This patch adds dt bindings to enable netcp network driver on K2G
ICE boards. This consists of enabling bindings for NSS qmss, pktdma,
2u ethss, mdio, pinmux and netcp devices as well as DP83867 phy.
EVM hardware spec recommends to add 0.25 nsec delay in the tx direction
and 2.25 nsec delay in the rx direction for internal delay in the clock
path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode 1.
The phy data manual disallows this. Add ti,dp83867-rxctrl-strap-quirk
in the phy node to allow software to enable the workaround suggested for
this incorrect strap setting. This ensures proper operation of this PHY.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This patch add dt bindings to support network driver based on
Network Sub System (NSS) found on k2g SoC. This consists of
bindings for netcp node, nss qmss , pktdma, cpsw 2u version
of ethss and mdio.
In order to support transitioning between non-promiscuous
and promiscuous modes in K2G's ethernet switch, netcp ALE
needs to be enabled. Therefore this patch enables K2G's
netcp ALE for that purpose.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
This adds clock provider nodes for da850 and wires them up to all of the
devices.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add support for RTC (Real Time Clock) to STM32MP157C SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Remove no longer needed samsung thermal properties.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Secondary CPUs should have the same information in DeviceTree as booting
CPU from both correctness point of view and for possible hotplug
scenarios.
Suggested-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add activation of the Controller Area Network m_can on stm32mp157c-ev1
board.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the Controller Area Network m_can to STM32MP157C SoC.
Signed-off-by: Bich Hemon <bich.hemon@st.com>
Signed-off-by: Erwan Le Ray <erwan.leray@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
To fit with latest rtc driver updates, rtc st,syscfg property must contain
the control register offset of pwrcfg and the mask corresponding to the
DBP (Disable Backup Protection) bit.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
To fit with latest rtc driver updates, rtc st,syscfg property must contain
the control register offset of pwrcfg and the mask corresponding to the
DBP (Disable Backup Protection) bit.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
4.18, please pull the following:
- Ray fixes the I2C and PCIe interrupt types for the Cygnus SoC
- Florian fixes the I2C and PCIe interrupts for the Northstar
(BCM5301x), Northstar Plus and Hurricane 2 SoCs
-----BEGIN PGP SIGNATURE-----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=0JyZ
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.18/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-based SoCs Device Tree fixes for
4.18, please pull the following:
- Ray fixes the I2C and PCIe interrupt types for the Cygnus SoC
- Florian fixes the I2C and PCIe interrupts for the Northstar
(BCM5301x), Northstar Plus and Hurricane 2 SoCs
* tag 'arm-soc/for-4.18/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: Cygnus: Fix PCIe controller interrupt type
ARM: dts: Cygnus: Fix I2C controller interrupt type
ARM: dts: BCM5301x: Fix i2c controller interrupt type
ARM: dts: HR2: Fix interrupt types for i2c and PCIe
ARM: dts: NSP: Fix PCIe controllers interrupt types
ARM: dts: NSP: Fix i2c controller interrupt type
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix i.MX6SX PCIe MSI interrupt number, so that MSI IRQs can be
properly propagated to the upstream interrupt controller.
- Fix GPCv2 MIPI/PCIe/USB_HSIC's PGC offset. The values in Reference
Manual are incorrect.
- Correct SDMA setting for i.MX6Q SPI5 device to fix the issue, that
the SPI controller RX FIFO was not empty after a DMA transfer, and
the driver gets stuck in the next PIO transfer when reading one word
more than expected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbKLcnAAoJEFBXWFqHsHzO8dMH/ijDSZf172X9jls8iQgcFQ8h
ZAnIj+T23j9L8CTHBx5OLgUxaHYgX410HYvqWuubCNDKv+DMCP+7QNE6v+iSehhT
8sA4dX5296orNb9d5dXyf0XIZ4dA1ljhoZUY6r9DHGFfkIriHwX6HB0zl9EmroAK
mVMGeltfGqPCZ6bH1O6L4oCZNfaOmqBz1f767Es4uxD0IzPg/9BlarqLgASu+op1
1KVFGKY/o4S6QrMxrLxlsrqFUx1DmRQyWxtKYyPlkY6LIHeiJNMCLh9NzW+/qGHf
keycpIjVdlVdZMILDeTju3gszoOmXjq0L1XP9Ityf9OLq53c1Ypsn9npK2ccZNU=
=lalT
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.18:
- Fix i.MX6SX PCIe MSI interrupt number, so that MSI IRQs can be
properly propagated to the upstream interrupt controller.
- Fix GPCv2 MIPI/PCIe/USB_HSIC's PGC offset. The values in Reference
Manual are incorrect.
- Correct SDMA setting for i.MX6Q SPI5 device to fix the issue, that
the SPI controller RX FIFO was not empty after a DMA transfer, and
the driver gets stuck in the next PIO transfer when reading one word
more than expected.
* tag 'imx-fixes-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6sx: fix irq for pcie bridge
soc: imx: gpcv2: correct PGC offset
ARM: dts: imx6q: Use correct SDMA script for SPI5 core
Signed-off-by: Olof Johansson <olof@lixom.net>
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWwwZggAKCRALBhiOFHI7
1RZ3AJ4wjqNwkBmHpxD5DDQgNcO1WxYhFgCffMYB3qCIdYW6ROiFCs79bq/8Ldc=
=HA77
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.17 (part 2)
- Use correct size for ICU nodes (irq controller) on Armada 7K/8K
- Fix "#cooling-cells" property's name on Synology DS116 (Armada 385)
* tag 'mvebu-fixes-4.17-2' of git://git.infradead.org/linux-mvebu:
arm: dts: armada: Fix "#cooling-cells" property's name
arm64: dts: marvell: fix CP110 ICU node size
Signed-off-by: Olof Johansson <olof@lixom.net>
The Raspberry Pi Compute Module (CM1) is a SoM which contains a
BCM2835 processor, 512 MB RAM and a 4 GB eMMC. There is also a carrier
board which is called Compute Module IO Board.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Eric Anholt <eric@anholt.net>
Make each SoC dtsi use its soc specific PMc compatible string. This solves
a potential issue on at91sam9261 and at91sam9263 when using suspend to RAM
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Use the correct IRQ line for the MSI controller in the PCIe host
controller. Apparently a different IRQ line is used compared to other
i.MX6 variants. Without this change MSI IRQs aren't properly propagated
to the upstream interrupt controller.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: b1d17f68e5 ("ARM: dts: imx: add initial imx6sx device tree source")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Two different regulators are defined with the same name and label but
distinct properties.
The first definition was added with the first board dts and the second
was added when upstream added flexcan support.
Looking at schematics it is indeed gpio2 14 connected to the STB pin of
the CAN transceiver so remove the first definition.
The second definition entirely overrides the first so this already
worked and this patch results in no DTB change, just a cleanup.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The following sensors are on I2C3 on the baseboard:
* isil,isl29023 light sensor
* fsl,mag3110 magnetometer
* fsl,mma8451 accelerometer
Added under i2cmux/i2c@1 because they're not otherwise accessible.
These are all supported by iio with following configs:
* CONFIG_SENSORS_ISL29018
* CONFIG_MAG3110
* CONFIG_MMA8452
Tested with raw reads from iio sysfs.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- in reg_2p5, fix regulator node name as regulator-2p5v
- remove exctra line
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OV5640 Camera sensor is connected in i.CoreM6 1.5 Quad/Dual MIPI
starter kit.
This patch also move MX6QDL_PAD_GPIO_0__CCM_CLKO1 pinctrl
from i2c3 to ov5640 pinctrl.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The RMI4 touchscreen driver applied inversion and axis swap in the
wrong order, violating the DT binding for those properties. This is
fixed now, so correct the RDU2 DT to apply the inversion to the
correct axis.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix PCIe controller interrupt to use IRQ_TYPE_LEVEL_HIGH for Broadcom
Cygnus SoC
Fixes: cd590b50a9 ("ARM: dts: enable PCIe support for Cygnus")
Fixes: f6b889358a ("ARM: dts: Enable MSI support for Broadcom Cygnus")
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should be using IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: bb097e3e00 ("ARM: dts: BCM5301X: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c and PCIe controllers had an incorrect type which should have
been set to IRQ_TYPE_LEVEL_HIGH, fix that.
Fixes: b9099ec754 ("ARM: dts: Add Broadcom Hurricane 2 DTS include file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The interrupts for the PCIe controllers should all be of type
IRQ_TYPE_LEVEL_HIGH instead of IRQ_TYPE_NONE.
Fixes: d71eb94120 ("ARM: dts: NSP: Add MSI support on PCI")
Fixes: 522199029f ("ARM: dts: NSP: Fix PCIE DT issue")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The i2c controller should use IRQ_TYPE_LEVEL_HIGH instead of
IRQ_TYPE_NONE.
Fixes: 0f9f27a36d ("ARM: dts: NSP: Add I2C support to the DT")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
When using the board files the LCD works, but not with the DT.
This adds enables the original da850-evm to work with the same
LCD in device tree mode.
The EVM has a gpio for backlight regulator and a PWM for dimming
the backlight. The LCD and the vpif display pins are mutually
exclusive, so if using the LCD, do not load the vpif driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The DA850-EVM from Logic PD has a SATA port and the module that went
with the kit supports it as well. This patch enables SATA controller.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[follow conversion to operating-points-v2]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Operating points need to be present in each cpu core using it, not only
the first one. With operating-points-v1 this would require duplicating
this table into each cpu node.
With opp-v2 we can share the same table on all nodes.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Add PMIC nodes to Porter and connect CPU DVFS supply. There is
one DA9063L and one DA9210 on Porter, the only difference from
the other boards is that DA9063L is at I2C address 0x5a rather
than 0x58 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, clock-names) as well to make it all
work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Fix other missing properties (clocks, OPP, clock latency) as well to
make it all work.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The cooling device properties, like "#cooling-cells" and
"dynamic-power-coefficient", should either be present for all the CPUs
of a cluster or none. If these are present only for a subset of CPUs of
a cluster then things will start falling apart as soon as the CPUs are
brought online in a different order. For example, this will happen
because the operating system looks for such properties in the CPU node
it is trying to bring up, so that it can register a cooling device.
Add such missing properties.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Update all 32bit rockchip devicetree files to use SPDX-License-Identifiers.
All files except rk3288-veyron-analog-audio.dtsi (which is GPL 2.0 only)
claim to be GPL and X11 while the actual license text is MIT. Use the
MIT SPDX tag for them.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Brian Norris <briannorris@chromium.org>
Acked-by: Matthias Brugger <mbrugger@suse.com>
Acked-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The updated dtc emits a warning for the edp-panel of two rk3288 boards:
Warning (graph_endpoint): /dp@ff970000/ports/port@1/endpoint: graph node unit address error, expected "0"
Fix this by adding the necessary @0 to the endpoint node.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
USB OTG power is switched on when the GPIO is pulled low.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable USB OTG (dual-role) on the Wandboard.
Note, that the USB_OTG_VBUS current is quite limited due to a 22R resistor
in the power line. Hence, the overcurrent signal of 1A will never be
triggered on this board.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
To match the convention, move all regulator-fixed nodes directly into
the root node.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Make sure that MX51_PAD_GPIO1_1 does not remain configure as
ALT0/SD1_WP (it is out of reset). This is needed because of external
pull-up resistor attached to that pad that, when left unchanged, will
drive SD1_WP high preventing eSDHC1/eMMC from working correctly.
To fix that add a pinmux configuration line configureing the pad to
function as a GPIO. While we are at it, add a corresponding
output-high GPIO hog in an effort to minimize current consumption.
Cc: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Tested-By: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit provides support for HSC and DDC boards from
Kieback&Peter GmbH vendor.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to the reference manual the shp_2_mcu / mcu_2_shp
scripts must be used for devices connected through the SPBA.
This fixes an issue we saw with DMA transfers.
Sometimes the SPI controller RX FIFO was not empty after a DMA
transfer and the driver got stuck in the next PIO transfer when
it read one word more than expected.
commit dd4b487b32 ("ARM: dts: imx6: Use correct SDMA script
for SPI cores") is fixing the same issue but only for SPI1 - 4.
Fixes: 677940258d ("ARM: dts: imx6q: enable dma for ecspi5")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds support for an optional device-tree property that
makes the driver skip all the delays around clocking the
GPIOs and set it in the device-tree of common POWER9 based
OpenPower platforms.
This useful on chips like the AST2500 where the GPIO block is
running at a fairly low clock frequency (25Mhz typically). In
this case, the delays are unnecessary and due to the low
precision of the timers, actually quite harmful in terms of
performance.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Christopher Bostic <cbostic@linux.vnet.ibm.com>
Tested-by: Joel Stanley <joel@jms.id.au>
This is a branch with a few merge requests that either came in late, or
took a while longer for us to review and merge than usual and thus cut
it a bit close to the merge window. We stage them in a separate branch
and if things look good, we still send them up -- and that's the case
here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface.
-----BEGIN PGP SIGNATURE-----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=RUL0
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late updates from Olof Johansson:
"This is a branch with a few merge requests that either came in late,
or took a while longer for us to review and merge than usual and thus
cut it a bit close to the merge window. We stage them in a separate
branch and if things look good, we still send them up -- and that's
the case here.
This is mostly DT additions for Renesas platforms, adding IP block
descriptions for existing and new SoCs.
There are also some driver updates for Qualcomm platforms for SMEM/QMI
and GENI, which is their generalized serial protocol interface"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (186 commits)
soc: qcom: smem: introduce qcom_smem_virt_to_phys()
soc: qcom: qmi: fix a buffer sizing bug
MAINTAINERS: Update pattern for qcom_scm
soc: Unconditionally include qcom Makefile
soc: qcom: smem: check sooner in qcom_smem_set_global_partition()
soc: qcom: smem: fix qcom_smem_set_global_partition()
soc: qcom: smem: fix off-by-one error in qcom_smem_alloc_private()
soc: qcom: smem: byte swap values properly
soc: qcom: smem: return proper type for cached entry functions
soc: qcom: smem: fix first cache entry calculation
soc: qcom: cmd-db: Make endian-agnostic
drivers: qcom: add command DB driver
arm64: dts: renesas: salvator-common: Add ADV7482 support
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
arm64: dts: renesas: salvator-common: enable VIN
arm64: dts: renesas: r8a77970: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a77965: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7796: add VIN and CSI-2 nodes
arm64: dts: renesas: r8a7795-es1: add CSI-2 node
...
As always, a large number of DT updates. Too many to enumerate them all,
but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some set
top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other on-chip
ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current high-end
mobile SoCs.
It's great to see mainline support for it. So far, you
can't do much with it, since a lot of peripherals are not yet in the
DTs but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC upstream if
the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive entertainment-targeted
SoC. Currently only one Cortex-A53 CPU is enabled, we are eagerly
awaiting more. So far, basic drivers such as serial, gpios, PMU and
ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and ethernet
enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions might
not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support
-----BEGIN PGP SIGNATURE-----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=jLvk
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates from Olof Johansson:
"As always, a large number of DT updates. Too many to enumerate them
all, but at a glance:
New SoCs introduced in this release:
- Amlogic:
+ Meson 8M2 SoC, a.k.a. S812. A quad Cortex-A9 SoC used in some
set top boxes and other products.
