Commit afbbd413a fixed this for non-driver-model. Make sure that the driver
model code handles this also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust minnowmax to use driver model for PCI. This requires adding a device
tree node to specify the ranges, removing the board-specific PCI code and
ensuring that the host bridge is configured.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver should use the x86 PCI configuration functions. Also adjust its
compatible string to something generic (i.e. without a vendor name).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Store VESA parameters to Linux setup header so that vesafb driver
in the kernel could work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jian Luo <jian.luo4@boschrexroth.de>
MARK_GRAPHICS_MEM_WRCOMB is not referenced anywhere in the code,
hence remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move X86_OPTION_ROM_FILE & X86_OPTION_ROM_ADDR to arch/x86/Kconfig
and rename them to VGA_BIOS_FILE & VGA_BIOS_ADDR which depend on
HAVE_VGA_BIOS. The new names are consistent with other x86 binary
blob options like HAVE_FSP/FSP_FILE/FSP_ADDR.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Print the meaningful base address and mask of an MTRR range without showing
the memory type encoding or valid bit.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Per CPUID:80000008h result, the maximum physical address bits of
TunnelCreek processor is 32 instead of default 36. This will fix
the incorrect decoding of MTRR range mask.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should setup fixed range MTRRs for some legacy regions like VGA
RAM and PCI ROM areas as uncacheable. Note FSP may setup these to
other cache settings, but we can override this in x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should allow pci config read/write to host bridge (b.d.f = 0.0.0)
in the int1a_handler() which is a valid pci device.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PCI option rom may use different SS during its execution, so it is not
safe to assume esp pointed to the same location in the protected mode.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far interrupt routing works pretty well for any on-chip devices
on Intel Crown Bay. When inserting any PCIe card to any PCIe slot,
Linux kernel is smart enough to do interrupt swizzling and figure
out device's irq using its parent bridge's interrupt routing info
all the way up to its root port. In U-Boot all PCIe root ports'
interrupts were routed to PIRQ E/F/G/H before, while actually all
PCIe downstream ports received INTx are routed to PIRQ A/B/C/D
directly and not configurable. Now we change this mapping so that
any external PCIe device can work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement write_mp_table() to create a minimal working MP table.
This includes an MP floating table, a configuration table header
and all of the 5 base configuration table entries. The I/O interrupt
assignment table entry is created based on the same information used
in the creation of PIRQ routing table from device tree. A check
duplicated entry logic is applied to prevent writing multiple I/O
interrupt entries with the same information.
Use a Kconfig option GENERATE_MP_TABLE to tell U-Boot whether we
need actually write the MP table at the F seg, just like we did for
PIRQ routing and SFI tables. With MP table existence, linux kernel
will switch to I/O APIC and local APIC to process all the peripheral
interrupts instead of 8259 PICs. This takes full advantage of the
multicore hardware and the SMP kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The MP table provides a way for the operating system to support
for symmetric multiprocessing as well as symmetric I/O interrupt
handling with the local APIC and I/O APIC. We provide a bunch of
APIs for U-Boot to write the floating table, configuration table
header as well as base and extended table entries.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove inline for lapic access routines and expose lapic_read()
& lapic_write() as APIs to read/write lapic registers. Also move
stop_this_cpu() to mp_init.c as it has nothing to do with lapic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
I/O APIC registers are addressed indirectly. Add io_apic_read() and
io_apic_write() routines to help register access. Two macros for I/O
APIC ID and version register offset are also added.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is no need to populate multiple irq info entries with the same
bus number and device number, but with different interrupt pin. We
can use the same entry to store all the 4 interrupt pin (INT A/B/C/D)
routing information to reduce the whole PIRQ routing table size.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In fill_irq_info() pci device's function number is written into
the table, however this is not really necessary. The function
number can be anything as OS doesn't care about this field,
neither does the PIRQ routing specification. Change to always
writing 0 as the function number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We should write correct bus number to the PIRQ routing table for the
irq router from device tree, instead of hard-coded zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 4 usb ports on the Intel Crown Bay board, 2 of which are
connected to Topcliff usb host 0 and the other 2 connected to usb
host 1. USB devices inserted in the ports connected to usb host 1
cannot get detected due to wrong IRQ assigned to the controller.
