- Let am335x_evm use the CPSW or PRUSS ethernet.
- Implement timer_get_boot_us in the omap timer driver
- gpmc bitflip, QSPI clock calculation on am437x, da8xx_gpio bugfixes
- Assorted K3 updates
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmHlNOccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyL0JB/4+sKNWPMgOYvP2uLCC
euRGomhxJ5WmxJVDtJeBIRg0YKSkwnE8JwIN2qqGu15xJnNX9Ck5qnIMPbiZ/io9
ocW5Z/4C4rfJX/OzD6FtmbMNsvG/umVmZkjRU3ryRXKGyNVpVjLQ2EEECaJfk1WZ
Nd/J6/Jo8nafb1x4OeY+F6+xwZAuj7Mrun9SsDSyrIvmEqSnaQNioj+lStkauL51
NwQgBxZBQmbdCgF7Ooy6rYlXZBR6r/rgWB9n3RP8emDCwfCMul9HOMT432oKNbhW
bGrcMu9AWv/pgzXogxSzYbEdTAnoVEODtU1suCa8LV6KJPEG693gARnRm/KjvPHa
FfsK
=39IY
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 features for the 2022.04 cycle:
This small feature set includes few changes for sama7g5 and sama7g5ek:
turn blue led on at boot, changes required for the Rev4 of the board,
better sync with the Linux DT with regards to the new DT nodes.
CONFIG_PHANDLE_CHECK_SEQ will allow different sequence number for nodes
that have the same name, but they are different.
In sama7g5ek case, there are multiple 'i2c@600' nodes which are child
nodes of different parent 'flexcom' nodes.
These are different i2c busses even if the node is the same, and have to be
differentiated.
Without this config, the sequence number 0 is reused for two i2c busses, and
this is something that we have to avoid:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
Looking for 'i2c' at 6236, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
Found seq 0
i2c_post_bind: i2c@600, seq=0
After this patch:
Looking for 'i2c' at 4704, name i2c@600
- serial0, /ahb/apb/serial@e1824200
- i2c0, /ahb/apb/flexcom@e181c000/i2c@600
- i2c1, /ahb/apb/flexcom@e2818000/i2c@600
Found seq 1
Before the patch:
=> i2c bus
Bus 0: i2c@600
Bus 0: i2c@600 (active 0)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
=>
After the patch:
=> i2c bus
Bus 0: i2c@600
Bus 1: i2c@600 (active 1)
52: eeprom@52, offset len 1, flags 0
53: eeprom@53, offset len 1, flags 0
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The rev4 of the board sama7g5ek has the eeproms on flexcom8 instead of
flexcom1.
Initialize flexcom8 with required pincontrol and move the eeproms accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add Flexcom8 node with required referenced nodes as phandles.
Since Flexcom8 is present in Linux, take the node exactly as-is from Linux.
Some nodes are referenced in Linux as phandles, the dma and the gic.
Add them as well to the file, even if they are unused by Uboot.
This is a step towards having the U-boot DT equivalent with the DT in Linux.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This driver supports power domains for the power management
controller found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These are necessary to make sure the power domains needed for the
serial console are availble in the pre-relocation phase.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This synchronizes the device trees with those that are in the
process of being upstreamed into Linux. This is mostly the
current state of the device trees on the asahilinux branch
with a few extra bits used by OpenBSD. This includes device
trees for machines that were still missing.
There are still some differences that will hopefully be resolved
soon.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The am335x-ice-v2 board's Ethernet ports can be configured
in 'MII' or 'RMII' mode to be connected to 'PRUSS' or 'CPSW'
Ethernet subsystems.
This patch sets the environment variable 'ice_mii' to
'mii' or 'rmii' accordingly. Based on that we choose the
appropriate board devicetree i.e. 'am335x-ice-v2.dtb' or
'am335x-ice-v2-prueth.dtb'.
