-rc2-v2
fpga:
- Enable loading bitstream via fit image for !xilinx platforms
zynq:
- Fix SPL SD boot mode
zynqmp:
- Not not reset in panic
- Do not use simple allocator because of fat changes
- Various dt chagnes
- modeboot variable setup
- Fix fpga loading on automotive devices
- Fix coverity issues
test:
- Fix env test for !hush case - Stephen's patch
Increase setup, assertion and hold time related to chip-select signal.
Additional delay is needed for the signal to propogate through FPGA.
This adjustment slightly increase the read and write cycle but has no
impact on burst read or write.
Signed-off-by: York Sun <york.sun@nxp.com>
Rockchip release bl31.elf file for armv8 SoCs like rk3399, rk3328,
the elf have more than one section, we need to decode it first and
packed them into u-boot.itb with its file. This script is to generate
the its script.
Need default bl31.elf in root directory of U-Boot source and dtb
as parameter.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip SoCs only need boot0 hook at SPL, and the U-Boot proper do not
need it.
The very beginning of U-Boot proper is different between armv7 and armv8:
armv7 start with ARM_VECTORS while armv8 start with 'b reset'.
Here is the map of very beginning for all cases:
armv7 SPL: TAG(overwrite 'b 1f')+'b reset' + ARM_VECTORS
armv7 U-Boot: ARM_VECTORS
armv8 SPL: TAG(overwrite 'b 1f')+'b reset' + Reserved_iram(rk3399)
armv8 U-Boot: 'b reset'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After adding our small zynq uboot which has hush parser off same
variable tests start to failed. Use quotes only when hush is enabled.
Reported-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Access the timestamp ref ctrl register only if runinng
at el3 level otherwise just return. This change fixes
the issue when CRL APB is marked as secure and accessing
when not in el3 causes exception.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Check all return values from file functions.
In case of negative return exit immediately.
Also change fsize return value which can't be negative.
Reported-by: Coverity (CID: 23276, 23304, 169357)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont use 4K sector erase by default, Disabling this
would use 64K sector erase and decreases erase time.
Also disabled by the fact that UBIFS and JFFS2 won't work
with 4K sector erase.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enabling all spi flashes because some of these boards can have different
flashes compared to public version.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adds ENV_SIZE and ENV_OFFSET configuration items for
ARCH_ROCKCHIP, but keeps these non-visible (i.e. not prompt is given).
With these new items present, the configuration from the header files
is moved to Kconfig.
Keeping these non-visible is necessary to have the possibility to
select new default values if CONFIG_IS_IN_* is changed (interactively
or with oldconfig). Otherwise it will always be set to a previous
value if used with a prompt. As an example if we do a defconfig with
CONFIG_IS_IN_MMC and change it to CONFIG_IS_IN_SPI_FLASH via
menuconfig, ENV_SIZE and ENV_OFFSET will not be changed to the correct
values as defconfig will already have set them to the default values
of CONFIG_IS_IN_MMC in .config.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Patch queue for efi - 2017-12-17
A few fixes for 2018.01:
- Compile fix with helloworld example
- DP match fix (fixes FreeBSD loader and grub on block storage)
- More DP fixes for SD, block
- Fix use-after-free
The PCIe reset signal is connected to GPIO4_C6 on the Puma
module. This pin is supplied by 1.8V, but the default iodomain
setting is 3.0V and in this situation the pin is unable to go
high.
Linux assumes that this signal works in early boot
as PCIe is probed before loading the iodomain driver.
Make PCIe work in Linux by setting the gpio4cd iodomain to 1.8V.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a description for dp_part_fill().
Reword a comment in the function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When converting device nodes and paths to text we should
stick to the UEFI spec.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
According to the UEFI spec the numbering of partitions has to
start with 1.
Partion number 0 is reserved for the optional device path for
the complete block device.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The SD cards and eMMC devices have different device nodes.
The current coding interpretes all MMC devices as eMMC.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If a failure occurs when trying to load an image, it is insufficient
to free() the EFI object. We must remove it from the object list,
too. Otherwise a use after free will occur the next time we
iterate over the object list.
Furthermore errors in setting up the image should be handled.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a function to remove a handle from the object list
after removing all protocols.
To avoid forward declarations other functions have to move up
in the coding.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_setup_loaded_image() should return an error code indicating if
an error has occurred.
An error occurs if a protocol cannot be installed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When calling efi_dp_find_obj(), we usually want to find the *exact* match
of an object for a given device path. However, I ran into a nasty corner case
where I had the following objects with paths available:
Handle 0x9feffa70
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]/USB(6,0)/EndEntire
Handle 0x9feffb58
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]/USB(6,0)/HD(1,800,32000,2de808cb00000000,1,1)/EndEntire
and was searching for
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]/USB(6,0)/HD(1,800,32000,2de808cb00000000,1,1)/EndEntire
But because our device path search looked for any substring match, it would
return
/HardwareVendor(e61d73b9-a384-4acc-aeab-82e828f3628b)[0: ]/USB(6,0)/EndEntire
because that path is a full substring of the path we were searching for.
So this patch adapts the device path search logic to always look for exact
matches first. The way we distinguish between those cases is by looking at
whether our caller actually deals with remainders.
As a side effect, the code as is from all I can tell now never does a
substring match anymore, because it always gets called with rem=NULL, so
we always only do exact matches now.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Signed-off-by: Alexander Graf <agraf@suse.de>
The efi linker script includes sections needed for the dynamic linker.
However, in our EFI application environment we don't have a dynamic linker.
So let's remove them. That way we save on 4k padding and reduce the file
size of the hello world efi binary from ~4k to ~1k.
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit bbf75dd934 ("efi_loader: output load options in helloworld")
introduced a const variable in efi_main() called loaded_image_guid which
got populated from a constant struct.
While you would usually expect a compiler to realize that this variable
should really just be a global pointer to .rodata, gcc disagrees and instead
puts it on the stack. Unfortunately in some implementations of gcc it does
so my calling memcpy() which we do not implement in our hello world
environment.
So let's explicitly move it to a global variable which in turn puts it in
.rodata reliably and gets rid of the memcpy().
Fixes: bbf75dd934 ("efi_loader: output load options in helloworld")
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and
detect it when u-boot starts up.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to clean up definitions for I2C IO expanders.
The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2.
Fixed it in this patch.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Function fdt_fixup_board_enet() performs fdt fixup. Only return
fdt_status_okay() when both MC is applied and DPL is deployed, else
return fdt_status_fail().
This check is added to LS1088A/LS2080A/LS2088A boards.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove silicon prefix. Automotive grade devices are using xazu instead
of xczu prefix.
The patch "fpga: xilinx: Check for substring in device ID validation"
(sha1: f72132673a)
enables this functionality for zynq devices that only substrings are
checked.
Unfortunately there is no way how to detect device grade that's why
this change is reasonable.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is the same patch as was done earlier.
Please look at Linux patch:
"arm64: zynqmp: Use only earlycon bootargs instead of full one"
(sha1: f3609c8d4af28b9cc22ca49bf8e529b582ec188c)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove overfetch, ratectrl, include-sg and src-issue dma properties.
Driver is not using them and they are also not documented in the binding
doc.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Kedareswara rao Appana <appanad@xilinx.com>
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup bootmode variable based on bootmode selection.
This is helping with setting up boot method.
Also setup sdbootdevice.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont read boot mode register directly read it using
zynqmp_mmio_read().
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling support for SPL QSPI boot.
First of all it is necessary to generate atf-spi.ub which is different
format than atf-uboot.ub (this can be made as legacy image too)
ADDR=`arm-xilinx-linux-gnueabi-readelf -a bl31.elf | grep "Entry point
address" | cut -d ':' -f 2 | sed -e 's/^[ \t]*//'`
aarch64-linux-gnu-objcopy -O binary bl31.elf bl31.bin
./tools/mkimage -f auto -A arm64 -T firmware -C none -O u-boot -a $ADDR
-e $ADDR -n "atf1" -E -b arch/arm/dts/zynqmp-zcu102.dtb -d bl31.bin
atf-uboot.ub
./tools/mkimage -A arm64 -T firmware -C none -O u-boot -a $ADDR -e $ADDR
-n "atf-for-qspi" -E -d bl31.bin atf-spi.ub
This patch is using this QSPI layout with offsets:
0 boot.bin
512k atf-ub
640k u-boot.bin
1280k u-boot.img
Which corresponding by writing these images(read from MMC)
mmcinfo
sf probe
load mmc 0 10000000 boot.bin
sf erase 0 +$filesize
sf write 10000000 0 $filesize
load mmc 0 10000000 atf-spi.ub
sf erase 0x80000 +$filesize
sf write 10000000 0x80000 $filesize
load mmc 0 10000000 u-boot.bin
sf erase 0xa0000 +$filesize
sf write 10000000 0xa0000 $filesize
load mmc 0 10000000 u-boot.img
sf erase 0x140000 +$filesize
sf write 10000000 0x140000 $filesize
For testing u-boot running in EL3 you can break atf-spi.ub like this:
sf probe
sf erase 0x80000 +4
Then u-boot.img is executed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This reference is needed for pinctrl driver where some signals can be
routed directly to platform management unit (PMU).
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This was caused by: "fs/fat: Reduce stack usage"
(sha1:2460098cffacd18729262e3ed36656e6943783ed) which converted
fat code to use malloc. But simple malloc is not freeing space
that's why full malloc implementation is needed.
Malloc space is added to RAM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not perform reset when panic happens because in the next reset
panic happens again and logs are overflood by the same errors.
This can be enabled by default and reset can be performed via watchdog.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is fixing two issues:
1. Insufficient stack size for fat fs buffers
2. Insufficient space in malloc area
Tested on zc702 and zc706.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This drops the limit that fpga is only loaded from FIT images for Xilinx.
This is done by moving the 'partial' check from 'common/image.c' to
'drivers/fpga/xilinx.c' (the only driver supporting partial images yet)
and supplies a weak default implementation in 'drivers/fpga/fpga.c'.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (On zcu102)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Using "cpu_pos_mask()" function to detect the real online cpus,
and discard the needless cpu nodes on kernel dts.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Check LS1043A/LS2080a by device ID without using personality ID to
determine revision number. This check applies to all various
personalities of the same SoC family.
Signed-off-by: Wenbin Song <wenbin.song@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Include common config_distro_defaults.h and config_distro_bootcmd.h
for u-boot enviroments to support automatical distro boot which
scan boot.scr from external storage devices(e.g. SD and USB)
and execute autoboot script.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The BRDCFG5[SPISDHC] register field of Qixis device is used
to control SPI and SDHC signal routing.
10 = Force SDHC Mode
- SPI_CS[0] is routed to CPLD for SDHC_VS use.
- SPI_CS[1] is unused.
- SPI_CS[2:3] are routed to the TDMRiser slot.
11 = Force eMMC Mode
- SPI_CS[0:3] are routed to the eMMC card.
0X = Auto Mode
- If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode
described above.
- Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC
mode described above.
In default the hardware uses auto mode, but sometimes we need
to use force SDHC mode to support SD card hotplug, or SD sleep
waking up in kernel. This patch is to support force SDHC mode
by hwconfig.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Texas Instrument's TPS65910 PMIC contains 3 buck DC-DC converts, one
boost DC-DC converter and 8 LDOs. This patch implements driver model
support for the TPS65910 PMIC and its regulators making the get/set
API for regulator value/enable available.
This patch depends on the patch "am33xx: Add a function to query MPU
voltage in uV" to build correctly. For boards relying on the DT
include file tps65910.dtsi the v3 patch "power: extend prefix match
to regulator-name property" and an appropriate regulator naming is
also required.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch changes the calls to uclass_first/next_device() in blk_first/
next_device() to use uclass_find_first/next_device() instead. These functions
don't prepare the devices, which is correct in this case.
With this patch applied, the "usb storage" command now works again as
expected:
=> usb storage
Device 0: Vendor: SanDisk Rev: 1.00 Prod: Ultra
Type: Removable Hard Disk
Capacity: 58656.0 MB = 57.2 GB (120127488 x 512)
Without this patch, it used to generate this buggy output:
=> usb storage
Card did not respond to voltage select!
mmc_init: -95, time 26
No storage devices, perhaps not 'usb start'ed..?
Signed-off-by: Stefan Roese <sr@denx.de>
Suggested-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DM version of do_reset has been issuing a warm-reset, which (on
some platforms keeps GPIOs and other parts of the platform active).
This may cause unintended behaviour, as calling do_reset usually
indicates a desire to reset the board/platform and not just the CPU.
This changes do_reset to always request a COLD reset.
Note that programmatic uses can still invoke a WARM reset through
reset_cpu() or using sysreset_walk().
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update tegra to use binman for image creation. This still includes the
current Makefile logic, but a later patch will remove this. Three output
files are created, all of which combine
SPL and U-Boot:
u-boot-tegra.bin - standard image
u-boot-dtb-tegra.bin - same as u-boot-tegra.bin
u-boot-nodtb-target.bin - includes U-Boot without the appended device tree
The latter is useful for build systems where the device is appended later,
perhaps after being modified.
Signed-off-by: Simon Glass <sjg@chromium.org>
SPL supports reading U-Boot from a RAM location. At present this is
hard-coded to the U-Boot text base address. Use binman to allow this to
come from the image file, if binman is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Allow SPL to access binman symbols and use this to get the address of
U-Boot. This falls back to CONFIG_SYS_TEXT_BASE if the binman symbol
is not available.
Signed-off-by: Simon Glass <sjg@chromium.org>
This area of the image contains symbols whose values are filled in by
binman. If this feature is not used, the table is empty.
Add this to the ARM SPL link script.
Signed-off-by: Simon Glass <sjg@chromium.org>
Binman construct images consisting of multiple binary files. These files
sometimes need to know (at run timme) where their peers are located. For
example, SPL may want to know where U-Boot is located in the image, so
that it can jump to U-Boot correctly on boot.
In general the positions where the binaries end up after binman has
finished packing them cannot be known at compile time. One reason for
this is that binman does not know the size of the binaries until
everything is compiled, linked and converted to binaries with objcopy.
To make this work, we add a feature to binman which checks each binary
for symbol names starting with '_binman'. These are then decoded to figure
out which entry and property they refer to. Then binman writes the value
of this symbol into the appropriate binary. With this, the symbol will
have the correct value at run time.
Macros are used to make this easier to use. As an example, this declares
a symbol that will access the 'u-boot-spl' entry to find the 'pos' value
(i.e. the position of SPL in the image):
binman_sym_declare(unsigned long, u_boot_spl, pos);
This converts to a symbol called '_binman_u_boot_spl_prop_pos' in any
binary that includes it. Binman then updates the value in that binary,
ensuring that it can be accessed at runtime with:
ulong u_boot_pos = binman_sym(ulong, u_boot_spl, pos);
This assigns the variable u_boot_pos to the position of SPL in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
The elf module can provide some debugging information to assist with
figuring out what is going wrong. This is also useful in tests. Update the
-D option so that it is passed through to tests as well.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is only 3 bytes long which is not enough to hold two symbol values,
needed to test the binman symbols feature. Increase it to 15 bytes.
Using very small regions is useful since we can easily compare them in
tests and errors are fairly easy to diagnose.
Signed-off-by: Simon Glass <sjg@chromium.org>
For testing we need to build some ELF files containing binman symbols. Add
these to the Makefile and check in the binaries:
u_boot_binman_syms - normal, valid ELF file
u_boot_binman_syms_bad - missing the __image_copy_start symbol
u_boot_binman_syms_size - has a binman symbol with an invalid size
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we need to read symbols from U-Boot. At present we have a
a few cases which does this via 'nm' and 'grep'.
It is better to use objdump since that tells us the size of the symbols
and also whether it is weak or not.
Add a new module which reads ELF information from files. Update existing
uses of 'nm' to use this module.
Signed-off-by: Simon Glass <sjg@chromium.org>
The old CodingStyle document has been converted to ReST and moved
elsewhere. Link to the web version of this document instead.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
These ifdefs are protecting #include statements for files that have
never existed. AFAICT this hardware.h has been copied from the kernel
and the ifdefs have never served a role in U-Boot, so delete them.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Some QEMUs have a problem with time setup that's why
sleep test is failing. Introduce env__sleep_accurate
boardenv variable to have an option to skip sleep test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
- avoid disturbing 0MiB partition size (in fact < 1MiB)
- test overlap limit between part1 and part2
- test gpt write with data with modifier 'M' for MiB
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Falcon mode was already working with SD card. This enables the
unlocking of NAND to allow the NAND read & write. This also
expands the README file based on the am335x describing how to
setup Falcon mode.
Signed-off-by: Adam Ford <aford173@gmail.com>
The Micron Flash is locked by default. This will automaticlly
unlock so manually unlocking is unnecessary in U-Boot.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL-OS partition is 0x20000, so let's make
CONFIG_CMD_SPL_WRITE_SIZE same size. This should allow for better
falcon mode operation.
Signed-off-by: Adam Ford <aford173@gmail.com>
This symbol enables some library code used by various SATA drivers,
so make this a non-user-visible symbol select'ed by the respective
drivers, and let moveconfig handle the rest.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Use 'imply' here liberally to avoid the combinatorial explosion of
defconfig changes in the PowerPC boards.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The last user of this driver went away in August 2015 in commit:
b6073fd211 ("arm: Remove mx51_efikamx, mx51_efikasb boards")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The last user of this driver went away in June 2017, in commit:
98f705c9ce ("powerpc: remove 4xx support")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
This driver really is DM GPIO one and so we need to have a correct
dependency, because DM alone doesn't provide required for CMD_GPIO
call and we're seeing build failures like this:
---------------------->8---------------------
cmd/built-in.o: In function 'do_gpio':
.../cmd/gpio.c:188: undefined reference to 'gpio_request'
...
---------------------->8---------------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is tedious to define both mask and bit-shift. <linux/bitfield.h>
provides a convenient way to get access to register fields with a
single shifted mask.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use DIV_ROUND_CLOSEST(). To make the JK value even more precise,
I used a bigger coefficient, then divide it by 512.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
missed to write the computed value to the SSCPLLCTRL2 register.
Fixes: 682e09ff9f ("ARM: uniphier: add PLL init code for LD20 SoC")
Signed-off-by: Dai Okamura <okamura.dai@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
denali.c has no driver entry in itself. It makes sense only when
compiled together with denali_dt.c
Let NAND_DENALI_DT select NAND_DENALI, and hide NAND_DENALI from
the Kconfig menu.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix the link error for the combination of
CONFIG_ARCH_UNIPHIER_LD11=n
CONFIG_ARCH_UNIPHIER_LD20=n
CONFIG_ARCH_UNIPHIER_PXS3=y
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
dcache_exists, icache_exists, slc_exists and ioc_exists global
variables in "arch/arc/lib/cache.c" remain uninitialized if
SoC doesn't have corresponding HW.
