Add an entry for the optional 'phy-clkgate-delay-us' property that is
used to describe the delay time between putting PHY into low power
mode and turning off the PHY clock.
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
On recent Qualcomm platforms VBUS and ID lines are not routed to
USB PHY LINK controller. Use extcon framework to receive connect
and disconnect ID and VBUS notification.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
rcar-du support for r8a7793/4
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm: rcar-du: Add support for the R8A7794 DU
drm: rcar-du: Add support for the R8A7793 DU
This pull request introduces the vc4 driver, for kernel modesetting on
the Raspberry Pi (bcm2835/bcm2836 architectures). It currently
supports a display plane and cursor on the HDMI output. The driver
doesn't do 3D, power management, or overlay planes yet.
[airlied: fixup the enable/disable vblank APIs]
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
* tag 'drm-vc4-next-2015-10-21' of http://github.com/anholt/linux:
drm/vc4: Allow vblank to be disabled
drm/vc4: Use the fbdev_cma helpers
drm/vc4: Add KMS support for Raspberry Pi.
drm/vc4: Add devicetree bindings for VC4.
* clk-iproc:
clk: iproc: define Broadcom NS2 iProc clock binding
clk: iproc: define Broadcom NSP iProc clock binding
clk: ns2: add clock support for Broadcom Northstar 2 SoC
clk: iproc: Separate status and control variables
clk: iproc: Split off dig_filter
clk: iproc: Add PLL base write function
clk: nsp: add clock support for Broadcom Northstar Plus SoC
clk: iproc: Add PWRCTRL support
clk: cygnus: Convert all macros to all caps
ARM: cygnus: fix link failures when CONFIG_COMMON_CLK_IPROC is disabled
Document the device tree bindings for Broadcom Northstar 2 architecture
based clock controller
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Document the device tree bindings for Broadcom Northstar Plus
architecture based clock controller
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The device tree should describe the chips (or chip-like subblocks) in
the system, but it generally does not describe individual registers --
it should identify, rather than describe, a programming interface.
This has not been the case with the QorIQ clockgen nodes. The
knowledge of what each bit setting of CLKCnCSR means is encoded in
three places (binding, pll node, and mux node), and the last also needs
to know which options are valid on a particular chip. All three of
these locations are considered stable ABI, making it difficult to fix
mistakes (of which I have found several), much less refactor the
abstraction to be able to address problems, limitations, or new chips.
Under the current binding, a pll clock specifier of 2 means that the
PLL is divided by 4 -- and the driver implements this, unless there
happen to be four clock-output-names rather than 3, in which case it
interprets it as PLL divided by 3. This does not appear in the binding
documentation at all. That hack is now considered stable ABI.
The current device tree nodes contain errors, such as saying that
T1040 can set a core clock to PLL/4 when only PLL and PLL/2 are options.
The current binding also ignores some restrictions on clock selection,
such as p5020's requirement that if a core uses the "wrong" PLL, that
PLL must be clocked lower than the "correct" PLL and be at most 80% of
the rated CPU frequency.
Possibly because of the lack of the ability to express such nuance in
the binding, some valid options are omitted from the device trees, such
as the ability on p4080 to run cores 0-3 from PLL3 and cores 4-7 from
PLL1 (again, only if they are at most 80% of rated CPU frequency).
This omission, combined with excessive caution in the cpufreq driver
(addressed in a subsequent patch), means that currently on a 1500 MHz
p4080 with typical PLL configuration, cpufreq can lower the frequency
to 1200 MHz on half the CPUs and do nothing on the others. With this
patchset, all CPUs can be lowered to 1200 MHz on a rev2 p4080, and on a
rev3 p4080 half can be lowered to 750 MHz and the other half to 600
MHz.
The current binding only deals with CPU clocks. To describe FMan in
the device tree, we need to describe its clock. Some chips have
additional muxes that work like the CPU muxes, but are not described in
the device tree. Others require inspecting the Reset Control Word to
determine which PLL is used. Rather than continue to extend this mess,
replace it. Have the driver bind to the chip-specific clockgen
compatible, and keep the detailed description of quirky chip variations
in the driver, where it can be easily fixed, refactored, and extended.
Older device trees will continue to work (including a workaround for
old ls1021a device trees that are missing compatible and reg in the
clockgen node, which even the old binding required). The pll/mux
details in old device trees will be ignored, but "clocks" properties
pointing at the old nodes will still work, and be directed at the
corresponding new clock.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
The R8A7794 DU has a fixed output routing configuration with one RGB
output per CRTC and thus lacks the RGB output routing register field.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
The R8A7793 DU is identical to the R8A7791 and thus only requires a new
DT compatible string.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
On some boards the energy enable detect mode leads in
trouble with some switches, so make the enabling of
this mode configurable through DT.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Neither the rockchip i2s nor the rockchip spdif binding support child
devices so #address-cells and #size-cells properties aren't required.
Remove these from the bindings.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
VC4 is the GPU (display and 3D) subsystem present on the 2835 and some
other Broadcom SoCs.
This binding follows the model of msm, imx, sti, and others, where
there is a subsystem node for the whole GPU, with nodes for the
individual HW components within it.
v2: Extend the commit message, fix several nits from Stephen Warren.
v3: Rename the compatibility strings, clean up node names, drop the
unnecessary lists of components. Use compatibility strings for
choosing CRTC HVS channel numbers. Document the HDMI clock usage.
v4: Whitespace fix, expand acronyms, move to display/ instead of gpu/,
rename "hpd-gpio" to "hpd-gpios".
Signed-off-by: Eric Anholt <eric@anholt.net>
On Renesas ARM SoCs (SH/R-Mobile, R-Car, RZ), the CPG (Clock Pulse
Generator) and MSSR (Module Standby and Software Reset) blocks are
intimately connected, and share the same register block.
Hence it makes sense to describe these two blocks using a
single device node in DT, instead of using a hierarchical structure with
multiple nodes, using a mix of generic and SoC-specific bindings.
These new DT bindings are intended to replace the existing DT bindings
for CPG core clocks ("renesas,*-cpg-clocks", "renesas,cpg-div6-clock")
and module clocks ("renesas,*-mstp-clocks"), at least for new SoCs.
This will make it easier to add module reset support later, which is
currently not implemented, and difficult to achieve using the existing
bindings due to the intertwined register layout.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Michael Turquette <mturquette@baylibre.com>
Reviewed-by: Magnus Damm <damm+renesas@opensource.se>
Enable the I2C core for this SoC. It is compitable to Gen2 SoCs, so
reuse the settings.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Enable the I2C core for this SoC. I add a new type because this version
has new features (e.g. DMA) which will be added somewhen later.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
According to "KeyStone Architecture Inter-IC Control Bus User Guide", fixed
additive part of frequency divisors (referred as "d" in the code and datasheet)
always equals to 6, independent of module clock prescaler.
module clock frequency
master clock frequency = ----------------------
(ICCL + 6) + (ICCH + 6)
It was not the case with original Davinci IP. Introduce new compatible property
"ti,keystone-i2c", which triggers special handling in the driver.
Without this change Keystone-based systems (having 204.8MHz input clock) choose
prescaler 29 (PSC=28). Using d=5 in this case leads to bus bitrate ~353kHz
instead of requested 400kHz. After correction, assuming d=6 bus rate is ~392kHz.
This gives ~11% transfer rate increase.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Hemanth Guruva Reddy <hemanth.guruva_reddy@nokia.com>
Tested-by: Lukasz Gemborowski <lukasz.gemborowski@nokia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Document the bindings used by exynos-rng Pseudo Random Number Generator
driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the vendor prefix for Boundary Devices Inc. which is a
supplier of ARM-based single board computers and System-on-Modules for
the general embedded market.
Website: http://boundarydevices.com/
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This change adds functionality to operate on reserved SRAM partitions
described in device tree file. Two partition properties are added,
"pool" and "export", the first one allows to share a specific partition
for usage by a kernel consumer in the same manner as it is done for
the whole SRAM device, and "export" property provides access to some
SRAM area from userspace over sysfs interface. Practically it is
possible to specify both properties for an SRAM partition, however
simultaneous access from a kernel consumer and from userspace is not
serialized, but still the combination may be useful for debugging
purpose.
The change opens the following scenarios of SRAM usage:
* updates in a particular SRAM area specified by offset and size are
done by bootloader, then this information is utilized by the kernel,
* a particular SRAM area is rw accessed from userspace, the stored
data is persistent on soft reboots,
* a device driver secures SRAM area for its purposes,
* etc.
Note, strictly speaking the added optional properties describe policy
of SRAM usage, rather than hardware, but here the policy mostly
resembles flash partitions in devicetree, which is undoubtedly
a very popular option but it does not describe hardware.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R8 is a new Allwinner SoC based on the A13. While both are very
similar, there's still a few differences. Introduce a new compatible to
deal with them.
In order to have a consistent naming, instead of mentioning the Allwinner
A series as the machine name, switch to sun4i/sun5i like what is done for
the other families.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
DS26522 is used for tdm, configured by SPI bus.
Add nodes under spi node to t104xd4rdb.dtsi.
Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
FT5506 is essentially the same as other FT5x06 devices other than
supporting 10 support points.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some encoders have both outputs low in stable states, others also have
a stable state with both outputs high (half-period mode) and some have
a stable state in all steps (quarter-period mode). The driver used to
support the former states and with this change it can also support the
later.
This commit also deprecates the 'half-period' property and introduces
a new property 'steps-per-period'. This property specifies the
number of steps (stable states) produced by the rotary encoder
for each GPIO period.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The anatop regulators are SoC internal LDO regulators usually supplied
by an external PMIC. This patch adds support for specifying the supply
from the device tree using the vin-supply property.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add berlin4ct to existing berlin pinctrl device tree binding.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently msi-parent is used by a few bindings to describe the
relationship between a PCI root complex and a single MSI controller, but
this property does not have a generic binding document.
Additionally, msi-parent is insufficient to describe more complex
relationships between MSI controllers and devices under a root complex,
where devices may be able to target multiple MSI controllers, or where
MSI controllers use (non-probeable) sideband information to distinguish
devices.
This patch adds a generic binding for mapping PCI devices to MSI
controllers. This document covers msi-parent, and a new msi-map property
(specific to PCI*) which may be used to map devices (identified by their
Requester ID) to sideband data for each MSI controller that they may
target.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
the bindings documentation to reflect this from Vladimir Zapolskiy.
"The change adds support of ARM PrimeCell PL175 MPMC and PL176 MPMC,
the static memory controllers on devices are similar to one found on
ARM PrimeCell PL172, add support to the existing driver."
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJWFtaVAAoJEF5zSH4+/j/ajj4H/1Yi5EZXpfSnSrLzETEkJbXF
VH0RLMA2ODgAgZEJt1y2mS0OW2ImDz2UIUDK86BbPP6cvyTxJft56nAMm8JHRrNU
M6PkOVIgkcSflqIW3LwJlW/TsXYvuaZQ+JJREZeeZT82IxQYAWyfnrKEyypfRTp2
1HTwTJv3E0RR0oefRF4kXnfHuRUlRcFbRjm4NyjH/mIj4HGIK+Vwjirkjq9U6xYn
7dGYj89soxVtlaSH/TTG9F4LnmGk/vOsvXlLBxgvYUWfOHvQDxgxPErVrj7GE2vv
tZ0iLs2tv4dbVo6D/YdQfLP576fKoVbjN3iKvlhP22w67b/QxVPXSgFxier5HK0=
=/iBk
-----END PGP SIGNATURE-----
Merge tag 'drivers_pl172_for_4.4' of https://github.com/manabian/linux-lpc into next/drivers
Merge "PL172 driver updates for v4.4" from Joachim Eastwood:
Support for additional ARM MPMCs to the PL172 driver and an update to
the bindings documentation to reflect this from Vladimir Zapolskiy.
"The change adds support of ARM PrimeCell PL175 MPMC and PL176 MPMC,
the static memory controllers on devices are similar to one found on
ARM PrimeCell PL172, add support to the existing driver."