Since there are 2 Ethernet ports with 2 modes, there can be 4
configurations but for now we consider both ports in different modes
to be an invalid configuration and prevent boot in that case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Amjad: use overlay instead of using new am335x-ice-v2-prueth.dtb]
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Make prueth_is_mii be marked __maybe_unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
In the case of an erased (sub)page both the data and ECC are all 0xFF
bytes. This fails the normal ECC verification, as the computed ECC of
all-0xFF is not also 0xFF. The GPMC NAND driver attempted to detect
erased pages by checking that the ECC bytes are all-0xFF, but this had
two problems:
1) bitflips in the data were not corrected, so the data looked not-erased
2) bitflips in the ECC bytes were reported as uncorrectable ECC errors
The equivalent Linux driver [1] correctly handles this by counting the
number of 0-bits in the combination of data and ECC bytes. If the number
of 0-bits is less than the amount of bits correctable by the selected
ECC algorithm, then it is treated as an erased page with correctable
bitflips.
Implement similar, though simplified, logic in omap_correct_data_bch().
[1] see omap_elm_correct_data() in omap2.c
Signed-off-by: David Rivshin <drivshin@allworx.com>
On AM4372 the SPI_GCLK input gets its clock from the PRCM module which
divides the PER_CLKOUTM2 frequency (192MHz) by a fixed factor of 4.
See AM437x Reference Manual in section 27 QSPI >> 27.2 Integration.
The QSPI_FCLK therefore needs to take this factor into account and
becomes (192000000 / 4).
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
To make the OMAP DM timer driver useful for the timing of
bootstages, we need to implement timer_get_boot_us(..).
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The GPIO bank numbers do not appear in the device tree,
so make the gpio name based on the address
(ie gpio@42110000_25 vs 25)
Signed-off-by: chao zeng <chao.zeng@siemens.com>
The fastboot protocol uses per default the UDP port 5554. In some cases
it might be needed to change the used port. The fastboot utility provides
a way to specifiy an other port number to use already.
fastboot -s udp:192.168.1.76:1234 boot fastboot.img
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
NXP's mEMAC reference manual, Chapter 6.5.5 "MDIO Ethernet Management
Interface usage", specifies to poll the BSY (0) bit in the CFG/STAT
register to wait until a transaction has finished, not bit 31 in the
data register.
In the Linux kernel, this has already been fixed in commit 26eee0210ad7
("net/fsl: fix a bug in xgmac_mdio").
This patch changes the register in the fman_mdio and fsl_ls_mdio
drivers.
As the MDIO_DATA_BSY define is no longer in use, this patch also removes
its definition from the fsl_memac header.
Signed-off-by: Markus Koch <markus@notsyncing.net>
Reviewed-by: Camelia Groza <camelia.groza@nxp.com>
Reduce the missing phy-handle log message to debug message. It is
possible for ethernet DT node to have no phy-handle e.g. in case
of a fixed-link connection. Furthermore, drop the FEC: prefix,
which is a copy-paste error and rather print the ethernet device
name.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This driver is based on an older downstream TI kernel, with
changes and cleanups to work with mainline device-tree bindings.
Signed-off-by: Dominic Rath <rath@ibv-augsburg.net>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The sja1105_check_device_id() function contains logic to work without
changing the device tree on reworked boards, one of which I have (the
NXP LS1021A-TSN normally has a SJA1105T, but I have a version with a
resoldered SJA1105Q which is pin compatible). This logic is taken from
the Linux driver.
However this logic gets shortcircuited in U-Boot by an earlier check for
the exact device ID specified in the device tree. So the reworked board
does not probe the SJA1105Q switch. Remove this duplicated logic and let
the automatic device ID detection do its job.
Fixes: f24b666b22 ("net: dsa: add driver for NXP SJA1105 L2 switch")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the DSA API is going to allow drivers to do things such as:
- phy_config in dsa_ops :: port_probe
- phy_startup in dsa_ops :: port_enable
then it would actually be good if the ->port_probe() method would
actually be called in all cases before the ->port_enable() is.
