Commit Graph

23349 Commits

Author SHA1 Message Date
Johannes Berg
6fb5511ab9 iwlagn: advertise reliable TX status
Our hardware has reliable TX status, but we're
not currently advertising that to mac80211.
Since the packet loss monitoring will depend
on it, advertise it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-24 16:58:26 -08:00
Johannes Berg
2e34034e8c iwlagn: fix station powersave accounting for aggregation
Since aggregation queues are station-specific, the
device will not reject packets in them but rather
will stop the appropriate aggregation queues when
a station goes to sleep. I forgot to account for
this in the driver, so if a station went to sleep
that had aggregation enabled, traffic would stop
indefinitely.

Fix this by only accounting frames queued on the
normal AC queues for associated station.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-24 16:58:15 -08:00
Johannes Berg
67158b67ce iwlagn: remove powersave warning
Through races, a packet may be enqueued for
transmission to a station while that station
is going to sleep, in which case the warning
here triggers. Instead of warning, check the
condition -- if this packet is not a PS-poll
response then we still enqueue it but it will
be rejected by the device since the station
is marked as asleep.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-24 16:58:06 -08:00
Wey-Yi Guy
dbbf1755b0 iwlwifi: use antenna information in EEPROM
The valid tx/rx antenna information is part of EEPROM, so use it
to configure the device.

For few cases, the EEPROM did not reflect the correct antenna, but
it is too late to modify the EEPROM, so overwrite with .cfg parameters

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-24 16:57:55 -08:00
Wey-Yi Guy
4b7384f936 iwlwifi: remove unused define
was not used, remove it

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-24 16:57:43 -08:00
Felix Fietkau
4f8559383c ath9k_hw: remove ath9k_hw_stoppcurecv
It is no longer used anywhere

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:41 -05:00
Rajkumar Manoharan
fa6e15e0b5 ath9k_htc: Identify devices using driver_info
Categorize AR7010 & AR9287 devices based on driver_info
of usb_device_id, instead of PIDs. This avoids per-device cases
and minimize code changes for new device addition.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:41 -05:00
Rajkumar Manoharan
f7ec8fb4d6 ath9k_hw: Fix eeprom offset for AR9287 devices (PCI/USB)
AR9287 devices (PCI/USB) use different eeprom start location
to read nvram. New devices might endup with same devid. So use
driver_info to set offset, instead of devid. driver_info is
valid for HTC devices alone which is filled in usb_device_id.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:41 -05:00
Rajkumar Manoharan
64f1217083 ath9k_htc: Add driver_info in usb device list
Added driver_info to identify AR7010, R9287 HTC devices.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:40 -05:00
Rajkumar Manoharan
bedbbb959d ath: Add a driver_info bitmask field
The driver_info stores the device category information which
is used to load appropriate device firmware, select firmware offset
and eeprom starting location. The driver_info is accessed across
ath9k_htc and ath9k_hw. Hence placed under common structure.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:40 -05:00
Wey-Yi Guy
35162ba759 iwlwifi: advance power management support
For 6000g2b and up, adding advance power management support
for better power consumption

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:37 -05:00
Wey-Yi Guy
1f37daf323 iwlwifi: power management checking for shadow register
If shadow register is enable, modify the power management
command to inform uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:37 -05:00
Wey-Yi Guy
e366176e5c iwlwifi: consider BT for power management
Check the BT PSPoll flag when fill PM command to uCode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:37 -05:00
Wey-Yi Guy
97badb0eef iwlwifi: add more power management flags
Adding additional power management option available for the device.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:36 -05:00
Wey-Yi Guy
eeb1f83fa8 iwlagn: name change for BT config flag
Bit 7 of BT config flag is used to enable/disable PSPoll sync.
Make the name to match it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:36 -05:00
Luis R. Rodriguez
c8b576061d ath9k: avoid aggregation for VO traffic
This should help with latency issues which can happen when
using aggregation.

Cc: Matt Smith <matt.smith@atheros.com>
Cc: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:35 -05:00
Rafał Miłecki
0b81c23d2e b43: N-PHY: little cleanups
Remove some typos, warnings, initialize some values to follow wl's code path.

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:34 -05:00
Rafał Miłecki
a529cecd29 b43: N-PHY: rev2: save and restore PHY regs on RSSI poll
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:34 -05:00
Rafał Miłecki
fee613b77d b43: N-PHY: fix BPHY init
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:34 -05:00
Rafał Miłecki
bec186452b b43: N-PHY: init BPHY when needed
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:33 -05:00
Rafał Miłecki
a5d3598de0 b43: N-PHY: fix some typos, conditions, set gain_boost
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:33 -05:00
Rafał Miłecki
c0f05b9879 b43: N-PHY: minor fixes to match specs
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:33 -05:00
Rafał Miłecki
69a3229edc b43: N-PHY: fix values for PHY regs in channel tables of 2055 radio
Additional comment by Larry Finger <Larry.Finger@lwfinger.net>:

This change deserves a bit more explanation. You might include something like
"These tables came from reverse engineering the 5.10.56.46 version of the
Broadcom driver. Trace comparisons between b43 and the current Broadcom driver
(5.10.120.0) show byte reversals for the PHY register writes."

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-24 16:19:33 -05:00
John W. Linville
d7a066c923 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 2010-11-24 16:19:24 -05:00
Guennadi Liakhovetski
e476a5a41a wireless: b43: fix error path in SDIO
Fix unbalanced call to sdio_release_host() on the error path.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-23 15:00:51 -05:00
Felix Fietkau
f8afa42b01 ath9k_htc: fix eeprom access
wireless-testing commit a05b5d4504
ath9k: add support for reading eeprom from platform data on PCI devices

This change moved the initialization of the AH_USE_EEPROM flag from ath9k_hw
to ath9k. This needs to be added to ath9k_htc as well

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:56 -05:00
Felix Fietkau
02d2ebb2a0 ath9k_hw: fix A-MPDU key search issues on AR9003
Under load, a large number of frames can produce decryption errors, even when
no key cache update is being done. Performing a key search for every single
frame in an A-MPDU improves reliability.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:55 -05:00
Joe Perches
7253965a1c zd1211rw: Use const
Mark arrays const that are unmodified after initializations.

   text	   data	    bss	    dec	    hex	filename
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.old
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.new

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:54 -05:00
Joe Perches
f4e16e41d6 rt2x00: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  40197	     56	   8336	  48589	   bdcd	drivers/net/wireless/rt2x00/rt2800lib.o.new
  40205	     56	   8336	  48597	   bdd5	drivers/net/wireless/rt2x00/rt2800lib.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:53 -05:00
Joe Perches
22288a5847 rndis_wlan: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  41757	   2205	   9896	  53858	   d262	drivers/net/wireless/rndis_wlan.o.old
  41653	   2205	   9880	  53738	   d1ea	drivers/net/wireless/rndis_wlan.o.new

Changed functions rndis_set_oid and set_bssid to take const *'s.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:52 -05:00
Joe Perches
ff273b91ff ray_cs: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  42607	   3581	   8536	  54724	   d5c4	drivers/net/wireless/ray_cs.o.new
  42603	   3585	   8536	  54724	   d5c4	drivers/net/wireless/ray_cs.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:51 -05:00
Joe Perches
482e039f2a libertas: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
   3650	     56	    704	   4410	   113a	drivers/net/wireless/libertas/rx.o.new
   3695	     56	    704	   4455	   1167	drivers/net/wireless/libertas/rx.o.old
  27328	    964	   5240	  33532	   82fc	drivers/net/wireless/libertas/cfg.o.new
  27328	    964	   5240	  33532	   82fc	drivers/net/wireless/libertas/cfg.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:50 -05:00
Joe Perches
20407ed8a5 iwlwifi: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  48644	     57	  12120	  60821	   ed95	drivers/net/wireless/b43/phy_n.o.new
  48661	     57	  12120	  60838	   eda6	drivers/net/wireless/b43/phy_n.o.old
  37906	     86	   7904	  45896	   b348	drivers/net/wireless/iwlwifi/iwl-agn-lib.o.new
  37937	     86	   7904	  45927	   b367	drivers/net/wireless/iwlwifi/iwl-agn-lib.o.old
  37781	    523	   6752	  45056	   b000	drivers/net/wireless/iwlwifi/iwl-3945.o.new
  37781	    523	   6752	  45056	   b000	drivers/net/wireless/iwlwifi/iwl-3945.o.old

Changed b43_nphy_write_clip_detection to take a const u16 *

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:48 -05:00
Joe Perches
5b4bc649e1 b43: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
   5502	     56	   1336	   6894	   1aee	drivers/net/wireless/b43/phy_common.o.new
   5511	     56	   1336	   6903	   1af7	drivers/net/wireless/b43/phy_common.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:47 -05:00
Joe Perches
3370a89545 atmel: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  42578	    720	   8528	  51826	   ca72	drivers/net/wireless/atmel.o.old
  42578	    720	   8528	  51826	   ca72	drivers/net/wireless/atmel.o.new

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:46 -05:00
Joe Perches
5653a63d85 carl9170: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
   1897	     56	    672	   2625	    a41	drivers/net/wireless/ath/carl9170/cmd.o.new
   1897	     56	    672	   2625	    a41	drivers/net/wireless/ath/carl9170/cmd.o.old

