When an NL80211_DISCONNECT is sent to cfg80211, the driver's cfg80211
disconnect function sets the sme_state to SME_DISCONNECTED before receiving
a WMI_DISCONNECT_EVENT from the firmware. This caused cfg80211 to not know
that the connection is disconnected because the driver fails to notify
cfg80211 upon receiving WMI_DISCONNECT_EVENT from the firmware believing
it is already disconnected.
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When disabling tethering after having enabled it, the ath6kl driver does
not set the IFF_LOWER_UP flag to 0 (carrier off) on the wlan interface.
The upper layers (eg. connman) are not notified of the tethering mode
status change. So, tethering can not be activated anymore.
This patch adds a netif_carrier_off() call when stopping AP mode to fix
the problem.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
One minute after a successful connection, the kernel checks if the
frequency and the channel width are well configured for the country we
are in. (regulatory domain)
ath6kl driver was setting the NL80211_CHAN_HT20 channel without checking
for the HT capabilities. (we should have NL80211_CHAN_NO_HT in our
case because the firmware did not support HT)
This patch adds a check on ht_cap.ht_supported in order to create the
channel corresponding to the firmware capabilities.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When enabling WLAN tethering, a new AP is visible and a STA could
connect to it. When the STA tries to authenticate to the newly created
AP, the WPA authentication mechanism is stuck in the 1/4 msg of 4-Way
Handshake.
In ath6kl_rx(), the ath6kl_find_sta() function is looking for the
h_source field of the Ethernet frame header received by the STA. The
datap pointer that points to the Ethernet frame header is incorrect,
and was pointing at the wrong offset in the buffer.
This commit adds a pad_before_data_start offset to set the datap pointer
to the Ethernet frame header. datap->h_source parameter is now really
pointing to the source ethernet address and the authentication process
can continue.
Signed-off-by: Pierre Le Magourou <plemagourou@aldebaran.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Ideally wake_tx_queue should be used regardless as
it is a requirement for reducing bufferbloat and
implementing airtime fairness in the future.
However some setups (typically low-end platforms
hosting QCA988X) suffer performance regressions
with the current wake_tx_queue implementation.
Therefore disable it unless it is really
beneficial with current codebase (which is when
firmware supports smart pull-push tx scheduling).
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Same skb is being reused for storing command response from firmware
in PCIe chipsets. There was a bug while updating the skb length.
This patch ensures skb length correctly gets updated based on rx_len.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In corner case, we may end up processing same interrupt twice.
We have a logic to read pending interrupts at the end of interrupt
processing routine. It has a race with interrupts read in interrupt
handler. This patch solves the problem by ORing the interrupt bitmap
in this case.
The symptom for this bug is below messages in dmesg log.
[ 11.522123] mwifiex_pcie 0000:01:00.0: CMD_RESP: invalid cmd resp
[ 11.680412] mwifiex_pcie 0000:01:00.0: There is no command but got cmdrsp
Link: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It's been observed that request_irq() failure leads to a system crash
due to a bug in mwifiex driver.
When this failure happens, mwifiex_add_card() already takes care of
clearing and freeing adapter->card pointer. This patch removes the
redundant cleanup code causing crash.
Signed-off-by: Karthik D A <karthida@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The sdio dpc starts processing when in SDIOD_STATE_DATA. This state was
entered right after firmware download. This patch moves that transition
just before enabling sdio interrupt handling thus avoiding watchdog
expiry which would put the bus to sleep while probing.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the host-interface bus has hard time handling transmit packets
it informs higher layer about this and it would stop the netdev
queue when needed. However, since commit 9cd18359d3 ("brcmfmac:
Make FWS queueing configurable.") this was broken. With this patch
the behaviour is restored.
Cc: stable@vger.kernel.org # v4.5, v4.6, v4.7
Fixes: 9cd18359d3 ("brcmfmac: Make FWS queueing configurable.")
