Features supported :
* Serial console
* SPI Flash
* MMC/SD Card
* eMMC storage
* SATA
* PCA9555 - GPIO expander over I2C5 bus
* USB
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
[uri.mashiach@compulab.co.il: Adjust to v2016.11]
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Sometimes devicetree nodes and or properties are added out of the u-boot
console, maybe through some script or manual interaction.
The devicetree as loaded or embedded is quite small, so the devicetree
has to be resized to take up those new nodes/properties.
In original the devicetree was only extended by effective
4 * add_mem_rsv.
With this commit we can add an argument to the "fdt resize" command,
which takes the extrasize to be added.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Simon Glass <sjg@chromium.org>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently MX6 SPL DDR initialization hardcodes the REF_SEL and
REFR fields of the MDREF register as 1 and 7, respectively for
DDR3 and 0 and 3 for LPDDR2.
Looking at the MDREF initialization done via DCD we see that
boards do need to initialize these fields differently:
$ git grep 0x021b0020 board/
board/bachmann/ot1200/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/ccv/xpress/imximage.cfg:DATA 4 0x021b0020 0x00000800 /* MMDC0_MDREF */
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x7800
board/freescale/mx6qarm2/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qarm2/imximage_mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6dl.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6qsabreauto/mx6qp.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6dlsabresd.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6sabresd/mx6q_4x_mt41j128.cfg:DATA 4 0x021b0020 0x00005800
board/freescale/mx6slevk/imximage.cfg:DATA 4 0x021b0020 0x00001800
board/freescale/mx6sxsabreauto/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/freescale/mx6sxsabresd/imximage.cfg:DATA 4 0x021b0020 0x00000800
board/warp/imximage.cfg:DATA 4 0x021b0020 0x00001800
So introduce a mechanism for users to be able to configure
REFSEL and REFR fields as needed.
Keep all the mx6 SPL users in their current REF_SEL and REFR values,
so no functional changes for the existing users.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
ft_board_setup may return early in the case that the board revision
cannot be obtained. In that case it is assumed that no revision
specific correction in the fdt is neccessary. But the mtd partitions
will not be fixed up either altough they are not revision specific.
Move the call to fdt_fixup_mtdparts in front of the revision specific
part to ensure that the partitions are fixed up even if the board
revision cannot be obtained.
While on it, fix a spelling mistake in a comment introduced by the
same commit.
Fixes: 62d6bac660 ("ARM: board: cm_fx6: fixup mtd partitions in the fdt")
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Nikita Kiryanov <nikita@compulab.co.il>
The cm-fx6 module has an on-board st,m25p compatible spi flash chip
used for U-Boot (binary & environment). Overwrite the partitions in
the device tree by the partition table provided in the mtdparts
environment variable, if it is set.
This allows to specify a kernel independent partitioning in the
environment and provides a convient way for the user to adapt the
partition table.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Old revisions of Utilite (based on cm-fx6) do not have a dedicated
card detect pin. But the card is removable by the user and card
detection can be realized with polling (e.g. supported by Linux).
Add the broken-cd property to the mmc device tree instead of the
non-removable property to make card detection possible if polling
is supported.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Add layout definitions and implement functions for field printing/updating,
layout detection, layout assignment, and layout parsing.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
There is no distinction between essential and non-essential mux configuration,
so it doesn't make sense to have an "essential" prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
During boot, U-Boot raises the CPU frequency but the CORE and MPU regulators
are not updated. This is not a problem in cold boot since the default values
that the pmic outputs are correct, but if Linux were to switch the module to a
low power OPP, the new voltage values will be retained after a reboot and the
module will likely hang once U-Boot raises the CPU frequency back up.
Set both CORE and MPU regulators to to 1.1V on boot.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
CM-T43 does not have a vtt regulator. Remove the function that's supposed
to enable it.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Set TPS65218 FSEAL bit to 1 so that RTC could be powered using on-board
3V battery. This is necessary so that time and date will survive reboots and
power offs.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Simplify the board file by splitting it to spl portion and u-boot portion.
