This TODO can now be removed and replaced by the previous patch
"drm/msm/mdp5: Update headers (add CTL flush bits)"
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some upcoming targets have more bits to set in CTL_FLUSH
registers.
Example: msm8x16 needs to set TIMING1 bit so that some of the
INTF1's interface registers get flushed.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the hw configuration for msm8x16 chipsets in
mdp5_cfg module.
Note that only one external display interface is present in this
configuration (DSI) but has not been enabled yet. It will be enabled
once drm/msm driver supports DSI connectors.
v2: add CTL flush register's hardware mask [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
SMP blocks are configured for specific client IDs (ports).
These client IDs can be different from one chip to another for a
given pipe.
e.g.: DMA0 pipe fetch Y component is connected to:
- port #10 for MDP5 v1.3
- port #4 for MDP5 v1.6
In order to be compatible for upcoming versions of MDP5, the
client ID list is passed through the MDP5 config module rather
than using a list of hard-coded enum values.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch contains the generated header file of the following
change "drm/msm/mdp5: Get SMP client list from mdp5_cfg".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP block is actually contained inside the MDSS block. For some
chipsets, the base address of the MDP registers is different from the
current (assumed) 0x100 offset.
Like CTL and LM blocks, this changes introduce a dynamic offset
for the MDP instance, which can be found out at runtime, once the
MDSS HW version is read.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change contains the generated header file for the following
change "drm/msm/mdp5: Separate MDP5 domain from MDSS domain".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The width and height in SSPP_SRC_IMG_SIZE register should be the
size of the entire source framebuffer, not the fetch size.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the registers in mdp5 ping pong blocks
and split display control registers.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pingpong register base addresses are different across platforms.
This change adds this information to config table and initialize
the values for 8x74 and 8084.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Up until now, we assume that eDP is tight to intf_0 and HDMI to
intf_3. This information shall actually come from the mdp5_cfg
module since it can change from one chip to another.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
v3: add sanity check before writing in INTF_TIMING_ENGINE_EN registers
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some interfaces (WB, DSI Command Mode) need to be kicked off
through a START Signal. This signal needs to be sent at the right
time and requests in some cases to keep track of the pipeline
status (eg: whether pipeline registers are flushed AND output WB
buffers are ready, in case of WB interface).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
DSI and WB interfaces need a more complex pipeline configuration
than the current mdp5_ctl_set_intf().
For example, memory output connections need to be selected for
WB. Interface mode (Video vs. Command modes) also need to be
configured for DSI.
This change takes care of configuring the whole pipeline as far
as operation mode goes. DSI and WB interfaces will be added
later.
v2: rename macro to mdp5_cfg_intf_is_virtual() [pointed by Archit]
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Remove temp bisectability hack -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Prepare for pipeline operation mode configuration, in particular
for DSI and WB modes.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
[Throw in a #define temporarily to keep things bisectable -Rob]
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 hardware has some limitation and requires to avoid flushing
registers more than once between two Vblanks.
This change removes all FLUSH operations (except for HW cursor)
beside the one coming from a CRTC's ->atomic_flush().
This avoid this type of behavior (eg: CRTC + 1 plane overlay):
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_ctl_commit] flush (20040) CTL + LM0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
and replaces it by:
[drm:mdp5_crtc_vblank_irq] vblank
[drm:mdp5_ctl_commit] flush (20048) CTL + LM0 + RGB0
[drm:mdp5_crtc_vblank_irq] blank
[drm:mdp5_ctl_commit] flush (20049) CTL + LM0 + RGB0 + VIG0
[drm:mdp5_crtc_vblank_irq] blank
Only *one* FLUSH is called between Vblanks interrupts.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add support to use the VRAM carveout (if specified in dtb) for fbdev
scanout buffer. This allows drm/msm to take over a bootloader splash-
screen, and avoids corruption on screen that results if the kernel uses
memory that is still being scanned out for itself.
Signed-off-by: Rob Clark <robdclark@gmail.com>
We'll want to extend this a bit to handle also a reserved-memory
("stolen") region, so that drm/msm can take-over bootloader splash
screen. First split it out into it's own fxn to reduce noise in
the following patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJU/NacAAoJEHm+PkMAQRiGdUcIAJU5dHclwd9HRc7LX5iOwYN6
mN0aCsYjMD8Pjx2VcPCgJvkIoESQO5pkwYpFFWCwILup1bVEidqXfr8EPOdThzdh
kcaT0FwUvd19K+0jcKVNCX1RjKBtlUfUKONk6sS2x4RrYZpv0Ur8Gh+yXV8iMWtf
fAusNEYlxQJvEz5+NSKw86EZTr4VVcykKLNvj+/t/JrXEuue7IG8EyoAO/nLmNd2
V/TUKKttqpE6aUVBiBDmcMQl2SUVAfp5e+KJAHmizdDpSE80nU59UC1uyV8VCYdM
qwHXgttLhhKr8jBPOkvUxl4aSXW7S0QWO8TrMpNdEOeB3ZB8AKsiIuhe1JrK0ro=
=Xkue
-----END PGP SIGNATURE-----
Merge tag 'v4.0-rc3' into drm-next
Linux 4.0-rc3 backmerge to fix two i915 conflicts, and get
some mainline bug fixes needed for my testing box
Conflicts:
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/intel_display.c
Use cases like rotation require these hooks to have some context so they
know how to prepare and cleanup the frame buffer correctly.