Tested-by: Per Förlin <per.forlin@gmail.com>
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
memory is malloced in mwifiex_cfg80211_start_ap() and should be
freed before leaving from the error handling cases, otherwise it
will cause memory leak.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes the following sparse warning:
drivers/net/wireless/marvell/libertas/cfg.c:2047:5: warning:
symbol 'lbs_set_power_mgmt' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Adding this opcode, allows the TI wireless driver,
to report throughput directly from FW to mac80211.
This is used mainly for mesh metric calculation.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
[kvalo@codeaurora.org: fix indentation]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW will provide a TX rate per link for each FW status,
and wlcore will be able to store the information for
the use of the mesh hwmp module.
This is used mainly in mesh.
Rates are reported when a mesh interface is up.
Signed-off-by: Maxim Altshul <maxim.altshul@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This was succesfully tested with 4366B1. A small workaround is needed
for the main interface otherwise it would stuck at the hidden state.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
1. Added support for interface and role of mesh type.
2. Enabled enable/start of mesh-point role,
and opening and closing a connection with a mesh peer.
3. Added multirole combination of mesh and ap
under the same limits of dual ap mode.
4. Add support for 'sta_rc_update' opcode for mesh IF.
The 'sta_rc_update' opcode is being used in mesh_plink.c.
Add support in wlcore to handle this opcode correctly for mesh
(as opposed to current implementation that handles STA only).
5. Bumped the firmware version to support new Mesh functionality
Signed-off-by: Maital Hahn <maitalm@ti.com>
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For multiple REG Host Commands (e.g HostCmd_CMD_802_11_EEPROM_ACCESS,
HostCmd_CMD_MAC_REG_ACCESS etc.) "cpu_to_leX"-converted values are
saved to driver. So, "leX_to_cpu" conversion is required too many
times afterwards in driver.
This patch reduces the endian: conversion without saving "cpu_to_leX"
converted values in driver. This will convert endianness in prepare
command and command response path.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJXhmR1AAoJEG4XJFUm622bn+gH/Ar5l/oU76nmXKh0xNiV6bUE
2FuRV9X7ynAOLbFJfqZvN8eL1kTyztXOpxVOt9xLZvNcrJP2mdOH+YdUpSPk/XRw
mpFC7RCln/Y1bbX02la7V8iRJlKK1/VmdMABJXsalDcxSPMhhBQtr4/ZC7NcgmeJ
zKCZDGr/x4qpmAkYGsf3msJsBotHtt9xuHp4fFswp9Gpm+VeqtdqGEeMxowoILRK
QBj6nZIuLI4PMnJhfCJn94t9D/AVUIVJTeuWNDS5Up4gZVFo9SlpnkR520P0IY4Q
1238g5sAdKqONsPO0lyUacUlY2cTafDr4kD6UKnjf659KDd49MDJArpfbvMeweY=
=PTV+
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-07-13' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.8
Major changes:
iwlwifi
* more work on the RX path for the 9000 device series
* some more dynamic queue allocation work
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
mwifiex
* implement get_tx_power and get_antenna cfg80211 operation callbacks
wl18xx
* add support for 64bit clock
rtl8xxxu
* aggregation support (optional for now)
Also wireless-drivers is merged to fix some conflicts.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The iwl-debug.h header relies in implicit inclusion of linux/device.h and
we get a lot of warnings without that:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:23: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.h:66:0,
from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:68:
drivers/net/wireless/intel/iwlwifi/iwl-trans.h: In function 'iwl_trans_tx':
drivers/net/wireless/intel/iwlwifi/iwl-trans.h:1030:348: error: passing argument 1 of '__iwl_err' from incompatible pointer type [-Werror=incompatible-pointer-types]
IWL_ERR(trans, "%s bad state = %d\n", __func__, trans->state);
^
In file included from drivers/net/wireless/intel/iwlwifi/iwl-eeprom-read.c:67:0:
drivers/net/wireless/intel/iwlwifi/iwl-debug.h:44:6: note: expected 'struct device *' but argument is of type 'struct device *'
void __iwl_err(struct device *dev, bool rfkill_prefix, bool only_trace,
^~~~~~~~~
The easiest workaround is to just declare 'struct device' before its first use,
rather than including the entire header file.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 21cb3222fe ("iwlwifi: decouple PCIe transport from mac80211")
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As hw cycle counters in QCA4019 wraparound independantly in QCA4019
it is possible cycle counter and rx clear counter would wraparound
at the same time. Current logic assumes only one of the counters
would wraparound at anytime. Fix this by moving 'else' part to
another 'if'.
