The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it possible to transfer i2c message buffers via DMA.
Start/Stop/Sending_Slave_Address and some data is still handled using
the old state machine, it is sending the bulk of the data that is done
via DMA.
The first byte of a transmission and the last two bytes of reception are
sent/received using PIO. This is needed for the HW to have access to the
first byte before DMA transmit and to be able to set the STOP condition
for DMA reception.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Rob Herring <robh@kernel.org>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
[wsa: fixed a checkpatch warning]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for watchdogs (RWDT and SWDT) found on RCar Gen3 based SoCs
from Renesas.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The IMX6 watchdog supports assertion of a signal (WDOG_B) which
can be pinmux'd to an external pin. This is typically used for boards that
have PMIC's in control of the IMX6 power rails. In fact, failure to use
such an external reset on boards with external PMIC's can result in various
hangs due to the IMX6 not being fully reset [1] as well as the board failing
to reset because its PMIC has not been reset to provide adequate voltage for
the CPU when coming out of reset at 800Mhz.
This uses a new device-tree property 'fsl,ext-reset-output' to indicate the
board has such a reset and to cause the watchdog to be configured to assert
WDOG_B instead of an internal reset both on a watchdog timeout and in
system_restart.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2015-March/333689.html
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Iain Paton <ipaton0@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add device tree binding for the BCM6345 interrupt controller.
This controller is similar to the SMP-capable BCM7038 and
the BCM3380 but with packed interrupt registers.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Jonas Gorski <jogo@openwrt.org>
Cc: Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Cc: devicetree@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11804/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Document the devicetree bindings for the UART peripheral found on
Microchip PIC32 class devices.
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12100/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add irq_chip support for both IPI and "normal" interrupts of the CIU3
controller. Document the device tree binding for the CIU3.
Some functions are non-static as they will be used by follow-on
support for MSI-X.
Signed-off-by: David Daney <david.daney@cavium.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/12500/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some definitions to support the PCM5102A codec
by Texas Instruments.
Signed-off-by: Florian Meier <florian.meier@koalo.de>
Changes to original patch by Florian Meier:
* rebased (Makefile and Kconfig
* fixed checkpath errors (spaces, newlines)
* added dt-binding documentation
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull some non-critical i.MX clk fixes from Shawn Guo:
* Fix the commit 3713e3f5e9 ("clk: imx35: define two clocks for rtc")
which messed up the clock enumeration when adding new clock.
* tag 'imx-clk-fixes-4.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx35: restore existing used clock enumeration
clk: imx6q: fix typo in CAN clock definition
The A10 SoCs and its relatives has a special clock controller to drive the
display engines (both frontend and backend), that have a lot in common with
the clock to drive the first TCON channel.
Add a driver to support both.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
[sboyd@codeaurora.org: Silence variable sized array warning]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add support for TPK U.S.A. LLC Fusion 7", 10.1" panels to the DRM simple
panel driver.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ANX7814 is an ultra-low power Full-HD (1080p60) SlimPort transmitter
designed for portable devices.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Analogix Semiconductor Inc. develops analog and mixed-signal devices for
digital media and communications interconnect applications.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Innolux AT070TN92 panel.
Signed-off-by: Riccardo Bortolato <bortolato@navaltechitalia.it>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add support for the Olimex LCD-OLinuXino-4.3TS panel to the DRM simple
panel driver.
It is a 480x272 panel connected through a 24-bits RGB interface.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a basic TFT panel with a 40-pin FPC connector on it. The
specification doesn't define timings, but the Adafruit instructions
were setting up 800x480 CVT.
v2: Add .bus_format and vsync/hsync flags.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
[treding@nvidia.com: keep entries properly sorted]
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is the vendor for a 7" DPI panel sold by Adafruit which I'd like
to describe in DT.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch updates the device-tree binding doc for
adding support for AXI CDMA.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This patch updates the device-tree binding doc for
adding support for AXI DMA.
Also this patch differentiates required properties b/w
DMA and VDMA.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zM22
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.7 pull request
This is the first NFC pull request for 4.7. With this one we
mainly have:
- Support for NXP's pn532 NFC chipset. The pn532 is based on the same
microcontroller as the pn533, but it talks to the host through i2c
instead of USB. By separating the pn533 driver into core and PHY
parts, we can not add the i2c layer and support the pn532 chipset.
- Support for NCI's loopback mode. This is a testing mode where each
packet received by the NFCC is sent back to the DH, allowing the
host to test that the controller can receive and send data.
- A few ACPI related fixes for the STMicro drivers, in order to match
the device tree naming scheme.
- A bunch of cleanups for the st-nci and the st21nfca STMicro drivers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Resetting the switch is something the driver does, not the framework.
So move the parsing of this property into the driver.
There are no in kernel users of this property, so moving it does not
break anything. There is however a board which will make use of this
property making its way into the kernel.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow Marvell switches to be mdio devices. Currently the driver just
allocate the private structure and detects what device is on the
bus. Later patches will make them register with the DSA framework.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- New board support of LS1043a-QDS from Freescale/NXP
- Add new compatible for LS1043A and LS2080A GPIO devices
- Update device tree bindings and sources for LS2080A fsl-mc device
- Update QSPI and DSPI support on LS1043A and LS2080A
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXKL1RAAoJEFBXWFqHsHzOdO8H/1HeVve6KqhjpgHEYI0vqCQN
F8dC3kA8S9UZcozl58VrKvH+ArR2dcumfdl6ov/WVdfuWDwcBN3SKYgCK4xV1aN9
QtxFkc7uiE4InyDl4w9Q3fGRZfCgzk3eYUWQmHw6D0oQc3UhoIZ3cK+aKMB2nlZ1
Q4e0pO3Ell96sKYIhaG6rltlLc9U6Ax4z1XDl1CZ/T2njARFqwBfgNkjSdguB0Ks
+GOCd/TyloncdWoC41MQnwaOWc+msa3rkXJG2Aj1PWyocZPIiY0K68RClv1g/yKk
XZJ3M574QK+n/+Em0t+QaxrggiqT6kzr00CfULyyXQ4xhZO1siByCuxdEFW/tAs=
=pZW5
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt64
Merge "The Freescale/NXP arm64 device tree updates for 4.7" from Shawn Guo:
- New board support of LS1043a-QDS from Freescale/NXP
- Add new compatible for LS1043A and LS2080A GPIO devices
- Update device tree bindings and sources for LS2080A fsl-mc device
- Update QSPI and DSPI support on LS1043A and LS2080A
* tag 'imx-dt64-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: ls2080a: fsl-mc dt node updates
Documentation: fsl-mc: binding updates for MSIs, ranges, PHYs
arm64: dts: ls1043a: add the DTS node for QSPI support
Documentation: fsl-quadspi: Add fsl,ls1043a-qspi compatible string
arm64: dts: ls2080a: Add compatible "fsl,ls2080a-gpio" for ls2080a gpio nodes
arm64: dts: ls1043a: Add compatible "fsl,qoriq-gpio" for ls1043a gpio nodes
arm64: dts: ls2080a: update the DTS for QSPI and DSPI support
Documentation: fsl: dspi: Add fsl,ls2080a-dspi compatible string
arm64: dts: ls1043a-rdb: add the DTS for DSPI support
arm64: dts: add LS1043a-QDS board support
Documentation: DT: Add entry for Freescale LS1043a-QDS board
Complement the GM20B GPU device tree node on Tegra210 with missing
properties to make it usable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=yX4c
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-gm20b' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
Merge "arm64: tegra: Enable GM20B GPU on Tegra210" from Thierry Reding:
Complement the GM20B GPU device tree node on Tegra210 with missing
properties to make it usable.