For i915 specifically, object backing pages need to be mapped differently
for different rotation modes and the driver needs to know which mapping to
instantiate and which to tear down when transitioning between them.
v2: Made passed in states const. (Daniel Vetter)
[airlied: add mdp5 and atmel fixups]
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In kexec environment, we are more likely to encounter irq's already
enabled from previous environment. At which point we find that writes
to disable/clear pending irq's are slightly less than useless without
first enabling clocks.
TODO: full blown state read-in so kexec'd kernel can inherit the mode
already setup.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Seems like we just want BLEND_EN and not BLEND_TRANSP_EN (setting the
latter results in black pixels in the cursor image treated as
transparent).
Signed-off-by: Rob Clark <robdclark@gmail.com>
If cursor is set near the edge of the screen, it is not valid to use the
new cursor width/height as the ROI dimensions. Split out the ROI calc
and use it both cursor_set and cursor_move.
Signed-off-by: Rob Clark <robdclark@gmail.com>
If the atomic commit fails due to completion wait interruption the
atomic commit object is not freed and is thus leaked. Free it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
When a CRTC is disabled, no CTL is allocated to it (CRTC->ctl == NULL);
in that case we should not try to FLUSH registers and do nothing instead.
This can happen when we try to move a cursor but the CRTC's CTL
(CONTROL) has not been allocated yet (inactive CRTC).
It can also happens when we .atomic_check()/.atomic_flush() on a
disabled CRTC.
A CTL needs to be kept as long as the CRTC is alive. Releasing it
after the last VBlank is safer than in .atomic_flush().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Some target have up to 6 layer mixers (LM).
Let the header file access the last LM's base address.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Commit 0b776d457b ("drm/msm: fix fallout of atomic dpms
changes") has a typo in both mdp5_encoder_helper_funcs and
mdp5_crtc_helper_funcs definitions:
.dpms entry should be replaced by .disable and .enable
Also fixed a typo in mdp5_encoder_enable().
Note that these typos are only present for MDP5. MDP4 is fine.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
These names only make sense because of backwards compatability with
the order used by the crtc helper library. There's not really any real
requirement in the ordering here.
So rename them to something more descriptive and update the kerneldoc
a bit. Motivated in a discussion with Laurent about how to restore
plane state for dpms for drivers with runtime pm.
v2: Squash in fixup from Stephen Rothwell to fix a conflict with
tegra.
Cc: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Useful to avoid recompiling to disable fbdev. Useful because otherwise
the first modeset happens under console_lock (ie. debugging sadness).
Signed-off-by: Rob Clark <robdclark@gmail.com>
Combining -Werror with all the extra warning flags that W=1 adds doesn't
go so well. Especially because some of the warnings triggered are from
included headers. So just drop -Werror.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In case we request a number of SMP blocks which is lower than
the already reserved blocks, we should not try to allocate a
negative number, but 0 blocks instead.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
So after clarification from qcom, it seems mdp4 and mdp5 support
*de*interlacing but not generating an interlaced signal. Which would
explain why interlaced modes never worked properly.
So disable in the one connector which was claiming to support
interlaced.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The gnome-shell wayland compositor triggers a setcrtc with an fb that is
still being rendered, triggering the call to _wait_fence_interruptable().
But a NULL timeout means "don't wait, return -EBUSY if not ready", which
in turn causes the setcrtc to fail.
Signed-off-by: Rob Clark <robdclark@gmail.com>
This patch implements the hardware accelarated cursor
support for MDP5 platforms.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Wentao Xu <wentaox@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
In the same idea mdp5_cfg was added, this change allows us to quickly
add new instances, such as apq8084's HDMI in this case.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change add the regulator/clock configuration for MDP5 v1.3.
This config is close to the one already existing for 8x74, except
that one more regulator is needed (hpd-5v-en).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Instead of reporting BUG_ON when resources arrays are not
dimensioned correctly, this patch does a dynamic allocation of
these arrays. This is needed for the following patches that add a
regulator for a new target.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
mdp5_ctl_set_intf()'s second argument should be "int", not "enum mdp5_intf".
The passed in value is "intf", not "intf_id".
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Modified the hard-coded hdmi connector/encoder implementations in msm drm
driver to support both edp and hdmi.