This happens because we use the next constructions for their
definition and initialization:
-------------------------->>---------------------
int ioc_exists __section(".data");
if (/* condition */)
ioc_exists = 1;
-------------------------->>---------------------
That's quite a non-trivial issue as one may think of it.
The point is we intentionally put those variables in ".data" section
so they might survive relocation (remember we initilaize them very early
before relocation and continue to use after reloaction). While being
non-initialized and not explicitly put in .data section they would end-up
in ".bss" section which by definition is filled with zeroes.
But since we place those variables in .data section we need to care
about their proper initialization ourselves.
Also while at it we change their type to "bool" as more appropriate.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARCNUM [15:8] field in ARC_AUX_IDENTITY register allows us to
uniquely identify each core in a multi-core system.
I.e. with help of this macro each core may get its index in SMP system.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
DW SDIO controller has external CIU clock divider controlled via
register in the SDIO IP. Due to its unexpected default value
(we expected it to divide by 1 but in reality it divides by 8)
SDIO IP uses wrong CIU clock (it should be 100000000Hz but actual
is 12500000Hz) and works unstable (see STAR 9001204800).
So increase SDIO CIU frequency from actual 12500000Hz to 50000000Hz
by switching from the default divisor value (div-by-8) to the
minimum possible value of the divisor (div-by-2) in HSDK platform
code.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable all logging features on sandbox so that the tests can be run.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to display log messages on the console. Add a simple driver
to handle this.
Note that this driver outputs to the console, which may be serial or
video. It does not specifically select serial output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This does not appear to be used by any boards. Before introducing a new
log system, remove this old one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With clang this gives a warning because hubsts appears to be used before
it is set, even if ultimately it is not used. Simplify the code to avoid
this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
The debug() macro now evaluates its expression so does not need #ifdef
protection. In fact the current code causes a warning with the new log
implementation. Adjust the code to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Before adding new features, move these definitions to a separate header
to avoid further cluttering common.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While sandbox works OK without the special-case code, it does result in
console output being stored in the pre-console buffer while sandbox starts
up. If there is a crash or a problem then there is no indication of what
is going on.
For ease of debugging it seems better to revert this change also.
This reverts commit d8c6fb8ced.
Signed-off-by: Simon Glass <sjg@chromium.org>
We cannot use sandbox memory at 0 since other things use memory at that
address. Move it up out of the way.
Note that the pre-console buffer is currently disabled with sandbox, but
this change will avoid confusion if it is manually enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
While sandbox works OK without the special-case code, it does result in
console output being stored in the pre-console buffer while sandbox starts
up. If there is a crash or a problem then there is no indication of what
is going on.
For ease of debugging it seems better to revert this change.
This reverts commit 47b98ad0f6.
Signed-off-by: Simon Glass <sjg@chromium.org>
The A33-OLinuXino defconfig was using the default CONS_INDEX value for
A33, which actually points to the R_UART, which is routed to the GPIO
header without proper pull-ups or diodes. The board has a separate
header for UART0, which are routed to pins PB0 and PB1. This header
is properly marked and is likely the first pins any user would try
to get a console.
Fix CONS_INDEX in the defconfig so the console appears on UART0.
Fixes: ca5c37026b ("sunxi: Add support for A33-OLinuXino board")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that more and more devices are built using eMMC, providing a way to
easily flash the system without too much hassle seems like a right thing to
do.
Since fastboot is the most deployed tool to do that these days, we can just
rely on it to provide a way to flash the various components in the system
(SPL, U-Boot and the system itself) easily, especially since you can upload
the U-Boot hosting the fastboot "server" through FEL.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The partitions variable is especially useful to create a partition table
from U-Boot, either directly from the U-Boot shell, or through flashing
tools like fastboot and its oem format command.
This is especially useful on devices with an eMMC you can't take out to
flash from another system, and booting a Linux system first to flash our
system then is not really practical.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SPL must be located at 8kB (16 sectors) offset. That's right in the
middle of the GPT, so we need to define a smaller amount of partitions to
accomodate for that location.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On some SoCs, the SPL needs to be located right in the middle of the GPT
partition entries.
One way to work around that is to create partition entries for a smaller
number of partitions to accomodate with where the SPL will be. Create a
Kconfig option to allow to do that.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sdram sub command of i2c command does not support Drivers Model.
This adds Drivers Model support to sdram sub command.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The .probe_chip function is supposed to probe an i2c device on the bus to
determine whether a device is answering to a particular address.
at91_i2c_probe_chip() did not do anything resembling this and always
returned 0.
It looks as though at91_i2c_probe_chip() was intended to be a .probe
function for the controller, as it was copied-and-pasted to become
at91_i2c_probe() in 0bc8f640a4.
Removing the at91_i2c_probe_chip() function makes the higher layer
(i2c_probe_chip()) try a zero-length read transfer to test for the
presence of a device instead, which does work.
Signed-off-by: Alan Ott <alan@softiron.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The driver must wait for TXRDY after each byte is pushed into
the i2c FIFO before pushing the next byte. Previously this was
not done for the first byte, causing a race condition with zeros
sometimes being sent for the next byte (which is typically the
first actual data byte).
Signed-off-by: Alan Ott <alan@softiron.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add some comment describing the purpose of struct members and
functions.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change meson_i2c_xfer_msg() to return -EREMOTEIO in case of NACK, as
done by other drivers. Also, don't change the return error in
meson_i2c_xfer().
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The datasheet doesn't specify a suggested timeout and 500ms seems very
long: reduce it to 100ms.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
>From revision J the board uses new phy chip LAN8710. Compared
with RTL8201, RA17 pin is TXERR. It has pullup which causes phy
not to work. To fix this PA17 is muxed with GMAC function. This
makes the pin output-low.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
For case when MC is loaded but DPL is not deployed perform MC
object [DPBP, DPIO, DPNI and DPRC] cleanup.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add fall back option, to boot from NOR/QSPI/SD for LS1043, LS1046,
LS1021 in case of distro boot failure.
For LS1046, add kernel validation in case of secure boot in sd_bootcmd
and qspi_bootcmd. For LS1043 and LS1021, add kernel validation in case
of secure boot in sd_bootcmd, qspi_bootcmdand nor_bootcmd.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds config CONFIG_FSL_LS_PPA and CONFIG_FSL_CAAM in
LS2080AQDS and LS2080ARDB secure boot defconfig.
Removes CONFIG_FIT, as with CONFIG_FSL_LS_PPA enabled,
CONFIG_FIT is selected.
Removes CONFIG_SPL_RSA as in NOR boot SPL boot is not done.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the secure boot defconfigs for QSPI boot on LS1088ARDB
and LS1088AQDS platforms.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Kernel is now located at 0x1000000 instead of 0xa00000
and envirorment variables are located at 3MB offset instead of
2MB in Flash.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is suplement for patch which handle below errata:
A-009007, A-009008, A-008997, A-009798
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Instruction prefetch feature is by default enabled during core
release. This patch add support of disabling instruction prefetch
by setting core mask in PPA. Here each core mask bit represents a
core and prefetch is disabled at the time of core release.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IFC-NOR and QSPI-NOR signals are muxed on SoC to save pins
Add fsl_fdt_fixup_flash() to disable IFC-NOR node in dts
if QSPI is enabled and vice-versa
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Existing MC driver framework is based on MC-9.x.x flib. This patch
migrates MC obj (DPBP, DPNI, DPRC, DPMAC etc) to use latest MC flib
which is MC-10.3.0.
Changes introduced due to migration:
1. To get OBJ token, pair of create and open API replaces create APIs
2. Pair of close and destroy APIs replaces destroy APIs
3. For version read, get_version APIs replaces get_attributes APIs
4. dpni_get/reset_statistics APIs replaces dpni_get/set_counter APIs
5. Simplifies struct dpni_cfg and removes dpni_extended_cfg struct
6. Single API dpni_get_buffer_layout/set_buffer_layout replaces
dpni_get_rx/set_rx, tx related, tx_conf_buffer_layout related APIs.
New API takes a queue type as an argument.
7. Similarly dpni_get_queue/set_queue replaces
dpni_get_rx_flow/set_rx_flow , tx_flow related, tx_conf related
APIs
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Unset USE_BOOTCOMMAND for all ls1088 defconfig files to fix
redefinition error. USE_BOOTCOMMAND was introduced in commit
b6251db8c3 ("Kconfig: Introduce USE_BOOTCOMMAND and migrate
BOOTCOMMAND").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Most predefined TLB tables don't have memory coherence bit set for
SDRAM. This wasn't an issue before invalidate_dcache_range() function
was enabled. Without the coherence bit, dcache invalidation doesn't
automatically flush the cache. The coherence bit is already set when
dynamic TLB table is used. For some boards with different SPL boot
method, or with legacy fixed setting, this bit needs to be set in
TLB files.
Signed-off-by: York Sun <york.sun@nxp.com>
This issue is exposed after commit 9000eddbae ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This issue is exposed after commit 9000eddbae ("drivers/usb/ehci:
Use platform-specific accessors"), the wrong endianness of EHCI
controller programing will cause USB function down.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since commit 2614a20847 ("common: command: tempory buffer should
have size of command line buf"), there have been consistent Travis CI
failures on my builds (interestingly not for Tom, even though building
the same commit id) due to a SEGV in building the byteswapped
omapimage:
arm: pcm051_rev3
make[2]: *** [MLO.byteswap] Error 139
^^^ error code for a SEGV
Turns out that the word-based byte-swapping loop in omapimage.c is to
blame. With the loop condition
while (swapped <= (sbuf->st_size / sizeof(uint32_t)))
there had been one-too-many iterations for all file sizes divisible by
the sizeof(uint32_t). I.e. we had 1 iteration for 0 bytes (and also 1
through 3 bytes) and 2 iterations at 4 bytes... clearly overshooting
on 0 and 4 bytes.
This commit fixes the calculation of an up-rounded word-count and
makes sure to keep the zero-based loop-counter below the number of
words to be processed.
References: 2614a20 ("common: command: tempory buffer should have size of command line buf")
Fixes: 79b9ebb ("omapimage: Add support for byteswapped SPI images")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Martin Elshuber <martin.elshuber@theobroma-systems.com>
Commit f5a2a93892 ("efi_loader: consistently use efi_uintn_t in boot
services") changed the internal EFI API header without adapting its existing
EFI stub users. Let's adapt the EFI stub as well.
Fixes: f5a2a93892 ("efi_loader: consistently use efi_uintn_t in boot services")
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Odroid HC1 board is based on Odroid XU4 board, but it has no HDMI,
no eMMC, no build-in USB3.0 hub, no extension port pins, and no GPIO
button. USB3.0 ports are used for build-in JMicron USB to SATA bridge
and Gigabit R8152 ethernet chips. HC1 uses only passive cooling.
This patch also updates Odroid's ADCmax array and reduces ADC tolerance
to 1% to ensure that XU4 and HC1 revisions are properly detected.
I've tested this with XU3, XU3-lite, XU4 and HC1 boards. In case of my test
boards I got following values from ADC register: 372, 370, 1281 and 1313.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
After updating dtc-1.4.5 version, there are too many warning.
This patch is to fix about exynos4 series.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In Linux, the warning messages are printed out by pr_warn().
We can use Linux-like log functions in tree-wide.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[primary] Check MMC 0:1 for /extlinux/extlinux.conf and boot
[fallback 1] Check MMC 0:1 zImage and run mmcbootz
[fallback 2] Check MMC 0:1 uImage and run mmcboot
[fallback 3] Check NAND partitions and run nandboot
If 'extlinux.conf' is not found on MMC 0, the previous boot behavior is
followed.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
To page mapping the lowest 2 bits needs to be 0x3.
If not fix this, the final lowest 3 bits for page mapping is 0x1
which is marked as reserved.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
After relocation, when error happends, it is hard to track
ELR and LR with asm file objdumped from elf file.
So subtract the gd->reloc_off the reflect the compliation address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As discussed at [1], the Amlogic Meson GX SoCs can embed a BL31 firmware
and a secondary BL32 firmware.
Since mid-2017, the reserved memory address of the BL31 firmware was moved
and grown for security reasons.
But mainline U-Boot and Linux has the old address and size fixed.
These SoCs have a register interface to get the two firmware reserved
memory start and sizes.
This patch adds a dynamic reservation of the memory zones in the device tree bootmem
reserved memory zone used by the kernel in early boot.
To be complete, the memory zones are also added to the EFI reserved zones.
Depends on patchset "Add support for Amlogic GXL Based SBCs" at [2].
[1] http://lists.infradead.org/pipermail/linux-amlogic/2017-October/004860.html
[2] http://lists.infradead.org/pipermail/linux-amlogic/2017-November/005410.html
Changes since v1:
- switched the #if to if(IS_ENABLED()) to compile all code paths
- renamed function to meson_board_add_reserved_memory()
- added a mem.h header with comment
- updated all boards ft_board_setup()
Changes since RFC v2:
- reduced preprocessor load
- kept Odroid-C2 static memory mapping as exception
Changes since RFC v1:
- switch to fdt rsv mem table and efi reserve memory
- replaced in_le32 by readl()
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[trini: Fix warning on khadas-vim over missing <asm/arch/mem.h>
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.
The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch P212 Ethernet init to the common Ethernet init function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch Odroid-C2 Ethernet init to the common Ethernet init function.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a generic common Ethernet Hardware init function
common to all Amlogic GX SoCs with support for the
Internal PHY enable for GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Now, lib/libfdt/fdt_wip.c is the same as scripts/dtc/libfdt/fdt_wip.c
Change the former to a wrapper of the latter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All the other fdt_*_region() functions are located in fdt_region.c,
while only fdt_find_regions() was added to fdt_wip.c, strangely.
Move it to the suitable place.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the moment our exception entry code needs 34 instructions, so we
can't use put it directly into the table entry, which offers "only"
32 instructions there. Right now we just put an unconditional branch
there, then use a macro to place the 34 instructions *per entry* after
that. That effectivly doubles the size of our exception table, which
is quite a waste, given that we use it mostly for debugging purposes.
Since the register saving part is actually identical, let's just convert
that macro into a function, and "bl" into it directly from the exception
slot, of course after having saved at least the original LR.
This saves us about 950 bytes of code, which is quite a relief for some
tight SPLs, in particular the 64-bit Allwinner ones.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Adjust this test to use the unit test framework. Drop the two existing
commands for running the tests and replace them with a single
'ut compression' command, with sub-commands.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Continue to have ret = run_test_internal(...) in run_test so ret
is always initialized]
Signed-off-by: Tom Rini <trini@konsulko.com>
Include necessary headers explicitly without relying on indirect
header inclusion.
<common.h>, <malloc.h> are unneeded.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Linux derived log functions can be used anywhere and easily
turned on/off by CONFIG_LOGLEVEL.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This driver is highly dependent on the configuration from denali_dt.c
Please enable CONFIG_NAND_DENALI_DT if you use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
denali_setup_data_interface() is always used.
I put __maybe_unused for a temporal use, then forgot to delete it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Remove unnecessary DECLARE_GLOBAL_DATA_PTR and header includes.
<common.h> has been replaced with <linux/errno.h> and <linux/printk.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 72443c7f7d ("mtd: cfi: Add support for status register
polling") added a feature check to determine if status register
is available for certain flash chips. The "lower software bits"
register used to determine this feature is not backward compati-
ble. Older flash chips without this feature has reserved value
0xff. Instead of checking "lower software bits" register, use
CFI primary vendor-specific extended query. Since CFI version
1.4, software features can be read from offset 0x53 according to
document AN201168 from Cypress.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The u-boot.sym file is scanned to find unit test suites for execution. At
present it only finds those whose names start with 'dm' or 'env'. This
code is buried in the bowels of the test code so when adding a new suite
it is not easy to discover why it is ignored by the test framework.
There seems to be no need to make this restriction. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
At present the test setup is somewhat mixed with the test itself. But if
the test setup fails (which it should not) then the test is actually
invalid. Put all the test buffers and sizes in a struct and separate out
the core code into a function.
This will make it easier to move the code to use the unit test framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
The logic to either iterate through a list of tests or pick a named test
is common to at lest two test suits. Move this logic into a new function
and call it from the environment tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
The kernel gets the ethernet MAC from the ethaddr variable, the omap boards for
devices with USB based eth adapters just set the usbethaddr which doesn't appear
to get passed to the kernel. The same Raspberry Pi code sets both ethaddr and
usbethaddr so lets do that so linux (tested 4.13 and 4.14) get a static rather
than a random MAC address, while not regressing users of usbethaddr.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
These are actually different bits, and since some monitors (Benq BL2420PT)
have modes with different HSYNC and VSYNC polarity, we should set them
independently
Tested on Pine64-LTS with Benq BL2420PT monitor.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Some H5 boards are designed to start at 1.1V CPUx voltage (e.g. Nano Pi
NEO2), which may not work properly at 1008MHz if the chip's quality is
not so good.
Lower the default CPUx frequency of H5 to 816MHz.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The DCLK_VOP_DIV_CON_MASK should cover only bits 8 through 15.
Fix this to remove an "integer-overflow on shifted constant" warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The PLL selector field for NANDC is only 2 bits wide.
This fixes an 'int-overflow on shift' warning.
Fixes: 9246d9e ("rockchip: rk3128: add clock driver")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Depending on your compiler, when compiling the hello world efi binary
with -Os, gcc might think it's a smart idea to replace common patterns
such as memory copies with explicit calls to memcpy().
While that sounds great at first, we don't have any memcpy() available
in our helloworld build target. So let's indicate to gcc that we really
do want to have the code be built as freestanding.
Fixes: bbf75dd9 ("efi_loader: output load options in helloworld")
Signed-off-by: Alexander Graf <agraf@suse.de>
Commit 884bcf6f65 (efi_loader: use proper device-paths for partitions) tried
to introduce the el torito scheme to all partition table types: Spawn
individual disk objects for each partition on a disk.
Unfortunately, that code ended up creating partitions with offset=0 which meant
that anyone accessing these objects gets data from the raw block device instead
of the partition.
Furthermore, all the el torito logic to spawn devices for partitions was
duplicated. So let's merge the two code paths and give partition disk objects
good offsets to work from, so that payloads can actually make use of them.
Fixes: 884bcf6f65 (efi_loader: use proper device-paths for partitions)
Reported-by: Yousaf Kaukab <yousaf.kaukab@suse.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Otherwise with GUID partition types you would end up with things like:
.../HD(Part0,Sig6252c819-4624-4995-8d16-abc9cd5d4130)/HD(Part0,MBRType=02,SigType=02)
Signed-off-by: Rob Clark <robdclark@gmail.com>
[agraf: rebased]
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide comments for efi_convert_device_node_to_text()
and efi_convert_device_path_to_text().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
To avoid duplicate coding provide a helper function that
initializes an EFI object and adds it to the EFI object
list.
efi_exit() is the only place where we dereference a handle
to obtain a protocol interface. Add a comment to the function.
