Let the mpll dividers achieve the closest rate possible, even if
it means rounding the requested rate up.
This is done to improve the accuracy of the rates provided by these
plls to the audio subsystem
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Allow the mpll driver to round the requested rate up if
CLK_MESON_MPLL_ROUND_CLOSEST is set and it provides a rate closer to the
requested rate.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl<martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Until commit 05f814402d ("clk: meson: add fdiv clock gates") we
relied on the bootloader to enable the fclk_div clock gates. It turns
out that our clock tree is incomplete at least on Meson8b (tested with
an Odroid-C1, which uses an RGMII PHY) because after the mentioned
commit Ethernet is not working anymore (no RX/TX activity can be seen).
At the same time Ethernet was still working on Meson8m2 with a RMII PHY.
Testing has shown that as soon as "fclk_div2" is disabled Ethernet stops
working on Odroid-C1. Unfortunately it's currently not clear what the
Ethernet controller IP block uses the fclk_div2 clock for. Mark the
clock as CLK_IS_CRITICAL to keep it enabled (as it's already enabled by
most bootloaders by default, which is why we didn't notice it before).
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Replace every license notices in drivers/clk/meson by SPDX license
identifiers, as described in license-rules.rst
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clk81 is not expected to be changed, so drop this flag.
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Adds a Clock and Reset controller driver for the Always-On part
of the Amlogic Meson-AXG SoC.
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
We try to refactor the common code into one dedicated file,
while preparing to add new Meson-AXG aoclk driver, this would
help us to better share the code by all aoclk drivers.
Suggested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
There is a protential memory leak, as of_clk_del_provider is
never called if of_clk_add_hw_provider has been executed.
Fix this by using devm variant API.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Suggested-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the SEL/DIV/GATE for VDEC_1 and VDEC_HEVC.
Signed-off-by: Maxime Jourdan <maxi.jourdan@wanadoo.fr>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the NAND clocks (from the HHI_NAND_CLK_CNTL register) to the
Meson8b clock driver. There are three NAND clocks: a gate which enables
or disables the NAND clock, a mux and a divider (which divides the mux
output).
Unfortunately the public S805 datasheet does not document the mux
parents. However, the vendor kernel has a few hints for us which allows
us to make an educated guess about the clock parents. To do this we need
to have a look at set_nand_core_clk() from the vendor's NAND driver (see
[0]):
- XTAL = (4<<9) | (1<<8) | 0
- 160MHz = (0<<9) | (1<<8) | 3)
- 182MHz = (3<<9) | (1<<8) | 1)
- 212MHz = (1<<9) | (1<<8) | 3)
- 255MHz = (2<<9) | (1<<8) | 1)
While there is a comment for the XTAL parent (which indicates that it
should only be used for debugging) we have to do a bit of math for the
other parents: target_freq * divider = rate of parent clock
Bit 8 above is the enable bit, so we can ignore it here. Bits 11:9 are
the mux index and bits 6:0 are the 0-based divider (so we need to add
1). This gives us:
- mux 0 (160MHz * 4) = fclk_div4 (actual rate = 637.5MHz, off by 2.5MHz)
- mux 1 (212MHz * 4) = fclk_div3 (actual rate = 850MHz, off by 2MHz)
- mux 2 (255MHz * 2) = fclk_div5 (matches exactly 510MHz)
- mux 3 (182MHz * 2) = fclk_div7 (actual rate = 346.3MHz, off by 0.3MHz)
[0] https://github.com/khadas/linux/blob/9587681285cb/drivers/amlogic/amlnf/dev/amlnf_ctrl.c#L314
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
meson8b_cpu_clk has two parent clocks:
- meson8b_xtal
- meson8b_cpu_scale_out_sel
The name of the "xtal" clock parent is specified correctly. However,
there is a typo in the name of the second parent clock. The
meson8b_cpu_scale_out_sel definition uses the name "cpu_scale_out_sel"
(which matches the name from the datasheet). However, the mux parent
definition uses the name "cpu_out_sel" which does not match any existing
clock.
Fixes: 251b6fd38b ("clk: meson: rework meson8b cpu clock")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The names of all fclk divider gate clocks follow the naming schema
"fclk_divN" and the name of all fclk fixed dividers follow the naming
schema "fclk_divN_div".
There's one exception to this rule: meson8b_fclk_div3_div's name is
"fclk_div_div3". It's child clock meson8b_fclk_div3 however references
it as "fclk_div3_div" (following the naming schema explained above).
Fix the naming of the meson8b_fclk_div3_div clock to follow the naming
schema. This also fixes serial console on my Meson8m2 board because
"clk81" uses fclk_div3 as parent. However, since the hierarchy stops at
meson8b_fclk_div3 there's no known parent clock and the rate of "clk81"
and all of it's children (UART clock, SDIO MMC controller clock, ...)
are all 0.
Fixes: 05f814402d ("clk: meson: add fdiv clock gates")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Using __clk_mux_determine_rate effectively ignores CLK_MUX_ROUND_CLOSEST
if set the related clk_regmap mux instance.
Use clk_mux_determine_rate_flags() to make sure the flag is honored.
Fixes: ea11dda9e0 ("clk: meson: add regmap clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Fixes the following warnings:
drivers/clk/meson/meson8b.c:512:19: warning: symbol 'meson8b_mpeg_clk_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:526:19: warning: symbol 'meson8b_clk81' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:540:19: warning: symbol 'meson8b_cpu_in_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:591:19: warning: symbol 'meson8b_cpu_scale_div' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:608:19: warning: symbol 'meson8b_cpu_scale_out_sel' was not declared. Should it be static?
drivers/clk/meson/meson8b.c:626:19: warning: symbol 'meson8b_cpu_clk' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:392:27: warning: symbol 'gxbb_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/gxbb.c:439:27: warning: symbol 'gxl_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:195:27: warning: symbol 'axg_gp0_init_regs' was not declared. Should it be static?
drivers/clk/meson/axg.c:248:27: warning: symbol 'axg_hifi_init_regs' was not declared. Should it be static?
drivers/clk/meson/meson8b.c: In function 'meson8b_clkc_probe':
drivers/clk/meson/meson8b.c:1052:14: warning: unused variable 'clk' [-Wunused-variable]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
clk81 is a composite clock which parents all the peripheral clocks of the
platform. It is a critical clock which is used as provided by the
bootloader. We don't want to change its rate or reparent it, ever.