- Mediatek:
+ MT7623A, which is a flavor of the MT7623 family with other
on-chip ethernet options.
- Qualcomm:
+ SDM845, a.k.a Snapdragon 845, an 4+4-core Kryo 385/845
(Cortex-A75/A55 derivative) SoC that's one of the current
high-end mobile SoCs.
It's great to see mainline support for it. So far, you can't do
much with it, since a lot of peripherals are not yet in the DTs
but driver support for USB, GPU and other pieces are starting to
trickle in. This might end up being a well-supported SoC
upstream if the momentum keeps up.
- Renesas:
+ R8A77990, a.k.a R-Car E3, a new automotive
entertainment-targeted SoC. Currently only one Cortex-A53 CPU is
enabled, we are eagerly awaiting more. So far, basic drivers
such as serial, gpios, PMU and ethernet are enabled.
+ R8A77470, a.k.a. RZ/G1C, a new dual Cortex-A7 SoC with PowerVR
GPU. Same here, basic set of drivers such as serial, gpios and
ethernet enabled, and SMP support is also forthcoming.
- STMicroelectronics:
+ STM32F469, very similar tih STM32F429 but with display support
Enhancements to SoCs/platforms (DTS contents, some driver portions
might not be in yet):
- Allwinner sun8i (h3/a33/a83t) SMP, DVFS tweaks, misc
- Amlogic Meson: I2C, UFS, TDM, GPIO external interrupts, MMC resets
- Hisilicon hi3660: Thermal cooling, CPU frequency scaling, mailbox interfaces
- Marvell Berlin2CD: SMP support, thermal sensors
- Mediatek MT7623: Highspeed DMA, audio support
- Qualcomm IPQ8074 PCIe support, MSM8996 UFS support
- Renesas: Watchdog and PMU support across many platforms
- Rockchip RK3399: USB3 OTG support
- Samsung Exynos: Audio-over-HDMI on Odroid X/X2/U3
- STMicro STM32: Lots of peripherals added to STM32MP175C
- Uniphier: Ethernet support
New boards:
- Allwinner A20: Olimex A20-SOM-EVB-eMMC variant
- Allwinner H2+: Libre Computer ALL-H3-CC (h2+ version)
- Allwinner A33: Nintendo NES/SuperNES Classic Edition
- Aspeed: S2600WF, Inventec Lanyang BMC, Portwell Neptune
- Berlin2CD: Valve Steam Link
- Broadcom BCM5301X: Luxul XAP-1610 and XWR-3150 V1
- Broadcom: Raspberry Pi 3 B+
- Mediatek MT7623N and MT7623A: reference boards
- Meson 8M2: Tronsmart MXIII Plus
- NXP i.MX: Engicam i.CoreM6, DHCOM iMX6 SOM, BTicino i.MX6DL Mamoj
- Qualcomm MSM8974: Sony Xperia Z1 Compact support
- Qualcomm SDM845: MTP development board
- Renesas: Ebisu R8A77990 board
- Renesas RZ/G1C: iwg23s: iWave G235-SDB
- TI am335x: Pocketbeagle support"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (448 commits)
ARM: dts: aspeed: Fix hwrng register address
arm64: dts: sprd: whale2: Add the rtc enable clock for watchdog
arm64: dts: sprd: Add GPIO and GPIO keys device nodes
arm64: dts: sprd: fix typo in 'remote-endpoint'
arm64: dts: apq8096-db820c: Removed bt-en-1-8v regulator
arm64: dts: fix regulator property name for wlan pcie endpoint
arm64: dts: qcom: msm8996: Use UFS_GDSC for UFS
ARM: dts: pxa3xx: fix MMC clocks
ARM: pxa: dts: add pin definitions for extended GPIOs
ARM: pxa: dts: add gpio-ranges to gpio controller
ARM: dts: ipq8074: Enable few peripherals for hk01 board
ARM: dts: ipq8074: Add pcie nodes
ARM: dts: ipq8074: Add peripheral nodes
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c2 board file
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk07.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk07.1 common data
ARM: dts: ipq4019: Add qcom-ipq4019-ap.dk04.1-c3 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.1-c1 board file
ARM: dts: ipq4019: Add ipq4019-ap.dk04.dtsi
ARM: dts: ipq4019: Change the max opp frequency
...
general cleanups, but nothing too major. The majority of the diff goes to
two SoCs, Actions Semi and Qualcomm. A brand new driver is introduced for
Actions Semi so it takes up some lines to add all the different types, and
the Qualcomm diff is there because we add support for two SoCs and it's quite
a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic platforms. And
then the long tail of driver updates for various fixes and stuff follows
after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock
-----BEGIN PGP SIGNATURE-----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=KK/v
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This time we have a good set of changes to the core framework that do
some general cleanups, but nothing too major. The majority of the diff
goes to two SoCs, Actions Semi and Qualcomm. A brand new driver is
introduced for Actions Semi so it takes up some lines to add all the
different types, and the Qualcomm diff is there because we add support
for two SoCs and it's quite a bit of data.
Otherwise the big driver updates are on TI Davinci and Amlogic
platforms. And then the long tail of driver updates for various fixes
and stuff follows after that.
Core:
- debugfs cleanups removing error checking and an unused provider API
- Removal of a clk init typedef that isn't used
- Usage of match_string() to simplify parent string name matching
- OF clk helpers moved to their own file (linux/of_clk.h)
- Make clk warnings more readable across kernel versions
New Drivers:
- Qualcomm SDM845 GCC and Video clk controllers
- Qualcomm MSM8998 GCC
- Actions Semi S900 SoC support
- Nuvoton npcm750 microcontroller clks
- Amlogic axg AO clock controller
Removed Drivers:
- Deprecated Rockchip clk-gate driver
Updates:
- debugfs functions stopped checking return values
- Support for the MSIOF module clocks on Rensas R-Car M3-N
- Support for the new Rensas RZ/G1C and R-Car E3 SoCs
- Qualcomm GDSC, RCG, and PLL updates for clk changes in new SoCs
- Berlin and Amlogic SPDX tagging
- Usage of of_clk_get_parent_count() in more places
- Proper implementation of the CDEV1/2 clocks on Tegra20
- Allwinner H6 PRCM clock support and R40 EMAC support
- Add critical flag to meson8b's fdiv2 as temporary fixup for ethernet
- Round closest support for meson's mpll driver
- Support for meson8b nand clocks and gxbb video decoder clocks
- Mediatek mali clks
- STM32MP1 fixes
- Uniphier LD11/LD20 stream demux system clock"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
clk: qcom: Export clk_fabia_pll_configure()
clk: bcm: Update and add Stingray clock entries
dt-bindings: clk: Update Stingray binding doc
clk-si544: Properly round requested frequency to nearest match
clk: ingenic: jz4770: Add 150us delay after enabling VPU clock
clk: ingenic: jz4770: Enable power of AHB1 bus after ungating VPU clock
clk: ingenic: jz4770: Modify C1CLK clock to disable CPU clock stop on idle
clk: ingenic: jz4770: Change OTG from custom to standard gated clock
clk: ingenic: Support specifying "wait for clock stable" delay
clk: ingenic: Add support for clocks whose gate bit is inverted
clk: use match_string() helper
clk: bcm2835: use match_string() helper
clk: Return void from debug_init op
clk: remove clk_debugfs_add_file()
clk: tegra: no need to check return value of debugfs_create functions
clk: davinci: no need to check return value of debugfs_create functions
clk: bcm2835: no need to check return value of debugfs_create functions
clk: no need to check return value of debugfs_create functions
clk: imx6: add EPIT clock support
clk: mvebu: use correct bit for 98DX3236 NAND
...
Here is the big tty/serial driver update for 4.18-rc1.
There's nothing major here, just lots of serial driver updates. Full
details are in the shortlog, nothing anything specific to call out here.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWxbZzQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ym2pQCggrWJsOeXLXgzhVDH6/qMFP9R/hEAoLTvmOWQ
BlPIlvRDm/ud33VogJ8t
=XS8u
-----END PGP SIGNATURE-----
Merge tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the big tty/serial driver update for 4.18-rc1.
There's nothing major here, just lots of serial driver updates. Full
details are in the shortlog, nothing anything specific to call out
here.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (55 commits)
vt: Perform safe console erase only once
serial: imx: disable UCR4_OREN on shutdown
serial: imx: drop CTS/RTS handling from shutdown
tty: fix typo in ASYNCB_FOURPORT comment
serial: samsung: check DMA engine capabilities before using DMA mode
tty: Fix data race in tty_insert_flip_string_fixed_flag
tty: serial: msm_geni_serial: Fix TX infinite loop
serial: 8250_dw: Fix runtime PM handling
serial: 8250: omap: Fix idling of clocks for unused uarts
tty: serial: drop ATH79 specific SoC symbols
serial: 8250: Add missing rxtrig_bytes on Altera 16550 UART
serial/aspeed-vuart: fix a couple mod_timer() calls
serial: sh-sci: Use spin_{try}lock_irqsave instead of open coding version
serial: 8250_of: Add IO space support
tty/serial: atmel: use port->name as name in request_irq()
serial: imx: dma_unmap_sg buffers on shutdown
serial: imx: cleanup imx_uart_disable_dma()
tty: serial: qcom_geni_serial: Add early console support
tty: serial: qcom_geni_serial: Return IRQ_NONE for spurious interrupts
tty: serial: qcom_geni_serial: Use iowrite32_rep to write to FIFO
...
Pull irq updates from Thomas Gleixner:
- Consolidation of softirq pending:
The softirq mask and its accessors/mutators have many implementations
scattered around many architectures. Most do the same things
consisting in a field in a per-cpu struct (often irq_cpustat_t)
accessed through per-cpu ops. We can provide instead a generic
efficient version that most of them can use. In fact s390 is the only
exception because the field is stored in lowcore.
- Support for level!?! triggered MSI (ARM)
Over the past couple of years, we've seen some SoCs coming up with
ways of signalling level interrupts using a new flavor of MSIs, where
the MSI controller uses two distinct messages: one that raises a
virtual line, and one that lowers it. The target MSI controller is in
charge of maintaining the state of the line.
This allows for a much simplified HW signal routing (no need to have
hundreds of discrete lines to signal level interrupts if you already
have a memory bus), but results in a departure from the current idea
the kernel has of MSIs.
- Support for Meson-AXG GPIO irqchip
- Large stm32 irqchip rework (suspend/resume, hierarchical domains)
- More SPDX conversions
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (36 commits)
ARM: dts: stm32: Add exti support to stm32mp157 pinctrl
ARM: dts: stm32: Add exti support for stm32mp157c
pinctrl/stm32: Add irq_eoi for stm32gpio irqchip
irqchip/stm32: Add suspend/resume support for hierarchy domain
irqchip/stm32: Add stm32mp1 support with hierarchy domain
irqchip/stm32: Prepare common functions
irqchip/stm32: Add host and driver data structures
irqchip/stm32: Add suspend support
irqchip/stm32: Add falling pending register support
irqchip/stm32: Checkpatch fix
irqchip/stm32: Optimizes and cleans up stm32-exti irq_domain
irqchip/meson-gpio: Add support for Meson-AXG SoCs
dt-bindings: interrupt-controller: New binding for Meson-AXG SoC
dt-bindings: interrupt-controller: Fix the double quotes
softirq/s390: Move default mutators of overwritten softirq mask to s390
softirq/x86: Switch to generic local_softirq_pending() implementation
softirq/sparc: Switch to generic local_softirq_pending() implementation
softirq/powerpc: Switch to generic local_softirq_pending() implementation
softirq/parisc: Switch to generic local_softirq_pending() implementation
softirq/ia64: Switch to generic local_softirq_pending() implementation
...
* R-Mobile A1 (r8a7740) SoC
- Describe CEU, IRQC, SYS-DMAC and USB devices
- Cleanup for consistency with other Renesas SoCs and enhanced maintainability
+ Stop grouping clocks under a "clocks" subnode
+ Add soc node
+ Sort subnodes of root and soc nodes
* RZ/A1H (r7s72100) SoC
- Describe CEU device
* R-Car Gen2, RZ/G1 and RZ/A1H SoCs
- Add PMU device nodes
Geert Uytterhoeven says: "This patch series enables support for the ARM
Performance Monitor Units in Cortex-A7, Cortex-A9, and Cortex-A15 CPU
cores on Renesas RZ/A1, R-Car Gen2, and RZ/G1 SoCs. This allows for
better performance analysis using the "perf" tool."
* RZ/A1H (r7s72100) SoC
- Correct interrupt types
Geert Uytterhoeven says "RZ/A1H peripherals use a mix of level and edge
interrupts.
This patch series corrects the interrupt types for watchdog and RTC from
edge to level, to match the datasheet."
* R-Mobile APE6 (r8a73a4) APE4EVM board and SH-Mobile AG5 (sh73a0) SoC
- Use generic disable-wp instead of now deprecated
toshiba,mmc-wrprotect-disable property
* EMMA Mobile EV2 (emev2) and SH-Mobile AG5 (sh73a0) SoCs
- Add missing interrupt-affinity to PMU
Geert Uytterhoeven says "The Cortex-A9 PMU nodes on SH-Mobile AG5 and
Emma Mobile EV2 reference two interrupts, but lack interrupt-affinity
properties, leading to:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
This series adds the missing properties to fix this."
* R-Car H2 (r8a7790) and R-Mobile APE6 (r8a73a4) SoCs
- Correct mask for GIC PPI interrupts
Geert Uytterhoeven says "R-Car H2 and R-Mobile APE6 contain four
Cortex-A15 and four Cortex-A7 cores, hence the second interrupt
specifier cell for Private Peripheral Interrupts should use
"GIC_CPU_MASK_SIMPLE(8)", to make sure interrupts can be delivered to
all 8 processor cores.
This brings the predecessors of R-Car Gen3 in line with what we're
doing on other big.LITTLE SoCs, like R-Car H3 and M3-W."
* Alt board for R-Car E2 (r8a7794) SoC
* RBoards for -Car Gen2 SoCs and kzm9d board for EMMA Mobile EV2 (emev2) SoC
- Drop unnecessary address properties from VIN port nodes
These are unnecessary as the nodes to not have bus addresses.
* R-Car H2 (r8a7790), M2-W (r8a7791), M2-N (r8a7793) and E2 (r8a7794) SoCs
- Describe FDP1 instances
* iW-RainboW-G23S board for RZ/G1C (r8a77470) SoC
- Initial SoC and board support
- Enable EtherAVB
- Describe all SCIF devices
* Boards for R-Car Gen2 SoCs
- Enable watchdog support
Geert Uytterhoeven says "This patch series enables the builtin watchdog
timer on R-Car Gen2 SoCs on all supported boards, and builds on top of
Fabrizio's "[RFC v4 00/26] Fix watchdog on Renesas R-Car Gen2 and
RZ/G1"."
