Removing qoriq-sec4.1-0.dtsi as it is not used by any soc anymore.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add dts file for ac14xx board and its board compatible
string to the generic mpc512x board match list.
Also add phandle to the dma DT node since there is a change
(for MPC5121 SDHC DMA support) merged via linux-mmc tree
with reference to the dma controller node in the sdhc node.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
B4860QDS and B4420QDS share same QDS board
* common board features have been added in b4qds.dts
* various board differences are in respective files of B4860 and B4420
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
B4860 and B4420 are similar that share some commonalities
* common features have been added in b4si-pre.dtsi and b4si-post.dtsi
* differences are added in respective silicon files of B4860 and B4420
There are several things missing from the device trees of B4860 and B4420:
* DPAA related nodes (Qman, Bman, Fman, Rman)
* DSP related nodes/information
* serdes, sfp(security fuse processor), thermal,
gpio, maple, cpri, quad timers nodes
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Fix cpu unit address to match reg
* Update compatible for rcpm & clockgen to be 2.0 instead of 2
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
As the T4240 is based on corenet chassis v2.0 spec we update the global
utilities (GUTS) device config compatiable to reflect this.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Identifies the epu as compatible with Chassis v1 Debug IP.
Signed-off-by: Stephen George <Stephen.George@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to the partition of JFFS2 overlaps with QE ucode firmware, So JFFS2
will break QE ucode. Shrink JFFS2's partition to reserve the space of
QE ucode firmware.
Signed-off-by: Jiucheng Xu <Jiucheng.Xu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add first usb controller node for qonverge qoriq platforms like
B4860, etc
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable a baseline T4240 SoC to boot. There are several things missing
from the device trees for T4240:
* Proper PAMU topology information
* DPAA related nodes (Qman, Bman, Fman, Rman, DCE)
* Prefetch Manager
* Thermal monitor unit
* Interlaken
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree for SEC (crypto engine) version 5.0 used on T4240.
Signed-off-by: Vakul Garg <vakul@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
-also define a binding for fsl,eref-* properties
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
<<
Please pull mpc5xxx patches for v3.9. The bestcomm driver is
moved to drivers/dma (so it will be usable for ColdFire).
mpc5121 now provides common dtsi file and existing mpc5121 device
trees use it. There are some minor clock init and sparse fixes
and updates for various 5200 device tree files from Grant. Some
fixes for bugs in the mpc5121 DIU driver are also included here
(Andrew Morton suggested to push them via my mpc5xxx tree).
>>
BSC9131RDB doesn't have SDHC enabled. As a result of this typo,
the node was not getting disabled from the device tree which was
leading to linux hang during bootup
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the Prodrive PPA8548 AMC module. Board
is an MPC8548 AMC platform used in RapidIO systems. This module is
also used to test/work on mainline linux RapidIO software.
PPA8548 overview:
- 1.3 GHz Freescale PowerQUICC III MPC8548 processor
- 1 GB DDR2 @ 266 MHz
- 8 MB NOR flash
- Serial RapidIO 1.2
- 1 x 10/100/1000 BASE-T front ethernet
- 1 x 1000 BASE-BX ethernet on AMC connector
Signed-off-by: Stef van Os <stef.van.os@prodrive.nl>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This facilitates getting the physical address of the SEC node.
Signed-off-by: Liu po <po.liu@freescale.com>
Reviewed-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix and/or improve the compatible strings of the PCI device tree nodes for
some Freescale SOCs. This fixes some issues and improves consistency among
the SOCs.
Specifically:
1) The P1022 has a v1 PCIe controller, so the compatible property should just
say "fsl,mpc8548-pcie". U-Boot does not look for "fsl,p1022-pcie", so it
wasn't fixing up the node.
2) The P4080 has a v2.1 PCIe controller, so add that version-specific string
to the device tree. Update the kernel to also look for that string.
Currently, the kernel looks for "fsl,p4080-pcie" specifically, but
eventually that check should be deleted.
3) The P1010 device tree claims compatibility with v2.2 and v2.3, but that's
redundant. No other device tree does this. Remove the v2.2 string.
4) The kernel looks for both "fsl,p1023-pcie" and "fsl,qoriq-pcie-v2.2",
even though the P1023 device trees has always included both strings. Remove
the search for "fsl,p1023-pcie".
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PAMU caches use the LIODNs to determine which cache lines hold the
entries for the corresponding LIODs. The LIODNs must therefore be
carefully assigned to avoid cache thrashing -- two active LIODs with
LIODNs that put them in the same cache line.
Currently, LIODNs are statically assigned by U-Boot, but this has
limitations. LIODNs are assigned even for devices that may be disabled
or unused by the kernel. Static assignments also do not allow for device
drivers which may know which LIODs can be used simultaneously. In
other words, we really should assign LIODNs dynamically in Linux.
To do that, we need to describe the PAMU device and cache topologies in
the device trees.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By moving the two JP12 jumpers 90 degrees, and switching the
setting of SW2.8, the sbc8548 can be configured to boot off
the alternate 64MB SODIMM, which when populated with u-boot
can be a handy recovery option, in case the u-boot in the
8MB soldered on flash gets corrupted. Here we add an alternate
dts file to match that configuration.
To better highlight the differences, the output from the u-boot
"fli" command is shown for the normal configuration and then
the alternate configuration.
Normal:
-----------------------
Bank # 1: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FF800000 E FF820000 E FF840000 E FF860000 E FF880000 E
[...]
FFEE0000 E FFF00000 E FFF20000 E FFF40000 E FFF60000 E
FFF80000 FFFA0000 RO FFFC0000 RO FFFE0000 RO
Bank # 2: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EC000000 E EC080000 E EC100000 E EC180000 E EC200000 E
[...]
EFC00000 E EFC80000 E EFD00000 E EFD80000 E EFE00000 E
EFE80000 E EFF00000 EFF80000
-----------------------
Alternate:
-----------------------
Bank # 1: CFI conformant flash (32 x 8) Size: 64 MB in 128 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x18
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
FC000000 E FC080000 E FC100000 E FC180000 E FC200000 E
[...]
FFC00000 E FFC80000 E FFD00000 E FFD80000 E FFE00000 E
FFE80000 E FFF00000 RO FFF80000 RO
Bank # 2: CFI conformant flash (8 x 8) Size: 8 MB in 64 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x17
Erase timeout: 4096 ms, write timeout: 1 ms
Buffer write timeout: 2 ms, buffer size: 32 bytes
Sector Start Addresses:
EF800000 E EF820000 E EF840000 E EF860000 E EF880000 E
[...]
EFEE0000 E EFF00000 E EFF20000 E EFF40000 E EFF60000 E
EFF80000 E EFFA0000 EFFC0000 EFFE0000
-----------------------
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The original memory map for the sbc8548 had the 64MB SODIMM flash
device misaligned by 8MB to allow a window of address space for
the soldered on 8MB device -- i.e.
start end CS<n> width Desc.
----------------------------------------------------------
fb80_0000 ff7f_ffff CS6 32 SODIMM flash (64MB)
ff80_0000 ffff_ffff CS0 8 Boot flash (8MB)
However, if we want to change the configuration so that it boots
off the 64MB flash, it is in turn then aligned with a 64MB boundary,
starting at fc00_0000 (and the 8MB @ fb80_0000 -> fbff_ffff).
This makes for complicated updates, since what is the beginning
of the physical device is 8MB into its address space in the default
configuration shown above.
This issue was fixed as of u-boot commit 3fd673cf363bc86ed42eff713d4
("sbc8548: relocate 64MB user flash to sane boundary") -- in which
the SODIMM was mapped to ec00_0000 (natively aligned under efff_ffff)
and so when JP12/SW2.8 are switched, it will be a a simple 0xec --> 0xfc
mapping between the two instances.
