The 104-idio-16 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for mapping gpio-reg gpios to interrupts. This may be a
non-linear mapping - some gpios in the register may not even have
corresponding interrupts associated with them, so we need to pass an
array.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a simple, generic, single register fixed-direction GPIO driver.
This is able to support a single register with a mixture of inputs
and outputs.
This is different from gpio-mmio and gpio-74xx-mmio:
* gpio-mmio doesn't allow a fixed direction, it assumes there is always
a direction register.
* gpio-74xx-mmio only supports all-in or all-out setups
* gpio-74xx-mmio is DT only, this needs to support legacy too
* they don't double-read when getting the GPIO value, as required by
some implementations that this driver supports
* we need to always do 32-bit reads, which bgpio doesn't guarantee
* the current output state may not be readable from the hardware
register - reading may reflect input status but not output status.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow gpiolib to read back the current IO direction configuration by
implementing the .get_direction callback. This, in part, allows
debugfs to report the complete true hardware state rather than the
software state.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use IO accessors to access the SA1100 registers rather than accessing
them directly.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use sa11x0_gpio_set_wake() to set the PWER register, as provided by
Dmitry some time back.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mentioned flags are dedicated solely for consumer API.
Replace them by explicit values.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Made a !bang clamp to (0,1) instead of infix ? operator]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now the wm831x-core has basic DT support we can update this driver to
allow use of the GPIOs within a device tree system.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
GPIO ACPI library is going to be stricter about resources, thus, expand
comment regarding "reset" GPIO resource in this driver to clarify its
usage in ACPI case.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For sake of better maintenance sort the headers by alphabetical order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce ->get_direction() callback for the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
[Removed use of GPIOF_DIR* flags]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the BIT macro instead of explicitly shifting bits for some added
clarity.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO-based NAND controller on National Instruments 169445 hardware
exposes a set of simple lines for the control signals.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This just deletes the Moxa ART driver and replaces it with the
more versatile Faraday FTGPIO010 driver.
Make this default on for ARCH_GEMINI and ARCH_MOXART so we do
not get Kconfig glitches.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Gemini driver is actually a driver for the Faraday Technology
FTGPIO010 IP block. We rename the driver and the Kconfig symbol and
put in a a new compatible string for the Moxa ART SoC that is also
using this IP block.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the open coded registration of the cdev and dev with the
new device_add_cdev() helper. The helper replaces a common pattern by
taking the proper reference against the parent device and adding both
the cdev and the device.
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an interrupt occurs on an MCP23S08 chip, the INTF register will only
contain one bit as causing the interrupt. If more than two pins change at
the same time on the chip, this causes one of the pins to not be reported.
This patch fixes the logic for checking if a pin has changed, so that
multiple pins will always cause more than one change.
Cc: stable@vger.kernel.org
Signed-off-by: Robert Middleton <robert.middleton@rm5248.com>
Tested-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A modern compiler should know better when to inline, so drop the inline
keywords.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use unsigned int instead of plain unsigned as reported by checkpatch.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
While this isn't an issue according to checkpatch two styles are used.
Add a blank line to the block comments missing a blank line at the start
so multiline block comments look the same across the file.
Signed-off-by: Ralph Sennhauser <ralph.sennhauser@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When acpi_dev_gpio_irq_get gets called with an index of say 2, it should
not care if acpi_get_gpiod for index 0 or 1 returns -EPROBE_DEFER.
This allows drivers which request a gpioint with index > 0 to function
if there is no gpiochip driver (loaded) for gpioints with a lower index.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's unusual to have error checking like (ret <= 0) in cases when
counting GPIO resources. In case when it's mandatory we propagate the
error (-ENOENT), otherwise we don't use the result.
This makes consistent behaviour across all possible variants called in
gpiod_count().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of this platform.
