CONFIG_SPL_FS_EXT4 can be used to include/exclude the FS EXT4 from
SPL build. Excluding the FS EXT4 from SPL build can help to save 20KiB
memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_EXT_SUPPORT to CONFIG_SPLY_FS_EXT4 so both
obj-$(CONFIG_$(SPL_)FS_EXT4) and CONFIG_IS_ENABLED(FS_EXT4) can be
used to control the build in both SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Most of the time SPL only needs very simple FAT reading, so having
CONFIG_IS_ENABLED(FAT_WRITE) to exclude it from SPL build would help
to save 64KiB default max clustersize from memory.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This fixes CVE-2018-18440 ("insufficient boundary checks in filesystem
image load") by using lmb to check the load size of a file against
reserved memory addresses.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This particular commit is causing a regression on stih410-b2260 and
other platforms when reading from FAT16. Noting that I had rebased the
original fix from Thomas onto then-current master, there is also
question from Akashi-san if the change is still needed after other FAT
fixes that have gone in.
This reverts commit a68b0e11ea.
Reported-by: Patrice Chotard <patrice.chotard@st.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
Signed-off-by: Tom Rini <trini@konsulko.com>
The call to file_cbfs_fill_cache() is given with the parameter
'start' pointing to the offset by the CBFS base address, but
with the parameter 'size' that equals to the whole CBFS size.
During CBFS walking through, it checks files one by one and
after it pass over the end of the CBFS which is 4GiB boundary
it tries to check files from address 0 and so on, until the
overall size the codes checked hits to the given 'size'.
Fix this by passing 'start' pointing to the CBFS base address.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
cbfs_fileheader.len indicates the content size of the file in the
cbfs, and it has nothing to do with cbfs_fileheader.offset which
is the starting address of the file in the cbfs.
Remove such check in file_cbfs_next_file(). Before this change
'cbfsinit' failed with 'Bad CBFS file'. After this change all cbfs
commands are working as expected.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
[bmeng: keep the necessary header sanity check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The long name apparently can be accumulated using multiple
13-byte slots. Unfortunately we never checked how many we
can actually fit in the buffer we are reading to.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
The cluster size specifies how many sectors make up a cluster. A
cluster size of zero makes no sense, as it would mean that the
cluster is made up of no sectors. This will later lead into a
division by zero in sect_to_clust(), so better take care of that
early.
The MAX_CLUSTSIZE define can reduced using a define to make some
room in low-memory system. Unfortunately if the code reads a
filesystem with a bigger cluster size it will overflow the buffer.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
As in the case of fs_set_blk_dev(), fs_set_blk_dev_with_part() should
maintain and update fs_dev_part whenever called.
Without this patch, a problem will come up when an efi binary associated
with efi's BOOTxxxx variable is invoked via "bootefi bootmgr".
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This fixes problems accessing drives formated under
Windows as FAT16.
Signed-off-by: Thomas RIENOESSL <thomas.rienoessl@bachmann.info>
[trini: Rebase on top of f528c140c8]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add fs.c under SPL as well as it is needed for fs_loader
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Add as obj-$(CONFIG_FS_LOADER) for non-SPL_FRAMEWORK builds]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add local size_t variable to crypto_comp_decompress as intermediate
storage for destination length to avoid memory corruption and incorrect
results on 64 bit targets.
This is what linux does for the various lz compression implementations.
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Cc: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
As observed with clang:
fs/fat/fat_write.c:1024:13: warning: comparison of constant 128
with expression of type 'char' is always false
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~~~~ ^ ~
fs/fat/fat_write.c:1024:25: warning: comparison of constant 255
with expression of type 'char' is always true
[-Wtautological-constant-out-of-range-compare]
if ((0x80 <= c) && (c <= 0xff))
~ ^ ~~~~
Fixes: 25bb9dab14 ("fs: fat: check and normalize file name")
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
When traversing slots in a btree (via btrfs_path) with btrfs_next_slot(),
we didn't correctly identify that the last slot in the leaf was reached
and we should jump to the next leaf.
This could lead to any kind of runtime errors or corruptions, like:
* file data not being read at all, or is read partially
* file is read but is corrupted
* (any) metadata being corrupted or not read at all, etc
The easiest way to reproduce this is to read a large enough file that
its EXTENT_DATA items don't fit into a single leaf.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
Avoid CoverityScan warning SIGN_EXTENSION by changing the type of
parameter size of set_cluster().
Avoid leaking stack content when writing an incomplete last sector.
Reported-by: Coverity (CID: 184096)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Do not leak filename_copy in case of error.
Catch out of memory when calling strdup.
Reported-by: Coverity (CID: 184086)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The btrfs implementation passes cache-unaligned buffers into the
block layer, which triggers cache alignment problems down in the
block device drivers. Align the buffers to prevent this.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Behun <marek.behun@nic.cz>
The FAT driver supports unaligned reads and writes and EFI applications
will make use of these. So a misaligned buffer is only worth a debug
message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, unlink support is added to FAT file system.
A directory can be deleted only if it is empty.
In this implementation, only a directory entry for a short file name
will be removed. So entries for a long file name can and should be
reclaimed with fsck.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"unlink" interface is added to file operations.
This is a preparatory change as unlink support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, mkdir support is added to FAT file system.
A newly created directory contains only "." and ".." entries.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The starting cluster number of directory is needed to initialize ".."