Here we make the associated changes in the localbus flash memory
map in the dts file: indicating the 64MB device starts at ec00_0000
and that the tail end of the 64MB device (last 2 sectors) can contain
a bootloader image.
The partitions for both flash devices get a clean-up; there were
non-meaningful assignments in there that probably originated from
the MPC8548CDS on which the file was based on. Now there is just
the categorization of free space and bootloader images.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updates to u-boot allow this board to boot off of either
the 8MB soldered on flash, or the 64MB SODIMM flash.
This is achieved by changing JP12 and SW2.8 which in turn
swaps which flash device appears on /CS0 and /CS6 respectively.
Since the flash devices are not the same size, this also
changes the MTD memory map layout on the local bus.
Here we split the common chunks out into a pre and post
include, so they can be reused by an upcoming "alternative
boot" dts file; leaving only the local bus chunk behind.
No content changes are made at this point - it is just purely
the move to using include files.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DTC labels feature allows a dts file to reference a node without
having to reproduce the entire node hierarchy above it. We can use this
to simplify the MPC5200 board dts files by referencing the gpt nodes by
label.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
[agust: fixed gpt7 phandle in the csi node of o2d.dtsi]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The Lite5200 evaluation board has a number of debug LEDs that Linux
doesn't know about yet. This change adds a gpio-leds stanza to the
lite5200 device tree so that the correct driver can get hooked up.
Also, make use of the dtc labels feature to reduce the number of source
lines required to add the gpio-controller property to the general
purpose timer nodes. In addition, the required #gpio-cells properties
are added to the common mpc5200b dtsi include file so that each board
doesn't need to add them explicitly. This still doesn't enable gpio
mode, 'gpio-controller' is required for that, but it means less work
needs to be done by board ports.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the marvel phy which is present on the ml507 board.
Without this ethtool causes kernel-oopses.
Tested on ml507 board.
Signed-off-by: Gernot Vormayr <gvormayr@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch consists of:
- Add driver for OCM component
- Export OCM Information at /sys/kernel/debug/ppc4xx_ocm/info
Signed-off-by: Vinh Nguyen Huu Tuong <vhtnguyen@apm.com>
Acked-by: Josh Boyer <jwboyer@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds the MPC5200B based a3m071 board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The RaidEngine is a new Freescale hardware that used for parity
computation offloading in RAID5/6.
This patch adds the device node in device tree and related binding
documentation.
Signed-off-by: Harninder Rai <harninder.rai@freescale.com>
Signed-off-by: Naveen Burmi <naveenburmi@freescale.com>
Signed-off-by: Xuelin Shi <b29237@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a node for the pcm030-audio-fabric ASoC driver
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Pull powerpc updates from Benjamin Herrenschmidt:
"Some highlights in addition to the usual batch of fixes:
- 64TB address space support for 64-bit processes by Aneesh Kumar
- Gavin Shan did a major cleanup & re-organization of our EEH support
code (IBM fancy PCI error handling & recovery infrastructure) which
paves the way for supporting different platform backends, along
with some rework of the PCIe code for the PowerNV platform in order
to remove home made resource allocations and instead use the
generic code (which is possible after some small improvements to it
done by Gavin).
- Uprobes support by Ananth N Mavinakayanahalli
- A pile of embedded updates from Freescale folks, including new SoC
and board supports, more KVM stuff including preparing for 64-bit
BookE KVM support, ePAPR 1.1 updates, etc..."
Fixup trivial conflicts in drivers/scsi/ipr.c
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (146 commits)
powerpc/iommu: Fix multiple issues with IOMMU pools code
powerpc: Fix VMX fix for memcpy case
driver/mtd:IFC NAND:Initialise internal SRAM before any write
powerpc/fsl-pci: use 'Header Type' to identify PCIE mode
powerpc/eeh: Don't release eeh_mutex in eeh_phb_pe_get
powerpc: Remove tlb batching hack for nighthawk
powerpc: Set paca->data_offset = 0 for boot cpu
powerpc/perf: Sample only if SIAR-Valid bit is set in P7+
powerpc/fsl-pci: fix warning when CONFIG_SWIOTLB is disabled
powerpc/mpc85xx: Update interrupt handling for IFC controller
powerpc/85xx: Enable USB support in p1023rds_defconfig
powerpc/smp: Do not disable IPI interrupts during suspend
powerpc/eeh: Fix crash on converting OF node to edev
powerpc/eeh: Lock module while handling EEH event
powerpc/kprobe: Don't emulate store when kprobe stwu r1
powerpc/kprobe: Complete kprobe and migrate exception frame
powerpc/kprobe: Introduce a new thread flag
powerpc: Remove unused __get_user64() and __put_user64()
powerpc/eeh: Global mutex to protect PE tree
powerpc/eeh: Remove EEH PE for normal PCI hotplug
...
Pull the trivial tree from Jiri Kosina:
"Tiny usual fixes all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
doc: fix old config name of kprobetrace
fs/fs-writeback.c: cleanup riteback_sb_inodes kerneldoc
btrfs: fix the commment for the action flags in delayed-ref.h
btrfs: fix trivial typo for the comment of BTRFS_FREE_INO_OBJECTID
vfs: fix kerneldoc for generic_fh_to_parent()
treewide: fix comment/printk/variable typos
ipr: fix small coding style issues
doc: fix broken utf8 encoding
nfs: comment fix
platform/x86: fix asus_laptop.wled_type module parameter
mfd: printk/comment fixes
doc: getdelays.c: remember to close() socket on error in create_nl_socket()
doc: aliasing-test: close fd on write error
mmc: fix comment typos
dma: fix comments
spi: fix comment/printk typos in spi
Coccinelle: fix typo in memdup_user.cocci
tmiofb: missing NULL pointer checks
tools: perf: Fix typo in tools/perf
tools/testing: fix comment / output typos
...
Add common o2d dtsi file to reuse it for other configurations.
Add machine compatible string to mpc5200 simple platform file.
Add dts files for O2D, O2I, O2MNT, O2DNT2, O2D300 and O3DNT boards.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Device node adt7461 was wrongly added in p5040ds.dts, it should be added
into i2c instead of localbus, when build p5040ds.dtb, a warning will dump:
Warning (reg_format): "reg" property in
/localbus@ffe124000/nand@2,0/adt7461@4c has invalid length (4 bytes)
(#address-cells == 1, #size-cells == 1)
This was introduced by:
commit ea6b1ba692bcb5f6e39f409a78cf8b04fdf23baa
Author: Jia Hongtao <B38951@freescale.com>
Date: Tue Aug 28 10:00:55 2012 +0800
powerpc: add adt7461 thermal monitor support to applicable boards
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
create partition table for norflash.
Signed-off-by: Wang Dongsheng <Dongsheng.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add thermal monitor support to following boards:
P1022DS, MPC8536DS, P2041RDB, P3041DS, P4080DS, P5020DS, P5040DS
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
This patch update all the e5500 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all the e500mc platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
power-isa-version and power-isa-* are cpu node general properties defined
in ePAPR.
If the power-isa-version property exists, then for each category from the
Categories section of Book I of the Power ISA version indicated, the
existence of a property named power-isa-[CAT], where [CAT] is the
abbreviated category name with all uppercase letters converted to
lowercase, indicates that the category is supported by the implementation.