Update compile dependencies and ACPI ID to reflect this change.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
[Drop depreciation of ARCH_VULCAN]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The zx gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ws16c48 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pl061 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The etraxfs gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ath79 gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Aban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The bcm-kona gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a
real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The 104-dio-48e gpio driver currently implements an irq_chip for
handling interrupts; due to how irq_chip handling is done, it's
necessary for the irq_chip methods to be invoked from hardirq context,
even on a a real-time kernel. Because the spinlock_t type becomes a
"sleeping" spinlock w/ RT kernels, it is not suitable to be used with
irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The altera gpio driver currently implements an irq_chip for handling
interrupts; due to how irq_chip handling is done, it's necessary for the
irq_chip methods to be invoked from hardirq context, even on a a real-time
kernel. Because the spinlock_t type becomes a "sleeping" spinlock w/ RT
kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw spinlock.
Signed-off-by: Julia Cartwright <julia@ni.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
PC/104 drivers should be hidden on machines which do not support PC/104
devices. This patch adds the PC104 Kconfig option as a dependency for
the relevant PC/104 device driver Kconfig options.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the interrupt descriptors it allocates. Fix
it by using the resource managed version of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the resource managed variant of irq_alloc_descs() and remove the
code manually freeing allocated interrupt descriptors.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use device resource managed variants of irq_alloc_descs() and
request_irq() and remove the code manually freeing irq resources.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the allocated interrupt descriptors. Fix it by
using a resource managed variant of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver never frees the irq descriptors it allocates. Fix it by
using a resource managed variant of irq_alloc_descs().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the resource managed variant of irq_alloc_descs(). This allows us
to remove gpio_mockup_remove().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Bamvor Jian Zhang <bamvor.zhangjian@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Current code does not set output level in exar_direction_output, fix it.
Also move the direction_output/direction_input code block to avoid forward
declaration for exar_set_value().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Introduce device managed variant of acpi_dev_add_driver_gpios() and its
counterpart acpi_dev_remove_driver_gpios().
The functions in most cases are used in driver's ->probe() and
->remove() callbacks, that's why it's useful to have managed variant of
them.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Rafael J. Wysocki <rjw@rjwysocki.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove extra 'l' in "successfull".
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When a threaded irq handler is chained attached to one of the gpio
pins when configure for level irq the altera_gpio_irq_leveL_high_handler
does not mask the interrupt while being handled by the chained irq.
This resulting in the threaded irq not getting enough cycles to complete
quickly enough before the irq was disabled as faulty. handle_level_irq
should be used in this situation instead of handle_simple_irq.
In gpiochip_irqchip_add set default handler to handle_bad_irq as
per Documentation/gpio/driver.txt. Then set the correct handler in
the set_type callback.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When CONFIG_PM_SLEEP is disabled, we get a warning about unused functions:
drivers/gpio/gpio-xgene.c:155:12: warning: 'xgene_gpio_resume' defined but not used [-Wunused-function]
static int xgene_gpio_resume(struct device *dev)
^~~~~~~~~~~~~~~~~
drivers/gpio/gpio-xgene.c:142:12: warning: 'xgene_gpio_suspend' defined but not used [-Wunused-function]
static int xgene_gpio_suspend(struct device *dev)
The warnings are harmless and can be avoided by simplifying the code and marking
the functions as __maybe_unused.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
copy_from_user() returns the number of bytes remaining to be copied but
we want to return negative error codes on failue.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set the gpio_chip parent property since some recent functions
such as devprop_gpiochip_set_names() can use it.
Signed-off-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Next generation of X-Gene SoC's GPIO hardware register map is very
similar to DW GPIO. It only differs by a few register addresses.
This patch modifies DW GPIO driver to accommodate the difference
in a few register addresses.
Signed-off-by: Hoan Tran <hotran@apm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do.
This is a treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace
ABI correctly reflect the current in-kernel consumer of a pin
taken using this abstraction. This is a treewide change also
updating all users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide
change also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing
a backend into the pin control subsystem that were also merged
into the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace
to fully test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime
PM support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations.
-----BEGIN PGP SIGNATURE-----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=O81I
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
The PCI BAR0 and BAR1 for the PCI-IDIO-16 hold information for the PLX
9052 bridge chip on the device. The PCI BAR2 holds the necessary base
address for I/O control of the PCI-IDIO-16. This patch corrects the PCI
BAR index mismatch for the PCI-IDIO-16 GPIO driver.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 has a PCI device ID code of 0x0DC8. It is
incorrect to use the PCI device ID code of the ACCES PCI-IIRO-8
(0x0F00). This patch fixes the said PCI device ID code mismatch.