* tag 'drivers_pl172_for_4.4' of https://github.com/manabian/linux-lpc:
doc: dt: arm,pl172: add description of PL175 and PL176 controllers
memory: pl172: add ARM PrimeCell PL176 MPMC support
memory: pl172: add ARM PrimeCell PL175 MPMC support
memory: pl172: correct MPMC peripheral ID register bits
Documentation and support to be able to load the PDSP
firmware necessary for accumulator operation.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T5UX
-----END PGP SIGNATURE-----
Merge tag 'keystone-driver-soc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/soc
Merge "ARM Keystone SOC driver updates for 4.4" from Santosh Shilimkar:
Documentation and support to be able to load the PDSP
firmware necessary for accumulator operation.
* tag 'keystone-driver-soc_v2' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: qmss: make acc queue support optional in the driver
soc: ti: add firmware file name as part of the driver
Documentation: dt: soc: Add description for knav qmss driver
L2 caches optimization for Armada XP
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlYX5kYACgkQCwYYjhRyO9XRAACgh9ZuCj/Bxgsql5tHL2fLPhMw
OzwAn3RJqjzRRMLcZ/TmgTPNbNwz3hEB
=bO2O
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-4.4-1' of git://git.infradead.org/linux-mvebu into next/soc
Merge "mvebu soc for 4.4 (part 1)" from Gregory CLEMENT:
L2 caches optimization for Armada XP
* tag 'mvebu-soc-4.4-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: add support to clear shared L2 bit on Armada XP
Despite being a platform device, the SMMUv3 is capable of signaling
interrupts using MSIs. Hook it into the platform MSI framework and
enjoy faults being reported in a new and exciting way.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
[will: tidied up the binding example and reworked most of the code]
Signed-off-by: Will Deacon <will.deacon@arm.com>
This changAdd support for EV_ABS / EV_REL events to the gpio-keys-polled driver.
The driver already allows specifying what type of events (key / rel / abs)
a button generates when pressed, but for rel / abs axis we also need to
specify which value this specific gpio represents.
One use case is digital joysticks / direction-pads which are hooked up to
gpio, in this case we've left and right buttons which we want to map to
EV_ABS, ABS_X and we want generate events for left with a value of -1 and
for right with a value of +1 (and similar for up / down and ABS_Y).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FqOp
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v4.4" from Kukjin Kim:
- New board support
: add exynos5250-snow-rev5 DT file to support Snow Rev5+ board
: add exynos5422-odroidxu4 DT file to support Odroid XU4 board
: split exynos5422-odroidxu3-audio DT file from odroidxu3-common
- USE GPIO constants for flags cells for exynos boards
- fix cpu compatible value to 'arm926ej-s' for s3c2416
- add DMA support for serial ports for exynos4
- add suspend opp for exynos4412
- remove regulator-compatible usage for exynos4412-trats2
- enable EC vboot context support for Peach boards
- move display-timings node to DP for exynos5250-arndale, smdk5250 and smdk5420
- for exynos4412-odroid/odroidu3
: unify voltage regulator style and
: remove redundant pinctrl settings
: add pwm-fan node and use it as a colling device
- for exynos5422-odroidxu3
: fix power off method and LEDs
- dt-bindings
: grounded AC0KB pin on S2MPS11
: entry how to use PWM FAN as a cooling device
* tag 'samsung-dt-1' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (22 commits)
ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
ARM: dts: Enable EC vboot context support on Peach boards
ARM: dts: Remove regulator-compatible usage in exynos4412-trats2
ARM: dts: Move display-timings node from fimd to dp in exynos5250-arndale, smdk5250 and smdk5420
ARM: dts: Add Exynos5250 Snow Rev5+ support on exynos5250-snow-rev5
ARM: dts: Unify voltage regulator style in exynos4412-odroid
ARM: dts: Remove redundant pinctrl settings in exynos4412-odroid
ARM: dts: Fix cpu compatible value for s3c2416
ARM: dts: Add support Odroid XU4 board for exynos5422-odroidxu4
ARM: dts: Split audio configuration to separate exynos5422-odroidxu3-audio
ARM: dts: Fix power off method for exynos5422-odroidxu3-common
dt-bindings: Document grounded ACOKB pin on S2MPS11
ARM: dts: use pwm-fan device as a cooling device for exynos4412-odroidu3
ARM: dts: Add pwm-fan node for exynos4412-odroidu3
dt-bindings: Documentation entry to explain how to use PWM FAN as a cooling device
ARM: dts: add suspend opp to exynos4412
...
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9u+p
-----END PGP SIGNATURE-----
Merge tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into next/drivers
Merge "ARM System Control and Power Interface(SCPI) support" from Sudeep Holla
It adds support for the following features provided by SCP firmware
using different subsystems in Linux:
1. SCPI mailbox protocol driver which using mailbox framework
2. Clocks provided by SCP using clock framework
3. CPU DVFS(cpufreq) using existing arm-big-little driver
4. SCPI based sensors including temperature sensors
* tag 'arm-scpi-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux:
hwmon: Support thermal zones registration for SCP temperature sensors
hwmon: Support sensors exported via ARM SCP interface
firmware: arm_scpi: Extend to support sensors
Documentation: add DT bindings for ARM SCPI sensors
cpufreq: arm_big_little: add SCPI interface driver
clk: scpi: add support for cpufreq virtual device
clk: add support for clocks provided by SCP(System Control Processor)
firmware: add support for ARM System Control and Power Interface(SCPI) protocol
Documentation: add DT binding for ARM System Control and Power Interface(SCPI) protocol
This adds documentation of device tree bindings for the STM32 hardware
random number generator.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The DSP processor sub-systems on DRA7xx have two MMU instances
each, one for the processor core and the other for an internal
EDMA block. These MMUs need an additional shared register to be
programmed in the DSP_SYSTEM sub-module to be enabled properly.
The OMAP IOMMU bindings is updated to account for this additional
syscon property required for these DSP IOMMU instances on DRA7xx
SoCs. A new compatible "ti,dra7-dsp-iommu" is also defined to
distinguish these devices specifically from other DRA7 IOMMU
devices.
An example of the DRA7 DSP IOMMU nodes is also added to the
document for clarity.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This patch adds wake up support to GPIO rotary encoders.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the Qualcomm Switch-Mode Battery Charger and Boost device tree
binding.
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
clock controller nodes which also support power domains (gdscs') need
to have a #power-domain-cells property. Add these for gcc and mmcc
nodes of msm8974, gcc of apq8084 and msm8916.
Also update gcc and mmcc bindings for it.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <agross@codeaurora.org>
Currently firmware file name is included in the DTS. This is not scalable
as user has to change the DTS if they need upgrade to a new firmware.
Instead, add the firmware file name in the driver itself. As long as there
is no API change, new firmware upgrade is easy and require no driver
change. User is expected to copy the firmware image to the file system
and add a sym link to the new firmware for doing an upgrade. Driver add
a array of firmware file names to search for the available firmware blobs.
This scheme also prepare the driver for future changes to API if ever
happens. In such case it is assumed that driver needs to change to
accommodate the new firmware and new firmware file name will get added to
the array.
Also update the DT document to remove the firmware attribute and add
description about firmware in the driver documentation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add documentation for the PXA LCD controller devicetree binding.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Reviewed-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Remove "mrvl,lpss-ssp" property from documentation because LPSS SSP type is
for certain Intel platforms. I believe commit a6e56c28a1
("ARM: pxa: ssp: add DT bindings") added it by accident by copying all
enum pxa_ssp_type types from include/linux/pxa2xx_ssp.h.
Please note this was removed from arch/arm/plat-pxa/ssp.c by the
commit b692cb83b1 ("ARM: pxa: ssp: Fix build error by removing originally
incorrect DT binding").
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Fix typos in the st,stih4xx binding, in particular replacing
"pinctrl-name" by "pinctrl-names".
Fix minor typos in the descriptions too.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Rob Herring <robh@kernel.org>
When referencing other DT bindings documentation, use relative
path rather than absolute.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
* clk-bcm2835:
clk: bcm2835: Add support for programming the audio domain clocks
clk: bcm2835: Add binding docs for the new platform clock driver.
clk: bcm2835: Move under bcm/ with other Broadcom SoC clk drivers.
We want the tty fixes and reverts in here as well so that people can
properly test and use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit add new cpu enable method "mediatek,mt65xx-smp" and
"mediatek,mt81xx-tz-smp".
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add clocks needed by Mediatek VENC and VENC_LT power domianis.
These clocks were needed by accessing subsystem's registers,
so they need to be enabled before power on these subsystems.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add compatible string for mt8127, mt8135 and mt8173 and sort
the list.
Signed-off-by: Yingjoe Chen <yingjoe.chen@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-10-08
Here's another set of Bluetooth & 802.15.4 patches for the 4.4 kernel.
802.15.4:
- Many improvements & fixes to the mrf24j40 driver
- Fixes and cleanups to nl802154, mac802154 & ieee802154 code
Bluetooth:
- New chipset support in btmrvl driver
- Fixes & cleanups to btbcm, btmrvl, bpa10x & btintel drivers
- Support for vendor specific diagnostic data through common API
- Cleanups to the 6lowpan code
- New events & message types for monitor channel
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these have
been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlYZOFUACgkQMUfUDdst+ymLSACeLNl7IWSxq2acJ5rhUl5+LRxp
KtsAn3lMXJryk4xw2WpfJg30TXpWXnNM
=n9ei
-----END PGP SIGNATURE-----
Merge tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB and PHY fixes and quirk updates for 4.3-rc5.
Nothing major here, full details in the shortlog, and all of these
have been in linux-next for a while"
* tag 'usb-4.3-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: Add device quirk for Logitech PTZ cameras
USB: chaoskey read offset bug
USB: Add reset-resume quirk for two Plantronics usb headphones.
usb: renesas_usbhs: Add support for R-Car H3
usb: renesas_usbhs: fix build warning if 64-bit architecture
usb: gadget: bdc: fix memory leak
phy: berlin-sata: Fix module autoload for OF platform driver
phy: rockchip-usb: power down phy when rockchip phy probe
phy: qcom-ufs: fix build error when the component is built as a module
Make the offset from the beginning of the "reg" property be from the
starting bus number, rather than zero. Hoist the invariant size
calculation out of the mapping for loop.
Update host-generic-pci.txt to clarify the semantics of the "reg" property
with respect to non-zero starting bus numbers.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Rob Herring <robh@kernel.org>
Add a quirk to clear the GUSB2PHYCFG.ENBLSLPM bit, which controls
whether the PHY receives the suspend signal from the controller.
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In 5388a6b266 ("ARM: SMP: Always enable clock event broadcast support")
Russell noted that "the TWD local timers are unable to wake up the CPU
when it is placed into a low power mode".
However, some platforms do not stop the TWD block in low-power mode,
and can thus use the TWD timer in one-shot mode, without setting up
a broadcast device.
