- Use PCI_VENDOR_ID_AMCC macro instead of defining a custom macro in
pci-xgene.c (Pali Rohár)
* remotes/lorenzo/pci/xgene:
PCI: xgene: Use PCI_VENDOR_ID_AMCC macro
- Assign a number to each VMD controller to distinguish them in
/proc/interrupts (Chunguang Xu)
- Don't disable VMD MSI-X remapping if IOMMU remapping is enabled (Adrian
Huang)
- Add Kconfig dependency on !UML for allyesconfig build issue (Johannes
Berg)
* remotes/lorenzo/pci/vmd:
PCI: vmd: depend on !UML
PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU
PCI: vmd: Assign a number to each VMD controller
- Reorganize to separate out PHY logic (Mauro Carvalho Chehab)
- Add support for external PHY in addition to the internal PHY (Mauro
Carvalho Chehab)
- Use regmap so both kirin driver and PHY can access APB registers (Mauro
Carvalho Chehab)
- Add support for per-lane PERST# GPIOs on HiKey970 external PEX 8606 PCI
bridge (Mauro Carvalho Chehab)
- Add "hisilicon,kirin970-pcie" compatible string (Mauro Carvalho Chehab)
- Add MODULE_* macros (Mauro Carvalho Chehab)
- Allow building as a module (Mauro Carvalho Chehab)
- Add power_off support for Kirin 960 PHY (Mauro Carvalho Chehab)
- Disable clkreq during poweroff sequence (Mauro Carvalho Chehab)
- De-init the dwc driver during remove (Mauro Carvalho Chehab)
- Allow removal of kirin driver (Mauro Carvalho Chehab)
* pci/host/kirin:
PCI: kirin: Allow removing the driver
PCI: kirin: De-init the dwc driver
PCI: kirin: Disable clkreq during poweroff sequence
PCI: kirin: Move the power-off code to a common routine
PCI: kirin: Add power_off support for Kirin 960 PHY
PCI: kirin: Allow building it as a module
PCI: kirin: Add MODULE_* macros
PCI: kirin: Add Kirin 970 compatible
PCI: kirin: Support PERST# GPIOs for HiKey970 external PEX 8606 bridge
PCI: kirin: Use regmap for APB registers
PCI: kirin: Add support for a PHY layer
PCI: kirin: Reorganize the PHY logic inside the driver
- Use sysfs_emit() in "show" functions instead of sprintf() to avoid buffer
overruns (Kunihiko Hayashi)
* remotes/lorenzo/pci/endpoint:
PCI: endpoint: Use sysfs_emit() in "show" functions
- Export dw_pcie_ep_reset_bar(), dw_pcie_link_up() so more drivers can be
modular (Luca Ceresoli)
- Allow dra7xx host and endpoint drivers to be modules (Luca Ceresoli)
- Enable dra7xx optional external clock if present (Luca Ceresoli)
- Clean up Kconfig dependencies for PCIE_DW_HOST- and PCIE_DW_EP-based
drivers (Andy Shevchenko)
- Remove visconti redundant dev_err() after platform_get_irq_byname()
failure (Krzysztof Wilczyński)
- Run dwc .host_init() method before registering MSI interrupt handler so
we have a chance to deal with pending interrupts left by bootloader
(Bjorn Andersson)
- Serialize uniphier INTx masking/unmasking (Kunihiko Hayashi)
* pci/host/dwc:
PCI: uniphier: Serialize INTx masking/unmasking and fix the bit operation
PCI: dwc: Perform host_init() before registering msi
PCI: visconti: Remove surplus dev_err() when using platform_get_irq_byname()
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_EP)
PCI: dwc: Clean up Kconfig dependencies (PCIE_DW_HOST)
PCI: dra7xx: Get an optional clock
PCI: dra7xx: Remove unused include
PCI: dra7xx: Make it a kernel module
PCI: dwc: Export more symbols to allow modular drivers
- Make of_phandle_args_to_fwspec() generally available (Marc Zyngier)
- Allow matching of interrupt-maps local to interrupt controller or PCI
device (Marc Zyngier)
- Add Apple SoC (e.g., M1) PCIe host controller driver, which enables
access to USB type-A, Ethernet, Wi-Fi, Bluetooth devices; these require
additional drivers of their own (Alyssa Rosenzweig)
- Add apple INTx, per-port, and MSI interrupt support (Marc Zyngier)
- Configure apple Requester-ID-to-Stream-ID mapper for IOMMU (DART) support
(Marc Zyngier)
* pci/host/apple:
