Currently the pxa3xx driver does not set the udevice in the mtd_info
struct and this prevents the mtd from parsing the partitions via DTS
like for SPI-NOR.
So simply set the mtd->dev to the driver udevice.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
In the case of an erased (sub)page both the data and ECC are all 0xFF
bytes. This fails the normal ECC verification, as the computed ECC of
all-0xFF is not also 0xFF. The GPMC NAND driver attempted to detect
erased pages by checking that the ECC bytes are all-0xFF, but this had
two problems:
1) bitflips in the data were not corrected, so the data looked not-erased
2) bitflips in the ECC bytes were reported as uncorrectable ECC errors
The equivalent Linux driver [1] correctly handles this by counting the
number of 0-bits in the combination of data and ECC bytes. If the number
of 0-bits is less than the amount of bits correctable by the selected
ECC algorithm, then it is treated as an erased page with correctable
bitflips.
Implement similar, though simplified, logic in omap_correct_data_bch().
[1] see omap_elm_correct_data() in omap2.c
Signed-off-by: David Rivshin <drivshin@allworx.com>
Previously, a subpage with an uncorrectable error followed by a subpage
with a correctable error would return an erroneous correctable status.
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The DT properties for the "enable-arbiter" and "keep-config" config
knobs were previously named inconsistently:
- The u-boot driver used "nand-enable-arbiter" and "nand-keep-config"
names, without Marvell prefixes.
- The Linux driver uses "marvell,nand-keep-config" ("enable-arbiter"
does not exist anymore in recent kernels, but it also used to be
"marvell,nand-enable-arbiter").
- The device trees almost all use "marvell," prefixed names, except for
one single instance of "nand-enable-arbiter" without vendor prefix.
This commit standardizes on the vendor prefixed version, making the
u-boot driver read from DT props "marvell,nand-enable-arbiter" and
"marvell,nand-keep-config". The one device tree using the unprefixed
version is also changed to use the new naming.
This has the side effect of making the previously no-op "marvell,"
config knobs already present in some DTs actually do something. This was
likely the original intention of the DT authors, but note that this
commit was not tested on every single impacted board.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
-----BEGIN PGP SIGNATURE-----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=dLEg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20220107' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- disable CONFIG_NET_RANDOM_ETHADDR when unnecessary on amlogic based configs
- meson64_android: add board specific env settings, in order to support VIM3/L for android
- add changes to support VIM3/L android boot by using meson64_android.h config
In order to finish this conversion we need to add a symbols for
SPL_SYS_NAND_SELF_INIT and TPL_SYS_NAND_SELF_INIT as there are cases
there where we need to, or need to not, use that framework as things
stand.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is not used anywhere in the code. Just enable in couple of
defconfigs but it does nothing that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The mt25qu512a supports 4K or 64K sectors, so adding
SECT_4K to enable 4K sector usage.
Tested on Intel n5x hardware with QSPI carrier card
Signed-off-by: Kris Chaplin <kris.chaplin@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
[jagan: droped Tested-by of patch author and datasheet link]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add is25lp512 and is25wp512 devices to spi-nor id table
Tested on Intel n5x hardware with QSPI carrier card
Signed-off-by: Kris Chaplin <kris.chaplin@linux.intel.com>
[jagan: droped Tested-by of patch author]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The original purpose of mtd_erase_callback() in Linux at the time it was
imported to U-Boot, was to inform the caller that erasing is done (since
it was an asynchronous operation).
All supplied callback methods in U-Boot do nothing, but the
mtd_erase_callback() function was (until previous patch) grossly abused
in U-Boot's mtdpart implementation for completely different purpose.
Since we got rid of the abusement, remove the mtd_erase_callback()
function and the .callback member from struct erase_info entirely, in
order to avoid such problems in the future.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The _erase() method of the mtdpart driver, part_erase(), currently
implements offset shifting (for given mtdpart partition) in a weird way:
1. part_erase() adds partition offset to block address
2. parent driver's _erase() method is called
3. parent driver's _erase() method calls mtd_erase_callback()
4. mtd_erase_callback() subtracts partition offset from block address
so that the callback function is given correct address
The problem here is that if the parent's driver does not call
mtd_erase_callback() in some scenario (this was recently a case for
spi_nor_erase(), which did not call mtd_erase_callback() at all), the
offset is not shifted back.
Moreover the code would be more readable if part_erase() not only added
partition offset before calling parent's _erase(), but also subtracted
it back afterwards. Currently the mtd_erase_callback() is expected to do
this subtracting since it does have to do it anyway.
Add the more steps to this procedure:
5. mtd_erase_callback() adds partition offset to block address so that
it returns the the erase_info structure members as it received them
6. part_erase() subtracts partition offset from block address
This makes the code more logical and also prevents errors in case
parent's driver does not call mtd_erase_callback() for some reason.
(BTW, the purpose of mtd_erase_callback() in Linux is to inform the
caller that it is done, since in Linux erasing is done asynchronously.
We are abusing the purpose of mtd_erase_callback() in U-Boot for
completely different purpose. The callback function itself has empty
implementation in all cases in U-Boot.)
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
May it possible to interrupt the spi_nor_erase() function.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The spi_nor_erase() function does not call mtd_erase_callback() as it
should.
