There are multiple instances of GPIO device tree nodes of the form:
foo {
compatible = "acme,foo";
...
gpio0: gpio0@xxxxxxxx {
compatible = "acme,bar";
...
gpio-controller;
};
gpio1: gpio1@xxxxxxxx {
compatible = "acme,bar";
...
gpio-controller;
};
...
}
bazz {
my-gpios = <&gpio0 ...>;
}
Case 1: The driver for "foo" populates struct device for these gpio*
nodes and then probes them using a driver that binds with "acme,bar".
This driver for "acme,bar" then registers the gpio* nodes with gpiolib.
This lines up with how DT nodes with the "compatible" property are
typically converted to struct devices and then registered with driver
core to probe them. This also allows the gpio* devices to hook into all
the driver core capabilities like runtime PM, probe deferral,
suspend/resume ordering, device links, etc.
Case 2: The driver for "foo" doesn't populate struct devices for these
gpio* nodes before registering them with gpiolib. Instead it just loops
through its child nodes and directly registers the gpio* nodes with
gpiolib.
Drivers that follow case 2 cause problems with fw_devlink=on. This is
because fw_devlink will prevent bazz from probing until there's a struct
device that has gpio0 as its fwnode (because bazz lists gpio0 as a GPIO
supplier). Once the struct device is available, fw_devlink will create a
device link with gpio0 device as the supplier and bazz device as the
consumer. After this point, since the gpio0 device will never bind to a
driver, the device link will prevent bazz device from ever probing.
Finding and refactoring all the instances of drivers that follow case 2
will cause a lot of code churn and it is not something that can be done
in one shot. In some instances it might not even be possible to refactor
them cleanly. Examples of such instances are [1] [2].
This patch works around this problem and avoids all the code churn by
simply setting the fwnode of the gpio_device and creating a stub driver
to bind to the gpio_device. This allows all the consumers to continue
probing when the driver follows case 2.
[1] - https://lore.kernel.org/lkml/20201014191235.7f71fcb4@xhacker.debian/
[2] - https://lore.kernel.org/lkml/e28e1f38d87c12a3c714a6573beba6e1@kernel.org/
Fixes: e590474768 ("driver core: Set fw_devlink=on by default")
Cc: Marc Zyngier <maz@kernel.org>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20210122193600.1415639-1-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When set_config changes a line from input to output debounce is
implicitly disabled, as debounce makes no sense for outputs, but the
debounce period is not being cleared and is still reported in the
line info.
So clear the debounce period when the debouncer is stopped in
edge_detector_stop().
Fixes: 65cff70464 ("gpiolib: cdev: support setting debounce")
Cc: stable@vger.kernel.org
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Moreover this code duplicates gpio-pxa since the IP has been derived
from XScale implementation. If anybody wants to resurrect this
it has to be part of gpio-pxa.c.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Commit efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip") moved the
Tegra GPIO driver to the generic GPIO IRQ chip infrastructure and made
the IRQ domain hierarchical, so the driver needs to pull in the support
infrastructure via the GPIOLIB_IRQCHIP and IRQ_DOMAIN_HIERARCHY Kconfig
options.
Fixes: efcdca286eef ("gpio: tegra: Convert to gpio_irq_chip")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This is the only driver in the kernel source tree that depends on
IRQ_DOMAIN_HIERARCHY instead of selecting it. Since it is not a
visible Kconfig symbol, depending on it (expecting a user to
set/enable it) doesn't make much sense, so change it to select
instead of "depends on".
Fixes: 96868dce64 ("gpio/sifive: Add GPIO driver for SiFive SoCs")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: linux-gpio@vger.kernel.org
Cc: Thierry Reding <treding@nvidia.com>
Cc: Greentime Hu <greentime.hu@sifive.com>
Cc: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The period is the sum of on and off values. That is, calculate period as
($on + $off) / clkrate
instead of
$off / clkrate - $on / clkrate
that makes no sense.
Reported-by: Russell King <linux@armlinux.org.uk>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 757642f9a5 ("gpio: mvebu: Add limited PWM support")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
gpiochip->to_irq method is redefined in gpiochip_add_irqchip.
A lot of gpiod driver's still define ->to_irq method, let's give
a gentle warning that they can no longer rely on it, so they can remove
it on ocassion.
Fixes: e0d8972898 ("gpio: Implement tighter IRQ chip integration")
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for BD9574MWF which is similar chip with BD9571MWV.
Note that BD9574MWF has additional features "RECOV_GPOUT",
"FREQSEL" and "RTC_IN", but supports GPIO function only.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
To simplify this driver, use dev_get_regmap() and
rid of using struct bd9571mwv.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Use the SPDX license identifier instead of a local description.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The usual pattern for the remove calls, like gpiod_remove_lookup_table(),
is to be NULL-aware, i.o.w. become a no-op whenever parameter is NULL.
Update gpiod_remove_lookup_table() call to follow this pattern.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The kernel test robot reports the following warning in [1]:
drivers/gpio/gpiolib-cdev.c: In function 'gpio_ioctl':
>>drivers/gpio/gpiolib-cdev.c:1437:1: warning: the frame size of 1040 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Refactor gpio_ioctl() to handle each ioctl in its own helper function
and so reduce the variables stored on the stack to those explicitly
required to service the ioctl at hand.
The lineinfo_get_v1() helper handles both the GPIO_GET_LINEINFO_IOCTL
and GPIO_GET_LINEINFO_WATCH_IOCTL, as per the corresponding v2
implementation - lineinfo_get().
[1] https://lore.kernel.org/lkml/202012270910.VW3qc1ER-lkp@intel.com/
Fixes: aad955842d ("gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips
now use the template struct gpio_irq_chip and pass that to the core
to be set up alongside the gpio_chip. We can finally get rid of
the old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME
(wall clock) timestamps. We have found solid use cases for
this, so we support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which
is pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device
tree client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for
register access.
-----BEGIN PGP SIGNATURE-----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=nrFU
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of the GPIO changes for the v5.11 kernel cycle:
Core changes:
- Retired the old set-up function for GPIO IRQ chips. All chips now
use the template struct gpio_irq_chip and pass that to the core to
be set up alongside the gpio_chip. We can finally get rid of the
old cruft.
- Some refactoring and clean up of the core code.
- Support edge event timestamps to be stamped using REALTIME (wall
clock) timestamps. We have found solid use cases for this, so we
support it.
New drivers:
- MStar MSC313 GPIO driver.
- HiSilicon GPIO driver.
Driver improvements:
- The PCA953x driver now also supports the NXP PCAL9554B/C chips.
- The mockup driver can now be probed from the device tree which is
pretty useful for virtual prototyping of devices.
- The Rcar driver now supports .get_multiple()
- The MXC driver dropped some legacy and became a pure device tree
client.
- The Exar driver was moved over to the IDA interface for
enumerating, and also switched over to using regmap for register
access"
* tag 'gpio-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
MAINTAINERS: Remove reference to non-existing file
gpio: hisi: Do not require ACPI for COMPILE_TEST
MAINTAINERS: Add maintainer for HiSilicon GPIO driver
gpio: gpio-hisi: Add HiSilicon GPIO support
gpio: cs5535: Simplify the return expression of cs5535_gpio_probe()
gpiolib: irq hooks: fix recursion in gpiochip_irq_unmask
dt-bindings: mt7621-gpio: convert bindings to YAML format
gpiolib: cdev: Flag invalid GPIOs as used
gpio: put virtual gpio device into their own submenu
drivers: gpio: amd8111: use SPDX-License-Identifier
drivers: gpio: amd8111: prefer dev_err()/dev_info() over raw printk
drivers: gpio: bt8xx: prefer dev_err()/dev_warn() over of raw printk
gpio: Add TODO item for debugfs interface
gpio: just plain warning when nonexisting gpio requested
tools: gpio: add option to report wall-clock time to gpio-event-mon
tools: gpio: add support for reporting realtime event clock to lsgpio
gpiolib: cdev: allow edge event timestamps to be configured as REALTIME
gpio: msc313: MStar MSC313 GPIO driver
dt-bindings: gpio: Binding for MStar MSC313 GPIO controller
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
...
- Add support for Intel's Platform Monitoring Technology (PMT)
- New Device Support
- Add support for PM660/PM660L to QCom SPMI PMIC
- Add support for lots of new devices to Kontron Core
- New Functionality
- Provide syscon_regmap_lookup_by_phandle_optional() to SysCon API
- Fix-ups
- Constify; da9xxx-core; intel_*, tps65xxx, wm8xxx-core, lp8788,
stmpe, sun4i-gpadc, 88pm800, hi655x-pmic, ioc3, etc
- Remove superfluous code; madera, tps65910
- Use raw APIs (rid abstractions); tps65911-comparator, tps65910
- Whitespace/formatting fix-ups; tps65910
- Device Tree changes/updates; bd71837-pmic, syscon
- Use helpers/APIs (no hand rolling); altera-sysmgr
- Mark of_match tables as __maybe_unused; twl6030-irq
- Fix spelling; si476x-core
- Bug Fixes
- Reset on resume to ensure known state; madera-core
- Correct ordering issues; madera-core, tps65910, kempld-core
- Remove erroneous passing of of_compatible strings; at91-usart
- Fix potential I2C adaptor leak; htc-i2cpld
- Correct errorneous defines; rt5033-private
- Resolve Kconfig issues; MFD_SL28CPLD, MFD_OMAP_USB_HOST
- Fix dev_err_probe() handling; stmfx
- Repair interrupt regression; motorola-cpcap
- Allow ACPI matching of DT tables; bcm590xx, da9xx, ene-kb3930,
fsl-imx25-tsadc, max77650,
mt6397-core, rt5033, stmfx,
max77686, sun4i-gpadc,
wm8994-core, axp20x-i2c
-----BEGIN PGP SIGNATURE-----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=Qp9q
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- Add support for Intel's Platform Monitoring Technology (PMT)
New Device Support:
- Add support for PM660/PM660L to QCom SPMI PMIC
- Add support for lots of new devices to Kontron Core
New Functionality:
- Provide syscon_regmap_lookup_by_phandle_optional() to SysCon API
Fix-ups:
- Constify; da9xxx-core; intel_*, tps65xxx, wm8xxx-core, lp8788,
stmpe, sun4i-gpadc, 88pm800, hi655x-pmic, ioc3, etc
- Remove superfluous code; madera, tps65910
- Use raw APIs (rid abstractions); tps65911-comparator, tps65910
- Whitespace/formatting fix-ups; tps65910
- Device Tree changes/updates; bd71837-pmic, syscon
- Use helpers/APIs (no hand rolling); altera-sysmgr
- Mark of_match tables as __maybe_unused; twl6030-irq
- Fix spelling; si476x-core
Bug Fixes:
- Reset on resume to ensure known state; madera-core
- Correct ordering issues; madera-core, tps65910, kempld-core
- Remove erroneous passing of of_compatible strings; at91-usart
- Fix potential I2C adaptor leak; htc-i2cpld
- Correct errorneous defines; rt5033-private
- Resolve Kconfig issues; MFD_SL28CPLD, MFD_OMAP_USB_HOST
- Fix dev_err_probe() handling; stmfx
- Repair interrupt regression; motorola-cpcap
- Allow ACPI matching of DT tables; bcm590xx, da9xx, ene-kb3930,
fsl-imx25-tsadc, max77650, mt6397-core, rt5033, stmfx, max77686,
sun4i-gpadc, wm8994-core, axp20x-i2c"
[ The PMT updates already came in through the x86 platform tree ]
* tag 'mfd-next-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (48 commits)
mfd: kempld-core: Add support for additional devices
mfd: si476x-core.h: Fix "regulator" spelling in comment
mfd: twl6030: Mark of_device_id table as maybe unused
mfd: axp20x: Skip of_device_id table when !CONFIG_OF
mfd: wm8994: Drop of_match_ptr from of_device_id table
mfd: sun4i: Drop of_match_ptr from of_device_id table
mfd: max77686: Drop of_match_ptr from of_device_id table
mfd: stmfx: Drop of_match_ptr from of_device_id table
mfd: rt5033: Drop of_match_ptr from of_device_id table
mfd: mt6397: Drop of_match_ptr from of_device_id table
mfd: max77650: Drop of_match_ptr from of_device_id table
mfd: fsl-imx25: Drop of_match_ptr from of_device_id table
mfd: ene-kb3930: Drop of_match_ptr from of_device_id table
mfd: da9150: Drop of_match_ptr from of_device_id table
mfd: da9063: Drop of_match_ptr from of_device_id table
mfd: da9062: Drop of_match_ptr from of_device_id table
mfd: da9055: Drop of_match_ptr from of_device_id table
mfd: bcm590xx: Drop of_match_ptr from of_device_id table
mfd: omap-usb: Depend on COMMON_CLK to fix compile tests
mfd: kempld-core: Check for DMI definition before ACPI
...
