Commit Graph

20058 Commits

Author SHA1 Message Date
Todd Previte
74ebf294a1 drm/i915: Add a delay in Displayport AUX transactions for compliance testing
The Displayport Link Layer Compliance Testing Specification 1.2 rev 1.1
specifies that repeated AUX transactions after a failure (no response /
invalid response) must have a minimum delay of 400us before the resend can
occur. Tests 4.2.1.1 and 4.2.1.2 are two tests that require this specifically.

Also, the check for DP_AUX_CH_CTL_TIME_OUT_ERROR has been moved out into a
separate case. This case just continues with the next iteration of the loop
as the HW has already waited the required amount of time.

V2:
- Changed udelay() to usleep_range()
V3:
- Removed extraneous check for timeout
- Updated comment to reflect this change
V4:
- Reformatted a comment
V5:
- Added separate check for HW timeout on AUX transactions. A message
  is logged upon detection of this case.
V6:
- Add continue statement to HW timeout detect case
- Remove the log message indicating a timeout has been
  detected (review feedback)
V7:
- Updated the commit message to remove verbage about the HW timeout
  case that is no longer valid.

Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 13:31:46 +02:00
Todd Previte
c5d5ab7a05 drm/i915: Add automated testing support for Displayport compliance testing
Add the skeleton framework for supporting automation for Displayport compliance
testing. This patch adds the necessary framework for the source device to
appropriately respond to test automation requests from a sink device.

V2:
- Addressed previous mailing list feedback
- Fixed compilation issue (struct members declared in a later patch)
- Updated debug messages to be more accurate
- Added status checks for the DPCD read/write calls
- Removed excess comments and debug messages
- Fixed debug message compilation warnings
- Fixed compilation issue with missing variables
- Updated link training autotest to ACK

V3:
- Fixed the checks on the DPCD return code to be <= 0
  rather than != 0
- Removed extraneous assignment of a NAK return code in the
  DPCD read failure case
- Changed the return in the DPCD read failure case to a goto
  to the exit point where the status code is written to the sink
- Removed FAUX test case since it's deprecated now
- Removed the compliance flag assignment in handle_test_request

V4:
- Moved declaration of type_type here
- Removed declaration of test_data (moved to a later patch)
- Added reset to 0 for compliance test variables

V5:
- Moved test_active variable declaration and initialization out of
  this patch and into the patch where it's used
- Changed variable name compliance_testing_active to
  compliance_test_active to unify the naming convention
- Added initialization for compliance_test_type variable

Signed-off-by: Todd Previte <tprevite@gmail.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 13:26:43 +02:00
kbuild test robot
b3f9d7d7bc drm/i915: fix semicolon.cocci warnings
drivers/gpu/drm/i915/i915_debugfs.c:4850:2-3: Unneeded semicolon

 Removes unneeded semicolon.

Generated by: scripts/coccinelle/misc/semicolon.cocci

CC: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 12:59:57 +02:00
Daniel Vetter
5829975ce0 drm/i915/dp: Remove intel_ prefix from hw signal_levels functions
intel_ is for generic code bxt_ and friends for platform specific
functions. Remove the intel_ prefix to be consistent with our naming.

Random OCD bikeshed I've spotted while merging bxt patches.

v2: Oops, git add fail.

Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-04-16 11:47:50 +02:00
Vandana Kannan
9314726b9f drm/i915/bxt: Update max level of vswing
Broxton supports 3 voltage swing levels on all DP ports.
Max level of pre-emphasis will be taken care with the existing code.

v2: Patch rebased

v3: (imre)
- keep existing behavior for other platforms
- clarify commit message

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:40 +02:00
Vandana Kannan
96fb9f9b15 drm/i915/bxt: VSwing programming sequence
VSwing programming sequence as specified in the updated BXT BSpec

v2: Satheesh's review comments addressed.
- clear value before setting into registers
- move print statement to bxt function
Other changes
- since signal level will not be set into DDI_BUF_CTL, the value need
  not be returned to intel_dp_set_signal_levels(). Making the bxt
  specific function to return void and setting signal_levels = 0 for
  bxt inside intel_dp_set_signal_levels()
- instead of signal levels, printing vswing level and pre-emphasis
  level
- in case none of the pre-emphasis levels or vswing levels are set,
  setting default of 400mV + 0dB

v3: Satheesh's review comments
- Check for mask before printing signal_levels.
- Removing redundant register writes
- Call intel_prepare_ddi_buffers only for HAS_PCH_SPLIT
- Making register write part generic as it will be required for HDMI as
  well.

