The 98DX2530 SoC is the Control and Management CPU integrated into
the Marvell 98DX25xx and 98DX35xx series of switch chip (internally
referred to as AlleyCat5 and AlleyCat5X).
These files have been taken from the Marvell SDK and lightly cleaned
up with the License and copyright retained.
gregory.clement: use specific cpu type: cortex-a55 instead of armv8 in
cpu nodes, armv8 being reserved for the arm virtual models that are
not meant to implement a particular CPU type.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
mvebu dt for 5.20 (part 1)
Enable LED to link/activity on turris-omnia (Armada 385 based)
* tag 'mvebu-dt-5.20-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: turris-omnia: enable LED controller node
ARM: dts: turris-omnia: configure LED[0] pin function to link/activity
Link: https://lore.kernel.org/r/87lespqn28.fsf@BL-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The marvell PHY driver changes the LED[0] pin function to "On - 1000
Mbps Link, Off - Else".
Turris Omnia expects that the function is "On - Link, Blink - Activity,
Off - No link".
Use the `marvell,reg-init` DT property to change the function.
In the future, once netdev trigger will support HW offloading, we will
be able to have this configured via the combination of PHY driver and
leds-turris-omnia driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
This pull request contains Broadcom ARM64-based SoCs Device Tree changes
for 5.20, second part, please pull the following:
- Rafal adds basic support for the BCM4912-based router Asus GT-AX6000,
he also has ARCH_BCM4908 select ARCH_BCMBCA such that in the next cycle
we can remove ARCH_BCM4908 and continue to have make oldconfig work.
Finally he spells out what BCA means to make it clearer
* tag 'arm-soc/for-5.20/devicetree-arm64-part2' of https://github.com/Broadcom/stblinux:
arm64: bcmbca: Include full family name in Kconfig
arm64: make ARCH_BCM4908 select ARCH_BCMBCA
arm64: dts: Add base DTS file for bcmbca device Asus GT-AX6000
Link: https://lore.kernel.org/r/20220715221642.297536-3-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
BCA is a big set / family of devices sharing multiple hardware blocks.
It covers BCM4908, BCM63xx, BCM68xx devices and more.
Most of drivers that depend on ARCH_BCM4908 should actually depend on
ARCH_BCMBCA. To make such transition easier, cleaner and breakage-free
add a proper "select".
Later on - if we decide to keep ARCH_BCM4908 - it may be moved under
ARCH_BCMBCA menu. Keeping it may be helpful for limited compiling of DTS
files and "default" Kconfig entires. Or we may just decide to drop it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: William Zhang <william.zhang@broadcom.com>
Acked-by: Kursad Oney <kursad.oney@broadcom.com>
Link: https://lore.kernel.org/r/20220714045858.7786-1-zajec5@gmail.com
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This pull request contains Broadcom ARM64-based SocS Device Tree
updates for 5.20, please pull the following:
- William adds the ARCH_BCMBCA Kconfig entry to follow the ARM 32-bit
counter part and adds basic support for these DSL/PON SoCs: 63158,
4912, 63146, 6856, 6813
- Anand adds basic support for the 6858 SoC
- Krzysztof fixes a missing space between a property name and its value
in a number of DTS files
* tag 'arm-soc/for-5.20/devicetree-arm64' of https://github.com/Broadcom/stblinux:
arm64: dts: Add DTS files for bcmbca SoC BCM6813
arm64: dts: Add DTS files for bcmbca SoC BCM6856
arm64: dts: Add DTS files for bcmbca SoC BCM63146
arm64: dts: broadcom: adjust whitespace around '='
ARM64: dts: Add DTS files for bcmbca SoC BCM6858
arm64: dts: Add DTS files for bcmbca SoC BCM4912
arm64: dts: Add DTS files for bcmbca SoC BCM63158
arm64: bcmbca: add arch bcmbca machine entry
Link: https://lore.kernel.org/r/20220711164451.3542127-5-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This pull request contains Broadcom ARM-based SoCs Device Tree updates
for 5.20, please pull the following:
- Stefan drops the unnecessary "#address-cells" and "#size-cells"
properties from the DPI node of BCM283x
- Anand documents and adds support for the 63178 and 6858 SoCs
- William migrates the 63138 platform over to ARCH_BCMBCA and ensures
that it is documented within the BCMBCA Device Tree binding documents.