V1: Initial change
V2: Address Thierry's change
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds a new eDP connector in msm drm driver. With this
change, eDP panel can work with msm platform under drm framework.
v1: Initial change
v2: Address Rob's comments
Use generated header file for register definitions
Change to devm_* APIs
v3: Address Thierry's comments and rebase on top of atomic changes
Remove edp_bridge_mode_fixup
Remove backlight control code and rely on pwm-backlight
Remove continuous splash screen support for now
Change to gpiod_* APIs
v4: Fix kbuild test issue
Signed-off-by: Hai Li <hali@codeaurora.org>
[robclark: v5: rebase on drm_bridge changes in drm-next]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The patch add support for YUV frame format
for MDP4 platform.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change adds the NV12 format support for public planes.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Both MDP4 and MDP5 share some code as far as YUV support is
concerned. This change adds this information and will be followed
by the actual MDP4 and MDP5 YUV support patches.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Resync from rnndb database, to pull in register defines for:
* eDP
* HDMI/HDCP
* mdp4/mdp5 YUV support
* mdp5 hw cursor support
Signed-off-by: Rob Clark <robdclark@gmail.com>
On !SMP systems spinlocks do not exist. Thus checking of they
are active will always fail.
Use
assert_spin_locked(lock);
instead of
BUG_ON(!spin_is_locked(lock));
to not BUG() on all UP systems.
Signed-off-by: Bruno Prémont <bonbons@linux-vserver.org>
[robclark: drop stray ')']
Signed-off-by: Rob Clark <robdclark@gmail.com>
3d3f8b1f8b ("drm/bridge: make bridge registration independent of drm
flow") resulted that the hdmi bridge object would be leaked at teardown.
Just switch over to devm_kzalloc() as the easy way to solve this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
As a result of atomic DPMS support, the various prepare/commit hooks get
called in a way that msm dislikes. We were expecting prepare/commit to
bracket a modeset, which is no longer the case. This was needed to hold
various extra clk's (such as interface clks) on while we are touching
registers, and in the case of mdp4 holding vblank enabled.
The most straightforward way to deal with this, since we already have
our own atomic_commit(), is to just handle prepare/commit internally to
the driver (with some additional vfuncs for mdp4 vs mdp5), and switch
everything over to instead use the new enable/disable hooks. It doesn't
really change too much, despite the code motion. What used to be in the
encoder/crtc dpms() fxns is split out into enable/disable.
We should be able to drop our own enable-state tracking, as the atomic
helpers should do this for us. But keeping that for the short term for
extra debugging as atomic stablizes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Only the legacy helpers use these entry points. Don't populate them
with transitional helpers, since that just makes things more confusing.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[robclark: reword commit msg]
Signed-off-by: Rob Clark <robdclark@gmail.com>
The msm gpu drivers depend on both the DT mechanism and the
common clk handling code, if they are not enabled, we get
a number of build errors:
In file included from drivers/gpu/drm/msm/hdmi/hdmi.h:27:0,
from drivers/gpu/drm/msm/hdmi/hdmi_bridge.c:18:
drivers/gpu/drm/msm/msm_drv.h:45:24: fatal error: mach/board.h: No such file or directory
#include <mach/board.h>
^
drivers/gpu/drm/msm/hdmi/hdmi_phy_8960.c:503:2: error: implicit declaration of function 'devm_clk_register' [-Werror=implicit-function-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Currently, third party bridge drivers(ptn3460) are dependent
on the corresponding encoder driver init, since bridge driver
needs a drm_device pointer to finish drm initializations.
The encoder driver passes the drm_device pointer to the
bridge driver. Because of this dependency, third party drivers
like ptn3460 doesn't adhere to the driver model.
In this patch, we reframe the bridge registration framework
so that bridge initialization is split into 2 steps, and
bridge registration happens independent of drm flow:
--Step 1: gather all the bridge settings independent of drm and
add the bridge onto a global list of bridges.
--Step 2: when the encoder driver is probed, call drm_bridge_attach
for the corresponding bridge so that the bridge receives
drm_device pointer and continues with connector and other
drm initializations.
The old set of bridge helpers are removed, and a set of new helpers
are added to accomplish the 2 step initialization.
The bridge devices register themselves onto global list of bridges
when they get probed by calling "drm_bridge_add".
The parent encoder driver waits till the bridge is available
in the lookup table(by calling "of_drm_find_bridge") and then
continues with its initialization.
The encoder driver should also call "drm_bridge_attach" to pass
on the drm_device to the bridge object.
drm_bridge_attach inturn calls "bridge->funcs->attach" so that
bridge can continue with drm related initializations.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Assign the pointer to bridge ops structure(drm_bridge_funcs) in
the bridge driver itself, instead of passing it to drm_bridge_init.
This will allow bridge driver developer to pack bridge private
information inside the bridge object and pass only the drm-relevant
information to drm_bridge_init.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Make drm_fb_helper_initial_config() return an int rather than a bool so
that the error can be properly propagated. While at it, update drivers
to propagate errors further rather than just ignore them.
v2:
- cirrus: No cleanup is required, the top-level cirrus_driver_load()
will do it as part of cirrus_driver_unload() in its cleanup path.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
[danvet: Squash in simplification patch from kbuild.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Next batch of atomic work. Most important is the propertification from Rob
and the nth iteration of the actual atomic ioctl originally from Ville.
Big differences compared to earlier revisions:
- Core properties are now fully handled by the core, drivers can only
handle driver-specific properties.
- Atomic props&ioctl are opt-in per file_priv, userspace needs to
explicitly ask for it (like universal plane support).
- For now all hidden behind the atomic module option until this has
settled a bit.
- Atomic modesets are currently not possible since the exact abi for how
to handle the mode property is still under discussion.