(parent directory) entry when creating a new directory.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
"mkdir" interface is added to file operations.
This is a preparatory change as mkdir support for FAT file system
will be added in next patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, all the necessary code for allowing for a file offset
at write is implemented. What plays a major roll here is get_set_cluster(),
which, in contrast to its counterpart, set_cluster(), only operates on
already-allocated clusters, overwriting with data.
So, with a file offset specified, set_contents() seeks and writes data
with set_get_cluster() until the end of a file, and, once it reaches
there, continues writing with set_cluster() for the rest.
Please note that a file will be trimmed as a result of write operation if
write ends before reaching file's end. This is an intended behavior
in order to maintain compatibility with the current interface.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The current write implementation is quite simple: remove existing clusters
and then allocating new ones and filling them with data. This, inevitably,
enforces always writing from the beginning of a file.
As the first step to lift this restriction, fat_file_write() and
set_contents() are modified to accept an additional parameter, file offset
and further re-factored so that, in the next patch, all the necessary code
will be put into set_contents().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In this patch, write implementation is overhauled and rewritten by
making full use of directory iterator. The obvious bonus is that we are
now able to write to a file with a directory path, like /A/B/C/FILE.
Please note that, as there is no notion of "current directory" on u-boot,
a file name specified must contain an absolute directory path. Otherwise,
"/" (root directory) is assumed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
It would be good that FAT write function return error code instead of
just returning -1 as fat_read_file() does.
This patch attempts to address this issue although it is 'best effort
(or estimate)' for now.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT file system's long file name support is a bit complicated and has some
restrictions on its naming. We should be careful about it especially for
write as it may easily end up with wrong file system.
normalize_longname() check for the rules and normalize a file name
if necessary. Please note, however, that this function is yet to be
extended to fully comply with the standard.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
This reverts commit 0dc1bfb730.
The succeeding patch series will supersede it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
In my attempt to re-work write operation, it was revealed that iterator's
"clust" does not always point to a cluster to which a current directory
entry ("dent") belongs.
This patch assures that it is always true by adding "next_clust" which is
used solely for dereferencing a cluster chain.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
FAT's root directory does not have "." nor ".."
So care must be taken when scanning root directory with fat_itr_resolve().
Without this patch, any file path starting with "." or ".." will not be
resolved at all.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
get_fs_info() was introduced in major re-work of read operation by Rob.
We want to reuse this function in write operation by extending it with
additional members in fsdata structure.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
I just stumbled over some cluttered UBIFS messages. It seems some
newline chars are missing in the current U-Boot UBI source.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In order to make the debug print in file_fat_read_at() a tad more useful,
show the offset the file is being read at alongside the filename.
Suggested-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fs_fat_write() is not able to write to subdirectories.
Currently if a filepath with a leading slash is passed, the slash is
treated as part of the filename to be created in the root directory.
Strip leading (back-)slashes.
Check that the remaining filename does not contain any illegal characters
(<>:"/\|?*). This way we will throw an error when trying to write to a
subdirectory.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The comparison
logical > item->logical + item->length
in btrfs_map_logical_to_physical is wrong and should be instead
logical >= item->logical + item->length
For example, if
item->logical = 4096
item->length = 4096
and we are looking for logical = 8192, it is not part of item (item is
[4096, 8191]). But the comparison is false and we think we have found
the correct item, although we should be searing in the right subtree.
This fixes some bugs I encountered.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
By checking ubifs source code, s_instances parameter is not
used anymore. So, set this parameter and the associated source
code under __UBOOT__ compilation.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This is the case when reading freshly created filesystem.
The error message is like the following:
btrfs_read_superblock: No valid root_backup found!
Since the data from super_roots/root_backups is not actually used -
decided to rework btrfs_newest_root_backup() into
btrfs_check_super_roots() that will only check if super_roots
array is valid and correctly handle empty scenario.
As a result:
* btrfs_read_superblock() now only checks if super_roots array is valid;
the case when it is empty is considered OK.
* removed root_backup pointer from btrfs_info,
which would be NULL in case of empty super_roots.
* btrfs_read_superblock() verifies number of devices from the superblock
itself, not newest root_backup.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
This causes errors when translating logical addresses to physical:
btrfs_map_logical_to_physical: Cannot map logical address <addr> to physical
btrfs_file_read: Error reading extent
The behavior of btrfs_map_logical_to_physical() is to stop traversing
CHUNK_TREE when it encounters first non-CHUNK_ITEM, which makes
only some portion of CHUNK_ITEMs being read.
Change it to skip over non-chunk items.
Signed-off-by: Yevgeny Popovych <yevgenyp@pointgrab.com>
Cc: Marek Behun <marek.behun@nic.cz>
Cc: Sergey Struzh <sergeys@pointgrab.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Add fs_get_type_name so we can get the current filesystem type.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Found a crash while issuing ext4ls with a non-existent directory.
Crash test:
=> ext4ls mmc 0 1
** Can not find directory. **
data abort
pc : [<3fd7c2ec>] lr : [<3fd93ed8>]
reloc pc : [<26f142ec>] lr : [<26f2bed8>]
sp : 3f963338 ip : 3fdc3dc4 fp : 3fd6b370
r10: 00000004 r9 : 3f967ec0 r8 : 3f96db68
r7 : 3fdc99b4 r6 : 00000000 r5 : 3f96dc88 r4 : 3fdcbc8c
r3 : fffffffa r2 : 00000000 r1 : 3f96e0bc r0 : 00000002
Flags: nZCv IRQs off FIQs off Mode SVC_32
Resetting CPU ...
resetting ...