Fixes: 8e100354a9 ("ath10k: fix cycle counter wraparound handling for QCA4019")
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes the firmware sends a HAL_DEL_BA_IND, the prima driver silently
ignore this message so let's do the same to silence the error message.
Cc: Nicolas Dechesne <nicolas.dechesne@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch fixes some issues with interface reconfiguration. It could
for example happen that an AP interface in beacon slot 0 was removed
leaving an IBSS station in one of the other slots. When this happens
the driver never sends out the beacon as it only tries to send a beacon
from slot 0.
Appart from that the tracking of required changes to the beacon config is
relatively complicated and prone to errors.
The approach taken here is to solve reconfiguration issues is to
reconfigure the beacons when any interface changes. This means that
the complexity of deciding whether an interface change may modify the
beacon configuration is gone. It also means that the beacon config will
be reliably updated when an interface is removed.
The issue that a single non-AP interface might not be in beacon
slot 0 and wouldn't be send out is solved by moving it into the
first slot. The TSF value in hardware is adjusted accordingly so
that the timestamp of the beacons stay consistent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The removed ATH9K_SLOT_TIME_X constants simply map the value in microseconds
to the same integer. These constants were not used consistently, so fix the
inconsistency issue by replacing all occurances with the integer equivalent.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k driver modifies the TSF for VIFs for the purpose of sending
beacons in a staggered fashion. This patch exposes this VIF specific
adjustment of the TSF value to mac80211. Without the change the TSF
routines handle the hardware TSF value instead of the actual TSF value as
seen on the air.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
These changes make ath9k_hw_reset more consistent with other places that
handle the TSF value by using the same helper routine.
A slight improvement is to not assume that a fixed time of 1.5ms has
passed for the initval writes when compared to the first write attempt.
Instead the TSF value is re-calculated which will yield a higher accuracy
of the restored TSF timer.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The ath9k TSF handling routines need to be aware of the channel context that
is being modified. With this change the TSF related values that are stored
in each channel context will be correctly tracked and the harware will only
be updated if the modified context is currently the active one.
Without this change the TSF modifications done using these routines would
for example be lost during a hardware reset as done by ath_complete_reset.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Beacons were not send out at (timestamp % beacon_time == 0) for interfaces
other than the primary one. To send out beacons with the correct timestamp
according to 10.1.3.2 of the 802.11 standard the tsf_adjustment has to be
set to the negative time difference instead of positive. This way the
later beacons get corrected to have a lower (and similar) timestamp with
regard to the beacon from slot 0.
I am not aware about any issues that have been caused by this.
Signed-off-by: Benjamin Berg <benjamin.berg@open-mesh.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes, this simply makes the code easier to understand
because all initialization based on ath9k_platform_data is now within
one function.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath9k_hw_init_macaddr unconditionally returns 0 in all cases, making the
return value unnecessary.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently setting the MAC address via ath9k_platform_data works only due
to the order in which init.c sets common->macaddr, which is done after
ath9k_hw_init_macaddr was executed. It would be better if the latter
was independent of the order in which it's being called.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
No functional changes - this only removes a variable which is set but
never read.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Some devices running OpenWrt need this and it makes sense to add this
to ath9k_platform_data as the next patches will add a devicetree
(boolean) property for it as well.
