Peripheral clock is named pclk and system clock is named hclk (those are
the names expected by the at91_udc driver).
Drop the deprecated usb_clk (formerly used to configure the usb clock rate
which is now directly configurable through hclk).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Some at91 SoCs embed a 10/100 Mbit Ethernet IP, that is based on the
at91sam9260 SoC.
Fix at91 DTs accordingly.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Radxa Rock board most supplies come from the static 5v vsys supply, but
the inl1-supply comes from the REG4 of the act8846 itself. Model this dependency
using the added supply-handling to make sure the supplying regulator gets handled
correctly and not accidentially turned off.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The switches on r8a73a4/ape6evm do not have pull-up registers. The
schematics say: "Need to use APE6 internal PullUp", hence enable pull-up
using pinctrl.
Without this, the switches don't really work, as the GPIO inputs are
more likely to pick up ghost signals through capacitive coupling than
actual keypresses.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
DCAN1 RX and TX lines are internally pulled high according to [1].
While muxing between DCAN mode and SAFE mode we make sure
that the same pull direction is set to minimize opposite
pull contention during the switching window.
[1] in DRA7 data manual, Ball characteristics table 4-2, DSIS colum shows
the state driven to the peripheral input while in the deselcted mode.
DSIS - De-Selected Input State.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rev.F onwards ball G19 (dcan1_rx) is used as a GPIO for some other
function so don't include it in DCAN pinctrl node.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP4 has a finer counter granularity, which allows for a delay of 1000ms
in the thermal zone polling intervals. OMAP5 has a different counter
mechanism, which allows at maximum a 500ms timer. Adjust the cpu thermal
zone polling interval accordingly.
Without this patch, the polling interval information is simply ignored,
and the following thermal warnings are printed during boot (assuming
thermal is enabled);
[ 1.545343] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.552691] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
[ 1.560029] ti-soc-thermal 4a0021e0.bandgap: Delay 1000 ms is not supported
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use external clock for RMII since the internal clock doesn't meet the
jitter requirements.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Beaglebone Black doesn't have AES and SHAM enabled like the
original Beaglebone White dts. This breaks applications that
leverage the crypto blocks so fix this by enabling these nodes
in the am335x-bone-common.dtsi. With this change, enabling the
nodes in am335x-bone.dts is no longer required so remove them.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 4da1c67719 ("add tbclk data for ehrpwm")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ehrpwm tbclk is wrongly modelled as deriving from dpll_per_m2_ck.
The TRM says tbclk is derived from SYSCLKOUT. SYSCLKOUT nothing but the
functional clock of pwmss (l4ls_gclk).
Fix this by changing source of ehrpwmx_tbclk to l4ls_gclk.
Fixes: 9e100ebafb: ("Fix ehrpwm tbclk data")
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes 85dc74e9 (ARM: dts: omap5 clock data)
On OMAP54xx, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA,
DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fixes: ee6c750761 (ARM: dts: dra7 clock data)
On DRA7x, For DPLL_IVA, the ref clock(CLKINP) is connected to sys_clk1 and
the bypass input(CLKINPULOW) is connected to iva_dpll_hs_clk_div clock.
But the bypass input is not directly routed to bypass clkout instead
both CLKINP and CLKINPULOW are connected to bypass clkout via a mux.
This mux is controlled by the bit - CM_CLKSEL_DPLL_IVA[23]:DPLL_BYP_CLKSEL
and it's POR value is zero which selects the CLKINP as bypass clkout.
which means iva_dpll_hs_clk_div is not the bypass clock for dpll_iva_ck
Fix this by adding another mux clock as parent in bypass mode.
This design is common to most of the PLLs and the rest have only one bypass
clock. Below is a list of the DPLLs that need this fix:
DPLL_IVA, DPLL_DDR,
DPLL_DSP, DPLL_EVE,
DPLL_GMAC, DPLL_PER,
DPLL_USB and DPLL_CORE
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
lcdck takes mck (not smd) as its parent. It is also assigned id 3 and not 4.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: squashed 2 related patches]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Rename lcd_clk into lcdc_clk to be consistent with sama5d3 clock
definitions.
Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=1m2R
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Pull "Renesas ARM Based SoC DT Updates for v4.1" from Simon Horman:
* Increase hardware coverage of DT for various SoCs
* Add PFC information for emev2 SoC
* Remap entire APMU region for r8a7791 and r8a7790 SoCs
* Declare the full 512 MiB of RAM for kzm9g board
* Add selectable sources to DIV6 clocks to sh73a0 SoC
* Add missing INTCA0 clock for irqpin module on sh73a0 SoC
* Set control-parent for all irqpin node on sh73a0 SoC
* tag 'renesas-dt-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
ARM: shmobile: r8a7794: add SDHI DT support
ARM: shmobile: r8a7790: add ADSP clocks
ARM: shmobile: r8a7791: add ADSP clocks
ARM: shmobile: henninger: add CAN0 DT support
ARM: shmobile: r8a7791: add CAN DT support
ARM: shmobile: r8a7791: add CAN clocks
ARM: shmobile: r8a7790: add CAN DT support
ARM: shmobile: r8a7790: add CAN clocks
ARM: shmobile: emev2-kzm9d dts: Add PFC information for uart1
ARM: shmobile: emev2 dtsi: Add PFC information
ARM: shmobile: r8a7791: smp: remap whole apmu region
ARM: shmobile: r8a7790: smp: remap whole apmu region
ARM: shmobile: koelsch: Add DU HDMI output support
ARM: shmobile: r8a7791: Correct SDHI clock labels and output-names
ARM: shmobile: r8a7794: Correct SDHI clock base address, labels and output-names
ARM: shmobile: r8a7794: alt: Enable ethernet controller
ARM: shmobile: r8a7794: Add ethernet controller to device tree
ARM: shmobile: r8a7794: Add IPMMU DT nodes
ARM: shmobile: r8a7791: Add IPMMU DT nodes
ARM: shmobile: r8a7790: Add IPMMU DT nodes
...
* Remove the sh7372 SoC and its mackerel board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Lpw8
-----END PGP SIGNATURE-----
Merge tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/multiplatform
Pull "Renesas ARM Based SoC sh7372 SoC Removal Updates for v4.1" from Simon Horman:
* Remove the sh7372 SoC and its mackerel board
* tag 'renesas-sh7372-soc-removal-for-v4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
Documentation: Remove ZBOOT MMC/SDHI utility and docs
ARM: shmobile: sh7372 dtsi: Remove Legacy DTSI file
ARM: shmobile: sh7372: Remove DT binding documentation
ARM: shmobile: sh7372: Remove Legacy C SoC code
ARM: shmobile: sh7372: Remove ZBOOT MMC/SDHI support
ARM: shmobile: mackerel: Remove from MAINTAINERS
ARM: shmobile: mackerel: Remove defconfig
ARM: shmobile: mackerel: Remove mach-type entry
ARM: shmobile: mackerel: Remove DT binding documentation
ARM: shmobile: mackerel dts: Remove Legacy DTS file
ARM: shmobile: mackerel: Remove Legacy C board code
ARM: shmobile: mackerel: Remove ZBOOT code
[arnd: The sh7372 platform is rather dated and is believed to
have no active users on modern kernels. It stands in the way
of converting all of mach-shmobile to be multiplatform capable,
as adding pinctrl and common-clock support for it would be more
work than it's worth. As always, should any legitimate upstream
users show up in the future, we will revert this removal]
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJU9uKaAAoJEAf03oE53VmQrT4IAID5RZZLycH65MfI2SWs5jHJ
riXpp2ByX2YMZhBV7Y+jSJcdty0zdZFXAm3cME8YtHSHFNW87y3U90BhL1JTwFh8
Rlk45xxauRmiH5R+0haBIavt+ZFHB8QOgmAE+xa4Vc/qBiry6HSgWVldk3yiai5j
Mnq/+UpeL7mSlcn9kFkbVVOkDiP2tRoITU0z780tBgywbUQEluNZan4MfjSaknzP
GEwmN74Z6QPUxhqc1Z1ACU84ozYcLYaiMksNXrTch0+dLz91MIRl6Eqb53XhJEK3
P8ysCj16UBgX2JuuYWBGkxrZ1Brl0Lj5075JrM+He0T/XRsLTChb+9rQ14QrKno=
=YpBm
-----END PGP SIGNATURE-----
Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes
Merge "First fixes batch for AT91 on 4.0" from Nicolas Ferre:
- PM slowclock fixes for DDR and timeouts
- fix some DT entries
- little defconfig updates
- the removal of a harmful watchdog option + its detailed documentation
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: keep watchdog running in idle mode
dts: Documentation: AT91 Watchdog, explain what atmel,idle-halt property really do
ARM: at91/defconfig: add at91rm9200 ethernet support
ARM: at91/defconfig: remove CONFIG_SYSFS_DEPRECATED
ARM: at91/dt: at91sam9260: fix usart pinctrl
ARM: at91/dt: sama5d4: add missing alias for i2c0
ARM: at91/dt: at91sam9263: Fixup sram1 device tree node
ARM: at91: pm: fix SRAM allocation
ARM: at91: pm: fix at91rm9200 standby
pm: at91: Workaround DDRSDRC self-refresh bug with LPDDR1 memories.
pm: at91: pm_slowclock: fix suspend/resume hang up in timeouts
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbWq
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into fixes
Merge "Samsung tmu and hdmi regression fixes for v4.0" from Kukjin Kim:
- The thermal management unit and HDMI (drm mixer driver) related
reworks have been merged in v4.0 merge window. So if this DT changes
are missed for v4.0, we regressions in v4.0 release for exynos
platforms such as exynos5250, exynos5420, exynos4 SoCs.
- Note since there was a dependency with driver side, this cannot
be sent to upstream during preivous merge window and now it has been
resolved.
* tag 'samsung-fixes-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: add display power domain for exynos5250
ARM: dts: add 'hdmi' clock to mixer nodes for exynos5250 and exynos5420
ARM: dts: enable hdmi support for exynos4210-universal_c210
ARM: dts: enable hdmi support for exynos4412-odroid-common
ARM: dts: add dependency between TV and LCD0 power domains for exynos4
ARM: dts: add hdmi related nodes for exynos4 SoCs
ARM: EXYNOS: add support for sub-power domains
dt-bindings: document a note about power domain subdomains
ARM: dts: Provide dt bindings identical for Exynos TMU
ARM: dts: Trip points and sensor configuration data for exynos5440
ARM: dts: define default thermal-zones for exynos4
ARM: dts: default trip points definition for exynos5420
ARM: dts: add TMU default definitions for exynos4412
ARM: dts: Adding CPU cooling binding for Exynos SoCs
ARM: dts: Enable TMU for exynos4412-odriod-common
ARM: dts: Add LDO10 for TMU for exynos4412-odroid-common
ARM: dts: Enable TMU for exynos4210-trats
PopMetal is a rockchip rk3288 based board made by ChipSpark,
which has many interface such as VGA,HDMI,usb,ir,sdcad and lots of
sensors such as gyroscope(L3G4200D),accelerometer(mma8452),
compass(AK8963C).
This patch add a basic support for this board, which make the board
boot into a initramfs shell with sdcard,hdmi and all sensors enabled
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
socfpga.dtsi is missing the DMA channels for the uart nodes.
This will produce the following errors:
of_dma_request_slave_channel: dma-names property of node '/soc/serial0@ffc02000' missing or empty
ttyS0 - failed to request DMA
Provide the correct DMA channels to fix this.
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
macb0 DT node can have phy child nodes, so add the #{address,
size}_cells for macb0 node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the leds DT node in the dts file.
In the leds, d10 is set as heartbeat led.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add alias, node declaration and pinctrl for i2c1 (aka: twi1).
Signed-off-by: Philip Attfield <phil.attfield@seqlabs.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Gpio-keys nodes are not using the "reg" property in their sub nodes.
