Replace driver internally coded enabling/disabling of the
analog-filter with the DT binding "i2c-analog-filter".
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When the driver starts to send a message with the MASTER_ID field
set (high speed), the whole I2C_ADDR register is overwritten including
MASTER_ID as the SLV_ADDR_MAS field is set.
This patch preserves already written fields in I2C_ADDR when writing
SLV_ADDR_MAS.
Fixes: 8a73cd4cfa ("i2c: exynos5: add High Speed I2C controller driver")
Signed-off-by: Mårten Lindahl <martenli@axis.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit e0371298dd. It was
accidently applied despite discussion still going on.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Stephen Boyd <swboyd@chromium.org>
IC_DATA_CMD[11] indicates the first data byte received after the address
phase for receive transfer in Master receiver or Slave receiver mode,
this bit was set in some transfer flow. IC_DATA_CMD[7:0] contains the
data to be transmitted or received on the I2C bus, so we should use the
lower 8 bits to get the real data length.
Signed-off-by: Liguang Zhang <zhangliguang@linux.alibaba.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The brcmstb_send_i2c_cmd currently has a condition that is (CMD_RD ||
CMD_WR) which always evaluates to true, while the obvious fix is to test
whether the cmd variable passed as parameter holds one of these two
values.
Fixes: dd1aa2524b ("i2c: brcmstb: Add Broadcom settop SoC i2c controller driver")
Reported-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
Pull i2c updates from Wolfram Sang:
- mostly driver updates. Bigger ones for mlxcpld and iproc. But most of
them are all over the place.
- removal of the efm32, sirf, u300, and zte zx bus drivers because of
platform removal. So, we have a pleasant diffstat this time.
- first set of cleanups in the I2C core as preparation to increase
maximum length of SMBus transfers to 255 (as specified in the new
standard). Better documentation of struct i2c_msg and its flags stand
out here.
- the testunit can now respond to SMBus block process calls which is
the testcase when implementing the above new maximum length.
* 'i2c/for-5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (62 commits)
i2c: remove redundant error print in stm32f7_i2c_probe
i2c: testunit: add support for block process calls
i2c: busses: Replace spin_lock_irqsave with spin_lock in hard IRQ
dt-bindings: eeprom: at24: Document ROHM BR24G01
i2c: i801: Add support for Intel Alder Lake PCH-P
i2c: mv64xxx: Fix check for missing clock after adding RPM
i2c: mux: mlxcpld: Add callback to notify mux creation completion
i2c: mux: mlxcpld: Extend supported mux number
i2c: mux: mlxcpld: Extend driver to support word address space devices
i2c: mux: mlxcpld: Get rid of adapter numbers enforcement
i2c: mux: mlxcpld: Prepare mux selection infrastructure for two-byte support
i2c: mux: mlxcpld: Convert driver to platform driver
i2c: imx: Synthesize end of transaction events without idle interrupts
i2c: i2c-qcom-geni: Add shutdown callback for i2c
i2c: mv64xxx: Add runtime PM support
i2c: amd-mp2: Remove unused macro
i2c: amd-mp2: convert to PCI logging functions
i2c: mux: mlxcpld: Move header file out of x86 realm
platform/x86: mlxcpld: Update module license
i2c: mux: mlxcpld: Update module license
...
A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
* ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
* HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
* ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions and
fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
* Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support
-----BEGIN PGP SIGNATURE-----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=QgvS
-----END PGP SIGNATURE-----
Merge tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions
and fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support"
* tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits)
ALSA: hda: intel-dsp-config: add Alder Lake support
ASoC: soc-pcm: fix hw param limits calculation for multi-DAI
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: soc-pcm: fix hwparams min/max init for dpcm
ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup
ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10
ALSA: hda: Add another CometLake-H PCI ID
ASoC: soc-pcm: add soc_pcm_hw_update_format()
ASoC: soc-pcm: add soc_pcm_hw_update_chan()
ASoC: soc-pcm: add soc_pcm_hw_update_rate()
ASoC: wm_adsp: Remove unused control callback structure
ASoC: SOF: relax ABI checks and avoid unnecessary warnings
ASoC: codecs: lpass-tx-macro: add dapm widgets and route
ASoC: codecs: lpass-tx-macro: add support for lpass tx macro
ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec
ASoC: codecs: lpass-rx-macro: add iir widgets
ASoC: codecs: lpass-rx-macro: add dapm widgets and route
...