Suggested-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The handle of a loaded image is the value of the handle
member of the loaded image info object and not the
address of the loaded image info.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Check that helloworld.efi returns EFI_SUCCESS.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We need to test if we pass a valid image handle when loading
and EFI application. This cannot be done in efi_selftest as
it is not loaded as an image.
So let's enhance helloworld a bit.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Add a missing line feed for an error message.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
As the selftest is not compiled as an EFI binary we do not
need special compiler flags.
This avoids the checkarmreloc error on vexpress_ca15_tc2.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use efi_add_protocol to install protocols.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a test for the EFI_DEVICE_PATH_TO_TEXT_PROTOCOL protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current implementation of efi_locate_device_path does not match
the UEFI specification. It completely ignores the protocol
parameters.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We need to implement to different functions for the
EFI_DEVICE_PATH_TO_TEXT_PROTOCOL:
ConvertDeviceNodeToText
ConvertDevicePathToText
A recent patch screwed up efi_convert_device_node_to_text
to expect a device path and not a node.
The patch makes both service functions work again.
efi_convert_device_node_to_text is renamed to
efi_convert_single_device_node_to_text and
efi_convert_device_node_to_text_ext is renamed to
efi_convert_device_node_to_text to avoid future
confusion.
A test of ConvertDeviceNodeToText will be provided in
a follow-up patch.
Fixes: adae4313cd efi_loader: flesh out device-path to text
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_dp_str is meant to print a device path and not a device
node.
The old coding only worked because efi_convert_device_node_to_text
was screwed up to expect paths instead of nodes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the format specifier we want to specify the maximum width
in case an ending \0 is missing.
So slen must be used as precision and not as field width.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When trying to load an image from a non-existent USB key, U-Boot v2017.11
crashes on my x86 platform:
=> load usb 0:1 03000000 abc
General Protection
EIP: 0010:[<7b59030d>] EFLAGS: 00010286
Original EIP :[<fff4330d>]
...
This used to work in v2017.09. Testing has shown, that this bug was
introduced with patch 95c5553e [efi_loader: refactor boot device and
loaded_image handling].
This patch now checks if a valid "desc" is returned from blk_get_dev()
and only continues when "desc" is available. Resulting in this cmd
output (again):
=> load usb 0:1 03000000 abc
** Bad device usb 0 **
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Zero partition_signature in the efi_device_path_hard_drive_path
structure when signature_type is 0 (no signature) as required by the
UEFI specification.
This is required so that efi_dp_match() will work as expected
when doing memcmp() comparisons. Previously uninitialised memory
would cause it not match nodes when it should have when the signature
type was not GUID.
Corrects a problem where the loaded image protocol would not return a
device path with MEDIA_DEVICE causing the OpenBSD bootloader to fail
on rpi_3 and other targets.
v2: Also handle signature_type 1 (MBR) as described in the specification
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Tested-by: Artturi Alm <artturi.alm@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use helper functions efi_created_handle and efi_add_protocol
for creating the console handles and instaling the respective
protocols.
This change is needed if we want to move from an array of
protocols to a linked list of protocols.
Eliminate EFI_PROTOCOL_OBJECT which is not used anymore.
Currently we have not defined protocol interfaces to be const.
So efi_con_out and efi_console_control cannot be defined as const.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use helper function efi_search_protocol.
Do not print protocol guid twice in debug mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use function efi_search_obj, efi_search_protocol and
efi_remove_protocol to simplify the coding.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use helper function efi_search_protocol in efi_search.
Add missing comments.
Put default handling into default branch of switch statement.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This patch provides helper functions to manage protocols.
efi_search_protocol - find a protocol on a handle
efi_add_protocol - install a protocol on a handle
efi_remove_protocol - remove a protocol from a handle
efi_remove_all_protocols - remove all protocols from a handle
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use efi_uintn_t instead of unsigned long.
EFI_GRAPHICS_OUTPUT_BLT_OPERATION is an enum. If we don't
define an enum we have to pass it as u32.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The argument of efi_search_obj is not changed so it should
be marked as const.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_dp_match does not change its arguments.
So they should be marked as const.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calloc may return NULL. So we must check the return value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calloc may return NULL. We should check the return value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calloc may return NULL. We have to check the return value.
Fixes: be8d324191 efi_loader: Add GOP support
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Implement UninstallMultipleProtocolInterfaces.
The efi_uninstall_multipled_protocol_interfaces tries to
uninstall protocols one by one. If an error occurs all
uninstalled protocols are reinstalled.
As the implementation efi_uninstall_protocol_interface is
still incomplete the function will fail.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_install_protocol_interface should provide the created or
provided handle in the debug output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
EFI_HANDLEs are used both in boottime and in runtime services.
efi_search_obj is a function that can be used to validate
handles. So let's make it accessible via efi_loader.h.
We can simplify the coding using list_for_each_entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Check the parameters in efi_locate_handle.
Use list_for_each_entry instead of list_for_each.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Consistenly use efi_uintn_t wherever the UEFI spec uses
UINTN in boot services interfaces.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
UINTN is used in the UEFI specification for unsigned integers
matching the bitness of the CPU.
Types in U-Boot should be lower case. The patch replaces it
by efi_uintn_t.
Suggested-by: Simon Glass <sjg@chromium.org>
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
As we now have EFI_CALL there is no need for separate
functions efi_uninstall_protocol_interface_ext and
efi_uninstall_protocol_interface.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
As we now have EFI_CALL there is no need for separate
functions efi_install_protocol_interface_ext and
efi_install_protocol_interface.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This unit test checks the following protocol services:
InstallProtocolInterface, UninstallProtocolInterface,
InstallMultipleProtocolsInterfaces,
UninstallMultipleProtocolsInterfaces,
HandleProtocol, ProtocolsPerHandle,
LocateHandle, LocateHandleBuffer.
As UninstallProtocolInterface and UninstallMultipleProtocolsInterfaces
are not completely implemented a TODO message will shown for
their failure.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Constants should be capitalized.
So rename the values of enum efi_locate_search_type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The parent_handle of the loaded image must be set.
Set the system table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The following services are tested:
OutputString, TestString, SetAttribute.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Clear environment variable efi_selftest before executing the
default tests.
Provide a test verifying that the EFI watchdog
reboots the system upon timeout.
The test depends on CONFIG_CMD_EFI_SELFTEST=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
A test is added that verifies that the watchdog timer actually
causes a reboot upon timeout. The test is only executed on
request using
setenv efi_selftest watchdog reboot
bootefi selftest
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use environment variable bootargs used as load options
for bootefi payloads.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
After executing bootefi selftest
* restore GD
* unlink the load image handle
* return 0 or 1 and not a truncated efi_status_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Environment variable efi_selftest is passed as load options
to the selftest application. It is used to select a single
test to be executed.
The load options are an UTF8 string. Yet I decided to keep
the name propertiy of the tests as char[] to reduce code
size.
Special value 'list' displays a list of all available tests.
Tests get an on_request property. If this property is set
the tests are only executed if explicitly requested.
The invocation of efi_selftest is changed to reflect that
bootefi selftest with efi_selftest = 'list' will call the
Exit bootservice.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Move duplicate code to the new function efi_st_do_tests.
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If the compared memory areas match the return value should be 0.
We should not use the unrelated constant EFI_ST_SUCCESS.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Currently we pass bootefi_device_path and bootefi_image_path as
device and image path without initializing them. They may carry
values from previous calls to bootefi.
With the patch the variables are initialized valid dummy values.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Where ulong or unsigned long are used to hold an EFI status
code we should consistenly use efi_status_t.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use a define to detect double inclusion of efi_loader.h.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide a conversion function from utf8 to utf16.
Add missing #include <linux/types.h> in include/charset.h.
Remove superfluous #include <common.h> in lib/charset.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The test verifies that resetting the watchdog timer ensures
that it is not called during the timeout period.
Testing that the watchdog timer actually executes a reset
would require a test outside the efi_selftest framework.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The watchdog is initialized with a 5 minute timeout period.
It can be reset by SetWatchdogTimer.
It is stopped by ExitBoottimeServices.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
To avoid a forward declaration move efi_search_obj before
all protocol services functions.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
On the RK3399-Q7, we want to trigger a full platform reset (so the
various software stacks supported don't have to deal with the same
complexities over and over again) in case that anything other than a
power-on reset occurred.
To do so, this defines the /config/sysreset-gpio property and has it
point to a GPIO that will perform a power-on reset of the entire
platform.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The reset circuitry in the RK3399 only resets 'almost all logic' when
a software reset is performed. To make our software maintenance
easier in the future, we want to have the option (controlled by a DTS
property) to force all reset causes other than a power-on reset to
trigger a power-on reset via a GPIO trigger.
This adds the necessary support to the rk3399-puma (i.e. RK3399-Q7)
board-support and the documentation for the new property
(sysreset-gpio) within the /config-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
USB1 is connected to the on-module USB 3.0 hub and power to the hub
(actually it's a reset signal, modeled as a fixed regulator, that will
be released) should be enabled only during the first probing of the
device to avoid the hub from entering its low-power mode (where it
tries to attach on a fixed interval, but we always miss the timeslot
when U-Boot has the controller listening).
This adds a 'tsd,usb-port-power' stringlist to enable the
infrastructure in the board-specific usb_hub_reset_devices to find and
control the fixed regulator associated with control of the USB hub.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
For some versions of the RK3399-Q7 (at least revisions v1.1 and v1.2
are affected), we need to turn on the power for the port connected to
the on-module USB hub only when the device is probed for the first
time to ensure that the hub does not enter a low-power mode (that
U-Boot's USB stack can't deal with).
Note that this is needed for U-Boot only, as Linux eventually manages
to attach the hub even when it has entered into its low-power state
(when the hub wakes up the next time) after a few seconds.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Even if the board-specific directory Makefile doesn't have any
targets, it still needs to exist.
This adds a minimal Makefile for the board/rockchip/evb_rk3128
directory and a evk-rk3128.c (as built-in.o needs to be built
for every directory that a Makefile gets run for).
Fixes: c7a6866 ("rockchip: rk3128: add evb-rk3128 support")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dts binding header for rk3128, files origin from kernel.
Series-Changes: 2
- fix i2c address
- add saradc and usb phy node
- emmc using fifo mode for there is no dma support in rk3128 emmc
- add some clock id in cru.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With some of the recent cleanups (e.g. moving the DRAM controller
drivers for Rockchip devices to drivers/ram/rockchip), the files
and paths listed in MAINTAINERS no longer covered what really is
looked after as part of the Rockchip port.
This commit updates the files/paths listed in MAINTAINERS for the
Rockchip port. I am certain, though, that this will have missed some
additional paths that should have been included...
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The order of members in struct hws_topology_map is cas_wl, cas_l. The
comments in the original db-88f6820-gp.c had this wrong and have been
copied to other Armada-385 based boards. Practically this hasn't made a
difference since all these boards set both cas_wl and cas_l to 0
(autodetect) but if there were ever a board that did need to set these
explicitly they would run into unexpected issued.
Update the comments to reflect the correct order of structure members.
Reported-by: Tobi Wulff <tobi.wulff@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_ENV_IS_IN_NAND has been removed in commit 2be296538e (Convert
CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig).
CONFIG_ENV_IS_IN_SPI_FLASH has been removed in commit 91c868fe7c
(Convert CONFIG_ENV_IS_IN_SPI_FLASH to Kconfig). The environment #ifdef
is now empty. Remove it.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Check if we are booting from NAND and let the bootrom
continue to load the rest of the bootloader
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
It's the first 8 bits of the bootrom error register that
contain the boot error/fallback error code. Let's check that
and continue to boot from UART.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
bbt_mirror_descr and bbt_main_descr is defined but not used
when compiling without CONFIG_SYS_NAND_USE_FLASH_BBT set.
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the inclusion of the libgcc math functions and
replaces them by functions coded in C, taken from the coreboot
project. This makes U-Boot building more independent from the toolchain
installed / available on the build system.
The code taken from coreboot is authored from Vadim Bendebury
<vbendeb@chromium.org> on 2014-11-28 and committed with commit
ID e63990ef [libpayload: provide basic 64bit division implementation]
(coreboot git repository located here [1]).
I modified the code so that its checkpatch clean without any
functional changes.
[1] git://github.com/coreboot/coreboot.git
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Currently X86 does not properly support distro defaults.
This patch is only a partial fix.
It provides the name of the bootloader EFI application
for the X86 architecture.
The architecture dependent file names are defined in the UEFI
specification.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This reverts commit 13c531e52a.
The error message with FIT style image mentioned in the above commit
only happens when booting using FIT image containing bzImage kernel
and without setup node (setup.bin). The current documentation for
x86 FIT support in doc/uImage.FIT/x86-fit-boot.txt mentions that
kernel's setup.bin file is required for building x86 FIT images.
The above commit breaks FIT images generated as described in the
documentation. Revert it to allow booting with images built in the
documented way.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
x86_vendor_name is defined as
static const char *const x86_vendor_name[]
So its elements should not be compared to 0.
Remove superfluous paranthesis.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
ROM has been made read-only in qemu recently (namely commit 208fa0e4:
"pc: make 'pc.rom' readonly when machine has PCI enabled"). So this
patch restores compatibility between U-Boot and qemu.
Signed-off-by: Anton Gerasimov <anton@advancedtelematic.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: mention qemu commit title in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Before this patch one could receive following errors when executing "fatls"
command on machine with cache enabled (ex i.MX6Q) :
=> fatls mmc 0:1
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Fixes: 09fa964bba ("fs/fat: Fix 'CACHE: Misaligned operation at range' warnings")
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
GCC 7.1 seems to be smart enough to track val through the various
static inline functions, but not smart enough to see that val will
always be initialised when no error is returned. This triggers
the following warning:
env/mmc.c: In function 'mmc_get_env_addr':
env/mmc.c:121:12: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
To make it easier for compiler to understand what is going on, let's
initialise val.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Building spl with CONFIG_OF_EMBED enabled results in an error message
on my board: "SPL image too big". This is because the fdtgrep build
step is only executed for CONFIG_OF_SEPARATE.
Fix this by moving the fdtgrep build step ('cmd_fdtgreo') from
scripts/Makefile.spl to dts/Makefile so that the reduced dtb is
available for all kinds of spl builds.
The resulting variable name for the embedded device tree blob changes,
too, which is why common.h and fdtdec.c have tiny changes.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In U-Boot, this device tree is compatible with both the Torpedo and
SOM-LV kits. Let's rename it in the device tree since the U-Boot code and
show a more generic OMAP3 name. The code auto detects between the two and
loads the proper DTB file for Linux. This would eliminate the SOM-LV showing
the name Torpedo during boot and hopefully eliminate some confusion.
Signed-off-by: Adam Ford <aford173@gmail.com>
It is unwise to first dereference a variable
and then to check if it was NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When copying the command line buffer the target array should
at least have the same size.
Cf. definition of console_buffer in common/cli_readline.c.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
use ALLOC_CACHE_ALIGN_BUFFER_PAD for mbr header allocation
in stack to fix alloc issue in is_gpt_valid()
this patch fix also issue for GPT partition handling
with blocksize != 512 in set_protective_mbr()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The capabilities have default values which doesn't reflect the reality
when it concerns the base clock and the mul value. Use a fixe rate
for the gck. 240 MHz is an arbitrary choice, it is a multiple of the
maximum SD clock frequency handle by the controller and it allows to
get a 400 kHz clock for the card initialisation.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Differentiate the generic clock source selection value from the parent
clock index to fix the incorrect assignment of the generic clock
source selection.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To get the same behavior as the Linux driver, instead of selecting
the closest inferior rate, select the closest inferior or superior
rate
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
What the AT91_UTMI depends on SPL_DM isn't right. AT91_UTMI is not
only used in SPL, also in other place, even if SPL_DM isn't enabled.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
MPU's region setup can be factorized between STM32F4/F7/H7 SoCs family
and used a common MPU's region config.
Only one exception for STM32H7 which doesn't have device area
located at 0xA000 0000.
For STM32F4, configure_clocks() need to be moved from arch_cpu_init()
to board_early_init_f().
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
In order to factorize code between STM32F4 and STM32F7
migrate all structs related to RCC clocks in include/stm32_rcc.h
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
MMC block needs 48Mhz source clock, for that we choose
to select the SAI PLL.
Update also stm32_clock_get_rate() to retrieve the MMC
clock source needed in MMC driver.
STM32F4 uses a different RCC variant than STM32F7. For STM32F4
sdmmc clocks bit are located into dckcfgr register whereas there
are located into dckcfgr2 registers on STM32F7.
In both registers, bits CK48MSEL and SDMMC1SEL are located at
the same position.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This allows to add rcc MFD support to stm32f746-disco board
This rcc MFD driver manages clock and reset for STM32 SoCs family
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 doesn't get rcc.h file, to avoid compilation
issue, migrate RCC related defines from rcc.h to driver
file and remove rcc.h file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Now that clk_stm32f7.c manages clocks for both STM32F4 and F7 SoCs
rename it to a more generic clk_stm32f.c
Fix also some checkpatch errors/warnings.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
STM32F4 and STM32F7 RCC clock IP are very similar.
Same driver can be used to managed RCC clock for
these 2 SoCs.
Differences between STM32F4 and F7 will be managed using
different compatible string :
_ overdrive clock is only supported by STM32F7
_ different sys_pll_psc parameters can be used between STM32F4
and STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Align the RCC compatible string with the one used by kernel.
It will allow to use the same clock driver for STM32F4
and STM32F7 and to manage the differences between the 2 SoCs
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Add a dedicated stm32f7 compatible string to use clk_stm32f7
driver with both STM32F4 and STM32F7 SoCs.
It will be needed to manage differences between these 2 SoCs.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
PWR IP is used to enable over-drive feature in
order to reach a higher frequency.
Get its base address from DT instead of hard-coded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
This node is needed to enable performance mode
when system frequency is set up to 200Mhz.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Up to now we were able to read/write environment data from/to UBI
volumes only indirectly by gluebi driver. This driver creates NAND MTD
on top of UBI volumes, which is quite a workaroung for this use case.
Add support for direct read/write UBI volumes in order to not use
obsolete gluebi driver.
Forward-ported from this patch:
http://patchwork.ozlabs.org/patch/619305/
Original patch:
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Forward port:
Signed-off-by: S. Lockwood-Childs <sjl@vctlabs.com>
atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.
