These frequency calculations depend on the RCW format, which is not
dependent on any particular board. Switch to using ARCH symbols instead
of TARGET.
This whole function could probably use less ifdefs, but for now just do
a minimal conversion.
Fixes: 24cb6f2295 ("fsl-layerscape: Add fsl_esdhc peripheral clock support")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds an SFP binding for the processors it is present on. I have
only tested this for the LS1046A.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
QorIQ platforms now use different clock bindings. Although we don't use
the device tree for clocks on this platform, it is helpful to sync it
because then the bindings will more closely match Linux. Additionally,
it allows for using more clock fractions (such as platform/4).
This corresponds to Linux commit b6f5e7019391 ("ARM: dts: ls1021a:
update the clockgen node").
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Replace reference to the correct name STMicroelectronics
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Depending on backup register value, U-Boot SPL maintains the debug unit
powered-on for debugging purpose; only BUCK1 is required for powering
the debug unit, so revert the setting for all the other power lanes,
except BUCK3 that has to be always on.
To be functional this patch requires a modification in the debugger
,openocd for example, to update the STM32MP15 backup register when it is
required to debug SPL after reset. After deeper analysis this behavior
will be never supported in tools so the associated code, will be never
used and the associated code can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of STM32MP13x the ETZPC part of fdt.c
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: If2777fbf66b8525a2a447056780aaa04e6b0a9a0
Introduce STM32MP15 function and defines to prepare the
STM32MP13 introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Change-Id: I909b205e73dcf207e0216aae5905c3c52472020e
Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
The freeze controller is required for FPGA partial reconfig.
This node is disable on default.
Enable this node via u-boot fdt command when needed.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Override __udelay() as 'always inlined' function so that PSCI code
run in '__secure' section can call this delay function as well.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Dinesh Maniyam <dinesh.maniyam@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add support of several MAC address in OTP (3 32bits OTP word for
2 MAC address) for SOCs in STM32MP13x family: STM32MP133 and STM32MP135.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Introduce the code in mach-stm32mp and the configuration file
stm32mp13_defconfig for the new STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add config CONFIG_STM32MP15_PWR to handle the
access to regulators managed by the PWR driver defined in
pwr_regulator.c
This driver is only used in U-Boot by STM32MP15x family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add sub Kconfig for each SOC in the STM32 CPU family.
It is a preliminary step to introduce a new SOC in the STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add mandatory choice for SOC support in ARCH_STM32MP.
This patch is a preliminary step for new SOC introduction
in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move code and defines only needed for CONFIG_STM32MP15x in stm32mp15x.c
when low level init without TFABOOT is supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
As the get_otp() helper function in bsec are common for all STM32MP family,
move this function in bsec driver
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SPL is only supported by STM32MP15x not by all the
SOC with STM32MP arch.
Only TFABOOT is supported in next products.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add initial support of STM32MP13 family based on v5.18-rc2
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for SPI2 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for CAN1 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART5 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART4 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add another mux option for UART3 pins, this is used on DRC Compact board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The third parameter of dfu_alt_add(), the string description of alternate,
is build in stm32prog_alt_add() with a unnecessary character ';' at the
end of the string.
This separator was required in the first implementation of
dfu_alt_add() but is no more needed in the current implementation;
this separator is managed only in dfu_config_interfaces() which call
dfu_alt_add() for this parameter without this separator.
And since the commit 53b406369e ("DFU: Check the number of arguments
and argument string strictly"), this added character cause an error when
the stm32prog command is executed because the third parameter of
dfu_alt_add() must be a string with a numerical value; 's' must be NULL
in the result of call in dfu_fill_entity_mmc():
third_arg = simple_strtoul(argv[2], &s, 0);
Fixes: 53b406369e ("DFU: Check the number of arguments and argument string strictly")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Currently get_tcr() takes an "el" parameter, to select the proper
version of the TCR_ELx system register.
This is problematic in case of the Apple M1, since it runs with
HCR_EL2.E2H fixed to 1, so TCR_EL2 is actually using the TCR_EL1 layout,
and we get the wrong version.
For U-Boot's purposes the only sensible choice here is the current
exception level, and indeed most callers treat it like that, so let's
remove that parameter and read the current EL inside the function.