Besides this some cleanup patches from me and the addition of per-object
state to global state backpointers to simplify drivers.
* tag 'topic/atomic-core-2015-01-05' of git://anongit.freedesktop.org/drm-intel:
drm: Ensure universal_planes is set for atomic
drm/atomic: Hide drm.ko internal interfaces
drm: Atomic modeset ioctl
drm/atomic: atomic connector properties
drm/atomic: atomic plane properties
drm: small property creation cleanup
drm/atomic: atomic_check functions
drm: add atomic properties
drm: refactor getproperties/getconnector
drm: tweak getconnector locking
drm: add atomic_get_property
drm: add atomic_set_property wrappers
drm: get rid of direct property value access
drm: store property instead of id in obj attachment
drm: allow property validation for refcnted props
drm/atomic: Introduce state->obj backpointers
drm/atomic-helper: Again check modeset *before* plane states
drm/atomic-helper: Export both plane and modeset check helpers
Misc drm patches with mostly polish patches from Thierry, with a bit of
generic mode validation from Ville and a few other oddball things.
* tag 'topic/core-stuff-2014-12-19' of git://anongit.freedesktop.org/drm-intel: (25 commits)
drm: Include drm_crtc_helper.h in DocBook
drm: Make drm_crtc_helper.h standalone includible
drm: Move IRQ related fields to proper section
drm: Remove stale comment
drm: Do basic sanity checks for user modes
drm: Perform basic sanity checks on probed modes
drm: Reorganize probed mode validation
drm/doc: Remove duplicate "by"
drm/info: Remove unused code
drm/cache: Use wbinvd helpers
drm/plane-helper: Test for plane disable earlier
drm/doc: Document drm_add_modes_noedid() usage
drm: bit of spell-check / editorializing.
drm: Prefer sizeof(type) over sizeof type
drm: Remove useless else block
drm: Remove unneeded braces for single statement blocks
drm: Do not assign in if condition
drm: Prefer kmalloc_array() over kmalloc() with multiply
drm: Prefer kcalloc() over kzalloc() with multiply
drm: Miscellaneous checkpatch whitespace cleanups
...
A few msm fixes for 3.19:
* hdmi regulators fix
* hdmi fix for spurious HPD interrupts
* fix for sync atomic update after async update (which could show
up with a setcrtc following a pageflip)
* couple little Coccinelle cleanups
* 'msm-fixes-3.19' of git://people.freedesktop.org/~robclark/linux:
drm/msm/hdmi: rework HDMI IRQ handler
drm/msm/hdmi: enable regulators before clocks to avoid warnings
drm/msm/mdp5: update irqs on crtc<->encoder link change
drm/msm: block incoming update on pending updates
drm/msm: Deletion of unnecessary checks before the function call "release_firmware"
drm/msm: Deletion of unnecessary checks before two function calls
If crtc <-> encoder linkage changes, we could end up with the CRTC
listening for the wrong error or vsync irqs. Generally this problem
would correct itself relatively quickly, since we update the global
irqmask after dispatching irqs, but to be sure let the CRTC trigger
update_irq().
Signed-off-by: Rob Clark <robdclark@gmail.com>
We can't have multiple updates pending on a given CRTC, and we don't
want a sync update to race w/ an async update that preceeded it. So
keep track of which CRTCs have updates in flight, and block later
updates that would conflict.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Backmerge my drm-misc branch because of conflicts. Just simple stuff
but better to clear this out before I merge the other atomic patches.
Conflicts:
drivers/gpu/drm/drm_crtc.c
drivers/gpu/drm/drm_edid.c
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Useful since this way we can pass around just the state objects and
will get ther real object, too.
Specifically this allows us to again simplify the parameters for
set_crtc_for_plane.
v2: msm already has it's own specific plane_reset hook, don't forget
that one!
v3: Fixup kerneldoc, reported by 0-day builder.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com> (v2)
Tested-by: Rob Clark <robdclark@gmail.com> (v2)
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This essentially reverts
commit 934ce1c236
Author: Rob Clark <robdclark@gmail.com>
Date: Wed Nov 19 16:41:33 2014 -0500
drm/atomic: check mode_changed *after* atomic_check
Depending upon the driver both orders (or maybe even interleaving) is
required:
- If ->atomic_check updates ->mode_changed then helper_check_modeset
must be run afters.
- If ->atomic_check depends upon accurate adjusted dotclock values for
e.g. watermarks, then helper_check_modeset must be run first.
The failure mode in the first case is usually a totally angry hw
because the pixel format switching doesn't happen. The failure mode in
the later case is usually nothing, since in most cases the old
adjusted mode from the previous modeset wont be too far off to be a
problem. So just underruns and perhaps even just suboptimal (from a
power consumption) watermarks.
Furthermore in the transitional helpers we only call ->atomic_check
after the new modeset state has been fully set up (and hence
computed).
Given that asymmetry in expected failure modes I think it's safer to
go back to the older order. So do that and give msm a special check
function to compensate.
Also update kerneldoc to explain this a bit.
v2: Actually add the missing hunk Rob spotted.
v3: Move msm_atomic_check into msm_atomic.c, requested by Rob.