Signed-off-by: Rick Chen <rick@andestech.com>
ATCPIT100 is often used in AE3XX platform which is
based on NDS32 architecture recently. But in the future
Andestech will have AE250 platform which is embeded
ATCPIT100 timer based on RISCV architecture.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It will be work fine with unsigned long declaretion in timer
register struct when system is 32 bit. But it will not work
well when system is 64 bit. Replace it by u32 and verify both
ok in 32/64 bit.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When requesting a GPIO, set the PFC GPSR register to GPIO mode,
otherwise the GPIO cannot work.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add hook into the PFC driver to allow the GPIO driver to toggle
GPSR registers into GPIO mode when GPIO is requested.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to handle single pins nodes from DT in addition to already
support groups handling.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Stop using the old ad-hoc SH I2C driver and use the new RCar IIC
driver instead. The SH I2C driver should be deprecated and removed
eventually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Mark the PRR as u-boot,dm-pre-reloc in all Gen3 board DTs as it is
needed very early and turn on the CONFIG_SYSCON to allow the PRR
driver to bind as a syscon uclass.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Implement DM driver for the Renesas PRR into RCar cpu info and convert
all users with DM and OF enabled to this new driver. This means all of
the boards with DM and OF enabled can fetch PRR address from DT, which
is useful on ie. V3M which has different PRR address than the rest of
Gen3 SoCs.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As we have a proper clock framework driver, these macros are not
needed, so drop them and clean up the whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These macros are no longer needed since the DRAM configuration is parsed
from the DT. Drop them all.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the ad-hoc DRAM configuration with macros and just decode
the DRAM configuration from device tree instead. This makes it
far cleaner and easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since checkboard() is gone, rmobile_sysinfo is also pointless on Gen3.
Furthermore, nuke ad-hoc CONFIG_RCAR_BOARD_STRING which is also dead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The checkboard() function showing hard-coded board model for which the
U-Boot was built is superseded on Gen3 by show_board_info() displaying
the Model from device tree. Add small ifdef to stop compiling the
function into U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can now use rmobile_get_cpu_type() to check the CPU ID rather
than using a macro, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since both R8A7795 and R8A7796 now use the same files, unify the
Makefile entry to CONFIG_RCAR_GEN3.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Unify the R7A7795 and R8A7796 memory maps in memmap-gen3 and, for now,
select which one is used based on which SoC is selected. Since this is
done in C code instead of statically assigned now, the decision can be
taken by PRR SoC match as well, which will be done in a subsequent patch.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Replace the ad-hoc values in the PRR CPU ID table with macros,
so that users can use rmobile_get_cpu_type() can compare the
returned value with these macros to figure out on which CPU they
are running.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the Gen3 clock driver now has a .remove callback, it is no
longer necessary to shut the clock down before booting Linux in the
arch_preboot_os hook. Stop using it and while doing so, remove all
the ad-hoc config options which this hook used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
These old PFC tables are no longer needed as there is now a proper
PFC pinmux driver in drivers/pinctrl/renesas . Remove them .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull out the GIC macros from the board configuration files
into the common Gen3 configuration file since these macros
are the same for all Gen3 systems.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This command is useless on Salvator-X as it is reading DRAM info from
SPD. We have no SPD on Salvator-X.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the RCar Gen3 no longer uses the SH SDHI driver, but rather
uses the Matsushita SD driver, which loads all the properties from
device tree, these macros are no longer used, remove them.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the Micrel KSZ90x1 driver on ULCB, since the board is populated
with KSZ9031 and without this driver, the PHY cannot be operated.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for ULCB to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Fix handling of the reset GPIO. Drop the _nodev() suffix from the
gpio_request_by_name() call as there is now a proper DM capable
GPIO driver. Also check if the GPIO is valid before freeing it in
remove path, otherwise U-Boot will crash.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add driver for the RCar IIC or DVFS I2C controller. This driver is based
on the SH I2C driver, but supports DM and DT probing as well as modern
I2C framework API.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Unify the CONFIG_R8A7795 and CONFIG_R8A7796 as CONFIG_RCAR_GEN3
so that every time we add a new SoC, we won't have to add more
stuff to this list.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add xHCI entry into the clock tables, so that the xHCI USB driver
can enable the clock for the xHCI block via clock framework.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The MSTP registers were poked in boards/renesas/rcar-common/common.c
in arch_preboot_os hook thus far to shut down the clock before Linux
takes over. With DM, this is no longer needed and we can do the same
in the clock driver .remove callback. This patch adds such a .remove
callback for R8A7795 and R8A7796.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It is legal to have multiple /memory nodes in a device tree . Currently,
fdtdec_setup_memory_size() only supports parsing the first node . This
patch extends the function such that if a particular /memory node does
no longer have further "reg" entries and CONFIG_NR_DRAM_BANKS still
allows for more DRAM banks, the code moves on to the next memory node
and checks it's "reg"s. This makes it possible to handle both systems
with single memory node with multiple entries and systems with multiple
memory nodes with single entry.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
To help out with the RCar/RMobile upstreaming, I'm adding myself
as the RCar/RMobile maintainer.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Xilinx changes for v2018.1
Zynq:
- Add support for Syzygy and cc108 boards
- Add support for mini u-boot configurations (cse)
- dts updates
- config/defconfig updates in connection to Kconfig changes
- Fix psu_init handling
ZynqMP:
- SPL fixes
- Remove slcr.c
- Fixing r5 startup sequence
- Add support for external pmufw
- Add support for new ZynqMP chips
- dts updates
- Add support for zcu102 rev1.0 board
Drivers:
- nand: Support external timing setting and board init
- ahci: Fix wording
- axi_emac: Wait for bit, non processor mode, readl/write conversion
- zynq_gem: Fix SGMII/PCS support
This patch uses readl and writel instead of in_be32 and
out_be32 for io ops as these internally uses readl,
writel for microblaze and for Zynq, ZynqMP there is
no need of endianness conversion and readl, writel
should work straightaway. This patch starts supporting
the driver for Zynq and ZynqMP platforms.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont enable SGMII and PCS selection if internal PCS/PMA
is not used, by getting the info about internal/external
PCS/PMA usage from dt property "is-internal-phy".
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use more accurate description for Xilinx Zynq and ZynqMP based platforms.
With using driver model there shouldn't be a need to create separate
Kconfig config options.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The chapter in which the table explaining the image format changed
chapter as the document evolved. This should help people track the
info down faster.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Sparse is return warning about this:
arch/arm/mach-zynq/slcr.c: In function 'zynq_slcr_get_mio_pin_status':
arch/arm/mach-zynq/slcr.c:185:16: warning: comparison between signed and
unsigned integer expressions [-Wsign-compare]
for (i = 0; i < ARRAY_SIZE(mio_periphs); i++) {
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add proper support for EMIT_WRITE operation which is write only.
Do not use EMIT_MASKWRITE which is read-modify-write.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is based on work done in topic board where the first address
word also storing operation which should be done. This is reducing size
of configuration data.
This patch is not breaking an option to copy default ps7_init_gpl* files
from hdf file but it is doing preparation for ps7_init* consolidation.
The patch is also marking ps7_config as weak function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add missing declaration to header.
Warning log:
arch/arm/mach-zynq/spl.c:94:12: warning: symbol 'ps7_post_config' was
not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for non processor mode, this mode doesn't have
access to some of the registers and hence this patch
bypasses it and also length has to be calculated from
status instead of app4 in this mode.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
U-Boot is generally flashed to a MIPS Boston development board by means
of a .mcs file which Xilinx Vivado software can write to the flash
present on the board. As such we'd generally want to produce an mcs file
when building U-Boot to target the Boston board. Introduce a make target
for u-boot.mcs which generates it using the srec_cat tool available from
the SRecord project, and build it by default when srec_cat is present.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
Generally we load Linux kernels on Boston boards in the form of FIT
images containing a compressed kernel binary. Linux is linked at
0x80100000 and so we need to decompress the kernel binary to that
address, however this is our default load address which means that
unless explicitly avoided we hit a decompression error as the
uncompressed kernel binary overwrites its compressed version from the
FIT image.
Avoid this by adjusting CONFIG_SYS_LOAD_ADDR to 0x88000000 (or
0xffffffff88000000 for MIPS64 builds) which avoids the address overlap
between compressed & uncompressed kernel binaries.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
If we run on a CPU which doesn't implement a particular cache then we
would previously get stuck in an infinite loop, executing a cache op on
the first "line" of the missing cache & then incrementing the address by
0. This was being avoided for the L2 caches, but not for the L1s. Fix
this by generalising the check for a zero line size & avoiding the cache
op loop when this is the case.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
When writing code, for example during relocation, we ensure that the
icache has a coherent view of the new instructions with a call to
flush_cache(). This handles the bulk of the work to ensure the new
instructions will execute as expected, however it does not ensure that
the CPU pipeline doesn't already contain instructions taken from a stale
view of the affected memory. This could theoretically be a problem for
relocation, but in practice typically isn't because we sync caches for
enough code after the entry point of the newly written code that by the
time the CPU pipeline might possibly fetch any of it we'll have long ago
written it back & invalidated any stale icache entries. This is however
a problem for shorter regions of code.
In preparation for later patches which write shorter segments of code,
ensure any instruction hazards are cleared by flush_cache() by
introducing & using a new instruction_hazard_barrier() function which
makes use of the jr.hb instruction to clear the hazard.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
A typical use of cache maintenance functions is to force writeback of
data which a device is about to read using DMA - for example a
descriptor or command structure. Such users of cache maintenance
functions require that operations on the cache have completed before
they proceed to instruct a device to read memory. This requires that we
place a completion barrier (ie. sync instruction) between the cache ops
and whatever write informs the device to perform DMA.
Whilst strictly speaking this isn't all users of the cache maintenance
functions & we could instead place the barriers in the drivers that
require them, it would be much more invasive to do so than to just have
the barrier be the default by placing it in the cache functions
themselves. The cost is low enough that it shouldn't matter to us in any
rare cases that we use the cache functions when not performing DMA.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
MIPS is no longer a part of Imagination Technologies, and as such my
@imgtec.com email address will soon cease to function. This patch
updates occurrances of it with my new @mips.com email address, and adds
an entry in .mailmap such that git (& tools such as get_maintainer.pl
when examining history) will use the new address.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: u-boot@lists.denx.de
The u-boot.lds linker script for MIPS defines a PTR_COUNT_SHIFT macro to
2 or 3 for 32 bit or 64 bit builds respectively. This macro is never
actually used though, so remove the dead code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The boston lowlevel_init() function zeroes the return register v0,
despite the function not being expected to return a value & that value
never being used.
Remove the redundant assignment to v0.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This work-around has been here in U-Boot because the AIDET and GPIO
drivers were missing in the upstream Linux. Both are now available
in Linus' tree:
- drivers/irqchip/irq-uniphier-aidet.c
- drivers/gpio/gpio-uniphier.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I largely reworked the Denali NAND controller driver in Linux.
This commit imports the improvements from Linux. The code is
almost synced with Linux 4.15-rc1.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Several drivers check ->chipsize to see if the third row address cycle
is needed. Instead of embedding magic sizes such as 32MB, 128MB in
drivers, introduce a new flag NAND_ROW_ADDR_3 for clean-up. Since
nand_scan_ident() knows well about the device, it can handle this
properly. The flag is set if the row address bit width is greater
than 16.
Delete comments such as "One more address cycle for ..." because
intention is now clear enough from the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 14157f861437ebe2d624b0a845b91bbdf8ca9a2d]
struct nand_ecc_caps was designed as flexible as possible to support
multiple stepsizes (like sunxi_nand.c).
So, we need to write multiple arrays even for the simplest case.
I guess many controllers support a single stepsize, so here is a
shorthand macro for the case.
It allows to describe like ...
NAND_ECC_CAPS_SINGLE(denali_pci_ecc_caps, denali_calc_ecc_bytes, 512, 8, 15);
... instead of
static const int denali_pci_ecc_strengths[] = {8, 15};
static const struct nand_ecc_step_info denali_pci_ecc_stepinfo = {
.stepsize = 512,
.strengths = denali_pci_ecc_strengths,
.nstrengths = ARRAY_SIZE(denali_pci_ecc_strengths),
};
static const struct nand_ecc_caps denali_pci_ecc_caps = {
.stepinfos = &denali_pci_ecc_stepinfo,
.nstepinfos = 1,
.calc_ecc_bytes = denali_calc_ecc_bytes,
};
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: a03c60178c181767ecfb26fb311a88742d228118]
Driver are responsible for setting up ECC parameters correctly.
Those include:
- Check if ECC parameters specified (usually by DT) are valid
- Meet the chip's ECC requirement
- Maximize ECC strength if NAND_ECC_MAXIMIZE flag is set
The logic can be generalized by factoring out common code.
This commit adds 3 helpers to the NAND framework:
nand_check_ecc_caps - Check if preset step_size and strength are valid
nand_match_ecc_req - Match the chip's requirement
nand_maximize_ecc - Maximize the ECC strength
To use the helpers above, a driver needs to provide:
- Data array of supported ECC step size and strength
- A hook that calculates ECC bytes from the combination of
step_size and strength.
By using those helpers, code duplication among drivers will be
reduced.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2c8f8afa7f92acb07641bf95b940d384ed1d0294]
Some NAND controllers can assign different NAND timings to different
CS lines. Pass the CS line information to ->setup_data_interface() so
that the NAND controller driver knows which CS line is concerned by
the setup_data_interface() request.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 104e442a67cfba4d0cc982384761befb917fb6a1]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 477544c62a84d3bacd9f90ba75ffc16c04d78071]
Drivers setting NAND_ECC_CUSTOM_PAGE_ACCESS are supposed to handle the
full read/write page sequence, and waiting for a page to actually be
programmed is part of this write-page sequence.
This is also what is done in ->write_oob_xxx() hooks, so let's do that in
->write_page_xxx() as well to make it consistent.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 41145649f4acb30249b636b945053db50c9331c5]
[masahiro:
There is no driver setting NAND_ECC_CUSTOM_PAGE_ACCESS in U-Boot.
No driver is affected by this change.]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The ->errstat() hook is no longer implemented NAND controller drivers.
Get rid of it before someone starts abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 7d135bcced20be2b50128432c5426a7278ec4f6d]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cached programming is always skipped, so drop the associated code until
we decide to really support it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 0b4773fd1649e0d418275557723a7ef54f769dc9]
[masahiro: modify davinci_nand.c for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to make the ecclayout definition completely dynamic we need to
rework the way the OOB layout are defined and iterated.
Create a few mtd_ooblayout_xxx() helpers to ease OOB bytes manipulation
and hide ecclayout internals to their users.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 75eb2cec251fda33c9bb716ecc372819abb9278a]
[masahiro:
cherry-pick more code from adbbc3bc827eb1f43a932d783f09ba55c8ec8379]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If your controller already sends the required NAND commands when
reading or writing a page, then the framework is not supposed to
send READ0 and SEQIN/PAGEPROG respectively.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 3371d663bb4579f1b2003a92162edd6d90edd089]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add the tR_max, tBERS_max, tPROG_max and tCCS_min timings to the
nand_sdr_timings struct.
Assign default/safe values for the statically defined timings, and
extract them from the ONFI parameter table if the NAND is ONFI
compliant.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 204e7ecd47e26cc12d9e8e8a7e7a2eeb9573f0ba
Fixup commit: 6d29231000bbe0fb9e4893a9c68151ffdd3b5469]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When changing from one data interface setting to another, one has to
ensure a specific sequence which is described in the ONFI spec.
One of these constraints is that the CE line has go high after a reset
before a command can be sent with the new data interface setting, which
is not guaranteed by the current implementation.
Rework the nand_reset() function and all the call sites to make sure the
CE line is asserted and released when required.
Also make sure to actually apply the new data interface setting on the
first die.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: d8e725dd8311 ("mtd: nand: automate NAND timings selection")
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
[Linux commit: 73f907fd5fa56b0066d199bdd7126bbd04f6cd7b]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The NAND framework provides several helpers to query timing modes supported
by a NAND chip, but this implies that all NAND controller drivers have
to implement the same timings selection dance. Also currently NAND
devices can be resetted at arbitrary places which also resets the timing
for ONFI chips to timing mode 0.
Provide a common logic to select the best timings based on ONFI or
->onfi_timing_mode_default information. Hook this into nand_reset()
to make sure the new timing is applied each time during a reset.
NAND controller willing to support timings adjustment should just
implement the ->setup_data_interface() method.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[Linux commit: d8e725dd831186a3595036b2b1df9f68cbc6efa3]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
struct nand_data_interface is the designated type to pass to
the NAND drivers to configure the timing. To simplify further
patches convert the onfi_sdr_timings array from type struct
nand_sdr_timings nand_data_interface.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: b1dd3ca203fccd111926c3f6ac59bf903ec62b05]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently we have no data structure to fully describe a NAND timing.
We only have struct nand_sdr_timings for NAND timings in SDR mode,
but nothing for DDR mode and also no container to store both types
of timing.
This patch adds struct nand_data_interface which stores the timing
type and a union of different timings. This can be used to pass to
drivers in order to configure the timing.
Add kerneldoc for struct nand_sdr_timings while touching it anyway.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: eee64b700e26b9bcc6fce024681c31f5e12271fc]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When NAND devices are resetted some initialization may have to be done,
like for example they have to be configured for the timing mode that
shall be used. To get a common place where this initialization can be
implemented create a nand_reset() function. This currently only issues
a NAND_CMD_RESET to the NAND device. The places issuing this command
manually are replaced with a call to nand_reset().
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 2f94abfe35b210e7711af9202a3dcfc9e779219a]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
'extern' is not necessary for function declarations. To prevent
people from adding the keyword to new declarations remove the
existing ones.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[Linux commit: 79022591839f110f465cac0223e117b91d47d5db]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The generic NAND DT bindings allows one to tweak the ECC strength and
step size to their need. It can be used to lower the ECC strength to
match a bootloader/firmware config, but might also be used to get a better
reliability.
In the latter case, the user might want to use the maximum ECC strength
without having to explicitly calculate the exact value (this value not
only depends on the OOB size, but also on the NAND controller, and can
be tricky to extract).
Add a generic 'nand-ecc-maximize' DT property and the associated
NAND_ECC_MAXIMIZE flag, to let ECC controller drivers select the best
ECC strength and step-size on their own.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[Linux commit: ba78ee00e1ff84de9b3ad33edbd3ec599099ee82]
[masahiro: of_property_read_bool -> fdt_getprop for U-Boot]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add stubs to the header in case CONFIG_SYS_NAND_ONFI_DETECTION is
disabled. This is much easier than adding around #ifdef to the
caller side.