The mtdpart code currently implements the subtraction of partition
offset in mtd_erase_callback().
This results in partition offset being added prior calling
spi_nor_erase(), but not subtracted back on return. The result is that
the `mtd erase` command does not erase the whole partition, only some of
it's blocks:
=> mtd erase "Rescue system"
Erasing 0x00000000 ... 0x006fffff (1792 eraseblock(s))
jedec_spi_nor spi-nor@0: at 0x100000, len 4096
jedec_spi_nor spi-nor@0: at 0x201000, len 4096
jedec_spi_nor spi-nor@0: at 0x302000, len 4096
jedec_spi_nor spi-nor@0: at 0x403000, len 4096
jedec_spi_nor spi-nor@0: at 0x504000, len 4096
jedec_spi_nor spi-nor@0: at 0x605000, len 4096
jedec_spi_nor spi-nor@0: at 0x706000, len 4096
This is obviously wrong.
Add proper calling of mtd_erase_callback() into the spi_nor_erase()
function.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
This check is already done in all callers: mtdcore's mtd_write() /
mtd_erase(), legacy spi_nor_write() / spi_flash_erase(). No reason to do
this here as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The cleanup code of spi_nor_erase() function calls write_disable(), but
does not return it's return value even in case of failure. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The cleanup code of the spi_nor_erase() function overwrites the ret
variable with return value of clean_bar(), even if the ret variable is
already set. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The spi_nor_erase() function does not check return value of the
write_enable() call. Fix this.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Use the cleanup codepath of spi_nor_erase() also in the event of failure
of writing the BAR register.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Tested-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The S25FL256L is a part of the S25FL-L family and has the same feature set
as S25FL128L except the density.
The datasheet can be found in the following link.
https://www.cypress.com/file/316171/download
The S25FL256L is 32MB NOR Flash that does not support Bank Address
Register. This fixup is activated if CONFIG_SPI_FLASH_BAR is enabled and
returns ENOTSUPP in setup() hook to avoid further ops.
Tested on Xilinx Zynq-7000 FPGA board.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Add a driver for Macronix raw NAND controller.
This patch referred from linux mxic_nand.c. The difference from the
linux version is described here.
1. In order to adapt to the uboot nand framework, add function
binding (cmdfunc, read_byte, read_buf, write_buf).
2. Added parsing command format to use hardware correctly.
3. Remove the incompatible functions of Uboot.
Signed-off-by: Zhengxun Li <zhengxunli@mxic.com.tw>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
This ID disappeared in 5b66fdb29d ("mtd: spi: Remove unused files"),
add the ID back, since the chip is used on devices supported by U-Boot.
Fixes: 5b66fdb29d ("mtd: spi: Remove unused files")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to datasheet, the upper four bits are reserved or used for
reflecting the ECC status of the accumulated pages. The error bits
number for the worst segment of the current page is encoded on lower
four bits. Fix it by masking the upper bits.
This same issue has been already fixed in the linux kernel by:
"mtd: spinand: macronix: Fix ECC Status Read"
(sha1: f4cb4d7b46f6409382fd981eec9556e1f3c1dc5d)
Apply the same fix in the U-Boot driver.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This converts the CONFIG_STM32_FLASH to Kconfig by using
tools/moveconfig.py
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Since the mxs_nand_spl has implemented adjust read offset in
nand_spl_load_image, so we don't need to check the bad block in
nand_spl_adjust_offset. Directly return the offset to continue
read by nand_spl_load_image.
Signed-off-by: Ye Li <ye.li@nxp.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYVWWZgAKCRDKSWXLKUoM
IY3MAJ43Mlut5tK9gv45bp4HpyVOMuSvJwCfTiVr7ZxrBE8I8QC5+zHzBTmuM6g=
=aQtT
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.01-rc1
zynq:
- Enable capsule update for qspi and mmc
- Update zed DT qspi compatible string
zynqmp:
- Add missing modeboot for EMMC
- Add missing nand DT properties
- List all eeproms for SC on vck190
- Add vck190 SC psu_init
clk:
- Handle only GATE type clock for Versal
watchdog:
- Update versal driver to handle system reset
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Before e2e95e5e25 ("spi: Update speed/mode on change") most systems
silently defaulted to SF bus mode 0. Now the mode is always updated,
which causes breakage. It seems most SF which are used as boot media
operate in bus mode 0, so switch that as the default.
This should fix booting at least on Altera SoCFPGA, ST STM32, Xilinx
ZynqMP, NXP iMX and Rockchip SoCs, which recently ran into trouble
with mode 3. Marvell Kirkwood and Xilinx microblaze need to be checked
as those might need mode 3.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Cc: Andreas Biessmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Siew Chin Lim <elly.siew.chin.lim@intel.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Valentin Longchamp <valentin.longchamp@hitachi-powergrids.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Force the mtd name of spi-nor to "nor" + the driver sequence number:
"nor0", "nor1"... beginning after the existing nor devices.
This patch is coherent with existing "nand" and "spi-nand"
mtd device names.
When CFI MTD NOR device are supported, the spi-nor index is chosen after
the last CFI device defined by CONFIG_SYS_MAX_FLASH_BANKS.
