Add the usb3 phyter for the USB3.0 OTG controller.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
After commit '06c47e6286d usb: dwc3: of-simple: Add support to get resets
for the device' you can add the reset property to the dwc3 node, the reset
is required for the controller to work properly, otherwise bind / unbind
stress testing of the USB controller on rk3399 we'd often end up with lots
of failures that looked like this:
phy phy-ff800000.phy.9: phy poweron failed --> -110
dwc3 fe900000.dwc3: failed to initialize core
dwc3: probe of fe900000.dwc3 failed with error -110
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The aclk_usb3 must be enabled to support USB3 for rk3399.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the usb3 power-domain, its qos area and assign it to the usb device
node.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add PWM DT info for the Amlogic's Meson-Axg SoC.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Add new pinctrl DT info for the Amlogic's Meson-AXG SoC.
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
[khilman: dropped unnecessary include]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Try to add Hiubus DT info, and also enable clock DT info
for the Amlogic's Meson-AXG SoC.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Use the sor1_out clock instead of sor1_src. This is a more accurate
model of the hardware and allows for more complicated configurations
such as HDMI 2.0.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the CPU and PSCI nodes for the NVIDIA Tegra210 platforms so that
all CPUs can be enabled on boot. This assumes that the PSCI firmware
has been loaded during the initial bootstrap on the device before the
kernel starts (which is typically the case for these platforms). The
PSCI firmware version is set to v0.2 which aligns with the current
shipping version for Tegra.
Reported-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Enable the host1x and necessary children and hook up the HDMI +5V pin to
enable video output on the HDMI port found on Jetson TX2.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Adds the device tree nodes for the display hub and display controllers
as well as the DPAUX, DSI and SOR controllers.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add the DT node for ARM SMMU on Tegra186.
Signed-off-by: Krishna Reddy <vdumpa@nvidia.com>
Reviewed-by: Mikko Perttunen <mperttunen@nvidia.com>
Tested-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The FUSE register block found on Tegra186 SoCs encodes various settings,
such as calibration data for other blocks.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The MISC register block found on Tegra186 SoCs contains registers that
can be used to identify a given chip and various strapping options.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort root sub-nodes alphabetically for allow for easier maintenance
of this file.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Commit 15e85695e5 ("arm64: dts: uniphier: add GPIO hog definition")
missed to update the PXs3 DTS for some reason. Do it now.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The dt-bindings header was applied to the driver subsystem. I had to
wait for a merge window to use it from DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
On ULCB, the enable pin of the regulator providing PHY power is always
pulled high, but the driver may still need to reset the PHY if this
wasn't done by the bootloader before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the GPIO used to reset the Ethernet PHY for EthernetAVB.
This allows the driver to reset the PHY during probe and after system
resume.
This fixes Ethernet operation after resume from s2ram on Salvator-XS,
where the enable pin of the regulator providing PHY power is connected
to PRESETn, and PSCI powers down the SoC during system suspend.
On Salvator-X, the enable pin is always pulled high, but the driver may
still need to reset the PHY if this wasn't done by the bootloader
before.
Inspired by patches in the BSP for the individual Salvator-X/XS boards
by Kazuya Mizuguchi.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
-----BEGIN PGP SIGNATURE-----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=xHta
-----END PGP SIGNATURE-----
Merge tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes
Amlogic fixes for v4.15-rc
- GPIO interrupt fixes
- socinfo fix for GX series
- fix typo
* tag 'amlogic-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: fix UART pclk clock name
meson-gx-socinfo: Fix package id parsing
ARM: meson: fix spelling mistake: "Couln't" -> "Couldn't"
ARM: dts: meson: fix the memory region of the GPIO interrupt controller
ARM: dts: meson: correct the sort order for the the gpio_intc node
Signed-off-by: Olof Johansson <olof@lixom.net>
Correct the interrupt number assigned to the Realtek PHY in the q200
Fixes: b94d22d94a ("ARM64: dts: meson-gx: add external PHY interrupt on some platforms")
Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The INTB/PMEB pin of the RTL8211F PHY on the Khadas VIM2 is routed to
GPIOZ_15. Add the corresponding interrupt using the GPIO interrupt
controller so the PHY framework doesn't have to poll the PHY for it's
status.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Currently one has to look/calculate the GPIO for the PHY interrupts
manually. Add a comment for the existing PHY interrupt lines to make it
easier to find out which GPIO is used.
This is done using the following calculation:
- number of GPIO AO pins (14 on GXBB: GPIOAO_0..13)
- add the offset of the pin which is used for the interrupt (for example
GPIOZ_15 = 15 on Odroid-C2)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-By: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The DT spec recommends that node-names have generic names like "bus".
Fix that in the Amlogic DTs, while leaving the label names to have more
SoC-specific names that match with the HW documentation.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The clock-names for pclk was wrongly set to "core", but the bindings
specifies "pclk".
This was not cathed until the legacy non-documented bindings were removed.