He updates the 47622 DTS to remove unnecessary PSCI properties, fix
the GIC nodes and some minor cosmetic changes. He finally adds support
for the 63158, 4912, 6846, 6855, 6756, 63146, 6856, 63148, 6813, 6318
SoCs.
- Peter, Nicolas and Stefan adds the necessary Device Tree nodes to the
BCM2711 (Raspberry Pi 4) DTS to enable the use of the V3D GPU on these
platforms.
- Christian adds support for the BCM53015 based Cisco Meraki MR26
Wi-Fi access point.
- Krzysztof updates the Broadcom platforms DTS to add a missing
whitespace between the property name and its value.
* tag 'arm-soc/for-5.20/devicetree' of https://github.com/Broadcom/stblinux: (35 commits)
ARM: dts: Add BCM63138 generic board dts
ARM: dts: update dts files for bcmbca SoC BCM63138
ARM: dts: Move BCM963138DVT board dts to ARCH_BCMBCA
dt-bindings: arm: add BCM63138 SoC
ARM: dts: bcm2711: Use proper compatible in PM/Watchdog node
ARM: dts: bcm2835/bcm2711: Introduce reg-names in watchdog node
dt-bindings: soc: bcm: bcm2835-pm: Add support for bcm2711
dt-bindings: soc: bcm: bcm2835-pm: Introduce reg-names
dt-bindings: soc: bcm: bcm2835-pm: Convert bindings to DT schema
ARM: dts: BCM5301X: Add DT for Meraki MR26
dt-bindings: ARM: add bindings for the Meraki MR26
dt-bindings: arm64: Add BCM6813 SoC
ARM: dts: Add DTS files for bcmbca SoC BCM63148
dt-bindings: arm: Add BCM63148 SoC
dt-bindings: arm64: Add BCM6856 SoC
dt-bindings: arm64: Add BCM63146 SoC
ARM: dts: broadcom: correct gpio-keys properties
ARM: dts: broadcom: align gpio-key node names with dtschema
ARM: dts: Add DTS files for bcmbca SoC BCM6756
dt-bindings: arm: Add BCM6756 SoC
...
Link: https://lore.kernel.org/r/20220711164451.3542127-4-f.fainelli@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm ARM64 DTS updates for v5.20
This introduces initial support for Lenovo ThinkPad X13s, Qualcomm 8cx
Gen 3 Compute Reference Device, SA8295P Automotive Development Platform,
Xiaomi Mi 5s Plus, five new SC7180 Chrome OS boards, Inforce IFC6560, LG
G7 ThinQ and LG V35 ThinQ.
With IPQ8074 gaining GDSC support, this was expressed in the gcc node
and defined for the USB nodes. The SDHCI reset line was defined to get
the storage devices into a known state.
For MSM8996 interconnect providers, the second DSI interface, resets for
SDHCI are introduced. Support for the Xiaomi Mi 5s Plus is introduced
and the Dragonboard 820c gains definitions for its LEDs.
The MSM8998 platform changes consists of a various cleanup patches, the
FxTec Pro1 is split out from using the MTP dts and Sony Xperia devices
on the "Yoshino" platform gains ToF sensor.
On SC7180 five new Trogdor based boards are added and the description of
keyboard and detachables is improved.
On the SC7280-based Herobrine board DisplayPort is enabled, SPI flash
clock rate is changed, WiFi is enabled and the modem firmware path is
updated. The Villager boards gains touchscreen, and keyboard backlight.
This introduces initial support for the SC8280XP (aka 8cx Gen 3) and
related automotive platforms are introduced, with support for the
Qualcomm reference board, the Lenovo Thinkpad X13s and the SA8295P
Automotive Development Platform.
In addition to a wide range of smaller fixes on the SDM630 and SDM660
platforms, support for the secondary high speed USB controller is
introduced and the Sony Xperia "Nile" platform gains support for the RGB
status LED. Support for the Inforce IFC6560 board is introduced.