Actually we need apply the PCI interrupt pin swizzling logic to all
devices on the Topcliff chipset when configuring the PIRQ routing.
This was observed on usb ports, but device 6 and 10 irqs are also
wrong. Correct them all together.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Crown Bay board has a TunnelCreek processor which supports
hyper-threading. Add /cpus node in the crownbay.dts and enable
the MP initialization.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
(modified to remove error:
overriding the value of OF_CONTROL. Old value: "y", new value: "y")
This commit cleans up the lapic codes:
- Delete arch/x86/include/asm/lapic_def.h, and move register and bit
defines into arch/x86/include/asm/lapic.h
- Use MSR defines from msr-index.h in enable_lapic() and disable_lapic()
- Remove unnecessary stuff like NEED_LAPIC, X86_GOOD_APIC and
CONFIG_AP_IN_SIPI_WAIT
- Move struct x86_cpu_priv defines to asm/arch-ivybridge/bd82x6x.h, as
it is not apic related and only used by ivybridge
- Fix coding convention issues
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently lapic_setup() is called before calling mp_init(), which
then calls init_bsp() where it calls enable_lapic(), which was
already enabled in lapic_setup(). Hence move lapic_setup() call
into init_bsp() to avoid the duplication.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Most of the MP initialization codes in arch/x86/cpu/baytrail/cpu.c is
common to all x86 processors, except detect_num_cpus() which varies
from cpu to cpu. Move these to arch/x86/cpu/cpu.c and implement the
new 'get_count' method for baytrail and cpu_x86 drivers. Now we call
cpu_get_count() in mp_init() to get the number of CPUs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move MAX_CPUS definition after SMP so that it shows below SMP in the
menuconfig. Also replace the leading spaces in the MAX_CPUS section
with tabs to conform coding standard.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit does the following to clean up x86 cpu dm drivers:
- Move cpu_x86 driver codes from arch/x86/cpu/cpu.c to a dedicated
file arch/x86/cpu/cpu_x86.c
- Rename x86_cpu_get_desc() to cpu_x86_get_desc() to keep consistent
naming with other dm drivers
- Add a new cpu_x86_bind() in the cpu_x86 driver which does exactly
the same as the one in the intel baytrail cpu driver
- Update intel baytrail cpu driver to use cpu_x86_get_desc() and
cpu_x86_bind()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The call to FspInitEntry is done in arch/x86/lib/fsp/fsp_car.S so far.
It worked pretty well but looks not that good. Apart from doing too
much work than just enabling CAR, it cannot read the configuration
data from device tree at that time. Now we want to move it a little
bit later as part of init_sequence_f[] being called by board_init_f().
This way it looks and works better in the U-Boot initialization path.
Due to FSP's design, after calling FspInitEntry it will not return to
its caller, instead it jumps to a continuation function which is given
by bootloader with a new stack in system memory. The original stack in
the CAR is gone, but its content is perserved by FSP and described by
a bootloader temporary memory HOB. Technically we can recover anything
we had before in the previous stack, but that is way too complicated.
To make life much easier, in the FSP continuation routine we just
simply call fsp_init_done() and jump back to car_init_ret() to redo
the whole board_init_f() initialization, but this time with a non-zero
HOB list pointer saved in U-Boot's global data so that we can bypass
the FspInitEntry for the second time.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Currently the FSP execution environment GDT is setup by U-Boot in
arch/x86/cpu/start16.S, which works pretty well. But if we try to
move the FspInitEntry call a little bit later to better fit into
U-Boot's initialization sequence, FSP will fail to bring up the AP
due to #GP fault as AP's GDT is duplicated from BSP whose GDT is
now moved into CAR, and unfortunately FSP calls AP initialization
after it disables the CAR. So basically the BSP's GDT still refers
to the one in the CAR, whose content is no longer available, so
when AP starts up and loads its segment register, it blows up.