Currently this is true for user ports, but not true for the CPU port,
because the CPU port does not have a udevice registered for it (this is
all part of DSA's design). So the current issue is that after
phy_startup has finished for the CPU port, its phydev->speed is an
uninitialized value, because phy_config() was never called for the
priv->cpu_port_fixed_phy, and it is precisely phy_config() who copies
the speed into the phydev in the case of the fixed PHY driver.
So we need to simulate a probing event for the CPU port by manually
calling the driver's ->port_probe() method for the CPU port.
Fixes: 8a2982574854 ("net: dsa: introduce a .port_probe() method in struct dsa_ops")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This will allow consumers to choose a pxe label at runtime instead of
having to prompt the user. One good use-case for this, is choosing
whether or not to apply a dtbo depending on the hardware configuration.
e.g: for TI's AM335x EVM, it would be convenient to apply a particular
dtbo only when the J9 jumper is on PRUSS mode. To achieve this, the
pxe menu should have 2 labels, one with the dtbo and the other without,
then the "pxe_label_override" env variable should point to the label with
the dtbo at runtime only when the jumper is on PRUSS mode.
This change can be used for different use-cases and bring more
flexibilty to consumers who use sysboot/pxe_utils.
if "pxe_label_override" is set but does not exist in the pxe menu,
the code should fallback to the default label if given, and no failure
is returned but rather a warning message.
Signed-off-by: Amjad Ouled-Ameur <aouledameur@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Artem Lapkin <email2tema@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Call dram_init_banksize() from spl_board_init() otherwise TFTP download
fails due to lmb_get_free_size() not able to find unreserved region due
to lack of DRAM size info. Required to support Ethernet boot on AM64x.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
On certain TI SoC, like AM64x there is a CPSW3G which supports 2
external independent MAC ports for single CPSW instance.
It is not possible for Ethernet driver to register more than one port
for given instance.
This patch modifies top level CPSW NUSS as UCLASS_MISC and binds
UCLASS_ETH to individual ports so as to support bring up more than one
Ethernet interface in U-Boot.
Note that there is no isolation in the since, CPSW NUSS is in promisc
mode and forwards all packets to host.
Since top level driver is now UCLASS_MISC, board files would need to
instantiate this driver explicitly.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Probe toplevel AM65 CPSW NUSS driver from misc_init_r() when driver
is enabled. Since driver is modeled as UCLASS_MISC, we need to
explicitly probe the driver. Use common misc_init_r() that entire
K3 family of SoCs.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Driver has a bug in that it uses rflow_in_use bitmap when setting up free rflow range
from TISCI but use rflow_map for reservation in __udma_reserve_rflow()
Fix this by dropping rflow_in_use bitmap array and use rflow_map for
PKTDMA. BCDMA does not need rflow_in_use either.
This fixes CPSW3g not able to get DMA channels at R5 SPL on AM64x
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
In case of xSPI bootmode OSPI flash is in DDR mode and needs to be accessed
in multiple of 16bit accesses Hence we cannot parse sysfw.itb FIT image
directly on OSPI flash via MMIO window. So, copy the image to internal
on-chip RAM before parsing the image.
Moreover, board cfg data maybe modified by ROM/TIFS in case of HS platform
and thus cannot reside in OSPI/xSPI and needs to be copied over to
internal OCRAM.
This unblocks OSPI/xSPI boot on HS platforms
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
Currently only the PADCFG registers of the main domain are unlocked.
Also unlock PADCFG registers of MCU domain, so MCU pin muxing can be configured by u-boot or Linux.
Signed-off-by: Michael Liebert <liebert@ibv-augsburg.de>
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
-----BEGIN PGP SIGNATURE-----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=NZ+6
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-04-rc1
Documentation:
* Fix building HTML documentation of readthedocs.io
* Add ARM Juno board documentation
* Build requirements for Alpine Linux
* Include DM headers in API documentation
UEFI:
* Fix section alignment of EFI binaries
* Fix header length of RISC-V EFI binaries allowing to run them on EDK II
* Remove kaslr-seed from device tree if the EFI_RNG_PROTOCOL is provided
Other:
* Let 'part list' show all 128 GPT partitions
- A number of fixes in various subsystems. This includes having the phy
uclass track power-on and init counts as this should resolve some
tricky functional problems on a number of platforms.
