timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
timer support
interrupt controller support
flash support
ethernet support
cache support
board information support
env support
booting image support
adding support for Xilinx ML401
The AMCC Luan now uses the common 440SP(e) DDR SPD code for DDR
inititializition. This includes DDR auto calibration and support
for different DIMM modules, instead of the fixed setup used in
the earlier version.
This patch also enables the cache in FLASH for the startup
phase of U-Boot (while running from FLASH). After relocating to
SDRAM the cache is disabled again. This will speed up the boot
process, especially the SDRAM setup, since there are some loops
for memory testing (auto calibration).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem that occurs when 2 DIMM's are
used. This problem was first spotted and fixed by Gerald Jackson
<gerald.jackson@reaonixsecurity.com> but this patch fixes the
problem in a little more clever way.
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
As this feature is new to the "old" 44x SPD DDR driver, it
has to be enabled via the CONFIG_PROG_SDRAM_TLB define.
Signed-off-by: Stefan Roese <sr@denx.de>
The config value for:
* CFG_ACR_PIPE_DEP
* CFG_ACR_RPTCNT
* CFG_SPCR_TSEC1EP
* CFG_SPCR_TSEC2EP
* CFG_SCCR_TSEC1CM
* CFG_SCCR_TSEC2CM
Were not being used when setting the appropriate register
Added:
* CFG_SCCR_USBMPHCM
* CFG_SCCR_USBDRCM
* CFG_SCCR_PCICM
* CFG_SCCR_ENCCM
To allow full config of the SCCR.
Also removed random CFG_SCCR settings in MPC8349EMDS, TQM834x, and sbc8349
that were just bogus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, this patch
updates ftp_cpu_setup() to write the MAC address to mac-address if it exists.
This function already updates local-mac-address.
Signed-off-by: Timur Tabi <timur@freescale.com>
The code supply fixed and SPD initialization for MPC83xx DDR2 Controller.
it pass DDR/DDR2 compliance tests.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8360E rev2.0 have new spridr,and PVR value,
The MDS board for MPC8360E rev2.0 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
MPC8349E rev3.1 have new spridr,and PVR value,
The MDS board for MPC8349E rev3.1 has 32M bytes Flash and 256M DDR2 DIMM.
Signed-off-by: Xie Xiaobo<X.Xie@freescale.com>
The code that is ifdef'd with CONFIG_MPC8349 is actually applicable to all
MPC834X class processors. Change the protections from CONFIG_MPC8349 to
CONFIG_MPC834X so they are more generic.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
I've redone the SBC8349 support to match git-current, which
incorporates all the MPC834x updates from Freescale since the 1.1.6
release, including the DDR changes.
I've kept all the SBC8349 files as parallel as possible to the
MPC8349EMDS ones for ease of maintenance and to allow for easy
inspection of what was changed to support this board. Hence the SBC8349
U-Boot has FDT support and everything else that the MPC8349EMDS has.
Fortunately the Freescale updates added support for boards using CS0,
but I had to change spd_sdram.c to allow for board specific settings for
the sdram_clk_cntl (it is/was hard coded to zero, and that remains the
default if the board doesn't specify a value.)
Hopefully this should be mergeable as-is and require no whitespace
cleanups or similar, but if something doesn't measure up then let me
know and I'll fix it.
Thanks,
Paul.
Put the version (and magic) after the HRCW. This puts it in a fixed
location in flash, not at the start of flash but as close as we can get.
Signed-off-by: Jerry Van Baren <vanbaren@cideas.com>
For better format and style, I streamlined the 83xx head files,
including immap_83xx.h and mpc83xx.h. In the old head files, 1)
duplicated macro definition appear in the both files; 2) the structure
of QE immr is duplicated in the immap_83xx.h and immap_qe.h; 3) The
macro definition put inside the each structure. So, I cleaned up the
structure of QE immr from immap_83xx.h, deleted the duplicated stuff and
moved the macro definition to mpc83xx.h, Just like MPC8260.
CHANGELOG
*streamline the 83xx immr head file
Signed-off-by: Dave Liu <daveliu@freescale.com>
This patch updates the recently added Katmai board support. The biggest
change is the support of ECC DIMM modules in the 440SP(e) SPD DDR2
driver.
