Fix power well control state by reading real register offset.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We were writing DSP_ADDR and DSP_SURF unconditionally. This did not
trigger an unclaimed write before HSW as the address of DSP_ADDR has
been repurposed as DSP_LINOFF.
On HSW, though, DSP_LINOFF has been removed and then writting to it
triggers an unclaimed write.
This patch writes to DSP_ADDR or DSP_SURF to flush the display plane
configuration depending on the gen we're running on.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Comment says for eaglelake/cantiga, but it's listed in the ilk table,
too. So apply it to both.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Or at least our best understanding of it.
v2: Fixup commit message and put the wa name into the comment block.
And actually update the commit, too.
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like in:
commit c2c7513124
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 5 12:17:30 2012 +0200
drm/i915: adjust framebuffer base address on gen4+
but this time, for the sprite planes. This ensures that the
sprite offset are always inside the supported hardware limits since it
becomes the offset into a page and we adjust the base address to a page
boundary.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
HSW consolidates SPRTILEOFF and SPRLINOFF into a single SPROFFSET
register.
v2: Remove a useless level of indentation (Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2: Use a switch for consistency (Chris Wilson)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Instead of writing to the DSP_ADDR ourselves. This will do the right
thing on gen >= 4 as well.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
And properly toggle the chicken bit in the pch to enable/disable fdi C
rx. If we don't set this bit correctly, the rx gets confused in link
training, which can result in an fdi link that silently fails to train
the link (since the corresponding register reports success). Note that
both fdi link B and C can suffer when this bit is not set correctly.
The code as-is has a few deficiencies:
- We presume all pipes use the pch which is not the case for cpu edp.
- We don't bother with disabling both pipes when we could make things
work, e.g. when pipe B switched from 4 to 2 lanes due to a mode
change, we don't bother updating the w/a bit.
- It's ugly.
All of these are because we compute ->fdi_lanes way too late, when
we're already setting up individual pipes. We need to have this
information in ->modeset_global_resources already, to set things up
correctly. But that is a much larger reorg of the code.
Note that we actually hit the 2 lanes limit in practice rather
quickly: Even though the 1920x1200 mode native mode of my screen fits
into 2 lanes, it needs 3 lanes for the 1920x1080 (since that somehow
has much more blanking ...). Not obeying this restriction seems to
results in cute-looking digital noise.
v2: Only ever clear the chicken bit when both pipes are off.
v3: Use the new ->modeset_global_resources callback.
v4: Move the WARNs to the right place. Oh how I hate hacks.
v5: Fix spelling, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After all relevant pipes are disabled and after we've updated all the
state with the staged state, but before we call the per-crtc
->mode_set functions there's a very natural point to set up any
shared/global resources like
- shared plls (obviously only the setup, the enabling needs to be
separately handling with a separate refcount)
- global watermark state like the DSPARB on gmch platforms
- workaround bits that depend upon the exact global output
configuration
- enabling the right set of refclocks
- enabling/disabling manual power wells.
Now for a lot of these things we can't move them into this function
yet, most often because we only compute the required information in
the per-crtc ->mode_set callback. Which is too late. But due to a
bunch of reasons (check-only atomic modeset, fastboot&hw state checks,
...) we need to separate the computation of that state from the actual
hw frobbery anyway. So we can move things into this new callback step-
by-step.
Others can't be moved here (or implemented at all) because our code
lacks the smarts to properly update them. E.g. the DSPARB can only be
updated when all pipes are disabled, so if we decide to change it's
value, we need to disable _all_ pipes. The infrastructure for that is
already in place (with the various pipe masks that driver the modeset
logic). But again we need to move a few things out of ->mode_set
first before we can even implement the correct decision making.
In any case, we need to start somewhere, so let's start with the
callback: Some small follow-up patches will make immediate good use of
it.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since it is one. We need to move this code to encoder specific callbacks
eventually, to kill all that inversion of control ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Atm we have a few funny issues where we enable/disable shared
pll clocks. To make it clear that we are not required to enable/
disable the pch plls together with the other pch resources (and
so should keep it running when it's used by another pipe in
a shared pll configuration) add a comment.
This note is lifted from "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 9.d. of the enable
sequence:
"Configure and enable PCH DPLL, wait for PCH DPLL warmup (Can be
done anytime before enabling PCH transcoder)."
Since fixing the pll sharing code to no longer disable shared plls
if they're still in use is more involved, let's just stick with the
comment for now.
v2: Make the comment in the code clearer, to address questions raised
by Paulo Zanoni in review.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My machine here has the correct ones already, but better safe
than sorry. IBX has different settings for that register, and
on IBX the device defaults match the recommended values. Hence
I did not add the respective writes for IBX.
LPT needs the same settings, but that has been done already
commit 4acf518626
Author: Eugeni Dodonov <eugeni.dodonov@intel.com>
Date: Wed Jul 4 20:15:16 2012 -0300
drm/i915: program FDI_RX TP and FDI delays
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reference, see "Graphics BSpec: vol4g North Display Engine
Registers [IVB], Display Mode Set Sequence", step 4 of the enabling
sequence:
a. "Enable PCH FDI Receiver PLL, wait for warmup plus DMI latency
b. "Switch from Rawclk to PCDclk in FDI Receiver
c. "Enable CPU FDI Transmitter PLL, wait for warmup"
Cc: Paulo Zanoni <przanoni@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
According to "Graphics BSpec: vol4g North Display Engine Registers [IVB],
Display Mode Set Sequence" We need to write the TU size register
of the fdi RX unit _before_ starting to train the link.
Note: The current code is actually correct as Paulo mentioned in
review, but it's a bit confusion since only the fdi rx/tx plls need to
be enabled before the cpu pipes/planes. Hence it's still a good idea
to move the TU_SIZE setting to the "right" spot in the sequence, to
better match Bspec.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The debug message is only relevant on CPT/PPT PCH ports, so move
it into the correct if clause.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Drop the NULL test for dev since it never be NULL.
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There are still some mysteries left, in particular how (and in
fact if) the EDID is supposed to work on the HDMI port. However
the basic stuff now works and I can plug my Q550 into an HDMI
display and get the expected results.