PCI: apple: Configure RID to SID mapper on device addition
iommu/dart: Exclude MSI doorbell from PCIe device IOVA range
PCI: apple: Implement MSI support
PCI: apple: Add INTx and per-port interrupt support
PCI: apple: Set up reference clocks when probing
PCI: apple: Add initial hardware bring-up
PCI: of: Allow matching of an interrupt-map local to a PCI device
of/irq: Allow matching of an interrupt-map local to an interrupt controller
irqdomain: Make of_phandle_args_to_fwspec() generally available
- Define macros for PCI_EXP_DEVCTL_PAYLOAD_* (Pali Rohár)
- Set Max Payload Size to 512 bytes per Marvell spec (Pali Rohár)
- Downgrade PIO Response Status messages to debug level (Marek Behún)
- Preserve CRS SV (Config Request Retry Software Visibility) bit in
emulated Root Control register (Pali Rohár)
- Fix issue in configuring reference clock (Pali Rohár)
- Don't clear status bits for masked interrupts (Pali Rohár)
- Don't mask unused interrupts (Pali Rohár)
- Avoid code repetition in advk_pcie_rd_conf() (Marek Behún)
- Retry config accesses on CRS response (Pali Rohár)
- Simplify emulated Root Capabilities initialization (Pali Rohár)
- Fix several link training issues (Pali Rohár)
- Fix link-up checking via LTSSM (Pali Rohár)
- Fix reporting of Data Link Layer Link Active (Pali Rohár)
- Fix emulation of W1C bits (Marek Behún)
- Fix MSI domain .alloc() method to return zero on success (Marek Behún)
- Read entire 16-bit MSI vector in MSI handler, not just low 8 bits (Marek
Behún)
- Clear Root Port I/O Space, Memory Space, and Bus Master Enable bits at
startup; PCI core will set those as necessary (Pali Rohár)
- When operating as a Root Port, set class code to "PCI Bridge" instead of
the default "Mass Storage Controller" (Pali Rohár)
- Add emulation for PCI_BRIDGE_CTL_BUS_RESET since aardvark doesn't
implement this per spec (Pali Rohár)
- Add emulation of option ROM BAR since aardvark doesn't implement this per
spec (Pali Rohár)
* remotes/lorenzo/pci/aardvark:
PCI: aardvark: Fix support for PCI_ROM_ADDRESS1 on emulated bridge
PCI: aardvark: Fix support for PCI_BRIDGE_CTL_BUS_RESET on emulated bridge
PCI: aardvark: Set PCI Bridge Class Code to PCI Bridge
PCI: aardvark: Fix support for bus mastering and PCI_COMMAND on emulated bridge
PCI: aardvark: Read all 16-bits from PCIE_MSI_PAYLOAD_REG
PCI: aardvark: Fix return value of MSI domain .alloc() method
PCI: pci-bridge-emul: Fix emulation of W1C bits
PCI: aardvark: Fix reporting Data Link Layer Link Active
PCI: aardvark: Fix checking for link up via LTSSM state
PCI: aardvark: Fix link training
PCI: aardvark: Simplify initialization of rootcap on virtual bridge
PCI: aardvark: Implement re-issuing config requests on CRS response
PCI: aardvark: Deduplicate code in advk_pcie_rd_conf()
PCI: aardvark: Do not unmask unused interrupts
PCI: aardvark: Do not clear status bits of masked interrupts
PCI: aardvark: Fix configuring Reference clock
PCI: aardvark: Fix preserving PCI_EXP_RTCTL_CRSSVE flag on emulated bridge
PCI: aardvark: Don't spam about PIO Response Status
PCI: aardvark: Fix PCIe Max Payload Size setting
PCI: Add PCI_EXP_DEVCTL_PAYLOAD_* macros
- Tidy setup-irq.c comments (Pranay Sanghai)
- Fix misspellings (Krzysztof Wilczyński)
- Fix sprintf(), sscanf() format mismatches (Krzysztof Wilczyński)
- Tidy cpqphp code formatting (Krzysztof Wilczyński)
- Remove unused pci_pool wrappers, which have been replaced by dma_pool
(Cai Huoqing)
- Remove a redundant initialization in __pci_reset_function_locked() (Colin
Ian King)
- Use 'unsigned int' instead of 'unsigned' (Krzysztof Wilczyński)
- Update PCI subsystem information in MAINTAINERS (Krzysztof Wilczyński)
- Include generic <linux/> headers instead of <asm/> for cpqphp and vmd
(Krzysztof Wilczyński)
* pci/misc:
PCI: vmd: Drop redundant includes of <asm/device.h>, <asm/msi.h>
