Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Adjust the following settings to get better timing and signal quality.
1. write DQS/DQ delay
- 1e6e2304[0]
- 1e6e2304[15:8]
2. read DQS/DQ delay
- 0x1e6e0298[0]
- 0x1e6e0298[15:8]
3. CLK/CA timing
- 0x1e6e01a8[31]
4. Read and write termination
- change RTT_ROM from 40 ohm to 48 ohm (MR1[10:8])
- change RTT_PARK from disable to 48 ohm (MR5[8:6])
- change RTT_WR from 120 ohm to disable (MR2[11:9])
- change PHY ODT from 40 ohm to 80 ohm (0x1e6e0130[10:8])
Note1: Both DDR-PHY and DDR controller have their own registers for DDR4
Mode Registers (MR0~MR6). This patch introduces macros to synchronize
the MR value on both sides.
Note2: the waveform meansurement can be found in item #21 of Aspeed
AST26x0 Application note (AP note).
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
The condition "~data" in the if-statement is a typo. The original
intention is to poll if SDRAM_PHYCTRL0_INIT bit equals to 0. So use
"data == 0" for instead.
Besides, the bit[1] of "phy_status" register is hardwired to
SDRAM_PHYCTRL0_INIT (with inverse logic). Since SDRAM_PHYCTRL0_INIT has
already done, remove the unnecessary checking of phy_status[1].
Fixes: fde9314346 ("ram: aspeed: Add AST2600 DRAM control support")
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
Invoking lseek() may result in an error. Handle it.
Addresses-Coverity-ID: 376212 ("Error handling issues (CHECKED_RETURN)")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Implement setbrg in amlogic/meson serial device with driver model
similar to how the meson_uart.c driver does it in Linux. Also
configure (probe) the serial device with the new reg5 register.
Signed-off-by: Edoardo Tomelleri <e.tomell@gmail.com>
Link: https://lore.kernel.org/r/20220918161701.572814-1-e.tomell@gmail.com
Acked-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
When cadence_qspi_versal_flash_reset() function is called in mini
u-boot where there is no firmware support, it is missing defines for
macro's BOOT_MODE_POR_0 & BOOT_MODE_POR_1. Remove them and replace with
already define macro's which have same values as these.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
Use dot instead of comma. The fix doesn't affect anything but it is good to
be aligned with used pattern. The first is used only for string size
calculation and the second change is in the comment.
Fixes: db681d4929 ("net: phy: Add new read ethernet phy id function")
Signed-off-by: Michal Simek <michal.simek@amd.com>
Current xilinx_timer_get_count() implementation does not take into account
the periodic 32-bit wrap arounds, as it directly returns the 32-bit counter
register value. The roll-overs cause problems in the upper timer layers, as
generic timer code expects an incrementing 64-bit value from get_count() to
work correctly.
Add the missing 64-bit up-conversion to fix random hangs/delays in
__udelay().
Fixes: a36d86720f ("microblaze: Convert axi timer to DM driver")
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20221012053656.1492457-3-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Relocate timer_ops pointers when CONFIG_NEEDS_MANUAL_RELOC is enabled.
The (gd->flags & GD_FLG_RELOC) check was added to make sure the reloc_done
logic works for drivers that use DM_FLAG_PRE_RELOC.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-2-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Align timer uclass with the other subsystems and provide a timer_get_ops()
convenience macro.
Using this instead of the generic device_get_ops() also prevents
-Wdiscarded-qualifiers warnings when used with non-const variables.
Signed-off-by: Ovidiu Panait <ovpanait@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20221012053656.1492457-1-ovpanait@gmail.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Since commit c2fd0ca1a8
("watchdog: Integrate watchdog triggering into the cyclic framework")
GD_FLG_WDT_READY has become write-only. This patch now removes this
flag completely.
The vacant spot in gd_flags is filled with the newly introduced
GD_FLG_CYCLIC_RUNNING flag.
Suggested-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Signed-off-by: Stefan Roese <sr@denx.de>
Checking for DM_RESET is not enough since not all watchdog
implementations use a reset lane. Such is the case for Rockchip
implementation for example. Since reset_assert_bulk will only succeed if
the resets property exists in the watchdog DT node, it needs to be
called only if a reset property is present.
This adds a condition on the resets property presence in the watchdog DT
node before assuming a reset lane needs to be fetched with
reset_assert_bulk, by calling ofnode_read_prop.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
DFU implementation does not bound the length field in USB
DFU download setup packets, and it does not verify that
the transfer direction. Fixing the length and transfer
direction.
CVE-2022-2347
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Sync the critical clocks in the U-Boot driver with those marked as
critical in Linux. The Linux driver has an explanation of why each clock
is considered to be critical, so import that too.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Not all "periph" clocks are children of the AHB clock, some have the AXI
clock as their parent & the mtimer clock is derived from the external
reference clock directly. Stop assuming the AHB clock to be the parent
of all "periph" clocks and define their correct parents instead.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
The original devicetrees for PolarFire SoC messed up & defined the
msspll's output as a fixed-frequency, 600 MHz clock & used that as the
input for the clock controller node. The msspll is not a fixed
frequency clock and later devicetrees handled this properly. Check the
devicetree & if it is one of the fixed ones, register the msspll.
Otherwise, skip registering it & pass the reference clock directly to
the cfg clock registration function so that existing devicetrees are
not broken by this change.