[v2: cleans up space/tab and other formatting as per Dave's
request]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case of a blob property drm_property_change_is_valid() can't
tell whether the change is valid or not. So just return true
for all blob properties, and leave it up to someone else to
check it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
None of drm_mode_debug_printmodeline(), drm_mode_equal(), drm_mode_width()
or drm_mode_height() change the mode passed in, so make the arguments
const.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Daniel's backmerge
commit c2fb791692
Merge: 29de6ce6f0c058
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Oct 22 14:34:51 2012 +0200
Merge tag 'v3.7-rc2' into drm-intel-next-queued
to solve conflicts blew up (either git or Daniel was trying to be too
clever for their own good; it's usually convenient to blame tools ;) and
caused the changes of
commit 0c96c65b48
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Sep 26 18:43:10 2012 +0300
drm/i915: use adjusted_mode instead of mode for checking the 6bpc force flag
in ironlake_crtc_mode_set() to be dropped.
Fix the call in ironlake_crtc_mode_set() again, and while at it, also fix
the new, copy-pasted haswell_crtc_mode_set() to use adjusted_mode.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When buffer sharing with the i915 and using a 1680x1050 monitor,
the i915 gives is a 6912 buffer for the 6720 width, the code doesn't
render this properly as it uses one value to set the base address for
reading from the vmap and for where to start on the device.
This fixes it by calculating the values correctly for the device and
for the pixmap. No idea how I haven't seen this before now.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Inki writes:
"As I posted before, we have added a new git repository for Exynos drm
to MAINTAINERS file so change it to new one like below,
from git://git.infradead.org/users/kmpark/linux-samsung
to git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos
And this pull request includes the following:
- fix display on issue when user requested dpms mode changing.
- add git repository for Exynos drm to MAINTAINERS file.
- add support for ARCH_MULTIPLATFORM.
- and code clean."
* 'exynos-drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm: exynos: removed warning due to missing typecast for mixer driver data
drm/exynos: add support for ARCH_MULTIPLATFORM
MAINTAINERS: Add git repository for Exynos DRM
drm/exynos: fix display on issue
Alex writes:
"This request is mostly load detection fixes from Egbert and me."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add load detection support for ext DAC on R200 (v2)
DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
DRM/Radeon: Clean up code in TV DAC load detection.
drm/radeon: fix ATPX function documentation
drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
DRM/Radeon: Fix Load Detection on legacy primary DAC.
Daniel Vetter writes"
Nothing big at all for -fixes, just small stuff:
- Two patches to fix bugs on i830M
- ums regression fixer due to kicking firmeware fbs (Chris)
- tune down a too loud warning (Jani)
- be more careful with sdvo infoframes, which fixes a long-standing
sdvo-hdmi regression"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
drm/i915: be less verbose about inability to provide vendor backlight
drm/i915: clear the entire sdvo infoframe buffer
drm/i915: VGA needs to be on pipe A on i830M
drm/i915: fix overlay on i830M
The R200 asics use an external DAC for the secondary DAC.
The current KMS code tries to use code for the integrated
TV DAC for R200 which leads to unpredictable results since
R200 does not have an integrated TV DAC. This patch ports
the external DAC load detection support from the UMS
driver to KMS.
v2: fix typo in loop break logic
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Egbert Eich <eich@suse.de>
On all dual CRTC GPUs the CRTC_CRT_ON in the RADEON_CRTC_EXT_CNTL register
controls the CRTC of the primary DAC. Therefore it is set in the DAC DMPS
function.
This is different for GPU's with a single CRTC but a primary and a
TV DAC: here it controls the single CRTC no matter where it is routed.
Therefore we set it here. This avoids an elaborate on/off state tracking
since both primary_dac_dpms() and tv_dac_dpms() functions would have
to touch this bit.
On single CRTC GPUs with just one DAC it's irrelevant where this bit
is handled.
agd5f: fix warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The RN50 has a TV DAC but only a single CRTC. For load detection this
DAC is controlled by the primary CRTC.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@r1@
statement S;
position p,p1;
@@
S@p1;@p
@script:python r2@
p << r1.p;
p1 << r1.p1;
@@
if p[0].line != p1[0].line_end:
cocci.include_match(False)
@@
position r1.p;
@@
-;@p
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The Radeon driver uses the analog/digital flag to determine if the
DAC or the TMDS encoder should be enabled on a DVI-I connector.
If the EDID is bogus this flag is no longer reliable. This fix
adds a fallback to DAC load detection to determine if anything
is connected to the DAC. If not and a (bogus) EDID is found it
assumes a digital display is connected.
This works around problems with some crappy IPMI devices using
Radeon ES1000.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For Radeon 7500 ATI recommends a DAC_FORCE value of 0x1ac. This value
works better on ES1000 (RV100) chips, too, as it doesn't produce any false
positives on any cards I have tested. Therefore let's assume that this
value is good for all RV100 and RV200 chipset generations.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
An uninitialized variable led to broken load detection.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Removing the warning by adding proper type casting where local pointer
variable of type mixer driver data is assigned with void pointer.
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Exynos does not seem to have any dependency on anything from
platform headers so just needs Kconfig updated to build in
ARCH_MULTIPLATFORM builds.
Signed-off-by: Rob Clark <rob@ti.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
When crtc_funcs->dpms callback is called, exynos_crtc->dpms
and exynos_encoder->dpms are changed to new mode. But if user
requests dpms mode operation, OFF -> ON, when crtc's dpms callback
is called, exynos_encoder->dpms is also changed to ON. This
makes encoder's dpms callback call be ignored so display power
couldn't become on again.
This patch removes exynos_encoder->dpms changing and adds 'updated'
variable to exynos_drm_encoder structure to avoid duplicated overlay
updating.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Useful for places where a given chipset may or may not have a given
resource, and we want to avoid having to spray checks for the mm's
existance around everywhere.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Yuly Novikov <ynovikov@chromium.org>
[Jani: ripped this change separate from the scaling mode change support]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for supporting scaling mode configuration also in eDP.
Includes a drive-by-removal of an outdated comment about fitting mode.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At some point the DPCD size was increased, but the debug print not. While
at it, switch to using hex dump.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just like HSW, VLV does not have a sprite scale. Set
intel_plane->can_scale accordingly.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise we may remove the only console for a nomodeset system.
We became more aggressive in our kicking with
commit e188719a28
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Jun 12 11:28:17 2012 +0200
drm/i915: kick any firmware framebuffers before claiming the gtt
Reported-and-tested-by: monnier@iro.umontreal.ca
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=54615
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org # v3.6
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 28dcc2d60c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Mon Sep 3 16:25:12 2012 +0300
drm/i915: do not expose a dysfunctional backlight interface to userspace
prevents backlight interface creation if the BIOS has not set the backlight
PWM CTL registers that contain the max PWM value. It's apparently normal on
those machines, so demote the message about it to debug level.
