This clock has been missing since some early stages of device tree
conversion. Adding the right clocks to the device tree makes USB
work again.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The physical pins from the SoC are in a sense belonging to the
PHY device (AB8500 USB) rather than the MUSB USB IP block.
The driver definately assumes so: before this change it
complains that it cannot control the pins it is using:
abx5x0-usb ab8500-usb.0: could not get/set default pinstate
After this patch the warning goes away.
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the enable-active-high setting from the SoC to the
board for the VMMCQ regulators. It should at least be in the
vicinity of the GPIO line it is defined for.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Provide human readable names for all power domains defined in Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The ahci driver now supports other refclk clock rates.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Register a fixed rate clock modelling the external SATA oscillator
for da850 (both DT and board file mode).
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The ahci-da850 SATA driver is now capable of retrieving clocks by
con_id. Add the connection id for the sysclk2-derived SATA clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This merge is because patches in branch v4.11/soc conflict
with cleanup done as part of 0a5011673a ("ARM: davinci:
da850: coding style fix") that is already queued as a
non-critical fix.
These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.
[gregory.clement@free-electrons.com: fix topic and update Makefile]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.
[gregory.clement@free-electrons.com: fix topic]
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable the SATA node for da850-lcdk. We omit the pinctrl property on
purpose - the muxed SATA pins are not hooked up to anything
SATA-related on the lcdk.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
DTS files, which includes orion5x-linkstation.dtsi, are named:
orion5x-linkstation-*.dts
So we rename the file below:
arch/arm/boot/dts/orion5x-lschl.dts
to the new name:
arch/arm/boot/dts/orion5x-linkstation-lschl.dts
Because DTS conversion of this device was just introduced in 4.9, Debian
is still using legacy device support, other distros are the same,
so here we won't expect any impact actually.
Fixes: f94f268979 ("ARM: dts: orion5x: convert ls-chl to FDT")
Cc: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Model name should be consistent with legacy device file, so that user
can migrate their system from legacy device support to device-tree
safely.
Legacy device file is currently removed, but it can be found on 4.8
or previous version of linux:
arch/arm/mach-orion5x/ls-chl-setup.c
Fixes: f94f268979 ("ARM: dts: orion5x: convert ls-chl to FDT")
Cc: Ashley Hughes <ashley.hughes@blueyonder.co.uk>
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This entry is needed for the ahci driver to get a functional clock.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add the da850-ahci driver to davinci defconfig.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Add a DT binding documentation for the Video Data Order Adapter (VDOA)
of the Freescale i.MX6 SoC.
Also, add the compatible property and correct clock to the device tree
to match the documentation.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
As reported by kernel build test:
In file included from arch/arm/mach-omap2/pdata-quirks.c:15:0:
>> arch/arm/mach-omap2/pdata-quirks.c:536:49: error: 'rx51_lirc_data' undeclared here (not in a function)
OF_DEV_AUXDATA("nokia,n900-ir", 0, "n900-ir", &rx51_lirc_data),
^
include/linux/of_platform.h:52:21: note: in definition of macro 'OF_DEV_AUXDATA'
.platform_data = _pdata }
^~~~~~
Since "a92def1 [media] ir-rx51: port to rc-core" the build fails on
some arm configurations.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
This driver was written using lirc since rc-core did not support
transmitter-only hardware at that time. Now that it does, port
this driver.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
KVM_MEMSLOT_INCOHERENT is not used anymore, as we've killed its
only use in the arm/arm64 MMU code. Let's remove the last artifacts.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Now that we unconditionally flush newly mapped pages to the PoC,
there is no need to care about the "uncached" status of individual
pages - they must all be visible all the way down.
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
When we fault in a page, we flush it to the PoC (Point of Coherency)
if the faulting vcpu has its own caches off, so that it can observe
the page we just brought it.
But if the vcpu has its caches on, we skip that step. Bad things
happen when *another* vcpu tries to access that page with its own
caches disabled. At that point, there is no garantee that the
data has made it to the PoC, and we access stale data.
The obvious fix is to always flush to PoC when a page is faulted
in, no matter what the state of the vcpu is.
Cc: stable@vger.kernel.org
Fixes: 2d58b733c8 ("arm64: KVM: force cache clean on page fault when caches are off")
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Userspace requires to store and restore of line_level for
level triggered interrupts using ioctl KVM_DEV_ARM_VGIC_GRP_LEVEL_INFO.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 CPU interface registers are accessed using
KVM_DEV_ARM_VGIC_CPU_SYSREGS ioctl. These registers are accessed
as 64-bit. The cpu MPIDR value is passed along with register id.
It is used to identify the cpu for registers access.
The VM that supports SEIs expect it on destination machine to handle
guest aborts and hence checked for ICC_CTLR_EL1.SEIS compatibility.
Similarly, VM that supports Affinity Level 3 that is required for AArch64
mode, is required to be supported on destination machine. Hence checked
for ICC_CTLR_EL1.A3V compatibility.
The arch/arm64/kvm/vgic-sys-reg-v3.c handles read and write of VGIC
CPU registers for AArch64.
For AArch32 mode, arch/arm/kvm/vgic-v3-coproc.c file is created but
APIs are not implemented.
Updated arch/arm/include/uapi/asm/kvm.h with new definitions
required to compile for AArch32.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
VGICv3 Distributor and Redistributor registers are accessed using
KVM_DEV_ARM_VGIC_GRP_DIST_REGS and KVM_DEV_ARM_VGIC_GRP_REDIST_REGS
with KVM_SET_DEVICE_ATTR and KVM_GET_DEVICE_ATTR ioctls.
These registers are accessed as 32-bit and cpu mpidr
value passed along with register offset is used to identify the
cpu for redistributor registers access.
The version of VGIC v3 specification is defined here
Documentation/virtual/kvm/devices/arm-vgic-v3.txt
Also update arch/arm/include/uapi/asm/kvm.h to compile for
AArch32 mode.
Signed-off-by: Vijaya Kumar K <Vijaya.Kumar@cavium.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Compared to the armada-xp the 98DX3336 uses different registers to set
the boot address for the secondary CPU so a new enable-method is needed.
This will only work if the machine definition doesn't define an overall
smp_ops because there is not currently a way of overriding this from the
device tree if it is set in the machine definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Ensure that if userspace supplies insufficient data to
PTRACE_SETREGSET to fill all the registers, the thread's old
registers are preserved.
Cc: <stable@vger.kernel.org> # 3.0.x-
Fixes: 5be6f62b00 ("ARM: 6883/1: ptrace: Migrate to regsets framework")
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Asynchronous external abort is coded differently in DFSR with LPAE enabled.
Fixes: 9254970c "ARM: 8447/1: catch pending imprecise abort on unmask".
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates dev_pm_opp_find_freq_*() routines to get a reference
to the OPPs returned by them.
Also updates the users of dev_pm_opp_find_freq_*() routines to call
dev_pm_opp_put() after they are done using the OPPs.
As it is guaranteed the that OPPs wouldn't get freed while being used,
the RCU read side locking present with the users isn't required anymore.
Drop it as well.
This patch also updates all users of devfreq_recommended_opp() which was
returning an OPP received from the OPP core.
Note that some of the OPP core routines have gained
rcu_read_{lock|unlock}() calls, as those still use RCU specific APIs
within them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com> [Devfreq]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that we have a full clock driver for sun9i, switch to it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
1. Remove mach code for Exynos4415 as a continuation of removal
of this SoC.
2. Remove obsolete property from the bindings documentation.
-----BEGIN PGP SIGNATURE-----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=kl+X
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/soc
Samsung mach/soc update for v4.11, second round:
1. Remove mach code for Exynos4415 as a continuation of removal
of this SoC.
2. Remove obsolete property from the bindings documentation.
* tag 'samsung-soc-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
dt-bindings: video: exynos7-decon: Remove obsolete samsung,power-domain property
ARM: EXYNOS: Remove Exynos4415 arch code (SoC not supported anymore)
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Use bigger reserved memory region for Multi Format Codec on all Exynos
chipsets so it could decode FullHD easily.
-----BEGIN PGP SIGNATURE-----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=E4FL
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Samsung DeviceTree update for v4.11, second round:
1. Use bigger reserved memory region for Multi Format Codec on all Exynos
chipsets so it could decode FullHD easily.
* tag 'samsung-dt-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix indentation of EHCI and OHCI ports
ARM: dts: exynos: Increase MFC left reserved memory region size
Signed-off-by: Olof Johansson <olof@lixom.net>
1. Add support for Exynos5433 to Power Management Unit (PMU) and Power
Domains drivers.
2. Cleanups of duplicated and unused defines.
-----BEGIN PGP SIGNATURE-----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=pXm9
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-soc-pmu-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Continuation of improvements for Exynos PM drivers for v4.11:
1. Add support for Exynos5433 to Power Management Unit (PMU) and Power
Domains drivers.
