For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the write_prph_64 of pcie to be transport agnostic.
Add direct write as well, as it is needed for a000 HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the scratch buffer is set to 16 bytes and indicates
the size of the bi-directional DMA.
However, next HW generation will perform additional offloading,
and will write the result in the key location of the TX command,
so the size of the bi-directional consistent memory should grow
accordingly - increase it to 40.
Generalize the code to get rid of now irrelevant scratch references.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In MQ environment and new architecture in early stages
we may encounter DMA issues. Track RXB status and bail
out in case we receive index to an RXB that was not
mapped and handed over to HW.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Upon firmware load interrupt (FH_TX), the ISR re-enables the
firmware load interrupt only to avoid races with other
flows as described in the commit below. When the firmware
is completely loaded, the thread that is loading the
firmware will enable all the interrupts to make sure that
the driver gets the ALIVE interrupt.
The problem with that is that the thread that is loading
the firmware is actually racing against the ISR and we can
get to the following situation:
CPU0 CPU1
iwl_pcie_load_given_ucode
...
iwl_pcie_load_firmware_chunk
wait_for_interrupt
<interrupt>
ISR handles CSR_INT_BIT_FH_TX
ISR wakes up the thread on CPU0
/* enable all the interrupts
* to get the ALIVE interrupt
*/
iwl_enable_interrupts
ISR re-enables CSR_INT_BIT_FH_TX only
/* start the firmware */
iwl_write32(trans, CSR_RESET, 0);
BUG! ALIVE interrupt will never arrive since it has been
masked by CPU1.
In order to fix that, change the ISR to first check if
STATUS_INT_ENABLED is set. If so, re-enable all the
interrupts. If STATUS_INT_ENABLED is clear, then we can
check what specific interrupt happened and re-enable only
that specific interrupt (RFKILL or FH_TX).
All the credit for the analysis goes to Kirtika who did the
actual debugging work.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The PCIe transport needs to store two pointers in each TX SKB, and
currently assumes mac80211's ieee80211_tx_info is present in the CB
to do that.
In order to remove that assumption, have the opmodes pass in the
offset to where the pointers can be stored in the CB and use the
offset in the PCIe code.
To make the disentanglement complete, remove mac80211.h includes
from everywhere in the generic iwlwifi code. This required adding
an include of cfg80211.h in one place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to properly record SKBs that didn't come through
mac80211, don't rely on the IEEE80211_TX_CTRL_PORT_CTRL_PROTO flag
but instead check for ETH_P_PAE directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to reduce reliance on mac80211 structs in the core
iwlwifi code, store the cipher schemes in the format given
by the firmware and convert it later, rather than storing it
in the mac80211 format.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Restart flow zeroes the rx_ba_sessions counter. Mac80211 asks
driver to tear down of the session only afterwards, and as a
result driver didn't free the data. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 10b2b2019d ("iwlwifi: mvm: add infrastructure for tracking BA session in driver")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make sure that in DQA mode, the SCD's configuration of a
queue is redirected to the lower AC of the streams of the
queue.
Make sure that this queue is redirected to the lowest AC
when adding a new RA/TID to an existing queue. If it isn't -
redirect the queue.
Also, as redirection revealed a bug in the marking of a
shared queue, this patch contains a small fix to make
sure a shared queue maintains the appropriate "shared queue
marking".
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support TDLS when working in DQA mode.
This is done mainly by NOT doing any special things
for TDLS, as the queues are dynamically created anyway,
so no need to allocate them ahead of time.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In cases of hardware or DMA error, the vid read from
a zeroed location will be 0, and we will access the rxb
at index 0 in the global table, while it may be NULL or
owned by hardware.
Invalidate vid 0 in order to detect the situation and
bail out.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This led to a DMA splat.
Fixes: a6c4fb4441 ("iwlwifi: mvm: Add FW paging mechanism for the UMAC on PCI")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This struct member is never set, so remove it.
Since this is the last thing that needs mac80211.h, also change
the includes to no longer use mac80211.h
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value for Channel 14 was wrong. Fix it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The TX fifos are arranged consecutively in the SMEM, beginning
with the regular fifos, and tailed by the internal fifos.
In the current code, while trying to read the internal fifos,
we read the fifos beginning with the index zero.
By doing this we actually re-read the regular fifos.
In order to read the internal fifos, start the reading index
from the number of regular fifos configured by the fw.
Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Fixes: 39654cb3a6 ("iwlwifi: don't access a nonexistent register upon assert")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a pretty ancient bug that hasn't manifested itself
until now.
The scratchbuf for command queue is allocated only for 32 slots
but is accessed with the queue write pointer - which can be
up to 256.
Since the scratch buf size was 16 and there are up to 256 TFDs
we never passed a page boundary when accessing the scratch buffer,
but when attempting to increase the size of the scratch buffer a
panic was quick to follow when trying to access the address resulted
in a page boundary.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 38c0f334b3 ("iwlwifi: use coherent DMA memory for command header")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
On some of the chipsets MSI & INTA interrupts are disabled by default in
the HW registers, and need to be explicitly enabled to be used.
In case MSI-X isn't used, make sure MSI mode is enabled by setting
the relevant HW register.
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Read the SAR BIOS table from the ACPI and parse it into the
iwl_mvm_sar_table structure. If the table is enabled, send it to the
firmware via REDUCE_TX_POWER_CMD.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We removed support for old API for coexistence, but we
forgot to remove defines and variable that are not needed
anymore.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Our HW does not support checksum of fragmented packets.
Fix code accordingly to checksum those packets in the driver.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Fixes: 5e6a98dc48 ("iwlwifi: mvm: enable TCP/UDP checksum support for 9000 family")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the state sent in SF configuration is always
FULL_ON.
This commit sets the correct state (e.g. INIT_OFF
when station is not associated).
Fixes: commit f4a3ee493e ("iwlwifi: mvm: Always enable the smart FIFO")
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The NIC's CPU gets started after the firmware has been
written to its memory. The first thing it does is to
send an interrupt to let the driver know that it is
running. In order to get that interrupt, the driver needs
to make sure it is not masked. Of course, the interrupt
needs to be enabled in the driver before the CPU starts to
run.
I mistakenly inversed those two steps leading to races
which prevented the driver from getting the alive interrupt
from the firmware.
Fix that.
Cc: <stable@vger.kernel.org> [4.5+]
Fixes: a6bd005fe9 ("iwlwifi: pcie: fix RF-Kill vs. firmware load race")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 family we will get extended statistics notification
with averaged data for RSSI, TCM and rogue AP detection.
Support it. Future patches will added the required algorithms.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer hardware supports GCMP and GCMP 256-bit ciphers.
Add support for adding/setting GCMP key for TX mode.
In the TX command handling GCMP-256 is handled in a different
way as the key size should be up to 128-bits:
Set the key value to the key index in the key table,
and specify that this key should be taken form the key table
instead of from the TX command.
While at it - convert security control flags to an enum.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support of dumping new RFH instead of FH registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc-6 reports the following error if -Werror=unused-const-variable
is enabled.
drivers/net/wireless/intel/iwlwifi/dvm/lib.c:210:21: error:
'iwlagn_loose_lookup' defined but not used
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix an issue where nullfunc frames and block ack requests
had the same tid as aggregation frames and were queued on
a non aggregation queue. The pending frames counter included
those frames but the check whether to decrement the pending
frames counter relied on the tid status and not on the txq id.
The result was an inconsistent state of the pending frames
counter followed by a failure to remove the station.
This failure triggered SYSASSERT 0x3421.
In addition, fix a situation in DQA mode where the number
of pending frames turned negative. This was due to the TX queue
being on the IWL_EMPTYING_HW_QUEUE_DELBA state and its frames
were still decremented.
Even though the SYSASSERT issue is fixed when DQA is disabled,
the issue is not completely solved when DQA is enabled and
should still be fixed.