Make the driver check for the "always-on" boolean property, and set
the CLOCK_EVT_FEAT_C3STOP flag accordingly.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge "Broadcom devicetree changes for v4.4" from Florian Fainelli:
This pull requests contains the following Broadcom SoCs Device Tree changes:
- Brian Norris documents the BCM7445 SoCs Power Management controllers and
hardware and updates the reference BCM7445 Device Tree with these nodes
- Florian Fainelli documents the BCM7xxx write-pairing feature in the top-level
BCM7xxx binding document
- Hauke Merthens enables the NAND controller for the Asus RT-AC87U and adds the
GPIO pin controlling the USB power supply on Netgear R6250
- Jon Mason adds support for the NorthStar Plus SoC by providing a top-level
binding document and the minimalist device tree skeleton for these SoCs
- Rafal Milecki adds support for the Netgear R7000 (BCM5301x SoC)
- Ray Jui provides a set of Cygnus DT changes that make the Device Tree clearer
and more correct with respect to how the hardware is designed. He also enables
the NAND controller on the bcm911360_entphn design, enables a bunch of
peripherals on the bcm958305k evaluation board, and adds a skeleton .dtsi file
for the touchscreen extansion board(s)
* tag 'arm-soc/for-4.4/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: move aliases back to .dts in Cygnus
ARM: dts: fix Cygnus nand device node
ARM: dts: enable touchscreen support on Cygnus
ARM: dts: Enable NAND support on bcm911360_entphn
ARM: dts: Enable various peripherals on bcm958305k
ARM: dts: Reorder Cygnus peripherals
ARM: dts: Move all Cygnus peripherals into axi bus
ARM: dts: Put Cygnus core components under core bus
ARM: dts: Use label for device nodes in Cygnus dts
ARM: dts: consolidate aliases for Cygnus dt files
ARM: BCM5301X: Netgear R6250 add USB GPIO
Documentation: bindings: brcmstb: Document write-pairing
ARM: dts: brcmstb: add BCM7445 system PM DT nodes
Documentation: dt: brcmstb: add system PM bindings
ARM: BCM5301X: add NAND flash chip description for Asus RT-AC87U
ARM: BCM5301X: Add DT for Netgear R7000
ARM: NSP: add minimal Northstar Plus device tree
dt-bindings: Create Documentation for NSP DT bindings
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWFta1AAoJEPOmecmc0R2BwsoH/iAhuYW/AMw9theS5e3QKYaT
AetDQHjjXPkbQpkMMxVpyyIGhBvHWHX+iTINqkVVx5MVlhvC1xmF4oJ6Yo4lbDVF
S6YgYrgI72P4inP0v3DZhJ2CpYB7bTVcPsU/ZiJOacvwKk2rgXWqE+nbBrZHpYbe
pDR9ONdOB0PsXfTsawcjb1FmK2/+xwRhHZJUSdlQRIoUZe1qIOjR2Lx25sprQ6vb
v6sBuY2T/rrWlKE0ME6HtdcA2s7HLKY1E1OdQPr15ceXR8k0yRz0dqH0ydULtZVZ
d6ZghxS+1ygir6Uw4sUXQa5QZjEeWU7M9+z6jCdKLEH/jUuaTFKFj+tko9uboa8=
=LB4D
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "Rockchip dts32 changes for 4.4" from Heiko Stuebner:
DTS changes including one new Veyron-board and the Radxa Rock2
system-on-module as well as the square baseboard. On top of that
a lot of mmc-related changes to improve speeds on the Cortex-A9
socs and also setting up the supplies for rk3288 mmc-controllers
for the following mmc-tuning support. And of course the dts-part
of the rk3288 power-domains.
* tag 'v4.4-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add the support power-domain node on RK3288 SoCs
ARM: dts: rockchip: add rk3288-firefly iodomains
ARM: dts: rockchip: fixup firefly mmc supplies
ARM: dts: rockchip: add rk3288-popmetal iodomains
ARM: dts: rockchip: add rk3288-popmetal mmc supplies
ARM: dts: rockchip: add rk3288-popmetal board to dtb list
ARM: dts: rockchip: Add dtb for the Radxa Rock 2 Square board
ARM: dts: rockchip: support highspeed sd-cards on rk3066a boards
ARM: dts: rockchip: support highspeed sd-cards for rk3188-radxarock
ARM: dts: rockchip: Add the hdmi-ddc pinctrl settings for rk3288
ARM: dts: rockchip: Remove specific cts pullup from veyron
ARM: dts: rockchip: pull up cts lines on rk3288
ARM: dts: rockchip: add veyron-jaq board
ARM: dts: rockchip: Add support for SD/MMC on MarsBoard-RK3066
dt-bindings: add power-domain header for RK3288 SoCs
support for the rk3288 powerdomain layout but can be easily
extended for the socs (including arm64) later on.
A big thanks to Ceasar Wang for pulling through on this
during 18 revisions.
Also included is a fix to the pm-clock handling in the generic
powerdomains to adapt it to the per-user clock handling we now
do, Acked by Rafael Wysocki.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJWFNeQAAoJEPOmecmc0R2BgHQH/RR/YS0IUPaeYhLr3FMVc47o
GrObw1uaNaykGSV8XYIxoxQaP+MwoW7Mw6ipfw+FLmqVGRjz8ljTIcnFrgz7hly1
CHmG6yCMjAeLh2ZMu3ge/VSQ7BdB7U690Coj5JnnfpO+Rufvu8Pp9sV+q4AH0qH2
bEfsoBoHQldTXCA5vlvH9C0CAqLDOBXWimgLRVi5TGCJjEsQINoeqJOWTl+hHnsi
arJs1sKBi71jFygsYXSZKIUnoZ1JUZofattPH8YgLeXNGUncEUYJsTTWYxm78ORt
3/iP0/mnqXnoFEqrY9Whi3IVpW60gnKUdUuAD4KK9vx1feT0bwLtVf/0lpCNXf8=
=txXq
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/drivers
Merge "Rockchip power-domain drivers for 4.4" from Heiko Stuebner:
Add the power-domain base-driver which currently contains
support for the rk3288 powerdomain layout but can be easily
extended for the socs (including arm64) later on.
A big thanks to Ceasar Wang for pulling through on this
during 18 revisions.
Also included is a fix to the pm-clock handling in the generic
powerdomains to adapt it to the per-user clock handling we now
do, Acked by Rafael Wysocki.
* tag 'v4.4-rockchip-drivers1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
soc: rockchip: power-domain: Add power domain driver
dt-bindings: add document of Rockchip power domains
PM / clk: Do not __clk_get passed in clock-references
dt-bindings: add power-domain header for RK3288 SoCs
The System Control Processor (SCP) provides access to SoC sensors via
the System Control and Power Interface (SCPI) Message Protocol. Add
bindings to allow probing of these sensors. Also support referencing
of the sensors for setting up thermal zones via the thermal DT
bindings.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Acked-by: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Add support for new PLL-type for stih418 A9-PLL.
Currently the 407_A9_PLL type being used, it is corrected with this patch
4600c28 PLL allows to reach higher frequencies
so its programming algorithm is extended.
Signed-off-by: Pankaj Dev <pankaj.dev@st.com>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the driver and devicetree documentation for the
Silicon Labs SI514 clock generator chip. This is an I2C controlled
oscillator capable of generating clock signals ranging from 100kHz
to 250MHz.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
[sboyd@codeaurora.org: Drop clk.h include, remove some casts]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add device tree binding documentation for the Qualcom Shared Memory
Manager.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Andy Gross <agross@codeaurora.org>
The Radxa Rock 2 Square board is a combination of the Radxa Rock 2 SoM
with the Square baseboard. Add a dtsi for the SoM which can be included
into the dts for the various baseboards (e.g. full and square) and a dts
for the square board.
Currently supported are serial console, wired networking, hdmi output,
eMMC and SD storage and USB.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
a.k.a. Haier Chromebook 11, and others
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tronfy is an emerging brand in China specializing in Home Theater
solutions for the normal consumers.
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ceDx
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v4.4" from Simon Horman:
* Add missing CPG/MSTP Clock Domain for sound on r8a779[01] SoCs
* Tidy up SCI resource region on r8a779[018] SoCs
* Add pinmux for iic0 on Lager board
* Use CCF for audio clock on Lager and Koelsch boards
* Use serial0 and 1 as serial ports on Marzen board
* Use adxl345-specific compatible property for KZM9G board
* Document compat string for Silk board
* Enable GPIO, I2C, PCI, QSPI, USB PHY and HS, and VIN support on r8a7794/Silk
* Add initial support for r8a7791/porter
* Add common file for AA121TD01 panel
* tag 'renesas-dt-for-v4.4' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (28 commits)
ARM: shmobile: porter: add Ether DT support
ARM: shmobile: fix SILK board name
ARM: shmobile: r8a7794: add HS-USB DT support
ARM: shmobile: dts: Add common file for AA121TD01 panel
ARM: shmobile: r8a7794: link PCI USB devices to USB PHY
ARM: shmobile: silk: enable USB PHY
ARM: shmobile: r8a7794: add USB PHY DT support
ARM: shmobile: porter: initial device tree
ARM: shmobile: add Porter board DT bindings
ARM: shmobile: silk: enable internal PCI
ARM: shmobile: r8a7794: add internal PCI bridge nodes
ARM: shmobile: r8a7790: lager: add pinmux for iic0
ARM: shmobile: r8a7778: tidyup SSI resource region
ARM: shmobile: r8a7791: tidyup SSI resource region
ARM: shmobile: r8a7790: tidyup SSI resource region
ARM: shmobile: lager: use CCF for audio clock
ARM: shmobile: koelsch: use CCF for audio clock
ARM: shmobile: silk: add VIN0/ADV7180 DT support
ARM: shmobile: r8a7794: add VIN DT support
ARM: shmobile: silk: add I2C1 DT support
...
Add devicetree bindings for the spdif tranceiver found on
found on rk3066, rk3188 and rk3288 SoCs
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT nodes should not append their addresses with '0x'.
Suggested-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Add device tree binding documentation for the Broadcom iProc MDIO
bus driver.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Description previously stated MHz whereas the resolution is in Hz.
This has now has been updated to align with reality.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Cortex-A57 PMU supports a few events outside of the required PMUv3
set that are rather useful.
This patch adds the event map data for said events.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The Cortex-A53 PMU supports a few events outside of the required PMUv3
set that are rather useful.
This patch adds the event map data for said events.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the "fsl,wake-on-filer" property for eTSEC nodes to
indicate that the system has the power management
infrastructure needed to be able to wake up the system
via FGPI (filer, aka. h/w rx parser) interrupt.
Cc: Li Yang <leoli@freescale.com>
Cc: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of the boards have their headphone jack directly connected to the
matching pins of the SoCs. Since most of the time we will have the same
routing path, it makes no sense to put that in the DTS, since it will only
be some useless duplication there.
It also fixes the following warning messages that were seen so far, on
boards where we were using the bindings in the documentation example.
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Left -> direct -> Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Right -> direct -> Headphone Jack
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This defines the spi1 and spi2 devices in the device-tree.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Keystone2 devices are used on more platforms than just Texas
Instruments reference evaluation platforms called EVMs. Providing a
generic compatible "ti,keystone" is not sufficient to differentiate
various SoC definitions possible on various platforms for the
following reasons:
a) Userspace applications have no way of knowing which SoC they are
functioning, providing the compatible matches provide a mechanism for
them to enable SoC specific functionality. Such userspace applications
are typically automated test framework or SoC custom hardware
acceleration entitlement from a common file system.
b) Provides an accurate hardware description. This allows
SoC specific logic to be run time handled based on
of_machine_is_compatible("ti,k2hk") or as needed for the dependent
processor instead of needing to use board dependent compatibles that
are needed now.
Hence, provide compatible matches for each SoC in the Keystone family.
Acked-By: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
add a DT binding documentation of usb3.0 phy for MT65xx
SoCs from Mediatek.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Exynos USB2 PHY has separate power supply, which is usually provided by
VBUS regulator. This patch adds support for it. VBUS regulator is
optional, to keep compatibility with boards, which have VBUS provided
from some always-on power source.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Document the device-tree binding of MediaTek display PWM. The PWM has
one channel to control the backlight brightness for display. Both the
MT8173 and MT6595 are supported.
Signed-off-by: YH Huang <yh.huang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This is needed due to the duplicated iommu stuff to help with the merge
and to prevent future issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The optional "regulators" is a node and not a property so it should not
be in the "Optional properties" section but in an "Optional nodes" one.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This add the necessary binding documentation for the power domains
found on Rockchip SoCs.