Reported-by: Andreas Färber <afaerber@suse.de>
Fixes: f72d6f6037 ("ARM64: dts: meson-gx: use stable UART bindings with correct gate clock")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
The Bananapi-M64 has 3 LEDS in red, green, and blue. These are toggled
via GPIO lines, which drive transistors that control current across the
LEDS. The red LED is by default on, via an additional pull-up on the
control line. We consider this means that it is a power indicator.
So we set the "default-on" property for it.
The pingroups the GPIO lines belong to require external regulators be
enabled to be able to drive the GPIO high. These regulators also have
other purposes. However the pin controller does not have bindings for
regulators. Here we just set them to always-on.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The SAR ADC modules doesn't require The "sana" clock.
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Singed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now the VPU Power Domain has been fixed while boothing from Mainline U-Boot,
VPU and HDMI nodes can finally be added to the Odroid-C2 DTS.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Now the Amlogic Meson GX SoCs datasheet documents all the Reset registers,
grow the memory in the node to allow usage of the level registers.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
On reference boards and derivatives, the HDMI Logic is powered by an external
5V regulator.
This regulator was set by the Vendor U-Boot, add the regulator and set it always-on for now.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
This patch adds support for the VPU Power Domain nodes, and attaches the
VPU power domain to the VPU node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
It looks like either the current kernel or the hardware has reliability
issues when the gmac is actually running at 1GBit. In my test-case
it is not able to boot on a nfsroot at this speed, as the system
will always lose the connection to the nfs-server during boot, before
reaching any login prompt and not recover from this.
So until this is solved, limit the speed to 100MBit as with this the
nfsroot survives stress tests like an apt-get upgrade without problems.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
vdd_log has no consumer and therefore will not be set to a specific
voltage. Still the PWM output pin gets configured and thence the vdd_log
output voltage will changed from it's default. Depending on the idle
state of the PWM this will slightly over or undervoltage the logic supply
of the RK3399 and cause instability with GbE (undervoltage) and PCIe
(overvoltage). Since the default value set by a voltage divider is the
correct supply voltage and we don't need to change it during runtime we
remove the rail from the devicetree completely so the PWM pin will not
be configured.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The sdcard detect pin on orange-pi-zero-plus2 is pulled up.
Fix cd-gpio description to enable sdcard detect.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since current tree support AXP803 regulators,
replace fixed regulator vcc3v3 with AXP803 dcdc1 regulator where ever
it need to replace.
Tested mmc0 on sopine baseboard.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the commit 833bdb47c8 ("dt-bindings: power: add R8A77970 SYSC
power domain definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the commit ecadea00f5 ("dt-bindings: clock: Add R8A77970 CPG
core clock definitions") has hit Linus' tree, we can replace the bare
numbers (we had to use to avoid a cross tree dependency) with these macro
definitions...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add edp panel and enable related nodes on kevin.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Mark Yao <mark.yao@rock-chips.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Probably due to some copy-paste mistake, the tsadc of rk3328 ended up
with a 0 as 4th element that shouldn't be there, as interrupts on the
rk3328 only have multiples of 3, making dtc complain. So remove it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
sii8620 supports 1 MHz clock, it allows faster transmissions and according
to extensive tests allows to mitigate some obscure bugs in I2C client
logic of the chip.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We might include additional ports in derivative device trees, so the
'port' node should have an address, and the parent 'ports' node needs
/#{addres,size}-cells.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds the information for the secondary MIPI DSI controller,
e.g., interrupts, grf, clocks, ports and so on. Mirrors the existing
definition for dsi0.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We've documented this one already, but we didn't add it to the DTSI yet.
Suggested-by: Nickey Yang <nickey.yang@rock-chips.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Define the V3M Starter Kit board dependent part of the EtherAVB
device node.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the V3M Starter Kit board.
The board has 1 debug serial port (SCIF0); include support for it,
so that the serial console can work.
Based on the original (and large) patch by Vladimir Barinov.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The list is almost sorted. Move "lg" up to complete it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch adds support for G2D, G3D, CAM0, CAM1, ISP, HVEC power domains
to Exynos5433 SoCs. Currently only clock controllers for those domains are
defined. CAM1 is a parent of CAM0 power domain and CAM0 is a parent of ISP
power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for AUD power domain to Exynos5433 SoCs, which
contains following devices: a clock controller, a pin controller, LPASS
module, I2S controller, ADMA PL330 engine and UART #3 device.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for MFC power domain to Exynos 5433 SoCs, which
contains following devices: a clock controller, MFC codec device and its
SYSMMUs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for MSCL power domain to Exynos 5433 SoCs, which
contains following devices: a clock controller, JPEG codec device and its
SYSMMU.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for DISP power domain to Exynos 5433 SoCs, which
contains following devices: a clock controller, two display controllers
(DECON and DECON TV), their SYSMMUs, MIC, DSI and HDMI video devices.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch adds support for GSCL power domain to Exynos 5433 SoCs, which
contains following devices: a clock controller, three GSCL video scalers and
their SYSMMUs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Add device tree node with S3FWRN5 NFC chip to TM2(e) boards. The chip is
connected through HS-I2C bus #4.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
[mszyprow: rebased onto v4.15-rc1, moved node to exynos5433-tm2-common.dtsi,
rephrased commit message]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable support for ARM Performance Monitoring Units available in
Cortex-A53 and Cortex-A57 CPU cores for Exynos5433 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
add arm64 H5 dwmac-sun8i support for this board
Signed-off-by: Antony Antony <antony@phenome.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These were added to make the ARM64 branch self-contained because
updates for ARM and ARM64 are supposed to be sent as separate
pull requests.