To resolve this, we load GDT before calling into FspInitEntry.
The GDT is the same one used in arch/x86/cpu/start16.S, which is
in the ROM and exists forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add RESET_SEG_START, RESET_SEG_SIZE and RESET_VEC_LOC Kconfig options
and make arch/x86/cpu/config.mk use these options.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Tested-by: Simon Glass <sjg@chromium.org>
Some archs/boards specify their own default by pre-defining the config
which causes the Kconfig system to mix up the order of the configs in
the defconfigs... This will cause merge pain if allowed to proliferate.
Remove the configs that behave this way from the archs.
A few configs still remain, but that is because they only exist as
defaults and do not have a proper Kconfig entry. Those appear to be:
SPIFLASH
DISPLAY_BOARDINFO
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[trini: rastaban, am43xx_evm_usbhost_boot, am43xx_evm_ethboot updates,
drop DM_USB from MSI_Primo81 as USB_MUSB_SUNXI isn't converted yet to DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Every pin can be configured now from the device tree. A dt-bindings
has been added to describe the different property available.
Change-Id: I1668886062655f83700d0e7bbbe3ad09b19ee975
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Acked-by: Simon Glass <sjg@chromium.org>
Baytrail physically maps the first 2 GB of SDRAM from 0x0 to 0x7FFFFFFF
and additional SDRAM is mapped from 0x100000000 and up. There is a
physical memory hole from 0x80000000 to 0xFFFFFFFF for other uses.
Because of this, PCI region 3 should only try to use up to the amount of
SDRAM or 0x80000000, which ever is less.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Support QEMU PIRQ routing via device tree on both i440fx and q35
platforms. With this commit, Linux booting on QEMU from U-Boot
has working ATA/SATA, USB and ethernet.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Writing 0xcb to I/O port 0xb2 (Advanced Power Management Control) causes
U-Boot to hang on QEMU q35 target. We introduce a config option in the
device tree "u-boot,no-apm-finalize" under /config node if we don't want
to do that.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although the two qemu-x86 targets (i440fx and q35) share a lot in
common, they still have something that cannot easily handled in one
single device tree). Split to create two dedicated device tree files
and make the i440fx be the default build target.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
As VGA option rom needs to run at C segment, although QEMU PAM emulation
seems to only guard E/F segments, for correctness, move VGA initialization
after PAM decode C/D/E/F segments.
Also since we already tested QEMU targets to differentiate I440FX and Q35
platforms, change to locate the VGA device via hardcoded b.d.f instead of
dynamic search for its vendor id & device id pair.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
QEMU always decode legacy IDE I/O ports on PIIX chipset. However Linux ata_piix
driver does sanity check to see whether legacy ports decode is turned on.
To make Linux ata_piix driver happy, turn on the decode via IDE_TIMING register.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the legacy segments C/D/E/F do not decode to system RAM.
Turn on the decode via Programmable Attribute Map (PAM) registers
so that we can write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
High mem starts at 4 GiB.