When CONFIG_SYS_MAX_FLASH_BANKS_DETECT is activated, this config
is replaced by to cfi_flash_num_flash_banks in the include file
mtd/cfi_flash.h.
This generic name "nor%d" can be use to identify the mtd spi-nor device
without knowing the real device name or the DT path of the device,
used with API get_mtd_device_nm() and is used in mtdparts command.
This patch also avoids issue when the same NOR device is present 2 times,
for example on STM32MP15F-EV1:
STM32MP> mtd list
SF: Detected mx66l51235l with page size 256 Bytes, erase size 64 KiB, \
total 64 MiB
List of MTD devices:
* nand0
- type: NAND flash
- block size: 0x40000 bytes
- min I/O: 0x1000 bytes
- OOB size: 224 bytes
- OOB available: 118 bytes
- ECC strength: 8 bits
- ECC step size: 512 bytes
- bitflip threshold: 6 bits
- 0x000000000000-0x000040000000 : "nand0"
* mx66l51235l
- device: mx66l51235l@0
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@0
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
* mx66l51235l
- device: mx66l51235l@1
- parent: spi@58003000
- driver: jedec_spi_nor
- path: /soc/spi@58003000/mx66l51235l@1
- type: NOR flash
- block size: 0x10000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000004000000 : "mx66l51235l"
The same mtd name "mx66l51235l" identify the 2 instances
mx66l51235l@0 and mx66l51235l@1.
This patch fixes a ST32CubeProgrammer / stm32prog command issue
with nor0 target on STM32MP157C-EV1 board introduced by
commit b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when
DM is enabled").
Fixes: b7f060565e ("mtd: spi-nor: allow registering multiple MTDs when DM is enabled")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[trini: Add <dm/device.h> to <mtd.h> for DM_MAX_SEQ_STR]
Signed-off-by: Tom Rini <trini@konsulko.com>
nand_dt_init() is still using fdtdec_xx() interface.
If OF_LIVE flag is enabled, dt property can't be get anymore.
Updating all fdtdec_xx() interface to ofnode_xx() to solve this issue.
For doing this, node parameter type must be ofnode.
First idea was to convert "node" parameter to ofnode type inside
nand_dt_init() using offset_to_ofnode(node). But offset_to_ofnode()
is not bijective, in case OF_LIVE flag is enabled, it performs an assert().
So, this leads to update nand_chip struct flash_node field from int to
ofnode and to update all nand_dt_init() callers.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The COFNIG_KEYSTONE_RBL_NAND option is always enabled for the driver on
keystone platforms, but not older davinci platforms. Use def_bool for
the symbol. For CONFIG_KEYSTONE_NAND_MAX_RBL_PAGE, it's only used within
the driver and derived from another symbol, so remove CONFIG from the
name. Finally, CONFIG_KEYSTONE_NAND_MAX_RBL_SIZE is a bit more fixed.
For now, use the value directly. Long term, as part of DM'ifying NAND,
this should come from the device tree.
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the driver st_smic.c used in SPEAr products and the associated
config CONFIG_ST_SMI; this driver is no more used in U-Boot after the
commit 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr
support").
Fixes: 570c3dcfc1 ("arm: Remove spear600 boards and the rest of SPEAr support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This driver uses the CONFIG namespace to set the chips internal CONFIG
namespace related bits. However, CONFIG is reserved for the top-level
Kconfig based configuration system. Use CFG as the namespace here
instead to avoid pollution.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT bindings of "jedec,spi-nor" [1] defines "m25p,fast-read" property
to indicate that "fast read" opcode can be used to read data from the
chip instead of the usual "read" opcode.
If this property is not present in DT, mask out fast read in
spi_nor_init_params(). This change mirrors the same logic in
spi_nor_info_init_params() in drivers/mtd/spi-nor/core.c in
the Linux kernel v5.14-rc3.
[1] Documentation/devicetree/bindings/mtd/jedec,spi-nor.yaml in the kernel tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The smart spi_nor_adjust_hwcaps() does not respect the SPI flash's
hwcaps, and only looks to the controller on what can be supported.
The flash's hwcaps needs to be AND'ed before checking.
Fixes: 71025f013c ("mtd: spi-nor-core: Rework hwcaps selection")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This chip has been (briefly) tested on the MediaTek MT7688 based GARDENA
smart gateway.
Datasheet: http://xmcwh.com/Uploads/2020-12-17/XM25QH64C_Ver1.1.pdf
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The MX25V8035F is a 8Mb SPI NOR flash and the MX25R1635F is very
similar, but has twice the size (16Mb) and supports a wider supply
voltage range.
They were tested on the Kontron Electronics i.MX6UL and i.MX8MM SoMs.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
These boards have not been converted to CONFIG_DM_USB by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the last of the SPEAr platforms, so remove the rest of the remaining
support as well.
Cc: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Define LOG_CATEGORY for all uclass to allow filtering with
log command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fixes mode clocks for SPINOR_OP_READ_FAST_4B in tiny.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The nor->ready() and spansion_sr_ready() introduced earlier in this
series are used for multi-die package parts.
The nor->quad_enable() sets the volatile QE bit on each die.
The nor->erase() is hooked if the device is not configured to uniform
sectors, assuming it has 32 x 4KB sectors overlaid on bottom address.
