[WHY]
On customer board, there is one pluse (1v , < 1ms) on
DDC_CLK pin when plug / unplug DP cable. Driver will read
it and config DP to HDMI/DVI dongle.
[HOW]
If there is a real dongle, DDC_CLK should be always pull high.
Try to read again to recovery this special case. Retry times = 3.
Need additional 3ms to detect DP passive dongle(3 failures)
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Skipping initial link training will result in no verified link cap for
mode enumeration. Some versions of the BIOS seem to have PHY programming
sequence issue as well if initial link training is skipped, resulting in
a softlock in BIOS command table.
[How]
Identify the empty dongle hotplug case, and still do initial link
training.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In 99% user case, edp will be post by vbios.
In 1% / current case: Lenovo don't light up edp panel in vbios
post stage, vbios won't be lit up. Thus in dal when we init DCN
10 hw, we power up edp, then we start detect_sink, but internal
time is too short, when we detect it, HPD is still low, so we don't
detect the edp, and edp shows black.
[How]
When we init hw, we wait edp HPD to high after power up edp.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An earlier change added update of interdependent dlg/ttu params for pipes
not being updated in the current call. The code fails to check if the other
pipes are actually active yet causing an assert.
This change adds a check for surface presence on the pipes before updating
the interdepenednt params.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
YCbCr420 packing format uses two chanels for luma, and 1
channel for both chroma component. Our previous implementation
did not account for this and results in every other pixel having
very high luma value, showing greyish color instead of black.
YCbCr444 = <Y1, Cb1, Cr1>; <Y2, Cb2, Cr2> .....
YCbCr420 = <Y1, Y2, Cb1>; <Y3, Y4, Cr1> .....
[How]
Program the second channel with the black color value for luma
as well.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC warns when a REG_WAIT takes a while and full-on errors
with stack dump on REG_WAIT timeout. Most of the time it isn't
a real issue.
[How]
Make DC cool its jets - taking a while is a debug message (because
it is not something that normal users should need to be aware of),
and timeouts are warnings (because it technically shouldn't
happen, but it's not a big deal if it does)
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is a dual channel format and should be treated like other
video formats
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In certain configurations, such as PX configs or some Vega20 parts
DC gets created without connectors.
[How]
Drop the dm_error print when no connectors.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When XGMI is enabled, the DP reference clock needs to be adjusted
according to the XGMI spread spectrum percentage and mode. But first,
we need the ability to fetch this info.
[How]
Within the BIOS parser, Read from vBIOS when XGMI SS info is requested.
In addition, diags build uses include_legacy/atomfirmware.h for the
smu_info_v3_3 table headers. Update that as well.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need a way to differentiate Vega 20 in DC
[How]
Add a DCE_VERSION_12_1 enum, which will be returned as the DC version if
the ASIC used is a Vega 20.
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The visual corruption due to low display clock value observed on some
systems
[How]
There was earlier patch for dspclk:
'drm/amd/display: Raise dispclk value for dce_update_clocks'
Adding +15% workaround also to to dce112_update_clocks
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Leo Li <Sunpeng.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Tracing is a useful and cheap debug functionality
[How]
This creates a new trace system amdgpu_dm, currently with
three trace events
amdgpu_dc_rreg and amdgpu_dc_wreg report the address and value
of any dc register reads and writes
amdgpu_dc_performance requires at least one of those two to be
enabled. It counts the register reads and writes since the
last entry
v2: Don't check for NULL before kfree
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To prepare for clock debug logging. With the exception of removing
max_supported_dppclk_khz from logs, there are no functional changes.
[How]
Add clk_bypass struct and clean up buffer logic
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Fatemeh Darbehani <Fatemeh.Darbehani@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dce100 was set to always pass safe_to_lower = false
to the clock manager
Thus, on suspend the clocks were not being set to 0
which is incorrect behaviour
This was causing s3 resume to blackscreen on intel
CPUs with dce100 GPUs attached
(Note that the hash in this Fixes: tag is the hash on Alex's tree)
Fixes: ae7d8aeb38d7 ("drm/amd/display: remove safe_to_lower flag from dc, use 2 functions instead")
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dithering needs to be enabled or disabled as requested. If
dc_stream_update->dither_option is non-null, program the FMT blocks.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
add customizable log with a message input, which is for adding
test log in debugging as printf function in ETW.
[Usage]
EVENT_LOG_CUST_MSG1("TestLog","Hello World %d=0x%x", 123, pDC);
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For more clear usage in future
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY] fbc is within the data path from memory to dce. while
re-configure mc dmif, fbc should be enabled. otherwise, fbc
may not be enabled properly.
[HOW] before re-configure mc dmif, disable fbc, only after
dmif re-configuration fully done, enable fbc again.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
* Use provided infopacket in stream (if valid) instead of reconstructing
in set_vendor_info_packet()
* Use proper format for enums
* Use dc info packet struct instead
Signed-off-by: Harmanprit Tatla <Harmanprit.Tatla@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Failure to read Detailed Capabilities Info.
[How]
Read Detailed Capbilities Info 80h-08Fh.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This patch is for use by dm, no need for it in dc.
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are a lot of unintuitive parts of the dm-dc interface.
It would help us if these were documented to provide
a common understanding of what they are supposed to do
[How]
Most of this documentation is stubs, to be filled out more
thoroughly by the experts
Not every dm-accessible function and struct is mentioned.
Simple functions like getters, setters, retain, release,
create, destroy can be left unadorned.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Shahin Khayyer <Shahin.Khayyer@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When there are multiple aux transaction in parallel, it is sometime
sporadically the aux transaction starts to continuously fail. The
aux transaction was failing because the busy bit for the given gpio
pin was always set. The busy bit was alway set because the
programming sequence to read, modify and write busy bit was not
atomic. Due to which when multiple threads are trying to modify the
busy bits for their gpio pins in the same integer variable sometimes
the busy bits integer variable is written with old data causing
failure.
[how]
Instead of using individual bits to track gpio pins and grouping
them to integers, one byte will be allcoated for each gpio pin.
Now whenever a gpio pin needs to be set to mark being used, only
writing a value of one to that byte is sufficient, other bytes
are not impacted. Also no need to have atomicity with bytes unlike
with bits.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
More than 4x4K didn't lightup on Vega20 due to low dcfclk value.
Powerplay expects valid min requirement for dcfclk from DC.
[How]
Update min_dcfclock_khz based on min_engine_clock value.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dce/dce_mem_input.h which is included more than once
Signed-off-by: Brajeswar Ghosh <brajeswar.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adaptive Backlight Management (ABM) is a feature
that reduces backlight level to save power, while
increasing pixel contrast and pixel luminance
to maintain readability and image quality.
ABM will adjust in response to the
pixel luminance of the displayed content.
ABM is made available as a drm property on eDP
monitors called "abm level", which ranges from 0 to 4.
When this property is set to 0, ABM is off. Levels 1
to 4 represent different ranges of backlight reduction.
At higher levels both the backlight reduction and pixel
adjustment will be greater.
ABM requires DMCU firmware, which is currently available for
Raven ASICs only. If the feature does not work, please
ensure your firmware is up to date.
v2:
Fix commit message, only attach property if DMCU loaded
v3:
Store ABM level in crtc state to accommodate dc
v4:
Fix ABM saving on dpms cycle
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DMCU IRAM must be loaded by the driver before DMCU
can function.