Document the return value in efi_init(). Fix up @sizep in efi_info_get().
Use Return: instead of @return
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present some 32-bit settings are used with the 64-bit app. Fix this by
separating out the two cases.
Be careful not to break the 64-bit payload, which needs to build a 64-bit
EFI stub with a 32-bit U-Boot.
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
That script is not intended for use with EFI, so update the logic to avoid
using it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Christian Melki <christian.melki@t2data.com>
Add an empty CPU init function to avoid fiddling with low-level CPU
features in the app. Set up the C runtime correctly for 64-bit use
and avoid clearing BSS, since this is done by EFI when U-Boot is loaded.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the 'efi' command only works in the EFI payload. Update it to
work in the app too, so the memory map can be examined.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present this function requires a pointer to struct efi_entry_memmap
but the only field used in there is the desc_size. We want to be able
to use it from the app, so update it to use desc_size directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this code is inline in the app and stub. But they do the same
thing. The difference is that the stub does it immediately and the app
doesn't want to do it until the end (when it boots a kernel) or not at
all, if returning to UEFI.
Move it into a function so it can be called as needed.
Add a comment showing how to store the memory map so that it can be
accessed within the app if needed, for debugging purposes only. The map
can change without notice.
Signed-off-by: Simon Glass <sjg@chromium.org>
If variable dfu_alt_info is not defined duplicate messages are displayed.
=> efidebug boot dump
Scanning disk mmc2.blk...
Scanning disk mmc1.blk...
Scanning disk mmc0.blk...
Found 3 disks
No EFI system partition
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
"dfu_alt_info" env variable not defined!
Probably dfu_alt_info not defined
Remove the 'Probably dfu_alt_info not defined' message.
Instead write a warning if the variable contains no entities.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
U-Boot, in some occasions, injects a 'kaslr-seed' property on the /chosen
node. That would be problematic in case we want to measure the DTB we
install in the configuration table, since it would change across reboots.
The Linux kernel EFI-stub completely ignores it and only relies on
EFI_RNG_PROTOCOL for it's own randomness needs (i.e the randomization
of the physical placement of the kernel). In fact it (blindly) overwrites
the existing seed if the protocol is installed. However it still uses it
for randomizing it's virtual placement.
So let's get rid of it in the presence of the RNG protocol.
It's worth noting that TPMs also provide an RNG. So if we tweak our
EFI_RNG_PROTOCOL slightly and install the protocol when a TPM device
is present the 'kaslr-seed' property will always be removed, allowing
us to reliably measure our DTB.
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
A GPT partition table typically has 128 entries. If a partition table
contains a partition 128 'part list' should be able to list it.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
For GPT partition tables the 'part list' command stops at the first invalid
partition number. But Ubuntu has images with partitions number
1, 12, 13, 14, 15
In this case only partition 1 was listed by 'part list'.
Fixes: 38a3021edc ("disk: part_efi: remove indent level from loop")
Reported-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
The alignment of sections in the EFI binaries generated by U-Boot is
incorrect.
According to the PE-COFF specification [1] the minimum value for
FileAlignment is 512. If the value of SectionAlignment is
less then the page size, it must equal FileAlignment.
Let's set both values to 512 for the ARM and RISC-V architectures.
[1] https://docs.microsoft.com/en-us/windows/win32/debug/pe-format
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
EDK II refuses to load the EFI binaries created by U-Boot.
The reason is an incorrect PE-COFF header. The number of
data directories does not match NumberOfRvaAndSizes.
This leads to a failed consistency check in
PeCoffLoaderGetPeHeader():
SizeOfOptionalHeader - HeaderWithoutDataDir) !=
NumberOfRvaAndSizes * sizeof(DATA_DIRECTORY))
Fixes: 9afaeec6ef ("riscv: Complete efi header for RV32/64")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
