On SPEAr3xx, ethernet driver is not compatible with the SPEAr600
one.
Indeed, SPEAr3xx uses an earlier version of this IP (v3.40) and
needs some driver tuning compare to SPEAr600.
The v3.40 IP support was added to stmmac driver and this patch
fixes this issue and use the correct compatible string for
SPEAr3xx
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input pin that indicates that the BMC is configured to boot with security
protections enforced.
Pulled up by default (secure). Placing the jumper will pull the pin down
(bypass security).
When in the secure boot state, it makes the EEPROM at 0x50 on bus 14
read only.
Link: https://lore.kernel.org/r/20210923074606.283393-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fixes for omaps for v5.15
Few regression fixes for omaps for the v5.15-rc cycle. There is a fix
for boot time hangs that can happen on some am335x devices that started
when the pruss devicetree nodes were added. The other fixes are less
critical:
- Fix compiler warning for sysc_init_soc() that got recently introduced
- Fix external abort for am335x pruss as otherwise some am335x will hang
- Use CLKDM_NOAUTO quirk also for dra7 dcan1
- Fix older NAND device node regression for omap3-sdp
* tag 'omap-for-v5.15/fixes-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: omap3430-sdp: Fix NAND device node
bus: ti-sysc: Use CLKDM_NOAUTO for dra7 dcan1 for errata i893
soc: ti: omap-prm: Fix external abort for am335x pruss
bus: ti-sysc: Add break in switch statement in sysc_init_soc()
Link: https://lore.kernel.org/r/pull-1633609552-789682@atomide.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no such thing as a generic USB EHCI controller. The EHCI
controllers found on Tegra SoCs are instantiations that need Tegra-
specific glue to work properly, so drop the generic compatible string
and keep only the Tegra-specific ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>
i.MX fixes for 5.15, round 2:
- A couple of fixes from Haibo Chen to update SPI NOR TX bus width for
i.MX6 and i.MX8 boards. This becomes necessary because spi-nor driver
starts using the setting in DT.
- Mark buck2 always-on for i.MX8MM Kontron-n801x-som board to avoid the
core supply being turned off unexpectedly.
- Fix eSDHC2 device tree settings for LS1028A SoC.
- Disable GIC CPU interface before calling stby-poweroff sequence to fix
power-off failure on i.MX6.
- Fix M2_RST# GPIO pinmux on i.MX8M venice-gw7902 boards.
* tag 'imx-fixes-5.15-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8m*-venice-gw7902: fix M2_RST# gpio
ARM: imx6: disable the GIC CPU interface before calling stby-poweroff sequence
arm64: dts: ls1028a: fix eSDHC2 node
arm64: dts: imx8mm-kontron-n801x-som: do not allow to switch off buck2
arm64: dts: imx8: change the spi-nor tx
ARM: dts: imx: change the spi-nor tx
Link: https://lore.kernel.org/r/20211006125734.GA10197@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The Raspberry Pi Compute Module 4 (CM4) are SoMs which contain the
following:
* BCM2711 quad core processor
* up to 8 GB RAM
* up to 32 GB eMMC
* a GPIO expander
* Gigabit PHY BCM54210PE
* Wifi/BT module with internal and external antenna
The eMMC and the Wifi/BT module are optional.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1628334401-6577-9-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
The VEC has a different address (0x7ec13000) on the BCM2711 (used in
e.g. Raspberry Pi 4) compared to BCM283x (e.g. Pi 3 and earlier). This
was erroneously not taken account for.
Definition of the VEC in the devicetrees had to be moved from
bcm283x.dtsi to bcm2711.dtsi and bcm2835-common.dtsi to allow for this
differentiation.
Fixes: 7894bdc622 ("ARM: boot: dts: bcm2711: Add BCM2711 VEC compatible")
Signed-off-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1626980528-3835-1-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
BB2D is a Vivante GC 2D Accelerator.
This adds the node to the dts file within a target module node.
Crossbar index number is used for interrupt mapping.
Signed-off-by: Gowtham Tammana <g-tammana@ti.com>
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix typo in pinctrl. It did only work because the bootloader
seems to have initialized it.
Fixes: ee32711195 ("ARM: dts: omap3-gta04: Define and use bma180 irq pin")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add mandatory supply properties. The supply is always on, so it is just
a syntax issue, no functional change.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Replace depreciated nodenames, fix label name to match scheme.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hyphens should be used in label names. make dtbs_check complains
about that since it does not match the corresponding pattern
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Switch the compatible for the am33xx_pinmux pin controller node from
pinctrl-single to pinconf-single. The only change between these two
compatibles is that PCS_HAS_PINCONF will be true. This then allows
pinconf properties to be utilized.
The purpose of this change is to allow the PocketBeagle to use:
pinctrl-single,bias-pullup
pinctrl-single,bias-pulldown
This dts already defines these properites for gpio pins in the default
pinctrl state but it has no effect unless PCS_HAS_PINCONF is set.
The bias properties can then be modified on the corresponding gpio lines
through the gpiod uapi. The mapping between the pins and gpio lines is
defined by gpio-ranges under the gpio controller nodes in am33xx-l4.dtsi
Signed-off-by: Drew Fustini <drew@pdp7.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
i.MX fixes for 5.15:
- Revert cc8870bf4c to fix the regression on i.MX6 that suspend
support becomes broken.
- Add `qca,clk-out-frequency` property to fix Ethernet support on
imx6qdl-pico board.
- Re-enable FB support in imx_v6_v7_defconfig. It gets lost due to
f611b1e762 ("drm: Avoid circular dependencies for CONFIG_FB").
- Fix LP5562 LED support on imx6dl-yapp4 board.
- Add missing pinctrl-names for panel on M53Menlo board.