Also, I removed the #ifdef around onfi_params. In Linux, onfi_params
and jedec_params are unified as union. It will be the right thing
to do.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These boards are on the boundary of "u-boot-nodtb.bin exceeds file
size limit" error.
Reduce the log-level to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read dma address using fdtdec_get_addr as it checks for
address cells and size cells and reads the address
properly. fdtdec_get_int always assume address is of int
size which goes wrong if using it on 64-bit architecture.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes SMMU work by moving the iommus node under the dwc3 child
entry from parent node.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch uncomments snps,quirk-frame-length-adjustment which has
the value to adjust the SOF/ITP generated from the controller.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds OTG interrupt support in device tree. It will add
an extra interrupt line number dedicated to OTG events. This will
enable OTG interrupts to serve in DWC3 OTG driver.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds CCI support for USB when CCI is enabled in design.
This patch also adds 'reg' property for Xilinx USB 3.0 IP. The 'reg'
property is added in order to modify a register in that to enable
coherency in Hardware.
Also add address to unit name to avoid dtc warning
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for reading silicon revision using zynqmp nvmem
driver.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The AMS includes an ADC as well as on-chip sensors that can be used to
sample external voltages and monitor on-die operating conditions, such as
temperature and supply voltage levels.
Signed-off-by: Rajnikant Bhojani <rajnikant.bhojani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch sets host quirk2 bit field for No 1.8V supported in case of
1.0 silicon. The 1.0 silicon doesn't have support for UHS-I modes. This
property will ensure the SD runs on High Speed mode.
Signed-off-by: Manish Narani <mnarani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the phy_zynqmp.c driver to use reset-controller
framework for asserting/de-asserting reset for High Speed modules.
Also fix documentation and dtsi.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add the reset nodes in zynqmp.dtsi which are used by
reset-controller framework
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Only silicon v1 requires this termination fix. With new nvmem soc
revision nvmem detection driver this can be autodetected at run time and
this flag is not needed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Generic dtsi file can't use the same mac address for all.
U-Boot read mac from eeprom in zcu102 case and for others random mac
address is generated.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
dtc reports issues with it.
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-zc1751-xm016-dc2.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff040000/spi0_flash0@0/spi0_flash0@00000000 unit name should
not have leading 0s
arch/arm64/boot/dts/xilinx/zynqmp-ep108.dtb: Warning
(unit_address_format): Node
/amba/spi@ff050000/spi1_flash0@0/spi1_flash0@00000000 unit name should
not have leading 0s
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Some user space libraries reading platform compatible string and based
on that changing behavior. Mark revB board with revB string.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently DP power domain (pd_dp) is not attached to any of the DP nodes which is
causing genpd to trigger a power down request for DP domain, making all DP related
peripherals unusable. So assign power domains for all DP related nodes to enable
proper accounting of DP power domain usage.
Signed-off-by: Jyotheeswar Reddy <jyothee@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch disables the smmu and also removes the mmu-masters
Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds the calibration property with required value,
calculated based on rtc input crystal oscillator frequency (32.768Khz).
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
AXI master interface in CEVA AHCI controller requires two unique
Write/Read ID tags per port. This is because, ahci controller uses
different AXI ID[3:0] bits for identifying non-data transfers(like
reading descriptors, updating PRD tables, etc) and data transfers
(like sending/receiving FIS).To make SMMU work with SATA we need to
add correct SMMU stream id for SATA. SMMU stream id for SATA is
determined based on the AXI ID[1:0] as shown below
SATA SMMU ID = <TBU number>, 0011, 00, 00, AXI ID[1:0]
Note: SATA in ZynqMp uses TBU1 so TBU number = 0x1, so
SMMU ID = 001, 0011, 00, 00, AXI ID[1:0]
Since we have four different AXI ID[3:0] (2 for port0 & 2 for port1
as said above) we get four different SMMU stream id's combinations
for SATA. These AXI ID can be configured using PAXIC register.
In this patch we assumed the below AXI ID values
Read ID/ Write ID for Non-Data Port0 transfers = 0
Read ID/ Write ID for Data Port0 transfers = 1
Read ID/ Write ID for Non-Data Port1 transfers = 2
Read ID/ Write ID for Data Port1 transfers = 3
Based on the above values,SMMU stream ID's for SATA will be 0x4c0 &
0x4c1 for PORT0, 0x4c2 & 0x4c3 for PORT1. These values needed to be
added to iommus dts property. This patch does the same.
Signed-off-by: Anurag Kumar Vulisha <anuragku@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
All gpio controllers should contain this property.
This property is not checked by the code that's why this issue wasn't
found earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The correct register size is 0x10000, otherwise
it overlaps with other register space.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This will simplify dt overlay structure for the whole PL.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extract from Linux mainline patch:
The ARM architected timer specification mandates that the interrupt
associated with each timer is level triggered (which corresponds to
the "counter >= comparator" condition).
A number of DTs are being remarkably creative, declaring the interrupt
to be edge triggered. A quick look at the TRM for the corresponding ARM
CPUs clearly shows that this is wrong, and I've corrected those.
For non-ARM designs (and in the absence of a publicly available TRM),
I've made them active low as well, which can't be completely wrong
as the GIC cannot disinguish between level low and level high.
The respective maintainers are of course welcome to prove me wrong.
While I was at it, I took the liberty to fix a couple of related issue,
such as some spurious affinity bits on ThunderX, and their complete
absence on ls1043a (both of which seem to be related to copy-pasting
from other DTs).
Acked-by: Duc Dang <dhdang@apm.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
PM callbacks are delivered to the NS OS. Let the PM driver handle the
IRQ and retrieve callback data from the secure HW.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Changed min-residence to 10ms(was 100 ms) for cpu-sleep-0.
Tried lower values 5ms and 8ms and it worked fine with Debug Off.
But to accommodate PM Debug On case, 10 ms is required. With this
change, low power idle state is into effect more frequently.
Measured boot time with PM debugs On and Off. No change observed
compared to 100ms value.
Signed-off-by: Jolly Shah <jollys@xilinx.com>
Acked-by: Will Wong <willw@xilinx.com>
Tested-by: Koteswararao Nayudu <kotin@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Version string has unused fields 31:20 which can be used for exporting 9
bits from efuse IPDISABLE regs to recognize eg/cg/ev devices.
These efuse bits are setup for certain devices.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This modifies default value of config DEFINE_TCM_OCM_MMAP
to yes if CONFIG_MP is defined MP supports needs OCM and TCM
part of memory map.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch is adding external pmufw "Platform Management Unit firmware"
to boot.bin image. Boot.bin is a Xilinx format which bootrom is capable
to read and boot the system. pmufw is copied to the header data section
follows by u-boot-spl.bin. pmufw is consumed by PMU unit (Microblaze)
and SPL runs on a53-0.
This is generated command line when PMUFW_INIT_FILE is setup.
./tools/mkimage -T zynqmpimage -R ./"" -n
./"board/xilinx/zynqmp/pmufw.bin" -d spl/u-boot-spl.bin spl/boot.bin
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch provides a Kconfig option to use specified
memory for MMU table using reserve_mmu platform specific
routine. Here we used TCM space for MMU table.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrects the R5 release sequence by adding the
below steps.
1. Flush dcache to ensure that image loaded into memory.
2. Keep R5 reset just to ensure R5 in reset.
3. Disable caches before accessing TCM as with out this
A53 can do speculative and may result in ECC failures
if TCM's are not initialized. So, it is always better
to disable dcaches before accessing TCM and enable back.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reported-by: John Linn <linnj@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configurations which runs
out of OCM.
ram top is calculated from 0 that's why +#define CONFIG_SYS_SDRAM_BASE
0xfffc0000
+#define CONFIG_SYS_SDRAM_SIZE 0x40000
was hardcoded.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cc108 board is wiring uart via PL which is good platform for SPL fpga
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
All these configs were moved to Kconfig that's why this empty ifdef
structure is not needed anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Mention device-type = "ethernet-phy", as qemu will need this in absence
of compatible.
Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In legacy method, 1st stage bootloader was used to configure the HW
setting such as NAND timing. Hence, adding a config option in Zynq
NAND driver for the compatibility of device that using 1st stage
bootloder instead of U-boot SPL.
This commit is to add config option
CONFIG_NAND_ZYNQ_USE_BOOTLOADER1_TIMINGS that allow NAND driver use
timing values set by the 1st stage bootloader, instead of the hard-coded
values in the Zynq NAND driver.
Signed-off-by: Jeff Westfahl <jeff.westfahl@ni.com>
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Scott Wood <oss@buserror.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In
if (a || b)
else if (!a)
the constraint (!a) is always true if else is reached and
can be removed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This option prevents booting on am335x_evm at least along with most
likely other platforms.
Fixes: 337bbb6297 ("spl: fit: add SPL_FIT_IMAGE_TINY config to reduce code-size")
Signed-off-by: Tom Rini <trini@konsulko.com>
While the USB HW in the RZ/A is basically the same, there are some
differences from the original versions that were in the SH SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
icorem6 has sd on usdhci1 which is devno 0 so return proper
devno from board_mmc_get_env_dev for icorem6 and icorem_6rqs
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add new board names for existing board support
imx6q - icore and icore_rqs boards
imx6ul - geam6ul and isiot boards
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
As per USDHC boot eFUSE descriptions:
USDHC3 => devno 2
USDHC4 => devno 3
Linux will detect mmc0, mmc1, mmc2 based on the status
"okay" on usdhc so imx6qdl-icore-rqs.dtsi has enabled
usdhc1, usdhc3 and usdhc4.But U-Boot can detect based
on the aliases so add mmc1, mmc2 for usdhc3 and usdhc4
respectively and return the board_mmc_get_env_dev
by subtracting -1
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
before relocation pinctrl data BSS is overlapping DT area,
when .data is using uninitialized global variable,
imx6_pinctrl_soc_info. So assign them flags ZERO_OFFSET_VALID
to prevent BSS overlap
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
mx6sxsabresd can run different kernel versions, such as NXP 4.1 or mainline.
Currently the rootfs location is passed via mmcblk number and the
problem with this approach is that the mmcblk number for the SD
card changes depending on the kernel version.
In order to avoid such issue, use the UUID method to specify the
rootfs location.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
imx_set_wdog_powerdown() is always used to disable the power down
enable bit, so remove the boolean parameter of the function.
It is also a bit strange to write a boolean value into registers,
so this new version makes explicit that we are writing 0.
While at it, rename it to imx_wdog_disable_powerdown().
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Clear powerdown enable bit for WDOG3 on i.MX6ULL to avoid unwanted
kernel reboots.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
i.MX6ULL has the same WDOG3 base address as i.MX6UL, so take this
into account in the base address definition.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The boot (and fallback/emergency boot) concept for the RK3399-Q7
differs from Rockchip's reference platforms.
On the RK3399-Q7, some of this functionality is present in the
bootloader itself (and configurable); some is backed in hardware by
the Qseven BIOS_DISABLE signal to invoke the final stages of fallbacks
(i.e. either an external boot bypassing on-module memories or falling
back to the BROM for USB recovery).
In summary: the ADC-based boot_mode check does not apply for the
RK3399-Q7 and we therefore disable it (in this commit) by setting
CONFIG_BOOT_MODE_REG to 0.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The ROCKCHIP_BOOT_MODE_REG option defaults to a hex value, so 0 will
show as 0x0 if a default is provided and changed via Kconfig.
However, it still will show as 0, if no default is given.
Consequently, the "is set to something other than 0" test in a
Makefile is cumbersome. Instead this check can easily be performed in
the C-code.
This removes the ifeq-check from mach-rockchip/Makefile, adds a
matching #if-check to boot_mode.c and fixes resulting link issues (if
boot_mode.o was not included due to the Makefile check) by defining a
stub function (in case the functionality is not built in) for
setup_boot_mode in boot_mode.c.
Fixes: e306779 (rockchip: make boot_mode related codes reused across all platforms)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Existing FPGA program write is always assume RBF data >= 32 bytes, so
any rbf data less than 32 bytes writing to FPGA would be failed.
This patch enhances the FPGA program write to support rbf data with
size >= 4 bytes.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
This DT binding doc is porting from Linux DT binding doc.
commit 1adcbea4201a6852362aa5ece573f1f169b28113
Add a device tree bindings document for the SoCFPGA Arria10
FPGA Manager driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Increase the buffer length to be just above maximum permissible value
of 128 kiB . This increases the performance of the UMS and alike by a
factor of 2 - 2.5 as the buffers are less fragmented.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <lukma@denx.de>
When usb_hub_reset_devices is called, it should be passed both an
indicator which hub it should operate on and what port number (local
to that hub) should be reset.
Previously, the usb_hub.c code did not include such context and
always started resets from port number 1, performing multiple
reset-requests for the same devices:
/*
* Reset any devices that may be in a bad state when applying
* the power. This is a __weak function. Resetting of the devices
* should occur in the board file of the device.
*/
for (i = 0; i < dev->maxchild; i++)
usb_hub_reset_devices(i + 1);
This adds an additional 'hub' parameter to usb_hub_reset_devices
that provides the context to fully qualify the port-number in.
Existing implementations are changed to accept and ignore the new
parameter.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Its a valid use case to call ehci_submit_async() with a NULL buffer
with length 0. E.g. from usb_set_configuration().
As invalidate_dcache_range() isn't able to judge if the address
NULL is valid or not (depending on the SoC hardware configuration it
might be valid) do the check in ehci_submit_async() as here we know
that we don't have to invalidate such a buffer.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Currently we check in ehci_shutdown() if ctrl is NULL after
dereferencing it.
Before this we have already dereferenced ctrl, ctrl->hccr,
and ctrl->hcor in ehci_get_portsc_register(), ehci_submit_root(),
and hci_common_init().
A better approach is to already check ctrl, ctrl->hccr, and ctrl->hcor
during the initialization in ehci_register() and usb_lowlevel_init()
and signal an error here via the return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car
Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+
and R8A7796 are supported.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Commit 9000eddbae ("drivers/usb/ehci: Use platform-specific accessors")
broke USB 2.0 on big-endian platforms because for them writel/readl()
does automatic conversion of BE data to LE.
Proper implementation requires to use "raw" variant of these accessors
which read/write data without messing with endianess.
While at it replace cpu_to_be32() to be32_to_cpu() in readl() to
keep sane semantics.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Reported-by: Vladimir Boroda <boroda@yahoo.com>
Usb tree/info commands iterate over all usb uclass devices recursively.
Blk uclass devices based on struct blk_desc are created for mass storage
device, treating them as usb uclass devices based on struct usb_device
and referencing usb config interface descriptors cause crash.
To fix, ignore blk and usb_emul uclass devices in usb_show_info
and usb_tree_graph. Also avoid addition of preamble for blk uclass
child devices, otherwise tree dump gets messed up.
Signed-off-by: Suneel Garapati <suneelglinux@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399 has a total of 9 I2C controllers. To support these, the
enum in periph.h is extended and the mapping from the IRQ numbers to
the peripheral-ids is extended to ensure that pinctrl requests are
passed through to the function configuring the I2C pins.
For I2C8, the pinctrl is implemented and tested (on a RK3399-Q7) using
communication with the FAN53555 connected on I2C8.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The RK3399 clk driver still has a left-over use of extract_bits, which
can be replaced by using bitfield_extract from include/bitfield.h.
This rewrites the invocation to use the shared function.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A minor code-size increase from the changes for tracking the os-type
of FIT images and from infrastructure for recording the loadables into
the the loaded FDT, broke the builds for sun50i and some OMAP2+ devices.
This change adds a new config option (enabled by default for
MACH_SUN50I, MACH_SUN50I_H5 and ARCH_OMAP2PLUS) that does skips these
processing steps (bringing code size down to below the limit
again). The os-type is not evaluated, but assumed to be IH_OS_UBOOT
(i.e. taking the code-paths intended for backward-compatibility).
Note that enabling this config option precludes any useful downstream
processing, such as utilising a special calling convention for ATF or
OPTEE, based on the os-type of the loadables.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This tracks the SPL changes for ATF for the RK3368-uQ7:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE (now dynamically retrieved from
the .itb file)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This defconfig update makes use of the new features:
* CONFIG_ROCKCHIP_SPL_RESERVE_IRAM is now set to 0, as there is no
overlap between the M0 firmware and the ATF (we load this to DRAM
and relocate it to its final location within the ATF)
* tracks the ATF_SUPPORT -> ATF renaming
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the RK3368-uQ7, we can now update the .its file to mark the
Trusted Firmware as out 'firmware' bootable and annotate both ATF and
U-Boot with an OS-type.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit updates the .its file for the RK3399-Q7 to use the new
features and demonstrates how to use those:
* it marks the ATF as the 'firmware'
* it tracks the OS-type for U-Boot and ATF
* it loads the PMU (M0) firmware to DRAM and records the location
to /fit-images (where our ATF reads it from)
With the handoff of the next-stage FDT to ATF in place, we can now use
this to pass information about the load addresses and names of each
loadables to ATF: now we can load the M0 firmware into DRAM and avoid
overwriting parts of the SPL stage. This is achieved by changing our
.its-file to use an available area of DRAM as the load-address.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This tracks the SPL changes for ATF for the Firefly:
* renames ATF_SUPPORT to ATF
* drops CONFIG_SPL_ATF_TEXT_BASE
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having CONFIG_SPL_ATF seems more natural.
Rename it, while it it is easy and there's few boards that use it
(only RK3399 and RK3368 boards).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a new interface spl_invoke_atf() that takes a spl_image_info
argument and then derives the necessary parameters for the ATF entry.
Based on the additional information recorded (into /fit-images) from
the FIT loadables, we can now easily locate the next boot stage.
We now pass a pointer to a FDT as the platform-specific parameter
pointer to ATF (so we don't run into the future headache of every
board/platform defining their own proprietary tag-structure), as
FDT access is already available in ATF.
With the necessary infrastructure in place, we can now update the
support for the ARM Trusted Firmware to dispatch into the
spl_invoke_atf function only if a IH_OS_ARM_TRUSTED_FIRMWARE image is
loaded.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If a FDT was loaded (e.g. to append it to U-Boot image), we store it's
address and record information for all loadables into this FDT. This
allows us to easily keep track of images for multiple privilege levels
(e.g. with ATF) or of firmware images preloaded into temporary
locations (e.g. PMU firmware that may overlap the SPL stage).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
During the loading of more complex FIT images (e.g. when the invoked
next stage needs to find additional firmware for a power-management
core... or if there are multiple images for different privilege levels
started in parallel), it is helpful to create a record of what images
are loaded where: if a FDT is loaded for one of the next stages, it
can be used to convey the status and location of loadables.