This allows us to check for the E2H bit, and pretend it's EL1 in this
case.
There are two callers which don't care about the EL, and they pass 0,
which looks wrong, but is irrelevant in these two cases, since we don't
use the return value there. So the change cannot affect those two.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
With the move to use DM_CLK the boards uart stops working. The used
properties are not supported by the imx8mq clock driver. Thus
the correct baudrate cannot be selected. Remove this properties here and
the board can start with working uart. Keep it in the main dts because
linux handles these porperties fine.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Without this register unlock it is not possible to configure the
pinmux used for mcu spi0.
Fixes: 92e46092f2 ("arch: arm: mach-k3: am642_init: Probe ESM nodes")
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This new MMC sample select value is obtained from running
tests on multiple Stratix 10 boards and proven working.
Signed-off-by: Yau Wai Gan <yau.wai.gan@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Mark wdog1/pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Cubox has an unstable phy address - which can appear at either
address 0 (intended) or 4 (unintended).
SoM revision 1.9 has replaced the ar8035 phy with an adin1300, which
will always appear at address 1.
Change the reg property of the phy node to the magic value 0xffffffff,
which indicates to the generic phy driver that all addresses should be
probed. That allows the same node (which is pinned by phy-handle) to match
either the AR8035 PHY at both possible addresses, as well as the new one
at address 1.
Also add the new adi,phy-output-clock property for enabling the 125MHz
clock used by the fec ethernet controller, as submitted to Linux [1].
Linux solves this problem differently:
For the ar8035 phy it will probe both phy nodes in device-tree in order,
and use the one that succeeds. For the new adin1300 it expects U-Boot to
patch the status field in the DTB before booting
While at it also sync the reset-delay with the upstream Linux dtb.
[1] https://patchwork.kernel.org/project/netdevbpf/patch/20220428082848.12191-4-josua@solid-run.com/
Signed-off-by: Josua Mayer <josua@solid-run.com>
The generated flash.bin does not boot the imx8mn evk LPDDR4 variant
as it misses the spl.bin description in binman.
Add its entry to fix the boot on the imx8mn evk LPDDR4 variant.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Arti Zirk <art@zirk.me>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Add new lines for error messages to make them easier to read.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Add basic support for AM62 SK. This has 2GB DDR.
Note that stack for R5 SPL is in OCRAM @ 0x7000ffff so that is away from
BSS and does not step on BSS section
Add only the bare minimum required to support UART and SD.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce autogenerated SoC data support clk and device data for the
AM62. Hook it upto to power-domain and clk frameworks of U-Boot.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The AM62 SoC family is the follow on AM335x built on K3 Multicore SoC
architecture platform, providing ultra-low-power modes, dual display,
multi-sensor edge compute, security and other BOM-saving integration.
The AM62 SoC targets broad market to enable applications such as
Industrial HMI, PLC/CNC/Robot control, Medical Equipment, Building
Automation, Appliances and more.
Some highlights of this SoC are:
* Quad-Cortex-A53s (running up to 1.4GHz) in a single cluster.
Pin-to-pin compatible options for single and quad core are available.
* Cortex-M4F for general-purpose or safety usage.
* Dual display support, providing 24-bit RBG parallel interface and
OLDI/LVDS-4 Lane x2, up to 200MHz pixel clock support for 2K display
resolution.
* Selectable GPUsupport, up to 8GFLOPS, providing better user experience
in 3D graphic display case and Android.
* PRU(Programmable Realtime Unit) support for customized programmable
interfaces/IOs.
* Integrated Giga-bit Ethernet switch supporting up to a total of two
external ports (TSN capable).
* 9xUARTs, 5xSPI, 6xI2C, 2xUSB2, 3xCAN-FD, 3x eMMC and SD, GPMC for
NAND/FPGA connection, OSPI memory controller, 3xMcASP for audio,
1x CSI-RX-4L for Camera, eCAP/eQEP, ePWM, among other peripherals.
* Dedicated Centralized System Controller for Security, Power, and
Resource Management.
* Multiple low power modes support, ex: Deep sleep,Standby, MCU-only,
enabling battery powered system design.
AM625 is the first device of the family. Add DT bindings for the same.