Make it clear that ACPI needs to be present only to get driver functional.
It is not required for compilation.
Fixes: 356b01a986 ("gpio: gpio-hisi: Add HiSilicon GPIO support")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201214165524.43843-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This GPIO driver is for HiSilicon's ARM SoC.
HiSilicon's GPIO controller support double-edge interrupt and multi-core
concurrent access.
ACPI table example for this GPIO controller:
Device (GPO0)
{
Name (_HID, "HISI0184")
Device (PRTA)
{
Name (_ADR, Zero)
Name (_UID, Zero)
Name (_DSD, Package (0x01)
{
Package (0x02)
{
"ngpios",
0x20
}
})
}
}
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Link: https://lore.kernel.org/r/1607934255-52544-2-git-send-email-luojiaxing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
irqchip shared with multiple gpiochips, leads to recursive call of
gpiochip_irq_mask/gpiochip_irq_unmask which was assigned to
rqchip->irq_mask/irqchip->irq_unmask, these happens becouse of
only irqchip->irq_enable == gpiochip_irq_enable is checked.
Let's add an additional check to make sure shared irqchip is detected
even if irqchip->irq_enable wasn't defined.
Fixes: a8173820f4 ("gpio: gpiolib: Allow GPIO IRQs to lazy disable")
Signed-off-by: Nikita Shubin <nikita.shubin@maquefel.me>
Link: https://lore.kernel.org/r/20201210070514.13238-1-nikita.shubin@maquefel.me
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
-----BEGIN PGP SIGNATURE-----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=RmnM
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.11-rc1
- several refactoring patches of the core gpiolib code
- add support for NXP PCAL9554B/C to gpio-pca953x
- allow probing mockup devices from device tree
- refactoring and improvements to gpio-rcar
- improvements to locking in gpio-tegra
- code shrink in gpiolib devres
- get the irq offset from device tree in gpio-sifive
- major refactoring of gpio-exar
- convert gpio-mvebu pwm access to regmap
- create a new submenu for virtual GPIO drivers
- fix clang fall-through warnings treewide
- minor driver refactoring and tweaks sprinkled all over
When reporting the state of a GPIO to userspace, we never check
for the actual validity of the line, meaning we report invalid
lines as being usable. A subsequent request will fail though,
which is an inconsistent behaviour from a userspace perspective.
Instead, let's check for the validity of the line and report it
as used if it is invalid. This allows a tool such as gpioinfo
to report something sensible:
gpiochip3 - 4 lines:
line 0: unnamed unused input active-high
line 1: unnamed kernel input active-high [used]
line 2: unnamed kernel input active-high [used]
line 3: unnamed unused input active-high
In this example, lines 1 and 2 are invalid, and cannot be used by
userspace.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201204164739.781812-2-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
EIC controller have unfixed numbers of banks on different Spreadtrum SoCs,
and each bank has its own base address, the loop of getting there base
address in driver should break if the resource gotten via
platform_get_resource() is NULL already. The later ones would be all NULL
even if the loop continues.
Fixes: 25518e024e ("gpio: Add Spreadtrum EIC driver support")
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201209055106.840100-1-zhang.lyra@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since we already have a few virtual GPIO drivers, and more to come,
this category deserves its own submenu.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
For logging in device contexts, dev_*() functions are preferred over
raw printk(), which also print out device name.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201203182423.5499-2-info@metux.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For logging in device contexts, dev_*() functions are preferred over
raw printk(), which also print out device name.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Link: https://lore.kernel.org/r/20201203182423.5499-1-info@metux.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The idea to create a debugfs to replace the aging and
dangerous sysfs ABI for hacking and tinkering came up
on the list.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201204083533.65830-1-linus.walleij@linaro.org
When trying to export an nonexisting gpio ID, the kernel prints out a
big warning w/ stacktrace, sounding like a huge problem. In fact it's
a pretty normal situation, like file or device not found.
So, just print a more relaxed warning instead.
changes v2: drop defining pr_fmt()
Signed-off-by: Enrico Weigelt <info@metux.net>
Link: https://lore.kernel.org/r/20201202133754.32045-1-info@metux.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using CLOCK_REALTIME as the source for event timestamps is crucial for
some specific applications, particularly those requiring timetamps
relative to a PTP clock, so provide an option to switch the event
timestamp source from the default CLOCK_MONOTONIC to CLOCK_REALTIME.
Note that CLOCK_REALTIME was the default source clock for GPIO until
Linux 5.7 when it was changed to CLOCK_MONOTONIC due to issues with the
shifting of the realtime clock.
Providing this option maintains the CLOCK_MONOTONIC as the default,
while also providing a path forward for those dependent on the pre-5.7
behaviour.
Suggested-by: Jack Winch <sunt.un.morcov@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20201014231158.34117-2-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a driver that supports the GPIO block found in
MStar/SigmaStar ARMv7 SoCs.
The controller seems to have enough register for 128 lines
but where they are wired up differs between chips and
no currently known chip uses anywhere near 128 lines so there
needs to be some per-chip data to collect together what lines
actually have physical pins attached and map the right names to them.
The core peripherals seem to use the same lines on the
currently known chips but the lines used for the sensor
interface, lcd controller etc pins seem to be totally
different between the infinity and mercury chips
The code tries to collect all of the re-usable names,
offsets etc together so that it's easy to build the extra
per-chip data for other chips in the future.
So far this only supports the MSC313 and MSC313E chips.
Support for the SSC8336N (mercury5) is trivial to add once
all of the lines have been mapped out.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Link: https://lore.kernel.org/r/20201129110803.2461700-4-daniel@0x0f.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mxs is a devicetree-only platform and hence it does not make use
of the id_table mechanism.
Get rid of the .id_table as it is unused.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201118191938.32693-1-festevam@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This assigns the .irq_set_affinity to the parent callback.
I assume the Tegra186 is an SMP system so this would be
beneficial.
I used the pattern making the hirerarchy tolerant for missing
parent as in Marc's earlier patch.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Vidya Sagar <vidyas@nvidia.com>
Link: https://lore.kernel.org/r/20201117213351.249668-2-linus.walleij@linaro.org
This assigns the .irq_set_affinity to the parent callback.
I assume the sifive GPIO can be used in systems with
SMP.
I used the pattern making the hirerarchy tolerant for missing
parent as in Marc's earlier patches.
Suggested-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Yash Shah <yash.shah@sifive.com>
Cc: Wesley W. Terpstra <wesley@sifive.com>
Link: https://lore.kernel.org/r/20201117213351.249668-1-linus.walleij@linaro.org
If users select sysfs support they get the character device
as well so that end-users cannot complain that they
"only have sysfs on my system". They should have the
character device at all times.
If someone is in so dire need of stripping out the
character device while still enabling the sysfs ABI they
can very well patch the kernel.
Also only show this obsolete option to expert users.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201110142724.14760-1-linus.walleij@linaro.org
Commit 2233bf7a92 ("gpio: mvebu: switch to regmap for register access")
changed most readl/writel registers access calls to the regmap API in
preparation for Armada 7K/8K support. PWM duration registers were left using
readl/writel, as the driver does not support PWM for Armada 7K/8K.
Switch PWM duration registers to regmap as first step in adding Armada 7K/8K
PWM functionality support.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to putting operation will result in a
reference leak here.
A new function pm_runtime_resume_and_get is introduced in
[0] to keep usage counter balanced. So We fix the reference
leak by replacing it with new funtion.
[0] dd8088d5a8 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
Fixes: c2df3de0d0 ("gpio: zynq: properly support runtime PM for GPIO used as interrupts")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
A similar check was added in gpiochip_generic_request, but not in free.
This has caused an imbalance count of request vs. free calls to the
pinctrl driver. This patch is targeted to fix that issue.
Fixes: 2ab73c6d83 ("gpio: Support GPIO controllers without pin-ranges")
Signed-off-by: Edmond Chung <edmondchung@google.com>
Signed-off-by: Andrew Chant <achant@google.com>
Signed-off-by: Will McVicker <willmcvicker@google.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
Fixes:27a49ed17e224(gpio: arizona: Add support for GPIOs that)
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Liang <zhengliang6@huawei.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip may have dependencies from pinmux and so got deferred. Now it
will print error message every time -EPROBE_DEFER is returned which is
unnecessary:
"gpiochip_add_data_with_key: GPIOs 0..31 (gpio-0-31) failed to register, -517"
Hence, do suppress error message for -EPROBE_DEFER case.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by explicitly adding a fallthrough pseudo-keyword to indicate
that the code is intended to fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The gpiochip_add_data() may return -EPROBE_DEFER which is not handled
properly by TI GPIO driver and causes unnecessary boot log messages.
Hence, add proper deferred probe handling with new dev_err_probe() API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
There is no matching spi_get_drvdata() call in the driver, so there is no
need to do spi_set_drvdata(). This looks like it probably was copied from a
driver that used both spi_set_drvdata() & spi_get_drvdata().
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In dwapb_get_reset(), if devm_reset_control_get_optional_shared() fails,
an error message is printed even if the failure is the benign
EPROBE_DEFER error due to the reset controller not yet being
initialized. Use dev_err_probe() to handle
devm_reset_control_get_optional_shared() errors to avoid unnecessarilly
printing an error message for the deferred probe error.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We can simplify the error path in probe() and drop remove() entirely if
we provide a devm action for freeing the device ID.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We can simplify the code in gpio-exar by using regmap. This allows us to
drop the mutex (regmap provides its own locking) and we can also reuse
regmap's bit operations instead of implementing our own update function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Provide and use helpers for calculating the register address and bit
offset instead of hand coding it in every function.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's more elegant to use a helper local variable to store the address
of the underlying struct device than to dereference pdev everywhere. It
also has the benefit of avoiding unnecessary line breaks.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need to specify any ranges when allocating IDs so we can switch
to ida_alloc() and ida_free() instead of the ida_simple_ counterparts.
ida_simple_get(ida, 0, 0, gfp) is equivalent to
ida_alloc_range(ida, 0, UINT_MAX, gfp) which is equivalent to
ida_alloc(ida, gfp). Note: IDR will never actually allocate an ID
larger than INT_MAX.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This driver uses IDA APIs but doesn't include the relevant header. This
fixes it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
It's customary to have a newline between the copyright header and the
includes. Add one to gpio-exar.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use regmap accessors directly for register manipulation - removing one
layer of abstraction.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We can get hwirq number of the gpio by its irq_data->hwirq so that we don't
need to add more macros for different platforms. This patch is tested in
SiFive Unleashed board and SiFive Unmatched board.
Signed-off-by: Greentime Hu <greentime.hu@sifive.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since 5.10-rc1 i.MX is a devicetree-only platform, so simplify the code
by removing the unused non-DT support.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201117105917.27591-1-festevam@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In two different instances the return value of "of_property_read_u32"
API was neither captured nor checked.
Fixed it by capturing the return value and then checking for any error.
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Addresses-Coverity: "check_return"
Link: https://lore.kernel.org/r/1605201148-4508-9-git-send-email-srinivas.neeli@xilinx.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We may use BIT() macro to increase readability in
acpi_gpio_adr_space_handler().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
As specified by ACPI the pin index is 16-bit unsigned integer.
Define the variable, which holds it, accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that we are using similar code excerpts for ACPI OpRegion
and event handling. Deduplicate those excerpts by extracting a new
acpi_request_own_gpiod() helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GpioInt() implies input configuration of the pin. Add this to
the acpi_gpio_to_gpiod_flags() and make usable for GpioInt().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GpioIo() resources don't contain an initial value for the output pin.
Therefore instead of deducting its value solely based on bias field
we should deduce that value from the polarity and the bias fields.
Typical scenario is, when pin is defined in the table and its polarity,
specified in _DSD or via platform code, is defined as active low,
in the following call chain:
-> acpi_populate_gpio_lookup()
-> acpi_gpio_to_gpiod_flags()
it will return GPIOD_OUT_HIGH if bias is set no matter if polarity
is GPIO_ACTIVE_LOW, so it will return the current level instead of
the logical level.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Vasile-Laurentiu Stanimir <vasile-laurentiu.stanimir@windriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move acpi_gpio_to_gpiod_flags() upper in the code to allow further refactoring.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Mika noticed that some code is run under mutex when it doesn't require
the lock, like an error code assignment.
