With the radeon driver loaded the HP Compaq dc5750
Small Form Factor machine fails to resume from suspend.
Adding a quirk similar to other devices avoids
the problem and the system resumes properly.
Signed-off-by: Jeffery Miller <jmiller@neverware.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
sync_resv is to handle both amdgpu_fence and sched_fence.
Signed-off-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian K?nig <christian.koenig@amd.com>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Port of:
drm/radeon/atom: Send out the full AUX address
to amdgpu
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
On GMCH plaforms we are now getting the following spew on aux
interrupts:
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_get_hpd_pins] hotplug event received, stat 0x00000000, dig 0x00000000, pins 0x00000000
[drm:intel_dp_aux_ch] dp_aux_ch timeout status 0x71450064
Prevent it by not calling intel_get_hpd_pins() unless one of the HPD
interrupt bits are actually set.
I already fixed similar annoyance once with
4bca26d0a6 drm/i915: Use HOTPLUG_INT_STATUS_G4X on VLV/CHV
but another source for it got added in
fd63e2a972 drm/i915: combine i9xx_get_hpd_pins and pch_get_hpd_pins
due to pch_get_hpd_pins() being chosen over i9xx_get_hpd_pins() to
serve as the new unified piece of code. pch_get_hpd_pins() had the debug
print, and i9xx_get_hpd_pins() didn't.
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rewrite the BXT hpd setup to match the way we do it on other platforms:
- Throw out BXT_HOTPLUG_CTL since it's the same as PCH_PORT_HOTPLUG
- Enable the HPD bits in the DE port IER in gen8_de_irq_postinstall()
- Update DE port IMR using bdw_update_port_irq()
Also throw out port D from bxt_port_hotplug_long_detect() since BXT only
goes up to C.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A lot of the hpd irq handling is duplicated code, so refactor it a bit
by observing that in several places the only difference is the hpd[]
array. So pull the code to a few functions and pass in the hpd[] array
from the caller. Another option would be to determine the correct array
to use within the functions themselves, but somehow passing it in felt
nicer.
Further code reduction could be achieved by passing in the hotplug
register offset, and the long pulse detection function pointer. But that
didn't feel as good for some reason, so I left it at the middle ground.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
bxt_hpd_handler() looks different to everyone else for no good reason.
Rewrite it to use the standard variable namees etc.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Runtime suspends disabled all interrupts, so in order to get them back
fully we need to also do the HPD irq setup on runtime resume. Except
on VLV/CHV where the display interrupt initialization is part of the
display power well powerup.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On SKL the port A HPD has moved to the PCH. Hook it up.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Wire up the port A HPD for BDW. Compared to earlier platforms the
interrupt setup is a bit different, but basically everything else
looks the same.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Check for BDW before processing the HPD to not break BXT
Set found=true when processing port A HPD
Sort out the mess I made of the irq setup in v1
Warn about bad irq mask vs. enable bits in bdw_update_port_irq() (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If the CPU and PCH are on the same package we must enabled the port A
HPD also in the south hotplug register. To identify the package type
we simply look at the PCH type: LPT-H means separate package, and
LPT-LP means multi chip package (MCP).
v2: Add comment and pimp commit message
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
As with ILK/SNB wire up the port A HPD on IVB/HSW.
This might be more important on HSW with PSR. BSpec tells us that if the
automagic link training performed by the hardware fails for some reason,
we're going to get a short HPD and are supposed to re-train the link
manyally.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Add a comment about the pulse duration bits being reserved on HSW+
like we have for LPT+ in ibx_hpd_irq_setup()
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ILK/SNB support port A HPD. While HPD is optional on eDP let's at least
try to wite it up so that we might notice if the link has issues.
The eDP spec suggests that if HPD is not wired up, one should poll the
link status instead. We don't even do that currently.
v2: 0 initialize pin_mask/long_mask due to intel_get_hpd_pins() changes
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Starting from SPT the only interrupts living in the south are GMBUS and
HPD. What's worse some of the SPT specific new bits conflict with some
other bits on earlier PCH generations. So better not use the
cpt_irq_handler() for SPT+ anymore.
Also kill the hand rolled port E handling with something more
standardish. This also avoids accidentally confusing port B and port E
long pulses since the bits occupy the same positions, just in different
registers.
