All currently supported boards use hsotg/dwc2 controller in device
('peripheral') mode, so add property which sets correct operation mode.
This patch fixes support in recent changes in dwc2 driver, which added
support for dual-role devices.
Suggested-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch replaces all custom samsung,power-domain dt
properties with generic power domain bindings and updates
documentation Samsung's devices referring to old binding.
Suggested-by: Kevin Hilman <khilman@kernel.org>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
[javier.martinez@collabora.co.uk: tested on the Exynos5800 Peach Pi Chromebook]
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=/bBX
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree bug fixes and documentation updates from Grant Likely:
"A few bugfixes for the new DT overlay feature, documentation updates,
spelling corrections, and changes to MAINTAINERS. Nothing earth
shattering here"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Overlays with sub-devices tests
of/platform: Handle of_populate drivers in notifier
of/overlay: Do not generate duplicate nodes
devicetree: document the "qemu" and "virtio" vendor prefixes
devicetree: document ARM bindings for QEMU's Firmware Config interface
Documentation: of: fix typo in graph bindings
dma-mapping: fix debug print to display correct dma_pfn_offset
of: replace Asahi Kasei Corp vendor prefix
ARM: dt: GIC: Spelling s/specific/specifier/, s/flaggs/flags/
dt/bindings: arm-boards: Spelling s/pointong/pointing/
MAINTAINERS: Update DT website and git repository
MAINTAINERS: drop DT regex matching on of_get_property and of_match_table
This contains a couple of preparatory patches for 64-bit support. A new
feature is implemented in the power-management controller which allows
it to switch off the SoC if it overheats.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=uibw
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.20-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/soc
Merge "ARM: tegra: Core code changes for v3.20" from Thierry Reding:
This contains a couple of preparatory patches for 64-bit support. A new
feature is implemented in the power-management controller which allows
it to switch off the SoC if it overheats.
* tag 'tegra-for-3.20-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
soc: tegra: Add thermal reset (thermtrip) support to PMC
ARM: tegra: Add PMC thermtrip programming to Jetson TK1 device tree
of: Add descriptions of thermtrip properties to Tegra PMC bindings
soc/tegra: pmc: Add Tegra132 support
soc/tegra: fuse: Add Tegra132 support
soc/tegra: fuse: Constify tegra_fuse_info structures
soc/tegra: Add Tegra132 support
clocksource: Build Tegra timer on 32-bit ARM only
soc/tegra: pmc: restrict compilation of suspend-related support to ARM
Signed-off-by: Olof Johansson <olof@lixom.net>
A couple of unit addresses fixes in device trees, addition of microphone
detection on Chromebook 13 and a vendor prefix update.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6KYW
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v3.20" from Thierry Reding:
A couple of unit addresses fixes in device trees, addition of microphone
detection on Chromebook 13 and a vendor prefix update.
* tag 'tegra-for-3.20-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Update isl29028 compatible string to use isil vendor prefix
ARM: tegra: Fix unit address for Cortex-A9 TWD timer
ARM: dts: tegra20: fix GR3D, DSI unit and reg base addresses
ARM: tegra: Enable the mic-detect gpio on Acer Chromebook 13
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUwg4gAAoJEFBXWFqHsHzO1NIH/AlXPcZZQM8sYbHrvWXmvVTM
JstCR6XjVvOqT9zdFbEzdgpFGvu1oSDer8tOk00hL1NZYzHJRmTr/wgNP6tsvQ0F
uoRj62B+WaMMcFanTbSdzh0tJtp7HZyFkJwjWRIL76bmd4VBsHXCPw4tr3oeDLzm
x62SP14eSevV8ydlZj4TA2Ej7SxV6esdPLGeylZldXKTvo8AUH9sYN/BAz7WXfYH
wfQ8owW/ql7YyCSRVdhSoeGG4H9qJA9M/CdwofsorLONkUx0nrBPRQfku5Uvf8Op
fydbEbZ0LAkqIVnHcLi8xgBDhjjS/7glHSx4tp+mxtDcIMzAzfAtjyrawheWqQE=
=ni1W
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
Merge "ARM: imx: device tree changes for 3.20" from Shawn Guo:
The i.MX device tree update for 3.20:
- Update i.MX6 operating-points setting in device tree to match the
latest i.MX6 data sheet
- Add i.MX6SX sabreauto board support
- Add imx6dl-udoo board support based off imx6q-udoo
- Update sabrelite board to include I2C and HDMI support
- Update the VPU compatible strings to also use cnm,coda<model>
- Remove the ocram clock from the VPU node, as the clock is already
provided inside the ocram node
- Add system reset controller and syscon-reboot for VF610
- Update VF610 device tree to use zero based naming for GPIO nodes,
so that the number scheme matches hardware manual
- A number of random device additions like watchdog for VF610, sahara
for i.MX53, QSPI for imx6sx-sdb board, etc.
Note: the branch imx/soc was merged into imx/dt because the SNVS device
tree node needs to refer to the new clock ID added by the imx/soc patch.
* tag 'imx-dt-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (28 commits)
ARM: dts: imx28-evk: remove duplicate property
ARM: vf610: use zero based naming for GPIO nodes
ARM: dts: imx6q: enable dma for ecspi5
ARM: dts: vfxxx: Add SNVS node
ARM: imx: clk-vf610: Add clock for SNVS
ARM: imx: clk-vf610: Add clock for UART4 and UART5
ARM: imx: drop CPUIDLE_FLAG_TIME_VALID from cpuidle-imx6sx
ARM: dts: imx6dl-udoo: Add board support based off imx6q-udoo
ARM: imx: support arm power off in cpuidle for i.mx6sx
ARM: imx: remove unnecessary setting for DSM
ARM: dts: imx6sx: add i.mx6sx sabreauto board support
ARM: dts: imx6sx-sdb: Add QSPI support
ARM: dts: imx6qdl: Remove OCRAM clock from VPU node
ARM: imx: apf51dev: add gpio-backlight support
ARM: imx: correct the hardware clock gate setting for shared nodes
ARM: imx: pllv3: add shift for frequency multiplier
ARM vf610: add compatibilty strings of supported Vybrid SoC's
ARM: i.MX53: dts: add sahara module
ARM: dts: imx6dl: correct cpufreq volt/freq table
ARM: dts: imx6q: update cpufreq volt/freq table
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Correct pwm clock assignment in i.MX25 device tree to fix the broken
pwm support on i.MX25
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUwZrwAAoJEFBXWFqHsHzOEMoH/iIU+ChvOXbJe7DfITJiwPXG
hjILxqR4sjcJAIfd3y67ydD4fg6wRf/Gfp3tij/Ydbjrl7TbWOaQveo7Uolr6Jaj
MiXXOvQDyISHNoS09UjmCf8+4VSDx+5hamkWSlJTXC365RI6PAQihduvCWCUF5/Y
GwUaZBNTOE8VMgel20BKmvGKGPwJDAw3K5jO5Lfwg2DYLDSqZEHa+kuOxgBjbRJp
2VkrNplkVQ7QAO4HrNIuyVSXXvgSS4fJQ1unbd+EgRBkh2yLUAOlHmOXxZouYTbh
uPr7rp2Q4pDruJj/C2O9t5ng2nnMQ6I1z54umJp+2h0VSsNOX2ZjLTHq7/SvyHE=
=SrqB
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Merge "ARM: imx: fixes for 3.19, 2nd round" from Shawn Guo:
The i.MX fixes for 3.19, 2nd round:
- Correct pwm clock assignment in i.MX25 device tree to fix the broken
pwm support on i.MX25
* tag 'imx-fixes-3.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx25: Fix PWM "per" clocks
Signed-off-by: Olof Johansson <olof@lixom.net>
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KUSL
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu/dt #2" from Andrew Lunn:
Second set of dt patches for mvebu for v3.20.