* tag 'tegra-for-4.7-gm20b' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Add IOMMU node to GM20B on Tegra210
arm64: tegra: Add reference clock to GM20B on Tegra210
dt-bindings: Add documentation for GM20B GPU
dt-bindings: gk20a: Document iommus property
dt-bindings: gk20a: Fix typo in compatible name
Adds device tree bindings for the GPIO and AON controllers found on the
Tegra186 SoC.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXI3wAAAoJEN0jrNd/PrOhV2gQAJBrcTZ762hsnxvsbprE9cfc
th8hq750wVhqT7rJLLHcPcUMNAnhZyg69DEEKmhZGMCUfkTfWOMBcP0Iga4uP84G
RilK4A7srs/knUklK07XLBS1vhlnaikyUhpsHv0XTstsAsbRoLX1sBdRjWxf9uOM
8G0rptLsI6+BfTVZISWiXgZ9uuEkavFaPb8xonjtG1KVSq8S8x8p509hUZ6m5QOC
lTj2+Pt6MYwtJ1BBcdOtYEJGClmdjYGWfo8spQDQZFTywDU20TCIkdEe8QZVeoP1
WA/7Rgpn3VJJiSyUzBVcjRzWqjwpUa44yeGOqFegvQrOt+fK0Bh9KYaE9RhbAhMI
la4T5n401dgRb2VWzLXDCGIyMYcu64XYG537IxqoSuG8hAqhQt+FrkTo2wMotpxh
ErHmIIFTcivJQ2kEBEMd/QY8V+ey+99rFmrqaExLrHV+vmP+TEuw58GyCuNDSQ1T
xEvUwBZYFDpfm33DPm3IHJkYapAJ/sW+VFKBNT+Leim3tm8HqKap0OoP7aarCRYI
IjfkFd0NSFQ/Sxa3sGzbK4zS2MlfPQ9svAoy+YNDYZWmB7mwPaG4+/pOEygQXNdg
CkJxopNpdTpdmdmJE+Q2iGQc7w1fiUnKMlsKl5KHIO6Q9lWWp3ZDEYWxYvbpRMBB
VwgHyRoet1oKU/yjkOLA
=6MhO
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt64
Merge "dt-bindings: gpio: tegra: Add Tegra186 support" from Thierry Reding:
Adds device tree bindings for the GPIO and AON controllers found on the
Tegra186 SoC.
* tag 'tegra-for-4.7-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Add DT binding for Tegra186 GPIO controllers
ARM: tegra: Fix naming in GPIO DT binding header
- switch to label in the mvebu arm64 device tree
- use new clock binding on Armada 7K/8K
- improve SPI and I2C description on Armada 7K/8k
- add CP110 block adding PCIe, SATA and USB3
- add XOR support on Armada 3700
- few more little fix
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlcjbaAACgkQCwYYjhRyO9VaVgCghxZq/0qnD5+k5ouUvSYwXiOo
EV8AoIL6w3bn64kY93M0o8RtrG4WLe+h
=Pilg
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.7-1' of git://git.infradead.org/linux-mvebu into next/dt64
Merge "mvebu dt64 for 4.7" from Gregory CLEMENT:
- switch to label in the mvebu arm64 device tree
- use new clock binding on Armada 7K/8K
- improve SPI and I2C description on Armada 7K/8k
- add CP110 block adding PCIe, SATA and USB3
- add XOR support on Armada 3700
- few more little fix
* tag 'mvebu-dt64-4.7-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: add XOR node for Armada 3700 SoC
arm64: dts: marvell: Use a SoC-specific compatible for xHCI on Armada37xx
arm64: dts: marvell: Rename armada-37xx USB node
arm64: dts: marvell: Clean up armada-3720-db
arm64: dts: marvell: enable several CP interfaces on Armada 7040-DB
arm64: dts: marvell: initial DT description of Armada 7K/8K CP110 master
arm64: dts: marvell: use the proper I2C controller compatible string for 7K/8K
arm64: dts: marvell: improve SPI flash description on Armada 7040-DB
arm64: dts: marvell: use new clock binding on Armada AP806
arm64: dts: marvell: add UART aliases and define stdout-path
arm64: dts: marvell: rename armada-ap806 XOR nodes
arm64: dts: marvell: clean up armada-7040-db
dts for the evaluation board of this chip and similar to the arm32
side also move the rk3368 thermal data into the core soc dtsi, as
there really is no need to keep it separate.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIoubAAoJEPOmecmc0R2B/kQH/1gcN5C5JM4kkohUyEJ2uBju
zIwbfw4TyV/ndMUb1rCj8XUTBvbz80PvNKmsYJXERr8fUtjRaA71Wf8iJsqyaqDz
NQ3ygC30ZtmG2Z39ekn4cZ7zqjxwrEmY53vFfR4oDd1ENNVh14g26qxLfYDG7SXD
RGB729icDa2wr9W0doNc9khcQDFY3j4pbz+v8tfDoVcbFZWeq5K4SnbvB0VVQBCA
sS0EJV0KUUSlZ5okJuoZUx5UeeodJaV8uvygOboL644kI8hNnnp4rCP23paZ/d0H
ot5IcrXDjpCHCEQdQpr3OsCnCgzeK0NL5F1ppJr2MYfjQJSWEaGFQatV2Ipquss=
=25Hx
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt64
Merge "Rockchip dts64 updates for v4.7 - part2" from Heiko Stübner:
Adding the new rk3399 core devicetree support as well as a board
dts for the evaluation board of this chip and similar to the arm32
side also move the rk3368 thermal data into the core soc dtsi, as
there really is no need to keep it separate.
* tag 'v4.7-rockchip-dts64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
dt-bindings: document rockchip rk3399-evb board
arm64: dts: rockchip: add dts file for RK3399 evaluation board
arm64: dts: rockchip: add core dtsi file for RK3399 SoCs
dt-bindings: rockchip-dw-mshc: add description for rk3399
clk: rockchip: export some necessary rk3399 clock ids
clk: rockchip: rename rga clock-id on rk3399
clk: rockchip: add general gpu soft-reset on rk3399
arm64: dts: rockchip: move the rk3368 thermal data into rk3368.dtsi
clk: rockchip: fix checkpatch errors in rk3399 dt-binding header
clk: rockchip: add dt-binding header for rk3399
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ED1J
-----END PGP SIGNATURE-----
Merge tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux into next/dt
Merge "aspeed devicetree for 4.7" from Joel Stanley:
This device trees for a pair of Aspeed BMC SoCs and the boards that
they sit in.