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add a binding documentation for the Broadcom BCM7038 PWM controller found in
BCM7xxx chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWEUxnAAoJEHm+PkMAQRiGYCYH/3gtGkFdvSLi+E1PfI8Qk3ZA
XuYA4Mj09JBVSmaICeueMTDVrdiq0OE0zPib26GWlF/za13kNU8KgMR3+6XCuLSX
DiCmh6mwDItoNoSIIUERLqrFHABXz8rZ3gb3uu2+kNN74Cl0piNm1YpFclEEWjMr
9Wk5fkq+ontnDVUQOvWUxPiUXOJTvdLXBWTRDw1yTdE3RMNwRI2d/hme6Hq++WYV
tRalZZKQaoB33js9WRVAoLVunvtna+i+/y7VGLj8QyS0+d6ec81Hey2r1/fR/oG4
bs4ul6vtqeb3IR/PjUqxF59pSrCLEO+qrp9KrTlJNYgr1m1QyjRxWUdy/XhyaWo=
=gIhN
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc4' into next
Merge with mainline to sync up with changes to parkbd driver.
The max77802 regulator driver defines the supply name for each regulator
so these can be described in DT but is not mentioned in the binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DC1SW and DC5LDO regulators in the AXP221 are internally chained
to DCDC1 and DCDC5, hence the names. The original bindings used the
parent regulator names for the supply regulator property. This causes
some confusion when we actually use it in the dts:
axp221 {
/* self supplying? */
dcdc1-supply = <&dcdc1>;
dcdc5-supply = <&dcdc5>;
dcdc1: dcdc1 {
...
};
dcdc5: dcdc5 {
...
};
};
Since they are internally connected within the PMIC, their relationships
should not be visible in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add DT binding documentation for the Berlin PWM controller.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patches makes following changes to omap_hdq driver
- Enable 1-wire mode.
- Implement w1_triplet callback to facilitate search rom
procedure and auto detection of 1-wire slaves.
- Proper enabling and disabling of interrupt.
- Cleanups (formatting and return value checks).
HDQ mode remains unchanged.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jonathan Corbet <corbet@lwn.net>
CC: Tony Lindgren <tony@atomide.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unfortunately, the SILK board bindings were not quite correct, as the board
name should be all caps. Fix that, adding the board model # in parens and
removing stray semicolon.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add receive DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add transmit DMA support for UARTDM type of controllers.
Tested on APQ8064, which have UARTDM v1.3 and ADM DMA engine
and APQ8016, which have UARTDM v1.4 and BAM DMA engine.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the DW_apb_uart is configured with UART_16550_COMPATIBLE
configuration parameter set, then the Busy Functionality is
not available. These UARTs will never generate the Busy
detect indication interrupt, and therefore don't need
handling for it.
This creates a small optimization for the DW_apb_uarts
configured without the busy functionality, but more
importantly, it removes the small but real risk of hitting
potential issues caused by busy functionality handling when
no busy functionality exist.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add these variants of the UART as compatible strings
Signed-off-by: Matt Redfearn <matt.redfearn@imgtec.com>
blah
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds the devicetree bindings for the Freescale MXS On Chip
OTP driver.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch updates the ravb binding to support the r8a7795 SoC by:
- Adding a compat string for the new hardware
- Adding 25 named interrupts to binding for the new SoC;
older SoCs continue to use a single multiplexed interrupt
The example is also updated to reflect the r8a7795 as this is the
more complex case.
Based on work by Kazuya Mizuguchi and others.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TCA9539 is almost identical to the PCA9555 and software-compatible
with this driver. It exposes 16 general purpose I/O pins in two 8-bit
configurations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Pull input layer fixes from Dmitry Torokhov:
"Fixes for two recent regressions (in Synaptics PS/2 and uinput
drivers) and some more driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - fix handling of disabling gesture mode"
Input: psmouse - fix data race in __ps2_command
Input: elan_i2c - add all valid ic type for i2c/smbus
Input: zhenhua - ensure we have BITREVERSE
Input: omap4-keypad - fix memory leak
Input: serio - fix blocking of parport
Input: uinput - fix crash when using ABS events
Input: elan_i2c - expand maximum product_id form 0xFF to 0xFFFF
Input: elan_i2c - add ic type 0x03
Input: elan_i2c - don't require known iap version
Input: imx6ul_tsc - fix controller name
Input: imx6ul_tsc - use the preferred method for kzalloc()
Input: imx6ul_tsc - check for negative return value
Input: imx6ul_tsc - propagate the errors
Input: walkera0701 - fix abs() calculations on 64 bit values
Input: mms114 - remove unneded semicolons
Input: pm8941-pwrkey - remove unneded semicolon
Input: fix typo in MT documentation
Input: cyapa - fix address of Gen3 devices in device tree documentation
Add iomuxc-lpsr devicetree bindings documentation
Provide documentation context as well an example on
pheriperals that could use pad from either iomuxc controller
supported by iMX7D SoC
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds support for the FT6x06 and the FT6x36 family of capacitive touch
panel controllers, in particular the FT6236.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull mediatek clock support and fixes from James Liao:
"This is a collection of new Mediatek clocks support and fixes.
These patches come from Joe and me, including clock support for
subsystems, GPT and some minor fixes."
* 'v4.3-rc3-clk' of https://github.com/jamesjjliao/linux:
clk: mediatek: Add USB clock support in MT8173 APMIXEDSYS
clk: mediatek: Add subsystem clocks of MT8173
dt-bindings: ARM: Mediatek: Document devicetree bindings for clock controllers
clk: mediatek: Fix rate and dependency of MT8173 clocks
clk: mediatek: Add fixed clocks support for Mediatek SoC.
clk: mediatek: Add __initdata and __init for data and functions
clk: mediatek: Remove unused code from MT8173.
clk: mediatek: Removed unused dpi_ck clock from MT8173
clk: mediatek: add 13mhz clock for MT8173
Add a DT property "active-semi,vsel-high" to indicate the VSEL pin
is high. If this property is missing, then assume the VSEL pin is
low(0).
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
PSCI 1.0 is designed to be fully compliant to the PSCI 0.2
specification, with minor differences that are described in the
PSCI specification.
In particular, PSCI v1.0 augments the specification with a new
power_state format (extended stateid - probeable through the
PSCI_FEATURES call), changes some function return codes and
functions usage requirements wrt PSCI 0.2. These changes mean
that 1.0 vs 0.2 compliancy should be enforced through a DT
compatible string that allows firmware to specify 1.0 only
compliancy so that older kernels are prevented from using
PSCI 1.0 FW implementations in a non-compatible way (eg by
calling a 1.0 FW implementation and expecting 0.2 behaviour).
This patch adds PSCI 1.0 DT bindings and related compatible
string.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Jisheng Zhang <jszhang@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
It is customary for GPIO controllers to support open drain/collector
and open source/emitter configurations. Add standard GPIO line flags
to account for this and augment the documentation to say that these
are the most generic bindings.
Several people approached me to add new flags to the lines, and this
makes sense, but let's first bind up the most common cases before we
start to add exotic stuff.
Thanks to H. Nikolaus Schaller for ideas on how to encode single-ended
wiring such as open drain/source and open collector/emitter.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove this driver now that Bjorn has introduced a pinctrl driver
for msm8660 and the dts files have been updated with the pinctrl
compatibles.
Cc: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner A83T soc port controller has 8 ports.
It has 3 IRQ banks namely PB, PG, PH.
Pinmuxing are different for some pins as compared to
sun8i A23 and A33.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
interrupts-names => interrupt-names
Other line changes are re-aligning.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add Porter device tree bindings documentation, listing it as a supported board.
This allows to use checkpatch to validate DTSes referring to the Porter board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Previously we've only supported a few fixed clocks based on
assumptions about how the firmware sets up the clocks, but this
binding will let us control the actual (audio power domain) clock
manager.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Lee Jones <lee@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new type of clocks that can be provided to a peripheral.
In addition to the peripheral clock, this new clock that can use several
input clocks as parents can generate divided rates.
This would allow a peripheral to have finer grained clocks for generating
a baud rate, clocking an asynchronous part or having more
options in frequency.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[sboyd@codeaurora.org: Transition to new clk_hw provider APIs]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
JPEG IP found in Exynos5433 is similar to what is in Exynos4, but
there are some subtle differences which this patch takes into account.
The most important difference is in what is processed by the JPEG IP and
what has to be provided to it. In case of 5433 the IP does not parse
Huffman and quantisation tables, so this has to be performed with the CPU
and the majority of the code in this patch does that.
A small but important difference is in what address is passed to the JPEG
IP. In case of 5433 it is the SOS (start of scan) position, which is
natural, because the headers must be parsed elsewhere.
There is also a difference in how the hardware is put to work in
device_run.
Data structures are extended as appropriate to accommodate the above
changes.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Reviewed-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This adds the binding documentation for the mmsys, imgsys, vdecsys,
vencsys and vencltsys controllers found on Mediatek SoCs.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=E+jf
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new driver, new functionality and cleanups for IIO in the 4.4 cycle
New device support
* APDS9960 ALS + proximity driver
* bmg160 SPI devices.
* HDC100x humidity sensors
* Holt HI-8435 threshold detector
* mma8453Q accelerometer added to the mma8452 driver
* mma86452FC and mma8653FC accelerometers added to the mma8452 driver
* mxc4005 accelerometer
* PulsedLight LIDAR
* SensorTech VZ89x volatile organic compound sensor
* UPISEMI uS5182d ALS and proximity sensors
New core functionality
* triggered events - use triggers to check for changes in threshold type
detectors on devices with out interrupt support. First user is the holt
comparator.
* chemical concentration and resistance channel types.
New driver functionality
* vf610
- buffer support.
- followup coccinelle warning fix.
Core rework
* buffers
- break out callback buffer to own module.
- move buffer implementations to a new subdirectory
* percolate the error code form iio_event_getfd out to userspace
rather than giving a missleading error later on.
Cleanups
* adddac drivers
- use BIT macro where appropriate.
* meter drivers
- use BIT macro where appropriate.
* ad7303
- add an OF match table to line up with the binding docs.
* adc128s052
- add an OF match table to line up with the binding docs.
* adf4350
- add an OF match table to line up with the binding docs
* as3935
- add an OF match table to line up with the binding docs.
* berlin2-adc
- use GENMASK and BIT for masks
- prevent attempting to sample multiple channels at once by moving a
mutex scop
- coding style cleanups
* bmg150_magn
- kconfig sort order was wrong - fix it.
* bmg160
- use i2c regmap and drop all uses of i2c_client
- separate i2c and core driver
* cc10001_adc
- kconfig sort order was wrong - fix it.
* evgen (dummy driver helper module)
- move interrupt generation to irq_work to reduce differences between
the dummy driver and real hardware drivers.
* hmc5843
- set the name dynamically rather than to a fixed value for one of the
suported parts.
- export module alias information to allow autoprobing of module.
* lpc32xx
- on failure to get resource or irq return -ENXIO as uppose to -EBUSY
* max1027
- set .of_match_table to actually allow OF style matching.
* max5821
- add MODULE_DEVICE_TABLE for OF table.
* mma8452
- refactor to separate out chip specific data.
- add freefall / motion interrupt source for devices that do their
interrupts slightly differently.
- update copywrite notice.
- leave naming of events directory in sysfs to the core
* mcp320x
- set .of_match_table so that it can be use for OF style matching.
* mlx90614
- Implement filter configuration (note the datasheet changed as a result
of the driver reviews to include the values we needed ;)
* opt3001
- drop .owner field as assigned by platform driver core.
* si7020
- replace a bitmask on the humidity values with a more correct range
check.
* stk310
- improved error handling.
- use BIT macro where appropriate and use the resulting defines
instead of magic numbers in the code.
- fix indentation
* st-sensors
- add debugfs register read hook
* tsl4531
- fix error handling in check_id
* twl6030
- fix module autoload for OF
* iio-trig-sysfs
- document add and remove attribute
* trigger in staging
- code alignment fixes.
- braces on both branches of if statement if needed for one.
* xilinx-xadc
- push interrupts into hardirq context as there isn't much in them
any more and it avoids breaking PREEMPT_RT builds due to the use
of a spinlock between the hardirq and the thread.
Tools
* event-monitor
- report unsupported events. We keep expanding what can come from drivers
so give a helpful error if one turns up in an out of date userspace
program.
* generic-buffer
- helpful message about needing to enable a channel to start the buffer.