The patch update all e500v2 platforms.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale / iVeia P1022RDK reference board is a small-factor board
with a Freescale P1022 SOC. It includes:
1) 512 MB 64-bit DDR3-800 (max) memory
2) 8MB SPI serial flash memory for boot loader
3) Bootable 4-bit SD/MMC port
4) Two 10/100/1000 Ethernet connectors
5) One SATA port
6) Two USB ports
7) One PCIe x4 slot
8) DVI video connector
9) Audio input and output jacks, powered by a Wolfson WM8960 codec.
Unlike the P1022DS, the P1022RDK does not have any localbus devices,
presumably because of the localbus / DIU multiplexing restriction of
the P1022 SOC.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for the Freescale P5040DS Reference Board ("Superhydra"), which
is similar to the P5020DS. Features of the P5040 are listed below, but
not all of these features (e.g. DPAA networking) are currently supported.
Four P5040 single-threaded e5500 cores built
Up to 2.4 GHz with 64-bit ISA support
Three levels of instruction: user, supervisor, hypervisor
CoreNet platform cache (CPC)
2.0 MB configures as dual 1 MB blocks hierarchical interconnect fabric
Two 64-bit DDR3/3L SDRAM memory controllers with ECC and interleaving
support Up to 1600MT/s
Memory pre-fetch engine
DPAA incorporating acceleration for the following functions
Packet parsing, classification, and distribution (FMAN)
Queue management for scheduling, packet sequencing and
congestion management (QMAN)
Hardware buffer management for buffer allocation and
de-allocation (BMAN)
Cryptography acceleration (SEC 5.0) at up to 40 Gbps SerDes
20 lanes at up to 5 Gbps
Supports SGMII, XAUI, PCIe rev1.1/2.0, SATA Ethernet interfaces
Two 10 Gbps Ethernet MACs
Ten 1 Gbps Ethernet MACs
High-speed peripheral interfaces
Two PCI Express 2.0/3.0 controllers
Additional peripheral interfaces
Two serial ATA (SATA 2.0) controllers
Two high-speed USB 2.0 controllers with integrated PHY
Enhanced secure digital host controller (SD/MMC/eMMC)
Enhanced serial peripheral interface (eSPI)
Two I2C controllers
Four UARTs
Integrated flash controller supporting NAND and NOR flash
DMA
Dual four channel
Support for hardware virtualization and partitioning enforcement
Extra privileged level for hypervisor support
QorIQ Trust Architecture 1.1
Secure boot, secure debug, tamper detection, volatile key storage
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree (dtsi) files for the Freescale P5040 SOC. Since this
SOC introduces SEC v5.2, add the dtsi file for that also.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We only need two examples of CAMP device trees in the upstream kernel.
Co-operative Asymmetric Multi-Processing (CAMP) is a technique where two
or more operating systems (typically multiple copies of the same Linux
kernel) are loaded into memory, and each kernel is given a subset of the
available cores to execute on. For example, on a four-core system, one
kernel runs on cores 0 and 1, and the other runs on cores 2 and 3.
The devices are also partitioned among the operating systems, and this is
done with customized device trees. Each kernel gets its own device tree
that has only the devices that it should know about.
Unfortunately, this approach is very hackish. The kernels are trusted to
only access devices in their respective device trees, and the partitioning
only works for devices that can be handled. Crafting the device trees is a
tricky process, and getting U-Boot to load and start all kernels is
cumbersome.
But most importantly, each CAMP setup is very application-specific, since
the actual partitioning of resources is done in the DTS by the system
designer. Therefore, it doesn't make a lot of sense to have a lot of CAMP
device trees, since we only expect them to be used as examples.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Several files in obj-plat depend on libfdt header file. Sometimes
when building one can see the following issue. This patch adds
libfdt as dependency to those object files
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:854:1: error: unterminated comment
| In file included from arch/powerpc/boot/treeboot-iss4xx.c:33:0:
| arch/powerpc/boot/libfdt.h:1:0: error: unterminated #ifndef
| BOOTCC arch/powerpc/boot/inffast.o
| make[1]: *** [arch/powerpc/boot/treeboot-iss4xx.o] Error 1
| make[1]: *** Waiting for unfinished jobs....
| BOOTCC arch/powerpc/boot/inflate.o
| make: *** [uImage] Error 2
| ERROR: oe_runmake failed
| ERROR: Function failed: do_compile (see /srv/home/pokybuild/yocto-autobuilder/yocto-slave/p1022ds/build/build/tmp/work/p1022ds-poky-linux-gnuspe/linux-qoriq-sdk-3.0.34-r5/temp/log.do_compile.2167 for further information)
NOTE: recipe linux-qoriq-sdk-3.0.34-r5: task do_compile: Failed
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 4f3865fb57 ("zlib_inflate: Upgrade
library code to a recent version") removed infblock.c, infblock.h,
infcodes.c, and infcodes.h from the tree. Remove their entries in
powerpc's .gitignore file too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Add the missing usb controller version info and port0, which is
required during setup usb phy.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Default CoreNet Coherency Bus (CCB) frequency on P3041 is 750MHz, but espi
cannot work at 40MHz with this CCB frequency, so we need to slow down the
clock rate of espi to 35MHz to make it work stable at the CCB frequency.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In SGMII riser card different PHY chip are used with different external
IRQ from eTSEC. To support PHY link state auto detect in SGMII mode we
should add another group of PHY nodes for SGMII mode.
For MPC8572DS IRQ6 is used for PHY0~PHY1, IRQ7 is used for PHY2~PHY3.
For MPC8544DS and MPC8536DS IRQ6 is used for PHY0~PHY1.
For P2020DS IRQ5 is used for PHY1~PHY2.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board is really P1021RDB-PC, so rename from p1021rdb.* to p1021rdb-pc.*
Signed-off-by: Xu Jiucheng <Jiucheng.Xu@freescale.com>
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add device tree nodes to enable ucc uart support on P1025RDB.
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With 2-cell format interrupts of MSI PCIe ethernet card can not work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 96cc017c5b.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This reverts commit 0c00f65653.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the RTC support into the p1022ds device tree
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Commit 430b01e8f5 ("[POWERPC] Kill
flatdevtree.c") killed the two files including flatdevtree_env.h. It was
apparently just an oversight to not kill that header too. Kill it now.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently we build all board files regardless of the final zImage
target. This is sub-optimal (in terms on compilation) and leads to
problems in one platform needlessly causing failures for other
platforms.
Use the Kconfig variables to selectively construct this board files to
build.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of the
samsung iommu code from a platform specific in-kernel interface to the
generic iommu subsystem.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hgkg
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc driver specific updates from Olof Johansson:
"These changes are specific to some driver that may be used by multiple
boards or socs. The most significant change in here is the move of
the samsung iommu code from a platform specific in-kernel interface to
the generic iommu subsystem."
Fix up trivial conflicts in arch/arm/mach-exynos/Kconfig
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mmc: dt: Consolidate DT bindings
iommu/exynos: Add iommu driver for EXYNOS Platforms
ARM: davinci: optimize the DMA ISR
ARM: davinci: implement DEBUG_LL port choice
ARM: tegra: Add SMMU enabler in AHB
ARM: tegra: Add Tegra AHB driver
Input: pxa27x_keypad add choice to set direct_key_mask
Input: pxa27x_keypad direct key may be low active
Input: pxa27x_keypad bug fix for direct_key_mask
Input: pxa27x_keypad keep clock on as wakeup source
ARM: dt: tegra: pinmux changes for USB ULPI
ARM: tegra: add USB ULPI PHY reset GPIO to device tree
ARM: tegra: don't hard-code USB ULPI PHY reset_gpio
ARM: tegra: change pll_p_out4's rate to 24MHz
ARM: tegra: fix pclk rate
ARM: tegra: reparent sclk to pll_c_out1
ARM: tegra: Add pllc clock init table
ARM: dt: tegra cardhu: basic audio support
ARM: dt: tegra30.dtsi: Add audio-related nodes
ARM: tegra: add AUXDATA required for audio
...