Reported-by: Orion Poplawski <orion@cora.nwra.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56330
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVOB may be multiplexed with HDMIB. If it's not SDVOB, the same i2c
adapter may be used for HDMIB, with the adjusted config (i.e. with GPIO
bit-banging instead of gmbus). Restore i2c adapter config before error
return from intel_sdvo_init(), letting HDMIB enjoy the joys of gmbus.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 63abf3edaf
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Wed Dec 8 16:48:21 2010 +0000
drm/i915/sdvo: Only use the SDVO pin if it is in the valid range
added a default fallback if BIOS provides an invalid pin mapping, but
failed to force GPIO bit-banging on it. Finish the job, and also clean up
the function a bit. With bit-banging, setting the gmbus speed has no
effect, so drop it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
[danvet: Extend comment about gmbus in the code a bit.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Now that all the eDP enablement bits are there, we can actually try to
use the eDP.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's an important step :)
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The cdclk frequency is not always the same, so the value here should
be adjusted to match it.
Version 2: call intel_ddi_get_cdclk_freq instead of reading
CDCLK_FREQ, because the register is just for earlier HW steppings.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
See the documentation for the DDI_FUNC_CTL register, EDP Input Select
bits: when the EDP input selection is B, the VTOTAL_B must be
programmed with the VTOTAL_EDP value, same thing for selection C.
V2: Use I915_READ as suggested by Daniel Vetter.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same thing as the previous commits. Not renaming this one since it
exists since way before Haswell.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Same as the other registers. This one also appeared on Haswell for the
first time, so that's why we are renaming it.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because the PIPECONF register is actually part of the CPU transcoder,
not the CPU pipe.
Ideally we would also rename PIPECONF to TRANSCONF to remind people
that they should use the transcoder instead of the pipe, but let's
keep it like this for now since most Gens still name it PIPECONF.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need to check if any of the pipes is using TRANSCODER_EDP.
V2: DDI_BUF_CTL was renamed, so fix the usage here.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Because there's one instance of the register per CPU transcoder and
not per CPU pipe. This is another register that appeared for the first
time on Haswell, and even though its Haswell name is
PIPE_DDI_FUNC_CTL, it will be renamed to TRANS_DDI_FUNC_CTL, so let's
just use the new naming scheme before it confuses more people.
Notice that there's a big improvement on intel_ddi_get_hw_state due to
the new TRANSCODER_EDP.
V2: Also rename the register to TRANS_DDI_FUNC_CTL as suggested by
Damien Lespiau.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This register appeared in Haswell. It does not have an EDP version
because the EDP transcoder is always tied to the DDIA clock. Notice
that if we call PIPE_CLK_SEL(pipe) when pipe is PIPE_A and transcoder
is TRANSCODER_EDP we might introduce a bug, that's why this is a
transcoder register even though it does not have an EDP version.
Even though Haswell names this register PIPE_CLK_SEL, it will be
renamed to TRANS_CLK_SEL in the future, so let's just start using the
real name that makes more sense and avoids misusage.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Before Haswell we used to have the CPU pipes and the PCH transcoders.
We had the same amount of pipes and transcoders, and there was a 1:1
mapping between them. After Haswell what we used to call CPU pipe was
split into CPU pipe and CPU transcoder. So now we have 3 CPU pipes (A,
B and C), 4 CPU transcoders (A, B, C and EDP) and 1 PCH transcoder
(only used for VGA).
For all the outputs except for EDP we have an 1:1 mapping on the CPU
pipes and CPU transcoders, so if you're using CPU pipe A you have to
use CPU transcoder A. When have an eDP output you have to use
transcoder EDP and you can attach this CPU transcoder to any of the 3
CPU pipes. When using VGA you need to select a pair of matching CPU
pipes/transcoders (A/A, B/B, C/C) and you also need to enable/use the
PCH transcoder.
For now we're just creating the cpu_transcoder definitions and setting
cpu_transcoder to TRANSCODER_EDP on DDI eDP code, but none of the
registers was ported to use transcoder instead of pipe. The goal is to
keep the code backwards-compatible since on all cases except when
using eDP we must have pipe == cpu_transcoder.
V2: Comment the haswell_crtc_off chunk, suggested by Damien Lespiau
and Daniel Vetter.
We currently need the haswell_crtc_off chunk because TRANSCODER_EDP
can be used by any CRTC, so when you stop using it you have to stop
saying you're using it, otherwise you may have at some point 2 CRTCs
claiming they're using TRANSCODER_EDP (a disabled CRTC and an enabled
one), then the HW state readout code will get completely confused.
In other words:
Imagine the following case:
xrandr --output eDP1 --auto --crtc 0
xrandr --output eDP1 --off
xrandr --output eDP1 --auto --crtc 2
After the last command you could get a "pipe A assertion failure
(expected off, current on)" because CRTC 0 still claims it's using
TRANSCODER_EDP, so the HW state readout function will read it
(through PIPECONF) and expect it to be off, when it's actually on
because it's being used by CRTC 2.
So when we make "intel_crtc->cpu_transcoder = intel_crtc->pipe" we
make sure we're pointing to our own original CRTC which is certainly
not used by any other CRTC.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On Ironlake we have one PCH transcoder and FDI per pipe, so we know
that if ironlake_crtc_driving_pch returns false we can disable the PCH
transcoder and we also know that when we disable the crtc we can also
disable the PCH transcoder.
On Haswell there is only 1 PCH transcoder and FDI and they can be used
by any CRTC. So if for one specific crtc haswell_crtc_driving_pch
returns false we can't assert anything about the state of the PCH
transcoder or the FDI link without checking if any other CRTC is using
the PCH.
So on this commit remove the "assert_fdi_{t,r}x_disabled" form
haswell_crtc_enable and also only disable FDI and the PCH transcoder
if the port being disabled was actually a PCH port (we only have one
port using PCH: the VGA port).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
By forking Ironlake and Haswell functions. The only callers are
{ironlake,haswell}_crtc_enable anyway, and this way we won't need to
add other checks on the Haswell version for the next gens.
V2: Even simpler, as pointed by Jani Nikula.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These functions were forked from their Ironlake versions, so now fix
the gen checks to reflect the fact that they will only run on Haswell.