There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use [1], and
received confirmation about six ARM platforms and the TI C6x architecture
that have all reached the end of their life upstream, with no known
users remaining:
- efm32 -- added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell -- added in 2011, abandoned after 2012 acquisition
- prima2 -- added in 20111, no notable changes since 2015
- tango -- added in 2015, sporadic changes until 2017, but abandoned
- u300 -- added in 2009, no notable changes since 2013
- zx --added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x -- added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users
that plan to contribute them in the future, in other cases the code
is complete and works reliably.
[1] https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=pf3b
-----END PGP SIGNATURE-----
Merge tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform removals from Arnd Bergmann:
"There are a lot of platforms that have not seen any interesting code
changes in the past five years or more.
I made a list and asked around which ones are no longer in use, and
received confirmation about six ARM platforms and the TI C6x
architecture that have all reached the end of their life upstream,
with no known users remaining:
- efm32 - added in 2011, first Cortex-M, no notable changes after 2013
- picoxcell - added in 2011, abandoned after 2012 acquisition
- prima2 - added in 20111, no notable changes since 2015
- tango - added in 2015, sporadic changes until 2017, but abandoned
- u300 - added in 2009, no notable changes since 2013
- zx - added in 2015 for both 32, 2017 for 64 bit, no notable changes
- arch/c6x - added in 2011, but work stalled soon after that
A number of other platforms on the original list turned out to still
have users. In some cases there are out-of-tree patches and users that
plan to contribute them in the future, in other cases the code is
complete and works reliably"
Link: https://lore.kernel.org/lkml/CAK8P3a2DZ8xQp7R=H=wewHnT2=a_=M53QsZOueMVEf7tOZLKNg@mail.gmail.com/
* tag 'arm-platform-removal-v5.12' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: remove u300 platform
ARM: remove tango platform
ARM: remove zte zx platform
ARM: remove sirf prima2/atlas platforms
c6x: remove architecture
MAINTAINERS: Remove deleted platform efm32
ARM: drop efm32 platform
ARM: Remove PicoXcell platform support
ARM: dts: Remove PicoXcell platforms
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAtZ7cACgkQJNaLcl1U
h9DD5Af/eeERQ2uVOqtw0If+XL1xRYe6RewgDoNcO/l/5WxBLrBH6NbEf0OwNJeg
vzZAkUBtxmx6XiW2M/h+4ucW1OPcg5IzxIWTHfGDMlKIxzb0jgWugRnJ7sdTnOs3
c+QHnvuOT7QzZBviAIkc5uZ5thAImYF8zDyKoGF5llztmnBYymtgpnvnRNZGM0ou
76oUzSvkCFI2b0Yf6bpGok2nBVlOu82HSHOUKjXVWk+LAeiivlYGOEZpdIKEe3S8
u6atQJ29XRr52Yuc2z4xnFQTW1cIDlwj2Fk5x/z8hX+5nRhNSGuIv1l5m7TfBj3e
mCO9cltKZxly0NXysgekn95JHwwwkA==
=MJSb
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.12
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
Coccinelle reports a redundant error print in stm32f7_i2c_probe.
As 'platform_get_irq' already prints the error message, error
print here is redundant and can be removed.
Signed-off-by: Menglong Dong <dong.menglong@zte.com.cn>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The digital filter related computation are present in the driver
however the programming of the filter within the IP is missing.
The maximum value for the DNF is wrong and should be 15 instead of 16.
Fixes: aeb068c572 ("i2c: i2c-stm32f7: add driver")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There is no need to do irqsave and irqrestore in context of hard IRQ.
