Commit 4bb25789ed ("arm: dma-mapping: plumb our iommu mapping ops
into arch_setup_dma_ops") moved the setting of the DMA operations from
arm_iommu_attach_device() to arch_setup_dma_ops() where the DMA
operations to be used are selected based on whether the device is
connected to an IOMMU. However, the IOMMU detection scheme requires the
IOMMU driver to be ported to the new IOMMU of_xlate API. As no driver
has been ported yet, this effectively breaks all IOMMU ARM users that
depend on the IOMMU being handled transparently by the DMA mapping API.
Fix this by restoring the setting of DMA IOMMU ops in
arm_iommu_attach_device() and splitting the rest of the function into a
new internal __arm_iommu_attach_device() function, called by
arch_setup_dma_ops().
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
375/38x. Only switch the PL310 to I/O coherent mode if I/O coherency
is enabled.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qzYQ
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-3.19-6' of git://git.infradead.org/linux-mvebu into fixes
Merge "mvebu-fixes-6" from Andrew Lunn:
The previous fix for Armada XP, disabling I/O coherency, broke Armada
375/38x. Only switch the PL310 to I/O coherent mode if I/O coherency
is enabled.
* tag 'mvebu-fixes-3.19-6' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
Signed-off-by: Olof Johansson <olof@lixom.net>
Since commit f2c3c67f00 (merge commit that adds commit "ARM: mvebu:
completely disable hardware I/O coherency"), we disable I/O coherency
on Armada EBU platforms.
However, we continue to initialize the coherency fabric, because this
coherency fabric is needed on Armada XP for inter-CPU
coherency. Unfortunately, due to this, we also continued to execute
the coherency fabric initialization code for Armada 375/38x, which
switched the PL310 into I/O coherent mode. This has the effect of
disabling the outer cache sync operation: this is needed when I/O
coherency is enabled to work around a PCIe/L2 deadlock. But obviously,
when I/O coherency is disabled, having the outer cache sync operation
is crucial.
Therefore, this commit fixes the armada_375_380_coherency_init() so
that the PL310 is switched to I/O coherent mode only if I/O coherency
is enabled.
Without this fix, all devices using DMA are broken on Armada 375/38x.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Cc: <stable@vger.kernel.org> # v3.8+
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLlc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.19" from Maxime Ripard:
Allwinner fixes for 3.19
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit f77d55a3b5 ("serial: 8250_dw: get index of serial line from DT
aliases") made the serial driver now use the serial aliases to get the tty
number, pointing out that our aliases have been wrong all along.
Remove them from the DTSI and add custom ones in the relevant boards.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- Correct pwm clock assignment in i.MX25 device tree to fix the broken
pwm support on i.MX25
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUwZrwAAoJEFBXWFqHsHzOEMoH/iIU+ChvOXbJe7DfITJiwPXG
hjILxqR4sjcJAIfd3y67ydD4fg6wRf/Gfp3tij/Ydbjrl7TbWOaQveo7Uolr6Jaj
MiXXOvQDyISHNoS09UjmCf8+4VSDx+5hamkWSlJTXC365RI6PAQihduvCWCUF5/Y
GwUaZBNTOE8VMgel20BKmvGKGPwJDAw3K5jO5Lfwg2DYLDSqZEHa+kuOxgBjbRJp
2VkrNplkVQ7QAO4HrNIuyVSXXvgSS4fJQ1unbd+EgRBkh2yLUAOlHmOXxZouYTbh
uPr7rp2Q4pDruJj/C2O9t5ng2nnMQ6I1z54umJp+2h0VSsNOX2ZjLTHq7/SvyHE=
=SrqB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.19, 2nd round" from Shawn Guo:
The i.MX fixes for 3.19, 2nd round:
- Correct pwm clock assignment in i.MX25 device tree to fix the broken
pwm support on i.MX25
* tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx25: Fix PWM "per" clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
Without explicit command-line parameters, the Juno UART ends up running
at 57600 baud in the kernel, which is at odds with the 115200 baud used
by the rest of the firmware. Since commit 7914a7c565 now lets us
fix this by specifying default options in stdout-path, do so.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Mb4f
-----END PGP SIGNATURE-----
Merge tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Merge "Second Round of Renesas ARM Based SoC Fixes for v3.19" from Simon
Horman:
* Instantiate GIC from C board code in legacy builds on r8a7778 and r8a7779
* tag 'renesas-soc-fixes2-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a7778: Instantiate GIC from C board code in legacy builds
Signed-off-by: Olof Johansson <olof@lixom.net>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lpO3
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
On Armada XP, 375 and 38x the MBus window 13 has the remap capability,
like windows 0 to 7. However, the mvebu-mbus driver isn't currently
taking into account this special case, which means that when window 13
is actually used, the remap registers are left to 0, making the device
using this MBus window unavailable.
