Export contents of struct mips_fpu_emulator_stats via debugfs.
There is no way to read these statistics for now but they (at least
the "emulated" count) might be sometimes useful for performance tuning
on FPU-less CPUs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently a number of unaligned instructions is counted but not used.
Add /debug/mips/unaligned_instructions file to show the value.
And add /debug/mips/unaligned_action to control behavior upon an
unaligned access. Possible actions are:
0: silently fixup the unaligned access.
1: send SIGBUS.
2: dump registers, process name, etc. and fixup.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Fix pci ops for secondary PCIC
* Do not reserve 1MB for PCI MEM region (leave PCIBIOS_MIN_MEM zero)
* Use platform_device to provide ethernet addresses for internal NICs.
(background: TX49XX SoCs include PCI NIC (TC35815 compatible)
connected via its internal PCI bus, but the NIC's PROM interface is
not connected to SEEPROM. So we must provide its ethernet address
by another way.)
* Check return value of early_read_config_word()
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39XX and TX49XX have "reserved" segment in CKSEG3 area.
0xff000000-0xff3fffff on TX49XX and 0xff000000-0xfffeffff on TX39XX
are reserved (unmapped, uncached). Controllers on these SoCs are
placed in this segment.
This patch add plat_ioremap() and plat_iounmap() to override default
behavior and implement these hooks for TX39/TX49.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use rtc-rs5c348 and at25 spi protocol driver and spi_txx9 spi
controller driver instead of platform dependent codes.
This patch also removes dependencies to old RTC interfaces such as
rtc_mips_get_time, etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
GPIO 0..15 are for TX4938 PIO pins, GPIO 16..18 are for FPGA-driven
chipselect signals for SPI devices.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- use RTC_CLASS instead of GEN_RTC
- get rid of ds1216 in favour of a RTC_CLASS driver
- use correct console device for older RM400
- use physical addresses for 82596 device
- use 128 byte L1 cache line size (this is needed because most of the
SNI caches are using 128 L2 cache lines)
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add default configuration for the PMC-Sierra
MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add PCI support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add mips common support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patch to add core platform support for the PMC-Sierra MSP71xx devices.
Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Which will cut down the cost of RDHWR $29 which is used to obtain the
TLS pointer and so far being emulated in software down to a single cycle
operation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to break the code of people who think they are supposed to scribble
into the pci device structure - it's off limits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is an optimised implementation of early printk() for the DECstation.
After the recent conversion to a MIPS-specific generic routine using a
character-by-character output the performance dropped significantly.
This change reverts to the previous speed -- even at 9600 bps of the
serial console the difference is visible with a naked eye; I presume for a
framebuffer it is even worse (it may depend on exactly which one is used
though).
Additionally the change includes a fix for a problem that the old
implementation had -- the format used would not actually limit the length
of the string output. This new implementation uses a local buffer to deal
with it -- even with this additional copying it is much faster than the
generic function.
Plus this driver is registered much earlier than the generic one,
allowing one to see critical messages, such as one about an incorrect CPU
setting used, that are produced beforehand. :-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are no I/O ports on the DECstation whatsoever in any configuration
as neither the CPU nor the peripheral buses used have a concept of such.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable Cobalt button support and change ATA driver from BLK_DEV_VIA82CXXX
to PATA_VIA..
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert old/obsolete NORET_TYPE and ATTRIB_NORET macros to use the
newer standard of "__noreturn" as defined in compiler-gcc.h.
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the generic GPIO API to Au1x00 boards. It requires
the generic GPIO patch for MIPS boards by Yoichi Yuasa. Now there is a MIPS
target using it, can you queue these patchset for 2.6.22 ? Thank you very
much in advance.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use standard missing-syscalls with EXTRA_CFLAGS instead of duplicating
the command. And move the archprepare rule before the archclean rule.
Suggested by Franck Bui-Huu. Also add "echo" to show the target ABI.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
sched-cfs-v2.6.22-git-v18.patch introduces CPU_IDLE in sched.h.
This conflict with the already existing define in
include/asm-s390/processor.h
Just rename the s390 defines, since they will go away as soon as
we support CONFIG_NO_HZ instead of our own CONFIG_NO_IDLE_HZ.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After the in-kernel system call has been remove the system call path
can be optimized. The problem state bit of the old psw is always set
between system_call and sysc_do_svc. SAVE_ALL_SVC uses this information
to avoid two instructions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The bogomips calculation triggered via reading from /proc/cpuinfo
can return incorrect values if the qrnnd assembly is called with a
pointer in %r2 with any of the upper 32 bits set.
Fix this by using 64 bit division / remainder operation provided by
gcc instead of calling the assembly.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Merge smp_count_cpus() and smp_get_save_areas() so we save a loop over
all potentially present cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Check if a command is available before executing. Saves some
superfluous service calls that won't succeed anyway.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce some new interfaces so that random subsystems don't have to
mess around with sclp internal structures.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
SDM says that brl instruction must be followed by a stop bit.
Fix instance in BRL_COND_FSYS_BUBBLE_DOWN where it isn't.
Signed-off-by: Christian Kandeler <christian.kandeler@hob.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On SN systems, when setting the IORESOURCE_ROM_BIOS_COPY resource flag,
the resource length should be set to the actual size of the ROM image
so that a call to pci_map_rom() returns the correct size.
Signed-off-by: John Keller <jpk@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
It's not a good idea to use "ssm psr.ic | psr.i" to simultaneously
enable interrupts and interrupt state collection, the two bits can
take effect asynchronously, so it is possible for an interrupt to
be serviced while psr.ic is still zero.
