As a preparatory step remove the epdc reference which does not exist in
the Linux upstream device tree and rename the qspi1 reference to qspi as
this is how it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:10.1-6 Label or path
epdc not found
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:29.1-7 Label or path
qspi1 not found
+Error: arch/arm/dts/imx7d-sdb-qspi-u-boot.dtsi:6.1-7 Label or path
qspi1 not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the qspi1 reference to qspi as this is how
it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7-cm.dtb.pre.tmp:96.1-7 Label or path qspi1 not
found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx6ull-colibri-eval-v3.dtb rather than the previous imx6ull-colibri.dtb
and imx6ull-colibri-emmc-eval-v3.dtb rather than the previous
imx6ull-colibri-emmc.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the qspi node with its flash0 label as this
is already in the Linux upstream device tree.
This avoids the following error once synchronised:
+arch/arm/dts/imx6ul-14x14-evk.dtb: ERROR (duplicate_label):
/soc/bus@2100000/spi@21e0000/n25q256a@0: Duplicate label 'flash0' on
/soc/bus@2100000/spi@21e0000/n25q256a@0 and
/soc/bus@2100000/spi@21e0000/flash@0
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
imx6dl-colibri-eval-v3.dtb rather than the previous imx6-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next 20220706.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Apalis Evaluation (carrier) board (e.g.
imx6q-apalis-eval.dtb rather than the previous imx6-apalis.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step make sure to refer to absolute node paths where
labels were removed in Linux upstream.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:3.1-7 Label or path aips1
not found
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:11.1-5 Label or path soc
not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warning:
w+arch/arm/dts/imx6dl-brppt2.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
On AM62x devices, main ESM error event outputs can be routed to
MCU ESM as inputs. So, two ESM device nodes are expected in the
device tree : one for main ESM and another one for MCU ESM.
MCU ESM error output can trigger the reset logic to reset
the device when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is
set to '0'.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Apple's M2 SoC very similar to the M1 and can use the same memory map.
The keyboard/trackpad on the MacBook Pro (13-inch, M2, 2022) uses
"dockchannel" as transport instead of SPI and needs a new driver.
USB, NVMe, uart, framebuffer and watchdog are working with the existing
drivers.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The macro `CONFIG_SYS_UBOOT_BASE` is used by SPL loaders `"NOR"` and
`"XIP"` to determine the base address of u-boot.
For `"NOR"` on i.MX8MM it is the base address of QSPI0 plus the offset
of the flattened image tree blob.
Although `QSPI0_AMBA_BASE` is used to define CONFIG_SYS_UBOOT_BASE in
multiple board header files for i.MX8MM, it is not specified.
Specify offset of flattened image tree blob (needs to be set to same
value as specified in 'binman' node), base address of QSPI0 and size of
FlexSPI configuration block.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Add definition for FSPI configuration block and subsequently new offsets for
u-boot-spl and u-boot-itb for CONFIG_FSPI_HEADER option.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Simplify the use of the ROM API by using the wrappers that take care
of saving/restoring gd and computing the xor value. This makes the
generated code smaller and the C code easier to read.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The ROM API is thoroughly undocumented, but apparently passing the xor
of the real arguments as an extra argument is required [1]. Also, we
need to do the "save gd/restore gd" dance. These are both error-prone,
and lead to a lot of code duplication.
Since both imx8m[np] and imx8ulp SOCs have this, add a separate
translation unit which is included precisely when the new
CONFIG_IMX8_ROMAPI symbol is set, which provide convenience wrappers
that take care of computing the xor value as well as doing the gd
dance, and that thus have a more intuitive API. Subsequent patches
will make use of these to reduce boilerplate.
[1] One wonders, for example, if the check is only applied to the
lower 32 bits, or if we're implicitly relying on all 64-bit pointer
values we're passing effectively have 0 in the upper 32 bits.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This exposes the struct rom_api, the g_rom_api variable declaration
and the associated #defines to slightly fewer boards: namely, those
IMX8M which are not IMX8MN or IMX8MP. But the latter two are the only
IMX8M* ones where the g_rom_api variable is defined (in imx8m/soc.c),
so that should be fine.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order not to repeat the IMX8MN || IMX8MP || IMX8ULP logic in
multiple places where we need to know if the SOC exposes the ROM API,
add a "def_bool y" Kconfig symbol.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- leave tx-delay/rx-delay undefined in dt defaulting to 2.0ns
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Change detection of platform/cpu from runtime to compile time via config
define. This completely eliminates compiling code which is not going to run
on selected platform. Code which parses and prints device / revision id
still reads device id from MVEBU_REG_PCIE_DEVID register, but only once.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
A common external watchdog circuit is kept alive by triggering a short
pulse on the reset pin. This patch adds support for this use case, while
making the algorithm configurable in the devicetree.
The "linux,wdt-gpio" driver being modified is based off the equivalent
driver in the Linux kernel, which provides support for this algorithm.
This patch brings parity to this driver, and is kept aligned with
the functionality and devicetree configuration in the kernel.
It should be noted that this adds a required property named 'hw_algo'
to the devicetree binding, following suit with the kernel. I'm happy to
make this backward-compatible if preferred.