Add DA9062 OnKey support into the existing DA9063 OnKey driver component by
using generic access tables for common register and bit mask definitions.
The following change will add generic register and bit mask support to the
DA9063 OnKey.
The following alterations have been made to the DA9063 OnKey:
- Addition of a da906x_chip_config structure to hold all
generic registers and bitmasks for this type of OnKey component.
- Addition of an struct of_device_id table for DA9063 and DA9062
defaults
- Refactoring functions to use struct da9063_onkey accesses to generic
registers/masks instead of using defines from registers.h
- Re-work of da9063_onkey_probe() to use of_match_node() and
dev_get_regmap() to provide initialisation of generic registers and
masks and access to regmap
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWB9f6AAoJEHm+PkMAQRiGiFMIAJYFLIkF/dXFYMNPGsRGRGYO
SsQkfYzjy4i/yloyVlGB33e6dqxWdVgCeqYC77TO+1CBq34o6dqM4PACTrhjtS+3
qQvaP/qn6cSoaGIkdD3v43CCiwMpZZ5+Uj7F7Uz8N4twrpykOZFMM5T7f1lrsG2F
wJGafmvok9NU2F2wYwaJ8JrzsF6iO6ibFeB8BosRF5Ba4nKqiXVI0xNa0R8PFDm3
tbh/IkkqokemEqnHyWyszhGFsCQupi+QgsjY/LhWUcCaL7HLEgJmkBX0tXNlgMmK
TFCq7L8Bigu4nlgZ/iVUB9kh4GTBNVcbdRVN3loJFlczFJlIAa171OVlfRu3lvU=
=m29x
-----END PGP SIGNATURE-----
Merge tag 'v4.3-rc3' into next
Merge with Linux 4.3-rc3 to bring in MFD DA9062 changes to merge DA9062
OnKey driver.
Add OMAP36xx support to ti-soc-thermal driver. This
chip is also unreliable. The data provided here is
based on OMAP36xx TRM:
http://www.ti.com/lit/ug/swpu177aa/swpu177aa.pdf
Signed-off-by: Eduardo Valentin <edubezva@gmail.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
This adds support for OMAP3 chips to ti-soc-thermal. As requested by
TI people, it is marked unreliable and warning is printed.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
For some reason the name of the external interrupt controller
has changed name with r8a7795, so use "intc-ex" instead of "irqc"
as r8a7795 compat string to follow the friendly documentation.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Reviewed-by: horms@verge.net.au
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: jason@lakedaemon.net
Cc: Magnus Damm <magnus.damm@gmail.com>
Link: http://lkml.kernel.org/r/20150928094228.32552.83336.sendpatchset@little-apple
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit fe78d0b769 ("spi: sh-msiof: Fix FIFO size to 64 word from
256 word") changed the default RX FIFO size on R-Car Gen2 SoCs in the
driver code, but forgot to update the DT bindings documentation.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Extend the bq24257 charger's device tree documentation to cover the
bq24250 and bq24251 devices as well feature additions.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
For optimal performance, in a HW I/O coherency context such as the one
used on Armada XP, the shared L2 bit of the CPU configuration register
should be cleared.
This commit adjusts the coherency fabric code used by Marvell EBU
processors to clear this bit on Armada XP. Since it's a per-CPU
register, it's cleared in set_cpu_coherent() for the boot CPU, and
through a CPU notifier for the non-boot CPUs.
[gregory.clement@free-electrons.com: rebasd on 4.3-rc1]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds devicetree binding for System Control and Power
Interface (SCPI) Message Protocol used between the Application Cores(AP)
and the System Control Processor(SCP). The MHU peripheral provides a
mechanism for inter-processor communication between SCP's M3 processor
and AP.
SCP offers control and management of the core/cluster power states,
various power domain DVFS including the core/cluster, certain system
clocks configuration, thermal sensors and many others.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
CC: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Jon Medhurst (Tixy) <tixy@linaro.org>
Cc: devicetree@vger.kernel.org
Instead of hardcoding IRQ trigger type to IRQF_TRIGGER_FALLING, let's
respect settings specified in device tree. To be compatible with older
DTSes, if trigger type is not set up in DTS we'll set it to default
(falling edge).
Tested-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current/old gpio framework used doesn't properly listen to
ACTIVE_LOW and ACTIVE_HIGH flags. The newer gpio framework takes into
account these flags when setting gpio values.
Since the values being output were based on voltage and not logic they
change to reflect this difference. Also use gpiod_set_value_cansleep since
wake and reset pins can be provided by bus based io expanders.
Switch from msleep(5) to udelay_range(5000,6000) to avoid check patch
warning.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MIPS fixes from Ralf Baechle:
- Properly setup irq handling for ATH79 platforms
- Fix bootmem mapstart calculation for contiguous maps
- Handle little endian and older CPUs correct in BPF
- Fix console for Fulong 2E systems
- Handle FTLB correctly on R6 CPUs
- Fixes for CM, GIC and MAAR support code
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Initialise MAARs on secondary CPUs
MIPS: print MAAR configuration during boot
MIPS: mm: compile maar_init unconditionally
irqchip: mips-gic: Fix pending & mask reads for MIPS64 with 32b GIC.
irqchip: mips-gic: Convert CPU numbers to VP IDs.
MIPS: CM: Provide a function to map from CPU to VP ID.
MIPS: Fix FTLB detection for R6
MIPS: cpu-features: Add cpu_has_ftlb
MIPS: ATH79: Add irq chip ar7240-misc-intc
MIPS: ATH79: Set missing irq ack handler for ar7100-misc-intc irq chip
MIPS: BPF: Fix build on pre-R2 little endian CPUs
MIPS: BPF: Avoid unreachable code on little endian
MIPS: bootmem: Fix mapstart calculation for contiguous maps
MIPS: Fix console output for Fulong2e system
Add snps,quirk-frame-length-adjustment property which provides value
for post silicon frame length adjustment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlYGzJ0ACgkQMUfUDdst+yneGACgxrj/ZJGgY09tkItvvejHoYrF
tgQAoI/cRL7C9aoWt7DjMxmbFnQE8hC7
=jsj/
-----END PGP SIGNATURE-----
Merge tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some USB driver fixes for 4.3-rc3.
There's the usual assortment of new device ids, combined with xhci and
gadget driver fixes. Full details in the shortlog. All of these have
been in linux-next with no reported problems"
* tag 'usb-4.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (34 commits)
MAINTAINERS: remove amd5536udc USB gadget driver maintainer
USB: whiteheat: fix potential null-deref at probe
xhci: init command timeout timer earlier to avoid deleting it uninitialized
xhci: change xhci 1.0 only restrictions to support xhci 1.1
usb: xhci: exit early in xhci_setup_device() if we're halted or dying
usb: xhci: stop everything on the first call to xhci_stop
usb: xhci: Clear XHCI_STATE_DYING on start
usb: xhci: lock mutex on xhci_stop
xhci: Move xhci_pme_quirk() behind #ifdef CONFIG_PM
xhci: give command abortion one more chance before killing xhci
usb: Use the USB_SS_MULT() macro to get the burst multiplier.
usb: dwc3: gadget: Fix BUG in RT config
usb: musb: fix cppi channel teardown for isoch transfer
usb: phy: isp1301: Export I2C module alias information
usb: gadget: drop null test before destroy functions
usb: gadget: dummy_hcd: in transfer(), return data sent, not limit
usb: gadget: dummy_hcd: fix rescan logic for transfer
usb: gadget: dummy_hcd: fix unneeded else-if condition
usb: gadget: dummy_hcd: emulate sending zlp in packet logic
usb: musb: dsps: fix polling in device-only mode
...
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the device tree bindings with added support for outbound mapping
configurations.
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Resource management
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn Helgaas)
MSI
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=f4c3
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for things we merged for v4.3 (VPD, MSI, and bridge
window management), and a new Renesas R8A7794 SoC device ID.
Details:
Resource management:
- Revert pci_read_bridge_bases() unification (Bjorn Helgaas)
- Clear IORESOURCE_UNSET when clipping a bridge window (Bjorn
Helgaas)
MSI:
- Fix MSI IRQ domains for VFs on virtual buses (Alex Williamson)
Renesas R-Car host bridge driver:
- Add R8A7794 support (Sergei Shtylyov)
Miscellaneous:
- Fix devfn for VPD access through function 0 (Alex Williamson)
- Use function 0 VPD only for identical functions (Alex Williamson)"
* tag 'pci-v4.3-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: rcar: Add R8A7794 support
PCI: Use function 0 VPD for identical functions, regular VPD for others
PCI: Fix devfn for VPD access through function 0
PCI/MSI: Fix MSI IRQ domains for VFs on virtual buses
PCI: Clear IORESOURCE_UNSET when clipping a bridge window
PCI: Revert "PCI: Call pci_read_bridge_bases() from core instead of arch code"
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBI2/AAoJEMhvYp4jgsXi08cH/11S/92w1PLNmWCv4y7TXHQw
XTJi7/Hk+q6otV/FigXukdYClR17h/3mFyCKKXHrkAgy/AoSrvN/ABe0bLLoT2AQ
xh0Rx8F6vZwa6ro1MZcrn3ZxQkoJlNUhoIXtY84oSPWd1ernLOar6HonFiynCQQc
bDZo5zoLj6DBbSO+UpVvEQN57ogwPgFZ1hGDjJeyyH8c1755z2OVA+k8O0dwjmqW
Xav/7TO8bFEIbUnfWeKnVyK45qmJxHcTbn3nxUgYFQj3DMI2Hn86WEY4cg8QvTo+
SpdO1Aio6b9NSTNnpiSvPnc2MFNPFaWjiqm1w86w+PTm8oUT+p1V0OG/EE27fcY=
=VUfk
-----END PGP SIGNATURE-----
Merge tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Silence bogus warning for of_irq_parse_pci
- Fix typo in ARM idle-states binding doc and dts files
- Various minor binding documentation updates
* tag 'devicetree-fixes-for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
Documentation: arm: Fix typo in the idle-states bindings examples
gpio: mention in DT binding doc that <name>-gpio is deprecated
of_pci_irq: Silence bogus "of_irq_parse_pci() failed ..." messages.
devicetree: bindings: Extend the bma180 bindings with bma250 info
of: thermal: Mark cooling-*-level properties optional
of: thermal: Fix inconsitency between cooling-*-state and cooling-*-level
Docs: dt: add #msi-cells to GICv3 ITS binding
of: add vendor prefix for Socionext Inc.
The idle-states bindings mandate that the entry-method string
in the idle-states node must be "psci" for ARM v8 64-bit systems,
but the examples in the bindings report a wrong entry-method string.
Owing to this typo, some dts in the kernel wrongly defined the
entry-method property, since they likely cut and pasted the example
definition without paying attention to the bindings definitions.
This patch fixes the typo in the DT idle states bindings examples and
respective dts in the kernel so that the bindings and related dts
files are made compliant.
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Howard Chen <howard.chen@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Rob Herring <robh@kernel.org>
The gpiolib supports parsing DT properties of the form <name>-gpio but it
was only added for compatibility with older DT bindings that got it wrong
and should not be used in newer bindings.
The commit that added support for this was:
dd34c37aa3 ("gpio: of: Allow -gpio suffix for property names")
but didn't update the documentation to explain this so it's been a source
of confusion. So let's make this clear in the GPIO DT binding doc.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add Renesas R8A7794 SoC support to the Renesas R-Car gen2 PCI driver.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bjorn Helgaas <helgaas@kernel.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
The TPS65217 charger is a subnode of the TPS65217 MFD.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling. The
driver fixes are all of the usual important if you see them variety.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWBDUFAAoJECTWi3JdVIfQir4H/RIAsfP5QqSzjQHmeZk1eHJv
FIzUiHARK5Jy3ORXVCh3dh8JB67NF9Qa4p/fDcHhk0DFju+HTyvUHmChzGPwEw86
0lRv2PKhHu9e7vJG8IZXKbZKeBT9RtrVe8yQ7SLmQ+z0VxoVFaQwkWVKotzpL8wZ
YCOYGAtmxXvqWDiGuhzqG7RVLKW6vj8xz2BFqm5Gf6O32RpV9wFiNp2EtF8Hu+On
sMEqFWDqMbqIwUhcPKRI9+Zhj1TkzwNUawE+EgD4ydYVndYxSpqtn1veFc1Bv1xo
1FbntlDu/AzlPqtIFBzWLZNUxcwW+qKSjOCFlyCs+k1l6CEf+AoZAm1TsL+rVTw=
=3QsX
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A disappointingly large collection of fixes for SPI issues, though
almost all in drivers (and there mainly the newly added Mediatek
driver) and the core fixes are documentation and error handling.