PCI: cpqphp: Use <linux/io.h> instead of <asm/io.h>
MAINTAINERS: Update PCI subsystem information
PCI: Prefer 'unsigned int' over bare 'unsigned'
PCI: Remove redundant 'rc' initialization
PCI: Remove unused pci_pool wrappers
PCI: cpqphp: Format if-statement code block correctly
PCI: Use unsigned to match sscanf("%x") in pci_dev_str_match_path()
PCI: hv: Remove unnecessary use of %hx
PCI: Correct misspelled and remove duplicated words
PCI: Tidy comments
- Add pci_read_vpd_any(), pci_write_vpd_any() to access VPD at arbitrary
offsets (Heiner Kallweit)
- Use VPD API to replace custom code in cxgb3 driver (Heiner Kallweit)
* pci/vpd:
cxgb3: Remove seeprom_write and use VPD API
cxgb3: Use VPD API in t3_seeprom_wp()
cxgb3: Remove t3_seeprom_read and use VPD API
PCI/VPD: Use pci_read_vpd_any() in pci_vpd_size()
PCI/VPD: Add pci_read/write_vpd_any()
- Avoid bus resets on Atheros QCA6174, since they hang (Ingmar Klein)
- Use store and forward mode on Pericom PI7C9X2G switches to avoid ACS
erratum with ACS P2P Request Redirect (Nathan Rossi)
* pci/virtualization:
PCI: Add ACS quirk for Pericom PI7C9X2G switches
PCI: Mark Atheros QCA6174 to avoid bus reset
- Check for CAP_SYS_ADMIN before validating sysfs user input, not after
(Krzysztof Wilczyński)
- Always return -EINVAL from sysfs "store" functions for invalid user input
instead of -EINVAL sometimes and -ERANGE others (Krzysztof Wilczyński)
- Use kstrtobool() directly instead of the strtobool() wrapper (Krzysztof
Wilczyński)
* pci/sysfs:
PCI: Use kstrtobool() directly, sans strtobool() wrapper
PCI/sysfs: Return -EINVAL consistently from "store" functions
PCI/sysfs: Check CAP_SYS_ADMIN before parsing user input
# Conflicts:
# drivers/pci/iov.c
- Return error to application when command execution fails because an
out-of-band reset has cleared the device BARs, Memory Space Enable, etc
(Kelvin Cao)
- Fix MRPC error status handling issue (Kelvin Cao)
- Mask out other bits when reading of management VEP instance ID (Kelvin
Cao)
- Return EOPNOTSUPP instead of ENOTSUPP from sysfs show functions (Kelvin
Cao)
- Add check of event support (Logan Gunthorpe)
* pci/switchtec:
PCI/switchtec: Add check of event support
PCI/switchtec: Replace ENOTSUPP with EOPNOTSUPP
PCI/switchtec: Update the way of getting management VEP instance ID
PCI/switchtec: Fix a MRPC error status handling issue
PCI/switchtec: Error out MRPC execution when MMIO reads fail
- Don't setup portdrv IRQs if there are no port drivers that use them, to
conserve vectors and avoid spurious events (Jan Kiszka)
* pci/portdrv:
PCI/portdrv: Do not setup up IRQs if there are no users
- Apply bus offset correctly in DMA address calculation, which used the
wrong sign before (Wang Lu)
* pci/p2pdma:
PCI/P2PDMA: Apply bus offset correctly in DMA address calculation
- Document sysfs "irq" attribute, which contains either the INTx IRQ (the
intended behavior) or the first MSI IRQ (historical mistake retained for
backwards compatibility) (Barry Song)
- Rework "irq" sysfs show function to explicitly fetch first MSI IRQ
instead of depending on core to put it in dev->irq, to enable future core
cleanup (Barry Song)
* pci/msi:
PCI/sysfs: Explicitly show first MSI IRQ for 'irq'
PCI: Document /sys/bus/pci/devices/.../irq
- Ignore Link Down/Up caused by error-induced Hot Reset so endpoint driver
can remain bound to device during error recovery (Lukas Wunner)
- Remove unused resume err_handler (Lukas Wunner)
- Remove unused pcie_port_bus_{,un}register() declarations (Lukas Wunner)
- Skip compiling err.c when CONFIG_PCIEAER not set (Lukas Wunner)
* pci/hotplug:
PCI/ERR: Reduce compile time for CONFIG_PCIEAER=n
PCI/portdrv: Remove unused pcie_port_bus_{,un}register() declarations
PCI/portdrv: Remove unused resume err_handler
PCI: pciehp: Ignore Link Down/Up caused by error-induced Hot Reset