Signed-off-by: Paul Doelle <paaull.git@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
board_get_usable_ram_top() conflated the RAM size with the top address
of RAM. On systems where RAM starts at address 0 these numbers are the
same so it went unnoticed. Update board_get_usable_ram_top() to take
CONFIG_SYS_SDRAM_BASE into account when determining the top address.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This option is used only by the phy-sun4i-usb driver, which does not
inherently depend on the ARM architecture.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
KConfig has range option, use it instead of notice in the option
descrition.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The mt7621_rfb board supports integrated giga PHYs plus one external
giga PHYs. It also has up to 512MiB DDR3, 16MB SPI-NOR, 3 mini PCI-e x1
slots, SDXC and USB.
The mt7621_nand_rfb board is almost the same as mt7621_rfb board, but it
uses NAND flash and SDXC is not available.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek MT7621 SoC.
All files are dedicated for u-boot.
The default build target is u-boot-mt7621.bin.
The specification of this chip:
https://www.mediatek.com/products/homenetworking/mt7621
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for noncached_alloc() which was only supported by
ARM platform.
Unlike the ARM platform, MMU is not used in u-boot for MIPS. Instead, KSEG
is provided to access uncached memory. So most code of this patch is copied
from cache.c of ARM platform, with only two differences:
1. MMU is untouched in noncached_set_region()
2. Address returned by noncached_alloc() is converted using KSEG1ADDR()
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds __image_copy_len needed by TPL of MT7621 SoC.
The __image_copy_len represents the binary blob size of both SPL/TPL
binaries. To achieve this, __text_start/end are added for calculation.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add more definitions needed for MT7621 initialization.
MT7621 needs to initialize GIC/CPC and other related parts.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
To be compatible with old u-boot used by lots of MT7621 devices, the u-boot
needs to boot-up MT7621's all cores, and all VPES of each core.
This patch adds asm/mipsmtregs.h from linux kernel which is need for
boot-up VPEs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmLNj88ACgkQ4rK92eCq
k3Wukwf+PZnmQuyzwwFDOpZO1lUPfUN0WkoEBV8M5IxLehHdfHJT3YsAtm6DS8dd
4+n0+WmR7Uk4B8ODRPrGNBJftFoOVfEAvWmpfCC/VcHgEDEzdJzJe6yxa9wAWeQR
djRZLM8qx6OIEUW+sfYbFkD2BCv+cLiT0YH9qqx8WCRlf6JTuLquSBJQXIJAqYiE
LdO/pp0rv4oC0s08BSL4bHL/Mh7FHeUPiEjn2uRP/vISgmH1qyCql3gbr/wCaTYR
jfqr9pjmWTxEOppZIdE832QMy1MTSA/6Q3Jr4LKRko6ArBGjbGlj3EbeeEdKPDRy
BtQ6OLnxWKdcPr2qp301nnERRi4L4w==
=WgbW
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220712' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Alignment with Linux kernel device tree v5.19 for stm32mp15 and stm32mp13
- Add OP-TEE nodes for stm32mp13x, alligned with upstreamed OP-TEE
- Introduce of_to_plat ops in stm32_sdmmc2 driver
- Activate more features in stm32mp13 defconfig and support of STM32MP13x Rev.Y
- Drop fastboot and stm32prog trigger gpios on STM32MP15x DHCOM board
keystone doesn't have custom gpio.h that's why don't select
GPIO_EXTRA_HEADER which points to it.
Logic in arch/arm/include/asm/gpio.h is very clear
#ifdef CONFIG_GPIO_EXTRA_HEADER
#include <asm/arch/gpio.h>
#endif
#include <asm-generic/gpio.h>
Where it is visible that there is no gpio.h in platform headers:
$ ls arch/arm/mach-keystone/include/mach/
clock_defs.h clock-k2e.h clock-k2hk.h ddr3.h hardware-k2e.h
hardware-k2hk.h i2c_defs.h mon.h mux-k2g.h xhci-keystone.h
clock.h clock-k2g.h clock-k2l.h hardware.h hardware-k2g.h
hardware-k2l.h mmc_host_def.h msmc.h psc_defs.h
Signed-off-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
PA13 and PA14 are used for USB power control and can't be used
to enforce fastboot or stm32prog mode by pressing a button.
Defining CONFIG_FASTBOOT/CONFIG_CMD_STM32PROG without this patch applied
results in fastboot/stm32prog always starting, because PA13/PA14 are always
low during boot. So drop the wrong trigger gpios definitions.
Signed-off-by: Johann Neuhauser <jneuhauser@dh-electronics.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Activate the led managed in stm32mp1 board for U-Boot indication
in STM32MP13F-DK device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of STM32MP13x Rev.Y for the Silicon revision REV_ID = 0x1003.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a "secure" version of STM32 boards based on SCMI when RCC_TZCR.TZEN=1.
Only boards provided by STMicroelectronics are concerned:
-STM32MP157A-DK1
-STM32MP157C-DK2
-STM32MP157C-ED1
-STM32MP157C-EV1
The resources secured by RCC_TZCR.TZEN=1 are managed by OP-TEE
and the associated SCMI services, reset and clock.
These device trees are only supported with stm32mp15_defconfig,
with OP-TEE, SCMI and without SPL support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for SCMI firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the node for OP-TEE firmware with the associated reserved memory nodes
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
We have a single platform that is both in the OMAP3 family of parts, but
has an EMIF4 memory controller. Currently we hard-code the size of
chip select 0. Make this more clear by putting the value in the
function rather than a CONFIG option.