Fixes: 02e74fc040 ("gpio: Add GPIO support for the ACCES PCI-IDIO-16")
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Create a debugfs directory for every mockup chip and a single file
for every line. Writing (0 or 1) to these files allows the user to
inject line events (falling or rising edge respectively).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setup a dummy irqchip that will allow us to inject line events for
testing purposes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In order to allow testing line lookup by name from user space, add
a new boolean parameter that indicates whether we want the lines to
be named. The name is created by concatenating the chip name and the
line offset value.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Moving a couple of lines around allows us to shrink the code a bit
while keeping the same functionality.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The following patch tries to improve the readability of the mockup
driver.
The driver is called gpio-mockup, so add the same prefix to all
functions and structures.
Add some newlines and use a temporary pointer in gpio_mockup_add().
Drop the name of the direction enum and rename the enum values to
better reflect their purpose.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES PCI-IDIO-16 device provides 32 lines of digital I/O (16 lines
of optically-isolated digital inputs for AC and DC control signals, and
16 lines of solid state switch digital outputs). An interrupt is
generated when any of the inputs change state (low to high or high to
low). Input filter control is not supported by this driver, and input
filters are deactivated by this driver.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1736f75d35 is a (v2) patch which had
unresolved review comments[1]. Address the comments by removing the use
of macros from the consumer header (this patch represents the diff
between v2 and v3[2]).
[1] https://lkml.org/lkml/2017/1/26/337
[2] https://lkml.org/lkml/2017/1/26/786
Fixes: 1736f75d35 ("gpio: aspeed: Add banks Y, Z, AA, AB and AC")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
devm_fwnode_get_gpiod_from_child() currently allows GPIO users to
request a GPIO that is defined in a child fwnode instead of directly in
the device fwnode.
Extend this API by adding the devm_fwnode_get_index_gpiod_from_child()
helper which does the same except you can also specify an index in case
the 'xx-gpios' property describe several GPIOs.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver now using devm_regmap_init/devm_regmap_init_i2c, so it needs
to select REGMAP/REGMAP_I2C accordingly.
Fixes: ("3d84fdb3f0b5 gpio: mcp23s08: use regmap")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-By: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the WinSystems WS16C48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the Diamond Systems
GPIO-MM. This should make it easier for users to identify which GPIO
line corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDIO-16.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-IDI-48.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch sets the gpio_chip names option with an array of GPIO line
names that match the manual documentation for the ACCES 104-DIO-48E.
This should make it easier for users to identify which GPIO line
corresponds to a respective GPIO pin on the device.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
ws16c48_remove function. Now that the ws16c48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
gpiomm_remove function. Now that the gpiomm_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idio_16_remove function. Now that the idio_16_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
idi_48_remove function. Now that the idi_48_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting driver_data was necessary to access private data in the
dio48e_remove function. Now that the dio48e_remove function is gone,
driver_data is no longer used. This patch removes the relevant code.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use regmap API to save some lines of codes and have
debugfs support for all of the MCP's registers.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the ws16c48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call with
the devm_gpiochip_add_data call. In addition, the gpiomm_remove function
has been removed as no longer necessary due to the use of the relevant
devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idio_16_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the idi_48_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devm_ resource manager functions allow memory to be automatically
released when a device is unbound. This patch takes advantage of the
resource manager functions and replaces the gpiochip_add_data call and
request_irq call with the devm_gpiochip_add_data call and
devm_request_irq call respectively. In addition, the dio48e_remove
function has been removed as no longer necessary due to the use of the
relevant devm_ resource manager functions.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is less straight-forward than one would hope, as some banks only
have 4 pins rather than 8, others are output only, yet more (W and
X, already supported) are input-only, and in the case of the g4 SoC bank
AC doesn't exist.