Now, they were merged together in Linus' tree and interrupt-parent
from the arch/arm/boot/dts/uniphier-support-card.dtsi is visible from
ARM64 DT files by the cross-arch reference.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77995 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7795 and r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a77970 device nodes for IPMMU-DS1, IPMMU-RT
and the shared IPMMU-MM device.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-RT to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a77970 DMAC nodes to the IPMMU. In particular
SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Based on work for the r8a7796 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a77970 IPMMU nodes and keep all disabled by default.
Based on work for the r8a7796 by Magnus Damm
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Sort includes used in r8a77970 DTS to improve maintainability
and for consistency with other R-Car DTS files.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch changes the number of GPIO bank 1 ports to 29 because GP-1-28
port pin of R8A7795 ES2.0 SoC support was added.
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Fixes: 291e0c4994 ("arm64: dts: r8a7795: Add support for R-Car H3 ES2.0")
[geert: Keep 28 GPIOs on H3 ES1.x after r8a7795.dtsi sharing]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN FD controller node for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds CAN controller nodes for r8a77995.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds external CAN clock node for r8a77995. This clock can be used as
fCAN clock of CAN and CAN FD controller.
Based on a patch for r8a7796 by Chris Paterson.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-XS boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Document clearly which SoC this DTS applies to, to distinguish from
Salvator-X boards equipped with other SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the ROHM BD9571MWV PMIC.
This was based on the example in the DT binding documentation, but using
IRQ0 instead of a GPIO interrupt, as that matches the schematics, and
because INTC-EX is a simpler block.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-VI0, IPMMU-VP1, IPMMU-DS0,
IPMMU-DS1 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the r8a7795 ES1.x device node for IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-HC to the SATA device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVB devices to allow use of VSPBC/VSPBD with
IPMMU-VP0 and IPMMU-VP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VP.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVD devices to allow use of the VSP and DU
together with IPMMU-VI1 and IPMMU-VI1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 ES2.0 Audio-DMAC nodes to the IPMMU-MP0.
Hook up r8a7795 ES1.x Audio-DMAC nodes to the IPMMU-MP1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7795 SYS-DMAC nodes to the IPMMUs. In particular SYS-DMAC0 gets
tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 ES1.x IPMMU nodes and keep all disabled by default.
This is a follow-up to a patch that adds IPMMU device nodes that
are common to r8a7795 ES1.x and ES2.0
Power domains are omitted as they appear to be undocumented.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7795 IPMMU nodes and keep all disabled by default.
This includes all IPMMU devices for r8a7795 ES2.0. Those
not present in r8a7795 ES1.x are removed from the DT for those
SoCs using delete-node. A follow-up patch will add IPMMU devices
to ES1.x which are not also present in ES2.0.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
R-Car D3 has only one SDHI controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Differs from other Gen3 SoCs in that each controller only supports eight
channels.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
ULCB-KF has a USB2.0 dual-role channel (CN13).
This adds dr_mode property for USB2.0 channel 0 (EHCI/OHCI and HS-USB)
as "otg".
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This supports USB2 PHY channel #0 on ULCB Kingfisher board
The dedicated USB0_PWEN pin is used to control CN13 VBUS source from U43
power supply.
MAX3355 can also provide VBUS, hence it should be disabled via OTG_OFFVBUSn
node coming from gpio expander TCA9539.
Set MAX3355 enabled using OTG_EXTLPn node to be able to read OTG ID of
CN13.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the r8a7795 device nodes for IPMMU-DS0, IPMMU-DS1, IPMMU-MP,
IPMMU-VI0, IPMMU-VC0 and the shared IPMMU-MM device.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add IPMMU-DS0 to the Ethernet-AVB device node.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPVI devices to allow use of VSPI with IPMMU-VC0.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up the FCPF devices to allow use of FDP1 with IPMMU-VI0.
Based on work by Magnus Damm for the r8a7795.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 Audio-DMAC nodes to the IPMMU-MP.
Based on work for the r8a7795 by Magnus Damm.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Hook up r8a7796 DMAC nodes to the IPMMUs. In particular SYS-DMAC0
gets tied to IPMMU-DS0, and SYS-DMAC1 and SYS-DMAC2 get tied to IPMMU-DS1.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add r8a7796 IPMMU nodes and keep all disabled by default.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add initial support for the Renesas Salvator-XS (Salvator-X 2nd version)
development board equipped with an R-Car M3-W SiP.