Signed-off-by: Tony Luck <tony.luck@intel.com>
track TSC-unstable events and propagate it to the scheduler code.
Also allow sched_clock() to be used when the TSC is unstable,
the rq_clock() wrapper creates a reliable clock out of it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
the SMP load-balancer uses the boot-time migration-cost estimation
code to attempt to improve the quality of balancing. The reason for
this code is that the discrete priority queues do not preserve
the order of scheduling accurately, so the load-balancer skips
tasks that were running on a CPU 'recently'.
this code is fundamental fragile: the boot-time migration cost detector
doesnt really work on systems that had large L3 caches, it caused boot
delays on large systems and the whole cache-hot concept made the
balancing code pretty undeterministic as well.
(and hey, i wrote most of it, so i can say it out loud that it sucks ;-)
under CFS the same purpose of cache affinity can be achieved without
any special cache-hot special-case: tasks are sorted in the 'timeline'
tree and the SMP balancer picks tasks from the left side of the
tree, thus the most cache-cold task is balanced automatically.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The printk level in this printk is bogus, as the previous printk
didn't have a terminating \n resulting in ..
Intel E7520/7320/7525 detected.<6>Disabling irq balancing and affinity
It also never printed a \n at all in the case where we didn't do
the quirk.
Change it to only make noise if it actually does something useful.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Writing to MSR 0x51400017 forces a hard reset on CS5536-based machines,
this has the reboot fixup do just that if such a board is detected.
Acked-by: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o Commit 1833d6bc72 broke the build if
compiled with CONFIG_ES7000=y and CONFIG_X86_GENERICARCH=n
arch/i386/kernel/built-in.o(.init.text+0x4fa9): In function `acpi_parse_madt':
: undefined reference to `acpi_madt_oem_check'
arch/i386/kernel/built-in.o(.init.text+0x7406): In function `smp_read_mpc':
: undefined reference to `mps_oem_check'
arch/i386/kernel/built-in.o(.init.text+0x8990): In function
`connect_bsp_APIC':
: undefined reference to `enable_apic_mode'
make: *** [.tmp_vmlinux1] Error 1
o Fix the build issue. Provided the definitions of missing functions.
o Don't have ES7000 machine. Only compile tested.
Cc: Len Brown <lenb@kernel.org>
Cc: Natalie Protasevich <protasnb@gmail.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Processors synchronization in set_mtrr requires the .gate field to be set
after .count field is properly initialized. Without an explicit barrier,
the compiler was reordering those memory stores. That was sometimes
causing a processor (in ipi_handler) to see the .gate change and decrement
.count before the latter is set by set_mtrr() (which then hangs in a
infinite loop with irqs disabled).
Signed-off-by: Loic Prylli <loic@myri.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit 635cf99a80 introduced a
regression. Executing a ptrace single step after certain int80
accesses will infinitely loop and never advance the PC.
The TIF_SINGLESTEP check should be done on the return from the syscall
and not before it.
I loops on each single step on the pop right after the int80 which writes out
to the console. At that point you can issue as many single steps as you want
and it will not advance any further.
The test case is below:
/* Test whether singlestep through an int80 syscall works.
*/
#define _GNU_SOURCE
#include <stdio.h>
#include <unistd.h>
#include <fcntl.h>
#include <sys/ptrace.h>
#include <sys/wait.h>
#include <sys/mman.h>
#include <asm/user.h>
#include <string.h>
static int child, status;
static struct user_regs_struct regs;
static void do_child()
{
char str[80] = "child: int80 test\n";
ptrace(PTRACE_TRACEME, 0, 0, 0);
kill(getpid(), SIGUSR1);
write(fileno(stdout),str,strlen(str));
asm ("int $0x80" : : "a" (20)); /* getpid */
}
static void do_parent()
{
unsigned long eip, expected = 0;
again:
waitpid(child, &status, 0);
if (WIFEXITED(status) || WIFSIGNALED(status))
return;
if (WIFSTOPPED(status)) {
ptrace(PTRACE_GETREGS, child, 0, ®s);
eip = regs.eip;
if (expected)
fprintf(stderr, "child stop @ %08lx, expected %08lx %s\n",
eip, expected,
eip == expected ? "" : " <== ERROR");
if (*(unsigned short *)eip == 0x80cd) {
fprintf(stderr, "int 0x80 at %08x\n", (unsigned int)eip);
expected = eip + 2;
} else
expected = 0;
ptrace(PTRACE_SINGLESTEP, child, NULL, NULL);
}
goto again;
}
int main(int argc, char * const argv[])
{
child = fork();
if (child)
do_parent();
else
do_child();
return 0;
}
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: <stable@kernel.org>
Cc: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The idle loop goes to sleep using the WAIT instruction if !need_resched().
This has is suffering from from a race condition that if if just after
need_resched has returned 0 an interrupt might set TIF_NEED_RESCHED but
we've just completed the test so go to sleep anyway. This would be
trivial to fix by just disabling interrupts during that sequence as in:
local_irq_disable();
if (!need_resched())
__asm__("wait");
local_irq_enable();
but the processor architecture leaves it undefined if a processor calling
WAIT with interrupts disabled will ever restart its pipeline and indeed
some processors have made use of the freedom provided by the architecture
definition. This has been resolved and the Config7.WII bit indicates that
the use of WAIT is safe on 24K, 24KE and 34K cores. It also is safe on
74K starting revision 2.1.0 so enable the use of WAIT with interrupts
disabled for 74K based on a c0_prid of at least that.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported by Eugene Surovegin <ebs@ebshome.net>.