It is worth noticing that we are not considering IBX/CPT possible on
Haswell anymore. So far on Haswell enablement we kept trying to still
consider IBX/CPT as a possibility with a Haswell CPU, but this was
never tested, I really doubt it will work with the current code and we
don't really have plans to support it. Future patches will remove the
IBX/CPT code from other Haswell functions. Notice that we still have a
WARN on haswell_crtc_mode_set in case we detect non-LPT PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The last commit forked a Haswell version, so now we remove Haswell
code from these functions.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The way we enable and disable the PCH on Haswell changed considerably
since now we have only one PCH transcoder, so we can't keep the same
asserts and we also can't just unconditionally disable the PCH
transcoder for non-PCH outputs. So let's fork a Haswell version.
These new functions look exactly the same as the ironlake versions.
The next patches will introduce the differences.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Identical #define is now available in include/drm/drm_dp_helper.h, nuke the
dupe.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
That thing has grown way too big already.
Also move around a comment to the right spot.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Otherwise dp aux won't work on some hsw platforms, since they use a
different rawclk than the 125MHz clock used thus far.
To absolutely not change anything, round up: That way we get the old
63 divider for the default 125MHz clock.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We need this when the bios forgets even to set that bit up. Most seem
to do that, even when they don't set up anything else in the panel
power sequencer.
Note that on IBX the rawclk is variable according to Bspec, but
everyone is using 125MHz. The rawclk is fixed to 125MHz on CPT, but
luckily we still have the same register available. On hsw, different
variants have different clocks, hence we need to check the register.
Since other pieces are driven by the rawclock, too, keep the little
helper in a central place.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Like we already do for the LVDS panels. This seems to help greatly
in setting up the backlight, since the BIOS might refuse to cooperate.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
v2: Move the backlight_off call from panel_off to edp_backlight_off,
noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Copy and paste typo in the apci rework.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=49351
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
When internal users want VRAM we shouldn't return GART memory instead.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver internal users shouldn't be limited in their allocation size.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When allocating more than 2GB of GART the array of pages
gets to big for kzalloc, use vzalloc instead.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GART and VRAM size limits need to be a power of two.
Fix values greater than 1GB and simplify those checks a bit.
v2: also fix radeon_vram_limit usage, and simplify test even more.
v3: agd5f: fix spelling as noticed by Klaus Schnass
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Like in the case of native hdmi, which is fixed already in
commit adf00b26d1
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date: Tue Sep 25 13:23:34 2012 -0300
drm/i915: make sure we write all the DIP data bytes
we need to clear the entire sdvo buffer to avoid upsetting the
display.
Since infoframe buffer writing is now a bit more elaborate, extract it
into it's own function. This will be useful if we ever get around to
properly update the ELD for sdvo. Also #define proper names for the
two buffer indexes with fixed usage.
v2: Cite the right commit above, spotted by Paulo Zanoni.
v3: I'm too stupid to paste the right commit.
v4: Ben Hutchings noticed that I've failed to handle an underflow in
my loop logic, breaking it for i >= length + 8. Since I've just lost C
programmer license, use his solution. Also, make the frustrated 0-base
buffer size a notch more clear.
Reported-and-tested-by: Jürg Billeter <j@bitron.ch>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=25732
Cc: stable@vger.kernel.org
Cc: Paulo Zanoni <przanoni@gmail.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
3 changes:
- If a given value is unset, use the maximal limits from the eDP spec.
- Write back the new values, since otherwise the panel power sequencing
hw will not dtrt.
- Revert the early bail-out in case the register values are unset.
The last change reverts
commit bfa3384a9a
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Tue Apr 10 11:58:04 2012 -0700
drm/i915: check PPS regs for sanity when using eDP
v2:
- Unlock the PP regs as the very first thing. This is a required w/a
for cpu eDP on port A, and generally a good idea.
- Fixup the panel power control port selection bits.
v3: Paulo Zanoni noticed that I've fumbled the computation of the spec
limit values. Fix them up. We've also noticed that the t8/t9 values in
the vbt/bios-programmed pp are much larger than any limits. My guess
is that this is to conceal any backlight enable/disable delays. So by
using the much shorter limits from the spec, which only concerns the
sink, we risk that we might display before the backlight is fully on,
or disable the output while the backlight still has afterglow. I've
figured I don't care too much, since this will only happen when both
the pp regs are not programmed, and the vbt tables don't contain
anything useful.
v4: Don't set the port selection bits on hsw/LPT, they don't exist any
more.
v5: Fixup spelling issues in comments, as noticed by Jesse Barnes.
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Haswell does not have a scaler in the sprite pipeline anymore, so let's
ensure:
1/ We bail out of update_plate() when someone is trying to ask to
display a scaled framebuffer,
2/ We never write to the nonexistent SPR_SCALE register
v2: Smash in the fixup from Damien in the disable_plane function.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com> (for v1)
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (for v1)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... like the comment says. No idea whether this has any effect, but
I guess it's better to not lie to the display by acking a test request
and never following through with it. This goes back to the commit that
originally introduced this code:
commit a60f0e38d7
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Oct 20 15:09:17 2011 -0700
drm/i915: add DP test request handling
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Meh'ed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only NI uses 3dw headers, SI uses 4dw headers.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's better to handle this in the chipset specific code.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Handle requests that won't fit into a single packet.
v2: pe needs to increase as well.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Handle requests that won't fit into a single packet.
v2: pe needs to increase as well.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise the next IB might start reading commands
with the page table still invalid.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The bit doesn't stick, and the output is always cloned from pipe A,
even when it's supposed to scan out from pipe B.
Shuts up annoying warnings from the modeset-rework, too.
I've noticed that with this patch we know get and unknown connection
state since the code can't find a suitable pipe for load detection.
But that beats the previous state of affairs, where it tried to use
pipe B, actually used pipe A and concluded that something is connected
(although it's the LVDS on pipe A and nothing on the VGA connector on
pipe B).
I've tried to make load detect work by remapping the pipe->planes
stuff, so that crtc 0 will use pipe B and hence we still have
something left for load-detect on pipe A. But alas, that upset the hw
a bit.
So there's still some things to figure out, but this here will at
least paper over some of the problems.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51265
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: extend the commit message a bit with recent observations.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The overlay on the i830M has a peculiar failure mode: It works the
first time around after boot-up, but consistenly hangs the second time
it's used.
Chris Wilson has dug out a nice errata:
"1.5.12 Clock Gating Disable for Display Register
Address Offset: 06200h–06203h
"Bit 3
Ovrunit Clock Gating Disable.
0 = Clock gating controlled by unit enabling logic
1 = Disable clock gating function
DevALM Errata ALM049: Overlay Clock Gating Must be Disabled: Overlay
& L2 Cache clock gating must be disabled in order to prevent device
hangs when turning off overlay.SW must turn off Ovrunit clock gating
(6200h) and L2 Cache clock gating (C8h)."