More details can be found in the Technical Reference Manual:
https://www.ti.com/lit/pdf/spruiv7
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The node name of the bus in the device tree has changed. Also, the length
argument to be passed should be the length of new value. Therefore, fix the
path to usb device tree node as well as the length argument passed.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
For dfu boot mode, the clocks property needs to be deleted and dr_mode
needs to be set to peripheral. Therefore, add the required fixes for the
same.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Add wkup_gpio pinmux setting which will be used for performing the
DT fixup for hbmc node according to mux selection state, on J721E
EVM, hypermux sel is tied to ·WKUP_GPIO0_8.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Add DT node for HyperBus Memory Controller and hbmc-mux in the
FSS. hbmc-am654 driver uses syscon_get_regmap() call which fails
with current compatible setting.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
This uses the nvmem API to load a mac address from an RTC.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This uses an i2c eeprom to load a mac address using the nvmem interface.
Enable I2C_EEPROM for sandbox SPL since it is the only sandbox config
which doesn't enable it eeprom.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This prevents some conflicts when running sandbox with -D, since the
"rom" mac address will be random and won't match the environment. We
still need to keep addresses for eth1 and eth6 in the environment,
because dm_test_eth_rotate expects to be able to disable them by
removing their envaddr variables. This can likely be fixed in a future
series by adding a function to cause sandbox eth_opts callback for a
particular mac to fail immediately.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of reading a pseudo-rom mac address from the device tree, just use
whatever we get from write_hwaddr. This has the effect of using the mac
address from the environment (or from the device tree, if it is
specified).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ramon Fried <rfried.dev@gmail.com>
CONFIG_VAL(DEBUG_UART_BASE) expands to CONFIG_DEBUG_UART_BASE or
CONFIG_SPL_DEBUG_UART_BASE or CONFIG_TPL_DEBUG_UART_BASE and allows boards
to set different values for SPL, TPL and U-Boot Proper.
For ns16550 driver this support is there since commit d293759d55
("serial: ns16550: Add support for SPL_DEBUG_UART_BASE").
Signed-off-by: Pali Rohár <pali@kernel.org>
Update the way KWB_CFG_SEC_BOOT_DEV is determined to use
CONFIG_MVEBU_SPL_BOOT_DEVICE_{SPI,MMC} instead of
CONFIG_SPL_BOOT_DEVICE.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
In some cases, when we don't use CONFIG_SPL_FRAMEWORK nor are we on
PowerPC using their specific SPL/TPL framework, we need to specify the
start.S file to use for these typically very constrained systems. Do
this within the Makefile logic, rather than introducing a string-based
CONFIG option, as this would get slightly complex to do in Kconfig for a
very limited number of users.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
board config header files.
Signed-off-by: Tom Rini <trini@konsulko.com>
In the places where PowerPC references CONFIG_SYS_GBL_DATA_OFFSET it
does so as (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET). And
it defines CONFIG_SYS_GBL_DATA_OFFSET in the same manner that other
architectures define CONFIG_SYS_INIT_SP_OFFSET. Other architectures
define CONFIG_SYS_INIT_SP_ADDR as (CONFIG_SYS_INIT_RAM_ADDR +
CONFIG_SYS_INIT_SP_OFFSET) typically. Rename things within PowerPC for
consistency with other architectures.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently, since we know that in the combination of
CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET all of the "high"
bits are in CONFIG_SYS_INIT_RAM_ADDR and "low" bits are in
CONFIG_SYS_GBL_DATA_OFFSET we reference this separately in start.S, but
added together everywhere else. For clarity consistency, reference the
combined value here instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
The definition of CONFIG_SPL_BOOTROM_SAVE is always a fixed
CONFIG_SPL_STACK + 4, while CONFIG_SPL_STACK is not constant. This
change will make it clear where the location is still, once
CONFIG_SPL_STACK moves to Kconfig.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of PowerPC platforms define this, for SPL. To move this to
Kconfig, it needs to be CONFIG_SPL_SYS_CCSR_DO_NOT_RELOCATE, so use
CONFIG_IS_ENABLED() to check for usage. A number of layerscape
platforms bring this logic from PowerPC, but only need a small part of
it, for the fman driver. Remove their unused portion at least.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_PAD_TO
CONFIG_SPL_MAX_SIZE
CONFIG_TPL_PAD_TO
CONFIG_TPL_MAX_SIZE
Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the
existing places.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_INIT_MINIMAL
CONFIG_SPL_FLUSH_IMAGE
CONFIG_SPL_SKIP_RELOCATE
Signed-off-by: Tom Rini <trini@konsulko.com>
This is always defined to 2, and referenced in two places. Move the
define to <asm/omap_common.h> and make sure the code that uses this
includes that file. Make <asm/arch-omap*/clock.h> not include that
file, as we don't need to be doing so.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the power domain driver default select CONFIG_CLK, so we will
meet lots failures without CLK_IMX8MQ, so default select it.