2. Cleanups of duplicated and unused defines.
* tag 'samsung-drivers-soc-pmu-4.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Remove duplicated define for ARM_L2_OPTION register
soc: samsung: pmu: Remove unused and duplicated defines
soc: samsung: pm_domains: Add new Exynos5433 compatible
soc: samsung: pmu: Add dummy support for Exynos5433 SoC
Signed-off-by: Olof Johansson <olof@lixom.net>
- Select wireless extensions option for imx_v6_v7_defconfig, so that
wireless works out of box with userspace tools such as 'iwconfig'.
- Enable EXT4 filesystem support for vf610m4_defconfig.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWf2AAoJEFBXWFqHsHzOSicH/Rg+X7Qat+pMxINB7+enJqlw
mIM5WTUwhO4txugFD84ybcBitC/+t/kS5ffEM7ckkDDn6p6bN0K9vcU137V/CkE2
cMHgnuawXs3qCu4D+h4X3MsdF/AWTOD20dv1W5QMhC9/kANP2emQ6ohB5Wee0Gmx
5Mi4UaD0QNYrFsukayWhQ45i0RbsNRdiyzAntIpY1Xz8JJGL/ufTk233wtfxihsV
8MQw/Ar1Q3Hz8+eIKj+9dqDKV5AUrXQ3GvrvTfwlXlLM+NNSN5UWfJsbzob9754P
h02zRhjtQfjFKTUVAJKQPTNPci8b+8InnKyLgqSNSAnb/2PXtJB0AlFXJfaZ/LM=
=VjCo
-----END PGP SIGNATURE-----
Merge tag 'imx-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/defconfig
i.MX defconfig updates for 4.11:
- Select wireless extensions option for imx_v6_v7_defconfig, so that
wireless works out of box with userspace tools such as 'iwconfig'.
- Enable EXT4 filesystem support for vf610m4_defconfig.
* tag 'imx-defconfig-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: vf610m4: defconfig: enable EXT4 filesystem
ARM: imx_v6_v7_defconfig: Select wireless extensions option
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjWLQAAoJEFBXWFqHsHzOGt0H/2WCsuRi6WU7i7Wyk/S0Xq5t
HzA/9m2f7z1vb1tzFknbpcWYa9bdofI7Dz+6KW2vp4fxhMyJn8SQxWwQjVNya2ba
z8XLdEMlIuozBebPcH84ovNzqoBIOEFahGm5smm40s/o7XL8ua9tOEFaUc+jY0Pd
n/3TPmoyBTlbrgiCZfLXCVsczHtEVW5JoQmXT7aDsxT0BQpnwLbgXKVOxgDvsWXM
WtAKjpGvdiApD3znbFjYmRKak+2uilkV5B4jrL4mZf8dxCliykP4XA/LbiMLKAMN
voMpTtTK7UYp59GrwKbqfJ+pPU7b6ndKK59f7FWrTDNgtDGe+J4ExjWwsDnuLfI=
=HAbg
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX device tree updates for 4.11:
- New board support: vf610-zii-dev-rev-c, imx6ul-opos6uldev,
imx6ul-isiot, imx6qdl-savageboard, imx6q-mccmon6.
- A patch from Alexandre to correct the mangled license text which
has been copied & pasted all over the i.MX device tree files.
- Update cpu nodes of some i.MX SoCs to make them consistent and match
ePAPR spec.
- Add OCOTP device for i.MX6UL SoC.
- Add security violation interrupt for i.MX25 DryIce.
- Enable USB OTG, WIFI and Bluetooth support for i.MX6SX Udoo Neo
board.
- Enable S/PDIF and 2nd display pipeline support for CompuLab board..
- Add SPI and LTC3676 PMIC support for Gateworks Ventana boards.
- A few random device addition for various boards: TVE DAC regulators
for imx53-qsb, EEPROM for vf610-zii-dev, eMMC and NAND support for
i.MX6UL Engicam boards.
- Cleanups on obsoleted or unused properties.
* tag 'imx-dt-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (32 commits)
ARM: dts: udoo_neo: Add Bluetooth support
ARM: dts: udoo_neo: Add Wifi support
ARM: dts: udoo_neo: Add UDOO Neo USB OTG1 and OTG2 support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL NAND initial support
ARM: dts: imx6ul: Add Engicam Is.IoT MX6UL eMMC initial support
ARM: dts: imx6qdl: Fix "ERROR: code indent should use tabs where possible"
ARM: dts: vf610-zii-dev: add EEPROM entry to Rev C
ARM: dts: add Armadeus Systems OPOS6UL and OPOS6ULDEV support
ARM: dts: imx6q-utilite-pro: enable 2nd display pipeline
ARM: dts: vf610-zii-dev: Add .dts file for rev. C
ARM: dts: vf610-zii-dev-rev-b: Remove leftover PWM pingroup
ARM: dts: imx6: Support Savageboard quad
ARM: dts: imx6: Support Savageboard dual
ARM: dts: imx6: Add Savageboard common file
ARM: dts: imx53-qsb: Provide the TVE DAC regulators
ARM: dts: imx6q: Add mccmon6 board support
Doc: devicetree: bindings: Add vendor prefix entry - lwn
ARM: dts: imx/vf: Correct license text
ARM: dts: imx25.dtsi: DryIce security violation interrupt
ARM: dts: imx: Add ocotp node for imx6ul
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Remove unused flexcan and esdhc device definitions for i.MX25.
- A series from Fabio to remove camera device initialization code from
i.MX platform support, since the corresponding media driver has been
deprecated and removed from kernel tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjVZ8AAoJEFBXWFqHsHzOiW8IAKucWgP/WbNyi4AOJf7fyXts
USevVUrv5PMpeekb/EoLilYXNZaaUSnmx/zsAGfG2tBd94FPrDEFcDJLmEmBVKwO
fYxFEBddVJkT+zsXgAkffaEI447tV9Hgaxb91vqc25LKqj85uxzeo3t4YZadHO22
xFIc/hE3GDTiu0L4P0cqAE9hJl7pZGiENta0KZO6g8nvYpFvPddtfQ/GpbKGOJW1
9h/iMP4CbnTgU9pQkm/IwGopejsvWHzlCVrOPJz5Fj7B7Mrf6xQigo5ZovPnPF+m
GYp5C4wZ9oQCsIeaBLEKubgzJA+xXwp1TpzPbGdDPp5rqfsGEKfJiPnzNJK/x68=
=t+pS
-----END PGP SIGNATURE-----
Merge tag 'imx-cleanup-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
i.MX cleanup for 4.11:
- Remove unused flexcan and esdhc device definitions for i.MX25.
- A series from Fabio to remove camera device initialization code from
i.MX platform support, since the corresponding media driver has been
deprecated and removed from kernel tree.
* tag 'imx-cleanup-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: mach-mx27_3ds: Remove camera support
ARM: mach-pcm037: Remove camera support
ARM: mach-mx35_3ds: Remove camera support
ARM: mx31moboard-smartbot: Remove camera support
ARM: mx31moboard-marxbot: Remove camera support
ARM: mach-mx31_3ds: Remove camera support
ARM: imx: remove unused device definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
- A couple of fixes on anatop regulator voltage and constraints
according to hardware datasheet.
- Correct FEC interrupt routing for i.MX6QP which has got the hardware
bug found on i.MX6Q fixed.
- Remove unit address from i.MX6 LDB device node to fix DTC warning.
- A fix on imx53-qsb board FEC pinmux config to remove the dependency
on firmware for setting up pins.
- A series from Sascha to fix LPSR pins for i.MX7 boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYjVP+AAoJEFBXWFqHsHzOcvEIAKmxLYG5bmXkUNm+cJQ0oJde
MPh984lN1Xzx0PFlXJoC3mMC4W0RCibLjjSMS3s28ddzw0AKyAWHVkPDzUtuFQOT
s7iUjgXhfpwxeIt5DGZUXbzfZVXjRrVgWfYSMPnc2Q+PUAHQDhqTqylCTz5yF6qf
/XpN5uBaq/h++CJ+e06h9xSuIaCcEtGzLoUA+qXJBseBCLxlaR7zlt5bVL338oOt
P8LuKk8Xcmc6QstpC5HyH8XuHQ8h+Gj0tLKkFeEnLY5JFmRo6e1wOq9EPW+AHfBp
vgW5cI5cgdtn7/TuAbmCOoE052jd8oVK3LnKEfFXHxcBCDIDYz580CdbTFe06+g=
=tRE+
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-nc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
i.MX non-critical device tree fixes for 4.11:
- A couple of fixes on anatop regulator voltage and constraints
according to hardware datasheet.
- Correct FEC interrupt routing for i.MX6QP which has got the hardware
bug found on i.MX6Q fixed.