Signed-off-by: Tom Rini <trini@konsulko.com>
With the last platform for this architecture removed, remove the rest of
the architecture support as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_EMIF_PRECALCULATED_TIMING_REGS
CONFIG_SYS_AUTOMATIC_SDRAM_DETECTION
CONFIG_SYS_DEFAULT_LPDDR2_TIMINGS
Signed-off-by: Tom Rini <trini@konsulko.com>
All of these symbols are not referenced anywhere else in the code, so
remove them.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_OHCI_SWAP_REG_ACCESS
CONFIG_SYS_USB_OHCI_CPU_INIT
CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS
CONFIG_SYS_USB_OHCI_SLOT_NAME
CONFIG_USB_ATMEL
CONFIG_USB_ATMEL_CLK_SEL_PLLB
CONFIG_USB_ATMEL_CLK_SEL_UPLL
CONFIG_USB_OHCI_LPC32XX
CONFIG_USB_OHCI_NEW
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The generic arm linker script contains this section:
.bss __rel_dyn_start (OVERLAY) : {
...
}
The (OVERLAY) syntax in the description causes the .bss section to be
included in the NOR area of the image:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
0000c61c l d .bss 00000000 .bss
0000c640 l O .bss 00000040 __value.0
0000c68c g O .bss 00000000 __bss_end
0000c61c g O .bss 00000000 __bss_start
0000c680 g O .bss 0000000c stdio_devices
This is what the custom linker script tries to avoid, as the NOR area is
read-only.
Remove the OVERLAY syntax to fix the BSS location:
$ objdump -t -j .bss spl/u-boot-spl
SYMBOL TABLE:
83000000 l d .bss 00000000 .bss
83000000 l O .bss 00000040 __value.0
0000c61c g O .bss 00000000 __image_copy_end
8300004c g O .bss 00000000 __bss_end
83000000 g O .bss 00000000 __bss_start
83000040 g O .bss 0000000c stdio_devices
This restores the state of the linker script before the patch that fixed
the linker lists issue.
Fixes: f6810b749f ("aspeed/ast2600: Fix SPL linker script")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The EVB has an EEPROM on bus 3 and a LM75 temp sensor on bus 7. Enable
those busses we can test the I2C driver.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
The same as the upstream Linux device tree, each i2c bus has a property
specifying the reset line.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Set the pinctrl groups for each I2C bus. These are essential to
I2C operating correctly.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Mark the memory node with u-boot,dm-spl so we can use it
from early SPL on both R5 and A53.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The spl_enable_dcache() function calls dram_init_banksize()
to get the total memory size. Normally the dram_init_banksize()
setups the memory banks, while the total size is reported
by ddr_init(). This worked so far for K3 since we set the
gd->ram_size in dram_init_banksize() as well.
Signed-off-by: Georgi Vlaev <g-vlaev@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
implement overrides for spl_spi_boot_bus() and spl_spi_boot_cs()
lookup functions according to bootmode selection, so as to support
both QSPI and OSPI boot using the same build.
Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
This converts the following to Kconfig:
CONFIG_KIRKWOOD_EGIGA_INIT
CONFIG_KIRKWOOD_PCIE_INIT
CONFIG_KIRKWOOD_RGMII_PAD_1V8
CONFIG_KM_DISABLE_PCIE
Signed-off-by: Tom Rini <trini@konsulko.com>
As things stand currently, there is only one PowerPC platform that
enables the options for CHAIN_OF_TRUST. From the board header files,
remove a number of never-set options. Remove board specific values from
arch/powerpc/include/asm/fsl_secure_boot.h as well. Rework
include/config_fsl_chain_trust.h to not abuse the CONFIG namespace for
constructing CHAIN_BOOT_CMD. Migrate all of the configurable addresses
to Kconfig.
If any platforms are re-introduced with secure boot support, everything
required should still be here, but now in Kconfig, or requires migration
of an option to Kconfig.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that secure boot is implemented today on NXP ARM platforms does
not reuse the elements found in include/config_fsl_chain_trust.h to
construct CONFIG_SECBOOT but instead board header files have their
environment setup as needed and then fsl_setenv_chain_of_trust() will
set secureboot in the environment. Remove a large number of unused
defines here.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Move setting of SPL_UBOOT_KEY_HASH to a non-NULL value to Kconfig. As
part of this, change fsl_secboot_validate(...) to check that it is
passed a non-empty string, rather than non-NULL.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Make all of the CHAIN_OF_TRUST options be under a single menu and add a
comment for the rest, so the resulting config file reads more clearly.