Signed-off-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If pirq_routing_table points to NULL, that means U-Boot fails to
generate the table before in create_pirq_routing_table(), so we
test it against NULL before actually writing it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Quark SoC has the same interrupt routing mechanism as the
Queensbay platform, only the difference is that PCI devices'
INTA/B/C/D are harcoded and cannot be changed freely.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
PIRQ routing is pretty much common in Intel chipset. It has several
PIRQ links (normally 8) and corresponding registers (either in PCI
configuration space or memory-mapped IBASE) to configure the legacy
8259 IRQ vector mapping. Refactor current Queensbay PIRQ routing
support using device tree and move it to a common place, so that we
can easily add PIRQ routing support on a new platform.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It turns out that QEMU x86 emulated graphic card has a built-in
option ROM which can be run perfectly with native mode by U-Boot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_FRAMEBUFFER_SET_VESA_MODE and CONFIG_FRAMEBUFFER_VESA_MODE
are not x86-specific, so move them to drivers/video/Kconfig and
make them depend on VIDEO_VESA driver. Some cosmetic fixes are
applied to the Kconfig help text as well.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we have QEMU support, make it the default vendor in the
'make menuconfig' screen.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This commit introduces the initial U-Boot support for QEMU x86 targets.
U-Boot can boot from coreboot as a payload, or directly without coreboot.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Merged in patch 'x86: qemu: Add CMD_NET to qemu-x86_defconfig
https://patchwork.ozlabs.org/patch/479745/
Enable the CPU uclass and Simple Firmware interface for Minnowbaord MAX. This
enables multi-core support in Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This driver supports multi-core init and sets up the CPU frequencies
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This permits init of additional CPU cores after relocation and when driver
model is ready.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since we do these sorts of operations a lot, it is useful to have a simpler
API, similar to clrsetbits_le32().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Most modern x86 CPUs include more than one CPU core. The OS normally requires
that these 'Application Processors' (APs) be brought up by the boot loader.
Add the required support to U-Boot to init additional APs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a function to return the address of the Interrupt Descriptor Table.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When we start up additional CPUs we want them to use the same Global
Descriptor Table. Store the address of this in global_data so we can
reference it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a subset of this header file from Linux 4.0 to support atomic operations
in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This provides a way of passing information to Linux without requiring the
full ACPI horror. Provide a rudimentary implementation sufficient to be
recognised and parsed by Linux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is annoying during development and serves no useful purpose since
warnings are clearly displayed now that we are using Kbuild. Remove this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port on boards that use a Firmware Support Package (FSP).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Now that reset_cpu() functions correctly, use it instead of directly
accessing the port.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The existing code is pretty ancient and is unreliable on modern hardware.
Generally it will hang.
We can use port 0xcf9 to initiate reset on more modern hardware (say in the
last 10 years). Update the reset_cpu() function to do this, and add a new
'full reset' function to perform a full power cycle.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot on coreboot does not have a driver for the PCH so cannot see the
SPI peripheral now that it has moved inside the PCH. Add a simple driver so
that SPI flash works again.
Signed-off-by: Simon Glass <sjg@chromium.org>
The SPI NOR on the minnowboard max is a MICRON N25Q064A
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since all x86 boards have been converted to use DM_SPI and
DM_SPI_FLASH, move them to arch/Kconfig x86 section.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove the ending period of the MARK_GRAPHICS_MEM_WRCOMB option. Also
fix the indention of its help text.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move platform-specific options under in arch/x86/Kconfig forward right
after the board-specific options but before any architecture-specific
options. When it comes to the same Kconfig option, board-specific one
takes take the highest precedence, then platform-specific one, and
finally architecture-specific one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Let arch/x86/Kconfig prompt board vendor first, then select
the board model under that vendor. This way arch/x86/Kconfig
only needs concern board vendor and leave the supported target
list to board/<vendor>/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the legacy segments (A0000h-B0000h, E0000h-F0000h)
do not decode to system RAM. Turn on the decode so that we can
write configuration tables in the F segment.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Previously the PIRQ routing table sanity check was performed against
the original table provided by the platform codes. Now we switch to
check its sanity on the final table in the F segment as this one is
the one seen by the OS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are 6 banks:
4 banks for CORE: available in S0 mode
2 banks for SUS (Suspend): available in S0-S5 mode
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The correct GPIOBASE address on the baytrail is 0x48
Signed-off-by: Gabriel Huau <contact@huau-gabriel.fr>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement Intel Queensbay platform-specific PIRQ routing support.