- Remove unit address from i.MX6 LDB device node to fix DTC warning.
- A fix on imx53-qsb board FEC pinmux config to remove the dependency
on firmware for setting up pins.
- A series from Sascha to fix LPSR pins for i.MX7 boards.
* tag 'imx-fixes-nc-4.11' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx53-qsb-common: fix FEC pinmux config
ARM: imx6: remove unit address from LDB node
ARM: imx6qp: adapt DT to changed FEC interrupts
ARM: imx6: fix regulator constraints on anatop 1p1 and 2p5
ARM: imx6: fix min/max voltage of anatop 2p5 regulator
ARM: dts: imx7: Add "LPSR" to LPSR iomux pin names
ARM: dts: imx7d-cl-som: Fix OTG power pinctrl
ARM: dts: imx7d-sdb: Fix watchdog and pwm pinmux
ARM: dts: imx7s-warp: Fix watchdog pinmux
Signed-off-by: Olof Johansson <olof@lixom.net>
Switch device tree files to the new DSA binding
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWIt8ZyMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71fx4AJ4mibAO0PUJ
Hbts4+PNC5f8PMYHlQCeIDfqtqLKlfJMVH3YFasSLYmb0lo=
=PRxv
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-4.11-2' of git://git.infradead.org/linux-mvebu into next/dt
mvebu dt for 4.11 (part 2)
Switch device tree files to the new DSA binding
* tag 'mvebu-dt-4.11-2' of git://git.infradead.org/linux-mvebu:
ARM: dts: kirkwood-rd88f6281: Utilize new DSA binding
ARM: dts: kirkwood-mv88f6281gtw-ge: Utilize new DSA binding
ARM: dts: kirkwood-linksys-viper: Utilize new DSA binding
ARM: dts: kirkwood-dir665: Utilize new DSA binding
ARM: dts: armada-xp-linksys-mamba: Utilize new DSA binding
ARM: dts: armada-388-clearfog: Utilize new DSA binding
ARM: dts: armada-385-linksys: Utilize new DSA binding
ARM: dts: armada-370-rd: Utilize new DSA binding
Signed-off-by: Olof Johansson <olof@lixom.net>
Cleanup up on dove pmu and mv78x00 pci
-----BEGIN PGP SIGNATURE-----
iIEEABECAEEWIQQYqXDMF3cvSLY+g9cLBhiOFHI71QUCWIt76SMcZ3JlZ29yeS5j
bGVtZW50QGZyZWUtZWxlY3Ryb25zLmNvbQAKCRALBhiOFHI71ei+AKCfHdyZYwW1
uRXvVqdkSgOYQ8hAiwCfd2NeIfkr/7rEufrswNvqcmVc078=
=FdKA
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.11-1' of git://git.infradead.org/linux-mvebu into next/soc
mvebu soc for 4.11 (part 1)
Cleanup up on dove pmu and mv78x00 pci
* tag 'mvebu-soc-4.11-1' of git://git.infradead.org/linux-mvebu:
soc: dove: constify reset_control_ops structures
ARM: mv78xx0: fix possible PCI buffer overflow
Signed-off-by: Olof Johansson <olof@lixom.net>
Since v4.10-rc1, xhci is complaining in loop with :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
set property "snps,dis_u3_susphy_quirk" in DT fix it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+Frf
-----END PGP SIGNATURE-----
Merge tag 'sti-dt-for-v4.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti into fixes
STi DT fix:
Since v4.10-rc1, xhci is complaining in loop with :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
set property "snps,dis_u3_susphy_quirk" in DT fix it.
* tag 'sti-dt-for-v4.10-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
ARM: dts: STiH407-family: set snps,dis_u3_susphy_quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a set of patches that add hardware compatibility for newer
revisions of the Toradex Apalis TK1. Also included is a fix to the PAZ00
that stabilizes panel initialization on boot as well as a patch to add
card detection for the µSD card slot on TrimSlice.
To round things off there are a couple of fixes and changes to the Nyan
device tree files to fix the battery charger, add compatibility with new
revisions of Nyan Blaze and Nyan Big, as well as properly support the
TPM.
-----BEGIN PGP SIGNATURE-----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=QqnB
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
ARM: tegra: Device tree changes for v4.11-rc1
This contains a set of patches that add hardware compatibility for newer
revisions of the Toradex Apalis TK1. Also included is a fix to the PAZ00
that stabilizes panel initialization on boot as well as a patch to add
card detection for the µSD card slot on TrimSlice.
To round things off there are a couple of fixes and changes to the Nyan
device tree files to fix the battery charger, add compatibility with new
revisions of Nyan Blaze and Nyan Big, as well as properly support the
TPM.
* tag 'tegra-for-4.11-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: nyan-blaze: Proper pinmux for TPM I2C
ARM: tegra: nyan-big: Proper pinmux for TPM I2C
ARM: tegra: nyan-blaze: Include compatible revisions for proper detection
ARM: tegra: nyan-big: Include compatible revisions for proper detection
ARM: tegra: nyan: Use external control for bq24735 charger
ARM: tegra: nyan: Use proper IRQ type definitions
ARM: dts: tegra: Fix missing card detection in Trimslice µSD card slot
ARM: tegra: paz00: Mark panel regulator as enabled on boot
ARM: tegra: apalis-tk1: Update compatibility comment
ARM: tegra: apalis-tk1: Fix SD card detect on v1.1 HW
ARM: tegra: apalis-tk1: Adjust pin muxing for v1.1 HW
ARM: tegra: apalis-tk1: Optional DisplayPort hot-plug detect
ARM: tegra: apalis-tk1: Pull-up temperature alert
Signed-off-by: Olof Johansson <olof@lixom.net>
This contains a single cleanup patch for the placement of the __initdata
annotation, as suggested by checkpatch.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAliLDTMTHHRyZWRpbmdA
bnZpZGlhLmNvbQAKCRDdI6zXfz6zofCHEADCEKzpctp7yZcjm+CJmyQ8BQnvh/Lu
D7Rpa1fZaojZVuRHbAHvtbzWibybQVC+CYQqVALl75IpPdTJcBaON8sk2OEXI+2j
5OUU3xRrCUaOeMEIyAbGdVYpU9PQdP08S4dUVMrDhXod1XkPa+luQ3ojPBfelll5
XfG/xqos32jJ4iSBd8hr1U1g80MgFPNQasloaB6W4oLvUXnye/G4vgT6MVICm8d1
hQRS0KU9hK1pR4YoebH4/vO2jMRuBPSKGem/DBx9jnxrE8oqMyLGOKt5sxffI2DI
UHtn4o2Y8uaHrCmdIdVZ9Frvp76+iINI5jqO6rTrhF2Jhd5V+eXXFLB9yGOHPpIl
uxyZpou6cOfMQ5aclYEHeLP1BNboA6sMNt2YagKQVdGBL8d4WsWcCwzUvkAbghVq
3wQxp7vQ4ZD6bPZj22EtprchECCcIWqwo7AWMNr3CnL/wyNCrdRwesjVUwVnLOlO
9Lb2XpJEF435setIU7jOW+7fUAhC3AqBZ2jj98fOHFMjDspnGNhr4PCqkPk7glHv
b+jQvV5cRkiojrTz68FoeWMrFb7afL4CgYUUdfvNUO0yChHwsL+CS6q7LrEuYMAE
3Ub73Jjgie/gZlqSqcTKBDHgs9iKx3HdmJUrPziCdha+wKU9/bNUtFWfvH+KE/SE
BZaboFE8N2oJZw==
=NF/K
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
ARM: tegra: Core SoC changes for v4.11-rc1
This contains a single cleanup patch for the placement of the __initdata
annotation, as suggested by checkpatch.