Fixes: commit 4eb82c2e56 ("imx: power-domain: Get rid of SMCCC dependency")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The AArch64 TCR_ELx register is a 64-bit register, and many newer
architecture features use bits in the upper half. So far U-Boot was
igorant of those bits, trying to leave them alone.
However, in an effort to set bit 31 to 1, it failed doing so, because
the compiler sign-extended "1 << 31", so that all bits[63:31] got set.
Older ARMv8.0 cores don't define anything dangerous up there, but newer
architecture revisions do, and setting all those bits will end badly:
=================
$ qemu-system-aarch64 -cpu max ....
U-Boot 2022.07-rc1 (May 09 2022 - 15:21:00 +0100)
DRAM: 1.5 GiB
================= (hangs here)
Defining TCR_ELx_RSVD to "1U << 31" avoids the sign-extension, so all
upper bits stay at a safe 0 value. This means no more surprises when
U-Boot runs on a more capable CPU core.
Reported-by: Balaji Anandapadmanaban <Balaji.Anandapadmanaban@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Peter Collingbourne <pcc@google.com>
Reviewed-by: Peter Collingbourne <pcc@google.com>
Since commit dffdb1f8eb ("board: ti: am64x: Use fdt functions
for ram and bank init") ddr_init() and dram_bank_init() have
switched to fdtdec for getting the memory configuration from
the am64xx dts files instead of using hardcoded values. This
requires an accessible memory node in SPL as we already have
in k3-am642-r5-evm.dts.
Make the memory node accessible in A53 SPL for both am642-sk
and am642-evm and in am642-sk R5 SPL.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Clean up asm/io.h by
- removing commented code
- removing outdated comments
- removing unused definitions (for mem_isa, mem_pci)
This massively improves the readability of the file.
Suggested by commits:
7ab2e47d27 ("arm: Clean up asm/io.h")
909d0399a5 ("ARM: asm/io.h: kill off confusing #ifdef __mem_pci block")
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Commit ba1ed5b022 ("Convert CONFIG_ARCH_MAP_SYSMEM to Kconfig") clearly
defined that this option is available for SANDBOX (was also for already
removed NDS32). That's why there is no way how this code can be enabled
with current Kconfig layout for riscv.
Based on this removing this code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYo4bYwAKCRDKSWXLKUoM
IYmTAJ9t4GDXggJ7ErB3Kk7/qSrywjEGAgCgnKQVgQvjo1B6o5aiwbk1wR86zkQ=
=W7X8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc4' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc4
zynqmp:
- Fix DP PLL configuration for zcu102/zcu106 and SOM
- Fix split mode for starting R5s
- DT fixes
- Remove firmware node for mini configurations
- Wire TEE for multi DTB fit image
xilinx:
- Handle board_get_usable_ram_top(0) properly
phy:
- Extend psgtr timeout
mmc:
- Fix mini configuration which misses zynqmp_pm_is_function_supported()
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
ARCH_SUNXI selects DM_SERIAL, so the condition can never be satisfied.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When CONFIG_UART0_PORT_F is defined, we try to configure two PortF pins
(usually used for the SD card) as UART0. Some SoCs use the mux value of
3 for this, while others use 4.
The combination of Kconfig symbols we currently use was not quite right:
we mis-configure the A31, A64, H6 and H616.
Going through the list in the pinctrl driver, there are only a few older
SoCs that use a value of 4, so revert the #ifdef clause, and name those
explicitly, instead of the other way around.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Use the de10-nano files as templates for the de10-standard board.
The files in qts directory are generated by quartus from the GHRD
design.
Signed-off-by: Humberto Naves <hsnaves@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This would prevent configuring non-secure regs in case gic security
extensions are not emulated in Qemu.