The chipset PIRQ routing setup is called in the arch_misc_init().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On x86 boards, platform chipset receives up to four different
interrupt signals from PCI devices (INTA/B/C/D), which in turn
will be routed to chipset internal PIRQ lines then routed to
8259 PIC finally if configuring the whole system to work under
the so-called PIC mode (in contrast to symmetric IO mode which
uses IOAPIC).
We add two major APIs to aid this, one for routing PIRQ and the
other one for generating a PIRQ routing table.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
We can write the configuration table in last_stage_init() for all x86
boards, but not with coreboot since coreboot already has them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a function to assign an IRQ number to PCI device's interrupt
line register in its configuration space, so that the PCI device
can have its interrupt working under PIC mode after OS boots up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Create a default e820 table with 3 entries which is enough to boot
a Linux kernel.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since Intel ICH SPI driver has been converted to driver model, we need
add an alias for SPI node in the board dts files otherwise SPI flash
won't be detected due to 'invalid bus' error.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
For starting a Linux console on the superio serial port under
interrupt mode, the IRQ number must be configured.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The prefix PCH was taken from ivybridge port. However Queensbay
platform official document does not mention PCH. It is composed
of TunnelCreek processor and Topcliff IOH chipset. For accuracy,
avoid using PCH prefix in the macro.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
As mentioned in the previous commit, adding default values in each
Kconfig causes problems because it does not co-exist with the
"depends on" syntax. (Please note this is not a bug of Kconfig.)
We should not do so unless we have a special reason. Actually,
for CONFIG_DM*, we have no good reason to do so.
Generally, CONFIG_DM is not a user-configurable option. Once we
convert a driver into Driver Model, the board only works with Driver
Model, i.e. CONFIG_DM must be always enabled for that board.
So, using "select DM" is more suitable rather than allowing users to
modify it. Another good thing is, Kconfig warns unmet dependencies
for "select" syntax, so we easily notice bugs.
Actually, CONFIG_DM and other related options have been added
without consistency: some into arch/*/Kconfig, some into
board/*/Kconfig, and some into configs/*_defconfig.
This commit prefers "select" and cleans up the following issues.
[1] Never use "CONFIG_DM=n" in defconfig files
It is really rare to add "CONFIG_FOO=n" to disable CONFIG options.
It is more common to use "# CONFIG_FOO is not set". But here, we
do not even have to do it.
Less than half of OMAP3 boards have been converted to Driver Model.
Adding the default values to arch/arm/cpu/armv7/omap3/Kconfig is
weird. Instead, add "select DM" only to appropriate boards, which
eventually eliminates "CONFIG_DM=n", etc.
[2] Delete redundant CONFIGs
Sandbox sets CONFIG_DM in arch/sandbox/Kconfig and defines it again
in configs/sandbox_defconfig.
Likewise, OMAP3 sets CONFIG_DM arch/arm/cpu/armv7/omap3/Kconfig and
defines it also in omap3_beagle_defconfig and devkit8000_defconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The PCH (Platform Controller Hub) is on the PCI bus, so show it as such.
The LPC (Low Pin Count) and SPI bus are inside the PCH, so put these in the
right place also.
Rename the compatible strings to be more descriptive since this board is the
only user. Once we are using driver model fully on x86, these will be
dropped.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 systems this device is commonly used to provide legacy port access.
It is sort-of a replacement for the old ISA bus.
Add a uclass for this, and allow it to have child devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple uclass for this chip which is often found in x86 systems
where the CPU is a separate device.
The device can have children, so make it scan the device tree for these.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move chromebook_link over to driver model for PCI.
This involves:
- adding a uclass for platform controller hub
- removing most of the existing PCI driver
- adjusting how CPU init works to use driver model instead
- rename the lpc compatible string (it will be removed later)
This does not really take advantage of driver model fully, but it does work.
Furture work will improve the code structure to remove many of the explicit
calls to init the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