Remove duplicate CHAIN_OF_TRUST options from
board/congatec/common/Kconfig. Remove duplicate NXP_ESBC config
questions and move to arch/Kconfig.nxp.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KEY_REVOCATION
CONFIG_SYS_FSL_SFP_BE
CONFIG_SYS_FSL_SFP_LE
CONFIG_SYS_FSL_SFP_VER_3_0
CONFIG_SYS_FSL_SFP_VER_3_2
CONFIG_SYS_FSL_SFP_VER_3_4
CONFIG_SYS_FSL_SRK_LE
This partly means making sure to enable SYS_FSL_ERRATUM_A007186 only for
when CHAIN_OF_TRUST is enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_FSL_SEC_MON
CONFIG_SYS_FSL_SEC_MON_BE
CONFIG_SYS_FSL_SEC_MON_LE
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that board/freescale/common/Kconfig is safe to be included once,
globally, rename this to arch/Kconfig.nxp to better reflect that it
contains options that are valid on multiple architectures and SoC
families, and not specific to NXP reference platforms either.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The way that we use this file currently means that we have to guard it
in every platform Kconfig. But it is also required in all NXP
platforms, including non-reference platforms. Make all options in it
have appropriate dependencies so that we can include it a single time
under arch/Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_HETROGENOUS_CLUSTERS
CONFIG_SYS_MAPLE
CONFIG_SYS_CPRI
CONFIG_PPC_CLUSTER_START
CONFIG_DSP_CLUSTER_START
CONFIG_SYS_CPRI_CLK
CONFIG_SYS_ULB_CLK
CONFIG_SYS_ETVPE_CLK
Signed-off-by: Tom Rini <trini@konsulko.com>
We rename the S5P specific "CONFIG_PWM" to CONFIG_PWM_S5P and move it to
Kconfig. Given the usage of CONFIG_PWM_NX, we have that select this new
symbol.
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After more patches code for jumping to _start_cont symbol in flash memory
involved to code with useless mathematical operations. Currently it does:
r3 := CONFIG_SYS_MONITOR_BASE + ABS(_start_cont) - CONFIG_SYS_MONITOR_BASE
jump to r3
Which is equivalent of just:
r3 := ABS(_start_cont)
jump to r3
The purpose of that code is just to jump to _start_code symbol,
independently of program counter. So branch must be done to absolute
address. Trying to write:
ba _start_cont
just cause linker error:
LD u-boot
powerpc-linux-gnuspe-ld.bfd: arch/powerpc/cpu/mpc85xx/start.o: in function `switch_as':
(.bootpg+0x4b8): relocation truncated to fit: R_PPC_ADDR24 against symbol `_start_cont' defined in .text section in arch/powerpc/cpu/mpc85xx/start.o
make: *** [Makefile:1801: u-boot] Error 1
Probably by the fact that absolute address cannot be expressed by 24-bits.
So write the code via mtlr+blr pattern as it was before and load general
purpose register with absolute address of the symbol:
lis r3,_start_cont@h
ori r3,r3,_start_cont@l
mtlr r3
blr
Seems that gcc and gnu ld linker support symbol@h and symbol@l syntax like
number@h and number@l without any problem. And disassembling of compiler
u-boot binary proved that lis+ori instructions are called with numbers
which represent halves of absolute address of _start_cont symbol.
Signed-off-by: Pali Rohár <pali@kernel.org>
DT node pic@40000 is defined explicitly in p2020-post.dtsi file and also
transitionally via include file pq3-mpic.dtsi. Remove duplicate definition
from p2020-post.dtsi.
No change in final DTB file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Before relocating to SDRAM, the ECC is initialized by clearing the
whole SDRAM. In order to speed this up, dcache_enable is used (see
sdram_init_ecc_bits).
Since commit 503eea4519 ("arm: cp15: update DACR value to activate
access control"), this no longer works, because running code in OCRAM
with the XN bit set causes a page fault. Override dram_bank_mmu_setup
to disable XN in the OCRAM and setup DRAM dcache before relocation.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Using udelay while the clocks aren't fully configured causes the timer
system to save the wrong clock rate. Use sdelay and wait_on_value
instead (the values used in these functions were found experimentally).
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
Add defconfig and Kconfig files for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add devicetrees for Google Chameleon V3 board
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Signed-off-by: Alexandru M Stan <amstan@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add handoff headers for the Google Chameleonv3 variants: 480-2 and
270-3. Both files were generated using qts-filter-a10.sh.
Signed-off-by: Paweł Anikiel <pan@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmK9nEUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyEu0B/4v1EQOMBL+VXns8Ipo
Xeq+RDUX/24XcB5s6sTcNlWzvYuX6Z7DCGJ0loK5JxelrOy+YNkRbTRMom1eW9Kn
9dmKa0bcO7auJEww3Nln1IFyx+FXQFGR1V3g1U4535l8b7urTioIK0MUSrG/GLpe
Rlbh31GAYtrGvl06W1F7mwhg7/0AT8IhUFaY9G7s7gKA5muGQQ7ED4nKVoZPeTAl
lrQ/Ecym1ND7aOhd/vuEBtgoGxDWzwf8piT8qykJluJKzBV1Hic0RXCNBmtrTORz
b1GOOpRUgcnTv9U8j4PRyYGKDnmS2OmV2AwL8+V9UJfJgQrkcRlbgpCysIPmMBzo
YPRt
=D79P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.10 cycle:
This feature set includes mostly fixes and alignments: DT alignment with
Linux for sama7g5, removal of invalid eeprom compatibles, removal of
extra debug_uart_init calls for all at91 boards, support for pio4 driver
pioE bank, and other minor fixes and enhancements for sam9x60 and
sama5d2_icp boards.