Other configurations, top and split, are not supported at this point.
Will submit additional patches to support it as needed.
The post_bfpt/sfdp() fixes the params wrongly advertised in SFDP.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cypress chips support SPINOR_OP_EN4B(B7h) to enable 4-byte addressing mode.
Cypress chips support B8h to disable 4-byte addressing mode instead of
SPINOR_OP_EX4B(E9h).
This patch defines new opcode and updates set_4byte() to support
enable/disable 4-byte addressing mode for Cypress chips.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spansion_sr_ready() reads status register 1 by Read Any Register
commnad. This function is called from Flash specific hook with die address
and dummy cycles to support multi-die package parts from Spansion/Cypress.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
For dual/quad die package devices from Spansion/Cypress, the device's
status needs to be checked by reading status registers in all dies, by
using Read Any Register command. To support this, a Flash specific hook
that can overwrite the legacy status check is needed.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support volatile version of configuration
registers and it is recommended to update volatile registers in the field
application due to a risk of the non-volatile registers corruption by
power interrupt. This patch adds a function to set Quad Enable bit in CFR1
volatile.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips support Read/Write Any Register commands.
These commands are mainly used to write volatile registers and access to
the registers in second and subsequent die for multi-die package parts.
The Read Any Register instruction (65h) is followed by register address
and dummy cycles, then the selected register byte is returned.
The Write Any Register instruction (71h) is followed by register address
and register byte to write.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since this flash doesn't have a Profile 1.0 table, the Octal DTR
capabilities are enabled in the post SFDP fixup, along with the 8D-8D-8D
fast read settings.
Enable Octal DTR mode with 20 dummy cycles to allow running at the
maximum supported frequency of 200Mhz.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Cypress Semper flash is an xSPI compliant octal DTR flash. Add
support for using it in octal DTR mode.
The flash by default boots in a hybrid sector mode. Switch to uniform
sector mode on boot. Use the default 20 dummy cycles for a read fast
command.
The SFDP programming on some older versions of the flash was incorrect.
Fixes for that are included in the fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some of Spansion/Cypress chips have overlaid 4KB sectors at top and/or
bottom, depending on the device configuration, while U-Boot supports
uniform sector layout only.
The spansion_erase_non_uniform() erases overlaid 4KB sectors,
non-overlaid portion of normal sector, and remaining normal sectors, by
selecting correct erase command and size based on the address to erase
and size of overlaid portion in parameters. Since different Spansion
flashes can use different opcode for erasing the 4K sectors, the opcode
must be passed in as a parameter based on the flash being used.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
[p.yadav@ti.com: Refactor the function to be compatible with nor->erase,
make 4K opcode customizable, call spi_nor_setup_op() before executing
the op.]
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On devices with non-uniform sector sizes like Spansion S25 or S28 family
of flashes the sector under erase does not necessarily have to be
mtd->erasesize bytes long. For example, on S28 flashes the first 128 KiB
region is composed of 32 4 KiB sectors, then a 128 KiB sector, and then
256 KiB sectors till the end.
Let the flash-specific erase functions erase less than the requested
length in case of the 4 or 128 KiB sectors and report the number of
bytes erased back to the calling function.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
When the flash is handed to us in a stateful mode like 8D-8D-8D, it is
difficult to detect the mode the flash is in. One option is to read SFDP
in all modes and see which one gives the correct "SFDP" signature, but
not all flashes support SFDP in 8D-8D-8D mode.
Further, even if you detect the mode of the flash via SFDP, you still
have the problem of actually reading the ID. The Read ID command is not
standardized across flash vendors. Flashes can have different dummy
cycles needed for reading the ID. Some flashes even expect a 4-byte
dummy address with the Read ID command. All this information cannot be
obtained from the SFDP table.
So, perform a Software Reset sequence before reading the ID and
initializing the flash. A Soft Reset will bring back the flash in its
default protocol mode assuming no non-volatile configuration was set.
This will let us detect the flash even if ROM hands it to us in Octal
DTR mode.
To accommodate cases where there is more than one flash on a board, and
only one of them needs a soft reset, failure to reset is not made fatal,
and we still try to read ID if possible.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
On probe, the SPI NOR core will put a flash in 8D-8D-8D mode if it
supports it. But Linux as of now expects to get the flash in 1S-1S-1S
mode. Handing the flash to Linux in Octal DTR mode means the kernel will
fail to detect the flash.
So, we need to reset to Power-on-Reset (POR) state before handing off
the flash. A Software Reset command can be used to do this.
One limitation of the soft reset is that it will restore state from
non-volatile registers in some flashes. This means that if the flash was
set to 8D mode in a non-volatile configuration, a soft reset won't help.
This commit assumes that we don't set any non-volatile bits anywhere,
and the flash doesn't have any non-volatile Octal DTR mode
configuration.
Since spi-nor-tiny doesn't (and likely shouldn't) have
spi_nor_soft_reset(), add a dummy spi_nor_remove() for it that does
nothing.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A Soft Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.
Find out if the sequence is supported from BFPT DWORD 16.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The Micron MT35XU512ABA flash does not support the quad enable bit. But
instead of programming the Quad Enable Require field to 000b ("Device
does not have a QE bit"), it is programmed to 111b ("Reserved").