Some unnecessary includes were identified and removed. No functional changes.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adjust all Tegra boards to use driver model for Ethernet, now that the
required drivers are converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
CM-T3517 has several HW revisions.
Add board specific get_board_rev() callback to retrieve revision number.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Igor Grinberg <grinberg@compulab.co.il>
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add the following splash locations to cm-fx6:
* filesystem formatted mmc
* filesystem formatted usb
* filesystem formatted sata
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for loading splash image from an SD card formatted with
a filesystem. Update boards to maintain original behavior where needed.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This introduces omap_die_id_display to display the full die id.
There is no need to store it in an environment variable, that no boot script
is using anyway.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
Old revisions of Utilite (a miniature PC based on cm-fx6) do not have
a card detect for mmc, and thus the kernel needs to be told that
there's a persistent storage on usdhc3 to force it to probe the mmc
card.
Check the baseboard revision and modify the device tree accordingly
if needed.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Introduce cl_eeprom_get_product_name() for obtaining product name
from the eeprom.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
cl_eeprom_read_mac_addr() doesn't differentiate between success case and
inability to access eeprom. Fix this by propagating the return value of
cl_eeprom_setup().
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for selecting which eeprom is queried for board revision by
extending cl_eeprom_get_board_rev() to accept an i2c bus number.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
On some CM-FX6 modules U-Boot attempts to configure the usb0 controller in
device mode, which renders it unavailable:
USB0: Port not available.
and also causes usb stop to report an error
EHCI failed to shut down host controller.
This happens mostly on MX6 Dual based modules, and is caused by the USBPHY_CTRL
register reporting USBPHY_CTRL_OTG_ID to be 1, even when it is pulled down.
Since we do not support device mode in cm-fx6 u-boot, force all controllers to
be configured as hosts.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add initial support for CM-T43, an AM437x based SoM.
This support includes: serial, MMC/eMMC, NAND, USB, ETH, I2C, GPIO, DRAM
detection.
Cc: Tom Rini <trini@konsulko.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Refactor display code to only setup hdmi if do_enable_hdmi() is invoked.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for selecting display preset using the environment variable
"displaytype". This is a preparation for future merging of compulab
omap3_display.c display selection code with the cm-fx6 display selection code.
The "panel" environment variable is retained for backwards compatibility.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement a cm-fx6 specific board_video_skip() to provide the option to not
initialize the display.
The new function does not init display if the environment variable "panel" is
not defined, or if it is set to an unsupported value.
Collateral changes:
- Don't use the global displays array (it's CONFIG_IMX_VIDEO_SKIP specific).
- Don't use detect_hdmi(), since env controlled init makes it unnecessary.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
U-Boot does not explicitly assign the display to an IPU interface. Instead, it
relies on the power-on default of DI0.
Since the kernel reassigns HDMI display to DI1, after a warm reset the HDMI
display no longer works in U-Boot.
Fix this by explicitly assigning HDMI to IPU1 DI0 in U-Boot.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This introduces OMAP3 support for the common omap boot code, as well as a
major cleanup of the common omap boot code.
First, the omap_boot_parameters structure becomes platform-specific, since its
definition differs a bit across omap platforms. The offsets are removed as well
since it is U-Boot's coding style to use structures for mapping such kind of
data (in the sense that it is similar to registers). It is correct to assume
that romcode structure encoding is the same as U-Boot, given the description
of these structures in the TRMs.
The original address provided by the bootrom is passed to the U-Boot binary
instead of a duplicate of the structure stored in global data. This allows to
have only the relevant (boot device and mode) information stored in global data.
It is also expected that the address where the bootrom stores that information
is not overridden by the U-Boot SPL or U-Boot.
The save_omap_boot_params is expected to handle all special cases where the data
provided by the bootrom cannot be used as-is, so that spl_boot_device and
spl_boot_mode only return the data from global data.
All of this is only relevant when the U-Boot SPL is used. In cases it is not,
save_boot_params should fallback to its weak (or board-specific) definition.
save_omap_boot_params should not be called in that context either.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
enable_spi_clock does the same thing with enable_cspi_clock, so
remove enable_cspi_clock.