Add some structs to describe the varying properties of different banks
and integrate mechanisms to deny requests for unsupported
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed SoCs have more GPIOs than can be represented with A-Z. The
documentation uses two letter names such as AA and AB, so make the names
a three-character array in the bank struct to accommodate this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Exar XR17V352/354/358 chips have 16 multi-purpose inputs/outputs which
can be controlled using gpio interface.
Add the gpio specific code.
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The WinSystems WS16C48 provides registers where 8 lines of GPIO may be
set at a time. This patch add support for the set_multiple callback
function, thus allowing multiple GPIO output lines to be set more
efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Diamond Systems GPIO-MM series provides registers where 8 lines of
GPIO may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-IDIO-16 series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ACCES 104-DIO-48E series provides registers where 8 lines of GPIO
may be set at a time. This patch add support for the set_multiple
callback function, thus allowing multiple GPIO output lines to be set
more efficiently in groups.
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This is a heavy edit/rewrite of the GPIO driver for the Gemini
SoC from arch/arm/mach-gemini/gpio.c.
This rewrite uses all the best-in-class helper like generic
GPIO and GPIOLIB_IRQCHIP and has been tested on ITian Square One
Gemini-based NAS/router.
Cc: Janos Laube <janos.dev@gmail.com>
Cc: Paulius Zaleckas <paulius.zaleckas@gmail.com>
Cc: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With the current redesign of driver it's not necessary to have
custom .xlate() as the gpiolib will assign default of_gpio_simple_xlate().
Suggested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update GPIO driver to support Multiple GPIO controllers by updating
the base of subsequent GPIO chips with total of previous chips
gpio count so that gpio_add_chip gets unique numbers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Davinci GPIO driver is implemented to work with one monolithic
Davinci GPIO platform device which may have up to Y(144) gpios.
The Davinci GPIO driver instantiates number of GPIO chips with
max 32 gpio pins per each during initialization and one IRQ domain.
So, the current GPIO's opjects structure is:
<platform device> Davinci GPIO controller
|- <gpio0_chip0> ------|
... |--- irq_domain (hwirq [0..143])
|- <gpio0_chipN> ------|
Current driver creates one chip for every 32 GPIOs in a controller.
This was a limitation earlier now there is no need for that. Hence
redesigning the driver to create one gpio chip for all the ngpio
in the controller.
|- <gpio0_chip0> ------|--- irq_domain (hwirq [0..143]).
The previous discussion on this can be found here:
https://www.spinics.net/lists/linux-omap/msg132869.html
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio2regs is written making an assumption that driver supports only
one instance of gpio controller. Removing this and adding a generic
array so as to support multiple instances of gpio controllers.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of function intel_gpio_runtime_idle() is here (in the
same file):
static const struct dev_pm_ops intel_gpio_pm_ops = {
SET_RUNTIME_PM_OPS(NULL, NULL, intel_gpio_runtime_idle)
};
And when CONFIG_PM is not set, the macro SET_RUNTIME_PM_OPS expands to
nothing, causing the following compiler warning:
drivers/gpio/gpio-intel-mid.c:324:12: warning: ‘intel_gpio_runtime_idle’
defined but not used [-Wunused-function]
static int intel_gpio_runtime_idle(struct device *dev)
Fix it by annotating the function with __maybe_unused.
Signed-off-by: Augusto Mecking Caringi <augustocaringi@gmail.com>
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The helper function for adding a GPIO chip compiles in a lockdep
key for debugging, the same key is needed for nested chips as
well.
The macro construction is unreadable, replace this with two
static inlines instead.
The _gpiochip_irqchip_add prefixed function is not helpful,
rename it with gpiochip_irqchip_add_key() that tell us what the
function is actually doing.
Fixes: d245b3f9bd ("gpio: simplify adding threaded interrupts")
Cc: Roger Quadros <rogerq@ti.com>
Reported-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Reported-by: Roger Quadros <rogerq@ti.com>
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Casting a pointer to an int is not portable, and provokes a compiler
warning. Cast to unsigned long instead to avoid the warning.
drivers/gpio/gpio-mvebu.c: In function 'mvebu_gpio_probe':
drivers/gpio/gpio-mvebu.c:662:17: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
soc_variant = (int) match->data;
^
This will be needed when building gpio-mvebu for Armada 7k/8k ARM64
SoCs.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add optional reset-gpios pin control. If present, de-assert the
specified reset gpio pin to bring the chip out of reset.
v2:
- Specify that reset signal to PCA953x chip is active low, in
binding doc.