Re-structure the code to include an array for vswing related values, set
signal levels

v4: Satheesh's review comments
- Rebase over latest renaming patches
- use hsw_signal_levels for HAS_DDI
Other changes
- Modified vswing_sequence() func definition
- Rebased on top of register macro definitions

v5: Satheesh's review comments
- Check ddi translation table size

v6: Imre's review comments
- removed comments in vswing sequence
- added vswing, pre-emphasis prints in intel_dp_set_signal_levels
- added comment explaining use of DP vswing values for eDP
- initialize n_entries and ddi_transaltion table based on encoder type
- create bxt_ddi_buf_trans structure and use decimal values
- adding a flag in bxt buffer translation table to indicate def entry

v7: (imre)
- squash in Vandana's "VSwing register definition",
  "HDMI VSwing programming", "Re-enable vswing programming",
  "Fix vswing sequence" patches
- use BXT_PORT_* regs directly instead of via a temp var
- simplify BXT_PORT_* macro definitions
- add code comment why we read lane while write group registers
- fix readout of DP_TRAIN_PRE_EMPHASIS in debug message

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v6)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:39 +02:00
Damien Lespiau
ce3b7e9bcf drm/i915: Don't write the HDMI buffer translation entry when not needed
We don't actually need to write the HDMI entry on DDIs that have no
chance to be used as HDMI ports.

While this patch shouldn't change the current behaviour, it makes
further enabling work easier as we'll have an eDP table filling the full
10 entries.

v2: Rely on the logic from intel_ddi_init() to figure out if the DDI port
    supports HDMI or not (Paulo).

Suggested-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:39 +02:00
Damien Lespiau
b403745c84 drm/i915: Iterate through the initialized DDIs to prepare their buffers
Not every DDIs is necessarily connected can be strapped off and, in the
future, we'll have platforms with a different number of default DDI
ports. So, let's only call intel_prepare_ddi_buffers() on DDI ports that
are actually detected.

We also use the opportunity to give a struct intel_digital_port to
intel_prepare_ddi_buffers() as we'll need it in a following patch to
query if the port supports HMDI or not.

On my HSW machine this removes the initialization of a couple of
(unused) DDIs.

Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:38 +02:00
Imre Deak
503604038b drm/i915: suppress false PLL state warnings on non-GMCH platforms
The checks for PLL enabled state on CPU ports are valid only on GMCH
platforms but atm we'd also call them on non-PCH-split/non-GMCH
platforms like BXT, triggering false warnings. Until the proper check is
implented for these platforms simply disable the check.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:38 +02:00
Satheeshakrishna M
977bb38d2d drm/i915/bxt: Determine programmed frequency
Add placeholder function for calculating programmed pixel clock.
Note: Formula to back calculate link clock from dividers not
available currently.

v2:
- rebased on upstream s/crtc_config/crtc_state/ change (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:37 +02:00
Satheeshakrishna M
3760b59cba drm/i915/bxt: Determine PLL attached to pipe
Determine PLL attached to pipe (which is same as DDI PLL)

v2:
- rebased on upstream s/crtc_config/crtc_state/ (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:37 +02:00
Satheeshakrishna M
bcddf61077 drm/i915/bxt: Assign PLL for pipe
Assign PLL for pipe (dependent on port attached to the pipe)

v2:
- fix incorrect encoder vs. new_encoder check for crtc (imre)

v3:
- warn and return error if no encoder is attached (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Don't move intel_ddi_get_crtc_new_encoder around.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:42:36 +02:00
Satheeshakrishna M
d683f3bc48 drm/i915/bxt: BXT clock divider calculation
Calculate and cache clock parameters. Follow bspec algorithm for HDMI.
Use precalculated values for DisplayPort linkrates.

v2: (imre)
- rebase against upstream crtc_state change
- use the existing CHV based helper instead of handrolling the same

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:29:07 +02:00
Imre Deak
5ab7b0b71e drm/i915/bxt: add bxt_find_best_dpll
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:29:07 +02:00
Satheeshakrishna M
dfb8240847 drm/i915/bxt: Define bxt DDI PLLs and implement enable/disable sequence
Plug bxt PLL code into existing shared DPLL framework.