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:45 -05:00
Joe Perches
07b2fa5a23 ath9k: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11161	     56	   2136	  13353	   3429	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.new
  11167	     56	   2136	  13359	   342f	drivers/net/wireless/ath/ath9k/ar9003_paprd.o.old
  15428	     56	   3056	  18540	   486c	drivers/net/wireless/ath/ath9k/eeprom_4k.o.old
  15451	     56	   3056	  18563	   4883	drivers/net/wireless/ath/ath9k/eeprom_4k.o.new
  14087	     56	   2560	  16703	   413f	drivers/net/wireless/ath/ath9k/eeprom_9287.o.old
  14036	     56	   2560	  16652	   410c	drivers/net/wireless/ath/ath9k/eeprom_9287.o.new
  10041	     56	   2384	  12481	   30c1	drivers/net/wireless/ath/ath9k/ani.o.new
  10088	     56	   2384	  12528	   30f0	drivers/net/wireless/ath/ath9k/ani.o.old
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.new
   9316	   1580	   2304	  13200	   3390	drivers/net/wireless/ath/ath9k/htc_drv_init.o.old
  16483	     56	   3432	  19971	   4e03	drivers/net/wireless/ath/ath9k/ar9003_phy.o.new
  16517	     56	   3432	  20005	   4e25	drivers/net/wireless/ath/ath9k/ar9003_phy.o.old
  18221	    104	   2960	  21285	   5325	drivers/net/wireless/ath/ath9k/rc.o.old
  18203	    104	   2960	  21267	   5313	drivers/net/wireless/ath/ath9k/rc.o.new
  19985	     56	   4288	  24329	   5f09	drivers/net/wireless/ath/ath9k/eeprom_def.o.new
  20040	     56	   4288	  24384	   5f40	drivers/net/wireless/ath/ath9k/eeprom_def.o.old
  23997	     56	   4984	  29037	   716d	drivers/net/wireless/ath/ath9k/ar5008_phy.o.old
  23846	     56	   4984	  28886	   70d6	drivers/net/wireless/ath/ath9k/ar5008_phy.o.new
  24285	     56	   3184	  27525	   6b85	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.old
  24101	     56	   3184	  27341	   6acd	drivers/net/wireless/ath/ath9k/ar9003_eeprom.o.new
   6834	     56	   1032	   7922	   1ef2	drivers/net/wireless/ath/ath9k/ar9002_phy.o.old
   6780	     56	   1032	   7868	   1ebc	drivers/net/wireless/ath/ath9k/ar9002_phy.o.new
  36211	     64	   8624	  44899	   af63	drivers/net/wireless/ath/ath9k/hw.o.new
  36401	     64	   8624	  45089	   b021	drivers/net/wireless/ath/ath9k/hw.o.old
   9281	     56	   1496	  10833	   2a51	drivers/net/wireless/ath/ath9k/ar9003_calib.o.old
   9150	     56	   1496	  10702	   29ce	drivers/net/wireless/ath/ath9k/ar9003_calib.o.new

Use ARRAY_SIZE instead of a magic number.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:44 -05:00
Joe Perches
8b22523b04 ath5k: Use static const
Using static const generally increases object text and decreases data size.
It also generally decreases overall object size.

   text	   data	    bss	    dec	    hex	filename
  11266	     56	   2464	  13786	   35da	drivers/net/wireless/ath/ath5k/ani.o.old
  11181	     56	   2464	  13701	   3585	drivers/net/wireless/ath/ath5k/ani.o.new

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:43 -05:00
Joe Perches
85be3d98db ar9170: Use const
Mark an array const.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:42 -05:00
Christian Lamparter
a9ab211335 carl9170: fix init-self regression
The commit: "carl9170: tx path review" introduced a regression.

gcc (with -Winit-self):
tx.c:1264: warning: ‘super’ is used uninitialized in this function

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:41 -05:00
Huang Weiyi
3b1d6dfaaf libertas: remove duplicated #include
Remove duplicated #include('s) in
  drivers/net/wireless/libertas/cfg.c

Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:40 -05:00
Felix Fietkau
e1566d1f32 ath9k: fix recursive locking in the tx flush path
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:38 -05:00
Johannes Berg
b5bb2f2beb iwlwifi: fix modular 3945 only build
If only 3945 is selected, and is a module, build
fails because iwl-legacy.c won't be compiled. Fix
this by adding it to the build correctly.

This doesn't happen for 4965 because it is a bool
option, not tristate, since it's built into the
AGN module.

Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Tested-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:51 -05:00
Rafał Miłecki
8ce4699995 b43: rfkill: use HI enabled bit for all devices
Devices which use LO enabled bit are covered by b43legacy

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:48:50 -05:00
Rafał Miłecki
8933f90c77 b43: N-PHY: add 2056 radio channels tables
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:35:18 -05:00
John W. Linville
840fd8ff64 Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6 2010-11-22 15:28:30 -05:00
Christian Lamparter
b397492a8c carl9170: fix virtual interface setup crash
This patch fixes a faulty bound check which caused a
crash when too many virtual interface were brought up.

BUG: unable to handle kernel NULL pointer dereference at 00000004
IP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
*pde = 00000000
Oops: 0002 [#1] PREEMPT
Modules linked in: carl9170 [...]
Pid: 4720, comm: wpa_supplicant Not tainted 2.6.37-rc2-wl+
EIP: 0060:[<f8125f67>] EFLAGS: 00210206 CPU: 0
EIP is at carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
EAX: 00000000 ...
Process wpa_supplicant
Stack:
 f4f88f34 fffffff4 ..
Call Trace:
 [<f8f4e666>] ? ieee80211_do_open+0x406/0x5c0 [mac80211]
 [...]
Code: <89> 42 04 ...
EIP: [<f8125f67>] carl9170_op_add_interface+0x1d7/0x2c0 [carl9170]
CR2: 0000000000000004

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:19:32 -05:00
Felix Fietkau
d47844a014 ath9k: fix timeout on stopping rx dma
It seems that using ath9k_hw_stoppcurecv to stop rx dma is not enough.
When it's time to stop DMA, the PCU is still busy, so the rx enable
bit never clears.
Using ath9k_hw_abortpcurecv helps with getting rx stopped much faster,
with this change, I cannot reproduce the rx stop related WARN_ON anymore.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:19:31 -05:00
Juuso Oikarinen
b84a7d3d9e wl12xx: Unset bssid filter, ssid and bssid from firmware on disassoc
On the disassociation event from the mac80211, the wl12xx driver does not
clear the chipset configuration related to the AP - i.e. it does not perform
a DISCONNECT and then a JOIN with zero SSID and dummy BSSID. Also, it does not
unset the BSSID filter.

Often this is not a problem, as the above is performed upon entering idle
state. But if a scenario arises where a new association is attempted without
cycling through idle state, the new association will fail.

Fix this by resetting the firmware state on disassociation.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:14 +02:00
Arik Nemtsov
68d069c45f wl1271: add support for HW TX fragmentation
Indicate to mac80211 we support HW fragmentation.
Support updates of the fragmentation threshold via the
set_frag_threshold callback.

Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:13 +02:00
Juuso Oikarinen
fa97f46b30 Revert "wl1271: Change supported channel order for a more optimal scan"
This reverts commit fa21c7a9e4.

The reverted patch caused more harm than benefit.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:12 +02:00
Juuso Oikarinen
b7417d930a wl1271: Prevent ad-hoc and active scanning on 11a DFS frequencies
The wl1271 does not support radar detection. Hence, prevent ad-hoc and
active scanning on frequencies requiring DFS.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:11 +02:00
Gery Kahn
91433029e4 wl1271: cleanup unused code of calibration structures
The cleanup unused code for calibration procedures.

Signed-off-by: Gery Kahn <geryk@ti.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:10 +02:00
Shahar Levi
00d201001b wl1271: Change wl12xx Files Names
All files name prefix removed due to the fact that wl12xx driver supports
wl1271 and wl1273.
Also the definition in Kconfig and header files changed respectively.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-22 16:45:09 +02:00
Felix Fietkau
aaa13ca242 ath9k_hw: support reading calibration data from flash on AR9003
Embedded boards do not have compressed EEPROM data, they use the
struct ar9003_eeprom layout, with little endian fields, so copying
the raw data to the eeprom buffer is enough.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 14:22:24 -05:00
Felix Fietkau
a05b5d4504 ath9k: add support for reading eeprom from platform data on PCI devices
Some embedded boards store platform data for connected PCIe AR92xx
chips in the system flash instead of a separate EEPROM chip.

Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 14:22:23 -05:00
John W. Linville
458fafdd57 rndis_wlan: avoid uninitialized var warning in rndis_wlan_craft_connected_bss
CC [M]  drivers/net/wireless/rndis_wlan.o
drivers/net/wireless/rndis_wlan.c: In function ‘rndis_wlan_craft_connected_bss’:
drivers/net/wireless/rndis_wlan.c:2542:2: warning: ‘ret’ may be used uninitialized in this function

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
2010-11-18 14:22:22 -05:00
John W. Linville
8befba6f22 iwmc3200wifi: clarify potentially undefined operation in iwm_scan_ssids
CC [M]  drivers/net/wireless/iwmc3200wifi/commands.o
drivers/net/wireless/iwmc3200wifi/commands.c: In function ‘iwm_scan_ssids’:
drivers/net/wireless/iwmc3200wifi/commands.c:911:15: warning: operation on ‘iwm->scan_id’ may be undefined

Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 14:22:21 -05:00
Bruno Randolf
eef39befaa ath5k: Use generic EWMA library
Remove ath5k's private moving average implementation in favour of the generic
library version.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 14:22:19 -05:00
Rajkumar Manoharan
3bf30b56c4 ath9k_htc: Avoid setting QoS control for non-QoS frames
Setting tid information in the TX header is required only for QoS
frames. Not handling this case causes severe data loss with some APs.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-18 13:17:47 -05:00
Felix Fietkau
488f6ba75b ath9k_hw: add support for reading EEPROM data from the internal OTP ROM
Some of the new AR9003 cards do not come with an external EEPROM chip
anymore. Calibration data on these cards is stored in the OTP ROM on
the chip.
This patch adds support for reading this data, and also adds support
for different EEPROM chip sizes (512 bytes instead of 1K).