Tested on SAMA5D2_Xplained board (sama5d2_xplained_mmc_defconfig)
Looks like crash is introduced by commit:
"fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Issue is that dirnode is not initialized, and then freed if the call
to ext4_ls fails. ext4_ls will not change the value of dirnode in this case
thus we have a crash with data abort.
I added initialization and a check for dirname being NULL.
Fixes: "fa9ca8a" fs/ext4/ext4fs.c: Free dirnode in error path of ext4fs_ls
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch solves assert failed displayed in the console during a boot.
The root cause is that the ubifs_inode is not already allocated when
ubifs_printdir and ubifs_finddir functions are called.
Trace showing the issue:
feed 'boot.scr.uimg', ino 94, new f_pos 0x17b40ece
dent->ch.sqnum '7132', creat_sqnum 3886945402880
UBIFS assert failed in ubifs_finddir at 436
INODE ALLOCATION: creat_sqnum '7129'
Found U-Boot script /boot.scr.uimg
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The mutex lock and unlock functions are stubbed out and mutex_is_locked
was 0. This caused asserts to fail in ubifs code when checking that the
mutex was locked. For example,
UBIFS assert failed in ubifs_change_lp at 540
UBIFS assert failed in ubifs_release_lprops at 278
Assume that the "mutex" is locked since that is the normal case when it
is checked in the ubifs code.
Signed-off-by: Bradley Bolen <bradleybolen@gmail.com>
Introduce another difference from upstream (kernel) source in
fs/ubifs/super.c: adding preprocessor condition as y variable in
mount_ubifs() depends on CONFIG_UBIFS_SILENCE_MSG:
fs/ubifs/super.c:1337:15: error: variable ?y? set but not used [-Werror=unused-but-set-variable]
long long x, y;
Not setting CONFIG_UBIFS_SILENCE_MSG in am335x_igep003x_defconfig and
igep0032_defconfig. Although it was defined in their config headers, it
depends on CMD_UBIFS which is not set for them.
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Use of CONFIG_UBIFS_SILENCE_MSG was added in
147162dac6 ("ubi: ubifs: Turn off verbose prints")
Then it was removed in
ff94bc40af ("mtd, ubi, ubifs: resync with Linux-3.14")
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Petr Vorel <petr.vorel@gmail.com>
When printing a size_t value we need to use %zu for portability between
32bit and 64bit targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Loading files stored with lzo compression from a btrfs filesystem was
producing unaligned memory accesses, which were causing a data abort
and a reset on an Orange Pi Zero.
The change in hash.c is not triggered by any error but follows the
same pattern. Please confirm.
Fixed according to doc/README.unaligned-memory-access.txt
Signed-off-by: Alberto Sánchez Molero <alsamolero@gmail.com>
Tested-by: Robert Nelson <robertcnelson@gmail.com>
fat.h unconditionally defines CONFIG_SUPPORT_VFAT (and has done since
2003), so as a result VFAT support is always enabled regardless of
whether a board config defines it or not. Drop this unnecessary option.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The message "reading %s\n" may be interesting when
debugging but otherwise it is superfluous.
Only output the message when debugging.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The message
"** %s shorter than offset + len **\n"
may be interesting when debugging but it does not indicate an
error.
So we should not write it if we are not in debug mode.
Fixes: 7a3e70cfd8 fs/fs.c: read up to EOF when len would read past EOF
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
commit 21a24c3bf3 ("fs/fat: fix case for FAT shortnames") made it
possible that get_name() returns file names with some upper cases.
find_directory_entry() must be updated to take this account, and use
case-insensitive functions to compare file names.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This header was renamed to rawnand.h in Linux.
The following is the corresponding commit in Linux.
commit d4092d76a4a4e57b65910899948a83cc8646c5a5
Author: Boris Brezillon <boris.brezillon@free-electrons.com>
Date: Fri Aug 4 17:29:10 2017 +0200
mtd: nand: Rename nand.h into rawnand.h
We are planning to share more code between different NAND based
devices (SPI NAND, OneNAND and raw NANDs), but before doing that
we need to move the existing include/linux/mtd/nand.h file into
include/linux/mtd/rawnand.h so we can later create a nand.h header
containing all common structure and function prototypes.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Before this patch one could receive following errors when executing "fatls"
command on machine with cache enabled (ex i.MX6Q) :
=> fatls mmc 0:1
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
CACHE: Misaligned operation at range [4f59dfc8, 4f59e7c8]
ERROR: v7_outer_cache_inval_range - start address is not aligned - 0x4f59dfc8
ERROR: v7_outer_cache_inval_range - stop address is not aligned - 0x4f59e7c8
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Fixes: 09fa964bba ("fs/fat: Fix 'CACHE: Misaligned operation at range' warnings")
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
It is unwise to first dereference a variable
and then to check if it was NULL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The iterator variable of list_for_each is never NULL.
if (1 || A) is always true.
Use break if entry found.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Some fixes when reading EXT files and directory entries were identified
after using e2fuzz to corrupt an EXT3 filesystem:
- Stop reading directory entries if the offset becomes badly aligned.