Remove the CLK_IGNORE_UNUSED on the mux and divider. These clock can't
gate so the flag is useless, and the gate is already critical, so the
clock won't ever be unused.
Remove CLK_SET_RATE_NO_REPARENT from mux, it is useless since the mux is
read-only.
Remove CLK_SET_RATE_PARENT from the gate and divider and use ro_ops for
the divider. A peripheral clock should not try to change the rate of
clk81. Stopping the rate propagation is good way to make sure such request
would be ignored.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Fdiv fixed dividers clocks of the fixed_pll can actually gate
independently. We never had an issue so far because these clocks
were provided 'enabled' by the bootloader.
Add these gates to enable/disable the clocks when required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll clocks parent can actually be divided by 1 or 2. So far, this
divider has always been set to 1, so the calculation was correct.
Now that we know it exists, model the tree correctly. If we ever get
a platform where the divider is different, we won't get into trouble
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the hifi pll to the axg clock controller. This clock maybe used as an
input of the axg audio clock controller. It uses the same settings table
as the gp0 pll but has a frac parameter allowing more precision.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Provide an option for the pll driver to round to the rate closest to the
requested rate, instead of systematically rounding down.
This may allow the provided rate to be closer to the requested rate when
rounding up is not an issue
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the frac parameter for the gp0 pll of the axg and gxl.
This allows to achieve rates between the fixed settings provided
by the table.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Finding the appropriate settings of meson plls is too tricky to be done
entirely at runtime, using calculation only. Many combination of m, n
and od won't lock which is why we are using a table for this. However,
for plls having a fractional parameters, it is possible to improve on
the result provided by the table by calculating the frac parameter.
This change adds the calculation of frac when the parameter is available
and the rate provided by the table is not an exact match for the
requested rate.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After testing, it appears that the gxl (and axg) does not require the
special locking/reset loop which was initially added for it.
All the values present in the gxl table can locked with the simple lock
checking loop.
The change switches the gxl and axg gp0 back to the simple lock checking
loop and removes the code no longer required.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Poking CNTL first may take the PLL out of reset while we are still
applying the initial settings, including the filter values
initialization. This is the case for the axg and gxl gp0 pll.
Doing this poke last ensures the pll stays in reset while the initial
settings are applied.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the missing frac parameter to the meson8b fixed_pll. It seems to be
always on this platform, so the rate remains unchanged
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On gxbb and axg, try to get the hhi regmap from the parent DT node, which
should be the HHI system controller once the necessary changes have been
made in amlogic's DTs
Until then, if getting regmap through the system controller fails, the
clock controller will fall back to the old way, requesting memory region
directly and then registering the regmap itself.
This should allow a smooth transition to syscon
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b cpu_clk has been replaced by a set of divider and mux clocks.
meson_cpu_clk is no longer used and can be removed
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Instead of migrating meson cpu_clk to clk_regmap, like the other meson
clock drivers, we take advantage of the massive rework to get rid of it
completely, and solve (the first part) of the related FIXME notice.
As pointed out in the code comments, the cpu_clk should be modeled with
dividers and muxes it is made of, instead of one big composite clock.
The cpu_clk was not working correctly to enable dvfs on meson8b. It hangs
quite often when changing the cpu clock rate. This new implementation,
based on simple elements improves the situation but the platform will
still hang from time to time. This is not acceptable so, until we can
make the mechanism around the cpu clock stable, the cpu clock subtree
has been put in read-only mode, preventing any change of the cpu clock
The notifier and read-write operation will be added back when we have a
solution to the problem.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The mpll clock is a kind of fractional divider which can gate.
When the RW operation have been added, enable/disable ops have been
mistakenly inserted in this driver. These ops are essentially a
poor copy/paste of the generic gate ops.
This change removes the gate ops from the mpll driver and inserts a
generic gate clock on each mpll divider, simplifying the mpll
driver and reducing code duplication.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson pll driver to use clk_regmap and move meson8b, gxbb and
axg's clock using meson_clk_pll to clk_regmap.
This rework is not just about clk_regmap, there a serious clean-up of
the driver code:
* Add lock and reset field: Previously inferred from the n field.
* Simplify the reset logic: Code seemed to apply reset differently but
in fact it was always the same -> assert reset, apply params,
de-assert reset. The 2 lock checking loops have been kept for now, as
they seem to be necessary.
* Do the sequence of init register pokes only at .init() instead of in
.set_rate(). Redoing the init on every set_rate() is not necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson audio divider driver to use clk_regmap and move gxbb
clock using meson_clk_audio_divider to clk_regmap.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Rework meson mpll driver to use clk_regmap and move meson8b, gxbb
and axg clocks using meson_clk_mpll to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock drivers are using struct parm to describe each field of the
clock provider. Providing helpers to access these fields with regmap
helps to keep drivers readable
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_mux to clk_regmap
Also remove a few useless tables in the process
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_divider to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move meson8b, gxbb and axg clocks using clk_gate to clk_regmap
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This change registers a regmap in meson8b, gxbb and axg controllers.
The clock are still accessing their registers directly through iomem.
Once all clocks handled by these controllers have been move to regmap,
the regmap register will be removed and replaced with a syscon request.
This is needed because other drivers, such as the HDMI driver, need to
access the HHI register region
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
aoclk_gate_regmap has been replaced by meson's clk_regmap.
It is no longer necessary so, remove it
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Drop the gxbb ao specific regmap based clock and use the
meson clk_regmap based clock instead.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Meson clock controllers need to move the classical iomem registers to
regmap. This is triggered because the HHI controllers found on the GXBB
and GXL host more than just clocks. To properly handle this, we would
like to migrate HHI to syscon. Also GXBB AO clock controller already use
regmap, AXG AO and Audio clock controllers will as well.
The purpose of this change is to provide a common structure to these
meson controllers (and possibly others) for regmap based clocks.
This change provides the basic gate, mux and divider, based on the
helpers provided by the related generic clocks
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Over time things changes in CCF and issues have been fixed in meson
controllers.
Now, clk81 is decently modeled by read-only PLLs, a mux, a divider
and a gate. We can remove the FIXME comments related to clk81.