On SDM845 the bandwidth monitor for the CPU subsystem is introduced, to
scale LLCC clock rate based on profiling. CPU and cluster idle states
are switched to OSI hierarchical states. DB845c and SHIFT 6mq gains LED
support and new support for the LG G7 ThinQ and LG V35 ThinQ boards are
added.
DLL/DDR configuration for SDHCI nodes are defined for SM6125.
On SM8250 the GPU per-process page tables is enabled and for RB5 the
Light Pulse Generator-based LEDs are added.
The display clock controller is introduced for SM8350.
On SM8450 this introduces the camera clock controller and the UART
typically used for Bluetooth. The interconnect path for the crypto
engine is added to the SCM node, to ensure this is adequately clocked.
The assigned-clock-rate for the display processor is dropped from
several platforms, now that the driver derrives the min and max from the
clock.
In addition to this a wide range of fixes for stylistic issues and
issues discovered through Devicetree binding validation across many
platforms and boards are introduced.
* tag 'qcom-arm64-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (193 commits)
arm64: dts: qcom: sc8280xp: fix DP PHY node unit addresses
arm64: dts: qcom: sc8280xp: fix usb_0 HS PHY ref clock
arm64: dts: qcom: sc7280: fix PCIe clock reference
docs: arm: index.rst: add google/chromebook-boot-flow
arm64: dts: qcom: msm8996: clean up PCIe PHY node
arm64: dts: qcom: msm8996: use non-empty ranges for PCIe PHYs
arm64: dts: qcom: sm8450: drop UFS PHY clock-cells
arm64: dts: qcom: sm8250: drop UFS PHY clock-cells
arm64: dts: qcom: sc8280xp: drop UFS PHY clock-cells
arm64: dts: qcom: sm8450: drop USB PHY clock index
arm64: dts: qcom: sm8350: drop USB PHY clock index
arm64: dts: qcom: msm8998: drop USB PHY clock index
arm64: dts: qcom: ipq8074: drop USB PHY clock index
arm64: dts: qcom: ipq6018: drop USB PHY clock index
arm64: dts: qcom: sm8250: add missing PCIe PHY clock-cells
arm64: dts: qcom: sc7280: drop PCIe PHY clock index
Revert "arm64: dts: qcom: Fix 'reg-names' for sdhci nodes"
arm64: dts: qcom: sc7180-idp: add vdds supply to the DSI PHY
arm64: dts: qcom: sc7280: use constants for gpucc clocks and power-domains
arm64: dts: qcom: msm8996: add missing DSI clock assignments
...
Link: https://lore.kernel.org/r/20220713203939.1431054-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm DTS updates for v5.20
This adds USB, NAND, QPIC BAM, CPUfreq, remoteprocs, SMEM, SCM,
watchdog, interconnect providers to the SDX65 5G modem platform and
enables relevant devices for the MTP.
The BAM DMUX interface used to exchange Ethernet/IP data with the modem
is described on the MSM8974 platform.
It fixes up the PXO supply clock to L2CC on IPQ6084, as the platform is
transitioned away from global clock lookup.
SDX55 has it's debug UART interrupt level corrected.
Lastly it contains a wide variety of fixes for DeviceTree validation
issues across most of the platforms.
* tag 'qcom-dts-for-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux: (48 commits)
ARM: dts: qcom: msm8974: rename GPU's OPP table node
ARM: dts: qcom: apq8064: disable DSI and DSI PHY by default
ARM: dts: qcom: apq8064: rename DSI PHY iface clock
ARM: dts: qcom: extend scm compatible to match dt-schema
ARM: dts: qcom: Fix sdhci node names - use 'mmc@'
ARM: dts: qcom: apq8064: drop phy-names from HDMI device node
ARM: dts: qcom: apq8064-ifc6410: drop hdmi-mux-supply
ARM: dts: qcom: pm8841: add required thermal-sensor-cells
ARM: dts: qcom: msm8974: add required ranges to OCMEM
ARM: dts: qcom: sdx55: add dedicated IMEM and syscon compatibles
ARM: dts: qcom: msm8974: add dedicated IMEM compatible
ARM: dts: qcom: apq8064-asus-nexus7: add dedicated IMEM compatible
ARM: dts: qcom: use generic sram as name for imem and ocmem nodes
ARM: dts: qcom: ipq8064: add function to LED nodes
ARM: dts: qcom: ipq8064-rb3011: add color to LED node
ARM: dts: qcom: ipq4018-ap120c-ac: add function and color to LED nodes
ARM: dts: qcom: apq8060-ifc6410: add color to LED node
ARM: dts: qcom: apq8060-dragonboard: add function and color to LED nodes
ARM: dts: qcom: sdx55: Fix the IRQ trigger type for UART
ARM: dts: qcom-msm8974: fix irq type on blsp2_uart1
...