- Avoid overwriting memory by clamping the length used to zero the buffer
in ext4fs_read_file. Also sanity check blocksize.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: Stefano Babic <sbabic@denx.de>
All users of this macro have been converted. Remove MTDDEBUG and
related CONFIG options.
ubifs_dbg_msg_key() is kept. It is silent unless DEBUG is defined.
I am not touching scripts/config_whitelist.txt. The deprecated options
will be dropped by the next resync.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This makes gcc no longer expect an out-of-line version of the
functions being present elsewhere.
This fixes a failure to build on several marvell targets with gcc-7 on
Debian:
https://bugs.debian.org/877963
Signed-off-by: Adrian Bunk <bunk@debian.org>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Hello,
I ran into a problem with the JFFS2 filesystem driver implemented in U-Boot.
I've got a NAND device that has correctable ECC errors (corrected somewhere in mtd/nand/nand_base.c).
The NAND driver tells the filesystem layer (jffs2_1pass.c) above that there occurred correctable ECC errors and returns with a "value > 0".
The JFFS2 driver recognizes the corrected ECC errors as real error and skips this block because the only accepts a "return value == 0" as correct.
This problem exists for over 8 years (I checked version 2010.09) so I'm a little bit worried that I interpreted something wrong or didn't get the whole context.
Can someone confirm this bug (and the bugfix) in the u-boot jffs2 driver?
There was a mail in 2012 that mentioned the same problem, but there was no patch:
http://u-boot.10912.n7.nabble.com/JFFS2-seems-to-drop-nand-data-with-ECC-corrections-td142008.html
Sometime after this discussion the return value of nand_read() changed from -EUCLEAN as correctable ECC error to a positive value with the count of ECC corrected errors.
With kind reguards,
Uwe Engling
The variable res should be initialized to 0 in these functions,
because if the searched key is not found, the variable is used
uninitialized.
Reported-by: Coverity (CID: 167335)
Reported-by: Coverity (CID: 167336)
Reported-by: Coverity (CID: 167337)
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Check malloc() return values and properly unwind on errors so
memory allocated for fat_itr structures get freed properly.
Also fixes a leak of fsdata.fatbuf in fat_size().
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Reported-by: Coverity (CID: 167225, 167233, 167234)
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The 'block' field of fat_itr needs to be properly aligned for DMA and
while it does have '__aligned(ARCH_DMA_MINALIGN)', the fat_itr structure
itself needs to be properly aligned as well.
While at it use malloc_cache_aligned() for the other aligned allocations
in the file as well.
Fixes: 2460098cff ("fs/fat: Reduce stack usage")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
As reported by Coverity, we did not free dirnode in the case of failure.
Do so now.
Reported-by: Coverity (CID: 131221)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
If we end up back in the root directory via a '..' directory entry, set
itr->is_root accordingly. Failing to do that gives spews like
"Invalid FAT entry" and being unable to access directory entries located
past the first cluster of the root directory.
Fixes: 8eafae209c ("fat/fs: convert to directory iterators")
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
The current code doesn't compute the group descriptor checksum correctly
for the filesystems that e2fsprogs 1.43.4 creates (they have
'Group descriptor size: 64' as reported by tune2fs). Extend the checksum
calculation to be done as ext4_group_desc_csum() does in Linux.
This fixes these errors in dmesg from running fs-test.sh and makes it
succeed again:
[1671902.620699] EXT4-fs (loop1): ext4_check_descriptors: Checksum for group 0 failed (35782!=10965)
[1671902.620706] EXT4-fs (loop1): group descriptors corrupted!
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds the proper implementation for the BTRFS filesystem.
The implementation currently supports only read-only mode and
the filesystem can be only on a single device.
Checksums of data chunks is unimplemented.
Compression is implemented (ZLIB + LZO).
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/btrfs.h
create mode 100644 fs/btrfs/chunk-map.c
create mode 100644 fs/btrfs/compression.c
create mode 100644 fs/btrfs/ctree.c
create mode 100644 fs/btrfs/dev.c
create mode 100644 fs/btrfs/dir-item.c
create mode 100644 fs/btrfs/extent-io.c
create mode 100644 fs/btrfs/hash.c
create mode 100644 fs/btrfs/inode.c
create mode 100644 fs/btrfs/root.c
create mode 100644 fs/btrfs/subvolume.c
create mode 100644 fs/btrfs/super.c
BTRFS on disk structures are stored in Little Endian. Add functions
to convert this structures to cpu and to disk format.
On Little Endian hosts, these functions do nothing.
On Big Endian the CALL_MACRO_FROM_EACH from variadic-macro.h is used
to define all the members for each structure on which cpu_to_le* or
le*_to_cpu is to be called.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/conv-funcs.h
Add btrfs_tree.h and ctree.h from Linux which contains constants
and structures for the BTRFS filesystem.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 fs/btrfs/btrfs_tree.h
create mode 100644 fs/btrfs/ctree.h
The ext4, reiserfs and zfs filesystems all have their own implementation
of the same function, *_devread. Generalize this function into fs_devread
and put the code into fs/fs_internal.c.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
[trini: Move fs/fs_internal.o hunk to the end of fs/Makefile as all
cases need it]
Signed-off-by: Tom Rini <trini@konsulko.com>
We have limited stack in SPL builds. Drop itrblock and move to
malloc/free of itr to move this off of the stack. As part of this fix a
double-free issue in fat_size().