As the MSS PLL is not a "cfg" or a "periph" clock, add a new driver for
it, based on the one in Linux.
Fixes: 2f27c9219e ("clk: Add Microchip PolarFire SoC clock driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Tested-by: Padmarao Begari <padmarao.begari@microchip.com>
Currently the clock driver for PolarFire SoC takes a very naive approach
to the relationship between clocks. It reads the dt to get an input
clock, assumes that that is fixed frequency, reads the "clock-frequency"
property & uses that to set up both the "cfg" and "periph" clocks.
Simplifying for the sake of incremental fixes, the "correct" parentage for
the clocks currently supported in U-Boot is that the "cfg" clocks should
be children of the fixed frequency clock in the dt. The AHB clock is one
of these "cfg" clocks and is the parent of the "periph" clocks.
Instead of passing the clock rate of the fixed-frequency clock to the
"cfg" and "periph" registration functions and the name of the parents,
pass their actual parents & use clk_get_rate() to determine their parents
rates.
The "periph" clocks are purely gate clocks and should not be reading the
AHB clocks registers to determine their rates, as they can simply report
the output of clk_get_rate() on their parent.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add newline at the end of the printed string.
Signed-off-by: Sergei Antonov <saproj@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
A late ack is currently being sent at the end of a transfer due to
incorrect logic in mchp_corei2c_empty_rx(). Currently the Assert Ack
bit is being written to the controller's control reg after the last
byte has been received, causing it to sent another byte with the ack.
Instead, the AA flag should be written to the control register when
the penultimate byte is read so it is sent out for the last byte.
Reported-by: Andreas Buerkler <andreas.buerkler@enclustra.com>
Fixes: 0dc0d1e094 ("i2c: Add Microchip PolarFire SoC I2C driver")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Removed Tag by hs: Fixes: 0190d48488 ("i2c: microchip: fix ack sending logic")
"Master receive mode" was not correctly sending ACKs/NACKs in the
interrupt handler. Bring the handling of M_SLAR_ACK, M_RX_DATA_ACKED &
M_RX_DATA_NACKED in line with the Linux driver.
Fixes: 0dc0d1e094 ("i2c: Add Microchip PolarFire SoC I2C driver")
Reported-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This reverts commit c7878a0483.
Since commit c7878a0483 ("serial: mxc: have putc use the TXFIFO"),
serial console corruption can be seen when priting inside board_init().
Revert it to avoid the regression.
Reported-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_4BIT_HW_ECC_OOBFIRST
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_MMC_MAX_BLK_COUNT
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
This converts the following to Kconfig:
CONFIG_SYS_MAX_NAND_DEVICE
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_INTERLAKEN
CONFIG_SYS_ISA_IO
CONFIG_SYS_ISA_IO_BASE_ADDRESS
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_I2C_INIT_BOARD
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The description claims that the device is probed but it isn't.
Add the device_probe() call.
Also consolidate the iteration into one function.
Fixes: 8a5cbc065d ("dm: blk: Use uclass_find_first/next_device() in blk_first/next_device()")
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
Create a block driver for the new HOST uclass. This handles attaching and
detaching host files.
For now the uclass is not used but this will be plumbed in with future
patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sandbox supports block devices which can access files on the host machine.
At present there is no uclass for this. The devices are attached to the
root devic. The block-device type is therefore set to UCLASS_ROOT which
is confusing.
Block devices should be attached to a 'media' device instead, something
which handles access to the actual media and provides the block driver
for the block device.
Create a new uclass to handle this. It supports two operations, to attach
and detach a file on the host machine.
For now this is not fully plumbed in.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function now finds its block-device child by looking for a child
device of the correct uclass (UCLASS_BLK). It cannot produce a device of
any other type, so drop the superfluous check.
Provide a version which does not probe the device, since that is often
needed when setting up the device's platdata.
Also fix up the function's comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some tests access data in block devices and so cause the cache to fill
up. This results in memory being allocated.
Some tests check the malloc usage at the beginning and then again at the
end, to ensure there is no memory leak caused by the test. The block cache
makes this difficult, since the any test may cause entries to be allocated
or even freed, if the cache becomes full.
It is simpler to clear the block cache after each test. This ensures that
it will not introduce noise in tests which check malloc usage.
Add the logic to clear the cache, using the existing blkcache_invalidate()
function. Drop the duplicate code at the same time.
Signed-off-by: Simon Glass <sjg@chromium.org>
The support added later in this series tweaks the PMIC voltages in the
SPL. Enable support for the rn5t567 in SPL builds to allow this to be done
cleanly.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for the rn5t568 PMIC to the rn5t567 driver.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Jaehoon Chung <j80.chung@samsung.com>
If the bd718x7 is required, but PMIC_CHILDREN is disabled, this
driver throws a compile error. Fix this by putting the function
to bind children into an if-statement checking for PMIC_CHILDREN.
Allowing PMIC_CHILDREN to be disabled in SPL saves some space and
still permits some read/write functions to access the PMIC in
early startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Unlike the other 64-bit mvebu SoCs the AlleyCat5 uses the older ehci
block from the 32-bit SoCs. Adapt the ehci-marvell.c driver to cope with
the fact that the ac5 does not have the mbus infrastructure the 32-bit
SoCs have and ensure USB_EHCI_IS_TDI is selected.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for the AlleyCat5 SoC. This lacks the mbus from the other
users of the mvneta.c driver so a new compatible string is needed to
allow for a different window configuration.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