So, there is no need to define #address-cells and #size-cells properties
in gpio-keys nodes: we remove them in these new boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
File name had at91 prefix, which is not the case anymore for SAMA5D3.
AT91SAM9x5 was mentioned instead of SAMA5D3 SoC.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable ISI and ov2640 for at91sam9g25ek board.
Meantime, we need to disable the mmc1 and spi0 as they have pin conflict
with ISI.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add the camera sensor ov2640 dt support. And connect sensor to isi node
as well.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a new file: at91sam9x5_isi.dtsi, which includes ISI node and
pinctrls.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This commit adds the Device Tree files for the Armada 39x family of
processors, as well as one Armada 398 Development Board.
Like for other Marvell EBU families, a common armada-39x.dtsi contains
the description of the common features of all Armada 39x SoCs, while
armada-390.dtsi and armada-398.dtsi respectively describe the
specificities of those SoCs.
Finally, an armada-398-db.dts file is added to describe the Armada 398
Development Board itself.
So far, the following features are supported:
* SMP: dual Cortex-A9
* Basic ARM IPs: SCU, timer, GIC, L2 cache
* Basic Marvell IPs: pin-muxing, clocks, system controller, MBus
controller, MPIC interrupt controller, timer, CPU reset for SMP,
PMSU.
* I2C
* SPI
* SDHCI
* XOR
* NAND
* UART
* PCIe
Additional features will be supported in the future.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Device Tree nodes describing the MPIC nodes on Armada 370, 375,
38x and XP had a unit address that did not match the first reg
property, as suggested by the ePAPR. This commit fixes that.
[gregory.clement@free-electrons.com: removed the armada-38x part, as it
was already applied by a previous patch]
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the stdout-path property in /chosen for all Armada
boards that were not yet carrying this property, and gets rid of
/chosen/bootargs which becomes unneeded: earlyprintk should not be
used by default, and the console= parameter is replaced by the
/chosen/stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds 'serialX' aliases for the various serial ports on
Armada 370, 375, 38x and XP platforms. It will allow the usage of the
stdout-path property.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Having aliases for Ethernet devices is useless, since the networking
subsystem unfortunately doesn't care about aliases to name network
interfaces.
Note that the 'aliases' nodes in armada-370-xp.dtsi and armada-xp.dtsi
become empty, but that we keep it as is since a followup patch will
re-add some aliases to it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds the standard uart0 and uart1 DT labels to the Device
Tree description of the Marvell Armada 375 SoC.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 38x had a label for UART0, but not UART1. This commit fixes
that.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On Marvell Armada 38x, the USB2 controller registers are at 0x58000,
so the corresponding Device Tree node should have a unit address of
58000, and not 50000. We were using 50000 due to an incorrect
copy/pastebin of Armada 370/XP code.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development Board has a 1GB NAND SLC chip from
Micron as its main storage. Enable it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Add a DSA section to the DT blob representing the Ethernet switch.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
On the LaCie 2Big Network v2 (net2big_v2) board, the fan alarm is not
wired to the I2C fan controller but to a separe GPIO. This GPIO can be
controlled by using the gpio-fan driver.
This patch adds the gpio-fan alarm description in the net2big_v2 DTS.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The unit-address is supposed to be equal the first reg address, which is not
the case for the MPIC, that uses the mbus-controller one. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This add common pinctrl settings for pcie[01]_clkreq, spi1, i2c[23],
and internal i2c mux. These settings have either one or two options
only, so put them into the SoC dtsi instead of repeating them on
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Since turning on idle-halt in commit fe46aa679f (ARM: at91/dt: add
sam9 watchdog default options to SoCs), SoCs compatible with at91sam9260-wdt
no longer reboot if the watchdog times out while the CPU is in idle state.
Removing the 'idle-halt' flag that was set by default fixes this.
Signed-off-by: Michel Marti <mma@objectxp.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
[nicolas.ferre@atmel.com: rework the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Corrected pins used by usart3.
Signed-off-by: Jonas Andersson <jonas@microbit.se>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Commit ff04660e48b20 ("ARM: at91/dt: add SRAM nodes") used the same base
address for sram0 and sram1 leading to the following warning:
WARNING: CPU: 0 PID: 1 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x50/0x70()
sysfs: cannot create duplicate filename '/devices/platform/300000.sram'
Fix the base address for sram1.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
DT file to enable the Wireless Audio reference design based on the
BCM58305.
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Tested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Jonathan Richardson <jonathar@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add a DTS file for MINIX NEO-X8, a Meson8-based digital media player.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add pinctrl node to the DTSI file for meson8 and sub-nodes for some
standard mux configurations.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Add a node for the Ethernet controller to Meson DTS file and
enable it on the Geniatech ATV1200 board.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
This adds a node for the SPI Flash Controller to the Amlogic Meson
DTS.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Mark Brown <broonie@kernel.org>
The PHY IRQ line is connected to external IRQ8, not IRQ0. Fix DT
accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds sound card using the ak4643 codec.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds an entry for an R-Car Gen. 1 sound controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[horms: Removed undocumented "renesas,rcar_sound" compat string]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 148.5MHz pixel clocks connected to the DU clock
inputs.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declare the fixed 65MHz pixel clock connected to the DU clock input.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While the LEDs on r8a73a4/ape6evm are tied to VSUPPLY, they're driven by
an N-channel MOSFET. Hence the GPIO signal should be active high.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sets the extal clock to the frequency of the oscillator installed by
default (33 MHz).
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node to the new BSC node, as its connected to the
Bus State Controller.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: dropped compat string changes as they seem out of scope]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On Peach Pit and Pi boards, the Exynos SoC XCLKOUT pin provides
master clock (mclk) to the codec. So make it a clock consumer.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Peach Pit and Pi boards have a WiFi module that is always powered
but needs toggling an enable pin and ungating a 32kHz reference
clock as part of their power sequencing.
Add a dev node for the SDIO slot and a MMC power sequence provider.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 SoC has 3 sets of 8 pads used as data lines for the 3
MMC/SD/SDIO slots. These needs to be muxed as SD_n_DATA instead of a
GPIO or external interrupt to allow the MMC controller to communicate
with the attached cards or SDIO devices.
Which data lines needs to be muxed as SD_n_DATA depends on the bus
width used for data transfer:
* bus-width = <1> needs SD_n_DATA[0]
* bus-width = <4> needs SD_n_DATA[0-3]
* bus-width = <8> needs SD_n_DATA[0-7]
The Exynos5250-pinctrl.dtsi file that defines the groups of pins has
SD_n_DATA[0] muxed for both sdn_bus1 and sdn_bus4 so just one of them
needs to be included in the device node's pinctrl property.
But Exynos5420-pinctrl has a different definition and only includes
SD_n_DATA[1-3] for sdn_bus4. So for a bus-width = <4>, both sdn_bus1
and sdn_bus4 have to be in the dev pinctrl to mux all the needed pads.
It seems all Exynos5420 boards had just cargo cult the pinctrl lines
assuming that sdn_bus4 also included SD_n_DATA[0] and it only works
because the bootloader muxes the pads correctly. But that is not the
case for the devices not used by the bootloader such as WiFi modules.
Add sdn_bus1 too in the nodes pinctrl to not rely on the bootloader.
Suggested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The patch adds domain definition and references to it in appropriate devices.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
[mszyprow: rebased onto generic power domains dt bindings]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Mixed block needs to control hdmi clock to properly perform power on/off
operation, so add 'hdmi' clock also to mixer nodes.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds configuration of hw modules required to enable HDMI
support on Universal C210 board.
Signed-off-by: Tomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds nodes specific to Exynos4412 based Odroid X/X2/U2/U3
boards required for enabling HDMI display.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
TV Mixer needs both TV and LCD0 domains enabled to be fully operational.
This dependency is modelled by making TV power domains a sub-domain of
LCD0 power domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds entries for HDMI, Mixer and i2c with hdmi-phy modules
found in Exynos 4210 and 4x12 SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented device tree bindings provide data already hardcoded in the
exynos_tmu_data.c file.
After this commit, it should be possible to reuse common thermal core
framework in Exynos SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit provides information about Exynos5440 device configuration.
Previously this information was available in exynos_tmu_data.c file.
Now it is available in the device tree.
Such approach allows reusing some common code for thermal.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Trip points corresponding to the one defined in the exynos_tmu_data.c
for Exynos4 have been included.
This thermal-zones attribute is afterwards reused for Exynos4210,
Exynos4412 and Exynos5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This code groups in one place default settings of trip points.
It is used in SoCs with multiple instances of TMU sensor.
Separate device tree file prevents from multiple copying of the
same data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Exynos 4 and 5 family of SoCs uses almost identical TMU sensor to
measure the on chip temperature. For this reason it is possible to
group TMU configuration parameters in one dts file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Presented patch aims to move data necessary for correct CPU cooling device
configuration from exynos_tmu_data.c to device tree.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This commit enables TMU IP block on the Exynos4412 Odroid based
devices such as Odroid U3.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The thermal IP block (Thermal Management Unit) called TMU has been
enabled in this device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add pcie[01] node labels to allow to reference them easily from
board level.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
We want to enforce the use of named flags in GPIO and interrupt
specifiers, include the corresponding headers to Dove's SoC dtsi.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fix Dove's register addresses of uart2 and uart3 nodes that seem to
be broken since ages due to a copy-and-paste error.
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Linksys WRT1900AC (Mamba) is a router that has
- 2 mini-PCIe slots with Marvell 88W8864 radios
- 1 USB 3.0 port
- 1 USB 2.0/eSATAp port
- 2 Ethernet interfaces connected to a 88E6172 switch (1x WAN + 4x LAN)
- 128MB NAND flash
- 256MB RAM
gregory.clement@free-electrons.com: - add ARM to the title
- fix the reference to CONFIG_DEBUG_MVEBU_UART0_ALTERNATE
- fix the unbalanced comment for the syscfg partition
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds reset-gpios property to the eMMC slot, so the MMC driver
is able to properly reset eMMC card on system restart and thus fixes
system hang on software reboot.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Define videoports and use endpoints to describe the connection between
the encoder, bridge and the panel, instead of using phandles.
Signed-off-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Tested-by: Rahul Sharma <rahul.sharma@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Enabling SDIO IRQ signalling for the wifi MMC/SDIO slot
doubles the transmission transfer rate.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Snow board has a MMC/SDIO wifi chip that is always powered but it
needs a power sequence involving a reset (active low) and an enable
(active high) pins. Both pins are marked as active low since the MMC
simple power sequence driver asserts the pins prior to the card power
up procedure and de-asserts the pins after the card has been powered.
So the reset line will be left de-asserted and the enable pin will be
left asserted.
The chip also needs an external 32kHz reference clock to be operational
that is by the MAX77686 PMIC clock.
Add a simple MMC power sequence provider for the wifi MMC/SDIO slot.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7791 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
r8a7790 SDHI ch0/ch1 has SD_DMACR which is located in 0x324.
This patch updates register size
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the three
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add references to the transmit and receive DMA channels in the four
SDHI nodes.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and
hook it up to the D4 PM domain, so the R-Mobile System Controller
driver can keep the domain powered, until the new Coresight code
handles runtime PM.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Fixes: http://bugs.elinux.org/issues/127
the bb.org community was seeing random reboots before this change.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In commit 87517d26d8 ("ARM: dts: dra7-evm: Add extcon nodes for USB")
we enabled Extcon USB gpio to tackle the USB ID pin and get
peripheral mode to work.
But the extcon-gpio-usb driver [1] didn't make it into v4.0
and this makes the USB driver defer probe indefinitely breaking
USB Host functionality.
As a temporary fix we remove the extcon handle from the
USB controller and add it back when the extcon driver
merges in v4.1.