Signed-off-by: Tom Rini <trini@konsulko.com>
---
Rework to use malloc/free as moving this to a global overflows some SH
targets.
A new fatbuf was allocated by get_fs_info() (called by fat_itr_root()),
but not freed, resulting in eventually running out of memory. Spotted
by running 'ls -r' in a large FAT filesystem from Shell.efi.
fatbuf is mainly used to cache FAT entry lookups (get_fatent())..
possibly once fat_write.c it can move into the iterator to simplify
this.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Use the clust_to_sect() helper that was introduced earlier, and add an
inverse sect_to_clust(), plus update the various spots that open-coded
this conversion previously.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Noticed when comparing our output to linux. There are some lcase bits
which control whether filename and/or extension should be downcase'd.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a generic implementation of 'ls' using opendir/readdir/closedir, and
replace fat's custom implementation. Other filesystems should move to
the generic implementation after they add opendir/readdir/closedir
support.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Spotted by chance, when trying to remove file_fat_ls(), I noticed there
were some dead users of the API.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Acked-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement the readdir interface using the directory iterators.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Needed to support efi file protocol. The fallback.efi loader wants
to be able to read the contents of the /EFI directory to find an OS
to boot.
Modelled after POSIX opendir()/readdir()/closedir(). Unlike the other
fs APIs, this is stateful (ie. state is held in the FS_DIR "directory
stream"), to avoid re-traversing of the directory structure at each
step. The directory stream must be released with closedir() when it
is no longer needed.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
And drop a whole lot of ugly code!
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Untangle directory traversal into a simple iterator, to replace the
existing multi-purpose do_fat_read_at() + get_dentfromdir().
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Want to re-use this in fat dirent iterator in next patch.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
While &p_jdb[fs->blksz] is a valid expression (it points *one* char
sized element past the end of the array, e.g. &p_jdb[fs->blksz + 1] is
invalid (according to the C standard (C99/C11)).
Changing this to tag = (struct ext3_journal_block_tag *)(p_jdb + ofs);
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Suggested-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 165117, 165110)
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The overflow calculation was incorrect. Adding the start block of the
partition is not needed because the sectors are already relative to the
beginning of the partition. If you attempted to write a file smaller
than cur_part_info.start blocks on a full partition the old calculation
fails to catch the overflow. This would cause an infinite loop in the
determine_fatent function.
Old, incorrect calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = partition start + total sectors on the partition
Adding the partition start block number is not needed because sectors
are already relative to the start of the partition.
New calculation:
ending sector of new file = start sector + file size (in sectors)
last sector = total sectors on the partition
Signed-off-by: Reno Farnesi <nfarnesi4@gmail.com>
The function blk_dread will return -ENOSYS on failure or on success the
number of blocks read, which must be the number asked to read (otherwise
it failed somewhere). Correct this check.
Signed-off-by: Tom Rini <trini@konsulko.com>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_YAFFS2
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch fixes the below warning by typecasting it properly
fs/ubifs/ubifs.c: In function 'ubifs_load':
fs/ubifs/ubifs.c:942:29: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
err = ubifs_read(filename, (void *)addr, 0, size, &actread);
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add Kconfig symbols for various configurations
supported by FAT filesystem support code.
CONFIG_SUPPORT_VFAT has been left out since its
force enabled in include/fat.h and probably
should get removed at some point.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
[trini: add select FS_FAT for CMD_FAT and SPL_FAT_SUPPORT]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_JFFS2 for both the filesystem and its command, we
should have a separate option for each. This allows us to enable JFFS2
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than using CMD_CRAMFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CRAMFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CRAMFS for keymile]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than using CMD_CBFS for both the filesystem and its command, we
should have a separate option for each. This allows us to enable CBFS
support without the command, if desired, which reduces U-Boot's size
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: imply FS_CBFS on SYS_COREBOOT]
Signed-off-by: Tom Rini <trini@konsulko.com>
In file ext4fs.c funtion ext4fs_read_file() compares an
unsigned expression with < 0 like below
lbaint_t blknr;
blknr = read_allocated_block(&(node->inode), i);
if (blknr < 0)
return -1;
blknr is of type ulong/uint64_t. read_allocated_block() returns
long int. So comparing blknr with < 0 will always be false. Instead
declare blknr as long int.
Similarly ext4/dev.c does a similar comparison. Drop the redundant
comparison.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If !parent, the changed line is not reached.
So there is no need to check the value again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Handle symlinks to files in the current directory. Other cases could be
handled with additional code, but this is a start.
Add explicit errors for absolute paths and links found in the middle of
a path (directories). Other cases like '..' or '.' will result with the
file not being found as when those path components are explicitly
provided.
Add a helper to decompress a null-terminated link name which is shared
with cramfs_list_inode.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Using a variably-sized type is incorrect here since we're reading a
fixed file format. Fixes cramfs on 64-bit platforms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Doing unaligned reads is not supported on all architectures, use
byte sized reads of the little endian buffer.
Rename off16 to off8, as it reflects the buffer offset in byte
granularity (offset is in entry, i.e. 12 bit, granularity).