* tag 'mvebu-dt-3.20-2' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: make DTS comments reflect DEBUG_LL changes
ARM: mvebu: Armada 385 GP: Add regulators to the SATA port
ARM: Kirkwood: Added support for pogoplug e02 (pink/gray)
ARM: mvebu: fix compatible strings of MBus on Armada 375 and Armada 38x
dt: bindings: update mvebu-mbus DT binding with new compatible properties
Signed-off-by: Olof Johansson <olof@lixom.net>
sd-card clockspeed to 150mhz
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJUwBx+AAoJEPOmecmc0R2BchUH/28i49EtgL/9L6KYSY8AWb6L
Cz/msQL88xsy+zS9mGYRb9qi39SpOMS70XWUvVGp939llxzTMvP8/0NYmH6uCxOi
f7Wjf8vXlhGR01Y9S3cOsL4D7V9+4qSQVzQ/rIFpcR32OaIzN78UuSuqDnAb27/x
CzaAxol8zM+XxfdxLgWChVJaTPT3WyGC2pUAmzm+2dKviTWV2CoAqavuiWuyqj26
i0HJHG6dDNfgCt11ScSqwqVLgpQ+cQAQZ1xk4et/Skk/tXz1OCtctQnevFu9ClT5
MeTnAZvKuNDwmyWMo2V9q1d9DS1s9UY+yXBKRBaF65I+Rmzd94NGxcM7B/NVgCE=
=C1qi
-----END PGP SIGNATURE-----
Merge tag 'v3.20-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: soc updates for 3.20" [sic!] from Heiko Stübner:
dts part of core suspend support and limiting of rk3288
sd-card clockspeed to 150mhz
* tag 'v3.20-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add suspend settings for rk3288-evb-rk808
ARM: dts: rockchip: add RK3288 suspend support
ARM: dts: rockchip: set dw_mmc max-freq 150Mhz
Signed-off-by: Olof Johansson <olof@lixom.net>
dm816x devices and clocks. Also adds a qspi device for
dra72x-evm.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJUvpqoAAoJEBvUPslcq6Vz2uwQALoPyfwWCDUlxZbZy/yNPq0b
+l90dAo65hzrsPo9kWswj/lDfFDwTrLjxL9KcRu0gaoQp+UUgDOTuTIVe2ftqU4T
6C6MqriKlHL6vRYmm5BOrQq+Oc+xjdNSxfnCPOouOQRESJG8Jf7+5DykUkVcgh7n
PeLaRLLb8AtEg0eBzRl7DtqvCJDU9zq8WkbtEeNso/j7P2uZ3DL/jieS0nyx9n14
fcHlHmNlBCAUH80DfbpU9QkfAg2G3DAahtdFFBrct/CltdbkprS3efzBGawQpRrh
XBqWsFCnNz4nzAshFHgKsTmtX94mgzLj89VwvsVtVTnErlC7umbrUiPrj358F72Y
lZib7jl3BLiVsDWSqIw5iulkpS+ukW1iBCzlp5C87DSXE97XJr7UscbA9EQMesFl
bHcfq9cbpvMK6hujdx2QuZcSeahjvHSguIrxGtgtcf6Xj4Rx/iDGaTpalA5fxl65
VJn1FHmC74MYcpwnZSXk8KqVyX6IjlfRnc3C9Nt5GRXLx98h09l62LyIaMq2xAKv
EvNoKf9T7MKo1ayhCDkja4ObcRU8HhR4v5Z32NkumbqT2jP8TjhzRGuLynMiNV1w
M3Rv11D2wCo1e30vJjCpBI/cJOa6pdHFiWQrmmDI09wAywhZbmikxUJ0OIf5/H5r
D+eWlZQSGWvtsRlVRkwI
=vWKv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 2" from Tony Lindgren:
More changes for omap dts files mostly to add support for
dm816x devices and clocks. Also adds a qspi device for
dra72x-evm.
* tag 'omap-for-v3.20/dt-pt2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: dra72-evm: Add qspi device
ARM: dts: Add minimal support for dm8168-evm
ARM: dts: Add basic clocks for dm816x
ARM: dts: Add basic dm816x device tree configuration
Signed-off-by: Olof Johansson <olof@lixom.net>
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This adds the required information to reset the board during an overheating
situation to the Jetson TK1 device tree. The thermal reset is handled by the
PMC by sending an I2C message to the PMIC. The entries specify the I2C
message to be sent.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
PioD controller was not described in the device tree since we don't use
it. As pinctrl-at91 allows disabled gpio controllers in the device
tree, we can add it to complete the device description.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add an hdmi node, and also add hdmi endpoints to vopb and vopl
output port nodes.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Daniel Kurtz <djkurtz@chromium.org>
Tested-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add devicetree nodes for rk3288 VOP (Video Output Processors), and the
top level display-subsystem root node.
Later patches add endpoints (eDP, HDMI, LVDS, etc) that attach to the
VOPs' output ports.
Signed-off-by: Daniel Kurtz <djkurtz@chromium.org>
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Stephane Marchesin <marcheu@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
am437x-idk and update am437x-sk boards. Also enabling new
devices for multiple boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=LFft
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.20/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20" from Tony Lindgren:
Device tree changes for omaps. Mostly to add support for new
am437x-idk and update am437x-sk boards. Also enabling new
devices for multiple boards.
* tag 'omap-for-v3.20/dt-pt1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (21 commits)
ARM: dts: omap3-gta04: Add handling for tv output
ARM: dts: cm-t3x: add NAND support
ARM: dts: am57xx-beagle-x15: Add GPIO controlled fan node
ARM: dts: am437x-idk: add gpio-based power key
ARM: dts: N950/N9: add twl_power
ARM: dts: am437x-sk: add power button binding
ARM: dts: add support for AM437x IDK
ARM: dts: am437x-gp-evm: add VPFE device tree data
ARM: dts: am437x-sk-evm: add VPFE device tree data
ARM: dts: am43x-epos-evm: add VPFE device tree data
ARM: dts: am4372: add VPFE DT node entries
ARM: dts: DRA7X: drop id property in pcie_phy
ARM: dts: omap3-n900: cleanup english
ARM: dts: am57xx-beagle-x15: Add dual ethernet
ARM: dts: am437x-sk: remove DSS pulls
ARM: dts: am437x-sk: remove internal i2c pullups
ARM: dts: am437x-sk: add explicit pinmux for both USB instances
ARM: dts: am437x-sk: remove ethernet pulls
ARM: dts: am437x-sk: add explicit MMC0 pinmux
ARM: dts: am437x-sk: remove internal pulls from QSPI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
The Kconfig symbol DEBUG_MVEBU_UART_ALTERNATE was renamed to
DEBUG_MVEBU_UART0_ALTERNATE. And the symbol DEBUG_MVEBU_UART1_ALTERNATE
was added to allow UART1 as a DEBUG_LL target. Make the comment at the
top of this DTS reflect those changes.
Since we're touching this DTS add comments to show which blocks describe
UART0 and UART1.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The pogoplug differs from the SheevaPlug only by a
few details, but especially in the led assignments.
This patch was tested under Gentoo Linux and is
based on dts files from Arch Linux ARM and OpenWrt.
Suggested-by: Felix Kaechele <heffer@fedoraproject.org>
Suggested-by: Oleg Rakhmanov <moonman.ca@gmail.com>
Signed-off-by: Christoph Junghans <ottxor@gentoo.org>
[Andrew Lunn <andrew@lunn.ch>: Fixed subject line]
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Add dts file for Hisilicon hip01 ca9x2 board
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
[olof: Folded in smp enable-method from a different patch]
Signed-off-by: Olof Johansson <olof@lixom.net>
This comment does not correspond to the actual code.
When zImage is loaded at a lower *OR* higher address of
the destination of Image, it won't overwrite itself.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 Optimus Board has a 16GB eMMC connected to mmc2, with 8 bit
wide data bus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc2 is available on port C. Add a pinmux setting for 8 bit wide eMMC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the micro-sd slot on the A80 Optimus Board, which is connected to
mmc0. This adds the card-detect gpio and enables mmc0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The preferred method of referencing nodes from the dtsi is to use
labels, instead of copying the complete tree.
This patch converts sun9i-a80-optimus.dts to use label references.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A80 has 4 mmc controllers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the device tree nodes for the mmc config clock nodes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch add missing mdio label for sun[457]i.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Changed the compatible and node names labels]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A31 has non-initialized architected timers, without CNTFRQ or CNTVOFF set
by the Allwinner's bootloader.
Use the new DT property for such case, and enable the arch timers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Using label references is preferred when override settings from the
included dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
mmc0 is only available on port F, and is always used with a 4 bit wide
bus for the onboard micro-sd slot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use the label to reference the pin controller node, so that we can use
sunxi-common-regulators with sunxi families that don't share the same
address space mappings, such as sun9i.
This patch is mostly space changes due to the reduction of node parents.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
of_clk_get_parent_name() uses the clock-indices property to resolve
clock phandle arguments in case that the argument index does not
match the clock-output-names sequence.
This is the case on sunxi, where we use the actual bit index as the
argument to the phandle. Add the clock-indices property so that
of_clk_get_parent_name() resolves the names correctly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The mmc module clocks are A80 specific module 0 (storage) type clocks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Olliver Schinagl <oliver@schinagl.nl>
The current GPL only licensing on the DTSI makes it very impractical for other
software components licensed under another license.