The driver fixes are all of the usual 'important if you see them'
variety"
* tag 'spi-fix-v4.3-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: xtensa-xtfpga: fix register endianness
spi: meson: Fix module autoload for OF platform driver
spi: mediatek: fix wrong error return value on probe
spi: fix kernel-doc warnings in spi.h
spi: spidev: fix possible NULL dereference
spi: atmel: remove warning when !CONFIG_PM_SLEEP
spi: bcm2835: BUG: fix wrong use of PAGE_MASK
spi: mediatek: fix spi cs polarity error
spi: Fix documentation of spi_alloc_master()
spi: spi-pxa2xx: Check status register to determine if SSSR_TINT is disabled
spi: Mediatek: Document devicetree bindings update for spi bus
spi: mediatek: fix spi clock usage error
spi: mediatek: remove clk_disable_unprepare()
The ssd1307fb driver supports a lot of chips from the ssd130xfb series.
This patch adds the ssd1309 chip, a 128x64 OLED driver chip. It is very
similar to the other chips and only has some definitions added to
support it.
Signed-off-by: Olliver Schinagl <o.schinagl@ultimaker.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Added entries in i2c/vendor-prefixes for the us5182d als and proximity sensor.
Also added a documentation file for this sensor's properties.
Signed-off-by: Adriana Reus <adriana.reus@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add support for VZ89X sensors VOC and CO2 reporting channels in
percentage which can be converted to part per million.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
MMA8652FC and MMA8653FC don't provide the transient interrupt source, so
the motion interrupt source is used by providing a new iio_chan_spec
definition, so that other supported devices are not affected by this.
Datasheets for the newly supported devices are available at Freescale's
website:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8652FC.pdfhttp://cache.freescale.com/files/sensors/doc/data_sheet/MMA8653FC.pdf
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This adds support for the 10 bit version if Freescale's accelerometers
of this series. The datasheet is available at Freescale's website:
http://cache.freescale.com/files/sensors/doc/data_sheet/MMA8453Q.pdf
It creates a devicetree bindings file to document the new functionality
and removes the driver from the trivial-devices list.
Signed-off-by: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
These bindings can be used to register Holt HI-8435 threshold detector
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The ar7240 misc irq chip use ack handler
instead of ack_mask handler. All new ath79 chips use
the ar7240 misc irq chip
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Alban Bedel <albeu@free.fr>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-mips@linux-mips.org
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/11164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the Qualcomm Switch-Mode Battery Charger and Boost device tree
binding.
Signed-off-by: Courtney Cavin <courtney.cavin@sonymobile.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Add binding documentation for the usb power supply part of the AXP20x pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Depending on the GIC variant, the GIC module has one or more clock
inputs. Document the optional "clocks" and "clock-names" properties,
and their possible values, based on the Technical Reference Manuals.
optional.
Add the optional "power-domains" property.
This will allow to describe in DT the relationship between the GIC and
the Clock and/or Power Domain topology on SoCs where this is relevant
and needed for proper operation.
Note: As the current GIC driver doesn't support Runtime PM yet, PM
Domain constraints must be handled elsewhere in e.g. platform code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Link: http://lkml.kernel.org/r/1442261204-30931-3-git-send-email-geert%2Brenesas@glider.be
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for the PrimeCell® Generic Interrupt Controller (PL390) to
the GIC DT bindings and driver.
Currently the GIC driver treats this GIC variant the same as other GIC
variants, but there are differences in hardware topology (e.g. clock
inputs).
Sort the list of compatible values while we're at it.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh+dt@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Link: http://lkml.kernel.org/r/1442261204-30931-2-git-send-email-geert%2Brenesas@glider.be
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds devicetree support to mrf24j40 with proper devicetree
compatible strings.
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Add device tree based initialization support for tps65023 regulators.
Therefore add macros for regulator definition setting of_match and
regulators_node members. Add initialization of regulator_desc data
using these macros. Remove old regulator_desc initialization.
Add device tree binding document for tps65023 regulators.
Signed-off-by: Thomas Elste <thomas.elste@imms.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds documentation for the devicetree bindings used by the
DT files of Hisilicon Hip05-D02 development board.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABCgAGBQJV+ysPAAoJEP5prqPJtc/HP4kH/2+WqOYDXkObGQ/dsurcDu1W
kRFNBZHM6m8egD1kqRs8+ipzjrkc7mCN3LUGKOMReXptUlBjS6UOno7ZRNS5dfkt
vDgCaGwCQbGOXlDbPv6OujWRL6MLL4sl1CKhB653ubFJQ75TTw9kPlpL9LdQ0J9R
gBgxT1+hIwbEZeJagByF7EPe8qiQ12f6IOiFXKtsPbLsXTSHxoh8HJxBT6BxPxvF
W3xKVb1YzXEx9ZsmY2uNJCRmDt6PWovwMA34vVBk0mKTFG7VtKplO3o/XiFnKZT/
M0iQNJ0p2sWnchfiHtBMG4KWBsWmd/Bk1tW3fRBTIJz+bRIDYMxIVsT3Gad+fRg=
=JEjX
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.4-20150917' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-09-17
this is a pull request of two patches for net-next/master.
Gerhard Bertelsmann adds support for the CAN controller found on the
Allwinner A10/A20 SoC.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The Hisilicon Network Subsystem is a long term evolution IP which is
supposed to be used in Hisilicon ICT SoC. The IP, which is called hns
for short, is a TCP/IP acceleration engine, which can directly decode
TCP/IP stream and distribute them to different ring buffers.
HNS can be configured to work on different mode for different scenario.
This patch make use only some of the mode to make it as standard
ethernet NIC. The other mode will be added soon.
The whole function has 4 kernel sub-modules:
hnae: the HNS acceleration engine framework. It provides a abstract
interface between the engine and the upper layers which make use of the
engine by ring buffer.
hns_enet_drv: a standard ethernet driver that base on the ring buffer.
hns_dsaf: one of the implementation of HNS acceleration engine, which is
applied on Hililicon hip05, Hi1610 and other later-on SoCs
hns_mdio: the mdio control to the PHY, used by acceleration engine
This submit add basic config and documents
Signed-off-by: huangdaode <huangdaode@hisilicon.com>
Signed-off-by: Kenneth Lee <liguozhu@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All of the Gen3 touchpads are fixed with I2C address 0x67, so correct the
reg value description from 0x24 to 0x67.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devicetree bindings for Allwinner A10/A20 CAN controller.
Signed-off-by: Gerhard Bertelsmann <info@gerhard-bertelsmann.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The bma180 / bma250 accelerometers share a driver (at least under Linux),
so it makes sense to also have their bindings info in a single .txt.
This commit extends the bma180 bindings with bma250 bindings, specifically
it specifies how the 2 seperate interrupts the bma250 has must be listed
in devicetree. The existing bma180 driver is already fully compatible
with the specified bindings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rob Herring <robh@kernel.org>
The cooling-{min,max}-level properties are marked as optional in
Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt and the usage
in various device tree matches this, i.e., some cooling device in the
device trees provide these properties while others do not.
Make the bindings in
Documentation/devicetree/bindings/thermal/thermal.txt consistent with
the cpufreq-dt bindings by marking the cooling-*-level properties as
optional.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The device trees in the kernel as well as the binding description in
Documentation/devicetree/bindings/cpufreq/cpufreq-dt.txt use the
cooling-{min,max}-level property.
Fix the inconsistency with the binding description in
Documentation/devicetree/bindings/thermal/thermal.txt by changing
cooling-*-state properties to cooling-*-level.
Signed-off-by: Punit Agrawal <punit.agrawal@arm.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Rob Herring <robh@kernel.org>
The GICv3 ITS uses sideband master identification data (known as a
DeviceID) to identify which master wrote to a doorbell, and this data is
used to determine how to react in response to the write.
Commit 1e6db00048 ("irqchip/gicv3-its: Add platform MSI support")
added support per this binding, but failed to update the documentation.
This patch fixes the documentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Document the hif-cpubiuctrl node a bit more, and add a documentation
entry for the optional "brcm,write-pairing" property.
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Introduce "regulator-allow-set-load" property to make it possible to
flag in the board configuration that a regulator is allowed to have the
load requirements changed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document a new Device Tree property 'samsung,s2mps11-acokb-ground'
indicating that ACOKB pin of S2MPS11 PMIC is connected to the ground
so the PMIC must manually set PWRHOLD bit in CTRL1 register to turn
off the power.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Explanation of several properties, which allow PWM fan working as a cooling
device, have been embraced in this commit.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Allwinner SoCs have an in-SoC audio controller taking the role of a DAI
and a codec.
Add the binding documentation for that controller on the A10.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch documents the compatible string for APM X-Gene Potenza CPU's PMU.
Signed-off-by: Vinayak Kale <vkale@apm.com>
Signed-off-by: Feng Kan <fkan@apm.com>
Adds DT binding for explicitly choosing a tdm mask for DAI and uses it
in simple-card. The API for snd_soc_of_parse_tdm_slot() has also been
changed.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Document the binding for the zynq specific chipidea UDC binding.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Add the documentation for the Broadcom Northstar Plus device tree
bindings.
Signed-off-by: Jon Mason <jonmason@broadcom.com>
Acked-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Renesas sound has AUDIO_CLKOUT (in Gen1/Gen2) AUDIO_CLKOUT1/2/3 (in Gen3)
This patch support these patches as clock provider.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Renesas sound Gen3 is updated version of Gen2. We need to update
driver for it, but basically it should works as Gen2 compatible.
This is initial support for Gen3. Gen3 specific feature will be
incrementally added in the future
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ak4642 chip can output clock via MCKO pin as audio reference clock.
This patch supports it on DT
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Silk Device tree bindings Documentation, listing it as a supported board.
This allows to use checkpatch to validate DTSes referring to the Silk board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
They have all been eliminated now.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Pull more input updates from Dmitry Torokhov:
"Second round of updates for the input subsystem.
This introduces two brand new touchscreen drivers (Colibri and
imx6ul_tsc), some small driver fixes, and we are no longer report
errors from evdev_flush() as users do not really have a way of
handling errors, error codes that we were returning were not on the
list of errors supposed to be returned by close(), and errors were
causing issues with one of older versions of systemd"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: imx_keypad - remove obsolete comment
Input: touchscreen - add imx6ul_tsc driver support
Input: Add touchscreen support for Colibri VF50
Input: i8042 - lower log level for "no controller" message
Input: evdev - do not report errors form flush()
Input: elants_i2c - extend the calibration timeout to 12 seconds
Input: sparcspkr - fix module autoload for OF platform drivers
Input: regulator-haptic - fix module autoload for OF platform driver
Input: pwm-beeper - fix module autoload for OF platform driver
Input: ab8500-ponkey - Fix module autoload for OF platform driver
Input: cyttsp - remove unnecessary MODULE_ALIAS()
Input: elan_i2c - add ACPI ID "ELAN1000"
Pull watchdog updates from Wim Van Sebroeck:
- new driver for NXP LPC18xx Watchdog Timer
- new driver for SAMA5D4 watchdog timer
- add support for MCP79 to nv_tco driver
- clean-up and improvement of the mpc8xxx watchdog driver
- improvements to gpio-wdt
- at91sam9_wdt clock improvements
... and other small fixes and improvements
* git://www.linux-watchdog.org/linux-watchdog: (25 commits)
Watchdog: Fix parent of watchdog_devices
watchdog: at91rm9200: Correct check for syscon_node_to_regmap() errors
watchdog: at91sam9: get and use slow clock
Documentation: dt: binding: atmel-sama5d4-wdt: for SAMA5D4 watchdog driver
watchdog: add a driver to support SAMA5D4 watchdog timer
watchdog: mpc8xxx: allow to compile for MPC512x
watchdog: mpc8xxx: use better error code when watchdog cannot be enabled
watchdog: mpc8xxx: use dynamic memory for device specific data
watchdog: mpc8xxx: use devm_ioremap_resource to map memory
watchdog: mpc8xxx: make use of of_device_get_match_data
watchdog: mpc8xxx: simplify registration
watchdog: mpc8xxx: remove dead code
watchdog: lpc18xx_wdt_get_timeleft() can be static
DT: watchdog: Add NXP LPC18xx Watchdog Timer binding documentation
watchdog: NXP LPC18xx Watchdog Timer Driver
watchdog: gpio-wdt: ping already at startup for always running devices
watchdog: gpio-wdt: be more strict about hw_algo matching
Documentation: watchdog: at91sam9_wdt: add clocks property
watchdog: booke_wdt: Use infrastructure to check timeout limits
watchdog: (nv_tco) add support for MCP79
...