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:30 -05:00
Felix Fietkau
2d42efc44e ath9k: store frame information used by aggregation inside the skb tx info
Since the pointers after the rates in the tx info cannot be used anymore
after frames have been queued, this area can be used to store information
that was previously stored in the ath_buf. With these changes, we can delay
the ath_buf assignment in the aggregation code until aggregates are formed.

That will not only make it possible to simplify DMA descriptor setup to
do less rewriting of uncached memory, but will also make it easier to
move aggregation out of the core of the ath9k tx path.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:29 -05:00
Felix Fietkau
04caf86375 ath9k: more tx setup cleanups
- remove the BUF_HT flag, and instead check for IEEE80211_TX_CTL_AMPDU
  before calling ath_tx_send_ampdu.
- remove a few unused variables
- calculate frame length before adding the frame padding
- merge the misnamed ath_tx_start_dma function into ath_tx_start
- remove an unused argument for assign_aggr_tid_seqno

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:27 -05:00
Felix Fietkau
71a3bf3e94 ath9k: block new AMPDU sessions if SC_OP_TXAGGR is not set
This makes further tx path cleanups easier

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:25 -05:00
Felix Fietkau
28d1670862 ath9k: clean up code duplication around ath_tx_start
Merge initial processing for the CAB queue and regular tx.
Also move ath_tx_cabq() to beacon.c and make it static.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:23 -05:00
Felix Fietkau
c599261825 ath9k: remove bf_tx_aborted from struct ath_buf
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:21 -05:00
Felix Fietkau
76e4522177 ath9k: remove bfs_frmlen from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:19 -05:00
Felix Fietkau
b572d0335f ath9k: remove bfs_nframes from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:18 -05:00
Felix Fietkau
269c44bc84 ath9k: remove bfs_al from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:16 -05:00
Felix Fietkau
3017047f56 ath9k: remove bfs_keyix from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:14 -05:00
Felix Fietkau
82259b77f6 ath9k: remove bfs_paprd_timestamp from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:12 -05:00
Felix Fietkau
952cd69371 ath9k: remove bfs_keytype from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:09 -05:00
Felix Fietkau
5daefbd061 ath9k: remove bfs_tidno from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:07 -05:00
Felix Fietkau
2d3bcba082 ath9k: remove bfs_seqno from struct ath_buf_state
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:05 -05:00
Felix Fietkau
9a6b827063 ath9k: fix PA predistortion training frame setup
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:03 -05:00
Felix Fietkau
c5d0855acf ath9k_hw: set default values for radar pulse detection
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:19:01 -05:00
RA-Jay Hung
387e688464 rt2x00: Modify rt2x00queue_remove_l2pad to make skb->data two-byte alignment
When send out skb data to mac80211, orignal code will cause mac80211
unaligned access, so modify code to make mac80211 can natural access.

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:59 -05:00
RA-Jay Hung
f8eaec659f rt2x00: Fix header_length in rt2x00lib_txdone
Put the assignment of header_length after pull out extra tx headroom

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:57 -05:00
RA-Jay Hung
b43d63bd69 rt2x00: Fix rt2800 USB TX Path DMA issue
rt2800usb chips need to add 1~3 bytes zero padding after each 802.11 header & payload,
and at the end need to add 4 bytes zero padding whether doing TX bulk aggregation or not,

TXINFO_W0_USB_DMA_TX_PKT_LEN in TXINFO must include 1-3 bytes padding after 802.11 header & payload
but do not include 4 bytes end zero padding.

In rt2800usb_get_tx_data_len do not consider multiple of the USB packet size case, sometimes this will
cause USB DMA problem.

Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:55 -05:00
Gertjan van Wingerde
ef8397cfb3 rt2x00: Use ioremap for SoC devices instead of KSEG1ADDR.
Make the code a bit more portable to architectures that do not support
KSEG1ADDR.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Tested-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:54 -05:00
Gertjan van Wingerde
72c7296e03 rt2x00: Remove unneccessary internal Kconfig symbols.
CONFIG_RT2800PCI_PCI and CONFIG_RT2800PCI_SOC are strictly not needed
as we can check the dependent symbols directly in the rest of Kconfig
and the code, so clean up the Kconfig namespace a bit.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:51 -05:00
Gertjan van Wingerde
a6a8d66eba rt2x00: Remove RT30XX Kconfig variables.
Enabling of RT30xx devices via Kconfig variables was introduced when these
devices weren't properly supported yet.
Now that that they are properly supported and functional, we can remove these
Kconfig variables for RT30xx devices and simply enable them whenever rt2800pci
and/or rt2800usb is enabled.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:50 -05:00
Gertjan van Wingerde
46af584d2e rt2x00: Clean up Kconfig for RT2800 devices.
General clean up of the Kconfig part for RT28XX devices.
Also remove the indications of non functional support for rt27xx/rt28xx/rt30xx
devices, as this is no longer true. They just work fine.
Finally, remove the experimental indications for rt27xx/rt28xx/rt30xx devices
as that is no longer true. Keep the experimental indications for rt33xx/rt35xx
devices, though.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:48 -05:00
Gertjan van Wingerde
f93bc9b3ce rt2x00: Add initial support for RT3370/RT3390 devices.
Modified from Eddy's patch by adding the RT3370 USB support as well.

Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Eddy Tsai <Eddy_Tsai@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:47 -05:00
Ivo van Doorn
ae4ecb9f8f rt2x00: Increase REGISTER_BUSY_COUNT
For some hardware the REGISTER_BUSY_COUNT isn't sufficient,
increase the REGISTER_BUSY_COUNT to 100 to catch most
devices which have more problems with accessing the registers.

For normal operating devices nothing would change as they will
exit the loop early anyway.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-17 16:18:45 -05:00
Mohammed Shafi Shajakhan
28d9cc7f21 ath9k_htc: Use macro for caldata array size
The calibration data variable size is based on the number of
channels available in the ath9k driver.

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:39:09 -05:00
Stanislaw Gruszka
ef1b21f7eb iwlwifi: kill elapsed_jiffies
Subtract of jiffies is fine even if one variable overwrap.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:39:09 -05:00
Stanislaw Gruszka
70f3876f09 iwlagn: simplify iwlagn_tx_skb
We can simplify length calculation in iwlagn_tx_skb, that function
is enough complex, without fuzz it more than necessary.

Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:39:09 -05:00
Stanislaw Gruszka
2cb7865648 iwl3945: remove unused len_org variable
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:39:09 -05:00
Felix Fietkau
4e8c14e958 ath9k_hw: add a private op for configuring radar pulse detection
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:08 -05:00
Felix Fietkau
82b873afe8 ath9k: clean up tx buffer setup
Merge ath_tx_send_normal and ath_tx_send_ht_normal.
Move the paprd state initialization and sequence number assignment
to reduce the number of redundant checks.

This not only simplifies buffer allocation error handling, but also
removes a small inconsistency in the buffer HT flag.
This flag should only be set if the frame is also a QoS data frame.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:08 -05:00
Felix Fietkau
61117f01e7 ath9k: remove the tx info padding byte abuse
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Felix Fietkau
f0c255a07f ath9k: handle tx underrun in the driver instead of rate control
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Felix Fietkau
1d666d8e05 ath9k: remove the unnecessary private xretry tx flag
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Ben Greear
7afbb2f070 ath5k: Cleanup opmode setting logic.
An earlier review suggested moving the code in a small
method that was only called once inline.  This patch
accomplishes that.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Senthil Balasubramanian
6ee63f55c7 ath9k_hw: Fix low throughput issue with AR93xx
TX underruns were noticed when RTS/CTS preceded aggregates.
This issue was noticed in ar93xx family of chipsets only.
The workaround involves padding the RTS or CTS length up
to the min packet length of 256 bytes required by the
hardware by adding delimiters to the fist descriptor of
the aggregate.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Vasanthakumar Thiagarajan
39ec2997c3 ath9k: Fix bug in delimiter padding computation
There is a roundng error in delimiter padding computation
which causes severe throughput drop with some of AR9003.

signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc:stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:07 -05:00
Vasanthakumar Thiagarajan
bc2068020b ath9k_hw: Add helper function for interpolation
Also round off interpolated values this would improve power
accuracy by 0.5dB in some cases.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Vasanthakumar Thiagarajan
15cbbc44cc ath9k_hw: Improve power control accuracy for AR9003
It is done for 5Ghz by adding three temperature slopes.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Vasanthakumar Thiagarajan
f4475a6e52 ath9k_hw: Enable strong signal detection for AR9003
Attenuation from eeprom is configured into attenuator control
register.

Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Vasanthakumar Thiagarajan
52a0e2477d ath9k_hw: Fix XPABIAS level configuration for AR9003
Improper configuration of 0x16288 and 0x16290 would affect transmission.

Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Senthil Balasubramanian
3092354970 ath9k_hw: add eeprom templates for ar9003 family chipsets
We are currently using the default eeprom default and it doesn't
work properly for all ar9003 family chipsets. So add eeprom
templates for different versisons and select the eeprom table
based on the template version programmed in the eeprom.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Senthil Balasubramanian
3ceb801bff ath9k_hw: Fix paprd training frame failure.
paprd training frame fails in some rates. Fix the rate mask.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Senthil Balasubramanian
ef5a6a7573 ath9k_hw: Initialize 2GHz CTL properly.
The last 2GHz CTL was not being initialized, so power was being
set to 0 instead of 30dbm. Initialize to 30 like other CTLs.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:06 -05:00
Senthil Balasubramanian
b3dd6bc1f0 ath9k_hw: Add new member into the eeprom structure.
Add eeprom base extension structures which are needed for
AR938x caliberation changes and gain calculation.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:05 -05:00
Senthil Balasubramanian
a9d85fbd3e ath9k_hw: Fix a reset failure on AR9382 (2x2).
AR9382 needs to be configured for the correct chain mask before
running AGC/TxIQ caliberation. Otherwise reset would fail.

Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:05 -05:00
Bruno Randolf
72a801103f ath5k: Add support for antenna configuration
Support setting the antenna configuration via cfg/mac80211. At the moment only
allow the simple pre-defined configurations we already have (fixed antenna A/B
or diversity), but more advanced settings are possible to implement.

Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:05 -05:00
Joe Perches
0e67d6cb75 drivers/net/wireless/b43legacy/main.c: Use printf extension %pV
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:05 -05:00
Joe Perches
5b736d42bc drivers/net/wireless/b43/main.c: Use printf extension %pV
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:04 -05:00
Joe Perches
7e559ec31c drivers/net/wireless/ath/debug.c: Use printf extension %pV
Using %pV reduces the number of printk calls and
eliminates any possible message interleaving from
other printk calls.

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:04 -05:00
Jussi Kivilinna
5cb56af29b rndis_wlan: workaround poor scanning with BCM4320a
BCM4320a devices seem to sometimes do scanning pretty poorly. This can be
workaround by issuing new scan every second, while not yet connected. By this
new scanning method device catches beacons much faster. Fixes bug #20822.

Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:04 -05:00
Jussi Kivilinna
b5257c952d rndis_wlan: workaround device not returning bss for currently connected AP
BCM4320a devices do not return bss for currently connected AP in bss-list,
althought this is required by NDIS specs. Missing bss leads to warning at
net/wireless/sme.c:__cfg80211_connect_result(), WARN_ON(!bss).

Workaround this by crafting bss manually with information we can read from
device. Workaround is only used when device bss-list does not return current
bss, and so is only used with BCM4320a devices and not newer BCM4320b ones.

Fixes bug #20152.

Reported-by: Luís Picciochi <Pitxyoki@gmail.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:04 -05:00
Brian Cavagnolo
d1f9e41d1d mwl8k: use const struct fw pointers throughout
This eliminates compiler warnings by doing things how the
firmware class expects.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:03 -05:00
Brian Cavagnolo
9902047100 mwl8k: make initial firmware load asynchronous
Introduce a firmware loading state machine to manage the process
of loading firmware asynchronously and completing initialization
upon success.  The state machine attempts to load the preferred
firmware image.  If that fails, and if an alternative firmware
image is available, it will attempt to load that one.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:03 -05:00
Brian Cavagnolo
952a0e963f mwl8k: add API version checking for AP firmware
The AP firmware specifies an API version in the GET_HW_SPEC
command response.  Currently, the driver only supports AP
firmware for the 8366, and only supports API v1.  In the future,
if higher API version firmwares emerge (possibly for different
chips), different ops can be selected based on the reported API
version.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:03 -05:00
Brian Cavagnolo
0863ade8d6 mwl8k: choose proper firmware image as directed by user
The mwl8k can operate in AP or STA mode, depending on the
firmware image that is loaded.  By default, STA firmware is
loaded.  Allow the user to override this default mode at
module load time.  This saves an unnecessary firmware reload
for users only interested in AP mode.

Also, the firmware image can be swapped to meet the user's
add_interface request.  For example, suppose the STA
firmware is loaded, no STA interface has been added, and the
user adds an AP interface.  In this case, the AP firmware
will be loaded to meet the request.

Based on contributions from Pradeep Nemavat <pnemavat@marvell.com>,
Yogesh Powar <yogeshp@marvell.com>, and
Lennert Buytenhek <buytenh@wantstofly.org>.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:03 -05:00
Brian Cavagnolo
3cc7772c0a mwl8k: factor out firmware loading and hw init code
This is in preparation for supporting different fw images for
different interface types, and for supporting asynchronous
firmware loading.

Based on a patch from Pradeep Nemavat <pnemavat@marvell.com>
and Yogesh Powar <yogeshp@marvell.com>

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:02 -05:00
Nishant Sarmukadam
41fdf0974d mwl8k: rf_tx_power cmd not supported by AP firmware APIv1
APIv1 AP firmware does not support the RF_TX_POWER command.  It
supports the similar TX_POWER command.

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:02 -05:00
Brian Cavagnolo
a1fe24b0fd mwl8k: revert unnecessary modification of tx descriptor
This reverts change 783391c443728febc669e40597193308460e7b4f.
The stabilized AP v1 firmware uses the same tx descriptor as
the STA firmware.

Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:02 -05:00
Deepak Saxena
ae63a33ec9 libertas: EHS_REMOVE_WAKEUP is not always supported
Certain firmware versions, particularly the 8388 found on the XO-1,
do not support the EHS_REMOVE_WAKEUP command that is used to disable
WOL. Sending this command to the card will return a failure that
would get propagated up the stack and cause suspend to fail.

Instead, fall back to an all-zero wakeup mask.

This fixes http://dev.laptop.org/ticket/9967

Signed-off-by: Deepak Saxena <dsaxena@laptop.org>
Signed-off-by: Daniel Drake <dsd@laptop.org>
[includes fixups by Paul Fox]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:02 -05:00
Daniel Drake
cf43298864 libertas: don't block usb8388 suspend if no wakeup conditions are set
This hunk added by commit 66fceb69b7 seems erroneous. We don't want to
prevent suspend of the whole system if no wakeup params are set.

In the case of the usb8388 we do want to keep the card powered up even
if there are no wakeup params. This is because it will continue acting
as a mesh node.

If the mesh is disabled, it would indeed make more sense to power down
the card during suspend, as the equivalent hunk does for the SD interface.
But that's a separate task; for now just restore the previous behaviour.

Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 16:37:02 -05:00
Rajkumar Manoharan
b5261cf4f3 ath9k_hw: Set proper eeprom offset for AR9287 HTC devices
AR9287 based PCI & USB devices are differed in eeprom start offset.
So set proper the offset for HTC devices to read nvram correctly.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 15:59:39 -05:00
Rajkumar Manoharan
7cbf2611da ath9k_htc: Add new devices into AR7010
Treat new PIDs (0xA704, 0x1200) as AR7010 devices.

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 15:59:39 -05:00
Rajkumar Manoharan
32b089558c ath9k_htc: Update usb device ID list
Added new VID/PIDs into supported devices list

Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 15:59:38 -05:00
Vivek Natarajan
e8364bb8d0 ath9k: Remove pm_qos request after hw unregister.
Update pm_qos before removing it in deinit_device to prevent this
warning:

pm_qos_update_request() called for unknown object.

Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-16 15:59:38 -05:00
Wey-Yi Guy
9e2e7422d0 iwlwifi: set STATUS_READY before commit_rxon
Have the STATUS_READY bit set before commit_rxon call to avoid fail
to send tx power to uCode.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:47:35 -08:00
Shanyu Zhao
6163a3735a iwlagn: check change before commit RXON cmd
When setting rxon chain and filter, no need to commit RXON when the
chain flag is not changed. This reduces the number of RXON commands
we send down to uCode.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:47:22 -08:00
Wey-Yi Guy
21a5b3c6b1 iwlagn: use SKU information in the EEPROM
EEPROM contain the SKU information for the device, use it.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:47:10 -08:00
Shanyu Zhao
f4115d4659 iwlagn: update QoS before commit associated RXON
RXON command without association bit can clear the QoS info in the
uCode. Therefore, before sending the associated RXON, we need to
send the QoS command just in case.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:58 -08:00
Johannes Berg
efe54db823 iwlagn: fix PAN slot timing wrt. DTIM
When the DTIM is not 1, then the slot timing is in
some cases required to be calclulated based on the
DTIM interval instead of the beacon interval, fix
that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:49 -08:00
Johannes Berg
2b5f7a679c iwlagn: reprogram AP STA after assoc
Instead of unconditionally sending unassoc RXON,
before any assoc RXON, re-send only the AP STA
entry which is required after the BSSID has been
programmed into the device to set up internal
filters in the microcode properly.

This fixes some issues that we correlated with
sending a lot of RXON commands to the device.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:35 -08:00
Johannes Berg
893654de3f iwlagn: avoid crash if vif is not assigned
For reasons that aren't entirely clear to me,
we sometimes get here during hardware reset
without the interface being set. Don't crash,
but keep a warning.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:26 -08:00
Johannes Berg
cfa1da7e91 iwlagn: fix PAN queues
Currently, when a PAN queue needs to be
stopped, we erroneously stop queue number 5
(for example) with mac80211 -- which doesn't
even exist!