Also remove the comment about devm_clk_hw_register, as there is
apparently nothing wrong with it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
We don't need several loop index variables in the probe function
This is far from being critical but since we are doing a vast
rework of meson clock controllers, now is the time to lower the
entropy a bit
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
There is no remove callbacks in meson's clock controllers and
of_clk_del_provider is never called if of_clk_add_hw_provider has been
executed, introducing a potential memory leak.
Fixing this by the using the devm variant.
In reality, the leak would never happen since these controllers are
never unloaded once in use ... still, this is worth cleaning.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The 'dev' pointer is directly available in gxbb and axg clock
controller, so consistently use it instead of going the through the
'pdev' pointer once in while
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On axg, the rate of the mpll is stuck as if sdm value was 4 and could not
change (expect for mpll2 strangely). Looking at the vendor kernel, it
turns out a new magic bit from the undocumented HHI_PLL_TOP_MISC register
is required.
Setting this bit solves the problem and the mpll rates are back to normal
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the datasheet, the od shift of sys_pll is actually 16.
Fixes: 78b4af312f ('clk: meson-axg: add clock controller drivers')
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[fixed commit message]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll also has a fractional part. On axg s400 board, without
this parameter, the calculated rate is off by ~8Mhz (0,4%). The fixed_pll
being the root of the peripheral clock tree, this error is propagated to
the rest of the clocks
Adding the definition of the parameter fixes the problem
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The fixed_pll of gxbb and gxl also has a fractional parameter. This has
not been a problem so far because the fractional part is actually set
to 0 on these platforms, so the rate remains correct when it is ignored.
Still, it is better represent the pll the way it is, so add the frac
parameter now
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The rate of the parent should not be multiplied by 2 when the pll has a
fractional part. This is making the rate calculation of the gxl_hdmi_pll
wrong (and others as well). This multiplication is specific
to the hdmi_pll of gxbb and is most likely due to a multiplier sitting
in front of this particular pll.
Add a fixed factor clock in front on the gxbb pll and remove this constant
from the calculation to fix the problem
Fixes: 4a47295144 ("clk: meson: fractional pll support")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The hdmi pll used in the gxl family is actually different from the gxbb
one. The register layout is completely different, which explain why the
hdmi pll rate has always been rubbish on the gxl family.
Adding the correct register field is the first part of the fix to get a
correct rate out the hdmi pll
Fixes: 0d48fc558d ("clk: meson-gxbb: Add GXL/GXM GP0 Variant")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Some meson plls, such as the hdmi pll, are using a 3rd od parameter,
which is yet another "power of 2" post divider. Add it to fix the
calculation of the hdmi_pll rate
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Use the fractional part width in the calculation instead of 12, which
happens to be the witdh right now. This is safer in case the field width
ever change in the future
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The pll driver performs the rate calculation in Mhz, which adds an
unnecessary rounding down to the Mhz of the rate. Use 64bits long
integers to perform this calculation safely on meson8b and perform the
calculation in Hz instead
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Read-only plls don't need param table to recalculate the rate.
Providing them with a param table is just a waste of memory.
Remove the useless tables from sys_pll on gxbb and axg.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Make sure the rate param table is available before using it.
Some read-only plls don't provide it, which is ok since the
table is not used by read-only clocks. R/W clocks are supposed
to provide it, but it does not hurt check it.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
platform_get_resource() may return NULL, add proper
check to avoid potential NULL dereferencing.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap(e1, res->start, e2);
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Fixes the following sparse warning:
drivers/clk/meson/axg.c:260:25: warning:
symbol 'axg_gp0_params_table' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
In case of error, the function devm_ioremap() returns NULL pointer
not ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 78b4af312f ("clk: meson-axg: add clock controller drivers")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
"rem * SDM_DEN" can easily overflow on the 32-bit Meson8 and Meson8b
SoCs if the "remainder" (after the division operation) is greater than
262143Hz. This is likely to happen since the input clock for the MPLLs
on Meson8 and Meson8b is "fixed_pll", which is running at a rate of
2550MHz.
One example where this was observed to be problematic was the Ethernet
clock calculation (which takes MPLL2 as input). When requesting a rate
of 125MHz there is a remainder of 2500000Hz.
The resulting MPLL2 rate before this patch was 127488329Hz.
The resulting MPLL2 rate after this patch is 124999103Hz.
Commit b609338b26 ("clk: meson: mpll: use 64bit math in
rate_from_params") already fixed a similar issue in rate_from_params.
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Make the spinlock more specific, so better for lockdep
debugging and ctags/grep.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Remove CLK_IGNORE_UNUSED from mmc clocks. This was only needed while the
mmc driver incorrectly used the xtal as source instead of the mmc
clock. Now, the driver takes the correct clock, CCF is aware that the
clock is being used and we can remove this flag.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
According to the datasheet, in Meson-GXBB/GXL series,
The clock gate bit for SARADC is HHI_GCLK_MPEG2 bit[22],
while clock gate bit for SANA is HHI_GCLK_MPEG0 bit[10].
Test passed at gxl-s905x-p212 board.
The following published datasheets are wrong and should be updated
[1] GXBB v1.1.4
[2] GXL v0.3_20170314
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Tested-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The Amlogic Meson GX SoCs needs these two clocks to power up the
VPU power domain.
These two clocks are similar to the MALI clocks by having a glitch-free
mux and two similar clocks with gate, divider and muxes.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: removed the CLK_IGNORE_UNUSED on muxes and dividers]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the clkids for the clocks feeding the Video Processing Unit.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The CEC 32K AO Clock is a dual divider with dual counter to provide a more
precise 32768Hz clock for the CEC subsystem from the external xtal.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Switch the aoclk driver to use the new bindings and switch all the
registers access to regmap only.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Input source 0 of the mmc controllers is not directly xtal, as currently
described in DT. Each controller is fed by a composite clock (the usual
mux, divider and gate). The muxes inputs are the xtal (default) and the
fclk_div clocks. These parents, along with the divider, should be able to
provide the necessary rates for mmc and nand operation.