Now I've nowhere found that 0xc8 register and hence couldn't apply the
l2 cache workaround. But I've remembered that part of the magic that
the OVERLAY_ON/OFF commands are supposed to do is to rearrange cache
allocations so that the overlay scaler has some scratch space.
And while pondering how that could explain the hang the 2nd time we
enable the overlay, I've remembered that the old ums overlay code did
_not_ issue the OVERLAY_OFF cmd.
And indeed, disabling the OFF cmd results in the overlay working
flawlessly, so I guess we can workaround the lack of the above
workaround by simply never disabling the overlay engine once it's
enabled.
Note that we have the first part of the above w/a already implemented
in i830_init_clock_gating - leave that as-is to avoid surprises.
v2: Add a comment in the code.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=47827
Cc: stable@vger.kernel.org
Tested-by: Rhys <rhyspuk@gmail.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, that function could release the lru lock between
checking for bo on ddestroy list and a successful reserve if the bo
was already reserved, and the function was called with waiting reserves
allowed.
However, all current reservers of a bo on the ddestroy list would
atomically take the bo off the list after a successful reserve so this
race should not have been hit, so no need to backport for stable.
This patch also fixes a case found by Maarten Lankhorst where
ttm_mem_evict_first called with no_wait_gpu would incorrectly
spin waiting for bo idle if trying to evict a busy buffer that
also sits on the ddestroy list.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ttm_mem_evict_first function could theoretically drop the
lru lock without retrying if a reservation from off the LRU list
ended up waiting.
However, since currently there are no users that could cause a wait
in that situation so this is not suitable for stable
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Platform device drivers usually use the driver-private data for their
own purposes. Having it overwritten by drm_platform_init() is confusing
and error-prone.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's a relic of "drm: Convert proc files to seq_file and introduce debugfs",
which wrongly converted DRM_INFO + sprintf to 2 seq_printfs.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Cc: Ben Gamari <bgamari@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_gem_cma_create() function never returns NULL but rather an error
encoded in the return value using the ERR_PTR() macro. Callers therefore
need to check for errors using the IS_ERR() macro. This change allows
drivers to handle contiguous DMA allocation failures gracefully.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The debug message showing the resolution of a framebuffer to be
allocated is missing a closing parenthesis.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Only really required for dp 1.2. I've hoped this would help with some
link training woes I'm fighting, but alas those are only dp 1.1
devices.
Also move a comment that went misplaced in the recent refactorings to
the right spot again.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This requires a few changes since that dpcd value is above the
range currently cached by radeon. I've check the dp specs, and
above 0xf there's a big gap and nothing that looks like we should
cache it while a given device is plugged in. It's also the same value
that i915.ko uses.
Hence extend the various dpcd arrays in the radeon driver, use
proper symbolic constants where applicable (one place overallocated
the dpcd array to 25 bytes). Then also drop the rd_interval cache -
radeon_dp_link_train_init re-reads the dpcd block, so the values we'll
consume in train_cr and train_ce will always be fresh.
To avoid needless diff-churn, #define the old size of dpcd as the new
one and keep it around.
v2: Alex Deucher noticed one place where I've forgotten to replace 8
with DP_RECEIVER_CAP_SIZE.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Safe for the minor difference that the intel versions get an offset
into the link_status as an argument, both are the same again.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
radeon and intel use the exact same definition.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
v2: Kill 2 more helpers in intel_dp.c that I've missed.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
radeon and intel use the exact same definition.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I want to move some dp link training helpers into this place, so in
the future this won't be just about i2c any longer.
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Dave Airlie <airlied@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the cached EDID from intel_dp and intel_lvds_connector to
intel_connector. Unify cached EDID handling for LVDS and eDP, in
preparation for adding more generic EDID caching later.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The caller, not intel_connector_update_modes(), should free the edid. This
improves the reusability of intel_connector_update_modes().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pave the way for sharing some logic between eDP and LVDS.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Create a generic struct intel_panel for sharing a data structure and code
between eDP and LVDS panels. Add the new struct to intel_connector so that
later on we can have generic EDID and mode reading functions with EDID
caching that transparently fallback to fixed mode when EDID is not
available.
Add intel_panel as a dummy first, and move data (such as the mentioned
fixed mode) to it in later patches.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: Fixup tiny conflict in intel_dp_destroy.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Since we do EDID caching in intel_dp_init, we can do the fixed mode
initialization there too. This should not change the functionality apart
from initializing fixed mode earlier. Particularly retain the behaviour of
only falling back to VBT if EDID is not available to not regress
commit 47f0eb2234
Author: Keith Packard <keithp@keithp.com>
Date: Mon Sep 19 14:33:26 2011 -0700
drm/i915: Only use VBT panel mode on eDP if no EDID is found
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As there is 1:1 mapping between encoder and connector for the LVDS, the
goal is to simply reduce the amount of noise within the connector
functions, i.e. we split the encoder/connector for LVDS as best we can and
try to only operate on the LVDS connector from the connector funcs and the
LVDS encoder form the encoder funcs.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Get rid of saved int_lvds_connector and int_edp_connector in
drm_i915_private.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Introduce a local structure to move LVDS specific information away from the
drm_i915_private and onto the LVDS connector.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In preparation for introducing intel_lvds_connector to move some of the
LVDS specific storage away from drm_i915_private, first rename the encoder
to avoid potential confusion.
Based on earlier work by Chris Wilson <chris@chris-wilson.co.uk>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQgvdwAAoJEHm+PkMAQRiG+3AH/i2XsqqN3VctL0nnbWfvds+Q
aKulfIdJTjKiVAsawPUtRqReZ8ijiebrgA/53lZLlrFOoPPQ5+LHmnSyQF6gErOY
NuAE1lijXDRM1pwBlhvOBbAj26wUobGjqONFJ9OkKr758Ue8ds/Q7UdxyEgmYgmg
tvVMzfRcICzryUV3PcqL+3cNPpCUdT6wGGRJ9DCv/jvGiWKExWhOle5oltrmxk+D
NsqRcws5pEubfHE4J8BvNWr8lE1kHfYVhrJETiLJUiN2XAJcbI4Jy7rU/3EGteNS
0HMZdaPPjV874lohdM70X2225SbYrCVkAYB5hnZCTeC3tYyCawBBPMQoyAiOcmU=
=+861
-----END PGP SIGNATURE-----
Merge tag 'v3.7-rc2' into drm-intel-next-queued
Linux 3.7-rc2
Backmerge to solve two ugly conflicts:
- uapi. We've already added new ioctl definitions for -next. Do I need to say more?