This adds a fdt_record_loadable() function that can be invoked to
record the status of each loadable below the /fit-images path.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To better support bootin through an ATF or OPTEE, we need to
streamline some of the logic for when the FDT is appended to an image:
depending on the image type, we'd like to append the FDT not at all
(the case for the OS boot), to the 'firmware' image (if it is a
U-Boot) or to one of the loadables (if the 'firmware' is an ATF, an
OPTEE, or some other image-type and U-Boot is listed in the
loadabled).
To achieve this goal, we drop the os_boot flag and track the type of
image loaded. If it is of type IH_OS_U_BOOT, we append the FDT.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mainly a stylistic change: convert the load_addr and entry_point
fields of struct spl_image_info to uintptr_t (from ulong).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When loading a full U-Boot with detached device-tree using the SPL FIT
backend, we should store the address of the FDT loaded as part of the
SPL image info: this allows us to fixup the FDT with additional info
we may want to propagate onward.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To boot on ARMv8 systems with ARM Trusted Firmware, we need to
assemble an ATF-specific parameter structure and also provide the
address of the images started by ATF (e.g. BL3-3, which may be the
full U-Boot).
To allow us to identify an ARM Trusted Firmware contained in a FIT
image, this adds the necessary definitions.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As per ARC HS databook (see chapter 5.3.3.2) it is required to add
3 NOPs after each write to IC_IVIC which we do from now on.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
Currently slave cores will be kick-started even if we want
to dry run bootm which is not what we really want.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Eugeniy Paltsev <paltsev@synopsys.com>
MRC (Memory Reference Code) is a binary blob used to set up the SDRAM
controller on some Intel boards. Add a test for this feature.
With this test coverage on binman is back up to 100%.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test for this feature. It allows SPL to hold a pointer to the
microcode block. This is used for 64-bit U-Boot on x86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a main program so that the tests can be executed directly, without
going through the main binman program.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a test that the 'entry' module works with or without importlib.
The tests are numbered so that they are executed in the correct order.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a little check at the top of entry.py which decides if importlib
is available. At present this has no test coverage. To add this we will
need to import the module twice, once with importlib and once without.
In preparation for allowing a test to control the importing of this
module, remove all global imports of the 'entry' module.
Signed-off-by: Simon Glass <sjg@chromium.org>
The tests were broken by two separate commits which adjusted the output
when boards are listed. Fix this by adding back a PowerPC board and
putting the name of each board in the test.
Fixes: b9f7d881 (powerpc, 5xx: remove some "5xx" remains)
Fixes: 8d7523c5 (buildman: Allow showing the list of boards with -n)
Signed-off-by: Simon Glass <sjg@chromium.org>
Accessing the network slows down the test and limits the environment in
which it can be run. Add an option to disable network tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
This script runs the tests but does not report failure. Also it always
returns an exit code of 0 even on failure.
Fix these problems by checking the result of each test.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present these tests use the same filename as patman. This adds
confusion when running all tests, since error messages look very similar.
In fact binman tries to run the wrong tests at present.
Rename the tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
These test programs are includedd as binary files in U-Boot to avoid
having to build them (and associated toolchain differences). Instructions
on building are in the files themselves, but it seems better to provide
a Makefile which can be manually run when desired.
Add a Makefile, separate from the normal build system, to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is a debugging option in the Makefile to allow people to figure out
which u-boot.dtsi files are used in the build. But is it not easy to use
since it only shows files it finds, not those it is looking for. Update it
and update the mention of it to the docs.
Signed-off-by: Simon Glass <sjg@chromium.org>
A few header files still have a definition of CONFIG_ENV_SIZE, causing
warnings during buildman runs. This removes the duplicate definitions
from evb_px5.h, geekbox.h and rv1108_common.h.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip bootrom will enter download mode if it returns from
spl/tpl with a non-zero value and couldn't find a valid image
in the backup partition.
This patch provide a method to instruct the system to back to
bootrom download mode by checking the BROM_DOWNLOAD_FLAG register.
As the bootrom download function relys on some modules such as
interrupts, so we need to back to bootrom as early as possbile
before the tpl/spl code override the interrupt configurations.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
setup_boot_mode function use the same logic but different
mode register address across all the rockchip platforms,
so it's better to make this function reused across all the
platforms, and let the mode register address setting from
the config file.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
After applying the merged sysreset driver, there are build failures
due to an out-of-sync Makefile. This updates drivers/sysreset/Makefile
to address these build failures.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With all targets converted to generate prepadded images, this removes
the spl_boot0 field from our config structure and removes the unused
code-path (for images that are not prepadded): i.e. spl_boot0 is now
implied as 'true' and the code is specialised by removing the other
case.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There still are a few CONFIG_SPL_* options selected using defines from
rk3188_common.h instead of via Kconfig. This migrates those over to
Kconfig.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The BROM supports forcing it to enter download-mode, if an appropriate
result/cmd-word is returned to it. There already is a series to
support this in review, so this prepares the (newly C-version) of the
back-to-bootrom code to accept a cmd to passed on to the BROM.
All the existing call-sites are adjusted to match the changed function
signature.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.
With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.
Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The back-to-bootrom implementation for Rockchip has always relied on
the stack-pointer being valid on entry, so there was little reason to
have this as an assembly implementation.
This provides a new C-only implementation of save_boot_params and
back_to_bootrom (relying on setjmp/longjmp) and removes the older
assembly-only implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The previous setjmp-implementation (as a static inline function that
contained an 'asm volatile' sequence) was extremely fragile: (some
versions of) GCC optimised the set of registers. One critical example
was the removal of 'r9' from the clobber list, if -ffixed-reg9 was
supplied.
To increase robustness and ensure PCS-compliant behaviour, the setjmp
and longjmp implementation are now in assembly and closely match what
one would expect to find in a libc implementation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32. By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.
Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
The save_boot_params_ret() prototype (for those of us, that have a
valid SP on entry and can implement save_boot_params() in C), was
previously only defined for !defined(CONFIG_ARM64).
This moves the declaration to a common block to ensure the prototype
is available to everyone that might need it.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
Some Rockchip BROM versions (e.g. the RK3188 and RK3066) first read 1KB data
from NAND into SRAM and executes it. Then, following a return to bootrom, the
BROM loads additional code to SRAM (not overwriting the first block read) and
reenters at the same address as the first time.
To support booting either a TPL (on the RK3066) or SPL (on the RK3188) using
this model of having to count entries, this commit adds code to the boot0
hook to track the number of entries and handle them accordingly.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
This updates the BCM281xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This updates the BCM235xx boot0-hook to the updated boot0 semantics
by emitting _start and the vector table before the boot0 hook (as
was the case before).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Version-changes: 5
- ran 'whitespace-cleanup'
With the updated boot0 semantics (i.e. giving the boot0-hook control
over when and where the vector table is emitted), the boot0-hook for
the socfpga needs to be adjusted.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the boot0-hook inserting the additional padding to receive our
SPL magic, the SPL_TEXT_BASE can be aligned again.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable the spl_boot0 in SPL and use the pre-padding TAG memory,
the mkimage do not need to pad it but only need to replace the value
with correct TAG value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip SoCs bootrom design is like this:
- First 2KB or 4KB internal memory is for bootrom stack and heap;
- Then the first 4-byte suppose to be a TAG like 'RK33';
- The the following memory address end with '0004' is the first
instruction load and running by bootrom;
Let's use the boot0 hook to reserve the first 4-byte tag for all
the Rockchip SoCs.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[Commit message taken from an older patch by:]
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The '_start' is using as vector table base address, and will write
to VBAR register, so it needs to be aligned to 0x20 for armv7.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[Updated to current code base:]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The boot0 hook on ARM does not insert its payload before the vector
table. This is both a mismatch with thec comment above it and
contradict usage of the boot0 hook on ARM64.
To fix this (and unify the semantics for ARM and ARM64), we change the
boot0-hook semantics on ARM to match those on ARM64:
(1) if a boot0-hook is present it is inserted at the start of
the image
(2) if a boot0-hook is present, emitting the ARM vector table
(and the _start) symbol are suppressed in vectors.S and
the boot0-hook has full control over where and when it
wants to emit these
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Configure thermal configs to remain set by default for dra7xx and am57xx
devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Old url currently returns 403; modify to url that actually works
with current state of the list server
Signed-off-by: S. Lockwood-Childs <sjl@vctlabs.com>
With commit 84d46e7e89 ("tools: env: allow to print U-Boot version")
the fw_env utilities need the version.h header file. Building only
the envtools in a pristine build directory will fail due to missing
header files.
Make sure the header files are a dependency of the envtools target.
Fixes: 84d46e7e89 ("tools: env: allow to print U-Boot version")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When building on a multi-core machine for an SPL-enabled board that
also uses CONFIG_OF_EMBED, the following error can be encountered
due to a race condition:
make[3]: *** No rule to make target 'spl/dts/dt.dtb.o', needed by
'spl/dts/built-in.o'. Stop.
../scripts/Makefile.spl:364: recipe for target 'spl/dts' failed
make[2]: *** [spl/dts] Error 2
make[2]: *** Waiting for unfinished jobs....
A reliable way to trigger this race condition is to add "sleep 60" to
the end of the "arch-dtbs" rule's recipe in "dts/Makefile" and to build
U-Boot against a board which uses the CONFIG_OF_EMBED and CONFIG_SPL
options using "make -j8" or a similar command.
This commit corrects this race condition via the use of CONFIG_OF_EMBED
in the same way that commit 3c00a2c8b5 ("Makefile: Correct dependency
race condition with TPL") and commit 054b3a1e80 ("dm: Makefile: Build
of-platdata before SPL") use CONFIG_OF_SEPARATE.
Signed-off-by: M. Vefa Bicakci <m.v.b@runbox.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
0 is not a pointer. So do not compare pointers to 0.
Do not return 0 from functions with a pointer return
type.
Problem identified with Coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add some useful static code analysis scripts for coccinelle
copied from the Linux kernel v4.14-rc8:
Warn on check against NULL before calling free.
scripts/coccinelle/free/ifnullfree.cocci
Detect superfluous NULL check for list iterator.
scripts/coccinelle/iterators/itnull.cocci
Check if list iterator is reassigned.
scripts/coccinelle/iterators/list_entry_update.cocci
Check if list iterator is used after loop.
scripts/coccinelle/iterators/use_after_iter.cocci
Find wrong argument of sizeof in allocation function:
scripts/coccinelle/misc/badty.cocci
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Coccinelle is a program for static code analysis.
For details on Coccinelle see
http://coccinelle.lip6.fr/
Add scripts/coccicheck copied from Linux kernel v4.14.
The coccicheck script executes the tests *.cocci in
directory scripts/coccinelle by calling spatch.
In Makefile add a coccicheck target. You can use it with
make coccicheck MODE=<mode>
where mode in patch, report, context, org.
Add a copy of Linux v4.14 file Documentation/dev-tools/coccinelle.rst
as doc/README.coccinelle.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The iterator variable of list_for_each is never NULL.
if (1 || A) is always true.
Use break if entry found.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As per current android recommendation
https://source.android.com/devices/architecture/kernel/modular-kernels
1. Android recovery mode should contain both SOC and ODM
kernel modules in the recovery partition.
2. If a kernel module is required both in recovery and normal boot
mode, the module has to be located in recovery and vendor
partition seperately.
3. Kernel modules used in recovery mode should be independent
of vendor and odm partition
4. Recovery image should contain atleast
storage, display, keypad, battery and pmic modules.
Due to these requirements, recovery image size has increased
to >10MB.
This patch is to increase recovery partition size for TI devices
so that we dont see such flashing error
log:
sending 'recovery' (12560 KB)...
OKAY [ 0.436s]
writing 'recovery'...
FAILED (remote: too large for partition)
finished. total time: 0.458s
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
ld --version | scripts/ld-version.sh
fails with
awk: scripts/ld-version.sh:
line 4: regular expression compile failed (missing '(')
.*)
So let's refresh the script from Linux kernel v4.14-rc8.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
sym_arr is of type struct symbol **.
So in malloc we need sizeof(struct symbol *).
The problem was indicated by coccinelle.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add a driver for the I2C controller available on Amlogic Meson SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Currently the MX6QDL option is selected via CONFIG_SYS_EXTRA_OPTIONS,
but it is better to select it directly via Kconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The VPD data is used on a number of GE products. Move the parsing code to
a common location so that we can share this code.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Acked-by: Stefano Babic <sbabic@denx.de>
Add support for bootcounter on an EXT filesystem.
Sync configuration whitelist.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This reverts commit b8b9790e23.
Some wandboard variants no longer boot after this commit, so keep
the original delay to avoid the boot regression.
Reported-by: Varga Zsolt <vazso@vazso.hu>
Tested-by: Varga Zsolt <vazso@vazso.hu>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Command run setup_emmc will create gpt partitions for mmc 0 device
based on patitions variable.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Change dfu_alt_info variable to use the following altsetting:
uboot: To flash raw U-Boot
/zImage: boot: To copy kernel image
/imx6ul-pico-hobbit.dtb: To copy dtb file
rootfs: To copy rootfs
List the currently attached DFU capable USB devices running:
sudo dfu-util -l
Flash U-Boot:
sudo dfu-util -D u-boot.imx -a uboot
Copy boot files:
sudo dfu-util -D zImage -a /zImage
sudo dfu-util -D imx6ul-pico-hobbit.dtb -a /imx6ul-pico-hobbit.dtb
Flash rootfs:
sudo dfu-util -D rootfs.ext4 -a rootfs
To copy boot files you need to have a formated mmc 0:1 partition. To
format with ext4 filesystem you can use ums.
Run on target:
ums 0 mmc 0
and on host:
sudo mkfs.ext4 /dev/sdx1
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Currently the rootfs location is passed via mmcblk number and using
the UUID method to specify the rootfs location is a better approach
working even if mmcblk number for the eMMC changes depending on the
kernel versions.
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
We first introduce CONFIG_USE_BOOTCOMMAND, similar to
CONFIG_USE_BOOTARGS. We then migrate CONFIG_BOOTCOMMAND for most
CONFIG_DISTRO_DEFAULT users. In some cases platforms have a complex
scheme around this usage, and these have been defered for the moment so
that platform maintainers can work on a migration plan.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Since CONFIG_DEFAULT_CONSOLE is already started with "console=",
the console argument in CONFIG_EXTRA_ENV_SETTINGS is expanded to
"console=console=ttySAC1,115200n8" and this causes the wrong
console device.
#define CONFIG_DEFAULT_CONSOLE "console=ttySAC1,115200n8\0"
...
#define CONFIG_EXTRA_ENV_SETTINGS \
"console=" CONFIG_DEFAULT_CONSOLE
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UARTs 1 through 5 were missing in the code - added.
Also pick the default according to the configuration setting for the
console index.
Signed-off-by: Ronald Landheer-Cieslak <ronaldlandheercieslak@eaton.com>
This patch is to change U-Boot PCI bus assignement compliant with Linux.
It means each PCIe controller's bus number is 0, not the current maximum
PCI bus number, when start to scan this controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
While commit 36d35345b1 ("tpm: add missing va_end") added
some missing calls to va_end(), it missed a few places.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
TPM_NV_PER_PPREAD: physical presence needed for reading
TPM_NV_PER_WRITEDEFINE: persistent write lock by writing size 0
TPM_NV_PER_WRITEALL: write in one go
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to obtain random data from the TPM.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Added commit message, add cast to min()
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Allow the platform to define a partition by name at the end of which
the environment data will be located.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
In U-boot, serial_tstc was use to determine is there have a character in
serial console that pending for read. If there is no "pending" function
implemented in serial driver, the serial-uclass will return "true(1)"
to indicate there have a character pending to read.
Thus, read a character from nulldev serial will result in continuous
getting -EAGAIN return which might lead system to hang.
This commit is to fix a bug in nulldev serial which implement "pending"
function in nulldev serial to always indicate there is no character in
console that pending for read.
Signed-off-by: Wilson Lee <wilson.lee@ni.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Keng Soon Cheah <keng.soon.cheah@ni.com>
Cc: Chen Yee Chew <chen.yee.chew@ni.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
This is required in the case where U-Boot is typically loaded and run at
a particular address, but for some reason the RAM at that location is not
available, e.g. due to memory fragmentation loading other boot binaries or
firmware, splitting an SMP complex between various different OSs without
using e.g. the EL2 second-stage page tables to hide the memory asignments,
or due to known ECC failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
It can be useful to record how long tests take; this can help debug slow
running test systems or track changes in performance over time. Enhance
the test system to record timestamps while running test:
- Whenever a new log file section is started.
- After U-Boot is started and communication has been established.
- After each host or U-Boot command is executed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Fix clock division factor initialization for RCC_PLLCFGR
registers.
PLLR bits (bit 31-28) in RCC_PLLCFGR must not be cleared,
it's a forbidden value. So update RCC_PLLCFGR using
clrsetbits_le32() to set only necessary bits fields.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert this driver to driver model.
This driver is also used by VEXPRESS platforms which doesn't
use driver model.
Tested on STM32F746 and STM32F769 platforms.
Signed-off-by: Christophe Priouzeau <christophe.priouzeau@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Update arm_pl180_mmci_init() prototype by adding struct mmc**
param. This is needed before converting this driver to driver model
in order to use arm_pl180_mmci_init() in driver model and in none
driver model implementation
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This option provides better performance and should really always be
enabled. Make this be default y.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Jeroen Hofstee <jeroen@myspectrum.nl>
This patch adds support for the Internal RMII Ethernet PHY on the
Amlogic P212 Reference Board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On Amlogic Meson GXL/GXM, supplementary ethernet configuration registers
were added to configure the internal RMII PHY interface.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic Meson GXL/GXM families embeds an internal RMII Ethernet PHY.
The PHY acts as a generic PHY but needs a slight configuration right
before it's configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
Make them a wrapper of scripts/dtc/libfdt/*. This is exactly what
Linux does to sync libfdt. In order to make is possible, import
<linux/libfdt.h> and <linux/libfdt_env.h> from Linux 4.14-rc5.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
The fdt_region.c is U-Boot own file.
I did not touch them in order to avoid unpredictable impact.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this typedef in the same place as in Linux. This is necessary
to refactor libfdt inclusion.
U-Boot also defines it in include/compiler.h. Of course it should
not do that, but I do not want to open a can of worms.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Prior to this commit, tools/Makefile pulls all libfdt files from
lib/libfdt.
lib/libfdt/ and scripts/dtc/libfdt have the same copies for the
followings 6 files:
fdt.c fdt_addresses.c fdt_empty_tree.c fdt_overlay.c fdt_strerr.c
fdt_sw.c
This commit changes them to #include ones from scripts/dtc/libfdt.
Unfortunately, U-Boot locally modified the following 3 files:
fdt_ro.c fdt_wip.c fdt_rw.c
I did not touch them in order to avoid unpredictable impact.