As a minimal fix for stable, don't use window 13. A full fix will
follow later.
Fixes: fddddb52a6 ("bus: introduce an Marvell EBU MBus driver")
Cc: <stable@vger.kernel.org> # v3.10+
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The current hardware I/O coherency is known to cause problems with DMA
coherent buffers, as it still requires explicit I/O synchronization
barriers, which is not compatible with the semantics expected by the
Linux DMA coherent buffers API.
So, in order to have enough time to validate a new solution based on
automatic I/O synchronization barriers, this commit disables hardware
I/O coherency entirely. Future patches will re-enable it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq domain")
changed the GIC driver to use a non-legacy IRQ domain on DT
platforms. This patch assumes that DT-driven systems are getting
all of their interrupts from device tree.
Turns out that OMAP has quite a few hidden gems, and still uses
hardcoded interrupts despite having fairly complete DTs.
This patch attempts to work around these by offering a translation
method that can be called directly from the hwmod code, if present.
The same hack is sprinkled over PRCM and TWL.
It isn't pretty, but it seems to do the job without having to add
more hacks to the interrupt controller code.
Tested on OMAP4 (Panda-ES) and OMAP5 (UEVM5432).
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: updated to fix make randconfig issue]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Call spin_lock_init() before the spinlocks are used, both in early init
and probe functions preventing a lockdep splat.
I have been observing lockdep complaining [1] during boot on my a80 optimus [2]
when CONFIG_PROVE_LOCKING has been enabled. This patch resolves the splat,
and has been tested on a few other sunxi platforms without issue.
[1] http://storage.kernelci.org/next/next-20150107/arm-multi_v7_defconfig+CONFIG_PROVE_LOCKING=y/lab-tbaker/boot-sun9i-a80-optimus.html
[2] http://kernelci.org/boot/?a80-optimus
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "Renesas ARM Based SoC Fixes for v3.19" from Simon Horman:
Renesas ARM Based SoC Fixes for v3.19
This pull request is based on the last round of SoC updates for v3.19,
Fourth Round of Renesas ARM Based SoC Updates for v3.19, tagged as
renesas-soc3-for-v3.19, merged into your next/soc branch and included in
v3.19-rc1.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
Set .control_parent for all irqpin instances for sh73a0 SoC when booting
using legacy C.
- ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
This fixes a long standing problem which has been present since
the sh73a0 SoC started using the INTC External IRQ pin driver.
The patch that introduced the problem is 341eb5465f ("ARM:
shmobile: INTC External IRQ pin driver on sh73a0") which was included
in v3.10.
* tag 'renesas-soc-fixes-for-v3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: shmobile: r8a7740: Instantiate GIC from C board code in legacy builds
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
The arm-cci driver completes the probe sequence even if the cci node is
marked as disabled. Add a check in the driver to honour the cci status
in the device tree.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
rk3288 SoCs have a function to automatically switch between jtag/sdmmc pinmux
settings depending on the card state. This collides with a lot of assumptions.
It only works when using the internal card-detect mechanism and breaks
horribly when using either the normal card-detect via the slot-gpio function
or via any other pin. Also there is of course no link between the mmc and jtag
on the software-side, so the jtag clocks may very well be disabled when the
card is ejected and the soc switches back to the jtag pinmux.
Leaving the switching function enabled did result in mmc timeouts and rcu
stalls thus hanging the system on 3.19-rc1. Therefore disable it in all cases,
as we expect the devicetree to explicitly select either mmc or jtag pinmuxes
anyway.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), Marzen legacy hangs during boot with:
Image Name: 'Linux-3.19.0-rc4'
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3445880 Bytes = 3.3 MiB
Load Address: 60008000
Entry Point: 60008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK
Starting kernel ...
Enabling DEBUG_LL does not seem to change the situation, however this
patch by itself fixes this issue and re-enables normal boot.
This issue happens because the IRQ numbers of the GIC are now virtual,
and no longer match the hardcoded hardware IRQ numbers in the platform
board code.
To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0, r8a7740 and r8a7778 legacy code.
Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 9a1091ef00 ("irqchip: gic: Support hierarchy irq
domain."), Bock-W legacy hangs during boot with:
Unable to handle kernel paging request at virtual address cf86a128
pgd = c0004000
[cf86a128] *pgd=6f80041e(bad)
Internal error: Oops: 8000000d [#1] SMP ARM
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.19.0-rc4 #1
Hardware name: bockw
task: cf823b40 ti: cf824000 task.ti: cf824000
PC is at 0xcf86a128
LR is at request_threaded_irq+0xbc/0x124
This happens because the IRQ numbers of the GIC are now virtual, and no
longer match the hardcoded hardware IRQ numbers in the platform board
code.