Move the IRAM code out of the shadows and into a new file
modules/power/power_helpers.c
The IRAM table contains the backlight curve and ABM parameters
Add this new file to the Makefiles
Call dmcu_load_iram in late init of DM
Move struct dmcu_version from dc.h to dmcu.h to allow
dmcu to be included on its own
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There was a full clock request struct of which only
one value was being used.
[How]
Replace the struct with a uint32_t
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_link_set_backlight_level can be called from a context
where the stream is unknown. In this case, we can still
find which controller is driving this particular backlight
[How]
Compare links for equality instead of streams
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
expose dcn10_get_surface_visual_confirm_color() to be used in the
future
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A number of registers need to be updated for all active
pipes wherever any pipe causes a change in watermarks.
This change separates programming of these registers into
a separate function call that is called for all active pipes
during a bw update.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We observed an issue where a display would not accept programming of
the ignore_MSA_timing_param bit if the stream was blanked.
[How]
move enable_stream_features from enable_link_dp to
core_link_enable_stream, after unblank_stream
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For some complicated blending transition cases, the head
pipe of the second stream may end up being a higher pipe
index than the free pipe. In those cases dc_add_plane_to_context
will incorrectly set the tail_pipe to the free pipe, which
will cause the top_pipe and bottom_pipe to be the same
[How]
Move the call to resource_get_tail_pipe_for_stream() to be
before call to acquire_free_pipe_for_stream().
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DPCD Extended Receiver Capability Field
[Why]
1.dpcd extended receiver capability sometimes read fail,
and corrupted data leads to sink caps is not correct.
2.sometimes sink reply ack with fewer data
[How]
check the return value of core_link_read_dpcd,
try to read again when failure happens
Signed-off-by: Xiaodong Yan <Xiaodong.Yan@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change the math to work in viewport rotation when calculating
viewport and viewport adjustment. This simplifies the math
for viewport calculation and makes viewport adjustment easier to
understand.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Underflow is asserted due to some timing condition which does not
actually result in visible underflow (i.e. it occurs while blanked).
[how]
Force clear underflow occured bit whenver we unblank.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The condition to check for two pixels per containter has become rather
long and is used in number of places.
[how]
Move the check to a helper function.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
phy_pix_clk is one of the variable used to check if one PLL can be shared
with displays having common mode set configuration. As of now
phy_pix_clock varialbe is calculated in function dc_validate_stream().
dc_validate_stream() function is called after clocks are assigned for the
new display. Due to this during hotplug, when PLL sharing conditions are
checked for new display phy_pix_clk variable will be 0 and for displays
that are already enabled phy_pix_clk will have some value. Hence PLL will
not be shared and if the display hardware doesn't have any more PLL to
assign, mode set will fail due to resource unavailability.
[how]
Instead of only calculating the phy_pix_clk variable after the PLL is
assigned for new display, this patch calculates phy_pix_clk also during
the before assigning the PLL for new display.
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohanmarimuthu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Typo for return check value.
[How]
Correct one should be "return enable ? true : false;"
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCU firmware is not required - the system is expected to run
fine without it. Therefore, wherever dmcu functions could be
called, dmcu initialization shoudl be checked
[How]
Use the helpful hook dmcu_funcs->is_dmcu_initialized
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Gamma was always being set as identity on SDR monitor,
leading to no changes in gamma. This caused nightlight to
not apply correctly.
[how]
Added a default gamma structure to compare against
in the sdr case.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HUBP underflow is never cleared, which causes underflow in one
test to fail another test, violating the independence requirements
[how]
Rather than make clearing implicit, we explicitly clear underflow
status in DTN.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_add_stream_to_context is used to check bw requirement.
It is not an error if it fails.
[How]
Replace DC_ERROR with DC_LOG_WARNING.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_state has an array of dc_stream_status that contain
pointers to the dc_plane_state and other useful information
Confusingly, dc_stream_state also contains a dc_stream_status
called status. This struct was partially initialized and
used in a few places
[How]
stream->status.link has been replaced with stream->sink->link.
If a stream does not have a sink, or a sink does not have a link,
something has gone seriously wrong
All other properties of stream->status were zeroed by kzalloc
and never initialized, so they have been replaced by the number 0
This is a refactor: no functional change is intended
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Tony Cheng <Tony.Cheng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Causes a black screen on a Stoney laptop.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=108577
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add FBC to the list of features that can be enabled from the DM.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The value is dependent on whether fbc is available.
v2: only check if num_pipes is valid
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
RETIMER_REDRIVER_INFO shows the buffer as a decimal value with a '0x'
prefix, which is somewhat misleading.
Fix it to print hexadecimal, as was intended.
Fixes: 2f14bc89("drm/amd/display: add retimer log for HWQ tuning use.")
Cc: Charlene Liu <charlene.liu@amd.com>
Cc: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need to disable EDP backlight when enter S4 with EDP only
and resume from S4 with secondary only.
[How]
Align the real hw and sw state via vBios scratch register in
function enable_accelerated_mode when resume from S4.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When going to full-screen mode commit_planes_for_stream tries to decrease
dcf_deep_sleep value, but safe_to_lower is false, so we don't send the new value
to SMU but dc context gets updated.
Later when dc_post_update_surfaces_to_stream tries to lower dcf_ds when
safe_to_lower is true, this check prevents the message from being sent.
[How]
Remove the check that compares new value with what is stored in dc_context.
This check is not necessary as dcn1_update_clocks already checks if the value
is different from the current dcf_dp value.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
This is based on HW programming guide update.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DM may want to understand any backlight optimizations
applied, so DM needs a way to query from the HW both
the real current backlight, which may be value during
transition.
And also target backlight, which may be after some
backlight optimizations applied.
[How]
Add interface to query current and target backlight levels
Target level may indicate backlight level after backlight
optimization and reductions are applied.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Curretly dc will incorrectly calculate viewport when there is
rotation or mirror being applied
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Su Chung <Su.Chung@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DC to SMU calls, with minimal interference from
pplib.
The reason for each pp_smu interface mapping to 1 SMU message is so we
can have the sequencing of different SMU message in DC and shared across
different OS's.
This will also simplify debugging as DAL owns this interaction and
there's no confusion about division of ownership.
[How]
Part 4: Change clock units so they match the values PPLib sends to SMU.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] On DCN1/DCE, There are two functions programming OCSC:
program_csc_matrix and program_output_csc. They do the same thing.
[How] Consolidate to use only program_output_csc.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
variableNamingsLikeSo aren't to convention. use_this_instead.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] We want to increase precision for backlight setting.
But DC interface takes 8 bit backlight level value only.
[How] DMCU already takes 16 bit backlight level.
Expand the DC interface to take 16.16 bit value.
Max 32 bit backlight value (0xFFFF) will represent
max backlight (100%)
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They are no longer relevant
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Steven Chiu <steven.chiu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Coverity found various high-impact issues that need resolving.
[How]
Fix some buffer overruns and uninitialized variables.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We do not need to adjust surface scaling when p2i is enabled
and we do not support interlaced timing otherwise
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Gabe's formula sometimes uses values from non-existent 'unsupported'
state to do validation.