Move non-critical code outside of critical section.
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We didn't take into account the debounce settings supplied by ACPI.
This change is targeting the mentioned gap.
Reported-by: Coiby Xu <coiby.xu@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Use named item instead of plain integer for enum gpiod_flags
to make it clear that even 0 has its own meaning.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases the GpioInt() resource is coming with bias settings
which may affect system functioning. Respect bias settings for
GpioInt() resource by calling acpi_gpio_update_gpiod_*flags() API
in acpi_dev_gpio_irq_get().
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In some cases we would like to have debounce setter which doesn't fail
when a feature is not supported by a controller.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
This function is useful for internal use in the GPIO library.
There will be new user coming, prepare a helper for the new comer
and the existing ones.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Move bias related code from gpio_set_config() to gpio_set_bias().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In the future we will need to have a separate function
that takes an arbitrary argument value.
Extract gpio_set_config_with_argument() for that purpose.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Instead of open coded macro use, call pinconf_to_config_packed().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It's no difference in the functionality, but after the change the code
is less error prone to various checkers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace unsigned by unsigned int in GPIO library code.
Note, legacy API left untouched.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
If all we want to manage is a single pointer, there's no need to
manually allocate and add a new devres. We can simply use
devm_add_action_or_reset() and shrink the code by a good bit.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
- fix missing conversion to gpiolib irqchip in gpio-dwapb
- fix bank properties for ast2600 variant in gpio-aspeed
- make sysfs work again when the character device is disabled
- fix interrupt handling in gpio-pcie-idio-24
-----BEGIN PGP SIGNATURE-----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=dR2J
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.10-rc3
- fix missing conversion to gpiolib irqchip in gpio-dwapb
- fix bank properties for ast2600 variant in gpio-aspeed
- make sysfs work again when the character device is disabled
- fix interrupt handling in gpio-pcie-idio-24
Use raw_spinlock in order to fix spurious messages about invalid context
when spinlock debugging is enabled. This happens because there is a legit
nested raw_spinlock->spinlock locking usage within IRQ-related code. IRQ
core uses raw spinlock and then Tegra GPIO driver uses a nested spinlock.
The debug code can't recognize and handle this case, hence we need to use
raw spinlock in the GPIO driver.
[ BUG: Invalid wait context ]
...
(dump_stack) from (__lock_acquire)
(__lock_acquire) from (lock_acquire)
(lock_acquire) from (_raw_spin_lock_irqsave)
(_raw_spin_lock_irqsave) from (tegra_gpio_irq_set_type)
(tegra_gpio_irq_set_type) from (__irq_set_trigger)
(__irq_set_trigger) from (__setup_irq)
(__setup_irq) from (request_threaded_irq)
(request_threaded_irq) from (devm_request_threaded_irq)
(devm_request_threaded_irq) from (elants_i2c_probe)
(elants_i2c_probe) from (i2c_device_probe)
...
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add lockdep class in order to fix debug warnings that are coming from a
legit nested use of irq_set_irq_wake() by the Tegra GPIO driver.
WARNING: possible recursive locking detected
...
(irq_set_irq_wake) from (tegra_gpio_irq_set_wake)
(tegra_gpio_irq_set_wake) from (irq_set_irq_wake)
(irq_set_irq_wake) from (brcmf_sdiod_intr_register [brcmfmac])
...
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reported-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This enables the PEX8311 internal PCI wire interrupt and the PEX8311
local interrupt input so the local interrupts are forwarded to the PCI.
Fixes: 5855620466 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This fixes the COS Enable Register value for enabling/disabling the
corresponding IRQs bank.
Fixes: 5855620466 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix the bitwise operation to remove only the corresponding bit from the
mask.
Fixes: 5855620466 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family")
Cc: stable@vger.kernel.org
Signed-off-by: Arnaud de Turckheim <quarium@gmail.com>
Reviewed-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In gpiochip_setup_dev() the call to gpiolib_cdev_register() indirectly
calls device_add(). This is still required for the sysfs even when
CONFIG_GPIO_CDEV is not selected in the build.
Replace the stubbed functions in gpiolib-cdev.h with macros in gpiolib.c
that perform the required device_add() and device_del() when
CONFIG_GPIO_CDEV is not selected.
Fixes: d143493c01 (gpiolib: make cdev a build option)
Reported-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Tested-by: Nicolas Schichan <nschichan@freebox.fr>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for getting the state of multiple pins using a minimum of
register reads.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reuse gpio_rcar_info inside gpio_rcar_priv instead of duplicating the
individual members, so gpio_rcar_parse_dt() can copy them in one go.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Improve readability by aligning the offsets in the register definitions.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since commit 43c54ecade ("gpio: move the subdriver data pointer
into gpio_device") changed gpiochip_get_data() to an out-of-line
function, it is now worthwhile to avoid multiple calls in a row by
caching its return value in a local variable.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add GPIO_V2_LINE_FLAG_EDGE_BOTH macro and use it in edge_irq_thread() to
improve readability of edge handling cases.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Address code indentation warning messages by checkpatch script. Combine
split function parameters on one line. This also resolves the "use tabs
instead of space" warning by checkpatch script.
Signed-off-by: Deepak R Varma <mh12gx2825@gmail.com>
Link: https://lore.kernel.org/r/20201013190212.GA85788@ubuntu204
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allow the mockup driver to be probed via the device tree without any
module parameters, allowing it to be used to configure and test higher
level drivers like the leds-gpio driver and corresponding userspace
before actual hardware is available.
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
This reverts commit 579ced8fdb.
Turns out I was overly optimistic about cpu_pm blocking idle being a
solution for handling edge interrupts. While it helps in preventing
entering idle states that potentially lose context, we can still get
an edge interrupt triggering while entering idle. So we need to also
add back the workaround for seeing if there are any pending edge
interrupts when waking up.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Keerthy <j-keerthy@ti.com>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Tero Kristo <t-kristo@ti.com>
Link: https://lore.kernel.org/r/20201028060556.56038-1-tony@atomide.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We actually handle the gpio_irq_chip set-up properly
now despite what the comment says. Also assign this
pointer along with the rest of the gpio_irq_chip
setup code.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201019134429.65563-1-linus.walleij@linaro.org
Now that all gpiolib irqchip users have been over to use
the irqchip template, we can finally retire the old code
path and leave just one way in to the irqchip: set up the
template when registering the gpio_chip. For a while
we had two code paths for this which was a bit confusing.
This brings this work to a conclusion, there is now one
way of doing this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Link: https://lore.kernel.org/r/20201019134046.65101-1-linus.walleij@linaro.org
Use the new compat_need_64bit_alignment_fixup() helper to avoid
ugly ifdeffery in IOCTL compatibility code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kent Gibson <warthog618@gmail.com>
Depends-on: 527c412519 ("compat: add a compat_need_64bit_alignment_fixup() helper")
Link: https://lore.kernel.org/r/20201014103315.82662-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
First of all, bias has a special type as being a part of enum pin_config_param.
Second, 0 is also defined bias which is equivalent to BUS_HOLD.
Taking into account above, change type of bias variable and refactor
gpio_set_bias() in a way that it doesn't use BUS_HOLD as a place holder.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201009184359.16427-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_T is mapped to the most significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_T is input only. All
the other bits need to be 1 because GPIO_Q/R/S support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Commit 0ea683931a ("gpio: dwapb: Convert driver to using the
GPIO-lib-based IRQ-chip") missed the case in dwapb_irq_set_wake().
Without this fix, probing the dwapb gpio driver will hit a error:
"address between user and kernel address ranges" on a Ampere armv8a
server and cause a panic.
Fixes: 0ea683931a ("gpio: dwapb: Convert driver to using the GPIO-lib-based IRQ-chip")
Signed-off-by: Jia He <justin.he@arm.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
For better maintenance and micro optimization split error path
in the gpiod_request_commit().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Half of the code in the GPIO library is written in an expectation that
any non-zero value returned from the ->request() callback is an error code,
while some code checks only for negative values.
Unify expectations about ->request() returned value to be non-zero
for an error and 0 for the success.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use named item instead of plain integer for enum gpiod_flags
to make it clear that even 0 has its own meaning.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The line.eflags field is shared so document this fact and highlight it
throughout using READ_ONCE() and WRITE_ONCE() accessors.
Also use a local copy of the eflags in edge_irq_thread() to ensure
consistent control flow even if eflags changes. This is only a defensive
measure as edge_irq_thread() is currently disabled when the eflags are
changed.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Several places in the code are using same idiom, i.e.
IS_ERR(desc) && PTR_ERR(desc) == -ENOENT
which meaning is GPIO description is not found.
For better readability extract gpiod_not_found() helper and use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- The big core change is the updated (v2) userspace character
device API. This corrects badly designed 64-bit alignment around
the line events. We also add the debounce request feature.
This echoes the often quotes passage from Frederick Brooks
"The mythical man-month" to always throw one away, which we
have seen before in things such as V4L2. So we put in a new
one and deprecate and obsolete the old one.
- All example tools in tools/gpio/* are migrated to the new API
to set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in
device properties.
- Provide a generic library function kfree_strarray() that can
be used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now
uses the IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial
code clean-up and now use more of the core kernel
inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized,
which makes modularized GKI Android kernels happy.
-----BEGIN PGP SIGNATURE-----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=8CE2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This time very little driver changes but lots of core changes.
We have some interesting cooperative work for ARM and Intel alike,
making the GPIO subsystem more and more suitable for industrial
systems and the like, in addition to the in-kernel users.
We touch driver core (device properties) and lib/* by adding one
simple string array free function, these are authored by Andy
Shevchenko who is a well known and recognized core helpers maintainers
so this should be fine.
We also see some Android GKI-related modularization in the MXC
drivers.
Core changes:
- The big core change is the updated (v2) userspace character device
API.
This corrects badly designed 64-bit alignment around the line
events. We also add the debounce request feature. This echoes the
often quotes passage from Frederick Brooks "The mythical man-month"
to always throw one away, which we have seen before in things such
as V4L2. So we put in a new one and deprecate and obsolete the old
one.
- All example tools in tools/gpio/* are migrated to the new API to
set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in device
properties.
- Provide a generic library function kfree_strarray() that can be
used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now uses the
IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial code
clean-up and now use more of the core kernel inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized, which
makes modularized GKI Android kernels happy"
* tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpiolib: Update header block in gpiolib-cdev.h
gpiolib: cdev: switch from kstrdup() to kstrndup()
docs: gpio: add a new document to its index.rst
gpio: pca953x: Add support for the NXP PCAL9554B/C
tools: gpio: add debounce support to gpio-event-mon
tools: gpio: add multi-line monitoring to gpio-event-mon
tools: gpio: port gpio-event-mon to v2 uAPI
tools: gpio: port gpio-hammer to v2 uAPI
tools: gpio: rename nlines to num_lines
tools: gpio: port gpio-watch to v2 uAPI
tools: gpio: port lsgpio to v2 uAPI
gpio: uapi: document uAPI v1 as deprecated
gpiolib: cdev: support setting debounce
gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL
gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL
gpiolib: cdev: support edge detection for uAPI v2
gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL
gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL
gpiolib: add build option for CDEV v1 ABI
gpiolib: make cdev a build option
...
Core:
- Allow trimming of interrupt hierarchy to support odd hardware setups
where only a subset of the interrupts requires the full hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI PRUSS,
Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----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=1ewL
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
Make the tegra186 GPIO driver resistent to variable depth
interrupt hierarchy, which we are about to introduce.
No functionnal change yet.
Signed-off-by: Marc Zyngier <maz@kernel.org>
The dev_t is defined in types.h while struct gpio_device forward declaration
is missed. Take into account above and update header block in gpiolib-cdev.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201005095622.73616-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use kstrndup() to copy line labels from the userspace provided char
array, rather than ensuring the char array contains a null terminator
and using kstrdup().
Note that the length provided to kstrndup() still assumes that the char
array does contain a null terminator, so the maximum string length is one
less than the array. This is consistent with the previous behaviour.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20201005070246.20927-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pca953x driver never checks the result of irq_find_mapping(),
which returns 0 when no mapping is found. When a spurious interrupt
is delivered (which can happen under obscure circumstances), the
kernel explodes as it still tries to handle the error code as
a real interrupt.
Handle this particular case and warn on spurious interrupts.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201005140217.1390851-1-maz@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that UML (arch/um) has no compat.h header defined and hence
can't compile a recently provided piece of code in GPIO library.
Disable compat ->read() code in UML case to avoid compilation errors.