[1] - https://lkml.org/lkml/2015/2/2/187
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to the Documentation/devicetree/bindings/dma/dma.txt the
dma-channels and dma-requests property should not have '#'.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
we have i2c0 sleep pinctrl state but were passing
default state anyhow. Fix that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As it turns out, tps62362 is actually on I2C bus0,
not bus1. This has gone unnoticed because Linux
doesn't use (as of now) that regulator at all, it's
setup by the bootloader and left as is.
While at that, also add missing reg property for
our regulator.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Offset for smc91x must be zero otherwise smc91x linux kernel driver does not
detect smc91x ethernet hardware in qemu N900 machine.
The 0x300 offset was used to supress a warning the smsc911x
driver produces about non-standard offset as 0x300 seems to
be the EEPROM default. As only three address lines are
connected both 0 and 0x300 will work just fine with 0 being
correct. The warning about the non-standard offset can be
fixed by writing to EEPROM as that's needed in any case to
set the MAC address.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
[tony@atomide.com: updated comments, just use 0 instead of 0x0]
Signed-off-by: Tony Lindgren <tony@atomide.com>
With legacy boot i2c buses on Nokia N900 are numbered i2c1, i2c2 and i2c3.
Commit 20b80942ef ("ARM: dts: OMAP3+: Add i2c aliases") fixed the
numbering with DT boot, but introduced a regression on N900 - aliases
become i2c0, i2c1 and i2c2. Fix that by providing the correct aliases in
the board dts.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Nishanth Menon <nm@ti.com>
[tony@atomide.com: this is needed for legacy user space to work]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7800064ba5 ("ARM: dts: Add basic dm816x device tree
configuration") added basic devices for dm816x, but I was not able
to test the USB completely because of an unconfigured USB phy, and
I only tested it to make sure the Mentor chips are detected and
clocked without a phy.
After testing the USB with actual devices I noticed a few issues
that should be fixed to avoid confusion:
- The USB id pin on dm8168-evm is hardwired and can be changed
only by software. As there are two USB-A type connectors, let's
start both in host mode instead of otg.
- The Mentor core is configured in such a way on dm8168-evm that
it's not capable of multipoint at least on revision c board
that I have.
- We need ranges for the syscon to properly set up the phy as
children of the SCM syscon area.
- Let's not disable the second interface, the board specific
dts files can do that if really needed. Most boards should
just keep it enabled to ensure the device is idled properly.
Note that also a phy and several musb fixes are still needed to
make the USB to work properly in addition to this fix.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The sata_ref_clk is a reference clock to the SATA phy.
This fixes SATA malfunction across suspend/resume or when
SATA driver is used as a module.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Note that unlike on R-Mobile A1 (r8a7740), PM domain D4 can be powered
down without ill effects on s2ram behavior, just like on SH-Mobile AP4
(sh7372). Hence we can postpone adding a (minimal) device node for the
Coresight-ETM hardware block.
The System Controller is also used by the R-Mobile Reset driver, which
can now restart the system.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Private Timer and Watchdog, as found in the Cortex-A9
MPCore.
Without this, there's no clocksource available during early kernel
initialization, before cmt1 is initialized, leading to a lock-up if
CONFIG_CPU_IDLE=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the sh73a0 generic multiplatform case has the same feature set
as the kzm9g DT reference board code, we get rid of the latter.
DT reference code in the future shall make use of the sh73a0
multiplatform support code with the generic SoC machine vector.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the root of the device tree to the BSC node,
as it's connected to the Bus State Controller. This allows the system
to know the right position of the Ethernet node in the clock and PM
domain hierarchy, and manage the clock and PM domain appropriately.
Also rename the node's name from "lan9220" to "ethernet", to conform to
ePAPR generic name recomendations.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on sh73a0, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain A4S.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Build the sh73a0 KZM9G board DTB in case of Multiplatform.
The DT reference case will be removed in the future and
can be ignored for now.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Sync the two DTS for the KZM9G board. The target is the file
"sh73a0-kzm9g.dts" and it is made identical to the DT reference
case with the exception of the compatbile string. In the future
the DT reference file will go away.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
[geert: Update for recent changes to sh73a0-kzm9g-reference.dts]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7794 parts of the SDHI[012] device nodes.
Based on the orginal patch by Shinobu Uehara <shinobu.uehara.xc@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the sh7372 DTSI file for the now unsupported sh7372 SoC.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the sh7372 implementation and the shared ZBOOT MMC
and SDHI support code from the compressed ARM boot loader.
With this in place it is no longer possible to boot any
self-contained kernel for sh7372 directly from Mask ROM
via SDHI and MMCIF hardware.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove the DTS file for the no longer supported Mackerel board.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on r8a7778, to which
multiple external devices can be connected.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds pin control info for USB host and video-in devices.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Declares all r8a7778 clocks supported by the legacy clock framework,
plus tmu2.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
[horms: only included dtsi changes]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This moves everything to the legacy dts that is missing there to make it
suitable for use with multiplatform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Since ("ARM: shmobile: r8a73a4: ape6evm: Remove legacy platform"),
ape6evm is restricted to booting from DT, so chosen/stdout-path is
always used, and we can drop the "console=" parameter from
chosen/bootargs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This removes the remains of the legacy ape6evm platform.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now that the r8a73a4 generic multiplatform case has the same features as the
APE6EVM DT reference board code, we get rid of the latter. DT reference
code in the future shall make use of the r8a73a4 multiplatform support code
with the generic SoC machine vector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
[geert: Update Documentation/devicetree/bindings/arm/shmobile.txt]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently the pin function controller (which is also a GPIO controller)
is instantiated before the interrupt controllers due to the order in the
DTS. At that time, the irq domains for the interrupt controllers
referenced by its interrupts-extended property cannot be found yet:
irq: no irq domain found for /interrupt-controller@e61c0000 !
Nevertheless, the core OF probing code ignores this failure, besides a
debug message that's not normally printed:
not all legacy IRQ resources mapped for pfc
and continues initialization of the device. Then, the sh-pfc driver
cannot find any IRQ resources, and thinks no interrupts are available,
causing gpio-keys to fail later:
gpio-keys keyboard: Unable to claim irq 0; error -22
gpio-keys: probe of keyboard failed with error -22
Move the pin function controller node after the interrupt controller
nodes it references to work around the bug in the core OF probing code.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Move the Ethernet node from the ad-hoc lbsc node to the BSC node,
as its connected to the Bus State Controller. This allows the system to
know the right position of the Ethernet node in the clock and PM domain
hierarchy, and manage the clock and PM domain appropriately.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a node for the Bus State Controller (BSC) on r8a73a4, to which
multiple external devices can be connected.
The BSC is driven by the ZB clock, and located in PM domain C4.
A reference to the latter will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7790 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the ADSP clocks to the CPG and MSTP5 nodes of the R8A7791 device tree.
Based on the original patch by Konstantin Kozhevnikov
<konstantin.kozhevnikov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Henninger board dependent part of the CAN0 device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7791 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7790 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from their
peripheral clock input (clkp1) but also from the other internal clock (clkp2)
and external clock fed on CAN_CLK pin. Describe those clocks in the device
tree, along with the USB_EXTAL clock from which clkp2 is derived.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Configure the pinmux on kzm9d to use the serial connector for uart1.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With this information all GPIOs can make use of the PFC functionality.
Signed-off-by: Niklas Söderlund <niso@kth.se>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the ADV7511 HDMI encoder and its HDMI output connector
and configure the DISP pin group that drives the HDMI transmitter DE
pin.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
Fixes: 59e79895b9 ("ARM: shmobile: r8a7791: Add clocks")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
* Correct base address of SD3 div6 clk.
* Update div6 clock node labels
There appears to have been some inconsistency and confusion here as on
the r8a7790 these clocks are referred to as SD(HI)1 and SD(HI)2 while on
the r8a7791 and r8a7794 they are referred to as SD(HI)2 and SD(HI)3.
This has no run-time affect as the clock nodes are not currently used.
Fixes: 8e181633e6 ("ARM: shmobile: r8a7794: Add SDHI clocks to device tree")
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Enable the ethernet controller for the Alt board. Pin muxing entries are
currently left out as r8a7794 pin control support isn't available yet.
We thus rely on the boot loader to configure ethernet pins for now.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7794 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the seven IPMMU instances found in the r8a7791 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the six IPMMU instances found in the r8a7790 to DT with a disabled
status.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Instantiate the two system DMA controllers in the r8a7794 device tree.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Traditionally, the first 16 MiB of RAM was reserved for the RT
processor. However, this is incompatible with CONFIG_AUTO_ZRELADDR=y,
which requires that the start address of physical memory is a multiple
of 128 MiB.
As CONFIG_AUTO_ZRELADDR=y is enabled for multi-platform kernels, declare
RAM to start at 0x40000000.
While at it, reclaim the last 8 MiB of RAM, too, so the full 512 MiB is
available. Note that kzm9g_defconfig still has
CONFIG_MEMORY_START=0x41000000 and CONFIG_MEMORY_SIZE=0x1f000000, so
before the advent of DT we scribbled over the last 8 MiB, too.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Specifies clock sources and register bits.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
[geert: Drop renesas,src-shift/renesas,src-width, pad to 4 or 8 parents]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This clock drives the irqpin controller modules.
Before, it was assumed enabled by the bootloader or reset state.
By making it available to the driver, we make sure it gets enabled when
needed, and allow it to be managed by system or runtime PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the R2025D real-time clock, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the ADXL345 three-axis digital accelerometer sensor,
which is connected to i2c0.
As trivial i2c devices are matched against the first compatible entry
only, compatibility is declared with "adi,adxl34x" only for now.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The device needs an interrupt to operate properly. Specify the two
interrupts used on the board.
While at it rename the DT node to accelerometer@1d to describe the
device's function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the AK8975 magnetometer sensor, which is connected to
i2c0.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Specify the device interrupt to avoid polling for end of conversion.
While at it rename the DT node to compass@c to describe the device's
function instead of its model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
While at it rename the ak4648 node to "codec" to describe the device's
function instead of its model, and move its device-specific property
after its generic properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The sh73a0 INTC can't mask interrupts properly most likely due to a
hardware bug. Set the control-parent property to delegate masking to the
parent interrupt controller.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This adds the remaining DIV6 clocks and all possible parents for the SUB
clock.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The Device Tree description of SDHCI on Armada 388 RD board was
missing. This commit adds the node for it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The binding of the armada-380-sdhci has been extended with a new
register in order to be able to use the SDR50 and DDR50 mode. This
commit add the resource associated to this new register for the
Armada 38x.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Instead of hardcoding the values of the interrupt flags, use the
macros provided by <include/dt-bindings/interrupt-controller/irq.h>
and <include/dt-bindings/interrupt-controller/arm-gic.h> for the
Armada 38x SDHCI node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This was left out of the original firefly board definition due to the
ethernet support going completely through the network tree, making the
underlying nodes unavailable.
Now that everything is present enable the gmac on the firefly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Enable usb PHY for all usb ports on rk3288-evb.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch adds a device_node for RK3288 SoC usb phy. It also
defines the phy to be used by three usb controllers: usb_host0/1
and usb_otg.
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
A few fixes that came in too late to make it into the first set of pull
requests but would still be nice to have in -rc1. The majority of these
are trivial build fixes for bugs that I found myself using randconfig
testing, and a set of two patches from Uwe to mark DT strings as 'const'
where appropriate, to resolve inconsistent section attributes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=hrfV
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few fixes that came in too late to make it into the first set of
pull requests but would still be nice to have in -rc1.
