This fixes compiler warnings:
drivers/net/ethernet/amd/declance.c: In function 'lance_init_ring':
drivers/net/ethernet/amd/declance.c:478: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:487: warning: format '%8.8x' expects type 'unsigned int', but argument 3 has type 'long unsigned int'
drivers/net/ethernet/amd/declance.c:503: warning: cast from pointer to integer of different size
drivers/net/ethernet/amd/declance.c:520: warning: cast from pointer to integer of different size
in 64-bit compilation. Where the value printed is an offset (whose range
will always fit) the cast uses a 32-bit type, otherwise, where it is a
host memory address, the pointer is output directly with %p. Also the
remaining `0x' prefix is dropped for consistency across these messages.
Tested with both 32-bit and 64-bit compilation, as well as at the run time
(with the debug messages affected enabled).
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the system is too busy to complete the urb, the tx timout function
would be called. This causes the other tx urbs would be killed, too.
Increase the tx timeout to avoid it.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In xennet_disconnect_backend(), netif_carrier_off() was called once
per queue when it needs to only be called once.
The queue locking around the netif_carrier_off() call looked very
odd. I think they were supposed to synchronize any NAPI instances with
the expectation that no further NAPI instances would be scheduled
because of the carrier being off (see the check in
xennet_rx_interrupt()). But I can't easily tell if this works
correctly.
Instead, add a napi_synchronize() call after disabling the interrupts.
This is obviously correct as with no Rx interrupts, no further NAPI
instances will be scheduled.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nesting of the per-queue rx_lock and tx_lock in xennet_connect()
is confusing to both humans and lockdep. The locking is safe because
this is the only place where the locks are nested in this way but
lockdep still warns.
Instead of adding the missing lockdep annotations, refactor the
locking to avoid the confusing nesting. This is still safe, because
the xenbus connection state changes are all serialized by the xenwatch
thread.
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
The add_vxlan_port ndo driver code was wrongly testing whether HW vxlan offloads
are supported by the device instead of checking if they are currently enabled.
This causes the driver to configure the HW parser to conduct matching for vxlan
packets but since no steering rules were set, vxlan packets are dropped on RX.
Fix that by doing the right test, as done in the del_vxlan_port ndo handler.
Fixes: 1b136de ('net/mlx4: Implement vxlan ndo calls')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The default cache operations for ARM64 were changed during 3.15.
To use coherent operations a "dma-coherent" device tree property
is required. If that property is not present in the device tree
node then the non-coherent operations are assigned for the device.
Add support to the amd-xgbe driver to assign the AXI DMA cache settings
based on whether the "dma-coherent" property is present in the device
node. If present, use settings that work with the caches. If not
present, use settings that do not look at the caches.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch provides some general performance enhancements for the
driver:
- Modify the default coalescing settings (reduce usec, increase frames)
- Change the AXI burst length to 256 bytes (default was 16 bytes which
was smaller than a cache line)
- Change the AXI cache settings to write-back/write-allocate which
allocate cache entries for received packets during the DMA since the
packet will be processed soon afterwards
- Combine ioread/iowrite when disabling both the Tx and Rx interrupts
- Change to processing the Tx/Rx channels in pairs
- Only recycle the Rx descriptors when a threshold of dirty descriptors
is reached
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the napi context is added using netif_napi_add each time
the ndo_open operation is called. However, there is not a
corresponding netif_napi_del call during the ndo_stop operation. If
the device ndo_open operation was called more than once an infinite
loop occurs during module unload. Add a call to netif_napi_del during
the ndo_stop operation.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When initializing the MTL interrupts the interrupt status
register is written to instead of the interrupt enable register.
Since no MTL interrupts are being enabled and the default state
is for MTL interrupts to be disabled this did not cause a problem,
but needs to be fixed to target the correct register.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The initial change from sscanf to kstrtouint broke backward
compatbility by using a base of "0" in the kstrtouint call.
This allowed for entering decimal, hexadecimal or octal as
input where previously the sscanf always interpreted the input
as hexadecimal. Additionally, -EIO was returned on error prior
to this change and now it is whatever the error value that is
returned by kstrtouint.
Change the base value of the kstrtouint from 0 to 16 and return
-EIO on error.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
enic_set_coalesce() has two problems.
* It should return -EINVAL and not -EOPNOTSUPP for invalid coalesce values.
* In case of MSIX, enic_set_coalesce return error after applying requested
coalescing setting partially. We should either apply all the setting requeste
and return success or apply non and return error.
* This patch also simplifies the algo.
This was introduced by
'7c2ce6e60f703 enic: Add support for adaptive interrupt coalescing'
These changes were suggested by Ben Hutchings here
http://www.spinics.net/lists/netdev/msg283972.html
Also change enic driver version.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warnings are no longer relevant. Even when last slave is
removed, there is a valid address assigned to bond (random).
The correct functionality of vlans is ensured by maintaining unicast
list in vlan_sync_address().
Suggested-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the current synchron state change function and add a
new function for a state assert. Change the start and stop callbacks to
use this new synchron state change behaviour. It's a wrapper around the
async state change function.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rework the irq_pol register setting for rising and falling
interrupt settings only. The default behaviour should be rising flag.