* tag 'aspeed-for-4.7-dts' of https://github.com/shenki/linux:
arm/dst: Add Aspeed ast2500 device tree
arm/dts: Add Aspeed ast2400 device tree
doc/devicetree: Add Aspeed and Tyan to vendor-prefixes
to the binding-change that made it into 4.6, adds rk3288 i2c controller
nodes and moves the rk3288 thermal data into the soc dtsi, as there
really is no need to have that separate file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIoqfAAoJEPOmecmc0R2BBX0H/iBNCd50u66X9sAgpoi9HgPs
QghFjG9wxXUAtSGfMWirgmjMVNwCfNBTPUMHgZpIn61Yxgm5vh1dNTiBIGYoNVwv
XLLgSRmc4tHKdRQmdw2bik9Do4AKR0NfWN4UG1YtaJnPWVGiBPnlvGqr8sdJHZkS
VEPeh5sUgLi8nI5fR2UQxTlv5Epptal72k5kWrPWtLuFN3diPOPZ5tblSESt5OIE
EfNARkNVLMRtt+nEZyWF8hFtdIF+gJ+9CKwIt83w9c2Mudbrcpha+HYzOWVMUIY/
g0itfsoW48PyI81UpoBaNmKQXj5S0k8HuDrZ65HMgYWm9pJ5dNsJdlcyQolRmKM=
=rD4T
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 updates for v4.7 - part2" from Heiko Stübner:
This adds the rk3288-miqi as new board, adapts the edp-phy settings
to the binding-change that made it into 4.6, adds rk3288 i2c controller
nodes and moves the rk3288 thermal data into the soc dtsi, as there
really is no need to have that separate file.
* tag 'v4.7-rockchip-dts32-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the rk3288 thermal data into rk3288.dtsi
ARM: dts: rockchip: add MiQi board from mqmaker
dt-bindings: add vendor-prefix for mqmaker
ARM: dts: rockchip: move rk3288 edp phy under the GRF
ARM: dts: rockchip: make rk3288-grf a simple-mfd
ARM: dts: rockchip: add i2c nodes for RK3228 SoCs
This patch adds the device tree bindings for the Western Digital's
MyBook Live memory-mapped GPIO controllers.
The gpios will be supported by gpio-mmio code of the
GPIO generic library.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Make it possible to name the producer side of a GPIO line using
a "gpio-line-names" property array, modeled on the
"clock-output-names" property from the clock bindings.
This naming is especially useful for:
- Debugging: lines are named after function, not just opaque
offset numbers.
- Exploration: systems where some or all GPIO lines are available
to end users, such as prototyping, one-off's "makerspace usecases"
users are helped by the names of the GPIO lines when tinkering.
This usecase has been surfacing recently.
The gpio-line-names attribute is completely optional.
Example output from lsgpio on a patched Snowball tree:
GPIO chip: gpiochip6, "8000e180.gpio", 32 GPIO lines
line 0: unnamed unused
line 1: "AP_GPIO161" "extkb3" [kernel]
line 2: "AP_GPIO162" "extkb4" [kernel]
line 3: "ACCELEROMETER_INT1_RDY" unused [kernel]
line 4: "ACCELEROMETER_INT2" unused
line 5: "MAG_DRDY" unused [kernel]
line 6: "GYRO_DRDY" unused [kernel]
line 7: "RSTn_MLC" unused
line 8: "RSTn_SLC" unused
line 9: "GYRO_INT" unused
line 10: "UART_WAKE" unused
line 11: "GBF_RESET" unused
line 12: unnamed unused
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Amit Kucheria <amit.kucheria@linaro.org>
Cc: David Mandala <david.mandala@linaro.org>
Cc: Lee Campbell <leecam@google.com>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Michael Welling <mwelling@ieee.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- device tree binding documentation for all MT8173 display
subsystem components
- basic mediatek-drm driver for MT8173 with two optional,
currently fixed output paths:
- DSI encoder support for DSI and (via bridge) eDP panels
- DPI encoder support for output to HDMI bridge
- necessary clock tree changes for the DPI->HDMI path
- export mtk-smi functions used by mediatek-drm
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=vcoi
-----END PGP SIGNATURE-----
Merge tag 'mediatek-drm-2016-05-09' of git://git.pengutronix.de/git/pza/linux into drm-next
MT8173 DRM support
- device tree binding documentation for all MT8173 display
subsystem components
- basic mediatek-drm driver for MT8173 with two optional,
currently fixed output paths:
- DSI encoder support for DSI and (via bridge) eDP panels
- DPI encoder support for output to HDMI bridge
- necessary clock tree changes for the DPI->HDMI path
- export mtk-smi functions used by mediatek-drm
* tag 'mediatek-drm-2016-05-09' of git://git.pengutronix.de/git/pza/linux:
clk: mediatek: remove hdmitx_dig_cts from TOP clocks
clk: mediatek: Add hdmi_ref HDMI PHY PLL reference clock output
clk: mediatek: make dpi0_sel propagate rate changes
drm/mediatek: Add DPI sub driver
drm/mediatek: Add DSI sub driver
drm/mediatek: Add DRM Driver for Mediatek SoC MT8173.
dt-bindings: drm/mediatek: Add Mediatek display subsystem dts binding
memory: mtk-smi: export mtk_smi_larb_get/put
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into patchwork
Linux 4.6-rc7
* tag 'v4.6-rc7': (185 commits)
Linux 4.6-rc7
parisc: fix a bug when syscall number of tracee is __NR_Linux_syscalls
x86/tsc: Read all ratio bits from MSR_PLATFORM_INFO
mailmap: add John Paul Adrian Glaubitz
byteswap: try to avoid __builtin_constant_p gcc bug
lib/stackdepot: avoid to return 0 handle
mm: fix kcompactd hang during memory offlining
modpost: fix module autoloading for OF devices with generic compatible property
proc: prevent accessing /proc/<PID>/environ until it's ready
mm/zswap: provide unique zpool name
mm: thp: kvm: fix memory corruption in KVM with THP enabled
MAINTAINERS: fix Rajendra Nayak's address
mm, cma: prevent nr_isolated_* counters from going negative
mm: update min_free_kbytes from khugepaged after core initialization
huge pagecache: mmap_sem is unlocked when truncation splits pmd
rapidio/mport_cdev: fix uapi type definitions
mm: memcontrol: let v2 cgroups follow changes in system swappiness
mm: thp: correct split_huge_pages file permission
maintainers: update rmk's email address(es)
writeback: Fix performance regression in wb_over_bg_thresh()
...
The MAXIM PMIC MAX77620 and MAX20024 are power management IC
which supports RTC, GPIO, DCDC/LDO regulators, interrupt,
watchdog etc.
Add DT binding document for the different functionality of
this device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Implements generic PM domain support on top of the existing Tegra power-
gate API. Drivers are thus allowed to move away from the Tegra-specific
API and towards using generic power domains directly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=oeBF
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-genpd' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "soc/tegra: Add generic PM domain support" from Thierry Reding:
Implements generic PM domain support on top of the existing Tegra power-
gate API. Drivers are thus allowed to move away from the Tegra-specific
API and towards using generic power domains directly.