Fix a regression introduced in 8d48c92b45
Reported-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
We convert CONFIG_PARTITION_UUIDS to Kconfig first. But in order to cleanly
update all of the config files we must also update CMD_PART and CMD_GPT to also
be in Kconfig in order to avoid complex logic elsewhere to update all of the
config files.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
genext2fs creates revision level 0 filesystems, which are not readable
by u-boot due to the initialized group descriptor size field.
f798b1dda1
Reported-by: Kever Yang <kever.yang@rock-chips.com>
Reported-by: FrostyBytes@protonmail.com
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Instead of shuffling bits from two adjacent 16 bit words, use one 16 bit
word with the appropriate byte offset in the buffer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
get_fatent_value(...) flushes changed FAT entries to disk when fetching
the next FAT blocks, in every other aspect it is identical to
get_fatent(...).
Provide a stub implementation for flush_dirty_fat_buffer if
CONFIG_FAT_WRITE is not set. Calling flush_dirty_fat_buffer during read
only operation is fine as it checks if any buffers needs flushing.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
The FAT is read/flushed in segments of 6 (FATBUFBLOCKS) disk sectors. The
last segment may be less than 6 sectors, cap the length.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
The u-boot command fatwrite empties FAT clusters from the beginning
till the end of the file.
Specifically for FAT12 it fails to detect the end of the file and goes
beyond the file bounds thus corrupting the file system.
Additionally, FAT entry chaining-up into a file is not implemented
for FAT12.
The users normally workaround this by re-formatting the partition as
FAT16/FAT32, like here:
https://github.com/FEDEVEL/openrex-uboot-v2015.10/issues/1
The patch fixes the bounds of a file and FAT12 entries chaining into
a file, including EOF markup.
Signed-off-by: Philipp Skadorov <philipp.skadorov@savoirfairelinux.com>
Now that we free resources in sandbox_fs_ls Coverity is letting us know
that in some cases we might leak. So in case of error we should still
let os_dirent_free free anything that was allocated.
Fixes: 86167089b7 ("sandbox/fs: Free memory allocated by os_dirent_ls")
Reported-by: Coverity (CID: 153450)
Cc: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fill_dir_slot use get_contents_vfatname_block as a temporary buffer for
constructing a list of dir_slot entries. To save the memory and providing
correct type of memory for above usage, a local buffer with accurate size
declaration is introduced.
The local array size 640 is used because for long file name entry,
each entry use 32 bytes, one entry can store up to 13 characters.
The maximum number of entry possible is 20. So, total size is
32*20=640bytes.
Signed-off-by: Genevieve Chan <ccheauya@altera.com>
Signed-off-by: Tien Fong Chee <tfchee@altera.com>
Support was already implemented, but not hooked up. This fixes several
fails in the test cases.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
A sparse file may have regions not mapped by any extents, at the start
or at the end of the file, or anywhere between, thus not finding a
matching extent region is never an error.
Found by python filesystem tests.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Instead of creating a journal entry for each directory block, even
if the block is unmodified, only log the modified block.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
The direntlen checks were quite bogus, i.e. the loop termination used
"len + offset == blocksize" (exact match only), and checked for a
direntlen less than 0. The latter can never happen as the len is
unsigned, this has been reported by Coverity, CID 153384.
Use the same code as in search_dir for directory traversal. This code
has the correct checks for direntlen >= sizeof(struct dirent), and
offset < blocksize.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reported-by: Coverity (CID: 153383, 153384)
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Use the same variable names as in search_dir, to make purpose of variables
more obvious.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
We are supposed to use #include <...> to include headers in the
public include paths. We should use #include "..." only for headers
in local directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable mounting of ext4 fs with 64bit feature, as it is supported now.
These had been disabled in 6f94ab6656.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The descriptor size is variable, thus array indices are not generically
applicable. The larger group descriptors also contain e.g. high parts
of block numbers, which have to be read and written.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The correct descriptor size must be used when calculating offsets, and
also to read the correct amount of data.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The helper functions encapsulate access of the block group descriptors,
independent of group descriptor size. The helpers also deal with the
endianess of the fields, and with split fields like free_blocks/
free_blocks_high.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
If EXT4_FEATURE_INCOMPAT_64BIT is set, the descriptor can be read from
the superblocks, otherwise it defaults to 32.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
If the same block is updated multiple times in a row during a single
file system operation, gd_index is decremented to use the same journal
entry again. Avoid loosing the already allocated buffer.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
read_allocated block may return block number 0, which is just an indicator
a chunk of the file is not backed by a block, i.e. it is sparse.
During file deletions, just continue with the next logical block, for other
operations treat blocknumber <= 0 as an error.
For writes, blocknumber 0 should never happen, as U-Boot always allocates
blocks for the whole file. Reading already handles this correctly, i.e. the
read buffer is 0-fillled.
Not treating block 0 as sparse block leads to FS corruption, e.g.
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /2.5GB.file 1 '
The 2.5GB.file from the fs test is actually a sparse file.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The data blocks are identical for files using traditional direct/indirect
block allocation scheme and extent trees, thus this code part can be
common. Only the code to deallocate the indirect blocks to record the
used blocks has to be seperate, respectively the code to release extent
tree index blocks.
Actually the code to release the extent tree index blocks is still missing,
but at least add a FIXME at the appropriate place.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Make sure the the extra_isize field (offset 128) is initialized to 0, to
mark any extra data as invalid.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
fs->inodesz is already correctly (i.e. dependent on fs revision)
initialized in ext4fs_mount.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
temp_ptr should always be freed, even if the function is left via
goto fail.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
If the blocksize is 1024, count is initialized with 1. Incrementing count
by 8 will never match (count == fs->blksz * 8), and ptr may be
incremented beyond the buffer end if the bitmap is filled. Add the
startblock offset after the loop.