This change adds this extra state so validation can work correctly.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Set gamma not working on certain planes in MPO configuration
Root cause is that video format (YUV-420) isn't allowed for IGAM where
gamma is applied.
Fix is not easy though:
1. allowing will not work because IGAM is before ICSC so RGB gamma would
be applied on YUV pixels.
2. Moving OS gamma to DGAM or RGAM resulted in weird artifacts.
Ultimately the root cause for these artifacts was due to handling end
points and the fact that YUV->RGB conversion will frequently "overshoot"
FP 1.0 value. DCE has a single end point and slope, so we would take max.
In nightlight mode, blue channel is reduced, sometimes to flat 0 line,
but red is virtually unchanged. Any "overshot" in blue will be clipped
to 1 (max R,G,B) instead of max blue value.
[How]
Fortunately, this can be fixed on DCN where we have end point and slope
for all three color channels. We cannot fix this problem on DCE.
Other things fixed:
- switch (back) to using RGAM for OS gamma instead of IGAM
- add coeffs for 709 YUV->RGB (we used RGB->YUV for both conversions)
- switch color temperature method to scaled bradford - otherwise we would
have clipping problems that caused us to switch to IGAM for OS gamma
in the first place.
- comments and some minor improvements - there are some more issues but
they will be addressed in separate commits.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as
possible interference by pplib. The reason for each pp_smu interface
mapping to 1 SMU message is so we can have the sequencing of different
SMU message in dal and shared across different OS. This will also
simplify debugging as DAL owns this interaction and there's no
confusion about division of ownership.
[How]
Separate the set_hard_min_fclk_by_freq message from the
SMU messages that are sent as part of pp_rv_set_display_requirement.
directly notify min dcfclk to smu part 2
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
TG in pipe_ctx stream resource is not null where used in
commit_planes_do_stream_update since it is assigned the
same time the stream is set in pipe_ctx - when the pipe is
acquired. This null check produced a static code analysis
warning and should be removed to avoid similar unnecessary
checks in the future.
[How]
Remove the null check.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds the hw block as well as hooks up dppclk dto
programming
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for adding the actual dccg block since the
current implementation of dccg is mor eof a clock manager
than a hw block
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as possible
interference by pplib. The reason for each pp_smu interface mapping to
1 SMU message is so we can have the sequencing of different SMU message
in dal and shared across different OS. This will also simplify
debugging as DAL owns this interaction and there's no confusion about
division of ownership.
[How]
Part 2: Separate set_min_deep_sleep_dcfclk message from the SMU
messages that are sent as part of dm_pp_apply_clock_for_voltage_request.
Directly notify min dcfclk to smu
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In DCN we want direct DAL to SMU calls, with as little as possible
interference by pplib. The reason for each pp_smu interface mapping
to 1 SMU message is so we can have the sequencing of different SMU
message in dal and shared across different OS. This will also simplify
debugging as DAL owns this interaction and there's no confusion about
division of ownership.
[How]
Part 1: Separate set_min_deep_Sleep_dcfclk message from the SMU
messages that are sent as part of dcn10_pplib_apply_display_requirements.
Notify deep sleep dcfclk to smu directly
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need separate feature flag for DP 4:2:0 support, since existing
flag is used for HDMI
[How]
Added dp_ycbcr420_supported to struct encoder_feature_support
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previous logic to update display count in commit_planes_do_stream_update
doesn't cover all cases.
[How]
Update display count as part of clock updates. Count virtual stream
as active to work around headless situation.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Make these functions non static and define registers for future use
is_lower_pipe_tree_visible();
is_upper_pipe_tree_visible();
is_pipe_tree_visible();
dcn10_program_pte_vm();
set_hdr_multiplier();
update_dchubp_dpp()
find_top_pipe_for_stream()
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dc_transfer_func structs were being passed around with a null
pointer, waiting for unsuspecting programmers to dereference it.
[How]
Initialize it
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Freesync 2 HDR and support for HDR content
outside the range of the HDR display
require implementation on Dal 3 to better match
Dal2.
[How]
Add support for Freesync HDR and mapping
of source content to display ranges for better
representation of HDR content.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dccg contains code related to every dcn revision in
a single file.
This change splits out the dcn parts of code into correct folders
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Move things not accessed outside dccg block into dce specific
struct
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to keep things more readable, avoids a true/false flag
in dc interface layer.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is done to clear up the clock programming sequence
since the only time we need to notify pplib is after
clock update.
This also renames the clk block to dccg, at the moment
this block contains both clock management and dccg
functionality.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When vstartup is larger than vblank end we need to set v_fp2
to allow for this early start
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=5lmL
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Dave Airlie:
"Pretty much a normal fixes pull pre-rc1, mostly amdgpu fixes, one i915
link training regression fix, and a couple of minor panel/bridge fixes
and a panel quirk"
* tag 'drm-next-2018-11-02' of git://anongit.freedesktop.org/drm/drm: (37 commits)
drm/amdgpu: revert "enable gfxoff in non-sriov and stutter mode by default"
drm/amd/pp: Print warning if od_sclk/mclk out of range
drm/amd/pp: Fix pp_sclk/mclk_od not work on Vega10
drm/amd/pp: Fix pp_sclk/mclk_od not work on smu7
drm/amd/powerplay: no MGPU fan boost enablement on DPM disabled
drm/amdgpu: Fix skipping hangged job reset during gpu recover.
drm/amd/powerplay: revise Vega20 pptable version check
drm/amd/display: set backlight level limit to 1
drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
dt-bindings: drm/panel: simple: Innolux TV123WAM is actually P120ZDG-BF1
drm/bridge: ti-sn65dsi86: Remove the mystery delay
drm/panel: simple: Add "no-hpd" delay for Innolux TV123WAM
drm/panel: simple: Support panels with HPD where HPD isn't connected
dt-bindings: drm/panel: simple: Add no-hpd property
drm/edid: Add 6 bpc quirk for BOE panel.
drm/amdgpu: fix reporting of failed msg sent to SMU (v2)
drm/amdgpu: Fix compute ring 1.0.0 failure after reset
drm/amdgpu: fix VM leaf walking
drm/amdgpu: fix amdgpu_vm_fini
drm/amd/powerplay: commonize the API for retrieving current clocks
...
Pull AFS updates from Al Viro:
"AFS series, with some iov_iter bits included"
* 'work.afs' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (26 commits)
missing bits of "iov_iter: Separate type from direction and use accessor functions"
afs: Probe multiple fileservers simultaneously
afs: Fix callback handling
afs: Eliminate the address pointer from the address list cursor
afs: Allow dumping of server cursor on operation failure
afs: Implement YFS support in the fs client
afs: Expand data structure fields to support YFS
afs: Get the target vnode in afs_rmdir() and get a callback on it
afs: Calc callback expiry in op reply delivery
afs: Fix FS.FetchStatus delivery from updating wrong vnode
afs: Implement the YFS cache manager service
afs: Remove callback details from afs_callback_break struct
afs: Commit the status on a new file/dir/symlink
afs: Increase to 64-bit volume ID and 96-bit vnode ID for YFS
afs: Don't invoke the server to read data beyond EOF
afs: Add a couple of tracepoints to log I/O errors
afs: Handle EIO from delivery function
afs: Fix TTL on VL server and address lists
afs: Implement VL server rotation
afs: Improve FS server rotation error handling
...