Based on work for the Salvator-X and -XS boards with M3-W resp. H3 SiPs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Enable the Watchdog Timer (WDT) controller on the Renesas Eagle
board equipped with an R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the Watchdog Timer (WDT) controller on the
Renesas R-Car V3M (r8a77970) SoC.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car SDHI Gen3 fallback compat string
in the DT of the r8a7796 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use newly added R-Car SDHI Gen3 fallback compat string
in the DT of the r8a7795 SoC.
This should have no run-time effect as the driver matches against
the per-SoC compat string before considering the fallback compat string.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
These boards are known to have eMMC issues with the default driver type.
Specify a working one.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
PF6 is mostly used as the CD pin for the microSD slot on H5 based
boards. So far we were referencing this pin twice: once using the
mmc0_cd_pin phandle, and then again directly as a GPIO via the pinctrl
phandle.
This will cause problems if the pinctrl driver enables strict mode, as
the second request will fail now, leading to a driver init failure.
Remove the redundant pin reference via the mmc0_cd_pin phandle.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reported-by: Chris Obbard <obbardc@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On several A64 boards the Ethernet PHY is powered by the DC1SW regulator
on the AXP803 PMIC.
Add phy-handle property to these boards' emac node.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Tested-by: Corentin LABBE <clabbe.montjoie@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable AXP803 PMIC and regulators for Orangepi Win.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
We add device tree files for a couple of additional SoCs in various areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for networking,
Amlogic A113D for audio, and Renesas R-Car V3M for automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX, Amlogic
and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues that
the latest version of 'dtc' now warns about. Unfortunately there is still
a lot left to do.
A rework of the ARM foundation model introduced several new files
for common variations of the model.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TnSo
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM device-tree updates from Arnd Bergmann:
"We add device tree files for a couple of additional SoCs in various
areas:
Allwinner R40/V40 for entertainment, Broadcom Hurricane 2 for
networking, Amlogic A113D for audio, and Renesas R-Car V3M for
automotive.
As usual, lots of new boards get added based on those and other SoCs:
- Actions S500 based CubieBoard6 single-board computer
- Amlogic Meson-AXG A113D based development board
- Amlogic S912 based Khadas VIM2 single-board computer
- Amlogic S912 based Tronsmart Vega S96 set-top-box
- Allwinner H5 based NanoPi NEO Plus2 single-board computer
- Allwinner R40 based Banana Pi M2 Ultra and Berry single-board computers
- Allwinner A83T based TBS A711 Tablet
- Broadcom Hurricane 2 based Ubiquiti UniFi Switch 8
- Broadcom bcm47xx based Luxul XAP-1440/XAP-810/ABR-4500/XBR-4500
wireless access points and routers
- NXP i.MX51 based Zodiac Inflight Innovations RDU1 board
- NXP i.MX53 based GE Healthcare PPD biometric monitor
- NXP i.MX6 based Pistachio single-board computer
- NXP i.MX6 based Vining-2000 automotive diagnostic interface
- NXP i.MX6 based Ka-Ro TX6 Computer-on-Module in additional variants
- Qualcomm MSM8974 (Snapdragon 800) based Fairphone 2 phone
- Qualcomm MSM8974pro (Snapdragon 801) based Sony Xperia Z2 Tablet
- Realtek RTD1295 based set-top-boxes MeLE V9 and PROBOX2 AVA
- Renesas R-Car V3M (R8A77970) SoC and "Eagle" reference board
- Renesas H3ULCB and M3ULCB "Kingfisher" extension infotainment boards
- Renasas r8a7745 based iWave G22D-SODIMM SoM
- Rockchip rk3288 based Amarula Vyasa single-board computer
- Samsung Exynos5800 based Odroid HC1 single-board computer
For existing SoC support, there was a lot of ongoing work, as usual
most of that concentrated on the Renesas, Rockchip, OMAP, i.MX,
Amlogic and Allwinner platforms, but others were also active.
Rob Herring and many others worked on reducing the number of issues
that the latest version of 'dtc' now warns about. Unfortunately there
is still a lot left to do.
A rework of the ARM foundation model introduced several new files for
common variations of the model"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (599 commits)
arm64: dts: uniphier: route on-board device IRQ to GPIO controller for PXs3
dt-bindings: bus: Add documentation for the Technologic Systems NBUS
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
ARM: dts: owl-s500: Add CubieBoard6
dt-bindings: arm: actions: Add CubieBoard6
ARM: dts: owl-s500-guitar-bb-rev-b: Add fake uart3 clock
ARM: dts: owl-s500: Set power domains for CPU2 and CPU3
arm: dts: mt7623: remove unused compatible string for pio node
arm: dts: mt7623: update usb related nodes
arm: dts: mt7623: update crypto node
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
...