In order to make it easier for them to reuse our device trees, relicense our
device trees under a GPL/X11 dual-license.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Alexander Bersenev <bay@hackerdom.ru>
Acked-by: Carlo Caione <carlo@caione.org>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Roman Byshko <rbyshko@gmail.com>
The Ippo Q8H v1.2 is almost identical to the v5, still it needs a separate
dtb file since some gpio-s surrounding the wlan/bluetooth are different,
it uses different camera sensors, and different DRAM timings.
Note that atm neither the wlan/bluetooth nor the camera are supported, so
atm their is no difference between the dts files, but because of the different
DRAM timings there are already separate u-boot configs for the 2 different
versions, and the 1.2 config refers to sun8i-a23-ippo-q8h-v1.2.dtb to be
future proof, so we need to provide a sun8i-a23-ippo-q8h-v1.2.dtb file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The a23-ippo-q8h tablets have volume up/down buttons using the lradc. This
has been tested on both a v5 and a v1.2 tablet.
Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The A23 has the same lradc controller as previous Allwinner SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
LDO3 powers the USB WiFi module. This patch also references it
from the usb-phy node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the regulator nodes for the axp209 by including
the axp209 dtsi. As the inputs of these regulators are from the
axp209's PS output, which is basically just a mux over the 2
inputs, it is considered to be unregulated. Thus we do not provide
input supply properties for them.
The regulator names and constraints are based on the board
schematics and the SoC datasheet.
DCDC2 is used as the cpu power supply. This patch also references
it from the cpu node.
Also get rid of axp209 properties already set in axp209.dtsi.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The core temperature sensor now supports thermal zones. Add a thermal
zone mapping for the cpus with passive cooling (cpufreq throttling).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP209 PMIC is used with some Allwinner SoCs. This patch adds
a dtsi file listing all the regulator nodes. The regulators are
initialized based on their device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pcDuino board has LEDs connected to PH15/PH16, and back/home/menu
buttons to PH17/18/19 respectively. Enable these via gpio-leds and
gpio-keys. This is shared across the v1 and v2 versions of the board.
Tested on a v2 and verified against the schematics of a v1.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added some newlines between the button nodes]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add simplefb nodes for "[de_fe0-]de_be0-lcd0" and "[de_fe0-]de_be0-lcd0-tve0"
display pipelines for when u-boot has set up a pipeline to drive a LCD panel /
VGA output rather then the HDMI output.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A10 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A13 FEX files in the
sunxi-boards repository. All FEX files have the same settings.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The cpu core is clocked from the "cpu" clock. Add a reference to it
in the first cpu node. Also add "cpu0" label to the node.
The operating points were taken from the A20 FEX files in the
sunxi-boards repository. Not all boards have the same settings. The
settings in this patch are the most generic ones.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the resistive touchpanel driver supports thermal sensors,
add the "#thermal-sensor-cells" property as required by the thermal
framework.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The NMI IRQ controller uses the standard flags definition for the IRQ level and
edges.
Use the common header to use defines instead of opaque numbers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The GIC requires some extra opaque arguments to set the IRQ type and flags.
Convert the DTs to using the common defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The pinctrl nodes require some extra opaque arguments for the pull up and drive
strength values.
Introduce a new header file and convert the device trees to replace these
opaque numbers by defines.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The DMA engine for the A10/A20 and derivatives require an opaque extra
argument.
Add a dt-bindings header, and convert the device trees to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Replace the various raw GPIO flags by their definition in the common
dt-bindings header.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CSQ CS908 is an A31s based top-set box, with 1G RAM, 8G NAND,
rtl8188etv usb wifi, 2 USB A receptacles (1 connected through the OTG
controller), ethernet, 3.5 mm jack with a/v out and hdmi out.
Note it has no sdcard slot and therefore can only be fel booted.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a dtsi file for A31s based boards.
Since the A31s is the same die as the A31 in a different package, this dtsi
simply includes sun6i-a31.dtsi and then overrides the pinctrl compatible to
reflect the different package, everything else is identical.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Mele M9 has an ir receiver, enable it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node for the ir receiver found on the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Added a node label]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add an ir_clk sub-node to the prcm node.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Only SPI0 is enabled, as the schematic denotes it as the only SPI bus,
while other pins are reserved for different peripherals.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These are based on the available SPI configurations of Cubieboard,
Olimex LIME, and PcDuino. There is no pin group for SPI3, as all the
boards seem to use those pins for EMAC.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Hummingbird A31 board, the RTL8211E ethernet phy has its reset
line connect to a gpio pin, instead of floating like on other boards.
Add the stmmac properties for describing the reset gpio.
The reset delays were taken from the RTL8211E datasheet.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pinmux settings for the ir receive pin of the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. This can be avoided by letting the display frontend engine
do the dma from memory, and then letting it feed the data directly into
the backend unmodified, as the frontend does have deep enough fifo-s.
Note since u-boot-v2015.01 has been released using the de_be0-lcd0-hdmi
pipeline on sun4i, we need to keep that one around too (unfortunately).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It was accidentally left (& copied & pasted all around) from our
experiments with gpio-keys-polled.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Luxul XWC-1000 is a controller device based on BCM4708 SoC. The only
unusual thing in its DTS file is "ubi" partition on NAND flash.
Signed-off-by: Dan Haab <dhaab@luxul.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
These add device tree entry for qspi device on dra72-evm.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Seems to be a left-over from an automatic merge.
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Vybrid, all peripherals are numbered starting with zero,
including the GPIO and PORT module. However, the labels of the
corresponding device tree nodes start with one, which is confusing.
Fix that by renaming the labels of the gpio nodes in the device
tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently PWM functionality is broken on mx25 due to the wrong assignment of the
PWM "per" clock.
According to Documentation/devicetree/bindings/clock/imx25-clock.txt:
pwm_ipg_per 52
,so update the pwm "per" to use 'pwm_ipg_per' instead of 'per10' clock.
With this change PWM can work fine on mx25.
Cc: <stable@vger.kernel.org>
Reported-by: Carlos Soto <csotoalonso@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=VWG8
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Second Round of Renesas ARM Based SoC DT Cleanups for v3.20" from Simon
Horman:
Second Round of Renesas ARM Based SoC DT Cleanups for v3.20
* Tidy up #sound-dai-cells settings
* Drop "renesas,rcar_sound" compatible value
* tag 'renesas-dt-cleanups2-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7791: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7790: tidyup #sound-dai-cells settings
ARM: shmobile: r8a7791 dtsi: Drop "renesas,rcar_sound" compatible value
ARM: shmobile: r8a7790 dtsi: Drop "renesas,rcar_sound" compatible value
Signed-off-by: Olof Johansson <olof@lixom.net>
The file is roughly sorted alphabetically (with some exceptions where
old options have been split in two), so alphascale should go at the
top instead of at the bottom.
Also linewrap like other entries have been lately.
Signed-off-by: Olof Johansson <olof@lixom.net>
for now it is wary basic SoC description with most important IPs needed
to make this device work
Signed-off-by: Oleksij Rempel <linux@rempel-privat.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lpO3
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "Urgent omap4 legacy interrupt regression fix for v3.19-rc series" from
Tony Lindgren:
A rather urgent pull request to fix omap4 legacy interrupts.
The legacy interrupts on omap4 got broken when gic got changed to
use irq_domain_add_linear() instead of the irq_domain_add_legacy(). We
still have the hardcoded legacy IRQ numbers in use in several places,
most notably the in the legacy DMA. It took a while to figure out
what the problem was and how it should be fixed for the -rc series.
Also include is a regression fix for the dra7 dwc3 suspend.
* tag 'omap-for-v3.19/gic-regression-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Work around hardcoded interrupts
arm: boot: dts: dra7: enable dwc3 suspend PHY quirk
Signed-off-by: Olof Johansson <olof@lixom.net>
The commit (3d125f9c91) cause i.MX6SX sdb enet cannot work. The cause is
the commit add mdio node with un-correct phy address.
The patch just correct i.MX6sx sdb board enet phy address.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows booting the device with basic functionality.
Note that at least on my revision c board the DDR3 does
not seem to work properly and only some of the memory
can be reliably used.
Also, the mainline u-boot does not seem to properly
initialize the ethernet, so I've been using the old TI
u-boot at:
http://arago-project.org/git/projects/?p=u-boot-omap3.git;a=summary
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clocks on dm816x are a bit different from the other omap
variants. The clocks are sourced from a FAPLL (Flying Adder PLL)
unlike on other omaps. Other than that, it's a similar setup
to am33xx with extra muxes and dividers that can be defined
as existing component clocks.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Similar to other omap variants, let's add dm816x support.