Signed-off-by: Sai Pavan Boddu <sai.pavan.boddu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Commit e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
fixed SD card booting on mpc85xx boards but broke NOR booting on these
boards. Reason is that U-Boot build system for NOR images uses binman and
this binman ignores alignment defined in linker script. Instead it has own
config file where is alignment defined.
Fix binman alignment for mpc85xx boards to match what is _now_ defined in
linker script.
This change fixes building of U-Boot for NOR booting on P2020 board.
Fixes: e8c0e0064c ("powerpc: mpc85xx: Fix CONFIG_OF_SEPARATE support")
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The initial U-Boot F1C100s port was based on the mainline kernel DT
files, which were quite basic and were missing the essential MMC and
SPI peripherals. While we could work around this in the SPL by
hardcoding the required information, this left U-Boot proper without SD
card or SPI flash support, so actual loading would require FEL boot.
Now the missing DT bits have been submitted and accepted in the kernel
tree, so lets sync back those files into U-Boot to enable MMC and
SPI, plus benefit from some fixes.
This is a verbatim copy of the .dts and .dtsi file from
linux-sunxi/dt-for-5.19[1], which have been part of linux-next for a
while as well.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux.git/log/?h=sunxi/dt-for-5.19
Link: https://lore.kernel.org/linux-arm-kernel/20220317162349.739636-1-andre.przywara@arm.com/
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Copy the devicetree source for the H6 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This commit also adds the following new board devicetrees:
- sun50i-h6-pine-h64-model-b.dts
- sun50i-h6-tanix-tx6-mini.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A64 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree for the R40/T3 SoC verbatim from the Linux v5.18-rc1
tag. None of the existing boards had any devicetree updates.
This commit adds the following new board devicetrees:
- sun8i-r40-oka40i-c.dts
- sun8i-t3-cqa3t-bv3.dts
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the V3(s)/S3 SoCs and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun8i-s3-elimo-initium.dts
- sun8i-v3-sl631-imx179.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds the following new board devicetree:
- sun8i-h3-nanopi-r1.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A83T SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
As with the other SoCs, updates of note include adding detection GPIO
properties in the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A80 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetree:
- sun4i-a10-topwise-a721.dts
While this update should not impact any existing U-Boot functionality,
the changes to the USB PHY detection GPIO properties are needed to
convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A20 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun7i-a20-haoyu-marsboard.dts
- sun7i-a20-linutronix-testbox-v2.dts
- sun7i-a20-olinuxino-lime-emmc.dts
This update includes changes to the USB PHY detection GPIO properties
which are needed to convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix Mele M5 U-Boot only DT]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add a u-boot dtsi for configuring the FEC node of the DH DRC02.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Add a u-boot dtsi for configuring the FEC node of the DH picoITX.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Firstly the FEC can now use the regulator reg_eth_vio from
imx6qdl-dhcom-som.dtsi instead of defining its own.
Secondly the &fec node is moved to the more generic SoM device tree
file, because it can be used by multiple boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH picoITX device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
In the DH electronics iMX6 board file fix the outdated eeprom path by
using a DT label instead.
The label has been newly created for all iMX6QDL DHCOM boards.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
The badblock should be skipped properly in reading and writing.
Fix the logic. The bcb struct is written, skipping the bad block,
so we need to read using the same logic. This was tested create
bad block in the area and then flash it and read it back.
Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
implement get f/w version api.
print ele f/w version in spl.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@nxp.com>
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,
The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Marked related nodes as u-boot,dm-spl for serial driver model
Enable CONFIG_DM_SERIAL
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move some common changes to imx8mq-u-boot.dtsi, so others could reuse it
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The MaxLinear GPY111 PHY is being used on some boards due to part
availability. Add support for this PHY which requires a longer reset
post-delay and RGMII delay configuration.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
To i.MX8, M core stack is pre-coded in source code, so need to get it
before kicking M core. The stack pointer is stored in the first word of
the first PT_LOAD section __isr_vector. So use a num to index the
section loading.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
I was trying to employ lpddr4_mr_read() to something similar to what
the imx8mm-cl-iot-gate board is doing for auto-detecting the RAM
type. However, the version in drivers/ddr/imx/imx8m/ddrphy_utils.c
differs from the private one used by that board in how it extracts the
byte value, and I was only getting zeroes. Adding a bit of debug
printf'ing gives me
tmp = 0x00ffff00
tmp = 0x00070700
tmp = 0x00000000
tmp = 0x00101000
and indeed I was expecting a (combined) value of 0xff070010 (0xff
being Manufacturer ID for Micron). I can't find any documentation that
says how the values are supposed to be read, but clearly the iot-gate
definition is the right one, both for its use case as well as my
imx8mp-based board.