- wc support gtt ptes. We've had to revert this for snb+ for 3.7 and
also fix a few other things in the code. Now we know how to make it
work on snb+, but to avoid losing the other fixes do the backmerge
first before re-enabling wc gtt ptes on snb+.
And a few other minor things, among them git getting confused in
intel_dp.c and seemingly causing a conflict out of nothing ...
Conflicts:
drivers/gpu/drm/i915/i915_reg.h
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_dp.c
drivers/gpu/drm/i915/intel_modes.c
include/drm/i915_drm.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fixes from Ben, off note:
ACPI ROM regression fix,
some IGP and AGP regressions fixes from rework fallout.
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/clock: fix missing pll type/addr when matching default entry
drm/nouveau/fb: fix reporting of memory type on GF8+ IGPs
drm/nv41/vm: don't init hw pciegart on boards with agp bridge
drm/nouveau/bios: fetch full 4KiB block to determine ACPI ROM image size
drm/nouveau: validate vbios size
drm/nouveau: warn when trying to free mm which is still in use
drm/nouveau: fix nouveau_mm/nouveau_mm_node leak
drm/nouveau/bios: improve error handling when reading the vbios from ACPI
drm/nouveau: handle same-fb page flips
This issue is a regression from 70790f4f81,
and causes us to miss a special-case for C51 (NV4E) chipsets and return
the wrong reference frequency for the VPLLs.
Should fix fdo#56202
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Without checking, we could detect vbios size as 0, allocate 0-byte array
(kmalloc returns invalid pointer for such allocation) and crash in
nouveau_bios_score while checking for vbios signature.
Reported-by: Heinz Diehl <htd@fritha.org>
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
It's questionable use case, but weston/wayland already relies on this
behaviour, and other drivers don't care about it, so it's a matter of
compatibility. Without it, process invoking such page flip hangs in
unkillable state, trying to reserve the same buffer twice.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Daniel writes:
The big thing is the disabling of the hsw support by default, cc: stable.
We've aimed for basic hsw support in 3.6, but due to a few bad
happenstances we've screwed up and only 3.8 will have better modeset
support than vesa. To avoid yet another round of fallout from such a
gaffle on for the next platform we've added a module option to disable
early hw support by default. That should also give us more flexibility in
bring-up.
Otherwise just small fixes:
- 3 fixes from Egbert for sdvo corner cases
- invert-brightness quirk entry from Egbert
- revert a dp link training change, it regresses some setups
- and shut up a spurious WARN in our gem fault handler.
- regression fix for an oops on bit17 swizzling machines, introduce in 3.7
- another no-lvds quirk
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Initialize obj->pages before use by i915_gem_object_do_bit17_swizzle()
drm/i915: Add no-lvds quirk for Supermicro X7SPA-H
drm/i915: Insert i915_preliminary_hw_support variable.
drm/i915: shut up spurious WARN in the gtt fault handler
Revert "drm/i915: Try harder to complete DP training pattern 1"
DRM/i915: Restore sdvo_flags after dtd->mode->dtd Roundrtrip.
DRM/i915: Don't clone SDVO LVDS with analog.
DRM/i915: Add QUIRK_INVERT_BRIGHTNESS for NCR machines.
DRM/i915: Don't delete DPLL Multiplier during DAC init.
We were programming register 0x42020 twice on those platforms. Once
should be enough.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the consolidated registers, it appears that we're setting the same
bis several times. Let's just collect the bits we want to set and program
it once.
v2: More cleanup. Also program 0x42004 and 0x45000 for FBC on non
mobile platforms (Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
[danvet: Undo the functional change as discussed on irc.]
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If we leave obj->pages set to NULL before attempting to deswizzle them,
then an OOPS is well deserved.
Fixes regression introduced in commit 9da3da660d
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jun 1 15:20:22 2012 +0100
drm/i915: Replace the array of pages with a scatterlist
Reported-and-tested-by: Krzysztof Kolasa
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reported-and-tested-by: Francois Tigeot <ftigeot@wolfpond.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=55375
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Register 0x42020 was defined twice under the names PCH_DSPCLK_GATE_D and
ILK_DSPCLK_GATE. This patch consolidate the 2 sets of defines in one.
The transforms done are:
PCH_DSPCLK_GATE_D -> ILK_DSPCLK_GATE_D
ILK_DSPCLK_GATE -> ILK_DSPCLK_GATE_D
DPARBUNIT_CLOCK_GATE_DISABLE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
ILK_DPARB_CLK_GATE -> ILK_DPARBUNIT_CLOCK_GATE_DISABLE
DPFDUNIT_CLOCK_GATE_DISABLE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_DPFD_CLK_GATE -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
ILK_CLK_FBC -> ILK_DPFDUNIT_CLOCK_GATE_DISABLE
DPFCRUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS1 -> ILK_DPFCRUNIT_CLOCK_GATE_DISABLE
DPFCUNIT_CLOCK_GATE_DISABLE -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
ILK_DPFC_DIS2 -> ILK_DPFCUNIT_CLOCK_GATE_DISABLE
We have a VHRUNIT_CLOCK_GATE_DISABLE define for the pre-ILK DSPCLK_GATE_D.
Even if the same bit is used in ILK_DSPCLK_GATE_D, other bits in the
register change, so I went with re-defining it, well more precisely rename
IVB_VRHUNIT_CLK_GATE, which is not specific to IVB+. So:
IVB_VRHUNIT_CLK_GATE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE
VHRUNIT_CLOCK_GATE_DISABLE -> ILK_VHRUNIT_CLOCK_GATE_DISABLE (ILK+ code)
This commit is only a renaming commit, further commits will clean up the
logic.
v2: Rename bit 5 and 7 to _ENABLE as setting them to 1 enables clock
gating on their respective units, contrary to all of the other bits
(Paulo Zanoni)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Single-threaded forcewake was only used on some early pre-production
ivybridge machines, all the latest ones should use mt forcewake. And
we already assume this in other places of the code (e.g. DERRMR
support in the ddx, or the latest intel_gt_reset patch to reset any
lingering forcewake references left behind by the bios), so don't
bother here, too.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is the final remaining piece of Haswell DP enablement. After this
patch, just calling intel_dp_init on any port will make DP work. We
still do not do this because we're currently initializing HDMI on all
the ports, so if we replace intel_hdmi_init with intel_dp_init, we
will break HDMI, and we can't call both because they share the same
registers.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previous patch "drm/i915: add basic Haswell DP link train bits"
implemented the basic structure to set the voltage levels and training
patterns. This patch adds the higher-level bits that are part of the
mode set sequence and hot plug.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have to write the correct values inside intel_dp_set_m_n and then
prevent these values from being overwritten later.