To avoid that problem, recalculate the swq_id
for all queues when setting up the queues,
and don't use the default identity mapping
that is acceptable for devices which don't
support PAN.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:18 -08:00
Johannes Berg
ea9b307f8e iwlwifi: always build swq_id as virtual queue ID
Previously, we used the swq_id's mechanism
to have AC and HW queue different only for
aggregation queues. To be able to fix a bug
with iPAN simply always build the swq_id as
ac | (hwq << 2) and remove the flag bit.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:46:00 -08:00
Johannes Berg
549a04e092 iwlwifi: pass txq to wake/stop queue
Instead of passing the txq->swq_id, pass the
txq struct directly to make sure that in the
future nobody will pass an invalid number.
Only three places actually change from using
the txq_id or the skb's queue_mapping to now
using txq->swq_id as well.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:45:49 -08:00
Johannes Berg
4bea9b9902 iwlagn: remove a bogus AGG_OFF check
Even if this check were to happen, using the
txq_id here (which is a HW queue) would lead
to confusion in mac80211. Luckily, it doesn't
seem like this can ever happen.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:45:35 -08:00
Johannes Berg
8d56396ac3 iwlagn: remove unused variable swq_id
Simply remove the unused variable swq_id.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:57 -08:00
Johannes Berg
76f379cec6 iwlagn: fix some naming regarding FIFOs
Some variables are misnamed in the FIFO setup
code, fix that.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:41 -08:00
Wey-Yi Guy
564b344c10 iwlwifi: change default led mode for different devices
Set the default led mode for different devices.

For the newer devices such as 6000g2a, 6000g2b and newer,
the default led mode is On/Off instead of blinking.

The led_mode still can be control through module parameter
  0: system default
  1: On/Off
  2: blinking

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:24 -08:00
Wey-Yi Guy
05433df23c iwlagn: change default ACK/CTS MASK setting for WiFi/BT coex
Change the default BT_KILL_ACK_MASK and BT_KILL_CTS_MASK for BT coex

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:10 -08:00
Wey-Yi Guy
66e863a527 iwlagn: support dynamic aggregation for BT coex
Use dynamic aggregation threshold if bt traffic load is high
to reduce the impact on aggregated frame.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:44:00 -08:00
Wey-Yi Guy
95a5ede3ee iwlagn: set dynamic aggregation threshold for BT
Setting the max/min/def value for BT dynamic aggregation threshold.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:43:52 -08:00
Wey-Yi Guy
8829c9e2ec iwlagn: used frame count info in compressed ba packet
For newer devices, uCode provide both "number of frames sent"
and "number of frames acked" information inside the compressed_ba
packet. So instead of figure the success/failure information through
the bitmap, use those information which is much betrer approach.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-16 07:43:42 -08:00
Christian Lamparter
dfa31fef5d carl9170: fix usb anchor wait timeout
usb_wait_anchor_empty_timeout's @timeout
wants milliseconds and not jiffies.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 15:03:13 -05:00
Christian Lamparter
b1d771ee33 carl9170: use generic sign_extend32
This patch replaces the handcrafted
sign extension cruft with a generic
bitop function.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:05 -05:00
Andreas Herrmann
7919a57bc6 bitops: Provide generic sign_extend32 function
This patch moves code out from wireless drivers where two different
functions are defined in three code locations for the same purpose and
provides a common function to sign extend a 32-bit value.

Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:04 -05:00
Grazvydas Ignotas
e4b3fdb800 wl1251: use wl12xx_platform_data to pass data
Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:02 -05:00
Grazvydas Ignotas
1d4b89f297 wl1251: add runtime PM support for SDIO
Add runtime PM support, similar to how it's done for wl1271.
This allows to power down the card when the driver is loaded but
network is not in use.

Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:01 -05:00
Grazvydas Ignotas
cb7bbc7a55 wl1251: add power callback to wl1251_if_operations
Call interface specific power callback before calling board specific
one. Also allow that callback to fail. This is how it's done for
wl1271 and will be used for runtime_pm support.

Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:27:00 -05:00
Wey-Yi Guy
f81c1f4838 iwlagn: enable shadow register
For 6000 series devices and up, enable automatic update MAC's register
for better power usage in PSP mode

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:59 -05:00
Shanyu Zhao
6fe8efb221 iwlwifi: disable disconnected antenna for advanced bt coex
Disconnected antenna algorithm is used to find out which antennas are
disconnected. It should be disabled for devices that support advanced
bluetooth coexist.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:57 -05:00
Shanyu Zhao
3031242b31 iwlwifi: seperate disconnected antenna function
Disconnected antenna algorithm is seperated into its own function from chain noise
calibration routine for better code management.

Signed-off-by: Shanyu Zhao <shanyu.zhao@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:56 -05:00
Johannes Berg
b2769b84d8 iwlagn: fix RXON HT
When the HT information is changed due to
BSS changes (like legacy stations joining)
we need to recalculate HT RXON parameters.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:55 -05:00
Johannes Berg
8da8e62851 iwlagn: re-enable calibration
During the RXON rewrite, this code got lost.
When we've just associated, we need to enable
all calibrations and see if some were already
finished. Add back the missing code.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:53 -05:00
Johannes Berg
52d980c013 iwlagn: fix RXON issues
The RXON rework resulted in a massive loss of
throughput because we weren't programming the
device completely correctly -- the BSSID has
to be programmed into the device before the
AP station is uploaded. To fix this, simply
always send the unassoc RXON, i.e. even when
it was already unassoc so that the BSSID and
some other parameters are updated properly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:52 -05:00
Johannes Berg
2e1fea43aa iwlagn: fix needed chains calculation
Garen noticed that this was wrong. Fix
the calibration -- default to multiple
chains and fall back to single where
possible.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:51 -05:00
Wey-Yi Guy
35a6eb3652 iwlwifi: resending QoS command when HT changes
"mac80211: Fix WMM driver queue configuration"
inadvertedly broke iwlwifi, because now mac80211
configures the QoS settings before assoc, and
therefore before HT. Thus, iwlwifi no longer told
the device about the HT setting, which it needs
to -- and thus throughput went down a lot. Fix
this by resending the QoS command to the device
not only when QoS/WMM settings change, but also
when HT changes.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:49 -05:00
Winkler, Tomas
fd11743dd2 iwlwlifi: update rx write pointer w/o request mac access in the CAM mode
In iwl_rx_queue_update_write_ptr function
replace iwl_write_direct32 with iwl_write32 when not in power save mode.
We don't have to go through grab nic access as the NIC is already awake.

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:48 -05:00
Wey-Yi Guy
708068db4c iwlwifi: legacy tx_cmd_protection function
Legacy (4965 and 3945) devices has different tx_cmd_protection routine.
Move to iwl-legacy.c

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:47 -05:00
Wey-Yi Guy
e39fdee1d7 iwlwifi: put all the isr related function under ops
There were two type of isr supported by iwlwifi devices.
  legacy isr - only used by legacy devices (3945 & 4965)
  ict isr - used by all new generation of iwlwifi devices

Move all the isr related functions into ops, the ict type of isr
supports only needed for newer devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:45 -05:00
Wey-Yi Guy
81baf6ec9c iwlwifi: Legacy isr only used by legacy devices
Move iwl_isr_legacy function to iwl_legacy.c since it only used
by legacy devices.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:44 -05:00
Johannes Berg
ae79d23d0b iwlagn: fix non-5000+ build
When building 4965 without 5000+ there were a
lot of build errors due to functions being used
that weren't even compiled in. To fix this move
some code around and only compile the HCMD code
for 5000+ series as it's not used for 4965.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:43 -05:00
Wey-Yi Guy
2a21ff446c iwlagn: update PCI ID for 100 series devices
Update the supported PCI ID list for 100 series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:41 -05:00
Wey-Yi Guy
fb30eaf387 iwlagn: update PCI ID for 6000g2a series devices
Update the supported PCI ID list for 6000g2a series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:40 -05:00
Wey-Yi Guy
8b37d9f0a1 iwlagn: update PCI ID for 6000g2b series devices
Update the supported PCI ID list for 6000g2b series devices

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:39 -05:00
Ben Greear
5d882c97e2 ath5k: Print stats as unsigned ints.
The debugfs code for ath5k was printing some unsigned int
stats with %d instead of %u.  This meant that you could see
negative numbers instead of a clean wrap.

Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:37 -05:00
Ivo van Doorn
8c5765fda4 rt2x00: Add watchdog functions for HW queue
Add watchdog functions for managing the Queues inside the hardware.
Normally the driver doesn't have much to do with these queues
directly, but the Ralink drivers did implement watchdog functions
for these. These watchdog functions are not triggered that often,
compared to the other watchdog functions, but I have at least
seen them trigger once or twice during a long stresstest run.

v2: Add extra documentation for register fields

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:36 -05:00
Ivo van Doorn
ea175ee262 rt2x00: Remove rt2x00lib_toggle_rx
As part of the queue refactoring, the rt2x00lib_toggle_rx
can be removed and replaced with the call directly to
the set_device_state callback function.