The input muxes should also be able to take mpll2, mpll3 and gp0_pll but
these are precious clocks, needed for other usage. It is better if the
mmc does not use these them. For this reason, mpll2, mpll3 and gp0_pll is
not listed among the possible parents.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 3c277c247e ("clk: meson: gxbb: add cts_mclk_i958")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
CLK_DIVIDER_ROUND_CLOSEST was incorrectly put in the hw.init flags
while it should have been in the divider flags
Fixes: 4087bd4b21 ("clk: meson: gxbb: add cts_amclk")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The clock controller also includes some reset lines. This patch
implements a reset controller to assert and de-assert these resets.
The reset controller itself is registered early (through
CLK_OF_DECLARE_DRIVER) because it is needed very early in the boot
process (to start the secondary CPU cores).
According to the public S805 datasheet there are two more reset bits
in the HHI_SYS_CPU_CLK_CNTL0 register, which are not implemented by
this patch (as these seem to be unused in Amlogic's vendor Linux kernel
sources and their u-boot tree):
- bit 15: GEN_DIV_SOFT_RESET
- bit 14: SOFT_RESET
All information was taken from the public S805 Datasheet and Amlogic's
vendor GPL kernel sources. This patch is based on an earlier version
submitted by Carlo Caione.
Suggested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the clkids for the clocks feeding the input0 of the mmc controllers
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Expose all clocks which maybe used as DT bindings
Only clock ids internal the controller remain un-exposed (none on this
particular controller at the moment)
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
gxbb clock driver gracefully handles case where the clkid is defined but
the clock hw pointer is not provided, as long as it is not at the end of
the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: a70c6e06ed ("clk: meson: gxbb: protect against holes in the onecell_data array")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
meson8b clock driver gracefully handles case where the clkid is defined
but the clock hw pointer is not provided, as long as it is not at the end
of the hw_onecell_data array.
This patch ensure that the last entries are defined as well to handle
this particular case.
Fixes: e92f7cca44 ("clk: meson8b: clean up fixed rate clocks")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
mpll0 clock is special compared to the other mplls. It needs another
bit (ssen) to be set to activate the fractional part the mpll divider
Fixes: 007e6e5c5f ("clk: meson: mpll: add rw operation")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=0BO9
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clk driver updates from Jerome Brunet:
* Expose more clock gate on meson8 (SAR ADC, RNG, USB, SDIO, ETH)
* Add new compatible to the meson8 clock controller for meson8b
* Add missing parents to gxbb clk81
* tag 'meson-clk-for-4.13-2' of git://github.com/BayLibre/clk-meson:
clk: meson: gxbb: add all clk81 parents
clk: meson: meson8b: add compatibles for Meson8 and Meson8m2
clk: meson8b: export the ethernet gate clock
clk: meson8b: export the USB clocks
clk: meson8b: export the gate clock for the HW random number generator
clk: meson8b: export the SDIO clock
clk: meson8b: export the SAR ADC clocks
Remove the FIXME on clk81 mux and add all the documented parents
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller on Meson8, Meson8b and Meson8m2 is very similar
based on the code from the Amlogic GPL kernel sources. Add separate
compatibles for each SoC to make sure that we can easily implement
all the small differences for each SoC later on.
In general the Meson8 and Meson8m2 seem to be almost identical as they
even share the same mach-meson8 directory in Amlogic's GPL kernel
sources.
The main clocks on Meson8, Meson8b and Meson8m2 are very similar,
because they are all using the same PLL values, 90% of the clock gates
are the same (the actual diffstat of the mach-meson8/clock.c and
mach-meson8b/clock.c files is around 30 to 40 lines, when excluding
all commented out code).
The difference between the Meson8 and Meson8b clock gates seem to be:
- Meson8 has AIU_PCLK, HDMI_RX, VCLK2_ENCT, VCLK2_ENCL, UART3,
CSI_DIG_CLKIN gates which don't seem to be available on Meson8b
- the gate on Meson8 for bit 7 seems to be named "_1200XXX" instead
of "PERIPHS_TOP" (on Meson8b)
- Meson8b has a SANA gate which doesn't seem to exist on Meson8 (or
on Meson8 the same bit is used by the UART3 gate in Amlogic's GPL
kernel sources)
None of these gates is added for now, since it's unclear whether these
definitions are actually correct (the VCLK2_ENCT gate for example is
defined, but only used in some commented block).
The main difference between all three SoCs seem to be the video (VPU)
clocks. Apart from different supported clock rates (according to vpu.c
in mach-meson8 and mach-meson8b from Amlogic's GPL kernel sources) the
most notable difference is that Meson8m2 has a GP_PLL clock and a mux
(probably the same as on the Meson GX SoCs) to support glitch-free
(clock rate) switching.
None of these VPU clocks are not supported by our mainline meson8b
clock driver yet though.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the ethernet gate clock to the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the USB related clocks (for the USB controller and the USB2 PHYs)
so they can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This exports the clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the SDIO clock so it can be used in the dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Export the clocks for the SAR ADC so they can be used in the
dt-bindings.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
These can be marked as const * const.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8rsv
-----END PGP SIGNATURE-----
Merge tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson into clk-next
Pull Amlogic clock driver updates from Jerome Brunet:
* Expose more i2s and spdif output clocks
* Expose EE uart and SPICC gate clocks
* Remove cpu_clk from to gxbb
* Mark clk81 as critical on gxbb
* Add CEC EE clocks
* tag 'meson-clk-for-4.13' of git://github.com/BayLibre/clk-meson:
clk: meson-gxbb: Add EE 32K Clock for CEC
clk: gxbb: remove CLK_IGNORE_UNUSED from clk81
clk: meson: meson8b: mark clk81 as critical
clk: meson: gxbb: remove the "cpu_clk" from the GXBB and GXL driver
clk: meson-gxbb: un-export the CPU clock
clk: meson-gxbb: expose UART clocks
clk: meson-gxbb: expose SPICC gate
clk: meson-gxbb: expose spdif master clock
clk: meson-gxbb: expose i2s master clock
clk: meson-gxbb: expose spdif clock gates
On Amlogic GX SoCs, there is two CEC controllers :
- An Amlogic CEC custom in the AO domain
- The Synopsys HDMI-TX Controller in the EE domain
Each of these controllers needs a 32.768KHz clock, but there is two paths :
- In the EE domain, the "32k_clk" this patchs is adding
- In the AO domain, with a more complex dual divider more precise setup
The AO 32K clock support will be pushed later in the corresponding
gxbb-aoclk driver when the AE CEC driver is ready.
