The patch adds basic board support for TI's OMAP-L138 based
Hawkboard. This board is pretty similar to the da850 EVM. Support for
nand and network access is added in this version.
The following bootup procedure is used.
At reset, the Rom Boot Loader(RBL), initialises the ddr and the nand
controllers and copies the second stage bootloader(nand_spl) to
RAM. The secondary bootloader then copies u-boot from a predefined
location in the nand flash to the RAM, and passes control to the
u-boot image.
Three config options are supported
* hawkboard_config - Used to create the u-boot.bin. Tftp the
u-boot.bin image to the RAM from u-boot, and flash to the nand flash
at address 0xe0000.
* hawkboard_nand_config - Used to generate the secondary
bootloader(nand_spl) image. This creates an elf file u-boot-spl
under nand_spl/. Create an AIS signed image using this file, and
flash it to the nand flash at address 0x20000. The ais file should
fit in one block.
* hawkboard_uart_config - This is same as the first image, but with
the TEXT_BASE as expected by the RBL(0xc1080000). Create the AIS
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Storage of the board specific values (ethaddr...)
-------------------------------------------------
The board specific environment variables that should be unique
for each individual board, can be stored in the I2C EEPROM. This
will be done from offset 0x80 with the length of 0x80 bytes. The
following command can be used to store the values here:
=> setdef de:20:6a:ed:e2:72 de:20:6a:ed:e2:73 AB0001
ethaddr eth1addr serial#
Now those 3 values are stored into the I2C EEPROM. A CRC is added
to make sure that the values get not corrupted.
SW-Reset Pushbutton handling:
-----------------------------
The SW-reset push button is connected to a GPIO input too. This
way U-Boot can "see" how long the SW-reset was pressed, and a
specific action can be taken. Two different actions are supported:
a) Release after more than 5 seconds and less then 10 seconds:
-> Run POST
Please note, that the POST test will take a while (approx. 1 min
on the 128MByte board). This is mainly due to the system memory
test.
b) Release after more than 10 seconds:
-> Restore factory default settings
The factory default values are restored. The default environment
variables are restored (ipaddr, serverip...) and the board
specific values (ethaddr, eth1addr and serial#) are restored
to the environment from the I2C EEPROM. Also a bootline parameter
is added to the Linux bootline to signal the Linux kernel upon
the next startup, that the factory defaults should be restored.
The command to check this sw-reset status and act accordingly is
=> chkreset
This command is added to the default "bootcmd", so that it is called
automatically upon startup.
Also, the 2 LED's are used to indicate the current status of this
command (time passed since pushing the button). When the POST test
will be run, the green LED will be switched off, and when the
factory restore will be initiated, the reg LED will be switched off.
Loggin of POST results:
-----------------------
The results of the POST tests are logged in a logbuffer located at the end
of the onboard memory. It can be accessed with the U-Boot command "log":
=> log show
<4>POST memory PASSED
<4>POST cache PASSED
<4>POST cpu PASSED
<4>POST uart PASSED
<4>POST ethernet PASSED
The DENX Linux kernel tree has support for this log buffer included. Exactly
this buffer is used for logging of all kernel messages too. By enabling the
compile time option "CONFIG_LOGBUFFER" this support is enabled. This way you
can access the U-Boot log messages from Linux too.
2007-08-10, Stefan Roese <sr@denx.de>
48571ff005