leandrof/u-boot
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity
master
u-boot/configs/verdin-imx8mm_defconfig

146 lines
3.5 KiB
Plaintext
Raw Permalink Normal View History

board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_ARM=y
CONFIG_ARCH_IMX8M=y
Rename CONFIG_SYS_TEXT_BASE to CONFIG_TEXT_BASE The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE and this makes it imposible to use CONFIG_VAL(). Rename it to resolve this problem. Signed-off-by: Simon Glass <sjg@chromium.org>
2022-10-21 00:22:39 +00:00
CONFIG_TEXT_BASE=0x40200000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-01 12:19:22 +00:00
CONFIG_SYS_MALLOC_LEN=0x2000000
Rename GPIO_SUPPORT to GPIO Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-11 03:14:30 +00:00
CONFIG_SPL_GPIO=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-04-28 20:15:47 +00:00
CONFIG_ENV_SIZE=0x2000
CONFIG_ENV_OFFSET=0xFFFFDE00
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_DM_GPIO=y
imx8mm-mx8menlo/verdin-imx8mm: synchronise device tree with linux Synchronise device tree with linux v5.19-rc5. Please note that this also means that instead of the previous "generic" U-Boot specific carrier board agnostic device tree we are now using the regular one for the Verdin Development (carrier) board (e.g. imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb). Please further note that the PMIC node name got changed from a pmic label to pmic@25 which required adjustment in resp. board SPL file board/toradex/verdin-imx8mm/spl.c. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-07-21 13:41:23 +00:00
CONFIG_DEFAULT_DEVICE_TREE="imx8mm-verdin-wifi-dev"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 17:54:25 +00:00
CONFIG_SPL_TEXT_BASE=0x7E1000
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_TARGET_VERDIN_IMX8MM=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-08-23 19:24:14 +00:00
CONFIG_SYS_PROMPT="Verdin iMX8MM # "
mmc: Rename MMC_SUPPORT to MMC Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> [trini: Fixup some incorrect renames] Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-08 18:20:09 +00:00
CONFIG_SPL_MMC=y
serial: Rename SERIAL_SUPPORT to SERIAL Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-08-08 18:20:12 +00:00
CONFIG_SPL_SERIAL=y
Rename DRIVERS_MISC_SUPPORT to DRIVERS_MISC Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-11 03:14:31 +00:00
CONFIG_SPL_DRIVERS_MISC=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SPL=y
verdin-imx8mm: verdin-imx8mp: update env memory layout (again) Update the distro config env memory layout for the Verdin iMX8M Mini and Verdin iMX8M Plus again: - loadaddr=0x48200000 allows for 128MB area for uncompressing (ie FIT images, kernel_comp_addr_r, kernel_comp_size) - fdt_addr_r = loadaddr + 128MB - allows for 128MB kernel - scriptaddr = fdt_addr_r + 512KB - allows for 512KB fdt - ramdisk_addr_r = scriptaddr + 512KB - allows for 512KB script Memory layout taken from commit fd5c7173ade4 ("imx8m{m,n}_venice: update env memory layout"). Note that for our regular BSP Layers and Reference Images for Yocto Project an updated distro boot script is required (see meta-toradex-bsp-common/recipes-bsp/u-boot/u-boot-distro-boot). Note that this corrects a pre-maturely applied version 2 of the same patch set. Fixes: bbe0089d29e ("verdin-imx8mm: verdin-imx8mp: update env memory layout") Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-09-22 21:28:32 +00:00
CONFIG_SYS_LOAD_ADDR=0x48200000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 14:33:18 +00:00
CONFIG_SYS_MEMTEST_START=0x40000000
CONFIG_SYS_MEMTEST_END=0x80000000
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_LTO=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_DISTRO_DEFAULTS=y
Convert CONFIG_SYS_MONITOR_LEN to Kconfig This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2022-10-29 00:27:07 +00:00
CONFIG_SYS_MONITOR_LEN=524288
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_FIT=y
CONFIG_FIT_EXTERNAL_OFFSET=0x3000
configs: toradex: enable missing fit options Add missing support of FIT-images and enable a verbosity for this feature. Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-13 09:33:29 +00:00
CONFIG_FIT_VERBOSE=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SPL_LOAD_FIT=y
verdin-imx8mm: switch to use binman to pack images Use binman to pack images. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Heiko Thiery <heiko.thiery@gmail.com> Reviewed-by: Fabio Estevam <festevam@gmail.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-10-09 20:41:07 +00:00