[Why]
Carrizo and Stoney have severe corruption when trying to power
4k 60 monitors over HDMI connectors that support 4k 60.
Carrizo and Stoney require retimers and redrivers to support 4k 60
over HDMI. This driver does not currently support these. Thus, 4k 60
HDMI (and all other modes requiring over 300MHz) should be disabled.
[How]
Reduce the dce11 HDMI pixel clock cap to 300000kHz.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove the undefinition of READ and WRITE because these constants may be
used elsewhere in subsequently included header files, thus breaking them.
These constants don't actually appear to be used in the driver, so the
undefinition seems pointless.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: David Howells <dhowells@redhat.com>
RV2 resource is limit to 3 pipes. Limitation should apply to all HW
blocks instead of front pipe.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Wrong index for pstate debug test register
[How]
Add correct index value for dcn1_01 in hubbub1_construct()
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Roman Li <Roman.Li@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clang warns when one enumerated type is implicitly converted to another.
drivers/gpu/drm/amd/amdgpu/../display/dc/dce/dce_aux.c:315:19: warning:
implicit conversion from enumeration type 'enum
aux_channel_operation_result' to different enumeration type 'enum
aux_transaction_reply' [-Wenum-conversion]
reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/gpu/drm/amd/amdgpu/../display/dc/i2caux/dce110/aux_engine_dce110.c:349:19:
warning: implicit conversion from enumeration type 'enum
aux_channel_operation_result' to different enumeration type 'enum
aux_transaction_reply' [-Wenum-conversion]
reply->status = AUX_CHANNEL_OPERATION_FAILED_HPD_DISCON;
~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
The current enum is incorrect, it should be from aux_transaction_reply,
so use AUX_TRANSACTION_REPLY_HPD_DISCON.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DISPCLK value was previously requested to be 15% higher for all
ASICS that went through the dce110 bandwidth code path. As part of a
refactoring of dce_clocks and dce110 set_bandwidth this was removed
for power saving considerations.
This changed caused corruption under certain display configurations.
Originally thought to be Vega specific, it was also observed on Polaris.
[How]
The 15% is brought back but its placement differs from the original
patch. This boost should only be enable while DFS bypass is inactive.
This (like the Vega patch) is also a workaround that should be
removed after the root cause is identified.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Due to a small pre-fetch window, the active vline timing is a couple
of lines off when compared to what it should be.
[How]
Changed the calculation for the start vline to account for this window.
Signed-off-by: Murton Liu <murton.liu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description] interlace mode shows wrong vertical timing.
Interface timing in Edid is half vertical timing as progressive timing.
driver doubled the vertical timing in edid_paser,
no need to double in optc again.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
ddc engines were recently changed to be independently tracked
from pipe count. the change was reflected in resource constructor
but not in destructor. this manifests as a memory leak when
pipe harvesting is enabled, since not all constructed ddc engines
are freed
[how]
make destructor symmetric with constructor for all dcX_resource
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DF keeps awake after S0i3 resume due to DRAM_STATE_CNTL
is set by bios command table during dcn init_hw.
[How]
As a work around, check STATE_CNTL status before init_hw,
if it is 0 before init_hw and set to 1 after init_hw,
change it to 0.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
All ASICS we support has YCbCr support, so
the check is unnecessary, the currently logic
in validate output also returns true all
the time, so the unneccessary logic is removed
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently not supported, will black screen when set.
[How]
Fail validate timing helper for those modes.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Also add dram clock to clocks struct, for systems that uses them.
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Previously bandwidth validation was failing because swizzle mode was not
initialized during plane_state allocation. The swizzle mode was
calculated using pixed format which is how swizzle mode is initially
calculated in addrlib.
[How]
* Set default swizzle mode for validation to DC_SW_UNKNOWN
* Created new function in dcn10_assign_swizzle_mode which sets the
plane swizzle mode based on selected pixed format
* Added the call of assign_swizzle_mode into dc_validate_global_state
* Set failsafe swizzle mode back to DC_SW_LINEAR
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HDMI_scramber is not enabled for pixel rate >340Mhz.
[How]
Calculate the phy clock to include the Hw frame packing factor.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Sometimes there are indications that the incorrect driver is being
loaded in automated tests. This change adds the ability for builds to
be tagged with a string, and picked up by the test infrastructure.
[how]
dc.c will allocate const for build id, which is init-ed with default
value, indicating production build. For test builds, build server will
find/replace this value. The test machine will then verify this value.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
-----BEGIN PGP SIGNATURE-----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=dMl4
-----END PGP SIGNATURE-----
BackMerge v4.19-rc6 into drm-next
I have some pulls based on rc6, and I prefer to have an explicit backmerge.
Signed-off-by: Dave Airlie <airlied@redhat.com>
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DISPCLK value was previously requested to be 15% higher for all
ASICs that went through the dce110 bandwidth code path. As part of a
refactoring of dce_clocks and the dce110 set bandwidth codepath this
was removed for power saving considerations.
That change caused display corruption under certain hardware
configurations with Vega10.
[How]
The 15% DISPCLK increase is brought back but only on dce110 for now.
This is should be a temporary workaround until the root cause is sorted
out for why this occurs on Vega (or other ASICs, if reported).
Tested-by: Nick Sarnie <sarnex@gentoo.org>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Previously night light forced a full update by
applying a transfer function update regardless of if it was changed.
This logic was removed,
Now gamma surface updates are only applied when there is also a plane
info update, this does not work in cases such as using the night light
slider.
[HOW]
When moving the night light slider we will perform a full update if
the gamma has changed and there is a surface, even when the surface
has not changed. Also get stream updates in setgamma prior to
update planes and stream.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There are two different variables used to calculate v_update and v_ready,
one for validation and the other for performance parameter calculation.
Before the variable for validation was used which caused underflow on
1080edp with vsr enabled
[HOW]
program v_update and v_ready with the variables for performance parameter
calculation
Signed-off-by: Su Sung Chung <su.chung@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use link->link_index as index to pipe_ctx[] to get proper link
information instead of using index 0 to avoid potential miss matches.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
FPGA doesn't program backend, so we don't need certain link settings
(audio stream for example).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
current dc_link_detect function is not only detection but also update some link data.
[How]
added a pure get HPD state function.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
support i2c transition event log
[How]
refined aux REQ and REP events in aux flow.
commented REQ and REP events in i2c flow.
note: i2c event log is currently commented out. more work is required
to find an portocol parser to and generate event for the parser
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clock sources currently have support for asic specific
function pointers. But actual separation into functions
was never performed, leaving us with giant functions that
rely on switch.
This change creates separate functions, removing switch use.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We were not providing the correct pixel clocks to DML for marks
calculation.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add Raven2 definitions in the dc code
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Existing debug dump are all invariant, new “low 32-bit of address”
dump is not invariant
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are same purpose transition events.
[How]
remove the redundant event log.
Signed-off-by: Chiawen Huang <chiawen.huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Virtual sink is used when set mode happens on a disconnected display
to allow the mode set to proceed. This did not work with MST because
the logic for acquiring stream encoder uses stream signal to determine
the special handling is required, and stream signal is virtual instead
of DP in this case.