* R-Car Gen2 and RZ/G1 SoCs
- Describe watchdog devices
- For R-Car Gen2 this involves updating the SMP routine side as
it is changed by a driver updated to allow watchdog device support
* Wheat board for V2H (r8a7792) SoC
- Correct ADV7513 address usage
Kieran Bingham says "The r8a7792 Wheat board has two ADV7513 devices
sharing a single I2C bus, however in low power mode the ADV7513 will
reset it's slave maps to use the hardware defined default addresses.
The ADV7511 driver was adapted to allow the two devices to be
registered correctly - but it did not take into account the fault
whereby the devices reset the addresses.
This results in an address conflict between the device using the
default addresses, and the other device if it is in low-power-mode.
Repair this issue by moving both devices away from the default address
definitions."
-----BEGIN PGP SIGNATURE-----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=LV2P
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/late
Renesas ARM Based SoC DT Updates for v4.18
* R-Mobile A1 (r8a7740) SoC
- Describe CEU, IRQC, SYS-DMAC and USB devices
- Cleanup for consistency with other Renesas SoCs and enhanced maintainability
* RZ/A1H (r7s72100) SoC
- Describe CEU device
* R-Car Gen2, RZ/G1 and RZ/A1H SoCs
- Add PMU device nodes
* RZ/A1H (r7s72100) SoC
- Correct interrupt types
* R-Mobile APE6 (r8a73a4) APE4EVM board and SH-Mobile AG5 (sh73a0) SoC
- Use generic disable-wp instead of now deprecated
toshiba,mmc-wrprotect-disable property
* EMMA Mobile EV2 (emev2) and SH-Mobile AG5 (sh73a0) SoCs
- Add missing interrupt-affinity to PMU
* R-Car H2 (r8a7790) and R-Mobile APE6 (r8a73a4) SoCs
- Correct mask for GIC PPI interrupts
* R-Car H2 (r8a7790), M2-W (r8a7791), M2-N (r8a7793) and E2 (r8a7794) SoCs
- Describe FDP1 instances
* R-Car Gen2 and RZ/G1 SoCs
- Describe watchdog devices
- For R-Car Gen2 this involves updating the SMP routine side as
it is changed by a driver updated to allow watchdog device support
* Alt board for R-Car E2 (r8a7794) SoC
* RBoards for -Car Gen2 SoCs and kzm9d board for EMMA Mobile EV2 (emev2) SoC
* iW-RainboW-G23S board for RZ/G1C (r8a77470) SoC
- Initial SoC and board support
- Enable EtherAVB
- Describe all SCIF devices
* Boards for R-Car Gen2 SoCs
- Enable watchdog support
* Wheat board for V2H (r8a7792) SoC
- Correct ADV7513 address usage
* tag 'renesas-dt-for-v4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (69 commits)
ARM: dts: r8a7740: Add CEU1
ARM: dts: r8a7740: Add CEU0
ARM: dts: r8a7745: Add PMU device node
ARM: dts: r8a7743: Add PMU device node
ARM: dts: r8a7794: Add PMU device node
ARM: dts: r8a7793: Add PMU device node
ARM: dts: r8a7792: Add PMU device node
ARM: dts: r8a7791: Add PMU device node
ARM: dts: r8a7790: Add PMU device nodes
ARM: dts: r7s72100: Add PMU device node
ARM: dts: r7s72100: Correct RTC interrupt types
ARM: dts: r7s72100: Correct watchdog timer interrupt type
ARM: dts: emev2: Add missing interrupt-affinity to PMU node
ARM: dts: sh73a0: Add missing interrupt-affinity to PMU node
ARM: dts: r8a73a4: Correct mask for GIC PPI interrupts
ARM: dts: r8a7790: Correct mask for GIC PPI interrupts
ARM: shmobile: r8a7794: alt: add EEPROM to DTS
ARM: dts: kzm9d: Drop unnecessary address properties from gpio_keys node
ARM: dts: silk: Drop unnecessary address properties from vin port node
ARM: dts: alt: Drop unnecessary address properties from vin port node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The register address should be the full address of the rng, not the
offset from the start of the SCU.
Fixes: 5daa8212c0 ("ARM: dts: aspeed: Describe random number device")
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
ENET "ipg" clock should be IMX7D_ENETx_IPG_ROOT_CLK
rather than IMX7D_ENET_AXI_ROOT_CLK which is for ENET bus
clock.
Based on Andy Duan's patch from the NXP kernel tree.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It should be "#cooling-cells" instead of "cooling-cells". Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- small DT improvements without functional changes
-----BEGIN PGP SIGNATURE-----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=xoAj
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
AT91 DT for 4.18:
- small DT improvements without functional changes
* tag 'at91-ab-4.18-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91-sama5d2_xplained: Use IRQ_TYPE specifier
ARM: dts: at91: sama5d4ek: use canonical compatible for touchscreen
Signed-off-by: Olof Johansson <olof@lixom.net>
New hardware support added:
USB controllers for AST2400 and AST2500 which have drivers
merged in 4.18.
Hardware random number generator which we made enhancements to many
releases ago, but never added the device tree parts.
Misc changes to support watchdog and gpio-keys features used by
OpenBMC systems.
New machines:
Intel S2600WF, an Intel platform family with an ASPEED AST2500 BMC.
Inventec Lanyang, a Power 9 platform with AST2500.
Portwell Neptune, a x86 server development kit with an AST2500.
-----BEGIN PGP SIGNATURE-----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=bGbT
-----END PGP SIGNATURE-----
Merge tag 'aspeed-4.18-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed into next/dt
ASPEED device tree updates for 4.18
New hardware support added:
USB controllers for AST2400 and AST2500 which have drivers
merged in 4.18.
Hardware random number generator which we made enhancements to many
releases ago, but never added the device tree parts.
Misc changes to support watchdog and gpio-keys features used by
OpenBMC systems.
New machines:
Intel S2600WF, an Intel platform family with an ASPEED AST2500 BMC.
Inventec Lanyang, a Power 9 platform with AST2500.
Portwell Neptune, a x86 server development kit with an AST2500.
* tag 'aspeed-4.18-devicetree' of git://git.kernel.org/pub/scm/linux/kernel/git/joel/aspeed:
ARM: dts: Aspeed: Enable USB ports on eval board.
ARM: dts: Add Aspeed SoC USB controllers to device-tree
ARM: dts: aspeed: Add S2600WF BMC Machine
ARM: dts: aspeed: Add Inventec Lanyang BMC
ARM: dts: aspeed: Add Portwell Neptune machine
ARM: dts: aspeed: witherspoon: Set alternate boot
ARM: dts: aspeed: witherspoon: Add gpio keys for power supply presence
ARM: dts: aspeed: witherspoon: Enable checkstop and cooling gpio keys
ARM: dts: aspeed: zaius: Add pcie-e2b-present gpio key
ARM: dts: aspeed: romulus: Add id-button gpio key
ARM: dts: aspeed: Describe random number device
Signed-off-by: Olof Johansson <olof@lixom.net>
Allwinner fixes for 4.17
Here is a bunch of fixes for merge issues, typos and wrong clocks being
described for simplefb, resulting in non-working displays.
* tag 'sunxi-fixes-for-4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: sun8i: v3s: fix spelling mistake: "disbaled" -> "disabled"
ARM: dts: sun4i: Fix incorrect clocks for displays
ARM: dts: sun8i: h3: Re-enable EMAC on Orange Pi One
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add support for audio over HDMI for Odroid X/X2/U3.
-----BEGIN PGP SIGNATURE-----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=Bzy3
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.18, part 2
1. Add support for audio over HDMI for Odroid X/X2/U3.
* tag 'samsung-dt-4.18-2' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Add support for audio over HDMI for Odroid X/X2/U3
Signed-off-by: Olof Johansson <olof@lixom.net>
-----BEGIN PGP SIGNATURE-----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=L7gS
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin into next/dt
berlin DT changes for v4.18
* tag 'berlin-dt-for-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/jszhang/linux-berlin:
ARM: dts: berlin2q: move PMU node from soc to root
ARM: dts: berlin*-dts: use SPDX-License-Identifier for berlin based board
ARM: dts: berlin*.dtsi: use SPDX-License-Identifier for berlin SoCs
ARM: dts: berlin2: fix irq type for arm twd timer
ARM: dts: berlin2q: fix irq type for arm twd timer
ARM: dts: berlin2q: add "cache-unified" to l2 node
ARM: dts: berlin2q: add interrupt-affinity to pmu node
ARM: dts: chromecast: use PWM for LEDs
ARM: dts: chromecast: override bad bootloader memory info
ARM: dts: berlin2cd: add Valve Steam Link board
ARM: dts: berlin2cd: add a label for the CPU node
ARM: dts: berlin2cd: add remaining nodes to apb subtrees
ARM: dts: berlin2cd: add remaining Cortex-A9 nodes
ARM: dts: berlin2cd: add ADC/thermal sensor node
ARM: dts: berlin2cd: move PMU node from soc to root
ARM: dts: berlin2cd: fix local timer interrupt flags
Signed-off-by: Olof Johansson <olof@lixom.net>
- remove MACH_MESON8B, only used for building DTs
-----BEGIN PGP SIGNATURE-----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=7Isa
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT changes for v4.18, round 2
- remove MACH_MESON8B, only used for building DTs
* tag 'amlogic-dt-2' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: meson: merge Kconfig symbol MACH_MESON8B into MACH_MESON8
ARM: dts: meson: build the Meson8b .dtbs with MACH_MESON8
Signed-off-by: Olof Johansson <olof@lixom.net>
The clocks for the 3 MMC controllers on pxa3xx platforms are CLK_MMC1,
CLK_MMC2 and CLK_MMC3. CLK_MMC is only for pxa2xx.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PXA3xx series features some extended GPIO banks which are named GPIO0_2,
GPIO1_2 etc. The PXA300, PXA310 and PXA320 have different numbers of such
pins, and they also have variant-specific register offsets.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
The PXA GPIO driver calls out to the pinctrl driver for claiming pins
unless the config has CONFIG_PINCTRL unset. IOW, if a pinctrl driver is
active, it must be visible to the GPIO driver.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
This series of changes contains fixes for already queued tps65218
IRQ_TYPE, and fixes for omap3 and am335x use of IRQ_TYPE. There are
also addition of oscillator clock for logicpd omap3 boards and a series
of changes to improve support for am3517-evm board. And there is also
a change to configure WLAN for am437x-sk-evm.
-----BEGIN PGP SIGNATURE-----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=rE26
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of dts changes for omap variants for v4.18 merge window
This series of changes contains fixes for already queued tps65218
IRQ_TYPE, and fixes for omap3 and am335x use of IRQ_TYPE. There are
also addition of oscillator clock for logicpd omap3 boards and a series
of changes to improve support for am3517-evm board. And there is also
a change to configure WLAN for am437x-sk-evm.
* tag 'omap-for-v4.18/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (24 commits)
ARM: dts: am3517-evm: Add User LEDs and Pushbutton
ARM: dts: am3517-evm: Add I/O expander for User DIP switches and LEDS
ARM: dts: logicpd-som-lv: Fix Touchscreen controller
ARM: dts: am3517-som: Add Seiko Instruments RTC s35390a
ARM: dts: am437x-sk-evm: add wilink8 support
ARM: dts: am3517-evm: Add LCD panel type 15 support
ARM: dts: am3517-som: Associate cpu to regulator supply
ARM: dts: am3517-som: Add TI TPS65023 regulators
ARM: dts: am3517-evm: Split off SOM features from baseboard
ARM: dts: am3517: Add pinmuxing, CD and WP for MMC1
ARM: dts: logicpd-som-lv: Add fixed 26MHz clock as fck for twl
ARM: dts: logicpd-torpedo: Add fixed 26MHz clock as fck for twl
ARM: dts: omap3-pandora-common: Use IRQ_TYPE specifier
ARM: dts: am335x-boneblue: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos.dtsi: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir5221: Use IRQ_TYPE specifier
ARM: dts: am335x-baltos-ir3220: Use IRQ_TYPE specifier
Revert "ARM: dts: am437x-sk-evm: Correct tps65218 irq type"
ARM: dts: am437x-epos-evm: Fixup (again) tps65218 irq type
ARM: dts: am437x-cm-t43: Fixup (again) tps65218 irq type
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is our usual bunch of changes for the H3 and H5 SoCs that share the
same SoC design but with different CPUs.
This time, most of the changes are about supporting CPUFreq on these SoCs,
with voltage scaling being enabled for a number of boards.
-----BEGIN PGP SIGNATURE-----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=trdL
-----END PGP SIGNATURE-----
Merge tag 'sunxi-h3-h5-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner H3/H5 support for 4.18
Here is our usual bunch of changes for the H3 and H5 SoCs that share the
same SoC design but with different CPUs.
This time, most of the changes are about supporting CPUFreq on these SoCs,
with voltage scaling being enabled for a number of boards.
* tag 'sunxi-h3-h5-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: h3: Add SY8106A regulator to Orange Pi PC
arm64: dts: allwinner: Add dts file for Libre Computer Board ALL-H3-CC H5 ver.
arm64: dts: allwinner: Sort dtb entries in Makefile
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
ARM: dts: sun8i: h2+: Add Libre Computer Board ALL-H3-CC H2+ ver.