* drivers/mmc:
mmc: dt: Consolidate DT bindings
Also pulls in the omap/dt-missed-3.4 branch as a dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch unifies the current DT MMC bindings documentation and code,
adds generic MMC DT bindings documentation, and updates .dts files for
consistency.
[cjb: typo fixes, addition of max-frequency property]
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The association in the decice tree between PCI and MSI
using fsl,msi property was an artificial one and it does
not reflect the actual hardware.
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
Commit c55aef0e5b "powerpc/boot: Change the load address for the wrapper
to fit the kernel" adjusted the laod address if the uncompressed kernel
was too large. Ps3 does not compress the kernel and uses a different
linker script, so do not adjust the load address in that case.
fixes this build error:
powerpc64-linux-ld: section .text loaded at [0000000000e00000,0000000000e0721b] overlaps section .kernel:dtb loaded at [0000000000e00000,0000000000e0066f]
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add DTS file for a4m072 board and add its name to the list
of the supported boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Grant Likely <grant.likely@secretlab.ca>
cc: devicetree-discuss@ozlabs.org
cc: Wolfgang Denk <wd@denx.de>
cc: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The MSIIR register for each MSI bank is aliased to a different
address. The MSI node reg property was updated to contain this
address:
e.g. reg = <0x41600 0x200 0x44140 4>;
The first region contains the address and length of the MSI
register set and the second region contains the address of
the aliased MSIIR register at 0x44140.
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create mpc8548cds_36b.dts. Support 36-bit mode.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Create mpc8548cds.dtsi
* Move lbc, soc and pci0 nodes to mpc8548cds_32b.dtsi
* Change cuImage.mpc8548cds to cuImage.mpc8548cds_32b
* Rename mpc8548cds.dts to mpc8548cds_32b.dts
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove FPGA(CADMUS) macros in code. Move it to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct ethernet1 and add ethernet2 and ethernet3.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable RapidIO and add rapidio and rmu nodes to dts.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix the compatible string of sec 4.0 to match with CAAM driver according
to Documentation/devicetree/bindings/crypto/fsl-sec4.txt
Signed-off-by: Liu Shuo <shuo.liu@freescale.com>
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mpc836x_mds platform has been broken since the commit
6fe3264945
"netdev/phy: Use mdiobus_read() so that proper locks are taken"
which caused the fsl_pq_mdio TBI autoprobe to oops. The oops
was "fixed" in commit 28d8ea2d56
"fsl_pq_mdio: Clean up tbi address configuration"
by simply removing the the autoscan code, and making tbi nodes
mandatory. Some of the newer reference platforms were updated
to have tbi nodes in 220669495b
"powerpc: Add TBI PHY node to first MDIO bus"
but the older mpc836x didn't get one and hence was just failing
with -EBUSY as follows:
fsl-pq_mdio: probe of e0102120.mdio failed with error -16
...
net eth0: Could not attach to PHY
eth0: Cannot initialize PHY, aborting.
Add a TBI node and use the 1st free address for it.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020RDB-PC Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
10 16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using VitesseTM VSC7385 L2 switch
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
Therefore, if the DIU is going to be enabled, then memory-mapped devices on
the localbus, like NOR flash, need to be disabled.
This also means that the localbus is not a 'simple-bus' any more, so remove
that string from the compatible node.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Create a 32-bit address space version of p1022ds.dts. To avoid confusion,
p1022ds.dts is renamed to p1022ds_36b.dts. We also create p1022ds.dtsi
to store some common nodes.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The properties indicates that the hardware supports waking up via magic
packet.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix typo introduced by "powerpc: Add TBI PHY node to first MDIO bus"
from Andy Fleming.
It's device_type rather than device-type, which causes the mdio probe to
fail thus making all gianfar ethernet interfaces unusable.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This is here most likely since the FSL bsp. Back in the FSL bsp it was
set to 50Mhz and working. However the driver divided the SoC freq. only
by 2. According to the TRM the platform clock (which the manual refers
in its formula) is the system clock divided by two. So in the end it has
to divide by 4 and this is what the fsl-spi driver in tree is doing.
Since then the flash is not wokring I guess. After chaning the freq from
50Mhz to 40Mhz like others do then I can access the flash.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is not at 0xffa00000. According to current u-boot source the NAND
controller is always at 0xff800000 and it is either at CS0 or CS1
depending on NAND or NAND+NOR mode. In 36bit mode it is shifted to
0xfff800000 but it has always an eight there and never an A.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1025RDB Overview
------------------
1Gbyte DDR3 SDRAM
32 Mbyte NAND flash
16Mbyte NOR flash
16 Mbyte SPI flash
SD connector to interface with the SD memory card
Real-time clock on I2C bus
PCIe:
- x1 PCIe slot
- x1 mini-PCIe slot
10/100/1000 BaseT Ethernet ports:
- eTSEC1, RGMII: one 10/100/1000 port using AtherosTM AR8021
- eTSEC2, SGMII: one 10/100/1000 port using VitesseTM VSC8221
- eTSEC3, RGMII: one 10/100/1000 port using AtherosTM AR8021
USB 2.0 port:
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
Dual RJ45 UART ports:
- DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Zhicheng Fan <b32736@freescale.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add usb controller version info for the following:
MPC8536, P1010, P1020, P1021, P1022, P1023, P2020, P2041,
P3041, P3060, P5020
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021RDB-PC Overview
-----------------
1Gbyte DDR3 (on board DDR)
16Mbyte NOR flash
32Mbyte eSLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
Real-time clock on I2C bus
SD/MMC connector to interface with the SD memory card
PCIex
- x1 PCIe slot or x1 PCIe to dual SATA controller
- x1 mini-PCIe slot
USB 2.0
- ULPI PHY interface: SMSC USB3300 USB PHY and Genesys Logic’s GL850A
- Two USB2.0 Type A receptacles
- One USB2.0 signal to Mini PCIe slot
eTSEC1: Connected to RGMII PHY VSC7385
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY AR8021
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Xu Jiucheng <B37781@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This compatible value will be used to distinguish some special features of APM821XX EMAC: no half duplex mode support, configuring jumbo frame.
Signed-off-by: Duc Dang <dhdang@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FreeScale PowerQUICC-III-compatible (mpc85xx/mpc86xx) MPICs do not
correctly report the number of hardware interrupt sources, so software
needs to override the detected value with "256".
To avoid needing to write custom board-specific code to detect that
scenario, allow it to be easily overridden in the device-tree.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale MPIC (and perhaps others in the future) is incapable of
routing non-IPI interrupts to more than once CPU at a time. Currently
all of the Freescale boards msut pass the MPIC_SINGLE_DEST_CPU flag to
mpic_alloc(), but that information should really be present in the
device-tree.
Older board code can't rely on the device-tree having the property set,
but newer platforms won't need it manually specified in the code.
[BenH: Remove unrelated changes, folded in a different patch]
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The MPIC code checks for a "big-endian" property and sets the flag
MPIC_BIG_ENDIAN if one is present, although prior to the "mpic->flags"
fixup that would never have worked anways.
Unfortunately, even now that it works properly, the Freescale mpic
device-node (the "PowerQUICC-III"-compatible one) does not specify it,
so all of the board ports need to manually pass it to mpic_alloc().