Also add a comment noting that the short pulse duration bits are
reserved on LPT+. The 2ms value we program is 0, so no issue wrt. the
MBZ in the spec.
v2: Call intel_hpd_irq_handler() only once (Paulo)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move the 0 initialization of pin_mask and long_mask from
intel_get_hpd_pins() into each caller. This we we can call
intel_get_hpd_pins() multiple times to accumulate more pins from several
sources.
v2: Add a comment explaining the dangers of intel_get_hpd_pins() (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The PORTA HPD defines are not BXT specific. They also exist on SPT,
and partially already on LPT:LP.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make LPT:LP checks look neater by wrapping the details in a
new HAS_PCH_LPT_LP() macro.
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Extract the core of ironlake_{enable,disable}_display_irq() into a new
function. We'll have further use for it later.
v2: Warn about invalid mask vs. enable bits (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Eliminate a bunch of duplicated code that calculates the currently
enabled HPD interrupt bits.
v2: s/;/:/ in patch subject (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Indent the PORTx_HOTPLUG_... defines appropriately, and fix some space
vs. tab issues.
v2: Document pre-HSW/LPT bits, and order another tab (Paulo)
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Forgot to do that in
commit d328c9d78d
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Apr 10 16:22:37 2015 +0200
drm/i915: Select starting pipe bpp irrespective or the primary plane
and it's confusing. Fix it.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Looking other drm drivers, there is no the restriction that framebuffer
has only one buffer in .create_handle() callback. They use just first
buffer.
If this limitation is removed, there is no reason keeping buffer count
for framebuffer, so we can remove buf_cnt from struct exynos_drm_fb.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
We can get buffer count of framebuffer using drm_format_num_planes(), so
keeping exynos_drm_fb_get_buf_cnt() is unnecessary.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This modifies exynos_drm_framebuffer_init() to be possible to support
multiple buffers. Then it can be used by exynos_user_fb_create().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Current codes get first gem object and then again get remain gem
objects. They can be unified to one routine.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch moves codes to update fb_info into exynos_drm_fbdev_update(),
so fb_info is updated via only one function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
It can get exynos_gem object via function argument, so no need to call
exynos_drm_fb_gem_obj() in exynos_drm_fbdev_update.
It also can get struct drm_framebuffer *fb via helper->fb, so can remove
a function argument for it.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The variable name "exynos_gem_obj" is too long, so some lines exceed 80
characters. It's simple to use "obj" instead of "exynos_gem_obj".
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The exynos_drm_fb_set_buf_cnt() is used to set buffer count only in
exynos_drm_fbdev_update(). This patch sets directly buffer count in
exynos_drm_framebuffer_init() without using exynos_drm_fb_set_buf_cnt(),
so there is no any reason to keep exynos_drm_fb_set_buf_cnt().
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The cases of the switch statement ensure that reg_type
can never be REG_TYPE_NONE here.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The size check was incomplete. It only computed the
size of area of the drawing rectangle and checked if
the size still fit inside the buffer.
The correct check is to compute the position of the
last byte that the G2D engine is going to access and
then check if that position is still contained in the
buffer. In particular we need the stride information
to determine this.
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Pass the correct hpd[] array to intel_get_hpd_pins() on pre-g4x
platforms.
This got broken in the following commit:
commit fd63e2a972
Author: Imre Deak <imre.deak@intel.com>
Date: Tue Jul 21 15:32:44 2015 -0700
drm/i915: combine i9xx_get_hpd_pins and pch_get_hpd_pins
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Egbert Eich <eich@suse.de>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There have been many hard to track down bugs whereby userspace forgot to
flag a write buffer and then cause graphics corruption or a hung GPU
when that buffer was later purged under memory pressure (as the buffer
appeared clean, its pages would have been evicted rather than preserved
and any changes more recent than in the backing storage would be lost).
In retrospect this is a rare optimisation against memory pressure,
already the slow path. If we always mark the buffer as dirty when
accessed by the GPU, anything not used can still be evicted cheaply
(ideal behaviour for mark-and-sweep eviction) but we do not run the risk
of corruption. For correct read serialisation, userspace still has to
notify when the GPU writes to an object. However, there are certain
situations under which userspace may wish to tell white lies to the
kernel...
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Kristian Høgsberg <krh@bitplanet.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: "Goel, Akash" <akash.goel@intel.co>
Cc: Michał Winiarski <michal.winiarski@intel.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
To help with debugging i2c-over-aux issues, add a module parameter than
can be used to tweak the assumed i2c bus speed, and thus the maximum
number of retries we will do for each aux message.
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Calculate the number of retries we should do for each i2c-over-aux
message based on the time it takes to perform the i2c transfer vs. the
aux transfer. We assume the shortest possible length for the aux
transfer, and the longest possible (exluding clock stretching) for the
i2c transfer.