Commit 429f203eb7 ("arm64: dts: uniphier: route on-board device IRQ
to GPIO controller") missed to update this DTS. It becames a real
problem when arm and arm64 trees are merged together.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing memory
leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node. The
prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to dtb
compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage Technology,
shimafuji, Tecon Microprocessor Technologies, DH electronics GmbH,
Opal Kelly, and Next Thing
-----BEGIN PGP SIGNATURE-----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=jgpN
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
"A bigger diffstat than usual with the kbuild changes and a tree wide
fix in the binding documentation.
Summary:
- kbuild cleanups and improvements for dtbs
- Code clean-up of overlay code and fixing for some long standing
memory leak and race condition in applying overlays
- Improvements to DT memory usage making sysfs/kobjects optional and
skipping unflattening of disabled nodes. This is part of kernel
tinification efforts.
- Final piece of removing storing the full path for every DT node.
The prerequisite conversion of printk's to use device_node format
specifier happened in 4.14.
- Sync with current upstream dtc. This brings additional checks to
dtb compiling.
- Binding doc tree wide removal of leading 0s from examples
- RTC binding documentation adding missing devices and some
consolidation of duplicated bindings
- Vendor prefix documentation for nutsboard, Silicon Storage
Technology, shimafuji, Tecon Microprocessor Technologies, DH
electronics GmbH, Opal Kelly, and Next Thing"
* tag 'devicetree-for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (55 commits)
dt-bindings: usb: add #phy-cells to usb-nop-xceiv
dt-bindings: Remove leading zeros from bindings notation
kbuild: handle dtb-y and CONFIG_OF_ALL_DTBS natively in Makefile.lib
MIPS: dts: remove bogus bcm96358nb4ser.dtb from dtb-y entry
kbuild: clean up *.dtb and *.dtb.S patterns from top-level Makefile
.gitignore: move *.dtb and *.dtb.S patterns to the top-level .gitignore
.gitignore: sort normal pattern rules alphabetically
dt-bindings: add vendor prefix for Next Thing Co.
scripts/dtc: Update to upstream version v1.4.5-6-gc1e55a5513e9
of: dynamic: fix memory leak related to properties of __of_node_dup
of: overlay: make pr_err() string unique
of: overlay: pr_err from return NOTIFY_OK to overlay apply/remove
of: overlay: remove unneeded check for NULL kbasename()
of: overlay: remove a dependency on device node full_name
of: overlay: simplify applying symbols from an overlay
of: overlay: avoid race condition between applying multiple overlays
of: overlay: loosen overly strict phandle clash check
of: overlay: expand check of whether overlay changeset can be removed
of: overlay: detect cases where device tree may become corrupt
of: overlay: minor restructuring
...
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=3Gvx
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Introduce host claiming by context to support blkmq
- Preparations for enabling CQE (eMMC CMDQ) requests
- Re-factorizations to prepare for blkmq support
- Re-factorizations to prepare for CQE support
- Fix signal voltage switch for SD cards without power cycle
- Convert RPMB to a character device
- Export eMMC revision via sysfs
- Support eMMC DT binding for fixed driver type
- Document mmc_regulator_get_supply() API
MMC host:
- omap_hsmmc: Updated regulator management for PBIAS
- sdhci-omap: Add new OMAP SDHCI driver
- meson-mx-sdio: New driver for the Amlogic Meson8 and Meson8b SoCs
- sdhci-pci: Add support for Intel CDF
- sdhci-acpi: Fix voltage switch for some Intel host controllers
- sdhci-msm: Enable delay circuit calibration clocks
- sdhci-msm: Manage power IRQ properly
- mediatek: Add support of mt2701/mt2712
- mediatek: Updates management of clocks and tunings
- mediatek: Upgrade eMMC HS400 support
- rtsx_pci: Update tuning for gen3 PCI-Express
- renesas_sdhi: Support R-Car Gen[123] fallback compatibility strings
- Catch all errors when getting regulators
- Various additional improvements and cleanups"
* tag 'mmc-v4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (91 commits)
sdhci-fujitsu: add support for setting the CMD_DAT_DELAY attribute
dt-bindings: sdhci-fujitsu: document cmd-dat-delay property
mmc: tmio: Replace msleep() of 20ms or less with usleep_range()
mmc: dw_mmc: Convert timers to use timer_setup()
mmc: dw_mmc: Cleanup the DTO timer like the CTO one
mmc: vub300: Use common code in __download_offload_pseudocode()
mmc: tmio: Use common error handling code in tmio_mmc_host_probe()
mmc: Convert timers to use timer_setup()
mmc: sdhci-acpi: Fix voltage switch for some Intel host controllers
mmc: sdhci-acpi: Let devices define their own private data
mmc: mediatek: perfer to use rise edge latching for cmd line
mmc: mediatek: improve eMMC hs400 mode read performance
mmc: mediatek: add latch-ck support
mmc: mediatek: add support of source_cg clock
mmc: mediatek: add stop_clk fix and enhance_rx support
mmc: mediatek: add busy_check support
mmc: mediatek: add async fifo and data tune support
mmc: mediatek: add pad_tune0 support
mmc: mediatek: make hs400_tune_response only for mt8173
arm64: dts: mt8173: remove "mediatek, mt8135-mmc" from mmc nodes
...