Cc: Rob Clark <robdclark@gmail.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Tested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
The release_firmware() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The functions framebuffer_release() and vunmap() perform also input
parameter validation. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Pull drm updates from Dave Airlie:
"Highlights:
- AMD KFD driver merge
This is the AMD HSA interface for exposing a lowlevel interface for
GPGPU use. They have an open source userspace built on top of this
interface, and the code looks as good as it was going to get out of
tree.
- Initial atomic modesetting work
The need for an atomic modesetting interface to allow userspace to
try and send a complete set of modesetting state to the driver has
arisen, and been suffering from neglect this past year. No more,
the start of the common code and changes for msm driver to use it
are in this tree. Ongoing work to get the userspace ioctl finished
and the code clean will probably wait until next kernel.
- DisplayID 1.3 and tiled monitor exposed to userspace.
Tiled monitor property is now exposed for userspace to make use of.
- Rockchip drm driver merged.
- imx gpu driver moved out of staging
Other stuff:
- core:
panel - MIPI DSI + new panels.
expose suggested x/y properties for virtual GPUs
- i915:
Initial Skylake (SKL) support
gen3/4 reset work
start of dri1/ums removal
infoframe tracking
fixes for lots of things.
- nouveau:
tegra k1 voltage support
GM204 modesetting support
GT21x memory reclocking work
- radeon:
CI dpm fixes
GPUVM improvements
Initial DPM fan control
- rcar-du:
HDMI support added
removed some support for old boards
slave encoder driver for Analog Devices adv7511
- exynos:
Exynos4415 SoC support
- msm:
a4xx gpu support
atomic helper conversion
- tegra:
iommu support
universal plane support
ganged-mode DSI support
- sti:
HDMI i2c improvements
- vmwgfx:
some late fixes.
- qxl:
use suggested x/y properties"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (969 commits)
drm: sti: fix module compilation issue
drm/i915: save/restore GMBUS freq across suspend/resume on gen4
drm: sti: correctly cleanup CRTC and planes
drm: sti: add HQVDP plane
drm: sti: add cursor plane
drm: sti: enable auxiliary CRTC
drm: sti: fix delay in VTG programming
drm: sti: prepare sti_tvout to support auxiliary crtc
drm: sti: use drm_crtc_vblank_{on/off} instead of drm_vblank_{on/off}
drm: sti: fix hdmi avi infoframe
drm: sti: remove event lock while disabling vblank
drm: sti: simplify gdp code
drm: sti: clear all mixer control
drm: sti: remove gpio for HDMI hot plug detection
drm: sti: allow to change hdmi ddc i2c adapter
drm/doc: Document drm_add_modes_noedid() usage
drm/i915: Remove '& 0xffff' from the mask given to WA_REG()
drm/i915: Invert the mask and val arguments in wa_add() and WA_REG()
drm: Zero out DRM object memory upon cleanup
drm/i915/bdw: Fix the write setting up the WIZ hashing mode
...
The ->load_lut() callback is optional, therefore a dummy implementation
is not needed.
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In most situations it will be useful to have the old state passed to the
->atomic_update() callback. For example if a plane is being disabled the
new state's .crtc field will be NULL, but some drivers may rely on this
field to program the CRTCs registers.
v2: rename variable to old_plane_state and remove redundant comment as
suggested by Daniel Vetter, remove an Exynos hunk that doesn't apply to
drm-next and add a hunk for pending MSM mdp5 changes
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On mdp4 there is a single global LAYERMIXER_IN_CFG register. The
previous logic to share that between multiple crtcs didn't actually
handle plane-disable very well. Easier just to look at all of the
crtcs each time.
Signed-off-by: Rob Clark <robdclark@gmail.com>
When disabling the interface (INTF), the change doesn't latch until next
vblank, so we need to wait for vblank.
Also, to be pedantic, in the crtc, set all the mixer stages to unused.
It shouldn't really matter, since at this point we have already disabled
the INTF and waited for necessary vblank.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Convert mdp5 over to atomic helpers. Extend/wrap drm_plane_state to
track plane zpos and to keep track of the needed when applying the
atomic update. In mdp5's plane->atomic_check() we also need to check
for updates which require SMP reallocation, in order to trigger full
modeset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
For example, use 'struct mdp5_smp *' everywhere instead of 'void *', but
only declare it as 'struct mdp5_smp;' in common headers, so the struct
body is still private. The accomplishes the desired modularity while
still letting the compiler provide some type checking for us.
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 currently support one single CRTC with its private pipe.
This change allows the configuration of multiple CRTCs with
the possibility to attach several public planes to these CRTCs.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The hardware configuration modification from a version to another
is quite consequent. Introducing a configuration module
(mdp5_cfg) may make things more clear and easier to access when a
new hardware version comes up.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The Shared Memory Pool (SMP) has its own limitation, features and
state. Some examples are:
- the number of Memory Macro Block (MMB) and their size
- the number of lines that can be fetched
- the state of MMB currently allocated
- the computation of number of blocks required per plane
- client IDs ...
In order to avoid private data to be overwritten by other modules,
let's make these private to the SMP module.