- reorder includes in gpio-pca953x.c.
- remove dev_err() on devm_gpiod_get_optional() error return.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
container_of() does pointer math on the pointer that's passed in.
If it were to return a NULL pointer the value passed in would
need to be perfectly offset from 0 to make that so. Remove these
checks because they don't make sense.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It seems the code had been changed, but description left untouched.
Update description of the struct acpi_gpio_info and relative comments
accordingly.
Fixes: commit 52044723cd ("ACPI / gpio: Add irq_type when a GPIO is used as an interrupt")
Cc: Christophe RICARD <christophe.ricard@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The macro for_each_set_bit() effectively looks up to the next
set bit in array of bits.
Instead of open coding that switch to for_each_set_bit() in
gpio_chip_set_multiple().
While here, make gpio_chip_set_multiple() non-destructive
against its parameters. We are safe since all callers, i.e.
gpiod_set_array_value_complex(), handle that already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
davinci_gpio_controller struct has set_data, in_data, clr_data
members that are assigned and never used.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We have already a global array of possible GPIO suffixes. Use it here instead
of another copy of them.
Unfortunately this will not reduce the memory footprint, though allows to easy
maintain list in only one place.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When listing multiple GPIOs in the "gpios" property of a GPIO hog, only
the first GPIO is affected. The user is left clueless about the
dysfunctioning of the other GPIOs specified.
Fix this by adding and documenting support for specifying multiple
GPIOs in a single GPIO hog.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When removing a gpiochip that uses GPIO hogging (e.g. by unloading the
chip's DT overlay), a warning is printed:
gpio gpiochip8: REMOVING GPIOCHIP WITH GPIOS STILL REQUESTED
This happens because gpiochip_free_hogs() is called after the gdev->chip
pointer is reset to NULL. Hence __gpiod_free() cannot determine the
chip in use, and cannot clear flags nor call the optional chip-specific
.free() callback.
Move the call to gpiochip_free_hogs() up to fix this.
Cc: stable@vger.kernel.org
Fixes: ff2b135922 ("gpio: make the gpiochip a real device")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Building with an old toolchain, I ran into this warning:
WARNING: vmlinux.o(.text+0x63eef0): Section mismatch in reference
from the function mxs_gpio_probe() to the function
.init.text:mxs_gpio_init_gc()
Clearly the annotation is wrong, since the function is called from the
non-init probe, so let's remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the chip name buffer is allocated on the stack and the
address of the buffer is passed to the gpio framework. It's invalid
after probe() returns, so the sysfs label attribute displays garbage.
Use devm_kasprintf() for each string instead.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This variable is not used outside this module. Make it static.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently gpio modules are runtime-resumed at probe time. This means the
gpio module will be active all the time (except during system suspend,
if not configured as a wake-up source).
While an R-Car Gen2 gpio module retains pins configured for output at
the requested level while put in standby mode, gpio register cannot be
accessed while suspended. Unfortunately pm_runtime_get_sync() cannot be
called from all contexts where gpio register access is needed. Hence
move the Runtime PM handling from probe/remove time to gpio request/free
time, which is probably the best we can do.
On r8a7791/koelsch, gpio modules 0, 1, 3, and 4 are now suspended during
normal use (gpio2 is used for LEDs and regulators, gpio5 for keys, gpio6
for SD-Card CD & WP, gpio7 for keys and regulators).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
[Niklas: s/gpio_to_priv(chip)/gpiochip_get_data(chip)/]
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This enables Runtime PM handling for interrupts.
By setting the parent_device in struct irq_chip genirq will call the
pm_runtime_get/put APIs when an IRQ is requested/freed.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Core changes:
- Simplify threaded interrupt handling: instead of passing
numbed parameters to gpiochip_irqchip_add_chained() we
create a new call: gpiochip_irqchip_add_nested() so the two
types are clearly semantically different. Also make sure
that all nested chips call gpiochip_set_nested_irqchip()
which is necessary for IRQ resend to work properly if
it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so
that anything != 0 will be send down to the driver as "1"
not the value passed in.