To fix this, instantiate the GIC from platform board code when compiling
a legacy kernel, like is done for the sh73a0 and r8a7740 legacy code.
Follows same style as the r8a7740 legacy GIC fix by Geert Uytterhoeven,
thanks to him for the initial work.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Whenever Suspend PHY bit is set on DRA7x devices,
USB will not work due to Set EP Configuration command
always failing.
This was only found after a recent commit 2164a47 (usb:
dwc3: set SUSPHY bit for all cores, which will be merged
for v3.19) added a missing *required* step to dwc3
initialization. Synopsys Databook requires that we enable
Suspend PHY bit after initialization but that, unfortunately,
breaks DRA7x.
Note that the same regression was already patched for AM437x.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Appearance: On some SAMA5D4EK boards, after power up, the Eth1 doesn't work.
Reason: The PIOE2 pin is connected to the NAND_Tree# of KSZ8081,
But it outputs LOW during the reset period, which cause the NAND_Tree# enabled.
Add phy_fixup() to disable NAND_Tree by overriding the Operation
Mode Strap Override register(i.e. Register 16h) to clear the NAND_Tree bit.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
atmel_lcdfb needs also uses hclk clock, but AT91SAM9263 doesn't have that
specific clock, so use lcd_clk twice. The same was done in
arch/arm/mach-at91/at91sam9263.c
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The second property of reg is the length, so correct it for timer.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
multi_v7_defconfig has it as Y already, so build it in here, too, for
consistency, and therefore build in HWMON as well.
Signed-off-by: Andreas Faerber <afaerber@suse.de>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Many Exynos devices have a display panel. Most of them just have
a simple panel while others have more complex configurations that
requires an embedded DisplayPort (eDP) to LVDS bridges.
This patch enables the following features to be built in the kernel
image to support both setups:
- Direct Rendering Manager (DRM)
- DRM bridge registration and lookup framework
- Parade ps8622/ps8625 eDP/LVDS bridge
- NXP ptn3460 eDP/LVDS bridge
- Exynos Fully Interactive Mobile Display controller (FIMD)
- Panel registration and lookup framework
- Simple panels
- Backlight & LCD device support
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull ARM fixes from Russell King:
"Three small fixes from over the Christmas period, and wiring up the
new execveat syscall for ARM"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8275/1: mm: fix PMD_SECT_RDONLY undeclared compile error
ARM: 8253/1: mm: use phys_addr_t type in map_lowmem() for kernel mem region
ARM: 8249/1: mm: dump: don't skip regions
ARM: wire up execveat syscall
Pull x86 fixes from Ingo Molnar:
"Misc fixes: two vdso fixes, two kbuild fixes and a boot failure fix
with certain odd memory mappings"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, vdso: Use asm volatile in __getcpu
x86/build: Clean auto-generated processor feature files
x86: Fix mkcapflags.sh bash-ism
x86: Fix step size adjustment during initial memory mapping
x86_64, vdso: Fix the vdso address randomization algorithm
Pull scheduler fixes from Ingo Molnar:
"Misc fixes: group scheduling corner case fix, two deadline scheduler
fixes, effective_load() overflow fix, nested sleep fix, 6144 CPUs
system fix"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/fair: Fix RCU stall upon -ENOMEM in sched_create_group()
sched/deadline: Avoid double-accounting in case of missed deadlines
sched/deadline: Fix migration of SCHED_DEADLINE tasks
sched: Fix odd values in effective_load() calculations
sched, fanotify: Deal with nested sleeps
sched: Fix KMALLOC_MAX_SIZE overflow during cpumask allocation
Pull perf fixes from Ingo Molnar:
"Mostly tooling fixes, but also some kernel side fixes: uncore PMU
driver fix, user regs sampling fix and an instruction decoder fix that
unbreaks PEBS precise sampling"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86/uncore/hsw-ep: Handle systems with only two SBOXes
perf/x86_64: Improve user regs sampling
perf: Move task_pt_regs sampling into arch code
x86: Fix off-by-one in instruction decoder
perf hists browser: Fix segfault when showing callchain
perf callchain: Free callchains when hist entries are deleted
perf hists: Fix children sort key behavior
perf diff: Fix to sort by baseline field by default
perf list: Fix --raw-dump option
perf probe: Fix crash in dwarf_getcfi_elf
perf probe: Fix to fall back to find probe point in symbols
perf callchain: Append callchains only when requested
perf ui/tui: Print backtrace symbols when segfault occurs
perf report: Show progress bar for output resorting
Pull locking fixes from Ingo Molnar:
"A liblockdep fix and a mutex_unlock() mutex-debugging fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
mutex: Always clear owner field upon mutex_unlock()
tools/liblockdep: Fix debug_check thinko in mutex destroy
Fix for BUG_ON(anon_vma->degree) splashes in unlink_anon_vmas() ("kernel
BUG at mm/rmap.c:399!") caused by commit 7a3ef208e6 ("mm: prevent
endless growth of anon_vma hierarchy")
Anon_vma_clone() is usually called for a copy of source vma in
destination argument. If source vma has anon_vma it should be already
in dst->anon_vma. NULL in dst->anon_vma is used as a sign that it's
called from anon_vma_fork(). In this case anon_vma_clone() finds
anon_vma for reusing.