Remove enable_cspi_clock prototype in header file
convert cm_fx6/spl.c to use enable_spi_clk
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
All the Tegra boards borrow the files from board/nvidia/common/
directory, i.e., board/nvidia/common/* are not vendor-common files,
but SoC-common files.
Move NVIDIA common files to arch/arm/mach-tegra/ to clean up
Makefiles.
As arch/arm/mach-tegra/board.c already exists, this commit renames
board/nvidia/common/board.c to arch/arm/mach-tegra/board2.c,
expecting they will be consolidated as a second step.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now CONFIG_SPL_BUILD is not defined in Kconfig, so
"!depends on SPL_BUILD" and "if !SPL_BUILD" are redundant.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Move board/compulab/common/splash.c code to
common/splash_source.c to make it available for everybody. This move
renames cl_splash_screen_prepare() to splash_source_load(), and
the compilation of this code is conditional on CONFIG_SPLASH_SOURCE.
splash_source features:
* Provide a standardized way for declaring board specific splash screen
locations
* Provide existing routines for auto loading the splash image from the
locations as declared by the board
* Introduce the "splashsource" environment variable, which makes it
possible to select the splash image source.
cm-t35 and cm-fx6 are updated to use the modified version.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add support for splash screen.
The splash screen is loaded from the SPI flash and is displayed on the
HDMI display.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: minor code and commit message updates]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Add support for loading splash from sf.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
[grinberg@compulab.co.il: staticize the sf global variable]
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Define a generic way for boards to define splash image locations:
- introduce struct splash_location
- introduce enum splash_storage
- update cl_splash_screen_prepare() to take an array of above struct
and select the appropriate one based on the splashsource environment
variable (if it is not defined- use the first splash location as default).
cm-t35 is updated to work with the new interface.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Move storage device specific code into its own function instead of
calling it directly from an otherwise storage device independent
function (cl_splash_screen_prepare).
This is a preparation for supporting multiple splash locations.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Obtain 2nd NIC MAC address from baseboard EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement the option to select the eeprom i2c bus when reading mac
address.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When passing eth address to Linux via dtb, the "local-mac-address"
property should be set for "/soc/aips-bus@02100000/ethernet@02188000",
not "/fec".
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
Provide board specific implementation for sata stop command for
cm_fx6.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
This function can fail if the device tree runs out of space. Rather than
silently booting with an incomplete device tree, allow the failure to be
detected.
Unfortunately this involves changing a lot of places in the code. I have
not changed behvaiour to return an error where one is not currently
returned, to avoid unexpected breakage.
Eventually it would be nice to allow boards to register functions to be
called to update the device tree. This would avoid all the many functions
to do this. However it's not clear yet if this should be done using driver
model or with a linker list. This work is left for later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Many boards use a minimal .cfg file in the SPL case.
Introduce spl_sd.cfg so that we can reuse it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Add both host and mUSB support.
Currently, the selection between host USB and mUSB is done through the
config file.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
CompuLab cm-t3517 is Computer on Module (CoM) based on AM3517 SoC.
Features: up to 256MB DDR2, up to 512MB NAND, USB hub, mUSB, WiFi, BT,
Analog audio codec, touch screen controller, LED.
Add basic support including:
LED, Serial console, NAND, MMC, GPIO, I2C, 256MB DRAM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Switch the default CD GPIO polarity to active low.
The current hsmmc driver assumption that the CD GPIO is active high, but
in the real hardware, usually the opposite holds.
The usual SD card socket has a mechanical switch which is grounded as
soon as a card is inserted.
Of course there might be some board logic which inverts the signal, but
as far as current users are concerned, there is no such logic.
Current U-Boot users either not using the CD functionality, or have a
different way (e.g. external to SoC GPIO controller) for checking the
card presence.
This patch also brings the polarity assumption in line with the Linux
kernel and adds appropriate comments.
This patch also might spare issues once the TWL GPIO driver will be
converted to the DM.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The fallback is used for cases when CONFIG_SERIAL_TAG defined, but the
eeprom is not used.