PCI/portdrv: Rename pm_iter() to pcie_port_device_iter()
- Drop the struct pci_dev.driver pointer, which is redundant with the
struct device.driver pointer (Uwe Kleine-König)
* pci/driver:
PCI: Remove struct pci_dev->driver
PCI: Use to_pci_driver() instead of pci_dev->driver
x86/pci/probe_roms: Use to_pci_driver() instead of pci_dev->driver
perf/x86/intel/uncore: Use to_pci_driver() instead of pci_dev->driver
powerpc/eeh: Use to_pci_driver() instead of pci_dev->driver
usb: xhci: Use to_pci_driver() instead of pci_dev->driver
cxl: Use to_pci_driver() instead of pci_dev->driver
cxl: Factor out common dev->driver expressions
xen/pcifront: Use to_pci_driver() instead of pci_dev->driver
xen/pcifront: Drop pcifront_common_process() tests of pcidev, pdrv
nfp: use dev_driver_string() instead of pci_dev->driver->name
mlxsw: pci: Use dev_driver_string() instead of pci_dev->driver->name
net: marvell: prestera: use dev_driver_string() instead of pci_dev->driver->name
net: hns3: use dev_driver_string() instead of pci_dev->driver->name
crypto: hisilicon - use dev_driver_string() instead of pci_dev->driver->name
powerpc/eeh: Use dev_driver_string() instead of struct pci_dev->driver->name
ssb: Use dev_driver_string() instead of pci_dev->driver->name
bcma: simplify reference to driver name
crypto: qat - simplify adf_enable_aer()
scsi: message: fusion: Remove unused mpt_pci driver .probe() 'id' parameter
PCI/ERR: Factor out common dev->driver expressions
PCI: Drop pci_device_probe() test of !pci_dev->driver
PCI: Drop pci_device_remove() test of pci_dev->driver
PCI: Return NULL for to_pci_driver(NULL)
- Rename pcibios_add_device() to pcibios_device_add() since it's called
from pci_device_add() (Oliver O'Halloran)
- Don't try to enable AtomicOps on VFs, since they can only be enabled on
the PF (Selvin Xavier)
* pci/enumeration:
PCI: Do not enable AtomicOps on VFs
PCI: Rename pcibios_add_device() to pcibios_device_add()
- Re-enable LTR in Downstream Ports after it has been disabled by reset or
hotplug to allow use of ASPM L1.2 again and prevent Unsupported Request
errors when Endpoint sends LTR messages (Mingchuang Qiao)
* pci/aspm:
PCI: Re-enable Downstream Port LTR after reset or hotplug
- Simplify _OSC negotiation with platform for control of PCIe features
(Joerg Roedel)
* pci/acpi:
PCI/ACPI: Check for _OSC support in acpi_pci_osc_control_set()
PCI/ACPI: Move _OSC query checks to separate function
PCI/ACPI: Move supported and control calculations to separate functions
PCI/ACPI: Remove OSC_PCI_SUPPORT_MASKS and OSC_PCI_CONTROL_MASKS
The Pericom PI7C9X2G404/PI7C9X2G304/PI7C9X2G303 PCIe switches have an
erratum for ACS P2P Request Redirect behaviour when used in the cut-through
forwarding mode. The recommended work around for this issue is to use the
switch in store and forward mode. The erratum results in packets being
queued and not being delivered upstream, which can be observed as very poor
downstream device performance and/or dropped device-generated
data/interrupts.
Add a fixup so that when enabling or resuming the downstream port we check
if it has enabled ACS P2P Request Redirect, and if so, change the device
(via the upstream port) to use the store and forward operating mode.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177471
Link: https://lore.kernel.org/r/20210910025823.196508-1-nathan@nathanrossi.com
Tested-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Nathan Rossi <nathan.rossi@digi.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Apple PCIe controller doesn't directly feed the endpoint's Requester ID
to the IOMMU (DART), but instead maps RIDs onto Stream IDs (SIDs). The DART
and the PCIe controller must thus agree on the SIDs that are used for
translation (by using the 'iommu-map' property).