Signed-off-by: Oren Givon <oren.givon@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
gcc is apparently unablel to track the state of the local 'resp_v2'
variable across the kzalloc() function, and warns about the response
variable being used without an initialization:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c: In function ‘iwl_mvm_update_mcc’:
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:727:36: warning: ‘mcc_resp_v1’ may be used uninitialized in this function [-Wmaybe-uninitialized]
resp_cp->n_channels = mcc_resp_v1->n_channels;
drivers/net/wireless/intel/iwlwifi/mvm/nvm.c:721:3: warning: ‘mcc_resp’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(resp_cp, mcc_resp, resp_len);
The warning showed up in x86 allmodconfig after my patch to
unhide -Wmaybe-uninitialized warnings by default was merged,
though it always existed in randconfig builds. I did not
catch the warning earlier because I was testing on ARM, which
never produced the warning.
This rearranges the code in a way that improves readability for
both humans and the compiler, and that avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 6fa52430f0 ("iwlwifi: mvm: change mcc update API")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Expand TLC to support 160MHz channels. Full support for A-MSDU
case will be added separately.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW sets status for each RX packet.
Enum in the driver doesn't match with FW definition - fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we try to open an aggregation for every packet (given that one
is not already open).
This causes redundant overhead (addba/delba) for null data packets.
Do not open an aggregation for null data packets.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We convert the mvm device to a PCI device and then back again when
trying to find the handle for the device's ACPI data. This is
unnecessary, so it can be removed.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support sending the DQA-enablement HCMD to the FW when
working in DQA mode.
This HCMD will enable DQA-specific flows in the FW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In DQA mode the AUX queue is mapped elsewhere than in non-
DQA mode. Update the code to reflect this.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the correct sta_id in the SCD_QUEUE_CONFIG command sent
to the FW when enabling/disabling queues. This is needed in
DQA-mode to allow the FW to associate between queue and STA.
In case the queue isn't connected to a specific station but
rather is a static "generic" queue - the sta_id should be
set to 0x10 (max supported STA is 0x0f).
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support DQA queue sharing when no free queue exists for
allocation to a STA that already exists. This means that
a single queue will serve more than a single TID (although
the RA will be the same for all TIDs served).
We try to choose the lowest AC possible, to ensure the
shared queues have the lowest possible combined AC
requirements. The queue to share is chosen only from the
same RA's DATA queues as follows (in descending priority):
1. An AC_BE queue
2. Same AC queue
3. Highest AC queue that is lower than new AC
4. Any existing AC (there always is at least 1 DATA queue)
If any aggregations existed for any of the TIDs of the
shared queue - they are stopped (the FW is notified), but
no delBA is sent.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
"max_amsdu_len" isn't set if kstrtouint() fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We never initialize ampdu_status so it causes a static checker warning
when we pass it to iwl_mvm_pass_packet_to_mac80211(). Fortunately, it's
never used so we can just remove it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some transports may sleep when writing to registers, which is done
when calling iwl_force_nmi(). So we can't call iwl_force_nmi() in a
timer context. To solve that, convert the scan timeout timer to a
delayed work.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Theoretically we may get only one IRQ from OS, in which
case we will have only 1 queue even in MSIx mode.
This will cause division by zero in the indirection table
calculation.
We do not need send the command in that case, as there is
only one queue so all RX traffic will be directed to it
anyway. Bail out early if there is only one queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently code calls restock for mq devices during the init
function, unlike sq where restock is called after init.
This causes an harmless but alarming deadlock warning from
lockdep, to fix this - unify the init code.
Rename the restock functions while at it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support marking queues as inactive upon a timeout expiring,
and allow inactive queues to be re-assigned to other RA/TIDs
if no other queue is free.
This is done by keeping a timestamp of the latest frame TXed
for every RA/TID, and then going over the queues currently in
use when a new queue is needed, inactivating all those that
are inactive.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of explicitly indicating the difference between just
DVM and MVM with an mvm_fw boolean change this to fw.type to
be more extensible and easier to understand.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since the values of this enum are used only internally,
we can let the compiler number them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8821ae_dm_watchdog() which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723e_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl8723be_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl92ee_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Flag rfchange_inprogress in struct rtl_ps_ctl is protected by a spinlock
in most routines but not in rtl88e_dm_watchdog(), which could
lead to a race condition. The necessary locking to prevent this condition
is added.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 4b9d8d67b4 ("rtlwifi: rtl8192cu: Remove unused parameter") reworked
this routine. Those changes were later reverted by commit d3feae41a3
("rtlwifi: Update power-save routines for 062814 driver").
There were two changes in commit 4b9d8d67b4. The first of these removed
a parameter from rtl_ps_set_rf_state() that was always false. This is the
change that is restored in the current patch. A second change that reworked
the locking is still being analyzed.
In addition to removing the unused parameter, there is no need for
rtl_ps_set_rf_state() to be exported.
Reported-by: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Pavel Andrianov <andrianov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sometimes MSIx interrupts are received out of order on multi-core
system. This creates a problem when there is a race between data
packet and SLEEP event from firmware. We will disable MSIx interrupt
mode to solve the problem and go with MSI mode.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit de3bb771f4 ("cfg80211: add more warnings for inconsistent
ops") the wireless core warns if a driver implements a cfg80211 callback
but doesn't implements the inverse operation.
The mwifiex driver defines a .set_antenna handler but not a .get_antenna
so this not only makes the core to print a warning when creating a new
wiphy but also the antenna isn't reported to user-space apps such as iw.
This patch queries the antenna to the firmware so is properly reported to
user-space. With this patch, the wireless core does not warn anymore and:
$ iw phy phy0 info | grep Antennas
Available Antennas: TX 0x3 RX 0x3
Configured Antennas: TX 0x3 RX 0x3
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
[javier: expand the commit message]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The mwifiex driver implements a cfg80211 .set_tx_power operation handler
but doesn't have the inverse .get_tx_power callback.
This not only has the effect that the Tx power can't be reported to user
space tools such as iwconfig and iwlist but also that the wireless core
prints a warning when a new wiphy is created due an cfg80211 operation
being implemented without its counterpart.
After this patch, the Tx power is properly reported to user-space tools:
$ iwlist mlan0 txpower
mlan0 unknown transmit-power information.
Current Tx-Power=13 dBm (19 mW)
and also the following warning isn't shown anymore on the driver probe:
WARNING: CPU: 3 PID: 127 at net/wireless/core.c:366 wiphy_new_nm+0x66c/0x6ac
Modules linked in: mwifiex_sdio mwifiex
CPU: 3 PID: 127 Comm: kworker/3:1 Tainted: G W 4.7.0-rc1-next-20160531-00006-g569df5b983f3
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events request_firmware_work_func
[<c010e1ac>] (unwind_backtrace) from [<c010af38>] (show_stack+0x10/0x14)
[<c010af38>] (show_stack) from [<c0323b9c>] (dump_stack+0x88/0x9c)
[<c0323b9c>] (dump_stack) from [<c011a828>] (__warn+0xe8/0x100)
[<c011a828>] (__warn) from [<c011a8f0>] (warn_slowpath_null+0x20/0x28)
[<c011a8f0>] (warn_slowpath_null) from [<c06a42d4>] (wiphy_new_nm+0x66c/0x6ac)
[<c06a42d4>] (wiphy_new_nm) from [<bf1c24cc>] (mwifiex_register_cfg80211+0x28/0x3f0 [mwifiex])
[<bf1c24cc>] (mwifiex_register_cfg80211 [mwifiex]) from [<bf1a0018>] (mwifiex_fw_dpc+0x2b0/0x474 [mwifiex])
[<bf1a0018>] (mwifiex_fw_dpc [mwifiex]) from [<c040eb74>] (request_firmware_work_func+0x30/0x58)
[<c040eb74>] (request_firmware_work_func) from [<c012fe90>] (process_one_work+0x124/0x338)
[<c012fe90>] (process_one_work) from [<c01300dc>] (worker_thread+0x38/0x4d4)
[<c01300dc>] (worker_thread) from [<c01353b8>] (kthread+0xdc/0xf4)
[<c01353b8>] (kthread) from [<c0107978>] (ret_from_fork+0x14/0x3c)
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The commit 7311ea8500 ("mwifiex: fix AP start problem for newly added
interface") attempted to fix an issue when a new AP interface is added.