Signed-off-by: Weihang Li <liweihang@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID of SMBus controller on Intel Alder Lake PCH-P.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In commit e5c02cf541 ("i2c: mv64xxx: Add runtime PM support"), error
pointers to optional clocks were replaced by NULL to simplify the resume
callback implementation. However, that commit missed that the IS_ERR
check in mv64xxx_of_config should be replaced with a NULL check. As a
result, the check always passes, even for an invalid device tree.
Fixes: e5c02cf541 ("i2c: mv64xxx: Add runtime PM support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Only the Layerscape SoCs have interrupts on bus idle, which facilitate
sending events which complete slave bus transactions.
Add support for synthesizing missing events. If we see a master request,
or a newly addressed slave request, if the last event sent to the backend
was I2C_SLAVE_READ_REQUESTED, send the backend a I2C_SLAVE_READ_PROCESSED
followed by I2C_SLAVE_STOP. For all other events, send an I2C_SLAVE_STOP.
Signed-off-by: Kevin Paul Herbert <kph@platinasystems.com>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the hardware is still accessing memory after SMMU translation
is disabled (as part of smmu shutdown callback), then the
IOVAs (I/O virtual address) which it was using will go on the bus
as the physical addresses which will result in unknown crashes
like NoC/interconnect errors.
So, implement shutdown callback to i2c driver to stop on-going transfer
and unmap DMA mappings during system "reboot" or "shutdown".
Fixes: 37692de5d5 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To save power, gate the clock when the bus is inactive, during system
sleep, and during shutdown. On some platforms, specifically Allwinner
A13/A20, gating the clock implicitly resets the module as well. Since
the module already needs to be reset after some suspend/resume cycles,
it is simple enough to reset it during every runtime suspend/resume.
Because the bus may be used by wakeup source IRQ threads, it needs to
be functional as soon as IRQs are enabled. Thus, its system PM hooks
need to run in the noirq phase.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use pci_{info,warn,err,dbg} functions of the kernel's PCI API.
Remove unnecessary ndev_pdev(), ndev_name() and ndev_dev() macros.
While at it, remove useless __func__ from logging.
Signed-off-by: Richard Neumann <mail@richard-neumann.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some i2c device driver indirectly uses I2C driver when it is now
being suspended. The i2c devices driver is suspended during the
NOIRQ phase and this cannot be changed due to other dependencies.
Therefore, we also need to move the suspend handling for the I2C
controller driver to the NOIRQ phase as well.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch to use threaded interrupt context in order to avoid checking of
"are we in interrupt?" for the code that may sleep in the IRQ handler.
I2C doesn't require a very low interrupt-handling latency, hence this
change doesn't introduce any noticeable effects.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The I2C_SPRD uses Common Clock Framework thus it cannot be built on
platforms without it (e.g. compile test on MIPS with LANTIQ):
/usr/bin/mips-linux-gnu-ld: drivers/i2c/busses/i2c-sprd.o: in function `sprd_i2c_probe':
i2c-sprd.c:(.text.sprd_i2c_probe+0x254): undefined reference to `clk_set_parent'
Fixes: 4a2d5f663d ("i2c: Enable compile testing for more drivers")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver implements I2C_M_RECV_LEN, so it can advertise the SMBus
transfers needing it. This also enables client devices to check for the
RECV_LEN capability.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This driver implements I2C_M_RECV_LEN, so it can advertise the SMBus
transfers needing it. This also enables client devices to check for the
RECV_LEN capability.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The ST-Ericsson U300 platform is getting removed, so this driver is no
longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Barry Song <baohua@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The smp8758 (tango4) SoC was the last generation of set-top-box chips
to come out of Sigma Designs, and support was added by Marc Gonzalez
and Måns Rullgård between 2015 and 2017, before the company went out of
business and the products were abandoned.
The chip is used in some set-top-boxes such as the Popcorn Hour A-500,
which could have seen some adoption by hobbyists. This has not happened
in the past four years, and support for the more widely used MIPS based
SoCs was never merged at all.