# CONFIG_USE_SPL_FIT_GENERATOR is not set
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_OF_SYSTEM_SETUP=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_BOOTDELAY=1
verdin-imx8mm: use preboot for fdtfile evaluation Enable and set preboot var with fdtfile evaluation. It will be checked and run immediately before starting the CONFIG_BOOTDELAY countdown and/or running the auto-boot command resp. entering interactive mode. This provides possibility to use different boot cmds in interactive mode without manual setting fdtfile value, as it it's already evaluated before entering interactive mode. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-09 20:41:12 +00:00
CONFIG_USE_PREBOOT=y
configs: tdx: Do not overwrite fdtfile if it got set manually In case a customer wants to set fdtfile currently preboot overrides it always with preboot just before the bootdelay. Use test -n to check if fdtfile is already set and only set it if nothing got touched manually Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-13 09:33:31 +00:00
CONFIG_PREBOOT="test -n ${fdtfile} || setenv fdtfile imx8mm-verdin-${variant}-${fdt_board}.dtb"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 16:22:06 +00:00
CONFIG_LOG=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
ARM: imx8m: Deduplicate CAAM init with arch_misc_init() call Instead of duplicating code implemented by i.MX8M version of arch_misc_init() in every board, enable CONFIG_ARCH_MISC_INIT and call arch_misc_init() from spl_board_init(). This removes the duplication. No functional change. Signed-off-by: Marek Vasut <marex@denx.de> Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-09-19 19:41:15 +00:00
CONFIG_ARCH_MISC_INIT=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 16:22:06 +00:00
CONFIG_BOARD_LATE_INIT=y
Convert CONFIG_SPL_BSS_START_ADDR to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 14:19:45 +00:00
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
CONFIG_SPL_BSS_START_ADDR=0x910000
Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-19 19:09:22 +00:00
CONFIG_SPL_BSS_MAX_SIZE=0x2000
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SPL_BOARD_INIT=y
Convert CONFIG_SPL_STACK to Kconfig This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-26 17:13:21 +00:00
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SPL_STACK=0x920000
Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 16:48:32 +00:00
CONFIG_SYS_SPL_MALLOC=y
CONFIG_HAS_CUSTOM_SPL_MALLOC_START=y
CONFIG_CUSTOM_SYS_SPL_MALLOC_ADDR=0x42200000
CONFIG_SYS_SPL_MALLOC_SIZE=0x80000
Convert CONFIG_CONS_INDEX et al to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-11 19:55:51 +00:00
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300
i2c: Rename SPL/TPL_I2C_SUPPORT to I2C Rename these options so that CONFIG_IS_ENABLED can be used with them. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-11 03:14:36 +00:00
CONFIG_SPL_I2C=y
Rename SPL_POWER_SUPPORT to SPL_POWER Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2021-07-11 03:14:24 +00:00
CONFIG_SPL_POWER=y
Rename SPL_WATCHDOG_SUPPORT to SPL_WATCHDOG Rename this option so that CONFIG_IS_ENABLED can be used with it. Signed-off-by: Simon Glass <sjg@chromium.org>
2021-07-11 03:14:28 +00:00
CONFIG_SPL_WATCHDOG=y
Convert CONFIG_SYS_MAXARGS to Kconfig This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 20:21:06 +00:00
CONFIG_SYS_MAXARGS=64
Convert CONFIG_SYS_CBSIZE to Kconfig This converts the following to Kconfig: CONFIG_SYS_CBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 22:01:06 +00:00
CONFIG_SYS_CBSIZE=2048
Convert CONFIG_SYS_PBSIZE to Kconfig This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 21:38:09 +00:00
CONFIG_SYS_PBSIZE=2081
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
# CONFIG_BOOTM_NETBSD is not set
CONFIG_CMD_ASKENV=y
# CONFIG_CMD_EXPORTENV is not set
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_CRC32_VERIFY=y
CONFIG_CMD_MD5SUM=y
CONFIG_MD5SUM_VERIFY=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_CLK=y
CONFIG_CMD_FUSE=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_CMD_READ=y
ARM: imx8m: verdin-imx8mm: Enable USB Host support Enable USB host support on MX8MM Verdin. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-03-31 21:46:35 +00:00
CONFIG_CMD_USB=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_CMD_BOOTCOUNT=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_CMD_CACHE=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_CMD_TIME=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_CMD_UUID=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_CMD_PMIC=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT4_WRITE=y