Note that this is based on generated data from the
TI81XX-LINUX-PSP-04.04.00.02 patches published at:
http://downloads.ti.com/dsps/dsps_public_sw/psp/LinuxPSP/TI81XX_04_04/04_04_00_02/index_FDS.html
I've verified the basic functionality, but have not been
able to test all the devices on dm8168-evm.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJUt+9WAAoJEAf03oE53VmQrlQH/2gLux3w9NMBm6GKDAJe3ZbY
JSiT9JIpcDmvVPXheeXQc0gZFGbfg8kcbx6mopPR/n6gAeP0npRApmQxS04M9M6b
HyAyj26s1h79WZOki7hhsIw6bhMCNDb7ODoDOw4F6U1/WWLh+uZY3fg+HO2CFBS8
wyDWKQQWAe0LvbaB44iw5cGsZ2+8/1rb5R7w7AqITjLTOGLvJZn50TYlY6hRrb+7
qfD0gqaRzX6axdtsGVNzkuYUuLQ3rE9IhgauhHlge9QT1Lkl4wfONnGiOFeIc+n0
tcHLb3BYBqOKDbOop+3ED3bqxcmobUIQIlEutvg5lnFkWeVYnXgkIFxHPpEK4K0=
=RH2X
-----END PGP SIGNATURE-----
Merge tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/dt
Merge "at91: dt for 3.20 #1" from Nicolas Ferre:
First batch of DT changes for 3.20:
- little typo and a LED declared
- addition of the Special Function Registers (SFR) + its binding
- RTC & SRAM nodes
- the at91sam9xe has its own .dtsi now. Not combined with at91sam9260 anymore
- addition of the Image Sensor Interface (ISI) DT part and supported sensors
* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: dts: sama5d3: add ov2640 camera sensor support
ARM: at91: dts: sama5d3: change name of pinctrl of ISI_MCK
ARM: at91: dts: sama5d3: change name of pinctrl_isi_{power,reset}
ARM: at91: dts: sama5d3: move the isi mck pin to mb
ARM: at91: dts: sama5d3: add missing pins of isi
ARM: at91: dts: sama5d3: split isi pinctrl
ARM: at91: dts: sama5d3: add isi clock
ARM: at91/dt: ethernut5: use at91sam9xe.dtsi
ARM: at91/dt: Add a dtsi for at91sam9xe
ARM: at91/dt: add SRAM nodes
ARM: at91/dt: at91rm9200ek: enable RTC
ARM: at91/dt: rm9200: add RTC node
ARM: at91/dt: at91sam9n12: Add RTC node
ARM: at91: sama5d4: Add SFR
ARM: at91: sama5d3: Add SFR
ARM: at91: Add Special Function Registers binding documentation
ARM: at91/dt: sam9263: Fix typo: ac91_clk -> ac97_clk
ARM: at91/dt: sama5d3: enable D2 as the heartbeat LED
Signed-off-by: Olof Johansson <olof@lixom.net>
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
so we drop Marco dts stuff, and add dts stuff for Atlas7.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wbyB
-----END PGP SIGNATURE-----
Merge tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/dt
Merge "CSR atlas7 init dts for 3.20" from Barry Song:
Drop Marco and add init dts stuff for Atlas7
CSR Marco SoC has never shipped to customers that could be interested
in mainline support. and new Atlas7 is a replacement SoC that is in
development.
So we drop Marco dts stuff, and add dts stuff for Atlas7.
* tag 'atlas7-init-dts-for-3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: dts: add init dts file for CSR atlas7 SoC
ARM: dts: drop MARCO platform DT stuff
Signed-off-by: Olof Johansson <olof@lixom.net>
The interrupt is 16, not 32 (which it would be if we include PPIs
in the count of interrupts).
Cc: Andy Gross <agross@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Andy Gross <agross@codeaurora.org>
Tested-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This changes muxes in gpio26 pin to function as gpio and adds support
for sd card detect for apq8064 based IFC6410 board.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various bugs
around clocks, reg ranges, etc. There's also a few defconfig updates
(which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but the nothing
in here seems particularly risky.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lJPi
-----END PGP SIGNATURE-----
Merge tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on our fixes branch for a while, so this batch is
unfortunately on the large side.
A lot of these are tweaks and fixes to device trees, fixing various
bugs around clocks, reg ranges, etc. There's also a few defconfig
updates (which are on the late side, no more of those).
All in all the diffstat is bigger than ideal at this time, but nothing
in here seems particularly risky"
* tag 'armsoc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (31 commits)
reset: sunxi: fix spinlock initialization
ARM: dts: disable CCI on exynos5420 based arndale-octa
drivers: bus: check cci device tree node status
ARM: rockchip: disable jtag/sdmmc autoswitching on rk3288
ARM: nomadik: fix up leftover device tree pins
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
ARM: exynos_defconfig: Enable LM90 driver
ARM: exynos_defconfig: Enable options for display panel support
arm: dts: Use pmu_system_controller phandle for dp phy
ARM: shmobile: sh73a0 legacy: Set .control_parent for all irqpin instances
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
...
The arndale-octa board was giving "imprecise external aborts" during
boot-up with MCPM enabled. CCI enablement of the boot cluster was found
to be the cause of these aborts (possibly because the secure f/w was not
allowing it). Hence, disable CCI for the arndale-octa board.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Tyler Baker <tyler.baker@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "at91: fixes for 3.19 #1 (ter)" from Nicolas Ferre:
First fixes batch for AT91 on 3.19:
- fix some DT entries
- correct clock entry for the at91sam9263 LCD
- add a phy_fixup for Eth1 on sama5d4
* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: berlin: Fixes for v3.19 (round 1)" from Sebastian Hesselbarth:
Marvell Berlin fixes for v3.19 round 1:
- SDHCI DT fixes for BG2Q and BG2Q reference board
- BG2Q SM GPIO DT node relocation
* tag 'berlin-fixes-for-3.19-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: correct BG2Q's SM GPIO location.
ARM: dts: berlin: add broken-cd and set bus width for eMMC in Marvell DMP DT
ARM: dts: berlin: fix io clk and add missing core clk for BG2Q sdhci2 host
Signed-off-by: Olof Johansson <olof@lixom.net>
We altered the device tree bindings for the Nomadik family of
pin controllers to be standard, this file was merged out-of-order
so we missed fixing this. Fix it up.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "omap fixes against v3.19-rc1" from Tony Lindgren:
Fixes for omaps mostly to deal with dra7 timer issues
and hypervisor mode. The other fixes are minor fixes for
various boards. The summary of the fixes is:
- Fix real-time counter rate typos for some frequencies
- Fix counter frequency drift for am572x
- Fix booting of secondary CPU in HYP mode
- Fix n900 board name for legacy user space
- Fix cpufreq in omap2plus_defconfig after Kconfig change
- Fix dra7 qspi partitions
And also, let's re-enable smc91x on some n900 boards that
we have sitting in a few test boot systems after the boot
loader dependencies got fixed.
* tag 'omap-for-v3.19/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Revert disabling of smc91x for n900
ARM: dts: dra7-evm: fix qspi device tree partition size
ARM: omap2plus_defconfig: use CONFIG_CPUFREQ_DT
ARM: OMAP2+: Fix n900 board name for legacy user space
ARM: omap5/dra7xx: Enable booting secondary CPU in HYP mode
ARM: dra7xx: Fix counter frequency drift for AM572x errata i856
ARM: omap5/dra7xx: Fix frequency typos
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: imx: fixes for 3.19" from Shawn Guo:
The i.MX fixes for 3.19:
- One fix for incorrect i.MX25 SPI1 clock assignment in device tree,
which causes system hang when accessing SPI1.
- Correct i.MX6SX QSPI parent clock configuration to fix a kernel Oops.
- Fix ULPI PHY reset modelling on imx51-babbage board to remove the
dependency on bootloader for USB3317 ULPI PHY reset.
- Correct video divider setting on i.MX6Q rev T0 1.0 to fix the issue
that HDMI is not working at high resolution on T0 1.0.
- One incremental fix for CODA960 VPU enabling in device tree to
correct interrupt order.
- LS1021A SCFG block works in BE mode, add device tree property
big-endian to make it right.
* tag 'imx-fixes-3.19' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx51-babbage: Fix ULPI PHY reset modelling
ARM: imx6sx: Set PLL2 as parent of QSPI clocks
ARM: dts: imx25: Fix the SPI1 clocks
ARM: clk-imx6q: fix video divider for rev T0 1.0
ARM: dts: imx6qdl: Fix CODA960 interrupt order
ARM: ls1021a: dtsi: add 'big-endian' property for scfg node
Signed-off-by: Olof Johansson <olof@lixom.net>
Merge "ARM: rockchip: dts fix for 3.19" from Heiko Stübner:
Increase drive-strength to sdmmc pins on rk3288-evb to fix
an issue with the fixed highspeed card detection.