But the patch didn't check the return value of the functions doing the
firmware calls and returned an error even if the functions didn't fail.
This prevents the network device to be registered properly, so fix it.
Fixes: 7311ea8500 ("mwifiex: fix AP start problem for newly added interface")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XZrY
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-01' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* More work on the RX path for the 9000 device series
* Some more dynamic queue allocation work
* A few bugfixes and other improvements
For some reason, the FRAME_RELEASE message handling for the
default queue ended up being in the only/default queue for
non-RSS devices; fix that and handle FRAME_RELEASE properly
on the default queue for RSS devices.
Fixes: 585a6fccf5 ("iwlwifi: mvm: infrastructure for frame-release message")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support CSA countdown offloading. When CSA starts, the driver
specifies the offsets to the eCSA and CSA IEs in the beacon template
command and the fw performs the countdown.
The fw notifies the driver when the channel switch flow
should be performed.
Beacon sent notifications are not used anymore.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a warning in case packet didn't end up in the HW
destined queue.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We now have 9000 devices that support multiple frames in
a single RB. Enable it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up without leading spaces here, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The function ar9003_hw_apply_minccapwr_thresh takes as second parameter not
a pointer to the channel but a boolean value describing whether the channel
is 2.4GHz or not. This broke (according to the origin commit) the ETSI
regulatory compliance on 5GHz channels.
Fixes: 3533bf6b15 ("ath9k: Fix regulatory compliance")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Just setting the proper return for reading beyond the eeprom data.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Found this obvious typo while going through the spectral
code design in ath10k
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Disable TX_STBC for both HT and VHT if the devices tx chainmask is '1'
TX_STBC is required only for devices with tx_chainmask > 1. This fixes
a ping failure for QCA9887 (1x1) in HT/VHT mode
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable beacon loss detection support for 10.4 by handling
roam event. With this change QCA99X0 station is able to
detect beacon loss when the AP is powered off
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Smatch warns about a number of cases in ath10k where a pointer is
null-checked after it has already been dereferenced, in code involving
ath10k private virtual interface pointers.
Fix these by making the dereference happen later.
Addresses the following smatch warnings:
drivers/net/wireless/ath/ath10k/mac.c:3651 ath10k_mac_txq_init() warn: variable dereferenced before check 'txq' (see line 3649)
drivers/net/wireless/ath/ath10k/mac.c:3664 ath10k_mac_txq_unref() warn: variable dereferenced before check 'txq' (see line 3659)
drivers/net/wireless/ath/ath10k/htt_tx.c:70 __ath10k_htt_tx_txq_recalc() warn: variable dereferenced before check 'txq->sta' (see line 52)
drivers/net/wireless/ath/ath10k/htt_tx.c:740 ath10k_htt_tx_get_vdev_id() warn: variable dereferenced before check 'cb->vif' (see line 736)
drivers/net/wireless/ath/ath10k/txrx.c:86 ath10k_txrx_tx_unref() warn: variable dereferenced before check 'txq' (see line 84)
drivers/net/wireless/ath/ath10k/wmi.c:1837 ath10k_wmi_op_gen_mgmt_tx() warn: variable dereferenced before check 'cb->vif' (see line 1825)
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The below warning message seems to hit occasionally with the following
combination (IPQ4019 + ACS scan) where we receive packets as a self peer
when hostapd does ACS when we bring up AP mode . ath10k has the below
fall back mechanism to fetch current operating channel in rx (it will
check for the next channel tracking variable if the current one is NULL)
[scan channel] --> [rx channel] --> [peer channel] -->
[vdev channel] --> [any vdev channel] --> [target oper channel]
'scan channel' and 'target operating channel' are directly fetched from
firmware events. All the others should be updated by mac80211.
During ACS scan we wouldn't have a valid channel context
assigned from mac80211 ('ar->rx_channel'), and also relying on
('ar->scan_channel') is not helpful (it becomes NULL when it goes to
BSS channel and also when the scan event is completed). In short we
cannot always rely on these two channel tracking variables.
'Target Operating Channel' (ar->tgt_oper_chan) seems to keep track of
the current operating even while we are doing ACS scan and etc. Hence
remove this un-necessary warning message and continue with
target_operating channel. At the worst case scenario when the target
operating channel is invalid (NULL) we already have an ath10k warning
message to notify we really don't have a proper channel configured in
rx to update the rx status("no channel configured; ignoring frame(s)!")
WARNING: CPU: 0 PID: 0 at ath/ath10k/htt_rx.c:803
[<c0318838>] (warn_slowpath_null) from [<bf4a0104>]
(ath10k_htt_rx_h_channel+0xe0/0x1b8 [ath10k_core])
[<bf4a0104>] (ath10k_htt_rx_h_channel [ath10k_core]) from
[<bf4a025c>] (ath10k_htt_rx_h_ppdu+0x80/0x288 [ath10k_core])
[<bf4a025c>] (ath10k_htt_rx_h_ppdu [ath10k_core]) from
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task+0x724/0x9d4 [ath10k_core])
[<bf4a1a9c>] (ath10k_htt_txrx_compl_task [ath10k_core])
Fixes:3b0499e9ce42 ("ath10k: reduce warning messages during rx without proper channel context")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Usually when the firmware crashes we check for the value
'FW_IND_EVENT_PENDING' in 'FW_INDICATOR_ADDRESS' and proceed with
disabling the irq and dumping firmware 'crash dump'. Now
when the PCI card is unplugged from the device the PCI controller
seems to generate a spurious interrupt after some time which
was as treated a firmware crash and resulting in the below race
condition (and eventually crashing the system)
ath10k_core_unregister -> ath10k_core_free_board_files
...... device unplug spurious interrupt .........
ath10k_pci_taklet -> ath10k_pci_fw_crashed_dump ...etc
Clearly even after the firmware board files related data structure
is freed up we are getting a spurious interrupt from PCI with 0xfffffff
in the 'FW_INDICATOR_ADDRESS' resulting in scheduling of the pci tasklet
and doing a crash dump, printing f/w board related info resulting in the
below crash. Fix this by detecting this spurious interrupt in ath10k PCI
irq handler itself and return IRQ_NONE. Thanks to Michal Kazior for
helping us conclude the most appropriate fix.
Call trace:
EIP is at ath10k_debug_print_board_info+0x39/0xb0
[ath10k_core]
EAX: 00000000 EBX: d4de15a0 ECX: 00000000 EDX: 00000064
ESI: f615ddd0 EDI: f8530000 EBP: f615de3c ESP: f615ddbc
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 80050033 CR2: 00000004 CR3: 01c0a000 CR4: 000006f0
Stack:
f615ddd0 00000064 f8b4ecdd 00000000 00000000 00412f4e
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
00000000 00000000 00000000 00000000 00000000 00000000
00000000 00000000
Call Trace:
[<f8b1f517>] ath10k_print_driver_info+0x17/0x30
[ath10k_core]
[<f875463a>] ath10k_pci_fw_crashed_dump+0x7a/0xe0
[ath10k_pci]
[<f87549d0>] ath10k_pci_tasklet+0x70/0x90 [ath10k_pci]
[<c106151e>] tasklet_action+0x9e/0xb0
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Registering wmediumd is currently limited to the initial network
namespace. This patch enables wmediumd to attach from non-initial
network namespaces using a user namespace having CAP_NET_ADMIN. A
registered wmediumd can forward frames on radios that have been created
in the same network namespace, even if they have been moved to other
network namespaces.