V2: Unconfuse double negation.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Just a missing register. There is no problem to run this code when the
output is HDMI.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should only write the DDI_BUF_CTL at this point for HDMI/DVI. For
DP we need to do this earlier, and the values written to the register
are also different.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The old rule that the AUX registers are just an offset (+4 and +10)
from output_reg is not true anymore, since output_reg in on the CPU
and some AUX regs are on the PCH.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: use the existing #defines as spotted by Damien Lespiau.]
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some BIOSes may forcibly suspend RC6 during their operation which
trigger a warning as we find the hardware in a perplexing state upon
first use. So far that appears to be the worst symptom as fortuituously
we use the same values as the BIOS for programming the FORCEWAKE register.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now no longer rely on this.
This is step 1 on a long journey to rid us of the save/restore
madness, which tends to lightly paper over many issues, and cause
tons of bad things itself ...
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: satisfy Paulo's ocd and drop the needless braces.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... instead of relying on the register save/restore madness to do this.
To extract a bit of code call drm_mode_config_reset both on resume
and boot-up and move the hw state frobbing from the crt_init to the
->reset callback. The crt connector is the only one with a ->reset
callback, hence we can easily do this.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
... since they don't apply to pre-pch platforms and could actually be
harmful.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already do that as part of the ringbuffer re-setup at resume time.
Furthermore the register offset has moved on gen6+ around quite a bit,
and on ilk/gm45 we also need to restore the HWS reg for the bsd ring,
not just the render ring.
So again in kms mode this is only confusing a best, hence don't
bother.
v2: Fixup logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We already call drm_irq_install/uninstall at the right time, which
will set up the irq registers with the correct values (through the
preinstall hooks).
For kms this is at best harmless, in the worst case we get an
interrupt when we don't really expect it.
v2: Fixup the logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We completely compute these anew in each modeset, hence we don't rely
on them containing anything valid after resume.
To avoid breaking any ums setup due to reordering of the reads/writes
simply don't reorder anything, but bracket the reads/writes into if
(!kms) conditionals. More churn, but safer.
v2: Fixup the logic, noticed by Paulo Zanoni.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Much simpler and looks more like the M/N code inside intel_display.c.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously, the DP register was used for everything. On Haswell, it
was split into DDI_BUF_CTL (which is the new intel_dp->DP register)
and DP_TP_CTL.
The logic behind this patch is based on a patch written by Shobhit
Kumar, but the way the code was written is very different.
Credits-to: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: Fixup the logic error spotted by Jani Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In theory, all the DDI pipe settings should be set here, including
timing and M/N registers. For now, let's just set the DP MSA
attributes.
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
[danvet: fixed up the unused typo in a #define, spotted by Jani
Nikula.]
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On the worst scenario, users with new hardwares and old kernel from
enabling times can get black screens. So, from now on, this
perliminary_hw_support module parameter shall be used by all upcoming
platforms that are still under enabling. The second option would be to
merge the pci ids after basic modeset works, but that makes testing
and development while bringing up hw a rather tedious afair.
Although it is uncomfortable for developers use this extra variable it
brings more stability for end users.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Reviewed-by: Dave Airlie <airlied@redhat.com>
[danvet: dropped the i915_ param prefix, i915.i915_ is just tedious.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional change, but reserves 0x2 for use by userspace.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With the introduction of per-process GTT space, the hardware designers
thought it wise to also limit the ability to write to MMIO space to only
a "secure" batch buffer. The ability to rewrite registers is the only
way to program the hardware to perform certain operations like scanline
waits (required for tear-free windowed updates). So we either have a
choice of adding an interface to perform those synchronized updates
inside the kernel, or we permit certain processes the ability to write
to the "safe" registers from within its command stream. This patch
exposes the ability to submit a SECURE batch buffer to
DRM_ROOT_ONLY|DRM_MASTER processes.
v2: Haswell split up bit8 into a ppgtt bit (still bit8) and a security
bit (bit 13, accidentally not set). Also add a comment explaining why
secure batches need a global gtt binding.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk> (v1)
[danvet: added hsw fixup.]
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Somehow this was left out in the refactoring that introduced the pch
handlers. Avoids a hotplug_mask special case in the ilk_irq_handler.
Noticed while hunting down the pch hotplug bits.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-ENOSPC can happen if userspace is being simplistic and tries to map a
too big object. To aid further spurious WARN debugging, also print out
the error code.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=56017
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 2477367083.
If (for whatever reason) the DP sink device never asks for the maximal
voltage level, we never don't hit the check that should bail us out
after 5 retries of the same voltage. Which leads to an endless loop in
the DP link training code, which hangs the driver.
Now some more DP link training experiments on eDP panels seem to
indicate that our training algorithm isn't robust enough anyway and
needs more work. Hence for 3.7-fixes, let's just revert the regressing
commit instead of trying to apply more duct-tape.
Reported-by: Oleksij Rempel <bug-track@fisher-privat.net>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For TV and LVDS encoders intel_sdvo_set_input_timings_for_mode()
is called to pass a mode to the sdvo chip and retrieve a dtd
containing information needed to calculate the adjusted_mode which
is done by intel_sdvo_get_dtd_from_mode().
To set this adjusted_mode as input mode for the sdvo chip, a dtd is
recalculated using intel_sdvo_get_mode_from_dtd(). During this round
trip the sdvo_flags contained in the dtd obtained from the hardware
are lost.
Since these flags cannot be ignored in all cases this patch preserves
and restores them.
This regression has been introduced in
commit 6651819b4b
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Apr 1 19:16:18 2012 +0200
drm/i915: handle input/output sdvo timings separately in mode_set
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SDVO LVDS are not clonable as the input mode gets adjusted by
the LVDS encoder.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
NCR machines with LVDS panels using Intel chipsets need to have the
QUIRK_INVERT_BRIGHTNESS bit set.
Unfortunately NCR doesn't set a meaningful subvendor/subdevice ID,
therefore we add a DMI dependent quirk list.
Signed-off-by: Egbert Eich <eich@suse.de>
[danvet: fixup whitespace fail.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DPLL multipiler is set up in intel_display.c:i9xx_update_pll()
called from i9xx_crtc_mode_set().
There the DPLL multiplier is adjusted so that the SDVO gets a sufficient
bus clock.