Some of these depend on the hardware configuration, let's add them
to the mdp5_config struct.
In some hw configurations, some MMBs are statically tied to RGB
pipes and cannot be re-allocated dynamically. This change
introduces the concept of MMB static usage and makes sure that
dynamic MMB requests are dimensioned accordingly.
A note on passing a pipe pointer, instead of client IDs:
Client IDs are SMP-related information. Passing PIPE information
to SMP lets SMP module to find out which SMP client(s) are used.
This allows the SMP module to access the PIPE pointer, which can
be used for FIFO watermark configuration.
By the way, even though REG_MDP5_PIPE_REQPRIO_FIFO_WM_* registers
are part of the PIPE registers, their functionality is to reflect
the behavior of the SMP block. These registers access is now
restricted to the SMP module.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
A left-over from prior to component framework. The original intent was
to deal with hdmi getting unloaded before the master component, but that
isn't really going to work anyways. These days with the component
framework taking care to unload the master component first, we don't
have to worry about this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
The core clock rate depends on the hw configuration. Once we have
read the hardware revision, we can set the core clock to its
maximum value.
Before then, the clock is set at a rate supported by all MDP5
revisions.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
For mdp5, the irqs of hdmi/eDP/dsi0/dsi1 blocks get routed through the
mdp block. In order to decouple hdmi/eDP/etc, register an irq domain
in mdp5. When hdmi/dsi/etc are used with mdp4, they can directly setup
their irqs in their DT nodes as normal. When used with mdp5, instead
set the mdp device as the interrupt-parent, as in:
mdp: qcom,mdss_mdp@fd900000 {
compatible = "qcom,mdss_mdp";
interrupt-controller;
#interrupt-cells = <1>;
...
};
hdmi: qcom,hdmi_tx@fd922100 {
compatible = "qcom,hdmi-tx-8074";
interrupt-parent = <&mdp>;
interrupts = <8 0>; /* MDP5_HW_INTR_STATUS.INTR_HDMI */
...
};
There is a slight awkwardness, in that we cannot disable child irqs
at the mdp level, they can only be cleared in the child block. So
you must not use threaded irq handlers in the child. I'm not sure
if there is a better way to deal with that.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Register offsets have changed between a3xx and a4xx GPUs.
To be able access these registers in common code, we create
a lookup table, and set of read-write APIs to access the
register through the lookup table.
Signed-off-by: Aravind Ganesan <aravindg@codeaurora.org>
[robclark: remove REG_ADRENO_UNDEFINED, just use zero, and minor
tweaks for latest generated headers]
Signed-off-by: Rob Clark <robdclark@gmail.com>
Use pre-computed iova when unmapping, to reduce the places we assume iova
and mmap offset are (at the moment) the same. And get rid of an extra
drm_gem_free_mmap_offset() call (since it is already called from
drm_gem_object_release())
Signed-off-by: Rob Clark <robdclark@gmail.com>
It's a problem that can't happen yet, since we don't support any
multi-planar formats yet. But let's avoid nasty surprises when the
time comes.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Atomic wants to split the prepare/pin from where we actually program the
scanout address (so that any part that can fail is done synchronously).
Add some fb/gem apis to make this easier to use from the kms parts.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Give ourselves a way to wait for certain fence #.. makes it easier to
wait on a set of bo's, which we'll need for atomic.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Simplify things a bit for atomic, gets rid of some bookkeeping, and
makes the code cleaner.
TODO move iterator macro somewhere common.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Since we are configuring things via MDP4_PIPE regs in the plane, it seems
like setting the dimensions of the primary plane on the OVLP/DMA regs in
crtc is unnecessary. This will make life easier when we want to do a
nofb modeset.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently forcing the video mode from the kernel command line (for example
video=HDMI-A-1:1280x720-16@60) does not correctly set the number of bits
per pixel. This is due to a rather aggressive override in
msm_fbdev_create(). This is a particular problem for Android bring up
because the software EGL fallbacks don't support 32bpp.
Since the overrides are actually the default values anyway then this
problem can be trivially fixed by removing the overrides completely.
Change was tested by dd'ing a test image to /dev/fb0 with no video=
(still 32bpp), video=1920x1080-32@60, video=1920x1080-24@60 and
video=1920x1080-16@60 .
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Currently msm does not implement gem_prime_mmap. Without this it is not
possible to draw onto a dma-buf from userspace (making its very hard to
implement the Android rendering model).
Fixing this is just a matter of adding a little boilerplate.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Split up hdmi_init() into hdmi_init() (done at hdmi sub-device
bind/probe time) and hdmi_modeset_init() done from master driver's
modeset_init().
Anything that can fail due to dependencies on other drivers which
may be missing or not probed yet should go in hdmi_init(), so that
devm error/cleanup paths work properly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Move anything that can fail after call to base class msm_gpu_init().