The majority of these are trivial build fixes for bugs that I found
myself using randconfig testing, and a set of two patches from Uwe to
mark DT strings as 'const' where appropriate, to resolve inconsistent
section attributes"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: make of_device_ids const
ARM: make arrays containing machine compatible strings const
ARM: mm: Remove Kconfig symbol CACHE_PL310
ARM: rockchip: force built-in regulator support for PM
ARM: mvebu: build armada375-smp code conditionally
ARM: sti: always enable RESET_CONTROLLER
ARM: rockchip: make rockchip_suspend_init conditional
ARM: ixp4xx: fix {in,out}s{bwl} data types
ARM: prima2: do not select SMP_ON_UP
ARM: at91: fix pm declarations
ARM: davinci: multi-soc kernels require AUTO_ZRELADDR
ARM: davinci: davinci_cfg_reg cannot be init
ARM: BCM: put back ARCH_MULTI_V7 dependency for mobile
ARM: vexpress: use ARM_CPU_SUSPEND if needed
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices. Additionaly the framework core underwent a bit of surgery with
two major changes. The boundary between the clock core and clock
providers (e.g clock drivers) is now more well defined with dedicated
provider helper functions. struct clk no longer maps 1:1 with the
hardware clock but is a true per-user cookie which helps us tracker
users of hardware clocks and debug bad behavior. The second major change
is the addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the regulator
framework. Unfortunately these changes to the core created some
breakeage. We think we fixed it all up but for this reason there are
lots of last minute commits trying to undo the damage.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJU54D5AAoJEDqPOy9afJhJs6AQAK5YuUwjDchdpNZx9p7OnT1q
+poehuUwE/gYjmdACqYFyaPrI/9f43iNCfFAgKGLQqmB5ZK4sm4ktzfBEhjWINR2
iiCx9QYMQVGiKwC8KU0ddeBciglE2b/DwxB45m9TsJEjowucUeBzwLEIj5DsGxf7
teXRoOWgXdz1MkQJ4pnA09Q3qEPQgmu8prhMfka/v75/yn7nb9VWiJ6seR2GqTKY
sIKL9WbKjN4AzctggdqHnMSIqZoq6vew850bv2C1fPn7GiYFQfWW+jvMlVY40dp8
nNa2ixSQSIXVw4fCtZhTIZcIvZ8puc7WVLcl8fz3mUe3VJn1VaGs0E+Yd3GexpIV
7bwkTOIdS8gSRlsUaIPiMnUob5TUMmMqjF4KIh/AhP4dYrmVbU7Ie8ccvSxe31Ku
lK7ww6BFv3KweTnW/58856ZXDlXLC6x3KT+Fw58L23VhPToFgYOdTxn8AVtE/LKP
YR3UnY9BqFx6WHXVoNvg3Piyej7RH8fYmE9om8tyWc/Ab8Eo501SHs9l3b2J8snf
w/5STd2CYxyKf1/9JLGnBvGo754O9NvdzBttRlygB14gCCtS/SDk/ELG2Ae+/a9P
YgRk2+257h8PMD3qlp94dLidEZN4kYxP/J6oj0t1/TIkERWfZjzkg5tKn3/hEcU9
qM97ZBTplTm6FM+Dt/Vk
=zCVK
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux
Pull clock framework updates from Mike Turquette:
"The clock framework changes contain the usual driver additions,
enhancements and fixes mostly for ARM32, ARM64, MIPS and Power-based
devices.
Additionally the framework core underwent a bit of surgery with two
major changes:
- The boundary between the clock core and clock providers (e.g clock
drivers) is now more well defined with dedicated provider helper
functions. struct clk no longer maps 1:1 with the hardware clock
but is a true per-user cookie which helps us tracker users of
hardware clocks and debug bad behavior.
- The addition of rate constraints for clocks. Rate ranges are now
supported which are analogous to the voltage ranges in the
regulator framework.
Unfortunately these changes to the core created some breakeage. We
think we fixed it all up but for this reason there are lots of last
minute commits trying to undo the damage"
* tag 'clk-for-linus-3.20' of git://git.linaro.org/people/mike.turquette/linux: (113 commits)
clk: Only recalculate the rate if needed
Revert "clk: mxs: Fix invalid 32-bit access to frac registers"
clk: qoriq: Add support for the platform PLL
powerpc/corenet: Enable CLK_QORIQ
clk: Replace explicit clk assignment with __clk_hw_set_clk
clk: Add __clk_hw_set_clk helper function
clk: Don't dereference parent clock if is NULL
MIPS: Alchemy: Remove bogus args from alchemy_clk_fgcs_detr
clkdev: Always allocate a struct clk and call __clk_get() w/ CCF
clk: shmobile: div6: Avoid division by zero in .round_rate()
clk: mxs: Fix invalid 32-bit access to frac registers
clk: omap: compile legacy omap3 clocks conditionally
clkdev: Export clk_register_clkdev
clk: Add rate constraints to clocks
clk: remove clk-private.h
pci: xgene: do not use clk-private.h
arm: omap2+ remove dead clock code
clk: Make clk API return per-user struct clk instances
clk: tegra: Define PLLD_DSI and remove dsia(b)_mux
clk: tegra: Add support for the Tegra132 CAR IP block
...
Pull dmaengine updates from Vinod Koul:
"This update brings:
- the big cleanup up by Maxime for device control and slave
capabilities. This makes the API much cleaner.
- new IMG MDC driver by Andrew
- new Renesas R-Car Gen2 DMA Controller driver by Laurent along with
bunch of fixes on rcar drivers
- odd fixes and updates spread over driver"
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (130 commits)
dmaengine: pl330: add DMA_PAUSE feature
dmaengine: pl330: improve pl330_tx_status() function
dmaengine: rcar-dmac: Disable channel 0 when using IOMMU
dmaengine: rcar-dmac: Work around descriptor mode IOMMU errata
dmaengine: rcar-dmac: Allocate hardware descriptors with DMAC device
dmaengine: rcar-dmac: Fix oops due to unintialized list in error ISR
dmaengine: rcar-dmac: Fix spinlock issues in interrupt
dmaenegine: edma: fix sparse warnings
dmaengine: rcar-dmac: Fix uninitialized variable usage
dmaengine: shdmac: extend PM methods
dmaengine: shdmac: use SET_RUNTIME_PM_OPS()
dmaengine: pl330: fix bug that cause start the same descs in cyclic
dmaengine: at_xdmac: allow muliple dwidths when doing slave transfers
dmaengine: at_xdmac: simplify channel configuration stuff
dmaengine: at_xdmac: introduce save_cc field
dmaengine: at_xdmac: wait for in-progress transaction to complete after pausing a channel
ioat: fail self-test if wait_for_completion times out
dmaengine: dw: define DW_DMA_MAX_NR_MASTERS
dmaengine: dw: amend description of dma_dev field
dmatest: move src_off, dst_off, len inside loop
...
This pull request contains the following Broadcom SoCs Device Tree changes:
- Ray adds support for the Cygnus i2c Device Tree controller on Cygnus SoCs
- Fixes to the BCM63138 dtsi file for the L2 cache controller properties
* tag 'arm-soc/for-3.20/dts' of http://github.com/broadcom/stblinux:
ARM: dts: add I2C device nodes for Broadcom Cygnus
ARM: dts: BCM63xx: fix L2 cache properties
These are changes for drivers that are intimately tied to some SoC
and for some reason could not get merged through the respective
subsystem maintainer tree.
This time around, much of this is for at91, with the bulk of it being syscon
and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=T7R2
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
New and updated SoC support. Also included are some cleanups where the
platform maintainers hadn't separated cleanups from new developent in
separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might start
combining the cleanup and new-development branches more.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=szd9
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform changes from Olof Johansson:
"New and updated SoC support. Also included are some cleanups where
the platform maintainers hadn't separated cleanups from new developent
in separate branches.
Some of the larger things worth pointing out:
- A large set of changes from Alexandre Belloni and Nicolas Ferre
preparing at91 platforms for multiplatform and cleaning up quite a
bit in the process.
- Removal of CSR's "Marco" SoC platform that never made it out to the
market. We love seeing these since it means the vendor published
support before product was out, which is exactly what we want!
New platforms this release are:
- Conexant Digicolor (CX92755 SoC)
- Hisilicon HiP01 SoC
- CSR/sirf Atlas7 SoC
- ST STiH418 SoC
- Common code changes for Nvidia Tegra132 (64-bit SoC)
We're seeing more and more platforms having a harder time labelling
changes as cleanups vs new development -- which is a good sign that
we've come quite far on the cleanup effort. So over time we might
start combining the cleanup and new-development branches more"
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (124 commits)
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: digicolor: select syscon and timer
ARM: zynq: Simplify SLCR initialization
ARM: zynq: PM: Fixed simple typo.
ARM: zynq: Setup default gpio number for Xilinx Zynq
ARM: digicolor: add low level debug support
ARM: initial support for Conexant Digicolor CX92755 SoC
ARM: OMAP2+: Add dm816x hwmod support
ARM: OMAP2+: Add clock domain support for dm816x
ARM: OMAP2+: Add board-generic.c entry for ti81xx
ARM: at91: pm: remove warning to remove SOC_AT91SAM9263 usage
ARM: at91: remove unused mach/system_rev.h
ARM: at91: stop using HAVE_AT91_DBGUx
ARM: at91: fix ordering of SRAM and PM initialization
...
This is a good healthy set of various code removals. Total net delta is 8100
lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tsjK
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This is a good healthy set of various code removals. Total net delta
is 8100 lines removed.
Among the larger cleanups are:
- Removal of old Samsung S3C DMA infrastructure by Arnd
- Removal of the non-DT version of the 'lager' board by Magnus Damm
- General stale code removal on OMAP and Davinci by Rickard Strandqvist
- Removal of non-DT support on am3517 platforms by Tony Lindgren
... plus several other cleanups of various platforms across the board"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (47 commits)
ARM: sirf: drop redundant function and marco declaration
arm: omap: specify PMUs are for ARMv7 CPUs
arm: shmobile: specify PMUs are for ARMv7 CPUs
arm: iop: specify PMUs are for XScale CPUs
arm: pxa: specify PMUs are for XScale CPUs
arm: realview: specify PMU types
ARM: SAMSUNG: remove unused DMA infrastructure
ARM: OMAP3: Add back Kconfig option MACH_OMAP3517EVM for ASoC
ARM: davinci: Remove CDCE949 driver
ARM: at91: remove useless at91rm9200_set_type()
ARM: at91: remove useless at91rm9200_dt_initialize()
ARM: at91: move debug-macro.S into the common space
ARM: at91: remove useless at91_sysirq_mask_rtx
ARM: at91: remove useless config MACH_AT91SAM9_DT
ARM: at91: remove useless config MACH_AT91RM9200_DT
ARM: at91: remove unused mach/memory.h
ARM: at91: remove useless header file includes
ARM: at91: remove unneeded header file
rtc: at91/Kconfig: remove useless options
ARM: at91/Documentation: add a README for Atmel SoCs
...
Merge fifth set of updates from Andrew Morton:
- A few things which were awaiting merges from linux-next:
- rtc
- ocfs2
- misc others
- Willy's "dax" feature: direct fs access to memory (mainly NV-DIMMs)
which isn't backed by pageframes.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (37 commits)
rtc: add driver for DS1685 family of real time clocks
MAINTAINERS: add entry for Maxim PMICs on Samsung boards
lib/Kconfig: use bool instead of boolean
powerpc: drop _PAGE_FILE and pte_file()-related helpers
ocfs2: set append dio as a ro compat feature
ocfs2: wait for orphan recovery first once append O_DIRECT write crash
ocfs2: complete the rest request through buffer io
ocfs2: do not fallback to buffer I/O write if appending
ocfs2: allocate blocks in ocfs2_direct_IO_get_blocks
ocfs2: implement ocfs2_direct_IO_write
ocfs2: add orphan recovery types in ocfs2_recover_orphans
ocfs2: add functions to add and remove inode in orphan dir
ocfs2: prepare some interfaces used in append direct io
MAINTAINERS: fix spelling mistake & remove trailing WS
dax: does not work correctly with virtual aliasing caches
brd: rename XIP to DAX
ext4: add DAX functionality
dax: add dax_zero_page_range
ext2: get rid of most mentions of XIP in ext2
ext2: remove ext2_aops_xip
...
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version).