Suggested-by: Vittorio Gambaletta <openwrt@vittgam.net>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Fix up the wcn36xx_smd_update_scan_params() to work with non-ancient
versions of the firmware and support actually specifying the list of
channels.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The CCU block in WCNSS is configured for appropriate routing of
interrupts from the DXE to the application cpu, this is not dependant on
the iris version (wcn3660 vs wcn3680), but rather if the SoC has a riva
or pronto built in.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Split the wcnss mmio space into explicit regions for ccu and dxe and
acquire these from the node referenced by the qcom,mmio phandle.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In preparation for handling incoming messages from IRQ context, change
the indication list lock to a spinlock
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Merge the two allocation instead of separately allocating room for the
indication payload.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This driver contains some complicated if ... else if ... else constructions.
These are replaced by switch statements to improve readability.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192DE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8821AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8723BE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8723AE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8188EE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192CU chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The driver for RTL8192CE chips is converted to use the common routine
for getting the hardware information.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
All of the rtlwifi family of drivers have a similar routine that acquires
the hardware info from efuse and initializes a number of variables in the
driver's private area. A common routine is created for all drivers to use.
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
As interrupt is read in interrupt handler as well as interrupt processing
thread, we observed a corner case issue for MSI in which interrupt gets
processed twice.
This patch moves interrupt reading code for MSI mode from
mwifiex_interrupt_status() to mwifiex_pcie_process_int() to avoid the
issue.
Signed-off-by: Shengzhen Li <szli@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The PCIe driver didn't mask the host interrupts before trying to tear
down. This causes lockups at reboot or rmmod when using MSI-X on 8997,
since the MSI handler gets confused and locks up the system.
Also tested on 8897, which does not support MSI-X (and wasn't
experiencing this same bug). No regressions seen there.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PCIe-USB8997 variant is being used in the product. Let's change default
firmware from PCIe-UART to PCIe-USB. So by default PCIe-USB firmware would
be downloaded if version register doesn't give any information.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The two members min_scan_time and max_scan_time of structure
"mwifiex_ie_types_btcoex_scan_time" are of two bytes each. The values
are assigned directtly from firmware without endian conversion handling.
So, wrong datas will get saved in big-endian systems.
This patch converts the values into cpu's byte order before assigning them
into the local members.
Signed-off-by: Prasun Maiti <prasunmaiti87@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New firmwares (e.g. 10.10.69.36 for BCM4366) support "interface_remove"
for removing interfaces. Try to use this method on cfg80211 request. In
case of older firmwares (e.g. 7.35.177.56 for BCM43602 as I tested) this
will just result in firmware rejecting command and this won't change any
behavior.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far when receiving event about in-firmware-interface removal our
event worker was notifying listener and afterwards it was removing Linux
interface.
First of all it was resulting in slightly unexpected order. The listener
(del_virtual_intf callback) was (usually) returning with success before
we even called unregister_netdev(ice).
Please note this couldn't be simply fixed by changing order of calls in
brcmf_fweh_handle_if_event as unregistering interface earlier could free
struct brcmf_if.
Another problem of current implementation are possible lockups. Focus on
the time slot between calling event handler and removing Linux
interface. During that time original caller may leave (unlocking rtnl
semaphore) *and* another call to the same code may be done (locking it
again). If that happens our event handler will stuck at removing Linux
interface, it won't handle another event and will block process holding
rtnl lock.
This can be simply solved by unregistering interface in a proper
callback, right after receiving confirmation event from firmware. This
only required modifying worker to don't unregister on its own if there
is someone waiting for the event.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
scan_block flag is used to block scan operation when 4 way handshake
is in progress. Sometimes it doesn't get cleared due to incomplete
association. An example is assoc request/response is done, but add key
operation get canceled in some corner cases. As a result, further
association/scan operations are blocked.
