Whole section about USB/eLBC configuration seems to be P1020 specific. So
add ifdefs to not compile it on other platforms (e.g. P2020).
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like for first 1G SDRAM map, do not enable Caching-inhibited nor Guarded
attribute for second 1G SDRAM mapping. Whole 2G SDRAM should use caches and
also allow speculative loading (by not setting Guarded attribute).
Also enable Memory Coherency attribute for second 1G SDRAM map. In commit
316f0d0f8f ("powerpc: mpc85xx: Fix static TLB table for SDRAM") it was
enabled for all SDRAM maps on all other boards, just missed this one case.
As a last thing, first 1G SDRAM map has wrong comment, so adjust it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When MPC85xx_PMUXCR_SDHC_WP is set then SDHC controller automatically makes
inserted SD card readonly if GPIO[9] is active.
In some design GPIO[9] pin does not have to be connected to SD card
write-protect pin and can be used as GPIO.
So do not set MPC85xx_PMUXCR_SDHC_WP bit when GPIO[9] is not used for
SDHC_WP functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As written in comment, P2020 has two possible SD switch configurations.
Extend code to detect both of them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Like in all other checks in checkboard() function, do not hang on error.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When env support is disabled then usage of env_init() or env_relocate()
generates linker errors. So do not compile env_init() or env_relocate()
in SPL code when env support is disabled in SPL.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
For now, this only provides reset and poweroff functions.
Signed-off-by: Michael Walle <michael@walle.cc>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an user-selectable SYS_HAS_ARMV8_SECURE_BASE, which has the
same meaning but is just for the ls1043ardb board. As no in-tree config
uses this, drop it and replace it with something more sophiticated:
ARMV8_PSCI_RELOCATE. This option will then enable the ARMV8_SECURE_BASE
option which is used as the base to relocate the PSCI code (or any code
in the secure region, but that is only PSCI). A SoC (or board) can now
opt-in into having such a secure region by enabling
SYS_HAS_ARMV8_SECURE_BASE. Enable it for the LS1043A SoC, where it was
possible to relocate the PSCI code before as well as on the LS1028A SoC
where there will be PSCI support soon.
Additionally, make ARMV8_PSCI and SEC_FIRMWARE_ARMV8_PSCI exclusive.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In arch/arm/mach-imx/imx8m/soc.c there's an implementation of
board_fix_fdt() introduced by commit 35bb60787b. Remove the
redundant one to avoid failed to build from source when enabling
CONFIG_OF_BOARD_FIXUP.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Since COUNTER_FREQUENCY is obselete, so set cntfrq_el0 if
CONFIG_COUNTER_FREQUENCY is valid
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Since versal has CONFIG_COUNTER_FREQUENCY, so use it. And
COUNTER_FREQUENCY will be dropped.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Enable DM_SERIAL for both U_Boot and the SPL. The uart4 and its pinmux
are already marked with u-boot,dm-spl but we need to move the call to
preloader_console_init() after spl_init() to avoid a board hang
as dm can't be used until after spl_init().
Remove the manual config of the UART pinmux now that it is no longer
needed.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Tested-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.
move the preloader_console_init() call after spl_early_init() to
avoid board hang
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Sancloud BeagleBone Enhanced Extended WiFi (BBE Extended WiFi) has
its own devicetree file and the board can be identified by the 2nd
letter of the config string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Sancloud BeagleBone Enhanced Lite (BBE Lite) has its own devicetree
file and the board can be identified by the 2nd letter of the config
string within the common EEPROM.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The Globalscale Technologies Sheevaplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Remove CONFIG_RESET_PHY_R symbol from all board files
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/sheevaplug/sheevaplug.h, use BIT macro, and add/cleanup
comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
The Colibri PXA270 has been end-of-life since quite a while and would
require more and more maintenance (e.g. DM conversions).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Gateworks produces many products from a single PCB with subloaded
components. Add an additional two levels of dtb name matching so that
for example a GW7400-A matches the dtb name of gw74xx.dtb
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- use the GSC driver functions
- move waiting for the EEPROM to the SPL int (it will always be ready
after this)
- move eeprom functions into eeprom file and elimate GSC_I2C_BUS
- eliminate some redundant EEPROM reads (the EEPROM must be read in
SPL before relocation, in SPL after relocation, and in U-Boot init.