ARM: dts: sun8i: h2-plus: Sort dtb entries in Makefile
arm: dts: sun8i: h3: libretech-all-h3-cc: Move board definition to common dtsi
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VCC-1V2 regulator voltage
ARM: dts: sun8i: h3: set the cpu-supply to VDD-CPUX on ALL-H3-CC H3 ver
ARM: dts: sun8i: h3: fix ALL-H3-CC H3 ver VDD-CPUX voltage
ARM: dts: sun8i: h3: add SY8113B regulator used by Orange Pi One board
ARM: dts: sun8i: h2+: add SY8113B regulator used by Orange Pi Zero board
ARM: dts: sun8i: h3: add operating-points-v2 table for CPU
ARM: dts: sunxi: h3/h5: Add r_i2c I2C controller
ARM: dts: sunxi: h3/h5: Add r_i2c pinmux node
Signed-off-by: Olof Johansson <olof@lixom.net>
Here is our usual bunch of DT changes for our arm SoCs, with most
significantly:
- MIPI-DSI support for the A33
- NAND support for the A33
- SMP support for the A83t
- GMAC support for the R40
- And some new boards: Olimex A20-SOM-EVB-eMMC, Nintendo NES and SuperNES
Classic
-----BEGIN PGP SIGNATURE-----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=f5iC
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Allwinner DT additions for 4.18
Here is our usual bunch of DT changes for our arm SoCs, with most
significantly:
- MIPI-DSI support for the A33
- NAND support for the A33
- SMP support for the A83t
- GMAC support for the R40
- And some new boards: Olimex A20-SOM-EVB-eMMC, Nintendo NES and SuperNES
Classic
* tag 'sunxi-dt-for-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun7i: Add Olimex A20-SOM-EVB-eMMC board
ARM: dts: sun8i: r40: bananapi-m2-ultra: Enable GMAC ethernet controller
ARM: dts: sun8i: r40: Add device node and RGMII pinmux node for GMAC
ARM: dts: sun8i: r40: bananapi-m2-ultra: Sort device node dereferences
ARM: dts: sun8i: Add enable-method for SMP support for the A83T SoC
ARM: dts: sun8i: a83t: Add CCI-400 node
ARM: dts: sun8i: Add R_CPUCFG device node for the A83T dtsi
ARM: dts: sun8i: Add CPUCFG device node for A83T dtsi
ARM: dts: nes: add Nintendo NES/SuperNES Classic Edition support
ARM: dts: sun8i: a23/a33: declare NAND pins
ARM: dts: sunxi: Add sid for a83t
ARM: dts: sun8i: a33: Add the DSI-related nodes
ARM: dts: sunxi: Change sun7i-a20-olimex-som204-evb to not use cd-inverted
ARM: sun8i: v40: enable USB host ports for Banana Pi M2 Berry
Signed-off-by: Olof Johansson <olof@lixom.net>
- New boards support: BTicino i.MX6DL Mamoj board, DHCOM iMX6 SoM and
PDK2 board, Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit,
Kieback & Peter GmbH iMX6Q TPC board.
- A series from Anson Huang to add a bunch of devices for i.MX6SX
SabreAuto board, PMIC, IO expanders, FEC, Watchdog, LED and Touch.
- Update i.MX7D for cpufreq support, using operating-points-v2
bindings, correcting cpu supply name for voltage scaling.
- Clean up unneeded 'codec-handle' property from imx25-pdk and
imx53-tx53 device tree.
- Switch SoC dtsi and NXP board dts files to use SPDX identifier.
- Remove unnecessary '#address-cells/#size-cells' to fix DTC warning
avoid_unnecessary_addr_size seen with W=1 switch.
- A series from Rob Herring to fix DTC warning graph_endpoint seen with
IPU OF graph when W=1 switch is on.
- Update a few boards to use symbol name instead of hard-coding the
input codes.
- Update a number of boards to use IRQ_TYPE specifier instead of the
raw value.
- A few updates for i.MX6 RDU2 board: bumping SoC/PU operating points,
adding assigned clocks for GPU, and enabling eGalax touchscreen.
- A couple of i.MX51 RDU1 updates: limiting usbh1 to full-speed, and
cleaning up eMMC device node.
- Convert Hummingboard audio bindings from imx-audio-sgtl5000 to
simple-audio-card, so that auxiliary audio devices such as external
amplifiers can be supported.
- Replace underscore with hyphen in aliases name to fix DTC warning
alias_paths with W=1 switch.
- A couple of updates on i.MX7D SAI and i.MX6ULL UART5 pin defines.
- Other random and small changes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJbAYgeAAoJEFBXWFqHsHzO8ZUH/RG21GCtMGozrIoL9f0/6R4T
wBj/vdg31XGk7XYkmxKH5J6hwryco7Z2uMfKhsRbfXUzt+DxwtseJUgaKHygk/oh
ns7LhuSvhYwqa6AENN70DOt4b3TX/sAyYrBIFUXQRsZrafPhn7+8/Y8oiLbY3lOs
cctrHA31jz5ytXVoLT1AkFST020JcRjaTpRFYqDohpcOOMqhpjPxPJ6uF6lE/LHf
XVzBYGbxzmzH5PDpEy7KjzkxDt0cvBfH7LrfvcHzi8hGho3P1ShpRah/TYKpmwkx
MVD1NRFTCwKgIjibcjfLse9NJdixza5j6pvWaCacC9agWG6drOxYvYy4ILe2ros=
=F8Nx
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree update for 4.18:
- New boards support: BTicino i.MX6DL Mamoj board, DHCOM iMX6 SoM and
PDK2 board, Engicam i.CoreM6 1.5 Quad/Dual MIPI starter kit,
Kieback & Peter GmbH iMX6Q TPC board.
- A series from Anson Huang to add a bunch of devices for i.MX6SX
SabreAuto board, PMIC, IO expanders, FEC, Watchdog, LED and Touch.
- Update i.MX7D for cpufreq support, using operating-points-v2
bindings, correcting cpu supply name for voltage scaling.
- Clean up unneeded 'codec-handle' property from imx25-pdk and
imx53-tx53 device tree.
- Switch SoC dtsi and NXP board dts files to use SPDX identifier.
- Remove unnecessary '#address-cells/#size-cells' to fix DTC warning
avoid_unnecessary_addr_size seen with W=1 switch.
- A series from Rob Herring to fix DTC warning graph_endpoint seen with
IPU OF graph when W=1 switch is on.
- Update a few boards to use symbol name instead of hard-coding the
input codes.
- Update a number of boards to use IRQ_TYPE specifier instead of the
raw value.
- A few updates for i.MX6 RDU2 board: bumping SoC/PU operating points,
adding assigned clocks for GPU, and enabling eGalax touchscreen.
- A couple of i.MX51 RDU1 updates: limiting usbh1 to full-speed, and
cleaning up eMMC device node.
- Convert Hummingboard audio bindings from imx-audio-sgtl5000 to
simple-audio-card, so that auxiliary audio devices such as external
amplifiers can be supported.
- Replace underscore with hyphen in aliases name to fix DTC warning
alias_paths with W=1 switch.
- A couple of updates on i.MX7D SAI and i.MX6ULL UART5 pin defines.
- Other random and small changes.
* tag 'imx-dt-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (72 commits)
ARM: dts: imx28/imx53: enable edt-ft5x06 wakeup source
ARM: dts: imx51-zii-rdu1: cleanup eMMC node
ARM: dts: vf610-zii-dev: enable vf610 builtin temp sensor
ARM: dts: imx7d: use operating-points-v2 for cpu
ARM: dts: imx7s-warp: remove unnecessary cpu regulator supply
ARM: dts: imx7d: correct cpu supply name for voltage scaling
ARM: dts: imx51-zii-rdu1: limit usbh1 to full-speed
ARM: dts: imx6/7: Remove unit-address from anatop regulators
ARM: dts: imx: Switch NXP boards to SPDX identifier
ARM: dts: imx6qdl-phytec-pfla02: Use IRQ_TYPE specifier
ARM: dts: imx53-voipac-dmm-668: Use IRQ_TYPE specifier
ARM: dts: imx53-qsb: Use IRQ_TYPE specifier
ARM: dts: vf-colibri-eval-v3: Use IRQ_TYPE specifier
ARM: dts: imx6q-gk802: Do not hardcode input codes
ARM: dts: imx53-smd: Do not hardcode input codes
ARM: dts: imx53-ard: Do not hardcode input codes
ARM: dts: imx7: Fix error in coresight TPIU graph connection
ARM: dts: imx53: Fix LDB OF graph warning
ARM: dts: imx: fix IPU OF graph endpoint node names
ARM: dts: imx: Switch to SPDX identifier
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Add the common data for all dk07 based boards.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the common parts for the dk04 boards.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The max opp frequency is 716MHZ. So update that.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Now with the driver updates for some peripherals being there,
add i2c, spi, pcie, bam, qpic-nand, scm nodes to enhance the available
peripheral support.
Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add a 'chosen' node to select the serial console.
This is needed when bootloaders do not pass the
'console=' bootargs.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
- Update 32-bit Marvell EBU NAND DT nodes with new bindings
- Add NAND pinctrl information for the Armada 98DX3236 and variants
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWv8BugAKCRALBhiOFHI7
1SbsAKCA4bLq2Z82OGwmb72UMRjEJRHerQCgrTrBKe4r2Q+NAt27RG1X4LsbqoU=
=boOe
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.18-1' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.18 (part 1)
- Update 32-bit Marvell EBU NAND DT nodes with new bindings
- Add NAND pinctrl information for the Armada 98DX3236 and variants
* tag 'mvebu-dt-4.18-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-xp-98dx: Add NAND pinctrl information
ARM: dts: armada-39x: update NAND node with new bindings
ARM: dts: armada-38x: update NAND node with new bindings
ARM: dts: armada-375: update NAND node with new bindings
ARM: dts: armada-370-xp: update NAND node with new bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
Contains a fix for the high-speed UART on Toradex Apalis TK1 boards as
well as IOMMU enablement for various devices on Tegra30 and Tegra30.
-----BEGIN PGP SIGNATURE-----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=I1bn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.18-rc1
Contains a fix for the high-speed UART on Toradex Apalis TK1 boards as
well as IOMMU enablement for various devices on Tegra30 and Tegra30.
* tag 'tegra-for-4.18-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra114: Add IOMMU nodes to Host1x and its clients
ARM: dts: tegra30: Add IOMMU nodes to Host1x and its clients
ARM: tegra: apalis-tk1: Fix high speed UART compatible
Signed-off-by: Olof Johansson <olof@lixom.net>
* DA850 EVM gains USB support, SD card write-protect, card detect
and some clean-up
* Support for gpio-ranges makes using gpios from DT much easier
* Lego EV3 clean-up
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XbDP
-----END PGP SIGNATURE-----
Merge tag 'davinci-for-v4.18/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into next/dt
DaVinci device-tree updates for v4.18
* DA850 EVM gains USB support, SD card write-protect, card detect
and some clean-up
* Support for gpio-ranges makes using gpios from DT much easier
* Lego EV3 clean-up
* tag 'davinci-for-v4.18/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: dts: da850-evm: add WP and CD to MMC
ARM: dts: da850-lego-ev3: remove unnecessary gpio-keys properties
ARM: dts: da850-evm: use phandles to extend nodes
ARM: dts: da850: use gpio-ranges
ARM: dts: da850-evm: Enable usb_phy, usb0 and usb1
Signed-off-by: Olof Johansson <olof@lixom.net>
- add support for meson8m2 SoC
- new board: Tronsmart MXIII Plus using meson8m2 SoC
- odroid-c1: add IR
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEe4dGDhaSf6n1v/EMWTcYmtP7xmUFAlr7W3AACgkQWTcYmtP7
xmULJQ/+NEVPnD63xPOtn0SEtILequTG0nJxDYQX2XUWXCnevq0+emRKRPvCr153
ZKTIaOiR4u5LO7JjgYX+X/lwvkdkOF64oqjfKQSIOmsHy0d3F7/e4jeySc2pncZ7
Xl19SyKa3tcbjmkoXUikEtnXV20hi8e3ADN1pALa6/4L+eSCLsTcThLN+H6brjCj
Pk6hn1GbgovbGKRthrOFKOwk9JMnrVSXsPsPV/f4AiIJHYqvXIxHV4YyGOvboH9a
WrZpIRtqHuk5zu44QyeaX5lYpWv3nOmFnTLvVgFc5HGxkoTIQM60PuoIKsSXGXkn
1HZRWENt44m8QtnFhNK57+hyvGMf+eSbeXFp5I1n+hWgk1p9R1woWc3eghpWuUkJ
J8maAe5MRBZG4fAHdoTymX048g5vkcA/kDYj9To/sQeOY+18PepuYcNp6i3yQU5Z
BL+uxJx7BX5ztvYwiD07SjeXMDaMb4LxxnnJUEDUUkKvq9W6DsTgdyyBxa2evRBi
ADaxb/t6+DAA14JWo01VF2umFlidjEL2xTFEcI6itnUHtU+tyAHck1KNFRYNG17h
Z2d3iKPYr+16rLiqlLembYK0nZf9ZnQszzAavM2TF7e2pT/b6NneIIgEjENaGV9E
7CuR5ppTAri6DbowCHpM38velxYc4FIGVe8Wei0vSmHeqk5AYu8=
=+PvJ
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Amlogic 32-bit DT updates for v4.18
- add support for meson8m2 SoC
- new board: Tronsmart MXIII Plus using meson8m2 SoC
- odroid-c1: add IR
* tag 'amlogic-dt' of https://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM: dts: meson8m2: add support for the Tronsmart MXIII Plus
ARM: dts: meson8: add the uart_A pins
ARM: dts: meson: add support for the Meson8m2 SoC
ARM: meson: add support for the Meson8m2 SoCs
ARM: dts: meson8b: odroid-c1: enable the IR receiver
ARM: dts: meson8b: odroid-c1: sort nodes alphabetically
ARM: dts: meson8b: add the cortex-a5-pmu compatible PMU
ARM: dts: meson8: add the cortex-a9-pmu compatible PMU
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds a DTS file for Sony Xperia Z1 Compact with support for
regulators, serial UART, eMMC/SD-card, USB, charger, backlight,
coincell and buttons.
Work based on arch/arm/boot/dts/qcom-msm8974-sony-xperia-honami.dts.
Signed-off-by: Attila Szöllősi <ata2001@airmail.cc>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This enables both USB ports as host with EHCI and UHCI
attached to them.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This adds the USB controllers to the DT template of the
AST24xx and AST25xx SoCs.
This patch doesn't enable them by default on any board specific
.dts yet. This will be done when we have the necessary clock/reset
and pinmux support. In the meantime though, this will work if
u-boot configures things properly.
For the AST2400 I only added pinmux definition for port 1
which is dual USB1/USB2. There are additional USB1 only ports
that might require more work but I don't have HW to test at
hand so I'm leaving that to whoever cares.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
S2600WF is a Intel platform family with an ASPEED AST2500 BMC.
Signed-off-by: James Feist <james.feist@linux.intel.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
The Inventec Lanyang is Power 9 platform with ast2500 BMC.
Signed-off-by: Brian Yang <yang.brianc.w@inventec.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Initial introduction of Portwell Neptune family equipped with
Aspeed 2500 BMC SoC. Neptune is a x86 server development kit with a
ASPEED ast2500 BMC manufactured by Portwell. Specifically, This
adds the neptune platform device tree file including the flash
layout used by the neptune machines.
Signed-off-by: Amithash Prasad <amithash@fb.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set watchdog 2 to boot from the alternate flash chip when the watchdog
timer expires and the system is reset. This enables "brick protection."
Signed-off-by: Eddie James <eajames@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Enable gpio-keys events for the checkstop and water/air cooled
gpios for use by applications on the Witherspoon system.
Signed-off-by: Brad Bishop <bradleyb@fuzziesquirrel.com>
Acked-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add GPIO key to check presence of PCIE E2B.
Signed-off-by: Lei YU <mine260309@gmail.com>
Acked-by: Xo Wang <xow@google.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
This patch adds support of external interrupt for
gpio[a..k], gpioz
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
This patch adds external interrupt (exti) support
on stm32mp157c SoC.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Follow the recent trend for the license description, and also fix the
wrongly stated X11 to MIT.