Note: isl9305 is an I2C device so the patch does not in fact currently
depend on the introduction of "isil"-based compatible string in isl9305
driver (provided by another patch) because I2C core does not check the
prefix yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Uwe Kleine-Knig <uwe@kleine-koenig.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull clocksource updates from Ingo Molnar:
"The main change in this tree is the addition of various new SoC
clocksource/clockevents drivers: Conexant Digicolor SoCs, rockchip
rk3288 board, asm9260 for MIPS and versatile AB/PB boards"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
dts: versatile: Add sysregs node
clocksource: versatile: Adapt for Versatile AB and PB boards
dt/bindings: Add binding for Versatile system registers
clocksource: Driver for Conexant Digicolor SoC timer
clocksource: devicetree: Document Conexant Digicolor timer binding
clockevents: rockchip: Add rockchip timer for rk3288
ARM: clocksource: Add asm9260_timer driver
clocksource: marco: Rename marco to atlas7
clocksource: sirf: Remove unused variable
Add I2C device nodes and its properties in bcm-cygnus.dtsi but keep
them disabled there. Individual I2C devices can be enabled in board
specific dts file when I2C slave devices are enabled in the future
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
The L2 cache properties were completely off with respect to what the
hardware is configured for. Fix the cache-size, cache-line-size and
cache-sets to reflect the L2 cache controller we have: 512KB, 16 ways
and 32 bytes per cache-line.
Fixes: 46d4bca044 ("ARM: BCM63XX: add BCM63138 minimal Device Tree")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as well.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlTgtgkACgkQMUfUDdst+ykXbACg14oFAmeYjO9RsdIHPXBvKseO
47QAn0foy91bpNQ5UFOxWS5L6Fzj2ZND
=syx2
-----END PGP SIGNATURE-----
Merge tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver patches from Greg KH:
"Here's the big tty/serial driver update for 3.20-rc1. Nothing huge
here, just lots of driver updates and some core tty layer fixes as
well. All have been in linux-next with no reported issues"
* tag 'tty-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (119 commits)
serial: 8250: Fix UART_BUG_TXEN workaround
serial: driver for ETRAX FS UART
tty: remove unused variable sprop
serial: of-serial: fetch line number from DT
serial: samsung: earlycon support depends on CONFIG_SERIAL_SAMSUNG_CONSOLE
tty/serial: serial8250_set_divisor() can be static
tty/serial: Add Spreadtrum sc9836-uart driver support
Documentation: DT: Add bindings for Spreadtrum SoC Platform
serial: samsung: remove redundant interrupt enabling
tty: Remove external interface for tty_set_termios()
serial: omap: Fix RTS handling
serial: 8250_omap: Use UPSTAT_AUTORTS for RTS handling
serial: core: Rework hw-assisted flow control support
tty/serial: 8250_early: Add support for PXA UARTs
tty/serial: of_serial: add support for PXA/MMP uarts
tty/serial: of_serial: add DT alias ID handling
serial: 8250: Prevent concurrent updates to shadow registers
serial: 8250: Use canary to restart console after suspend
serial: 8250: Refactor XR17V35X divisor calculation
serial: 8250: Refactor divisor programming
...
The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This commit adds the Device Tree
description of this interface at the SoC level.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Arnaud Ebalard <arno@natisbad.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Boris BREZILLON <boris.brezillon@free-electrons.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: Tawfik Bayouk <tawfik@marvell.com>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now that alarm support for ISL12057 chip is available w/ the specific
"isil,irq2-can-wakeup-machine" property, let's use that feature of the
driver dedicated to NETGEAR ReadyNAS 102, 104 and 2120 specific routing of
RTC Alarm IRQ#2 pin; on those devices, this pin is not connected to the
SoC but to a PMIC, which allows the device to be powered up when RTC alarm
rings.
For that to work, the chip needs to be explicitly marked as a device
wakeup source using this "isil,irq2-can-wakeup-machine" boolean property.
This makes 'wakealarm' sysfs entry available to configure the alarm.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Peter Huewe <peter.huewe@infineon.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Landley <rob@landley.net>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Uwe Kleine-König <uwe@kleine-koenig.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull ARM updates from Russell King:
- clang assembly fixes from Ard
- optimisations and cleanups for Aurora L2 cache support
- efficient L2 cache support for secure monitor API on Exynos SoCs
- debug menu cleanup from Daniel Thompson to allow better behaviour for
multiplatform kernels
- StrongARM SA11x0 conversion to irq domains, and pxa_timer
- kprobes updates for older ARM CPUs
- move probes support out of arch/arm/kernel to arch/arm/probes
- add inline asm support for the rbit (reverse bits) instruction
- provide an ARM mode secondary CPU entry point (for Qualcomm CPUs)
- remove the unused ARMv3 user access code
- add driver_override support to AMBA Primecell bus
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (55 commits)
ARM: 8256/1: driver coamba: add device binding path 'driver_override'
ARM: 8301/1: qcom: Use secondary_startup_arm()
ARM: 8302/1: Add a secondary_startup that assumes ARM mode
ARM: 8300/1: teach __asmeq that r11 == fp and r12 == ip
ARM: kprobes: Fix compilation error caused by superfluous '*'
ARM: 8297/1: cache-l2x0: optimize aurora range operations
ARM: 8296/1: cache-l2x0: clean up aurora cache handling
ARM: 8284/1: sa1100: clear RCSR_SMR on resume
ARM: 8283/1: sa1100: collie: clear PWER register on machine init
ARM: 8282/1: sa1100: use handle_domain_irq
ARM: 8281/1: sa1100: move GPIO-related IRQ code to gpio driver
ARM: 8280/1: sa1100: switch to irq_domain_add_simple()
ARM: 8279/1: sa1100: merge both GPIO irqdomains
ARM: 8278/1: sa1100: split irq handling for low GPIOs
ARM: 8291/1: replace magic number with PAGE_SHIFT macro in fixup_pv code
ARM: 8290/1: decompressor: fix a wrong comment
ARM: 8286/1: mm: Fix dma_contiguous_reserve comment
ARM: 8248/1: pm: remove outdated comment
ARM: 8274/1: Fix DEBUG_LL for multi-platform kernels (without PL01X)
ARM: 8273/1: Seperate DEBUG_UART_PHYS from DEBUG_LL on EP93XX
...
Pull input updates from Dmitry Torokhov:
"The first round of updates for the input subsystem.
A few new drivers (power button handler for AXP20x PMIC, tps65218
power button driver, sun4i keys driver, regulator haptic driver, NI
Ettus Research USRP E3x0 button, Alwinner A10/A20 PS/2 controller).
Updates to Synaptics and ALPS touchpad drivers (with more to come
later), brand new Focaltech PS/2 support, update to Cypress driver to
handle Gen5 (in addition to Gen3) devices, and number of other fixups
to various drivers as well as input core"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (54 commits)
Input: elan_i2c - fix wrong %p extension
Input: evdev - do not queue SYN_DROPPED if queue is empty
Input: gscps2 - fix MODULE_DEVICE_TABLE invocation
Input: synaptics - use dmax in input_mt_assign_slots
Input: pxa27x_keypad - remove unnecessary ARM includes
Input: ti_am335x_tsc - replace delta filtering with median filtering
ARM: dts: AM335x: Make charge delay a DT parameter for TSC
Input: ti_am335x_tsc - read charge delay from DT
Input: ti_am335x_tsc - remove udelay in interrupt handler
Input: ti_am335x_tsc - interchange touchscreen and ADC steps
Input: MT - add support for balanced slot assignment
Input: drv2667 - remove wrong and unneeded drv2667-haptics modalias
Input: drv260x - remove wrong and unneeded drv260x-haptics modalias
Input: cap11xx - remove wrong and unneeded cap11xx modalias
Input: sun4i-ts - add support for touchpanel controller on A31
Input: serio - add support for Alwinner A10/A20 PS/2 controller
Input: gtco - use sign_extend32() for sign extension
Input: elan_i2c - verify firmware signature applying it
Input: elantech - remove stale comment from Kconfig
Input: cyapa - off by one in cyapa_update_fw_store()
...
In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data
driven initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/84r
-----END PGP SIGNATURE-----
Merge tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"In this batch, you can find lots of cleanups through the whole
subsystem, as our good New Year's resolution. Lots of LOCs and
commits are about LINE6 driver that was promoted finally from staging
tree, and as usual, there've been widely spread ASoC changes.
Here some highlights:
ALSA core changes
- Embedding struct device into ALSA core structures
- sequencer core cleanups / fixes
- PCM msbits constraints cleanups / fixes
- New SNDRV_PCM_TRIGGER_DRAIN command
- PCM kerneldoc fixes, header cleanups
- PCM code cleanups using more standard codes
- Control notification ID fixes
Driver cleanups
- Cleanups of PCI PM callbacks
- Timer helper usages cleanups
- Simplification (e.g. argument reduction) of many driver codes
HD-audio
- Hotkey and LED support on HP laptops with Realtek codecs
- Dock station support on HP laptops
- Toshiba Satellite S50D fixup
- Enhanced wallclock timestamp handling for HD-audio
- Componentization to simplify the linkage between i915 and hd-audio
drivers for Intel HDMI/DP
USB-audio
- Akai MPC Element support
- Enhanced timestamp handling
ASoC
- Lots of refactoringin ASoC core, moving drivers to more data driven
initialization and rationalizing a lot of DAPM usage
- Much improved handling of CDCLK clocks on Samsung I2S controllers
- Lots of driver specific cleanups and feature improvements
- CODEC support for TI PCM514x and TLV320AIC3104 devices
- Board support for Tegra systems with Realtek RT5677
- New driver for Maxim max98357a
- More enhancements / fixes for Intel SST driver
Others
- Promotion of LINE6 driver from staging along with lots of rewrites
and cleanups
- DT support for old non-ASoC atmel driver
- oxygen cleanups, XIO2001 init, Studio Evolution SE6x support
- Emu8000 DRAM size detection fix on ISA(!!) AWE64 boards
- A few more ak411x fixes for ice1724 boards"
* tag 'sound-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (542 commits)
ALSA: line6: toneport: Use explicit type for firmware version
ALSA: line6: Use explicit type for serial number
ALSA: line6: Return EIO if read/write not successful
ALSA: line6: Return error if device not responding
ALSA: line6: Add delay before reading status
ASoC: Intel: Clean data after SST fw fetch
ALSA: hda - Add docking station support for another HP machine
ALSA: control: fix failure to return new numerical ID in 'replace' event data
ALSA: usb: update trigger timestamp on first non-zero URB submitted
ALSA: hda: read trigger_timestamp immediately after starting DMA
ALSA: pcm: allow for trigger_tstamp snapshot in .trigger
ALSA: pcm: don't override timestamp unconditionally
ALSA: off by one bug in snd_riptide_joystick_probe()
ASoC: rt5670: Set use_single_rw flag for regmap
ASoC: rt286: Add rt288 codec support
ASoC: max98357a: Fix build in !CONFIG_OF case
ASoC: Intel: fix platform_no_drv_owner.cocci warnings
ARM: dts: Switch Odroid X2/U2 to simple-audio-card
ARM: dts: Exynos4 and Odroid X2/U3 sound device nodes update
ALSA: control: fix failure to return numerical ID in 'add' event
...
Pull networking updates from David Miller:
1) More iov_iter conversion work from Al Viro.
[ The "crypto: switch af_alg_make_sg() to iov_iter" commit was
wrong, and this pull actually adds an extra commit on top of the
branch I'm pulling to fix that up, so that the pre-merge state is
ok. - Linus ]
2) Various optimizations to the ipv4 forwarding information base trie
lookup implementation. From Alexander Duyck.
3) Remove sock_iocb altogether, from CHristoph Hellwig.
4) Allow congestion control algorithm selection via routing metrics.
From Daniel Borkmann.
5) Make ipv4 uncached route list per-cpu, from Eric Dumazet.