The DP spec has some examples on how to calculate this, but we don't
calculate things quite the same way. The spec doesn't account for the
retry interval (assumes immediate retry on defer), and doesn't assume
the best/worst case behaviour as we do.
Note that currently we assume 10 kHz speed for the i2c bus. Some real
world devices (eg. some Apple DP->VGA dongle) fails with less than 16
retries. and that would correspond to something close to 15 kHz (with
our method of calculating things) But let's just go for 10 kHz to be
on the safe side. Ideally we should query/set the i2c bus speed via
DPCD but for now this should at leaast remove the regression from the
1->16 byte trasnfer size change. And of course if the sink completes
the transfer quicker this shouldn't slow things down since we don't
change the interval between retries.
I did a few experiments with a DP->DVI dongle I have that allows you
to change the i2c bus speed. Here are the results of me changing the
actual bus speed and the assumed bus speed and seeing when we start
to fail the operation:
actual i2c khz assumed i2c khz max retries
1 1 ok -> 2 fail 211 ok -> 106 fail
5 8 ok -> 9 fail 27 ok -> 24 fail
10 17 ok -> 18 fail 13 ok -> 12 fail
100 210 ok -> 211 fail 2 ok -> 1 fail
So based on that we have a fairly decent safety margin baked into
the formula to calculate the max number of retries.
Fixes a regression with some DP dongles from:
commit 1d002fa720
Author: Simon Farnsworth <simon.farnsworth@onelan.co.uk>
Date: Tue Feb 10 18:38:08 2015 +0000
drm/dp: Use large transactions for I2C over AUX
v2: Use best case for AUX and worst case for i2c (Simon Farnsworth)
Add a define our AUX retry interval and account for it
v3: Make everything usecs to avoid confusion about units (Daniel)
Add a comment reminding people about the AUX bitrate (Daniel)
Use DIV_ROUND_UP() since we're after the "worst" case for i2c
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Tested-by: moosotc@gmail.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91451
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Currently we react to native and i2c defers by waiting either 400-500 us
or 500-600 us, depending on which code path we take. Consolidate them
all to one define AUX_RETRY_INTERVAL which defines the minimum interval.
Since we've been using two different intervals pick the longer of them
and define AUX_RETRY_INTERVAL as 500 us. For the maximum just use
AUX_RETRY_INTERVAL+100 us.
I want to have a define for this so that I can use it when calculating
the estimated duration of i2c-over-aux transfers. Without a define it
would be very easy to change the sleep duration and neglect to update
the i2c-over-aux estimates.
Cc: Simon Farnsworth <simon.farnsworth@onelan.com>
Cc: moosotc@gmail.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Backmerge -fixes since there's more DDI-E related cleanups on top of
the pile of -fixes for skl that just landed for 4.3.
Conflicts:
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i914/intel_dp.c
drivers/gpu/drm/i915/intel_lrc.c
Conflicts are all fairly harmless adjacent line stuff.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
This makes the error message slightly more useful.
Changes since v1:
- Use ktime_get() while irqs are still disabled. (vsyrjala)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
There's already a per crtc member that can be used for it.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When i915 drivers run inside a VM with Intel GVT-g, some explicit
notifications are needed from guest to host device model through PV
INFO page write. The notifications include:
PPGTT create
PPGTT destroy
They are used for the shadow implementation of PPGTT. Intel GVT-g
needs to write-protect the guest pages of PPGTT, and clear the write
protection when they end their life cycle.
v2:
- Use lower_32_bits()/upper_32_bits() for qword operations;
- Remove the notification of guest context creation/destroy;
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some more definitions in the PV info page are added. They are mainly
for the guest notification to Intel GVT-g device model. They are used
for Broadwell enabling.
The notification of PPGTT page table creation/destroy is to notify
GVT-g device model the life cycle of guest page tables. Then device
model will implement shadow page table for guests.
The notification of context create/destroy is optional. If it is used,
the device model will create/destroy shadow context corresponding to
the context's life cycle. Guest driver needs to make sure that the
context's LRCA and backing storage address unchanged. If it is not
used, the device model will perform the context shadow work in the
context scheduling time.
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Broadwell hardware supports both ring buffer mode and execlist mode.
When i915 runs inside a VM with Intel GVT-g, we allow execlist mode
only.
The main reason of EXECLIST only is that GVT-g does not support the
dynamic mode switch between ring buffer mode and execlist mode when
running multiple virtual machines.
v2:
- Adjust the position of vgpu check in sanitize function (Joonas)
- Add vgpu error check in context initialization. (Joonas, Daniel)
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This is based on Mika Kuoppala's patch below:
http://article.gmane.org/gmane.comp.freedesktop.xorg.drivers.intel/61104/match=workaround+hw+preload
The patch will preallocate the page directories for 32-bit PPGTT when
i915 runs inside a virtual machine with Intel GVT-g. With this change,
the root pointers in EXECLIST context will always keep the same.
