Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Use binman to build an image which includes all the U-Boot phases so that
a full VBE boot can take place with just that image.bin file. Attach the
image file to mmc2 so it can be loaded.
VBE is used to load images in two phases:
- In VPL, VBE decides which SPL image to load
- In SPL, VBE decides which U-Boot image to load
The latter should really be determined by VPL, since it does the full
signature verification on the selected configuration. However, we have
separate configurations for SPL and U-Boot proper, so for now we keep it
simple and have SPL do its own verification. This will need to be
tidied up later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we put the driver in the /chosen node in U-Boot. This is a bit
strange, since U-Boot doesn't normally use that node itself. It is better
to put it under the bootstd node.
To make this work we need to copy create the node under /chosen when
fixing up the device tree. Copy over all the properties so that fwupd
knows what to do.
Update the sandbox device tree accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox runs the next phase from discrete executables, so for
example u-boot-tpl runs u-boot-vpl to get to the next phase.
In some cases the phases are all built into a single firmware image, as is
done for real boards. Add support for this to sandbox.
Make it higher priority so that it takes precedence over the existing
method.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the sandbox executable is assumed to be arg[0] but this only
works for a single jump (e.g. from SPL to U-Boot). Add a new arg to solve
this issue, along with a detailed comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports jumping to a file, to get to the next
U-Boot phase. We want to support other methods, so update the code to
use an enum for the method. Also use the
Use board_boot_order() to set the order, so we can add more options.
Also add the MMC methods into the BOOT_DEVICE enum so that booting
from MMC can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
This happens every time sandbox moves to the next phase so is not very
interesting. Display the message only when debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At present we normally write tests either in Python or in C. But most
Python tests end up doing a lot of checks which would be better done in C.
Checks done in C are orders of magnitude faster and it is possible to get
full access to U-Boot's internal workings, rather than just relying on
the command line.
The model is to have a Python test set up some things and then use C code
(in a unit test) to check that they were done correctly. But we don't want
those checks to happen as part of normal test running, since each C unit
tests is dependent on the associate Python tests, so cannot run without
it.
To acheive this, add a new UT_TESTF_MANUAL flag to use with the C 'check'
tests, so that they can be skipped by default when the 'ut' command is
used. Require that tests have a name ending with '_norun', so that pytest
knows to skip them.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
As STI timer is renamed to ARM A9 global timer, change BCM63138 to use
the new global timer config symbol name.
This patch applies on top of the my previous patch [1].
[1]: https://lists.denx.de/pipermail/u-boot/2022-August/491060.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCY17nfA4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXPPoAJ0UYyt3kwslUlAJhOC+KU9UlYnVuwCbBXIQyBua
K5clq+GyxXfaDl2Hnvc=
=XXVp
-----END PGP SIGNATURE-----
Merge tag 'video-20221030' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix [hv]sync active vs back porch in dw_mipi_dsi
- simplefb rotation support
- support splash as raw image from MMC
- enhancements to Truetype console (multiple fonts and sizes)
- drop old LCD support
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently sandbox configuration defautls to 64bit and there is no
automation for building 32bit sandbox on 32bit hosts.
Use _LP64 macro as heuristic for detecting 64bit targets.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The jmp_buf type is required by the C99 specification.
Defining it for x86 fixes building the longjmp unit test.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If longjmp(jmp_buf env, int val) is called with val = 0, the setjmp()
macro must return 1.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- nuvoton: add expire function for generic reset (Jim)
- handle watchdogs during keyed autoboot (Rasmus)
- cyclic: Don't disable cylic function upon exceeding CPU time (Stefan)
- ulp wdog: Updates to support iMX93 and DM (Alice)
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