The wmediumd Netlink portid is tracked per net namespace. Additionally,
the portid is stored on all radios created in that net namespace to
simplify the portid lookup in the data path.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Since stations can now be added before association
(NL80211_FEATURE_FULL_AP_CLIENT_STATE support),
no supported rates are set when the station is added
to the fw, resulting in fw recovery.
Fix it by first configuring the AP basic rates as
the station configured rates (when the station is
first added to the driver), and after the station
was authorized re-configure it, now with the actual
supported rates.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We obviously don't want to fall through in that switch. With this change
1) We wait for event (triggered by p2p_disc) as expected
2) We remove interface manually on timeout
3) We return 0 on success instead of -ENOTSUPP
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This header provides two inline functions using struct brcmf_if so we
need core.h to avoid:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_prof’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:368:13: error: dereferencing pointer to incomplete type
return &ifp->vif->profile;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h: In function ‘ndev_to_vif’:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:374:12: error: dereferencing pointer to incomplete type
return ifp->vif;
^
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This function can work just fine with const pointer, it only calls
alloc_netdev which take const as well. Moreover it makes this function
more flexible as some cfg80211 callback may provide const char * as
well, e.g. add_virtual_intf. This will be needed for more advanced
interface management.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Removing P2P interface is handled by sending a proper request to the
firmware. On success firmware triggers an event and driver's handler
removes a matching interface.
However on event timeout we remove interface directly from the cfg80211
callback. Current code doesn't handle this case correctly as it always
assumes rtnl to be unlocked.
Fix it by adding an extra rtnl_locked parameter to functions and calling
unregister_netdevice when needed.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'inline' keyword to come before the return
type in a declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/intel/ipw2x00/ipw2200.c:4096:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Modern C standards expect the 'static' keyword to come first in a
declaration, and we get a warning for this with "make W=1":
drivers/net/wireless/broadcom/brcm80211/brcmsmac/main.c:3353:1: error: 'static' is not at beginning of declaration [-Werror=old-style-declaration]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
'register' is a keyword in C and cannot be used in place of a
variable name, as shown by this -Wextra warning:
drivers/net/wireless/cisco/airo.c:1105:29: error: 'register' is not at beginning of declaration [-Werror=old-style-declaration]
This replaces the 'register' keyword with a 'reg' identifier in
the declaration, which matches the definition and has the intended
meaning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that if interface type is changed from managed to
__ap, AP can be successfully started. But there is a problem if new
ap interface is added.
The problem got resolved after sending appropriate commands to firmware
in add_interface handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch populates secondary channel offset and downloads it to
firmware to fix the problem.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On some platforms, driver is unable to wakeup firmware after system resume
due to a problem at MMC subsystem. Triggering card reset in this case has
a race with card removal from MMC which causes system hang. This patch
resolves the problem by not triggering card reset.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is obeserved that sometimes scan operation will block the disconnect
during system suspend. It's ok to cancel ongoing scan in this case. It
reduces unnecessary system suspend delay.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch creates common function mwifiex_cancel_scan to remove
duplication of code.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When an association command is sent to firmware but the process is
killed before the command response arrives, driver will try to
access bss_desc which is already freed. This issue is fixed by
checking return value of bss_start.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.
realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
lbs_mac_event_disconnected may free priv->currenttxskb
while lbs_hard_start_xmit accesses to it.
The patch adds a spinlock for mutual exclusion.
Tested on OLPC XO-1 (usb8388) and XO-1.5 (sd8686) with v4.7-rc3.
Confirmed that lbs_mac_event_disconnected is being called on the
station when hostapd on access point is given SIGHUP.
Signed-off-by: Pavel <andrianov@ispras.ru>
Tested-by: James Cameron <quozl@laptop.org>
Acked-by: Vaishali Thakkar <vaishali.thakkar@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
pdev_data pointer is being freed with kfree but the pointer is not dynamic allocated.
Signed-off-by: Bruno Herrera <bruherrera@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use %*ph specifier to dump small buffers in hex format instead of doing this
byte-by-byte.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This also renames REG_USB_AGG_{TO,TH} to REG_USB_AGG_{TIMEOUT,THRESH}
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Documentation for enabling USB aggregation and whether to select
interrupt or bulk delivery of interrupt events.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
A dedicated workqueue has been used since the workitem (viz
&priv->cmd_work per priv, which maps to lbtf_cmd_work) is involved in
actual command processing and may be used on a memory reclaim path.
The workitems require forward progress under memory pressure and hence,
WQ_MEM_RECLAIM has been set. Since there are only a fixed number of work
items, explicit concurrency limit is unnecessary here.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This change reorders some operations in brcmf_setup_ifmodes in hope to
make it simpler:
1) It allocates arrays right before filling them. This way it's easier
to follow requested array length as it's immediately followed by
code filling it. It's easier to check e.g. why we need 4 entries for
P2P. Other than that it deduplicates some checks (e.g. for P2P).
2) It reorders code to first prepare limits and then define a new combo.
Previously this was mixed (e.g. we were setting num of channels
before preparing limits).
3) It modifies mbss code to use i variable just like other combos do.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRfMAAoJEG4XJFUm622bxwEH/iZm3o752MM62fJyCOEtEN6R
8vL7kyehX81G9szQyQ7bMQ7y0diobeBGsu8e7zzV4Mt+cU0Z9g/ezfca6HfE6Hrh
0ubKl/tSzAhRcAoQiNyKOI36yt455r1Mnr8a18OYO79pnNcjf7kSd7pJG2BW0Hdx
dRsSxzcg+E0w4z7mJ/cgM5aRzjXmXvAUjw9cIt36y3+ng1fQ+M782lkCtscMZY3Q
e5bkLCaP5TG+O9niPTjzrAzMlBTGwopknuEZnwIGDkNkx1PeBzRATVGeSa9Zba6d
g17kGbP7QT1GaCJF/FfWColaVpMBDhviovQANeoaUi804C4ZKNZAcJirZC3W2eM=
=uYcn
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers patches for 4.8
Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
brcmfmac
* add support for the PCIE devices 43525 and 43465
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXaRGeAAoJEG4XJFUm622bc6MH/jBpajTua8/fEUwo8dEywKRD
HULV6h5jDfoQ2N+LkKGff4UoAup4rWvzsXgTsNwPrma+TYi8M/eVrWanJ+TkwI31
2jHh2ynBqAPNhM6oT/NKJgGPgamFsa7mvtM8wBZV4VZseIGhJcKExExLjnE64ZdG
7o6VrtNRNtP+lnxT7ojbcS7cMnQqa7d32CqYjyJtABzLdSHNdww9euHLo9t6EFFa
7dti3t4WftTZ0+VyZmNrLgS+RO0ix7Kbr+ZfNQPyq9DLAaSfNZR8kWpNZjR7G4BA
QYffAkBO/iwffJS9b/VU+o8b32SV0TstTbJsEyvJcqkkTbngj2QhHZHBU012vQk=
=uVoM
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-06-21' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.7
iwlwifi
* fix the scan timeout for long scans
* fix an RCU splat caused when updating the TKIP key
* fix a potential NULL-derefence introduced recently
* fix a IGTK key bug that has existed since the MVM driver was introduced
* fix some fw capabilities checks that got accidentally inverted
rtl8xxxu
* fix typo on variable name
ath10k
* fix deadlock when peer cannot be created
* fix crash related to printing features
* fix deadlock while processing rx_in_ord_ind
ath9k
* fix GPIO mask regression for AR9462 and AR9565
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
ath.git patches for 4.8. Major changes:
ath10k
* enable btcoex support without restarting firmware
* enable ipq4019 support using AHB bus
* add QCA9887 chipset support
* retrieve calibration data from EEPROM, currently only for QCA9887
wil6210
* add pm_notify handling
Calling sdio_claim_host() from the interface independent part of
the mwifiex driver is not only a layering violation, but also causes
a link error if MMC support is disabled, or if CONFIG_MMC=m
and CONFIG_MWIFIEX=y:
drivers/net/built-in.o: In function `mwifiex_fw_dpc':
:(.text+0xff138): undefined reference to `sdio_claim_host'
:(.text+0xff158): undefined reference to `sdio_release_host'
The right way to do this is to have the sdio specific code in the
sdio driver front-end, and we already have a callback pointer that
we can use for this after exporting the generic fw download
function from the core driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 65c71efe1c ("mwifiex: fix racing condition when downloading firmware")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this including cfg80211.h in a wrong order could result in:
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:122:24: error: array type has incomplete element type
struct brcmf_wsec_key key[BRCMF_MAX_DEFAULT_KEYS];
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:291:24: error: field ‘p2p’ has incomplete type
struct brcmf_p2p_info p2p;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:297:27: error: field ‘pmk_list’ has incomplete type
struct brcmf_pmk_list_le pmk_list;
^
drivers/net/wireless/broadcom/brcm80211/brcmfmac/cfg80211.h:317:28: error: field ‘assoclist’ has incomplete type
struct brcmf_assoclist_le assoclist;
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This attribute was added 3 years ago by
commit 3eacf86655 ("brcmfmac: introduce brcmf_cfg80211_vif structure")
but it remains unused since then. It seems we can safely drop it.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Per Michael Büsch: "All a-phy code is usused", so remove it all.