While at it, use pattern which is already being used in the kernel elsewhere.
Fixes: 5ad284ab3a ("gpiolib: Fix line event handling in syscall compatible mode")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201005131044.87276-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the
Spreadtrum driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode
for the character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for
bit manipulation in the PCA953x driver.
-----BEGIN PGP SIGNATURE-----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=295T
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some late GPIO fixes for the v5.9 series:
- Fix compiler warnings on the OMAP when PM is disabled
- Clear the interrupt when setting edge sensitivity on the Spreadtrum
driver.
- Fix up spurious interrupts on the TC35894.
- Support threaded interrupts on the Siox controller.
- Fix resource leaks on the mockup driver.
- Fix line event handling in syscall compatible mode for the
character device.
- Fix an unitialized variable in the PCA953A driver.
- Fix access to all GPIO IRQs on the Aspeed AST2600.
- Fix line direction on the AMD FCH driver.
- Use the bitmap API instead of compiler intrinsics for bit
manipulation in the PCA953x driver"
* tag 'gpio-v5.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: Correctly initialize registers 6 and 7 for PCA957x
gpio: pca953x: Use bitmap API over implicit GCC extension
gpio: amd-fch: correct logic of GPIO_LINE_DIRECTION
gpio: aspeed: fix ast2600 bank properties
gpio/aspeed-sgpio: don't enable all interrupts by default
gpio/aspeed-sgpio: enable access to all 80 input & output sgpios
gpio: pca953x: Fix uninitialized pending variable
gpiolib: Fix line event handling in syscall compatible mode
gpio: mockup: fix resource leak in error path
gpio: siox: explicitly support only threaded irqs
gpio: tc35894: fix up tc35894 interrupt configuration
gpio: sprd: Clear interrupt when setting the type as edge
gpio: omap: Fix warnings if PM is disabled
When driver has been converted to the bitmap API the non-bitmap functions
started behaving differently on 32-bit BE architectures since the bytes in
two consequent unsigned longs are in different order in comparison to byte
array. Hence if the chip had had more than 32 lines the memset() call over
it would have not set up upper lines correctly.
Although it's currently a theoretical case (no supported chips of this type
has 32+ lines), it's better to provide a clean code to avoid people thinking
this is okay and potentially producing not fully working things.
Fixes: 35d13d9489 ("gpio: pca953x: convert to use bitmap API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930142013.59247-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In IRQ handler we have to clear bitmap before use. Currently
the GCC extension has been used for that. For sake of the consistency
switch to bitmap API. As expected bloat-o-meter shows no difference
in the object size.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930142013.59247-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NXP PCAL9554B is a variant of the PCA953x GPIO expander,
with 8 GPIOs, latched interrupts and some advanced configuration
options. The "C" version only differs in I2C address.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200930092053.2114-2-mike.looijmans@topic.nl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for setting debounce on a line via the GPIO uAPI.
Where debounce is not supported by hardware, a software debounce is
provided.
The implementation of the software debouncer waits for the line to be
stable for the debounce period before determining if a level change,
and a corresponding edge event, has occurred. This provides maximum
protection against glitches, but also introduces a debounce_period
latency to edge events.
The software debouncer is integrated with the edge detection as it
utilises the line interrupt, and integration is simpler than getting
the two to interwork. Where software debounce AND edge detection is
required, the debouncer provides both.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for the GPIO_V2_LINE_SET_VALUES_IOCTL.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for GPIO_V2_LINE_SET_CONFIG_IOCTL, the uAPI v2
line set config ioctl.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for edge detection to lines requested using
GPIO_V2_GET_LINE_IOCTL.
The edge_detector implementation is based on the v1 lineevent
implementation. Unlike the v1 implementation, an overflow of the event
buffer results in discarding older events, rather than the most
recent, so the final event in a burst will correspond to the current
state of the line.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for GPIO_V2_GET_LINEINFO_IOCTL and
GPIO_V2_GET_LINEINFO_WATCH_IOCTL.
The core of this change is the event kfifo switching to contain
struct gpioline_info_changed_v2, instead of v1 as v2 is richer.
The two uAPI versions are mostly independent - other than where they both
provide line info changes via reads on the chip fd. As the info change
structs differ between v1 and v2, the infowatch implementation tracks which
version of the infowatch ioctl, either GPIO_GET_LINEINFO_WATCH_IOCTL or
GPIO_V2_GET_LINEINFO_WATCH_IOCTL, initiates the initial watch and returns
the corresponding info change struct to the read. The version supported
on that fd locks to that version on the first watch request, so subsequent
watches from that process must use the same uAPI version.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add support for requesting lines using the GPIO_V2_GET_LINE_IOCTL, and
returning their current values using GPIO_V2_LINE_GET_VALUES_IOCTL.
The struct linereq implementation is based on the v1 struct linehandle
implementation.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add a build option to allow the removal of the CDEV v1 ABI.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Make the gpiolib-cdev module a build option. This allows the CDEV
interface to be removed from the kernel to reduce kernel size in
applications where is it not required, and provides the parent for
other CDEV interface specific build options to follow.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Replace usage of strncpy() with strscpy() to remove -Wstringop-truncation
warnings.
The structures being populated are zeroed, to prevent stack leakage as
they are returned to userspace, so strscpy() performs the equivalent
function without the warnings.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Set the value of the line info offset in gpio_desc_to_lineinfo(), rather
than relying on it being passed in the info. This makes the function
behave as you would expect from the name - it generates the line info
corresponding to a given GPIO desc.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Let's move the code preparing the device properties into a separate
routine. This has the advantage of simplifying the error handling and
makes the indentation less deep.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
GPIO line names are currently created by the driver from the chip label.
We'll want to support custom formats for line names (for instance: to
name all lines the same) for user-space tests so create them in the
module init function and pass them to the driver using the standard
'gpio-line-names' property.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
While we do check the "chip-name" property in probe(), we never actually
use it. Let's pass the chip label to the driver using device properties
as we'll want to allow users to define their own once dynamically
created chips are supported.
The property is renamed to "chip-label" to not cause any confusion with
the actual chip name which is of the form: "gpiochipX".
If the "chip-label" property is missing, let's do what most devices in
drivers/gpio/ do and use dev_name().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The driver actually supports 4 properties but we only ever set up up to
three. This will change however in upcoming patches so increase the
number of really (as in: the number the property array can hold)
supported properties to 4.
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There's a return; at the end of a void function. This is not needed so
remove it.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
We don't need a custom logging helper. Let's use the standard pr_fmt()
macro which allows us to use all pr_*() routines with custom format.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Drop the definition for the driver name. Let's use KBUILD_MODNAME for
the log format and use the "gpio-mockup" value directly in the only
place where it's relevant: in the name of the device.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This module doesn't need gpio/consumer.h - it's a provider. It also
doesn't use any symbols from init.h so let's remove both includes.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Some Layerscape/QoriQ SoCs have input buffers which needs to be enabled
first. This was done in two different ways in the driver. Unify it.
This was tested on a LS1028A SoC.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Change config to tristate, add module device table, module author,
description and license to support module build for i.MX GPIO driver.
As this is a SoC GPIO module, it provides common functions for most
of the peripheral devices, such as GPIO pins control, secondary
interrupt controller for GPIO pins IRQ etc., without GPIO driver, most
of the peripheral devices will NOT work properly, so GPIO module is
similar with clock, pinctrl driver that should be loaded ONCE and
never unloaded.
Since MXC GPIO driver needs to have init function to register syscore
ops once, here still use subsys_initcall(), NOT module_platform_driver().
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1600320829-1453-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The original commit appears to have the logic reversed in
amd_fch_gpio_get_direction. Also confirmed by observing the value of
"direction" in the sys tree.
Signed-off-by: Ed Wildgoose <lists@wildgooses.com>
Fixes: e09d168f13 ("gpio: AMD G-Series PCH gpio driver")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
GPIO_U is mapped to the least significant byte of input/output mask, and
the byte in "output" mask should be 0 because GPIO_U is input only. All
the other bits need to be 1 because GPIO_V/W/X support both input and
output modes.
Similarly, GPIO_Y/Z are mapped to the 2 least significant bytes, and the
according bits need to be 1 because GPIO_Y/Z support both input and
output modes.
Fixes: ab4a85534c ("gpio: aspeed: Add in ast2600 details to Aspeed driver")
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the IRQ setup for the SGPIO driver enables all interrupts in
dual-edge trigger mode. Since the default handler is handle_bad_irq, any
state change on input GPIOs will trigger bad IRQ warnings.
This change applies sensible IRQ defaults: single-edge trigger, and all
IRQs disabled.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Currently, the aspeed-sgpio driver exposes up to 80 GPIO lines,
corresponding to the 80 status bits available in hardware. Each of these
lines can be configured as either an input or an output.
However, each of these GPIOs is actually an input *and* an output; we
actually have 80 inputs plus 80 outputs.
This change expands the maximum number of GPIOs to 160; the lower half
of this range are the input-only GPIOs, the upper half are the outputs.
We fix the GPIO directions to correspond to this mapping.
This also fixes a bug when setting GPIOs - we were reading from the
input register, making it impossible to set more than one output GPIO.
Signed-off-by: Jeremy Kerr <jk@codeconstruct.com.au>
Fixes: 7db47faae7 ("gpio: aspeed: Add SGPIO driver")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When pca953x_irq_pending returns false, the pending parameter won't
be set. But pca953x_irq_handler continues using this uninitialized
variable as pending irqs and will cause problem.
Fix the issue by initializing pending to 0.
Fixes: 064c73afe7 ("gpio: pca953x: Synchronize interrupt handler properly")
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- automatically drive GPHY leds in gpio-stp-xway
- refactor ->{get, set}_multiple() in gpio-aggregator
- add support for a new model in rcar-gpio DT bindings
- simplify several GPIO drivers with dev_err_probe()
- disable Direct KBD interrupts in gpio-tc35894
- use DEFINE_SEQ_ATTRIBUTE() in GPIO chardev to shrink code
- switch to using a simpler IDA API in gpiolib
- make devprop_gpiochip_set_names() more generic by using device properties
instead of using fwnode helpers
-----BEGIN PGP SIGNATURE-----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=RbA2
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.10-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.10 - part 1
- automatically drive GPHY leds in gpio-stp-xway
- refactor ->{get, set}_multiple() in gpio-aggregator
- add support for a new model in rcar-gpio DT bindings
- simplify several GPIO drivers with dev_err_probe()
- disable Direct KBD interrupts in gpio-tc35894
- use DEFINE_SEQ_ATTRIBUTE() in GPIO chardev to shrink code
- switch to using a simpler IDA API in gpiolib
- make devprop_gpiochip_set_names() more generic by using device properties
instead of using fwnode helpers
Add support for the GPIO controller of the sl28 board management
controller. This driver is part of a multi-function device.
A controller has 8 lines. There are three different flavors:
full-featured GPIO with interrupt support, input-only and output-only.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
It's possible for a GPIO chip to not have a parent device (whose
properties we inspect for 'gpio-line-names'). In this case we should
simply return from devprop_gpiochip_set_names(). Add an appropriate
check for this use-case.
Fixes: 7cba1a4d5e ("gpiolib: generalize devprop_gpiochip_set_names() for device properties")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Anders Roxell <anders.roxell@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The introduced line event handling ABI in the commit
61f922db72 ("gpio: userspace ABI for reading GPIO line events")
missed the fact that 64-bit kernel may serve for 32-bit applications.
In such case the very first check in the lineevent_read() will fail
due to alignment differences.
To workaround this introduce lineevent_get_size() helper which returns actual
size of the structure in user space.
Fixes: 61f922db72 ("gpio: userspace ABI for reading GPIO line events")
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Now that devprop_gpiochip_set_names() is only used in a single place
inside drivers/gpio/gpiolib.c, there's no need anymore for it to be
exported or to even live in its own source file. Pull this function into
the core source file for gpiolib.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
devprop_gpiochip_set_names() is overly complicated with taking the
fwnode argument (which requires using dev_fwnode() & of_fwnode_handle()
in ACPI and OF GPIO code respectively). Let's just switch to using the
generic device properties.
This allows us to pull the code setting line names directly into
gpiochip_add_data_with_key() instead of handling it separately for
ACPI and OF.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We don't need to specify any ranges when allocating IDs so we can switch
to ida_alloc() and ida_free() instead of the ida_simple_ counterparts.
ida_simple_get(ida, 0, 0, gfp) is equivalent to
ida_alloc_range(ida, 0, UINT_MAX, gfp) which is equivalent to
ida_alloc(ida, gfp). Note: IDR will never actually allocate an ID
larger than INT_MAX.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Use DEFINE_SEQ_ATTRIBUTE macro to simplify the code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If the module init function fails after creating the debugs directory,
it's never removed. Add proper cleanup calls to avoid this resource
leak.