- ACPI can now support naming of GPIO lines, hogs and holes
in the GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem
and was moved over to a combined GPIO+pinctrl driver in the
pinctrl subsystem.
New features:
- Various cleanups to various drivers.
-----BEGIN PGP SIGNATURE-----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=2UpT
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Luinus Walleij:
"Bulk GPIO changes for the v4.10 kernel cycle:
Core changes:
- Simplify threaded interrupt handling: instead of passing numbed
parameters to gpiochip_irqchip_add_chained() we create a new call:
gpiochip_irqchip_add_nested() so the two types are clearly
semantically different. Also make sure that all nested chips call
gpiochip_set_nested_irqchip() which is necessary for IRQ resend to
work properly if it happens.
- Return error on seek operations for the chardev.
- Clamp values set as part of gpio[d]_direction_output() so that
anything != 0 will be send down to the driver as "1" not the value
passed in.
- ACPI can now support naming of GPIO lines, hogs and holes in the
GPIO lists.
New drivers:
- The SX150x driver was deemed unfit for the GPIO subsystem and was
moved over to a combined GPIO+pinctrl driver in the pinctrl
subsystem.
New features:
- Various cleanups to various drivers"
* tag 'gpio-v4.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (49 commits)
gpio: merrifield: Implement gpio_get_direction callback
gpio: merrifield: Add support for hardware debouncer
gpio: chardev: Return error for seek operations
gpio: arizona: Tidy up probe error path
gpio: arizona: Remove pointless set of platform drvdata
gpio: pl061: delete platform data handling
gpio: pl061: move platform data into driver
gpio: pl061: rename variable from chip to pl061
gpio: pl061: rename state container struct
gpio: pl061: use local state for parent IRQ storage
gpio: set explicit nesting on drivers
gpio: simplify adding threaded interrupts
gpio: vf610: use builtin_platform_driver
gpio: axp209: use correct register for GPIO input status
gpio: stmpe: fix interrupt handling bug
gpio: em: depnd on ARCH_SHMOBILE
gpio: zx: depend on ARCH_ZX
gpio: x86: update config dependencies for x86 specific hardware
gpio: mb86s7x: use builtin_platform_driver
gpio: etraxfs: use builtin_platform_driver
...
By default all pins are configured to use a glitch filter. Writing 1 to the
certain bit of the specific register might be useful in case someone needs to
bypass the glitch filter completely for a given GPIO pin.
This patch adds support for that in the Intel Merrifield GPIO driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO chardev is used for management tasks (allocating line and event
handles) and does neither support read() nor write() operations. Hence it
does not make much sense to allow seek operations.
Currently the chardev uses noop_llseek() for its seek implementation. This
function does not move the pointer and simply returns the current position
(always 0 for the GPIO chardev). noop_llseek() is primarily meant for
devices that can not support seek, but where there might be a user that
depends on the seek() operation succeeding. For newly added devices that
can not support seek operations it is recommended to use no_llseek(), which
will return an error. For more information see commit 6038f373a3
("llseek: automatically add .llseek fop").
Unfortunately this was overlooked when the GPIO chardev ABI was introduced.
But it is highly unlikely that since then userspace applications have
appeared that rely on being able to perform non-failing seek operations on
a GPIO chardev file descriptor. So it should be safe to change from
noop_llseel() to no_seek(). Also use nonseekable_open() in the chardev
open() callback to clear the FMODE_SEEK, FMODE_PREAD and FMODE_PWRITE flags
from the file. Neither of these should be set on a file that does not
support seek operations.
Cc: stable@vger.kernel.org
Fixes: 3c702e9987 ("gpio: add a userspace chardev ABI for GPIOs")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is some unnecessary complexity in the error path which now things
are converted to devm is actually very simple. This patch simplifies
things.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use the gpio chip private data in all the callbacks so remove this
redundant line of code.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Platform data is a remnant of board files and all boards using
the PL061 have been migrated to use device tree or ACPI instead.