The EE 32k_clk must be pushed earlier since mainline support for CEC in the
Synopsys HDMI-TX controller is nearby.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[Rebased patch on top of last changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
clk81 already has CLK_IS_CRITICAL so CLK_IGNORE_UNUSED is not
necessary
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Disabling clk81 results in an immediate freeze of the whole system. This
can happen "accidentally" when the last child-clock of clk81 is disabled
(in this case the common clock framework also disables clk81, even if it
was only enabled indirectly before).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
It seems that the "cpu_clk" was carried over from the meson8b clock
controller driver. On Meson GX (GXBB/GXL/GXM) the registers which are
used by the cpu_clk have a different purpose (in other words: they don't
control the CPU clock anymore). HHI_SYS_CPU_CLK_CNTL1 bits 31:24 are
reserved according to the public S905 datasheet, while bit 23 is the
"A53_trace_clk_DIS" gate (which according to the datasheet should only
be used in case a silicon bug is discovered) and bits 22:20 are a
divider (A53_trace_clk). The meson clk-cpu code however expects that
bits 28:20 are reserved for a divider (according to the public S805
datasheet this "SCALE_DIV: This value represents an N+1 divider of the
input clock.").
The CPU clock on Meson GX SoCs is provided by the SCPI DVFS clock
driver instead. Two examples from a Meson GXL S905X SoC:
- vcpu (SCPI DVFS clock 0) rate: 1000000000 / cpu_clk rate: 708000000
- vcpu (SCPI DVFS clock 0) rate: 1512000000 / cpu_clk rate: 708000000
Unfortunately the CLKID_CPUCLK was already exported (but is currently
not used) to DT. Due to the removal of this clock definition there is
now a hole in the clk_hw_onecell_data (which is not a problem because
this case is already handled in gxbb_clkc_probe).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The CPU clock defined in the Meson GX clock driver is actually a
left-over from the Meson8b clock controller. Un-export the clock so we
can remove it from the driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock ids of the three none AO uarts to the dt-bindings
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Helmut Klein <hgkr.klein@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy the commit message to match similar change]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the SPICC gate clock to enable the SPICC controller.
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[tidy commit message to match similar changes]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the spdif master clock and the mux to select the appropriate spdif
clock parent depending on the data source.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Expose the clock gates required for the spdif output
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
With CONFIG_RESET_CONTROLLER=n we see the following link error in the
meson gxbb clk driver:
drivers/built-in.o: In function 'gxbb_aoclkc_probe':
drivers/clk/meson/gxbb-aoclk.c:161: undefined reference to 'devm_reset_controller_register'
Fix this by selecting the reset controller subsystem.
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: Added fixes-by tag]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
to me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core, mostly
small non-critical fixes here and there as well as driver updates for new
and existing hardware support. The biggest things are the TI clk driver
rework to lay the groundwork for clkctrl support in the next merge window
and the AmLogic audio/graphics clk support.
Core:
* clk_possible_parents debugfs file so we know which parents a clk
could possibly have
* Fix to make clk rate change notifiers stop on the first failure instead
of continuing
New Drivers:
* Mediatek MT6797 SoCs
* hi655x PMIC clks
* AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
* Allwinner H5 SoCs and PRCM hardware
Updates:
* Nvidia Tegra T210 cleanups and non-critical fixes
* TI OMAP cleanups in preparation for clkctrl support
* Trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
* ZTE zx296718 SoC VGA clks
* Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
* Support for IDT VersaClock 5P49V5935
* Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJZE0YJAAoJEK0CiJfG5JUl9tEQAKVJx8VztYGt1REoFMtEEHmO
azhxT/uYGgdOMAr9a3mQxqfm5cJbjnb1EZj2RfC1XHs31BF66j40y9+5d8hY8Hzu
5IkY86s77TlqxGLwQcAsU75Q9cFrEW9X0KJ6OSzlrcc5hKlAEk/Z5lBKoQAm3mlU
JqD4DSyFqP0X3YSxV5R7yfarb/X3ekCiQ13EDrPRRhyvHUi6ReUJDDgbPHtA+O2c
ftLAARmxjzitzyvdXokXudkfNm8F5KePK+QkVikf6D/q+kx1D0BNJwZIjhpoiksn
z6LImLQ8l91AWghmqqpOFXolxQncPU+bJIL9Pox76p5b3EzbQuthIafiso8KsDST
4g3mHm42Yfx9uoF+U+pR8IeZfj5yQT91bvf8naPz/ngWMAlLP1IKJUvJN6jeTiwe
cO6GIec1OH40Xl7v/9EafMwDcnFG0cwQmzr/M6wi1dUlmbSygP9NOMTHlr6W/0wa
K2hCD6b5UHEgHmdfiJbZ2tKxLO0e8LABW+AU8fQH5S2eNe14vY0GvCzfAq5MArIz
QRpso/kdtGpTpwMEvV6PUmJ0IxYEjtNJVjGJYbORwios0SK0Xl6bJWf7gwn5crB6
nua9tVZtJEOHJS7S+ESp3VvuXj2/UGPoRRf5OsERo1S6ydGUQH+wDi1SJMdo/vtX
bIPzIw6WPxMp24JyKOhh
=/5a/
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"Sort of on the quieter side this time, which is probably due more to
me not catching up as quickly on patch review than anything else.
Overall it seems normal though, a few small changes to the core,
mostly small non-critical fixes here and there as well as driver
updates for new and existing hardware support.
The biggest things are the TI clk driver rework to lay the groundwork
for clkctrl support in the next merge window and the AmLogic
audio/graphics clk support.