v2: (imre)
- squash in Satheeshakrishna's "Define BXT clock registers" and
  "Add state variables for bxt clock registers" patches
- squash in Vandanas's "Change grp access to lane access for PLL"
- fix group vs. lane access in bxt_ddi_pll_get_hw_state
- add code comment why we read from lane registers while writing to
  group registers
- clean up register macros
- use BXT_PORT_PLL_* macros instead of open-coding the same
- check if BXT_PORT_PCS_DW12_LN01 matches BXT_PORT_PCS_DW12_LN23
  during hardware state readout
- add missing LANESTAGGER_STRAP_OVRD masking
- add note about missing step according to the latest BUN for
  PORT_PLL_9/lockthresh

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:29:06 +02:00
Jesse Barnes
ff6d9f55fe drm/i915/bxt: fix panel fitter setup in crtc disable/enable
Broxton has the same panel fitter registers as Skylake.

v2:
- add MISSING_CASE for future platforms (daniel)

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:29:06 +02:00
Satheeshakrishna M
1ab23380f8 drm/i915/bxt: Restrict PORT_CLK_SEL programming below gen9
PORT_CLK_SEL programming is needed only on HSW/BDW.

v2:
- don't program PORT_CLK_SEL from mst encoders either (imre)
v3:
- fix the check for GEN9+ in intel_mst_pre_enable_dp() (damien)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:29:05 +02:00
Jesse Barnes
535afa2e9e drm/i915/vlv: check port in infoframe_enabled v2
Same as IBX and G4x, they all share the same genetic material.

v2: we all need a bit more port in our lives

Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:30 +02:00
Chris Wilson
baaa5cfb42 drm/i915: Update meaning of debugfs object's pin_flag
Since the pin_ioctl is defunct, we only care about whether an object is
pinned into the display for debug purposes.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:30 +02:00
Chris Wilson
1f30a61482 drm/i915: Simplify i915_gem_obj_is_pinned() test for set-tiling
Since the removal of the user pin_ioctl, the only means for pinning an
object is either through binding to the scanout or during execbuf
reservation. As the later prevents a call to set-tiling, we need only
check if the obj is pinned into the display plane to see if we need
reject the set-tiling ioctl.

Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:29 +02:00
Sonika Jindal
b7192a567c drm/i915/skl: Add back HDMI translation table
The HDMI translation table is added back to bspec, so adding it,
and defaulting the 800mV+0dB entry.

The HDMI translation table was removed by following commit as per HW team's
recommendation:
commit 7ff446708b ("drm/i915/skl: Only use the 800mV+2bB HDMI translation entry")

v2: Adding reference to commit which removed this table (Jani)

Cc: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:29 +02:00
Daniel Vetter
8805aa713e drm/i915: Drop unecessary fb arguments from function signatures
This is a separate patch to simplify conflict handling with other
ongoing atomic work.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:28 +02:00
Daniel Vetter
d328c9d78d drm/i915: Select starting pipe bpp irrespective or the primary plane
Since universal planes the primary plane might not be around, and it's
kinda silly to restrict the pipe bpp to the primary plane if we might
end up displaying a 10bpc video overlay. And with atomic we might very
well enable a pipe without a primary plane. So just use the platform
max as a starting point and then restrict appropriately.

Of course this is all still a bit moot as long as we artificially
compress everything to max 8bpc because we don't use the hi-bpc gamma
tables.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:28 +02:00
Tvrtko Ursulin
5678ad7367 drm/i915: Fix view type in warning message
One month passed between posting a patch and it getting merged, and
unfortunately even though it still applies, it needs fixing to account
for changes in function parameters since:

   commit d385612e15b8b6eb3db328d83f1872ef8a381788
   Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
   Date:   Tue Mar 17 14:45:29 2015 +0000

       drm/i915: Log view type when printing warnings

Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
[danvet: Squash in fixup from Tvrtko to fix the rebase conflict.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 11:20:07 +02:00
Suketu Shah
31335cec02 drm/i915/bxt: Add DC9 Trigger sequence
Add triggers for DC9 as per details provided in bxt_enable_dc9
and bxt_disable_dc9 implementations.

v1:
- Add SKL check in gen9_disable_dc5 as it is possible for DC5
  to remain disabled only for SKL.
- Add additional checks for whether DC5 is already disabled during
  DC5-disabling only for BXT.