The change is needed for vGPU because Intel GVT-g will do page table
shadowing, and needs to track all the page table changes from guest
i915 driver. However, if guest PPGTT is modified through GPU commands
like LRI, it is not possible to trap the operations in the right time,
so it will be hard to make shadow PPGTT to work correctly.
Shadow PPGTT could be much simpler with this change. Meanwhile
hypervisor could simply prohibit any attempt of PPGTT modification
through GPU command for security.
The function gen8_preallocate_top_level_pdps() in the patch is from
Mika, with only one change to set "used_pdpes" to avoid duplicated
allocation later.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Zhiyuan Lv <zhiyuan.lv@intel.com>
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the audio codec is enabled or disabled, notify the audio driver.
This will enable the audio driver to get the notification at all times
(even when audio is in different powersave states).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a common function to return "yes" or "no" string based on the
argument, and drop the local versions of it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make it available outside of intel_dp.c.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If rc6 is enabled, notify GuC so it can do proper forcewake before
command submission.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The firmware layout changes that now it only has css header +
uCode + RSA signature. Plus, other trivial changes to support
GuC V4.3.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The driver doesn't support UMS any more, so set DRIVER_MODESET by default,
remove the legacy s/r callbacks, and rename the s/r functions to make it more clear
they're only in use by switcheroo now.
Also remove an obsolete comment about atomic. Normal updates are supported only
async updates aren't yet.
v2: Don't unconditionally set DRIVER_ATOMIC, we're not yet there.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make the code mode readable by pulling the "does this crtc have any
encoders?" deduction into a separate function.
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The BIOS sometimes likes to enable pipes w/o any ports, at least on
older machines. Currently we fail to assign anything sensible to
crtc->hwmode.crtc_clock which leads to complaints from the vblank code.
Deal with active pipes w/o ports and assign something sensible to
crtc_clock in i9xx_get_pipe_config(). The encoder .get_config() will
override this if the port is enabled.
Gets rid of rest of these on my gen4:
[drm:drm_calc_timestamping_constants [drm]] *ERROR* crtc 24: Can't calculate constants, dotclock = 0!
[drm:i915_get_vblank_timestamp] crtc 1 is disabled
v2: Fill out crtc_clock already in i9xx_get_pipe_config() (Maarten)
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At various points when changing the DPIO lane/phy power states,
construct an expected value of the DISPLAY_PHY_STATUS register
and compare it with the real thing.
To construct the expected value we look at our shadow PHY_CONTROL
register value (which should match what we've just written to the
hardware), and we also need to look at the actual state of the cmn
power wells as a disabled power well causes the relevant LDO status
to be reported as 'on' in DISPLAY_PHY_STATUS.
When initially powering up the PHY it performs various internal
calibrations for which it fully powers up. That means that if we check
for the expetected power state immediately upon releasing cmnreset we
would get the occasional false positive. But we can of course
poll until the expected value appears. It shouldn't be too long so
this shouldn't make modesets substantially longer.
One extra complication is introduced when we cross the streams, ie.
drive port B with pipe B. In this case we trick CL2 (where the DPLL lives)
into life by temporaily powering up the lanes in the second channel,
and once the pipe is up and runnign we release the lane power override.
At that point the power state of CL2 has somehow gotten entangled with
the power state of the first channel. That means that constructing the
expected DISPLAY_PHY_STATUS value is a bit tricky since based on the
lane power states in the second channel, CL2 should also be powered
down. But we can use the DPLL enable bit to determine when CL2 should
be alive even if the lanes are powered down. However the power state
of CL2 isn't actually tied in with the DPLL state, but to the state
of the lanes in first channel, so we have to avoid checking the
expected state between shutting down the DPLL and powering down
the lanes in the first channel. So no calling assert_chv_phy_status()
before the DISPLAY_PHY_CONTROL write in chv_phy_powergate_lanes(),
but after the write is a safe time to check.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add some checks that the state of the DPIO lanes is more or less what we
expect based on the overrides.
The hardware only provides two bits per channel indicating whether all
or some of the lanes are powered down, so we can't do an exact check.
Additionally, CL2 powering down before we can check it adds another
twist. To work around this we simply check for the 0 value of the
CL2 register (which is what we get when it's powered down) and
adjust our expectations.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we release the lane soft reset before lane stagger settings
have been programmed. I believe that means we don't actually do lane
staggering. So move the soft reset deassert to happen after lane
staggering has been programmed.