If CONFIG_OF_ALL_DTBS is enabled, "make ARCH=arm64 dtbs" compiles each
DTB twice; one from arch/arm64/boot/dts/*/Makefile and the other from
the dtb-$(CONFIG_OF_ALL_DTBS) line in arch/arm64/boot/dts/Makefile.
It could be a race problem when building DTBS in parallel.
Another minor issue is CONFIG_OF_ALL_DTBS covers only *.dts in vendor
sub-directories, so this broke when Broadcom added one more hierarchy
in arch/arm64/boot/dts/broadcom/<soc>/.
One idea to fix the issues in a clean way is to move DTB handling
to Kbuild core scripts. Makefile.dtbinst already recognizes dtb-y
natively, so it should not hurt to do so.
Add $(dtb-y) to extra-y, and $(dtb-) as well if CONFIG_OF_ALL_DTBS is
enabled. All clutter things in Makefiles go away.
As a bonus clean-up, I also removed dts-dirs. Just use subdir-y
directly to traverse sub-directories.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
[robh: corrected BUILTIN_DTB to CONFIG_BUILTIN_DTB]
Signed-off-by: Rob Herring <robh@kernel.org>
We need to add "clean-files" in Makfiles to clean up DT blobs, but we
often miss to do so.
Since there are no source files that end with .dtb or .dtb.S, so we
can clean-up those files from the top-level Makefile.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rob Herring <robh@kernel.org>
Most of DT files are compiled under arch/*/boot/dts/, but we have some
other directories, like drivers/of/unittest-data/. We often miss to
add gitignore patterns per directory. Since there are no source files
that end with .dtb or .dtb.S, we can ignore the patterns globally.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Rob Herring <robh@kernel.org>
and efuses on rk3368.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAlnxjcYQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgQg9CACKoNn8LseipJa0kc6ZYXXtVDurmVHgaPyV
OpC3+YbN9tpaBh6lsujkecthmlS45qrjZUsw00P50vcGbrMgrB9zytVrFrpEVxQT
iNdEccU9RFEZ1GSQTPstxI3Uv1fnDcqSCplzKEeVxZ/U7vwWwq5YAi4bSey6eMzc
GNq6FfT65Uf07a0Ondn3+IUzvjRpY42BHjjQjMv3k3lSn7z94/OG0AmCkRrXkBw/
0+jxf9eMkkEj3JaC+OhwHOLJn7bv2U67HPGjLV7BLfFUQYGjPYd8g+LdeVV9Y2PJ
urGiu3o/VbUbTbl2+TWh+OWYbfLFhpBdE+ouPHBPxJMPFkiGnrdA
=xf8q
-----END PGP SIGNATURE-----
Merge tag 'v4.15-rockchip-dts64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Pull "Rockchip dts64 updates for 4.15 part2" from Heiko Stübner:
Support for the RGA (raster graphics accelerator) on rk3399
and efuses on rk3368.
* tag 'v4.15-rockchip-dts64-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: add efuse for RK3368 SoCs
arm64: dts: rockchip: add RGA device node for RK3399
clk: rockchip: add more rk3188 graphics clock ids
clk: rockchip: add clock id for PCLK_EFUSE256 of RK3368 SoCs
Reintroduction of the EMAC bindings that were reverted in 4.13.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJaACruAAoJEBx+YmzsjxAgkK0QAL1BCHcrpftvznMta5QuuHrE
fP++mGTv/upsnfGCb5D1gsQu+6bqyomrbCUjZspl7s+qrJSZo5Flto5KepPFNG4M
vaFApl27HdUM4ppsOAVCokEp8r/QmRppc1CbDF0wqKL996ShUs71zwJ1yEZ5OwgR
1j5hcmEwUhHC6mpROeycYG9+cp040q8Mj01hA5ClfrlwITTqf2rZWF51MTtraUDK
3glww3ZCx9MdivqvlH8EKAKBaExIctoj9LZAcQZee+5yrKsXlOpzYwSO2qs4KxxA
/5pdXitPp27jzzVB9w0oyYXb2ehixXHT6cYmTb4Ny9p+8xQo4V5qk++nMyY+kV2l
1FJlVCLR+I4eYgr6ekWFWanxnyGwcLNtOCggfvSVYrwjHGsBjyX7tOZM1zfHRWP+
W1DbWODow0So1b91Jfu63hyxkXawp2qA1+rMkrFnTHeXz3NRxdbTHP0SroXaWZd7
e06WGxNVH/7SBtozkfvMk8rt3loXW1Rghx+R7d2HmU9AjZBgnVErf9TUAwD7S/rV
rlfAUeRPN9uO7tjbEXysBKqNgXGBFIHcWEaEgETePvWwadG1sA7+Y+Pt1mXinpV0
7SIE6JRzYgORXh7fii91gTlv0cr4VwfrxO+Ik0yMflfxgZ66FruwY8Q3Qjd2x8na
6yIpvwY9I57usi7RW8nQ
=mDKb
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner arm64 changes, take 2" from Maxime Ripard:
Reintroduction of the EMAC bindings that were reverted in 4.13.