The fdt_region.c is U-Boot own file. This is also borrowed from
lib/libfdt/.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify libfdt_internal.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fortunately, U-Boot did not modify fdt.h locally.
Change it to a wrapper of scripts/dtc/libfdt/fdt.h, which will be
periodically synced with the upstream DTC (or kernel).
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, pylibfdt is always compiled if swig is installed on your
machine. It is really annoying because most of targets (excepts
x86, sunxi, rockchip) do not use dtoc or binman.
"checkbinman" and "checkdtoc" are wrong. It is odd that the final
build stage checks if we have built necessary tools. If your platform
depends on dtoc/binman, you must be able to build pylibfdt. If swig
is not installed, it should fail immediately.
I added PYLIBFDT, DTOC, BINMAN entries to Kconfig. They should be
property select:ed by platforms that need them. Kbuild will descend
into scripts/dtc/pylibfdt/ only when CONFIG_PYLIBFDT is enabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The pylibfdt is used by dtoc (and, indirectly by binman), but there
is no reason why it must be generated in the tools/ directory.
Recently, U-Boot switched over to the bundled DTC, and the directory
structure under scripts/dtc/ now mirrors the upstream DTC project.
So, scripts/dtc/pylibfdt is the best location.
I also rewrote the Makefile in a cleaner Kbuild style.
The scripts from the upstream have been moved as follows:
lib/libfdt/pylibfdt/setup.py -> scripts/dtc/pylibfdt/setup.py
lib/libfdt/pylibfdt/libfdt.i -> scripts/dtc/pylibfdt/libfdt.i_shipped
The .i_shipped is coped to .i during building because the .i must be
located in the objtree when we build it out of tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds the following commits from upstream:
b1a6003 tests: Add a test for overlays syntactic sugar
737b2df overlay: Add syntactic sugar version of overlays
497432f checks: Use proper format modifier for size_t
22a65c5 dtc: Bump version to v1.4.5
c575d80 Add fdtoverlay to .gitignore
b6a6f94 fdtoverlay: Sanity check blob size
8c1eb15 pylibfdt: Use Python2 explicitly
ee3d26f checks: add interrupts property check
c1e7738 checks: add gpio binding properties check
b3bbac0 checks: add phandle with arg property checks
[ sync with Linux commit: 4201d057ea91c3d6efd2db65219bc91fae413bc2 ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
libfdt has gained some new files. We need to include them in the
kernel's copy.
Reported-by: Kyle Yan <kyan@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ Linux commit: 4322323058f010274564006d61945187a15b6361 ]
This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.
This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Add the Amlogic Meson GXL pinctrl support based on the GXBB driver and
the synchronized DTS from Linux 4.13.5
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Synchronize the Amlogic ARM64 dts from mainline Linux 4.13.5
In the preparation of the support of the Amlogic P212 board,
import the corresponding meson-gxl-s905x-p212.dts file.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
All regulators are hooked to EN_Pin at reset so that EN Pin controls
their state. Hook the LDO1 regulator to EN pin which at reset is not
hooked. This applies only to LP8733.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For the DM TPS65910 driver I'm working on, querying the MPU voltage
should return a value in uV. This value can then be used by the
regulator's standard function set_value to set the MPU voltage.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The offset of the permanent flags structure is in a different
place in the response compared to what the code is doing,
which gives us a completely useless result.
Fix by replacing hand-crafted code with generic parser
infrastructure.
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
The maximum length of the name of the image is
obviously not sizeof(), which is just the
length of a pointer, but IH_NMLEN.
fixes: 62cf11c092
("SPL: Limit image name print length")
Signed-off-by: André Draszik <adraszik@tycoint.com>
Acked-by: Simon Glass <sjg@chromium.org>
This currently causes a warning in sandbox and will not do the right
thing:
drivers/core/read.c: In function ‘dev_read_addr_ptr’:
drivers/core/read.c:64:44: warning: cast to pointer from integer of
different size [-Wint-to-pointer-cast]
return (addr == FDT_ADDR_T_NONE) ? NULL : (void *)addr;
Use map_sysmem() which is the correct way to convert an address to a
pointer.
Fixes: c131c8bca8 (dm: core: add dev_read_addr_ptr())
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the compiler is free to place a char array to any address in
memory (in this case the stack), also to a non word aligned address the
function "fdt_prop_parse" runs into troubles upon it wants to write some
(fdt32_t *) to such a variable (if it has been placed to a none word
aligned address).
To avoid this we tell the compiler to always align this scratchpad to a
word aligned address.
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Tested-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
All current ClearFog SOMs have the SPI flash populated. Enable SPI flash in
the device tree.
Add an alias to the SPI bus so that the 'sf' command can probe the flash on
bus 1.
Add the "spi-flash" compatible string to make the standard SPI flash driver
probe the device.
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
The production variant of the SPI flash used by the clearfog
devices are based on winbond chips. Additionally enable
SPI_FLASH_BAR since some variants will have 16MB of flash
that requires this to be enabled.
Remove the default speed and mode; these values are taken from the
device tree when CONFIG_DM_SPI_FLASH is enabled.
Add default bus, so that 'sf' detects the SPI flash by default.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: remove speed/mode; add bus; move winbond to defconfig]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the driver by default for the clearfog boards since the external
port is configured for XHCI.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: split from the SoC setup patch]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes the USB 3.0 support for the a38x SOC.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DISTRO_DEFAULTS for
mvebu_db_armada8k_defconfig
mvebu_mcbin-88f8040_defconfig
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The board uses T-topology for the four x16 DRAM chips, so remove
the write-leveling from the SPL as that is only usefly on fly-by
topology and can be harmful on T-topology. Also update the DRAM
timing with values from calibration on multiple boards.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Update help message for "mac" command to reflect correct descriptions
and parameters.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Value provided in MC_MEM_SIZE_ENV_VAR is in hex. Use 16 as base
in simple_strtoul.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Distro boot support gives flexibility to run distro RFS like Ubuntu
being deployed from SD card or SATA drive. If it fails to detect
external storage, fall back to qspi/sd boot.
Enable this by default in RDB's defconfig by selecting
CONFIG_DISTRO_DEFAULTS
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Zhang Ying <zhangying@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently the chipselect used to identify the corresponding NAND chip
is stored at the controller and only set during fsl_ifc_chip_init().
This way, only the last NAND chip is working, as the previous value
of cs_nand gets overwritten.
In order to solve this issue the chipselect is computed on demand by
evaluating the bank variable. Thus, the correct chipselect for each
NAND chip operation is used.
Tested on hardware with two NAND chips connected to the IFC
controller.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Scott Wood <oss@buserror.net>
[YS: reformatted commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
The zero value returned from qbman_swp_acquire() is an error
condition meaning no free buffer for allocation.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kushwaha Prabhakar <prabhakar@freescale.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
This reverts commit c61d0009fe.
A tbs2910 board user reported a very slow console frambuffer as
regression in current u-boot. I could bisect this down to the
above mentioned commit.
This revert brings back the fast framebuffer console (one
cache flush per string in puts(), not after each char).
Reported-by: Uwe Scheffler <scheffler.u@web.de>
Signed-off-by: Soeren Moch <smoch@web.de>
Tested-by: Uwe Scheffler <scheffler.u@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The eMMC is 1V8 device only and the signaling is always 1V8,
fix the DT for Salvator-X/XS to describe the hardware correctly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
After updating u-boot from v2016.01 to 2017.09, issue with
"SATA link 0 timeout." on my Cubietruck board.
mdelay milled after moving satapwr code to board.
"sunxi: Turn satapwr on from board_init"
(sha1: 9fbb0c3aa4)
After adding the "mdelay(500);"
line that was lost in the path the error is gone.
Signed-off-by: Werner Böllmann <Werner.Boellmann@fh-dortmund.de>
[Rebased and updated change and commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Only the H3/H5 SoCs have an internal PHY and its related clock and
reset controls.
Use an #ifdef to guard the internal PHY control code block so it
can be built for other SoCs, such as the A83T or A64.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
due misnaming of CONFIG_SUN4I_EMAC in include/configs/sunxi-common.h,
likely missed in:
commit 3146f0c017 ("Move PHYLIB to Kconfig")
Signed-off-by: Artturi Alm <artturi.alm@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The following error has been observed on i.MX25 with a high-speed SDSC
card:
Data Write Failed in PIO Mode.
It was caused by the timeout set on PRSSTAT.BWEN, which was triggered
because this bit takes 15 ms to be set after writing the first block to
DATPORT with this card. Without this timeout, all the blocks are
properly written.
This timeout was implemented by decrementing a variable, so it was
depending on the CPU frequency. Fix this issue by setting this timeout
to a long enough absolute duration (500 ms).
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When a high speed card is connected to mx51evk the following error is seen:
U-Boot 2017.11-rc2 (Oct 18 2017 - 13:49:26 -0200)
CPU: Freescale i.MX51 rev3.0 at 800 MHz
Reset cause: POR
Board: MX51EVK
DRAM: 512 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX51 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX51, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
The i.MX51 ts4800 board already selects this option, but it is better
to move this selection to the i.MX51 SoC level instead.
Successfully tested with a high speed SD card on a mx51evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
When a high speed card is connected to mx25 the following error is seen:
U-Boot 2017.11-rc2-00104-gb79372a (Oct 31 2017 - 11:02:22 -0200)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
No arch specific invalidate_icache_all available!
MMC: FSL_SDHC: 0
*** Warning - read failed, using default environment
In: serial
Out: serial
Err: serial
Net: FEC
Hit any key to stop autoboot: 0
=> saveenv
Saving Environment to MMC...
Writing to MMC(0)... failed
, which prevents any usage of the SD card.
The root cause for the failure is the eSDHC-A001 erratum:
"eSDHC-A001 : Data timeout counter (SYSCTL[DTOCV]) is not reliable for
values of 0x4,0x8, and 0xC" that is listed
on some PowerArchitecture chips:
https://www.nxp.com/files-static/32bit/doc/errata/MPC8379ECE.pdf
Even though eSDHC-A001 is not documented on the i.MX25 errata document,
I have confirmed with the NXP design team that this erratum does affect
i.MX25, so fix the problem by selecting SYS_FSL_ERRATUM_ESDHC_A001
at SoC level.
Successfully tested with a high speed SD card on a mx25pdk board.
Suggested-by: Benoît Thébaudeau <benoit@wsystem.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Tested-by: Otavio Salvador <otavio@ossystems.com.br> # mx25pdk
The motivation for moving MX25 selection to Kconfig is to be
able to better handle MX25 specific errata, so that an errata option
can be selected at SoC level instead of board level.
This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
The check in part_get_info_extended() for a successful partition
searching misses a condition for extended partition. In case of
(ext_part_sector == 0), we should anyway mark the partition as found,
even if it's an extended partition, i.e. (is_extended(pt->sys_ind) == 0).
Otherwise, the extended partition (type 0x0f) will never be identified,
and the following recursive call to part_get_info_extended() will get a
wrong 'part_num' and 'which_part' parameter. In the end, all those
partitions in extended table will not be identified.
Let's add the missing OR condition of (ext_part_sector == 0) for
is_extended() check to fix the problem.
The issue is discovered by running fastboot flash to an extended
partition on eMMC.
$ fastboot flash mmcsda5 cache.img
target reported max download size of 536870912 bytes
sending 'mmcsda5' (18796 KB)...
OKAY [ 2.144s]
writing 'mmcsda5'...
FAILED (remote: cannot find partition)
finished. total time: 2.261s
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before this patch one could receive following errors when executing
"gpt write" command on machine with cache enabled:
display5 factory > gpt write mmc ${mmcdev} ${partitions}
Writing GPT:
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
success!
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is called when signing configuration nodes. Adjust
the error message.
I do not know why we do not need to show the error message in case of
ENOSPC. Remove the if-conditional that seems unnecessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If -K option is missing when you sign image nodes, it fails with
an unclear error message:
tools/mkimage Can't add hashes to FIT blob: -1
It is hard to figure out the cause of the failure.
In contrast, when you sign configuration nodes, -K is optional because
fit_config_process_sig() returns successfully if keydest is unset.
Probably this is a preferred behavior when you want to update FIT with
the same key; you do not have to update the public key in this case.
So, this commit changes fit_image_process_sig() to continue signing
without keydest. If ->add_verify_data() fails, show a clearer error
message, which has been borrowed from fit_config_process_sig().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "algo_name" points to a property in a blob being edited. The
pointer becomes stale when fit_image_write_sig() inserts signatures.
Then crypto->add_verify_data() writes wrong data to the public key
destination.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
test_gpt generates a persistent disk image which can be re-used across
multiple test runs. Currently, if the Python code that generates the disk
image change, the image is not regenerated, which could cause test
failures e.g. if a test was updated to expect some new partition name or
size, yet the persistent disk image contained the old name or size. This
change introduces functionality to regenerate the disk image if the
instructions to generate the image have changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The fw_env utility family has a default environment compiled in
which ties it quite strongly to the U-Boot source/config it has
been built with. Allow to display the U-Boot version it has been
built with using the -v/--version argument.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Designated initializers are more readable because we do not
have to check the order in the struct definitions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <trini@konsulko.com>
When HDMI is not initialized (e.g. no monitor is plugged), the current
SimpleFB code will still create a broken SimpleFB node.
Detect whether HDMI is initialized when creating SimpleFB node.
Fixes: be5b96f0e4 ("sunxi: setup simplefb for Allwinner DE2")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
The patch:
"dm: ahci: Unwind the confusing init code"
(sha1: 7cf1afce7f)
introduce bug for ceva sata because port didn't start.
On the other hand the dwc_ahci.c was fixed correctly.
Do the same change for ceva too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
This also brings the benefit to allowing setup_sata() to be called for the
mx6qp wandboard variant.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Commit 001cdbbb32 ("imx: mx6slevk: enable more DM drivers") breaks
MMC support in U-Boot proper on the mx6slevk_spl_defconfig target:
U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18)
Trying to boot from MMC1
U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300)
CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 33C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
MMC Device 1 not found
*** Warning - No MMC card found, using default environment
As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its
board file does not register the mmc controller for U-Boot proper,
let's fix this by adding CONFIG_DM_MMC=y and device tree support.
While at it, add more DM drivers, so that it becomes closer to
mx6slevk_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On Vybrid SoCs U-Boot gets loaded into GFX SRAM which is 512KiB.
Currently 32KiB is reserved for the IMX header. However, this is
not reflected in the size limit. In v2017.11-rc2 the actual size
limit (512KiB-32KiB) has been reached for Colibri VF61, which
lead to a successful build of U-Boot but not a working binary.
The IMX header is much smaller than 32KiB, typically around 1KiB.
Decrease the reserved size to 4KiB and specify the correct U-Boot
size limit. Apply this new base address and limit for all Vybrid
based boards.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
As reported by Jonathan Gray:
"After the recent changes to add SimpleNetworkProtocol to efi_loader
when booting off mmc via an efi payload that doesn't use
SimpleNetworkProtocol U-Boot's fec_mxc driver will now display
various "error frame" messages.
....
MMC Device 1 not found
MMC Device 2 not found
MMC Device 3 not found
Scanning disks on sata...
Found 6 disks
reading efi/boot/bootarm.efi
67372 bytes read in 32 ms (2 MiB/s)
## Starting EFI application at 12000000 ...
>> OpenBSD/armv7 BOOTARM 1.0
error frame: 0x8f57ec40 0x00003d74
error frame: 0x8f57ec40 0x00007079
error frame: 0x8f57ec40 0x00006964
error frame: 0x8f57ec40 0x00006f6f
error frame: 0x8f57ec40 0x0000726f
error frame: 0x8f57ec40 0x00002074
error frame: 0x8f57ec40 0x00006f6f"
Heinrich Schuchardt explains:
"A receive FIFO overrun can be expected if network packages are not
processed.
With the network patches we check if a package is available quite often."
Move the "error frame" messages to debug level so that a clean output
log can be seen.
Reported-by: Jonathan Gray <jsg@jsg.id.au>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Many MAINTAINERS files are in subdirectories.
We should enable searching these.
Reported-by: Walt Feasel <waltfeasel@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Resort to malloc_cache_aligned() rather than malloc() which also removes
'CACHE: Misaligned operation at range' warnings.
Signed-off-by: Niko Mauno <niko.mauno@vaisala.com>
With the introduction of EFI variable support, we also wanted to persist
these EFI variables. However, the way it was implemented we ended up
persisting all U-Boot environment variables on every EFI boot.
That could potentially lead to unexpected side effects because variables
that were not supposed to be written to persisted env get written. It also
means we may end up writing the environment more often than we should.
For this release, let's just disable EFI variable persistence and instead
implement it properly for the next one.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fixes: ad644e7c18 ("efi_loader: efi variable support")
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable support for loadables in SEC firmware FIT image. Currently
support is added for single loadable image.
Brief description of implementation:
Add two more address pointers (loadable_h, loadable_l) as arguments to
sec_firmware_init() api.
Create new api: sec_firmware_checks_copy_loadable() to check if loadables
node is present in SEC firmware FIT image. If present, verify loadable
image and copies it to secure DDR memory.
Populate address pointers with secure DDR memory addresses where loadable
is copied.
Example use-case could be trusted OS (tee.bin) as loadables node in SEC
firmware FIT image.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Change DDR allocated for secure memory from 2 MB to 66 MB. This
additional 64 MB secure memory is required for trusted OS running
in Trusted Execution Environment using ARMv8 TrustZone.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since TX delay is now enabled only in PHY_INTERFACE_MODE_RGMII_ID
PHY_INTERFACE_MODE_RGMII_TXID.
These change where introduced in phy driver in commit 05b29aa0cb
("net: phy: realtek: fix enabling of the TX-delay for RTL8211F").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
On ls1012a soc, core clock source frequency is fixed at 100Mhz.
Generic timer frequency is core clock source divided by 4, which
is 25Mhz.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Memory allocated via malloc is not guaranteed to be zeroized.
So explicitly use calloc instead of malloc.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
This comment creates a wrong entry in config_whitelist.txt.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro only appears in commented-out lines. It is not referenced
by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This macro is defined, but not referenced by anyone.
I did not touch config_whitelist.txt - the CONFIG will be dropped
by the next re-sync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher<hs@denx.de>
CONFIG_SYS_I2C_FTI2C010 is not enabled by anyone.