* tag 'tegra-for-4.7-genpd' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc/tegra: pmc: Add generic PM domain support
dt-bindings: Add power domain info for NVIDIA PMC
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=BcOx
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "usb: host: xhci-tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches introduces a driver for the XUSB controller found on
NVIDIA Tegra SoCs. When loaded with a firmware (available via the linux-
firmware repository), it provides an XHCI-compatible interface.
* tag 'tegra-for-4.7-xhci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
usb: xhci: tegra: Add Tegra210 support
usb: xhci: Add NVIDIA Tegra XUSB controller driver
dt-bindings: usb: xhci-tegra: Add Tegra210 XUSB controller support
dt-bindings: usb: Add NVIDIA Tegra XUSB controller binding
These patches update the Tegra PCIe host bridge controller device tree
bindings and driver to cope with per-lane PHYs on Tegra124 and later.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=38Xd
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "PCI: tegra: Changes for v4.7-rc1" from Thierry Reding:
These patches update the Tegra PCIe host bridge controller device tree
bindings and driver to cope with per-lane PHYs on Tegra124 and later.
* tag 'tegra-for-4.7-pci' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
PCI: tegra: Support per-lane PHYs
dt-bindings: pci: tegra: Update for per-lane PHYs
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JRT5
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Merge "phy: tegra: Changes for v4.7-rc1" from Thierry Reding:
This set of patches adds support for the Tegra XUSB pad controller. The
controller provides a set of pads (lanes) that are used for I/O by other
IP blocks within Tegra SoCs (PCIe, SATA and XUSB).
* tag 'tegra-for-4.7-phy' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
phy: tegra: Add Tegra210 support
phy: Add Tegra XUSB pad controller support
dt-bindings: phy: tegra-xusb-padctl: Add Tegra210 support
dt-bindings: phy: Add NVIDIA Tegra XUSB pad controller binding
phy: core: Allow children node to be overridden
clk: tegra: Add interface to enable hardware control of SATA/XUSB PLLs
settings that get lost and reset on power-domain power cycles.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXIom/AAoJEPOmecmc0R2BB7cH/RYBFTgvgI5PKJ+JuRyJrDh6
KDVTznZ5g+F99v+0PKtkA9qpToct+4Fo08CeLZPrtLR5vp2icQtbnNgHfV6K+JZu
T1NcNHPhI7yufHIBdlvLQlH/o4uLvSYeYuoJA3LwrkI1OYrxElD46PNZEwbGkLiE
oggmef8WtsUnZIeDIM4YVzmJabw8EbSTX+L1TUxMwlOJpR/tcct0RwFDdrBf5uKn
ionob7GblnJaKg045KhjP9bSpoZrltxwjcPqAZSOF9f2waPBqBPZCiFCNUfMLru6
RzzkCm799/6eFFB7wS87S1/6vnal54BnvfZYXIgnq5yStSHYY2VZX0FDkJhEKro=
=hluQ
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rockchip-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Merge "Rockchip driver updates for v4.7 - part2" from Heiko Stübner:
Ability to save and restore the power-domain quality of service
settings that get lost and reset on power-domain power cycles.
* tag 'v4.7-rockchip-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: power-domain: support qos save and restore
dt-bindings: modify document of Rockchip power domains
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=S5N0
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.6-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial fixes for v4.6-rc7
Here are some more new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2016-05-07
Here are a few more Bluetooth patches for the 4.7 kernel:
- NULL pointer fix in hci_intel driver
- New Intel Bluetooth controller id in btusb driver
- Added device tree binding documentation for Marvel's bt-sd8xxx
- Platform specific wakeup interrupt support for btmrvl driver
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding EZchip NPS400 support.
Internal interrupts are handled by Multi Thread Manager (MTM)
Once interrupt is serviced MTM is acked for deactivating the interrupt.
External interrupts are handled by MTM as well as at Global Interrupt
Controller (GIC) e.g. serial and network devices.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Add internal tick generator which is shared by all cores.
Each cluster of cores view it through dedicated address.
This is used for SMP system where all CPUs synced by same
clock source.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: John Stultz <john.stultz@linaro.org>
Acked-by: Vineet Gupta <vgupta@synopsys.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
ARC Timers have historically been probed directly.
As precursor to start probing Timers thru DT introduce these bindings
Note that to keep series bisectable, these bindings are not yet used in
code.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXL7HfAAoJEHm+PkMAQRiGYe8IAJBGaPUq38EJh2YOV+AQf9v6
t/alhwB3DUE1E0zjLy7I7JJ+xDXtKjZh9fS6OFuIS8Q3RIrBteIJ/oH8TPpt7yZ/
SnP6rYPvYD6CImTyrh7+ORL/udEwJX8+YqFYAgUAq167gvpDjYj8r26VzdIaIN4/
oBbL8NrQNWfODieywYyhUoitVhwMz09zmBfLtGVks4vd2jUJk2Fdd9cOtGV5tRfk
DPndPgyQtbr8W0mKovV8sT9WkQeV5TsUr4MLgf7hjnAGYQ8+0KamkzzVVLBeBiiw
uazyrOCFkddZp+N7KbmbOmazV/yULRuLGgDjVKazoCsOaKOvoGCzrCk7daOPy6Q=
=CegX
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc7' into drm-next
Merge this back as we've built up a fair few conflicts, and I have
some newer trees to pull in.
Pull libata fixes from Tejun Heo:
"An ahci driver addition and updates to ahci port enable handling for
some platform devices"
* 'for-4.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: add AMD Seattle platform driver
ARM: dts: apq8064: add ahci ports-implemented mask
ata: ahci-platform: Add ports-implemented DT bindings.
libahci: save port map for forced port map
This commit adds the DT binding documentation for the Marvell CP110
system controller, which is part of the CP110 HW block, itself used in
the Marvell Armada 7K and 8K SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Rob Herring <rob@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The CRG(Clock and Reset Generator) block provides clock
and reset signals for other modules in hi3519 soc.
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The ARC SDP I2S clock can be programmed using a
specific PLL.
This patch has the goal of adding a clock driver
that programs this PLL.
At this moment the rate values are hardcoded in
a table but in the future it would be ideal to
use a function which determines the PLL values
given the desired rate.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add entries for all supported chip variants into the of_match list, so that
the matching driver_info can be selected when using dt.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree binding documentation for the adv7180 video decoder family.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add device tree binding documentation for the display subsystem in
Mediatek MT8173 SoCs.
Signed-off-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Calling a GPIO LEDs is quite likely to work even if the kernel
has paniced, so they are ideal to blink in this situation.
This commit adds support for the new "panic-indicator"
firmware property, allowing to mark a given LED to blink on
a kernel panic.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
It's desirable to specify which LEDs are to be blinked on a kernel
panic. Therefore, introduce a devicetree boolean property to mark
which LEDs should be treated this way, if possible.
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Rob Herring <rob@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Now that we support nand-ecc-algo property it should be used together
with "soft" to specify software BCH ECC.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
So far it was only possible to specify ECC algorithm using "soft" and
"soft_bch" values of nand-ecc-mode prop. There wasn't a way to specify
it for a hardware ECC mode.