[How]
Use link type to decide instead.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The i2c and aux engines are similar, and should be placed
next to eachother for readability
[How]
Reorder the elements of the resource_pool struct
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
AMD Stoney reference board, there are only 2 pipes (not include
underlay), and 3 connectors. resource creation, only
2 I2C/AUX engines are created. Within dc_link_aux_transfer, when
pin_data_en =2, refer to enengines[ddc_pin->pin_data->en] = NULL.
NULL point is referred later causing system crash.
[how]
each asic design has fixed number of ddc engines at hw side.
for each ddc engine, create its i2x/aux engine at sw side.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some display need disconnect delay. Adding this parameter for future use
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Although 4 unique register values exist for gamma modes, two are
actually the same (the two RAMs) It’s not possible for caller to
understand this HW specific behavior, so some parsing is necessary
in driver
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]Update Code to get DTN golden log check to pass for tests run after
DAL217 tests.
[How]Change how dcn10_log_hw_state function prints HW state info
(CM_GAMUT_REMAP_Cx_Cx registers) when GAMUT REMAP is in bypass mode.
Signed-off-by: Gary Kattan <gary.kattan@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The dce_i2c_hw code contained four funtcions that were only
called in one place and did not have a clearly delineated
purpose.
[How]
Inline these functions, keeping the same functionality.
This is not a functional change.
The functions disable_i2c_hw_engine and release_engine_dce_hw were
pulled into their respective callers.
The most interesting part of this change is the acquire functions.
dce_i2c_hw_engine_acquire_engine was pulled into
dce_i2c_engine_acquire_hw, and dce_i2c_engine_acquire_hw was pulled
into acquire_i2c_hw_engine.
Some notes to show that this change is not functional:
-Failure conditions in any function resulted in a cascade of calls that
ended in a 'return NULL'.
Those are replaced with a direct 'return NULL'.
-The variable result is the one from dce_i2c_hw_engine_acquire_engine.
The boolean result used as part of return logic was removed.
-As the second half of dce_i2c_hw_engine_acquire_engine is only executed
if that function is returning true and therefore exiting the do-while
loop in dce_i2c_engine_acquire_hw, those lines were moved outside
of the loop.
Signed-off-by: David Francis <David.Francis@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
On PCO and up, whenever SMU receive message to indicate active
display count = 0. SMU will turn off 48MHZ TMDP reference clock
by writing to 1 TMDP_48M_Refclk_Driver_PWDN. Once this clock is
off, no PHY register will respond to register access. This means
our current sequence of notifying display count along with requesting
clock will cause driver to hang when accessing PHY registers after
displays count goes to 0.
[How]
Separate the PPSMC_MSG_SetDisplayCount message from the SMU messages
that request clocks, have display own sequencing of this message so
that we can send it at the appropriate time.
Do not redundantly power off HW when entering S3, S4, since display
should already be called to disable all streams. And ASIC soon be
powered down.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The i2c code contains two structs that contain the same
information as i2c_payload
[How]
Replace references to those structs with references to
i2c_payload
dce_i2c_transaction_request->status was written to but never read,
so all references to it are removed
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Logging hardware state can be done by triggering a write to the
debugfs file. It would also be useful to be able to read the hardware
state from the debugfs file to be able to generate a clean log without
timestamps.
[How]
Usage: cat /sys/kernel/debug/dri/0/amdgpu_dm_dtn_log
Threading is an obvious concern when dealing with multiple debugfs
operations and blocking on global state in dm or dc seems unfavorable.
Adding an extra parameter for the debugfs log context state is the
implementation done here. Existing code that made use of DTN_INFO
and its associated macros needed to be refactored to support this.
We don't know the size of the log in advance so it reallocates the
log string dynamically. Once the log has been generated it's copied
into the user supplied buffer for the debugfs. This allows for seeking
support but it's worth nothing that unlike triggering output via
dmesg the hardware state might change in-between reads if your buffer
size is too small.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Jordan Lazare <Jordan.Lazare@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is currently an intermittent hang from a memory leak in
DTN stress testing. It is caused by unfreed memory during driver
disable.
[How]
Do a dc_sink_release in the case that skips it incorrectly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Now that we "scale" time delays correctly on Maximus (as of diags svn
r170115), the forced "35 ms" wait time now becomes 35 ms * 500 = 17.5
seconds, which is far too long. Even having to repeat polling a
register once causes excessive delays on Maximus.
[How]
Just use the regular wait time passed to the generic_reg_wait()
function. This is sufficient for Maximus now, and it also means that
there's one less "Maximus-only" code path in DAL.
Also disable the "REG_WAIT taking a while:" message on Maximus, since
things do take a while longer there and 1-2ms delays are not uncommon
(and nothing to worry about).
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The function pointers of the dce_i2c_hw struct were never
accessed from outside dce_i2c_hw.c and had only one version.
As function pointers take up space and make debugging difficult,
and they are not needed in this case, they should be removed.
[How]
Remove the dce_i2c_hw_funcs struct and make static all
functions that were previously a part of it. Reorder
the functions in dce_i2c_hw.c.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is currently an intermittent hang from a memory leak in
DTN stress testing. It is caused by unfreed memory during driver
disable.
[How]
Do a dc_sink_release in the case that skips it incorrectly.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds support for LVDS displays.
v2: add support for spread spectrum, sink detect
v3: clean up enable_lvds_output
v4: fix up link_detect
v5: remove assert on 888 format
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105880
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The if statement isn't indented and it makes static checkers complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix comile warning like,
CC [M] drivers/gpu/drm/i915/gvt/execlist.o
CC [M] drivers/gpu/drm/nouveau/nvkm/subdev/instmem/nv50.o
CC [M] drivers/gpu/drm/radeon/btc_dpm.o
CC [M] drivers/isdn/hisax/avm_a1p.o
CC [M] drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_dpp.o
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c: In function ‘dcn10_update_mpcc’:
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:1903:9: warning: missing braces around initializer [-Wmissing-braces]
struct mpcc_blnd_cfg blnd_cfg = {0};
^
drivers/gpu/drm/amd/amdgpu/../display/dc/dcn10/dcn10_hw_sequencer.c:1903:9: warning: (near initialization for ‘blnd_cfg.black_color’) [-Wmissing-braces]
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Jiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Existing DTN infrastructure in driver is hacky. It uses implicit log
names, and also incorrect escape ID.
[how]
- Implement using generic DTN escape ID.
- Move file logging functionality from driver to to script; driver now outputs to string/buffer
- Move HWSS debug functionality to separate c file
- Add debug functionalty for per-block logging as CSV
- Add pretty print in python
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S3 stress test it is possible to resume from S4 without
calling mode set on eDP, meaning high level optimization flag is not
reset. If this is followed by an S3 resume call, driver will see
optimization flag is set and consume it and think backend is powered
on when in fact it is not.
This results in PHY being off in sequence where
S4->Resume->S3->Resume->ApplyOpt->black screen.
[How]
Move optimization flag to stream instead of a DC flag.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are two versions of the hw function pointers: one for dce80
and one for all other versions. These paired functions are
nearly identical. dce80 and dce100 should not require
different i2c access functions.