Thanks to Marc and Måns for maintaining for the past years even after the
death of the platform.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/lkml/2d643ebc-09af-a809-eb3f-2aec8ecee501@free.fr/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
I2C_SMBUS_BLOCK_MAX defines already the maximum number as defined in the
SMBus 2.0 specs. No reason to add one to it.
Fixes: 886f6f8337 ("i2c: octeon: Support I2C_M_RECV_LEN")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Robert Richter <rric@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
VI I2C controller has known hardware bug where immediate multiple
writes to TX_FIFO register gets stuck.
Recommended software work around is to read I2C register after
each write to TX_FIFO register to flush out the data.
This patch implements this work around for VI I2C controller.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In order to not to start returning errors when new I2C_M flags are
added, change behavior to just ignore all flags that we don't know
about. This includes the I2C_M_DMA_SAFE flag that already exists but
causes -EINVAL to be returned for valid transactions.
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Support for this machine was just removed, so drop the now unused i2c
bus driver, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Upon a communication error, the interrupt handler can call
tegra_i2c_disable_packet_mode. This causes a sleeping poll to happen
unless the current transaction was marked atomic. Fix this by
making the poll happen atomically if we are in an IRQ.
This matches the behavior prior to the patch mentioned
in the Fixes tag.
Fixes: ede2299f71 ("i2c: tegra: Support atomic transfers")
Cc: stable@vger.kernel.org
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add support for I2C bus frequency setting according to the specific
system capability. This capability is obtained from CPLD frequency
setting register, which could be provided through the platform data.
If such register is provided, it specifies minimal I2C bus frequency
to be used for the devices attached to the I2C bus. Supported
freqeuncies are 100KHz, 400KHz, 1MHz, while 100KHz is the default.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove dev_err() messages after platform_get_irq*() failures.
drivers/i2c/busses/i2c-hix5hd2.c:417:2-9: line 417 is redundant
because platform_get_irq() already prints an error
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Let MODULE_LICENCE match the SPDX header which is correctly based on the
previous textual description.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add code to handle IS_S_RX_FIFO_FULL_SHIFT interrupt to support
master write request with >= 64 bytes.
Iproc has a slave rx fifo size of 64 bytes.
Rx fifo full interrupt (IS_S_RX_FIFO_FULL_SHIFT) will be generated
when RX fifo becomes full. This can happen if master issues write
request of more than 64 bytes.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle single or multi byte master read request with or without
repeated start.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Update slave isr mask (ISR_MASK_SLAVE) to include remaining
two slave interrupts.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle only slave interrupts which are enabled.
The IS_OFFSET register contains the interrupt status bits which will be
set regardless of the enabling of the corresponding interrupt condition.
One must therefore look at both IS_OFFSET and IE_OFFSET to determine
whether an interrupt condition is set and enabled.
Fixes: c245d94ed1 ("i2c: iproc: Add multi byte read-write support for slave mode")
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Handle Master aborted error by flushing tx and rx fifo
and reinitializing the hw.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
V3U creates spurious interrupts which we need to handle. This costs time
until BUS_PHASE_DATA can be activated which is problematic for Gen2 SoCs
and earlier. Because of this we introduce two interrupt handlers here
which will call a generic main irq function once the timing critical
stuff is done.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Ensure this irq runs as fast as possible.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
'flags' and 'io' are needed first, so they should be at the beginning of
the private struct.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
To avoid the HW race condition on R-Car Gen2 and earlier, we need to
write to ICMCR as soon as possible in the interrupt handler. We can
improve this by writing a static value instead of masking out bits.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Store DMA mapping data in geni_i2c_dev struct to enhance DMA mapping
data scope. For example during shutdown callback to unmap DMA mapping,
this stored DMA mapping data can be used to call geni_se_tx_dma_unprep
and geni_se_rx_dma_unprep functions.
Add two helper functions geni_i2c_rx_msg_cleanup and
geni_i2c_tx_msg_cleanup to unwrap the things after rx/tx FIFO/DMA
transfers, so that the same can be used in geni_i2c_stop_xfer()
function during shutdown callback.