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports the following error with -Werror=unused-const-variable.
drivers/net/wireless/broadcom/b43/phy_a.c:576:40: error:
'b43_phyops_a' defined but not used
Per Michael Büsch: "All a-phy code is usused", so remove it all,
and move the remaining Type-G initialization code into phy_g.c.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
alloc_workqueue replaces deprecated create_workqueue().
In if_sdio.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_sdio_host_to_card_worker.
The workitem is involved in sending packets to firmware.
Forward progress under memory pressure is a requirement here.
In if_spi.c, the workqueue card->workqueue has workitem
&card->packet_worker, which is mapped to if_spi_host_to_card_worker.
The workitem is involved in sending command packets from the host.
Forward progress under memory pressure is a requirement here.
Dedicated workqueues have been used in both cases since the workitems
on the workqueues are involved in normal device operation with
WQ_MEM_RECLAIM set to gurantee forward progress under memory pressure.
Since there are only a fixed number of work items, explicit concurrency
limit is unnecessary.
flush_workqueue is unnecessary since destroy_workqueue() itself calls
drain_workqueue() which flushes repeatedly till the workqueue
becomes empty. Hence the calls to flush_workqueue() before
destroy_workqueue() have been dropped.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus rx sequence is not in order because that control and event
frames always cause immediate send, but data frames may be held
for glomming in firmware side. It is not actually an error as the
packets are still processed even if the RX sequence is not in order.
Therefor the error message is rephrased and changed to a debug
message.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for the new PCIE devices 43525 and 43465.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using nmap tool with FMAC, the nmap packets were be dropped by kernel
because the size was too short. The kernel message showed like
"nmap: packet size is too short (42 <= 50)". It is caused by the packet
length is shorter than ndev->hard_header_len. According to definition of
LL_RESERVED_SPACE() and hard_header_len, we should use hard_header_len
to reserve for L2 header, like ethernet header(ETH_HLEN) in our case and
use needed_headroom for the additional headroom needed by hardware.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error message is given for something that is not an error here as
the drive strength configuration may not be applicable for specific
devices. Therefor the error message is rephrased and changed to a
debug message.
Signed-off-by: Wright Feng <wright.feng@broadcom.com>
[arend@broadcom.com: rephrase commit message]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SKBs can come with a prioriy. Currently a priority of 0..7 is
assumed. But this assumption is incorrect. To fix this any
priority of 0 or higher then 7 will be adjusted by calling
cfg80211_classify8021d
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Only hardcode the LED behavior if the SROM doesn't provide any for all
LEDs of the card. This avoids instantiating LED triggers for unconnected
LEDs, while (hopefully) keeping things working for old cards with a
blank SROM.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 reports:
drivers/net/wireless/marvell/libertas_tf/main.c:30:19: error:
'lbtf_driver_version' defined but not used
with -Werror=unused-const-variable=.
Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are nine copies of the _rtl88ee_read_adapter_info() function,
and most but not all of them cause a build warning in some configurations:
rtl8192de/hw.c: In function '_rtl92de_read_adapter_info':
rtl8192de/hw.c:1767:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
rtl8723ae/hw.c: In function '_rtl8723e_read_adapter_info.constprop':
rtlwifi/rtl8723ae/hw.c:1654:12: error: 'hwinfo' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem is that when rtlefuse->epromtype is something other than
EEPROM_BOOT_EFUSE, the rest of the function uses undefined data, resulting
in random behavior later.
Apparently, in some drivers, the problem was already found and fixed
but the fix did not make it into the others.
This picks one approach to deal with the problem and applies identical
code to all 9 files, to simplify the later consolidation of those.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two firmware events we handle similarly in brcmfmac:
BRCMF_E_LINK and BRCMF_E_IF. The difference from firmware point of view
is that the first one means BSS remains present in the firmware. Trying
to (re)create it (e.g. when adding new virtual interface) will result in
an error.
Current code treats both events in a similar way. It removes Linux
interface for each of them. It works OK with e.g. BCM43602. Its firmware
generates both events for each interface. It means we get BRCMF_E_LINK
and remove interface. That is soon followed by BRCMF_E_IF which means
BSS was also removed in a firmware. The only downside of this is a
harmless error like:
[ 208.643180] brcmfmac: brcmf_fweh_call_event_handler: no interface object
Unfortunately BCM4366 firmware doesn't automatically remove BSS and so
it doesn't generate BRCMF_E_IF. In such case we incorrectly remove Linux
interface on BRCMF_E_LINK as BSS is still present in the firmware. It
results in an error when trying to re-create virtual interface, e.g.:
> iw phy phy1 interface add wlan1-1 type __ap
[ 3602.929199] brcmfmac: brcmf_ap_add_vif: timeout occurred
command failed: I/O error (-5)
With this patch we don't remove Linux interface while firmware keeps
BSS. Thanks to this we keep a consistent states of host driver and
device firmware.
Further improvement should be to mark BSS as disabled and remove
interface on BRCMF_E_LINK. Then we should add support for reusing
BSS-es.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware for new chipsets is based on a new major version of code
internally maintained at Broadcom. E.g. brcmfmac4366b-pcie.bin (used for
BCM4366B1) is based on 10.10.69.3309 while brcmfmac43602-pcie.ap.bin was
based on 7.35.177.56.
Currently setting AP 5 GHz channel doesn't work reliably with BCM4366B1.
When setting e.g. 36 control channel with VHT80 (center channel 42)
firmware may randomly pick one of:
1) 52 control channel with 58 as center one
2) 100 control channel with 106 as center one
3) 116 control channel with 122 as center one
4) 149 control channel with 155 as center one
It seems new firmwares require setting AP mode (BRCMF_C_SET_AP) before
specifying a channel. Changing an order of firmware calls fixes the
problem. This requirement resulted in two separated "chanspec" calls,
one in AP code path and one in P2P path.