On versal platform, enable apb linear mode for apb read and write
execute operations amd disable it when using dma reads. This is done by
xilinx_pm_request() secure calls when CONFIG_ZYNQMP_FIRMWARE is enabled,
else we use direct raw reads and writes in case of mini U-Boot.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-5-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
When flash operated at non default mode like DDR, flash need to be reset
to operate in SDR mode to read flash ids by spi-nor framework. Reset the
flash to the default state before using the flash. This reset is handled
by a gpio driver, in case of mini U-Boot as gpio driver is disabled, we
do raw read and write access by the registers.
Versal platform utilizes spi calibration for read delay programming, so
incase by default read delay property is set in DT. We make sure not to
use read delay from DT by overwriting read_delay with -1.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Link: https://lore.kernel.org/r/20220512100535.16364-4-ashok.reddy.soma@xilinx.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Sync the pinebook pro to upstream 5.18, in particular this brings
brings in a fix so the DP is disabled so Linux will actually boot.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For Rockchip boards with the all rk8xx series PMICs (excluding the
rk808), it is sometimes desirable to not boot whenever the device is
plugged in. An example would be for the Odroid Go Advance.
This provides a configurable option to check the PMIC says it was
powered because of a plug-in event. If the value is 1 and this option
is selected, the device shuts down shortly after printing a message
to console stating the reason why it's shutting down. Powering up the
board with the power button is not affected.
This patch parallels the work done in the following patch series:
https://lore.kernel.org/u-boot/20220121133732.2397273-1-andre.przywara@arm.com/
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This commit adds support for the OP-TEE 'tee.bin' v1 format for Rockchip
platforms.
Since OP-TEE 3.8.0, tee.bin contains meta-data in a proprietary format
in addition to the ELF data. They are essential information for proper
initialization of the TEE core, such as the size of the memory region
covered by the TEE or a compact representation of runtime relocation
data when ASLR is enabled.
With OP-TEE 3.8.0 onwards, 'tee.elf' MUST NOT be used and 'tee.bin'
MUST be used instead. Ignoring this recommendation can lead to crashes
as described in [3].
Link: [1] 5dd1570ac5
Link: [2] https://github.com/OP-TEE/optee_os/blob/3.17.0/scripts/gen_tee_bin.py#L275-L302
Link: [3] https://github.com/OP-TEE/optee_os/issues/4542
Signed-off-by: Jerome Forissier <jerome.forissier@linaro.org>
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version move the dma-controller nodes
to the DT root.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to better compare the Linux rk3288.dtsi version
with the u-boot version sort the mipi,hdmi,lvds and dp nodes.
Changed:
Rename mipi_dsi label.
Rename dp nodename.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
With the conversion of rockchip-usb-phy.yaml a long time used fallback
string for rk3066a/rk3188 was added. The linux driver doesn't do much with
the GRF phy address range, however the u-boot driver rockchip_usb2_phy.c
does. The bits in GRF_UOC0_CON2 for rk3066a/rk3188 and rk3288 for example
don't match. Remove the usb-phy fallback string for rk3188
to prevent possible strange side effects.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Change define condition in board_usb_init() function
to allow rk3066/rk3188 to use the USB PHY driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
- In a number of cases, use CONFIG_ARCH_EXYNOS[45] rather than
CONFIG_EXYNOS[45]
- In other cases, test for CONFIG_ARCH_EXYNOS or CONFIG_ARCH_S5PC1XX
- Migrate specific SoC CONFIG values to Kconfig
- Use CONFIG_TARGET_x rather than CONFIG_x
- Migrate other CONFIG_EXYNOS_x symbols to Kconfig
- Reference CONFIG_EXYNOS_RELOCATE_CODE_BASE directly as EXYNOS_RELOCATE_CODE_BASE
- Rename CONFIG_S5P_PA_SYSRAM to CONFIG_SMP_PEN_ADDR to match the rest
of U-Boot usage.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The only use of CONFIG_XTFPGA was to build all of the in-tree device
trees. Switch to using CONFIG_XTENSA instead of a non-Kconfig symbol.
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
We want to keep all of the default values for SPL_LDSCRIPT in the same
place both for overall clarity as well as not polluting unrelated config
files.
Signed-off-by: Tom Rini <trini@konsulko.com>
The commit 99e2fbcb69 ("linker_lists: Rename sections to remove .
prefix") changed the name of the linker list sections. As the Aspeed SPL
linker wasn't in the tree yet, it missed the change.
This updates the SPL linker to match arch/arm/cpu/u-boot-spl.lds which
Aspeed was copied from.
Fixes: 442a69c143 ("configs: ast2600: Move SPL bss section to DRAM space")
Signed-off-by: Joel Stanley <joel@jms.id.au>
Currently CONFIG_SPL_TEXT_BASE and CONFIG_SYS_TEXT_BASE addresses are
manually increased by 0x1000 due to .bootpg section. This section has size
of 0x1000 bytes and is manually put by linker script before .text section
(and therefore before base address) when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Due to this fact lot of other config options are manually increased by
0x1000 value to make correct layout. Note that entry point is not on
CONFIG_SPL_TEXT_BASE (image+0x1000) but it is really on address
CONFIG_SPL_TEXT_BASE-0x1000 (means at the start of the image).
Cleanup handling of .bootpg section when CONFIG_SYS_MPC85XX_NO_RESETVEC is
set. Put .bootpg code directly into .text section and move text base
address to the start of .bootpg code. And finally remove +0x1000 value from
lot of config options. With this removal custom PHDRS is not used anymore,
so remove it too.