Now that we have independent field in NAND subsystem for storing info
about ECC algorithm we may also add support for this new DT property.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Document the DT bindings for controlling ARM PL310 Power Control
settings.
Discussion on the binding wording:
http://archive.arm.linux.org.uk/lurker/message/20160427.143444.5141d302.en.html
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On mx6ul the General Purpose Register 1 (GPR1) contains the following
bits for configuring the direction of the SAI MCLKs:
SAI1_MCLK_DIR, SAI2_MCLK_DIR, SAI3_MCLK_DIR
Introduce the "fsl,sai-mclk-direction-output" optional property to allow
configuring the SAI_MCLK outputs.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
MX6UL may need to configure the General Purpose Register 1 (GPR1), so
it is better to add a new compatible string to differentiate.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some Layerscape SoCs use a simple MSI controller implementation.
It contains only two SCFG register to trigger and describe a
group 32 MSI interrupts. The patch adds bindings to describe
the controller.
Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Summary:
- Support for pipeline clock between KMS drivers.
. Exynos SoC is required to control clocks across KMS drivers
according to Exynos SoC version. So this patch refactos
some relevant codes and provides generic solution for it.
- Add Exynos5433 SoC support to HDMI parts - HDMI and DECON-TV.
- Add HW trigger mode support to CRTC drivers.
. In case of using i80 Panel, some Exynos SoC supports HW trigger
mode so this patch makes trigger mode - HW or SW trigger - to be
set according to SoC version properly.
- And some cleanups and regression fixups.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos: (39 commits)
drm/exynos: clean up register definions for fimd and decon
drm/exynos: decon: clean up interface type
drm/exynos: fimd: add HW trigger support
drm/exynos: clean up wait_for_vblank
drm/exynos: mixer: use generic of_device_get_match_data helper
drm/exynos: mixer: remove support for non-dt platforms
drm/exynos: hdmi: use generic of_device_get_match_data helper
drm/exynos: rotator: use generic of_device_get_match_data helper
drm/exynos: fimd: use generic of_device_get_match_data helper
drm/exynos: dsi: use generic of_device_get_match_data helper
drm/exynos: exynos5433_decon: use generic of_device_get_match_data helper
drm/exynos: convert clock_enable crtc callback to pipeline clock
drm/exynos/mixer: enable HDMI-PHY before configuring MIXER
drm/exynos/decon5433: enable HDMI-PHY before configuring DECON
drm/exynos: add support for pipeline clock to the framework
drm/exynos: add helper to get crtc from pipe
drm/exynos/decon5433: do not protect window in plane disable
drm/exynos/decon5433: reset decon on start
drm/exynos/decon5433: fix DECON standalone update
drm/exynos/hdmi: remove registry dump
...
render nodes for vc4.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3dIy
-----END PGP SIGNATURE-----
Merge tag 'drm-vc4-next-2016-05-02' of https://github.com/anholt/linux into drm-next
This pull request brings in DPI panel support, gamma ramp support, and
render nodes for vc4.
* tag 'drm-vc4-next-2016-05-02' of https://github.com/anholt/linux:
drm/vc4: Add missing render node support
drm/vc4: Add support for gamma ramps.
drm/vc4: Fix NULL deref in HDMI init error path
drm/vc4: Add DPI driver
drm: Add an encoder and connector type enum for DPI.
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The System Trace Macrocell (STM) is an IP block falling under the
CoreSight umbrella. It's main purpose it so expose stimulus channels
to any system component for the purpose of information logging.
Bindings for this IP block adds a couple of items to the current
mandatory definition for CoreSight components.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
*) Add a new PHY driver for USB2 PHY on Northstar SoC
*) Add support for Broadcom NS2 SATA3 PHY in existing
Broadcom SATA3 PHY driver
*) Add support for MIPI DPHYs in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs
*) Add support for USB3 PHY on mt2701
*) Add extcon support for Renesas R-car USB2 PHY driver
*) Misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uHWi
-----END PGP SIGNATURE-----
Merge tag 'phy-for-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-testing
Kishon writes:
phy: for 4.7
*) Add a new PHY driver for USB2 PHY on Northstar SoC
*) Add support for Broadcom NS2 SATA3 PHY in existing
Broadcom SATA3 PHY driver
*) Add support for MIPI DPHYs in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs
*) Add support for USB3 PHY on mt2701
*) Add extcon support for Renesas R-car USB2 PHY driver
*) Misc cleanups
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Due to erratum #27704, the CN88xx SMMUv2 implementation supports only
shared ASID and VMID numberspaces.
This patch ensures that ASID and VMIDs are unique across all SMMU
instances on affected Cavium systems.
Signed-off-by: Tirumalesh Chalamarla <tchalamarla@caviumnetworks.com>
Signed-off-by: Akula Geethasowjanya <Geethasowjanya.Akula@caviumnetworks.com>
[will: commit message, comments and formatting]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Armada 3700 SoC comprise a single XOR engine compliant with the ones used
in older Marvell SoC's like Armada XP or 38x. The only thing that needs
modification is the Mbus configuration, which has to be done on two
levels: global and in device. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed.
Patch "dmaengine: mv_xor: optimize performance by using a subset
of the XOR channels" introduced limitation for using XOR engines and
channels vs number of available CPU's. Those constraints do not however
fit Armada 3700 architecture with two possible CPU's and single,
dual-channel engine. Hence in this commit an adjustment for setting
maximum available channels is added.
This patch enables XOR access to DRAM by opening default window to 4GB
space with specific attribute.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Major changes:
brcmfmac
* add support for nl80211 BSS_SELECT feature
mwifiex
* add platform specific wakeup interrupt support
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXJztPAAoJEG4XJFUm622beSAIAKIw8zGcs7DWd/AGd9z8D7L5
DeO6fxhiu/05AU3d1jM7Rp/Z5hZ42s41PDjRN1lkZJaF4Squa7XOxuB35JlPd+o8
2S21lvaM6ABraSEcDdYL++rglXFL65gIesv/W4TuxqdJCmi9fL7ie7ccplQH17bi
KyY3ePihHZPOR8aXMRbdEzTEjjPFaO/LlAghHPw5WKmVy7FkFKSyFR8muFEPnKEl
DSBWmG6GqRQaHUuVl1QOmoEEqiv7h85D+YqwKiy/xEM4Yw5Rmt5n5pj02KA0i4y5
IRZs59I/8zdAgDgBd+liVeBw9Gp2xAV5R8afOTdzViBDrqCbDCwNq6OPG1GmkLw=
=lyGT
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-05-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.7
Major changes:
brcmfmac
* add support for nl80211 BSS_SELECT feature
mwifiex
* add platform specific wakeup interrupt support
ath10k
* implement set_tsf() for 10.2.4 branch
* remove rare MSI range support
* remove deprecated firmware API 1 support
ath9k
* add module parameter to invert LED polarity
wcn36xx
* fixes to get the driver properly working on Dragonboard 410c
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the detailed corrleation between sub-blocks and power line
for Exynos5422.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds NoC (Network on Chip) Probe driver which provides
the primitive values to get the performance data. The packets that the Network
on Chip (NoC) probes detects are transported over the network infrastructure.
