Ethernet phy like dp83867 is using strapping resistors to setup PHY
address. On Xilinx boards strapping is setup on wires which are connected
to SOC where internal pull ups/downs influnce phy address. That's why there
is a need to setup pins properly (via pinctrl driver for example) and then
perform phy reset. I can be workarounded by reset gpio done for mdio bus
but this is not working properly when multiply phys sitting on the same
bus. That's why it needs to be done via ethernet-phy-id driver where dt
binding has gpio reset per phy.
DT binding is available here:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/net/ethernet-phy.yaml
The driver is are reading the vendor and device id from valid phy node
using ofnode_read_eth_phy_id() and creating a phy device.
Kconfig PHY_ETHERNET_ID symbol is used because not every platform has gpio
support.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Link: https://lore.kernel.org/r/70ab7d71c812b2c972d48c129e416c921af0d7f5.1645627539.git.michal.simek@xilinx.com
Add support for dynamic configuration which will takes care of
configuring the SD secure space configuration registers using firmware
APIs, performing SD reset assert and deassert.
High level sequence:
- Check for the PM dynamic configuration support, if no error proceed
with SD dynamic configurations(next steps) otherwise skip the dynamic
configuration.
- Put the SD Controller in reset.
- Configure SD Fixed configurations.
- Configure the SD Slot Type.
- Configure the BASE_CLOCK.
- Configure the 8-bit support.
- Bring the SD Controller out of reset.
In the above steps, apart from the Fixed configurations, remaining all
configurations are dynamic and they will be read from devicetree.
And also remove hardcoded secure register writes, as dynamic sd config
support is added.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/030a3ec041ff3efebd574b4d2b477ad85f12cbce.1645626962.git.michal.simek@xilinx.com
Most of the frequencies are not rounded up to a proper number.
When we need to devide these frequencies to get a number for example
frequency in Mhz, we see it as one less than the actual intended value.
Ex: If we want to get Mhz from frequency 199999994hz, we will calculate
it using div64_u64(199999994, 1000000) and we will get 199Mhz in place
of 200Mhz.
Add a macro DIV64_U64_ROUND_UP for rounding up div64_u64. This is taken
from linux 'commit 68600f623d69("mm: don't miss the last page because of
round-off error")'.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/f9fdcba76cd692ae436b1d7883b490e3dc207231.1645626962.git.michal.simek@xilinx.com
The main reason is to send pmufw cfg overlay from U-Boot to PMUFW to enable
access to DP. Overlay is sent when cls command is called and for that IP
has to be enabled in carrier cards.
And IP needs to be also enabled in SOM dt because with DTB reselection new
DT is not parsed in pre reloc U-Boot instance. It is called from board_f
via embedded_dtb_select(). That's why bind function is not able to allocate
memory and it ends up with error:
"Video device 'display@fd4a0000' cannot allocate frame buffer memory
-ensure the device is set up before relocation"
To avoid this situation DP is placed also to SOM where bind function is
called and frame buffer memory is allocated and just reused after DTB
reselection. Result is the same. There could be a problem in Linux with
different DP configurations but that's need to be solved there because
console should be on from u-boot already.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/c4f31641f917fddb09d976f56875057c658f264c.1645629459.git.michal.simek@xilinx.com
Since OpenSSL 1.1.0, EVP_MD_CTX_create() is EVP_MD_CTX_new()
EVP_MD_CTX_destroy() is EVP_MD_CTX_free()
EVP_MD_CTX_init() is EVP_MD_CTX_reset()
As there's no need to reset a newly created EVP_MD_CTX, moreover
EVP_DigestSignInit() does the reset, thus call to EVP_MD_CTX_init()
can be dropped.
As there's no need to reset an EVP_MD_CTX before it's destroyed,
as it will be reset by EVP_MD_CTX_free(), call to EVP_MD_CTX_reset()
is not needed and can be dropped.
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Based on looking at top contributors it was seen that top statistics from
top contributors don't include all contributions from different email
addresses. That's why I checked all top contributors are checked it.
git shortlog -n $START..$END -e -s
The patch is adding mapping for Bin Meng, Marek Vasut, Masahiro Yamada,
Michal Simek, Tom Rini, Wolfgang Denk.
And also use mapping for Stefan Roese and Wolfgang Denk to be properly
counted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
If parameter -F is given but FIT support is missing, a NULL pointer might
dereferenced (Coverity CID 350249).
If incorrect parameters are given, provide a message and show usage.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Recent unrelated fixes (9876ae7db6) revealed that we were missing bits
from 2af181b53e in the IOT2050 dt. Add them, but only for main U-Boot.
SPL loads from QSPI only, thus cannot use DMA.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Public documents about BootROM of some Marvell SoCs are available in the
public Web Archive. Put this information into source code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Testes proved that current kwboot version supports also Avanta SoCs.
It looks like that Avanta SoCs are using same kwbimage format as Armada.
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Document -D, -b, -d, -q and -s options.
Add common examples how to use kwboot.
Add information about Armada 38x BootROM bug for debug console mode and how
to workaround it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Add all supported Armada SoCs and document -b and -d options in usage.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Marvell BootROM recognize only '\b' byte as backspace. Use terminfo
for retrieving current backspace sequence and replace any occurrence of
backspace sequence by the '\b' byte.
Reading terminfo database is possible via tigetstr() function from system
library libtinfo.so.*. So link kwboot with -ltinfo.
Normally terminfo functions are in <term.h> system header file. But this
header file conflicts with U-Boot "termios_linux.h" header file. So declare
terminfo functions manually.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