Core:
- clk_possible_parents debugfs file so we know which parents a clk
could possibly have
- Fix to make clk rate change notifiers stop on the first failure
instead of continuing
New Drivers:
- Mediatek MT6797 SoCs
- hi655x PMIC clks
- AmLogic Meson SoC i2s and spdif audio clks and Mali graphics clks
- Allwinner H5 SoCs and PRCM hardware
Updates:
- Nvidia Tegra T210 cleanups and non-critical fixes
- TI OMAP cleanups in preparation for clkctrl support
- trivial fixes like kcalloc(), devm_* conversions, and seq_puts()
- ZTE zx296718 SoC VGA clks
- Rockchip clk-ids, fixups, and rename of rk1108 to rv1108
- IDT VersaClock 5P49V5935 support
- Renesas R-Car H3 and M3-W IMR clks and ES2.0 rev of R-Car H3
support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (151 commits)
clk: x86: pmc-atom: Checking for IS_ERR() instead of NULL
clk: ti: divider: try to fix ti_clk_register_divider
clk: mvebu: Use kcalloc() in two functions
clk: mvebu: Use kcalloc() in of_cpu_clk_setup()
clk: nomadik: Delete error messages for a failed memory allocation in two functions
clk: nomadik: Use seq_puts() in nomadik_src_clk_show()
clk: Improve a size determination in two functions
clk: Replace four seq_printf() calls by seq_putc()
clk: si5351: Delete an error message for a failed memory allocation in si5351_i2c_probe()
clk: si5351: Use devm_kcalloc() in si5351_i2c_probe()
clk: at91: Use kcalloc() in of_at91_clk_pll_get_characteristics()
reset: mediatek: Add MT2701 ethsys reset controller include file
clk: mediatek: add mt2701 ethernet reset
clk: hi6220: Add the hi655x's pmic clock
clk: ti: fix building without legacy omap3
clk: ti: fix linker error with !SOC_OMAP4
clk: hi3620: Fix a typo in one variable name
clk: hi3620: Delete error messages for a failed memory allocation in two functions
clk: hi3620: Use kcalloc() in hi3620_mmc_clk_init()
clk: hisilicon: Delete error messages for failed memory allocations in hisi_clk_init()
...
Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch of smaller
changes, but also some new platforms that are worth mentioning:
* Rockchip RK3399 platforms for Chromebooks, including Samsung Chromebook
Plus (Kevin)
* Orange Pi PC2 (Allwinner H5)
* Freescale LS2088A and LS1088A SoCs
* Expanded support for Nvidia Tegra186 (and Jetson TX2)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=q3Ix
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM 64-bit DT updates from Olof Johansson:
"Device-tree updates for arm64 platforms. Just as with 32-bit, a bunch
of smaller changes, but also some new platforms that are worth
mentioning:
- Rockchip RK3399 platforms for Chromebooks, including Samsung
Chromebook Plus (Kevin)
- Orange Pi PC2 (Allwinner H5)
- Freescale LS2088A and LS1088A SoCs
- Expanded support for Nvidia Tegra186 (and Jetson TX2)"
* tag 'armsoc-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (180 commits)
arm64: dts: Add basic DT to support Spreadtrum's SP9860G
arm64: dts: exynos: Use - instead of @ for DT OPP entries
arm64: dts: exynos: Add support for s6e3hf2 panel device on TM2e board
arm64: dts: juno: add information about L1 and L2 caches
arm64: dts: juno: fix few unit address format warnings
arm64: marvell: dts: enable the crypto engine on the Armada 8040 DB
arm64: marvell: dts: enable the crypto engine on the Armada 7040 DB
arm64: marvell: dts: add crypto engine description for 7k/8k
arm64: dts: marvell: add sdhci support for Armada 7K/8K
arm64: dts: marvell: add eMMC support for Armada 37xx
arm64: dts: hisi: add pinctrl dtsi file for HiKey960 development board
arm64: dts: hisi: add drive strength levels of the pins for Hi3660 SoC
arm64: dts: hisi: enable the NIC and SAS for the hip07-d05 board
arm64: dts: hisi: add SAS nodes for the hip07 SoC
arm64: dts: hisi: add RoCE nodes for the hip07 SoC
arm64: dts: hisi: add network related nodes for the hip07 SoC
arm64: dts: hisi: add mbigen nodes for the hip07 SoC
arm64: dts: rockchip: fix the memory size of PX5 Evaluation board
arm64: dts: hisilicon: add dts files for hi3798cv200-poplar board
dt-bindings: arm: hisilicon: add bindings for hi3798cv200 SoC and Poplar board
...
On Meson8b the MPLL parent clock (fixed_pll) has a rate of 2550MHz.
Multiplying this with SDM_DEN results in a value greater than 32bits.
This is not a problem on the 64bit Meson GX SoCs, but it may result in
undefined behavior on the older 32bit Meson8b SoC.
While rate_from_params was only introduced recently to make the math
reusable from _round_rate and _recalc_rate the original bug exists much
longer.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[as discussed on the ml, use DIV_ROUND_UP_ULL]
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
According to the public datasheet all register bits in HHI_MPLL_CNTL7,
HHI_MPLL_CNTL8 and HHI_MPLL_CNTL9 default to zero. On all GX SoCs these
seem to be initialized by the bootloader to some default value.
However, on my Meson8 board they are not initialized, leading to a
division by zero in rate_from_params as the math is:
(parent_rate * SDM_DEN) / ((SDM_DEN * 0) + 0)
According to the datasheet, the minimum n2 value is 4. The rate provided
by the clock when n2 is less than this minimum is unpredictable. In such
case, we report an error.
Although the rate_from_params function was only introduced recently the
original bug has been there for much longer. It was only exposed
recently when the MPLL clocks were added to the Meson8b clock driver.
Fixes: 1c50da4f27 ("clk: meson: add mpll support")
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
This adds the cts_i958 clock to control the clock source of the spdif
output block. This mux is not explicitly mentionned in the documentation
but it is critical to the spdif dai. It is used to select whether the clock
source of the spdif output is cts_amclk (when data are taken from i2s
buffer) or the cts_mclk_i958 (when data are taken from the spdif buffer)
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the spdif master clock also referred as cts_mclk_i958
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Add the i2s master clock also referred as cts_amclk
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The audio divider needs a specific clock divider driver.
With am mpll parent clock, which is able to provide a fairly precise rate,
the generic divider tends to select low value of the divider. In such case
the quality of the clock is very poor. For the same final rate, maximizing
the audio clock divider value and selecting the corresponding mpll rate
gives better results. This is what this driver aims to acheive. So far, so
good.
Cc: Hendrik v. Raven <hendrik@consetetur.de>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock controller is getting more complex and it might be possible, in
the future, to have holes in the clk_hw_onecell_data array. Just make sure
we skip those holes if it ever happens.