This is a collection of a few late fixes and other misc. stuff that
had dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates.
There's one conflict with drivers/cpufreq/exynos-cpufreq.c because
it's now been completely removed, but there were some fixes that hit
mainline in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIbBAABAgAGBQJV8fkAAAoJEFk3GJrT+8Zllf8P9jj3+TnvbJS/8bWoQoB7BRUZ
LZPgi2+sBXylrBV60uQdyodiTHQUMZhbL7GvgEVG0z6yyin7nyijqNkulTbQbWmg
WhumLNCNcs8vlZegA/corbwgcVC7FkjOP97HveTe2mgwZ+GaXj9qMRQzBsMqSXEo
4890ZeP1nWBTP42oXOQHkNyKWFBjuERK0dTw2MXj7WE0/Ag8i7ERp76uJQdQ7V5O
BpNRwxp3vSCky8rxbpD/avWdlspv1yZGBQyLeIreVq2YQFojvT36K8wHcf6iWBT/
pzGGV/uZM7MnrGZdqSfVEMDHl7Z2s7Ls+sv5F6Md7ErnVDerHGRjw/6lJDjbeH7u
trucpsuhz5yhTjpZssGHH2NT8pWxxh8M+AaNOiiH8PuYESAbPAmWLpWkn+648bIn
P++Z90DIyfNEqnNSMHkcQYpVt8zc4g75gZfTIIsXLB+DLgzgSK8ergrfyRN/O0zj
oFY35g3wHdgisnGve+BAW30zTZtP19TMT36OltWjIkjuRZC29PS2vkH8eTETdVXx
01f/qcpbB1L1rXfIBjNkjx81j89XPd68JIBfctTF5QBOAGm/Dix6tj2mU/N7TNu5
TrBmD3CXdOQbCPaoK/qWX7/b11IN/XOlGL06hhYwbSdvCVy7rNccApXvfnrDWziK
Ly923FP1OB7h0Kk1cmo=
=85Ck
-----END PGP SIGNATURE-----
Merge tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM SoC updates from Kevin Hilman:
"This is a collection of a few late fixes and other misc stuff that had
dependencies on things being merged from other trees.
The bulk of the changes are for samsung/exynos SoCs for some changes
that needed a few minor reworks so ended up a bit late. The others
are mainly for qcom SoCs: a couple fixes and some DTS updates"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
ARM: multi_v7_defconfig: Enable PBIAS regulator
soc: qcom: smd: Correct fBLOCKREADINTR handling
soc: qcom: smd: Use correct remote processor ID
soc: qcom: smem: Fix errant private access
ARM: dts: qcom: msm8974-sony-xperia-honami: Use stdout-path
ARM: dts: qcom: msm8960-cdp: Use stdout-path
ARM: dts: qcom: msm8660-surf: Use stdout-path
ARM: dts: qcom: ipq8064-ap148: Use stdout-path
ARM: dts: qcom: apq8084-mtp: Use stdout-path
ARM: dts: qcom: apq8084-ifc6540: Use stdout-path
ARM: dts: qcom: apq8074-dragonboard: Use stdout-path
ARM: dts: qcom: apq8064-ifc6410: Use stdout-path
ARM: dts: qcom: apq8064-cm-qs600: Use stdout-path
ARM: dts: qcom: Label serial nodes for aliasing and stdout-path
reset: ath79: Fix missing spin_lock_init
reset: Add (devm_)reset_control_get stub functions
ARM: EXYNOS: switch to using generic cpufreq driver for exynos4x12
cpufreq: exynos: Remove unselectable rule for arm-exynos-cpufreq.o
ARM: dts: add iommu property to JPEG device for exynos4
ARM: dts: enable SPI1 for exynos4412-odroidu3
...
This patch fixes SMEM addressing issues when remote processors need to use
secure SMEM partitions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
The compatible "atmel,sama5d4-wdt" supports the SAMA5D4 watchdog driver
and the watchdog's WDT_MR register can be written more than once.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
The watchdog has an input clock, the slow clock. It is required as it will
not function without it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
This set of changes introduces the beginnings of a new API that's based
around the concept of states that can be atomically applied. Drivers go
to various lengths to implement something similar, which indicates that
the core should really be providing the necessary framework.
On top of that, there is a bit of cleanup as well as improved kerneldoc
and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of SoCs
and a couple of fixes for existing drivers (pca9685, Broadcom Kona and
Atmel HLCDC).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ymH8
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes introduces the beginnings of a new API that's
based around the concept of states that can be atomically applied.
Drivers go to various lengths to implement something similar, which
indicates that the core should really be providing the necessary
framework.
On top of that, there is a bit of cleanup as well as improved
kerneldoc and integration into the device-drivers DocBook.
Regarding drivers there is a new one for the NXP LPC18xx family of
SoCs and a couple of fixes for existing drivers (pca9685, Broadcom
Kona and Atmel HLCDC)"
* tag 'pwm/for-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
ARM: at91: pwm: atmel-hlcdc: Add at91sam9n12 errata
pwm: Add NXP LPC18xx PWM/SCT DT binding documentation
pwm: NXP LPC18xx PWM/SCT driver
pwm-pca9685: Support changing the output frequency
pwm-pca9685: Fix several driver bugs
pwm: kona: Modify settings application sequence
pwm: pca9685: Drop owner assignment
pwm: Add to device-drivers documentation
pwm: Clean up kerneldoc
pwm: Remove useless whitespace
pwm: sysfs: Remove unnecessary padding
pwm: sysfs: Properly convert from enum to string
pwm: Make use of pwm_get_xxx() helpers where appropriate
pwm: Add pwm_get_polarity() helper function
pwm: Constify PWM device where possible
pwm: Add the pwm_is_enabled() helper
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlXoqLgACgkQIXnXXONXEReNCwCghq2EtqGYTvLhupB4bJFCdtA5
ZJMAoIJ+1WIbvGJmBZ/RxehiCl/FjxTl
=+N3y
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI updates from Corey Minyard:
"Most of these have been sitting in linux-next for more than a release,
particularly commit 0fbcf4af7c ("ipmi: Convert the IPMI SI ACPI
handling to a platform device") which is probably the most complex
patch.
That is also the one that changes drivers/acpi/acpi_pnp.c. The change
in that file is only removing IPMI from a "special platform devices"
list, since I convert it to the standard PNP interface. I posted this
one to the ACPI list twice and got no response, and it seems to work
well in my testing, so I'm hoping it's good.
Hidehiro Kawai posted a set of changes that improves the panic time
handling in the IPMI driver.
The rest of the changes are minor bug fixes or cleanups and some
documentation"
* tag 'for-linus-4.3' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi:ssif: Add a module parm to specify that SMBus alerts don't work
ipmi: add of_device_id in MODULE_DEVICE_TABLE
ipmi: Compensate for BMCs that wont set the irq enable bit
ipmi: Don't call receive handler in the panic context
ipmi: Avoid touching possible corrupted lists in the panic context
ipmi: Don't flush messages in sender() in run-to-completion mode
ipmi: Factor out message flushing procedure
ipmi: Remove unneeded set_run_to_completion call
ipmi: Make some data const that was only read
ipmi: constify SSIF ACPI device ids
ipmi: Delete an unnecessary check before the function call "cleanup_one_si"
char:ipmi - Change 1 to true for bool type variables during initialization.
impi:Remove unneeded setting of module owner to THIS_MODULE in the platform structure, powernv_ipmi_driver
ipmi: Add a comment in how messages are delivered from the lower layer
ipmi/powernv: Fix potential invalid pointer dereference
ipmi: Convert the IPMI SI ACPI handling to a platform device
ipmi: Add device tree bindings information
This time the IOMMU updates are mostly cleanups or fixes. No big new
features or drivers this time. In particular the changes include:
* Bigger cleanup of the Domain<->IOMMU data structures and the
code that manages them in the Intel VT-d driver. This makes
the code easier to understand and maintain, and also easier to
keep the data structures in sync. It is also a preparation
step to make use of default domains from the IOMMU core in the
Intel VT-d driver.
* Fixes for a couple of DMA-API misuses in ARM IOMMU drivers,
namely in the ARM and Tegra SMMU drivers.
* Fix for a potential buffer overflow in the OMAP iommu driver's
debug code
* A couple of smaller fixes and cleanups in various drivers
* One small new feature: Report domain-id usage in the Intel
VT-d driver to easier detect bugs where these are leaked.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=yoGE
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates for from Joerg Roedel:
"This time the IOMMU updates are mostly cleanups or fixes. No big new
features or drivers this time. In particular the changes include:
- Bigger cleanup of the Domain<->IOMMU data structures and the code
that manages them in the Intel VT-d driver. This makes the code
easier to understand and maintain, and also easier to keep the data
structures in sync. It is also a preparation step to make use of
default domains from the IOMMU core in the Intel VT-d driver.
- Fixes for a couple of DMA-API misuses in ARM IOMMU drivers, namely
in the ARM and Tegra SMMU drivers.
- Fix for a potential buffer overflow in the OMAP iommu driver's
debug code
- A couple of smaller fixes and cleanups in various drivers
- One small new feature: Report domain-id usage in the Intel VT-d
driver to easier detect bugs where these are leaked"
* tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (83 commits)
iommu/vt-d: Really use upper context table when necessary
x86/vt-d: Fix documentation of DRHD
iommu/fsl: Really fix init section(s) content
iommu/io-pgtable-arm: Unmap and free table when overwriting with block
iommu/io-pgtable-arm: Move init-fn declarations to io-pgtable.h
iommu/msm: Use BUG_ON instead of if () BUG()
iommu/vt-d: Access iomem correctly
iommu/vt-d: Make two functions static
iommu/vt-d: Use BUG_ON instead of if () BUG()
iommu/vt-d: Return false instead of 0 in irq_remapping_cap()
iommu/amd: Use BUG_ON instead of if () BUG()
iommu/amd: Make a symbol static
iommu/amd: Simplify allocation in irq_remapping_alloc()
iommu/tegra-smmu: Parameterize number of TLB lines
iommu/tegra-smmu: Factor out tegra_smmu_set_pde()
iommu/tegra-smmu: Extract tegra_smmu_pte_get_use()
iommu/tegra-smmu: Use __GFP_ZERO to allocate zeroed pages
iommu/tegra-smmu: Remove PageReserved manipulation
iommu/tegra-smmu: Convert to use DMA API
iommu/tegra-smmu: smmu_flush_ptc() wants device addresses
...