If only modules were users of these functions they did not get linked into
the kernel proper, so later module loads would fail as well.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
C0_status doesn't need to be initialized at this point anyway; the register
will be initialized later.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] always allow dump_stack() to produce a backtrace
[ARM] Fix non-page aligned boot time mappings
[ARM] 4458/1: pxa: Fix CKEN usage and hence fix pxa suspend/resume
[ARM] 4454/1: Use word accesses in Versatile PCI config reads
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Update defconfigs
[POWERPC] Uninline and export virq_to_hw() for the pasemi_mac driver
[POWERPC] Fix PMI breakage in cbe_cbufreq driver
[POWERPC] Disable old EMAC driver in arch/powerpc
Don't make this dependent on CONFIG_DEBUG_KERNEL - if we hit a WARN_ON
we need the stack trace to work out how we got to that point.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
AT91SAM9260 stopped booting with the recent changes to MM
initialisation - it was asking for a non-aligned virtual address
which caused loops to be non-terminal. Fix this by rounding
virtual addresses down, but remember to include the offset in
the length, and round the length up to the following page.
This means that asking for a mapping of 4K starting at 2K into
a page maps two pages as one would expect.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When Andi reverted the HPET resource reservation (in commit
0f8dc2f065), he didn't remove the now
unused variables, which just causes gcc to be noisy.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this change it works again when the nmi watchdog is disabled.
Signed-off-by: Andi Kleen <ak@suse.de>
Cc: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Matthias Lenk reports that the PCI subsystem would move the HPET on
SB400/SB600-based systems, where the HPET is in BAR1 of the SMbus
controller.
The reason? The ACPI layer registered the PCI MMIO range as being busy
too early, before PCI enumeration had happened, causing the PCI layer to
decide that it should relocate the resources somewhere else.
Firmware resources should be marked busy _after_ the PCI enumeration and
probing has happened, not before.
Remove the too-early reservation, we'll fix it up to do it properly
later. In the meantime, this solves the regression.
Tested-by: Matthias Lenk <matthias.lenk@amd.com>
Cc: Aaron Durbin <adurbin@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PXA CKEN changes broken syspend/resume on the pxa27x. This patch
corrects the problem and fixes another couple of bad references.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ARM Versatile PCI config reads of one byte width have the lowest two
bits of the address cleared and result in reading from a wrong place
in the config space. This change is to use word size accesses like it is done for halfword reads.
Byte reads are used for retrieving the IRQ number of a PCI device and the problem was not exposed until 2.6.20 because the value read was discarded in drivers/pci/setup-irq.c (recently fixed).
Signed-off-by: Andrzej Zaborowski <andrew@openedhand.com>
Acked-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Uninline virq_to_hw and export it so modules can use it. The alternative
would be to export the irq_map array instead, but it's an infrequently
called function, and keeping the array unexported seems considerably
cleaner.
This is needed so that the pasemi_mac driver can be compiled as a module.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The recent change to cell_defconfig to enable cpufreq on Cell exposed
the fact that the cbe_cpufreq driver currently needs the PMI interface
code to compile, but Kconfig doesn't make sure that the PMI interface
code gets built if cbe_cpufreq is enabled.
In fact cbe_cpufreq can work without PMI, so this ifdefs out the code
that deals with PMI. This is a minimal solution for 2.6.22; a more
comprehensive solution will be merged for 2.6.23.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 52ade9b3b9 changed the suspend code
ordering to execute pm_ops->prepare() after the device model per-device
.suspend() calls in order to fix some ACPI-related issues. Unfortunately, it
broke the at91 platform which assumed that pm_ops->prepare() would be called
before suspending devices.
at91 used pm_ops->prepare() to get notified of the target system sleep state,
so that it could use this information while suspending devices. However, with
the current suspend code ordering pm_ops->prepare() is called too late for
this purpose. Thus, at91 needs an additional method in 'struct pm_ops' that
will be used for notifying the platform of the target system sleep state.
Moreover, in the future such a method will also be needed by ACPI.
This patch adds the .set_target() method to 'struct pm_ops' and makes the
suspend code call it, if implemented, before executing the device model
per-device .suspend() calls. It also modifies the at91 code to use
pm_ops->set_target() instead of pm_ops->prepare().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 3ebad59056 ("[PATCH] x86: Save and
restore the fixed-range MTRRs of the BSP when suspending") added mtrr
operations without verifying that the CPU has MTRRs. Crashes transmeta
CPUs.
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: <linux@horizon.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 9215da3320 "fixed" the MTRR range
check to not allow any MTRR's under the 1MB mark (since that's where the
fixed MTRR's are active).
However, that was totally bogus, since it's normal (and almost required)
to have a large variable MTRR that starts at 0, and covers some large
percentage of the whole RAM, and then using the fixed MTRR's to override
that large MTRR to handle the special ISA hole in the 640k-1M region.
The old check was bogus too (checking that no variable MTRR is used that
is entirely under the 1MB range), but at least it wasn't actively
detrimental, because no sane situation would ever trigger such MTRR
usage in the first place.
That said, the whole notion of not allowing variable MTRR's in the low
1MB is just stupid, so rather than revert the commit, this just removes
the whole sad and unnecessary check entirely.
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Tested-by: Luca Palermo <darkmage@sabayonlinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Add linux/pagemap.h to asm/tlb.h
[SPARC64]: Need to set state to IDLE during sun4v IRQ enable.
[SPARC64]: Fix VIRQ enabling.
[SPARC64]: Add irqs to mdesc_node.