While this is technically incorrect, it is not reason enough to abort
BFPT parsing. Instead, continue BFPT parsing assuming there is no quad
enable bit present.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Allow flashes to specify a hook to enable octal DTR mode. Use this hook
whenever possible to get optimal transfer speeds.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The xSPI Profile 1.0 table specifies how many dummy cycles and address
bytes are needed for the Read Status Register command in Octal DTR mode.
Use that information to send the correct Read SR command.
Some controllers might have trouble reading just 1 byte in DTR mode. So,
when we are in DTR mode read 2 bytes and discard the second. This shows
no side effects with the two flashes I tested: Micron mt35xu512aba and
Cypress s28hs512t.
Update Read FSR to mimic Read SR because they share the same
characteristics.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This table is indication that the flash is xSPI compliant and hence
supports octal DTR mode. Extract information like the fast read opcode,
the number of dummy cycles needed for a Read Status Register command,
and the number of address bytes needed for a Read Status Register
command.
The default dummy cycles for a fast octal DTR read are set to 20. Since
there is no simple way of determining the dummy cycles needed for the
fast read command, flashes that use a different value should update it
in their flash-specific hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Some devices in DTR mode expect an extra command byte called the
extension. The extension can either be same as the opcode, bitwise
inverse of the opcode, or another additional byte forming a 16-byte
opcode. Get the extension type from the BFPT. For now, only flashes with
"repeat" and "inverse" extensions are supported.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
JESD216 rev D makes BFPT 20 DWORDs. Update the BFPT size define to
reflect that.
The check for rev A or later compared the BFPT header length with the
maximum BFPT length, BFPT_DWORD_MAX. Since BFPT_DWORD_MAX was 16, and so
was the BFPT length for both rev A and B, this check worked fine. But
now, since BFPT_DWORD_MAX is 20, it means this check will also stop BFPT
parsing for rev A or B, since their length is 16.
So, instead check for BFPT_DWORD_MAX_JESD216 to stop BFPT parsing for
the first JESD216 version, and check for BFPT_DWORD_MAX_JESD216B for the
next two versions.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Double Transfer Rate (DTR) is SPI protocol in which data is transferred
on each clock edge as opposed to on each clock cycle. Make
framework-level changes to allow supporting flashes in DTR mode.
Right now, mixed DTR modes are not supported. So, for example a mode
like 4S-4D-4D will not work. All phases need to be either DTR or STR.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Even when spi_nor_write_reg() has no data to write, like when executing
a write enable operation, it sets the data direction to
SPI_MEM_DATA_OUT. This trips up spi_mem_check_buswidth() because it
expects a data phase when there is none. Make sure the data direction is
set to SPI_MEM_NO_DATA when there is no data to write.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The spi-mem layer provides a spi_mem_supports_op() function to check
whether a specific operation is supported by the controller or not.
This is much more accurate than the hwcaps selection logic based on
SPI_{RX,TX}_ flags.
Rework the hwcaps selection logic to use spi_mem_supports_op().
To make sure the build doesn't break for boards not using CONFIG_DM_SPI,
add a simple SPI_{RX,TX}_ based hwcaps selection logic in spi-mem-nodm
similar to spi_mem_default_supports_op(). This change is only
compile-tested.
To avoid SPL size problems on the x530 board, the old hwcaps selection
is still kept around. Leaving the code in-place was getting difficult to
read and understand, so the code is restructured to have it all in one
isolated function. As a result of this, the parameter hwcaps to
spi_nor_setup() is no longer needed. Remove it.
Based on the Linux commit c76f5089796a (mtd: spi-nor: Rework hwcaps
selection for the spi-mem case, 2019-08-06)
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes the information in a flash's SFDP tables is wrong. Sometimes
some information just can't be expressed in the SFDP table. So,
introduce the fixup hooks to allow tailoring settings for a specific
flash.
Three hooks are added: default_init, post_sfdp, and post_bfpt. These
allow tweaking the flash settings at different point in the probe
sequence. Since the hooks reside in nor->info, set that value just
before the call to spi_nor_init_params().
The hooks and at what points they are executed mimics Linux's spi-nor
framework. One major difference is that Linux puts the struct
spi_nor_fixups in nor->info. This is not possible in U-Boot because the
spi-nor-ids list is shared between spi-nor-core.c and spi-nor-tiny.c.
Since spi-nor-tiny shouldn't have those fixup hooks populated, add a
separate function that lets flashes populate their fixup hooks.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
These structures will be used in a later commit inside another structure
definition. Also take the declarations out of the ifdef since they won't
affect the final binary anyway and will be used in a later commit.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
nor->setup() can be used by flashes to configure settings in case they
have any peculiarities that can't be easily expressed by the generic
spi-nor framework. This includes things like different opcodes, dummy
cycles, page size, uniform/non-uniform sector sizes, etc.
Move related declarations to avoid forward declarations.
Inspired by the Linux kernel's setup() hook.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
If a flash chip has more than 16MB capacity but its BFPT reports
BFPT_DWORD1_ADDRESS_BYTES_3_OR_4, the spi-nor framework defaults to 3.
The check in spi_nor_scan() doesn't catch it because addr_width did get
set. This fixes that check.