Please note, that still some problems are left with some memory
configurations. See the driver for more details.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the DDR2 controller used on the
440SP and 440SPe. It is tested on the Katmai (440SPe) eval
board and works fine with the following DIMM modules:
- Corsair CM2X512-5400C4 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5/512 (512MByte per DIMM)
- Kingston ValueRAM KVR667D2N5K2/2G (1GByte per DIMM)
This patch also adds the nice functionality to dynamically
create the TLB entries for the SDRAM (tlb.c). So we should
never run into such problems with wrong (too short) TLB
initialization again on these platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the existing 4xx SPD SDRAM initialization routines for the
405 SDRAM controller and the 440 DDR controller don't have much in
common this patch splits both drivers into different files.
This is in preparation for the 440 DDR2 controller support (440SP/e).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for multiple I2C busses on the PPC4xx
platforms. Define CONFIG_I2C_MULTI_BUS in the board config file
to make use of this feature.
It also merges the 405 and 440 i2c header files into one common
file 4xx_i2c.h.
Also the 4xx i2c reset procedure is reworked since I experienced
some problems with the first access on the 440SPe Katmai board.
Signed-off-by: Stefan Roese <sr@denx.de>
Block device read/write is anonymous data; there is no need to use a
typed pointer. void * is fine. Also add a hook for block_read functions
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each of the filesystem drivers duplicate the get_dev routine. This change
merges them into a single function in part.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Previously the strapping DCR/SDR was read to determine if the internal PCI
arbiter is enabled or not. This strapping bit can be overridden, so now
the current status is read from the correct DCR/SDR register.
Signed-off-by: Stefan Roese <sr@denx.de>
Conflicts:
drivers/cfi_flash.c
The patch by Heiko Schocher <hs@pollux.denx.de> on Jan, 19, 2007
fixes cfi_driver bug for mpc7448hpc2 board. The default cfi_driver can support
mpc7448hpc2 board.
This patch fixes a problem with an incorrect setup for the refresh
timer of the 44x DDR controller in the file cpu/ppc4xx/sdram.c
Signed-off-by: Stefan Roese <sr@denx.de>
This code will optimize the DDR2 controller setup on a board specific
basis.
Note: This code doesn't work right now on the NAND booting image for the
Sequoia board, since it doesn't fit into the 4kBytes for the SPL image.
Signed-off-by: Stefan Roese <sr@denx.de>
multiplier table can not refect the real PLL clock behavior of these
processors. Please refer to the hardware specification for detailed
information of the corresponding processors.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The original search_one_table() function code can only processes the search
for the exception occurring in FLASH/ROM, because the exception and fixup
table usually locate in FLASH. If the exception address is also in
FLASH, it will be OK.
If the exception occurs in RAM, after the u-boot relocation, a
relocation offset should be added.
clean up the code in cpu/74xx_7xx/cpu.c
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The conflicts due to a new mpc7448 p3m7448 board is in the main tree.
Merge branch 'master' into hpc2
Conflicts:
MAKEALL
cpu/74xx_7xx/cpu.c
cpu/74xx_7xx/cpu_init.c
cpu/74xx_7xx/speed.c
(1) remove some C++ comments.
(2) remove trailing white space.
(3) remove trailing empty line.
(4) Indentation by table.
(5) remove {} in one line condition.
(6) add space before '(' in function call.
Remove some weird printf () output.
Add necessary comments.
Modified Makefile to support building in a separate directory.
The soc node of the mpc52xx needs to be loaded with the IPB bus frequency,
not the XLB frequency.
This patch depends on the previous patches for MPC52xx device tree support
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
This patch adds support for the Prodrive P3M750 (PPC750 & MV64460)
and the P3M7448 (MPC7448 & MV64460) PMC modules. Both modules are
quite similar and share the same board directory "prodrive/p3mx"
and the same config file "p3mx.h".
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the code and configuration necessary to boot with an
arch/powerpc Linux kernel.
Signed-off-by: Grant Likely <grant.likely@gmail.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Patch below corrects the setting of the zmiifer register, it was
overwritting the register rather than ORing the settings.
Signed-off-by: Neil Wilson <NWilson@airspan.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Fixed cpu/ppc4xx/start.S for 440EPx Errata: further corrects PPC440EPx
errata 1.12: 440_33 by moving patch up in code.
Signed-off-by: Jeff Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