[How]
Combine each pair of functions into a single function. Mostly
the new functions are based on the dce100 versions as those
versions are newer, support more features, and
were more maintained.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Define register for dcn10 for future changes
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add csc_transform struct to dc_stream_update, and program if set when
updating streams
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
I2C code did not match dc resource model and was generally
unpleasant
[How]
Move code into new svelte dce_i2c files, replacing various i2c
objects with two structs: dce_i2c_sw and dce_i2c_hw. Fully split
sw and hw code paths. Remove all redundant declarations. Use
address lists to distinguish between versions. Change dce80 code
to newer register access macros.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add gamut remap to dc_stream_update struct, and program if set when updating
streams.
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Recently we fixed HDR static meta using AFMT registers to be treated as
fast stream update.
Dynamic meta is still being treated as (full) surface update because it
touches HUBP and it travels with pipe data.
Here we change it to be (fast) stream update.
Note, originally we also wanted to redesign here a bit, but without OS
level support for true dynamic meta, it's left the same. We are simply
using HW that can do dynamic meta to send HDR static meta, I still prefer
keeping it in one static meta type then defining dynamic meta types to
hold the same info. Once we know how OS interfaces look like, we can
do proper design.
[How]
Move dyn meta update from update_hubp_dpp to commit_planes_do_stream_update
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Vesa DPMS tool sends different HDR meta in OS flips without changing output
parameters. We don't properly update HDR info frame:
- we label HDR meta update as fast update
- when updating HW info frame, we only do it if full update
[How]
It should still be fast update, so when doing HW infoframe update,
do it always no matter the update type.
Also, don't request passive flip for HDR meta update only without output
transfer function or color space changed.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alvin lee <alvin.lee3@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- program infoframe for Stereo
- program stereo flip control registers properly
v2: Add missing license headers
Signed-off-by: Alvin lee <alvin.lee3@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: SivapiriyanKumarasamy <sivapiriyan.kumarasamy@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This was missed when pushing public patch for 3e3a40b03847 (drm/amd/display:
Updated HDR Static Metadata to directly take info packet raw)
This is currently no problem yet since we're not doing HDR on Linux yet.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove dependency on internal sink map and instead
use existing stream and plane state
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Unsigned int is guaranteed to be >= 0, and read_channel_reply checks for
overflows. read_channel_reply also returns -1 on error, which is what
dc_link_aux_transfer is expected to return on error.
[How]
Remove the if-statement. Return result of read_channel_reply directly.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Mikita Lipski <Mikita.Lipski@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
mono formats are treated exactly the same as equivallent bpp
444 formats. Dml validation however lacks 444 8 bit format
while dml perf param calculation lacks mono format support
This change makes them equivallent as far as the enum is concerned
to avoid having to update dml
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows us to avoid any vbios bugs when initializing clocks
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There are outstanding bugs for PIP in Dal3:
-Crash when toggling PIP visibility
-Global Alpha is not working, Adjusting global alpha
doesn’t have an effect
-Cursor is not working with pip plane and pipe splits
-One flash occurs when cursor enters PIP plane from
top/bottom
-Crash when moving PIP plane off the screen
[How]
Resolve divide by 0 error
Implement global alpha
Program cursor on all pipes
Add dst rects' x and y offests into cursor position
Disable cursor when it is beyond bottom/top edge
Signed-off-by: Gloria Li <geling.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
There is currently a dependency on the order in which tests are executed.
This is because the non-relevant state info is being printed, which results
in the output based on the state from the previous test.
[how]
Print DPP DTN log only if the pipe is enabled.
In addition to the affected per-submission DTN golden logs, included in this
change is also DTN golden log update for pre-submission tests.
The other DTN golden logs affected by this change will be updated upon
nightly test run (which will generate the updated DTN logs).
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
We didn't transfer the camera/video viewport coordinate
when doing rotation and mirror.
[how]
To correct the viewport coordinate in calculate_viewport().
Signed-off-by: Martin Tsai <Martin.Tsai@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the hardware supports DFS bypass it will always be enabled after
creation of the DCCG. DFS bypass should only be enabled when
the current stream consists of a single embedded panel and the
minimum display clock is below the DFS bypass threshold.
[How]
Add a function to the DCCG table that updates the DFS bypass state
when setting the bandwidth. If the DFS bypass state is changed, the
clock needs to be reprogrammed to reflect this before the DPREFCLK
is updated for audio endpoints. The existing display clock value
is used as the target display clock value when reprogramming since the
resulting change will be equal or larger to the current value.
These changes only specifically target dce110 but do offer a framework
for support on other applicable targets.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: David Francis <David.Francis@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We explicitly disable DFS bypass support when creating DC. Support
for this feature should now be in place so it can be left implicitly
enabled.
[How]
Remove the line that disables DFS bypass support.
Note: This option was actually reset to false anyway for most of
the hardware I've tested on making this particular line misleading
in the first place. This patch also fixes this issue.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
While there is support for using and quering DFS bypass clocks the
hardware is never notified to enter DFS bypass mode for dce110.
[How]
Add a flag that can be set when programming the display engine PLL
to enable DFS bypass mode. If this flag is set then the hardware is
notified to enter DFS bypass mode and the correct display engine clock
frequency can be acquired.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Legacy IRI style is not linux friendly.
[how]
New function pointer call
semantics will be used for all future PPLIB/DAL interfaces, and also
some existing will be refactored. This change defines how the
new function pointer structures will look, as well as implements
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8624c3c4dbfe24fc6740687236a2e196f5f4bfb0.
We need CONFIG_DRM_AMD_DC_DCN1_0 to guard code that is using fp math.
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Dentist did ranges were incomplete as max setting has an unusual
divider step up of 66.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dp_ss_off flag doesn't need to be set, so we create a link_init
function if it is needed by an asic
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dp_ss_control = 0 means ss is off, we had a typo where
we would double not dp_ss_control while setting dp_ss_off
flag
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do not retrain link settings if lane count and link rate are both
unknown. Causes driver to be stuck reading VBIOS register after
removing emulated connection.
Signed-off-by: Samson Tam <Samson.Tam@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Older ASICs require both phys_id and connector_id
to execute bios command table. If we are not passing the
right connector_id - it can lead to a black screen.
[how]
Set connector_obj_id when executing vbios command table
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
We are disabling clock source while other pipes are still using
it, because we don't verify the number of pipes that share it.
[how]
- Adding a function in resources to return the number of pipes
sharing the clock source.
- Checking that no one is sharing the clock source before disabling
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why]
HDMI and DVI share the same PHY clock and single link
DVI and HDMI both use 4 lanes, so they should be allowed
to be sharing the same clock source if all other parameters
are satisfied.
[how]
Change a check for general DVI to Dual DVI.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DOUBLE_BUFFER_EN bit is getting cleared before enable blanking.
That leads to CRTC_BLANK_DATA_EN is getting updated immediately.
[How]
Get DOUBLE_BUFFER_EN bit set, the same as DCE110.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
for vega, dp set_panel_mode is
handled by psp firmware. dal should not program the
register again.
[how]
dal does not program panel mode.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When programming tonga's connector's backend we didn't take
in account that HDMI's colour depth might be more than 8bpc
therefore we need to add a switch statement that would adjust
the pixel clock accordingly.