The vdso64 portion of patch 74609f4536 for
fixing problems with NULL gettimeofday input mistakenly checks for a
null tz field twice, when it should be checking for null tz once, and
null tv once; by way of a r10/r11 typo.
Any application calling gettimeofday(&tv,NULL) will "fail".
This corrects that typo, and makes my G5 happy.
Tested on G5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Tony Breeds <tony@bakeyournoodle.com>
Forwarded-by: Ben Herrenschmidt <benh@kernel.crashing.org>
[ Ben says: "I checked the 32 bits part of the change is correct. You
can probably blame me for originally writing the 2 versions with
inversed usage of r10 and r11, thus confusing Tony :-)"
Ben duly blamed. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not all the world is an i386. Many architectures need 64-bit arguments to be
aligned in suitable pairs of registers, and the original
sys_sync_file_range(int, loff_t, loff_t, int) was therefore wasting an
argument register for padding after the first integer. Since we don't
normally have more than 6 arguments for system calls, that left no room for
the final argument on some architectures.
Fix this by introducing sys_sync_file_range2(int, int, loff_t, loff_t) which
all fits nicely. In fact, ARM already had that, but called it
sys_arm_sync_file_range. Move it to fs/sync.c and rename it, then implement
the needed compatibility routine. And stop the missing syscall check from
bitching about the absence of sys_sync_file_range() if we've implemented
sys_sync_file_range2() instead.
Tested on PPC32 and with 32-bit and 64-bit userspace on PPC64.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Make SN2 PCI code use ioremap rather than manually mangle the address
[IA64] Force error to surface in nofault code
[IA64] change sh_change_coherence oemcall to use nolock
[IA64] remove duplicate header include line
[IA64] Correct unwind validation code
[IA64] is_power_of_2-ia64/mm/hugetlbpage.c
Force irq migration path during cpu offline, is not using proper locks and
irq_chip mask/unmask routines. This will result in some races(especially
the device generating the interrupt can see some inconsistent state,
resulting in issues like stuck irq,..).
Appended patch fixes the issue by taking proper lock and encapsulating
irq_chip set_affinity() with a mask() before and an unmask() after.
This fixes a MSI irq stuck issue reported by Darrick Wong.
There are several more general bugs in this area(irq migration in the
process context). For example,
1. Possibility of missing edge triggered irq.
2. Reliable method of migrating level triggered irq in the process context.
We plan to look and close these in the near future.
Eric says:
In addition even with the fix from Suresh there is still at least one
nasty hardware race in fixup_irqs(). However we exercise that code
path rarely enough that we are unlikely to hit it in the real world,
and that race seems to have existed since the code was merged. And a
fix for that is not coming soon as it is an open investigation area
if we can fix irq migration to work outside of irq context or if
we have to rework the requirements imposed by the generic cpu hotplug
and layer on fixup_irqs(). So this may come up again.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Reported-and-tested-by: Darrick Wong <djwong@us.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
set the irq_chip name for lapic.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 4449/1: more entries in arch/arm/boot/.gitignore
[ARM] 4452/1: Force the literal pool dump before reloc_end
[ARM] Update show_regs/oops register format
[ARM] Add support for pause_on_oops and display preempt/smp options
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Count timer interrupts correctly.
[MIPS] SMTC and non-SMTC kernel and modules are incompatible
[MIPS] EMMA2RH: Disable GEN_RTC, it can't possibly work.
[MIPS] Remove a duplicated local variable in test_and_clear_bit()
[MIPS] use compat_siginfo in rt_sigframe_n32
[MIPS] 20K: Handle WAIT related bugs according to errata information
[MIPS] AP/SP requires shadow registers, auto enable support.
[MIPS] Fix pb1500 reg B access
[MIPS] Alchemy: Fix wrong cast
[MIPS] remove "support for" from system type entry
[MIPS] add io_map_base to pci_controller on Cobalt
[MIPS] __ucmpdi2 arguments are unsigned long long.
This one changes the SN2 specific PCI drivers to use ioremap() for
obtaining the real address to access for the PCI registers instead of
manually calculating them with __IA64_UNCACHED_OFFSET.
The patch should have no real change when running on a normal Linux
kernel, but when running as a paravirtualized it is needed.
Signed-off-by: Jes Sorenson <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Montecito behaves slightly differently than previous processors,
resulting in the MCA due to a failed PIO read to sometimes surfacing
outside the nofault code. Adding an additional or and stop bits
ensures the MCA surfaces in the nofault code.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Remove duplicate header include line from arch/ia64/kernel/time.c.
Signed-off-by: MUNEDA Takahiro <muneda.takahiro@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Both rp_loc and pfs_loc can be in the register stack area _or_ they can
be in the memory stack area, the latter occurs when a struct pt_regs is
pushed. Correct the validation check on these fields to check for both
stack areas. Not allowing for memory stack locations means no
backtrace past ia64_leave_kernel, or any other code that uses
PT_REGS_UNWIND_INFO.
Signed-off-by: Keith Owens <kaos@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Replacing (n & (n-1)) in the context of power of 2 checks
with is_power_of_2
Signed-off-by: vignesh babu <vignesh.babu@wipro.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Neither rtc_mips_get_time nor rtc_mips_set_time are being initialized by
the EMMA2RH setup code, so genrtc at best was a RTC dummy avoiding a few
error messages but not providing actual functionality.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We used to avoid the WAIT entirely on the 20K but really only need to do
this on early revs of the 20K. Without this a 20K was a bit of a
power hog. Well, in the lower power power hog category ;-)
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We were doing the wrong call to turn them on, and also
when enabling we need to forcefully set the state to IDLE.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a bug which can cause corruption of the floating-point state
on return from a signal handler. If we have a signal handler that has
used the floating-point registers, and it happens to context-switch to
another task while copying the interrupted floating-point state from the
user stack into the thread struct (e.g. because of a page fault, or
because it gets preempted), the context switch code will think that the
FP registers contain valid FP state that needs to be copied into the
thread_struct, and will thus overwrite the values that the signal return
code has put into the thread_struct.