The fallback is useful for more than one CompuLab board, so move it to a
common location.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract the SMC911x initialization code to a common location where it
can be reused by other compulab omap3 based boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The splash screen loading code can be reused by other compulab boards.
For now extract it to a common location for further reuse.
This also switches the splash code dependency from CONFIG_LCD to
CONFIG_SPLASH_SCREEN as it should normally be.
In addition this patch fixes the accidental dependency of the
get_board_mem_timings() function on CONFIG_LCD, by just moving the
splash code and leaving the above function intact.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Extract the USB hub reset code to a common location where it can be
reused by other compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Move board revision handling code to a common location
for further reuse.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
The 1GB DRAM configuration on mx6 solo uses 2 chip selects, but
the code tests 1GB DRAM configuration as if it is all present on one
chip select, and thus cannot see the full range of available memory.
Refactor the check to detect 1GB DRAM correctly.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Change the order in which GPIOs are toggled in SATA init sequence to
accomodate both SanDisk and Phison SSDs.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The platform_data definitions are generally referenced from both
drivers and board files. That is why header files defining
platform_data sturectures are placed in "include" directory,
but our top level "include" directory is already too cluttered.
Let's collect platform_data definitions under the directory
"include/dm/platform_data" like Linux gathers ones around under
"include/linux/platform_data".
This commit moves two header files:
include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h
include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The gpmc_init() function already calls enable_gpmc_cs_config() for chip
select 0. Although the bus width is configured for 16 bit, it gets
reconfigured correctly in the omap_gpmc driver later.
Remove the enable_gpmc_cs_config() function call and the associated
gpmc_nand_config[] array.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Now that serial and GPIO are available for iMX.6, move cm_fx6 over as an
example.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Use gpio_request for all the gpios that are utilized by various
subsystems in cm-fx6, and refactor the relevant init functions
so that all gpios are requested during board_init(), not during
subsystem init, thus avoiding the need to manage gpio ownership
each time a subsystem is initialized.
The new division of labor is:
During board_init() muxes are setup and gpios are requested.
During subsystem init gpios are toggled.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Add default eeprom bus setting.
This addresses the trimslice compile error that was introduced
with the addition of this setting.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.
We can delete the ones in arch and board Kconfig files.
This commit can be easily reproduced by the following command:
find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
N
s/\n[[:space:]]*string//
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add support for SATA.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Use Compulab eeprom module to obtain revision number, serial number, and
mac address from the EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add support for all 3 I2C busses on Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add USB and USB OTG host support for Compulab CM-FX6 CoM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add ethernet support for Compulab CM-FX6 CoM
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add initial support for Compulab CM-FX6 CoM.
Support includes MMC, SPI flash, and SPL with dynamic DRAM detection.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Create CONFIG_SYS_I2C_EEPROM_BUS #define to tell the EEPROM
module what I2C bus the EEPROM is located at. Make cl_eeprom_read()
switch to that bus when reading EEPROM.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP5 board select menu to omap5/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap5").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the OMAP3 board select menu to omap3/Kconfig.
Move also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="omap3
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Tegra board select menu to tegra/Kconfig.
Insert the Tegra SoC select menu between the arch select and the
board select.
Architecture select
|-- Tegra Platform (Tegra)
|- Tegra SoC select (Tegra20 / 30 / 114 / 124)
|- Board select
Consolidate also common settings (CONFIG_SYS_CPU="armv7" and
CONFIG_SYS_SOC="tegra*") and always "select" CONFIG_SPL as follows:
config TEGRA
bool
select SPL
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Boot from eMMC boot partition corresponds to BOOT_DEVICE_MMC2
omap_bootmode, while BOOT_DEVICE_MMC2_2 corresponds to the user
data partition boot.
Fix mmc_get_env_part() boot mode check to use a correct value.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Fix cl_eeprom_read_mac_addr() return value check.
Fix long line codding style issue in board_init().
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
We have switched to Kconfig and the boards.cfg file is going to
be removed. We have to retrieve the board status and maintainers
information from it.
The MAINTAINERS format as in Linux Kernel would be nice
because we can crib the scripts/get_maintainer.pl script.