Remove the second loop, as only the first iteration will be done.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
The last free block of a block group may be in its middle. After it has
been allocated, the next block group should be scanned from its beginning.
The following command triggers the bad behaviour (on a blocksize 1024 fs):
./sandbox/u-boot -c 'i=0; host bind 0 ./disk.raw ;
while test $i -lt 260 ; do echo $i; setexpr i $i + 1;
ext4write host 0:2 0 /X${i} 0x1450; done ;
ext4write host 0:2 0 /X240 0x2000 ; '
When 'X240' is extended from 5200 byte to 8192 byte, the new blocks should
start from the first free block (8811), but it uses the blocks 8098-8103
and 16296-16297 -- 8103 + 1 + 8192 = 16296. This can be shown with
debugfs, commands 'ffb' and 'stat X240'.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
zero_buffer is never written, thus clearing it is pointless.
journal_buffer is completely initialized by ext4fs_devread (or in case
of failure, not used).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
e2fsck warns about "Group descriptor 0 marked uninitialized without
feature set."
The bg_itable_unused field is only defined if FEATURE_RO_COMPAT_GDT_CSUM
is set, and should be set (kept) zero otherwise.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Scanning only the direct blocks of the directory file may falsely report
an existing file as nonexisting, and worse can also lead to creation
of a duplicate entry on file creation.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
While directories can be read using the old linear scan method, adding a
new file would require updating the index tree (alternatively, the whole
tree could be removed).
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Previously, only the last directory block was scanned for available space.
Instead, scan all blocks back to front, and if no sufficient space is
found, eventually append a new block.
Blocks are only appended if the directory does not use extents or the new
block would require insertion of indirect blocks, as the old code does.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
The following command crashes u-boot:
./sandbox/u-boot -c 'i=0; host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
while test $i -lt 200 ; do echo $i; setexpr i $i + 1;
ext4write host 0 0 /foobar${i} 0; done'
Previously, the code updated the direct_block even for extents, and
fortunately crashed before pushing garbage to the disk.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
In case the dir entry creation failed, ext4fs_write would later overwrite
a random inode, as inodeno was never initialized.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
The following command triggers a segfault in search_dir:
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /./foo 0x10'
The following command triggers a segfault in check_filename:
./sandbox/u-boot -c 'host bind 0 ./sandbox/test/fs/3GB.ext4.img ;
ext4write host 0 0 /. 0x10'
"." is the first entry in the directory, thus previous_dir is NULL. The
whole previous_dir block in search_dir seems to be a bad copy from
check_filename(...). As the changed data is not written to disk, the
statement is mostly harmless, save the possible NULL-ptr reference.
Typically a file is unlinked by extending the direntlen of the previous
entry. If the entry is the first entry in the directory block, it is
invalidated by setting inode=0.
The inode==0 case is hard to trigger without crafted filesystems. It only
hits if the first entry in a directory block is deleted and later a lookup
for the entry (by name) is done.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
All fields were accessed directly instead of using the proper byte swap
functions. Thus, ext4 write support was only usable on little-endian
architectures. Fix this.
Signed-off-by: Michael Walle <michael@walle.cc>
Change all the types of ext2/4 fields to little endian types and all the
JBD fields to big endian types. Now we can use sparse (make C=1) to check
for statements where we need byteswaps.
Signed-off-by: Michael Walle <michael@walle.cc>
Current description does not match the function behaviour.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
The code caches 6 sectors of the FAT. On FAT traversal, the old contents
needs to be flushed to disk, but only if any FAT entries had been modified.
Explicitly flag the buffer on modification.
Currently, creating a new file traverses the whole FAT up to the first
free cluster and rewrites the on-disk blocks.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
fatlength is a local variable which is no more used after the assignment.
s_name is not used in the function, save the strncpy.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
This fixes incorrect filenames in cbfsls output.
Signed-off-by: Yaroslav K. <yar444@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[clean up checkpatch errors and warnings]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With e2fsprogs after 1.43 the 64bit and metadata_csum features are
enabled by default. The metadata_csum feature changes how
ext4_group_desc->bg_checksum is calculated, which would break write
support. The 64bit feature however introduces changes such that it
cannot be read by implementations that do not support it. Since we do
not support this, we must not mount it.
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reported-by: Andrew Bradford <andrew.bradford@kodakalaris.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix the following build errors when building sandbox on x86 32-bit:
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:364:7: error: conflicting types for 'memset'
void* memset(void*, int, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:78:15: note: previous declaration of 'memset' was here
extern void * memset(void *,int,__kernel_size_t);
^
In file included from fs/cbfs/cbfs.c:8:0:
include/malloc.h:365:7: error: conflicting types for 'memcpy'
void* memcpy(void*, const void*, size_t);
^
In file included from include/compiler.h:123:0,
from include/cbfs.h:10,
from fs/cbfs/cbfs.c:7:
include/linux/string.h:81:15: note: previous declaration of 'memcpy' was here
extern void * memcpy(void *,const void *,__kernel_size_t);
^
scripts/Makefile.build:280: recipe for target 'fs/cbfs/cbfs.o' failed
Signed-off-by: Guillaume GARDET <guillaume.gardet@free.fr>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions are part of the Linux 4.6 sync. They are being added
before the main sync patch in order to make it easier to address the
issue across all NAND drivers (many/most of which do not closely track
their Linux counterparts) separately from other merge issues.