We can remove the STATE_RADIO_RX_ON_LINK and
STATE_RADIO_RX_OFF_LINK, as it was only used for
special behavior inside rt2x00lib rather then the
drivers.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:35 -05:00
Ivo van Doorn
8be4eed0ea rt2x00: Fix rt2x00queue_kick_tx_queue arguments
The queue_entry argument to rt2x00queue_kick_tx_queue,
doesn't make sense due to the function name (it is called
kick QUEUE)... But neither do we need the queue_entry, since
we need the data_queue.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:33 -05:00
Ivo van Doorn
813f0339dd rt2x00: Rename queue->lock to queue->index_lock
The queue->lock is only used to protect the index
numbers. Rename the lock accordingly.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:32 -05:00
Mark Einon
821cde63b5 rt2x00: checkpatch.pl error fixes for rt73usb.c
rt73usb.c:43: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:31 -05:00
Mark Einon
f8bfbc3179 rt2x00: checkpatch.pl error fixes for rt2x00queue.c
rt2x00queue.c:804: ERROR: space prohibited after that open parenthesis '('
rt2x00queue.c:805: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:29 -05:00
Mark Einon
027e8fd105 rt2x00: checkpatch.pl error fixes for rt2x00link.c
rt2x00link.c:70: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:28 -05:00
Mark Einon
5f181dc16b rt2x00: checkpatch.pl error fixes for rt2x00lib.h
rt2x00lib.h:60: ERROR: space prohibited after that open parenthesis '('
rt2x00lib.h:60: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:27 -05:00
Mark Einon
c2361baec1 rt2x00: checkpatch.pl error fixes for rt2x00dev.c
rt2x00dev.c:689: ERROR: spaces required around that '=' (ctx:WxV)

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:25 -05:00
Mark Einon
8a239033c3 rt2x00: checkpatch.pl error fixes for rt2x00config.c
rt2x00config.c:136: ERROR: space required before the open parenthesis '('

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:24 -05:00
Mark Einon
87a46caf92 rt2x00: checkpatch.pl error fixes for rt2800usb.h
rt2800usb.h:43: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:43: ERROR: space prohibited before that close parenthesis ')'
rt2800usb.h:44: ERROR: space prohibited after that open parenthesis '('
rt2800usb.h:44: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:23 -05:00
Mark Einon
144b80bc05 rt2x00: checkpatch.pl error fixes for rt2800usb.c
rt2800usb.c:48: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:21 -05:00
Mark Einon
c6cbadeb3a rt2x00: checkpatch.pl error fixes for rt2800pci.h
rt2800pci.h:41: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:42: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:43: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:44: ERROR: Macros with complex values should be enclosed in parenthesis
rt2800pci.h:55: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:55: ERROR: space prohibited before that close parenthesis ')'
rt2800pci.h:56: ERROR: space prohibited after that open parenthesis '('
rt2800pci.h:56: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:20 -05:00
Mark Einon
bf1b15125e rt2x00: checkpatch.pl error fixes for rt2800lib.c
rt2800lib.c:831: ERROR: inline keyword should sit between storage class and type

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:19 -05:00
Mark Einon
fd8dab9a67 rt2x00: checkpatch.pl error fixes for rt2800.h
rt2800.h:1511: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1511: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1513: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1513: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1515: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1515: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1517: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1517: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1519: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1519: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1521: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1521: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1661: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1661: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1662: ERROR: space prohibited after that open parenthesis '('
rt2800.h:1662: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:1663: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2013: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2013: ERROR: space prohibited before that close parenthesis ')'
rt2800.h:2014: ERROR: space prohibited after that open parenthesis '('
rt2800.h:2014: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:17 -05:00
Mark Einon
cf553477a4 rt2x00: checkpatch.pl error fixes for rt2500usb.c
rt2500usb.c:42: ERROR: do not initialise statics to 0 or NULL

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:16 -05:00
Mark Einon
cb771b1a5d rt2x00: checkpatch.pl error fixes for rt2500pci.h
rt2500pci.h:1091: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1091: ERROR: space prohibited before that close parenthesis ')'
rt2500pci.h:1092: ERROR: space prohibited after that open parenthesis '('
rt2500pci.h:1092: ERROR: space prohibited before that close parenthesis ')'

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:15 -05:00
Mark Einon
46b9786975 rt2x00: checkpatch.pl error fixes for rt2400pci.h
rt2400pci.h:812: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:812: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:813: ERROR: space prohibited after that open parenthesis '('
rt2400pci.h:813: ERROR: space prohibited before that close parenthesis ')'
rt2400pci.h:950: ERROR: Macros with complex values should be enclosed in parenthesis

Signed-off-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:13 -05:00
Christian Lamparter
041fb8f504 carl9170: tx path review
This patch fixes a few shortcomings in the tx path.

 * move temp. ampdu_[ack]_len out of txinfo->pad.

 * fix WARN_ON from tx.c:line 300 when tx_ampdu_queue
   fails to queue the frame.

 * In tx_prepare, we already have a local pointer
   to the station's ieee80211_sta struct.

 * remove a second !sta check, tx_prepare already takes
   care of that.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:12 -05:00
Lalith Suresh
723fc7af53 rt2x00: Fix comments in rt73usb.h and rt61pci.h
This patch fixes a few comments in rt73usb.h and rt61pci.h.

Signed-off-by: Lalith Suresh <suresh.lalith@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:09 -05:00
Helmut Schaa
fa8b4b22d5 rt2x00: Fix hw crypto in AP mode for some devices
The BSSID register shouldn't be set in AP mode on some older devices (like
rt73usb) as it breaks hw crypto on these. However, rt2800 devices explicitly
need the BSSID register set to the same value as our own MAC address (only
in AP mode).

Hence, don't set the BSSID from rt2x00lib but move it down into rt2800 to
avoid problems on older devices.

This fixes a regression (at least for rt73usb) and avoids a new regression
for rt2800 devices in 2.6.36.

Reported-by: Johannes Stezenbach <js@sig21.net>
Reported-by: Lee <lee-in-berlin@web.de>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:08 -05:00
Ivo van Doorn
070192dd29 rt2x00: Fix crash on USB unplug
By not scheduling the TX/RX completion worker threads
when Radio is disabled, or hardware has been unplugged,
the queues cannot be completely cleaned.

This causes crashes when the hardware has been unplugged while
the radio is still enabled.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:07 -05:00
Ivo van Doorn
303c7d6abf rt2x00: Fix MCU_SLEEP arguments
Legacy driver uses 0xff as the second argument for the MCU_SLEEP
command. It is still unknown what the values actually mean, but
this will at least keep the command in-sync with the original
driver.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:06 -05:00
Ivo van Doorn
f44df18c58 rt2x00: Implement flush callback
Implement a basic flush callback function, which simply loops
over all TX queues and waits until all frames have been transmitted
and the status reports have been gathered.

At this moment we don't support dropping any frames during the
flush, but mac80211 will only send 'false' for this argument anyway,
so this is not important at this time.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:04 -05:00
Ivo van Doorn
aaf886bd21 rt2x00: Remove failsave from rt2x00usb_watchdog_tx_dma
When the TX status handler failed to clear the queue
in rt2x00usb_watchdog_tx_dma() we shouldn't use a failsave
to use the rt2x00usb txdone handler.

If a driver has overriden the txdone handler it must make
sure the txdone handler is capable of cleaning up the queue itself.

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:03 -05:00
Ivo van Doorn
7225ce1ea9 rt2x00: Rename rt2x00queue_timeout
Rename rt2x00queue_timeout to rt2x00queue_status_timeout to
better describe what is actually timing out (note that
we already have a rt2x00queue_dma_timeout).

Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:02 -05:00
Helmut Schaa
e2f8c8752b rt2x00: Optimize rt2x00debug_dump_frame when frame dumping is not active
When rt2x00 is compiled with debugging but frame dumping is currently
not active we can avoid the call to do_gettimeofday. Furthermore,
frame dumping is not the default case, mark it as unlikely.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:26:00 -05:00
Helmut Schaa
2b23cdaa3b rt2x00: Reduce tx descriptor size
The tx descriptor values qid, cw_min, cw_max and aifs are directly
accessible through the tx entry struct. So there's no need to copy
them into the tx descriptor and passing them to the indiviual drivers.
Instead we can just get the correct value from the tx entry.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:59 -05:00
Helmut Schaa
08e5310028 rt2x00: Wait up to one second on rt2800 for WPDMA to be ready
At least some devices need such a long time to inititalize WPDMA. This
only increases the maximum wait time and shouldn't affect devices that
have been working before.

Reported-by: Joshua Smith <jesmith@kaon.com>
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:58 -05:00
Helmut Schaa
efd2f271e4 rt2x00: Sync Tx and RX ring sizes with legacy drivers
All rt2x00 devices used the same Tx and Rx ring size (24 entries) till
now. Newer devices (like rt2800) can however make use of a larger TX and
RX ring due to 11n capabilities (AMPDUs of size 64 for example).

Hence, bring rt2x00 in sync with the legacy drivers and use the same TX
and RX ring sizes. Also remove the global defines RX_ENTRIES, TX_ENTRIES,
BEACON_ENTRIES and ATIM_ENTRIES and use per driver values.

That is 24 entries for rt2400pci, 32 entries for rt2500pci, rt2500usb,
rt61pci and rt73usb and 128 (RX) and 64 (TX) for rt2800pci and rt2800usb.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:56 -05:00
Helmut Schaa
961621abee rt2x00: Add TXOP_CTRL_CFG register definition
Remove the magic value initialisation of the TXOP_CTRL_CFG register by
defining its fields and using them during intialisation. The field
RESERVED_TRUN_EN is referred to as reserved, however it is set to 1 by
the legacy drivers. Hence, do the same.

Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:55 -05:00
Felix Fietkau
066dae93bd ath9k: rework tx queue selection and fix queue stopping/waking
The current ath9k tx queue handling code showed a few issues that could
lead to locking issues, tx stalls due to stopped queues, and maybe even
DMA issues.

The main source of these issues is that in some places the queue is
selected via skb queue mapping in places where this mapping may no
longer be valid. One such place is when data frames are transmitted via
the CAB queue (for powersave buffered frames). This is made even worse
by a lookup WMM AC values from the assigned tx queue (which is
undefined for the CAB queue).