Signed-off-by: Roja Rani Yarubandi <rojay@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_device_unregister() is NULL-aware and thus doesn't required a
duplication check in i801_del_mux(). Besides that it's also error pointer
aware, and we may drop unneeded assignment in i801_add_mux() followed by
conversion to PTR_ERR_OR_ZERO() for the returned value.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since gpiod_remove_lookup_table() is NULL-aware, no need to have this check
in the caller. Drop duplicate NULL check.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 2000 usec to 400
usec. It greatly improves performance of I2C transactions.
Reliability of setting polling time to 400 usec has been thoroughly
validated across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With the apdma remove hand-shake signal, it requirs special
operation timing to reset i2c manually, otherwise the interrupt
will not be triggered, i2c transmission will be timeout.
Fixes: 8426fe70cfa4("i2c: mediatek: Add apdma sync in i2c driver")
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
gpiod_add_lookup_table() expects the gpiod_lookup_table->table passed to
it to be terminated with a zero-ed out entry.
So we need to allocate one more entry then we will use.
Fixes: d308dfbf62 ("i2c: mux/i801: Switch to use descriptor passing")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If the i2c device SCL bus being pulled up due to some exception before
message transfer done, the system cannot receive the completing interrupt
signal any more, it would not exit waiting loop until MAX_SCHEDULE_TIMEOUT
jiffies eclipse, that would make the system seemed hang up. To avoid that
happen, this patch adds a specific timeout for message transfer.
Fixes: 8b9ec07198 ("i2c: Add Spreadtrum I2C controller driver")
Signed-off-by: Linhua Xu <linhua.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
[wsa: changed errno to ETIMEDOUT]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----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=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
* pm-sleep:
PM: sleep: Add dev_wakeup_path() helper
PM / suspend: fix kernel-doc markup
PM: sleep: Print driver flags for all devices during suspend/resume
* pm-acpi:
PM: ACPI: Refresh wakeup device power configuration every time
PM: ACPI: PCI: Drop acpi_pm_set_bridge_wakeup()
PM: ACPI: reboot: Use S5 for reboot
* pm-domains:
PM: domains: create debugfs nodes when adding power domains
PM: domains: replace -ENOTSUPP with -EOPNOTSUPP
* powercap:
powercap: Adjust printing the constraint name with new line
powercap: RAPL: Add AMD Fam19h RAPL support
powercap: Add AMD Fam17h RAPL support
powercap/intel_rapl_msr: Convert rapl_msr_priv into pointer
x86/msr-index: sort AMD RAPL MSRs by address
For the sake of consistency add leading 0 to first register offsets
to make them all of the same width.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently header file uses partially BIT() and GENMASK() macros.
Switch it to use those macros in all cases where it's applicable
for the sake of consistency.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Starting with
commit 75820314de ("i2c: core: add generic I2C GPIO recovery")
GPIO bus recovery is supported by the I2C core, so we can remove the
driver implementation and use that one instead.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a driver tries to send an I2C message while the adapter is
suspended, this typically fails with:
i2c-sh_mobile e60b0000.i2c: Transfer request timed out
Avoid accessing the adapter while it is suspended by marking it
suspended during suspend. This allows the I2C core to catch this, and
print a warning:
WARNING: CPU: 1 PID: 13 at drivers/i2c/i2c-core.h:54
__i2c_transfer+0x4a4/0x4e4
i2c i2c-6: Transfer while suspended
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add S500 variant to the list of devices supported by the Actions Semi
Owl I2C driver.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
devm_ioremap and ioremap may return NULL which cannot be checked
by IS_ERR.
