Allow drivers to pass device-specific configuration parameters during attach.
If these parameters are omitted, default values will be used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move some common code to a new file to make this easier to look at.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested successfully with QAM256 digital cable.
Analog television is limping, needs more work.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
make set_analog_params function look consistent with set_params function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Older em28xx devices does implement standard Audio Class.
However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.
For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.
This patch uses the request_module_async function as defined on cx88-mpeg.c,
originally wrote by Markus Rechberger.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
em28xx-audio module exports em28xx Vendor Class audio as an -alsa
driver. This module were written based on usbaudio driver by Markus
Rechberger. Recently, he acked to allow us to merge it on kernel:
http://lists-archives.org/video4linux/20408-supporting-prolink-pixelview-405-dvd-maker.html
Thanks to Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those
commands.
Also, MTS firmware is required for audio to work on HVR950.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.
It also do some cleanups at audio setup configurations.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Break out the following new functions from tda18271_tune:
tda18271_calc_bp_filter
tda18271_calc_km
tda18271_calc_rf_band
tda18271_calc_gain_taper
tda18271_calc_ir_measure
tda18271_calc_rf_cal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We don't need to do a dbg_info during tda18271_attach anymore, since
the tda18271_get_id function will call dbg_info with the same information
and more.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following compiler error:
v4l2-i2c-drv.h:72: error: implicit declaration of function 'v4l2_i2c_attach'
Also, prevent multiple inclusions of v4l2-i2c-drv.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-core was checking if analog_ops->set_config is set. If set, it would
complain that it isn't. Fix this backwards logic to the proper behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Everybody forgets to add the Kconfig stuff after they add new card support :-/
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
bttv driver is working as previously. An additional gain of about 1,5Kb were
obtained with the driver conversion to vidioc_ioctl2:
text data bss dec hex filename
89208 40244 57556 187008 2da80 old/bttv.ko
88960 38740 57556 185256 2d3a8 new/bttv.ko
(measured on a x86_64)
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since there are a few vidioc_ functions that were exported, rename those
functions to bttv_ in order to avoid poluting namespace.
The other functions were also renamed, to standardize inside the driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't allow the tda8290 module to probe and attach the tuner module,
causing incorrect use counts when using dvb_attach.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prevent the tda8290 module from probing for tuners during tda829x_attach,
by passing:
.probe_tuner = TDA829X_DONT_PROBE,
...in struct tda829x_config
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Identify the silicon during attach, return NULL if unsupported device.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Bit 7 of both Main Divider byte 1 and Cal Divider byte 1 is always zero.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fixes all occurences of assignment in if
checkpatch marks them as ERROR.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Reviewed-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add module option 'alt_tuner' disabled by default.
When set to one, the dvb_frontend of HVR1800 will consist of:
s5h1409 demod + tda18271 tuner
When set zero (default), the dvb_frontend of HVR1800 will consist of:
s5h1409 demod + mt2131 tuner
If the tda18271 is used in digital mode, you will not be able to
tune an analog channel at the same time.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