* tag 'tegra-for-4.11-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: paz00: Fix __initdata placement
Signed-off-by: Olof Johansson <olof@lixom.net>
- Enable the DMA on sama5d2 and sama5d4 xplained to fix an issue seen by
kernelci
-----BEGIN PGP SIGNATURE-----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=MsBR
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT for 4.11 #2:
- Enable the DMA on sama5d2 and sama5d4 xplained to fix an issue seen by
kernelci
* tag 'at91-ab-4.11-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: Enable DMA on sama5d2_xplained console
ARM: dts: at91: Enable DMA on sama5d4_xplained console
Signed-off-by: Olof Johansson <olof@lixom.net>
* Add more register documentation to R-Car Gen2 PM
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WcAl
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/soc
Second Round of Renesas ARM Based SoC Updates for v4.11
* Add more register documentation to R-Car Gen2 PM
* tag 'renesas-soc2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: rcar-gen2: Add more register documentation
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhancements:
* Add power-domains to mmcif on r7s72100 SoC
* Add OSTM to rskrza1/r7s72100
* Link ARM GIC to clock and clock domain on r8a774[35] SoCs
Clean-up:
* Correct SATA device status on r8a7779/marzen
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=5/D6
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.11
Enhancements:
- Add power-domains to mmcif on r7s72100 SoC
- Add OSTM to rskrza1/r7s72100
- Link ARM GIC to clock and clock domain on r8a774[35] SoCs
Clean-up:
- Correct SATA device status on r8a7779/marzen
* tag 'renesas-dt2-for-v4.11' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: dts: r7s72100: add power-domains to mmcif
ARM: dts: rskrza1: add ostm DT support
ARM: dts: r7s72100: add ostm to device tree
ARM: dts: r7s72100: add ostm clock to device tree
ARM: dts: r8a7745: Link ARM GIC to clock and clock domain
ARM: dts: r8a7743: Link ARM GIC to clock and clock domain
ARM: dts: r8a7779, marzen: Fix sata device status
Signed-off-by: Olof Johansson <olof@lixom.net>
This cycle is a minor fixes one, covering :
- build fixes from Arnd, mainly include related
- transfer of maintainance of Motorala phone to Robert
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Z3AX
-----END PGP SIGNATURE-----
Merge tag 'pxa-for-4.11' of https://github.com/rjarzmik/linux into next/soc
This is the pxa changes for v4.11 cycle.
This cycle is a minor fixes one, covering :
- build fixes from Arnd, mainly include related
- transfer of maintainance of Motorala phone to Robert
* tag 'pxa-for-4.11' of https://github.com/rjarzmik/linux:
MAINTAINERS: transfer maintainership for the EZX platform
ARM: pxa: include linux/leds.h
ARM: pxa: ezx: fix a910 camera data
Signed-off-by: Olof Johansson <olof@lixom.net>
- Drop the declaration of the unimplemented hip01_cpu_die
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJYiNOBAAoJEAvIV27ZiWZcmkIP/jiTcu/KpJDKbhsf04QKvlNr
lHxcH+PuBpvp33Emw2b17dyKqRq5+74LtxShxVIW3KLBipi1w9dsHhlFc1QfnFNb
lxZNvhIOWJshHsnu9Xn23Vbari1cxcpoEZe1R+6ij20UXdg282C7Zj3Hg8oHa5oB
eCGgoSxwnEqh55MmUOTSh+7GG1eSK/MExjZAI/nT8NUu2JIhLopAXCMJVZu3tUUz
BEOrz+76WC3KWkG7aFdBu10/7qRT++Wh2jirguxCEXo9SxaUs1i7G1DGzhy8N9oh
Vs2EKNdYTeKu9IMJAx2RFEcxEusc+oAfTLQBQCSQFaKYKp+K+ZZ3pKF6E7LT1AyL
Sz/xQETtWNjETgE5YVXwfHUlZOB7k9/2q/SoL9gqbQ+302Que1U6a+i747ZLmYH9
/N7HS1WLMLIGGvcp7X/iMwBqZAnVY+vi7KNiqGzRd2YYRnJ/L44fTbEIB/Ve5tvT
vj81yKTLx228VJM9IB0F2Sz6KXsJeW2TcNk2sF88TfGx80FTmxFfdK1lHNQXQWcu
4aRG2o2np3PFXCn1pGW1KoVvvhhnzFRcXQSXlRQTOcc/SBOK9E1hOCvEf3eG0cdj
TSRLbvlg2Gs7BdX8O4axNoN9nbXD1MvF6yuAgbxdavgJGUx72Eq7J7ebzUXNFwTh
nxhqaOtpmPyigm8aS2nb
=XY+A
-----END PGP SIGNATURE-----
Merge tag 'hisi-armv7-soc-for-4.11' of git://github.com/hisilicon/linux-hisi into next/soc
ARM: mach-hisi: Hisilicon SoC updates for 4.11
- Drop the declaration of the unimplemented hip01_cpu_die
* tag 'hisi-armv7-soc-for-4.11' of git://github.com/hisilicon/linux-hisi:
arm: hisi: drop extern hip01_cpu_die
Signed-off-by: Olof Johansson <olof@lixom.net>
- Switch to use LIS3LV02DL IIO driver instead of the
LIS3LC02D misc driver
- Set CONFIG_SERIAL_8250_RUNTIME_UARTS=6 to avoid runtime
warnings on omap5 and dra7
- Enable ksz9021 phy and m41t80 rtc as they are used at
least on phyCORE-AM335x
-----BEGIN PGP SIGNATURE-----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=Vv0t
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/defconfig
Few omap2plus_defconfig changes for v4.11 merge window:
- Switch to use LIS3LV02DL IIO driver instead of the
LIS3LC02D misc driver
- Set CONFIG_SERIAL_8250_RUNTIME_UARTS=6 to avoid runtime
warnings on omap5 and dra7
- Enable ksz9021 phy and m41t80 rtc as they are used at
least on phyCORE-AM335x
* tag 'omap-for-v4.11/defconfig-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: omap2plus_defconfig: Enable support for RTC M41T80
ARM: omap2plus_defconfig: Enable support for micrell phys
ARM: omap2plus_defconfig: Fix probe errors on UARTs 5 and 6
ARM: defconfig: omap2plus: switch LIS3LV02DL driver
Signed-off-by: Olof Johansson <olof@lixom.net>
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:
- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
eth phys, add pinmux configuration for mmc, remov erratum
i869 pinmux configurations, disable NAND support because of
pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata
-----BEGIN PGP SIGNATURE-----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=URbm
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.11 merge window. These
changes add earlycon stdout-path propety for the SoCs so far
tested with it. The other changes are addition of BeagleBone
green and making WLAN work on BeagleBone black wireless and
green wireless. The rest of the changes are the usual enabling
features on various devices:
- Enable devices on am335x-sl50
- Changes to dra7-evm boards to enable enable irqs for dp83867
eth phys, add pinmux configuration for mmc, remov erratum
i869 pinmux configurations, disable NAND support because of
pin conflict, add pcf8575 used for lcd
- Remove NAND partition table for omap3-igep
- Configure USB Ethernet MAC from device tree for beagleboard
xm, pandaboard, omap5-uevm and igepv5
- Configure am335x-chilisom to wake from RTC-only state
- Update Nanobone for external FRAM chip
- Clean up n900 dts
- Update am335x-phycore and am335x-wega for various devices
- Changes for am57xx-beagle-x15 to implement rgmii2 errata
* tag 'omap-for-v4.11/dt-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (35 commits)
ARM: dts: dra72/1-evm: add pcf8575 used for lcd
ARM: dts: dra7xx: Add stdout-path property
ARM: dts: am57xx: Add stdout-path property
ARM: dts: am43xx: Add stdout-path property
ARM: dts: am33xx: Add stdout-path property
ARM: dts: am335x-sl50: Enable the Ambient Light Sensor.
ARM: dts: am335x-sl50: Enable the MCP23017 GPIO Expander.
ARM: dts: am335x-sl50: Enable BQ32000 Real Time Clock.
ARM: dts: am335x-sl50: Enable SPI0 interface and Flash Memory.
ARM: dts: am335x-sl50: Enable UART1.
ARM: dts: am335x-sl50: Remove I2C1 node.