- Fix USB host power regulator polarity on M53Menlo board.
* tag 'imx-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: imx_v6_v7_defconfig: enable fb
ARM: dts: imx6qdl-pico: Fix Ethernet support
ARM: dts: imx: Fix USB host power regulator polarity on M53Menlo
ARM: dts: imx: Add missing pinctrl-names for panel on M53Menlo
Revert "ARM: imx6q: drop of_platform_default_populate() from init_machine"
ARM: dts: imx6dl-yapp4: Fix lp5562 LED driver probe
Link: https://lore.kernel.org/r/20210923063356.GK13480@dragon
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Juno/Vexpress fixes for v5.15
Bunch of DTS fixes to resolve addressing issues with some of the device
nodes, dropping unused/undocumented properties in various nodes, and
aligning node names with dtschema.
* tag 'juno-fixes-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
arm: dts: vexpress: Fix motherboard bus 'interrupt-map'
arm: dts: vexpress: Fix addressing issues with 'motherboard-bus' nodes
arm: dts: vexpress-v2p-ca9: Fix the SMB unit-address
arm: dts: vexpress: Drop unused properties from motherboard node
arm64: dts: arm: drop unused interrupt-names in MHU
ARM: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: arm: align watchdog and mmc node names with dtschema
arm64: dts: fvp: Remove panel timings
Link: https://lore.kernel.org/r/20210927105249.3583380-1-sudeep.holla@arm.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Qualcomm DTS fixes for v5.15
This corrects the use of depricated chipid and clock names, for which
support was finally dropped from the driver. It also ensures that the
DSI PLL is fed by the correct clock, now that it's being migrated to not
rely on global clock names.
* tag 'qcom-dts-fixes-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
ARM: dts: qcom: apq8064: update Adreno clock names
ARM: dts: qcom: apq8064: Use 27MHz PXO clock as DSI PLL reference
ARM: dts: qcom: apq8064: use compatible which contains chipid
Link: https://lore.kernel.org/r/20210930025526.1146-1-bjorn.andersson@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Add a label for the touchscreen to allow a custom baseboard to
disable this node if needed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The STMPE811 ADC on the Apalis SoM board can be used as a provider
of ADC capabilities to other devices, for example, when a custom
baseboard has an SN74LV4051 analog mux.
Pass the 'io-channel-cells' parameter to indicate such possibility.
While at it, also pass a label for the adc device, so that it can
be referenced in the custom baseboard.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is recommended not to use underscore in node names.
Change it to dash.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Tolino Vision 5 Ebook reader. It is
based on boards called ¨e70k02¨. It is equipped with an imx6sl SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This adds a devicetree for the Kobo Libra H2O Ebook reader. It is based on
boards called e70k02. It is equipped with an imx6sll SoC.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Netronix board E70K02 can be found some several Ebook-Readers,
at least the Kobo Libra H2O and the Tolino Vision 5. The board
is equipped with different SoCs requiring different pinmuxes.
For now the following peripherals are included:
- LED
- Power Key
- Cover (gpio via hall sensor)
- RC5T619 PMIC
- Backlight via lm3630a
- Wifi sdio chip detection (mmc-powerseq and stuff)
It is based on vendor kernel but heavily reworked due to many
changed bindings.
Known limitations: cold colored backlight does not work due to
incompatible hard coded overvoltage setting in the driver.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SPI-NOR flash on the SoM was missing from the device tree.
The TQMa7 as a designated QSPI_RESET# pin, however depending on the
hardware configuration the pin may be unconnected, or be used for a
different purpose. With this in mind, we mux the pin as a pullup and
define an input hog for it, but keep it a separate pin group, so that it
is easy for dependent Device Trees to modify the configuration.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Nexus 7 has OTG-cable microUSB port, enable OTG mode. USB peripheral
devices now can be connected to Nexus 7 using OTG adapter, switching
USB port into host mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Add new properties to USB PHYs needed for enabling USB OTG mode.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The host-wakeup GPIO is now marked as deprecated in the broadcom-bluetooth
device-tree binding, it's replaced with the host-wakeup interrupt. Update
Tegra device-trees to the recent version of the Bluetooth binding.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The "ak,ak8975" compatible is not recognized by dt-bindings, it's
deprecated. Use supported "asahi-kasei,ak8975" compatible.
Signed-off-by: David Heidelberg <david@ixit.cz>
Signed-off-by: Thierry Reding <treding@nvidia.com>
With commit c709135e57 ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823b ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
Datasheet chapter "EMAC Timings" specifies that while in 3.3V domain
GMAC's MDIO pins should be configured with slew-rate enabled, while the
data + signaling pins should be configured with slew-rate disabled when
GMAC works in RGMII or RMII modes. The pin controller for SAMA7G5 sets
the slew-rate as enabled for all pins. Adapt the device tree to comply
with these.
Fixes: 7540629e2f ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-2-claudiu.beznea@microchip.com
SAMA7G5-EK board has DDR3L type of memory soldered. This needs 1.35V. The
1.35V for DDR3L rail at run-time is selected by the proper configuration
on SELV2 pin (for 1.35V it needs to be in high-z state). When suspended
the MCP16502 PMIC soldered on SAMA7G5-EK will use different sets of
configuration registers to provide proper voltages on its rail. Run-time
configuration registers could be configured differently than suspend
configuration register for MCP16502 (VSEL2 affects only run-time
configuration). In suspend states the DDR3L memory soldered on SAMA7G5-EK
switches to self-refresh. Even on self-refresh it needs to be powered by
a 1.35V rail. Thus, make sure the PMIC is configured properly when system
is suspended.
Fixes: 7540629e2f (ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210930154219.2214051-2-claudiu.beznea@microchip.com