* tag 'v3.19-rockchip-dtsfixes1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: bump sd card pin drive strength up on rk3288-evb
Signed-off-by: Olof Johansson <olof@lixom.net>
There is an external resistor divider on PB16, acting like a pull-down,
the pull-up increase power consumption and prevent the vbus detect pin
to reach Vss voltage, ~1.5V mesured on my board, it might not even work
if the pull-up is stronger than usual.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds device tree nodes for L2 cache controller present on
Exynos4 SoCs.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MiPHY28lp is a Generic PHY which can serve various SATA, PCIe or
USB3 devices. The two first ports can be use for either; both SATA, both
PCIe or one of each in any configuration.
The Third port is only for USB3.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
B2199 HDK is the reference board for STiH418 SoC.
It has the following characteristics:
- 3GB DDR3
- 8GB eMMC / SD-Card slot
- 32MB NOR Flash
- 1 x Gbit Ethernet
- 1 x USB3.0 port
- 2 x USB2.0 ports
- 1 x Sata or Mini-PCIe port
- 1 x WiFi 802.11ac (Quantenna)
- 1 x HDMI out
- 1 x HDMI in
- 1 x SPDIF
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
The STiH418 is advanced UHD 60fps AVC processor with 3D graphic acceleration and
quad-core ARM Cortex A9 CPU.
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the DRM/KMS dt nodes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the DRM/KMS dt nodes.
This node can't be in stih407-family.dtsi file because in the future we
will integrate a new stih418-b2199 board. It's a stih407 family board
with different drm/kms dt nodes.
That is why i created the stih407.dtsi file.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Whenever Suspend PHY bit is set on DRA7x devices,
USB will not work due to Set EP Configuration command
always failing.
This was only found after a recent commit 2164a47 (usb:
dwc3: set SUSPHY bit for all cores, which will be merged
for v3.19) added a missing *required* step to dwc3
initialization. Synopsys Databook requires that we enable
Suspend PHY bit after initialization but that, unfortunately,
breaks DRA7x.
Note that the same regression was already patched for AM437x.
Reported-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to v4l2 dt document, we add:
a camera host: ISI port.
a i2c camera sensor: ov2640 port.
to sama5d3xmb.dtsi.
The ov2640 node defines the pinctrls, clocks and refer to isi port.
The ISI node also has a reference to the ov2640 port.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_pck_as_mck is pck1, and
used to provide MCK for camera sensor.
We change its name to: pinctrl_pck1_as_isi_mck.
As we want camera sensor instead of ISI to configure the pck1 (ISI_MCK) pin.
So we remove this pinctrl from ISI DT node. It will be added in sensor's
DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
For sama5d3xmb board, the pins: pinctrl_isi_{power,reset} is used to
power-down or reset camera sensor.
So we should let camera sensor instead of ISI to configure the pins.
This patch will change pinctrl name from pinctrl_isi_{power,reset} to
pinctrl_sensor_{power,reset}. And remove these two pinctrl from ISI's
DT node. We will add these two pinctrl to sensor's DT node.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The mck is decided by the board design, move it to mb related
dtsi file.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The ISI has 12 data lines, add the missing two data lines.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
As the ISI has 12 data lines, however we only use 8 data lines with
sensor module. So, split the data line into two groups which make
it can be choosed depends on the hardware design.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The ethernut5 is actually based on an at91sam9xe, use the correct dts include.
Cc: Martin Reimann <martin.reimann@egnite.de>
Cc: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
at91sam9xe is slightly different from at91sam9260, in particular it has a
different SRAM size and location.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add nodes for the SRAM available on atmel SoCs
For the at91sam9260 and the at91sam9g20, address mirroring is used to create a
single contiguous SRAM range instead of declaring two separate banks.
Also remove leftover TODOs in the sam9g45 file
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: correct at91sam9rl sram size => 0x10000]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Enable the RTC on the at91rm9200ek.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add a node for the RTC available on at91rm9200.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Add node for the RTC available on the at91sam9n12.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The sama4d4 has Special Function Registers that allow to manage DDR, OHCI, EBI
and AIC interrupt redirection.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The sama5d3 has Special Function Registers that allow to manage OHCI, EBI and
the UTMI clock.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
[nicolas.ferre@atmel.com: reg size: 0x60]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This D2 led is available for all sama5d3x-ek board. So make it a
heartbeat LED.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Conflicts:
drivers/net/xen-netfront.c
Minor overlapping changes in xen-netfront.c, mostly to do
with some buffer management changes alongside the split
of stats into TX and RX.
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add Armada 388 General Purpose Development Board support
- Add Device Tree description of the Armada 388 SoC
- Document the Device Tree binding for the Armada 388 SoC
- a38x: Add missing labels
- a38x: Add more pinctrl functions
- Add Armada 385 Access Point Development Board support
- Add a number of pinctrl functions
- A38x: Remove redundant pinctrl informations
- a38x: Fix node names
- Add support for Seagate BlackArmor NAS220
- kirkwood: enable phy driver for SATA controller on 88f6192
- gpio_poweroff support for Iomega ix2-200
- Use all remaining MTD space foor rootfs of Iomega ix2-200
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=uzJs
-----END PGP SIGNATURE-----
Merge tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu into next/dt
Merge "mvebu: dt for v3.20" from Andrew Lunn:
mvebu dt changes for v3.20 (part #1)
- Add Armada 388 General Purpose Development Board support
- Add Device Tree description of the Armada 388 SoC
- Document the Device Tree binding for the Armada 388 SoC
- a38x: Add missing labels
- a38x: Add more pinctrl functions
- Add Armada 385 Access Point Development Board support
- Add a number of pinctrl functions
- A38x: Remove redundant pinctrl informations
- a38x: Fix node names
- Add support for Seagate BlackArmor NAS220
- kirkwood: enable phy driver for SATA controller on 88f6192
- gpio_poweroff support for Iomega ix2-200
- Use all remaining MTD space foor rootfs of Iomega ix2-200
* tag 'mvebu-dt-3.20' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Add Armada 388 General Purpose Development Board support
ARM: mvebu: Add Device Tree description of the Armada 388 SoC
ARM: mvebu: Document the Device Tree binding for the Armada 388 SoC
ARM: mvebu: a38x: Add missing labels
ARM: mvebu: a38x: Add more pinctrl functions
ARM: mvebu: Add Armada 385 Access Point Development Board support
ARM: mvebu: Add a number of pinctrl functions
ARM: mvebu: A38x: Remove redundant pinctrl informations
ARM: mvebu: a38x: Fix node names
Kirkwood: add support for Seagate BlackArmor NAS220
ARM: dts: kirkwood: enable phy driver for SATA controller on 88f6192
ARM: dts: add gpio_poweroff support for Iomega ix2-200
ARM: dts: use all remaining MTD space foor rootfs of Iomega ix2-200
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device nodes for the two SDRAM Bus State Controllers.
The SBSCs are located in the A4BC0 resp. A4BC1 PM domains, which must
not be powered down, else the system will crash.
References to the A4BC0 and A4BC1 PM domains will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the DDR3 Bus State Controller (DBSC3).
The DBSC3 is located in the A4S PM domain, which must not be powered
down, else the system will crash.
This has no visible effect for now, as A4S was never turned off anyway
because its child PM domain A3SM contains the CPU core.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add device nodes for the two DDR Bus State Controllers (DBSC).
The DBSCs are located in the A3BC PM domain, which must not be powered
down, else the system will crash.
A reference to the A3BC PM domain will be added later.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The regulator core now has support to choose if a regulator
has to be enabled or disabled during system suspend and also
supports changing the regulator operating mode during runtime
and when the system enters into sleep mode.
To lower power during suspend, configure the regulators state
using the same configuration found in the ChromeOS 3.8 kernel
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have a built-in
Silicon Motion USB UVC WebCam whose power supply is the tps65090 fet5
regulator. Since the camera uses the generic USB Video Class driver and
this does not grab a regulator, mark the regulator as always on so the
USB device is enumerated and usable.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5420 Peach Pit and Exynos5800 Peach Pi boards have both
a power and lid GPIO keys but only the former was defined in the
DTS. Add DTS snippets for the lid GPIO key too. These were taken
from the downstream ChromeOS 3.8 kernel tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Exynos5250 Snow Chromebook has GPIO keys for power and lid
so the SoC I/O pins have to be configured in external interrupt
mode. Currently, this is working without setting the pinctrl
lines but is better to set it explicitly instead of relying on
the previous state of the I/O pins.