After some discussion, we chose to put a MAINTAINERS file under each
board directory, not the top-level one because we want to collect
relevant information for a board into a single place.
TODO:
Modify get_maintainer.pl to scan multiple MAINTAINERS files.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Suggested-by: Tom Rini <trini@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit adds:
- arch/${ARCH}/Kconfig
provide a menu to select target boards
- board/${VENDOR}/${BOARD}/Kconfig or board/${BOARD}/Kconfig
set CONFIG macros to the appropriate values for each board
- configs/${TARGET_BOARD}_defconfig
default setting of each board
(This commit was automatically generated by a conversion script
based on boards.cfg)
In Linux Kernel, defconfig files are located under
arch/${ARCH}/configs/ directory.
It works in Linux Kernel since ARCH is always given from the
command line for cross compile.
But in U-Boot, ARCH is not given from the command line.
Which means we cannot know ARCH until the board configuration is done.
That is why all the "*_defconfig" files should be gathered into a
single directory ./configs/.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Make the common eeprom library available for any I2C driver.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
cm-t54 Eth MAC address is stored in onboard EEPROM.
Add EEPROM support and setup stored Eth MAC address.
If EEPROM does not contain a valid MAC, then generate it from the
processor ID code (reference code is taken from OMAP5 uEvm board file).
Modify Device Tree blob MAC address field with retrieved data.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This renames all the Tegra20 pinmux pins and functions so they have a
prefix which matches the type name.
The entries in tegra20_pingroups[] are all updated to remove the columns
which are no longer used.
All affected code is updated to match.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Copied from Linux sources "include/linux/sizes.h" commit
413541dd66d51f791a0b169d9b9014e4f56be13c
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stefan Roese <sr@denx.de>
[trini: Add bcm Kona platforms to the patch]
Signed-off-by: Tom Rini <trini@ti.com>
Some platforms like AM437x have different EVMs with different phy addresses,
so this patch adds support for passing phy address via cpsw plaform data.
Also renamed phy_id to phy_addr so better understanding of the code.
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
[trini: Update BuR am335x_igep0033 pcm051_rev3 pcm051_rev1 cm_t335
pengwyn boards]
Signed-off-by: Tom Rini <trini@ti.com>
This prevents references to _end from generating absolute
relocation records.
This change is binary invariant for ARM targets.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Newly added cm_t335 was missed in commit 47ed5dd0 which
made ARM targets produce full ELF files. Fix its linker
script.
This change is binary-invariant when only .dynsym, .dynstr,
.dynamic, .plt, .interp and .gun sections are declared.
Sections .hash, .got.plt, .dynbss and .ARM.exidx are also
declared so that their (unused) content is moved out of the
u-boot binary.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Unlike Linux Kernel, U-Boot historically had *.dts files under
board/$(VENDOR)/dts/ and *.dtsi files under arch/$(ARCH)/dts/.
I think arch/$(ARCH)/dts dicretory is a better location
to store both *.dts and *.dtsi files.
For example, before this commit, board/xilinx/dts directory
had both Microblaze dts (microblaze-generic.dts) and
ARM dts (zynq-*.dts), which are totally unrelated.
This commit moves *.dts to arch/$(ARCH)/dts/ directories,
allowing us to describe nicely mutiple DTBs generation in the next commit.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit changes the working directory
where the build process occurs.
Before this commit, build process occurred under the source
tree for both in-tree and out-of-tree build.
That's why we needed to add $(obj) prefix to all generated
files in makefiles like follows:
$(obj)u-boot.bin: $(obj)u-boot
Here, $(obj) is empty for in-tree build, whereas it points
to the output directory for out-of-tree build.
And our old build system changes the current working directory
with "make -C <sub-dir>" syntax when descending into the
sub-directories.
On the other hand, Kbuild uses a different idea
to handle out-of-tree build and directory descending.
The build process of Kbuild always occurs under the output tree.
When "O=dir/to/store/output/files" is given, the build system
changes the current working directory to that directory and
restarts the make.
Kbuild uses "make -f $(srctree)/scripts/Makefile.build obj=<sub-dir>"
syntax for descending into sub-directories.