Document the flag and add it to the pq3 device tree. Existing code will
still need to pass the MPIC_BIG_ENDIAN flag because their dtb may not
have this property, but new platforms shouldn't need to do so.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable USB2 controller node for P1020RDB. USB2 controller is used only
when board boots from SPI or SD as it is muxed with eLBC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
According to latest kernel, the auto-cmd12 property should be
"sdhci,auto-cmd12", and according to the SDHC binding and the workaround for
the special chip, add the chip compatible for eSDHC: "fsl,p1022-esdhc",
"fsl,mpc8536-esdhc", "fsl,p1020-esdhc", "fsl,p2020-esdhc" and
"fsl,p1010-esdhc".
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
Kbuild: Use dtc's -d (dependency) option
dtc: Implement -d option to write out a dependency file
kbuild: Fix comment in Makefile.lib
scripts/genksyms: clean lex/yacc generated files
kbuild: Correctly deal with make options which contain an "s"
This hooks dtc into Kbuild's dependency system.
Thus, for example, "make dtbs" will rebuild tegra-harmony.dtb if only
tegra20.dtsi has changed yet tegra-harmony.dts has not. The previous
lack of this feature recently caused me to have very confusing "git
bisect" results.
For ARM, it's obvious what to add to $(targets). I'm not familiar enough
with other architectures to know what to add there. Powerpc appears to
already add various .dtb files into $(targets), but the other archs may
need something added to $(targets) to work.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
[mmarek: Dropped arch/c6x part to avoid merging commits from the middle
of the merge window]
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (185 commits)
powerpc: fix compile error with 85xx/p1010rdb.c
powerpc: fix compile error with 85xx/p1023_rds.c
powerpc/fsl: add MSI support for the Freescale hypervisor
arch/powerpc/sysdev/fsl_rmu.c: introduce missing kfree
powerpc/fsl: Add support for Integrated Flash Controller
powerpc/fsl: update compatiable on fsl 16550 uart nodes
powerpc/85xx: fix PCI and localbus properties in p1022ds.dts
powerpc/85xx: re-enable ePAPR byte channel driver in corenet32_smp_defconfig
powerpc/fsl: Update defconfigs to enable some standard FSL HW features
powerpc: Add TBI PHY node to first MDIO bus
sbc834x: put full compat string in board match check
powerpc/fsl-pci: Allow 64-bit PCIe devices to DMA to any memory address
powerpc: Fix unpaired probe_hcall_entry and probe_hcall_exit
offb: Fix setting of the pseudo-palette for >8bpp
offb: Add palette hack for qemu "standard vga" framebuffer
offb: Fix bug in calculating requested vram size
powerpc/boot: Change the WARN to INFO for boot wrapper overlap message
powerpc/44x: Fix build error on currituck platform
powerpc/boot: Change the load address for the wrapper to fit the kernel
powerpc/44x: Enable CRASH_DUMP for 440x
...
Fix up a trivial conflict in arch/powerpc/include/asm/cputime.h due to
the additional sparse-checking code for cputime_t.
The Freescale serial port's are pretty much a 16550, however there are
some FSL specific bugs and features. Add a "fsl,ns16550" compatiable
string to allow code to handle those FSL specific issues.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCI ranges, localbus reg and localbus chip-select 2 range do not match
the memory map setup by bootloader.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Systems which use the fsl_pq_mdio driver need to specify an
address for TBI PHY transactions such that the address does
not conflict with any PHYs on the bus (all transactions to
that address are directed to the onboard TBI PHY). The driver
used to scan for a free address if no address was specified,
however this ran into issues when the PHY Lib was fixed so
that all MDIO transactions were protected by a mutex. As it
is, the code was meant to serve as a transitional tool until
the device trees were all updated to specify the TBI address.
The best fix for the mutex issue was to remove the scanning code,
but it turns out some of the newer SoCs have started to omit
the tbi-phy node when SGMII is not being used. As such, these
devices will now fail unless we add a tbi-phy node to the first
mdio controller.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit c55aef0e5b ("powerpc/boot: Change the load address
for the wrapper to fit the kernel") introduced a WARNING to
inform the user that the uncompressed kernel would overlap
the boot uncompressing wrapper code. Change it to an INFO.
I initially thought, this would be a 'WARNING' for the those
boards, where the link_address should be fixed, so that the
user can take actions accordingly.
Changing the same to INFO.
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The wrapper code which uncompresses the kernel in case of a 'ppc' boot
is by default loaded at 0x00400000 and the kernel will be uncompressed
to fit the location 0-0x00400000. But with dynamic relocations, the size
of the kernel may exceed 0x00400000(4M). This would cause an overlap
of the uncompressed kernel and the boot wrapper, causing a failure in
boot.
The message looks like :
zImage starting: loaded at 0x00400000 (sp: 0x0065ffb0)
Allocating 0x5ce650 bytes for kernel ...
Insufficient memory for kernel at address 0! (_start=00400000, uncompressed size=00591a20)
This patch shifts the load address of the boot wrapper code to the next
higher MB, according to the size of the uncompressed vmlinux.
With the patch, we get the following message while building the image :
WARN: Uncompressed kernel (size 0x5b0344) overlaps the address of the wrapper(0x400000)
WARN: Fixing the link_address of wrapper to (0x600000)
Signed-off-by: Suzuki K. Poulose <suzuki@in.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The upcomming currituck patches will need to do 64-bit shifts which will
fail with undefined symbol without this patch.
I looked at linking against libgcc but we can't guarantee that libgcc
was compiled with soft-float. Also Using ../lib/div64.S or
../kernel/misc_32.S, this will break the build as the .o's need to be
built with different flags for the bootwrapper vs the kernel. So for
now the easyest option is to just copy code from
arch/powerpc/kernel/misc_32.S I don't think this code changes too often ;P
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
So I've had one of these for a while and it looks like the vendor never
bothered submitting the support upstream.
This adds it using ppc40x_simple and provides a device-tree.
There are some changes to the boot wrapper because the way u-boot works
on this thing, it seems to expect a multipart image with the kernel,
initrd and dtb in it.
The USB support is missing as it needs the yet unmerged driver for
the DWC OTG part and the GPIOs may need further definition in the dts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch enables or updates support for the CC770 and AN82527
CAN controller on the TQM8548 and TQM8xx boards.
CC: devicetree-discuss@lists.ozlabs.org
CC: linuxppc-dev@ozlabs.org
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AppliedMicro APM8018X embedded processor targets embedded applications that
require low power and a small footprint. It features a PowerPC 405 processor
core built in a 65nm low-power CMOS process with a five-stage pipeline executing
up to one instruction per cycle. The family has 128-kbytes of on-chip memory,
a 128-bit local bus and on-chip DDR2 SDRAM controller with 16-bit interface.
Signed-off-by: Tanmay Inamdar <tinamdar@apm.com>
Signed-off-by: Josh Boyer <jwboyer@gmail.com>
The Freescale P1022 has a unique pin muxing "feature" where the DIU video
controller's video signals are muxed with 24 of the local bus address signals.
When the DIU is enabled, the bulk of the local bus is disabled, preventing
access to memory-mapped devices like NOR flash and the pixis FPGA.
In this situation, the pixis supports "indirect mode", which allows access
to the pixis itself by reading/writing addresses on specific local bus
chip selects. CS0 is used to select which pixis register to access, and
CS1 is used to read/write the value.