Exynos542x bus has multiple NoC probes to provide bandwidth information about
behavior of the SoC that you can use while analyzing system performance.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Markus Reichl <m.reichl@fivetechno.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the detailed correlation between sub-blocks and power line
for Exynos3250, Exynos4210 and Exynos4x12.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch updates the documentation for passive bus devices and adds the
detailed example of Exynos3250.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
This patch adds the documentation for generic exynos bus frequency
driver.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
As usual, a bunch of clocks patches for 4.7, mostly fixes and cleanups, and
display-related clocks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ttF/
-----END PGP SIGNATURE-----
Merge tag 'sunxi-clocks-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into clk-next
Pull Allwinner clock driver updates from Maxime Ripard:
As usual, a bunch of clocks patches for 4.7, mostly fixes and cleanups, and
display-related clocks.
* tag 'sunxi-clocks-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
clk: sunxi: Let divs clocks read the base factor clock name from devicetree
clk: sunxi: Add TCON channel1 clock
clk: sunxi: Add PLL3 clock
dt-bindings: clk: sun5i: add DRAM gates compatible
clk: sunxi: Use resource_size
clk: sunxi: Add sun6i/8i display support
clk: sunxi: mod1 clock should modify it's parent
I.MX6+ has a dedicated bit for resetting PCIe core, which should be used
instead of a regular reset sequence since using the latter will hang the
SoC.
This commit is based on c34068d48273e24d392d9a49a38be807954420ed from
http://git.freescale.com/git/cgit.cgi/imx/linux-2.6-imx.git
Tested-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add device tree binding documentation for MARVELL's bluetooth sdio
(sd8897 and sd8997) chip.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking fixes from David Miller:
1) MODULE_FIRMWARE firmware string not correct for iwlwifi 8000 chips,
from Sara Sharon.
2) Fix SKB size checks in batman-adv stack on receive, from Sven
Eckelmann.
3) Leak fix on mac80211 interface add error paths, from Johannes Berg.
4) Cannot invoke napi_disable() with BH disabled in myri10ge driver,
fix from Stanislaw Gruszka.
5) Fix sign extension problem when computing feature masks in
net_gso_ok(), from Marcelo Ricardo Leitner.
6) lan78xx driver doesn't count packets and packet lengths in its
statistics properly, fix from Woojung Huh.
7) Fix the buffer allocation sizes in pegasus USB driver, from Petko
Manolov.
8) Fix refcount overflows in bpf, from Alexei Starovoitov.
9) Unified dst cache handling introduced a preempt warning in
ip_tunnel, fix by resetting rather then setting the cached route.
From Paolo Abeni.
10) Listener hash collision test fix in soreuseport, from Craig Gallak
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (47 commits)
gre: do not pull header in ICMP error processing
net: Implement net_dbg_ratelimited() for CONFIG_DYNAMIC_DEBUG case
tipc: only process unicast on intended node
cxgb3: fix out of bounds read
net/smscx5xx: use the device tree for mac address
soreuseport: Fix TCP listener hash collision
net: l2tp: fix reversed udp6 checksum flags
ip_tunnel: fix preempt warning in ip tunnel creation/updating
samples/bpf: fix trace_output example
bpf: fix check_map_func_compatibility logic
bpf: fix refcnt overflow
drivers: net: cpsw: use of_phy_connect() in fixed-link case
dt: cpsw: phy-handle, phy_id, and fixed-link are mutually exclusive
drivers: net: cpsw: don't ignore phy-mode if phy-handle is used
drivers: net: cpsw: fix segfault in case of bad phy-handle
drivers: net: cpsw: fix parsing of phy-handle DT property in dual_emac config
MAINTAINERS: net: Change maintainer for GRETH 10/100/1G Ethernet MAC device driver
gre: reject GUE and FOU in collect metadata mode
pegasus: fixes reported packet length
pegasus: fixes URB buffer allocation size;
...
Add a decription of the PPI partitioning support.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/1460365075-7316-6-git-send-email-marc.zyngier@arm.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXJoi6AAoJEHm+PkMAQRiGYKIIAIcocIV48DpGAHXFuSZbzw5D
rp9EbE5TormtddPz1J1zcqu9tl5H8tfxS+LvHqRaDXqQkbb0BWKttmEpKTm9mrH8
kfGNW8uwrEgTMMsar54BypAMMhHz4ITsj3VQX5QLSC5j6wixMcOmQ+IqH0Bwt3wr
Y5JXDtZRysI1GoMkSU7/qsQBjC7aaBa5VzVUiGvhV8DdvPVFQf73P89G1vzMKqb5
HRWbH4ieu6/mclLvW9N2QKGMHQntlB+9m2kG9nVWWbBSDxpAotwqQZFh3D52MBUy
6DH/PNgkVyDhX4vfjua0NrmXdwTfKxLWGxe4dZ8Z+JZP5c6pqWlClIPBCkjHj50=
=KLSM
-----END PGP SIGNATURE-----
Merge tag 'v4.6-rc6' into patchwork
Linux 4.6-rc6
* tag 'v4.6-rc6': (762 commits)
Linux 4.6-rc6
EDAC: i7core, sb_edac: Don't return NOTIFY_BAD from mce_decoder callback
Documentation/sysctl/vm.txt: update numa_zonelist_order description
lib/stackdepot.c: allow the stack trace hash to be zero
rapidio: fix potential NULL pointer dereference
mm/memory-failure: fix race with compound page split/merge
ocfs2/dlm: return zero if deref_done message is successfully handled
Ananth has moved
kcov: don't profile branches in kcov
kcov: don't trace the code coverage code
mm: wake kcompactd before kswapd's short sleep
.mailmap: add Frank Rowand
mm/hwpoison: fix wrong num_poisoned_pages accounting
mm: call swap_slot_free_notify() with page lock held
mm: vmscan: reclaim highmem zone if buffer_heads is over limit
numa: fix /proc/<pid>/numa_maps for THP
mm/huge_memory: replace VM_NO_THP VM_BUG_ON with actual VMA check
mailmap: fix Krzysztof Kozlowski's misspelled name
thp: keep huge zero page pinned until tlb flush
mm: exclude HugeTLB pages from THP page_mapped() logic
...
There several changes are done here:
- Convert the property to be in bytes
Besides that this is a common practice for such property, the use of a value
in bytes much more convenient than handling the encoded one.
- Rename data_width to data-width in the device tree bindings
The change leaves the support for the old format as well just in case someone
will use a newer kernel with an old device tree blob.
- While here, replace dwc_fast_ffs() by __ffs()
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add a pinctrl binding to specify different pin settings for high speed
modes and UHS modes.
Signed-off-by: Lars Persson <larper@axis.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Implement voltage switch, supporting modes up to SDR-50.
Based on work by Shinobu Uehara, Rob Taylor, William Towle and Ian Molton.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds documentation of device tree bindings for the
UART found on ARM MPS2 platform
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vladimir Murzin <vladimir.murzin@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the SiRF UART driver from using the vendor-specific
"sirf,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale MXS AUART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but it is deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Convert the Freescale IMX UART driver from using the vendor-specific
"fsl,uart-has-rtscts" to the generic "uart-has-rtscts" DT property, as
documented by the Generic Serial DT Bindings.