v2:
- rebase to latest.
- Load CSR during DC9 disabling in the beginning before DC9 is
  disabled.
- Make gen9_disable_dc5 function non-static as it's being called by
  functions in i915_drv.c.
- Enable DC9-related functionality using a macro.

v3: (imre)
- remove BXT_ENABLE_DC9, we want DC9 always, and it's only valid on BXT
- remove DC5 disabling and CSR FW loaded check, these are nop atm
- squash in Vandana's "Do ddi_phy_init always" patch

v4:
- add TODO to re-enable DC5 during resume if CSR FW is available (sagar)

Signed-off-by: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:27:17 +02:00
A.Sunil Kamath
664326f8a5 drm/i915/bxt: Implement enable/disable for Display C9 state
v2: Modified as per review comments from Imre
- Mention enabling instead of allowing in the debug trace and
  remove unnecessary comments.

v3:
- Rebase to latest.
- Move DC9-related functions from intel_display.c to intel_runtime_pm.c.

v4: (imre)
- remove DC5 disabling, it's a nop at this point
- squashed in Suketu's "Assert the requirements to enter or exit DC9"
  patch
- remove check for RUNTIME_PM from assert_can_enable_dc9, it's not a
  dependency

Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com> (v3)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Sagar Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:20:16 +02:00
Imre Deak
eee215660c drm/i915/bxt: add description about the BXT PHYs
Extend the VLV/CHV DPIO (PHY) documentation with the BXT specifics.

v2:
- add more detail about the mapping between ports and transcoders (ville)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:20:15 +02:00
Vandana Kannan
5c6706e564 drm/i915/bxt: add display initialize/uninitialize sequence (PHY)
Add PHY specific display initialization sequence as per BSpec.

Note that the PHY initialization/uninitialization are done
at their current place only for simplicity, in a future patch - when more
of the runtime PM features will be enabled - these will be moved to
power well#1 and modeset encoder enabling/disabling hooks respectively.

The call to uninitialize the PHY during system/runtime suspend will be
added later in this patchset.

v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set

v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- fix DDI PHY timeout value
- squash in Vandana's "PORT_CL2CM_DW6_A BUN fix",
  "DDI PHY programming register defn", "Do ddi_phy_init always",
- move PHY register macros next to the corresponding CHV/VLV macros
- move DE PLL register macros here from another patch since they are
  used here first
- add BXT_ prefix to CDCLK flags
- s/COMMON_RESET/COMMON_RESET_DIS/ and clarify related code comments
- fix incorrect read value for the RMW of BXT_PHY_CTL_FAMILY_DDI
- fix using GT_DISPLAY_EDP_POWER_ON vs. GT_DISPLAY_DDI_POWER_ON
  when powering on DDI ports
- fix incorrect port when setting BXT_PORT_TX_DW14_LN for DDI ports
- add missing masking when programming CDCLK_FREQ_DECIMAL
- add missing powering on for DDI-C port, rename OCL2_LDOFUSE_PWR_EN
  to OCL2_LDOFUSE_PWR_DIS to reduce confusion
- add note about mismatch with bspec in the PORT_REF_DW6 fields
- factor out PHY init code to a new function, so we can call it for
  PHY1 and PHY0, instead of open-coding the same

v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
  accordingly
- use the existing dpio_phy enum instead of adding a new one for the
  same purpose
- flip the meaning of PHYs so that PHY_A is PHY1 and PHY_BC is PHY0 to
  better match CHV
- s/BXT_PHY/_BXT_PHY/
- use _PIPE for _BXT_PHY instead of open-coding it
- drop _0_2_0_GTTMMADR suffix from BXT_P_CR_GT_DISP_PWRON
- define GT_DISPLAY_POWER_ON in a more standard way
- make a note that the CHV ConfigDB also disagrees about GRC_CODE field
  definitions
- fix lane optimization refactoring fumble from v3
- add per PHY uninit functions to match the init counterparts

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:20:15 +02:00
Vandana Kannan
f8437dd1b5 drm/i915/bxt: add display initialize/uninitialize sequence (CDCLK)
Add CDCLK specific display clock initialization sequence as per BSpec.

Note that the CDCLK initialization/uninitialization are done at their
current place only for simplicity, in a future patch - when more of the
runtime PM features will be enabled - these will be moved to power
well#1 and modeset encoder enabling/disabling hooks respectively. This
also means that atm dynamic power gating power well #1 is effectively
disabled.