When cloning a CRTC between an SDVO driven encoder and the standard
DAC the DAC setup code reseted the multiplier value to 1 thus undoing
the correct setup. There is no need to touch the multiplier in the DAC
setup code: the correct value (i.e. 1 in case no SDVO encoder is used)
is set by i9xx_update_pll() already.
A comment at the code suggested that this code is a left over from the
days when there was no setup for clone modes.
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS should be setting the minimum voltage for rc6 to be 450mV. Old or
buggy BIOSen may not be doing this, so we correct it for them. Ideally
customers should update the BIOS as only it would know the optimal
values for the platform, so we leave that fact as a DRM_ERROR for the
user to see.
Unfortunately this isn't fixing any of the issues it was targeted to
fix, but it is documented that we must do it.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Matt Turner <mattst88@gmail.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: bikeshedded loglevel of the "your bios is broken message" to
debug.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There is a special mechanism for communicating with the PCU already
being used for the ring frequency stuff. As we'll be needing this for
other commands, extract it now to make future code less error prone and
the current code more reusable.
I'm not entirely sure if this code matches 1:1 with the previous code
behaviorally. Functionally however, it should be the same.
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Fixup compile fail reported by Wu Fengguang.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
minor set of nouveau fixes.
* 'drm-nouveau-fixes' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
drm/nouveau/bios: fix typo in error message
drm/nouveau: only call ttm_agp_tt_create when __OS_HAS_AGP
drm/nv50/fb: fix double free of vram mm
drm/nouveau/pm: do not stop reclocking if failing to set the fan speed
drm/nouveau/pm: fix a typo related to the move to the therm subdev
drm/nouveau/hwmon: fix the initialization condition
ttm_agp_tt_create is itself defined under CONFIG_AGP, so there's no
point calling it otherwise.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nouveau_fb_destroy already calls nouveau_mm_fini on vram mm.
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
With the introduction of fan management modes, fan may not be drivable.
We should allow reclocking nonetheless.
This return was stupid to begin with since it may have left the card
in an intermediate state (clocks corresponding to a perflvl and voltage
corresponding to another one). The reclocking code will need to be
rewritten in a near-future in order to provide a better error handling.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Reported-by: Vekin on IRC
Reported-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Martin Peres <martin.peres@labri.fr>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drivers/gpu/drm/radeon/radeon_atpx_handler.c:151:3: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'size_t'
[airlied: Alex had others fixed already, except for atpx one]
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Alex writes:
"This is the first -fixes pull for 3.7. I would have preferred
to have gotten it out a bit sooner, but I was on holiday last week.
- Cleanup of the new 2 level page table code it get it in
better shape and using less memory.
- Fix some display issues related to the PLL rework.
- Fix some cmpiler warnings and errors with certain config
options.
- Other misc bug fixes."
* 'drm-fixes-3.7' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix spelling typos in debugging output
drm/radeon: Don't destroy I2C Bus Rec in radeon_ext_tmds_enc_destroy().
drm/radeon: check if pcie gen 2 is already enabled (v2)
drm/radeon/cayman: set VM max pfn at MC init
drm/radeon: separate pt alloc from lru add
drm/radeon: don't add the IB pool to all VMs v2
drm/radeon: allocate page tables on demand v4
drm/radeon: update comments to clarify VM setup (v2)
drm/radeon: allocate PPLLs from low to high
drm/radeon: fix compilation with backlight disabled
drm/radeon: use %zu for formatting size_t
Daniel writes:
"- some register magic to fix hsw crw (Paulo&Ben)
- fix backlight destruction for cpu edp (Jani)
- fix gen ch7xxx dvo ->get_hw_state
- fixup the plane->pipe fixup code, the broken version massively angers
the modeset sanity checks
- kill pipe A quirk for i855gm, otherwise I get a black screen with the
above patch
- fixup for gem_get_page helper (Chris)
- fixup guardband clipping w/a (Ken), without this mesa master can erronously
drop vertices on snb, mesa 9.0 has the optimization reverted
- another pageflip vs. modeset fix
- kill bogus BUG_ON which broke ums+gem from Willy Tarreau (gasp, people
are still using this!)"
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: fix non-DP-D eDP backlight cleanup and module reload
drm/i915: HSW CRW stability magic
drm/i915/dvo-ch7xxx: fix get_hw_state
drm/i915: fixup the plane->pipe fixup code
drm/i915: rip out the pipe A quirk for i855gm
drm/i915: disable wc gtt pte mappings on gen2
drm/i915: fixup i915_gem_object_get_page inline helper
drm/i915: Disallow preallocation of requests
drm/i915: Set guardband clipping workaround bit in the right register.
drm/i915: paper over a pipe-enable vs pageflip race
drm/i915: remove useless BUG_ON which caused a regression in 3.5.
radeon_i2c_fini() walks thru the list of I2C bus recs rdev->i2c_bus[]
to destroy each of them.
radeon_ext_tmds_enc_destroy() however also has code to destroy it's
associated I2C bus rec which has been obtained by radeon_i2c_lookup()
and is therefore also in the i2c_bus[] list.
This causes a double free resulting in a kernel panic when unloading
the radeon driver.
Removing destroy code from radeon_ext_tmds_enc_destroy() fixes this
problem.
agd5f: fix compiler warning
Signed-off-by: Egbert Eich <eich@suse.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
No need to emit them at VM flush as we no longer use
variable sized page tables now that we support 2 level
page tables. This matches the behavior of SI (which
does not support variable sized page tables).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Make it possible to allocate a persistent page table.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We want to use VMs without the IB pool in the future.
v2: also remove it from radeon_vm_finish.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Based on Dmitries work, but splitting the code into page
directory and page table handling makes it far more
readable and (hopefully) more reliable.
Allocations of page tables are made from the SA on demand,
that should still work fine since all page tables are of
the same size.
Also using the fact that allocations from the SA are mostly
continuously (except for end of buffer wraps and under very
high memory pressure) to group updates send to the chipset
specific code into larger chunks.
v3: mostly a rewrite of Dmitries previous patch.
v4: fix some typos and coding style
Signed-off-by: Dmitry Cherkasov <Dmitrii.Cherkasov@amd.com>
Signed-off-by: Christian König <deathsimple@vodafone.de>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The actual set up and assignment of VM page tables
is done on the fly in radeon_gart.c.
v2: update vm size comments
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
The order shouldn't matter, but there have been problems
reported on certain older asics. This behaves more
like the original code before the PPLL allocation
rework.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Markus Trippelsdorf <markus@trippelsdorf.de>