This way, if we fail, active_list has already been initialized so we
don't trip 'WARN_ON(!list_empty(&gpu->active_list))' in
msm_gpu_cleanup().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Fixes a potential error, spotted by Felipe with randconfig:
-----
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c: In function ‘mdp4_kms_init’:
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:2: error: implicit declaration \
of function ‘devm_regulator_get_exclusive’ [-Werror=implicit-function-declaration]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
drivers/gpu/drm/msm/mdp/mdp4/mdp4_kms.c:384:16: error: assignment makes \
pointer from integer without a cast [-Werror]
mdp4_kms->vdd = devm_regulator_get_exclusive(&pdev->dev, "vdd");
^
-----
Also add a brief comment explaining the use of _get_exclusive()
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we're using lists instead of kfifo to store drm flip-work tasks
we do not need the size parameter passed to drm_flip_work_init function
anymore.
Moreover this function cannot fail anymore, we can thus remove the return
code.
Modify drm_flip_work_init users to take account of these changes.
[airlied: fixed two unused variable warnings]
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
v2: Don't forget git add, noticed by David.
Cc: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Acked-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
If VRAM carveout is used, due to no IOMMU, we should have a default
value for msm.vram so that we don't simply crash.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
There is currently a nested function in Russel King's tree
for the msm HDMI driver.
The last nested function was removed from the Linux kernel
when the Thinkpad driver was fixed.
I believe nested functions are not desired upstream, and it
also breaks compilation with clang so here is a patch to
change the nested function into static function. The patch
works with both clang and gcc.
Signed-off-by: Mark Charlebois <charlebm@gmail.com>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Add ptr to list of interesting registers to 'struct adreno_gpu' and use
that to move most of the debugfs show and register dump bits down into
adreno_gpu. This will avoid duplication as support for additional
adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Push a few bits down into adreno_gpu so they won't have to be duplicated
as support for additional adreno generations is added.
Signed-off-by: Rob Clark <robdclark@gmail.com>
LVDS panel support uses the LCDC (parallel) encoder. Unlike with HDMI,
there is not a separate LVDS block, so no need to split things into a
bridge+connector. Nor is there is anything re-used with mdp5.
Note that there can be some regulators shared between HDMI and LVDS (in
particular, on apq8064, ext_3v3p), so we should not use the _exclusive()
variants of devm_regulator_get().
The drm_panel framework is used for panel-specific driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
In particular, blend_setup() should not overwrite the other crtc's mixer
settings. Also, the encoder needs to be able to specify the mixer-id
explicitly, since both LVDS and DTV use 'INTF_LVDC_DTV', so we cannot
guess the mixer-id from the interface.
Signed-off-by: Rob Clark <robdclark@gmail.com>
One step closer to dropping all the drm_bus_* code:
Add a driver->set_busid() callback and make all drivers use the generic
helpers. Nouveau is the only driver that uses two different bus-types with
the same drm_driver. This is totally broken if both buses are available on
the same machine (unlikely, but lets be safe). Therefore, we create two
different drivers for each platform during module_init() and set the
set_busid() callback respectively.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the missing unlock before return from function msm_fbdev_create()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Rob Clark <robdclark@gmail.com>
This avoids a problem seen with weston (for example) where the display
gets stuck in "black screen" if starting weston first thing after boot.
Possibly mdp5 needs something similar. The downstream android fbdev
driver always requests DMA_E (or DMA_P) when display is active, rather
than only enabling it on-demand as the drm driver does, which I believe
has the same end result.
Signed-off-by: Rob Clark <robdclark@gmail.com>
87e956e9 changed the fault handler to return -ENOSYS, which causes the
iommu driver to print out a huge splat. Which wouldn't be quite so bad
if nothing ever faulted. But seems like some EXA composite operations
generate quite a lot of (seemingly harmless) faults. That is probably a
userspace problem, but the huge increase in verbosity from iommu fault
dumps makes things kind of unusable.
We probably should actually log *some* message (not conditional on
drm.debug). But ratelimit it.
Signed-off-by: Rob Clark <robdclark@gmail.com>
HDMI_MUX_EN gpio is requested. If an error occurs, the same name
should be printed (HDMI_MUX_EN) instead of HDMI_MUX_SEL (typo).
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Rob Clark <robdclark@gmail.com>
lpm-mux is programmed to enable HDMI connector
on the docking station for S805 chipset based
devices.
Signed-off-by: Beeresh Gopal <gbeeresh@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
MDP5 has several functional blocks (ie: VIG/RGB pipes, LMs, ...).
From one revision to another, these blocks' base addresses might
change due to the number of instances present in the MDP5 hw.
A way of dealing with these offset changes is to introduce
dynamic offsets 'per block'.
This change adds support for the new revision of MDP5: v1.3.
The idea is to define one hw config per MDP version and select
either one of them at runtime, after reading the MDP5 version.
Once the MDP version is known, 'per block' dynamic offsets
are initialized through a global pointer, which is then used for
read/write register access.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
Somewhere along the way, the firmware loader sprouted another lock
dependency, resulting in possible deadlock scenario:
&dev->struct_mutex --> &sb->s_type->i_mutex_key#2 --> &mm->mmap_sem
which is problematic vs things like gem mmap.
So introduce a separate mutex to synchronize gpu init.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel IOMMU had a non-standard way of dealing with multiple
devices and multiple ports/contexts. We don't need that on upstream
kernel, so rip out the crazy.