Fixes: 9202ba2397 ("gpio: mockup: implement event injecting over debugfs")
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The gpio-siox driver uses handle_nested_irq() to implement its
interrupt support. This is only capable of handling threaded irq
actions. For a hardirq action it triggers a NULL pointer oops.
(It calls action->thread_fn which is NULL then.)
Prevent registration of a hardirq action by setting
gpio_irq_chip::threaded to true.
Cc: u.kleine-koenig@pengutronix.de
Fixes: be8c8facc7 ("gpio: new driver to work with a 8x12 siox")
Cc: stable@vger.kernel.org
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
On tc35894, have to disable direct keypad interrupts to make
it as general purpose interrupts functionality work.
if not, after chip reset, IRQST(0x91) will always 0x20,
IRQN always low level, can't be clear.
Configure DIRECTx to enable general purpose gpio mode,
else read GPIOMISx register always zero in irq routine.
verified on tc35894, need more test on other tc3589x.
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The offset of regmap is incorrect, j * 8 is move to the
wrong register.
for example:
asume i = 0, j = 1. we want to set KPY5 as interrupt
falling edge mode, regmap[0][1] should be TC3589x_GPIOIBE1 0xcd
but, regmap[i] + j * 8 = TC3589x_GPIOIBE0 + 8 ,point to 0xd4,
this is TC3589x_GPIOIE2 not TC3589x_GPIOIBE1.
Fixes: d88b25be35 ("gpio: Add TC35892 GPIO driver")
Cc: Cc: stable@vger.kernel.org
Signed-off-by: dillon min <dillon.minfei@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The raw interrupt status of GPIO maybe set before the interrupt is enabled,
which would trigger the interrupt event once enabled it from user side.
This is the case for edge interrupts only. Adding a clear operation when
setting interrupt type can avoid that.
There're a few considerations for the solution:
1) This issue is for edge interrupt only; The interrupts requested by users
are IRQ_TYPE_LEVEL_HIGH as default, so clearing interrupt when request
is useless.
2) The interrupt type can be set to edge when request and following up
with clearing it though, but the problem is still there once users set
the interrupt type to level trggier.
3) We can add a clear operation after each time of setting interrupt
enable bit, but it is redundant for level trigger interrupt.
Therefore, the solution is this patch seems the best for now.
Fixes: 9a3821c2bb ("gpio: Add GPIO driver for Spreadtrum SC9860 platform")
Signed-off-by: Taiping Lai <taiping.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and also it prints the error value.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since the resource managed version of gpiochip_add_data() will handle the
GPIO-chip data automated cleanup we can freely remove the DW APB GPIO
driver code responsible for that. After doing so the DW APB GPIO driver
removal callback can be also fully discarded since there is nothing left
to be done for it. All the cleanups are now performed by means of the
device managed framework.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-11-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The kernel clock framework provides the resource managed version of
the clk_bulk_get() method. The only thing which needs to be also automated
is the clocks disable/unprepare procedure executed on the device removal.
It can be implemented by means of the custom action definition. After that
the clocks acquisition and release will be purely managed by the device
resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-10-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The reset control interface provides the resource managed version of
the reset_control_get() method. The only thing which needs to be also
automated is the reset lane assertion on the device removal. It can be
implemented by means of the custom action definition. After that the reset
control will be purely managed by the device resources interface.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-9-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need
in calling the methods acpi_gpiochip_{request,free}_interrupts() here.
They will be called from gpiochip_add_irqchip()/gpiochip_irqchip_remove()
anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-8-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since GPIOlib-based IRQ-chip interface is now utilized there is no need in
setting up a custom GPIO-to-IRQ mapping method. GPIO-lib defines the
standard mapping method - gpiochip_to_irq(), which will be used anyway no
matter whether the custom to_irq callback is specified or not.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO-lib provides a ready-to-use interface to initialize an IRQ-chip on
top of a GPIO chip. It's better from maintainability and readability
point of view to use one instead of supporting a hand-written Generic
IRQ-chip-based implementation. Moreover the new implementation won't
cause much functional overhead but will provide a cleaner driver code.
All of that makes the DW APB GPIO driver conversion pretty much justified
especially seeing a tendency of the other GPIO drivers getting converted
too.
Here is what we do in the framework of this commit to convert the driver
to using the GPIO-lib-based IRQ-chip interface:
1) IRQ ack, mask and unmask callbacks are locally defined instead of
using the Generic IRQ-chip ones.
2) An irq_chip structure instance is embedded into the dwapb_gpio
private data. Note we can't have a static instance of that structure since
GPIO-lib will add some hooks into it by calling gpiochip_set_irq_hooks().
A warning about that would have been printed by the GPIO-lib code if we
used a single irq_chip structure instance for multiple DW APB GPIO
controllers.
3) Initialize the gpio_irq_chip structure embedded into the gpio_chip
descriptor. By default there is no IRQ enabled so any event raised will be
handled by the handle_bad_irq() IRQ flow handler. If DW APB GPIO IP-core
is synthesized to have non-shared reference IRQ-lines, then as before the
hierarchical and cascaded cases are distinguished by checking how many
parental IRQs are defined. (Note irq_set_chained_handler_and_data() won't
initialize IRQs, which descriptors couldn't be found.) If DW APB GPIO IP
is used on a platform with shared IRQ line, then we simply won't let the
GPIO-lib to initialize the parental IRQs, but will handle them locally in
the driver.
4) Discard linear IRQ-domain and Generic IRQ-chip initialization, since
GPIO-lib IRQ-chip interface will create a new domain and accept a standard
IRQ-chip structure pointer based on the setting we provided in the
gpio_irq_chip structure.
5) Manually select a proper IRQ flow handler directly in the
irq_set_type() callback by calling irq_set_handler_locked() method, since
an ordinary (not Generic) irq_chip descriptor is now utilized. Note this
shalln't give any regression
6) Alter CONFIG_GPIO_DWAPB kernel config to select
CONFIG_GPIOLIB_IRQCHIP instead of CONFIG_GENERIC_IRQ_CHIP.
Note neither 4) nor 5) shall cause a regression of commit 6a2f4b7dad
("gpio: dwapb: use a second irq chip"), since the later isn't properly
used here anyway.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add a new macro DWAPB_MAX_GPIOS which defines the maximum possible number
of GPIO lines corresponding to the maximum DW APB GPIO controller port
width. Use the new macro instead of number literal 32 where it's
applicable.
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For better readability let's group all the IRQ handlers in a single place
of the driver instead of having them scatter around all over the file.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Indeed generic GPIO DT-schema implies that number of GPIOs should be
described by the "ngpios" property located under a GPIO-provider DT node.
In that case it's redundant to have a vendor-specific "snps,nr-gpios"
property describing the same setting. Moreover it might be errors prone.
Since commit 93d2e4322a ("of: platform: Batch fwnode parsing when adding
all top level devices") the fwnode parsing is resumed after the vast
majority of the platform devices are added. Implicitly that commit
activates re-parsing of the whole device tree GPIOs-phandle properties
detected having "-gpio/-gpios" suffixes. Since the vendor-specific number
of GPIOs property is defined with "-gpios" suffix, then of_link_property()
will consider it as a suffix-property with "#gpio-cells" structure, which
obviously it doesn't have. As a result for two DW APB GPIO controllers
we'll have the next errors printed.
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
OF: /bus@1f059000/gpio@1f044000/gpio-port@0: could not find phandle
OF: /bus@1f059000/gpio@1f045000/gpio-port@0: could not get #gpio-cells for /opp-table
See, the kernel fwnode parsing procedure even tried to resolve the phandle
ID, which it thought was the opp-table DT-node, while in fact it was just
a number "32". What would happen if that magic number actually referred to
a GPIO DT-node with "#gpio-cells" property defined?..
In order to fix the problem let's mark the "snps,nr-gpios" property as
deprecated and add the generic "ngpios" property support with the same
purpose as the deprecated one. That and the errors log above shall
motivate the platform developer to convert the DW APB GPIO DT-nodes to
using the standard number of GPIOs property.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200730152808.2955-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix warnings for omap_gpio_resume and omap_gpio_suspend
defined but not used when PM is disabled as noticed when
doing make randconfig builds.
Fixes: f02a03985d ("gpio: omap: Add missing PM ops for suspend")
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sparse can't see locking scheme used in ->get_multiple() and
->set_multiple() callbacks.
CHECK .../drivers/gpio/gpio-aggregator.c
.../spinlock.h:409:9: warning: context imbalance in 'gpio_fwd_get_multiple' - unexpected unlock
.../spinlock.h:409:9: warning: context imbalance in 'gpio_fwd_set_multiple' - unexpected unlock
Refactor them to have better readability and make Sparse happy.
Code size impact is +52 bytes with arm-linux-gnueabihf-gcc 7.5.0.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Ar10 (xr300) has 3 and grx390 (xrx330) has 4 built-in GPHY. PHY LEDs are
connected via STP. STP is a peripheral controller used to drive external
shift register cascades. The hardware is able to allow the GPHY to drive
some GPIO of the cascade automatically.This patch allows for this on ar10
and grx390.
Tested on D-Link DWR-966 with OpenWRT.
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Core changes:
- Introduce the for_each_requested_gpio() macro to help in
dependent code all over the place. Also patch a few locations
to use it while we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then
make a set of refactorings and improvements to this code.
We are setting the stage to revamp the userspace API a bit
in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other
drivers requesting their own IRQ while using the core
GPIO IRQ helpers to pass the GPIO irq chip as a template
instead of calling the explicit set-up functions. Next merge
window we may retire the old code altogether.
-----BEGIN PGP SIGNATURE-----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=OSvz
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.9 kernel cycle.
There is nothing too exciting in it, but a new macro that fixes a
build failure on a minor ARM32 platform that appeared yesterday is
part of it so we better merge it.
Core changes:
- Introduce the for_each_requested_gpio() macro to help in dependent
code all over the place. Also patch a few locations to use it while
we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then make a
set of refactorings and improvements to this code. We are setting
the stage to revamp the userspace API a bit in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other drivers
requesting their own IRQ while using the core GPIO IRQ helpers to
pass the GPIO irq chip as a template instead of calling the
explicit set-up functions. Next merge window we may retire the old
code altogether"
* tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (97 commits)
gpio: wcove: Request IRQ after all initialisation done
gpio: crystalcove: Free IRQ on error path
gpio: pca953x: Request IRQ after all initialisation done
gpio: don't use same lockdep class for all devm_gpiochip_add_data users
gpio: max732x: Use irqchip template
gpio: stmpe: Move chip registration
gpio: rcar: Use irqchip template
gpio: regmap: fix type clash
gpio: Correct kernel-doc inconsistency
gpio: pci-idio-16: Use irqchip template
gpio: pcie-idio-24: Use irqchip template
gpio: 104-idio-16: Use irqchip template
gpio: 104-idi-48: Use irqchip template
gpio: 104-dio-48e: Use irqchip template
gpio: ws16c48: Use irqchip template
gpio: omap: improve coding style for pin config flags
gpio: dln2: Use irqchip template
gpio: sch: Add a blank line between declaration and code
gpio: sch: changed every 'unsigned' to 'unsigned int'
gpio: ich: changed every 'unsigned' to 'unsigned int'
...
There is logically better to request IRQ when we initialise all structures.
Align the driver with the rest on the same matter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that all, but request_irq(), calls in the driver are device managed.
In unlikely case of devm_gpiochip_add_data() failure the IRQ left requested.
Free IRQ on error path by switching to devm_request_threaded_irq() API.
Byproduct of this change is a drop of ->remove() callback completely.
Fixes: 945e72db36 ("gpio: crystalcove: Use irqchip template")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is logically better to request IRQ when we initialise all structures.
Align the driver with the rest on the same matter.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200728125504.27786-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit 959bc7b22b ("gpio: Automatically add lockdep keys") documents
in its commits message its intention to "create a unique class key for
each driver".
It does so by having gpiochip_add_data add in-place the definition of
two static lockdep classes for LOCKDEP use. That way, every caller of
the macro adds their gpiochip with unique lockdep classes.
There are many indirect callers of gpiochip_add_data, however, via
use of devm_gpiochip_add_data. devm_gpiochip_add_data has external
linkage and all its users will share the same lockdep classes, which
probably is not intended.