Ported from Kernel commit 324f78dfb442b82365548b657ec4e6974c677502.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The get_mtd_device_nm() function (code imported from Linux) simply
iterates all registered MTD devices and compares the given name with
all MTDs' names.
With SPI_FLASH_MTD enabled U-Boot registers a SPI-NOR as a MTD device
with name identical to the SPI flash chip name (from SPI ID table). Thus
for a board with multiple same SPI-NORs it registers multiple MTDs, but
all with the same name (such as "s25fl164k"). We do not want to change
this behaviour, since such a change could break existing boot scripts,
which can rely on a hardcoded name.
In order to allow somehow to uniqely select a MTD device, change
get_mtd_device_nm() function as such:
- if first character of name is '/', try interpreting it as OF path
- otherwise compare the name with MTDs name and MTDs device name.
In the following example a board has two "s25fl164k" SPI-NORs. They both
have name "s25fl164k", thus cannot be uniquely selected via this name.
With this change, the user can select the second SPI-NOR either with
"spi-nor@1" or "/soc/spi@10600/spi-nor@1".
Example:
=> mtd list
List of MTD devices:
* s25fl164k
- device: spi-nor@0
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@0
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
* s25fl164k
- device: spi-nor@1
- parent: spi@10600
- driver: jedec_spi_nor
- path: /soc/spi@10600/spi-nor@1
- type: NOR flash
- block size: 0x1000 bytes
- min I/O: 0x1 bytes
- 0x000000000000-0x000000800000 : "s25fl164k"
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
In order for `mtd list` U-Boot command to list SPI NOR devices without
the need to run `sf probe` before, we have to probe SPI NOR devices in
mtd_probe_devices().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
The device_probe() function does the same thing as mtd_probe() and
mtd_probe() is only used in mtd_probe_uclass_mtd_devs(), where the
probing can be made simpler by using uclass_foreach_dev_probe macro.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Fill in mtd->dev member with nor->dev.
This can be used by MTD OF partition parser.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Currently when the SPI_FLASH_MTD config option is enabled, only one SPI
can be registered as MTD at any time - it is the last one probed (since
with old non-DM model only one SPI NOR could be probed at any time).
When DM is enabled, allow for registering multiple SPI NORs as MTDs by
utilizing the nor->mtd structure, which is filled in by spi_nor_scan
anyway, instead of filling a separate struct mtd_info.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Add support for parsing partitions defined in device-trees via the
`partitions` node with `fixed-partitions` compatible.
The `mtdparts`/`mtdids` mechanism takes precedence. If some partitions
are defined for a MTD device via this mechanism, the code won't register
partitions for that MTD device from OF, even if they are defined.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Macronix NAND Flash devices are available in different configurations
and densities.
MX"35" means SPI NAND
MX35"UF" , UF meands 1.8V
MX35LF"2G" , 2G means 2Gbits
MX35LF2G"E4" , E4 means internal ECC and Quad I/O(x4)
MX35UF4GE4AD/MX35UF2GE4AD/MX35UF1GE4AD are 1.8V 4G/2Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7983/MX35UF4GE4AD,%201.8V,%204Gb,%20v0.00.pdf
MX35UF2GE4AC/MX35UF1GE4AC are 1.8V 2G/1Gbit serial
NAND flash device with 8-bit on-die ECC
https://www.mxic.com.tw/Lists/Datasheet/Attachments/7974/MX35UF2GE4AC,%201.8V,%202Gb,%20v1.0.pdf
Validated via normal(default) and QUAD mode by read, erase, read back,
on Xilinx Zynq PicoZed FPGA board which included Macronix
SPI Host(drivers/spi/spi-mxic.c).
Signed-off-by: Jaime Liao <jaimeliao@mxic.com.tw>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The MX66UW2G345G is Macronix Flash with SINGLE and OCTAL I/O. Hence,
add SPI_NOR_OCTAL_READ flag for this flash.
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: change order of id flags]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: zhengxun <zhengxunli.mxic@gmail.com>
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
use the BBT(bad block table).
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmDLD78cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyLhSB/0UqOd+Ujf2meiHU9yr
oOOCLxVTjTUfIZKLad/zwlj2Xqzsjs6XMawC95BgouvkQLmj/gwerRWcZPg9l7/X
hvb9VJi+iJoLRRpBPbeF3bMb92kCE+YZodFXyutlcY+Z0ZB9755zoVgR6ccKfksd
Xp2y8AFptfYQNZ1l0yb3lhm1261CldWALrGTjRpY2hQ8nEMbV8z6WUB1hAF9CECa
PGbKaiqm9OdktwHsLy4cYFFCuzkykn6T3P6ODineP7IxgEgZKTfJClSTFGY9S0GQ
kwd7K/7j0W3rI5NPknB+Fb4IFAaTs/oozR+5ml7j+2S3G5GXjSGx8zaSOmOZvpP3
KxwN
=/I5V
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.10-a' of https://source.denx.de/u-boot/custodians/u-boot-atmel into next
First set of u-boot-atmel features for the 2021.10 cycle:
This feature set converts the boards pm9261 and pm9263 Ethernet support
to DM; enables hash command for all SAM boards; fixes the NAND pmecc
bit-flips correction; adds Falcon boot for sama5d3_xplained board; and
other minor adjustments.