So lift the private definition of lpddr4_mr_read() from the
imx8mm-cl-iot-gate board code to ddrphy_utils.c, and add a declaration
in the ddr.h header where e.g. get_trained_CDD() is already declared.
This has only been compile-tested for the imx8mm-cl-iot-gate
board (since I don't have the hardware), but since I've merely moved
its definition of lpddr4_mr_read(), I'd be surprised if it changed
anything for that board.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tested-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base
address. Convert all board configurations to this new macro. This is the
first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a
clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable
range. The test works such that it multiplies constant N by constant
double-negation of size of a non-empty structure, i.e. it multiplies
constant N by constant 1 in each successful compilation case.
The non-empty structure may contain C11 _Static_assert(), make use of
this and place the kernel variant of static assert in there, so that
it performs the compile-time check for N in the correct range. Note
that it is not possible to directly use static_assert in compound
statements, hence this convoluted construct.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The I2C2 has SMBus device SMSC USB2514Bi connected to it, the device is
capable of up to 100 kHz operation. Reduce the bus frequency to 100 kHz
to guarantee this I2C device can work correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.
Specify the environment location when booting from USB.
Tested on a imx8mn-evk.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
The Avenger96 board comes in multiple regulator configurations.
- rev.100 or rev.200 have Buck3 preconfigured to 3V3 operation on
boot and contains extra Enpirion EP53A8LQI DCDC converter which
supplies the IO. Reduce Buck3 voltage to 2V9 to not waste power.
- rev.200L have Buck3 preconfigured to 1V8 operation and have no
Enpirion EP53A8LQI DCDC anymore, the IO is supplied from Buck3.
Configure the Buck3 voltage on this board per PMIC NVM settings and
update buck3 voltage limits in DT passed to OS before booting OS to
prevent potential hardware damage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
BTN_MISC looks like the most reasonable option for this button.
Button is used by firmware to indicate (after reset, power up) that user
wants to do firmware upgrade via firmware update utility.
For bootloader or OS is this just user button which is worth to have it
mapped.
Also button can be used as a wakeup source and pressing it for more time
can generate more chars that's why also adding wakeup-source and autorepeat
properties.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/7f6d627473632c3c3036ec9f6aaa36e00f4615e2.1652262769.git.michal.simek@amd.com
SGMII requires phy to be configured. The support for this has been added to
Linux and U-Boot already that's why also describe the phy via DT. Clock is
coming from si5332 chip (output 1) 125MHz which is only one GT line use on
this board.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8ad8d0c2fc9690cc90f95feddf87b0e94a685a43.1652262769.git.michal.simek@amd.com
OPP table name now should start with "opp-table" and OPP entries
shouldn't contain commas and @ signs in accordance to the new schema
requirement.
The same change was done in Linux by commit c6d4a8977598 ("ARM: tegra:
Rename CPU and EMC OPP table device-tree nodes"), commit ffbe853a3f5a
("ARM: dts: sunxi: Fix OPPs node name") or commit b7072cc5704d ("arm64:
dts: qcom: qcs404: Rename CPU and CPR OPP tables").
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a1176349448df35127dbac15c1eeb2229505bae7.1652262769.git.michal.simek@amd.com
In all the ZynqMP boards dts files tx-buswidth is by default set to 1. Due
to this the framework only issues 1-1-1 write commands to the GQSPI driver.
But the GQSPI controller is capable of handling 1-4-4 write commands, so
updated the tx-buswidth to 4 in ZynqMP boards dts files. This would enable
the spi-nor framework to issue 1-4-4 write commands instead of 1-1-1. This
will increase the tx data transfer rate, as now the tx data will be
transferred on four lines instead on single line.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/ad61199f55e5e00f29de6206d9d1872a52a7657e.1652193179.git.michal.simek@amd.com
This patch fixes two issues in the set_r5_reset function.