The DTS snippets were taken from the downstream ChromeOS tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add the sample and output clocks for the MMC phase support.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Chen-Yu Tsai <wens@csie.org>
On i.MX28, the MDIO bus is shared between the two FEC instances.
The driver makes sure that the second FEC uses the MDIO bus of the
first FEC. This is done conditionally if FEC_QUIRK_ENET_MAC is set.
However, in newer designs, such as Vybrid or i.MX6SX, each FEC MAC
has its own MDIO bus. Simply removing the quirk FEC_QUIRK_ENET_MAC
is not an option since other logic, triggered by this quirk, is
still needed.
Furthermore, there are board designs which use the same MDIO bus
for both PHY's even though the second bus would be available on the
SoC side. Such layout are popular since it saves pins on SoC side.
Due to the above quirk, those boards currently do work fine. The
boards in the mainline tree with such a layout are:
- Freescale Vybrid Tower with TWR-SER2 (vf610-twr.dts)
- Freescale i.MX6 SoloX SDB Board (imx6sx-sdb.dts)
This patch adds a new quirk FEC_QUIRK_SINGLE_MDIO for i.MX28, which
makes sure that the MDIO bus of the first FEC is used in any case.
However, the boards above do have a SoC with a MDIO bus for each FEC
instance. But the PHY's are not connected in a 1:1 configuration. A
proper device tree description is needed to allow the driver to
figure out where to find its PHY. This patch fixes that shortcoming
by adding a MDIO bus child node to the first FEC instance, along
with the two PHY's on that bus, and making use of the phy-handle
property to add a reference to the PHY's.
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
- mt8135
- mt8127
- mt6598
For mt6592 only the sysirq support was added.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Idho
-----END PGP SIGNATURE-----
Merge tag 'v3.20-next-dts' of https://github.com/mbgg/linux-mediatek into next/dt
Merge "ARM: mediatek: DT changes for v3.20 (round 1)" from Matthias Brugger:
This adds support for the mediatek sysirq and the uarts for the following SoCs:
- mt8135
- mt8127
- mt6598
For mt6592 only the sysirq support was added.
* tag 'v3.20-next-dts' of https://github.com/mbgg/linux-mediatek:
ARM: mediatek: dts: Add uart to Aquaris5
ARM: mediatek: dts: Add uart to mt6589
dt-bindings: add mt6592 compatible string for mediatek sysirq
ARM: mediatek: Add sysirq device node to mt6592 dtsi
ARM: mediatek: dts: Add UART dts for MT8127 and MT8135 boards
DTS: serial: Add bindings document for the Mediatek UARTs
ARM: mediatek: add UART dts for mt8127 and mt8135
ARM: mediatek: Add sysirq in mt6589/mt8135/mt8127 dtsi
Signed-off-by: Olof Johansson <olof@lixom.net>
Current vendor-prefixes.txt already has "ak" prefix for Asahi Kasei Corp
by ae8c4209af2c(of: Add vendor prefix for Asahi Kasei Corp.)
It went through the appropriate review process. But, almost all
Asahi Kasei chip drivers are using "asahi-kasei" prefix today.
(arch/arm/boot/dts/tegra20-seaboard.dts only is using "ak,ak8975",
but there are instances of "asahi-kasei,ak8975" in other dts files.
And drivers/iio/magnetometer/ak8975.c doesn't support "ak,ak8975" prefix)
So, we made a mistake there.
In addition, checkpatch.pl reports WARNING if it is using "asahi-kasei"
prerfix in DT file.
(DT compatible string vendor "asahi-kasei" appears un-documented)
Marking it deprecated and warning with checkpatch is certainly
preferable. So, this patch replace "ak" to "asahi-kasei" in
vendor-prefixes.txt. (and fixup tegra20-seaboard)
OTOH, Asahi Kasei is usually referred to as "AKM", but this patch
doesn't care about it. Because no DT is using that today.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add handling for gta04 tv out chain:
venc -> opa362 -> svideo
Use invert-polarity in venc node because opa362
is doing polarity inversion also.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CM-T3517, CM-T3530 and CM-T3730 features NAND storage chip connected to
GPMC bus.
Add GPMC DT entry into the root DT file omap3-cm-t3x.dtsi, common for
all three modules.
NAND timings are calculated to be safe for CM-T3x devices as it works
now in non DT boot (in this case the timings are updated by U-Boot).
Update GPMC ranges in boards DT files to include all connected devices.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
CSR atlas7 uses Network on Chip(NoC) bus architecture, there are dozens
of MARCOs, in each MARCO, there are dozens of hardware modules.
Signed-off-by: Zhiwu Song <Zhiwu.Song@csr.com>
Signed-off-by: Hao Liu <Hao.Liu@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Add device tree node for the Secure Non-Volatile Storage
(SNVS) on the VF610 platform. The SNVS block also has a
Real Time Counter (RTC).
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
I made a mistake when rebasing Andrey Gusakov's patch adding MLB+ clock to the
R8A7791 device tree, inserting <&hp_clk> into the "clocks" property of the
MSTP8 node at a wrong position, so that the input clocks for MLB+ and IPMMU-SGX
got swapped...
Fixes: 7408d3061d ("ARM: shmobile: r8a7791: add MLB+ clock")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a device node for the System Controller, with subnodes that
represent the hardware power area hierarchy.
Hook up all devices to their respective PM domains.
Add a minimal device node for the Coresight-ETM hardware block, and hook
it up to the D4 PM domain, so the R-Mobile System Controller driver can
keep the domain powered, until the new Coresight code handles runtime
PM.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Renesas sound driver needs #sound-dai-cells settings, but, this usage
is a little bit confusable. It came from ALSA SoC historical reasons.
The sound DAI naming method is different between Single/Multi DAI in
the ALSA framework, and it is used for sound card matching.
And this #sound-dai-cells has relationship to it.
Current SoC dtsi has #sound-dai-cells = <1> as default settings
(= it is assuming that board/platform has multi DAI), and
board/platform side needs to overwrite it if board/platform was single
DAI. This style is more confusable for users.
This patch removes SoC side default settings, and force to set it by
board/platform side.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The "renesas,rcar_sound" compatible property value was never processed
nor documented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The "renesas,rcar_sound" compatible property value was never processed
nor documented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
- add PMU nodes for BG2Q and BG2CD
- add PPI CPU masks for TWD timer interrupts
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=YfUK
-----END PGP SIGNATURE-----
Merge tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin into next/dt
Merge "ARM: berlin: DT changes for v3.20 (round 1)" from Sebastian Hesselbarth:
Berlin DT changes for v3.20 (round 1)
- add PMU nodes for BG2Q and BG2CD
- add PPI CPU masks for TWD timer interrupts
* tag 'berlin-dt-for-3.20-1' of git://git.infradead.org/users/hesselba/linux-berlin:
ARM: dts: berlin: add PPI cpu mask to twd timer interrupts
ARM: dts: berlin: add pmu node for BG2Q and BG2CD
Signed-off-by: Olof Johansson <olof@lixom.net>
A number of arches (EXYNOS/IMX/TEGRA) are separated out into finer grained
definitions whether it be sub ARCH or SOC definitions. The device tree blobs
should only be built if the specific option is enabled that supports that
device or it might be that there's an expectation that the device is supported
when in actual fact it's not. This ensures only the relevant bits are built.
Also standardised the line break between the arch/soc definitions and the
dtbs to be on separate lines for better consistency as per feedback.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Shawn Guo <shawn.guo@freescale.com>
[olof: Fixed stray \ in one of the IMX rules]
Signed-off-by: Olof Johansson <olof@lixom.net>
* Remove legacy r8a7790 SoC and its Lager board code
* Update serial port names on koelsch and lager boards
* Remove console bootargs parameter from lager DT
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=prxC
-----END PGP SIGNATURE-----
Merge tag 'renesas-lager-board-removal-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/cleanup
Merge "Renesas ARM Based SoC Lager Board Removal for v3.20" from Simon Horman:
"The serial port rename changes are not strictly related to lager board
removal from a feature point of view. But the lager portion of this change
depends on board removal to avoid a regression of booting using that code,
And thus it seems to make sense to put here. And it seems best to put the
koelsch and lager serial port rename changes in the same branch.
Likewise the removal of bootargs from lager DT depends on removing lager
board code to avoid a regression when using it and thus I have included
it in the same branch."