Not correcting anything in case of empty ECC data area
is not an appropriate strategy, because an uncorrected bit-flip
in an empty sector may cause upper layers (namely UBI) fail to work
properly. Therefore the approach chosen in Linux kernel and other
u-boot mtd drivers has been adopted, where a heuristic implemented
by nand_check_erased_ecc_chunk() is used in order to detect and
correct empty sectors.
Tested with sama5d3_xplained and sam9x60-ek.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
Tested-by: Tudor Ambarus <tudor.ambarus@microchip.com>
[ta: reorder if conditions, change commit subject, s/uint8_t/u8.]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
When apf27_defconfig is built with LTO, linking complains about
undefined reference to `nand_boot`. This is because it is referenced
from inline assembly. Make it visible.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
According to S26KL512S datasheet [1] and S29GL01GS datasheet [2],
the procedure to read out PPB lock bits is to send the PPB Entry,
PPB Read, Reset/ASO Exit. Currently, the code does send incorrect
PPB Entry, PPB Read and Reset/ASO Exit is completely missing.
The PPB Entry sent is implemented by sending flash_unlock_seq()
and flash_write_cmd(..., FLASH_CMD_READ_ID). This translates to
sequence 0x555:0xaa, 0x2aa:0x55, 0x555:0x90=FLASH_CMD_READ_ID.
However, both [1] and [2] specify the last byte of PPB Entry as
0xc0=AMD_CMD_SET_PPB_ENTRY instead of 0x90=FLASH_CMD_READ_ID,
that is 0x555:0xaa, 0x2aa:0x55, 0x555:0xc0=AMD_CMD_SET_PPB_ENTRY.
Since this does make sense, this patch fixes it and thus also
aligns the code in flash_get_size() with flash_real_protect().
The PPB Read returns 00h in case of Protected state and 01h in case
of Unprotected state, according to [1] Note 83 and [2] Note 17, so
invert the result. Moreover, align the arguments with similar code
in flash_real_protect().
Finally, Reset/ASO Exit command should be executed to exit the PPB
mode, so add the missing reset.
[1] https://www.cypress.com/file/213346/download
Document Number: 001-99198 Rev. *M
Table 40. Command Definitions, Nonvolatile Sector Protection
Command Set Definitions
[2] https://www.cypress.com/file/177976/download
Document Number: 001-98285 Rev. *R
Table 7.1 Command Definitions, Nonvolatile Sector Protection
Command Set Definitions
Fixes: 03deff433e ("cfi_flash: Read PPB sector protection from device for AMD/Spansion chips")
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
For all other erase failures, the fail_addr is updated with the
failing address. Only in the case of erase failure due to bad block
detection, the fail_addr is not updated. This change simply updates
the fail_addr for this specific scenario so that it is consistent with
the rest of the code.
Signed-off-by: Farhan Ali <farhan.ali@broadcom.com>
Add a weak nand_get_mtd function for nand drivers to provide mtd info
and use this to set pagesize such that reading of non page-aligned
elements can succeed.
The spl_load_simple_fit already handles block block access so all we
need to do is provide the nand writesize as the block length.
Further cleanup of the drivers which use nand_spl_loaders.c such as
am335x_spl_bch.c, atmel_nand.c, and nand_spl_simple.c could be done
using info from mtd_info instead of statically defined details.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We had a problem detecting 8/16bit flash devices connected only via
8bits to the SoC for quite a while. Commit 239cb9d9
[mtd: cfi_flash: Fix CFI flash driver for 8-bit bus support] finally
fixed this 8-bit bus support. But also broke some other boards using
this cfi driver. So this patch had to be reverted.
I spotted a different, simpler approach for this 8-bit bus support
on the barebox mailing list posted by
Oleksij Rempel <bug-track@fisher-privat.net>:
http://www.spinics.net/lists/u-boot-v2/msg14687.html
Here the commit text:
"
Many cfi chips support 16 and 8 bit modes. Most important
difference is use of so called "Q15/A-1" pin. In 16bit mode this
pin is used for data IO. In 8bit mode, it is an address input
which add one more least significant bit (LSB). In this case
we should shift all adresses by one:
For example 0xaa << 1 = 0x154
"
This patch now is a port of this barebox patch to U-Boot.
Along with the change w.r.t from barebox,
Some flash chips can support multiple bus widths, override the
interface width and limit it to the port width.
Tested on 16-bit Spansion flash on sequoia.
Tested 8-bit flashes like 256M29EW, 512M29EW.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: York Sun <york.sun@nxp.com>
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
This feature was dropped from U-Boot some time ago:
f12f96cfaf (sf: Drop spl_flash_get_sw_write_prot")
However, we do need a way to see if a flash device is write-protected,
since if it is, it may not be possible to write to do (i.e. failing to
write is expected).
I am not sure of the correct layer to implement this, so this patch is a
stab at it. If spi-flash makes sense then I will add to the 'sf' also.
Re the points mentioned in the removal commit:
1) This kind of requirement can be achieved using existing
flash operations and flash locking API calls instead of
making a separate flash API.
Which uclass is this?
2) Technically there is no real hardware user for this API to
use in the source tree.
I do want coral (at least) to support this.