1. When in split mode, the lpd_amba_rst bit should only be set when
both r5 cpu cores are in reset. Otherwise, if one r5 core is still
running, setting the lpd_amba_rst bit will cause an error for the
running core. The set_r5_reset function has been modified to check
if the other r5 core is still running before setting the lpd_amba_rst
bit.
2. The cpu_disable function was always assuming that the r5 cores
are in split mode when resetting either core 4 or 5. This is
incorrect for lockstep functionality. This patch adds a function
check_r5_mode to handle the cpu_disable function correctly for
the r5 cores by checking the mode and handling the reset appropriately.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d99cbd7f2394ac055ef27457298f554ff0747ba7.1651648344.git.michal.simek@amd.com
Moving of internal registers from INTREG_BASE_ADDR_REG to SOC_REGS_PHY_BASE
needs to be done very early, prior calling any function which may touch
internal registers, like debug_uart_init().
So do it earlier in arch_very_early_init() instead of arch_cpu_init().
Movement is done in proper U-Boot, not in SPL. SPL may return to bootrom
and bootrom requires internal registers at (old) expected location.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When this option is set then ARM _main() function would call
arch_very_early_init() function at the beginning. It would be before
calling any other functions like debug_uart_init() and also before
initializing C runtime environment.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Nothing selects ARMADA_64BIT. Instead the 64-bit SoCs just select ARM64
directly. Remove the unused config item.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
-----BEGIN PGP SIGNATURE-----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=s7xn
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220510' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add new STM32 MCU boards and Documentation
STM32 programmer improvements
video: support several LTDC HW versions and fix data enable polarity
board: fix stboard error message, consider USB cable connected when boot device is USB
configs: stm32mp1: set console variable for extlinux.conf
configs: stm32mp1: add support for baudrate higher than 115200 for ST-Link
ARM: stm32mp: Fix Silicon version handling and ft_system_setup()
phy: stm32-usbphyc: Add DT phy tuning support
arm: dts: stm32mp15: alignment with v5.18
ram: Conditionally enable ASR
mach-stm32mp: psci: retain MCUDIVR, PLL3CR, PLL4CR, MSSCKSELR across suspend
configs: Use TFTP_TSIZE on DHSOM and STMicroelectronics boards
ARM: stm32: Use default CONFIG_TFTP_BLOCKSIZE on DHSOM
pinctrl: stm32: rework GPIO holes management
The Buck3 on DHCOR is used to supply IO voltage. It can output either 3V3
in the default DHCOR configuration, or 2V9 in case of AV96 DHCOR variant
which has extra Empirion DCDC converter in front of the 1V8 IO supply, or
outright 1V8 in case of 1V8 IO DHCOR without the Empirion DCDC converter.
The 2V9 mode in case of AV96 DHCOR variant is used to reduce unnecessarily
high input voltage to the Empirion DCDC converter, so move it into matching
DTSI to stop confusing users.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The SoC seems to lose the values of MCUDIVR, PLL3CR, PLL4CR, RCC_MSSCKSELR
during suspend/resume cycle, cache them and reinstate their values on resume.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Device tree alignment with Linux kernel v5.18-rc2:
- ARM: dts: stm32: Add support for the emtrion emSBC-Argon
(only the pincontrol part)
- ARM: dts: stm32: Drop duplicate status okay from DHCOM gpioc node
- ARM: dts: stm32: add st,stm32-sdmmc2 compatible on stm32mp151
- ARM: dts: stm32: fix AV96 board SAI2 pin muxing on stm32mp15
- ARM: dts: stm32: use exti 19 as main interrupt to support RTC wakeup on
stm32mp157
- ARM: dts: stm32: add DMA configuration to UART nodes on stm32mp151
- ARM: dts: stm32: keep uart4 behavior on *
- ARM: dts: stm32: Correct masks for GIC PPI interrupts on stm32mp15
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle correctly the silicon revision = REV_ID[15:0] of Device Version
and the associated device marking, A to Z on STMicroelectronics STM32MP
SOCs.
This patch prepare the introduction of next STM32MP family,
with STM32MP13x Rev.Z for REV_ID = 1.1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The function ft_system_setup shouldn't return an error when the
/soc node is absent in the provided device tree but just skip the
updates.