* Remove legacy r8a7790 SoC and its Lager board code
* Update serial port names on koelsch and lager boards
* Remove console bootargs parameter from lager DT
* tag 'renesas-lager-board-removal-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: lager dts: Drop console= bootargs parameter
ARM: shmobile: koelsch: Rename SCIF[01] serial ports to ttySC[01]
ARM: shmobile: lager: Rename SCIFA[01] serial ports to ttySC[01]
ARM: shmobile: r8a7790: Remove legacy code
ARM: shmobile: lager: Remove legacy board support
ARM: shmobile: lager-reference: DTS-only board support
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fZ4r
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Updates for v3.20" from Simon Horman:
* Use clock-indices instead of deprecated renesas,clock-indices
* Prepare for r8a73a4 multiplatform support
* Increase clock coverage for r8a779[014]
* Correct r8a7779 clock usage
* Correct LAN9220 VDDVARIO voltage on ape6evm
* Correct QSPI SPI-Flash mode of lager and koelsch
* Correct flash partition label and size on koelsch
* Correct mask for GIC PPI interrupts on r8a779[14]
* Correct BSC bus range on ape6evm-reference
* tag 'renesas-dt-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (30 commits)
ARM: shmobile: r8a7791: add MLB+ clock
ARM: shmobile: r8a7790: add MLB+ clock
ARM: shmobile: ape6evm: Fix LAN9220 VDDVARIO voltage
ARM: shmobile: r8a73a4: Add r8a73a4-ape6evm.dtb to ARCH_SHMOBILE_MULTI
ARM: shmobile: ape6evm: Add keypad to the device tree
ARM: shmobile: ape6evm: Add LEDs to the device tree
ARM: shmobile: ape6evm: synchronize dts with reference platform
ARM: shmobile: ape6evm: fix compatible string for Ethernet controller
ARM: shmobile: r8a7794: Add MMCIF clock to device tree
ARM: shmobile: r8a7794: Add SDHI clocks to device tree
ARM: shmobile: r8a7794: Add I2C clocks to device tree
ARM: shmobile: r8a7779: Add TWD device to DTS
ARM: shmobile: r8a7779: Use MSTP for SCIF clocks
ARM: shmobile: r8a7779: Use R8A7779_CLK_P as SCIF parent clock
ARM: shmobile: r8a7794: Add QSPI clock to device tree
ARM: shmobile: lager: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add SYS-DMAC clocks to device tree
ARM: shmobile: r8a7791: Add IPMMU-SGX clock to device tree
ARM: shmobile: koelsch: Fix QSPI mode of SPI-Flash into mode3
ARM: shmobile: r8a7794: Add USBDMAC[01] clocks to device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
* Replace status value "ok" with "okay"
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2dNp
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt-cleanups-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Merge "Renesas ARM Based SoC DT Cleanups for v3.20" from Simon Horman:
* Replace status value "ok" with "okay"
* tag 'renesas-dt-cleanups-for-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: kzm9g-reference dts: Replace status value "ok" by "okay"
ARM: shmobile: alt dts: Replace status value "ok" by "okay"
ARM: shmobile: koelsch dts: Replace status value "ok" by "okay"
ARM: shmobile: henninger dts: Replace status value "ok" by "okay"
ARM: shmobile: lager dts: Replace status value "ok" by "okay"
ARM: shmobile: armadillo800eva dts: Replace status value "ok" by "okay"
ARM: shmobile: genmai dts: Replace status value "ok" by "okay"
Signed-off-by: Olof Johansson <olof@lixom.net>
atmel_lcdfb needs also uses hclk clock, but AT91SAM9263 doesn't have that
specific clock, so use lcd_clk twice. The same was done in
arch/arm/mach-at91/at91sam9263.c
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The MICBIAS is a supply, should route to MIC while not IN1L.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
The second property of reg is the length, so correct it for timer.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This patch adds MIPI-DSI and MIPI-DSI based S6E63J0X03 AMOLED panel
device nodes for Exynos3250 Rinato board.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds fimd device node which is a display controller
for Exynos3250 Rinato board.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch replaces number by macro in gpio keys for exynos3250 boards.
Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch removes unnecessary property of gpio-keys node. The
gpio-keys driver doesn't use interrupts and interrupt-parent.
Cc: Youngjun Cho <yj44.cho@samsung.com>
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch enables hsotg and usbphy node to use USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds device tree node for hsotg to control USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds device tree node for exynos_usbphy to use USB 2.0 Device.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add DTS for the Hardkernel Odroid XU3. The name of the DTS file is
kept the same as the vendors naming, which means it's prefixed with
exynos5422 instead of exynos5800 as the SoC name even though it
includes the exyno5800 dtsi.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
we should not be mixing address spaces in the reg property like this driver
currently does. This patch updates the driver, dt docs and also the existing
dt nodes to pass the sysconfig offset in the syscon dt property.
This patch breaks DT compatibility! But this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the DT nodes for the extra ehci and ohci usb controllers
on the stih410 SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the dt nodes for the extra usb2 picophys found on
the stih410.
These two picophys are used in conjunction with the extra ehci/ohci usb
controllers also found on the stih410 SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the dt nodes for the usb2 picophy found on the stih407
device family. It is used on stih407 by the dwc3 usb3 controller when
controlling usb2/1.1 devices.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
update the miphy365 phy driver to access sysconfig register offsets via
syscfg dt property.
This is because the reg property should not be mixing address spaces
like it does currently for miphy365. This change then also aligns us
to how other platforms such as keystone and bcm7445 pass there syscon
offsets via DT.
This patch breaks DT compatibility, but this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
MARCO will not be supported any more. it has been replaced by CSR
atlas7.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Due to the special handling of window 13 on Armada 375 and Armada 38x
(similar to Armada XP), the MBus hardware block is *not* compatible
with the one used on Armada 370. Using the Armada 370 compatible
string on Armada 375 and 38x will lead to a non-working device if
window 13 ends up being used.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The A388-GP is a board produced by Marvell that holds
- 1 PCIe slot
- 2 mini PCIe slot (one of them is multiplexed with the PCIe slot,
muxing is selected through the GPIO expander)
- 1 16MB SPI-NOR
- 2 Gigabit Ethernet ports
- 4 SATA ports (2 of them are multiplexed with the mini PCIe slots,
muxing is selected through the GPIO expander)
- 1 SDIO slot
- 1 USB3 port
- 2 USB2 port
- 2 GPIO/interrupts expander on I2C
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This SoC belongs to the Armada 38x family. The main difference with
the Armada 385 is that the 388 can handle two more SATA
ports. Currently the consequence is the use of a different compatible
string for the pinctrl node, in order to be able to use the pins
associated to this 2 new SATA ports. The second SATA controller has
also been moved from the armada38x.dtsi as it it specific to the
Armada388 version.
In the same time the Armada385 DB and Armada 385 RD board have been
renamed in the 388 one and now include the armada-388.dtsi file. AS
both of them have 4 SATA ports the SoC used on them were wrongly
described.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The pintcrl label was missing. Adding it allowed referring it from the
root of the device tree. Also add the uart0 label used by the
bootloader.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
With the Armada 385 GP board more pinctrl functions depending of the
SoC are needed. Add them to the DTSI to avoid duplication.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The A385-AP is a board produced by Marvell that holds 3 mPCIe slot, a 16MB
SPI-NOR, 3 Gigabit Ethernet ports, USB3 and NAND flash storage.
[gregory.clement@free-electrons.com: switch the license to the dual
X11/GPL with the agreement of the author]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Some pinctrl functions can be shared with all DTS out there, since they are
generic, SoC-wide muxing options. Add a number of these to the DTSI to avoid
duplication.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
The compatible set in the armada-38x DTSI is always overridden, and the reg
defined in there is duplicated in the armada-380 and armada-385 DTSIs.
Remove these useless items.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Some nodes in the DTs have a reg property but no unit name in their node name.
This contradicts the way the ePAPR defines the node names. Fix this.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
This patch adds the DT nodes for the extra ehci and ohci usb controllers
on the stih410 SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the dt nodes for the extra usb2 picophys found on
the stih410.
These two picophys are used in conjunction with the extra ehci/ohci usb
controllers also found on the stih410 SoC.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
This patch adds the dt nodes for the usb2 picophy found on the stih407
device family. It is used on stih407 by the dwc3 usb3 controller when
controlling usb2/1.1 devices.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
"isil" and "isl" prefixes are used at various locations inside the kernel
to reference Intersil corporation. This patch is part of a series fixing
those locations were "isl" is used in compatible strings to use the now
expected "isil" prefix instead (NASDAQ symbol for Intersil and most used
version).