As already pointed on the DT ML, the X11 license text [1] is explicitly
for the X Consortium and has a couple of extra clauses. The MIT
license text [2] is actually what the current DT files claim.
[1] https://spdx.org/licenses/X11.html
[2] https://spdx.org/licenses/MIT.html
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
fix below warning about PPI interrupts configuration:
"GIC: PPI13 is secure or misconfigured"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
fix below warning about PPI interrupts configuration:
"GIC: PPI13 is secure or misconfigured"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Without this property, we get this boot warning:
"L2C: device tree omits to specify unified cache"
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Control the Chromecast's two LEDs using PWM instead of GPIO pins. This
allows for variable brightness.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
On the Chromecast, the bootloader provides us with an ATAG_MEM of
start=0x01000000 and size=0x3eff8000. This is clearly incorrect, as the
range given encompasses nearly a GiB but the Chromecast only has 512MiB
of RAM! Additionally, this causes the kernel to be decompressed at
0x00008000, below the claimed beginning of RAM, and so the boot fails.
Since the existing ATAG parsing code runs before the kernel is even
decompressed and irrevocably patches the device tree, don't even try
to bypass it. Instead, use the "linux,usable-memory" property instead
of the "reg" property to define the real range. The ATAG code only
overwrites reg, but linux,usable-memory is checked first in the OF
driver, so the fact that reg gets changed makes no difference.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Valve Steam Link is a consumer device built around the Marvell BG2CD SoC.
This board file enables the UART, USB and Ethernet interfaces as well as
internal I2C and SDIO, and adds SoC voltage regulator and board-specific
GPIO restart method info.
Cc: Sam Lantinga <saml@valvesoftware.com>
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This is useful if the board file needs to reference it.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This adds most of the remaining Designware IP cores under APB trees in
the interest of documenting assignment of interrupts and memory ranges.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
This adds DT nodes for the Cortex-A9 MPCore SCU, local watchdog and
most importantly the global timer.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cortex-A9 PMU has no associated memory ranges and "make dtbs W=1" warns
about missing reg or ranges property. To avoid the warning, move the PMU
node out of soc subtree to the root.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Use the correct trigger type for Cortex-A9. This was fixed for several
other SoCs since the kernel started issuing a boot-time warning.
Signed-off-by: Alexander Monakov <amonakov@ispras.ru>
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Fix the DT node addresses to match the reg property addresses,
which were verified to match the TRM:
http://www.ti.com/lit/pdf/sprui30
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently there are two identical Kconfig options where only differences
are the Kconfig help text and the list of .dtbs that are built:
- MACH_MESON8
- MACH_MESON8B
Build the Meson8b .dtbs when MACH_MESON8 is selected to get rid of the
latter Kconfig symbol later.
Suggested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
With the new rev.E of A20-SOM-EVB, there is option for 16GB eMMC.
Currently used card is KLMAG2GEND, wired to MMC2 slot.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The touchscreen driver no longer configures the device as wakeup source by
default. A "wakeup-source" property is needed.
To avoid regressions, this patch changes the DTS files for the only two
users of this driver that didn't have this property yet.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On RDU1, sdhc1 is used for eMMC, and that is 3.3V only.
Thus configure device node not to probe it as SD/SDIO and not try 1.8V.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Vybrid has single internal temperature sensor connected to both internal
ADC modules.
vf610-zii-dev already has ADC0 enabled. Now, to get temperature sensor
captured by iio_hwmon driver, need to configure iio_hwmon node to use
that ADC.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This patch uses "operating-points-v2" instead of
"operating-points" to be more fit with cpufreq-dt
driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX7S does NOT support CPU frequency scaling, so no
need to specify the CPU regulator supply.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Correct CPU supply name to meet cpufreq-dt driver's
requirement for voltage scaling.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On RDU1, imx51 usbh1 interface is either not used, or used via external
block that breaks USB2 signalling.
To keep things working if high-speed device gets connected to that
block, use ChipIdea feature to limit port to full speed.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unit-address and reg property from anatop regulators to fix
the following DTC warnings with W=1:
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddcore@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
arch/arm/boot/dts/imx6dl-apf6dev.dtb: Warning (unique_unit_address): /soc/aips-bus@2000000/anatop@20c8000/regulator-vddpu@20c8140: duplicate unit-address (also used in node /soc/aips-bus@2000000/anatop@20c8000/regulator-vddsoc@20c8140)
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are some LED's attached to the GPIO expander, and
there are is a bank of switches attached to the GPIO expander.
This patch associates the LED and the switches to it.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is a tca6416 GPIO expander on i2c2. This patch enables the
GPIO expander which has several LED's and some connected DIP
switches
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin control information for the NAND interface on the Armada
98DX3236 and variants.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Use the new bindings of the Marvell NAND controller driver. Also adapt
the NAND controller node organization to distinguish which property is
relevant for the controller, and which one is NAND chip specific. Expose
the partitions as a subnode of the NAND chip.
Remove the 'marvell,nand-enable-arbiter' property, not needed anymore
as the new driver activates the arbiter by default for all boards which
is either needed or harmless.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
The Bananapi M2 Ultra has a Realtek RTL8211E RGMII PHY tied to the GMAC.
The PMIC's DC1SW output provides power for the PHY, while the ALDO2
output provides I/O voltages on both sides.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The R40 SoC has a GMAC (gigabit capable Ethernet controller). Add a
device node for it. The only publicly available board for this SoC
uses an RGMII PHY. Add a pinmux node for it as well.
Since this SoC also has an old 10/100 Mbps EMAC, which also has an
MDIO bus controller, the MDIO bus for the GMAC is labeled "gmac_mdio".
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The device nodes dereference (&foo) usages should be sorted by the label
names, barring any parsing order issues such as the #include statement
for the PMIC's .dtsi file that must come after the PMIC.
Move the mmc and ohci blocks in front of the PMIC's regulator blocks.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
The legacy mode uses the write protect and card detect but DT does not.
This patch enables Write-Protect and Card-Detect pins for the MMC card, and
the gpio-ranges property sets the gpio pinmuxing for those respective pins.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlr5ccMQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgYd7B/4guy/cJFRSzZfhAl3XYeLlt7F4/RPJOUUk
Wj4PNDMP8hKnAj/2xcyypmf4Of/IvH5PwqywA4mgL7fzE2LkrQkRwpiHzRn1BnJA
2NoNVCRGRDYmMJFqelYs3bPfrGd/kYYaOjeNaD3mQa8cCAv+nZt3YS7ExiSrQeup
Yeg+V5wa0fqtcZneArgsBBD06Fatn2EksYsBtyTwTdf0AYJ+vT+DHEOubVXl4RNm
4eFm7fbplXmjBVnmTDINuRLusmqcDAu3tl/Q+hMqjJefdioyH6zdVPn38GqfhUBO
drg7tLbMQCdYNNCSrrJ5mzoVw4Zp8majfFRlbF69cpabhc6deHYS
=oFJx
-----END PGP SIGNATURE-----
Merge tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Fixed pin numbers for uart4 on rk3288, iommu clocks and small changes
over multiple boards like default serial setting for rk3288-tinker,
output selection for the dp83867 on the phycore-som and the newly
added pwm-backlight delay properties for veyron boards.
* tag 'v4.18-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: default serial for rk3288 Tinker Board
ARM: dts: rockchip: set PWM delay backlight settings for Minnie
ARM: dts: rockchip: set PWM delay backlight settings for Veyron
ARM: dts: rockchip: add clocks in iommu nodes
ARM: dts: rockchip: Add dp83867 CLK_OUT muxing on rk3288-phycore-som
ARM: dts: rockchip: fix uart4 pin-numbers for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
2. Use of standard GPIO controller bindings for few sysreg components
like LED, MMC Write Protect/Card Detect and Flash Write Protect
to fix some of the new DTC warnings
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=X3Vc
-----END PGP SIGNATURE-----
Merge tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/dt
ARMv7 Vexpress updates/cleanups for v4.18
1. Syntactic restructuring of motherboard include file so that it can be
included at the top of any other DTS file as it should be rather than
existing include in the middle of the file at a specific location
2. Use of standard GPIO controller bindings for few sysreg components
like LED, MMC Write Protect/Card Detect and Flash Write Protect
to fix some of the new DTC warnings
3. Cleanup to replace all underscores('_') with hyphens('-') in the
device node names
* tag 'vexpress-updates-4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
ARM: dts: vexpress: replace '_' with '-' in node names
ARM: dts: vexpress: use standard gpio bindings for sys_{led,mci,flash}
ARM: dts: vexpress: Restructure motherboard includes
Signed-off-by: Olof Johansson <olof@lixom.net>
The touchscreen patch did not apply to this branch correctly and
inadvertently got placed onto I2C2 when it should be on I2C3. This fixes
the issue.
Fixes: 121685b146 ("ARM: dts: logicpd-som-lv: Enable Touchscreen
controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The SOM used in the am3517-evm has a s35390a onboard. This
patch allows the s35390a to be used as the RTC.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
enable mmc3 used for wlan and uart1 used for bluetooth
configure the gpios used for wlan and bluetooth controls
add fixed voltage regulator used for wlan power control
Signed-off-by: Eyal Reizer <eyalr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM3517-EVM by Logic PD has a Logic PD type 15 display LCD
attached to the baseboard, and the SOM itself has an integrated
touchscreen controller. This patch enables both the LCD and
the tsc2004 on the SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am3517-som is powered by vdd_core_reg, so let's add the
'cpu' device-tree node with the 'vdd_core' regulator as the core
supply.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit adds the common voltage regulators used on LogicPD's
AM3517 System-On-Modules.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The am3517-evm consists of an am3517 SOM-M2 and a baseboard.
As items are added that are unique to the baseboard, let's place
them in a file called am3517-som.dtsi. These items will be
common for all variants of the SOM.
Anything unique to the baseboard will be placed into
am3517-evm.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The boardboard supports card detect and write protect, so let's
enable those pins.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK. This way we will
not depend on the bootloader to configure the CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The board uses 26MHz oscillator for the twl4030 HFCLK.
This way we will not depend on the bootloader to configure the
CFG_BOOT:HFCLK_FREQ
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This reverts commit 561f9bcf26.
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 561f9bcf26 ("ARM: dts: am437x-sk-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 7a53a34622 ("ARM: dts: am437x-epos-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: b997f534b5 ("ARM: dts: am437x-cm-t43: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
While the correct IRQ level fixed the WARN_ON(), but prevented the probe
of tps65218 as GIC_SPI does not support LEVEL_LOW (?)
Use LEVEL_HIGH as it looks to be the accurate one since the INTn of TPS is
connected to NMIn of the SoC.
Fixes: 5692b911c9 ("ARM: dts: am437x-gp-evm: Correct tps65218 irq type")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the backlight phandle the driver can manage the backlight on/off in
sync with the panel enable/disable.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 CM-T3x based boards define 2 /connector nodes for S-Video and
DVI output. However, since they have the same node name, the S-Video
connector overwritten. This leaves a dangling graph connection which
gives the following warning:
arch/arm/boot/dts/omap3-sbc-t3517.dtb: Warning (graph_endpoint):
/ocp@68000000/dss@48050000/encoder@48050c00/port/endpoint: graph
connection to node '/connector/port/endpoint' is not bidirectional
Fix this by renaming the nodes to s-video-connector and dvi-connector.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap3-devkit8000-common.dtsi defines a graph connection for DVI, but
then omap3-devkit8000-lcd-common.dtsi overrides that with a graph
connection for the LCD as the same output signals are used. This
leaves an incomplete graph as the TFP410 output has only half a
connection. The result is the following warning:
arch/arm/boot/dts/omap3-devkit8000-lcd70.dtb: Warning (graph_endpoint):
/encoder0/ports/port@0/endpoint: graph connection to node
'/ocp@68000000/dss@48050000/port/endpoint' is not bidirectional
Fix this by defining multiple endpoints which is the correct way to show
a 1 to many connection.
Cc: "Benoît Cousson" <bcousson@baylibre.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch switches Odroid X/X2/U3 to use dedicated Odroid audio subsystem
DT bindings instead of the simple-card in order to add support for audio
over HDMI.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Replace magic number with the proper IRQ_TYPE specifier to improve DT
readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1. Add support for USB OTG port on Origen board.
2. Allow earlycon on Rinato board.
3. Cleanup from obsolete properties.
4. Fix DTC warnings.
5. Remove Exynos5440 entirely.
6. Add mem-2-mem Scaler devices.
-----BEGIN PGP SIGNATURE-----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=1XLN
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DTS ARM changes for v4.18
1. Add support for USB OTG port on Origen board.
2. Allow earlycon on Rinato board.
3. Cleanup from obsolete properties.
4. Fix DTC warnings.
5. Remove Exynos5440 entirely.
6. Add mem-2-mem Scaler devices.
* tag 'samsung-dt-4.18' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Update x and y properties for mms114 touchscreen
ARM: dts: exynos: Add mem-2-mem Scaler devices
ARM: dts: s3c64xx: Remove skeleton.dtsi and fix DTC warnings for /memory
ARM: dts: s3c24xx: Fix unnecessary address/size cells DTC warnings
ARM: dts: s3c24xx: Remove skeleton.dtsi and fix DTC warning for /memory
ARM: dts: exynos/s3c: Remove leading 0x and 0s from bindings notation
ARM: dts: exynos: Remove Exynos5440
ARM: dts: exynos: Remove unnecessary address/size properties in dp-controller of Exynos5
ARM: dts: exynos: Bring order in fixed-regulators naming in Midas boards
ARM: dts: exynos: Remove regulators node container in Origen and N710x
ARM: dts: exynos: Remove unnecessary address/size properties in Origen
ARM: dts: exynos: Remove unnecessary address/size properties in Midas boards
ARM: dts: exynos: Fix invalid node referenced by i2c20 alias in Peach Pit and Pi
ARM: dts: exynos: Move syscon poweroff and restart nodes under the PMU
ARM: dts: exynos: Remove obsolete clock properties from power domains
ARM: dts: exynos: Add serial path for Rinato board to get earlycon support
ARM: dts: exynos: Add support for USB OTG port on Origen board
Signed-off-by: Olof Johansson <olof@lixom.net>
- Set righ flashes on DNS-313
- Activate ATA1 on NAS4220B
- Set right harddisk triggers on the D-Link devices
- Fix all DTC warnings
-----BEGIN PGP SIGNATURE-----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=pLJv
-----END PGP SIGNATURE-----
Merge tag 'gemini-dts-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik into next/dt
DTS updates for the Gemini:
- Set righ flashes on DNS-313
- Activate ATA1 on NAS4220B
- Set right harddisk triggers on the D-Link devices
- Fix all DTC warnings
* tag 'gemini-dts-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: dts: Fix DTC warnings
ARM: dts: Add second ATA to NAS4220B
ARM: dts: Fix bootargs for Gemini D-Link devices
ARM: dts: Fix the DNS-313 flash compatible
ARM: dts: Set DNS-685 LEDs to use better triggers
ARM: dtd: Set DNS-313 LEDs to use better triggers
ARM: dts: gemini: Fix "debounce-interval" property misspelling
Signed-off-by: Olof Johansson <olof@lixom.net>
for 4.18, please pull the following:
- Stefan provides updates to the BCM2835 RNG Device Tree binding and
Device Tree node by adding its missing interrupt line.