Acked-by: Michael Turquette <mturquette@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
The clock tree in the Amlogic GXBB and GXL/GXM SoCs is shared, but the GXL/GXM
SoCs embeds a different GP0 PLL, and needs different parameters with a vendor
provided reduced rate table.
This patch adds the GXL GP0 variant, and adds a GXL DT compatible in order
to use the GXL GP0 PLL instead of the GXBB specific one.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-4-git-send-email-narmstrong@baylibre.com
Tha Amlogic GXBB SoC GP0 PLL needs some vendor provided parameters to be
initializated in the the GP0 control registers before configuring the rate
with the rate table provided parameters.
GXBB GP0 PLL tweaks are also selected to respect the vendor init procedure.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-3-git-send-email-narmstrong@baylibre.com
In recent Amlogic GXBB, GXL and GXM SoCs, the GP0 PLL needs some specific
parameters in order to initialize and lock correctly.
This patch adds an optional PARAM table used to initialize the PLL to a
default value with it's parameters in order to achieve to desired frequency.
The GP0 PLL in GXBB, GXL/GXM also needs some tweaks in the initialization
steps, and these are exposed along the PARAM table.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490178747-14837-2-git-send-email-narmstrong@baylibre.com
The Mali is clocked by two identical clock paths behind a glitch free mux
to safely change frequency while running.
The two "mali_0" and "mali_1" clocks are composed of a mux, divider and gate.
Expose these two clocks trees using generic clocks.
Finally the glitch free mux is added as "mali" clock.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1490177935-9646-3-git-send-email-narmstrong@baylibre.com
Gxbb datasheet says N2 maximum value is 127 but the register field is
9 bits wide, the maximum value should 511.
Test shows value greater than 127, all the way to 511, works well
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-9-jbrunet@baylibre.com
Use read/write operations for the mpll clocks instead of the
read-only ones.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-7-jbrunet@baylibre.com
This patch adds new callbacks to the meson-mpll driver to control
and set the pll rate. For this, we also need to add the enable bit and
sdm enable bit. The corresponding parameters are added to mpll data
structure.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-6-jbrunet@baylibre.com
Until now, there was only 2 dividers and 2 muxes declared for the gxbb
platform. With the ongoing work on various subsystem, including audio,
this is about to change. Use the same approach as gates for dividers and
muxes, putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-5-jbrunet@baylibre.com
Until now, there was only 1 divider and 1 mux declared for the meson8b
platform. With the ongoing work on various system, including audio, this
is about to change. Use the same approach as gates for dividers and muxes,
putting them in tables to fix the register address at runtime.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-4-jbrunet@baylibre.com
parameter val is not enclosed in parenthesis which is buggy when given an
expression instead of a simple value
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20170309104154.28295-2-jbrunet@baylibre.com
Expose clock CLKID_RNG0 which is needed for the HW random number generator.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
This includes two branches for arm64 dt updates, both following up
on earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the
start of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=A3U6
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
This includes two branches for arm64 dt updates, both following up on
earlier changes for the same platforms that are already merged:
Samsung:
- add USB3 support in Exynos7
- minor PM related updates
Amlogic:
- new machines: WeTek Set-top-boxes
- various devices added to DT
There are also a couple of bugfixes that trickled in since the start
of the merge window:
- The moxart_defconfig was not building the intended platform
- CPU-hotplug was broken on ux500
- Coresight was broken on Juno (never worked)"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: deconfig: fix the moxart defconfig
ARM: ux500: resume the second core properly
arm64: dts: juno: update definition for programmable replicator
arm64: dts: exynos: Add regulators for Vbus and Vbus-Boost
arm64: dts: exynos: Add USB 3.0 controller node for Exynos7
arm64: dts: exynos: Use macros for pinctrl configuration on Exynos7
pinctrl: dt-bindings: samsung: Add Exynos7 specific pinctrl macro definitions
arm64: dts: exynos: Add initial configuration for DISP clocks for TM2/TM2e
ARM64: dts: meson-gxbb-p200: add ADC laddered keys
ARM64: dts: meson: meson-gx: add the SAR ADC
ARM64: dts: meson-gxl: add the pwm_ao_b pin
ARM64: dts: meson-gx: add the missing pwm_AO_ab node
clk: gxbb: fix CLKID_ETH defined twice
ARM64: dts: meson-gxl: rename Nexbox A95x for consistency
clk: gxbb: add the SAR ADC clocks and expose them
dt-bindings: amlogic: Add WeTek boards
ARM64: dts: meson-gxbb: Add support for WeTek Hub and Play
dt-bindings: vendor-prefix: Add wetek vendor prefix
ARM64: dts: meson-gxm: Rename q200 and q201 DT files for consistency
ARM64: dts: meson-gx: Add HDMI HPD/DDC pinctrl nodes
...
CLKID_ETH is define in the dt-bindings but has not be commented out in the
clock driver. Just do it now.
Fixes: 738f66d321 ("clk: gxbb: add AmLogic GXBB clk controller driver")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
During meson8b clock probe, clk81 register address is fixed twice.
First using the meson8b_clk_gates array, then by directly changing
meson8b_clk81 register.
As a result meson8b_clk81.reg = HHI_MPEG_CLK_CNTL + clk_base + clk_base.
Fixed by just removing the second fixup.
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The HHI_SAR_CLK_CNTL contains three SAR ADC specific clocks:
- a mux clock to choose between different ADC reference clocks (this is
2-bit wide, but the datasheet only lists the parents for the first
bit)
- a divider for the input/reference clock
- a gate which enables the ADC clock
Additionally this exposes the ADC core clock (CLKID_SAR_ADC) and
CLKID_SANA (which seems to enable the analog inputs, but unfortunately
there is no documentation for this - we just mimic what the vendor
driver does).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Export HDMI clock from internal to dt-bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
These updates have been kept in a separate branch mostly because
they rely on updates to the respective clk drivers to keep the
shared header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been
merged for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and
usb driver changes are required and included here, and also
the clk tree changes.
- The Allwinner platforms have seen a large-scale change to their
clk drivers and the dts file updates must come after that.
This includes the newly added Nextthing GR8 platform, which is
derived from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't
added until just before the merge window
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OmAu
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
I2C and AO_I2C clocks are needed for the i2c driver, expose to DT
(and comment out in clk driver)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
USB0_DDR_BRIDGE and USB1_DDR_BRIDGE1 are needed for the related
dwc2 usb controller. USB, USB0 and USB1 are needed for the PHYs.