Signed-off-by: Wang Xiaojun <wangxiaojun11@huawei.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If this is not enabled, the interfaces used in this driver do not work:
drivers/i2c/busses/i2c-mlxbf.c:1888:3: error: implicit declaration of function 'i2c_slave_event' [-Werror,-Wimplicit-function-declaration]
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1888:26: error: use of undeclared identifier 'I2C_SLAVE_WRITE_REQUESTED'
i2c_slave_event(slave, I2C_SLAVE_WRITE_REQUESTED, &value);
^
drivers/i2c/busses/i2c-mlxbf.c:1890:32: error: use of undeclared identifier 'I2C_SLAVE_WRITE_RECEIVED'
ret = i2c_slave_event(slave, I2C_SLAVE_WRITE_RECEIVED,
^
drivers/i2c/busses/i2c-mlxbf.c:1892:26: error: use of undeclared identifier 'I2C_SLAVE_STOP'
i2c_slave_event(slave, I2C_SLAVE_STOP, &value);
^
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Expand the driver to support I2C_SMBUS_BLOCK_PROC_CALL since
HW supports it already.
Co-developed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mario Alejandro Posso Escobar <mario.posso.escobar@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()"), platform_get_irq() will call dev_err() on an error.
In case of i2c ocores this leads to a false-positive error being logged:
[ 4.173989] 007: ocores-i2c ocores-i2c: IRQ index 0 not found
i2c ocores already handles the case when the IRQ cannot be found and
therefore there is no benefit in having this error message being logged.
This commit switches to platform_get_irq_optional(), which does not log
in case the IRQ cannot be found.
Signed-off-by: Stefan Lässer <stefan.laesser@omicronenergy.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A combination of recent bug fixes by Doug Anderson and the proper
definition of iommu streams means that this hack is no longer needed.
Let's clean up the code by reverting '127068abe85b ("i2c: qcom-geni:
Disable DMA processing on the Lenovo Yoga C630")'.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Caleb Connolly <caleb@connolly.tech>
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c-mxs driver only runs on DT-platform and there is no
need to use the platform_device_id structure to pass the driver
data.
Get rid of it to make the code simpler.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
io_base and io_size are assigned to only in .probe() and otherwise unused.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
After the commit c5eb119007 ("PCI / PM: Allow runtime PM without callback
functions") we no more need empty stubs for runtime-pm to work.
The driver has no device specific task(s) for .suspend() . The stub was
placed just for runtime-pm, which can be dropped now.
Reported-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This adds i2c bus recovery to the mv64xxx driver.
Implement bus recovery to recover from SCL/SDA stuck low.
This uses the generic recovery function, setting the clock/data lines as
GPIO pins, and sending 9 clocks to try and recover the bus.
Signed-off-by: Mark Tomlinson <mark.tomlinson@alliedtelesis.co.nz>
[wsa: added some curly braces]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If arbitration is lost, the master automatically changes to slave mode.
I2SR_IBB may or may not be reset by hardware. Raising a STOP condition
by resetting I2CR_MSTA has no effect and will not clear I2SR_IBB.
So calling i2c_imx_bus_busy() is not required and would busy-wait until
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org # Requires trivial backporting, simple remove
# the 3rd argument from the calls to
# i2c_imx_bus_busy().
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Arbitration Lost (IAL) can happen after every single byte transfer. If
arbitration is lost, the I2C hardware will autonomously switch from
master mode to slave. If a transfer is not aborted in this state,
consecutive transfers will not be executed by the hardware and will
timeout.
Signed-off-by: Christian Eggers <ceggers@arri.de>
Tested (not extensively) on Vybrid VF500 (Toradex VF50):
Tested-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
According to the "VFxxx Controller Reference Manual" (and the comment
block starting at line 97), Vybrid requires writing a one for clearing
an interrupt flag. Syncing the method for clearing I2SR_IIF in
i2c_imx_isr().