This fix was verified with BCM4366B1 and tested for regressions on
BCM43602.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 on x86 started warning about wl3501_get_encode when building
with -O2:
drivers/net/wireless/wl3501_cs.c: In function ‘wl3501_get_encode’:
drivers/net/wireless/wl3501_cs.c:1769:5: warning: ‘implemented’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1686:19: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1702:20: warning: ‘threshold’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1719:23: warning: ‘txpow’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1752:20: warning: ‘retry’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1806:25: warning: ‘pwr_state’ may be used uninitialized in this function
drivers/net/wireless/wl3501_cs.c:1383:24: warning: ‘value’ may be used uninitialized in this function
I could not figure out what exactly confuses gcc here, but splitting the
wl3501_get_mib_value function into two helps the compiler to figure out
that the variables are not actually used uninitialized, and makes it
slightly clearer to a human reader what the function actually does and
which parts of it are under the spinlock.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document lists the possible compatible strings that a SDIO child
node can have, so the driver checks if the defined in the node matches.
But the error message when that's not the case is misleading, so change
for one that makes clear what the error really is. Also, returning a -1
as errno code is not correct since that's -EPERM. A -EINVAL seems to be
a more appropriate one.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The Documentation/devicetree/bindings/net/wireless/marvell-sd8xxx.txt DT
binding document say that the "interrupts" property in the child node is
optional. So the property being missed shouldn't be treated as an error.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The function can fail so the returned value should be checked
and the error propagated to the caller in case of a failure.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's better to have the device name prefixed in the error message.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of duplicating part of the cleanups needed in case of an error
in .probe callback, have a single error path and use goto labels as is
common practice in the kernel.
This also has the nice side effect that the cleanup operations are made
in the inverse order of their counterparts, which was not the case for
the mwifiex_add_card() error path.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There's only a check if mwifiex_add_card() returned a nonzero value, but
the actual error code is neither stored nor propagated to the caller. So
instead of always returning -1 (which is -EPERM and not a suitable errno
code in this case), propagate the value returned by mwifiex_add_card().
Patch also removes the assignment of sdio_disable_func() returned value
since it was overwritten anyways and what matters is to know the error
value returned by the first function that failed.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the sdio_enable_func() function fails on .probe, the -EIO errno code
is always returned but that could make more difficult to debug and find
the cause of why the function actually failed.
Since the driver/device core prints the value returned by .probe in its
error message propagate what was returned by sdio_enable_func() at fail.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SDIO is an auto enumerable bus so the SDIO devices are matched using the
sdio_device_id table and not using compatible strings from a OF id table.
However, commit ce4f6f0c35 ("mwifiex: add platform specific wakeup
interrupt support") allowed to match nodes defined as child of the SDIO
host controller in the probe function using a compatible string to setup
platform specific parameters in the DT.
The problem is that the OF parse function is always called regardless if
the SDIO dev has an OF node associated or not, and prints an error if it
is not found. So, on a platform that doesn't have a node for a SDIO dev,
the following misleading error message will be printed:
[ 12.480042] mwifiex_sdio mmc2:0001:1: sdio platform data not available
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is helpful for debugging. Without this all I was getting from "iw"
command on failed creating of P2P interface was:
> command failed: Too many open files in system (-23)
Signed-off-by: Rafal Milecki <zajec5@gmail.com>
[arend@broadcom.com: reduce error prints upon iface creation]
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath.git fixes for 4.7. Major changes:
ath9k
* fix GPIO mask regression with AR9462 and AR9565
ath10k
* fix deadlock while processing rx_in_ord_ind
* fix crash related to printing firmware features in debug mode
* fix deadlock when peer cannot be created
path_b_ok is being assigned but immediately after path_a_ok is being
compared to the value 0x03. This appears to be a typo on the
variable name, compare path_b_ok instead.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch ensures that 'locally_generated' parameter is correctly
passed to cfg80211_disconnected() API.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The GFP_DMA flag is obviously misunderstood in the mwifiex driver. It's
meant for legacy ISA DMA memory mappings only -- the lower 16MB on x86.
That doesn't apply to PCIe or SDIO devices, I guess.
Remove the GFP_DMA flag to reduce the need to place the socket buffer
allocation into the low mem DMA area, which might already be in use by
other drivers.
This misuse was flagged by the PaX USERCOPY feature by chance, as it
detected the user copy operation from a DMA buffer in the recvfrom()
syscall path.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Tested-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Cc: Nishant Sarmukadam <nishants@marvell.com>
Cc: Xinming Hu <huxm@marvell.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Brad Spengler <spender@grsecurity.net>
Cc: PaX Team <pageexec@freemail.hu>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is important for brcmfmac as some of released firmwares (e.g.
brcmfmac4366b-pcie.bin) may pick different channel than requested. This
has been tested with BCM4366B1 in D-Link DIR-885L.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Our d11 code supports encoding/decoding channel info into/from chanspec
format used by firmware. Current implementation is quite misleading
because of the way "chnum" field is used.
When encoding channel info, "chnum" has to be filled by a caller with
*center* channel number. However when decoding chanspec the same field
is filled with a *control* channel number.
1) This can be confusing. It's expected for information to be the same
after encoding and decoding.
2) It doesn't allow accessing all info when decoding. Some functions may
need to know both channel numbers, e.g. cfg80211 callback getting
current channel.
Solve this by adding a separated field for control channel.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gcc-6 warns about code in il3945_hw_txq_ctx_free() being
somewhat ambiguous:
drivers/net/wireless/intel/iwlegacy/3945.c:1022:5: warning: suggest explicit braces to avoid ambiguous 'else' [-Wparentheses]
This adds a set of curly braces to avoid the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The action 'check for winner' and 'download firmware' should be an
atomic action. This is true for btmrvl driver but not mwmfiex, which
cause firmware download to fail when the following senerio happens:
1) mwifiex check winner status: true
2) btmrvl check winner status: true, and start downloading firmware
3) mwfieix tries to download firmware, but failed because btmrvl is
already downloading.
This won't happen if 1) and 3) is an atomic action. This patch adds
sdio_claim/release_host call around those two actions to make sure it's
atomic.
Signed-off-by: Wei-Ning Huang <wnhuang@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simplify assignment in wlc_phy_rxcal_gainctrl_nphy_rev5.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Simplify _rtl92ee_phy_path_adda_on.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not dereference card before checking against NULL value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not return undefined value for transmission power
if the rate is invalid.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable adapter is incorrectly initialized.
Fixes: bf00dc22bc ("mwifiex: AMSDU Rx frame handling in AP mode")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
msg is dereferenced before checking against NULL, e.g.
when assigning pad_bytes.
Remove the superfluous check in function rsi_mgmt_pkt_to_core.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The nl80211 layer expects P2P search operation to be aborted
if needed when stopping P2P device. If the P2P search operation
is still running after returning from stop_p2p_device
it causes a WARN_ON and possibly a kernel crash.
Fix this by aborting the P2P search in wil_cfg80211_stop_p2p_device
and preventing P2P search from being started on a stopped P2P
device.
Note, the fix does not cover the case where a regular scan
is started on the P2P device. It will be completed in the
future when support is added for aborting a scan operation.
Signed-off-by: Lior David <qca_liord@qca.qualcomm.com>
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In wil_p2p_listen chan is checked to protect against NULL
pointer access only before setting channel = chan->hw_value.
Add a global parameter check to cover all accesses to chan.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In this switch statement, the default case does not always assign
sifs. In practice, ah->ah_bwmode cannot take values besides the
other labels, so this is not an actual problem, but it looks odd
and smatch complains thus:
ath5k_hw_get_default_sifs() warn: missing break? reassigning 'sifs'
Silence the warning by moving default label up a line.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
commit 5c86d97bcc ("ath10k: combine txrx and replenish task")
introduced deadlock while processing rx in order indication message
for qca6174 based devices. While merging replenish and txrx tasklets,
replenish task should be called out of htt rx ring locking since it
is also try to acquire the same lock.