The old vendor-specific property is still recognized by the driver for
backwards compatibility, but deprecated.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document a set of generic properties for describing UARTs in a
device tree:
1. The GPIO modem control properties are currently duplicated across
hardware-specific binding documentation,
2. The property for dedicated RTS/CTS hardware flow control lines is
already supported by several drivers, albeit with a vendor-specific
prefix, hence make it generic.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <rob@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All other UART DT binding documentation is under
Documentation/devicetree/bindings/serial/.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Alphascale ASM9260 uart IP has some common registers with
Freescale STMP37XX. This patch provide changes which
allow to reuse mxs-auart.c code for ASM9260.
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds support for MIPI DPHYs found in Exynos5420-compatible
(5420, 5422 and 5800) and Exynos5433 SoCs. Those SoCs differs from
earlier by different offset of MIPI DPHY registers in PMU controllers
(Exynos 5420-compatible case) or by moving MIPI DPHY reset registers to
separate system register controllers (Exynos 5433 case). In both case
also additional 5th PHY (MIPI CSIS 2) has been added.
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Northstar is a family of SoCs used in home routers. They have USB 2.0
and 3.0 controllers with PHYs that need to be properly initialized.
This driver provides PHY init support in a generic way and can be bound
with an EHCI controller driver.
There are (just a few) registers being defined in bcma header. It's
because DMU/CRU registers will be also needed in other drivers. We will
need them e.g. in PCIe controller/PHY driver and at some point probably
in clock driver for BCM53573 chipset. By using include/linux/bcma/ we
avoid code duplication.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new compatible string for "mt2701"
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
To handle the VBUS on/off by a regulator driver, this patch adds
regulator APIs calling in the driver and description about vbus-supply
in the rcar-gen3-phy-usb2.txt.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
The following patch adds the required match table for device tree support
(and while at, fix the indent). It's also possible to specify the
MAC address in the DT blob.
Also add the corresponding binding documentation file.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes property port-id to reg in dsaf port node,
removes property cpld-ctrl-reg, and fixes some typos.
Signed-off-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DECON-TV(Display and Enhancement Controller for TV) is a variation
of DECON IP. Its main purpose is to produce video stream for HDMI IP.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON IP requires this clock to access configuration registers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos5433 variant of HDMI requires different set of clocks and sysreg
phandle to system registers.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Extend the Tegra XUSB controller device tree binding with Tegra210
support.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add device-tree binding documentation for the XUSB controller present
on Tegra124 and later SoCs. This controller supports USB 3.0 via an xHCI
compliant interface.
Based on work by Andrew Bresticker <abrestic@chromium.org>.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The XUSB pad controller allows PCIe lanes to be controlled individually,
providing fine-grained control over their power state. Previous attempts
at describing the XUSB pad controller in DT had erroneously assumed that
all PCIe lanes were driven by the same PHY, and hence the PCI host
controller would reference only a single PHY.
Moving to a representation of per-lane PHYs requires that the operating
system driver for the PCI host controller have access to the set of PHY
devices that make up the connection of each root port in order to power
up and down all of the lanes as necessary.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Extend the binding to cover the set of feature found in Tegra210.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The NVIDIA Tegra XUSB pad controller provides a set of pads, each with a
set of lanes that are used for PCIe, SATA and USB.
A binding exists for the XUSB pad controller already, but it turned out
not to be flexible enough to describe all aspects of the controller. In
particular, the addition of XUSB support (for SuperSpeed USB) has shown
that the existing binding is no longer suitable. Mark the old binding
as deprecated and link to the new binding.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
In the case of Renesas R-Car hardware we know that there are generations of
SoCs, e.g. Gen 2 and Gen 3. But beyond that its not clear what the
relationship between IP blocks might be. For example, I believe that
r8a7790 is older than r8a7791 but that doesn't imply that the latter is a
descendant of the former or vice versa.
We can, however, by examining the documentation and behaviour of the
hardware at run-time observe that the current driver implementation appears
to be compatible with the IP blocks on SoCs within a given generation.
For the above reasons and convenience when enabling new SoCs a
per-generation fallback compatibility string scheme being adopted for
drivers for Renesas SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add ADE display controller binding doc.
Add DesignWare DSI Host Controller v1.20a binding doc.
v8: None.
v7: Acked by Rob Herring.
v6:
- Cleanup values part of reg and clocks properties.
- Change "pclk_dsi" clock name to "pclk".
v5:
- Remove endpoint unit address of dsi output port.
- Add "hisilicon,noc-syscon" property for ADE NOC QoS syscon.
- Add "resets" property for ADE reset.
v4:
- Describe more specific of clocks and ports.
- Fix indentation.
v3:
- Make ade as the drm master node.
- Use assigned-clocks to set clock rate.
- Use ports to connect display relavant nodes.
v2:
- Move dt binding docs to bindings/display/hisilicon directory.
Signed-off-by: Xinliang Liu <xinliang.liu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Acked-by: Rob Herring <robh@kernel.org>
This adds very rudimentary TCON (timing controller for raw LCD displays)
support to enable the bypass mode in order to use the DCU controller on
Freescale/NXP Vybrid SoC's.
Additionally the register clock and pixel clock has been separated, but
are currently still enabled and disabled pairwise.
Other than that, fixes and cleanups accross the driver.
* 'for-next' of http://git.agner.ch/git/linux-drm-fsl-dcu:
drm/fsl-dcu: increment version and date
drm/fsl-dcu: implement lastclose callback
drm/fsl-dcu: disable output polling on driver unload
drm/fsl-dcu: deallocate fbdev CMA on unload
drm/fsl-dcu: use variable name dev for struct drm_device
drm/fsl-dcu: handle missing panel gracefully
drm/fsl-dcu: detach panel on destroy
drm/layerscape: reduce excessive stack usage
drm/fsl-dcu: add TCON driver
drm/fsl-dcu: use common clock framework for pixel clock divider
drm/fsl-dcu: add extra clock for pixel clock
drm/fsl-dcu: disable clock on initialization failure and remove
- Fix few typos for address-cells and interrupt-names
- Update dra7 voltage rail limits
- Update compatible string for pcf8575 for both nxp and ti prefix
- Add omap5 configuration for gpadc
- Update dra7 for qspi to remove pinmux as it needs to be done by
the bootloader in isolation. Also update the qspi for 64MHz
frequency.
- Add support for Baltos ir2110 and ir3220
- Add industrial and commercial grade thermal thresholds for am57xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LRKX
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "Part two of device tree changes for omaps for v4.7 merge window" from Tony Lindgren:
- Fix few typos for address-cells and interrupt-names
- Update dra7 voltage rail limits
- Update compatible string for pcf8575 for both nxp and ti prefix
- Add omap5 configuration for gpadc
- Update dra7 for qspi to remove pinmux as it needs to be done by
the bootloader in isolation. Also update the qspi for 64MHz
frequency.