ARM: dts: omap3-igep: Remove NAND partition table
ARM: dts: am57xx-beagle-x15: implement errata "Ethernet RGMII2 Limited to 10/100 Mbps"
ARM: dts: am335x-phycore-som: Remove partition tables
ARM: dts: dra72-evm-revc: enable irqs for dp83867 eth phys
ARM: dts: Configure BeagleBone peripheral USB VBUS irq
ARM: dts: omap5-igep0050: Allow bootloader to configure USB Ethernet MAC
ARM: dts: omap5-uevm: Allow bootloader to configure USB Ethernet MAC
ARM: dts: pandaboard: Allow bootloader to configure USB Ethernet MAC
ARM: omap3: beagleboard-xm: dt: Add ethernet to the device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
for keeping the interconnect target module active for uart if
earlycon is specified. And we're adding Aaro Koskinen as a
co-maintainer for omap1 to make sure things stay working for
omap1. The other changes are mostly clean-up of old legacy code:
- Remove unused omap_display_init()
- Make omapdss_find_dss_of_node() function static
- Add support for earlycon
- Tidy up omap1 usb logging output with pr_cont
- Make omap_otg_init() static
- Delete redundant CPU class checks for omap1
- Remove unused mpurate cmdline option that has not done
anything for past 1.5 years at least
-----BEGIN PGP SIGNATURE-----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=GiAL
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/soc
SoC changes for omaps for v4.11 merge window. This adds support
for keeping the interconnect target module active for uart if
earlycon is specified. And we're adding Aaro Koskinen as a
co-maintainer for omap1 to make sure things stay working for
omap1. The other changes are mostly clean-up of old legacy code:
- Remove unused omap_display_init()
- Make omapdss_find_dss_of_node() function static
- Add support for earlycon
- Tidy up omap1 usb logging output with pr_cont
- Make omap_otg_init() static
- Delete redundant CPU class checks for omap1
- Remove unused mpurate cmdline option that has not done
anything for past 1.5 years at least
* tag 'omap-for-v4.11/soc-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: clock: Remove unused mpurate cmdline option
ARM: OMAP2+: omap_hwmod: Add support for earlycon
MAINTAINERS: Add Aaro Koskinen as TI omap1 SoC co-maintainer
ARM: OMAP1: USB: delete redundant CPU class checks
ARM: OMAP1: USB: make omap_otg_init() static
ARM: OMAP1: USB: tidy up logging output
ARM: OMAP2+: Make the omapdss_find_dss_of_node() function static
ARM: OMAP2+: Remove unused omap_display_init() function
Signed-off-by: Olof Johansson <olof@lixom.net>
fixes for things that have never worked or have been broken for
a long time and nobody noticed:
- Fix omap3 off mode pull defines
- Allow multiple pdata quirks instead of just one
- Fix am335x and dm814x scm syscon to probe children too
- Fix compatible for ti81xx to allow use with 8250_omap as well
- Fix 8250_omap on omap5 by adding HWMOD_SWSUP_SIDLE_ACT flag
- Fix SoC detection for omap36/37 SoCs
-----BEGIN PGP SIGNATURE-----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=SNQE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.11/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Non-urgent fixes for omaps for v4.11 merge window. These all are
fixes for things that have never worked or have been broken for
a long time and nobody noticed:
- Fix omap3 off mode pull defines
- Allow multiple pdata quirks instead of just one
- Fix am335x and dm814x scm syscon to probe children too
- Fix compatible for ti81xx to allow use with 8250_omap as well
- Fix 8250_omap on omap5 by adding HWMOD_SWSUP_SIDLE_ACT flag
- Fix SoC detection for omap36/37 SoCs
* tag 'omap-for-v4.11/fixes-not-urgent-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix SoC detection of OMAP36/37 Family
ARM: OMAP5: Add HWMOD_SWSUP_SIDLE_ACT flag for UART
ARM: dts: Fix compatible for ti81xx uarts for 8250
ARM: dts: Fix am335x and dm814x scm syscon to probe children
ARM: OMAP2+: Fix init for multiple quirks for the same SoC
ARM: dts: Fix omap3 off mode pull defines
Signed-off-by: Olof Johansson <olof@lixom.net>
Import a minimal defconfig for tango4 boards.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliBUsIQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgZKBB/9BVOysNvR/vLcao9jlU/an7c5vAwBdDl/G
uvsAgVAYRT2FUPcy7LPIQCoQOkk9HA3kMwiKVJH+hGQ+/0FdrKZvKkln/Yb/bT+9
GgQT2NblgNNDMfE76xQM0c7Y7Kj1oDrkGaAmdumnUPOSwMnSlxKD5j3fS2k4fz/t
ZOnqHxfEVDldmPIe4C58X5aqsQ4OmAgE7uiykZ4P3Vc0le71/QtJ4jsx4kkXNh9l
1+tGDfc1axmze/rEohw+BbNm3H5l8xMKFURlNE1Sr4dbW1y4o99mG7JVuxxfAQqd
XYP76I2foNtaxKgW29sQs0vopw9UimUiIH9i8xu4UsOWoj6N29Gj
=B1HN
-----END PGP SIGNATURE-----
Merge tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Bit of cleanup for the cortex-a9 uarts to have that soc-specific
spare-compatible as all others have, conversion to gpio constants
and addition of rk3288 qos nodes that need to be saved before a
power-domain gets turned off.
* tag 'v4.11-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add soc-specific uart compatibles for rk3066/rk3188
ARM: dts: rockchip: use pin constants to describe gpios
ARM: dts: rockchip: add qos node for rk3288
Signed-off-by: Olof Johansson <olof@lixom.net>
hiword registers (write-mask in upper 16bit) and domain-definitions
for the rk3328 soc.
Secondly a "driver" that attaches to the already existing grf nodes
and is able to set static defaults for settings that cannot really
be attached to any specific subsystem.
Most GRF settings can already be set from drivers using them, but there
are some behavioural settings like the mmc/jtag switch that cannot.
As the commit message states this is really meant as a last line
of defence for things that neither belong to a subsystem nor to the
Having this here allows arm64 socs to have this as well and also
moves another bit of code out of the arm32 mach-rockchip.
-----BEGIN PGP SIGNATURE-----
iQFEBAABCAAuFiEE7v+35S2Q1vLNA3Lx86Z5yZzRHYEFAliBTccQHGhlaWtvQHNu
dGVjaC5kZQAKCRDzpnnJnNEdgdMAB/42pPY0pKqOWlAfqzTSlIh98vi9jp0nZUu+
6RMlaqewhHq/zbH0qqJdcBrYRZF+EmJpTDGG2nltNi8FLNMyr+y7a0FVyjk/u43L
FnYELcDm7yeCZ0012ZP/4hlhWI9YizojbIKH4p2o8nIj64CS132ZMVVgojyzvVc1
0WLWUf8FBiMqsBpa6Kl117pvKayagk79PM570Ee2kRBxanN8yQaKmXTqG670eKzo
7nar1VGAubAVpCZfbv4opugGfrjYPJFX4gcu3yJvtRRN+hTt6idRP40YoCMZSVds
+okL0XW4G70ioXqZBS59Wq5FJS7frr8HRJbYD8lZg2vF948ZQnbC
=4aXM
-----END PGP SIGNATURE-----
Merge tag 'v4.11-armsoc-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Some extensions to the power-domain driver to support domains in
hiword registers (write-mask in upper 16bit) and domain-definitions
for the rk3328 soc.
Secondly a "driver" that attaches to the already existing grf nodes
and is able to set static defaults for settings that cannot really
be attached to any specific subsystem.
Most GRF settings can already be set from drivers using them, but there
are some behavioural settings like the mmc/jtag switch that cannot.
As the commit message states this is really meant as a last line
of defence for things that neither belong to a subsystem nor to the
Having this here allows arm64 socs to have this as well and also
moves another bit of code out of the arm32 mach-rockchip.
* tag 'v4.11-armsoc-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: rockchip: drop rk3288 jtag/mmc switch handling
soc: rockchip: add driver handling grf setup
dt-bindings: add used but undocumented rockchip grf compatible values
soc: rockchip: power-domain: add power domain support for rk3328
dt-bindings: add binding for rk3328 power domains
dt-bindings: power: add RK3328 SoCs header for idle-request
soc: rockchip: power-domain: Support domain control in hiword-registers
Signed-off-by: Olof Johansson <olof@lixom.net>
Replace spaces with tabs in EHCI and OHCI ports indentation.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
The pinmux configuration in device tree was different from manual
muxing in <u-boot>/board/freescale/mx53loco/mx53loco.c
All pins were configured as NO_PAD_CTL(1 << 31), which was fine as the
bootloader already did the correct pinmuxing for us.
But recently u-boot is migrating to reuse device tree files from the
kernel tree, so it seems to be better to have the correct pinmuxing in
our files, too.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Bluetooth chip connected to the UART3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Udoo Neo has a TI WL1831 Wifi chip connected to the USDHC3 port.
Add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for micro USB (OTG1) and USB Host (OTG2) for UDOO Neo board.
Tested on a UDOO Neo Full board by mounting a mass storage device
on both ports.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The LDB has no reg property as it uses the IOMUX-GPR syscon to access
its registers. Remove the unit address from the DT node to make DT
compiler happy.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
On i.MX6QP the FEC interrupts are wired to the GPC, just like all other
device interrupts. This allows to FEC to wake the CPU from WFI, but for
this to work the kernel needs to know about the new IRQ routing.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix the min/max voltage constraints for the anatop 1p1 and 2p5
regulator to match the typical operating range mentioned in the
datasheet.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The regulation bound of this regulator are 2.1V to 2.875V, the
wrong DT values cause the driver to miscalculate the effective
voltage.
This isn't really an issue right now, as nobody actively changes
the regulator voltage, but better fix it now.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX7 has two iomux controllers. the iomuxc and the iomuxc_lpsr.
In a board dts we have to make sure that both controllers are supplied
with the correct pins. It's way too easy to do this wrong since only
a look into the reference manual can reveal which pins belong to which
controller. To make this clearer add "LPSR" to the pin names which
belong to the LPSR controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPIO01_IO05 is controlled by the LPSR iomux controller, so attach
the corresponding pin to this controller.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin and the pwm output pin are controlled by the
iomuxc_lpsr, not the regular iomux, so move the pins there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The watchdog pin is controlled by the iomuxc_lpsr, not the regular
iomux, so move it there.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The sizes of the MFC reserved memory regions for CMA are 16 MiB for the
left bank and 8 MiB for the right bank. But this isn't enough to decode
high resolution videos so increase the size for the left bank to 36 MiB
which is enough for 1080p (1920x1080).