To support this, we introduce another board-control child node of the
localbus node that contains a 'reg' property for CS0 and CS1. This will
produce the correct physical addresses for CS0 and CS1.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update all dts files that support SRIO controllers to match the new
fsl,srio device tree binding.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p5020-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p4080-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3060-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Removed mpic interrupt-parent from sec nodes, just use top level
* Fixed l3-cache IRQs, we have 2 CPCs, so we should have IRQs for both
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p3041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
* Fixed some dcsr compatiable typo's from 'p43041' to 'p3041'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Adding of MPIC timer blocks
* Dropping "fsl,p2041-IP..." from compatibles for standard blocks
* Removed mpic interrupt-parent from dcsr-epu node, just use top level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 &
* etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Updated spi node to new espi binding specification
* Renamed 'sdhci' node to 'sdhc'
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Fixed wrong reg offsets for mdio nodes associated with etsec2 & etsec3
* Dropping "fsl,p2020-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1023-IP..." from compatibles for standard blocks
* Removed incorrect power/pmc node, there are no etsec on P1023
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Changed GPIO compatiable from 'fsl,mpc8572-gpio' to 'fsl,pq3-gpio' as the
'mpc8572' compatiable is to deal with a 'mpc8572' specific to an erratum
* Updated spi node to new espi binding specification
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1022-IP..." from compatibles for standard blocks
* Fixed bug in local bus range node for CS2, was maping to
0x0 0x0xffa00000 instead of 0xf 0xffa00000
* Fixed localbus reg property should have been 0xf 0xffe05000
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Tested-by: Timur Tabi <timur@freescale.com>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Added usb node for 2nd usb controller
* Dropping "fsl,p1021-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Dropping "fsl,p1020-IP..." from compatibles for standard blocks
* Fixed PCIe interrupt-maps to have proper number of cells
* Added mdio node for etsec@26000
* Added usb node for 2nd usb controller
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Dropping "fsl,p1010-IP..." from compatibles for standard blocks
* PCI interrupt map - wrong IRQs for PCI-0 controller
* SDHC interrupt sense was wrong
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors) and
moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8572 SoC template
* Dropping "fsl,mpc8572-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Renamed SDHC node from 'sdhci' to 'sdhc'
* Dropping "fsl,mpc8569-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Dropping "fsl,mpc8568-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Moved mdio nodes up one level instead of under tsec nodes
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Added MPIC / PCIe msi node
* Dropping "fsl,mpc8548-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to a standard 2 #address-cells & #size-cells at top-level
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Removed CPU properties setup by u-boot to match other .dts
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
and moved PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Updated ethernet 'model' to 'eTSEC' as that's what on MPC8544
* Dropping "fsl,mpc8544-IP..." from compatibles for standard blocks
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Utilize new split between board & SoC, and new SoC device trees split
into pre & post utilizing 'template' includes for SoC IP blocks.
Other changes include:
* Moved to specifying interrupt-parent for mpic at root
* Moved to 4-cell mpic interrupt cells to support MPIC timers
* Added localbus node, but no chipselect details at this point
* Reworked PCIe nodes to allow supportin IRQs for controller (errors)
* and moved
PCI device IRQs down to virtual bridge level
* Moved mdio nodes up one level instead of under tsec nodes
* Added GPIO controller node to MPC8536 SoC template
[ marked as MPC8572 compatiable to get errata handling that applies ]
* Added missing cache-line-size & cache-size properties missing from
L2-cache node
* Added IP level IEEE 1588 / ptp timer node
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce some common components that we can utilize to build up the
various PQ3/85xx device trees.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* set interrupt-parent at root so its not duplicate in every node
* Add mpic timers
* Move to 4-prop cells for mpic timer
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Move SoC specific details like irq mapping to SoC dtsi
* Update interrupt property to cover both error interrupt and PCIe
runtime interrupts
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If we include the p1020rdb.dts instead of p1020si.dts we greatly reduce
duplication and maintenance. We can just list which devices are
disabled for the given core and mpic protected sources.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1023 external IRQ[4:6, 11] are not pin out, but the interrupts are
utilized by the PCIe controllers. As they are not exposed as pins we
need to set them as active-high (internal to the SoC these interrupts
are pulled down).
IRQs[0:3,7:10] are pulled up on the board so we have them set as
active-low.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (106 commits)
powerpc/p3060qds: Add support for P3060QDS board
powerpc/83xx: Add shutdown request support to MCU handling on MPC8349 MITX
powerpc/85xx: Make kexec to interate over online cpus
powerpc/fsl_booke: Fix comment in head_fsl_booke.S
powerpc/85xx: issue 15 EOI after core reset for FSL CoreNet devices
powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO driver
powerpc/85xx: Add 'fsl,pq3-gpio' compatiable for GPIO driver
powerpc/86xx: Correct Gianfar support for GE boards
powerpc/cpm: Clear muram before it is in use.
drivers/virt: add ioctl for 32-bit compat on 64-bit to fsl-hv-manager
powerpc/fsl_msi: add support for "msi-address-64" property
powerpc/85xx: Setup secondary cores PIR with hard SMP id
powerpc/fsl-booke: Fix settlbcam for 64-bit
powerpc/85xx: Adding DCSR node to dtsi device trees
powerpc/85xx: clean up FPGA device tree nodes for Freecsale QorIQ boards
powerpc/85xx: fix PHYS_64BIT selection for P1022DS
powerpc/fsl-booke: Fix setup_initial_memory_limit to not blindly map
powerpc: respect mem= setting for early memory limit setup
powerpc: Update corenet64_smp_defconfig
powerpc: Update mpc85xx/corenet 32-bit defconfigs
...
Fix up trivial conflicts in:
- arch/powerpc/configs/40x/hcu4_defconfig
removed stale file, edited elsewhere
- arch/powerpc/include/asm/udbg.h, arch/powerpc/kernel/udbg.c:
added opal and gelic drivers vs added ePAPR driver
- drivers/tty/serial/8250.c
moved UPIO_TSI to powerpc vs removed UPIO_DWAPB support
The P3060QDS is a Freescale reference board that hosts the six-core P3060 SOC.
The P3060 Processor combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
P3060QDS Board Overview:
Memory subsystem:
- 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
- 128M Bytes NOR flash single-chip memory
- 16M Bytes SPI flash
- 8K Bytes AT24C64 I2C EEPROM
Ethernet:
- 4x1G + 4x1G/2.5G Ethernet controllers
- 2xRGMII + 1xMII, three VSC8641 PHYs on board
- Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3
PCIe: Two PCI Express 2.0 controllers/ports
USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board
I2C: Four I2C controllers
UART: Supports up to four UARTs
RapidIO: Supports two serial RapidIO ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE DTBs were not updated when the Gianfar driver was converted to an
of_platform_driver in commit b31a1d8b41. Update
the DTBs, adding the required TBI entries.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Adding new device tree binding file for the DCSR node. Modifying device
tree dtsi files to add DCSR node for P2041, P3041, P4080, & P5020.
Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Standarize and document the FPGA nodes used on Freescale QorIQ reference
boards. There are different kinds of FPGAs used on the boards, but
only two are currently standard: "pixis", "ngpixis", and "qixis". Although
there are minor differences among the boards that have one kind of FPGA, most
of the functionality is the same, so it makes sense to create common
compatibility strings.
We also need to update the P1022DS platform file, because the compatible
string for its PIXIS node has changed. This means that older kernels are
not compatible with newer device trees. This is not a real problem, however,
since that particular function doesn't work anyway. When the DIU is active,
the PIXIS is in "indirect mode", and so cannot be accessed as a memory-mapped
device.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's only p2041rdb board for official release, but the p2041 silicon
on the board can be converted to p2040 silicon without XAUI and L2 cache
function, then the board becomes p2040rdb board. so we use the file name
p2041_rdb.c to handle P2040RDB board and P2041RDB board which is also
consistent with the board name under U-Boot.
During the rename we make few other minor changes to the device tree:
* Move USB phy setting into p2041si.dtsi as its SoC not board defined
* Convert PCI clock-frequency to decimal to be more readable
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P4080 silicon device tree was using PowerPC,4080 while the other
e500mc based SoCs used PowerPC,e500mc. Use the core name to be
consistent going forward.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
timer0 and timer1 pins are used as simple GPIO on this board.