For this purpose, parse the 'iommu-map' property each time a device gets
added, and use the resulting translation to configure the PCIe RID-to-SID
mapper. Similarly, remove the translation if/when the device gets removed.
This is all driven from a bus notifier which gets registered at probe time.
Hopefully this is the only PCI controller driver in the whole system.
[bhelgaas: squash indentation from Zhaoyu Liu <zackary.liu.pro@gmail.com>:
https://lore.kernel.org/r/20211031135544.GA1616@pc]
Link: https://lore.kernel.org/r/20210929163847.2807812-10-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
The MSI doorbell on Apple HW can be any address in the low 4GB range.
However, the MSI write is matched by the PCIe block before hitting the
iommu. It must thus be excluded from the IOVA range that is assigned to any
PCIe device.
Link: https://lore.kernel.org/r/20210929163847.2807812-9-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Probe for the 'msi-ranges' property, and implement the MSI support in the
form of the usual two-level hierarchy.
Note that contrary to the wired interrupts, MSIs are shared among all the
ports.
Link: https://lore.kernel.org/r/20210929163847.2807812-8-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add support for the per-port interrupt controller that deals with both INTx
signalling and management interrupts.
This allows the Link-up/Link-down interrupts to be wired, allowing the
bring-up to be synchronised (and provide debug information). The framework
can further be used to handle the rest of the per port events if and when
necessary.
Likewise, INTx signalling is implemented so that end-points can actually be
used.
Link: https://lore.kernel.org/r/20210929163847.2807812-7-maz@kernel.org
Link: https://lore.kernel.org/r/20211004150552.3844830-1-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Now that everything is in place at the poweroff sequence, this driver can
use module_platform_driver(), which allows it to be removed.
Link: https://lore.kernel.org/r/53b40494252444a9b830827922c4e3a301b8f863.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic under .remove ops is missing a call to dw_pcie_host_deinit(). Add
it, in order to allow the DWC core to be properly cleaned up.
Link: https://lore.kernel.org/r/838621e1c84ebaac153ccd9c36ea5e1254c61ead.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
The logic at kirin_pcie_gpio_request() enables some clkreq GPIO lines.
Disable them during power-off.
Link: https://lore.kernel.org/r/f403e590843de1a581cade2d534d34715706f54e.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Instead of having two copies of the same logic, place the power-off logic
in a separate function.
No functional changes.
Link: https://lore.kernel.org/r/64f6e8da3e5fff38b6c8fcb208ace46efe6555bb.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
There's nothing preventing this driver from being loaded as a module.
Change its config from bool to tristate.
Link: https://lore.kernel.org/r/b5e7cfe9df09b492750bd6db0f0c911eaae8c2d4.1634812676.git.mchehab+huawei@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Xiaowei Song <songxiaowei@hisilicon.com>
Apple's PCIe controller requires clocks to be configured in order to
bring up the hardware. Add the register pokes required to do so.
Adapted from Corellium's driver via Mark Kettenis's U-Boot patches.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-6-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add a minimal driver to bring up the PCIe bus on Apple system-on-chips,
particularly the Apple M1. This driver exposes the internal bus used for
the USB type-A ports, Ethernet, Wi-Fi, and Bluetooth. Bringing up the
radios requires additional drivers beyond what's necessary for PCIe itself.
Co-developed-by: Stan Skowronek <stan@corellium.com>
Link: https://lore.kernel.org/r/20210929163847.2807812-5-maz@kernel.org
Signed-off-by: Stan Skowronek <stan@corellium.com>
Signed-off-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Just as we now allow an interrupt map to be parsed when part of an
interrupt controller, there is no reason to ignore an interrupt map that
would be part of a pci device node such as a root port since we already
allow interrupt specifiers.
Allow the matching of such property when local to the node of a PCI
device, which allows the device itself to use the interrupt map for for
its own purpose.
Link: https://lore.kernel.org/r/20210929163847.2807812-4-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
of_irq_parse_raw() has a baked assumption that if a node has an
interrupt-controller property, it cannot possibly also have an
interrupt-map property (the latter being ignored).