This patch solves an issue when the U-Boot pytest is executed on board.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Accept flashlayout without header in alternate 0, to simplify
the support of stm32prog command with dfu-util.
By default the flashlayout file size is the size of the received binary,
provided with the offset in the DFU alternate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Update the stm32prog command to allow the reception of U-Boot script in
the FlashLayout alternate during the first USB enumeration.
This patch is aligned with the last TF-A behavior: the Flashlayout
is now loaded by U-Boot; it is no more present at STM32_DDR_BASE when
the stm32prog is launched after a serial boot, on UART or on USB.
The received script must be a U-Boot legacy image, no more need to add
a stm32image header.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
When an interruption is received during the first USB enumeration
used to received the FlashLayout, with handle ctrl-c, the second
enumeration is not needed and the result for stm32prog_usb_loop
is false (reset is not needed).
This patch avoids the need of a second ctrl to interrupt the command
stm32prog.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of UUID for FIP parttion, required by Firmware update
support in TF-A:
- UUID TYPE for FIP partition: 19d5df83-11b0-457b-be2c-7559c13142a5
- "fip-a" partition UUID: 4fd84c93-54ef-463f-a7ef-ae25ff887087
- "fip-b" partition UUID: 09c54952-d5bf-45af-acee-335303766fb3
This check is done with a new partition type "FIP" associated
at the FIP UUID.
The A/B partition UUID is detected by the partition name:
"fip-a", "fip-b".
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of new header for the STM32IMAGE version V2
in command stm32prog command for STM32MP13x family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
When OP-TEE is used, the SMC for BSEC management are not
available and the PTA provisioning for OTP must be used.
U-Boot opens the session to this PTA and use it for OTP
access.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a configuration flag CONFIG_CMD_STM32PROG_OTP to enable the support of
OTP update in stm32prog command.
This new configuration allows to deactivate this feature for security reason
and it is a preliminary step for support of OPT update with the OP-TEE
provisioning TA.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The E4 revision of the AM64 SKEVM embeds a TPS65219 PMIC,
this adds the PMIC node with the required regulators voltages.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
switch the pin definitions from AM33XX_IOPAD to AM33XX_PADCONF macro
Signed-off-by: Gireesh Hiremath <Gireesh.Hiremath@in.bosch.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With sandbox, U-Boot can be run without a device tree (i.e. no -d or -T
parameter). In this case an empty device tree is created for convenience.
With a recent change this causes an error due to the missing '/binman'
node.
Add this node to avoid the problem, as well as a test that U-Boot can
be run without a device tree.
Fixes: 059df5624b ("arch: Kconfig: imply BINMAN for SANDBOX")
Fixes: https://source.denx.de/u-boot/u-boot/-/issues/11
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to be able to get rid of the non-DM MDIO bus registered in
mvneta driver, start using the DM registered one in Turris MOX board
code.
This also allows us to drop the hack introduced in MOX' -u-boot.dtsi
file.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the Octeon ethernet (BGX) and SFP DT nodes to the NIC23 dts file to
enable ethernet support on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the Octeon ethernet (BGX), SMI and PHY DT nodes to the EBB7304 dts
file to enable ethernet support on this board.
Signed-off-by: Stefan Roese <sr@denx.de>
Call octeon_bootmem_init() earlier in the boot process, so that this
bootmemory infrastructure is already initialized when e.g. the
networking support gets probed.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the newly added C files to the Makefile to enable
compilation. This is done in a separate step, to not introduce build
breakage while adding the single files with potentially missing
externals.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch includes misc changes to already present Octeon MIPS C files
files, which are necessary for the upcoming ethernet support.
The changes are mostly:
- DM GPIO & I2C infrastructure
- Coding style cleanup while reworking of the code
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-range.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-qlm-tables.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko-internal-ports-range.c from 2013 U-Boot. It will be used
by the later added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko3.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pko.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki-resources.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-pki.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ipd.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-ilk.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-global-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa-resource.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fpa.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-fau-compat.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-cmd-queue.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-helper-xaui.c from 2013 U-Boot. It will be used by the later
added drivers to support networking on the MIPS Octeon II / III
platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