The custom mechanism to set line by default as inputs/outputs has
been superceded by the GPIO-internal hogging mechanism.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No boardfile defines any PL061 platform data anymore: the
Integrator IM/PD-1 includes the file but is not making use
of the struct. Let's delete the include and all references,
then move the platform data into the driver for later
consolidation into the driver state container.
The only resource defined by the IM/PD-1 is the IRQ which
is passed through the AMBA PrimeCell bus abstraction
struct amba_device.
Cc: arm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Rename the local variable "chip" referring to the struct pl061
state container to "pl061": we already have gpio_chip and irq_chip
in the driver, we are needlessly adding yet another "chip" to
the confusion.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PL061 state container is named "pl061_gpio", let's rename it
to simply pl061. Less is more.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver is poking around in the struct gpio_chip internals,
which is a no-no. Use a variable in the local state container.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The ADNP, CrystalCove and WhiskeyCove are all nested GPIO
irqchips, but were avoiding to connect the parent IRQ to
the gpiochip. This works, but is kind of sloppy as the
child IRQs are not marked as having the parent IRQ as
parent.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This tries to simplify the use of CONFIG_GPIOLIB_IRQCHIP when
using threaded interrupts: add a new call
gpiochip_irqchip_add_nested() to indicate that we're dealing
with a nested rather than a chained irqchip, then create a
separate gpiochip_set_nested_irqchip() to mirror
the gpiochip_set_chained_irqchip() call to connect the
parent and child interrupts.
In the nested case gpiochip_set_nested_irqchip() does nothing
more than call irq_set_parent() on each valid child interrupt,
which has little semantic effect in the kernel, but this is
probably still formally correct.
Update all drivers using nested interrupts to use
gpiochip_irqchip_add_nested() so we can now see clearly
which these users are.
The DLN2 driver can drop its specific hack with
.irq_not_threaded as we now recognize whether a chip is
threaded or not from its use of gpiochip_irqchip_add_nested()
signature rather than from inspecting .can_sleep.
We rename the .irq_parent to .irq_chained_parent since this
parent IRQ is only really kept around for the chained
interrupt handlers.
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Octavian Purdila <octavian.purdila@intel.com>
Cc: Daniel Baluta <daniel.baluta@intel.com>
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Ajay Thomas <ajay.thomas.david.rajamanickam@intel.com>
Cc: Semen Protsenko <semen.protsenko@globallogic.com>
Cc: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Phil Reid <preid@electromag.com.au>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO input status was read from control register
(AXP20X_GPIO[210]_CTRL) instead of status register (AXP20X_GPIO20_SS).
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
commit 43db289d00 ("gpio: stmpe: Rework registers access")
reworked the STMPE register access so as to use
[STMPE_IDX_*_LSB + i] to access the 8bit register for a
certain bank, assuming the CSB and MSB will follow after
the enumerator. For this to work the index needs to go from
(size-1) to 0 not 0 to (size-1).
However for the GPIO IRQ handler, the status registers we read
register MSB + 3 bytes ahead for the 24 bit GPIOs and index
registers from MSB upwards and run an index i over the
registers UNLESS we are STMPE1600.
This is not working when we get to clearing the interrupt
EDGE status register STMPE_IDX_GPEDR_[LCM]SB: it is indexed
like all other registers [STMPE_IDX_*_LSB + i] but in this
loop we index from 0 to get the right bank index for the
calculations, and we need to just add i to the MSB.
Before this, interrupts on the STMPE2401 were broken, this
patch fixes it so it works again.
Cc: stable@vger.kernel.org
Cc: Patrice Chotard <patrice.chotard@st.com>
Fixes: 43db289d00 ("gpio: stmpe: Rework registers access")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The GPIO_EM is part of the Renesas SoCs so depend on the arch.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
[Changed to depend on ARCH_EMEV2]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set GPIO_ZX to depend on ARCH_ZX as it's SOC specific.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The devices here are specific to x86 so lets depend on x86.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Adding max20024 compatible string to the device id list
to support both max77620 and max20024 devices.
Signed-off-by: Venkat Reddy Talla <vreddytalla@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