Expose these clocks to DT and comment out in clk driver.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
SPI clock is needed for the spifc driver, expose to DT
(and comment out in the clk driver)
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This exposes the MPLL2 clock as this is one of the input clocks of the
ethernet controller's internal mux.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The addition of many gate clocks added two entries in an array for
the same value:
drivers/clk/meson/meson8b.c:479:10: error: initialized field overwritten [-Werror=override-init]
[CLKID_GCLK_VENCI_INT] = &meson8b_gclk_venci_int.hw,
[CLKID_GCLK_VENCI_INT] = &meson8b_gclk_vencp_int.hw,
This was clearly an accident, and since all other identifiers are
listed in the order in which they are defined, I'm changing the
first one to CLKID_GCLK_VENCI_INT0, making it all consistent again.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: e31a1900c1 ("meson: clk: Add support for clock gates")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the meson8b clock gates. Most of
them are disabled by Amlogic U-Boot, but need to be enabled
for ethernet, USB and many other components.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-7-git-send-email-serveralex@gmail.com
The macro used gxbb_ prefix for clock definitions. In order
to share the macro between gxbb and meson8b, the prefix must
be moved to gxbb.c.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-6-git-send-email-serveralex@gmail.com
Only expose future CLKID constants if necessary. This patch
removes CLK_NR_CLKS from the DT bindings but leaves all previously
defined CLKIDs there to keep backward compatibility.
Signed-off-by: Alexander Müller <serveralex@gmail.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/1472319654-59048-5-git-send-email-serveralex@gmail.com
sizeof() when applied to a pointer typed expression gives the
size of the pointer, not that of the pointed data.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Fixes: f8c11f7991 ("clk: meson: Add GXBB AO Clock and Reset controller driver")
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Adds a Clock and Reset controller driver for the Always-On part
of the Amlogic Meson GXBB SoC.
It exports paired Clocks and Resets lines that will be used by
peripherals in the Always-On subsystem.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add the SD/eMMC gate clocks and expose them for use by DT.
While at it, also explose FCLK_DIV2 since this is one of the input
clocks to the mux internal to each of the SD/eMMC blocks.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Use the builtin_platform_driver() macro to make the code simpler.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This reverts commit e16fb2e635.
Updated documentation from the chip vendor reveals that this clock is
not required for correct operation of the MMC controller. As such, do
not expose it to DT.
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The MMC_PCLK is needed for the SD/eMMC driver, expose to DT (and comment
out in clk driver)
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160707033837.20029-1-khilman@baylibre.com
The Kconfig currently controlling compilation of this code is:
drivers/clk/meson/Kconfig:config COMMON_CLK_GXBB
drivers/clk/meson/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE and ALIAS are no-op for non-modules.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-3-paul.gortmaker@windriver.com
The Kconfig currently controlling compilation of this code is:
drivers/clk/meson/Kconfig:config COMMON_CLK_MESON8B
drivers/clk/meson/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
However a recent commit added a bunch of modular boilerplate to this
driver.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Also note that MODULE DEVICE_TABLE/ALIAS are no-op when non-modular.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-amlogic@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Link: lkml.kernel.org/r/20160704211220.5685-2-paul.gortmaker@windriver.com
The gxbb clock controller is the primary clock generation unit for the
AmLogic GXBB SoC. It is clocked by a fixed 24MHz xtal, contains several
PLLs and the usual post-dividers, muxes, dividers and leaf gates that
are fed into various IP blocks in the SoC.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Fractional MPLLs are a superset of the existing AmLogic MPLLs. They add
in a couple of new bitfields for further dividing the clock rate to
achieve rates with fractional hertz.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
MPLLs are adjustable rate clocks derived from PLLs. On both Meson8b and
GXBB they appear to be only derived from fixed_pll.
Add support for these clock types so that they can be added to their
respective drivers.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
There are a series of peripheral and system gate clocks that fan out
from the clk81 signal. Add a helper macro to statically initialize these
gate clocks.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Break the AmLogic clock code up so that only the necessary parts are
compiled and linked. The core code is selected by both arm and arm64
builds with COMMON_CLK_AMLOGIC. The individual drivers have their own
config options as well.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This patch creates a proper platform_driver for the meson8b clock
controller. Use of CLK_OF_DECLARE is removed, and can be added back in
later if very early registration of some clocks is required.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the composite clock registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
To preserve git bisect this patch also flips the switch and starts using
of_clk_add_hw_provider instead of the deprecated meson_clk_register_clks
method. As a byproduct clk.c can be deleted.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
This clock is undocumented and always orphaned. Get rid of it until we
have more complete clock tree documentation.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the cpu clock registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
Ninja rename a5_clk to cpu_clk to better align with cpufreq convention.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the fixed factor registration function and helpers. Replace
unnecessary configuration struct with static initialization of the
desired clock type.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the pll registration function and helpers. Replace unnecessary
configuration struct with static initialization of the desired clock
type.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
Remove the fixed_rate registration function and helpers from clkc.[ch].
Replace unnecessary configuration struct with static initialization of
the desired clock type.
While we're here, begin the transition to a proper platform_driver and
call of_clk_add_hw_provider with a shiny new struct clk_hw_onecell_data.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
The register offsets in the data sheet are confusing. Document them more
thoroughly.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
As preparation for arm64 based mesongxbb, which pulls in this code once
enabling ARCH_MESON, fix a size_t vs. unsigned int type mismatch.
The loop uses a local unsigned int variable, so adopt that type,
matching the header.
Fixes: 7a29a86943 ("clk: meson: Add support for Meson clock controller")
Signed-off-by: Andreas Färber <afaerber@suse.de>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Clock provider drivers generally shouldn't include clk.h because
it's the consumer API. Only include clk.h if it's actually used.
Cc: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This error handling hopefully isn't needed but it make the static
checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds support for the basic clocks found on the Amlogic
Meson8b SoCs.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patchset adds the infrastructure for registering and managing the
core clocks found on Amlogic MesonX SoCs. In particular:
- PLLs
- CPU clock
- Fixed rate clocks, fixed factor clocks, ...
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