The call to uninitialize CDCLK during system/runtime suspend will be
added later in this patchset.

v1: Added function definitions in header files
v2: Imre's review comments addressed
- Moved CDCLK related definitions to i915_reg.h
- Removed defintions for CDCLK frequency
- Split uninit_cdclk() by adding a phy_uninit function
- Calculate freq and decimal based on input frequency
- Program SSA precharge based on input frequency
- Use wait_for 1ms instead 200us udelay for DE PLL locking
- Removed initial value for divider, freq, decimal, ratio.
- Replaced polling loops with wait_for
- Parameterized latency optim setting
- Fix the parts where DE PLL has to be disabled.
- Call CDCLK selection from mode set

v3: (imre)
- add note about the plan to move the cdclk/phy init to a better place
- take rps.hw_lock around pcode access
- move DE PLL register macros here from another patch since they are
  used here first
- add BXT_ prefix to CDCLK flags
- add missing masking when programming CDCLK_FREQ_DECIMAL

v4: (ville)
- split the CDCLK/PHY parts into two patches, update commit message
  accordingly
- s/DISPLAY_PCU_CONTROL/HSW_PCODE_DE_WRITE_FREQ_REQ/
- simplify BXT_DE_PLL_RATIO macros
- fix BXT_DE_PLL_RATIO_MASK
- s/bxt_select_cdclk_freq/broxton_set_cdclk_freq/
- move cdclk init/uninit/set code from intel_ddi.c to intel_display.c
- remove redundant code comments for broxton_set_cdclk_freq()
- sanitize fixed point<->integer frequency value conversion
- use DRM_ERROR instead of WARN
- do RMW when programming BXT_DE_PLL_CTL for safety
- add note about PLL lock timeout being exactly 200us
- make PCU error messages more descriptive
- instead of using 0 freq to mean PLL off/bypass freq use 19200
  for clarity, as the latter one is the actual rate
- simplify pcode programming, removing duplicated
  sandybridge_pcode_write() call
- sanitize code flow, remove unnecessary scratch vars in
  broxton_set_cdclk() (imre)
- Remove bound check for maxmimum freq to match current code.
  This check will be added later at a more proper platform
  independent place once atomic support lands.
- add note to remove freq guard band which isn't needed on BXT
- add note to reduce freq to minimum if no pipe is enabled
- combine broxton_modeset_global_pipes() with
  valleyview_modeset_global_pipes()

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:20:14 +02:00
Vandana Kannan
164dfd2877 drm/i915: Rename vlv_cdclk_freq to cdclk_freq
Rename vlv_cdclk_freq to cdclk_freq so that it can be used for all
platforms as required. Needed by the next patch.

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-16 09:20:13 +02:00
Rodrigo Vivi
c7240c3bc5 drm/i915: PSR VLV: Add single frame update.
According to spec: "In PSR HW or SW mode, SW set this bit before writing
registers for a flip. It will be self-clear when it gets to the PSR
active state."

Some versions of spec mention that this is needed when in
"Persistent mode" but define it as same as "SW mode". Since this
fix the page flip case let's assume this is exactly what we need.

Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 19:15:23 +02:00
Rodrigo Vivi
89251b177b drm/i915: PSR: deprecate link_standby support for core platforms.
On Haswell and Broadwell with link in standby when exit event happens
between vblank and VSC packet, PSR exit on panel but DPA transmitter
still sends black pixel. When this condition hits, panel will intermittently
display black frame.

The known W/A for this case involve the of single_frame update
that isn't supported on Haswell and to be supported on Broadwell
3 other workarounds would be required. So it is better and safe to
just deprecate link_standby for now.

Also, link fully off saves more power than link_standby and afwk
no OEM is requesting link standby on VBT. There is no reason for that.

For Skylake let's just consider it behaves like Broadwell until
we prove otherwise.

v2: Fix commit message (Durga).

v3: Fix conflict with PSR2.

Reference: HSD: bdwgfx/1912559
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 19:15:17 +02:00
Rodrigo Vivi
3301d40921 drm/i915: PSR: Fix DP_PSR_NO_TRAIN_ON_EXIT logic
Since the beginning there is a missunderstanding on the meaning of this
dpcd bit.
This bit shouldn't indicate whether to use link standby or not, but just
be used to configure TP1, TP2 and TP3 times and tell hw aux should be skiped
since HW is the responsible one.