Fix this by replicating the gpio_chip_add_data statics-in-macro for
the devm_ version as well.
Fixes: 959bc7b22b ("gpio: Automatically add lockdep keys")
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200731123835.8003-1-a.fatoum@pengutronix.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20200726221259.133536-1-linus.walleij@linaro.org
Make sure to register the GPIO chip after requesting the
interrupt and setting up the IRQ members of the irqchip.
Fixes: 9745079609 ("gpio: stmpe: Use irqchip template")
Reported-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Link: https://lore.kernel.org/r/20200728072706.348725-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Biju Das <biju.das@bp.renesas.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200722113141.243163-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722110649.202223-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722110027.192782-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722105517.186137-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722104820.174654-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722103915.162156-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Also move the IRQ initialization to the special .init_hw()
callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Link: https://lore.kernel.org/r/20200722101938.151265-1-linus.walleij@linaro.org
Change the handling of pin config flags from if/else to switch
statement to make the code more readable and cleaner.
Suggested-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/20200722120755.230741-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add(). The irqchip is
instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Daniel Baluta <daniel.baluta@gmail.com>
Cc: Octavian Purdila <octavian.purdila@nxp.com>
Link: https://lore.kernel.org/r/20200722073426.38890-1-linus.walleij@linaro.org
* Move GPIO PMIC drivers to use IRQ chip template
* Introduce for_each_requested_gpio() and convert existing users
* Replace unsigned by unsigned int in few drivers
* Fix an issue in kernel doc that validator complains about
* Move to verbose debug level the IRQ status message in gpio-pch
The following is an automated git shortlog grouped by driver:
ARM/orion/gpio:
- Make use of for_each_requested_gpio()
crystalcove:
- Use irqchip template
- changed every 'unsigned' to 'unsigned int'
gpiolib:
- Introduce for_each_requested_gpio_in_range() macro
gpio-ml-ioh:
- Fix missing ':' in 'struct ioh_gpio_reg_data
ich:
- changed every 'unsigned' to 'unsigned int'
mvebu:
- Make use of for_each_requested_gpio()
pch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
- Move IRQ status message to verbose debug level
pinctrl:
- at91: Make use of for_each_requested_gpio()
sch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
wcove:
- Use irqchip template
xra1403:
- Make use of for_each_requested_gpio()
-----BEGIN PGP SIGNATURE-----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=txvs
-----END PGP SIGNATURE-----
Merge tag 'intel-gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into devel
intel-gpio for v5.9-1
* Move GPIO PMIC drivers to use IRQ chip template
* Introduce for_each_requested_gpio() and convert existing users
* Replace unsigned by unsigned int in few drivers
* Fix an issue in kernel doc that validator complains about
* Move to verbose debug level the IRQ status message in gpio-pch
The following is an automated git shortlog grouped by driver:
ARM/orion/gpio:
- Make use of for_each_requested_gpio()
crystalcove:
- Use irqchip template
- changed every 'unsigned' to 'unsigned int'
gpiolib:
- Introduce for_each_requested_gpio_in_range() macro
gpio-ml-ioh:
- Fix missing ':' in 'struct ioh_gpio_reg_data
ich:
- changed every 'unsigned' to 'unsigned int'
mvebu:
- Make use of for_each_requested_gpio()
pch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
- Move IRQ status message to verbose debug level
pinctrl:
- at91: Make use of for_each_requested_gpio()
sch:
- Add a blank line between declaration and code
- changed every 'unsigned' to 'unsigned int'
wcove:
- Use irqchip template
xra1403:
- Make use of for_each_requested_gpio()
Added a lined between a declaration and other statements according to the
kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Cc: Bin Gao <bin.gao@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This converts the PPC4xx SPI driver to use GPIO descriptors.
The driver is already just picking some GPIOs from the device
tree so the conversion is pretty straight forward. However
this driver is looking form a pure "gpios" property rather
than the standard binding "cs-gpios" so we need to add a new
exception to the gpiolib OF parser to allow this for this
driver's compatibles.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: https://lore.kernel.org/r/20200714072226.26071-1-linus.walleij@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Added a lined between a declaration and other statements according to the
kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Changed 'unsigned' to 'unsigned int'.
This makes the code more uniform, and compliant with the kernel coding style.
Signed-off-by: Abanoub Sameh <abanoubsameh@protonmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20200717144040.63253-1-linus.walleij@linaro.org
Modify omap_gpio_set_config() to handle pin config bias flags by calling
gpiochip_generic_config().
The pin group for the gpio line must have the corresponding pinconf
properties:
PIN_CONFIG_BIAS_PULL_UP requires "pinctrl-single,bias-pullup"
PIN_CONFIG_BIAS_PULL_DOWN requires "pinctrl-single,bias-pulldown"
This is necessary for pcs_pinconf_set() to find the requested bias
parameter in the PIN_MAP_TYPE_CONFIGS_GROUP pinctrl map.
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20200715213738.1640030-1-drew@beagleboard.org
Link: https://lore.kernel.org/r/20200717194043.1774643-1-drew@beagleboard.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Anders Darander <anders@chargestorm.se>
Cc: Roger Quadros <rogerq@ti.com>
Link: https://lore.kernel.org/r/20200717144835.68150-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Cc: Nikolaus Voss <nv@vosn.de>
Cc: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20200716150502.195821-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Roland Stigge <stigge@antcom.de>
Cc: Lars Poeschel <poeschel@lemonage.de>
Link: https://lore.kernel.org/r/20200716120318.127176-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Alexandre TORGUE <alexandre.torgue@st.com>
Link: https://lore.kernel.org/r/20200716100638.112451-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200716093459.76378-1-linus.walleij@linaro.org
Most other drivers fill out the gpio_irq_chip using a
struct gpio_irq_chip *girq helper variable for ease of
reading.
We also make a habit of explicitly assigning NULL and
zero to the parent IRQs when using ordinary IRQ handlers
in the driver, mostly for code readability and
maintenance.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Cc: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20200716092835.69176-1-linus.walleij@linaro.org
I noticed on Nexus 7 that after rebooting from downstream kernel to
upstream, the GPIO interrupt is triggering non-stop despite interrupts
being disabled for all of GPIOs. This happens because Nexus 7 uses a
soft-reboot, meaning that bootloader should take care of resetting
hardware, but the bootloader doesn't do it well. As a result, GPIO
interrupt may be left ON at a boot time. Let's mask all GPIO interrupts
at the driver's initialization time in order to resolve the issue.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-7-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change addresses one of the GPIO-core TODOs for the MAX77620 driver
which requires modern drivers to use the irqchip template. Instead of
using the GPIO's irqchip-helpers for creating the IRQ domain, the
gpio_irq_chip structure is now filled by the driver itself and then
gpiochip_add_data() takes care of instantiating the IRQ domain for us.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-6-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The platform_get_irq() returns a positive interrupt number on success and
negative error code on failure (zero shouldn't ever happen in practice, it
would produce a noisy warning). Hence let's return the error code directly
instead of overriding it with -ENODEV.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-5-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The gpiochip_add_data() takes care of setting the of_node to the parent's
device of_node, hence there is no need to do it manually in the driver's
code. This patch corrects the parent's device pointer and removes the
unnecessary setting of the of_node.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-4-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The requested interrupt is never released by the driver. Fix this by
using the resource-managed variant of request_threaded_irq().
Fixes: ab3dd9cc24 ("gpio: max77620: Fix interrupt handling")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Cc: <stable@vger.kernel.org> # 5.5+
Link: https://lore.kernel.org/r/20200709171203.12950-3-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The MAX77620_GPIO_NR enum value represents the total number of GPIOs,
let's use it instead of a raw value in order to improve the code's
readability a tad.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Link: https://lore.kernel.org/r/20200709171203.12950-2-digetx@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Consolidate the cleanup of lineevents, currently duplicated in
lineevent_create and lineevent_release, into a helper function
lineevent_free.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Consolidate the cleanup of linehandles, currently duplicated in
linehandle_create and linehandle_release, into a helper function
linehandle_free.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove recalculation of offset from desc, where desc itself was calculated
from offset.
There is no benefit from the desc -> hwgpio conversion in this context.
The only implicit benefit of the offset -> desc -> hwgpio is
the range check in the offset -> desc, but where desc is required you
still get that, and where desc isn't required it is simpler to perform
the range check directly.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Merge separate usage of test_bit/set_bit into test_and_set_bit to remove
the possibility of a race between the test and set.
Similarly test_bit and clear_bit.
In the existing code it is possible for two threads to race past the
test_bit and then set or clear the watch bit, and neither return EBUSY.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename priv to cdev to improve readability.
The name "priv" indicates that the object is pointed to by
file->private_data, not what the object is actually is.
As it is always used to point to a struct gpio_chardev_data, renaming
it to cdev is more appropriate.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Replace usage of atomic_notifier_call_chain with
blocking_notifier_call_chain as the notifier function,
lineinfo_changed_notify, calls gpio_desc_to_lineinfo,
which calls pinctrl_gpio_can_use_line, which can sleep.
The chain isn't being called from an atomic context so the
the blocking notifier is a suitable substitute.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Remove pointless decrement of variable, and associated comment.
While i is used subsequently, it is re-initialized so this decrement
serves no purpose.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename numdescs to num_descs to be more consistent with the naming of
other counters and improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Rename 'filep' and 'filp' to 'file' to be consistent with other use
and improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Refactor the mapping from handle flags to desc flags into a helper
function.
The assign_bit is overkill where it is replacing the set_bit cases, as is
rechecking bits known to be clear in some circumstances, but the DRY
simplification more than makes up for any performance degradation,
especially as this is not a hot path.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Make indentation consistent with other use to improve readability.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sort the includes of gpiolib-cdev.c to make it easier to identify if a
module is included and to avoid duplication.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move gpiolib-sysfs function declarations into their own header.
These functions are in gpiolib-sysfs.c, and are only required by gpiolib.c,
and so should be in a module header, not gpiolib.h.
This brings gpiolib-sysfs into line with gpiolib-cdev, and is another step
towards removing the sysfs inferface.
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Sparse cannot peer into other functions to see when and if locks are
acquired and released, thus it simply warns that a 'context imbalance'
is detected instead. Let's be kind to Sparse and let it know that
this behaviour is intentional.
drivers/gpio/gpio-mlxbf2.c:125:12: warning: context imbalance in 'mlxbf2_gpio_lock_acquire' - different lock contexts for basic block
drivers/gpio/gpio-mlxbf2.c:151:13: warning: context imbalance in 'mlxbf2_gpio_lock_release' - unexpected unlock
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Asmaa Mnebhi <asmaa@mellanox.com>
Cc: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-11-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
... as is the case when !CONFIG_ACPI.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-mlxbf2.c:312:36: warning: ‘mlxbf2_gpio_acpi_match’ defined but not used [-Wunused-const-variable=]
312 | static const struct acpi_device_id mlxbf2_gpio_acpi_match[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Asmaa Mnebhi <asmaa@mellanox.com>
Cc: Asmaa Mnebhi <Asmaa@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-10-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
... as is the case when !CONFIG_ACPI.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-mlxbf.c:130:36: warning: ‘mlxbf_gpio_acpi_match’ defined but not used [-Wunused-const-variable=]
130 | static const struct acpi_device_id mlxbf_gpio_acpi_match[] = {
| ^~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Shravan Kumar Ramani <sramani@mellanox.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-9-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kerneldoc expects struct properties to be documented using the syntax
'@.*: ', but no ':' has been provided in 'struct it87_gpio's
header. Add them to stop confusing kerneldoc.
Fixes the following W=1 warnings:
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'chip' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'lock' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'io_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'io_size' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'output_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'simple_base' not described in 'it87_gpio'
drivers/gpio/gpio-it87.c:69: warning: Function parameter or member 'simple_size' not described in 'it87_gpio'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: "Diego Elio Pettenò" <flameeyes@flameeyes.eu>
Link: https://lore.kernel.org/r/20200630133345.2232932-8-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kerneldoc expects struct properties to be documented using the syntax
'@.*: ', but no '@' has been provided in 'struct syscon_gpio_data's
header. Add them to stop confusing kerneldoc.
Fixes the following W=1 warnings:
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'compatible' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'flags' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'bit_count' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'dat_bit_offset' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'dir_bit_offset' not described in 'syscon_gpio_data'
drivers/gpio/gpio-syscon.c:48: warning: Function parameter or member 'set' not described in 'syscon_gpio_data'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Alexander Shiyan <shc_work@mail.ru>
Link: https://lore.kernel.org/r/20200630133345.2232932-7-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
No attempt has been made to provide proper descriptions for each of
the function arguments throughout the file. Simply demote all
kerneldoc headers to basic function headers.