This messed up the pending frame counting, which in turn caused issues
with queues getting stopped, but not woken again.

To fix these issues, this patch removes an unnecessary abstraction
separating a driver internal queue number from the skb queue number
(not to be confused with the hardware queue number).

It seems that this abstraction may have been necessary because of tx
queue preinitialization from the initvals. This patch avoids breakage
here by pushing the software <-> hardware queue mapping to the function
that assigns the tx queues and redefining the WMM AC definitions to
match the numbers used by mac80211 (also affects ath9k_htc).

To ensure consistency wrt. pending frame count tracking, these counters
are moved to the ath_txq struct, updated with the txq lock held, but
only where the tx queue selected by the skb queue map actually matches
the tx queue used by the driver for the frame.

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Björn Smedman <bjorn.smedman@venatech.se>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:54 -05:00
Rafał Miłecki
21e731a1b1 b43legacy: rfkill: use status register based on core revision (not PHY's)
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:52 -05:00
maximilian attems
d94519c1b0 zd1201: Add missing id
The Mandriva patch seems to stem from 2.6.14, so much for their
upstreaming effort.

Didn't find another Linux reference of it, just an omnious
"USB\VID_1044&PID_8004" from GigabyteZD1201U.INF for
Gigabyte GN-WLBZ101 802.11b USB Adapter, which matches the
Mandriva patch comment.

Aboves file also lists an "USB\VID_1044&PID_8006", which I have
kept appart as this "Gigabyte GN-WBZB-M 802.11b USB Adapter"
didn't show up in googling.

Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:51 -05:00
maximilian attems
8cecc90e4a zd1211rw: add 2 missing usb id's
"These USB ID came from Palnex <http://www.planex.co.jp/>
Worked fine." says Mandriva patch for their 2.6.32 and earlier.

Web has evidence for both id's to work, so just add them upstream:
http://www.mail-archive.com/zd1211-devs@lists.sourceforge.net/msg00507.html
http://ubuntuforums.org/showthread.php?t=473046

Signed-off-by: Go Taniguchi <go@turbolinux.co.jp>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:50 -05:00
Herton Ronaldo Krzesinski
daeeb07410 rtl8187: restore anaparam registers after reset with 8187B
Current 8187B initialization misses anaparam registers restore after
8187 reset. This causes ANAPARAM register to stay zeroed out (ANAPARAM2
kept its value on my tests). To avoid this, call rtl8187_set_anaparam
right after chip reset (to be on the safe side, as it makes sure we
restore all ANAPARAM registers).

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:48 -05:00
Herton Ronaldo Krzesinski
998606cfd7 rtl8187: remove uneeded setting of anaparam write
Usually you set RTL818X_CONFIG3_ANAPARAM_WRITE when you are going to
change/write ANAPARAM registers. But in current initialization of
RTL8187B there is a place where ANAPARAM_WRITE bit is set without any
ANAPARAM register being written, without reason, so remove it.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: seno <senada@t-online.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:47 -05:00
Herton Ronaldo Krzesinski
0bf198eb4d rtl8187: consolidate anaparam on/off write sequences
There are repeated calls for anaparam on/off sequence in the code.
Consolidate the common code in rtl8187_set_anaparam and use it where
needed.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:46 -05:00
Herton Ronaldo Krzesinski
fe3326903d rtl8187: don't set RTL818X_CONFIG3_GNT_SELECT flag on 8187B
The GNTSel bit should only concern pci devices by looking at RTL8180
spec, which is not the case of 8187B. Also testing shows that trying to
set this bit fails, a subsequent read from the register after trying to
set it shows that the bit isn't set, seems the hardware ignores it,
which makes sense. This setting was a left over from Realtek sources.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:44 -05:00
Herton Ronaldo Krzesinski
896cae65fc rtl8187: move pll reset at start out of ANAPARAM write
On 8187B start, comment about pll reset, and move it out of ANAPARAM
write sequence, so that code is more readable.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:43 -05:00
Herton Ronaldo Krzesinski
a8ff34e37a rtl8187: avoid redundant write to register FF72 (RFSW_CTRL)
The table with misc register initialization was setting it, and later
on we would set it again with a explicity call to rtl818x_iowrite16_idx.

Remove duplicate initialization from the register table.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:42 -05:00
Herton Ronaldo Krzesinski
60f589145d rtl8187: fix wrong register initialization in 8187B
We were using wrong address for BRSR (Basic Rate Set Register) while
initializing its value, comparing with Realtek sources, for 8187B case.

Also, the same register is initialized in rtl8187b_reg_table, so remove
the duplicate initialization from the table.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:40 -05:00
Herton Ronaldo Krzesinski
f002c25cc1 rtl8187: remove setting of beacon/atim registers from initialization
On 8187B path, we set a initial value for beacon interval and atim
window on initialization. But this isn't needed, since same setup is
done on rtl8187_config.

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:39 -05:00
Herton Ronaldo Krzesinski
327571ea99 rtl8187: remove redundant initialization of ARFR
This removes redundant write to Auto Rate Fallback Register on RTL8187B.
The same value was being written twice in the same function. Avoid this
removing the duplicate initialization on rtl8187b_reg_table, and also
add comment for this write (information from Realtek source).

Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:38 -05:00
Nishant Sarmukadam
c0bf9ca98e mwl8k: force AP mode to use non-AMPDU frames
AP firmware uses xmitcontrol to differentiate between AMPDU
and non-AMPDU frames. As the support for AMPDU is not yet
added, set xmitcontrol to non-AMPDU for all tx frames for AP
firmware. This field will be set to indicate ampdu/non-ampdu
frames when tx AMPDU support is added.

Signed-off-by: Pradeep Nemavat <pnemavat@marvell.com>
Signed-off-by: Brian Cavagnolo <brian@cozybit.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:36 -05:00
Christian Lamparter
3eedb6f436 carl9170: configurable beacon rates
Previously, the beacon rate was fixed to either:
 * 1Mb/s [2.4GHz band]
 * 6Mb/s [5GHz band]

This limitation has been addressed and now the
beacon rate is selected by ieee80211_tx_info's
rate control info, almost like any ordinary
data frame.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:35 -05:00
Christian Lamparter
2a6cef513f carl9170: stop stale uplink BA sessions
This patch fixes a possible lengthy stall if the device
is operating as an experimental 11n AP and an STA
[during heavy txrx action] suddenly signalized to go
off-channel (old NetworkManager), or (sleep - which is
unlikely, because then it wouldn't be *active* at all!?).

Because the driver has to manage the BA Window, the
sudden PSM transition can leave active uplink BA
sessions to the STA in a bad state and a proper
cleanup is needed.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:33 -05:00
Christian Lamparter
e4a668c590 carl9170: fix spurious restart due to high latency
RX Stress tests of unidirectional bulk traffic with
bitrates of up to 220Mbit/s have revealed that the
fatal-event recovery logic [which was solely triggered
by an out-of-rx-buffer situation] is too aggressive.

The new method now "pings" the device and then
decides - based on the response - whenever
a restart is needed or not.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:32 -05:00
Christian Lamparter
e27769059c carl9170: initialize HW aMPDU parameters properly
This patch changes the initial aMPDU density and
factor settings to match those of Otus.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:31 -05:00
Christian Lamparter
3f1240e4f4 carl9170: import hw/fw header updates
This patch imports all shared header changes
from carl9170fw.git.

 * add some strategic __aligned(4).
   This allows the compiler generate optimized code for
   architectures which can't access (unaligned/packed)
   data efficiently.
   ("ath9k_hw: optimize all descriptor access functions")

 * add a forgotten __CARL9170FW__ ifdef around
   a private firmware-internal struct.

 * GET_VAL macro helper
   Very useful for extracting data out of the
   bit-packed PHY registers.

 * cosmetic changes
   e.g.: _CCA_MINCCA_ to just _CCA_MIN_.

 * version bump 1.8.8.3 -> 1.9.0.

Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:29 -05:00
Blaise Gassend
bdd7bd1643 mac80211_hwsim: Incorporate txpower into rssi
Up to now mac80211_hwsim has been reporting an rssi of -50. This patch
improves the model slightly by returning txpower-50. This makes it
easy to stimulate tests that need to see a varying rssi.

Signed-off-by: Blaise Gassend <blaise@willowgarage.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:28 -05:00
Thadeu Lima de Souza Cascardo
19999792d2 rtl8187b: do not do per packet TX AGC
Clearing the per packet TX AGC for the RTL8187B device appears to
increase its overall TX power. This allows the device to associate and a
connection to be established using APs a little further away.

This is in accordance to what is done for RTL8187L devices and also what
Realtek drivers do.

Tested-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Cc: linux-wireless@vger.kernel.org
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Rogerio Luz Coelho <rogluz.news@gmail.com>
Cc: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Hin-Tak Leung <hintak.leung@gmail.com>
Cc: seno <senada@t-online.de>
Tested-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:25:27 -05:00
Eliad Peller
e285a5250c wl1271: add recover testmode command
add RECOVER testmode command.
this command triggers a recovery sequence (by enqueueing a recovery_work).

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:25 -05:00
Eliad Peller
ccc83b046c wl1271: handle HW watchdog interrupt
unmask the WL1271_ACX_INTR_WATCHDOG interrupt.
when getting it - enqueue a recovery work and bail out.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:24 -05:00
Eliad Peller
03107a4b59 wl1271: refactor debugfs function generation code
refactor wl1271_debugfs by using a format&copy function, instead of
duplicating the code for each generated function.

this change reduces about 3Kb from wl1271.ko

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:23 -05:00
Eliad Peller
71125abdf0 wl1271: set wl->vif only if add_interface succeeded.
set wl->vif to the newly created interface only after the firmware booted
successfully. on the way - make the function flow more clear.