The one confusing thing in this is that when we remove the power down
override from the lanes, they power up with defaul register values,
which do not have the soft reset overrides enabled. And according to
some docs by default the data lane resets are tied to cmnreset. So that
would mean that lanes would come out of reset without staggering as
soon as the power down overrides are removed. But since we can't access
either the lane stagger register nor the soft reset override registers
until the lanes are powered on, we can't really do anything about it.
So let's just set the soft reset overrides as soon as the lane is
powered on and hope for the best.
v2: Fix typos in commit message (Daniel)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Deepak S <deepak.s@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The DP MST encoder config function never sets ddi_pll_sel, even though
its value is programmed in its ->pre_enable() hook. That used to work
because a new pipe_config was kzalloc'ed at every modeset, and the value
of zero selects the highest clock for the PLL. Starting with the commit
below, the value of ddi_pll_sel is preserved through modesets, and since
the correct value wasn't properly setup by the MST code, it could lead
to warnings and blank screens.
commit 8504c74c7a
Author: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Date: Fri May 15 11:51:50 2015 +0300
drm/i915: Preserve ddi_pll_sel when allocating new pipe_config
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91628
Cc: stable@vger.kernel.org # 7e6313a251 drm/i915: Don't use link_bw for PLL setup
Cc: stable@vger.kernel.org
Cc: Timo Aaltonen <tjaalton@ubuntu.com>
Cc: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This was forgotten in
commit d351f6d948
Author: Francisco Jerez <currojerez@riseup.net>
Date: Fri May 29 16:44:15 2015 +0300
drm/i915: Add SCRATCH1 and ROW_CHICKEN3 to the register whitelist.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: s/intel_dp_tps/drm_dp_tps/.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use port_clock instead of link_bw when picking the PLL parameters for
DP. link_bw may be zero with an eDP 1.4 sink that supports
DP_LINK_RATE_SET so we shouldn't use it for anything other than feed it
to the sink appropriately.
v2: Fix typo in commit message (Sivakumar)
Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: cherry-picked from future.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Applications like gnome-shell may try to render after dropping master
privileges. Since the driver should now be safe against this scenario,
allow those applications to use their legacy node like a render node.
v2: Add missing return statement.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Sinclair Yeh <syeh@vmware.com>
Commit ec9f932ed4
"drm/atomic: Cleanup on error properly in the atomic ioctl."
cleaned up some error paths, but didn't fix the TEST_ONLY path.
In the check only case plane->fb shouldn't be updated, and
the vblank events should be cleared as on failure.
Changes since v1:
- Fix -EDEADLK handling of vblank events too.
- Free state last with CHECK_ONLY.
Changes since v2:
- Add comment about freeing crtc_state->event with TEST_ONLY.
(Daniel Stone)
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Commit 92122789b2 ("drm/i915: preserve SSC if previously set v3")
added code to intel_modeset_gem_init to override the SSC status read
from VBT with the SSC status set by BIOS.
However, intel_modeset_gem_init is invoked *after* intel_modeset_init,
which calls intel_setup_outputs, which *modifies* SSC status by way of
intel_init_pch_refclk. So unlike advertised, intel_modeset_gem_init
doesn't preserve the SSC status set by BIOS but whatever
intel_init_pch_refclk decided on.
This is a problem on dual gpu laptops such as the MacBook Pro which
require either a handler to switch DDC lines, or the discrete gpu
to proxy DDC/AUX communication: Both the handler and the discrete
gpu may initialize after the i915 driver, and consequently, an LVDS
connector may initially seem disconnected and the SSC therefore
is disabled by intel_init_pch_refclk, but on reprobe the connector
may turn out to be connected and the SSC must then be enabled.
Due to 92122789b2 however, the SSC is not enabled on reprobe since
it is assumed BIOS disabled it while in fact it was disabled by
intel_init_pch_refclk.
Also, because the SSC status is preserved so late, the preserved value
only ever gets used on resume but not on panel initialization:
intel_modeset_init calls intel_init_display which indirectly calls
intel_panel_use_ssc via multiple subroutines, *before* the BIOS value
overrides the VBT value in intel_modeset_gem_init (intel_panel_use_ssc
is the sole user of dev_priv->vbt.lvds_use_ssc).
Fix this by moving the code introduced by 92122789b2 from
intel_modeset_gem_init to intel_modeset_init before the invocation
of intel_setup_outputs and intel_init_display.