Even with help of frontbuffer tracking, HW is still fully responsible for
PSR exit logic with/without DP training.

DP_PSR_NO_TRAIN_ON_EXIT means the source doesn't need to do the training, but
it doesn't tell to avoid TP patterns, so we will send minimal TP1 and avoid
TP2. It also means that sink itself can take up to 5 idle frames for training.
6 in our case since we might be off by 1. So we also increment idle_frames by 4
here.

v2: Fix and improve commit message (Durga).
v3: Use minimal TP1 time avoiding TP2 and increase idle frame.

Cc: Durgadoss R <durgadoss.r@intel.com>
Cc: Arthur Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 19:15:01 +02:00
Rodrigo Vivi
cff5190cb9 drm/i915: PSR: Remove wrong LINK_DISABLE.
This wrong logic and useless define came from first versions and
came along with all rework. Just now I notice how ugly, wrong and
useless this is.

val is already defined as 0 anyway and logic is completelly wrong
and useless. So let's starting the link_standby fix with this
cleaning.

Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 19:14:53 +02:00
Satheeshakrishna M
0b4a2a36d0 drm/i915/bxt: Define BXT power domains
Add BXT power domains

v2: Use DOMAIN_PLLS instead of a new CDCLK one, whitespace fixes
    (Damien)
v3: add VGA, TRANSCODER_A power domains (imre)

Signed-off-by: Satheeshakrishna M <satheeshakrishna.m@intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 15:05:47 +02:00
Shashank Sharma
9e63743ebb drm/i915/bxt: Enable GMBUS IRQ
GMBUS interrupt has been moved to CPU side in BXT.
What this patch does is:
1. Enable GMBUS IRQ in de_post_install function
2. Handle this interrupt as a port interrupt in display irq
   handler

v2: Rebase on top of the for_each_pipe() change adding dev_priv as
    first argument (Damien).
v3: read BXT_DE_PORT_GMBUS IIR flag only on BXT on other platforms
    it's reserved (imre)
v4: (jani)
- remove redundant 'BXT GMBUS' comment
- fix formatting of BXT_DE_PORT_GMBUS definition

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:53:04 +02:00
Shashank Sharma
266ea3d9c4 drm/i915/bxt: Add BXT support in gen8_irq functions
This patch adds conditional checks in gen8_irq functions
to support BXT. Most of the checks just look for PCH split
availability, and block the call to PCH interrupt functions if
not available.

v2: (jani)
- drop redundant TODO comment about PCH IRQ flags on BXT
- check HAS_PCH_SPLIT instead of IS_BROXTON when handling PCH specific
  IRQ events in gen8_irq_handler()
- check HAS_PCH_SPLIT before calling the function instead of a
  corresponding early return within the called function for
  ibx_irq_reset(), ibx_irq_pre_postinstall(), ibx_irq_postinstall()
v3: (jani)
- in ironlake_irq_postinstall() and ironlake_irq_reset() HAS_PCH_SPLIT
  is always true, so drop the check for it

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <ppashank.sharma@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:53:03 +02:00
Shashank Sharma
d04a492dd5 drm/i915/bxt: Add DDI hpd handler
This patch adds a hot plug interrupt handler function for BXT.
What this function typically does is:
1. Check if hot plug is enabled from hot plug control register.
2. Call hpd_irq_handler with appropriate trigger to detect a
   plug storm and schedule a bottom half.
3. Clear sticky status bits in hot plug control register..

v2: (jani)
- drop redundant unlikely()
- s/Todo/FIXME:/ in code comment
- declare 'found' var in the scope where it's used
- check for IS_BROXTON before handling BXT_DE_PORT_HOTPLUG_MASK

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:53:03 +02:00
Imre Deak
6b5ad42f0a drm/i915/bxt: support for HPD long/short status decoding
All non-GMCH platforms have the same register layout for HPD long/short
status, so let's use this condition instead of HAS_PCH_SPLIT, as the
latter doesn't apply for BXT.

Noticed by Daniel.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:53:02 +02:00
Shashank Sharma
e0a20ad78c drm/i915/bxt: DDI Hotplug interrupt setup
In BXT, DDI hotplug control has been moved to CPU from PCH.
This patch adds a new IRQ setup function for BXT which:
1. Checks which HPD ports are requested to be enabled by encoders.
2. Enables those ports in the hot plug control register.
3. Un-masks these port interrupts in the IMR register.
4. Enables these port interrupts in the IER register.