This can occur because we clear the MSR bits that indicate the presence
of valid FP state after copying the state into the thread_struct. To fix
this we just move the clearing of the MSR bits to before the copy. A
similar potential problem also occurs with the Altivec state, and this
fixes that in the same way.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Consider the prototype for gettimeofday():
int gettimofday(struct timeval *tv, struct timezone *tz);
Although it is valid to call with /either/ tv or tz being NULL, and
the C version of sys_gettimeofday() supports this, the current version
of gettimeofday() in the VDSO will SEGV if called with a NULL tv.
This adds a check for tv being NULL so that it doesn't SEGV.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update the g5_defconfig with default settings.
This is to keep things up to date, and specifically to ensure that the
CONFIG_MACINTOSH_DRIVERS option is enabled. This also turns on
CONFIG_MSI.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
cc: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
In the arch/arm/boot/compressed/head.S file, the contents of the
literal pool accumulated during the relocatable code must be dumped
before reloc_end.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add silicon revision "any" and "none". Add proper -mcpu option according
to the cpu and silicon revision configuration.
Need update to use latest Blackfin cross compile toolchain.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Register %ebx serves as the "global offset table base register" for
position-independent code. For absolute code, %ebx serves as a local
register and has no specified role in the function calling sequence. In
either case, a function must preserve the register value for the caller.
acpi_copy_wakeup_routine overrides %ebx without saving it, this may corrupt
the called data.
Kevin found that most time the value of Sx is saved in %esi, however
sometimes compiler also uses %ebx. When this happens, suspends fails since
sleep value in ebx is changed by acpi_copy_wakeup_routine.
The same funtion in X86_64 doesn't have this problem.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Looks-okay-to: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <lenb@kernel.org>
Acked-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Background:
When a userspace application wants to know about machine check events, it
opens /dev/mcelog and does a read(). Usually, we found that this interface
works well, but in some cases, when the system was taking large numbers of
machine check exceptions, the read() would hang. The system would output a
soft-lockup warning, and the daemon reading from /dev/mcelog would suck up
as much of a single CPU as it could spinning in system space.
Description:
This patch fixes this bug. In particular, there was a "continue" inside a
timeout loop that presumably was intended to break out of the outer loop,
but instead caused the inner loop to continue. This patch also makes the
condition for the break-out a little more evident by changing a
!time_before to a time_after_eq.
Result:
The read() no longer hangs in this test case.
Testing:
On my system, I could replicate the bug with the following command:
# for i in `seq 15000`; do ./inject_sbe.sh; done
where inject_sbe.sh contains commands to inject a single-bit error into the
next memory write transaction.
Patch:
This patch is against git f1518a088b.
Signed-off-by: Joshua Wise <jwise@google.com>
Signed-off-by: Tim Hockin <thockin@google.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hopefully this fixes http://bugzilla.kernel.org/show_bug.cgi?id=8635
The struct in6_addr passed to csum_ipv6_magic() is 4 byte aligned, so we
can't use the regular 64-bit loads. Since the cost of handling of 4 byte
and 1 byte aligned 64-bit data is roughly the same, this code can cope with
any src/dst [mis]alignment.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Dustin Marquess <jailbird@alcatraz.fdf.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update defconfigs for ATNGW100 and ATSTK1002. This will enable the
SLUB allocator by default on both, and will enable NFS root on
ATSTK1002 (ATNGW100 had it enabled before.)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
The current at32ap7000 platform devices aren't declared as supporting DMA,
so that layered drivers can't tell whether they need to manage DMA.
This patch makes all those platform devices report that they support DMA.
Most do, but in a few cases this is inappropriate.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
USART mapping used to be accomplished by the manual filling of
at32_usart_map[] and at32_nr_usarts. This has now been replaced
with at32_map_usart() so we can remove these variables.
Signed-off-by: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
If (start + size) is not cacheline aligned and (start & mask) > (end &
mask), the last but one cacheline won't be invalidated as it should.
Fix this by rounding `end' down to the nearest cacheline boundary if
it gets adjusted due to misalignment.
Also flush the write buffer unconditionally -- if the dcache wrote
back a line just before we invalidated it, the dirty data may be
sitting in the write buffer waiting to corrupt our buffer later.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Previously a program could switch to a compat mode segment and then
execute SYSCALL and it would jump to an uninitialized MSR and crash
the kernel.
Instead supply a dummy target for this case.
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is only used for PAE kernels in set_64bit.
The problem is that due to a old Windows bug many CPUs need magic MSRs
to enable CMPXCHG64, and we can't do that nicely early enough before
it is potentially used.
But since we only need it in PAE kernels so only force the checking
for CMPXCHG65 with PAE.
This fixes a boot failure on Transmeta Crusoe
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In previous commit I used u32 for u16 register.
This code will work only when ACPI block address is set.
For now it is only for VT8235 and VT8237.
Signed-off-by: Rafal Bilski <rafalbilski@interia.pl>
Signed-off-by: Dave Jones <davej@redhat.com>
Turns on trace earlier, so crashes at kernel start should print out a
trace, making things easier to debug.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
- Move cache initialization to C from assembly.
- Move anomaly workaround for writing [ID]MEM_CONTROL to assembly, so
that we don't have to mess around with .align directives in C source.
