Commit Graph

82753 Commits

Author SHA1 Message Date
Oliver Graute
55be8433d5 imx: imx8qm-rom7720: switch to binman
Switch to use binman to pack images

Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
2022-11-09 17:12:32 +01:00
Fabio Estevam
20cc70a84f wandboard: Select DM_SERIAL
The conversion to DM_SERIAL is mandatory, so select this
option.

Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-11-09 17:12:31 +01:00
Fabio Estevam
f827f84d3f wandboard: Pass mmc aliases
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.

After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.

This causes a regression in which the SD card cannot be found anymore:

Since commit  the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)

CPU:   Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM:  2 GiB
Core:  62 devices, 17 uclasses, devicetree: separate
PMIC:  PFUZE100 ID=0x10
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment

Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.

Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-11-09 17:12:31 +01:00
Adam Ford
f2fe18fa38 configs: imx8mn_beacon: Enable SPL_DM_PMIC_BD71837
To properly operate the Nano with LPDDR4 at 1.6GHz, the
voltage needs to be adjusted before DDR is initialized.
Enable the PMIC in SPL to do this.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-11-08 17:35:00 +01:00
Adam Ford
899f291bd1 configs: imx8mn_beacon: Re-align memory to standard imx8mn settings
The imx8mn_beacon board does not use the same memory map as the reference
design from NXP or other imx8mn boards.  As such, memory is more limited
in SPL.

Moving SPL_BSS_START_ADDR and SPL_STACK to default locations increases
the amount of available meory for the SPL stack.  Doing this allows
the board to no longer define CONFIG_MALLOC_F_ADDR.

Since SYS_LOAD_ADDR also does not align with other boards, move it too.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
dbd5ca2e46 imx8mm: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
f067b59743 imx8mn: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
0b42fdca2d imx8mp: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
cb9b70fd2f imx8mq: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
ed7bda5710 imx8ulp: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
62f96866d3 imxrt1050: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Note: Nowadays, the intent is for them regular device trees to just be
synchronised from them Linux kernel device trees and any and all U-Boot
specific changes need to go into the -u-boot.dtsi device tree include
files which BTW get included automatically by the U-Boot build system.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
59a4e7fd88 imxrt1020: migrate to build system included -u-boot.dtsi
Migrate to using automatic build system included -u-boot.dtsi device
tree include files.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
2022-11-08 17:35:00 +01:00
Marcel Ziswiler
05e22e2804 vf610: synchronise device tree with linux
Synchronise device tree with linux v6.1-rc3.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
4a71b9c286 configs: imx8m{m,n,p}_venice: disable autoload
disable network autoload

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
765f6f1895 imx: imx8m{m,n,p}_venice: migrate to CONFIG_EXTRA_ENV_TEXT
Move the majority of the environment from the board headers to
a separate text file.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
e9e03e7984 configs: imx8m{m, n}_venice: remove unneeded CONFIG_FEC_MXC_PHYADDR
The IMX8M based Venice boards all have device-tree fec nodes that
use proper dt with a phy-handle pointing to a phy with reg assigned
to the proper phy address.

There is no need to keep using the CONFIG_FEC_MXC_PHYADDR hack when
a proper dt is used - remove it.

This was previously done in commit 400eebf10d
("configs: imx8m{m, n}_venice: remove unneeded CONFIG_FEC_MXC_PHYADDR")
but got clobbered by commit 6889412ad5
("Convert CONFIG_SYS_BARGSIZE to Kconfig")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
37fa34f727 configs: imx8mn_venice.h: remove unused ifdef
remove unused ifdef left behind after commit ca3369df71
("configs: drop CONFIG_SPL_ABORT_ON_RAW_IMAGE")

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
9414097ab7 configs: imx8mn_venice: fix include header protection
Fix typo in the include header protection.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Tim Harvey
630abef2f1 board: gateworks: venice: remove redundance adjustment of thermal trip points
commit 0543a1ed27 ("imx8m: fixup thermal trips") moved updating the
thermal trip points to all IMX8M so we can remove it from our board
specific dt config.