Signed-off-by: Eliad Peller <eliad@wizery.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:21 -05:00
Juuso Oikarinen
f8d9802f66 wl1271: Check interface state in op_* functions
Check the state of the interface on op_* function so we don't try to access
the hardware in when its off.

The mac80211 may call these in some corner cases related, for instance, to
the hardware recovery procedure. These accesses cause a kernel crash on at
least some SDIO devices, because the bus is not properly claimed in that
scenario.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:20 -05:00
Juuso Oikarinen
b739a42c92 wl1271: Fix scan failure detection
In scan_complete_work, because the mutex is released before accessing the
scan->failed flag, it is possible for unfounded hardware recovery rounds
to be executed.

Fix this.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:19 -05:00
Juuso Oikarinen
fb2382c75b wl1271: Fix RX path stall
The wl1271_rx function loops through packets in an aggregated buffer. Each
packet in the buffer is handled by a call to wl1271_rx_handle_data, which will
fail if skb memory allocation fails or production mode is enabled. These
failures currently prevent the rx counters to be incremented, thus causing the
rx loop to run forever.

Fix this by ignoring error codes reported wl1271_rx_handle_data function.
This essentially means that frames will be dropped in production mode, which
is the intetion, and frames will be dropped if memory allocation fails, which
is a decent way to recover from that situation.

Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:17 -05:00
Nicolas Kaiser
ff6d76fd3d wireless/wl1271: remove redundant if-statement v2
wl1271_ps_elp_sleep() is void and cannot return a value.

Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:16 -05:00
Luciano Coelho
5404643139 wl1271: exit ELP mode when setting enabled rates in tx
This bug was being triggered by a call to acx_rate_policies in tx_work
without calling ps_elp_wakeup first.  If we have full PSM enabled, this
happens rather often, immediately after association.

Reported-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
2010-11-15 13:25:14 -05:00
Teemu Paasikivi
6a2de93b25 wl1271: Fix warning about unsupported RX rate
While scanning, it is possible that beacon and probe response frames are
received on other band than configured to the driver. In rx status
handling this has caused "Unsupported RX rate from HW" warnings. This
patch changes the wl1271_rate_to_index function to take the band of the
received frame as a parameter instead of using value configuret to
wl->band.

Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:13 -05:00
Shahar Levi
18357850b6 wl1271: 11n Support, functionality and configuration ability
Add 11n ability in scan, connection and using MCS rates.
The configuration is temporary due to the code incomplete and
still in testing process. That plans to be remove in the future.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:12 -05:00
Shahar Levi
c4db1c8796 wl1271: 11n Support, ACX Commands
Added ACX command to the FW for 11n support.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:10 -05:00
Shahar Levi
e8b03a2b8d wl1271: 11n Support, Add Definitions
Two acx commands: ht_capabilities & ht_information, 11n sta capabilities
macro.

Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:09 -05:00
Ido Yariv
2fe33e8cff wl1271: Fix TX queue low watermark handling
The number of entries in the TX queue is compared to the low watermark
value each time TX completion interrupts are handled.
However, the fact that a TX completion arrived does not necessarily mean
there are any less skbs in the TX queue.

In addition, a TX completion interrupt does not necessarily mean that there
are any new available TX blocks. Thus, queuing TX work when the low
watermark is reached might not be needed.

Fix this by moving the low watermark handling to the TX work function,
and avoid queuing TX work in this case.

Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:08 -05:00
Ido Yariv
25eeb9e387 wl1271: Allocate TX descriptors more efficiently
On each TX descriptor allocation, a free entry is found by traversing the TX
descriptors array.

Improve this by holding a bitmap of all TX descriptors, and using efficient
bit operations to search for free entries.

Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:06 -05:00
Ido Yariv
a522550a28 wl1271: Fix TX starvation
While wl1271_irq_work handles RX directly (by calling wl1271_rx), a different
work is scheduled for transmitting packets. The IRQ work might handle more than
one interrupt during a single call, including multiple TX completion
interrupts. This might starve TX, since no packets are transmitted until all
interrupts are handled.

Fix this by calling the TX work function directly, instead of deferring
it.

Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:05 -05:00
Ido Yariv
6c6e669ed6 wl1271: TX aggregation optimization
In case the aggregation buffer is too small to hold all available packets,
the buffer is transferred to the FW and no more packets are aggregated.
Although there may be enough available TX blocks, no additional packets will
be handled by the current TX work.

Fix this by flushing the aggregation buffer when it's full, and continue
transferring packets as long as there are enough available TX blocks.

Signed-off-by: Ido Yariv <ido@wizery.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:03 -05:00
Gery Kahn
c8aea565e8 wl1271: ref_clock cosmetic changes
Cosmetic cleanup for ref_clock code while configured by board.

Signed-off-by: Gery Kahn <geryk@ti.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
2010-11-15 13:25:02 -05:00
Wey-Yi Guy
34d59c07e9 iwlagn: use 6000g2b uCode for 130 series devices
For 130 series device, 6000g2b uCode will be used, no need to
have additional defines for 130 devices, so remove those.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:59 -05:00
Wey-Yi Guy
69d826b6c5 iwlwifi: add new devices to Kconfig
Adding description to Kconfig to indicate more devices
are being supported by iwlagn

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:58 -05:00
Wey-Yi Guy
f5682c01eb iwlagn: turn dynamic smps on while BT is on
While BT is on and doing iscan and/or pscan, BT is in listen
mode which will impact WiFi throughput, we need to
enable dynamic smps in order to improve the rx throughput.

Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:57 -05:00
Johannes Berg
d4daaea656 iwlwifi: implement switching iftype while up
Implement switching the interface while an
interface is up in iwlwifi. Interfaces have
to stay on the context they were created on.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:55 -05:00
Johannes Berg
bd50a8ab9f iwlwifi: fix IBSS beaconing
My previous patch to clean up all RXON handling
inadvertently broke IBSS because it failed to
take into account that unlike in AP mode, IBSS
requires beacons to be sent only after setting
the RXON assoc.

Fix this, clean up the code a bit, improve the
error checking around this, and also react to
beacon changes in IBSS mode from mac80211.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:54 -05:00
Johannes Berg
2295c66b68 iwlagn: new RXON processing for modern devices
In order to simplify the flow, and make new
enhancements easier, separate out the RXON
processing for modern AGN (5000 and newer)
from RXON processing for the older 3945 and
4965 devices. Avoid changing these old ones
to avoid regressions and move their code to
a new file (iwl-legacy.c). 4965 gets the
commit_rxon that used to be common for all
AGN devices, but with removed PAN support.

The new RXON processing is more central and
does more work in committing, so that it is
easier to follow.

To make it more evident what is split out
for legacy, split the necessary operations
for that into a new struct iwl_legacy_ops.
Those parts that still exist in the new AGN
code don't need to be parametrized.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:53 -05:00
Johannes Berg
2d4e43c3c6 iwlagn: don't resend RXON timing
Resending RXON timing here caused issues with
dual-mode under certain circumstances, so avoid
doing it here right now.

This effectively reverts b01efe434b
and partially 2491fa42d9. The next
patch will make all this cleaner for just the
devices that need it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:51 -05:00
Johannes Berg
dc21b54532 iwlwifi: make mac80211 ops a device config
In the future, 4965 and modern AGN devices will
need to have different mac80211 callbacks since
they have different capabilities. Prepare for
that by making the mac80211 operations a device
config.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:50 -05:00
Luis R. Rodriguez
6a6733f256 ath9k: content DMA start / stop through the PCU lock
This helps align resets / RX enable & disable / TX stop / start.
Locking around the PCU is important to ensure the hardware doesn't
get stale data when working with DMA'able data.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Tested-by:  Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:47 -05:00
Luis R. Rodriguez
4bdd1e978e ath9k: move the PCU lock to the sc structure
The PCU lock should be used to contend TX DMA as well,
this will be done next.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Tested-by:  Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:46 -05:00
Luis R. Rodriguez
9d94674ab7 ath9k: simplify hw reset locking
The new PCU lock is better placed so we can just contend
against that when trying to reset hardware.

This is part of a series of patches which fix stopping
TX DMA completley when requested on the driver.
For more details about this issue refer to this thread:

http://marc.info/?l=linux-wireless&m=128629803703756&w=2

Tested-by:  Ben Greear <greearb@candelatech.com>
Cc: Kyungwan Nam <kyungwan.nam@atheros.com>
Cc: stable@kernel.org
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:44 -05:00
Mohammed Shafi Shajakhan
5d4c428254 ath9k: Properly assign boolean types
This takes care that boolean types are properly assigned

Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:43 -05:00
Rajkumar Manoharan
446fad5a5b ath9k_htc: Handle monitor mode properly for HTC devices
No need to inform about monitor interface changes to
firmware. Set the HW mode to monitor type based on mac80211
indication flag is sufficient.

Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-15 13:24:42 -05:00
John W. Linville
f60dc0138a iwlwifi: Convert to new PCI PM framework
Use the new PCI PM and let the PCI core code handle the PCI-specific
details of power transitions.

Based on similarly titled ath9k patch posted by Rafael J. Wysocki.

Signed-off-by: John W. Linville <linville@tuxdriver.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
2010-11-15 13:24:40 -05:00