- Fix a bug where bfin_write_DMEM_CONTROL would write to IMEM_CONTROL
- Break out CPLB related code from kernel/setup.c into their own file.
- Don't define variables in header files, only declare them.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
SIC_IWR crosses several registers
- add missing implementations
- make sure SIC_IWR is SET after boot
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
This patch defines (and provides) entry points for certain user space functions
at fixed addresses. The Blackfin has no usable atomic instructions, but we can
ensure that these code sequences appear atomic from a user space point of view
by detecting when we're in the process of executing them during the interrupt
handler return path. This allows much more efficient pthread lock
implementations than the bfin_spinlock syscall we're currently using.
Also provided is a small sys_rt_sigreturn stub which can be used by the signal
handler setup code. The signal.c part will be committed separately.
Signed-off-by: Bernd Schmidt <bernd.schmidt@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
The ADSP-BF54x was specifically designed to meet the needs of convergent multimedia
applications where system performance and cost are essential ingredients. The
integration of multimedia, human interface, and connectivity peripherals combined
with increased system bandwidth and on-chip memory provides customers a platform to
design the most demanding applications.
Since now, ADSP-BF54x will be supported in the Linux kernel and bunch of related drivers
such as USB OTG, ATAPI, NAND flash controller, LCD framebuffer, sound, touch screen will
be submitted later.
Please enjoy the show.
Signed-off-by: Roy Huang <roy.huang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
update lists for 533, 537, and add SSYNC workaround into assembly files.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Do not mark the kernel text read only if KPROBES is in the kernel;
kprobes needs to hot-patch the kernel text to insert it's
instrumentation.
In this case, only mark the .rodata segment as read only.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: S. P. Prasanna <prasanna@in.ibm.com>
Cc: Andi Kleen <ak@suse.de>
Cc: William Cohen <wcohen@redhat.com>
Cc: Ian McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add special-case handling for "handle_interruption" so that we can rewind
past the interruption. This is useful for seeing what caused a BUG() or
WARN_ON(); otherwise the unwind stops at the interruption.
Signed-off-by: Randolph Chung <tausq@debian.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The unwinder was broken by the shift of PAGE_OFFSET in order to increase the
size of the vmalloc area on 64-bit kernels.
Signed-off-by: Randolph Chung <tausq@debian.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix powermac late initcall to only run on powermac
[POWERPC] PowerPC: Prevent data exception in kernel space (32-bit)
WARNING: arch/x86_64/kernel/built-in.o(.text+0xace9): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr')
WARNING: arch/x86_64/kernel/built-in.o(.text+0xad09): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr')
WARNING: arch/x86_64/kernel/built-in.o(.text+0xad38): Section mismatch: reference to .init.text: (between 'get_mtrr_state' and 'mtrr_wrmsr')
WARNING: drivers/built-in.o(.text+0x3a680): Section mismatch: reference to .init.text:acpi_map_pxm_to_node (between 'acpi_get_node' and 'acpi_lock_ac_dir')
AK: also marked mtrr_bp_init __init to avoid some more warnings
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Disable CLFLUSH again; it is still broken. Always do WBINVD.
- Always flush in the i386 case, not only when there are deferred pages.
These are both brute-force inefficient fixes, to be improved
next release cycle.
The changes to i386 are a little more extensive than strictly
needed (some dead code added), but it is more similar to the x86-64 version
now and the dead code will be used soon.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Right now Kprobes cannot write to the write protected kernel text when
DEBUG_RODATA is enabled. Disallow this in Kconfig for now.
Temporary fix for 2.6.22. In .23 add code to temporarily
unprotect it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not directly related to x86, but I got tired of seeing these warnings on every
kconfig update when building on a non m68k box:
drivers/input/keyboard/Kconfig:170:warning: 'select' used by config symbol 'KEYBOARD_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
drivers/input/mouse/Kconfig:182:warning: 'select' used by config symbol 'MOUSE_ATARI' refers to undefined symbol 'ATARI_KBD_CORE'
I moved the definition of ATARI_KBD_CORE into drivers/input/keyboard/Kconfig
so it's always seen by Kconfig.
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Several reports that VIA bridges don't support DAC and corrupt
data. I don't know if it's fixed, but let's just blacklist
them all for now.
It can be overwritten with iommu=usedac
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Correctly convert the u64 arguments from 32bit to 64bit.
Pointed out by Heiko Carstens.
I guess this proves Linus' theory that nobody uses the more exotic Linux
specific syscalls. It wasn't discovered by a user.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For some platforms it's definitions may conflict. So that's the one-liner.
The rest is 10 square kilometers of collateral damage fixup this include
used to paper over.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Current ppc64_defconfig kernel fails to boot on iSeries, dying with:
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc00000000071b258
Oops: Kernel access of bad area, sig: 11 [#1]
SMP NR_CPUS=32 iSeries
<snip>
NIP [c00000000071b258] .iSeries_src_init+0x34/0x64
LR [c000000000701bb4] .kernel_init+0x1fc/0x3bc
Call Trace:
[c000000007d0be30] [0000000000008000] 0x8000 (unreliable)
[c000000007d0bea0] [c000000000701bb4] .kernel_init+0x1fc/0x3bc
[c000000007d0bf90] [c0000000000262d4] .kernel_thread+0x4c/0x68
Instruction dump:
e922cba8 3880ffff 78840420 f8010010 f821ff91 60000000 e8090000 78095fe3
4182002c e922cb58 e862cbb0 e9290140 <e8090000> f8410028 7c0903a6 e9690010
Kernel panic - not syncing: Attempted to kill init!