Vma_adjust() calls it differently and this breaks anon_vma reusing
logic: anon_vma_clone() links vma to old anon_vma and updates degree
counters but vma_adjust() overrides vma->anon_vma right after that. As
a result final unlink_anon_vmas() decrements degree for wrong anon_vma.
This patch assigns ->anon_vma before calling anon_vma_clone().
Signed-off-by: Konstantin Khlebnikov <koct9i@gmail.com>
Reported-and-tested-by: Chris Clayton <chris2553@googlemail.com>
Reported-and-tested-by: Oded Gabbay <oded.gabbay@amd.com>
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Daniel Forrest <dan.forrest@ssec.wisc.edu>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: stable@vger.kernel.org # to match back-porting of 7a3ef208e6
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit fee7e49d45 ("mm: propagate error from stack expansion even for
guard page") made sure that we return the error properly for stack
growth conditions. It also theorized that counting the guard page
towards the stack limit might break something, but also said "Let's see
if anybody notices".
Somebody did notice. Apparently android-x86 sets the stack limit very
close to the limit indeed, and including the guard page in the rlimit
check causes the android 'zygote' process problems.
So this adds the (fairly trivial) code to make the stack rlimit check be
against the actual real stack size, rather than the size of the vma that
includes the guard page.
Reported-and-tested-by: Chih-Wei Huang <cwhuang@android-x86.org>
Cc: Jay Foad <jay.foad@gmail.com>
Cc: stable@kernel.org # to match back-porting of fee7e49d45
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just one fix: a qlogic busy wait regression.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJUsDZnAAoJEDeqqVYsXL0MWJYH/jJ3F3H2p605JZ32vbrG7l4n
ZoWSMkNkxVPyqWmmQCWL7vL0oTF98GdxzwQHqqQd/7CeubnE0HXuLQMfqmhy4Jgm
I3xOKZ+zjCD/Rvad5ei3poz8k21yLDZl72eEAuc3rawrtLKQnaaDJSJeyulF8KNj
BfJoEy7ozdNwbXpbofGb8O4+aI0p0Mdnl9mb5VIM05H33FtCUT+eHlOh73trAR+7
knuevoLN/UwL3I0HnBSoidE53e3MM+7Cb2MUhYjK3gBx2jbhl1LJSh9G38Iuxu9s
+W/6yZ8jHrivtSCrETzZkp2Z4v6yYCH8q+0rvJBWry9qf55XTXaUf2IdSBtEoK0=
=GL15
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Just one fix: a qlogic busy wait regression"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
qla2xxx: fix busy wait regression
All a few small regression or stable fixes: a Nvidia HDMI ID addition,
a regression fix for CAIAQ stream count, a typo fix for GPIO setup
with STAC/IDT HD-audio codecs, and a Fireworks big-endian fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=qYdK
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"All a few small regression or stable fixes: a Nvidia HDMI ID addition,
a regression fix for CAIAQ stream count, a typo fix for GPIO setup
with STAC/IDT HD-audio codecs, and a Fireworks big-endian fix"
* tag 'sound-3.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: fireworks: fix an endianness bug for transaction length
ALSA: hda - Add new GPU codec ID 0x10de0072 to snd-hda
ALSA: hda - Fix wrong gpio_dir & gpio_mask hint setups for IDT/STAC codecs
ALSA: snd-usb-caiaq: fix stream count check
Pull HID updates from Jiri Kosina:
- bounds checking fixes in logitech and roccat drivers, from Peter Wu
and Dan Carpenter
- double-kfree fix in i2c-hid driver on bus shutdown, from Mika
Westerberg
- a couple of various small driver fixes
- a few device id additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: roccat: potential out of bounds in pyra_sysfs_write_settings()
HID: Add a new id 0x501a for Genius MousePen i608X
HID: logitech-hidpp: prefix the name with "Logitech"
HID: logitech-hidpp: avoid unintended fall-through
HID: Allow HID_BATTERY_STRENGTH to be enabled
HID: i2c-hid: Do not free buffers in i2c_hid_stop()
HID: add battery quirk for USB_DEVICE_ID_APPLE_ALU_WIRELESS_2011_ISO keyboard
HID: logitech-hidpp: check WTP report length
HID: logitech-dj: check report length
