The PE clock have two parents, add support for picking the correct
one and deriving the clock from it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PLL rate could be in the GHz range, which could overflow a 32bit
data type. Since the hardware is 64bit anyway, pass the clock rates
as 64bit number internally to avoid this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mul and div arguments were reported in reverse order in the debug
message, swap them to fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
dm_warn is too noisy, replace with dev_dbg for less noise.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Since b0ba1e7e9d
(rockchip: clk: rk3288: add clk_enable function and support USB HOST0/HSIC)
Ethernet no longer probes on RK3288.
Add no-ops for GMAC clocks observed to be requested which match the
clk_enable cases in RK3368 and RK3399.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Cc: Wadim Egorov <w.egorov@phytec.de>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for the clk dump command on Armada 37xx.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The drivers are based on Linux driver by Gregory Clement.
The TBG clocks support only the .get_rate method.
- since setting rate is not supported, the driver computes the rates
when probing and so subsequent calls to the .get_rate method do not
read the corresponding registers again
The peripheral clocks support methods .get_rate, .enable and .disable.
- the .set_parent method theoretically could be supported on some clocks
(the parent would have to be one of the TBG clocks)
- the .set_rate method would have to try all the divider values to find
the best approximation of a given rate, and it doesn't seem like
this should be needed in U-Boot, therefore not implemented
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add VREF clock gating, that may be used by STM32 VREFBUF regulator.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested By: Bruno Herrera <bruherrera@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The R8A7792 does not have the USB extal, so drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.
This implements a minimal clk_enable for the RK3288 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The last clock consumer in SPL, SD/eMMC driver, gave up using the
clock driver. The clock driver is only used in U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The initconst is not used in U-Boot, drop it. The r8a7794_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The initconst is not used in U-Boot, drop it. The r8a7792_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add clock control for ethernet controller on each SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This fixes the Coverity Defect CID 175347 when dev_count_phandle_with_args()
returns a negative value.
Fixes: a855be87da ("clk: Add get/enable/disable/release for a bulk of clocks")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The initconst is not used in U-Boot, drop it. The r8a7790_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds the bulk clock API tests for the sandbox test suite.
It's very similar to the main test but only uses the _bulk() API and
checks if the clocks are correctly enabled/disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds a "bulk" API to the clock API in order to get/enable/disable
/release a group of clocks associated with a device.
This bulk API will avoid adding a copy of the same code to manage
a group of clocks in drivers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The STGEN is the clock source for the Cortex A7 arch timer.
So after modification of its frequency, CP15 cntfreq is updated
and a new timer init is performed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The patch set dpll settings for 300MHz to values used by binary
blob[1]. With new values dpll still generate 300MHz clock, but
EMAC work. Probably with new values dpll generate more stable clock.
dpll on rk3188 provide clocks to DDR and EMAC. With current
dpll settings EMAC doesn't work on radxa rock. EMAC sends packets
to network, but it doesn't receive anything. ifconfig shows a lot
of framing errors.
[1] https://github.com/linux-rockchip/u-boot-rockchip/blob/u-boot-rk3288/
tools/rk_tools/3188_LPDDR2_300MHz_DDR3_300MHz_20130830.bin
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This patch print pl clocks (pl0...pl3) and watchdog
clock using clk dump.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
watchdog clock is also connected to cpu 1X clocksource.
Zynq> clk dump
...
Before:
swdt 4294967290
After:
swdt 111111110
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
add RCC clock driver for STMP32MP157
- base on driver model = UCLASS_CLK
- support ops to enable, disable and get rate
of all SOC clock needed by U-Boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
As said in the SAMA5D2 datasheet, the PLLA clock must be divided
by 2 by writing the PLLADIV2 bit in PMC_MCKR, if the ratio between
PCK and MCK is 3 (MDIV = 3). This is the purpose of the driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
DSI clock is available on STM32F769-disco and
STM32F469-disco board.
Signed-off-by: Yannick Fertre <yannick.fertre@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Implement set_rate() for LTDC clock only, set_rate for other
clocks will be added if needed. This is needed by future LTDC driver
improvements.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Configure SAI PLL configuration to generate LTDC pixel clock on
the PLLSAIR output.
PLLSAI is enabled only if CONFIG_VIDEO_STM32 flag is set.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rework the way SDMMC clock get rate is done in a more
generic way :
_ Add stm32_clk_get_pllsai_rate() which give the PLLSAI
indicated output rate.
_ Add stm32_clk_get_pllsai_vco_rate() which give the VCO
internal rate.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Initially, 48Mhz for SDIO clock was generated from SAI pll for
STM32F469 and STM32F746 SoCs, but this solution was not suitable
for STM32F429 SoCs.
A generic solution is to used the PLL_Q output as 48Mhz clock
for all STM32F SOCs family.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Wrong parameter was passed to stm32_clk_pll48clk_rate().
sysclk (PLL_p output value) was passed instead of VCO value.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