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Enable the S/PDIF transmitter that is present on the Beelink X2 STB.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF transceiver controller block to the H3 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the SPDIF TX pin to the H3 dtsi.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
gcc-7.0 reports a potential array overflow:
arch/arm/mach-mv78xx0/pcie.c: In function 'mv78xx0_pcie_preinit':
arch/arm/mach-mv78xx0/pcie.c:81:4: error: output may be truncated before the last format character [-Werror=format-truncation=]
I haven't checked if this can actually happen, but making the
array one 32-bit word longer addresses the warning and makes
it completely safe.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- Fix a 'defined but not used' warning in MMDC driver when
CONFIG_PERF_EVENTS is disabled.
- Fix i.MX6DL device tree GPIO4_11 range setting.
- A bandaid fix for boot failure found on a couple of platforms due to
missing 'chosen' and 'memory' node.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYihihAAoJEFBXWFqHsHzOpUsH/2u6xsOfLENcJ4JhSm1Xk3An
rSbOrl2OcphdYLC8jx6abKHknS/Tv1oxRQWjpZRse6CONV0e5LGm129c1/ZpgBat
lC35ApK+uv9iPRQkmOKotOSWchOPr3jfmIeSxJnCTLtmQfOhDwfxbYfuZHooNa5t
Ql0qD3wEc5+hjKGyNkWgFx7P+HmYB7m8BS/d4Daih6rQPtHGuIzf700SIpqQ+J40
/czLm0Ei0bJiOM8BwBFoHOhvqomkNWbMh5RR/lOhSwXdJ0EkEHXZ2196WEADEUbw
LuPHZqvihuZNSvdVfB5UoPjkpRPu4yTq12M9kGO9hxqN8QLBVE6VbcVonQEFlTo=
=QI4I
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into HEAD
Pull "i.MX fixes for 4.10, 3rd round" from Shawn Guo:
- Fix a 'defined but not used' warning in MMDC driver when
CONFIG_PERF_EVENTS is disabled.
- Fix i.MX6DL device tree GPIO4_11 range setting.
- A bandaid fix for boot failure found on a couple of platforms due to
missing 'chosen' and 'memory' node.
* tag 'imx-fixes-4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx: Pass 'chosen' and 'memory' nodes
ARM: dts: imx6dl: fix GPIO4 range
ARM: imx: hide unused variable in #ifdef
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The datasheet provided by Allwinner requires oscillators with an accuracy
of 50ppm. Add it to our fixed clocks so that we can properly track the
accuracy chain.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
So far, the LOSC was generated through the RTC internal oscillator, which
was a pretty poor and inaccurate choice.
Now that the RTC properly exposes its internal mux between its oscillator
and the external oscillator, we can use it were relevant.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lichee Pi Zero is a small-sized V3s board, which is
breadboard-compatible, and with a MicroUSB port with both OTG function
and power function.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As we have the pinctrl and clock support for the V3s SoC, it's now to
run a mainline Linux on it.
So add a .dtsi file for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
[Maxime: Removed the dependency on the CCU headers]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Since v4.10-rc1, the following logs appears in loop :
[ 801.953836] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 801.960455] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 801.966611] usb usb6-port1: cannot disable (err = -32)
[ 806.083772] usb usb6-port1: Cannot enable. Maybe the USB cable is bad?
[ 806.090370] xhci-hcd xhci-hcd.0.auto: Cannot set link state.
[ 806.096494] usb usb6-port1: cannot disable (err = -32)
After analysis, xhci try to set link in U3 and returns an error.
Using snps,dis_u3_susphy_quirk fix this issue.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The register ARM_L2_OPTION (0x2608 in Exynos4 and Exynos5 PMU) was
defined twice. Both names were used in the Exynos542x code. Simplify
this.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
The phyCORE-AM335x development kit is a combination of the
phyCORE-AM335x SoM and a PCM-953 carrier board. The features
of the PCM-953 are:
* ETH phy on carrier board: 1x RGMII
* 1x CAN
* Up to 4x UART
* USB0 (otg)
* USB1 (host)
* SD slot
* User gpio-keys
* User LEDs
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves pad retention control from S5PV210 machine code to
Exynos pin controller driver. This helps to avoid possible ordering
and logical dependencies between machine and pin control code. Till
now it worked fine only because sys_ops for machine code and pin
controller were called in registration order.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
For mach-s5pv210:
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch moves pad retention control from PMU driver to Exynos pin
controller driver. This helps to avoid possible ordering and logical
dependencies between machine, PMU and pin control code. Till now it
worked fine only because sys_ops for PMU and pin controller were called
in registration order.
This is also a preparation for adding new features to Exynos pin
controller driver, like runtime power management and suspending
individual pin controllers, which might be a part of some power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the Arria10, because of hardware bug, watchdog0 cannot reliably trigger
a reset to the CPU. The workaround would be to use watchdog1 instead.
Also for watchdog1, there is a dependency on the bootloader to enable the
boot_clk source to be from the cb_intosc_hs_clk/2, versus from EOSC1. This
corresponds to the (SWCTRLBTCLKEN & SWCTRLBTCLKSEL) bits enabled in the
control register in the clock manager module of Arria10.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Add a file to debugfs to read the in-kernel state of the vgic. We don't
do any locking of the entire VGIC state while traversing all the IRQs,
so if the VM is running the user/developer may not see a quiesced state,
but should take care to pause the VM using facilities in user space for
that purpose.
We also don't support LPIs yet, but they can be added easily if needed.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: Jerome Coste <jerome.coste@etu.utc.fr>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This corrects the pinmux for accessing the TPM over the I2C line. Thus,
it allows correctly probing the module, that previously failed with I2C
errors.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-blaze board so that the dtb can be selected preferably.
Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Depthcharge (the payload used with cros devices) will attempt to detect
boards using their revision. This includes all the known revisions for
the nyan-big board so that the dtb can be selected preferably.
Defining compatibly revisions allows depthcharge to select the kernel
via the revision it detects instead of using the default kernel. This
allows having a FIT image with multiple kernels for multiple devices.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nyan boards come with an embedded controller that controls when to
enable and disable the charge. Thus, it should not be left up to the
kernel to handle that.
Using the ti,external-control property allows specifying this use-case.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This switches a few interrupt definitions that were using
GPIO_ACTIVE_HIGH as IRQ type, which is invalid.
This is mostly a cosmetic change, that doesn't affect any driver.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Card insertion and removal currently goes undetected. AFAIK there's no
way to generate interrupts on card changes in this slot, so use polling.
Signed-off-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Current U-Boot enables the display already. Marking the regulator as
enabled on boot fixes sporadic panel initialization failures.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Tested-by: Misha Komarovskiy <zombah@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Placement of attributes, such as __initdata, is standardized through the
checkpatch script. Fix up this instance to make checkpatch happy.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Now with the new V1.1A HW card detect being implemented update resp.
compatibility information.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Configure Apalis MMC1 D6 GPIO on SDMMC3_CLK_LB_IN as reserved function
without any pull-up/down.
Configure GPIO_PV2 as SD1_CD# according to latest V1.1 HW.
Leave SDMMC3_CLK_LB_OUT muxed as SDMMC3 with output driver enabled aka
not tristated and input driver enabled as well as it features some
magic properties even though the external loopback is disabled and the
internal loopback used as per SDMMC_VENDOR_MISC_CNTRL_0 register's
SDMMC_SPARE1 bits being set to 0xfffd according to the TRM! This pin is
now a not-connect on V1.1 HW in order to avoid any interference.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
These files were only including module.h for exception table
related functions. We've now separated that content out into its
own file "extable.h" so now move over to that and avoid all the
extra header content in module.h that we don't really need to compile
these files.
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Introduce a new architecture-specific get_arch_dma_ops() function
that takes a struct bus_type * argument. Add get_dma_ops() in
<linux/dma-mapping.h>.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
Now that all set_dma_ops() implementations are identical (ignoring
BUG_ON() statements), remove the architecture specific definitions
and add a definition in <linux/dma-mapping.h>.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Chris Metcalf <cmetcalf@mellanox.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: linux-arch@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some but not all architectures provide set_dma_ops(). Move dma_ops
from struct dev_archdata into struct device such that it becomes
possible on all architectures to configure dma_ops per device.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Juergen Gross <jgross@suse.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Russell King <linux@armlinux.org.uk>
Cc: x86@kernel.org
Signed-off-by: Doug Ledford <dledford@redhat.com>
The 'mpurate' option, historically used for specifying an initial
MPU rate at boot, no longer has any effect due to the supporting
code being removed as it was 'wrong and dangerous' [1].