* tag 'sunxi-dt64-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
arm64: dts: allwinner: add snps,dwmac-mdio compatible to emac/mdio
arm64: dts: allwinner: A64: Restore EMAC changes
Add the extended UART support on Armada 3700
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWgHNayMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71bHpAJ0QFOqPb3Et
NHXbvRjusO7ZZ+B6+wCff8at95p9E8X5ULnGpR7qINZHKh8=
=CdWu
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt64-4.15-2' of git://git.infradead.org/linux-mvebu into next/dt
Pull "mvebu dt64 for 4.15 (part 2)" from Gregory CLEMENT:
Add the extended UART support on Armada 3700
* tag 'mvebu-dt64-4.15-2' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: armada-3720-espressobin: fill UART nodes
arm64: dts: marvell: armada-3720-db: enable second UART port
arm64: dts: marvell: armada-37xx: add second UART port
arm64: dts: marvell: armada-37xx: add UART clock
Two long awaited changes:
- Reintroduction of the new EMAC DT bindings that got reverted at the
last minute in 4.13
- Introduction of the AXP803/813 PMIC support
-----BEGIN PGP SIGNATURE-----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=96rw
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt
Pull "Allwinner DT changes for 4.15, take 2" from Maxime Ripard:
Here are a few commits that would be great to get in 4.15, given how
long they've been hanging around.
The first and most important one is the reintroduction of the EMAC DT
changes after they've been reverted at the last minute in 4.13.
There's a arm64 patch that crept in because the H5 and H3 share a
common DTSI that is located in arch/arm, and merging that patch
through the arm64 PR, especially given the pull requests that have
already been sent, would just have generated too many conflicts.
* tag 'sunxi-dt-for-4.15-2' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Enable USB OTG
ARM: dts: sun8i: a711: Add regulator support
ARM: dts: sun8i: a83t: bananapi-m3: Enable AP6212 WiFi on mmc1
ARM: dts: sun8i: a83t: cubietruck-plus: Enable AP6330 WiFi on mmc1
ARM: dts: sun8i: a83t: Move mmc1 pinctrl setting to dtsi file
ARM: dts: sun8i: a83t: allwinner-h8homlet-v2: Add AXP818 regulator nodes
ARM: dts: sun8i: a83t: bananapi-m3: Add AXP813 regulator nodes
ARM: dts: sun8i: a83t: cubietruck-plus: Add AXP818 regulator nodes
ARM: dts: sunxi: Add dtsi for AXP81x PMIC
arm64: dts: allwinner: H5: Restore EMAC changes
ARM: dts: sunxi: Restore EMAC changes (boards)
ARM: dts: sunxi: h3/h5: represent the mdio switch used by sun8i-h3-emac
arm: dts: sunxi: h3/h5: Restore EMAC changes
dt-bindings: net: dwmac-sun8i: update documentation about integrated PHY
dt-bindings: net: Restore sun8i dwmac binding
This refactors the RTD1295 DT, preparing for (but not yet adding)
RTD1293 and RTD1296. Superfluous reg property entries are dropped.
DTs for PROBOX2 AVA and MeLE V9 TV boxes are added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=8sRS
-----END PGP SIGNATURE-----
Merge tag 'realtek-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek into next/dt
Pull "Realtek ARM64 based SoC DT for v4.15" from Andreas Färber:
This refactors the RTD1295 DT, preparing for (but not yet adding)
RTD1293 and RTD1296. Superfluous reg property entries are dropped.
DTs for PROBOX2 AVA and MeLE V9 TV boxes are added.
* tag 'realtek-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek:
arm64: dts: realtek: Add MeLE V9
dt-bindings: arm: realtek: Document MeLE V9
dt-bindings: Add vendor prefix for MeLE
arm64: dts: realtek: Factor out common RTD129x parts
arm64: dts: realtek: Add ProBox2 Ava
dt-bindings: arm: realtek: Add ProBox2 AVA
dt-bindings: Add vendor prefix for ProBox2
arm64: dts: realtek: Clean up RTD1295 UART reg property
This updates the Bubblegum-96 DT with a clock node for the debug UART.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=5o4s
-----END PGP SIGNATURE-----
Merge tag 'actions-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions into next/dt
Pull "Actions Semi ARM64 based SoC DT for v4.15" from Andreas Färber:
This updates the Bubblegum-96 DT with a clock node for the debug UART.