6) Handle rfs hash collisions more gracefully, also from Eric Dumazet.
7) Add xmit_more support to r8169, e1000, and e1000e drivers. From
Florian Westphal.
8) Transparent Ethernet Bridging support for GRO, from Jesse Gross.
9) Add BPF packet actions to packet scheduler, from Jiri Pirko.
10) Add support for uniqu flow IDs to openvswitch, from Joe Stringer.
11) New NetCP ethernet driver, from Muralidharan Karicheri and Wingman
Kwok.
12) More sanely handle out-of-window dupacks, which can result in
serious ACK storms. From Neal Cardwell.
13) Various rhashtable bug fixes and enhancements, from Herbert Xu,
Patrick McHardy, and Thomas Graf.
14) Support xmit_more in be2net, from Sathya Perla.
15) Group Policy extensions for vxlan, from Thomas Graf.
16) Remove Checksum Offload support for vxlan, from Tom Herbert.
17) Like ipv4, support lockless transmit over ipv6 UDP sockets. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1494+1 commits)
crypto: fix af_alg_make_sg() conversion to iov_iter
ipv4: Namespecify TCP PMTU mechanism
i40e: Fix for stats init function call in Rx setup
tcp: don't include Fast Open option in SYN-ACK on pure SYN-data
openvswitch: Only set TUNNEL_VXLAN_OPT if VXLAN-GBP metadata is set
ipv6: Make __ipv6_select_ident static
ipv6: Fix fragment id assignment on LE arches.
bridge: Fix inability to add non-vlan fdb entry
net: Mellanox: Delete unnecessary checks before the function call "vunmap"
cxgb4: Add support in cxgb4 to get expansion rom version via ethtool
ethtool: rename reserved1 memeber in ethtool_drvinfo for expansion ROM version
net: dsa: Remove redundant phy_attach()
IB/mlx4: Reset flow support for IB kernel ULPs
IB/mlx4: Always use the correct port for mirrored multicast attachments
net/bonding: Fix potential bad memory access during bonding events
tipc: remove tipc_snprintf
tipc: nl compat add noop and remove legacy nl framework
tipc: convert legacy nl stats show to nl compat
tipc: convert legacy nl net id get to nl compat
tipc: convert legacy nl net id set to nl compat
...
Now when the CDCLK I2S output clock can be handled through the clock
API the Odroid X2/U3 can be switched to the simple-audio-card DT binding.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clock related properties are added to the Exynos4 I2S device nodes
so they can be referred to as clock providers. Missing i2s_opclk1
clock is added to the I2S0 node and clock properties are added
to the MAX98090 codec node to allow it to control/read frequency
of the MCLK clock directly.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Hopefully the final pull request for 3.19: this ended up with a
slightly higher volume than wished, but I put them all as they are
either stable or 3.19 regression fixes.
Most of commits are from ASoC, and have been stewed for a while in
linux-next. The only change in the common code is the regression
fixes for ASoC AC97 stuff wrt device registrations. The rest are
device-specific, mostly small fixes in various ASoC drivers and
ak411x on ice1724 boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=JNb4
-----END PGP SIGNATURE-----
Merge tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Hopefully the final pull request for 3.19: this ended up with a
slightly higher volume than wished, but I put them all as they are
either stable or 3.19 regression fixes.
Most of commits are from ASoC, and have been stewed for a while in
linux-next. The only change in the common code is the regression
fixes for ASoC AC97 stuff wrt device registrations. The rest are
device-specific, mostly small fixes in various ASoC drivers and ak411x
on ice1724 boards"
* tag 'sound-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ASoC: Intel: fix sst firmware path for cht-bsw-rt5672
ARM: dts: Fix I2S1, I2S2 compatible for exynos4 SoCs
ASoC: sgtl5000: add delay before first I2C access
MAINTAINERS: ASoC: add maintainer for Intel BDW/HSW ASoC driver
ASoC: atmel_ssc_dai: fix the setting for DSP mode
ASoC: sgtl5000: Use shift mask when setting codec mode
ASoC: tlv320aic3x: Fix data delay configuration
ALSA: ak411x: Fix stall in work callback
ASoC: Intel: Used lock version to update shim registers
ASoC: wm8731: init mutex in i2c init path
ASoC: atmel_ssc_dai: fix start event for I2S mode
ASoC: rt5640: Add RT5642 ACPI ID for Intel Baytrail
ASoC: wm97xx: Reset AC'97 device before registering it
ASoC: Add support for allocating AC'97 device before registering it
X11. This should make it easier to reuse these files with other
operating systems and boot loaders.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCAAGBQJUxuxOAAoJEOa/DcumaUyEShgP/3kdxUxjKFDxLuerOCbvUQ5p
raAXsnysEij0x0yrQcIGRKLRN/OyQ/mZYcGJIAo6f15OuUKs+q7zoFW47kKMCoHY
mDNp2bHC8j2LDp2QE7Ylib6xE1ttQFxRtABzLdem6yxuQHniHa+tkM7i6Kbil9Lk
v764iOu3BAlLBKK7IEtoGeywWmhJ3mQ9IX8Tp5i91G0JW5GG7gpfrxg2RyzbBRg6
75c3inm7nDpqQw6vBraJRLpPOD6TYTskWVPuEFiCoXJbOEBShgsE2q1RXEaJml71
lajF7abfWpsmqhv5MsCPXBYJvC4MnHM7mDdE3OMr7/sjAYUHqnssFafS/o7B9eHW
MpU/b8RBVzFlzs9PQ8WPcnOOomvgsKmuVTVTfzmdgnZDD75SMzNaZNDxYY9pISoZ
UYelj7iKITr8fWuUkslf/ywuhCQjzs27sqM947Izpj3n71X2+UsxnwL1JvAv4vmh
754I50Wo++RbbhKzm0HpkyzlGETeL97GdlCSBhWlU5nMFuUqzkSNPrSg7G9FbbpQ
FrzTiQReBw8xe3YOrkQqSvGBZmv/KkNxIUYlqjkaDU0ni1ghjL2jzzv9J1wFvzpa
yX+RFbYTj2t+foCROnsS/e4UBIwVjTpB5m96y2I+GiDRQO81ZAGote37TGCn3/6d
kuDhIBUHqNE1PyZ5IziG
=gJhY
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.20-3' of git://git.infradead.org/linux-mvebu into next/dt
Merge "ARM: mvebu: DT changes for v3.20 (round 2)" from Gregory CLEMENT:
Relicense all Armada dts{i} files under dual license of GPLv2+ and
X11. This should make it easier to reuse these files with other
operating systems and boot loaders.
* tag 'mvebu-dt-3.20-3' of git://git.infradead.org/linux-mvebu: (27 commits)
ARM: mvebu: armada-xp-synology-ds414: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-openblocks-ax3-4: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-netgear-rn2120: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78460: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78260: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78230: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-matrix: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-lenovo-ix4-300d: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-gp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-axpwifiap: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-38x: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-rd: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-385: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-380: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-370-xp: Relicense the device tree under GPLv2+/X11
...
Signed-off-by: Olof Johansson <olof@lixom.net>
fix various devices for gta04, and add USB nodes for am57xx
and dra7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sRWN
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dt-pt3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 3" from Tony Lindgren:
Device tree related chages for omaps to fix dm816x syscon,
fix various devices for gta04, and add USB nodes for am57xx
and dra7.
* tag 'omap-for-v3.20/dt-pt3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: Fix dm816x pinctrl and syscon so they are children of SCM
ARM: dts: omap3-gta04: Disable keypad
ARM: dts: omap3-gta04: only power DSS when necessary.
ARM: dts: omap3-gta04: add gyroscope
ARM: dts: omap3-gta04: enable power-off for wifi card.
ARM: dts: omap3-gta04: add comments about gpios
ARM: dts: omap3-gta04: Add ramp value for twl4030 audio
ARM: dts: omap3-gta04: Enable power-off using twl4030
ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
ARM: dts: omap3-gta04: Enable twl audio vibra support
ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
ARM: dts: omap3-gta04: Fix audio node malformatting
ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
Signed-off-by: Olof Johansson <olof@lixom.net>
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUy+f+AAoJEPOmecmc0R2BdFcH/i+9hgt9ElJxKbpPPVPVv81O
QzmIi3g+B4WqAoKBfzkug5l82mSZ4FAvmQK5ad8BYHsBaGl+GRjwwaqRqZkPUOzl
umXk0GneZ5sPK+S1UdA/S/v7hTwgEpXOLnGUCGUXbLt7Gqda99ume08jgCe2JbH5
Tfjoia5uRlOgdZIf3KBr4TkPR+LHog1i/DI9N3XrAsjLtj/igHpoRmFydBmv7noo
OuRuPY0afg1jKs/MextjM0W1JzQbGyv4Jp4NjVFv60+KZrMgS64vTDZamxYEK4Sv
wn0pQUZgevQhd3ewdLtqrcbo4wIGiLWBXQK0vzonmo5tCk8r+59QFKxeMiq2C7Q=
=ZVrD
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:
Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
ARM: dts: rockchip: add rk3288 watchdog clock
clk: rockchip: add id for watchdog pclk on rk3288
clk: rockchip: add clock IDs for the PVTM clocks
clk: rockchip: add clock ID for usbphy480m_src
Signed-off-by: Olof Johansson <olof@lixom.net>
- merge all the at91sam9 code and remove the empty SoC-specific files
- remove the at91_boot_soc that is now useless in a DT context
- move the sram code in PM code as it's now only used there
- some file + function name changes after this big cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUz8xZAAoJEAf03oE53VmQMXsH/20+t69ZaB7HHVkyJpqtHs4e
ilGPL+hSxofFjzfdvr1baHyUI6Jdu4pUHxBOBw8IY0PF87cbVhdn8JcD9eb5nnBD
Z/ekKwZFnKXOyfQaRC1CHad7T+u6wa2uY+4LOC92JZipglltBVBPrm9wjfPIkii7
R13AeXNi4a3DiOXhsAevbeLNeKF/X7L52RfVPttJwfih9B1YpSmetkMjE+mpk9D9
P1JGhgTJyojhU2AacaRA3ECut8gWqBBN/FcswAZd5POxcBbNkDlZwCgXTGf3JXEt
deVd8Sud/bCbzbxhHMGDvGmMluLpBCoxmy0ArDRewauDv6K4AbnO1p29Ad9Vs/U=
=ESBq
-----END PGP SIGNATURE-----
Merge tag 'at91-soc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/soc
Merge "at91: cleanup/soc for 3.20 #4" from Nicolas Ferre:
Fourth cleanup/soc batch for 3.20:
- merge all the at91sam9 code and remove the empty SoC-specific files
- remove the at91_boot_soc that is now useless in a DT context
- move the sram code in PM code as it's now only used there
- some file + function name changes after this big cleanup
* tag 'at91-soc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
I2S1, I2S2 on Exynos4 SoC series have limited functionality compared
to I2S0, "samsung,s3c6410-i2s" compatible should be used for them.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Instead of using magic number in the code the patch provides
DW_DMA_MAX_NR_MASTERS constant.
While here, restrict the reading of data width array by amount of the actual
number of AHB masters.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Pull ARM fixes from Russell King:
"A number of ARM fixes, the biggest is fixing a regression caused by
appended DT blobs exceeding 64K, causing the decompressor fixup code
to fail to patch the DT blob. Another important fix is for the ASID
allocator from Will Deacon which prevents some rare crashes seen on
some systems. Lastly, there's a build fix for v7M systems when printk
support is disabled.