Add a DRM_DEBUG_KMS as suggested way back by Jani:
http://lists.freedesktop.org/archives/intel-gfx/2014-June/046666.html
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=88861
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=61115
Tested-by: Paul Hordiienko <pvt.gord@gmail.com>
[MBP 6,2 2010 intel ILK + nvidia GT216 pre-retina]
Tested-by: William Brown <william@blackhats.net.au>
[MBP 8,2 2011 intel SNB + amd turks pre-retina]
Tested-by: Lukas Wunner <lukas@wunner.de>
[MBP 9,1 2012 intel IVB + nvidia GK107 pre-retina]
Tested-by: Bruno Bierbaumer <bruno@bierbaumer.net>
[MBP 11,3 2013 intel HSW + nvidia GK107 retina -- work in progress]
Fixes: 92122789b2 ("drm/i915: preserve SSC if previously set v3")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
and the addition of new clock drivers. Stephen Boyd has also done a lot
of subsystem-wide driver clean-ups (thanks!). There are also fixes to
the framework core and changes to better split clock provider drivers
from clock consumer drivers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QAiQ
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The clk framework changes for 4.3 are mostly updates to existing
drivers and the addition of new clock drivers. Stephen Boyd has also
done a lot of subsystem-wide driver clean-ups (thanks!). There are
also fixes to the framework core and changes to better split clock
provider drivers from clock consumer drivers"
* tag 'clk-for-linus-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (227 commits)
clk: s5pv210: add missing call to samsung_clk_of_add_provider()
clk: pistachio: correct critical clock list
clk: pistachio: Fix PLL rate calculation in integer mode
clk: pistachio: Fix override of clk-pll settings from boot loader
clk: pistachio: Fix 32bit integer overflows
clk: tegra: Fix some static checker problems
clk: qcom: Fix MSM8916 prng clock enable bit
clk: Add missing header for 'bool' definition to clk-conf.h
drivers/clk: appropriate __init annotation for const data
clk: rockchip: register pll mux before pll itself
clk: add bindings for the Ux500 clocks
clk/ARM: move Ux500 PRCC bases to the device tree
clk: remove duplicated code with __clk_set_parent_after
clk: Convert __clk_get_name(hw->clk) to clk_hw_get_name(hw)
clk: Constify clk_hw argument to provider APIs
clk: Hi6220: add stub clock driver
dt-bindings: clk: Hi6220: Document stub clock driver
dt-bindings: arm: Hi6220: add doc for SRAM controller
clk: atlas7: fix pll missed divide NR in fraction mode
clk: atlas7: fix bit field and its root clk for coresight_tpiu
...
From B spec, DDI_E port belong to PowerWell 2, but
DDI_E share the powerwell_req/staus register bit with
DDI_A which belong to DDI_A_E_POWER_WELL.
In order to communicate with the connector on DDI-E, both
DDI_A_E_POWER_WELL and POWER_WELL_2 must be enabled.
Currently intel_dp_power_get(DDI_E) only enable
DDI_A_E_POWER_WELL, this patch will not only enable
DDI_a_E_POWER_WELL but also enable POWER_WELL_2.
This patch also fix the DDI-E hotplug function.
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Port of:
drm/radeon/atom: Send out the full AUX address
to radeon non-atom aux path
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
AUX addresses are 20 bits long. Send out the entire address instead of
just the low 16 bits.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: "Christian König" <christian.koenig@amd.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Enable eDP on DDI-E.
Also let's remove duplicated definitions to avoid later confusion.
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There are OEMs using DDI-E out there,
so let's enable it.
Unfortunately there is no detection bit for DDI-E
So we need to rely on VBT for that.
I also need to give credits to Xiong since before seing
his approach to check info->support_* I was creating an ugly
vbt->ddie_sfuse_strap in order to propagate the ddi presence info
v2: Rebased as last patch in the series. since all other patches
in this series are needed for anything working propperly on DDI-E.
Credits-to: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Cc: "Zhang, Xiong Y" <xiong.y.zhang@intel.com>
Reviewed-by: Xiong Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
DDI-E doesn't have the correspondent GMBUS pin.
We rely on VBT to tell us which one it being used instead.
The DVI/HDMI on shared port couldn't exist.
This patch isn't tested without hardware wchich has HDMI
on DDI-E.
v2: fix trailing whitespace
v3: MISSING_CASE take place of BUG()
Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
commit da2bc1b9db
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Oct 23 19:23:26 2014 +0300
drm/i915: add poweroff_late handler
introduced a regression on old platforms during hibernation. A workaround was
added in
commit ab3be73fa7
Author: Imre Deak <imre.deak@intel.com>
Date: Mon Mar 2 13:04:41 2015 +0200
drm/i915: gen4: work around hang during hibernation
using an explicit blacklist for the GENs/BIOS vendors where the issue was
reported. Later there we had reports of the same failure on platforms not on
this list.