After this change entry point would be at CONFIG_SPL_TEXT_BASE and not at
address -0x1000 anymore.
Tested on P2020 board with SPL and proper U-Boot.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
In case rtt_nom is set to 0 keep ODT disabled (MMDC MPODTCTRL = 0).
No changes required for DDR MR1 Rtt_Nom impedance register, 0 value is
already handled correctly.
No board is currently affected by this change (rtt_nom != 0 on all i.MX6
ddr3 boards), this will be used by a follow-up change.
Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fixup thermal trips in Linux device tree according to SoC thermal
grade.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Adam Ford <aford173@gmail.com>
The memory on this board is microchip 24aa025e48 which is compatible with
at24c02 with a page size of 16.
Fix the compatible accordingly.
Reported-by: Sergiu Moga <sergiu.moga@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
microchip,24aa025e48 does not exist in the bindings of this driver.
It can be replaced with atmel,at24c02 which is a standard compatible
and the memory is compatible with this one, depending on the page size.
microchip 24aa02e48 has a page size of 8, while 24aa025e48 has a page
size of 16 bytes.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Michael Walle <michael@walle.cc>
Reviewed-by: Heiko Schocher <hs@denx.de>
Change the compatible of the qspi child node to
`jedec,spi-nor` so that it can be properly found
when probing the bus.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
In arch/arm/lib/sections.c there is below code:
char __image_copy_start[0] __section(".__image_copy_start");
But actually 'objdump -t spl/u-boot-spl' not able to find out
symbol '__image_copy_start' for binman update image-pos/size.
So update link file
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
U-Boot's printf() used before setting up U-Boot's serial driver does not
create any output. Use os_printf() for error messages related to loading
the device-tree.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Before setting up the devices U-Boot's printf() function cannot be used
for console output. Provide function os_printf() to print to stderr.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This patch adds support for the SHA-256 Secure Hash Algorithm for CPUs
that have support for the SHA-256 part of the ARM v8 Crypto Extensions.
It greatly improves sha-256 based operations, about 17x faster on iMX8M
evk board. ~12ms vs ~208ms for a 20MiB kernel sha-256 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
This patch adds support for the SHA-1 Secure Hash Algorithm for CPUs
that have support for the SHA-1 part of the ARM v8 Crypto Extensions.
It greatly improves sha-1 based operations, about 10x faster on iMX8M
evk board. ~12ms vs ~165ms for a 20MiB kernel sha-1 verification.
asm implementation is a simplified version of the Linux version (from
Ard Biesheuvel).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYrlYngAKCRDKSWXLKUoM
ITgbAJ9S9xO2QqxtuodWAYMtJfvZ14c7mgCeKnyFTrrBnJkC0wPsGqE71oNJ49o=
=3gGm
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.10' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.10
cpu:
- Add driver for microblaze cpu
net:
- Add support for DM_ETH_PHY to AXI emac and emaclite
xilinx:
- Switch platforms to DM_ETH_PHY
- DT chagnes in ZynqMP and Zynq
- Enable support for SquashFS
zynqmp:
- Add support for KR260 boards
- Move BSS from address 0
- Move platform identification from board code to soc driver
- Improve zynqmp_psu_init_minimize
versal:
- Enable loading app at EL1
serial:
- Setup default address and clock rates for DEBUG uarts
pinctrl:
- Add support for tri state and output enable properties
relocate-rela:
- Clean relocate-rela implementation for ARM64
- Add support for Microblaze
microblaze:
- Add support for runtime relocation
- Rework cache handling (wiring, Kconfig) based on cpuinfo
- Remove interrupt support
timer:
- Extract axi timer driver from Microblaze to generic location
linux system will die if we offline one of the cpu on R40 based board:
eg: echo 0 > /sys/devices/system/cpu/cpu3/online
The reason is that the R40 version of sunxi_cpu_set_power always passes
0 for the CPU number, so we turn off CPU0, regardless of what CPU the
CPU_OFF request came for.
Fix this by passing the proper CPU number, as there are proper power
clamp registers for every of the four cores.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Copy the devicetree source for the A10 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
The previous version of this change was only partially applied.
Fixes: 4746694cba ("ARM: dts: sun4i: Sync from Linux v5.18-rc1")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Building the sandbox with NO_SDL=1 resulted in an undefined reference to
'sandbox_sdl_remove_display'. Resolve this by adding a stub
implementation to match the stubs of the other similar functions.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
"size-cells" of the nand controller node should be 0 as the "reg"
property of the nand device node contains the chip select number and not
address information.
The patch fixes the below compilation warning
arch/arm/dts/zynq-zc770-xm011.dtb: Warning (reg_format):
/axi/memory-controller@e000e000/nand-controller@0,0/nand@0:reg: property
has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1)
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/6e90665a2dad7fe8ade10b8f57101f8144963791.1655288559.git.michal.simek@amd.com
As per design, all input/rx pins should have fast slew rate and 12mA
drive strength. Rest all pins should be slow slew rate and 4mA drive
strength. Fix usb nodes as per this and remove setting of slow slew rate
for all the usb gorup pins.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b245c165f05845c1f3ab41a92c82b7ec1538cee4.1655288171.git.michal.simek@amd.com
Move axi timer driver from Microblaze to generic location.