All subsequent uses can use the global structure)
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Use the common GSC driver.
This allows us to do some additional cleanup:
- rename gsc{.c,.h} to eeprom{.c.h} for clarity
- collapse eeprom_get_dev
- remove unnecessary header files and alphabatize includes
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This fixes the following crash when run on a Colibri iMX7S aka solo:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000:
The i.MX 7Solo has only one single USB OTG1 but no USB host port. Trying
to initialize the nonexisting port just crashes.
While at it also drop board_usb_phy_mode() which is also no longer used
in the driver model age.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
DT node name should be generic, therefore rename atsha204a@64 to crypto@64.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Turris Omnia uses first MAC address from OTP for second ethernet interface.
Second MAC address for third interface and third MAC address for first
interface.
Other Turris routers do not have this rotate by one mapping. So add
function parameter for specifying id of the first ethernet interface.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Atsha device is used prior relocation and at this early stage BSS does not
have to be ready yet. So do not cache Atsha device in BSS.
Fixes support for other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
OTP code is not Atsha generic but also it is not Omnia specific. It is
common for all Turris routers which use Atsha cryptochip for storing OTP.
So move this common Turris specific Atsha OTP code from Turris Omnia into
separate file. It will be used also by other Turris routers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Allow to specify input parameters, define all available mbox commands
supported by CZ.NIC's secure firmware and also Marvell's fuse.bin firmware
and fix parsing response from Marvell OTP commands.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Generic A3720 mbox code is currently in Turris Mox specific board file
board/CZ.NIC/turris_mox/mox_sp.c. Move it to board independent arch file
arch/arm/mach-mvebu/armada3700/mbox.c.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When storing the UBoot Environment in for example EXT4,
the U-Boot build is broken for several reasons:
1. armada-385-turris-omnia-u-boot.dtsi will not allow
CONFIG_ENV_OFFSET and CONFIG_ENV_SIZE to be undefined
2. armada-37xx/board.c ft_board_setup function does not
exist if CONFIG_ENV_IS_IN_SPI_FLASH is not defined
This commit changes these files so that selecting a
different location for the environment is possible.
Signed-off-by: Rogier Stam <rogier@unrailed.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
Xilinx has been acquired by AMD that's why emails should be also updated.
The patch is updating .mailmap file and also MAINTAINERS files as was done
by commit 5cd1ecb994 ("ppc: qemu: Update MAINTAINERS for correct email
address").
The rest of my emails are not going to change.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
A number of rk3229/rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Google Veyron rk3288 DT files are synced from Linux.
Add a maintainer to look after them and to help with
review and testing.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DM9000 DM support
- tftp server bug fix
- mdio ofnode support functions
- Various phy fixes and improvements.
[trini: Fixup merge conflicts in drivers/net/phy/ethernet_id.c
drivers/net/phy/phy.c include/phy.h]
Add a structure which defines the information that is needed for
executing capsule updates on a platform. Some information in the
structure like the dfu string is used for making the update process
more robust while some information like the per platform image GUIDs
is used for fixing issues. Initialise this structure in the board
file, and use the information for the capsule updates.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy due
to part availability.
Add support for it by adding LED config and dt-prop based internal delay
config tx-delay/rx-delay per PHY ID.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The serial number is located at offset 0x14 of the EEPROM
under i2c0 bus at address 0x54.
To print the serial number in Linux:
SERNUM=$(cat /proc/device-tree/serial-number)
echo $SERNUM
Signed-off-by: Fabio Estevam <festevam@denx.de>