Add gpio-controller and #gpio-cells properties to timer nodes
so that we can control gpio lines using available MPC52xx
GPT driver.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Add new nodes to describe more hardware the board is
equipped with:
- two can nodes for SJA1000 on localbus
- pci node to support Coral-PA graphics controller
- serial node for SC28L92 DUART on localbus
- spi node for MSP430 device
Also correct i2c eeprom node name.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This adds a skeletton for the new Power "Non Virtualized"
platform which will be used by machines supporting running
without an hypervisor, for example in order to run KVM.
These machines will be using a new firmware called OPAL
for which the support will be provided by later patches.
The PowerNV platform is intended to be also usable under
the BML environment used internally for early CPU bringup
which is why the code also supports using RTAS instead of
OPAL in various places.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Currently, the build can (very rarely) fail to build because libfdt.h has
not been created or is in the process of being copied.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In the p1023rds, a physical bus of nor flash is 16 bits width.
The bank-width is width (in bytes) of the bus width. So, the
value of bank-width of nor flash is not one, and it should be
two.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch cleans up the documentation of the device-tree binding for
the Flexcan devices on Freescale's PowerPC and ARM cores. Extra
properties are not used by the driver so we are removing them.
Signed-off-by: Robin Holt <holt@sgi.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>,
Acked-by: Wolfgang Grandegger <wg@grandegger.com>,
Cc: U Bhaskar-B22300 <B22300@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: socketcan-core@lists.berlios.de,
Cc: netdev@vger.kernel.org,
Cc: PPC list <linuxppc-dev@lists.ozlabs.org>
Cc: devicetree-discuss@lists.ozlabs.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Taishan (440GX) has the first PHY (EMAC2) mapped at PHY address 1
and the 2nd PHY (EMAC3) at PHY address 3. Use "phy-address" to
correctly describe this instead of "phy-map".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
For AMP, different kernel instances load into separate memory regions.
Read the start of memory from the device tree and limit the memory to what's
specified in the device tree.
Signed-off-by: Dave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
On P1022DS both ethernet controllers are connected to RGMII PHYs
accessible via MDIO bus. Remove fixed-link property from ethernet
nodes as they only required when fixed link PHYs without MDIO bus
are used.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2040RDB Specification:
-----------------------
2Gbyte unbuffered DDR3 SDRAM SO-DIMM(64bit bus)
128 Mbyte NOR flash single-chip memory
256 Kbit M24256 I2C EEPROM
16 Mbyte SPI memory
SD connector to interface with the SD memory card
dTSEC1: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC2: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC3: connected to the Vitesse SGMII PHY (VSC8221)
dTSEC4: connected to the Vitesse RGMII PHY (VSC8641)
dTSEC5: connected to the Vitesse RGMII PHY (VSC8641)
I2C1: Real time clock, Temperature sensor
I2C2: Vcore Regulator, 256Kbit I2C Bus EEPROM
SATA: Lanes C and Land D of Bank2 are connected to two SATA connectors
UART: supports two UARTs up to 115200 bps for console
USB 2.0: connected via a internal UTMI PHY to two TYPE-A interfaces
PCIe:
- Lanes E, F, G and H of Bank1 are connected to one x4 PCIe SLOT1
- Lanes C and Land D of Bank2 are connected to one x4 PCIe SLOT2
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This will allow the new HW RNG driver to bind on these boards
Signed-off-by: Mike Williams <mike@mikebwilliams.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The Sequoia board has a Security function IP block on it that contains a TRNG.
Add the crypto and rng portions of that IP block to the DTS.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
P1010RDB Overview
-----------------
1Gbyte DDR3 (on board DDR)
32Mbyte 16bit NOR flash
32Mbyte SLC NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
I2C Board 128x8 bit memory
SD/MMC connector to interface with the SD memory card
2 SATA interface
1 internal SATA connect to 2.5. 160G SATA2 HDD
1 eSATA connector to rear panel
USB 2.0
x1 USB 2.0 port: connected via a UTMI PHY to Mini-AB interface.
x1 USB 2.0 port: directly connected to Mini-AB interface Ethernet
eTSEC1: Connected to RGMII PHY VSC8641XKO
eTSEC2: Connected to SGMII PHY VSC8221
eTSEC3: Connected to SGMII PHY VSC8221 eCAN
Two DB-9 female connectors for Field bus interface UART
DUART interface: supports two UARTs up to 115200 bps for console display
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Split out common (non-board specific) parts of the SoC related device
tree into a stub so multiple board dts files can include it and we can
reduce duplication and maintenance effort.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fsl-lbc driver requires an interrupt to bind to localbus device.
Populate 85xx boards' dts trees with lbc interrupt info.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 processor is an e500v2 based SoC that utilizes the DPAA
networking architecture. This adds basic board support for non-DPAA
functionality (device tree, board file, etc).
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Added BSD dual-license
* Moved mpic-parent to root so we dont need to duplicate everywhere
* Added next level cache from L2 to CPC
* Moved to 4-cell MPIC interrupt properties
* Added 3 MSI banks
* Added numerous missing nodes: soc-sram-error, guts, pins, clockgen,
rcpm, sfp, serdes, etc.
* Reworked PCIe interrupts to be at virtual bridge level
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P3041DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic device tree for P5020DS board. This device tree excludes
support for DPAA and RapidIO nodes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the Freescale P1022DS reference board, the SSI audio controller is
connected in "asynchronous" mode to the codec's clocks, so the device tree
needs an "fsl,ssi-asynchronous" property.
Also remove the clock-frequency property from the wm8776 node, because
the clock is enabled only if U-Boot enables it, and U-Boot will set the
property if the clock is enabled. A future version of the P1022DS audio
driver will configure the clock itself, but for now, the driver should
not be told that the clock is running when it isn't.
Also fix the FIFO depth to 15, instead of 16.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
dtc was moved and .gitignores have been added to the new location. So, we can
delete the old, forgotten ones.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds MSI support for 440SPe, 460Ex, 460Sx and 405Ex.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Tirumala R Marri <tmarri@apm.com>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The eTSEC includes a PTP clock with quite a few features. This patch adds
support for the basic clock adjustment functions, plus two external time
stamps, one alarm, and the PPS callback.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (45 commits)
crypto: caam - add support for sha512 variants of existing AEAD algorithms
crypto: caam - remove unused authkeylen from caam_ctx
crypto: caam - fix decryption shared vs. non-shared key setting
crypto: caam - platform_bus_type migration
crypto: aesni-intel - fix aesni build on i386
crypto: aesni-intel - Merge with fpu.ko
crypto: mv_cesa - make count_sgs() null-pointer proof
crypto: mv_cesa - copy remaining bytes to SRAM only when needed
crypto: mv_cesa - move digest state initialisation to a better place
crypto: mv_cesa - fill inner/outer IV fields only in HMAC case
crypto: mv_cesa - refactor copy_src_to_buf()
crypto: mv_cesa - no need to save digest state after the last chunk
crypto: mv_cesa - print a warning when registration of AES algos fail
crypto: mv_cesa - drop this call to mv_hash_final from mv_hash_finup
crypto: mv_cesa - the descriptor pointer register needs to be set just once
crypto: mv_cesa - use ablkcipher_request_cast instead of the manual container_of
crypto: caam - fix printk recursion for long error texts
crypto: caam - remove unused keylen from session context
hwrng: amd - enable AMD hw rnd driver for Maple PPC boards
hwrng: amd - manage resource allocation
...