Fixes the following W=1 kernel build warnings:
drivers/gpio/gpio-sama5d2-piobu.c:59: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_setup_pin'
drivers/gpio/gpio-sama5d2-piobu.c:59: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_setup_pin'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'mask' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:81: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_write_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:97: warning: Function parameter or member 'mask' not described in 'sama5d2_piobu_read_value'
drivers/gpio/gpio-sama5d2-piobu.c:116: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_get_direction'
drivers/gpio/gpio-sama5d2-piobu.c:116: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_get_direction'
drivers/gpio/gpio-sama5d2-piobu.c:131: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_direction_input'
drivers/gpio/gpio-sama5d2-piobu.c:131: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_direction_input'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:140: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_direction_output'
drivers/gpio/gpio-sama5d2-piobu.c:154: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_get'
drivers/gpio/gpio-sama5d2-piobu.c:154: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_get'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'chip' not described in 'sama5d2_piobu_set'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'pin' not described in 'sama5d2_piobu_set'
drivers/gpio/gpio-sama5d2-piobu.c:174: warning: Function parameter or member 'value' not described in 'sama5d2_piobu_set'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Andrei Stefanescu <andrei.stefanescu@microchip.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-6-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
A good attempt has been made to properly document 'struct
sprd_pmic_eic', but 'map' has been incorrectly described as
'regmap' since the driver's inception in 2018.
Fixes the following W=1 kernel build warning:
drivers/gpio/gpio-pmic-eic-sprd.c:65: warning: Function parameter or member 'map' not described in 'sprd_pmic_eic'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-5-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
'struct altera_gpio_chip's 'irq_chip' property is undocumented. So
add property description to the struct's kerneldoc header. Also
demote comment block which is clearly not in kerneldoc format.
Fixes the following W=1 warnings:
drivers/gpio/gpio-altera.c:34: warning: Function parameter or member 'irq_chip' not described in 'altera_gpio_chip'
drivers/gpio/gpio-altera.c:78: warning: Function parameter or member 'd' not described in 'altera_gpio_irq_set_type'
drivers/gpio/gpio-altera.c:78: warning: Function parameter or member 'type' not described in 'altera_gpio_irq_set_type'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Joyce Ooi <joyce.ooi@intel.com>
Cc: Tien Hock Loh <thloh@altera.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-3-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Descriptions for of_gpio_spi_cs_get_count()'s 2 arguments are
missing. Document both 'dev' and 'con_id'.
Fixes the following W=1 kernel build warnings:
drivers/gpio/gpiolib-of.c:36: warning: Function parameter or member 'dev' not described in 'of_gpio_spi_cs_get_count'
drivers/gpio/gpiolib-of.c:36: warning: Function parameter or member 'con_id' not described in 'of_gpio_spi_cs_get_count'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Link: https://lore.kernel.org/r/20200630133345.2232932-2-lee.jones@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Replace the custom code to parse GPIO offsets and/or GPIO offset ranges
by a call to bitmap_parselist(), and an iteration over the returned bit
mask.
This should have no impact on the format of the configuration parameters
written to the "new_device" virtual file in sysfs.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200701114212.8520-3-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In get_arg(), the variable start is pre-initialized, but overwritten
again in the first statement. Rework the assignment to not rely on
pre-initialization, to make the code easier to read.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200701114212.8520-2-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If one of the devices which share the same IRQ line doesn't care about
interrupt GPIO will spam the log with status equal to 0x00. Move IRQ
status message to verbose debug level (it still might be useful).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
- use kobj_to_dev() in sysfs interface
- kerneldoc and documentation fixes
- relax the interrupt flags in gpio-mpc8xxx
- support new model in gpio-pca953x
- remove a redundant check from gpio-max732x
- support a new platform in gpio-zynq (+ some minor fixes)
- don't depend on GPIOLIB when already inside the "if GPIOLIB" in Kconfig
- support PM ops for suspend in gpio-omap
- minor tweaks in gpiolib
-----BEGIN PGP SIGNATURE-----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=TwKk
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.9-part1' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio updates for v5.9
- use kobj_to_dev() in sysfs interface
- kerneldoc and documentation fixes
- relax the interrupt flags in gpio-mpc8xxx
- support new model in gpio-pca953x
- remove a redundant check from gpio-max732x
- support a new platform in gpio-zynq (+ some minor fixes)
- don't depend on GPIOLIB when already inside the "if GPIOLIB" in Kconfig
- support PM ops for suspend in gpio-omap
- minor tweaks in gpiolib
'struct ioh_gpio_reg_data's 'ien_reg' property is missing a ':'
which confuses the kerneldoc tooling/parsers/validators.
Replacing it squashes the following W=1 warning:
drivers/gpio/gpio-ml-ioh.c:63: warning: Function parameter or member 'ien_reg' not described in 'ioh_gpio_reg_data'
Cc: Andy Shevchenko <andy@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
bitmap_full() is a shortcut to find_first_zero_bit().
Thus, no need to call it twice.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
We've had the legacy platform code take care of suspend for us but
this no longer is the case when probed without legacy mode with
ti-sysc. We need to configure PM ops like standard Linux device
drivers do.
As we still have some SoCs booting also the legacy mode, we need to
add omap_gpio_suspend() and omap_gpio_resume(), and check for the
is_suspended flag to avoid legacy _od_suspend_noirq() calling them
on an already suspended GPIO instance.
Once we have no SoCs booting in legacy mode, we can just switch to
using the standard PM ops with pm_runtime_force_suspend() and
pm_runtime_force_resume().
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
- several fixes for gpio-pca953x
-----BEGIN PGP SIGNATURE-----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=Qg1z
-----END PGP SIGNATURE-----
Merge tag 'gpio-fixes-for-v5.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.8-rc3
- several fixes for gpio-pca953x
All config options for GPIO drivers are inside a big "if GPIOLIB ...
endif" block, so there is no reason for individual config options to
have expicit dependencies on GPIOLIB. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In case of probe is deferred do not print the errors.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add PMC gpio support.
Only bank 0,1, 3 and 4 are connected to the multiplexed Input output
pins. Bank 0 and 1 to mio and bank 3 and 4 to extended multiplexed input
output pins.
Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf
On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.
In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.
You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
If gpio is not set to wake disable the interrupt. ATF set all slaves with
enabled interrupts as wakeup sources and if gpio is used in r5 then it
wakes up linux.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add Versal support in gpio.
Only bank 0 and 3 are connected to the Multiplexed Input output pins.
Bank 0 to mio and bank3 to fabric Multiplexed input output pins.
Versal devices are the industry's first adaptive compute
acceleration platforms.
https://www.xilinx.com/support/documentation/data_sheets/ds950-versal-overview.pdf
On the Versal platform, we are using two customized GPIO controllers(IP)
which were used in Zynq/ZynqMp platform.
One of them present in the Platform Management Controller(PMC) block and
other in Processing System(PS) block.
In PMC_GPIO only Bank0,1,3 & 4 are enabled and in PS_GPIO only
Bank 0 & 3 are enabled.
You can find more details of GPIO IP in ZynqMP TRM General Purpose
I/O(Chapter-27).
https://www.xilinx.com/support/documentation/user_guides/ug1085-zynq-ultrascale-trm.pdf
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Fix race condition when changing the direction (in/out) of the GPIO pin.
The read-modify-write sequence (as coded in the driver) isn't atomic and
requires synchronization (spinlock).
Signed-off-by: Glenn Langedock <Glenn.Langedock@barco.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When adding a quirk for IRQ on Intel Galileo Gen 2 the commit ba8c90c618
("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
missed GPIO resource release. We can safely do this in the same quirk, since
IRQ will be locked by GPIO framework when requested and unlocked on freeing.
Fixes: ba8c90c618 ("gpio: pca953x: Override IRQ for one of the expanders on Galileo Gen 2")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The pdata is already checked for its validity.
Remove the redundant check.
Signed-off-by: Gaurav Singh <gaurav1086@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Nandor Han <nandor.han@ge.com>
Cc: Semi Malinen <semi.malinen@ge.com>
Link: https://lore.kernel.org/r/20200615150545.87964-5-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make use of for_each_requested_gpio() instead of home grown analogue.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: "Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>
Cc: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200615150545.87964-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Split the cdev specific functionality out of gpiolib.c and into
gpiolib-cdev.c. This improves the readability and maintainability of both
the cdev and core gpiolib code.
Suggested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Kent Gibson <warthog618@gmail.com>
Link: https://lore.kernel.org/r/20200616093615.5167-1-warthog618@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It's a repetition of the commit aa58a21ae3
("gpio: pca953x: disable regmap locking")
which states the following:
This driver uses its own locking but regmap silently uses
a mutex for all operations too. Add the option to disable
locking to the regmap config struct.
Fixes: bcf41dc480 ("gpio: pca953x: fix handling of automatic address incrementing")
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The commit 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
seems inadvertently made a typo in pca953x_irq_bus_sync_unlock().
When the direction bit is 1 it means input, and the piece of code in question
was looking for output ones that should be turned to inputs.
Fix direction setting when configure an IRQ by injecting a bitmap complement
operation.
Fixes: 0f25fda840 ("gpio: pca953x: Zap ad-hoc reg_direction cache")
Depends-on: 35d13d9489 ("gpio: pca953x: convert to use bitmap API")
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
ACPI table on Intel Galileo Gen 2 has wrong pin number for IRQ resource
of one of the I²C GPIO expanders. Since we know what that number is and
luckily have GPIO bases fixed for SoC's controllers, we may use a simple
DMI quirk to match the platform and retrieve GpioInt() pin on it for
the expander in question.
Mika suggested the way to avoid a quirk in the GPIO ACPI library and
here is the second, almost rewritten version of it.
Fixes: f32517bf1a ("gpio: pca953x: support ACPI devices found on Galileo Gen2")
Depends-on: 25e3ef894e ("gpio: acpi: Split out acpi_gpio_get_irq_resource() helper")
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The PCAL9535 is compatible to the PCA9535. Additionally, it comes with
interrupt support and input latching. Other features are not supported
by the GPIO subsystem.
Datasheet: https://www.nxp.com/docs/en/data-sheet/PCAL9535A.pdf
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count if pm_runtime_put is not called in
error handling paths. Call pm_runtime_put if pm_runtime_get_sync fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200605030052.78235-1-navid.emamdoost@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Calling pm_runtime_get_sync increments the counter even in case of
failure, causing incorrect ref count. Call pm_runtime_put if
pm_runtime_get_sync fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200605025207.65719-1-navid.emamdoost@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The word 'descriptor' is misspelled throughout the tree.
Fix it up accordingly:
decriptors -> descriptors
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Delete the interrupt IRQF_NO_THREAD flags in order to gpio interrupts
can be threaded to allow high-priority processes to preempt.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Use kobj_to_dev() API instead of container_of().
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
Full details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXtzqVA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynftwCfeanyI6TR5AdfJVZN50B6/ySvVwcAn07i9VRX
tnt2kz0UqReYpLt0wyJ7
=YP7o
-----END PGP SIGNATURE-----
Merge tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY driver updates from Greg KH:
"Here are the large set of USB and PHY driver updates for 5.8-rc1.
Nothing huge, just lots of little things:
- USB gadget fixes and additions all over the place
- new PHY drivers
- PHY driver fixes and updates
- XHCI driver updates
- musb driver updates
- more USB-serial driver ids added
- various USB quirks added
- thunderbolt minor updates and fixes
- typec updates and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (245 commits)
usb: dwc3: meson-g12a: fix USB2 PHY initialization on G12A and A1 SoCs
usb: dwc3: meson-g12a: fix error path when fetching the reset line fails
Revert "dt-bindings: usb: qcom,dwc3: Convert USB DWC3 bindings"
Revert "dt-bindings: usb: qcom,dwc3: Add compatible for SC7180"
Revert "dt-bindings: usb: qcom,dwc3: Introduce interconnect properties for Qualcomm DWC3 driver"
USB: serial: ch341: fix lockup of devices with limited prescaler
USB: serial: ch341: add basis for quirk detection
CDC-ACM: heed quirk also in error handling
USB: serial: option: add Telit LE910C1-EUX compositions
usb: musb: Fix runtime PM imbalance on error
usb: musb: jz4740: Prevent lockup when CONFIG_SMP is set
usb: musb: mediatek: add reset FADDR to zero in reset interrupt handle
usb: musb: use true for 'use_dma'
usb: musb: start session in resume for host port
usb: musb: return -ESHUTDOWN in urb when three-strikes error happened
USB: serial: qcserial: add DW5816e QDL support
thunderbolt: Add trivial .shutdown
usb: dwc3: keystone: Turn on USB3 PHY before controller
dt-bindings: usb: ti,keystone-dwc3.yaml: Add USB3.0 PHY property
dt-bindings: usb: convert keystone-usb.txt to YAML
...