Origin implementation was irq based with counting down timer.
CONFIG_TIMER drivers are designed differently that timer is free running up
timer with automatic reload without any interrupt.
Information about clock rates are find out in timer_pre_probe() that's why
there is no need to get any additional information from DT in the driver
itself (only register offset).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Tested-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Link: https://lore.kernel.org/r/6c12fc86bbc1f17d05c25018862e7b7b03346b36.1654684731.git.michal.simek@amd.com
Add a basic CPU driver that retrieves information about the microblaze CPU
core. cpu_ops handlers are implemented so that the "cpu" command can work
properly:
U-Boot-mONStR> cpu list
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
U-Boot-mONStR> cpu detail
0: cpu@0 MicroBlaze @ 50MHz, Rev: 11.0, FPGA family: zynq7000
ID = 0, freq = 50 MHz: L1 cache, MMU
Note: cpu_ver_lookup[] and family_string_lookup[] arrays were imported from
linux.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-14-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add helper code for PVR (Processor Version Register) data handling. It
will be used by the UCLASS_CPU driver to populate cpuinfo fields at
runtime.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-13-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align microblaze with the other architectures and provide an
implementation for flush_dcache_range(). Also, remove the microblaze
exception in drivers/core/device.c.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-11-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Introduce a minimal cpuinfo structure to hold cache related info. The
instruction/data cache size and cache line size are initialized early in
the boot to default Kconfig values. They will be overwritten with data
from PVR/dtb if the microblaze UCLASS_CPU driver is enabled.
The cpuinfo struct was placed in global_data to allow the microblaze
UCLASS_CPU driver to also run before relocation (initialized global data
should be read-only before relocation).
gd_cpuinfo() helper macro was added to avoid volatile
"-Wdiscarded-qualifiers" warnings when using the pointer directly.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-10-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/)
All flush_cache() calls in microblaze code are supposed to flush the
entire instruction and data caches, so introduce flush_cache_all()
helper to handle this.
Also, provide implementations for flush_dcache_all() and
invalidate_icache_all() so that icache and dcache u-boot commands can
work.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-9-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace XILINX_DCACHE_BYTE_SIZE macro with two Kconfig symbols for
instruction and data caches sizes, respectively:
CONFIG_XILINX_MICROBLAZE0_ICACHE_SIZE
CONFIG_XILINX_MICROBLAZE0_DCACHE_SIZE
Also, get rid of the hardcoded value in icache_disable().
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-8-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com> (s/bralid/brlid/g)
Factor out icache/dcache components from flush_cache() function. Call the
newly added __flush_icache()/__flush_dcache() functions inside
icache_disable() and dcache_disable(), respectively. There is no need to
flush both caches when disabling a particular cache type.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-7-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace CONFIG_ICACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WIC. It should be enabled if the processor supports
the "wic" (Write to Instruction Cache) instruction. It will be used to
guard "wic" invocations in microblaze cache code.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-6-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Replace CONFIG_DCACHE with a Kconfig option more limited in scope -
XILINX_MICROBLAZE0_USE_WDC. It should be enabled if the processor supports
the "wdc" (Write to Data Cache) instruction. It will be used to guard
"wdc" invocations in microblaze cache code.
Also, drop all ifdefs around flush_cache() calls and only keep one
CONFIG_IS_ENABLED() guard within flush_cache() itself.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-5-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
XILINX_USE_DCACHE macro was removed in 7556fa09e0 ("microblaze: Simplify
cache handling"), but it was still used in a couple of places.
Replace those occurences with CONFIG_DCACHE.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Link: https://lore.kernel.org/r/20220531181435.3473549-4-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Microblaze is using NEEDS_MANUAL_RELOC from the beginnging. This is causing
issues with function pointer arrays which need to be updated manually after
relocation. Building code with -fPIC and linking with -pic will remove this
limitation and there is no longer need to run manual update.
By default still old option is enabled but by disabling NEEDS_MANUAL_RELOC
code will be compiled for full relocation.
The patch does couple of things which are connected to each other.
- Define STATIC_RELA dependency to call relocate-rela to fill sections.
- REMAKE_ELF was already enabled but u-boot file can't be used because
sections are empty. relocate-rela will fill them and output file is
u-boot.elf which should be used.
- Add support for full relocation (u-boot.elf)
- Add support for early relocation when u-boot.bin is loaded to different
address then CONFIG_SYS_TEXT_BASE
- Add rela.dyn and dynsym sections
Disabling NEEDS_MANUAL_RELOC U-Boot size increased by 10% of it's original
size (550kB to 608kB).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a845670b34925859b2e321875f7588a29f6655f9.1655299267.git.michal.simek@amd.com
Symbol handling depends on compilation flags. Right now manual relocation
is used that's why symbols can be referenced just by name and there is no
need to find them out. But when position independent code (PIC) is used
symbols need to be described differently. That's why having one macro
change is easier than changing the whole code.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d704e9a267c8b536452fb999111dbfbc9d652be5.1655299267.git.michal.simek@amd.com
Right now U-Boot runs all the time from the same address where it is loaded
but going to full relocation code starting address doesn't need to be fixed
and can be simply discovered from reading PC register. That's why use r20
to get PC address and subtract offset from the beginning to get starting
address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/044b727c33dfbe662f68512d0da0775a4805f360.1655299267.git.michal.simek@amd.com
Enable u-boot.elf recreation from u-boot.bin to prepare for removing manul
relocation. Enable option for big endian configuration but it is not used
too much that's why it is completely untested.