[how]
Add a switch statement updating clock by its appropriate
coefficient.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
We seem to have an issue where high enough display clock
will not get set properly during S3 resume if we only
call vbios once
[How]
Expand condition of display clock programming to happen
even when cached display clock matches requested display
clock
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The pointer for integrated_info can be NULL which causes the system to
do a null pointer deference and hang on boot.
[How]
Add a check to ensure that integrated_info is not null before enabling
DP ss.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Prevent clock source sharing between HDMI and DP connectors.
DP shouldn't be sharing its ref clock with phy clock,
which caused an issue of older ASICS booting up with multiple
diplays plugged in.
[how]
Add an extra check that would prevent HDMI and DP sharing clk.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[why] dp hbr2 eye diagram pattern for raven asic is not stabled.
workaround is to use tp4 pattern. But this should not be
applied to asic before raven.
[how] add new bool varilable in asic caps. for raven asic,
use the workaround. for carrizo, vega, do not use workaround.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The calculated values for actual disp_clk_khz were ignored when
notifying pplib of the new display requirements. In order to honor DFS
bypass clocks from the hardware, the calculated value should be used.
[How]
The return value for set_dispclk is now assigned back into new_clocks
and correctly carried through into dccg->clks.phyclk_khz. When notifying
pplib of new display requirements dccg->clks.phyclk_khz is used
instead of dce.dispclk_khz. The value of dce.dispclk_khz was never
explicitly set to anything before.
A 15% higher display clock value than calculated is no longer requested
for dce110 since it now makes use of the calculated value.
Since dce112 makes use of dce110's set_bandwidth but not its
update_clocks it needs to have the value correctly carried through.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Custom degamma lut functions are a feature we would
like to support on compatible hardware
[How]
In atomic check, convert from array of drm_color_lut to
dc_transfer_func. On hardware commit, allow for possibility
of custom degamma. Both are based on the equivalent
regamma pipeline.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In the dce112 function to destroy the resource pool, engines
(the aux engines) is destroyed twice. This has no ill effects
but is a tad redundant.
[How]
Remove the redundant call
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This hook that is supposed to read the actual backlight value
is used in a few places throughout the kernel to setup or force
update on backlight
[How]
Create a dc function that calls the existing abm function, and
call that function from amdgpu
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
400.1.1 is failing because we are not performing link training when
we get an HPD pulse for the same display. This is breaking DP
compliance
[How]
Always perform link training after HPD pulse if the detection
reason is not DETECT_REASON_HPDRX.
Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VGA sometimes has trouble retrieving the EDID on very long cables, KVM
switches, or old displays.
[How]
Only require EDID read for HDMI and DVI and exempt other types (DP,
VGA). We currently don't support VGA but if anyone adds support in the
future this might get overlooked.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Suggested-by: Michel Dänzer <michel@daenzer.net>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some boards seem to have a problem where HPD is high on HDMI even though
no display is connected. We don't want to report these as connected. DP
spec still requires us to report DP displays as connected when HPD is
high but we can't read the EDID in order to go to fail-safe mode.
[How]
If connector_signal is not DP abort detection if we can't retrieve the
EDID.
v2: Add Bugzilla and stable
Bugzilla: https://bugs.freedesktop.org/107390
Bugzilla: https://bugs.freedesktop.org/106846
Cc: stable@vger.kernel.org
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a missing void parameter to function dc_create_transfer_func, fixes
sparse warning:
warning: non-ANSI function declaration of function 'dc_create_transfer_func'
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR_SET command is sent to the microcontroller in order to initialize
parameters needed for PSR feature, such as telling the microcontroller
which pipe is driving the PSR supported panel. When this command is
skipped or fails, the microcontroller may program the wrong thing if
driver tries to enable PSR.
[How]
If PSR_SET fails, do not set psr_enable flag to indicate the feature is
not yet initialized.
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The sequence is slightly changed when bring .set_bandwidth out
from the end of programming backend to the end of programming
surface. Vega10 doesn't like to get clocks updated if
stream_count is zero in the current context (Atomic Reset).
[How]
Do not update clocks if no stream is showing up in the context.
Fixes 1b2b130192 "dc: Remove 300Mhz minimum disp clk limit."
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
engine and aux_engine are unnecessary layers we want to remove this
layer.
[How]
flatten engine and aux engine structs into one struct called
aux_engine and remove all references to the engine struct.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some receivers seem to fail the first link training but are good on
subsequent tries. We want to retry link training again. This fixes
HTC vive pro not lighting up after being disabled.
[How]
Check if the link training passed without fall back if this is not
the case then we retry link training.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
confusing as to which part of debug is informational, and which part causes behavioral change
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Aux engine is created from i2caux layer. We want to remove this layer
and use the engine directly.
[How]
Decouple aux engine from i2caux. Move aux engine related code to dce folder and use
dc resource pool to manage the engine. And use the engine functions directly
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Diags has POR to run the video workload using AYCRCB8888 through DCN;
capture it through DWB and send it to VCN hardware to encode
[how]
added the code to support this format so that DPP ICSC will be able to
convert it from YUV444 to internal RGB and DWB OCSC will be able to
convert from internal RGB to YUV420
Signed-off-by: vikrant mhaske <vikrant.mhaske@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When a dce100 asic was suspended, the clocks were not set to 0.
Upon resume, the new clock was compared to the existing clock,
they were found to be the same, and so the clock was not set.
This resulted in a pernicious blackscreen.
[How]
In atomic commit, check to see if there are any active pipes.
If no, set clocks to 0
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
diag specify what the full config and is only concerned about pass/fail at the end
having inter-op code like verifiying we can actually train at reported link rate
slows down diag test and add complexity we don't need
[how]
add dc_debug option to skip capability link trianing
also remove hbr in function name as verify is not specific to hbr
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Ken Chalmers <ken.chalmers@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The warning message floods the dmesg log on Tonga even
though it is expected to have a pix_clk set to zero,
when the pipe is not active.
[how]
remove the assert
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Allowing CONFIG_DRM_AMD_DC_DCN1_0 to be disabled on X86 was an
opportunity for display with Raven Ridge accidentally not working.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Any Linux kernel code should pass checkpatch.pl with no errors and
little, if any, warning.
[How]
Fixing some spacing errors and warnings.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Cursor boosting can only be done on DCN+
Check for nullptr since DCE doesn't implement it.
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Sivapiriyan Kumarasamy <Sivapiriyan.Kumarasamy@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Steven Chiu <Steven.Chiu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some DTN tests still failing @ 2% Need to reduce.
[how]
add instrumentation code to driver so we can get more information from failed runs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We sometime require remapping of FB address space to UMA
[How]
Move address tracking up a layer before we apply address translation
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows DM to do any necessary updates before MST discovery starts.
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Testing team wants a way to tell if HDR is on or not
[How]
Program the overscan color to visually indicate the HDR state of the top-most plane
Signed-off-by: Gloria Li <geling.li@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Cursor boosting is done via CNVC_CUR register which is DPP, not HUBP
Previous commit was implementing it in HUBP functions,
and also breaking diags tests.