This seems to be an odd behaviour, and there is no reason why we should
avoid supporting this use case. This is specially useful when a PCI root
port acts as an interrupt controller for PCI endpoints, such as this:
pcie0: pcie@690000000 {
[...]
port00: pci@0,0 {
device_type = "pci";
[...]
#address-cells = <3>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 7>;
interrupt-map = <0 0 0 1 &port00 0 0 0 0>,
<0 0 0 2 &port00 0 0 0 1>,
<0 0 0 3 &port00 0 0 0 2>,
<0 0 0 4 &port00 0 0 0 3>;
};
};
Handle it by detecting that we have an interrupt-map early in the parsing,
and special case the situation where the phandle in the interrupt map
refers to the current node (which is the interesting case here).
Link: https://lore.kernel.org/r/20210929163847.2807812-3-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
of_phandle_args_to_fwspec() can be generally useful to code extracting a DT
of_phandle and using an irq_fwspec to use the hierarchical irqdomain API.
Make it visible to the rest of the kernel, including modules.
Link: https://lore.kernel.org/r/20210929163847.2807812-2-maz@kernel.org
Tested-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Host crashes when pci_enable_atomic_ops_to_root() is called for VFs with
virtual buses. The virtual buses added to SR-IOV have bus->self set to NULL
and host crashes due to this.
PID: 4481 TASK: ffff89c6941b0000 CPU: 53 COMMAND: "bash"
...
#3 [ffff9a9481713808] oops_end at ffffffffb9025cd6
#4 [ffff9a9481713828] page_fault_oops at ffffffffb906e417
#5 [ffff9a9481713888] exc_page_fault at ffffffffb9a0ad14
#6 [ffff9a94817138b0] asm_exc_page_fault at ffffffffb9c00ace
[exception RIP: pcie_capability_read_dword+28]
RIP: ffffffffb952fd5c RSP: ffff9a9481713960 RFLAGS: 00010246
RAX: 0000000000000001 RBX: ffff89c6b1096000 RCX: 0000000000000000
RDX: ffff9a9481713990 RSI: 0000000000000024 RDI: 0000000000000000
RBP: 0000000000000080 R8: 0000000000000008 R9: ffff89c64341a2f8
R10: 0000000000000002 R11: 0000000000000000 R12: ffff89c648bab000
R13: 0000000000000000 R14: 0000000000000000 R15: ffff89c648bab0c8
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#7 [ffff9a9481713988] pci_enable_atomic_ops_to_root at ffffffffb95359a6
#8 [ffff9a94817139c0] bnxt_qplib_determine_atomics at ffffffffc08c1a33 [bnxt_re]
#9 [ffff9a94817139d0] bnxt_re_dev_init at ffffffffc08ba2d1 [bnxt_re]
Per PCIe r5.0, sec 9.3.5.10, the AtomicOp Requester Enable bit in Device
Control 2 is reserved for VFs. The PF value applies to all associated VFs.
Return -EINVAL if pci_enable_atomic_ops_to_root() is called for a VF.
Link: https://lore.kernel.org/r/1631354585-16597-1-git-send-email-selvin.xavier@broadcom.com
Fixes: 35f5ace5de ("RDMA/bnxt_re: Enable global atomic ops if platform supports")
Fixes: 430a23689d ("PCI: Add pci_enable_atomic_ops_to_root()")
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
We already include <linux/device.h> and <linux/msi.h>, which
include <asm/device.h> and <asm/msi.h>.
Drop the redundant includes of <asm/device.h> and <asm/msi.h>.
[bhelgaas: squash in fix from Wan Jiabing <wanjiabing@vivo.com>:
https://lore.kernel.org/r/20211104063720.29375-1-wanjiabing@vivo.com]
Link: https://lore.kernel.org/r/20211013003145.1107148-1-kw@linux.com
Signed-off-by: Krzysztof Wilczyński <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Derrick <jonathan.derrick@linux.dev>
If an error occurs after a successful cdns_pcie_init_phy() call, it must be
undone by a cdns_pcie_disable_phy() call, as already done above and below.
Update the goto to branch at the correct place of the error handling path.
Link: https://lore.kernel.org/r/db477b0cb444891a17c4bb424467667dc30d0bab.1624794264.git.christophe.jaillet@wanadoo.fr
Fixes: 49e0efdce7 ("PCI: j721e: Add support to provide refclk to PCIe connector")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