The last two remaining fixes are more cosmetic - the IOMMU one
prevents an annoying harmless warning message, and we disable the
kernel strict memory permissions on non-MMU which can't support it
anyway"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8299/1: mm: ensure local active ASID is marked as allocated on rollover
ARM: 8298/1: ARM_KERNMEM_PERMS only works with MMU enabled
ARM: 8295/1: fix v7M build for !CONFIG_PRINTK
ARM: 8294/1: ATAG_DTB_COMPAT: remove the DT workspace's hardcoded 64KB size
ARM: 8288/1: dma-mapping: don't detach devices without an IOMMU during teardown
This patch add dt node for PPMU_{DMC0|DMC1|LEFTBUS|RIGHTBUS} for
exynos4412-trats2 board. Each PPMU dt node includes one event of
'PPMU Count3'.
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds PPMU dt node for Exynos3250 based Rinato and Monk
boards. The PPMU node is used to get the utilization of DMC0/DMC1/
LEFTBUS/RIGHTBUS Block.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds mipi dsi device node to exynos4415.dtsi.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds fimd device node to exynos4415.dtsi.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This is required to fix regression after introducing the PMU device
nodes required for the PMU driver modified in commit 14fc8b93d4
("ARM: EXYNOS: Add platform driver support for Exynos PMU").
This change is needed to make MIPI DSI displays and MIPI CSI-2
camera sensors working again on Exynos4 boards.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch add WM1811 audio codec, I2S interface and the sound
machine nodes to enable audio on exynos4412-trats2 board.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
In order to get exact 24MHz clock frequency value for the camera
sensor and avoid rounding errors the parent clock must be CLK_XUSBXTI,
not CLK_MOUT_MPLL_USER_T. Currently the sensor's master clock
frequency is too high and the sensor doesn't work properly.
This fixes commit 0357a4438d
("ARM: dts: Specify default clocks for Exynos4 camera devices").
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Assign proper FIMC-IS UART gate clock in the device DT node and not
use the SRC_MASK gate. This fixes regression introduced in commit
a37c82a3b3 ("clk: samsung: exynos4: Remove
SRC_MASK_ISP gates").
Without this change exynos4 fimc-is driver fails to probe with an
error log:
[ 1.842447] ERROR: could not get clock /camera/fimc-is@12000000:uart(13)
[ 1.848529] exynos4-fimc-is 12000000.fimc-is: failed to get clock: uart
[ 1.855275] exynos4-fimc-is: probe of 12000000.fimc-is failed with error -2
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add to Trats2 DTS new node for configuring the max77693 charger driver.
Only the maxim,constant-microvolt differs from default value but set all
of the optional properties anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Remove fixed regulators (duplicating what max77686 provides) and
add GPIO enable control to max77686 regulators.
This gives the system full control over those regulators. Previously
the state of such regulators was a mixture of what max77686 driver set
over I2C and what regulator-fixed set through GPIO.
Removal of 'regulator-always-on' from CAM_ISP_CORE_1.2V (buck9) allows
disabling it when it is not used. Previously this regulator was always
enabled because its enable state is a OR of:
- ENB9 GPIO (turned always on by regulator-fixed),
- BUCK9EN field in BUCK9CTRL register (off by max77686 through I2C).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add suspend to RAM configuration for max77686 regulators. Some LDOs
and bucks are disabled. This reduces energy consumption during S2R,
approximately from 17 mA to 9 mA.
Additionally remove old and not supported bindings:
- regulator-mem-off
- regulator-mem-idle
- regulator-mem-on
The max77686 driver does not parse them and they are not documented
anywere.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add node for fuel gauge present in Maxim 77693 PMIC. This allows control
over battery charging state on Trats2 board.
The fuel gauge is compatible with max17042 battery driver (Maxim
17042/17047/17050). Although datasheet rev 2.2 for MAX77693 describes
fuel gauge as Maxim 17042-like, the chip on Trats2 board identifies
itself as Maxim 17047-like.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The charge delay value is by default 0x400. But it can be set to lower
values on some boards, as long as false pen-ups are avoided. Lowering the
value increases the sampling rate (though current sampling rate is
sufficient for TSC operation). In some boards, the value has to be
increased to avoid false pen-up events. Hence, charge delay has been
made a DT parameter.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds stdout-path property to chosen nodes of Exynos4 boards
to enable use of earlycon feature without the need to hardcode port
number in kernel itself.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- several fixes and adjustments following the last cleanup batch
- removal of some unused Kconfig options
- slight PM and pm_idle rework to ease future rework
- removal of unneeded mach/system_rev.h
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxjj9AAoJEAf03oE53VmQGEAH/3nLneCOQeyuq60adx+Lxcdn
Q9sMMzrw4B6bQnJee7+PQD3/QU7fmF8qNKlMKYAlILFHGNQplASi4uAfRTykUA0j
RQHpS9n20ODVfX+yePJ/o8h2r1BkT2wUIDXxaZCj2RoPmEz1aiFDNa2pPsUfprRd
gpbh+ZU43LRowYwH9UHPV55PQ0ZwMq3ry2DOYY5Al1+bKQ8TFvAdDMUu3rGZU7A4
dMYiQCQ6Fv0EI1NY0IHSf/u/jujlPE2H0TSR38w8lYfIPzBx2tHkLSupuxKh7R1N
QYibgZXWR0PqHOXMpOHYBqJFj5c3f/aOZ/dO4RJha+S7YHNQnIFzLsm122njgKQ=
=KgUm
-----END PGP SIGNATURE-----
Merge tag 'at91-cleanup3' into at91-3.20-soc
One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is removed --
earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as others have in
previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but we
caught that in time before the merge window due to more machines being
affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc batch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=nw2v
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"One more week's worth of fixes. Worth pointing out here are:
- A patch fixing detaching of iommu registrations when a device is
removed -- earlier the ops pointer wasn't managed properly
- Another set of Renesas boards get the same GIC setup fixup as
others have in previous -rcs
- Serial port aliases fixups for sunxi. We did the same to tegra but
we caught that in time before the merge window due to more machines
being affected. Here it took longer for anyone to notice.
- A couple more DT tweaks on sunxi
- A follow-up patch for the mvebu coherency disabling in last -rc
batch"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arm: dma-mapping: Set DMA IOMMU ops in arm_iommu_attach_device()
ARM: shmobile: r8a7790: Instantiate GIC from C board code in legacy builds
ARM: shmobile: r8a73a4: Instantiate GIC from C board code in legacy builds
ARM: mvebu: don't set the PL310 in I/O coherency mode when I/O coherency is disabled
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Looks like on 3517 davinci_emac MAC address registers have a
different layout compared to dm816x and am33xx.
Let's add a function to get the 3517 MAC address.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On this board USB2 is meant to be used as peripheral only.
The ID pin for USB2 is hardwired HIGH.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
NOTE: the ports on this board cannot switch roles. They are
configured either host or peripheral by hardwiring the
respective ID pins.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On this EVM, the USB cable state has to be determined via the
ID pin tied to a GPIO line. We use the gpio-usb-extcon driver
to read the ID pin and the extcon framework to forward
the USB cable state information to the USB driver so the
controller can be configured in the right mode (host/peripheral).
Gets USB peripheral mode to work on this EVM.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently the hdmi driver is using one of the soc i2c busses for ddc probing
and while documentation always specifies i2c5 as hdmi-i2c it could very well
be any other bus as well.
Therefore this is a property of the board and should be specified there.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This enables the recently added display nodes on the firefly and evb,
letting the boards output graphic data over the hdmi port.
This includes enabling of i2c5 on the evb that is used for ddc probing and
setting the lcd-regulators to always on until the hdmi driver learns
about using them.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Use the same transfer speed on both the rk808 and act8846 variants and
remove the status=okay from the rk808 one which is already set in the
shared rk3288-evb.dtsi .
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The evaluation board using the act8846 as main pmic uses two additional
regulators to provide the cpu and gpu voltage. Add these and also add
the link to cpu supply from vdd_cpu.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9Imn
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 3rd DT updates for v3.20" from Kukjin Kim:
- add DISP1 power domain for support HDMI support on exynos5420/5422/5800
and the power domain node including FIMD1, MIXER and HDMI modules
(tested on exynos5420 Peach Pit and exynos5800 Peach Pi Chromebooks
and exynos5422 Odroid XU3 by Javier Martinez Canillas)
Note this is including a patch for adding clock IDs for the DISP1 power
domain with Mike and Sylwester's acks so that could be handled together
to avoid non-working.
* tag 'samsung-dt-3' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add DISP1 power domain for exynos5420
clk: exynos5420: Add IDs for clocks used in DISP1 power domain
Signed-off-by: Olof Johansson <olof@lixom.net>
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
Note that this is based on tags/samsung-dt
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=DGVz
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 2nd DT updates for v3.20" from Kukjin Kim:
- for all of Samsung SoCs
: use generic power domain bindings
: add 'dr_mode' property for hsotg/dwc2 devices
- exynos3250-rinato and exynos3250-monk
: add regulator-haptic
- exynos5422-odroidxu3
: reduce total RAM by 22 MiB because last 22 MiB
for secure monitor cannot be accessed by kernel
: add on-board INA231 sensors and LDO26 of PMIC
for the sensors
* tag 'samsung-dt-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: reduce total RAM by 22 MiB for exynos5422-odroidxu3
ARM: dts: add on-board INA231 sensors for exynos5422-odroidxu3
ARM: dts: Add regulator-haptic node for exynos3250-monk
ARM: dts: Add regulator-haptic node for exynos3250-rinato
ARM: dts: add 'dr_mode' property to hsotg devices for exynos boards
ARM: dts: convert to generic power domain bindings for exynos DT
Signed-off-by: Olof Johansson <olof@lixom.net>
There is currently a hardcoded limit of 64KB for the DTB to live in and
be extended with ATAG info. Some DTBs have outgrown that limit:
$ du -b arch/arm/boot/dts/omap3-n900.dtb
70212 arch/arm/boot/dts/omap3-n900.dtb
Furthermore, the actual size passed to atags_to_fdt() included the stack
size which is obviously wrong.
The initial DTB size is known, so use it to size the allocated workspace
with a 50% growth assumption and relocate the temporary stack above that.
This is also clamped to 32KB min / 1MB max for robustness against bad
DTB data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the PCI controller node for the Versatile/PB board.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
CC: Russell King <linux@arm.linux.org.uk>
The Versatile boards have the same sysregs as other ARM Ltd boards. Add
the nodes in order to enable support for 24MHz counter as sched_clock.
This is a minimal node definition as the existing sub node definition
used on VExpress has some issues raised by Linus W.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The DISP1 power domain on Exynos5420 SoC includes the FIMD1, MIXER
and HDMI modules. Add a device node for this power domain and mark
these modules as consumer of the DISP1 power domain.
When a power domain is powered on and off, the input clocks of the
devices attached to it are reparented. So a reference to the input
and parent clocks of the devices are needed to manage that.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Looks like I only got half done with moving pinctrl and syscon to
be children of the SCM. I've set up the FAPLL clocks that way already,
but did not complete the job as I copied the syscon values from
am33xx.dtsi.
To make sure the syscon mapping works, I've verfified that we can
set up davinci_emac mac address the same way as cpsw already does
with the syscon mapping. So let's add that too.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In one pinctrl node, a 'bias-disable' property is erroneously assigned a
value.
Fixes: ARM: zynq: DT: Add pinctrl information
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add the clock property for the watchdog on rk3288 socs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUyCaJAAoJEPOmecmc0R2By0oH/ioVbVZWYgTWJRlN0Cmjj+yr
fNnzm93g9N+Uk5PGOjCw70h3QSS65OLdqPF9xJwkSS1p7ORbKmOU3fzAET7x/EYK
a3Ct4NRPPiSkY12Qg+N4Q9wjz8sgUUHsLSFa5D/QJsyPu+lTVhLgWS4j4mzVCbyz
PSMn4Tx52OHzLHWKGrnEq33AIMROvarBmOgnvGe7AbutwDYqoiFiPALIAowrp/SR
WY689+3Gjtha5epUHn9vgUkNABnf0gXR1MBBJ1ZMxgForjZqeSCioHNYomneKOZC
9zyg4yuv5kNL75PY4aHLwalRfIFrqNM5S5D3gH7CTQg1/TcfUcVCBY0CAKczLxw=
=nDW6
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: second batch of dts updates for 3.20" from Heiko Stübner:
Basic display nodes for crtcs and hdmi encoder, timer node
for the broadcast timer going through the clocksource tree
and two new boards, the rk3288-based Firefly and the
PX2-based Rayeager board (the PX2 is identical to the rk3066
but made for industrial users).