By supporting this system there is a need to define LITTLE/BIG endian
Kconfig options to pass -EL/-EB flags.
Full command line for u-boot.elf recreation looks like this:
microblazeel-xilinx-linux-gnu-objcopy -I binary -B microblaze \
-O elf32-microblazeel u-boot.bin u-boot-elf.o
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/7e242a519fcd1c693b9103c5599b515af555ca43.1655299267.git.michal.simek@amd.com
CONFIG_SYS_INIT_SP_OFFSET macro place stack to TEXT_BASE - SYS_MALLOC_F_LEN
but there is no reason to do it now because board_init_f_alloc_reserve()
returns exact location where stack should be. That's why stack location is
calculated at run time and there is no need to hardcode it via macro. This
change will help with placing U-Boot to any address.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e9aee69646e022fd8a96cbee2d2a07ab81fb6e05.1655299267.git.michal.simek@amd.com
When U-Boot starts stack protection can be already enabled that's why setup
the lowest possible SLR value which is address 0. And the highest possible
stack in front of U-Boot. That's why you should never load U-Boot to the
beginning of DDR. There must be some space reserved. Code is using this
location for early malloc space, early global data and stack.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/86b9748bad12142659804d6381bc6bbf20be44f1.1655299267.git.michal.simek@amd.com
Board is using kv260 design for couple of parts defined by spec like i2c
eeproms, ina260, uart, etc.
Board has 4 gems. One gem connected via PS SGMII(GT), another PS RGMII(MIO)
and 2 via EMIO. First two shares the same MIO lines for PHYs. PL based one
have separate EMIO lines via PL.
Also two USB 3.0 with usb hubs are present. USB phys and USB hubs should
have separate reset line. The first usb0 hub also has USB-SD controller
(usb2244) connected to port 0.
To test compatibility with k26 you can run:
fdtoverlay -o /tmp/output.dtb -i arch/arm/dts/zynqmp-sm-k26-revA.dtb \
arch/arm/dts/zynqmp-sck-kr-g-revA.dtbo
Also add support for kr260-revB board. Based on FRU it is revision B
but schematics can be label as revA03.
Changes in revB are:
- SFP light
- GEM2/3 TX_CLK fixes
- PMOD/RPI connector fixes
- Replace si5332 with oscilators
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/dac2ee1826e73b89c8cc1e430354eb43d291f675.1652870941.git.michal.simek@amd.com
Add a fuzzing engine driver for the sandbox to take inputs from
libfuzzer and expose them to the fuzz tests.
Signed-off-by: Andrew Scull <ascull@google.com>
Add an implementation of LLVMFuzzerTestOneInput() that starts the
sandbox on a secondary thread and exposes a function to synchronize the
generation of fuzzing inputs with their consumption by the sandbox.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move the program's entry point to os.c, in preparation for a separate
fuzzing entry point to be added.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_ASAN to build with the Address Sanitizer. This only works
with the sandbox so the config is likewise dependent. The resulting
executable will have ASAN instrumentation, including the leak detector
that can be disabled with the ASAN_OPTIONS environment variable:
ASAN_OPTIONS=detect_leaks=0 ./u-boot
Since u-boot uses its own dlmalloc, dynamic allocations aren't
automatically instrumented, but stack variables and globals are.
Instrumentation could be added to dlmalloc to poison and unpoison memory
as it is allocated and deallocated, and to introduce redzones between
allocations. Alternatively, the sandbox may be able to play games with
the system allocator and somehow still keep the required memory
abstraction. No effort to address dynamic allocation is made by this
patch.
The config is not yet enabled for any targets by default.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the sections used to implement linker lists so they begin with
'__u_boot_list' rather than '.u_boot_list'. The double underscore at the
start is still distinct from the single underscore used by the symbol
names.
Having a '.' in the section names conflicts with clang's ASAN
instrumentation which tries to add redzones between the linker list
elements, causing expected accesses to fail. However, clang doesn't try
to add redzones to user sections, which are names with all alphanumeric
and underscore characters.
Signed-off-by: Andrew Scull <ascull@google.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the sections used for defining sandbox command line options so
that they don't start with a '.'. ELF says that sections starting with a
'.' are reserved for system use, but the sandbox runs as a normal user
process so should be using user sections instead.
Clang's ASAN adds redzones to non-user sections and the extra padding
meant that the list of options was being corrupted. Naming the sections
as user sections avoids this issue as clang handles them as we intended.
Signed-off-by: Andrew Scull <ascull@google.com>
Rename the sections used for placing the EFI runtime so that they don't
start with a '.'. ELF says that sections starting with a '.' are
reserved for system use, but the sandbox runs as a normal user process
so should be using user sections instead.
Clang's ASAN adds redzones to non-user sections and the extra padding
meant that the list of options was being corrupted. Naming the sections
as user sections avoids this issue as clang handles them as we intended.
Signed-off-by: Andrew Scull <ascull@google.com>