Note: isl29028 is an I2C device so the patch does not in fact currently
depend on the introduction of "isil"-based compatible string in isl29028
driver because I2C core does not check the prefix yet.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Cortex-A9 TWD timer has registers at address 0x50040600, but the
unit address was 50004600, most likely a typo.
Signed-off-by: Thierry Reding <treding@nvidia.com>
As 456062b3ec ("ARM: imx: add FEC sleep mode callback function") has been
reverted, also revert the dts part.
This reverts commit 07b4d2dda0 ("ARM: dts: imx6qdl: enable FEC
magic-packet feature").
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DP PHY now require pmu-system-controller to handle PMU register
to control PHY's power isolation. Adding the same to dp-phy
node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add sysirq node to mt6592.dtsi and also correct timer interrupt flag.
The old setting works because boot loader already set it.
With a sysirq device node, the timer interrupt can use a correct value.
Signed-off-by: Howard Chen <howard.chen@linaro.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
This patch enable UART for MT8127 moose board and MT8135 evalution board.
Adding the dts, these two boards can show log and shell prompts.
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Add USB nodes to zc702, zc706 and zed device trees.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
TPS gpio now controls a 5v 500mA TL5209 regulator which may be supply
a fan (such as AFB02505HHB) over J1 connector for various purposes.
Provide device tree node to enable the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x IDK board has a User Switch which we can
program to whatever we want. Because this board
doesn't have a PMIC which can give us power button
presses, let's use this user switch as a gpio-keys
power button.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add twl_power for N950/N9. Start with the simplest configuration to just
enable power off.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let this board report KEY_POWER so upper layers
can decide what to do when power button is pressed.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AM437x Industrial Development Kit (IDK) is
an application development platform targeted at
industrial communication and control applications.
It comes with a 3-phase motor driver, PROFINET,
PROFIBUS and a few other industrial communication
interfaces.
The board has 1GiB of DDR3 RAM, QSPI NOR flash,
a 100% discrete power design (no PMIC) and an
on-board 2MP camera (not supported with Linux
as of this writing).
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am437x gp evm.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am437x sk evm.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add device tree nodes and pinmux entries for Video Processing
Front End (VPFE) on am43x epos evm.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add Video Processing Front End (VPFE) device tree
nodes for AM34xx family of devices.
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since phyid is no longer used by pcie driver, this field can be dropped
from the DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes english in comments and removes extra empty newline.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add CPSW DT binding to beagle X15 DTS in order to
get ethernet working with this board.
Note that we're also adding sleep state which will
place all pins in mux mode 15 - which means "driver
off" - thus conserving power.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The DSS data lines don't need pulls, it's best
to remove them to guarantee signal integrity.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit already has discrete pullups
for all I2C buses, so we can (and should) remove
internal pulls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch just makes USB[01]_DRVVBUS signal
explicitly muxed. Note that board already has
a discrete pulldown, so we're not adding any
pulls here.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM437x Starter Kit already has discrete pulls
where they are necessary. It's safe (and actually
better) to remove internal pulls.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
By don't relying on implicit MMC0 pulldown we
make sure that pins are marked busy and even
if we have a broken bootloader, MMC0 will
remain functional.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The FSI2 sound node used the generic compatible property only.
Add the SoC-specific one, to make it future proof.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
QSPI doesn't need any pullups of any sort,
let's remove them.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Hook dcdc2 as the cpu0-supply.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Tested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 58ecb23f64 ("ARM: tegra: add missing unit addresses to DT") added
unit address and changed reg base for GR3D and DSI host1x modules, but these
addresses belongs to GR2D and TVO modules respectively. Fix it by changing
modules unit and reg base addresses to proper ones.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Fixes: 58ecb23f64 (ARM: tegra: add missing unit addresses to DT)
Cc: <stable@vger.kernel.org> # v3.13+
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The gpio4 and gpio5 are in 0xf7fc0000 apb which is located in the SM domain.
This patch moves gpio4 and gpio5 to the correct location. This patch also
renames them as the following to match the names we internally used in
marvell:
gpio4 -> sm_gpio1
gpio5 -> sm_gpio0
porte -> portf
portf -> porte
This also matches what we did for BG2 and BG2CD's SM GPIO.
Cc: stable@vger.kernel.org # 3.16+
Fixes: cedf57fc4f ("ARM: dts: berlin: add the BG2Q GPIO nodes")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
According to the gic binding document, "bits[15:8] PPI interrupt cpu
mask. Each bit corresponds to each of the 8 possible cpus attached to
the GIC. A bit set to '1' indicated the interrupt is wired to that
CPU." This patch wants to add the PPI cpu mask for completeness.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
This patch adds the pmu node, enabling the PMU unit on Marvell BG2Q and
BG2CD SoCs.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
There's no card detection for the eMMC, so this patch adds the missing
broken-cd property. This patch also sets bus width as 8 to add
MMC_CAP_8_BIT_DATA in the Host capabilities.
Cc: stable@vger.kernel.org # 3.16+
Fixes: 3047086dfd ("ARM: dts: berlin: enable SD card reader and eMMC for the BG2Q DMP")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
On BG2Q, the sdhci2 host uses nfcecc for "io" clk and nfc for "core" clk.
The shdci2 can't work without this patch due to the "core" clk is gated.
Cc: stable@vger.kernel.org # 3.16+
Fixes: 0d859a6a9d ("ARM: dts: berlin: add the SDHCI nodes for the BG2Q")
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Revert "ARM: dts: Disable smc91x on n900 until bootloader
dependency is removed". We've now fixed the issues that
caused problems with uninitialized hardware depending on
the bootloader version. Mostly things got fixed with
the following commits:
9a894953a9 ("ARM: dts: Fix bootloader version dependencies by muxing n900 smc91x pins")
7d2911c438 ("net: smc91x: Fix gpios for device tree based booting")
Note that this only affects the early development boards
with Ethernet that we still have in a few automated boot
test systems. And it's also available supposedly in some
versions of qemu.
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO2_5 is the reset GPIO for the USB3317 ULPI PHY. Instead of modelling it as
a regulator, the correct approach is to use the 'reset_gpios' property of the
"usb-nop-xceiv" node.
GPIO1_7 is the reset GPIO for the USB2517 USB hub. As we currently don't have
dt bindings to describe a HUB reset, let's keep using the regulator approach.
Rename the regulator to 'reg_hub_reset' to better describe its function and bind
it with the USB host1 port instead.
USB host support has been introduced by commit 9bf206a9d1 ("ARM: dts:
imx51-babbage: Add USB Host1 support"), which landed in 3.16 and it seems that
USB has only been functional due to previous bootloader initialization.
With this patch applied we can get USB host to work without relying on the
bootloader.
Cc: <stable@vger.kernel.org> # 3.16+
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For more information about the Udoo boards:
http://www.udoo.org/
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enables the gpio-base mic detection on the Acer Chromebook 13. This
gpio is set by the jack-detection chip when it notices either of the
TRRS type headsets with a microphone.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The Ippo q8h has its serial console connected to the r-uart. Adjust the
serial0 alias to match.
This fixes the kernel serial console no longer working since 3.19-rc1, because
8250_dw.c now honors dt aliases, causing the serial console to be ttyS5 rather
then being ttyS0, as it was in 3.18 and before.
Note that adjusting bootargs instead is not an acceptable fix, because
console=ttyS0,115200 is used by a lot of bootscripts, etc. and this should
continue to work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
64KiB is allocated for qspi dtb partition which is not
sufficient, so updating the partition table size to 512KiB
for device tree partition.
This also aligns the QSPI partition definitions between
kernel and U-Boot.
Fixes: dc2dd5b8 ("ARM: dts: dra7: Add qspi device")
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for Seagate BlackArmor NAS220.
The Seagate BlackArmor NAS 220 is a NAS system based on Marvell 88f6192. It has
32MB NAND and 128MB DRAM. It has two SATA slots, one Gigabit Ethernet port, two
USB 2.0 ports, two buttons and three LEDs. There is a serial port available on
the CN5 connector on the board (1 - TX, 4 - RX, 6 - GND).
The only functionality still not implemented is the bi-color led on the front
panel (status). Pins mpp22 and mpp23 control this led. Setting mpp22 to high and
mpp23 to low results in orange color. Setting mpp22 to low and mpp23 to high
results in blue color.
The third led is wired to show the SATA activity on the two drives.
Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Add basic i.MX6SoloX Sabre Auto board support, currently
only debug UART and uSDHC are supported on this board.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6sx-sdb has two s25fl128s quad spi flash. Add support for them.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
According to Documentation/devicetree/bindings/media/coda.txt:
- clock-names : Should be "ahb", "per"
The OCRAM clock is already provided inside the ocram node, so remove the OCRAM
clock from the VPU node.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