- Rafal switches the Luxul XWC-1000 and the D-Link DIR-885L to the new
partitions syntax which allows specifying a partition parser
- Rafal also updates a bunch of BCM5301X Device Tree source files to a
more standard SPDX tag and dual GPL 2.0 and MIT. This is a follow-up
to this discussion with Greg:
https://lkml.org/lkml/2018/4/28/179
- Dan adds support for two Luxul devices: XAP-1610 (based on BCM47094)
and XWR-3150 V1 (similar to XWR-3100)
- Stefan provides a set of updates to the BCM283x Device Tree sources to
support the Raspberry Pi 3 B+ for both the ARM and ARM64 kernels. He
adds the required nodes for the LAN7515 USB Ethernet, Cypress CYW43455
BT/WiFi combo chip. Stefan also provides a few fixes for the PWM pin
assignment for RPi 3B and Zero/Zero W. Finally, Stefan adds the
missing GPIOs for controlling additional peripherals now that support
for the RPi 3 GPIO expander has landed
-----BEGIN PGP SIGNATURE-----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=R36h
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.18/devicetree' of https://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoC Device Tree changes
for 4.18, please pull the following:
- Stefan provides updates to the BCM2835 RNG Device Tree binding and
Device Tree node by adding its missing interrupt line.
- Rafal switches the Luxul XWC-1000 and the D-Link DIR-885L to the new
partitions syntax which allows specifying a partition parser
- Rafal also updates a bunch of BCM5301X Device Tree source files to a
more standard SPDX tag and dual GPL 2.0 and MIT. This is a follow-up
to this discussion with Greg:
https://lkml.org/lkml/2018/4/28/179
- Dan adds support for two Luxul devices: XAP-1610 (based on BCM47094)
and XWR-3150 V1 (similar to XWR-3100)
- Stefan provides a set of updates to the BCM283x Device Tree sources to
support the Raspberry Pi 3 B+ for both the ARM and ARM64 kernels. He
adds the required nodes for the LAN7515 USB Ethernet, Cypress CYW43455
BT/WiFi combo chip. Stefan also provides a few fixes for the PWM pin
assignment for RPi 3B and Zero/Zero W. Finally, Stefan adds the
missing GPIOs for controlling additional peripherals now that support
for the RPi 3 GPIO expander has landed
* tag 'arm-soc/for-4.18/devicetree' of https://github.com/Broadcom/stblinux:
ARM: dts: BCM5301X: Switch D-Link DIR-885L to the new partitions syntax
ARM: dts: BCM5301X: Relicense Asus RT-AC87U file to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Add DT for Luxul XAP-1610
ARM: dts: BCM5301X: Add DT for Luxul XWR-3150 V1
ARM: dts: BCM5301X: Relicense Buffalo files to the GPL 2.0+ / MIT
ARM: dts: BCM5301X: Relicense most DTS files to the GPL 2.0+ / MIT
arm64: dts: broadcom: Add reference to Raspberry Pi 3 B+
ARM: dts: bcm2837: Add Raspberry Pi 3 B+
dt-bindings: bcm: Add Raspberry Pi 3 B+
ARM: dts: bcm2837: Add missing GPIOs of Expander
ARM: dts: bcm283x: Fix PWM pin assignment
ARM: dts: BCM5301X: Switch Luxul XWC-1000 to the new fixed partitions syntax
ARM: bcm283x: Add missing interrupt for RNG block
dt-binding: rng: Add interrupt property for BCM2835
Signed-off-by: Olof Johansson <olof@lixom.net>
For PCI, the second and third cell in ranges specifies the upper and
lower target address for address translation. This target address will
be used to program the internal address translation unit (iATU).
The current device tree configuration will program the iATU to translate
CPU accesses to 0x08000000 to PCI address 0x0 (with TLP type MEM).
The device tree configuration also specifies that CPU acesses to
0x0fe00000 will be translated to PCI address 0x0 (with TLP type I/O).
We cannot have both I/O space and memory space at PCI address 0x0.
The PCI code already uses the CPU address when assigning addresses to
memory BARs, so for memory space the PCI address should be the same as
the CPU address. This also matches how all other device trees using
snps,dw-pcie are configured.
The existing configuration appears to work, even if it is incorrect.
For some reason the iATU doesn't obey the existing configuration,
and doesn't translate CPU accesses from 0x08000000 to PCI address 0x0.
The reason why the existing configuration works at all is probably
because the default behavior, when there is no match, is to use the
untranslated address. This happens to work for memory space, since
it's a 1:1 mapping. However, instead of relying on this behavior,
let's configure the iATU correctly.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Remove the usage of IRQ_TYPE_NONE to fix loud warnings from
patch (83a86fbb5b "irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE").
Signed-off-by: Thierry Escande <thierry.escande@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The right string is msm8660 and there is also apq8060, but not
apq8660, so fix this.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The QSEE (trustzone) is started on IPQ4019 before Linux is started.
According to QCA, it is placed in in the the memory region
0x87e80000-0x88000000 and must not be accessed directly. There is an
additional memory region 0x87e00000-0x87E80000 smem which which can be used
for communication with the TZ. The driver for the latter is not yet ready
but it is still not allowed to use this memory region like any other
memory region.
Not reserving this memory region either leads to kernel crashes, kernel
hangs (often during the boot) or bus errors for userspace programs. The
latter happens when a program is using a memory region which is mapped to
these physical memory regions.
[ 571.758058] Unhandled fault: imprecise external abort (0xc06) at 0x01715ff8
[ 571.758099] pgd = cebec000
[ 571.763826] [01715ff8] *pgd=8e7fa835, *pte=87e7f75f, *ppte=87e7fc7f
Bus error
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
vbat_sns is needed to estimate a fairly accurate on chip voltage
and bat_therm is needed to produce an accurate percentage
from the estimated ocv.
Signed-off-by: Craig Tatlor <ctatlor97@gmail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch marks all the gsbi i2c node at soc level dtsi, so that kernel
would not assume that its enabled and result in pin conflicts when gsbi
is used for UART or SPI.
Without this patch we see below pin conflict.
apq8064-pinctrl 800000.pinctrl: pin GPIO_20 already requested by
12450000.serial; cannot claim for 12460000.i2c
apq8064-pinctrl 800000.pinctrl: pin-20 (12460000.i2c) status -22
apq8064-pinctrl 800000.pinctrl: could not request pin 20 (GPIO_20)
from group gpio20 on device 800000.pinctrl
i2c_qup 12460000.i2c: Error applying setting, reverse things back
i2c_qup: probe of 12460000.i2c failed with error -22
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This series adds the devicetree configuration needed for pinctrl on
dra7 variants to use the SDHCI SDIO driver instead of mmc-omap-hs
driver. To use SDHCI, both the pins and the iodelay needs to be
configured.
This series is based on the related SDHCI drivers changes on a branch
set up by Ulf.
-----BEGIN PGP SIGNATURE-----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=lz73
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/dt-sdhci-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omap variants for SDHCI
This series adds the devicetree configuration needed for pinctrl on
dra7 variants to use the SDHCI SDIO driver instead of mmc-omap-hs
driver. To use SDHCI, both the pins and the iodelay needs to be
configured.
This series is based on the related SDHCI drivers changes on a branch
set up by Ulf.
* tag 'omap-for-v4.18/dt-sdhci-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (28 commits)
Documentation: ARM: Add new MMC requirements for DRA7/K2G
ARM: dts: dra7: Add high speed modes capability to MMC1/MMC2 dt node
ARM: dts: dra7: Use sdhci-omap programming model
ARM: dts: dra76-evm: Add wilink8 wlan support
ARM: dts: dra7-evm: Add wilink8 wlan support
ARM: dts: dra7-evm: Model EVM_3V6 regulator
ARM: dts: dra72-evm-common: Add wilink8 wlan support
ARM: dts: am57xx-beagle-x15/am57xx-idk: Fix pinctrl-names
ARM: dts: am574x-idk: Add pinmux configuration for MMC
ARM: dts: dra71-evm: Use pinctrl group from dra7-mmc-iodelay.dtsi to select pulldown
ARM: dts: am57xx-idk: Use pinctrl group from dra7-mmc-iodelay.dtsi to select pulldown
ARM: dts: dra7-mmc-iodelay: Add a new pinctrl group for clk line without pullup
ARM: dts: dra71-evm: Add "vqmmc-supply" property for mmc2
ARM: dts: dra72-evm-common: Remove mmc specific pinmux
mmc: sdhci-omap: Get IODelay values for 3.3v DDR mode
dt-bindings: sdhci-omap: Add pinctrl bindings
mmc: sdhci-omap: Add sdhci_omap specific ops for enable_sdio_irq
mmc: sdhci-omap: Add support for MMC/SD controller in k2g SoC
dt-bindings: sdhci-omap: Add K2G specific binding
mmc: sdhci-omap: Workaround for Errata i834
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about the use of IRQ_TYPE_NONE")
kernel is complaining about the IRQ_TYPE_NONE usage which shouldn't
be used.
Use IRQ_TYPE_LEVEL_HIGH instead.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The NAND compatible "denali,denal-nand-dt" property has never been used and
is obsolete. Remove it.
Cc: stable@vger.kernel.org
Fixes: f549af06e9b6("ARM: dts: socfpga: Add NAND device tree for Arria10")
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The compatible string for the Denali NAND controller is incorrect,
fix it by replacing it with one matching the DT bindings and the
driver.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: d837a80d19 ("ARM: dts: socfpga: add nand controller nodes")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
The Denali NAND x-clock should be supplied by nand_x_clk, not by
nand_clk. Fix this, otherwise the Denali driver gets incorrect
clock frequency information and incorrectly configures the NAND
timing.
Cc: stable@vger.kernel.org
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: d837a80d19 ("ARM: dts: socfpga: add nand controller nodes")
Cc: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Enable support for the ARM Performance Monitor Units in the Cortex-A7
CPU cores on RZ/G1E by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on RZ/G1M by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A7
CPU cores on R-Car E2 by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on R-Car M2-N by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on R-Car V2H by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
CPU cores on R-Car M2-W by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A15
and Cortex-A7 CPU cores on R-Car H2 by adding device nodes for the two
PMUs.
New Linux output:
hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
hw perfevents: /pmu-1: failed to probe PMU!
hw perfevents: /pmu-1: failed to register PMU devices!
The last two lines are due to the Cortex-A7 CPU cores being described in
DT, but not enabled by the firmware.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable support for the ARM Performance Monitor Units in the Cortex-A9
CPU core on RZ/A1H by adding a device node for the PMU.
New Linux output:
hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to table 7.3 ("List of Interrupt IDs") in the RZ/A1H Hardware
User's Manual rev. 3.00, the realtime clock interrupts are level not
edge interrupts.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
According to table 7.3 ("List of Interrupt IDs") in the RZ/A1H Hardware
User's Manual rev. 3.00, the watchdog timer interrupt is a level
interrupt.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMU node references two interrupts, but lacks the interrupt-affinity
property, which is required in that case:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Add the missing property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMU node references two interrupts, but lacks the interrupt-affinity
property, which is required in that case:
hw perfevents: no interrupt-affinity property for /pmu, guessing.
Add the missing property to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Mobile APE6 (r8a73a4) contains four Cortex-A15 and four Cortex-A7
cores, hence the second interrupt specifier cell for Private Peripheral
Interrupts should use "GIC_CPU_MASK_SIMPLE(8)", so GIC interrupts are
delivered to all 8 processor cores.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
R-Car H2 (r8a7790) contains four Cortex-A15 and four Cortex-A7 cores,
hence the second interrupt specifier cell for Private Peripheral
Interrupts should use "GIC_CPU_MASK_SIMPLE(8)", to make sure interrupts
can be delivered to all 8 processor cores.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instead of hardcoding the input codes we can use the symbol name for
better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of hardcoding the input codes we can use the symbol name for
better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Instead of hardcoding the input codes we can use the symbol name for
better readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OF graph endpoint connections must be bidirectional and dtc will now
warn if they are not. i.MX7 based DTs have an error and generate
warnings:
Warning (graph_endpoint): /replicator/ports/port@0/endpoint: graph connection to node '/soc/tpiu@30087000/port/endpoint' is not bidirectional
Warning (graph_endpoint): /soc/tpiu@30087000/port/endpoint: graph connection to node '/replicator/ports/port@1/endpoint' is not bidirectional
This appears to be a copy-n-paste error and the TPIU input should be
connected to replicator port 0 instead of port 1.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Single child nodes in OF graph don't need an address and now dtc will
warn about this:
Warning (graph_child_address): /soc/aips@50000000/ldb@53fa8008/lvds-channel@0: graph node has single child node 'port@0', #address-cells/#size-cells are not necessary
Since the LDB should always have an output port, fix the warning by
adding the output port, 2, to the DT.
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
OF graph endpoint nodes are supposed to be named 'endpoint' with an
address if there is more than one. The i.MX IPU binding graph has used
unique endpoint names instead which now generate dtc warnings:
Warning (graph_endpoint): /soc/ipu@2400000/port@2/disp0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@2/hdmi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@2/mipi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@2/lvds0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@2/lvds1-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@3/disp1-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@3/hdmi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@3/mipi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@3/lvds0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2400000/port@3/lvds1-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@2/disp0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@2/hdmi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@2/mipi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@2/lvds0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@2/lvds1-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@3/hdmi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@3/mipi-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@3/lvds0-endpoint: graph endpont node name should be 'endpoint'
Warning (graph_endpoint): /soc/ipu@2800000/port@3/lvds1-endpoint: graph endpont node name should be 'endpoint'
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add the 4th partiton named "mfg" with a block size 64K to store
manufacturing data.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It replaces underscore with hyphen in aliases name to fix DTC
alias_paths warning below, which is seen with various i.MX board dts
files when W=1 switch is on.
Warning (alias_paths): /aliases: aliases property name must include only lowercase and '-'
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Gary Bisson <gary.bisson@boundarydevices.com>
For soc level of clocks which are input to Clock Control Module, clock
driver expects them to be under 'clocks' container node. But for board
level clocks, this container is not really necessary. Let's drop it and
use an unique name for fixed rate clock, so that 'reg' property can be
saved as well.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-By: Lothar Waßmann <LW@KARO-electronics.de>
Instead of copying the whole node hierarchy, let's define a label for
clock osc26m in soc dtsi and use it for overriding clock-frequency.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The clk32 clock is an input clock to CCM module, and should be defined
in soc dtsi rather than a board level dts. Let's move it into
imx1.dtsi.