3) Having a flash operations API for simple register read bits
also make difficult to extend the flash operations.
This new patch only mentions write-protect being on or off, rather than
the actual mechanism.
4) Instead of touching generic code, it is possible to have
this functionality inside spinor operations in the form of
flash hooks or fixups for associated flash chips.
That sounds to me like what drivers are for. But we still need some sort
of API for it to be accessible.
Signed-off-by: Simon Glass <sjg@chromium.org>
dfu_free_entities() invoking dfu_free_entity_sf() has let to segementation
faults due to double freeing the same device.
spi_flash_free() is not relevant for the driver model but exists only for
compatibility with old drivers.
We must not remove any device here:
* The device may still be referenced.
* We don't want to have to probe again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Linux commit a75bbe71a27 ("mtd: rawnand: fsl_ifc: fix FSL NAND driver to
read all ONFI parameter pages")
Per ONFI specification (Rev. 4.0), if the CRC of the first parameter page
read is not valid, the host should read redundant parameter page copies.
Fix FSL NAND driver to read the two redundant copies which are mandatory
in the specification.
Signed-off-by: Jane Wan <Jane.Wan@nokia.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Maxim Kochetkov <fido_max@inbox.ru>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
In case of big area read/write on spi nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in spinand_mtd_read() and
spinand_mtd_write() to ensure that watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area erased on nand, watchdog timeout may occurs.
To fix that, add WATCHDOG_RESET() in nanddev_mtd_erase() to ensure that
watchdog is reset.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In case of big area write/erase on spi nor, watchdog timeout may occurs.
Issue reproduced on stm32mp157c-ev1 with following commands:
sf write 0xC0000000 0 0x3000000
or
sf erase 0 0x1000000
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The NOR flash w25q128 denoted by JEDEC ID 0xef4018 actually represents
various models. From Winbond's website, I could only find 3 types of
them:
W25Q128JV-IQ/JQ
datasheet:https://www.winbond.com/resource-files/
w25q128jv%20revg%2004082019%20plus.pdf
W25Q128FV (SPI Mode)
datasheet: https://www.winbond.com/resource-files/
w25q128fv%20rev.m%2005132016%20kms.pdf
W25Q128BV
datesheet: https://www.winbond.com/resource-files/
w25q128bv_revh_100313_wo_automotive.pdf
According to the datasheets, all of these 3 types support BP(0,1,2) and
TB bits in the status register (SR), so it could reuse the flash
protection logic for ST Micro.
So it should be safe to add the SPI_NOR_HAS_LOCK and SPI_NOR_HAS_TB
flags to the w25q128 entry of spi_nor_ids table.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[jagan: remove comments in spi-nor-ids.c]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
ca_do_bch_correction() takes a random value from the stack and starts
counting bitflips from this value. Initialize the counter.
This passed unnoticed as the value is finally ignored in the call
hierarchy.
Fixes: 161df94b3c ("mtd: rawnand: cortina_nand: Add Cortina CAxxxx SoC support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This has no useful meaning in U-Boot and will never be returned. We want
to reserve this flag for internal driver model use.
Drop the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
drivers/mtd/mw_eeprom.c contains code that never worked. mw_eeprom_write()
and mw_eeprom_read() have incorrect loop conditions:
while (len <= 2) {
CONFIG_MW_EEPROM is not set anywhere. So let's simply drop the module.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add Cortina Access parallel Nand support for CAxxxx SOCs
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
CC: Scott Wood <oss@buserror.net>
Reviewed-by: Tom Rini <trini@konsulko.com>
log.h and dm/devres.h are U-Boot includes. So placing them
behind #ifndef __UBOOT__ does not make any sense.
Fixes: f7ae49fc4f ("common: Drop log.h from common header")
Fixes: 61b29b8268 ("dm: core: Require users of devres to include the header")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change pr_* to dev_ or log_ macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
We use the U_BOOT_ prefix (i.e. U_BOOT_DRIVER) to declare a driver but
in every other case we just use DM_. Update the alias macros to use the
DM_ prefix.
We could perhaps rename U_BOOT_DRIVER() to DM_DRIVER(), but this macro
is widely used and there is at least some benefit to indicating it us a
U-Boot driver, particularly for code ported from Linux. So for now, let's
keep that name.
Signed-off-by: Simon Glass <sjg@chromium.org>
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present flags are stored as part of the device. In preparation for
storing them separately, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
The #define of one struct to another has been around for a while. It
confuses dtoc and makes it think that struct spi_flash does not exist.
Make a few changes to improve things while we wait for migration to be
completed:
- Move the 'struct spi_flash' to column 1 so dtoc scans it
- Remove the #define when compiling dt-platdata.c
- Update the strange mtd_get/set_of_node() functions
- Use struct spi_nor in the drivers, so dtoc sees the correct struct
Signed-off-by: Simon Glass <sjg@chromium.org>
This code is a bit odd in that it only reads and updates the livetree
version of the device ofnode. This means it won't work with flattree.
Update the code to work as it was presumably intended.
Signed-off-by: Simon Glass <sjg@chromium.org>
This sort of code does not make much sense:
if (ondie_ecc_enabled) {
if (ondie_ecc_enabled) {
Remove the inner if.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@oktetlabs.ru>