(We can write it like "make $(obj)=<sub-dir>" with a shorthand.)
This means the current working directory is always the top
of the output directory.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Gerhard Sittig <gsi@denx.de>
Currently same value is programmed for all ioregs. This is not
the case for all SoC's like AM4372. So adding a structure for ioregs
and updating in all board files. And also return from config_cmd_ctrl()
and config_ddr_data() functions if data is not passed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Fixup dxr2, cm_t335, adapt pcm051 rev3]
Signed-off-by: Tom Rini <trini@ti.com>
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Based on the definitive guide to EMIF configuration[1] certain registers
that we have been modifying (and are documented registers) should be
left in their reset values rather than modified. This has been tested
on AM335x GP EVM and Beaglebone White.
[1]: http://processors.wiki.ti.com/index.php/AM335x_EMIF_Configuration_tips
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Javier Martinez Canillas <javier@dowhile0.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Add support for status LED. Use the STATUS_LED APIs for indicating a
boot progress.
Signed-off-by: Ilya Ledvich <ilya@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
- add omap24xx driver to new multibus/multiadpater support
- adapted all config files, which uses this driver
Tested on the am335x based siemens boards rut, dxr2 and pxm2
posted here:
http://patchwork.ozlabs.org/patch/263211/
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Tom Rini <trini@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Steve Sakoman <sakoman@gmail.com>
Cc: Thomas Weber <weber@corscience.de>
Cc: Tom Rix <Tom.Rix@windriver.com>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Yanok <yanok@emcraft.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Peter Barada <peter.barada@logicpd.com>
Cc: Nagendra T S <nagendra@mistralsolutions.com>
Cc: Michael Jones <michael.jones@matrix-vision.de>
Cc: Raphael Assenat <raph@8d.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefano Babic <sbabic@denx.de>
Use scf0403 driver to add scf0403x LCD support for cm-t35 and cm-t3730
boards.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Switch to using the generic gpio_led driver instead of the private to
cm_t35 board led implementation.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h
Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:
board/compulab/common/Makefile
board/udoo/Makefile
include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.
include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.
Note: 'git show' will also list two files just because
they are new:
include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h
Current predefines do not fit cm-t3730 very well (some of them produce
artifacts in the image).
Update LCD predefines to accommodate both cm-t35 and cm-t3730 modules.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Compulab OMAP3 boards use the same display initialization code.
Move the display initialization code to live under board/compulab/common
directory.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Compulab boards use the same eeprom code, so move the eeprom related
code to live under board/compulab/common directory.
Also make several adjustments to eeprom functions namespace, so it will
be generic for compulab boards.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
We have converted all makefiles needed to build $(LIBS).
Until this commit we used to grep switch so that U-Boot style
and Kbuild style makefiles coexist.
But we do not need any more.
Goint forward, use always Kbuild style Makefile when adding
a new Makefile
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Currently the cm-t35 support code lives under board/cm_t35 directory.
Some of the code can be shared with other/future CompuLab boards,
so move the cm-t35 to live under board/compulab/cm_t35 directory.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Linux dts files were used for those boards that didn't already
have sdhci info populated. Tamonten has their own dtsi file with
common sdhci nodes (sourced from Linux).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
dts Makefile has the arch & board include paths added to DTS_CPPFLAGS.
This allows the use of '#include "xyz"' in the dts/dtsi file which
helps the C preprocessor find common dtsi include files.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
TrimSlice's USB1 port has two purposes; it either acts as a device port
hosting Tegra's USB recovery protocol, or acts as a host port connected
to the internal USB->SATA bridge chip, which may in turn be connected to
an SSD or HDD. Add the appropriate device tree and board configuration
options to enable this port as a host port, and route the port to the
SATA bridge using the VBUS GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Non-Nvidia boards to include newly added features (like emc clock
scaling) it would be necessary to add each feature to their own board
Makefile. This is because currently the top Makefile automaticly includes
these features only for Nvidia boards.
This patch adds a simple Makefile include so all new features become
available for non-Nvidia board vendors.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