While at it, let's drop unnecessary #address-cells/#size-cells from
'clocks' node to DTC warning avoid_unnecessary_addr_size seen with W=1
switch.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It drops unnecessary #address-cells/#size-cells from <soc>.dtsi 'clocks'
node to fix DTC warning avoid_unnecessary_addr_size seen with W=1
switch.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There is a debug LED(D11) connected to GPIO1_IO24,
add support for it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SX Sabre Auto board has GPIO1_IO13 pin can be
MUXed as WDOG output to reset PMIC, add this function
support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
i.MX6SX Sabre Auto board has two max7310 IO expander on I2C3 bus, add
support for them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The board specific pinctrl function container node 'imx6x-sabreauto' is
not really necessary, since commit 5fcdf6a7ed ("pinctrl: imx: Allow
parsing DT without function nodes"). Let's drop it to save one level of
indentation.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Let's drop the 'regulators' container node by giving VCC_SD3 an unique
name and removing 'reg' property, so that the fixed regulator can be
under root node directly.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 'fsl,uart-has-rtscts' property is deprecated and it is recommended
to use the generic 'uart-has-rtscts' property instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Remove unnecessary #address-cells/#size-cells from the switch nodes
to fix the following DTC warnings:
arch/arm/boot/dts/imx6q-b450v3.dtb: Warning (avoid_unnecessary_addr_size): /mdio-gpio/switch@0: unnecessary #address-cells/#size-cells without "ranges" or child "reg" property
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO_ACTIVE_LOW was being used to specify an interrupt, use
IRQ_TYPE_EDGE_RISING instead. This improves DT readability.
Signed-off-by: Hernán Gonzalez <hernan@vanguardiasur.com.ar>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
This removes the #address-cells and #size-cells properties from the
gpio-keys node in the da850-lego-ev3 device tree. These properties are
not needed since the child nodes don't have a reg property.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This series adds support for am335x-pockebeagle and also add missing
pinctrl configuration for am335x evm and beagle bone variants.
There are also changes to add missing omap3 oscillator clocks for audio,
and fixes am437x tps65218 irq type used for various board specific
files.
There are also few minor fixes included that are not urgent. The
fixes for n8x0 audio also depend on driver changes, and the hp t410
mmc card detect mux typo is harmless.
-----BEGIN PGP SIGNATURE-----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=y/p3
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.18/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omap variants for v4.18 merge window
This series adds support for am335x-pockebeagle and also add missing
pinctrl configuration for am335x evm and beagle bone variants.
There are also changes to add missing omap3 oscillator clocks for audio,
and fixes am437x tps65218 irq type used for various board specific
files.
There are also few minor fixes included that are not urgent. The
fixes for n8x0 audio also depend on driver changes, and the hp t410
mmc card detect mux typo is harmless.
* tag 'omap-for-v4.18/dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: correct invalid I/O definition for MMC/SD card detect on T410
ARM: dts: omap2420-n810: Correct the audio codec (tlv320aic33) node
ARM: dts: omap2420-n810: Enable McBSP2 for audio
ARM: dts: am437x-sk-evm: Correct tps65218 irq type
ARM: dts: am437x-epos-evm: Correct tps65218 irq type
ARM: dts: am437x-cm-t43: Correct tps65218 irq type
ARM: dts: am437x-gp-evm: Correct tps65218 irq type
ARM: dts: Add am335x-pocketbeagle
ARM: dts: am33xx: Add pinmux data for mmc1 in am335x-evm, evmsk and beaglebone
ARM: dts: omap3-gta04: Add fixed 26MHz clock as fck for twl
ARM: dts: omap3-pandora: Add fixed 26MHz clock as fck for twl
ARM: dts: omap3-beagle-xm: Add fixed 26MHz clock as fck for twl
ARM: dts: logicpd-som-lv: Enable Touchscreen controller
Signed-off-by: Olof Johansson <olof@lixom.net>
Highlights:
-----------
-MCU platforms updates:
-Update pwm-cells for stm32h743
-Add I2C support on stm32f7xx-disco boards and
on stm32h743i-eval board
-Add new stm32f469 dtsi file
-Add display support on stm32f469-disco (LTDC/DSI)
+ pannel orisetech (otm8009a)
-MPU STM32MP157 platform updates:
-Fix DTC (W=12) warnings
-Fix IRQ type definition for usart
-Add QSPI & NOR flash support on EV1 board
-Add CEC support
-Add USB host
-Add USBPHYC support and enable it on EV1 board
-Add LTDC and DSI support
-Add I2C support and enable it on ED1 and EV1 boards
-Add CRC support
-Add RNG support
-Add CRYP support
-Add DAC support
-Add LPTIMER support
-Add VREFBUFF support
-Add timers supports and enable timer trigger 6 on ED1 board
-Add MDMA, DMA and DMAMUX support and enable it
-Enable clock driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=V7P6
-----END PGP SIGNATURE-----
Merge tag 'stm32-dt-for-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into next/dt
STM32 DT updates for v4.18, round 1
Highlights:
-----------
-MCU platforms updates:
-Update pwm-cells for stm32h743
-Add I2C support on stm32f7xx-disco boards and
on stm32h743i-eval board
-Add new stm32f469 dtsi file
-Add display support on stm32f469-disco (LTDC/DSI)
+ pannel orisetech (otm8009a)
-MPU STM32MP157 platform updates:
-Fix DTC (W=12) warnings
-Fix IRQ type definition for usart
-Add QSPI & NOR flash support on EV1 board
-Add CEC support
-Add USB host
-Add USBPHYC support and enable it on EV1 board
-Add LTDC and DSI support
-Add I2C support and enable it on ED1 and EV1 boards
-Add CRC support
-Add RNG support
-Add CRYP support
-Add DAC support
-Add LPTIMER support
-Add VREFBUFF support
-Add timers supports and enable timer trigger 6 on ED1 board
-Add MDMA, DMA and DMAMUX support and enable it
-Enable clock driver
* tag 'stm32-dt-for-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (42 commits)
ARM: dts: stm32: update pwm-cells for LPTimer on stm32h743
ARM: dts: stm32: Add I2C1 support for stm32h743i-eval Board
ARM: dts: stm32: Add I2C support for STM32H743 SoC
ARM: dts: stm32: Add I2C1 support for stm32f746-disco Board
ARM: dts: stm32: Add I2C1 support for stm32f769-disco Board
ARM: dts: stm32: Append additional I2Cs for STM32F746 SoC
ARM: dts: stm32: Add display support on stm32f469-disco
ARM: dts: stm32: Add new stm32f469 dtsi file with mipi dsi
ARM: dts: stm32: Use gpio bindings in stm32f469-disco
ARM: dts: stm32: Fix IRQ_TYPE_NONE warnings on stm32mp157c
ARM: dts: stm32: Fix DTC warnings for stm32mp157
ARM: dts: stm32: add flash nor support on stm32mp157c eval board
ARM: dts: stm32: add qspi support for stm32mp157c
ARM: dts: stm32: add cec support on stm32mp157c-ev1
ARM: dts: stm32: add cec pins to stm32mp157c
ARM: dts: stm32: add cec support on stm32mp157c
ARM: dts: stm32: add USB Host (USBH) support to stm32mp157c
ARM: dts: stm32: enable USBPHYC on stm32mp157c-ev1
ARM: dts: stm32: add supplies to usbphyc ports on stm32mp157c-ed1
ARM: dts: stm32: add USBPHYC support to stm32mp157c
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Corrects the debounce interval on some nodes
- Drops the U8540/U9540 device trees
-----BEGIN PGP SIGNATURE-----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=OYnk
-----END PGP SIGNATURE-----
Merge tag 'ux500-dts-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
This:
- Corrects the debounce interval on some nodes
- Drops the U8540/U9540 device trees
* tag 'ux500-dts-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: Drop the U8540 device trees
ARM: dts: Ux500: Fix "debounce-interval" property misspelling
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add missing 'fsl,sec-era' property for i.MX7S device tree CAAM node,
as the era information is used in various places inside CAAM driver.
- There are a few errors in imx51-zii-rdu1 device tree touchscreen
node. Fix them to get touchscreen actually work.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJa+SwfAAoJEFBXWFqHsHzOgO0H/3SfW3P816gDaJAPmKIt+2t8
XN7bVjJKwC6dv16L6Qf4R5xkdZwMFqelU9euObl/mDoXZvhk1IWLgmMfJJewTzDQ
fztoRU5kFMbOrmWItjrhsw0SV+mhqEpNdQ+HP1KKU4YNDepHA+xvvGN3KttlM7OT
XsNtKbFyYlwaHaU5qwcfTQxwmdsXSoNlZa727KXULQ5v7BTP9w+t8BPDbSfUezQe
mYcXx0IPytHjp7UU57ZmNiPRNPtSQA6ZaEPkzk9oNvnF2wIAdYKg8leqyB8/4xhR
nIprdefB2A9dODnLr4u0Gtn4YgMbbwRHzswbX2qMjgUob/H27n6Sg1QYol7Pcys=
=dU4h
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
i.MX fixes for 4.17:
- Add missing 'fsl,sec-era' property for i.MX7S device tree CAAM node,
as the era information is used in various places inside CAAM driver.
- There are a few errors in imx51-zii-rdu1 device tree touchscreen
node. Fix them to get touchscreen actually work.
* tag 'imx-fixes-4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-zii-rdu1: fix touchscreen bindings
ARM: dts: imx7s: Pass the 'fsl,sec-era' property
Signed-off-by: Olof Johansson <olof@lixom.net>
This series of patches contains one BUG fix for trace if
CONFIG_DEBUG_PREEMPT is enabled and a regression fix for omap1 FIQ
handling on ams-delta. Then there's a dts fix for missing SoC
compatible on ti81xx board dts files that did matter until we added
the clkctrl clocks and without that some clocks are now not found.
Then there are two logicpd-som-lv specific dts fixes that fix
misconfigured pins for WLAN and audio. Turns out we had to revert
the third one because it caused another regression for USB.
-----BEGIN PGP SIGNATURE-----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=SBDB
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v17/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omap variants for v4.17
This series of patches contains one BUG fix for trace if
CONFIG_DEBUG_PREEMPT is enabled and a regression fix for omap1 FIQ
handling on ams-delta. Then there's a dts fix for missing SoC
compatible on ti81xx board dts files that did matter until we added
the clkctrl clocks and without that some clocks are now not found.
Then there are two logicpd-som-lv specific dts fixes that fix
misconfigured pins for WLAN and audio. Turns out we had to revert
the third one because it caused another regression for USB.
* tag 'omap-for-v17/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
Revert "ARM: dts: logicpd-som-lv: Fix pinmux controller references"
ARM: dts: correct missing "compatible" entry for ti81xx SoCs
ARM: OMAP1: ams-delta: fix deferred_fiq handler
ARM: dts: logicpd-som-lv: Fix pinmux controller references
ARM: dts: logicpd-som-lv: Fix Audio Mute
ARM: dts: logicpd-som-lv: Fix WL127x Startup Issues
ARM: OMAP2+: powerdomain: use raw_smp_processor_id() for trace
Signed-off-by: Olof Johansson <olof@lixom.net>
4.17, please pull the following:
- Clement fixes in an incorrect trigger type for the ARM global timers
on the Cygnus platforms
-----BEGIN PGP SIGNATURE-----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=uM7v
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.17/devicetree-fixes' of https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM-basec SoCs Device Tree fixes for
4.17, please pull the following:
- Clement fixes in an incorrect trigger type for the ARM global timers
on the Cygnus platforms
* tag 'arm-soc/for-4.17/devicetree-fixes' of https://github.com/Broadcom/stblinux:
ARM: dts: cygnus: fix irq type for arm global timer
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a single revert for a patch that was merged in v4.17-rc1
and that turns out to cause a regression on some boards. Further, the
original issue that the patch was supposed to fix seems to have
disappeared.
-----BEGIN PGP SIGNATURE-----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=dgSr
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into fixes
ARM: tegra: Device tree fixes for v4.17
This contains a single revert for a patch that was merged in v4.17-rc1
and that turns out to cause a regression on some boards. Further, the
original issue that the patch was supposed to fix seems to have
disappeared.
* tag 'tegra-for-4.17-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: dts: tegra20: Revert "Fix ULPI regression on Tegra20"
Signed-off-by: Olof Johansson <olof@lixom.net>
Fix LVDS output on Gen2 boards
Laurent Pincart says "This patch series fixes LVDS output support on the
Lager, Koelsh, Porter and Gose boards that broke in v4.17-rc1 due to the
combination of the R-Car DU LVDS driver rework and the DT move of all
on-SoC peripherals to a /soc node.
We could handle the problem in the R-Car DU LVDS DT backward compatibility
code, but that fix would only be used for v4.17 as in v4.18 the Gen2 DT
will move to the new LVDS DT bindings. I thus propose merging these three
patches in v4.17 already to fix the problem as this is the simplest
solution."
-----BEGIN PGP SIGNATURE-----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=FqQ5
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes-for-v4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Renesas ARM Based SoC Fixes for v4.17
Fix LVDS output on Gen2 boards
Laurent Pincart says "This patch series fixes LVDS output support on the
Lager, Koelsh, Porter and Gose boards that broke in v4.17-rc1 due to the
combination of the R-Car DU LVDS driver rework and the DT move of all
on-SoC peripherals to a /soc node.
We could handle the problem in the R-Car DU LVDS DT backward compatibility
code, but that fix would only be used for v4.17 as in v4.18 the Gen2 DT
will move to the new LVDS DT bindings. I thus propose merging these three
patches in v4.17 already to fix the problem as this is the simplest
solution."
* tag 'renesas-fixes-for-v4.17' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r8a7793: Convert to new LVDS DT bindings
ARM: dts: r8a7791: Convert to new LVDS DT bindings
ARM: dts: r8a7790: Convert to new LVDS DT bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
The mms114 binding [1] specifies that the 'x' and 'y' should be
called respectively 'touchscreen-size-x' and 'touchscreen-size-y'
in coherence with the touchscreen [2] binding.
Update the mms114 node for trats2 and trats dts according to the
binding.
[1] Documentation/devicetree/bindings/input/touchscreen/mms114.txt
[2] Documentation/devicetree/bindings/input/touchscreen/touchscreen.txt
Signed-off-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
There are 3 scaler devices in Exynos5420 SoCs, all are a part of MSCL
power domain. MSCL power domain and SYSMMU controllers (two per each
scaler device) have been already added to exynos5420.dtsi earlier,
so bind them to newly added devices.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The DTC was warning a lot about unit names etc, I think I fixed
them all. Stopping to include skeleton.dtsi fixes the last one.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The NAS4220B has the second ATA interface up and running.
Activate it in the device tree.
Signed-off-by: Roman Yeryomin <roman@advem.lv>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These machines need to be booted from very specific harddisk
partitions (as the D-Link DNS-313 boots specifically from
partition 4). Add the proper bootargs so that everything works
smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The flash on the DNS-313 needs to be probed as JEDEC, it does
not conform to the common CFI standard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Using the blue LED for disk read and the orange LED for
disk write gives a better user experience.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We just used one LED for "disk activity" but using the green
LED for disk read and the red LED for disk write gives a way
better user experience.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This new syntax is slightly better designed & uses "compatible" string.