* tag 'actions-arm64-dt-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-actions:
arm64: dts: actions: s900-bubblegum-96: Add fake uart5 clock
Only two patches came in over the last two weeks: Uniphier USB support
needs additional clocks enabled (on both 32-bit and 64-bit ARM), and
a Marvell MVEBU stability issue has been fixed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=pn9T
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"Only two patches came in over the last two weeks: Uniphier USB support
needs additional clocks enabled (on both 32-bit and 64-bit ARM), and a
Marvell MVEBU stability issue has been fixed"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: mvebu: pl310-cache disable double-linefill
arm64: dts: uniphier: add STDMAC clock to EHCI nodes
ARM: dts: uniphier: add STDMAC clock to EHCI nodes
devicetree bindings has been updated to support multi-platforms,
so that each platform has its owns compatible name.
And, this compatible name may used in driver to distinguish with
other platform.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Tested-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for H5
This reverts a part of commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
stmmac bindings docs said that its mdio node must have
compatible = "snps,dwmac-mdio";
Since dwmac-sun8i does not have any good reasons to not doing it, all
their MDIO node must have it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The original dwmac-sun8i DT bindings have some issue on how to handle
integrated PHY and was reverted in last RC of 4.13.
But now we have a solution so we need to get back that was reverted.
This patch restore arm64 DT about dwmac-sun8i for A64
This reverts commit 87e1f5e8bb ("arm64: dts: allwinner: Revert EMAC changes")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fill ESPRESSObin uart0 node with pinctrl information like in the
Armada-3720-DB device tree (which uses the same node).
Also explain how to enable the second UART port available on the
headers. This second port is not enabled by default because both
headers are dedicated to expose general purpose pins and remapping
some of them to use the second UART would break existing users.
Suggested-by: László ÁSHIN <laszlo@ashin.hu>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable Armada-3720-DB second UART port by adding the corresponding
device tree node in the board DTS and enabling it.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a node in Armada 37xx DTSI file for the second UART, with a
different compatible due to its extended IP which has some
differences with the first UART already in place.
Make use of this commit to also fully describe the first port and
use the same clear and named interrupt bindings for both ports.
The standard UART (UART0) uses level-interrupts while the extended
UART (UART1) uses edge-triggered interrupts.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add the missing clock property to armada-3700 UART node.
This clock will be used to derive the prescaler value to comply with
the requested baudrate.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- add support for new GPIO IRQ driver
-----BEGIN PGP SIGNATURE-----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=vVV3
-----END PGP SIGNATURE-----
Merge tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into next/dt
Pull "Amlogic 64-bit DT updates for v4.15, round 2" from Kevin Hilman:
- add support for new GPIO IRQ driver
* tag 'amlogic-dt64-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
ARM64: dts: meson-gx: add external PHY interrupt on some platforms
ARM64: dts: meson-gx: add gpio interrupt controller
ARM64: meson: enable MESON_IRQ_GPIO in Kconfig
ARM64: dts: meson-gxbb-odroidc2: fix usb1 power supply
- Add GICv3 ITS node and PCIe devcies for LS1088A support.
- Enable PCIe support for LS2088A SoC.
- Add OP-TEE support for various Layerscape SoCs, LS1012A, LS1043A,
LS1046A, LS1088A and LS208XA.
- Update DPAA QBMan nodes to use constant defines in the interrupt
description.
- Add DSPI device to support SPI-NOR on LS1012A based boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZ7y0kAAoJEFBXWFqHsHzOE70H/iAI1WmTWW1kuc2d7w1pCZrP
m3aBdavPb6N2XT43HUDo5yuAVl84AvmoHWkOXeiAEgSTwuGCMcAT90P3v+MJQG5P
xFCuqEAYfKb4BwMNs3oBbgdWBErxOpqFGd58vvXbEHzGv6DCnJRD6euhVNMosTKv
QI62vZkbD3sR1aUcC/dLG0hCFRb7+fscL+sgtU0vnF5nWKQLXQ/eGCDhhh4mmY/5
sjgeCqhYeIBrhpoOLm8qK9CkRnf7nPZwSiTFhG1o0nHDqbmzTRU5zQrAEDGB9Ukg
pWDtHyIEkrmnzOucIbKVpFue7IldkR7WN2rslpkHhtDaK1gIYnhjO26toU7/f2U=
=T0d9
-----END PGP SIGNATURE-----
Merge tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Pull "Freescale arm64 device tree updates for 4.15" from Shawn Guo:
- Add GICv3 ITS node and PCIe devcies for LS1088A support.
- Enable PCIe support for LS2088A SoC.
- Add OP-TEE support for various Layerscape SoCs, LS1012A, LS1043A,
LS1046A, LS1088A and LS208XA.
- Update DPAA QBMan nodes to use constant defines in the interrupt
description.
- Add DSPI device to support SPI-NOR on LS1012A based boards.
* tag 'imx-dt64-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: update the DPAA QBMan nodes
arm64: dts: ls1088a: add PCIe controller DT nodes
arm64: dts: ls1088a: add gicv3 ITS DT node
arm64: dts: ls2088a: add pcie support
arm64: dts: ls: Add optee node
dt-bindings: mtd: add sst25wf040b and en25s64 to sip-nor list
dt-bindings: spi: Add fsl,ls1012a-dspi compatible string
arm64: dts: ls1012a: add the DTS node for DSPI support