This happens because some powermac code unconditionally sets
ppc_md.progress to NULL. This patch makes sure the powermac late
initcall is only run on powermac machines.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The "is_exec" branch of the protection check in do_page_fault()
didn't do anything on 32-bit PowerPC. So if a userland program
jumps to a page with Linux protection flags "---p", all the tests
happily fall through, and handle_mm_fault() is called, which in
turn calls handle_pte_fault(), which calls update_mmu_cache(),
which goes flush the dcache to a page with no access rights.
Boom.
This fixes it.
Signed-off-by: Segher Boessenkool <segher@kernel.crashing.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch adds fragments caused by rh_alloc_align() back to free list, instead
of allocating the whole chunk of memory. This will greatly improve memory
utilization managed by rheap.
It solves MURAM not enough problem with 3 UCCs enabled on MPC8323.
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Joakim Tjernlund <joakim.tjernlund@transmode.se>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is mainly to switch off all potentially debugging stuff that
won't report anything useful after an oops happened.
Besided that setting pause_on_oops will work too, but doesn't make
too much sense on s390.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print list of modules on die() like a lot of other architectures do.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When appending the 'cio_ignore' kernel parameter to the command line, a blank
has to be inserted in order to separate 'cio_ignore' from the preceding kernel
parameters.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The current implementation only handles -ERESTARTNOHAND, whereas we
also need to handle -ERESTART_RESTARTBLOCK in the handle_signal()
case for restartable system calls. Follows the sh change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The current implementation only handles -ERESTARTNOHAND, whereas we
also need to handle -ERESTART_RESTARTBLOCK in the handle_signal()
case for restartable system calls.
As noted by Carl:
This fixes the LTP test nanosleep03 - the current kernel causes
-ERESTART_RESTARTBLOCK to reach user space rather than the correct
-EINTR.
Reported-by: Carl Shaw <shaw.carl@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add the kernel release and version information to the output of
show_regs/oops. Add the CPU PSR register. Avoid using printk
to output partial lines; always output a complete line.
Re-combine the "Control" and "Table + DAC" lines after nommu
separated them; we don't want to waste vertical screen space
needlessly.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Russell helpfully pointed out on linux-arch:
http://marc.info/?l=linux-arch&m=118208089204630&w=2
We were missing the oops_enter/exit() in the sh die() implementation.
As we do support lockdep, it's beneficial to add these calls so lockdep
properly disables itself in the die() case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We use R0 as the 5th argument of syscall. When the syscall restarts
after signal handling, we should restore the old value of R0.
The attached patch does it. Without this patch, I've experienced random
failures in the situation which signals are issued frequently.
Signed-off-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add calls to oops_enter() and oops_exit() to __die(), so that
things like lockdep know when an oops occurs.
Add suffixes to the oops report to indicate whether the running
kernel has been built with preempt or smp support.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Distros seem to be removing PAGE_SIZE from asm/page.h. So, the libc side of
UML should stop using it.
I replace it with UM_KERN_PAGE_SIZE, which is defined to be the same as
PAGE_SIZE on the kernel side of the house. I could also use getpagesize(),
but it's more important that UML have the same value of PAGE_SIZE everywhere.
It's conceivable that it could be built with a larger PAGE_SIZE, and use of
getpagesize() would break that badly.
PAGE_MASK got the same treatment, as it is closely tied to PAGE_SIZE.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix oops triggered during: echo 0 > /proc/sys/kernel/nmi_watchdog
The culprit seems to be 09198e6850:
[PATCH] i386: Clean up NMI watchdog code
In two places, the parameters to release_{evntsel,perfctr}_nmi
got interchanged during the cleanup.
Fix interchanged parameters to release_{evntsel,perfctr}_nmi.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Stephane Eranian <eranian@hpl.hp.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When disabled through /proc/sys/kernel/nmi_watchdog, the NMI watchdog uses the
stop() method directly, which does not decrement the activity counter, leading
to a BUG(). Use the wrapper function instead to fix that.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
At system boot time, the NMI watchdog no longer reserved its MSRs, allowing
other subsystems to mess with them. Fix that.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (30 commits)
Blackfin SMC91X ethernet supporting driver: SMC91C111 LEDs are note drived in the kernel like in uboot
Blackfin SPI driver: fix bug SPI DMA incomplete transmission
Blackfin SPI driver: tweak spi cleanup function to match newer kernel changes
Blackfin RTC drivers: update MAINTAINERS information
Blackfin serial driver: decouple PARODD and CMSPAR checking from PARENB
Blackfin serial driver: actually implement the break_ctl() function
Blackfin serial driver: ignore framing and parity errors
Blackfin serial driver: hook up our UARTs STP bit with userspaces CMSPAR
Blackfin arch: move HI/LO macros into blackfin.h and punt the rest of macros.h as it includes VDSP macros we never use
Blackfin arch: redo our linker script a bit
Blackfin arch: make sure we initialize our L1 Data B section properly based on the linked kernel
Blackfin arch: fix bug can not wakeup from sleep via push buttons
Blackfin arch: add support for Alon Bar-Lev's dynamic kernel command-line
Blackfin arch: add missing gpio.h header to fix compiling in some pm configurations
Blackfin arch: As Mike pointed out range goes form m..MAX_BLACKFIN_GPIO -1
Blackfin arch: fix spelling typo in output
Blackfin arch: try to split up functions like this into smaller units according to LKML review
Blackfin arch: add proper ENDPROC()
Blackfin arch: move more of our startup code to .init so it can be freed once we are up and running
Blackfin arch: unify differences between our diff head.S files -- no functional changes
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix builds where MSC01E_xxx is undefined.