Link: https://lore.kernel.org/r/20220713032024.1372427-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX arm64 device tree update for 5.20:
- Add device tree support for i.MX93 SoC.
- New board device tree: TQMa8MPQL, DH electronics i.MX8M Plus DHCOM and
PDK2, i.MX93 11x11 EVK, phyBOARD-Polis-i.MX8MM.
- A series from Abel Vesa and Viorel Suman to fix i.MX8QXP device tree
to comply with DT schema.
- Disable job ring 0 device for i.MX8MM to avoid caam_jr probe error, due
to that JR0 reservation is done in both upstream (v2.7) and downstream
(NXP lf_v2.4) TF-A.
- A series from Krzysztof Kozlowski to align gpio-key and LED node names
with dtschema.
- Add SNVS LPGPR device for i.MX8MM so that some preserving registers
becomes available as NVMEM.
- Add NoC device support for i.MX8MP SoC.
- A couple of changes from Sean Anderson to add SFP node for TA devices
for LayerScape SoCs.
- A series from Shengjiu Wang to enable bt-sco sound card support for
NXP i.MX8M EVK boards.
- Other small and random board updates.
* tag 'imx-dt64-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (33 commits)
arm64: dts: freescale: add initial device tree for TQMa8MPQL with i.MX8MP
arm64: dts: freescale: imx8qxp: Fix the keys node name
arm64: dts: freescale: imx8: Fix the system-controller node name
arm64: dts: freescale: imx8qxp: Fix the ocotp node name
arm64: dts: freescale: imx8qxp: Add fallback compatible for clock controller
arm64: dts: freescale: imx8: Fix power controller name
arm64: dts: freescale: imx8qxp: Remove unnecessary clock related entries
arm64: dts: imx8mp: add NoC node
arm64: dts: Add SFP node for TA 3.0 devices
arm64: dts: layerscape: Add SFP node for TA 2.1 devices
arm64: dts: freescale: Add phyBOARD-Polis-i.MX8MM support
arm64: dts: imx8m{m,p}-verdin: use IT temperatures
arm64: dts: imx8mn-evk: add bt-sco sound card support
arm64: dts: imx8mq-evk: add bt-sco sound card support
arm64: dts: imx8mm-evk: add bt-sco sound card support
arm64: freescale/imx8mp-evk.dts: reorder nodes alphabetically
arm64: dts: imx8mq: Pass a label to the AIPS nodes
arm64: dts: imx8m: Pass a label to the soc node
arm64: dts: imx8mm-venice-gw7902: fix UART1 CTS
arm64: dts: imx8mp: Add support for DH electronics i.MX8M Plus DHCOM and PDK2
...
Link: https://lore.kernel.org/r/20220709082951.15123-5-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
i.MX device tree change for 5.20:
- A series from Alexander Stein to fix some i.MX6UL dt_binding_check
warnings.
- Replace deprecated 'enable-sdio-wakeup' property with 'wakeup-source'
for a couple of boards.
- A set of imx7-colibri device tree updates from Marcel Ziswiler to
improve devices Display, Touch, Ethernet and SD/MMC, and also adds
Toradex Iris carrier board.
- A few improvements on imx6qdl-colibri board, correct SGTL5000 MCLK
handling, simplify handling of inverted PWM backlight.
- A series from Max Krummenacher (and Oleksandr Suvorov) to improve the
existing i.MX6 Apalis carrier board device trees and adds a new device
tree for the Ixora V1.2 carrier board.
