Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enough space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Set CONFIG_COUNTER_FREQUENCY according to COUNTER_FREQUENCY in
config header file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
[trini: Re-run migration]
There is no reason for disabling I-cache and D-cache
in SPL.
Remove the unneeded CONFIG_SPL_SYS_ICACHE_OFF and
CONFIG_SPL_SYS_DCACHE_OFF options.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add gpio hog support for board-specific gpio lines:
- put hogs in u-boot.dtsi so as to keep the regular dts files
in sync with the kernel. The hogs will not be put in the kernel
as that makes them un-usable by userspace as well as
re-initializes them to dt defaults overriding changes which may
have been done by bootloader commands.
- specify gpio names and initial config
- enable GPIO_HOG
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Enable USB support for host controller and various USB ethernet
devices.
Example usage of USB Mass Storage (UMS) support:
u-boot=> mmc list
FSL_SDHC: 0
FSL_SDHC: 1
FSL_SDHC: 2 (eMMC)
u-boot=> ums 0 mmc 2
UMS: LUN 0, dev mmc 2, hwpart 0, sector 0x0, count 0xe30000
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use PREBOOT as well. This allows a customer to just set fdt_board as
on any other module to customize the device tree for his carrier
board.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This fixes the following crash when run on a Colibri iMX7S aka solo:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:
The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.
While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case a customer wants to set fdtfile currently preboot overrides it
always with preboot just before the bootdelay. Use test -n to check
if fdtfile is already set and only set it if nothing got touched manually
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
For recovery purpose allow booting via SDP over USB as well.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Add missing support of FIT-images and enable a verbosity for
this feature.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As video support is very specific depending on the exact display
customisation we decided to disable video support for all out modules
by default.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Update the current uDPU defconfig with following changes:
* Disable CONFIG_SPI_BOOT, its not needed for booting and the device boots
from eMMC anyway.
* Disable CONFIG_SYS_CONSOLE_INFO_QUIET, there is no need to diverge from
other boards by not priting the console device
* Enable CONFIG_CMD_MTD in order to allow use of the MTD tool
* Disable CONFIG_CMD_MTDPARTS, with MTD now being able to parse partitions
from DTS there is no need for it, the default MTDPARTS were incorrect
anyway
* Enable CONFIG_MMC_HS200_SUPPORT, the eMMC used support both HS200 and
HS400 modes, so enable at least HS200 because Xenon driver does not
support HS400 currently
* Replace CONFIG_SPI_FLASH_BAR with CONFIG_SPI_FLASH_SFDP_SUPPORT
Utilize SFDP parsing instead of relying on the extended address registers
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
Allow to read OTP bits via U-Boot fuse command on all Armada 3720 boards.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
As explained in commit 4af2a33ee5 ("cmd: gpio: Make `gpio input`
return pin value again") the `gpio input` is used in scripts to obtain
the value of a pin, despite the fact that CMD_RET_FAILURE is
indistinguishable from a valid pin value.
To be able to detect failures and properly use the value of a GPIO in
scripts we introduce the `gpio read` command that sets the variable
`name` to the value of the pin. Return code of the `gpio read` command
can be used to check for CMD_RET_SUCCESS or CMD_RET_FAILURE.
CONFIG_CMD_GPIO_READ is used to enable the `gpio read` command.
Signed-off-by: Diego Rondini <diego.rondini@kynetics.com>
Since this box is SystemReady compliant enable ISO_PARTITION which is
needed to start some installers (e.g Fedora). While at it enable EXT4
as well which is a common filesystem for targets
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
This commit adds the default configuration file and
relevant description for a MK808 board.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
The current UEFI capsule updation code uses two GUID values, one for
FIT images, and one for raw images across platforms. This logic is
being changed to have GUID values per image, per platform. Change the
tests for the capsule update code to reflect this change. The GUID
values now used are the ones specific to the sandbox platform -- one
for the u-boot image, and another for the u-boot environment image.
Install the FMP instance for raw images on the sandbox variant for
testing the capsule update code. Install the FMP instance for the FIT
images on the sandbox64 and sandbox_flattree variant for testing
capsule update for FIT images. This is being done by splitting the
capsule update script for FIT and raw images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Increase the malloc pool on sandbox in order to avoid spurious errors
such as:
___________________ test_ut[ut_dm_dm_test_video_comp_bmp32] ____________________
test/py/tests/test_ut.py:43: in test_ut
assert output.endswith('Failures: 0')
E AssertionError: assert False
E + where False = <built-in method endswith of str object at 0x7f5de85efb20>('Failures: 0')
E + where <built-in method endswith of str object at 0x7f5de85efb20> = 'Test: dm_test_video_comp_bmp32: video.c\r\r\nSDL renderer does not exist\r\r\ntest/dm/video.c:86, compress_frame_buff..._test_video_comp_bmp32(): 2024 == compress_frame_buffer(uts, dev): Expected 0x7e8 (2024), got 0x1 (1)\r\r\nFailures: 2'.endswith
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Drop legacy #define CONFIG_DRIVER_DM9000 from board include/configs/
and enable the same in Kconfig configs/ .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently the space between kernel_addr_r and the fdt_addr_r is only 32MB.
To have enought space to load kernel images bigger than 32MB change the
variables to a feasible value.
The new environment variables layout is based on the scheme from
"include/configs/ti_armv7_common.h".
The CONFIG_SYS_LOAD_ADDR value is set to 0x42000000. With that we have
the same value as for the kernel_addr_r.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