To my best knowledge the correct thing to do is still to put the device to PCI
D3 state during hibernation, see [1] and [2] for the reasons. This also aligns
with our future plans to unify more the runtime and system suspend/resume
paths. Since an exact blacklist seems to be impractical (multiple GENs and
BIOS vendors are affected) apply the workaround on everything pre GEN6.
[1] http://lists.freedesktop.org/archives/intel-gfx/2015-February/060710.html
[2] https://lkml.org/lkml/2015/6/22/274
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=95061
Reported-by: Ilya Tumaykin <itumaykin@gmail.com>
Reported-by: Dirk Griesbach <spamthis@freenet.de>
Reported-by: Pavel Machek <pavel@ucw.cz>
Reported-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Tested-by: Mikko Rapeli <mikko.rapeli@iki.fi>
Reported-by: Paul Bolle <pebolle@tiscali.nl>
CC: stable@vger.kernel.org
Signed-off-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We are no longer checkling the DP link status on long hpd. We used to do
that from the .hot_plug() handler, but it was removed when MST got
introduced.
If there's no userspace we now fail to retrain the link if the sink
power is toggled (or cable yanked and replugged), meaning the user is
left staring at a blank screen. With the retraining put back that should
be fixed.
Also remove the leftover comment that referred to the old retraining
from .hot_plug().
Fixes a regression introduced in:
commit 0e32b39cee
Author: Dave Airlie <airlied@redhat.com>
Date: Fri May 2 14:02:48 2014 +1000
drm/i915: add DP 1.2 MST support (v0.7)
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89453
Tested-by: Palmer Dabbelt <palmer@dabbelt.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91407
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89461
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89594
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=85641
Cc: Dave Airlie <airlied@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
This is a second pull-request which adds last part of
atomic modeset/pageflip support, render node support,
clean-up, and fix-up.
* 'exynos-drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: fix build warning to exynos_drm_gem.c
drm/exynos: Properly report supported formats for each device
drm/exynos: add render node support
drm/exynos: implement atomic_{begin/flush} of DECON
drm/exynos: remove legacy ->suspend()/resume()
drm/exynos: Enable atomic modesetting feature
drm/exynos: remove wait queue for pending page flip
drm/exynos: wait all planes updates to finish
drm/exynos: add atomic asynchronous commit
drm/exynos: fimd: only finish update if START == START_S
drm/exynos: add macro to get the address of START_S reg
drm/exynos: check for pending fb before finish update
drm/exynos: fimd: move window protect code to prepare/cleanup_plane
drm/exynos: add prepare and cleanup phases for planes
drm/exynos: fimd: unify call to exynos_drm_crtc_finish_pageflip()
drm/exynos: don't track enabled state at exynos_crtc
Some i915 fixes headed for v4.3. SKL DDI-E is a wip, but here's the
first in a series.
* tag 'drm-intel-next-fixes-2015-08-28' of git://anongit.freedesktop.org/drm-intel:
drm/i915/skl: enable DDI-E hotplug
drm/i915: Fix build warning on 32-bit
drm/i915/skl: Update DDI buffer translation programming.
drm/i915: Allow parsing of variable size child device entries from VBT
drm/i915: fix link rates reported for SKL
drm/i915: fix VBT parsing for SDVO child device mapping
Exynos DRM reported that all planes for all supported sub-devices supports
only three pixel formats: XRGB24, ARGB24 and NV12. This patch lets each
Exynos DRM sub-drivers to provide the list of supported pixel formats
and registers this list to DRM core.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
This patch allows clients who want to use render node to access
rendering relevant ioctls - g2d, post processor and gem allocation.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Each CRTC's atomic_{begin/flush} must stop/start the update of shadow
registers to active register in the functions. This patch achieves these
purpose by moving the setting of protection bits to those functions from
decon_update_plane.
v2: rebased to the branch exynos-drm-next
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
These legacy helpers should only be used by shadow-attaching drivers.
KMS drivers has its own way to handle suspend/resume and don't need to
use these two helpers.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <daeinki@gmail.com>
From: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Now that atomic modesetting is implemented for exynos enable the
DRIVER_ATOMIC flag on the driver's features.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos atomic commit procedures already does this job of waiting for
pending updates to finish, that means using pending_flip_queue is
pointless now because the disable CRTC procedure will never happen
during a page_flip.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Add infrastructure to wait for all planes updates to finish by using
an atomic_t variable to track how many pending updates we are waiting
plus a wait_queue for the wait part.