This patch removes the remaining dead code associated with the
__setup macros to avoid confusion and reduce bloat.
[1] https://patchwork.kernel.org/patch/5954631/
Signed-off-by: Andrew Murray <amurray@embedded-bits.co.uk>
Acked-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x SoM has a RV4162 RTC populated which is supported
by the M41T80 driver. Enabled it so make the RTC support on the SoM
available.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The phyCORE-AM335x SoM with PCM-953 carrierboard has a
KSZ9021 phy mounted. To add support for this we need to enable
the micrell phy driver in the config.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable EXT4_FS to have rootfs in EXT[2-4].
Other changes are result of savedefconfig keeping minimal config (even
without enabling EXT4_FS, these would be present).
Signed-off-by: afzal mohammed <afzal.mohd.ma@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Commit 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi") causes boot
issues when the bootloader does not create a 'chosen' node if such node
is not present in the dtb.
The reason for the boot failure is well explained by Javier Martinez
Canillas: "the decompressor relies on a pre-existing chosen node to be
available to insert the command line and merge other ATAGS info."
, so pass an empty 'chosen' node to fix the boot problem.
This issue has been seen in the kernelci reports with Barebox as
bootloader.
Also pass the 'memory' node in order to fix boot issues on the SolidRun
iMX6 platforms.
Fixes: 7f107887d1 ("ARM: dts: imx: Remove skeleton.dtsi")
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRA72 and DRA718 EVM boards has a pcf8575 gpio expander
which is used for the LCD/LEDs and USB vbus detection.
Add the node for the pcf8575.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add skeleton pdata-quirks for davinci.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
[nsekhar@ti.com: move changes to build pdata-quirks.c and call
to pdata_quirks_init() to this patch]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The GNU assembler for ARM version 2.22 or older fails to infer the
element size from the vmov instructions, and aborts the build in
the following way;
.../aes-neonbs-core.S: Assembler messages:
.../aes-neonbs-core.S:817: Error: bad type for scalar -- `vmov q1h[1],r10'
.../aes-neonbs-core.S:817: Error: bad type for scalar -- `vmov q1h[0],r9'
.../aes-neonbs-core.S:817: Error: bad type for scalar -- `vmov q1l[1],r8'
.../aes-neonbs-core.S:817: Error: bad type for scalar -- `vmov q1l[0],r7'
.../aes-neonbs-core.S:818: Error: bad type for scalar -- `vmov q2h[1],r10'
.../aes-neonbs-core.S:818: Error: bad type for scalar -- `vmov q2h[0],r9'
.../aes-neonbs-core.S:818: Error: bad type for scalar -- `vmov q2l[1],r8'
.../aes-neonbs-core.S:818: Error: bad type for scalar -- `vmov q2l[0],r7'
Fix this by setting the element size explicitly, by replacing vmov with
vmov.32.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Now that we have a driver for the GR8, we can convert our DT to it.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have drivers for all of them, convert all the SoCs that share
the sun5i DTSI to the new CCU driver.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
GPIO4_11 is on pin 152(MX6DL_PAD_KEY_ROW2) and not on pin
151(MX6DL_PAD_KEY_ROW1).
I found the error while booting a mainline kernel on APF6S SoM and
noticed the following message:
[ 2.609337] imx6dl-pinctrl 20e0000.iomuxc: pin MX6DL_PAD_KEY_ROW1
already requested by 20a8000.gpio:105; cannot claim for 20a8000.gpio:107
[ 2.621884] imx6dl-pinctrl 20e0000.iomuxc: pin-151 (20a8000.gpio:107)
status -22
[ 2.629303] spi_imx 2008000.ecspi: Can't get CS GPIO 107
With this patch, the message is gone and spi_imx driver probes correctly.
Fixes: bb728d662b ("ARM: dts: add gpio-ranges property to iMX GPIO controllers")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Link the ARM GIC to the INTC-SYS module clock, and add it to the SYSC
"always-on" PM Domain, so it can be power managed using that clock.
Note that currently the GIC-400 driver doesn't support module clocks nor
Runtime PM, so this must be handled as a critical clock.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fixed code indent tabs in respective imx6qdl dtsi files and
also add space on imx6qdl-icore-rqs.dtsi on usdhc bus-width nodes.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The ZII Dev Rev C board has EEPROMs hanging the 88E6390 Ethernet switch
chips. Add an "eeprom-length" property to allow access from ethtool.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
A bugfix added a new local variable that is only used inside of an #ifdef
section, and unused if CONFIG_PERF_EVENTS is disabled:
arch/arm/mach-imx/mmdc.c:63:25: warning: 'cpuhp_mmdc_state' defined but not used [-Wunused-variable]
This moves the variable down inside that same ifdef.
Fixes: a051f220d6 ("ARM/imx/mmcd: Fix broken cpu hotplug handling")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Frank Li <Frank.Li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Apart from the already enabled Designware HDMI port, the Utilite Pro
has a second display pipeline which has the following shape:
IPU1 DI0 --> Parallel display --> tfp410 rgb24 to DVI encoder
--> HDMI connector.
Enable support for it.
In addition, since this pipeline is hardwired to IPU1, sever the link
between IPU1 and the SoC-internal Designware HDMI encoder forcing the
latter to be connected to IPU2 instead of IPU1. Otherwise, it is not
possible to drive both displays at high resolution due to the bandwidth
limitations of a single IPU.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Enable DMA on uart1 to get a more reliable console.
Cc: stable <stable@vger.kernel.org> #v4.3+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Pro4 SoC has 2 slots of SD controllers, so 2 pin-mux nodes
(SD and SD1) are needed. The other SoCs have only 1 SD slot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be patched
-----BEGIN PGP SIGNATURE-----
iQEcBAABCAAGBQJYglwIAAoJEED/6hsPKofoZp0H+gLLEeKP0Mu+olXiOWjB/KFp
WBDAR1872xIjvEcOl9l6AZgdmp2hk7KW1t+kJj5npgu237v6fHBO9ybqrAfhfU4l
PH23zOebL15HINcwCK6OcxOTiOtgae5Nui1cnLJBHDQgPTC/VmIE8NgV/qrMyo2r
Vth+K/cBLKiWG9JhyQvxmrfupNJUknLSH7CTnlO/fC8GEJzDfMpUl7B1Ui0TGK53
ExVgVLg3F28SErj9bUU8y4VJhMrwDAf2Kx2BNHqDbzXMzTdp0LrGRymFLl2/Gxez
zLtZDfGYYzEhPp1NuDydlxLb8ymnsQNB7K6Kau0w9JoAvOYwfUYfDt+GaTegwYM=
=dPtS
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM fixes from Radim Krčmář:
"ARM:
- Fix for timer setup on VHE machines
- Drop spurious warning when the timer races against the vcpu running
again
- Prevent a vgic deadlock when the initialization fails (for stable)
s390:
- Fix a kernel memory exposure (for stable)
x86:
- Fix exception injection when hypercall instruction cannot be
patched"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: s390: do not expose random data via facility bitmap
KVM: x86: fix fixing of hypercalls
KVM: arm/arm64: vgic: Fix deadlock on error handling
KVM: arm64: Access CNTHCTL_EL2 bit fields correctly on VHE systems
KVM: arm/arm64: Fix occasional warning from the timer work function
Allwinner V3s is a low-end single-core Cortex-A7 SoC, with 64MB
integrated DRAM, and several peripherals.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Hwmod core tries to reset and idles each IP that is registered with hwmod.
In case of earlycon, that specific uart IP cannot be reset or keep it in
idle state else earlycon hangs once hwmod resets that uart IP. So add support
to not reset uart that is being used as earlycon only if CONFIG_SERIAL_EARLYCON
is enabled.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add stdout-path property in /chosen node so that earlycon can be
used by just adding earlycon in bootargs.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the ISL29023 ALS connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the 16-Bit I/O Expander connected via the I2C bus.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the BQ32000 Real Time Clock connected to the I2C bus
and disable the AM335x Real Time Clock.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the 32Mb Serial Flash Memory connected to SPI0
and using CS1.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The UART1 is connected to the infrared (IR) receiver module, so enable it
to be able to comunicate with it.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
I2C1 is not used so remove it in order to avoid conflicts.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP36/37 families are similar, but there are a few features sections
that can help identify some of them. Let's add checks for 3630/3730,
OMAP3621, DM3725, OMAP3615/DM3715, OMAP3611, and AM3703 all based on
features similar to what was done for the OMAP34xx/35xx series
The checkpatch flags some warnings for braces, but I kept the coding style
to match the adjacent code for consistency.