Note that we have to move the pinning of the ringbuffer to after the
IOMMU is attached. No idea how that managed to work properly on the
downstream kernel.
For now, I am leaving the IOMMU port name stuff in place, to simplify
things for folks trying to backport latest drm/msm to device kernels.
Once we no longer have to care about pre-DT kernels, we can drop this
and instead backport upstream IOMMU driver.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Downstream kernel holds this clk via a fake-parent relationship.
Upstream clock framework requires that we hold it explicitly.
Signed-off-by: Rob Clark <robdclark@gmail.com>
On downstream kernel the clk driver directly bangs hdmi phy registers.
For upstream kernel, we need to model this as a clock and register with
the clock framework.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Now that we (almost) have enough dependencies in place (MMCC, RPM, etc),
add necessary DT support so that we can use drm/msm on upstream kernel.
v2: update for review comments
v3: rebase on component helper changes
Signed-off-by: Rob Clark <robdclark@gmail.com>
This change implements msm drm specific fb_mmap function for fb device
to properly map the fb address to userspace.
Signed-off-by: Hai Li <hali@codeaurora.org>
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com> (+ minor comment tweak)
This changes activates the iommu support for MDP5, through the
platform config structure.
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
To implement hotplug detection in a race-free manner, drivers must call
drm_kms_helper_poll_init() before hotplug events can be triggered. Such
events can be triggered right after any of the encoders or connectors
are initialized. At the same time, if the drm_fb_helper_hotplug_event()
helper is used by a driver, then the poll helper requires some parts of
the FB helper to be initialized to prevent a crash.
At the same time, drm_fb_helper_init() requires information that is not
necessarily available at such an early stage (number of CRTCs and
connectors), so it cannot be used yet.
Add a new helper, drm_fb_helper_prepare(), that initializes the bare
minimum needed to allow drm_kms_helper_poll_init() to execute and any
subsequent hotplug events to be processed properly.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There's no need for this to be modifiable. Make it const so that it can
be put into the .rodata section.
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://people.freedesktop.org/~dvdhrm/linux:
drm/omap: remove null test before kfree
drm/bochs: replace ALIGN(PAGE_SIZE) by PAGE_ALIGN
drm/ttm: recognize ARM arch in ioprot handler
drm: enable render-nodes by default
drm/ttm: remove declaration of ttm_tt_cache_flush
drm/gem: remove misleading gfp parameter to get_pages()
drm/omap: use __GFP_DMA32 for shmem-backed gem
drm/i915: use shmem helpers if possible
Conflicts:
drivers/gpu/drm/drm_stub.c
misc core patches picked up by Daniel and Jani.
* tag 'topic/core-stuff-2014-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/fb-helper: Remove unnecessary list empty check in drm_fb_helper_debug_enter()
drm/fb-helper: Redundant info->fix.type_aux setting in drm_fb_helper_fill_fix()
drm/debugfs: add an "edid_override" file per connector
drm/debugfs: add a "force" file per connector
drm: add register and unregister functions for connectors
drm: fix uninitialized acquire_ctx fields (v2)
drm: Driver-specific ioctls range from 0x40 to 0x9f
drm: Don't export internal module variables
drm_gem_get_pages() currently allows passing a 'gfp' parameter that is
passed to shmem combined with mapping_gfp_mask(). Given that the default
mapping_gfp_mask() is GFP_HIGHUSER, it is _very_ unlikely that anyone will
ever make use of that parameter. In fact, all drivers currently pass
redundant flags or 0.
This patch removes the 'gfp' parameter. The only reason to keep it is to
remove flags like __GFP_WAIT. But in its current form, it can only be used
to add flags. So to remove __GFP_WAIT, you'd have to drop it from the
mapping_gfp_mask, which again is stupid as this mask is used by shmem-core
for other allocations, too.
If any driver ever requires that parameter, we can introduce a new helper
that takes the raw 'gfp' parameter. The caller'd be responsible to combine
it with mapping_gfp_mask() in a suitable way. The current
drm_gem_get_pages() helper would then simply use mapping_gfp_mask() and
call the new helper. This is what shmem_read_mapping_pages{_gfp,} does
right now.
Moreover, the gfp-zone flag-usage is not obvious: If you pass a modified
zone, shmem core will WARN() or even BUG(). In other words, the following
must be true for 'gfp' passed to shmem_read_mapping_pages_gfp():
gfp_zone(mapping_gfp_mask(mapping)) == gfp_zone(gfp)
Add a comment to drm_gem_read_pages() explaining that constraint.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Update MSM's DRM driver to use the component match support rather than
add_components.
Reviewed-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If probe fails after IOMMU is attached, we need to detach in order to
clean up properly. Before this change, IOMMU faults would occur if the
probe failed (-EPROBE_DEFER).
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
use mm.h definition
Cc: David Airlie <airlied@linux.ie>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The clock driver usually complains when a clock is being prepared
before setting its rate. It is the case here for "core_clk" which
needs to be set at 19.2 MHz before we attempt a prepare_enable().
Signed-off-by: Stephane Viau <sviau@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Rob Clark <robdclark@gmail.com>