V3: Kept the default HPD filter count to default (500 us) as per
    satheesh's comment
v4: Remove unused HPD filter defines (Damien)
v5: warn if trying to setup HPD on port A (imre)
v6: fix order of definitions for register bitfields (Daniel)
v7: (jani)
- define the size of the hpd_bxt array explicitly for bound checking
- use for_each_intel_encoder instead of open coding it
- fix format/order of definitions for BXT_HOTPLUG_CTL reg bitfields

Reviewed-by: Satheeshakrishna M <satheeshakrishna.m@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Shashank Sharma <shashank.sharma@intel.com> (v4)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:53:02 +02:00
Jani Nikula
4c27283415 drm/i915: add bxt gmbus support
For BXT gmbus is pulled from PCH to CPU. From implementation point of
view only pin pair configuration will change. The existing
implementation supports all platforms previous to GEN8 and also SKL. But
for BXT pin pair configuration is completely different than SKL or other
previous GEN's. This patch introduces the new pin pair configuration
structure specific to BXT and also ensures every real gmbus port has a
gpio pin.

v3 by Jani: with the platform independent prep work in place, the bxt
enabling reduces to a fairly trivial patch. Credits are due Sunil for
giving me the ideas (with his patches) what the platform independent
parts should look like.

v4: Fix intel_hdmi_init_connector() for bxt. Abstract gmbus_pin access
more. s/GPU/PCH/ in commit message.

v5: Rebase.

Issue: VIZ-3574
Signed-off-by: A.Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 14:01:55 +02:00
Daniel Vetter
c5fe557dde Merge branch 'topic/bxt-stage1' into drm-intel-next-queued
Separate topic branch for bxt didn't work out since we needed to
refactor the gmbus code a bit to make it look decent. So backmerge.

Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
2015-04-14 14:00:56 +02:00
Vandana Kannan
c776eb2edf drm/i915/bxt: don't use unsupported port detection
The port detection register flags in SFUSE_STRAP and DDI_BUF_CTL_A are
not defined for BXT, so don't use them.

Suggested by Satheesh.

v2:
- DDI_BUF_CTL_A bit 0 is not useful on BXT. Making changes to use this
  bit when simulator or BXT is not applicable. Code re-arranged as per
  Damien's suggestion.

v3:
- clarify commit message, add code comment (imre)

Signed-off-by: Vandana Kannan <vandana.kannan@intel.com> (v2)
Cc: M, Satheeshakrishna <satheeshakrishna.m@intel.com>
Cc: Lespiau, Damien <damien.lespiau@intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:24 +02:00
Robert Beckett
e3a290553f drm/i915/bxt: add workaround to avoid PTE corruption
Set TLBPF in TILECTL. This fixes an issue with BXT HW seeing
corrupted pte entries.

v2:
- move the workaround to bxt_init_clock_gating (imre)

Signed-off-by: Robert Beckett <robert.beckett@intel.com> (v1)
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:23 +02:00
Ben Widawsky
8d09c8123d drm/i915/skl: add WaDisableMaskBasedCammingInRCC workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:23 +02:00
Ben Widawsky
38a39a7be7 drm/i915/bxt: add WaDisableMaskBasedCammingInRCC workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:22 +02:00
Ben Widawsky
868434c51e drm/i915/bxt: add GEN8_HDCUNIT_CLOCK_GATE_DISABLE_HDCREQ workaround
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:22 +02:00
Imre Deak
32608ca255 drm/i915/bxt: add GEN8_SDEUNIT_CLOCK_GATE_DISABLE workaround
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:21 +02:00
Imre Deak
a82abe43ce drm/i915/bxt: add bxt_init_clock_gating
v2:
- Make the condition to select between SKL and BXT consistent with the
  corresponding condition in init_workarounds_ring (Nick)

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:21 +02:00
Imre Deak
9647ff36ae drm/i915/gen9: fix PIPE_CONTROL flush for VS_INVALIDATE
On GEN9+ per specification a NULL PIPE_CONTROL needs to be emitted
before any PIPE_CONTROL command with the VS_INVALIDATE flag set.

Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Nick Hoath <nicholas.hoath@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
2015-04-14 13:55:20 +02:00