Description is done without schematics only based on spec. It needs to be
validated when HW is ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add i2c accessible devices with description.
There is versal specific eeprom and i2c-gpio controller.
SE3 has also clock chip present.
Also remove x-prc description from SC dts.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add description based on specification and schematics.
All FIXMEs should be fixed when HW is ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add description based on specification and schematics.
All FIXMEs should be fixed when HW is ready.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file in
DDR and execute it first incase of jtag bootmode.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates scriptaddr value to 512MB as having it at 32MB has high
chance of script corruption incase of bigger kernel.
Be aware that 512MB is used for SPL malloc area that's why images should be
loaded after SPL (the best after u-boot relocation).
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds new jtag distro boot command to look for bootscript file
in DDR and execute it first incase of jtag bootmode.
This patch also updates scriptaddr to 512MB as there is high of script
corruption incase of bigger kernel image.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PSCI_RESET and EXPERT are not needed for mini
configurations so remove them to save space.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch sets the watchdog timeout-sec property to 60 seconds as default value.
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linux driver is not capable to handle 10Ohm shunt resistor.
That's why setup 1Ohm and setup proper calculation in user space.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch updates the AHB trigger adress that will be used by
the DAC/INDAC controllers for data transfers.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds clock driver support for Versal
platform. The clock driver queries and performs
clock operations using PLM firmware by communicating
with it using SMC calls.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add quirk for adjusting the GFLADJ register (global frame length
adjustment register) to trigger SOFs exactly at 125us time period.
Signed-off-by: Anurag Kumar Vulisha <anurag.kumar.vulisha@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable RTC node. RTC is used as a wakeup source for APU suspend-resume
use case. Also add alias for "rtc" as "rtc0".
Signed-off-by: Amit Sunil Dhamne <amit.sunil.dhamne@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In case of multiple sd devices to identify proper sd boot device
assign "sdbootdev" variable with device sequence number. While
auto-booting "sdboot" picks appropriate sd device from "sdbootdev".
This fix is for old way auto-boot process, it will be
deprecated in 2020.1 & all the functionality will be removed.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Raju Kumar Pothuraju <raju.kumar-pothuraju@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use auto MDI crossover for SGMII to support all cable setups.
Also correct MDIX mask bit.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch moves UHS mode macros from mmc.h to zynq_sdhci.c.
Moving UHS mode macros in mmc.h avoids redefinition of macros when
xenon_sdhci.c is compiled.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for the first data center card. Only memory and uart is
specified for initial bringup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
High speeds were broken in versal. This patch workarounds the issue and operates
SD in 25MHz.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is generic defconfig designed for autodetection (not added yet)
and then separate defconfigs directly used for certain x-prc card.
Octal SPI dts is added but not wired for x-prc specific defconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Detect which platform U-Boot is running at and based on that choose DTS
file which U-Boot uses for own configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Similar SCs but different wiring.
- dc_i2c is connected to X-PRC cards that's why label is required to have
an option to hook up some devices.
- Exactly identify i2c devices on x-prc boards.
In case of missing i2c connection devices won't be accessible.
- USB 0 should be device mode with super speed.
- USB 1 should be host mode.
- Fix i2c mux reset pin entry - commented, not verified.
- Fix i2c1 eeprom compatible string - it is an ST 128Kbit device.
Need to use atmel fallback.
- Fix si570 I2C slave address and add corresponding part numbers.
- Enable AMS for system monitoring.
- phy reset property should be commented because it will throw a
warning dump when called from context that can sleep.
No support for phys property (zynqmp phy driver) with SGMII.
Add is-internal-pcspma property required by uboot.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Identification depends on eeprom with FRU content.
For example 2 eeproms to check.
chosen {
xlnx,eeprom = <&eeprom>, <&eeprom2>;
};
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Idea is to have something what can be used for board bringup from
generic board perspective.
There is a violation compare to spec that FRU ID is ASCII8 instead of
binary format but this is really for having something to pass boot and
boot to OS which has better generating options.
Also time should be filled properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is a need to also end up strings with terminating char \0 to be
able to reread different structures.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
I didn't fully check it but I think that there is an issue to use FIT
images with dtb again when bss section is cleared. U-Boot copy just
origin DTB and if embedded_dtb_select() doesn't find new DTB then can't
go back to origin DTB file.
Move this structure to data section for now.
It should be allocated by malloc anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for fru commands "fru capture"
and "fru display". The fru capture parses the FRU table
present at an address and stores in a structure for later
use. The fru display prints the content of captured structured
in a readable format.
As of now, it supports only common header and board area of FRU.
Also, its supports only English language code and ASCII8 format.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This script transforms a pair of psu_init_gpl.c and .h files produced by
the Xilinx Vivado tool for ZynqMP into a smaller psu_init_gpl.c file that
is almost checkpatch compliant.
Based on a script by Michal Simek.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