[How]
1. Undo original commit as well as Eric's diags test fix, almost completely
2. Move programming to DPP and call via new dc_stream function
3. Also removing cur_rom_en from dpp_cursor_attributes and programming
as part of normal cursor attributes as it depends on cursor color format
Signed-off-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently we do not turn off autocal when scaling is in bypass.
In case vbios enalbes auto scale and our first mode set is a non-scaled
mode we have autocal on causing screen corruption.
[how]
moves turning autocal off to be first thing done during scaler setup
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why] Prevent unexpected color shows if DalMpVisualConfirm enable.
[How] Zero out color configuration data for DalMpVisualConfirm when initiating.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DV updated their dml with an option to use max vstartup,
this updates dc dml with the same option
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The previous code could allow through attempts to enable more streams
than there are timing generators, in designs where the number of pipes
is greater than the number of timing generators.
[How]
Compare the new stream count to the resource pool's timing generator
count, instead of its pipe count. Also correct a typo in the error
message.
Signed-off-by: Ken Chalmers <ken.chalmers@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Regamma/CTM tests require CRC support
[How]
The CRC registers that were used in DCE exist under different
names in DCN. The code was copied from DCE (in
dc/dce110/dce110_timing_generator.c) into DCN, and changed to
use the DCN register access helper functions.
Signed-off-by: David Francis <David.Francis@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
PNP cause bsod regression fix
[HOW]
Add NULL check
Signed-off-by: Yue Hin Lau <Yuehin.Lau@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
"DalEnableHDMI20" set to 0, disallow HDMI YCbCr420 and pixel clock > 340Mhz
Default is enabled.
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
get_channel_status() can return 0 in returned_bytes, and report a
successful operation result. This is because it prunes the first status
byte out. This was preventing read_channel_reply() from being called
(due to the faulty condition), and consequently preventing the AUX
reply status from being set.
[How]
Fix the conditional so that it accounts for when get_channel_status()
returns 0 bytes read.
[Fixes]
Fixes possible edid read failures during S3 resume, where we are now
relying on DRM's DP AUX handling. This was an regression introduced by:
Author: Harry Wentland <harry.wentland@amd.com>
drm/amd/display: Return aux replies directly to DRM
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is no point in keeping the AUX reply value in the raw format as
returned from reading the AUX_SW_DATA register.
[How]
Shift it within read_channel_reply(), where the register is read, before
returning it.
Signed-off-by: Leo (Sunpeng) Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Duke Du <Duke.Du@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
In eDP spec, the min duration in LCDVDD on-off-on sequence should be
500ms, some BOE panels need 700ms to pass.
[HOW]
Add patch to wait more time when eDP power on.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- define new dpcd address in drm
- implement new members in dpcd_caps to store values read from new dpcd address
Signed-off-by: Alvin lee <alvin.lee3@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Removed dal/dm/dc loggers from linux, switched to kernel prints
- Modified functions that used these directly to use macros
- dc_logger support is completely dropped from Linux
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently we still go through DC code that does error checking, retries,
etc. There's no need for that since DRM already does that for us. This
simplifies the code a bit and makes it easier to debug.
This also ensures we correctly tell DRM how many bytes have actually
been read, as we should. This allows DRM to correctly read the EDID on
the Chamelium DP port.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DRM's DP helpers take care of dealing with the error code for us. In
order not to step on each other's toes we'll need to be able to simply
read auch channel replies without further logic based on return values.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Access to GPIO needs to be serialized. Aux transactions are already
serialized in DRM but we also need to serialize access to the GPIO pin
for purposes of DP dongle detection.
Call is_dp_sink_present through DM so we can lock correctly. This
follows the same pattern used for DPCD transactions.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
in case we have very few pins in the table, check fails and we can't boot
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
add generic indirect register access following our register access pattern
this will make it easier to review code and programming sequence,
with all the complexity hidden in macro
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
we were using 6 instances based on i2caux_dce110.c
[HOW]
pass in how many instances to ctor
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
expose dc function to be called by linux dm
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Megachip dockings accesses ddc line through display driver when
installing FW. Previously, we would fail every transaction because
link attached to mst branch did not have their ddc transaction type
set.
[How]
Set ddc transaction type when mst branch is connected.
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Separate HUBP surface size and rotation/mirror programming so that
HUBP revision without mirror/rotation do not access those register
fields.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit cc19514113.
This commit was problematic on other OSes. The real solution is to
leave all the error checking to DRM and don't do it in DC, which is
addressed by "Return aux replies directly to DRM" later in this patchset.
v2: Add reason for revert.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 8a61bc085f.
Need to revert "make dm_dp_aux_transfer return payload bytes instead of
size", which this commit is based on. That commit was problematic on
other OSes. The real solution is to leave all the error checking to DRM
and don't do it in DC, which is addressed by "Return aux replies
directly to DRM" later in this patchset.
v2: Add reason for revert.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
const to avoid hard-to-find bugs where some function overrides a
function pointer.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It is good practice to make global function tables const to avoid
accidental override.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise we try to program hardware with the wrong watermark functions
when multiple DCE generations are installed in one system.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add suffix ULL to constant 5 and cast variables target_pix_clk_khz and
feedback_divider to uint64_t in order to avoid multiple potential integer
overflows and give the compiler complete information about the proper
arithmetic to use.
Notice that such constant and variables are used in contexts that
expect expressions of type uint64_t (64 bits, unsigned). The current
casts to uint64_t effectively apply to each expression as a whole,
but they do not prevent them from being evaluated using 32-bit
arithmetic instead of 64-bit arithmetic.
Also, once the expressions are properly evaluated using 64-bit
arithmentic, there is no need for the parentheses that enclose
them.
Addresses-Coverity-ID: 1460245 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1460286 ("Unintentional integer overflow")
Addresses-Coverity-ID: 1460401 ("Unintentional integer overflow")
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That change was a merge gone bad.
This reverts commit cb1d7eacb5.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The ->info[] array has DAL_IRQ_SOURCES_NUMBER elements so this condition
should be >= instead of > or we could read one element beyond the end of
the array.
Fixes: 4562236b3b ("drm/amd/dc: Add dc display driver (v2)")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The wrong enum type is used to initialize the result, leading to a
warning when using clang:
drivers/gpu/drm/amd/amdgpu/../display/dc/core/dc_link_dp.c:1998:26: warning:
implicit conversion from enumeration type 'enum ddc_result' to different
enumeration type 'enum dc_status' [-Wenum-conversion]
enum dc_status result = DDC_RESULT_UNKNOWN;
~~~~~~ ^~~~~~~~~~~~~~~~~~
1 warning generated.
Initialization of result is unnecessary anyway, just drop the
initialization.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
use worse case watermark (consider both DCC and VM)
to keep golden consistent regardless of DCC
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In case of roation, width and height in viewport is difference
between viewport and h_active and v_active, while this is not scaling.
The right way is check ratios in scaling data,
to determine it is a scaling case or not.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently dcn1 will not switch between watermark sets so we can
save time by not calculating 3 extra sets.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Set the powerplay debug flag to false for both Windows and Linux
to allow the calls to pplib. So we can retrieve the clock values
from powerplay instead of using default hardcoded values.
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Fixing integer overflow bug in wait_for_fbc_state_changed()
- Correct the max value of retries for the corresponding warning
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Tony Cheng <tony.cheng@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