Core changes:
- A new GPIO aggregator driver has been merged: this can
join a few select GPIO lines into a new aggregated GPIO
chip. This can be used for security: a process can be
granted access to only these lines, for example for
industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or
container.
- Warn if the gpio-line-names is too long in he DT parser
core.
- GPIO lines can now be looked up by line name in addition
to being looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too
many regmap drivers are starting to look like each other
so we need to create some common ground and try to move
drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines
and several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey
Semin has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger
effort to make the ARM platforms more modular.
-----BEGIN PGP SIGNATURE-----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=B5OK
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.8 kernel cycle.
Core changes:
- A new GPIO aggregator driver has been merged: this can join a few
select GPIO lines into a new aggregated GPIO chip. This can be used
for security: a process can be granted access to only these lines,
for example for industrial control. Another way to use this is to
reexpose certain select lines to a virtual machine or container.
- Warn if the gpio-line-names is too long in he DT parser core.
- GPIO lines can now be looked up by line name in addition to being
looked up by offset.
New drivers:
- A new generic regmap GPIO driver has been merged. Too many regmap
drivers are starting to look like each other so we need to create
some common ground and try to move drivers over to using that.
- The F7188X driver now supports F81865.
Driver improvements:
- Large improvements to the PCA953x expander, get multiple lines and
several cleanups.
- Large improvements to the DesignWare DWAPB driver, and Sergey Semin
has volunteered to maintain it.
- PL061 can now be built as a module, this is part of a bigger effort
to make the ARM platforms more modular"
* tag 'gpio-v5.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (77 commits)
gpio: pca953x: Drop unneeded ACPI_PTR()
MAINTAINERS: Add gpio regmap section
gpio: add a reusable generic gpio_chip using regmap
gpiolib: Introduce gpiochip_irqchip_add_domain()
gpio: gpiolib: Allow GPIO IRQs to lazy disable
gpiolib: Separate GPIO_GET_LINEINFO_WATCH_IOCTL conditional
gpio: rcar: Fix runtime PM imbalance on error
gpio: pca935x: Allow IRQ support for driver built as a module
gpio: pxa: Add COMPILE_TEST support
dt-bindings: gpio: Add renesas,em-gio bindings
MAINTAINERS: Fix file name for DesignWare GPIO DT schema
gpio: dwapb: Remove unneeded has_irq member in struct dwapb_port_property
gpio: dwapb: Don't use IRQ 0 as valid Linux interrupt
gpio: dwapb: avoid error message for optional IRQ
gpio: dwapb: Call acpi_gpiochip_free_interrupts() on GPIO chip de-registration
gpio: max730x: bring gpiochip_add_data after port config
MAINTAINERS: Add GPIO Aggregator section
docs: gpio: Add GPIO Aggregator documentation
gpio: Add GPIO Aggregator
gpiolib: Add support for GPIO lookup by line name
...
- Cleanup of the irq_domain API
- Overhaul of the interrupt chip simulator
- The usual pile of new interrupt chip drivers
- Cleanups, improvements and fixes all over the place
-----BEGIN PGP SIGNATURE-----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=Pi5h
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"The generic interrupt departement provides:
- Cleanup of the irq_domain API
- Overhaul of the interrupt chip simulator
- The usual pile of new interrupt chip drivers
- Cleanups, improvements and fixes all over the place"
* tag 'irq-core-2020-06-02' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
irqchip: Fix "Loongson HyperTransport Vector support" driver build on all non-MIPS platforms
dt-bindings: interrupt-controller: Add Loongson PCH MSI
irqchip: Add Loongson PCH MSI controller
dt-bindings: interrupt-controller: Add Loongson PCH PIC
irqchip: Add Loongson PCH PIC controller
dt-bindings: interrupt-controller: Add Loongson HTVEC
irqchip: Add Loongson HyperTransport Vector support
genirq: Check irq_data_get_irq_chip() return value before use
irqchip/sifive-plic: Improve boot prints for multiple PLIC instances
irqchip/sifive-plic: Setup cpuhp once after boot CPU handler is present
irqchip/sifive-plic: Set default irq affinity in plic_irqdomain_map()
irqchip/gic-v2, v3: Drop extra IRQ_NOAUTOEN setting for (E)PPIs
irqdomain: Allow software nodes for IRQ domain creation
irqdomain: Get rid of special treatment for ACPI in __irq_domain_add()
irqdomain: Make __irq_domain_add() less OF-dependent
iio: dummy_evgen: Fix use after free on error in iio_dummy_evgen_create()
irqchip/gic-v3-its: Balance initial LPI affinity across CPUs
irqchip/gic-v3-its: Track LPI distribution on a per CPU basis
genirq/irq_sim: Simplify the API
irqdomain: Make irq_domain_reset_irq_data() available to non-hierarchical users
...
ACPI_PTR() becomes a no-op when !CONFIG_ACPI. This is not needed since
we always have ID table enabled. Moreover, in the mentioned case compiler
will complain about defined but not used variable.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200520211916.25727-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are quite a lot simple GPIO controller which are using regmap to
access the hardware. This driver tries to be a base to unify existing
code into one place. This won't cover everything but it should be a good
starting point.
It does not implement its own irq_chip because there is already a
generic one for regmap based devices. Instead, the irq_chip will be
instantiated in the parent driver and its irq domain will be associate
to this driver.
For now it consists of the usual registers, like set (and an optional
clear) data register, an input register and direction registers.
Out-of-the-box, it supports consecutive register mappings and mappings
where the registers have gaps between them with a linear mapping between
GPIO offset and bit position. For weirder mappings the user can register
its own .xlate().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-3-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function connects an IRQ domain to a gpiochip and reuses
gpiochip_to_irq() which is provided by gpiolib.
gpiochip_irqchip_* and regmap_irq partially provide the same
functionality. This function will help to connect just the
minimal functionality of the gpiochip_irqchip which is needed to
work together with regmap-irq.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200528145845.31436-2-michael@walle.cc
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- A few new drivers for the Loongson MIPS platform (HTVEC, PIC, MSI)
- A cleanup of the __irq_domain_add() API
- A cleanup of the IRQ simulator to actually use some of
the irq infrastructure
- Some fixes for the Sifive PLIC when used in a multi-controller
context
- Fixes for the GICv3 ITS to spread interrupts according to the
load of each CPU, and to honor managed interrupts
- Numerous cleanups and documentation fixes
-----BEGIN PGP SIGNATURE-----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=RX31
-----END PGP SIGNATURE-----
Merge tag 'irqchip-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates from Marc Zyngier:
- A few new drivers for the Loongson MIPS platform (HTVEC, PIC, MSI)
- A cleanup of the __irq_domain_add() API
- A cleanup of the IRQ simulator to actually use some of
the irq infrastructure
- Some fixes for the Sifive PLIC when used in a multi-controller
context
- Fixes for the GICv3 ITS to spread interrupts according to the
load of each CPU, and to honor managed interrupts
- Numerous cleanups and documentation fixes
We provided the right semantics on open drain lines being
by definition output but incidentally the irq set up function
would only allow IRQs on lines that were "not output".
Fix the semantics to allow output open drain lines to be used
for IRQs.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Russell King <linux@armlinux.org.uk>
Cc: stable@vger.kernel.org # v5.3+
Link: https://lore.kernel.org/r/20200527140758.162280-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With 'commit 461c1a7d47 ("gpiolib: override irq_enable/disable")' gpiolib
overrides irqchip's irq_enable and irq_disable callbacks. If irq_disable
callback is implemented then genirq takes unlazy path to disable irq.
Underlying irqchip may not want to implement irq_disable callback to lazy
disable irq when client drivers invokes disable_irq(). By overriding
irq_disable callback, gpiolib ends up always unlazy disabling IRQ.
Allow gpiolib to lazy disable IRQs by overriding irq_disable callback only
if irqchip implemented irq_disable. In cases where irq_disable is not
implemented irq_mask is overridden. Similarly override irq_enable callback
only if irqchip implemented irq_enable otherwise irq_unmask is overridden.
Fixes: 461c1a7d47 ("gpiolib: override irq_enable/disable")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Link: https://lore.kernel.org/r/1590253873-11556-2-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We already have two conditionals inside the outer one to check
if the command is GPIO_GET_LINEINFO_WATCH_IOCTL. I think it's
time to actually do what I have proposed in the first place, i.e.
to separate GPIO_GET_LINEINFO_WATCH_IOCTL from GPIO_GET_LINEINFO_IOCTL.
It's +13 LOCs, and surprisingly only +13 bytes of binary on x86_32,
but for the price of much better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Link: https://lore.kernel.org/r/20200525194028.74236-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- fix the initialization ordering in gpio-max730x
- make gpio-pxa buildable for compile testing
- make gpio-pca953x buildable as a module
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEFp3rbAvDxGAT0sefEacuoBRx13IFAl7ONccACgkQEacuoBRx
13Kh/Q//bdyJU70HyvXI2240gXqcbblrXVx+BcBYIAxh61r2XdDOND9guUlsuT6+
gE74fVA6ed1enjjFTkaNXiIsvHTPAG0ABz3nbXJ1dL27NBgItmfWM8EfjAJOCcA6
z/kQkM8fooSoLtt2Zrdf5M3F2OyvJIgcVQm4JENqJKdJvd7T7xIKISr2UFAjNg/R
ms/rD1IKsqu8Xegok1L85sC1nYSYxYKhGKZsWlG+HHl9NDWDo5CI6oxvf7YT0ePK
dTxnM8ijY0NumLfiDJIwkdTAejnB1hJybrItojdmcwFhJmcckeNs9tIE4TM0wleH
lsJZllmA7YfybPB2uvwCmoJYLK93+qFzehpquB+3pwV0VRTNYivscOkMW18JFdwC
2VUgAIQeQ8g8HMnIYWjnPuudU/yYDu2iYyGZdaowxdo1W1i8Gn2BiyCawdmRDarl
HpWwQByzynfOWSr5RjBHZ/G1tBQ4l8bjoCJFHsbFjOJTwquieSNx71OMhhysx1pp
rb1t2r778zvihnl+JckvtLwZ8Vvf9iVYf81ZqXy9WIdJM1yECUensFWPHBxaCjz6
7JjYertJNI5DL93+HwstKdl8DnIP3FZDGryPeqQVlXlUeWXHyyLSseuRc5OM1bVS
CiJ/l2T+By5mek7qZ0kbTmVeTCvHHz7OCSExsN1/sAuz4eUFcec=
=yCpP
-----END PGP SIGNATURE-----
Merge tag 'gpio-updates-for-v5.8-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into devel
gpio: updates for v5.8 - part 2
- fix the initialization ordering in gpio-max730x
- make gpio-pxa buildable for compile testing
- make gpio-pca953x buildable as a module
pm_runtime_get_sync() increments the runtime PM usage counter even
when it returns an error code. Thus a pairing decrement is needed on
the error handling path to keep the counter balanced.
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Link: https://lore.kernel.org/r/20200522080839.32612-1-dinghao.liu@zju.edu.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Perhaps by some historical reasons the IRQ support has been allowed
only for built-in driver. However, there is nothing prevents us
to build it as module an use as IRQ chip.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Propagate the error code returned by devm_platform_ioremap_resource()
out of probe() instead of overwriting it.
Fixes: 72d8cb7154 ("drivers: gpio: bcm-kona: use devm_platform_ioremap_resource()")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Add COMPILE_TEST support to the PXA GPIO driver for better compile
testing coverage.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 542c25b7a2 ("drivers: gpio: pxa: use devm_platform_ioremap_resource()")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
has_irq member of struct dwapb_port_property is used only in one place,
so, make it local test instead and remove from the structure.
This local test is using memchr_inv() which is quite efficient in comparison
to the original loop and possible little overhead can be neglected.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-4-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
IRQ 0 is not valid in Linux interrupt number space.
Refactor the code with this kept in mind.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
platform_get_irq() will generate an error message if the requested IRQ
is not present. Use platform_get_irq_optional() to avoid the error message
being generated.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Acked-by: Serge Semin <fancer.lancer@gmail.com>
Link: https://lore.kernel.org/r/20200519131233.59032-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