Unfortunately this issue is not exposed by other solutions (qca988x,
qca99x0 & qca4019), as rx_in_ord_ind message is specific to qca6174
based devices. This patch fixes
=============================================
[ INFO: possible recursive locking detected ]
4.7.0-rc2-wt-ath+ #1353 Tainted: G E
---------------------------------------------
swapper/3/0 is trying to acquire lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d7ef19>]
ath10k_htt_rx_msdu_buff_replenish+0x29/0x90 [ath10k_core]
but task is already holding lock:
(&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(&(&htt->rx_ring.lock)->rlock);
lock(&(&htt->rx_ring.lock)->rlock);
*** DEADLOCK ***
May be due to missing lock nesting notation
1 lock held by swapper/3/0:
#0: (&(&htt->rx_ring.lock)->rlock){+.-...}, at: [<f8d82cab>]
ath10k_htt_txrx_compl_task+0x21b/0x250 [ath10k_core]
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=119151
Fixes: 5c86d97bcc ("ath10k: combine txrx and replenish task")
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In QCA4019, cycle counter wraparound is not tied to rx
clear counter. Each counter would wraparound individually
and after wraparound the respective counter will be reset
to 0x7fffffff while other counter still running unaffected.
Define a new wraparound type for this behaviour and handle
it separately so that rx clear counter wraparound is also
handled just like cycle counter. With this type of
wraparound we can accurately compute and report channel
active/busy time when any of the counter overflows.
Fixes: ee9ca147c5 ("ath10k: Fix survey reporting with QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA988X hw implements a different cycle counter wraparound
behaviour when compared to QCA4019. To properly handle different
wraparound logic for these chipsets replace already available
bool hw_params member, has_shifted_cc_wraparound, with an
enum which could be extended to handle different wraparound
behaviour. This patch keeps the existing logic functionally
same and a prepares cycle counter wraparound handling to
extend for other chips.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
[kvalo@qca.qualcomm.com: change also QCA9887 wrap type]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
CCK hardware table mapping from QCA99X0 onwards got revised.
The CCK hardware rate values are in a proper order wrt. to
rate and preamble as below
ATH10K_HW_RATE_REV2_CCK_LP_1M = 1,
ATH10K_HW_RATE_REV2_CCK_LP_2M = 2,
ATH10K_HW_RATE_REV2_CCK_LP_5_5M = 3,
ATH10K_HW_RATE_REV2_CCK_LP_11M = 4,
ATH10K_HW_RATE_REV2_CCK_SP_2M = 5,
ATH10K_HW_RATE_REV2_CCK_SP_5_5M = 6,
ATH10K_HW_RATE_REV2_CCK_SP_11M = 7,
This results in reporting of rx frames (with CCK rates)
totally wrong for QCA99X0, QCA4019. Fix this by having
separate CCK rate table for these chipsets with rev2 suffix
and registering the correct rate mapping to mac80211 based on
the new hw_param (introduced) 'cck_rate_map_rev2' which shall
be true for any newchipsets from QCA99X0 onwards
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
All these flags are not used and their use is completely
covered by 'ath10k_hw_rate_ofdm', 'ath10k_hw_rate_cck',
and RX_PPDU_START_RATE_FLAG
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Only five bits are defined to pass tid information in HTT_RX_IND
message, so the mask which can be used to extract tid should be 0x1f
instead of the current 0x3f. Also, macros which can be used to extract
flush_valid and release_valid bits have to be left shifted one bit less
because these information follow the tid right after. This patch does
not really fix anything functionally because these macros are not used
currently.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
-----BEGIN PGP SIGNATURE-----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=FvhQ
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2016-06-09' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
For the next cycle, we have the following:
* the biggest change is Michał's work on integrating FQ/codel
with the mac80211 internal software queues
* cfg80211 connect result gets clarified for the
"no connection at all" case
* advertisement of per-interface type capabilities, in case
they differ (which makes a lot of sense for some capabilities)
* most of the nl80211 & hwsim unprivileged namespace operation
changes
* human-readable VHT capabilities in debugfs
* some other cleanups, like spelling
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
My cleanup in "iwlwifi: prepare for higher API/CAPA bits" accidentally
inverted a few tests - fix them.
Fixes: 859d914c8f ("iwlwifi: prepare for higher API/CAPA bits")
Reported-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW expect the driver to set the encryption algorithm type when
installing the IGTK key in the HW.
Currently when installing CMAC IGTK key we don't set the algorithm type
and as a result the FW fails to calculate the MIC of multicast management
frames.
Fix it.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We try to access sta before we check for IS_ERR_OR_NULL(), so we may
end up accessing a NULL pointer. To prevent that, move the conversion
from sta to mvm_sta below the check.
Fixes: b915c10174 ("iwlwifi: mvm: add reorder buffer per queue")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 16 seconds timeout we were using turned out to be too short.
Recalculations by system show that the total time in both bands should
be < 18.5 seconds, even in the slowest cases (e.g. DCM P2P with
DTIM=2). Rounding it up to 20 seconds for a bit more safety.
Fixes: 728e825f81 ("iwlwifi: mvm: add a scan timeout for regular scans")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The old implementation was overcomplicated and slightly bugged in some
corner cases.
Consider following state of BSS-es (limited to 6 for simplification):
drvr->iflist[0]: { bsscfgidx:0, ndev->name:wlan1, }
drvr->iflist[1]: (null)
drvr->iflist[2]: { bsscfgidx:2, ndev->name:wlan1-1, }
drvr->iflist[3]: { bsscfgidx:3, ndev->name:wlan1-2, }
drvr->iflist[4]: (null)
drvr->iflist[5]: (null)
In such case the next AP interface should bsscfgidx 4 (we don't use 1 as
it's reserved for P2P).
With old code the loop iterations were following:
[ifidx = 0] [bsscfgidx = 2] [highest = 2]
[ifidx = 1] [bsscfgidx = 2] [highest = 2] available = true
[ifidx = 2] [bsscfgidx = 2] [highest = 2] bsscfgidx = highest + 1
[ifidx = 3] [bsscfgidx = 3] [highest = 2] bsscfgidx = highest + 1
[ifidx = 4] [bsscfgidx = 3] [highest = 2] available = true
[ifidx = 5] [bsscfgidx = 3] [highest = 2] available = true
There were 2 obvious problems:
1) Having empty BSS at index 1 was resulting in available being always
set to true, even if we would run out of BSS-es.
2) Calculated bsscfgidx was invalid (3 instead of 4) resulting in driver
not being able to create the 4th AP interface.
New code is simpler, placed in file where it's really used, handles
running out of free BSS-es and allows using 4 interfaces at the same
time. It also looks for the first free BSS instead of one after the last
in use. It works well with current driver (which doesn't allow deleting
interfaces) and should be future proof (if we ever allow deleting).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This looks like a regression from commit c4cdf753ed ("ath10k: move
fw_features to struct ath10k_fw_file"), we were printing the features from a
wrong struct.
Fixes: c4cdf753ed ("ath10k: move fw_features to struct ath10k_fw_file")
Signed-off-by: Ben Greear <greearb@candelatech.com>
[kvalo@qca.qualcomm.com: improve commit log]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The QCA9887 stores its calibration data (board.bin) inside the EEPROM of
the target. This has to be downloaded manually to allow the device to
initialize correctly.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: handle -EOPNOTSUPP and s/fetch_board_data/fetch_cal_eeprom]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the hardware name, revision, firmware names and update the pci_id
table.
QA9887 HW1.0 is supposed to be similar to QCA988X HW2.0 . Details about
he firmware interface are currently unknown.
Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
[kvalo@qca.qualcomm.com: add a warning about experimental support]
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
brcmfmac
* add fallback RSSI report for devices that do not report per-chain values
* fix a null pointer derefence regression on PCIe full dongle devices
rtlwifi
* fix scheduling while atomic regression from commit 49f86ec21c
MAINTAINERS
* add file patterns for wireless device tree bindings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXUvUsAAoJEG4XJFUm622bdKAH/R2UKYx3t73llbqlpgkSCOxZ
wRMleoRZRF8DI9lT4QUxGCq5wxED0U2TtDJh7LJJ9I5sAY1n50w+e2TTZ5r6ftXo
1J79NvvrbVM8227shburpveyxzeQkLtI+DDkP07nMtF3VNxOrU9+z3TPM27QR1LM
0pq/yrKZ7Qnrf9gf4oTeH0dQKYmA4Om/HXjnMU4Sxi/vhKQBfcemjHacv37BTG/F
4PrFzC17O7wVFDeKKXXieK1Z9inpocZMG9OceHXxi9fwrT+RhMnJdrDarSi4b92W
m1yiRcS0389R/jEG3O2LRVNIJVnBHdQmEU8Bg8nup377sFxX/weWVYagaX4f2bE=
=AObt
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-for-davem-2016-06-04' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.7
brcmfmac
* add fallback RSSI report for devices that do not report per-chain values
* fix a null pointer derefence regression on PCIe full dongle devices
rtlwifi
* fix scheduling while atomic regression from commit 49f86ec21c
MAINTAINERS
* add file patterns for wireless device tree bindings
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Check the current PHY operating mode (gmode) to see if we should
fall back from 6MB OFDM to 11MB CCK. For 5GHz operation this isn't
allowed.
Note, the fallback lookup is only done for RTS rates; normal fallback
rates are done via mac80211 and aren't affected by this change.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_sdiod_intr_unregister call that removes both func1 and
func2 interrupt handlers only called when brcmf_ops_sdio_remove
is called for func 1 (which is the 2nd call) but sdio is expecting
it to be removed at the end of each sdio_remove call.
This is causing 'rmmod bcmrfmac' on a 4356-sdio chip to complain
with:
WARNING: driver brcmfmac did not remove its interrupt handler!
The modification makes calling brcmf_sdiod_intr_unregister multiple
times harmless by clearing the variables that track if interrupt
handlers have been installed, and then calls it on every
brcmf_ops_sdio_remove call instead of just remove for func 1.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When chip attach fails, brcmf_sdiod_intr_unregister is being called
but that is too early as sdiodev->settings has not been set yet
nor has brcmf_sdiod_intr_register been called.
Change to use oob_irq_requested + newly created sd_irq_requested
to decide on what to unregister at intr_unregister time.
Steps to reproduce problem:
- modprobe brcmfmac using buggy FW
- rmmod brcmfmac
- modprobe brcmfmac again.
If done with a buggy firmware, brcm_chip_attach will fail on the
2nd modprobe triggering the call to intr_unregister and the
kernel oops when attempting to de-reference sdiodev->settings->bus.sdio
which has not yet been set.
Signed-off-by: Christian Daudt <csd@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The previous text was confusing, leading readers to think this
driver was a duplicate, and so didn't need to be enabled.
After the removal of the older staging driver, this is the only
driver in mainline for these devices.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All the necessary patches to make wifi running (over AHB)
on ipq4019 SoC are ready now. It's good to enable
ipq4019 wifi device probing in ahb module and
remove work in progress debug print.
Device tree change is there in the public review by
below commit message
"qcom: ipq4019: add wifi nodes to ipq4019 SoC device tree"
Signed-off-by: Tamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 firmware has support to enable or disable btcoex functionality
without reloading firmware via wmi pdev param. Add provision to send
pdev param command via existing btcoex knob.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This feature flag will be used for firmware to support BT-Coex feature
without reloading firmware via WMI pdev param. To support Bluetooth
coexistence pdev param, WMI_COEX_GPIO_SUPPORT of extended resource
config should be enabled always. This firmware IE is used to configure
WMI_COEX_GPIO_SUPPORT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Update module description to advertise all supported QCA 802.11ac devices.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Remove unused inline function phy_mode_to_band.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Earlier when operating irq mode is legacy, interrupts are disabled
and re-enabled based on num_msi_intrs. commit cfe9011a05 ("ath10k:
remove MSI range support") replaced num_msi_intrs by oper_irq_mode.
Since oper_irq_mode is not initialized for ahb devices (i.e qca4019),
device boot up is failed during probe.
Fixes: cfe9011a05 ("ath10k: remove MSI range support")
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix invalid argument error while writing 'simulate_fw_crash',
though the funcionality is working fine we get an error 'invalid
argument' because 'count' value is not returned properly
(no reason to reduce the count value for removing the newline)
Fixes the below write error:
/sys/kernel/debug/ieee80211/phy0/ath10k# echo hw-restart >
simulate_fw_crash
-bash: echo: write error: Invalid argument
Also move the 'conf_mutex' as it is really not required for
fetching the userspace buffer.
Reported-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
diag_read uses dma_alloc_coherent to allocate memory requested by the
caller. If this memory requested is larger, more than DIAG_TRANSFER_LIMIT
(2K), then it is likely that we may not get the requested memory and we
would fail.
To solve this, request dma_alloc_coherent for only DIAG_TRANSFER_LIMIT, and
reuse this buffer multiple times as needed to copy the data requested in
smaller chunks of size not more than DIAG_TRANSFER_LIMIT. Previously we
were reading into the caller's only after getting the complete requested
data.
Fixes: 68c03249f3 ('ath10k: convert pci_alloc_consistent() to dma_alloc_coherent()')
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
A wmediumd that does not send this attribute causes a NULL pointer
dereference, as the attribute is accessed even if it does not exist.
The attribute was required but never checked ever since userspace frame
forwarding has been introduced. The issue gets more problematic once we
allow wmediumd registration from user namespaces.
Cc: stable@vger.kernel.org
Fixes: 7882513bac ("mac80211_hwsim driver support userspace frame tx/rx")
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
While wiphys can be moved into network namespaces over nl80211, the
creation and removal of hwsim radios is currently limited to the initial
namespace. This patch allows management of namespaced radios from the
owning namespace by setting genetlink netnsok.
To prevent two arbitrary namespaces to communicate over the simulated
shared medium, radios are separated by netgroups. Each radio created in
the same namespace lives in the same netgroup and hence can communicate
with other radios in that group. When moving radios to other namespaces,
the netgroup is preserved, so two radios having the same netgroup can
communicate even if not in the same namespace; This allows a controlling
namespace to create radios and move them to other namespaces for
communication.
When a net namespace owning a radio exits, the radio is destroyed unless
it was created in the initial network namespace. This keeps the previous
behavior by returning them to the init namespace, but prevents unprivileged
users from creating radios in the initial namespace.
Signed-off-by: Martin Willi <martin@strongswan.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On TX99 mode, instead of assuming interrupt mask non ATH9K_INT_GLOBAL,
let ath9k_hw_disable_interrupts proper set interrupt ref count.
This prevents some PCI PERR occurring specialy when setting 11b and n rates.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Change the implementation of wil log functions for consistency
with __wil_dbg_ratelimited.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Adding pm_notify to allow the following:
1. Check if suspend is allowed in an earlier stage to prevent
starting the suspend procedure in case it is not allowed
2. Notify the platform driver on the suspend request
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In case we fail to map one of the TSO SKB fragments, we need to
clear all the mapped descriptors, from swhead to swhead+descs_used-1.
Change the desc index calculation to
i = (swhead + descs_used - 1) % vring->size;
to prevent unmpping of (swhead + descs_used) descriptor that wasn't
mapped.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
napi_synchronize is called before releasing the vring, with the
assumption that setting txdata->enabled to 0 will prevent handling
of this vring in the next scheduled napi.
To guarantee this assumption, a memory barrier is added after disabling
the txdata.
In addition, as the ctx is zeroed in wil_tx_complete after this
descriptor is handled (protected by wmb), ctx needs to be checked
before releasing this descriptor in wil_vring_free.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
add memory barrier after allocating new rx descriptors, before
updating the hwtail.
This will guarantee that all writes to descriptors (shared memory)
are done before committing them to HW.
Signed-off-by: Maya Erez <qca_merez@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