Signed-off-by: Christian Eggers <ceggers@arri.de>
Fixes: 4b775022f6 ("i2c: imx: add struct to hold more configurable quirks")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During cci_isr() errors read from register fields belonging to
i2c master1 are currently assigned to the status field belonging to
i2c master0. This patch corrects this error, and always assigns
master1 errors to the status field of master1.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Reported-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add dev_wakeup_path() helper to avoid to spread
dev->power.wakeup_path test in drivers.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Sometimes we would get the following flow when doing an i2cset:
0x1 STATUS SLAVE_ACTIVITY=0x1 : RAW_INTR_STAT=0x514 : INTR_STAT=0x4
I2C_SLAVE_WRITE_RECEIVED
0x1 STATUS SLAVE_ACTIVITY=0x0 : RAW_INTR_STAT=0x714 : INTR_STAT=0x204
I2C_SLAVE_WRITE_REQUESTED
I2C_SLAVE_WRITE_RECEIVED
Documentation/i2c/slave-interface.rst says that I2C_SLAVE_WRITE_REQUESTED,
which is mandatory, should be sent while the data did not arrive yet. It
means in a write-request I2C_SLAVE_WRITE_REQUESTED should be reported
before any I2C_SLAVE_WRITE_RECEIVED.
By the way, I2C_SLAVE_STOP didn't be reported in the above case because
DW_IC_INTR_STAT was not 0x200.
dev->status can be used to record the current state, especially Designware
I2C controller has no interrupts to identify a write-request. This patch
makes not only I2C_SLAVE_WRITE_REQUESTED been reported first when
IC_INTR_RX_FULL is rising and dev->status isn't STATUS_WRITE_IN_PROGRESS
but also I2C_SLAVE_STOP been reported when a STOP condition is received.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If some bits were cleared by i2c_dw_read_clear_intrbits_slave() in
i2c_dw_isr_slave() and not handled immediately, those cleared bits would
not be shown again by later i2c_dw_read_clear_intrbits_slave(). They
therefore were forgotten to be handled.
i2c_dw_read_clear_intrbits_slave() should be called once in an ISR and take
its returned state for all later handlings.
Signed-off-by: Michael Wu <michael.wu@vatics.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The Mellanox BlueField I2C controller is only present on Mellanox
BlueField SoCs. Hence add a dependency on MELLANOX_PLATFORM, to prevent
asking the user about this driver when configuring a kernel without
Mellanox platform support.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the email addresses of the author and the maintainer
of the Mellanox BlueField I2C driver.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reference clock frequency remains the same across Bluefield
products. Thus, update the frequency and rename the macro.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Few wrapper functions are useless and can be inlined. So
delete mlxbf_i2c_read() and mlxbf_i2c_write() and replace
them with readl() and writel(), respectively. Also delete
mlxbf_i2c_read_data() and mlxbf_i2c_write() and replace
them with ioread32be() and iowrite32be(), respectively.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The build fails with "implicit declaration of function
'acpi_device_uid'" error. Thus, protect ACPI function calls
from being called when CONFIG_ACPI is disabled.
Fixes: b5b5b32081 ("i2c: mlxbf: I2C SMBus driver for Mellanox BlueField SoC")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Khalil Blaiech <kblaiech@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Implements atomic transfers to fix reboot/shutdown on r8a7790 Lager and
similar boards.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
[wsa: some whitespace fixing]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq never returns 0. Don't check for this. Make it clear that
the error path always returns a negative error code.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If platform_get_irq returns an error, relay this error to the caller of
the probe function. Don't change all errors to -EINVAL. This breaks the
case where platform_get_irq returns -EPROBE_DEFER.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_irq already prints an error message if the requested irq
was not found. Don't print another message in the driver.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The i2c driver default do dma reset after i2c reset, but sometimes
i2c reset will trigger dma tx2rx, then apdma write data to dram
which has been i2c_put_dma_safe_msg_buf(kfree). Move dma reset
before i2c reset in mtk_i2c_init_hw to fix it.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The FU540-C000 has a broken IRQ and support was added earlier
so that it will operate in polling mode, but seems to work only
in case interrupts property is missing from the i2c0 dt-node.
This should not be the case and the driver should handle polling
mode with the interrupt property present in i2c0 node of the
device tree.
So check if it's the FU540-C000 soc and enable polling mode master
xfers, as the IRQ for this chip is broken.
Fixes commit c45d4ba867 ("i2c: ocores: add polling mode workaround
for Sifive FU540-C000 SoC")
Signed-off-by: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Acked-by: Peter Korsgaard <peter@korsgaard.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