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-11-08 17:35:00 +01:00
Baruch Siach
cf8ffbe36f mx6cuboxi: migrate to DM_SERIAL
Add the needed DT overrides to enable UART in SPL.

Cc: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Tested-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-11-08 17:35:00 +01:00
Marek Vasut
b177a2626e ARM: imx: Add version variable to DHSOM
Enable insertion of version variable into U-Boot environment on DHSOM,
to make it possible to check U-Boot version e.g. in U-Boot scripts.

Signed-off-by: Marek Vasut <marex@denx.de>
2022-11-08 17:35:00 +01:00
Martyn Welch
c8f3402ad2 arm: imx8mp: Initial MSC SM2S iMX8MP support
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
2022-11-08 17:34:47 +01:00
Martyn Welch
e055457759 drivers: power: pmic: Enable use of rn5t567 PMIC in SPL
The support added later in this series tweaks the PMIC voltages in the
SPL. Enable support for the rn5t567 in SPL builds to allow this to be done
cleanly.

Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2022-11-07 22:45:05 +01:00
Martyn Welch
da470ddbb3 drivers: power: pmic: Add support for rn5t568 PMIC
Add support for the rn5t568 PMIC to the rn5t567 driver.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <j80.chung@samsung.com>
2022-11-07 22:45:05 +01:00
Martyn Welch
c92c3a4453 ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP
The i.MX8MP SoC contains 2 more i2c buses. Add support for the
configuration of these buses.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2022-11-07 22:45:05 +01:00
Martyn Welch
03a7a82970 imx8m: USDHC3 base address definition for i.MX8MP
The i.MX8MP also has USDHC3, allow access to the relvant base address
definition.

Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
2022-11-07 22:45:05 +01:00
Adam Ford
78f34793ed imx: imx8mm-beacon: Move Environment to eMMC partition 2
The downstream U-Boot distributed by Beacon stores the environment
in the eMMC and the end of partition 2.  This allow the environment
to stay on the SOM regardless of the boot source.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-11-07 22:45:05 +01:00
Adam Ford
3a7943a90c imx: imx8mm-beacon: Enable USB booting via SDP
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL.  Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode.  Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-11-07 22:45:05 +01:00
Adam Ford
b6c8a28090 imx: imx8mm_beacon: Eliminate a few extras to free up SPL space
There are a few functions which are not essential for use in
SPL, but they take up enough space to make other preferred
features not fit.  Remove the extras.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-11-07 22:45:05 +01:00
Adam Ford
a5685ea488 imx: imx8mn-beacon: Fix out of spec voltage
The DDR is configured for LPDDR4 running at 1.6GHz which requires
the voltage on the PMIC to rise a bit before initializing LPDDR4
or it will be running out of spec.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-11-07 22:45:04 +01:00
Adam Ford
4dbe07f275 regulator: bd718x7: Only bind children when PMIC_CHILDREN is enabled
If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error.  Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.

Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.

Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
2022-11-07 22:45:04 +01:00
Matthias Schiffer
975f4117d5 ARM: mx7: psci: fix suspend/resume e10133 workaround
The e10133 workaround was broken in two places:

- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
  While the old register values were saved, the actual masking was
  missing.
- imx_udelay() expects the system counter to run at its base frequency,
  but the system counter is switched to a lower frequency earlier in
  psci_system_suspend(), leading to a much longer delay than intended.
  Replace the call with an equivalent loop (linux-imx 5.15 does the same)

This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.

Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
2022-11-07 22:45:04 +01:00
Loic Poulain
a887f2ac3e configs: imx8m: Enable CONFIG_ARMV8_CRYPTO support
This enables armv8 crypto extension usage for SHA1/SHA256.

Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-11-07 22:45:04 +01:00
Tom Rini
88bd8ee106 Prepare v2023.01-rc1
Signed-off-by: Tom Rini <trini@konsulko.com>
2022-11-07 15:27:03 -05:00
Tom Rini
1bb3d8b201 configs: Resync with savedefconfig
Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-11-07 11:58:57 -05:00
Tom Rini
6de63bd38b Merge https://source.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: Support for 98DX25xx/98DX35xx (AlleyCat5) (Chris)
- Makefile: Rename u-boot-spl.kwb to u-boot-with-spl.kwb (Pali)
- armada: dts: Add clock to armada-ap80x uart1 (Hamish)
2022-11-07 07:56:07 -05:00
Chris Packham
6cc8b5db40 arm: mvebu: Add RD-AC5X board
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
  * SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
  * SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
  * PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
  * SR1: 88E2540*4
  * SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
  port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
  connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
  Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
  solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)

Signed-off-by: Chris Packham <judge.packham@gmail.com>
2022-11-07 07:46:28 +01:00
Chris Packham
7d7bb99e22 arm: mvebu: Support for 98DX25xx/98DX35xx SoC
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
2022-11-07 07:46:28 +01:00
Chris Packham
c249938214 pinctrl: mvebu: Add AlleyCat5 support
This uses the same IP block as the Armada-8K SoCs.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:46:28 +01:00
Chris Packham
515fe1ee4e usb: ehci: ehci-marvell: Support for marvell,ac5-ehci
Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
the fact that the ac5 does not have the mbus infrastructure the 32-bit
SoCs have and ensure USB_EHCI_IS_TDI is selected.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:46:28 +01:00
Chris Packham
aaee5720f2 net: mvneta: Add support for AlleyCat5
Add support for the AlleyCat5 SoC. This lacks the mbus from the other
users of the mvneta.c driver so a new compatible string is needed to
allow for a different window configuration.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:46:28 +01:00
Chris Packham
3988e6d6b1 arm: mvebu: Don't use CONFIG_TIMER on ARM64
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.

Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:46:12 +01:00
Pali Rohár
87ac4b4b4c Makefile: Rename u-boot-spl.kwb to u-boot-with-spl.kwb
File name with pattern u-boot-spl* is used on all places except in kwb
image for binary with SPL-only code. Combined binary with both SPL and
proper U-Boot in other places has file name pattern u-boot-with-spl*.

Make it consistent also for kwb image and rename u-boot-spl.kwb to
u-boot-with-spl.kwb as this image contains both SPL and proper U-Boot code.

Also update documentation about file name changes.

Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:17:55 +01:00
Hamish Martin
497db3ad89 arm: armada: dts: Add clock to armada-ap80x uart1
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.

Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
2022-11-07 07:17:55 +01:00
Tom Rini
d332cd59f7 Pull request for efi-2023-01-rc1-4
Documentation:
 
 * Provide a document about security issue handling.
 
 UEFI:
 
 * Let networking support depend on NETDEVICES.
 * Discover if no efi_system_partition is set.
 
 Other:
 
 * MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
 -----BEGIN PGP SIGNATURE-----
 
 iQIyBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAmNnnfAACgkQxIHbvCwF
 GsRGhw/47xCMpdAm6FhVZrBTuh9WG43Jb9rpw1a86eaebysNcxATFbJ3uWWj2pJd
 duFPJVSxJ0yt0TAAZrCDnMU7epLLHRbBjOPAEyG2xjoVyJjJw04UG6P3iKbeY5Fs
 8IZFBQWmO602jdCnrJg8DGGwX4UfQqS0x2V8pSIW620+luH61bibKNUrT8KK7jAb
 NXan6Q08L9V3OjYEfCnHbnWWZbwt8ZlqVKYZ/8u6+LJTHAioU8SHJeRd7GxMDoGN
 SuT7647IGgyeYYncUWUY3/NbrXEm1oz/qm2I8QmCzin1ipMmYwh9mrW+gyu8bQyO
 y4fuJ1RvCB18dpFzoisK5WvjZSd0YsPQkqm3bJudbgNhBF9BmN32ywWRzXhaibO8
 +IoFQS84+sIXB4M17hAh422fePaEJ1Yis9Lj8CgAEgdcR1fHxNA5zHH9kwBNXvJd
 tjbaSin9Rw4iRFDDLRtgFeWSS+uBz51EwrqN/MTdgJw9wAQY3wGKqS1oHBFc3SLf
 igx9BoGioLox7YRd3u3Acr2IQvhHDL9TBSNAf7xF51/d4foKCZ8zC8iWx6Vf/Xj9
 lXRwOp4oawYipN/SSoNQGtRJj9uZmtWG3a19cyJru4ah1IgTNSSj/Xz79Go0aHj1
 ebb5Rd+0wMtyYzjeTFzrjuwav7ix2H/t6PUwUdW3QtiHPoKjhg==
 =MoPl
 -----END PGP SIGNATURE-----

Merge tag 'efi-2023-01-rc1-4' of https://source.denx.de/u-boot/custodians/u-boot-efi

Pull request for efi-2023-01-rc1-4

Documentation:

* Provide a document about security issue handling.

UEFI:

* Let networking support depend on NETDEVICES.
* Discover if no efi_system_partition is set.

Other:

* MAINTAINERS: add arch/arm/lib/*_efi.* to EFI_PAYLOAD.
2022-11-06 07:51:44 -05:00
Heinrich Schuchardt
53def68df5 efi_loader: AllocateAddress requires page address
AllocatePages() can be called with Type=AllocateAddress. Such a call can
only succeed if *Memory points to the address of an unallocated page range.

A call with *Memory being an address that is not page aligned must not
succeed. The UEFI specification requires returning EFI_OUT_OF_RESOURCES
if the requested pages cannot be allocated.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
2022-11-06 10:50:04 +01:00
Masahisa Kojima
0b4cbeba59 test/py: efi_secboot: Remove unnecessary cert-to-efi-hash-list option
'cert-to-efi-hash-list -t 0' does not work as expected, it produces
indeterminate timestamp.

  $ cert-to-efi-hash-list -t 0 -s 256 db.crt dbx_hash.crl
  TimeOfRevocation is 0-113-0 00:00:255

If we need the CRL revoked for all the time, just don't specify
'-t' option.

  $ cert-to-efi-hash-list -s 256 db.crt dbx_hash.crl
  TimeOfRevocation is 0-0-0 00:00:00

Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
2022-11-06 10:50:04 +01:00
Heinrich Schuchardt
2b55ad304d efi_loader: discover if no efi_system_partition is set
Variable efi_system_partition holds the efi_system_partition. Currently it
is initialized as:

    {
      .uclass_id = 0 = UCLASS_ROOT,
      .denum = 0,
      .part = 0,
    }

This indicates that host 0:0 is the efi_system_partition and we see output
like:

    => bootefi hello
    ** Bad device specification host 0 **
    Couldn't find partition host 0:0

To identify that no EFI system partition has been set use UCLASS_INVALID.

Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
2022-11-06 10:50:04 +01:00
AKASHI Takahiro
023d9c9393 efi_loader: remove CONFIG_EFI_SETUP_EARLY
Since the commit a9bf024b29 ("efi_loader: disk: a helper function to
create efi_disk objects from udevice"), CONFIG_EFI_SETUP_EARLY option is
by default on and will never be turned off.

So just remove this option.

Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
2022-11-06 10:50:04 +01:00
Jan Kiszka
77b5c4a5b1 efi_loader: Let networking support depend on NETDEVICES
CONFIG_NET does not imply that there are actually network devices
available, only CONFIG_NETDEVICES does. Changing to this dependency
obsoletes the check in Kconfig because NETDEVICES means DM_ETH.

Fixes: 0efe1bcf5c ("efi_loader: Add network access support")
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2022-11-06 10:50:04 +01:00