# CONFIG_ISO_PARTITION is not set
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
# CONFIG_SPL_EFI_PARTITION is not set
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
Convert CONFIG_ENV_OVERWRITE to Kconfig This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-03 11:48:56 +00:00
CONFIG_ENV_OVERWRITE=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_ENV_IS_IN_MMC=y
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
Convert CONFIG_SYS_MMC_ENV_DEV et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_MMC_ENV_DEV CONFIG_SYS_MMC_ENV_PART Note that with this conversion we now have consistent behavior with respect to ensuring that we have always selected the correct MMC device and hardware partition. Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-24 21:14:47 +00:00
CONFIG_SYS_MMC_ENV_PART=1
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
Convert CONFIG_ETHPRIME to Kconfig This converts the following to Kconfig: CONFIG_ETHPRIME This is also done by adding a gating Kconfig option, CONFIG_USE_ETHPRIME similar to other options that are not always set and control environment variables. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-11 14:12:07 +00:00
CONFIG_USE_ETHPRIME=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_ETHPRIME="eth0"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-10-09 16:22:06 +00:00
CONFIG_VERSION_VARIABLE=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_IP_DEFRAG=y
CONFIG_TFTP_BLOCKSIZE=4096
CONFIG_SPL_DM=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_BOOTCOUNT_LIMIT=y
verdin-imx8mm: various config additions and improvements - enable bootcount command - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-09-22 21:28:33 +00:00
CONFIG_BOOTCOUNT_ENV=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SPL_CLK_COMPOSITE_CCF=y
CONFIG_CLK_COMPOSITE_CCF=y
CONFIG_SPL_CLK_IMX8MM=y
CONFIG_CLK_IMX8MM=y
verdin-imx8mm: enable sleep_moci output This powers some peripherals on the carrier board e.g. the USB hub. Related-to: ELB-3206 Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Fabio Estevam <festevam@gmail.com>
2021-10-09 20:41:08 +00:00
CONFIG_GPIO_HOG=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_MXC_GPIO=y
CONFIG_DM_I2C=y
CONFIG_MISC=y
verdin-imx8mm: add EEPROM support for carrier board Enable these Kconfig symbols: TDX_CFG_BLOCK_EXTRA=y TDX_HAVE_EEPROM_EXTRA=y Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-07-15 10:30:59 +00:00
CONFIG_I2C_EEPROM=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SUPPORT_EMMC_BOOT=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_MMC_IO_VOLTAGE=y
CONFIG_SPL_MMC_IO_VOLTAGE=y
CONFIG_MMC_UHS_SUPPORT=y
CONFIG_SPL_MMC_UHS_SUPPORT=y
CONFIG_MMC_HS400_ES_SUPPORT=y
CONFIG_MMC_HS400_SUPPORT=y
CONFIG_SPL_MMC_HS400_SUPPORT=y
Convert CONFIG_FSL_USDHC to Kconfig This converts the following to Kconfig: CONFIG_FSL_USDHC Signed-off-by: Tom Rini <trini@konsulko.com>
2021-11-08 03:59:37 +00:00
CONFIG_FSL_USDHC=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_PHY_FIXED=y
CONFIG_DM_MDIO=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_SPL_PINCTRL=y
CONFIG_PINCTRL_IMX8M=y
ARM: imx8m: verdin-imx8mm: Enable USB Host support Enable USB host support on MX8MM Verdin. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-03-31 21:46:35 +00:00
CONFIG_POWER_DOMAIN=y
CONFIG_IMX8M_POWER_DOMAIN=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_DM_PMIC=y
verdin-imx8mm: spl: switch to pca9450 pmic V1.1A HW switched the PMIC from BD71837 to PCA9450. - Disable combined DVS in PCA9450_BUCK123_DVS. - Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM. - Configure WDOG_B behaviour. Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-10-28 09:58:12 +00:00
CONFIG_SPL_DM_PMIC_PCA9450=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
configs: verdin-imx8mm: verdin-imx8mp: enable dm serial Enable driver model for serial. Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-08 08:06:57 +00:00
CONFIG_DM_SERIAL=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_MXC_UART=y
CONFIG_SYSRESET=y
ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin Board files should not re-implement do_reset() to work around this function not being defined in for specific configurations. Rather, the fix is to compile in drivers which implement this properly. This patch enables sysreset and watchdog drivers in SPL and ties them together to implement the same as the do_reset() hack in the board file, except correctly in the DM/DT framework. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-04-29 13:04:27 +00:00