- Add USB dual-role switching using extcon for imx7-colibri board.
- Add SFP node for TA 2.1 devices for LayerScape SoCs.
- Other small and random updates on various boards.
* tag 'imx-dt-5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (61 commits)
ARM: dts: layerscape: Add SFP node for TA 2.1 devices
ARM: dts: imx6qdl-prti6q.dtsi: Add applicable properties to usdhc3
ARM: dts: imx6q-bosch-acc: Replace 'enable-sdio-wakeup'
ARM: dts: imx7d-smegw01: Replace 'enable-sdio-wakeup'
ARM: dts: imx6q-apalis: Cleanup
ARM: dts: imx6q-apalis: backlight pwm: Adapt brightness steps
ARM: dts: imx6q-apalis: backlight pwm: Simplify inverted backlight
ARM: dts: imx6q-apalis: Add support for Toradex Ixora V1.2 carrier boards
ARM: dts: imx6q-apalis: Clean-up sd card support
ARM: dts: imx6q-apalis: Add adv7280 video input
ARM: dts: imx6q-apalis: Add ov5640 mipi csi camera
ARM: dts: imx6q-apalis: Disable stmpe touchscreen
ARM: dts: imx6q-apalis: Disable HDMI
ARM: dts: imx6q-apalis: Add LVDS panel support
ARM: dts: imx6q-apalis: move gpio-keys to SoM dtsi
ARM: dts: imx6q-apalis: Move Atmel MXT touch ctrl to SoM dtsi
ARM: dts: imx6q-apalis: Move pinmux groups to SoM dtsi
ARM: dts: imx6q-apalis: Move parallel rgb interface to SoM dtsi
ARM: dts: imx6q-apalis: Command pmic to standby for poweroff
ARM: dts: imx6q-apalis: Add gpio-line-names
...
Link: https://lore.kernel.org/r/20220709082951.15123-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
arm64: tegra: Device tree changes for v5.20-rc1
This adds and enables various hardware on Tegra234 (host1x, VIC, GPCDMA)
as well as the Control BackBone related device tree nodes on Tegra194
and Tegra234.
Native timers are enabled on Tegra186, Tegra194 and Tegra234, which
allow keeping track of SoC-wide timestamps as well as hardware watchdog
functionality.
The audio subsystem is enhanced with the Output Processing Engine (OPE)
on Tegra210 and later.
Finally there are a handful of minor cleanups and fixes.
* tag 'tegra-for-5.20-arm64-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
arm64: tegra: Fix SDMMC1 CD on P2888
arm64: tegra: Update compatible for Tegra234 GPCDMA
arm64: tegra: Add Host1x and VIC on Tegra234
arm64: tegra: Add Host1x context stream IDs on Tegra186+
arm64: tegra: Enable native timers on Tegra234
arm64: tegra: Enable native timers on Tegra194
arm64: tegra: Enable native timers on Tegra186
arm64: tegra: Add node for CBB 2.0 on Tegra234
arm64: tegra: Add node for CBB 1.0 on Tegra194
arm64: tegra: Align gpio-keys node names with dtschema
arm64: tegra: Mark BPMP channels as no-memory-wc
arm64: tegra: Add Tegra234 GPCDMA device tree node
arm64: tegra: Adjust whitespace around '='
arm64: tegra: Enable OPE on various platforms
arm64: tegra: Add OPE device on Tegra210 and later
Link: https://lore.kernel.org/r/20220708185608.676474-7-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
ARM: tegra: Device tree changes for v5.20-rc1
Two minor fixes to help reduce the noise from the DT validation tooling.
* tag 'tegra-for-5.20-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Align gpio-keys node names with dtschema
ARM: tegra: Adjust whitespace around '='
Link: https://lore.kernel.org/r/20220708185608.676474-6-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
dt-bindings: Changes for v5.20-rc1
These changes add clock, reset, memory client and power domain
definitions for various devices found on Tegra234 along with a few
device tree bindings for new hardware.