Commit 2852709676 ("dm: i2c: Add a note to I2C drivers which need
conversion") prompted to convert this driver to DM before June 2017,
but not converted yet.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
This driver was used by Blackfin boards, but Blackfin support is
gone. There is no user of this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Extend DE2 driver with LCD support. Tested on Pinebook which is based
on A64 and has ANX6345 eDP bridge with eDP panel connected to it.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: rebased v5 on u-boot-video/master]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The supported sleep states are generic on Intel processors. Move the
ASL definition to the common place.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On some platforms (eg: Braswell), the FSP will not produce the
graphics info HOB unless you plug some cables to the display
interface (eg: HDMI) on the board. Add such notes in the FSP
video driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Intel Braswell FSP requires SPI controller settings to be locked down,
let's do this in the chrryhill.dts and remove previous Kconfig option.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some Intel FSP (like Braswell) does SPI lock-down during the call
to fsp_notify(INIT_PHASE_BOOT). But before SPI lock-down is done,
it's bootloader's responsibility to configure the SPI controller's
opcode registers properly otherwise SPI controller driver doesn't
know how to communicate with the SPI flash device.
Rather than passively doing the opcode configuration, let's add a
simple DTS property "intel,spi-lock-down" and let the driver call
the opcode configuration function if required by such FSP.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit 1e6ebee667.
It's not appropriate to call the Intel SPI driver specific stuff in
the FSP codes. We may add a simple DTS property "intel,spi-lock-down"
and let the Intel SPI driver call these stuff instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
In an S3 resume path, MRC cache is mandatory. Enforce the dependency
in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Imply does not work for a Kconfig choice. Update ENV_IS_IN_SPI_FLASH
to be the default one for Intel Braswell.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It was observed that when booting Linux kernel on Intel Cherry Hill
board, unexpected crash happens quite randomly. Sometimes kernel
just oops, while sometimes kernel throws MCE errors and hangs:
mce: [Hardware Error]: Machine check events logged
mce: [Hardware Error]: CPU 0: Machine Check: 0 Bank 4: c400000000010151
mce: [Hardware Error]: TSC 0 ADDR 130f3f2c0
mce: [Hardware Error]: PROCESSOR 0:406c3 TIME 1508160686 SOCKET 0 APIC 0 microcode 363
This looks like a hardware error per mcelog. After debugging, it
seems turning off turbo mode on the processor does not expose this
behavior, although U-Boot runs OK with turbo mode on. Suspect it is
related to an errata of Braswell processor.
To fix this, remove the Braswell cpu driver which does the turbo
mode configuration, and switch to use the generic cpu-x86 driver.
Also there is a configuration option in the FSP that turns on the
turbo mode and that has been turned off too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With latest codes on mainstream master, Intel Galileo board does not
boot unfortunately. Git biset leads to b383d6c0 "bootstage: Convert
to use malloc()".
Disable bootstage support to make it boot again. The root cause needs
to be investigated however.
Fixes: b383d6c0 ("bootstage: Convert to use malloc()")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This is a eDP bridge similar to ANX9804, it allows to connect eDP panels
to the chips that can output only parallel signal
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: fixed most checkpatch errors/warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This header will be used in anx6345 driver
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
[agust: moved header to drivers/video]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add an operation to read EDID, since bridge may have ability to read
EDID from the panel that is connected to it, for example LCD<->eDP bridge.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
As the support of EFI boot on Allwinner H3 is broken, we still need to
use simplefb to pass the framebuffer to Linux.
Add code to setup simplefb for Allwinner DE2 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an option to indicate that the video driver should setup a SimpleFB
node that passes the video framebuffer initialized by U-Boot to the
operating system kernel.
Currently only the Allwinner DE driver uses this option, and the
definition of this option in the sunxi-common.h config header is
converted to an imply of this option from CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The sunxi DE1 video option used to be CONFIG_VIDEO, which has the same
name as the "Enable legacy video support" option in
drivers/video/Kconfig.
Change the option name to CONFIG_VIDEO_SUNXI, which is really used by
Makefile under drivers/video/sunxi/, and defined in sunxi-common.h
when CONFIG_VIDEO is selected before this change. Now CONFIG_VIDEO_SUNXI
selects CONFIG_VIDEO and the usages of CONFIG_VIDEO in sunxi Kconfig and
config headers are all converted to use CONFIG_VIDEO_SUNXI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
The U-Boot binary may trip over its actual allocated size in the storage.
In such a case, the environment will not be readable anymore (because
corrupted when the new image was flashed), and any attempt at using saveenv
to reconstruct the environment will result in a corrupted U-Boot binary.
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi M2-Magic is a small board with an Allwinner A33, an eMMC, a
wifi chip and some pin headers. Enable support for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Encountered an issue where fastboot can't write to NAND on a CHIP_pro,
the symbol was neither present in the board's config header, nor the
Kconfig, this patch puts it in the Kconfig and defaults on when
SUNXI_NAND is selected.
Signed-off-by: Ben Young <computermouth@crunchbangplusplus.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As explained in arch/arm/mach-sunxi/clock_sun8i_a83t.c, clk for CPU
clusters is computed as clk = 24*n. However, the current formula is clk
= 24*(n-1).
This results in a clock set to a frequency that isn't specified as
possible for CPUs.
Let's use the correct formula.
Fixes: f542948b1e ("sunxi: clk: add basic clocks for A83T")
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The Allwinner SPI flash SPL boot support is guarded by the SPL_SPI_SUNXI
symbol. But despite its generic name, the actual only use case for this
is to provide SPI flash support to the SPL, which requires
CONFIG_SPL_SPI_FLASH_SUPPORT to be defined.
Select this symbol from the SPL_SPI_SUNXI Kconfig definition. This
avoids doing this explicitly in the defconfig, and fixes SPI booting on
the Pine64 SoPine (and -LTS version) and the OrangePi Win board (both with
SPI flash).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Provide a Kconfig option that we can use as dependency for
features that are broken. This allows to easily disable them
without removing the code.
As no short text is supplied the option will not appear in
menuconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
As you see in crypto_algos in common/image-sig.c, the algorithm
should be either "rsa2048" or "rsa4096". "rs2048" is a typo.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both "conf_name" and "sig_name" point to the name of config node.
The latter should be the name of the signature node.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
don't use prettyprint_part_size() in create_gpt_partitions_list()
that avoid to align offset and size to 1 MiB and increase precision for
start and size.
This patch avoid the risk to change partition size and lost data during
rename or swap.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Add test of first and last LBA in gpt for rename and swap.
Only the name is expected to change, so test 3 columns
for part command
1: first LBA (start)
2: last LBA (end)
3: partition name
After rename, the last LBA change and it is a error in current U-Boot code
+ "first" = 0x7ff : invalid value (<start)
+ "second" = 0x17ff => size increasing !
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
+ test write for one partition on all the device (size=0)
+ test write with disk uuid and 2 partitions
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
the partition starting at 0x4400 is refused with overlap error:
$> gpt write mmc 0 "name=test,start=0x4400,size=0"
Writing GPT: Partition overlap
error!
even if the 0x4400 is the first available offset for LBA35 with default
value:
- MBR=LBA1
- GPT header=LBA2
- PTE= 32 LBAs (128 entry), 3 to 34
And the command to have one partition for all the disk failed also :
$> gpt write mmc 0 "name=test,size=0"
After the patch :
$> gpt write mmc 0 "name=test,size=0"
Writing GPT: success!
$> part list mmc 0
Partition Map for MMC device 0 -- Partition Type: EFI
Part Start LBA End LBA Name
Attributes
Type GUID
Partition GUID
1 0x00000022 0x01ce9fde "test"
attrs: 0x0000000000000000
type: ebd0a0a2-b9e5-4433-87c0-68b6b72699c7
type: data
guid: b4b84b8a-04e3-4000-0036-aff5c9c495b1
And 0x22 = 34 LBA => offset = 0x4400 is accepted as expected
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
add sandbox test for some gpt sub-command
- gpt read / part list : read the gpt partition created by sgdisk on host
test start, size, LBA and name output
- gpt verify : verify the gpt partition create by sgdisk on host
PS: persistent data test_gpt_disk_image.bin are udpated
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
copy the persistent gpt binary file as it can be modified during the test
that avoid issue if the test fail: the test always restart with clean file
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
RTC_CONFIG_D register contains the day within the month to generate
an alarm, not the month. This corrects the printf to indicate it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Remove hardcoded ftd file name from environment variables.
Use CONFIG_DEFAULT_FDT_FILE macro instead.
Signed-off-by: Michal Oleszczyk <m.oleszczyk@grinn-global.com>
Commit 06ad970b53 ("powerpc: mpc85xx: Implemente workaround for CPU
erratum A-007907") clears L1CSR2 for the boot core, but other cores
don't run through the workaround. Add similar code for secondary
cores to clear DCSTASHID field in L1CSR2 register.
Signed-off-by: York Sun <york.sun@nxp.com>
All users of this macro have been converted. Remove MTDDEBUG and
related CONFIG options.
ubifs_dbg_msg_key() is kept. It is silent unless DEBUG is defined.
I am not touching scripts/config_whitelist.txt. The deprecated options
will be dropped by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In old days, the MTD subsystem in Linux had debug facility like
DEBUG(MTD_DEBUG_LEVEL1, ...).
They were all replaced with pr_debug() until Linux 3.2. See Linux
commit 289c05222172 ("mtd: replace DEBUG() with pr_debug()").
U-Boot still uses similar macros. Covert all of them for easier sync.
Done with the help of Coccinelle.
The semantic patch I used is as follows:
// <smpl>
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2)
+pr_debug(e2)
@@
expression e1, e2;
@@
-MTDDEBUG(e1, e2,
+pr_debug(e2,
...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit dd74b945af ("ARM: uniphier: use pr_() instead of printf()
where appropriate"), but I missed to update this file for some reason.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If the environment "verify" is set to n, the image verification
is entirely skipped. Remove it as a preparation for verified boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The default value of CONFIG_SYS_BOOTM_LEN, 0x800000, causes error
when uncompressing Image.gz out of FIT image.
Uncompressing Kernel Image ... Error: inflate() returned -5
Image too large: increase CONFIG_SYS_BOOTM_LEN
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
UniPhier 32-bit SoCs use CONFIG_SPL_OF_CONTROL. So, many nodes must
be marked as dm-pre-reloc to prevent fdtgrep from stripping them off.
Sprinkling U-Boot-specific properties all over the place is painful
because DT files are synced with Linux from time to time.
Split u-boot,dm-pre-reloc out to uniphier-v7-u-boot.dtsi, which is
appended to UniPhier V7 DTS before the build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The option is never enabled by anyone. Remove the code surrounded
by its ifdef. This should be handled by the clock/reset drivers.
CONFIG_UNIPHIER_ETH in scripts/config_whitelist.txt will be dropped
by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
I thought commit d37d31849c ("ARM: uniphier: enable DWC3 xHCI
driver") enabled CONFIG_USB_DWC3_UNIPHIER, but CONFIG_USB_XHCI_DWC3
was missing in uniphier_v7_defconfig. Re-add.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
We add the various SMC91XX symbols to drivers/net/Kconfig and then this
converts the following to Kconfig:
CONFIG_SMC911X
CONFIG_SMC911X_BASE
CONFIG_SMC911X_16_BIT
CONFIG_SMC911X_32_BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Apply to the rest of the tree, re-squash old and new patch]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_MXC
CONFIG_NAND_OMAP_GPMC
CONFIG_NAND_OMAP_GPMC_PREFETCH
CONFIG_NAND_OMAP_ELM
CONFIG_SPL_NAND_AM33XX_BCH
CONFIG_SPL_NAND_SIMPLE
CONFIG_SYS_NAND_BUSWIDTH_16BIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Finish migration of CONFIG_SPL_NAND_SIMPLE, fix some build issues,
add CONFIG_NAND_MXC so we can do CONFIG_SYS_NAND_BUSWIDTH_16BIT]
Signed-off-by: Tom Rini <trini@konsulko.com>
I've missed to add the ACPI resume support to this x86 build target.
This patch adds the ACPI resume support enabling S3 suspend /
resume.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Up to now we depended on an exported variable to build u-boot.rom.
We should be able to specify it in the configuration file, too.
With this patch this becomes possible using the new Kconfig option
CONFIG_BUILD_ROM.
This option depends on CONFIG_X86 and is selected in
qemu-x86_defconfig and qemu-x86_64_defconfig.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Azalia configuration may be different across boards, hence it's not
appropriate to do that in the SoC level. Instead, let's make the
SoC update_fsp_azalia_configs() routine as a weak version, and do
the actual work in the board codes.
So far it seems only som-db5800-som-6867 board enables the Azalia.
Move the original codes into som-db5800-som-6867.c.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
At present we directly pass the Azalia config pointer to the FSP UPD.
This updates to use a function to do the stuff, like Braswell does.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
So far there are two copies of Azalia struct defines with one in
baytrail and the other one in braswell. This consolidates these
two into one, put it in the common place, and remove the prefix
pch_ to these structs to make their names more generic.
This also corrects reset_wait_timer from us to ms.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This is only needed when graphics console is used. For kernel with
native graphics driver, this can be turned off to speed up.
Change this option's default to n in the Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It was observed that when booting a Ubuntu 16.04 kernel, doing ACPI
S3 suspend/resume sometimes causes the Ubuntu kernel hang forever.
The issue is however not reproduced with a kernel built from i386/
x86_64 defconfig configuration.
The unstability is actually caused by unexpected interrupts being
generated during the S3 resume. For some unknown reason, FSP (gold4)
for BayTrail configures the GPIO DFX5 PAD to enable level interrupt
(bit 24 and 25). As this pin keeps generating interrupts during an
S3 resume, and there is no IRQ requester in the kernel to handle it,
the kernel seems to hang and does not continue resuming.
Clear the mysterious interrupt bits for this pin.
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
As "v" is a local variable in stm32_i2c_choose_solution()
"v" has to be copied into "s" to avoid data abort in
stm32_i2c_compute_timing().
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The content of Bank Address Register (BAR) is volatile. It is cleared
after power cycle or reset command (RESET F0h).
Some memories (like e.g. s25fl256s) use it to access memory larger than
0x1000000 (16 MiB).
The problem shows up when one:
1. Reads/writes/erases memory > 16 MiB
2. Calls "reset" u-boot command (which is not causing BAR to be cleared)
In the above scenario, the SoC ROM sends 0x000000 address to read SPL.
Unfortunately, the BA24 bit is still set and hence it receives content
from 0x1000000 (16 MiB) memory address.
As a result the SoC aborts and we hang. Only power cycle can take the
SoC out of this state.
How to reproduce/test:
sf probe; sf erase 0x1200000 0x800000; reset
sf probe; sf erase 0x1200000 0x800000; sf write 0x11000000 0x1200000 0x800000; reset
sf probe; sf read 0x11000000 0x1200000 0x800000; reset
Signed-off-by: Lukasz Majewski <lukma@denx.de>
[Fixed comment text on clean_bar function]
Signed-off-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The sunxi-specific SPI load routine only knows how to load a legacy
U-Boot image.
Teach it how to handle FIT images as well, simply by providing the
existing SPL FIT loader with the right loader routine to access the SPI
NOR flash.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Peter Kosa <kope@madnet.sk>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-09-27 12:45:32 +05:30
12169 changed files with 465152 additions and 206125 deletions
HAVE_SPHINX:=$(shell if which $(SPHINXBUILD) >/dev/null 2>&1;thenecho 1;elseecho 0;fi)
ifeq($(HAVE_SPHINX),0)
.DEFAULT:
$(warning The '$(SPHINXBUILD)'command was not found. Make sure you have Sphinx installed and in PATH, or set the SPHINXBUILD make variable to point to the full path of the '$(SPHINXBUILD)' executable.)
@echo
@./scripts/sphinx-pre-install
@echo " SKIP Sphinx $@ target."
else# HAVE_SPHINX
# User-friendly check for pdflatex
HAVE_PDFLATEX:=$(shell if which $(PDFLATEX) >/dev/null 2>&1;thenecho 1;elseecho 0;fi)
sys.stderr.write('Warning: The Sphinx \'sphinx_rtd_theme\' HTML theme was not found. Make sure you have the theme installed to produce pretty HTML output. Falling back to the default theme.\n')
# Theme options are theme-specific and customize the look and feel of a theme
# further. For a list of options available for each theme, see the
# documentation.
#html_theme_options = {}
# Add any paths that contain custom themes here, relative to this directory.
#html_theme_path = []
# The name for this set of Sphinx documents. If None, it defaults to
# "<project> v<release> documentation".
#html_title = None
# A shorter title for the navigation bar. Default is the same as html_title.
#html_short_title = None
# The name of an image file (relative to this directory) to place at the top
# of the sidebar.
#html_logo = None
# The name of an image file (within the static path) to use as favicon of the
# docs. This file should be a Windows icon file (.ico) being 16x16 or 32x32
# pixels large.
#html_favicon = None
# Add any paths that contain custom static files (such as style sheets) here,
# relative to this directory. They are copied after the builtin static files,
# so a file named "default.css" will overwrite the builtin "default.css".
html_static_path=['sphinx-static']
html_context={
'css_files':[
'_static/theme_overrides.css',
],
}
# Add any extra paths that contain custom files (such as robots.txt or
# .htaccess) here, relative to this directory. These files are copied
# directly to the root of the documentation.
#html_extra_path = []
# If not '', a 'Last updated on:' timestamp is inserted at every page bottom,
# using the given strftime format.
#html_last_updated_fmt = '%b %d, %Y'
# If true, SmartyPants will be used to convert quotes and dashes to
# typographically correct entities.
#html_use_smartypants = True
# Custom sidebar templates, maps document names to template names.
#html_sidebars = {}
# Additional templates that should be rendered to pages, maps page names to
# template names.
#html_additional_pages = {}
# If false, no module index is generated.
#html_domain_indices = True
# If false, no index is generated.
#html_use_index = True
# If true, the index is split into individual pages for each letter.
#html_split_index = False
# If true, links to the reST sources are added to the pages.
#html_show_sourcelink = True
# If true, "Created using Sphinx" is shown in the HTML footer. Default is True.
#html_show_sphinx = True
# If true, "(C) Copyright ..." is shown in the HTML footer. Default is True.
#html_show_copyright = True
# If true, an OpenSearch description file will be output, and all pages will
# contain a <link> tag referring to it. The value of this option must be the
# base URL from which the finished HTML is served.
#html_use_opensearch = ''
# This is the file name suffix for HTML files (e.g. ".xhtml").
#html_file_suffix = None
# Language to be used for generating the HTML full-text search index.
/* Zero the one and only argument of "board_init_f" */
mov_s%r0, 0
jboard_init_f
blboard_init_f
/* We only get here if relocation is disabled by GD_FLG_SKIP_RELOC */
/* Make sure we don't lose GD overwritten by zero new GD */
mov %r0, %r25
mov %r1, 0
bl board_init_r
ENDPROC(_start)
/*
Some files were not shown because too many files have changed in this diff
Show More
Reference in New Issue
Block a user
Blocking a user prevents them from interacting with repositories, such as opening or commenting on pull requests or issues. Learn more about blocking a user.