* tag 'v3.20-rockchip-dts2' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add dts for ChipSPARK Rayeager PX2 board
ARM: dts: rockchip: add dts for Firefly Firefly-RK3288 boards
dt-bindings: add vendor prefix and root compatible property for Rockchip boards
ARM: dts: rockchip: Add rockchip timer node for rk3288
ARM: dts: rockchip: add rk3288 hdmi nodes
ARM: dts: rockchip: Add rk3288 vop and display-subsystem
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking fixes from David Miller:
1) Don't OOPS on socket AIO, from Christoph Hellwig.
2) Scheduled scans should be aborted upon RFKILL, from Emmanuel
Grumbach.
3) Fix sleep in atomic context in kvaser_usb, from Ahmed S Darwish.
4) Fix RCU locking across copy_to_user() in bpf code, from Alexei
Starovoitov.
5) Lots of crash, memory leak, short TX packet et al bug fixes in
sh_eth from Ben Hutchings.
6) Fix memory corruption in SCTP wrt. INIT collitions, from Daniel
Borkmann.
7) Fix return value logic for poll handlers in netxen, enic, and bnx2x.
From Eric Dumazet and Govindarajulu Varadarajan.
8) Header length calculation fix in mac80211 from Fred Chou.
9) mv643xx_eth doesn't handle highmem correctly in non-TSO code paths.
From Ezequiel Garcia.
10) udp_diag has bogus logic in it's hash chain skipping, copy same fix
tcp diag used. From Herbert Xu.
11) amd-xgbe programs wrong rx flow control register, from Thomas
Lendacky.
12) Fix race leading to use after free in ping receive path, from Subash
Abhinov Kasiviswanathan.
13) Cache redirect routes otherwise we can get a heavy backlog of rcu
jobs liberating DST_NOCACHE entries. From Hannes Frederic Sowa.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (48 commits)
net: don't OOPS on socket aio
stmmac: prevent probe drivers to crash kernel
bnx2x: fix napi poll return value for repoll
ipv6: replacing a rt6_info needs to purge possible propagated rt6_infos too
sh_eth: Fix DMA-API usage for RX buffers
sh_eth: Check for DMA mapping errors on transmit
sh_eth: Ensure DMA engines are stopped before freeing buffers
sh_eth: Remove RX overflow log messages
ping: Fix race in free in receive path
udp_diag: Fix socket skipping within chain
can: kvaser_usb: Fix state handling upon BUS_ERROR events
can: kvaser_usb: Retry the first bulk transfer on -ETIMEDOUT
can: kvaser_usb: Send correct context to URB completion
can: kvaser_usb: Do not sleep in atomic context
ipv4: try to cache dst_entries which would cause a redirect
samples: bpf: relax test_maps check
bpf: rcu lock must not be held when calling copy_to_user()
net: sctp: fix slab corruption from use after free on INIT collisions
net: mv643xx_eth: Fix highmem support in non-TSO egress path
sh_eth: Fix serialisation of interrupt disable with interrupt & NAPI handlers
...
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUxmgWAAoJEAf03oE53VmQtCoIAJtnUtvW5DqRWWsAzKxv6tPF
FLXihD9MRPyywgN5hDvNInKibqcBNxnLfk0xiFbCbfZXU4u6SK1E5iJN72mkTxhP
6rC/rdMDqMqGK7W43h4xFFpQdPrrq00t36gGvnQ+IUaOYcGAByJPYB3YwKMv/n0x
xHTPhydb2RPphEd9ZaXsbUKcaOJPG/6uChQSTp+8L0MAlh4cQADya1SapDhRefDa
PFz49N8QIjxgjWyJiWorcD8KH8hkGzLtvuvDl3UWkNZz9i3h7Vl3QaraC3HCHqwm
kJrOJ/EVw1uJKAKtYoo9xfoA8Z5HHno3vcQ4gKq4ylYDHIB3P4UhQLaGlcqkZfk=
=yOLr
-----END PGP SIGNATURE-----
Merge tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #2" from Nicolas Ferre:
Second DT batch for 3.20:
- correct some pin configuration for at91sam9x5ek
- add pioD on sama5d4 following a modification of pinctrl driver
- add more precise nand compatibility string for sama5d4
- audio modifications for wm8904 or ac97
* tag 'at91-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/dt: sam9263: Add ac97 device node
dt: atmel_ac97c: Add device tree documentation
ARM: at91: at91sam9n12ek/dt: use dt ids for wm8904
ARM: at91: sama5d3xek/dt: use dt ids for wm8904
ARM: at91: sama5d4: dts: change the nand compatible string
ARM: at91/dt: sama5d4: add pioD controller
ARM: at91/dt: disable pull-up on vbus-gpio (PB16) to reduce power consumption
Signed-off-by: Olof Johansson <olof@lixom.net>
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUxSjgAAoJEBx+YmzsjxAgfNcQAJdm22JbZ8T8elBXA5bU/V7e
35eM9r+osTM25w/kZaQKQ3RMhQNuBmM6BBTXX5BRYBRKBx+YL791repfa6LEH15W
ZVQ4+Iqsa3FrDiVnMGqOb+idjMuWKtluu6SBkZFeeCB7qN56zMFuEKgQaT/ICrmD
E5fG/Z91nGCVaHnvDEUCeWb+snDxlMD8E54QpUwLqnkQHvylujnY8DMSopZJuqzK
OABiBkHr9TZYFfsr9JIuKSMI3lFHtEf6RbcvLcyTbqXSvm6t/qR02ip1SIunVD/K
2MUyVuewh3VGZZgZTVPITHTWDfMIYU3BZc8lWSPDTXo55vMB5Q7UfdeyAWUEaWkI
cIVyHeOJ2442XDhqvkWHEFNZlfQl8i3nU+xmINVjp0KqcemoD2cjn9ZmKCnaoLkV
kB7VxF1e2GKOm7qnAB1qo5xRmyi2wLZsRecXdeSHYiiO2DZtSCa4E1vMqo5U01mX
0+8sKFEY+w+G/2dgoEXTsp08Yqsgd0fjCD6F8sxZdlskRsgBuBYS4s54xyrGr72b
Lo6WxUrc1GKEh7N3RvVqidXdYL6nUr/Pfg4n0LMwQPwWPUzXlpBeFQiHkVDl9/Mh
Bqb/GqYB5brw8KELb5blKuwzNQy6yP3K4glf2Rz3JfuPLr2y54/BaXGg66fS0ijP
Y1NkkG2AVh9lamtyHYBI
=pWBS
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner device tree changes for 3.20" from Maxime Ripard:
A lot of changes to the device tree for the 3.20 merge window, mostly with:
- More DT license convertions, only two DTS and two DTSI are still uncertain
and have not been converted yet
- Use the C-preprocessor includes in the device trees.
- Add support for the A31s SoC and improve the A80 support
- Add IR receiver, lradc, PS/2 support
- Add cpufreq support for all SoCs but the A23 and A80.
- And a lot of new boards
* tag 'sunxi-dt-for-3.20' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (64 commits)
ARM: dts: sun5i: Enable axp209 support on A13-OLinuxIno
ARM: sunxi: dts: Add A10/A20 PS2 pin muxing options
ARM: sunxi: dts: Add PS2 nodes to dtsi for A10,A20
ARM: dts: sun6i: Add resistive touchscreen controller node to dtsi
ARM: dts: sun4i: Add Hyundau A7HD board
ARM: dts: sun4i: Add Marsboard A10 board
ARM: dts: sun9i: Enable mmc2 on A80 Optimus Board
ARM: dts: sun9i: Add 8 bit mmc pinmux setting for mmc2
ARM: dts: sun9i: Enable mmc0 on A80 Optimus Board
ARM: dts: sun9i: Convert a80 optimus board dts to label referencing
ARM: dts: sun9i: Add mmc controller nodes to the A80 dtsi
ARM: dts: sun9i: Add mmc config clock nodes
ARM: dts: sunxi: Add missing mdio label
ARM: dts: sun5i: Add mk802_a10s board
ARM: dts: sun4i: Add mk802ii board
ARM: dts: sun4i: Add mk802 board
ARM: dts: sun4i: Add dts file for Chuwi V7 CW0825 tablet
ARM: dts: sun7i: Add dts file for Bananapro board
ARM: sun6i: Enable ARM arch timers
ARM: dts: sun6i: Convert hummingbird a31 dts to label references
...
Signed-off-by: Olof Johansson <olof@lixom.net>
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JLlc
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Merge "Allwinner fixes for 3.19" from Maxime Ripard:
Allwinner fixes for 3.19
A few minor fixes for the 3.19 kernel:
- The 8250 uart driver now respects the aliases, which pointed out that we
were using them wrong. Fixed them.
- The simplefb pipeline that was used on the A10 caused flickering and
tearing, and rendered it pretty much useless. Added a new simplefb node
with another pipeline that removes this issue. Note that we need to keep
the old node because u-boot 2015.01 uses it.
- Added a fix for the USB phy node on sun4i/sun5i
* tag 'sunxi-fixes-for-3.19' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: sunxi: dt: Fix aliases
ARM: dts: sun4i: Add simplefb node with de_fe0-de_be0-lcd0-hdmi pipeline
ARM: dts: sun6i: ippo-q8h-v5: Fix serial0 alias
ARM: dts: sunxi: Fix usb-phy support for sun4i/sun5i
Signed-off-by: Olof Johansson <olof@lixom.net>
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Yc7r
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung DT updates for v3.20" from Kukjin Kim:
- exynos3250
: add exynos_usbphy node and hsotg nodes
- exynos3250-rinato
: enable usb
: cleanup and use macro for gpio-keys
: add fimd and Panel devices support
- exynos3250-monk
: enable usb
: cleanup and use macro for gpio-keys
- exynos5250-snow
: add power and lid gpio-keys pinctrl
- exynos5420-peach-pit and exynos5800-peach-pi
: configure regulators for suspend
: set always on for USB webCam regulators
: add lid GPIO key device
- exynos5422
: add support new board Odroid XU3
- dt-bindings
: add exynos-chipid
* tag 'samsung-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Configure regulators for suspend on exynos Peach boards
ARM: dts: Set Peach boards USB WebCam regulators to always on
ARM: dts: Add lid GPIO key device node for Peach boards
ARM: dts: Add power and lid GPIO keys pinctrl for exynos5250-snow
Documentation: dt-bindings: add exynos-chipid binding information
ARM: dts: add Panel device support for exynos3250-rinato
ARM: dts: add fimd device support for exynos3250-rinato
ARM: dts: use macro in gpio keys for exynos3250 boards
ARM: dts: remove unnecessary gpio-key nodes for exynos3250 boards
ARM: dts: Enable USB node for exynos3250-monk
ARM: dts: Enable USB node for exynos3250-rinato
ARM: dts: Add hsotg node for exynos3250
ARM: dts: Add exynos_usbphy node for exynos3250
ARM: dts: Add dts file for Odroid XU3 board
Signed-off-by: Olof Johansson <olof@lixom.net>
The entries are separated as ARM V4/V5 and ARM V7 as some other per-SoC config
options may be removed in the near future.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Benoit Masson <yahoo@perenite.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Willy Tarreau <w@1wt.eu>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Simon Baatz <gmbnomis@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Marcin Wojtas <mw@semihalf.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
The current GPL only licensing on the device tree makes it very
impractical for other software components licensed under another
license.
In order to make it easier for them to reuse our device trees,
relicense our device trees under a GPL/X11 dual-license.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