- Add support for Baltos ir2110 and ir3220
- Add industrial and commercial grade thermal thresholds for am57xx
* tag 'omap-for-v4.7/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-idk: Include Industrial grade thermal thresholds
ARM: dts: am57xx-beagle-x15: Include the commercial grade thresholds
ARM: dts: am57xx: Introduce industrial grade thermal thresholds
ARM: dts: am57xx: Introduce commercial grade thermal thresholds
ARM: dts: add DTS for Baltos IR2110
ARM: dts: add DTS for Baltos IR3220
ARM: dts: split am335x-baltos-ir5221 into dts and dtsi files
ARM: dts: dra7x: Support QSPI MODE-0 operation at 64MHz
ARM: dts: dra7x: Remove QSPI pinmux
ARM: dts: omap5-board-common: describe gpadc for Palmas
ARM: dts: twl6030: describe gpadc
ARM: dts: dra7xx: Fix compatible string for PCF8575 chip
ARM: dts: AM57xx/DRA7: Update SoC voltage rail limits to match data sheet
ARM: dts: OMAP36xx: : DT spelling s/#address-cell/#address-cells/
ARM: dts: omap5-cm-t54: DT spelling s/interrupt-name/interrupt-names/
ARM: dts: omap5-board-common: DT spelling s/interrupt-name/interrupt-names/
The phy-handle, phy_id, and fixed-link properties are mutually exclusive,
and only one need be specified. Make this clear in the binding doc.
Also mark the phy_id property as deprecated, as phy-handle should be
used instead.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This moves Samsung SROM controller code from arm/mach-exynos into to
separate driver under drivers/memory/samsung. In the future this driver
will be re-used on ARM64 Exynos platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=6ukR
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-srom-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Merge "Samsung soc/drivers update for v4.7" from Krzysztof Kozłowski:
This moves Samsung SROM controller code from arm/mach-exynos into to
separate driver under drivers/memory/samsung. In the future this driver
will be re-used on ARM64 Exynos platform.
* tag 'samsung-drivers-exynos-srom-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
memory: samsung: exynos-srom: Add support for bank configuration
ARM: EXYNOS: Remove SROM related register settings from mach-exynos
MAINTAINERS: Add maintainers entry for drivers/memory/samsung
memory: Add support for Exynos SROM driver
dt-bindings: EXYNOS: Add exynos-srom device tree binding
ARM: dts: change SROM node compatible from generic to model specific
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7szP
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: changes for v4.7 merge window
Here's the big USB Gadget pull request. This time
not as large as usual with only 57 non-merge
commits.
The most important part here is, again, all the work
on dwc3. This time around we're treating all
endpoints (except for control endpoint) exactly the
same. They all have the same amount of TRBs on the
ring, they all treat the ring as an actual ring with
a link TRB pointing to the head, etc.
We're also helping the host side burst (on
SuperSpeed GEN1 or GEN2 at least) for as long as
possible until the endpoint returns NRDY.
Other than this big TRB ring rework on dwc3, we also
have a dwc3-omap DMA initialization fix, some extra
debugfs files to aid in some odd debug sessions and
a complete removal of our FIFO resizing logic.
We have a new quirk for some dwc3 P3 quirk in some
implementations.
The rest is basically non-critical fixes and the
usual cleanups.
- Fix its node without msi-cells for hip05
- Add nor flash node for hip05 D02 board
- Add initial dts for hip06 D03 board
- Reorder and add the hip06 D03 binding in the binding document
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=OZ3Q
-----END PGP SIGNATURE-----
Merge tag 'hip0x-dt-for-4.7' of git://github.com/hisilicon/linux-hisi into next/dt64
Merge "ARM64: DT: Hisilicon hip05 and hip06 updates for 4.7" Wei Xu:
- Fix its node without msi-cells for hip05
- Add nor flash node for hip05 D02 board
- Add initial dts for hip06 D03 board
- Reorder and add the hip06 D03 binding in the binding document
* tag 'hip0x-dt-for-4.7' of git://github.com/hisilicon/linux-hisi:
Documentation: arm64: Add Hisilicon Hip06 D03 dts binding
arm64: dts: Add initial dts for Hisilicon Hip06 D03 board
arm64: dts: hip05: Add nor flash support
arm64: dts: hip05: fix its node without msi-cells
This fixes several spelling mistakes in the Documentation/ tree, which
are caught by checkpatch.pl's spell checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This includes a few functional changes:
* new representation of MIC, SIC1 and SIC2 interrupt controllers,
* disabled by default SPI1, SPI2, SSP0 and SSP1 SPI controllers in
shared lpc32xx.dtsi file,
* added clock sources for SPI1 and SPI2,
* set default clock rate of HCLK PLL to main osc rate multiplied by 16.
Also there are some non-functional changes:
* flatten board DTS files by exploiting device node labels,
* add 'partitions' device node for NAND SLC / MTD OF,
* correct Atmel vendor prefix to describe on board AT24 EEPROMs,
* rename board DTS files by adding SoC name prefix.
Since now DTS files of LPC32xx boards match "^lpc32[2345]0-" pattern.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=wDt+
-----END PGP SIGNATURE-----
Merge tag 'lpc32xx-dt-4.7' of git://github.com/vzapolskiy/linux-lpc32xx into next/dt
Merge "NXP LPC32xx device tree updates for v4.7" from Vladimir Zapolskiy:
This includes a few functional changes:
* new representation of MIC, SIC1 and SIC2 interrupt controllers,
* disabled by default SPI1, SPI2, SSP0 and SSP1 SPI controllers in
shared lpc32xx.dtsi file,
* added clock sources for SPI1 and SPI2,
* set default clock rate of HCLK PLL to main osc rate multiplied by 16.
Also there are some non-functional changes:
* flatten board DTS files by exploiting device node labels,
* add 'partitions' device node for NAND SLC / MTD OF,
* correct Atmel vendor prefix to describe on board AT24 EEPROMs,
* rename board DTS files by adding SoC name prefix.
Since now DTS files of LPC32xx boards match "^lpc32[2345]0-" pattern.
* tag 'lpc32xx-dt-4.7' of git://github.com/vzapolskiy/linux-lpc32xx:
ARM: dts: lpc32xx: phy3250: add SoC name prefix to board dts file
ARM: dts: lpc32xx: phy3250: add NAND partitions device node
ARM: dts: lpc32xx: phy3250: avoid extension of device nodes by absolute path
ARM: dts: lpc32xx: ea3250: add SoC name prefix to board dts file
ARM: dts: lpc32xx: ea3250: fix Atmel at24 eeprom vendor
ARM: dts: lpc32xx: ea3250: add NAND partitions device node
ARM: dts: lpc32xx: ea3250: avoid extension of device nodes by absolute path
ARM: dts: lpc32xx: reparent SIC1 and SIC2 interrupts from MIC
dt-bindings: interrupt-controllers: add description of SIC1 and SIC2
ARM: dts: lpc32xx: disabled ssp0/spi1 & ssp1/spi2 by default
ARM: dts: phy3250: enable ssp0
ARM: dts: lpc32xx: add clock properties to spi nodes
ARM: dts: lpc32xx: set default clock rate of HCLK PLL