For details see Documentation/devicetree/bindings/mtd/partition.txt .
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add MT7623N reference board with eMMC. On the board, there is additional
external PHY ICPlus IP1001 transceiver available by port 5 on the MDIO
bus connectted with GMAC2.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add MT7623A reference board with eMMC and NAND, respectively.
The both boards compared against MT7623N BPI-R2, we could see there are
UART[0-1] and USB2 being removed, I2C2 and SPI1 being added, I2C1, UART2
owning distinct pin usage and an extra WM8960 codec chip plugged into the
I2C1 offering the functionality of audio player and recorder through
SoC audio front-end engine (AFE).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Suggested-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add a common file for MT7623A SoC level DTS, indicating MT7623A only
has a specific definition for power domain. That causes we need to change
related consumers devices such as audio, ethernet, crypto, NAND, and USB
controller to grasp its own power domain it should belong to.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Move all possible setups for pio into SoC level DTSI file mt7623.dtsi in
order to introduce more boards such as official MT7623A reference boards
without copy-n-pasting almost the same content of nodes in pio into every
new file.
So, it should be better to reuse those nodes by consolidating them into
the common file mt7623.dtsi from the current existent DTS and allow new
DTS files to refer to them.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Since those LEDs are parts of PMIC MT6323, it is reasonable to merge
those LEDs node definition back into mt6323.dtsi. This way can improve
the reusability of those nodes among different boards with the same PMIC.
And LED is very much board specific and thus the mt6323.dtsi only includes
the parent node here and leave these child nodes in the board specific
dts file.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
add BTIF, HSDMA and SPI-NOR device nodes and enable it on relevant boards
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Fix below a lot of Warnings (unit_address_vs_reg) that dtc complains so
much for
Node /oscillator@1 has a unit name, but no reg property
Node /oscillator@0 has a unit name, but no reg property
Node /pinctrl@10005000/cir@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2c@1 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@0 has a unit name, but no reg property
Node /pinctrl@10005000/i2s@1 has a unit name, but no reg property
Node /pinctrl@10005000/keys@0 has a unit name, but no reg property
Node /pinctrl@10005000/leds@0 has a unit name, but no reg property
Node /pinctrl@10005000/pwm@0 has a unit name, but no reg property
Node /pinctrl@10005000/spi@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@0 has a unit name, but no reg property
Node /pinctrl@10005000/uart@1 has a unit name, but no reg property
Node /pinctrl@10005000/uart@2 has a unit name, but no reg property
Node /ethernet@1b100000/mdio-bus/switch@0/ports has a reg or ranges
property, but no unit name
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
There is 2GB DDR3 available on bananapi-r2 board as [1] specified.
[1] http://www.banana-pi.org/r2.html
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Below two wrong nodes in existing DTS files would cause a fail boot since
in fact the address 0 is not the correct place the memory device locates
at.
memory {
device_type = "memory";
reg = <0x0 0x0 0x0 0x0>;
};
memory@80000000 {
reg = <0x0 0x80000000 0x0 0x40000000>;
};
In order to avoid having a memory node starting at address 0, we can't
include file skeleton64.dtsi and instead need to explicitly manually
define a few of properties the DTS relies on such as #address-cells
and #size-cells in root node and device_type in the node memory@80000000.
Cc: stable@vger.kernel.org
Fixes: 31ac0d69a1 ("ARM: dts: mediatek: add MT7623 basic support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
The latest DTC throws warnings for character '_' in the node names.
Warning (node_name_chars_strict): /pmu_a15: Character '_' not recommended in node name
Warning (node_name_chars_strict): /pmu_a7: Character '_' not recommended in node name
The general recommendation is to use character '-' for all the node names.
This patch fixes the warnings following the recommendation.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Commit 2cff6dba57 ("ARM: dts: vexpress: fix node name unit-address presence warnings")
removed the unit address as there was no associated reg property in
these sysreg nodes.
Also the latest DTC throws warnings for character '_' in the node names.
Warning (node_name_chars_strict): /sysreg@10000/sys_led: Character '_' not recommended in node name
Warning (node_name_chars_strict): /sysreg@10000/sys_mci: Character '_' not recommended in node name
Warning (node_name_chars_strict): /sysreg@10000/sys_flash: Character '_' not recommended in node name
The correct way to fix this as well as the original unit-address presence
warnings is to use the standard gpio controller binding and specify the
reg properties as per the hardware as it was before.
However note that Vexpress sysreg MFD driver will still continue to use
the hardcoded values for compatibility reasons.
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Suggested-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add SY8106A regulator to r_i2c bus and enable the r_i2c bus on
Orange Pi PC, then set the power supply of the ARM cores to this
regulator, in order to enable DVFS.
Signed-off-by: Ondrej Jirman <megous@megous.com>
[Icenowy: Enable DVFS in this patch, slight changes and change commit
message]
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The Tronsmart MXIII Plus is an Android TV box which uses the Amlogic
S812 (Meson8m2) SoC. It uses a Realtek RTL8211F RGMII Ethernet PHY as
well as a Ricoh RN5T618 system power controller. It also comes with an
Ampak AP6330 SDIO wifi/Bluetooth combo chip (support for wifi and
Bluetooth is currently not added because the Linux drivers currently
only support one MMC controller and that is used for the SD card).
Signed-off-by: Oleg Ivanov <balbes-150@yandex.ru>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds the pins for uart_A, which is used to connect to the Bluetooth
module on some devices.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This adds a meson8m2.dtsi which simply inherits meson8.dtsi as both SoCs
share most peripherals.
The known differences are:
- Meson8m2's hardware video decoder additionally supports H.265 decoding
- Meson8m2 has the same Gigabit MAC as Meson8b (instead of the 10/100M
MAC that Meson8 uses)
- Meson8m2 uses the same watchdog register layout/bits as Meson8b (using
the Meson8 watchdog compatible leads to an infinite hang when
rebooting the machine)
- Meson8m2 uses the same SAR ADC register layout/bits as Meson8b.
However, it uses the temperature sensor calibration formula (and
registers) Meson8b which differ from Meson8. This however is currently
not supported by the meson-saradc driver yet.
- the pin controller is mostly compatible with Meson8, Meson8m2 has
an additional function on eight pins and removes the "VGA" function.
So there's a total of 10 pins which are slightly changed, which is why
there's a separate compatible for the pin controller
- a separate compatible for the clock controller is used because at
least the Mali clock tree (not supported yet) is the same as on GXBB
while Meson8 and Meson8b have a reduced/older version of the Mali
clock tree.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Many node labels in the device tree (like serial0, serial1, etc) are being
redefined, so let's modernize the device tree by using phandles to
extend the existing nodes. This helps reduce the whitespace.
Signed-off-by: Adam Ford <aford173@gmail.com>
[nsekhar@ti.com: drop tps6507x related changes]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The Odroid-C1 comes with an IR receiver. It is connected to the GPIOAO_7
pin and thus using the SoC's internal IR decoder.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This makes it easier to find existing nodes. No functional changes.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes is clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
This file were created and ever touched by a group of three people only:
Álvaro, Hauke and me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It's an access point based on BCM47094 SoC with two BCM4366E wireless
chipsets.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Luxul XWR-3150 is a wireless router similar to the XWR-3100 except:
1) It has more RAM
2) Its NAND controller in running in BCH8 mode
3) LAN ports LEDs are hardware controlled
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Acked-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
It is a bit unorthodox to just include a file in the middle of a another
DTS file, it breaks the pattern from other device trees and also makes
it really hard to reference things across the files with phandles.
Restructure the include for the Versatile Express motherboards to happen
at the top of the file, reference the target nodes directly, and indent
the motherboard .dtsi files to reflect their actual depth in the
hierarchy.
This is a purely syntactic change that result in the same DTB files from
the DTS/DTSI files.
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Mali DP Maintainers <malidp@foss.arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Add the use of enable-method property for SMP support which allows
to handle the SMP support for this specific SoC.
This commit adds enable-method properties to all CPU nodes.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The R_CPUCFG is a collection of registers needed for SMP bringup
on clusters and cluster's reset.
For the moment, documentation about this register is found in
Allwinner's code only.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
As we found in sun9i-a80, CPUCFG is a collection of registers that are
mapped to the SoC's signals from each individual processor core and
associated peripherals.
These registers are used for SMP bringup and CPU hotplugging.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Same EEPROM as on Koelsch, et al.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit d50f4630c2 ("arm: dts: Remove p1010-flexcan compatible from imx
series dts") removed the fallback compatible "fsl,p1010-flexcan" from
the imx device trees. As the flexcan cores on i.MX25, i.MX35 and i.MX53
are identical, introduce the first as fallback for the two latter ones.
Fixes: d50f4630c2 ("arm: dts: Remove p1010-flexcan compatible from imx series dts")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= v4.16
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Remove the usage of skeleton.dtsi to fix the DTC warnings:
arch/arm/boot/dts/s3c6410-mini6410.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
arch/arm/boot/dts/s3c6410-smdk6410.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Remove the usage of skeleton.dtsi to fix the DTC warning:
arch/arm/boot/dts/s3c2416-smdk2416.dtb: Warning (unit_address_vs_reg):
/memory: node has a reg or ranges property, but no unit name
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
As per ARM documentation
PPI(0) ID27 - global timer interrupt is rising-edge sensitive.
set IRQ triggering type to IRQ_TYPE_EDGE_RISING for ARM Global timers.
Fixes: c9ad7bc5fe ("ARM: dts: Enable Broadcom Cygnus SoC")
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This matches licensing used by other BCM5301X files and is preferred as:
1) GPL 2.0+ makes is clearly compatible with Linux kernel
2) MIT is also permissive but preferred over ISC
These files were created and ever touched by a group of four people
only: Felix, INAGAKI, Hauke and me.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Felix Fietkau <nbd@nbd.name>
Acked-by: INAGAKI Hiroshi <musashino.open@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Currently the following error is seen from the CAAM driver:
caam 30900000.caam: device ID = 0x0a16030000000000 (Era -524)
Pass the 'fsl,sec-era' property to properly describe the
era information.
This error happens because the 'fsl,sec-era' is not passed via
device tree.
The era information is used in various places inside drivers/crypto/caam,
so pass the correct version via device tree.
Fixes: 0eeabcad7d ("ARM: dts: imx7s: add CAAM device node")
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The 66AK2G evm has support for dcan.
Add nodes and pinmuxes for dcan0 and dcan1.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Commit 4c9a27a6c6 ("ARM: tegra: Fix ULPI regression on Tegra20") changed
"ulpi-link" clock from CDEV2 to PLL_P_OUT4. Turned out that PLL_P_OUT4 is
the parent of CDEV2 clock and original clock setup of "ulpi-link" was
correct. The reverted patch was fixing USB for one board and broke the
other, now Tegra's clk driver correctly sets parent for the CDEV2 clock
and hence patch could be reverted safely, restoring USB for all of the
boards.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marcel Ziswiler <marcel@ziswiler.com>
Tested-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The U8540 was an evolved version of the U8500, but it was never
mass produced or put into products, only reference designs exist.
The upstream support was never completed and it is unlikely that
this will happen so drop the support for now to simplify
maintenance of the U8500.
Cc: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
LPTimer pwm cells should be updated to 3, to allow initialization of
channel, period and polarity.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add display support on the stm32f469-disco board.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
In the stm32f4 family, mipi dsi is only supported on stm32f469.
So add a new stm32f469 dtsi file & add mipi dsi support inside.
Signed-off-by: Philippe Cornu <philippe.cornu@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Since commit 83a86fbb5b ("irqchip/gic: Loudly complain about
the use of IRQ_TYPE_NONE"), a warning is raised if IRQ_TYPE_NONE is used.
So we use IRQ_TYPE_LEVEL_HIGH for usart nodes instead of IRQ_TYPE_NONE.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Tested-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Fix DTC warnings for stm32mp157:
Warning (unit_address_vs_reg): /soc/pin-controller: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /soc/pin-controller/uart4@0: node has a unit name, but no reg property
Warning (unit_address_vs_reg): /soc/pin-controller-z: node has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): /memory: node has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds flash nor on qspi. Each flash is
connected in quad mode and has its own chip select.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This patch adds qspi support on stm32mp157c,
read in memory mapped, write in indirect mode.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for USBH (USB Host) to STM32MP157C SoC.
USBH is a USB Host controller supporting the standard registers used for
full- and low-speed (OHCI controller) and high-speed (EHCI controller).
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
This patch enables USBPHYC (USB PHY Controller) on stm32mp157c-ev1.
This enables the two usbphyc usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for USBPHYC (USB PHY Controller) to STM32MP157C SoC.
It manages two usb2 ports.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Add support for the display controller ltdc.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
These files were created and ever touched by a group of three people
only: Dan, Hauke and me. They were licensed under GNU/GPL or ISC.
Introducing and discussing SPDX-License-Identifier resulted in a
conclusion that ISC is a not recommended license (see also a
license-rules.rst). Moveover an old e-mail from Alan Cox was pointed
which explained that dual licensing is a safer solution than depending
on a common compatibility belief.
This commit switches most of BCM5301X DTS files to dual licensing using:
1) GPL 2.0+ to make sure they are compatible with Linux kernel
2) MIT to allow sharing with more permissive projects
Both licenses belong to the preferred ones (see LICENSES/preferred/).
An attempt to relicense remaining files will be made separately and will
require approve from more/other developers.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Dan Haab <dan.haab@luxul.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Improve the DTS files by removing all the leading "0x" and zeros to fix the
following dtc warnings:
Warning (unit_address_format): Node /XXX unit name should not have leading "0x"
Warning (unit_address_format): Node /XXX unit name should not have leading 0s
Converted using the following command:
find arch/arm/boot/dts -type f \( -iname "*.dts" -o -iname "*.dtsi" \) -exec sed -i \
-e "s/@\([0-9a-fA-FxX\.;:#]\+\)\s*{/@\L\1 {/g" -e "s/@0x\(.*\) {/@\1 \
{/g" -e "s/@0\+\(.\+\) {/@\1 {/g" {} +
For simplicity, two sed expressions were used to solve each warnings separately.
To make the regex expression more robust a few other issues were resolved,
namely setting unit-address to lower case, and adding a whitespace before the
the opening curly brace: https://elinux.org/Device_Tree_Linux#Linux_conventions
This will solve also a side effect warning:
Warning (simple_bus_reg): Node /XXX@<UPPER> simple-bus unit address format error, expected "<lower>"
This is a follow up to commit 4c9847b737 ("dt-bindings: Remove leading 0x from bindings notation")
Reported-by: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mathieu Malaterre <malat@debian.org>
[krzk: Rerun the command to include few more changes, adjust the commit msg]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