Signed-off-by: Scott Wood <oss@buserror.net>
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.
This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip. It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].
Signed-off-by: Scott Wood <oss@buserror.net>
This option currently enables both the command and the SCSI functionality.
Rename the existing option to CONFIG_SCSI since most of the code relates
to the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
The function ext4fs_read_symlink was unable to handle a symlink
which had target name of exactly 60 characters.
Signed-off-by: Ronald Zachariah <rozachar@cisco.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Tom Rini <trini@konsulko.com>
In list "super_blocks" ubifs collects allocated super_block
structs. U-Boot frees on unmount the allocated struct,
so the pointer stored in this list is free after the umount.
On a new ubifs mount, the new allocated super_block struct
get inserted into the super_blocks list ... which contains
now a freed pointer, and the list_add_tail() corrupts the
freed memory ...
2 solutions are possible:
- remove the super_block from the super_blocks list
on umount
- as U-Boot does not use the super_blocks list ...
remove it complete for U-Boot.
Both solutions should not introduce problems for porting
to newer linux version, so this patch removes the unused
super_blocks list, as it saves code size and execution
time.
Signed-off-by: Heiko Schocher <hs@denx.de>
We only use 'ofs' in jffs2_sum_scan_sumnode when debugging as it's part
of a dbg_summary call. Mark this as __maybe_unused.
Signed-off-by: Tom Rini <trini@konsulko.com>
To ease conversion to driver model, add helper functions which deal with
calling each block device method. With driver model we can reimplement these
functions with the same arguments.
Use inline functions to avoid increasing code size on some boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
This is a device number, and we want to use 'dev' to mean a driver model
device. Rename the member.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename three partition functions so that they start with part_. This makes
it clear what they relate to.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Rename this function to blk_get_device_part_str(). This is a better name
because it makes it clear that the function returns a block device and
parses a string.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Use 'struct' instead of a typdef. Also since 'struct block_dev_desc' is long
and causes 80-column violations, rename it to struct blk_desc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
As noted by Coverity, when we have an error in
alloc_triple_indirect_block we will leak ti_pbuff_start_addr as it's not
being freed. Further inspection here shows that we could also leak
ti_cbuff_start_addr in one corner case so free that as well.
Reported-by: Coverity (CID 131205, 131206)
Signed-off-by: Tom Rini <trini@konsulko.com>
This will allow the implementation to make use of data in the block_dev
structure beyond the base device number. This will be useful so that eMMC
block devices can encompass the HW partition ID rather than treating this
out-of-band. Equally, the existence of the priv field is crying out for
this patch to exist.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
If the ext3 journal gets out of sync with what is written on disk, for
example because of an unexpected power cut, ext4fs_read_file can
return an all-zero directory entry. In that case, ext4fs_iterate_dir
would infinite loop.
This patch detects when a directory entry's direntlen member is 0 and
returns a failure status, which breaks out of the infinite loop. As a
result, U-Boot will not find files that may subsequently be recovered
when the journal is replayed.
This is better behaviour than hanging in an infinite loop, but as a
further improvement maybe U-Boot could interpret the ext3 journal and
actually find the unsynced entries.
Signed-off-by: Thomas Fitzsimmons <fitzsim@cisco.com>
Reviewed-by: Stefan Roese <sr@denx.de>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
sync with linux v4.2
commit 64291f7db5bd8150a74ad2036f1037e6a0428df2
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Aug 30 11:34:09 2015 -0700
Linux 4.2
This update is needed, as it turned out, that fastmap
was in experimental/broken state in kernel v3.15, which
was the last base for U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Tested-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Add generic fs support, so that commands like ls, load and test -e can be
used on ubifs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Implement the necessary functions for implementing generic fs support
for ubifs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Modify the ubifs u-boot wrapper function prototypes for generic fs use,
and give them their own header file.
This is a preparation patch for adding ubifs support to the generic fs
code from fs/fs.c.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Overwriting an empty file not created by U-Boot did not work, and it
could even corrupt the FAT. Moreover, creating empty files or emptying
existing files allocated a cluster, which is not standard.
Fix this by always keeping empty files clusterless as specified by
Microsoft (the start cluster must be set to 0 in the directory entry in
that case), and by supporting overwriting such files.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
curclust was used instead of newclust in the debug() calls and in one
CHECK_CLUST() call, which could skip a failure case.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
set_contents() had uselessly split calls to set_cluster(). Merge these
calls, which removes some cases of set_cluster() being called with a
size of zero.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
set_cluster() was using a temporary buffer without enforcing its
alignment for DMA and cache. Moreover, it did not check the alignment of
the passed buffer, which can come directly from applicative code or from
the user.
This could cause random data corruption, which has been observed on
i.MX25 writing to an SD card.
Fix this by only passing ARCH_DMA_MINALIGN-aligned buffers to
disk_write(), which requires the introduction of a buffer bouncing
mechanism for the misaligned buffers passed to set_cluster().
By the way, improve the handling of the corresponding return values from
disk_write():
- print them with debug() in case of error,
- consider that there is an error is disk_write() returns a smaller
block count than the requested one, not only if its return value is
negative.
After this change, set_cluster() and get_cluster() are almost
symmetrical.
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