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJV7WBfAAoJEP4mhCVzWIwpzMMQAISg3SvN116lxgPJsFmx2Oxd
fiSdksUTrGB4/Ya/gTGyFQx5wOep1Y/yLhuQr+2rDbIPlIFiKQuQCEVXERXy5VJl
rmsekgIrMPamiGGYBM5b6n/UhWYktLqoGc88irKYPIaIjLQeH3iqB83y04R6BqBR
tOC4PKnnHaJyJMt1oR/xHi1PjFKX4/WQtnCUlvzUMu8XcrXRwqgWb/hw1QXLUUZa
3npFLxlSqJVXJxtjRSeYZp5juvt+l03rK9h/jNmoDfPl7WtdwxkHtShsnS8b74lF
ZMhrl3phpyMdPNZ0pCwrQJxhplg0MB0Ey8TErRLBsp90Fre0tedf2w6RElkSXek8
tApr6I/Fkydu5ILnNhnhswsbp4rc9tC7kfr5RkPKQF0icEcZFxNblrDtbD/jFYSu
csIZO3xsJTvo4Z7kjYymTn3UpsV8l/hZDNOWHzt7LCTt8X2otEvsLvmabK9pMayI
FipP3pbsM4/H70eOOwpWmzM4J4FGRtKGEXqJGfODqlGHlrXz06xtlvBDzDvW86BA
hFr3cuDPqpMSm9UUPIVYZrm4OuO6p1JpVpj7/cmg48mJEqVNQZ+hyHC0zU2F/saL
4pogQC1vL4SM4xJB+rY4Fo+E7gNEkYjEymEJ4yCbwdqF9Nxjs7m2rCulty4JCVyY
vwMt5mo0d2IsixclFghh
=wR1C
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fix a race condition in the request handling
- Skip trim commands for some buggy kingston eMMCs
- An optimization and a correction for erase groups
- Set CMD23 quirk for some Sandisk cards
MMC host:
- sdhci: Give GPIO CD higher precedence and don't poll when it's used
- sdhci: Fix DMA memory leakage
- sdhci: Some updates for clock management
- sdhci-of-at91: introduce driver for the Atmel SDMMC
- sdhci-of-arasan: Add support for sdhci-5.1
- sdhci-esdhc-imx: Add support for imx7d which also supports HS400
- sdhci: A collection of fixes and improvements for various sdhci hosts
- omap_hsmmc: Modernization of the regulator code
- dw_mmc: A couple of fixes for DMA and PIO mode
- usdhi6rol0: A few fixes and support probe deferral for regulators
- pxamci: Convert to use dmaengine
- sh_mmcif: Fix the suspend process in a short term solution
- tmio: Adjust timeout for commands
- sunxi: Fix timeout while gating/ungating clock"
* tag 'mmc-v4.3' of git://git.linaro.org/people/ulf.hansson/mmc: (67 commits)
mmc: android-goldfish: remove incorrect __iomem annotation
mmc: core: fix race condition in mmc_wait_data_done
mmc: host: omap_hsmmc: remove CONFIG_REGULATOR check
mmc: host: omap_hsmmc: use ios->vdd for setting vmmc voltage
mmc: host: omap_hsmmc: use regulator_is_enabled to find pbias status
mmc: host: omap_hsmmc: enable/disable vmmc_aux regulator based on previous state
mmc: host: omap_hsmmc: don't use ->set_power to set initial regulator state
mmc: host: omap_hsmmc: avoid pbias regulator enable on power off
mmc: host: omap_hsmmc: add separate function to set pbias
mmc: host: omap_hsmmc: add separate functions for enable/disable supply
mmc: host: omap_hsmmc: return error if any of the regulator APIs fail
mmc: host: omap_hsmmc: remove unnecessary pbias set_voltage
mmc: host: omap_hsmmc: use mmc_host's vmmc and vqmmc
mmc: host: omap_hsmmc: use the ocrmask provided by the vmmc regulator
mmc: host: omap_hsmmc: cleanup omap_hsmmc_reg_get()
mmc: host: omap_hsmmc: return on fatal errors from omap_hsmmc_reg_get
mmc: host: omap_hsmmc: use devm_regulator_get_optional() for vmmc
mmc: sdhci-of-at91: fix platform_no_drv_owner.cocci warnings
mmc: sh_mmcif: Fix suspend process
mmc: usdhi6rol0: fix error return code
...
Pull i2c updates from Wolfram Sang:
"Features:
- new drivers: Renesas EMEV2, register based MUX, NXP LPC2xxx
- core: scans DT and assigns wakeup interrupts. no driver changes needed.
- core: some refcouting issues fixed and better API for that
- core: new helper function for best effort block read emulation
- slave framework: proper DT bindings and userspace instantiation
- some bigger work for xiic, pxa, omap drivers
.. and quite a number of smaller driver fixes, cleanups, improvements"
* 'i2c/for-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (65 commits)
i2c: mux: reg Change ioread endianness for readback
i2c: mux: reg: fix compilation warnings
i2c: mux: reg: simplify register size checking
i2c: muxes: fix leaked i2c adapter device node references
i2c: allow specifying separate wakeup interrupt in device tree
of/irq: export of_get_irq_byname()
i2c: xgene-slimpro: dma_mapping_error() doesn't return an error code
i2c: Replace I2C_CROS_EC_TUNNEL dependency
eeprom: at24: use i2c_smbus_read_i2c_block_data_or_emulated
i2c: core: Add support for best effort block read emulation
i2c: lpc2k: add driver
i2c: mux: Add register-based mux i2c-mux-reg
i2c: dt: describe generic bindings
i2c: slave: print warning if slave flag not set
i2c: support 10 bit and slave addresses in sysfs 'new_device'
i2c: take address space into account when checking for used addresses
i2c: apply DT flags when probing
i2c: make address check indpendent from client struct
i2c: rename address check functions
i2c: apply address offset for slaves, too
...
Core:
- use is_visible() to control sysfs attributes
- switch wakealarm attribute to DEVICE_ATTR_RW
- make rtc_does_wakealarm() return boolean
- properly manage lifetime of dev and cdev in rtc device
- remove unnecessary device_get() in rtc_device_unregister
- fix double free in rtc_register_device() error path
New drivers:
- NXP LPC24xx
- Xilinx Zynq MP
- Dialog DA9062
Subsystem wide cleanups:
- fix drivers that consider 0 as a valid IRQ in client->irq
- Drop (un)likely before IS_ERR(_OR_NULL)
- drop the remaining owner assignment for i2c_driver and platform_driver
- module autoload fixes
Drivers:
- 88pm80x: add device tree support
- abx80x: fix RTC write bit
- ab8500: Add a sentinel to ab85xx_rtc_ids[]
- armada38x: Align RTC set time procedure with the official errata
- as3722: correct month value
- at91sam9: cleanups
- at91rm9200: get and use slow clock and cleanups
- bq32k: remove redundant check
- cmos: century support, proper fix for the spurious wakeup
- ds1307: cleanups and wakeup irq support
- ds1374: Remove unused variable
- ds1685: Use module_platform_driver
- ds3232: fix WARNING trace in resume function
- gemini: fix ptr_ret.cocci warnings
- mt6397: implement suspend/resume
- omap: support internal and external clock enabling
- opal: Enable alarms only when opal supports tpo
- pcf2127: use OFS flag to detect unreliable date and warn the user
- pl031: fix typo for author email
- rx8025: huge cleanup and fixes
- sa1100/pxa: share common code
- s5m: fix to update ctrl register
- s3c: fix clocks and wakeup, cleanup
- sirfsoc: use regmap
- nvram_read()/nvram_write() functions for cmos, ds1305, ds1307, ds1343,
ds1511, ds1553, ds1742, m48t59, rp5c01, stk17ta8, tx4939
- use rtc_valid_tm() error code when reading date/time instead of 0 for
isl12022, pcf2123, pcf2127
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cKuu
-----END PGP SIGNATURE-----
Merge tag 'rtc-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"Core:
- use is_visible() to control sysfs attributes
- switch wakealarm attribute to DEVICE_ATTR_RW
- make rtc_does_wakealarm() return boolean
- properly manage lifetime of dev and cdev in rtc device
- remove unnecessary device_get() in rtc_device_unregister
- fix double free in rtc_register_device() error path
New drivers:
- NXP LPC24xx
- Xilinx Zynq MP
- Dialog DA9062
Subsystem wide cleanups:
- fix drivers that consider 0 as a valid IRQ in client->irq
- Drop (un)likely before IS_ERR(_OR_NULL)
- drop the remaining owner assignment for i2c_driver and
platform_driver
- module autoload fixes
Drivers:
- 88pm80x: add device tree support
- abx80x: fix RTC write bit
- ab8500: Add a sentinel to ab85xx_rtc_ids[]
- armada38x: Align RTC set time procedure with the official errata
- as3722: correct month value
- at91sam9: cleanups
- at91rm9200: get and use slow clock and cleanups
- bq32k: remove redundant check
- cmos: century support, proper fix for the spurious wakeup
- ds1307: cleanups and wakeup irq support
- ds1374: Remove unused variable
- ds1685: Use module_platform_driver
- ds3232: fix WARNING trace in resume function
- gemini: fix ptr_ret.cocci warnings
- mt6397: implement suspend/resume
- omap: support internal and external clock enabling
- opal: Enable alarms only when opal supports tpo
- pcf2127: use OFS flag to detect unreliable date and warn the user
- pl031: fix typo for author email
- rx8025: huge cleanup and fixes
- sa1100/pxa: share common code
- s5m: fix to update ctrl register
- s3c: fix clocks and wakeup, cleanup
- sirfsoc: use regmap
- nvram_read()/nvram_write() functions for cmos, ds1305, ds1307,
ds1343, ds1511, ds1553, ds1742, m48t59, rp5c01, stk17ta8, tx4939
- use rtc_valid_tm() error code when reading date/time instead of 0
for isl12022, pcf2123, pcf2127"
* tag 'rtc-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (90 commits)
rtc: abx80x: fix RTC write bit
rtc: ab8500: Add a sentinel to ab85xx_rtc_ids[]
rtc: ds1374: Remove unused variable
rtc: Fix module autoload for OF platform drivers
rtc: Fix module autoload for rtc-{ab8500,max8997,s5m} drivers
rtc: omap: Add external clock enabling support
rtc: omap: Add internal clock enabling support
ARM: dts: AM437x: Add the internal and external clock nodes for rtc
rtc: s5m: fix to update ctrl register
rtc: add xilinx zynqmp rtc driver
devicetree: bindings: rtc: add bindings for xilinx zynqmp rtc
rtc: as3722: correct month value
ARM: config: Switch PXA27x platforms to use PXA RTC driver
ARM: mmp: remove unused RTC register definitions
ARM: sa1100: remove unused RTC register definitions
rtc: sa1100/pxa: convert to run-time register mapping
ARM: pxa: add memory resource to SA1100 RTC device
rtc: pxa: convert to use shared sa1100 functions
rtc: sa1100: prepare to share sa1100_rtc_ops
rtc: ds3232: fix WARNING trace in resume function
...
This reverts commit 5163fb6254
("ahci: added support for Freescale AHCI sata")
The reverted patch added Freescale QorIQ AHCI sata support to
ahci_platform driver though, but it left SoC specific settings to uboot.
It leads to QorIQ sata heavily depending on uboot. In order to removing
the dependency we first revert the old patch and then will add a new driver
for QorIQ SATA.
Since there are no LS* platforms that have been upstreamed, So
the revert would not break anything exists.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
Freescale i.MX6UL contains a internal touchscreen controller,
this patch add a driver to support this controller.
Signed-off-by: Haibo Chen <haibo.chen@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Colibri Vybrid VF50 module supports 4-wire touchscreens using
FETs and ADC inputs. This driver uses the IIO consumer interface
and relies on the vf610_adc driver based on the IIO framework.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
rtc can either be supplied from internal 32k clock or external crystal
generated 32k clock. Internal clock is SOC specific and the external
clock is board dependent. Adding the corresponding nodes.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
adds file for description on device node bindings for RTC
found on Xilinx Zynq Ultrascale+ MPSoC.
Signed-off-by: Suneel Garapati <suneel.garapati@xilinx.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