[MIPS] Separate performance counter interrupts
[MIPS] Malta: Fix for SOCitSC based Maltas
* 'for-linus' of git://www.atmel.no/~hskinnemoen/linux/kernel/avr32:
[AVR32] Define ARCH_KMALLOC_MINALIGN to L1_CACHE_BYTES
[AVR32] STK1000: Set SPI_MODE_3 in the ltv350qv board info
[AVR32] gpio_*_cansleep() fix
[AVR32] ratelimit segfault reporting rate
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (30 commits)
[PARISC] remove global_ack_eiem
[PARISC] Fix kernel panic in check_ivt
[PARISC] Fix bug when syscall nr is __NR_Linux_syscalls
[PARISC] be more defensive in process.c::get_wchan
[PARISC] fix "reduce size of task_struct on 64-bit machines" fallout
[PARISC] fix null ptr deref in unwind.c
[PARISC] fix trivial spelling nit in asm/linkage.h
[PARISC] remove remnants of parisc-specific softirq code
[PARISC] fix section mismatch in smp.c
[PARISC] fix "ENTRY" macro redefinition
[PARISC] Wire up utimensat/signalfd/timerfd/eventfd syscalls
[PARISC] fix section mismatch in superio serial drivers
[PARISC] fix section mismatch in parisc eisa driver
[PARISC] fix section mismatches in arch/parisc/kernel
[PARISC] fix section mismatch in ccio-dma
[PARISC] fix section mismatch in parisc STI video drivers
[PARISC] fix section mismatch in parport_gsc
[PARISC] fix lasi_82596 build
[PARISC] Build fixes for power.c
[PARISC] kobject is embedded in subsys, not kset
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix args to sun4v_ldc_revoke().
[SPARC64]: Really fix parport.
[SPARC64]: Fix IO/MEM space sizing for PCI.
[SPARC64]: Wire up cookie based sun4v interrupt registry.
Support for performance counter overflow interrupt that is on a separate
interrupt from the timer.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And an attempt to tidy up the core/controller differences.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In the latest incarnation of the ltv350qv driver the call to
spi_setup() has been removed. So we need to initialize things more
carefully in the board info struct.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Limit the rate of the kernel logging for the segfaults of user
applications, to avoid potential message floods or denial-of-service
attacks.
Signed-off-by: Andrea Righi <a.righi@cineca.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Previously, registering this early console would just result
in dropping early buffered printk output until a udbg_putc
was registered.
However, commit 69331af79c
clears the CON_PRINTBUFFER flag on the main console when a
CON_BOOT (early) console has been registered, resulting in
the buffered messages never being displayed to the user.
This fixes the problem by making sure we don't register udbg_console
on platforms that don't implement udbg_putc.
Signed-off-by: Milton Miller <miltonm@bga.com>
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The per-cpu area(a) for the secondary CPU(s) isn't getting allocated
on old SMP powermacs that don't have the secondary CPU(s) listed in
the device tree, as per-cpu areas are now only allocated for CPUs in
the cpu_possible_map, and we aren't setting the bits for the secondary
CPU(s) until smp_prepare_cpus(), which is after per-cpu allocation.
Therefore this sets the bits for CPUs 1..3 in cpu_possible_map in
pmac_setup_arch, so they get per-cpu data allocated.
Signed-off-by: Paul Mackerras <paulus@samba.org>
In pci_determine_mem_io_space(), do not hard code the region sizes.
Instead, use the values given to us in the ranges property.
Thanks goes to Mikael Petterson for the original Xorg failure
bug repoert, and strace dumps from Mikael and Dmitry Artamonow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Kudos to Thibaut Varene for spotting the (mis)use of appropriately named
global_ack_eiem. This took a long time to figure out and both insight
from myself, Kyle McMartin, and James Bottomley were required to narrow
down which bit of code could have this race condition.
The symptom was interrupts stopped getting delivered while some workload
was generating IO interrupts on two different CPUs. One of the interrupt
sources would get masked off and stay unmasked. Problem was global_ack_eiem
was accessed with read/modified/write sequence and not protected by
a spinlock.
PA-RISC doesn't need a global ack flag though. External Interrupts
are _always_ delivered to a single CPU (except for "global broadcast
interrupt" which AFAIK currently is not used.) So we don't have to worry
about any given IRQ vector getting delivered to more than one CPU.
Tested on a500 and rp34xx boxen. rsync to/from gsyprf11 (a500)
would lock up the box since NIC (tg3) interrupt and SCSI (sym2)
were on "opposite" CPUs (2 CPU system). Put them on the same CPU
or apply this patch and 10GB of data would rsync completely.
Please apply the following critical patch.
thanks,
grant
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Thibaut VARENE <T-Bone@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Fix smp barriers in test_and_{change,clear,set}_bit
[MIPS] Fix IP27 build
[MIPS] Fix modpost warnings by making start_secondary __cpuinit
[MIPS] SMTC: Fix build error caused by nonsense code.
[MIPS] SMTC: The MT ASE requires to initialize c0_pagemask and c0_wired.
[MIPS] SMTC: Don't continue in set_vi_srs_handler on detected bad arguments.
[MIPS] SMTC: Fix warning.
[MIPS] Wire up utimensat, signalfd, timerfd, eventfd
[MIPS] Atlas: Fix build.
[MIPS] Always install the DSP exception handler.
[MIPS] SMTC: Don't set and restore irqregs ptr from self_ipi.
[MIPS] Fix KMODE for the R3000