This patch fixes the problem by clearing scan_block flag.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fix spelling typos found in drivers/net/wireless/realtek.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This allows the user to specify DMA aggregation timout and block
count. Blocks are presumably always 512 bytes, so the minimum block
count is 6 for 802.11 packets.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
gen2 chips as well as 8188eu seems to use this register for setting
DMA timeout threshold values, however the 8192cu is using
REG_USB_DMA_AGG_TO. Set both to be on the safe side.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Let the default to off until we have more data on the right default
tuning values.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This enables aggregation on rtl8192cu and derivative parts. This uses
the same parameters as for rtl8723au.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement rtl8xxxu_gen1_init_aggregation(). Aggregation should be the
same for all gen1 parts. We may want to allow for tuning parameters in
the fileopes struct. For now this is based allocating 16KB RX buffers,
leaving 16000 bytes for actual packets, and the rest for the skb
overhead.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The old allocation didn't leave space for phystats in the buffer,
allowing the packet to be rejected if a frame size of size
IEEE80211_MAX_FRAME_LEN was received.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This adds support for allocating larger skbs for devices which
indicate they support it.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements support for demuxing aggregated RX packets on gen1
devices, using the rxdesc16 format.
So far this has only been tested with rtl8723au devices.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This corrects the definition of rxdesc16 to correctly specify pkt_cnt
for aggregated packets. This is based on the code of the vendor
rtl8723au driver, as opposed to the struct definitions they use.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When handling aggregated packets, we'll get a new ieee80211_rx_status
for each cloned skb, so passing in the pointer from the outside
doesn't make sense.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is another prepatory patch to be able to handle aggregated RX
packets.
In order to avoid adding a prototype, this also moves the
rtl8723bu_handle_c2h() function.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This needs to be handled locally in the parse_rx_desc() function in
order to be able to handle aggregated packets in the future.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Changed the configuration to support 64bit instead of 32bit
this in order to offload the driver from handling a wraparound.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The flag should be cleaned along with other scan operation variables.
This was missing at some places.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will derive sta_priv at the beginning of suspend handler.
This will be useful for next patch in this series.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
RT_TRACE does not add a newline to the end of a message and always
emits at KERN_DEBUG so these are susceptible to message interleaving
from other processes without the newline.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This debugging macro can expand to a lot of code.
Make it a function to reduce code size.
(x86-64 defconfig w/ all rtlwifi drivers and allyesconfig)
$ size drivers/net/wireless/realtek/rtlwifi/built-in.o*
text data bss dec hex filename
900083 200499 1907 1102489 10d299 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.new
1113597 200499 1907 1316003 1414a3 drivers/net/wireless/realtek/rtlwifi/built-in.o.defconfig.old
1746879 453503 8512 2208894 21b47e drivers/net/wireless/realtek/rtlwifi/built-in.o.new
2051965 503311 8512 2563788 271ecc drivers/net/wireless/realtek/rtlwifi/built-in.o.old
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
USB urbs will return with a status != 0 when rmmod'ing the driver. No
need to fill the log with messages from rtl8xxxu_int_complete()
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
reg_eac and reg_ecc are only used if candidate is bigger than 0, and in
that case new values will be given to them. Removing the unused
assignments.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=PpSg
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-07-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* work on DQA continued
* SAR BIOS implementation
* some work on debugging capabilities
* added support for GCMP encryption
* data path rework in preparation for new HW
* some cleanup to remove transport dependency on mac80211
* support for MSIx in preparation for new HW
* lots of work in preparation for HW support (9000 and a000 series)
* general cleanups
* general bugfixes
Print an ath10k error message rather a call trace when HTT op version is
not found from firmware META data (IE). This should be sufficient to figure
out what went wrong.
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
QCA9888 shares the same configuration with QCA99X0
with NSS=2.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
rtc_state_cold_reset_mask is unused in ath10k_hw_regs.
instead fixed delays are used.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If WMI and/or firmware has issues removing the peer object,
then we still need to clean up the peer object in the driver.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Not sure this can happen, but seems like a reasonable sanity
check.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
just to comply to coding style.
Signed-off-by: Eduardo Abinader <eduardo.abinader@riverbed.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It is expected that all pktlog events for 10.4 firmware based solutions
should come through CE8 where as in case of 10.2 firmware based solutions,
it should come through one of the HTT events (HTT_T2H_MSG_TYPE_PKTLOG).