Create the dts files for each core and splits the devices between the two
cores for P1020RDB.
Core0 has core0 to have memory, l2, i2c, spi, gpio, tdm, dma, usb, eth1,
eth2, sdhc, crypto, global-util, message, pci0, pci1, msi.
Core1 has l2, eth0, crypto.
MPIC is shared between two cores but each core will protect its interrupts
from other core by using "protected-sources" of mpic.
Fix compatible property for global-util node of P1020si.dtsi.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PCIe device in legacy mode can trigger interrupts using the wires #INTA,
#INTB ,#INTC and #INTD. PCI devices are obligated to use #INTx for
interrupts under legacy mode. Each PCI slot or device is typically wired
to different inputs on the interrupt controller.
So, Define interrupt-map and interrupt-map-mask properties for device tree
to of map each PCI interrupt signal to the inputs of the interrupt
controller.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P2020si.dtsi, containing information for P2020 SoC. Modifies dts
files for P2020 based systems to use dtsi file.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Creates P1020si.dtsi, containing information for the P1020 SoC. Modifies dts
files for P1020 based systems to use dtsi file
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Grant Likely <grant.likelY@secretlab.ca>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is no hardware interrupt 0xf7. But now we can express the timer
interrupt using 4-cell interrupts. This requires converting all of the
other interrupt specifiers in the tree as well.
Also add the second timer group, and fix the reg property to only
describe the timer registers.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The timestamps recorded in the .gz files add no value.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a first cut at making bootwrapper code which will
produce a zImage compliant with the requirements set down
by ePAPR.
This is a very simple bootwrapper, taking the device tree
blob supplied by the ePAPR boot program and passing it on
to the kernel. It builds on the earlier patch to build a
relocatable ET_DYN zImage to meet the other ePAPR image
requirements.
For good measure we have some paranoid checks which will
generate warnings if some of the ePAPR entry condition
guarantees are not met.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch adds code, linker script and makefile support to allow
building the zImage wrapper around the kernel as a position independent
executable. This results in an ET_DYN instead of an ET_EXEC ELF output
file, which can be loaded at any location by the firmware and will
process its own relocations to work correctly at the loaded address.
This is of interest particularly since the standard ePAPR image format
must be an ET_DYN (although this patch alone is not sufficient to
produce a fully ePAPR compliant boot image).
Note for now we don't enable building with -pie for anything.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
PCIe memory address space is 1:1 mapped with u-boot.
Update dts of Px020RDB i.e. P1020RDB and P2020RDB to match the address map
changes in u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- all the integration parameters have been captured by the binding.
- the block name really uniquely identifies this hardware.
Some advocate putting SoC names everywhere in case software needs
to work around some chip-specific bug, but more precise SoC
information already exists in SVR, and board information already
exists in the top-level device tree node.
Note that sometimes the SoC name is a worse identifier than the
block version, as the block version can change between revisions
of the same SoC.
As a matter of historical reference, neither SEC versions 2.x
nor 3.x (driven by talitos) ever needed CHIP references.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Help clarify that the number trailing in compatible nomenclature
is the version number of the device, i.e., change:
"fsl,p4080-sec4.0", "fsl,sec4.0";
to:
"fsl,p4080-sec-v4.0", "fsl,sec-v4.0";
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Steve Cornelius <sec@pobox.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The SEC4 supercedes the SEC2.x/3.x as Freescale's
Integrated Security Engine. Its programming model is
incompatible with all prior versions of the SEC (talitos).
The SEC4 is also known as the Cryptographic Accelerator
and Assurance Module (CAAM); this driver is named caam.
This initial submission does not include support for Data Path
mode operation - AEAD descriptors are submitted via the job
ring interface, while the Queue Interface (QI) is enabled
for use by others. Only AEAD algorithms are implemented
at this time, for use with IPsec.
Many thanks to the Freescale STC team for their contributions
to this driver.
Signed-off-by: Steve Cornelius <sec@pobox.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Update p1022 sata compatible to "fsl,p1022-sata", "fsl,pq-sata-v2".
p1022ds sata controller is v2 version comparing previous FSL sata
controller, for example, mpc8536.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC852 based mgsuvd board from Keymile was initially ported,
but later on not developed further. This patch removes the respective
files to decrease merging conflicts and unneeded maintenance.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher<hs@denx.de>
Cc: Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Marcelo Tosatti <marcelo@kvack.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The mgcoge board from keymile is now base for some other
similar boards. Therefore the board specific name mgcoge
was renamed to a generic name km82xx. Additionally some
enhancements were made:
- rework partition table in dts file
- add cpm2_pio_c gpio controller in dts file
- update defconfig
- add pin description for SCC1
- add pin description and configuration for USB
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside the MPC 8360 based board kmeter1 other km83xx boards
from keymile will follow. Therefore the board specific naming
kmeter1 for functions and files were replaced with km83xx.
Additionally some updates were made:
- update defconfig for 2.6.38
- rework flash partitioning in dts file
- add gpio controller for qe_pio_c in dts
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Heiko Schocher <hs@denx.de>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fix is a reset for USB PHY that requires some amount of time for power
to be stable on Canyonlands.
Signed-off-by: Rupjyoti Sarmah <rsarmah@apm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The dts-installed variable is initialised using a wildcard path that
will be expanded relative to the build directory. Use the existing
variable dtstree to generate an absolute wildcard path that will work
when building in a separate directory.
Reported-by: Gerhard Pircher <gerhard_pircher@gmx.net>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Gerhard Pircher <gerhard_pircher@gmx.net> [against 2.6.32]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
In order to prevent the fsl_dma driver from claiming the DMA channels that the
P1022DS audio driver needs, the compatible properties for those nodes must say
"fsl,ssi-dma-channel" instead of "fsl,eloplus-dma-channel".
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8308 has ULPI pin muxing settings in SICRH register, bits 17-18
which is different from both MPC8313 and MPC8315.
Also MPC8308 doesn't have REFSEL, UTMI_PHY_EN and OTG_PORT fields
in the USB DR controller CONTROL register.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (72 commits)
powerpc/pseries: Fix build of topology stuff without CONFIG_NUMA
powerpc/pseries: Fix VPHN build errors on non-SMP systems
powerpc/83xx: add mpc8308_p1m DMA controller device-tree node
powerpc/83xx: add DMA controller to mpc8308 device-tree node
powerpc/512x: try to free dma descriptors in case of allocation failure
powerpc/512x: add MPC8308 dma support
powerpc/512x: fix the hanged dma transfer issue
powerpc/512x: scatter/gather dma fix
powerpc/powermac: Make auto-loading of therm_pm72 possible
of/address: Use propper endianess in get_flags
powerpc/pci: Use printf extension %pR for struct resource
powerpc: Remove unnecessary casts of void ptr
powerpc: Disable VPHN polling during a suspend operation
powerpc/pseries: Poll VPA for topology changes and update NUMA maps
powerpc: iommu: Add device name to iommu error printks
powerpc: Record vma->phys_addr in ioremap()
powerpc: Update compat_arch_ptrace
powerpc: Fix PPC_PTRACE_SETHWDEBUG on PPC_BOOK3S
powerpc/time: printk time stamp init not correct
powerpc: Minor cleanups for machdep.h
...
This patch creates mpc5200b.dtsi containing the information for the MPC5200b
SoC then modifies all of the dts files for MPC5200b based systems to use
mpc5200b.dtsi.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch changes some incorrect compatible strings on the local plus bus node
in dts files for MPC5200b based systems.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch remove unused properties in dts files in preparation of refactoring
the dts files for MPC5200b based boards.
Signed-off-by: John Bonesio <bones@secretlab.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