CONFIG_SPL_SYSRESET=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_SYSRESET_PSCI=y
ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin Board files should not re-implement do_reset() to work around this function not being defined in for specific configurations. Rather, the fix is to compile in drivers which implement this properly. This patch enables sysreset and watchdog drivers in SPL and ties them together to implement the same as the do_reset() hack in the board file, except correctly in the DM/DT framework. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-04-29 13:04:27 +00:00
CONFIG_SYSRESET_WATCHDOG=y
board: toradex: Add Verdin iMX8M Mini support This adds initial minimal support for the Toradex Verdin iMX8M Mini Quad 2GB WB IT V1.0A module. They are now strapped to boot from eFuses which are factory fused to properly boot from their on-module eMMC. U-Boot supports booting from the on-module eMMC only, SDP support is disabled for now due to missing i.MX 8M Mini USB support. Functionality wise the following is known to be working: - eMMC, 8-bit and 4-bit MMC/SD card slots - Ethernet - GPIOs - I2C Boot sequence is: SPL ---> ATF (TF-A) ---> U-boot proper ATF, U-boot proper and u-boot.dtb images are packed into a FIT image, loaded by SPL. Boot: U-Boot SPL 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) Normal Boot Trying to boot from MMC1 NOTICE: Configuring TZASC380 NOTICE: RDC off NOTICE: BL31: v2.0(release):rel_imx_4.14.98_2.3.0-0-g09c5cc994-dirty NOTICE: BL31: Built : 01:11:41, Jan 25 2020 NOTICE: sip svc init U-Boot 2020.01-00187-gd411d164e5 (Jan 26 2020 - 04:47:26 +0100) CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz Reset cause: POR DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2 Loading Environment from MMC... OK In: serial Out: serial Err: serial Model: Toradex Verdin iMX8M Mini Quad 2GB Wi-Fi / BT IT V1.0A, Serial# 06535149 Net: eth0: ethernet@30be0000 Hit any key to stop autoboot: 0 Verdin iMX8MM # Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com> Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-28 13:42:25 +00:00
CONFIG_DM_THERMAL=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_IMX_TMU=y
ARM: imx8m: verdin-imx8mm: Enable USB Host support Enable USB host support on MX8MM Verdin. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Max Krummenacher <max.krummenacher@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2021-03-31 21:46:35 +00:00
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_USB_KEYBOARD=y
CONFIG_USB_HOST_ETHER=y
ARM: imx8m: Fix reset in SPL on Toradex iMX8MM Verdin Board files should not re-implement do_reset() to work around this function not being defined in for specific configurations. Rather, the fix is to compile in drivers which implement this properly. This patch enables sysreset and watchdog drivers in SPL and ties them together to implement the same as the do_reset() hack in the board file, except correctly in the DM/DT framework. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Fabio Estevam <festevam@gmail.com> Cc: Flavio Suligoi <f.suligoi@asem.it> Cc: Harald Seiler <hws@denx.de> Cc: Igor Opaniuk <igor.opaniuk@toradex.com> Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com> Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Cc: Peng Fan <peng.fan@nxp.com> Cc: Stefano Babic <sbabic@denx.de> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com> Acked-by: Igor Opaniuk <igor.opaniuk@toradex.com>
2020-04-29 13:04:27 +00:00
CONFIG_IMX_WATCHDOG=y
verdin-imx8mm: various config additions and improvements - integrate bootcount using SNVS_LP general purpose register LPGPR0 - enable link-time optimisation - explicitly set a boot delay of one second - enable CRC32 and MD5 - enable command for low-level access to data in a partition - enable time commands - enable PMIC commands - improve ETHPRIME configuration - enable eMMC HS400 functionality - enable fixed PHY and MDIO driver model - remove stale PFUZE100 PMIC driver - enable thermal management unit driver - enable more USB host functionality - enable hexdump Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-08-22 13:06:03 +00:00
CONFIG_HEXDUMP=y
verdin-imx8mm: enable fdt overlays and env importing Enable CONFIG_CMD_IMPORTENV and CONFIG_OF_LIBFDT_OVERLAY needed for booting regular Toradex BSP images. Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com> Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-10-30 14:55:02 +00:00
CONFIG_OF_LIBFDT_OVERLAY=y
Reference in New Issue Copy Permalink