But from experiments with 10.4 based solutions, it is observed that pktlog
event for ATH_PKTLOG_TYPE_TX_MSDU_ID is coming through HTT pktlog event.
Currently, we always parse with 10.2 pktlog header which will lead to
pktlog decoding issues (payload length mismatch exceptions)
For trace points, it is required to provide only the payload size. So
fixing this by simplifying the payload size calculation without the use of
ath10k pktlog headers.
While there, remove the unused ath10k pktlog headers.
Signed-off-by: Ashok Raj Nagarajan <arnagara@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
<linux/semaphore.h> is not used anymore, so just remove the include.
Signed-off-by: Chaehyun Lim <chaehyun.lim@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
While debugging OS crashes due to firmware crashes, I enabled
kasan, and it noticed that peer objects were being used-after-freed.
Looks like there are two places we could be leaving stale references
in the peer-map, so clean that up.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Otherwise, the txrx-compl-task may access some bad memory?
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
cfg80211/nl80211 interface changes for per STA total rx-duration and
very basic 'ath10k_sta_statistics' mac80211 callback is implemented
to extend support for per station statistics from the driver.
Also provision in 'iw dev wlan#N station dump' to parse rx-duration
is supported. So its safer to remove the debugfs entry for per STA
rx-duration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Enable support for 'drv_sta_statistics' callback.
Export rx_duration support if available to cfg80211/nl80211
This can also act as a placeholder for any new per STA stats support
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
10.4 'extended peer stats' will be not be appended with normal peer stats
data and they shall be coming in separate chunks. Fix this by maintaining
a separate linked list 'extender peer stats' for 10.4 and update
rx_duration for per station statistics. Also parse through beacon filter
(if enabled), to make sure we parse the extended peer stats properly.
This issue was exposed when more than one client is connected and
extended peer stats for 10.4 is enabled
The order for the stats is as below
S - standard peer stats, E- extended peer stats, B - beacon filter stats
{S1, S2, S3..} -> {B1, B2, B3..}(if available) -> {E1, E2, E3..}
Fixes: f9575793d4 ("ath10k: enable parsing per station rx duration for 10.4")
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Add the following to support beacon report radio measurement
with the measurement mode field set to passive or active:
1. Propagate the required scan duration to the device
2. Report the scan start time (in terms of TSF)
3. Report each BSS's detection time (also in terms of TSF)
TSF times refer to the BSS that the interface that requested the
scan is connected to.
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
[changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match
the new API]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Beacon report radio measurement requires reporting observed BSSs
on the channels specified in the beacon request. If the measurement
mode is set to passive or active, it requires actually performing a
scan (passive or active, accordingly), and reporting the time that
the scan was started and the time each beacon/probe was received
(both in terms of TSF of the BSS of the requesting AP). If the
request mode is table, this information is optional.
In addition, the radio measurement request specifies the channel
dwell time for the measurement.
In order to use scan for beacon report when the mode is active or
passive, add a parameter to scan request that specifies the
channel dwell time, and add scan start time and beacon received time
to scan results information.
Supporting beacon report is required for Multi Band Operation (MBO).
Signed-off-by: Assaf Krauss <assaf.krauss@intel.com>
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add radar_detect_widths to the interface combination that allows
concurrent P2P Device dedicated interface and AP interfaces, to enable
testing of radar detection when P2P Device interface is used.
Clear the radar_detect_widths in case of multi channel contexts
as this is not currently supported.
As radar_detect_widths are now supported in all combinations,
remove the hwsim_if_dfs_limits definition since it is no longer
needed.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All transports has this structure. By moving it to be
shared, we can get rid of casting to the specific transport
in probe and remove.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Centralize the logging of SCD status. The motivation is
that for a000 devices we will have new SCD HW, but this
code was duplicate anyway, so it is a proper cleanup.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support for the v4 version of the TX power command. Just add a
new version and do the same sizing tricks that were done when support
for v3 was introduced.
This patch doesn't support the new functionality introduced, but makes
the driver work with the new size of the command.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