I don't have an OMAP36xx to test, but this was tested on both a DM3730 and
AM3703.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the commit ca43ea345d ("ARM: OMAP2+: hwmod: Add a new
flag to handle SIDLE in SWSUP only in active"), UART IP needs the sidle
mode to be controlled in SW only while they are active. Once inactive,
the IP needs to be put back in HW control so they are also wakeup
capable. The flag HWMOD_SWSUP_SIDLE takes care of this. So add this flag
to all instances of UART.
With this change, 8250 UART now gives out proper RX Timeout interrupts
and is usable as console.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since the hip01 doesn't support cpu hotplug now, and doesn't implement
the hip01_cpu_die function, drop the declaration.
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
This patch enables RTC on stm32f429-disco with LSI as clock source because
X2 crystal for LSE is not fitted by default.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch set HSE_RTC clock frequency to 1 MHz, as the clock supplied to
the RTC must be 1 MHz.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch include auxiliary clock definition (clocks which are not derived
from system clock.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds an external I2S clock in the DT.
The I2S clock could be derived from an external I2S clock or by I2S pll.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Enable analog to digital converter on stm32f429i-eval board.
It has on-board potentimeter wired to ADC3 in8 analog pin and
uses fixed regulator to provide reference voltage.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch adds USART3 pin configuration on PB10/PA11 pins
for STM32F469I-DISCO board.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This patch fix memory size to support 16MB of external SDRAM.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
This enables the iio subsystem. This will be used by LEGO MINDSTORMS EV3,
which has an ADS7957 chip.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
This adds a device tree definition file for LEGO MINDSTORMS EV3.
What is working:
* Pin muxing
* Pinconf
* GPIOs
* MicroSD card reader
* UART on input port 1
* Buttons
* LEDs
* Poweroff/reset
* Flash memory
* EEPROM
* USB host port
* USB peripheral port
What is not working/to be added later:
* Speaker - have patch submitted to get pwm-beeper working - maybe someday
it will have a real sound driver that uses PRU
* A/DC chip - have driver submitted and accepted - waiting for ack on
device tree bindings
* Display - waiting for "simple DRM" to be mainlined
* Bluetooth - needs new driver for sequencing power/enable/clock
* Input and output ports - need some sort of new phy or extcon driver as
well as PRU UART and PRU I2C drivers
* Battery indication - needs new power supply driver
Note on flash partitions:
These partitions are based on the official EV3 firmware from LEGO. It is
expected that most users of the mainline kernel on EV3 will be booting from
an SD card while retaining the official firmware in the flash memory.
Furthermore, the official firmware uses an ancient U-Boot (2009) that has
no device tree support. So, it makes sense to have this partition table in
the EV3 device tree file. In the unlikely case that anyone does create
their own firmware image with different partitioning, they can use a modern
U-Boot in their own firmware image that modifies the device tree with the
custom partitions.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
We've been sitting on fixes for a while, and they keep trickling in at a low
rate. Nothing in here comes across as particularly scary or noteworthy, for
the most part it's a large collection of small DT tweaks.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cc1U
-----END PGP SIGNATURE-----
Merge tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on fixes for a while, and they keep trickling in at
a low rate. Nothing in here comes across as particularly scary or
noteworthy, for the most part it's a large collection of small DT
tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
ARM: dts: da850-evm: fix read access to SPI flash
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: NSP: Fix DT ranges error
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
...
please pull the following changes:
- Rafal enables the UART by default on all BCM5301x, BCM4708, BCM4709 since
every device found out there has it enabled by default. He also fixes the
LED definitions for the Luxul XWR-3100 device, enables USB controllers and
their respective PHY devices, specifies the correct GPIO to power on USB
HUBs, adds the additional RAM bank for somes devices, and finally sets the
correct 5Ghz frequency limits on the Netgear R8000
- Jon does a number of Norsthar Plus SoC cleanups, fixes NAND partitions unit
addresses, adds QSPI support to a bunch of boards, adds Ethernet switch ports
to the BCM958625K reference board, enables 3rd Ethernet MAC instance to
relevant DTSes, enables Ethernet on the XMC board, and finally adds SD/MMC
support to the XMC board
- Boris adds the Video Encoder nodes to the Raspberry Pi DTS include files
ands enables it on the relevant boards
- Dan adds support for two new Luxul devices: XAP-1410 and XWR-1200, both
BCM47081 based SoCs
-----BEGIN PGP SIGNATURE-----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=wFmP
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.11/devicetree' of http://github.com/Broadcom/stblinux into next/dt
This pull request contains Broadcom ARM-based SoC Device Tree changes for 4.11,
please pull the following changes:
- Rafal enables the UART by default on all BCM5301x, BCM4708, BCM4709 since
every device found out there has it enabled by default. He also fixes the
LED definitions for the Luxul XWR-3100 device, enables USB controllers and
their respective PHY devices, specifies the correct GPIO to power on USB
HUBs, adds the additional RAM bank for somes devices, and finally sets the
correct 5Ghz frequency limits on the Netgear R8000
- Jon does a number of Norsthar Plus SoC cleanups, fixes NAND partitions unit
addresses, adds QSPI support to a bunch of boards, adds Ethernet switch ports
to the BCM958625K reference board, enables 3rd Ethernet MAC instance to
relevant DTSes, enables Ethernet on the XMC board, and finally adds SD/MMC
support to the XMC board
- Boris adds the Video Encoder nodes to the Raspberry Pi DTS include files
ands enables it on the relevant boards
- Dan adds support for two new Luxul devices: XAP-1410 and XWR-1200, both
BCM47081 based SoCs
* tag 'arm-soc/for-4.11/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: bcm283x: Enable the VEC IP on all RaspberryPi boards
ARM: dts: bcm283x: Add VEC node in bcm283x.dtsi
ARM: dts: BCM5301X: Add DT for Luxul XWR-1200
ARM: dts: BCM5301X: Add DT for Luxul XAP-1410
ARM: dts: BCM5301X: Set 5 GHz wireless frequency limits on Netgear R8000
ARM: dts: NSP: Add SD/MMC support
ARM: dts: NSP: Add Ethernet to NSP XMC
ARM: dts: NSP: Add and enable amac2
ARM: dts: NSP: Add BCM958625K switch ports
ARM: dts: NSP: Add QSPI support to missing boards
ARM: dts: NSP: Correct NAND partition unit address
ARM: dts: NSP: DT Clean-ups
ARM: dts: BCM53573: Specify USB ports of on-SoC controllers
ARM: dts: BCM5301X: Specify all RAM by including an extra block
ARM: dts: BCM5301X: Set GPIO enabling USB power on Netgear R7000
ARM: dts: BCM5301X: Specify USB controllers in DT
ARM: dts: BCM5301X: Fix LAN LED labels for Luxul XWR-3100
ARM: dts: BCM5301X: Enable UART by default for BCM4708(1), BCM4709(4) & BCM53012
Signed-off-by: Olof Johansson <olof@lixom.net>
Read access to the SPI flash are broken on da850-evm, i.e. the data
read is not what is actually programmed on the flash.
According to the datasheet for the M25P64 part present on the da850-evm,
if the SPI frequency is higher than 20MHz then the READ command is not
usable anymore and only the FAST_READ command can be used to read data.
This commit specifies in the DTS that we should use FAST_READ command
instead of the READ command.
Cc: stable@vger.kernel.org
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[nsekhar@ti.com: subject line adjustment]
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net:
dsa: Document new binding"). The legacy binding node is kept included, but is
marked disabled.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Utilize the new DSA binding, introduced with commit 8c5ad1d617 ("net: dsa:
Document new binding"). The legacy binding node is kept included, but is marked
disabled.
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Enable DMA on usart3 to get a more reliable console. This is especially
useful for automation and kernelci were a kernel with PROVE_LOCKING enabled
is quite susceptible to character loss, resulting in tests failure.
Cc: stable <stable@vger.kernel.org> #v4.1+
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2E SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2L SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module contains specific
memory-mapped registers that can be used to perform reset
management using specific bits for the DSPs available on the
SoC. The PSC is defined using a syscon node, and the reset
functionality is defined using a child syscon reset controller
node.
Add this syscon reset controller node as well as the reset
control data for the resets it supports for the 66AK2H SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Power Sleep Controller (PSC) module is responsible
for the power and clock management for each of the peripherals
present on the SoC. Represent this as a syscon node so that
multiple users can leverage it for various functionalities.
Signed-off-by: Suman Anna <s-anna@ti.com>
[afd@ti.com: add simple-mfd compatible]
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The Keystone 2 family of SoCs will use various Reset Controller
drivers for managing the resets of remote processor devices like
DSPs on the SoC, so select the ARCH_HAS_RESET_CONTROLLER option
by default to enable the Reset framework.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Fix the pa clock to point to the clkpa which has clock rate of 1/3 of PA
PLL clock and add clock names.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