* tag 'tegra-for-5.20-dt-bindings' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: tegra-ccplex-cluster: Remove status from required properties
dt-bindings: Add headers for Host1x and VIC on Tegra234
dt-bindings: timer: Add Tegra186 & Tegra234 Timer
dt-bindings: arm: tegra: Add NVIDIA Tegra234 CBB 2.0 binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 AXI2APB binding
dt-bindings: arm: tegra: Add NVIDIA Tegra194 CBB 1.0 binding
dt-bindings: memory: Add Tegra234 MGBE memory clients
dt-bindings: Add Tegra234 MGBE clocks and resets
dt-bindings: power: Add Tegra234 MGBE power domains
dt-bindings: Add headers for Tegra234 GPCDMA
Link: https://lore.kernel.org/r/20220708185608.676474-4-thierry.reding@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Airoha EN7523:
- Add clock and PCIe support
Several style fixes to comply with DT spec.
* tag 'v5.19-next-dts32' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
ARM: dts: mediatek: align gpio-key node names with dtschema
ARM: dts: mediatek: adjust whitespace around '='
ARM: dts: Add PCIe support for Airoha EN7523
ARM: dts: add clock support for Airoha EN7523
Link: https://lore.kernel.org/r/63536da6-fbe4-2d96-ab91-ae756cd580c4@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The X96 Mate is an Allwinner H616 based TV box, featuring:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 2GiB/4GiB RAM (fully usable!)
- 16/32/64GiB eMMC
- 100Mbps Ethernet (via embedded AC200 EPHY, not yet supported)
- Unsupported Allwinner WiFi chip
- 2 x USB 2.0 host ports
- HDMI port
- IR receiver
- 5V/2A DC power supply via barrel plug
Add a basic devicetree for it, with SD card and eMMC working, as
well as serial and the essential peripherals, like the AXP PMIC.
This DT is somewhat minimal, and should work on many other similar TV
boxes with the Allwinner H616 chip.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-8-andre.przywara@arm.com
The OrangePi Zero 2 is a development board with the new H616 SoC. It
comes with the following features:
- Four ARM Cortex-A53 cores, Mali-G31 MP2 GPU
- 512MiB/1GiB DDR3 DRAM
- AXP305 PMIC
- Raspberry-Pi-1 compatible GPIO header
- extra 13 pin expansion header, exposing pins for 2x USB 2.0 ports
- 1 USB 2.0 host port
- 1 USB 2.0 type C port (power supply + OTG)
- MicroSD slot
- on-board 2MiB bootable SPI NOR flash
- 1Gbps Ethernet port (via RTL8211F PHY)
- micro-HDMI port
- (yet) unsupported Allwinner WiFi/BT chip
Add the devicetree file describing the currently supported features.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-7-andre.przywara@arm.com
This (relatively) new SoC is similar to the H6, but drops the (broken)
PCIe support and the USB 3.0 controller. It also gets the management
controller removed, which in turn removes *some*, but not all of the
devices formerly dedicated to the ARISC (CPUS).
And while there is still the extra sunxi interrupt controller, the
package lacks the corresponding NMI pin, so no interrupts for the PMIC.
The reserved memory node is actually handled by Trusted Firmware now,
but U-Boot fails to propagate this to a separately loaded DTB, so we
keep it in here for now, until U-Boot learns to do this properly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-4-andre.przywara@arm.com
The R_PIO pinctrl device on the Allwinner H616 SoC does not have an
interrupt (it features only two pins).
However the binding requires at least naming one upstream interrupt,
plus the #interrupt-cells and interrupt-controller properties.
Drop the unconditional requirement for the interrupt properties, and
make them dependent on being not this particular pinctrl device.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Link: https://lore.kernel.org/r/20220708105235.3983266-3-andre.przywara@arm.com
TQMa8MPxL is a SOM family using NXP i.MX8MP CPU family
MBa8MPxL is an evaluation mainbord for this SOM
The SOM needs a mainboard, therefore we provide two compatibles here:
"tq,imx8mp-<SOM>" for the module and
"tq,imx8mp-<SOM>-<SBC>"
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use CONFIG_ARCH_BCMBCA to build all the BCMBCA SoC dts and remove
CONFIG_ARCH_BCM_63XX from the makefile
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