It also changes vblank behaviour and keeps it enabled for all types
of updates
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The atomic modesetting interfaces supports async commits that should be
implemented by the drivers. If drm core requests an async commit
exynos_atomic_commit() will now schedule a work task to run the update later.
It also serializes commits that needs to run on the same crtc, putting the
following commit to wait until the current one is finished.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
fimd_update_plane() programs BUF_START[win] and during the update
BUF_START[win] is copied to BUF_START_S[win] (its shadow register)
and starts scanning out, then it raises a irq.
The fimd_irq_handler, in the case we have a pending_fb, will check
the fb value was copied to START_S register and finish the update
in case of success.
Based on patch from Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The current code was ignoring the end of update for all overlay planes,
caring only for the primary plane update in case of pageflip.
This change adds a change to start to check for pending updates for all
planes through exynos_plane->pending_fb. At the start of plane update the
pending_fb is set with the fb to be shown on the screen. Then only when to
fb is already presented in the screen we set pending_fb to NULL to
signal that the update was finished.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
fixup! drm/exynos: check for pending fb before finish update
Only set/clear the update bit in the CRTC's .atomic_begin()/flush()
so all planes are really committed at the same time.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
From: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
.prepare_plane() and .cleanup_plane() allows to perform extra operations
before and after the update of planes. For FIMD for example this will
be used to enable disable the shadow protection bit.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Unify handling of finished plane update to prepare for a following patch
that will check for the START and START_S regs to really make sure that
the plane was updated.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
struct drm_crtc already stores the enabled state of the crtc
thus we don't need to replicate enabled in exynos_drm_crtc.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The latter is a default version of <asm/mman.h> and not for driver use.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
Saving the current UVD state on suspend and restoring it on resume
just doesn't work reliable. Just close cleanup all sessions on suspend.
Ported from radeon commit "12e49feadff6d7b7ebbe852b36943a71524d8d34".
v2: rebased
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com> (v1)
This way the scheduler doesn't wait in it's work thread any more.
v2: fix race conditions
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Jammy Zhou <Jammy.Zhou@amd.com>
Since BIOS RC 1.4 it would enable CDCLK PLL during BIOS S3 resume, then
driver needs to set CDCLK to avoid display corruption if DPLL0 enabled.
References: https://bugs.freedesktop.org/show_bug.cgi?id=91697
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Reviewed-by: Wei Shun Chang <wei.shun.chang@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Xiong Y Zhang <xiong.y.zhang@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The copyright header in nvkm/engine/device/platform.c has been replaced
with the NVIDIA one from drm/nouveau_platform.c, as most of the actual
code is now theirs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Doesn't fix any known issue, but best be safe in case control is handed
to us from firmware with these left enabled.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This ensures we have a valid mask of disabled engines before we start
trying to execute fini()/init() on the subdevs, potentially touching
devices that don't exist.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
An upcoming commit requires being able to modify the PRAMIN BAR page
tables while already holding the MMU subdev mutex.
To solve this issue, each VM has been given its own mutex. As a nice
side-effect, this also allows separate VMs to be updated concurrently.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
A variety of tweaks to the NVIF library interfaces, mostly ripping out
things that turned out to be not so useful.
- Removed refcounting from nvif_object, callers are expected to not be
stupid instead.
- nvif_client is directly reachable from anything derived from nvif_object,
removing the need for heuristics to locate it
- _new() versions of interfaces, that allocate memory for the object
they construct, have been removed. The vast majority of callers used
the embedded _init() interfaces.
- No longer storing constructor arguments (and the data returned from
nvkm) inside nvif_object, it's more or less unused and just wastes
memory.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Replaces the piece-by-piece (in response to NV_DEVICE ctor args) device
contruction with a once-off all-or-nothing approach, eliminating some
tricky refcounting issues. The partial device init capability was only
required by some tools, and has been moved to probe time instead.
Temporarily removes a workaround for some boards where we need to fiddle
with AGP registers before executing the DEVINIT scripts. A later commit
in this series reinstates it.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
These require an explicit struct nvkm_gpuobj pointer, unlike the previous
macros which take a void *, and work with any nvkm_object.
New semantics require acquiring/releasing a gpuobj before accessing them,
which will be made use of in later patches to greatly reduce the overhead
of accesses, particularly when a direct mmio mapping of the object is not
available (suspend/resume, out of ioremap() space, and on GK20A).
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