Also use IRQ_TYPE_* defines instead of IRQF_* defines. There is no
functionality change but irq_get_trigger_type returns IRQ_TYPE_* defines.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to set this bit in start callback which could be
called more than once.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a complete reimplementation of transmit and receive
handling for the at86rf230 driver.
It solves also six bugs:
First:
The RX_SAFE_MODE is enabled and the transceiver doesn't leave the
receive state while the framebuffer isn't read by a CMD_FB command.
This is useful to read out the frame and don't get into another receive
or transmit state, otherwise the frame would be overwritten.
The current driver do twice CMD_FB calls, the first one leaves this
protection.
Second:
Sometimes the CRC calculation is correct and the length field is greater
127. The current mac802154 layer and filter of a at86rf2xx doesn't check
on this and the kernel crashes. In this case the frame is corrupted, we
send the whole receive buffer to the next layer which can be useful for
sniffing.
Thrid:
There is a undocumented race condition. When we are go into the
RX_AACK_ON state the transceiver could be changed into RX_AACK_BUSY
state. This is a normal behaviour. In this case the transceiver received
a SHR while assert wasn't finished.
Fourth:
It also handle some more "correct" state changes. In aret mode the
transceiver need to go to TX_ON before the transceiver go into
RX_AACK_ON.
Fifth:
The programming model [0] describes also a error handling in ARET mode
if the trac status is different than zero. This is patch adds support
for handling this.
Sixth:
In receive handling the transceiver should also get the trac status
according [0]. The driver could use the trac status as error statistic
handling, but the driver doesn't use this currently. There is maybe some
timing behaviour or the read of this register change some transceiver
states.
In addition the irqworker is removed. Instead we do async spi calls and
no scheduling is involved anymore. The transmit function is also
asynchron but with a wait_for_completion handling. The mac802154 layer
doesn't support asynchron transmit handling right now.
The state change behaviour is now changes, before it was:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. assert while(!STATE_TRANSITION_IN_PROGRESS)
4. assert once(wanted state != current state)
Sometimes a unexcepted state change occurs when 4. assert was violated.
The new state change behaviour is:
1. assert while(!STATE_TRANSITION_IN_PROGRESS)
2. state change
3. wait state change timing according datasheet
4. assert once(wanted state != current state)
This behaviour is described in the at86rf231 software programming model [0].
The state change documentation in this programming guide should also valid for
at86rf212 and at86rf233 chips.
The transceiver don't do a FORCE_TX_ON while we want to transmit a PDU.
The new behaviour is a TX_ON and wait a receiving time (tFrame + tPAck).
If we are still in RX_AACK_BUSY then we transmit a FORCE_TX_ON as timeout
handling. The different is that FORCE_TX_ON aborts receiving and TX_ON
waits if RX_AACK_BUSY is finished. This should decrease the drop rate of
packets.
[0] http://www.atmel.com/Images/AVR2022_swpm231-2.0.zip
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To set the CCA_ED_THRES register the calculation for at86rf23x is
different than for at86rf212. This patch adds a new callback for this
calculation in chip data struct.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new at86rf2xx_chip_data structure which holds device
specific attributes. Instead of runtime decisions "if (is212())" we set
callbacks/attributes while device detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch drops the current lowlevel spi calls for the detect device
function instead we handle this via regmap. Also put the detection of
in a seperate function and set all device specific attributes while detection.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds regmap support for the at86rf230 driver and drop the
lowlevel spi access functions and use the regmap access functions.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds new mac802154 hw flags for transmit power, csma and
listen before transmit (lbt). These flags indicates that the transceiver
supports these features. If the flags are set and the driver doesn't
implement the necessary functions, then ieee802154_register_device
returns -ENOSYS "Function not implemented".
This patch merges also all at86rf230 operations into one operations structure
and set the right hw flags for the at86rf230 transceivers.
Signed-off-by: Alexander Aring <alex.aring@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-02
This series contains updates to i40e and i40evf.
Anjali fixes a possible race where we were trying to free the dummy packet
buffer in the function that created it, so cleanup the dummy packet buffer
in i40e_clean_tx_ring() instead. Also fixes an issue where the filter
program routine was not checking if there were descriptors available for
programming a filter.
Mitch fixes unnecessary delays when sending the admin queue commands by
moving a declaration up one level so we do not dereference it out of scope.
Fixes an issue with the VF where if the admin queue interrupts get lost for
some reason, the VF communication will stall as the VFs have no way of
reaching the PF. To alleviate this condition, go ahead and check the ARQ
every time we run the service task. Updates i40evf to allow the watchdog
to fire vector 0 via software, which makes the driver tolerant of dropped
interrupts on that vector.
Paul fixes a shifted '1' to be unsigned to avoid shifting a signed integer.
Jesse disables TPH by default since it is currently not enabled in the
current hardware. Also finishes the i40e implementation of get_settings
for ethtool.
Catherine adds a new variable (hw.phy.link_info.an_enabled) to track whether
auto-negotiation is enabled, along with the functionality to update the
variable. Adds the functionality to set the requested flow control mode.
Adds i40e implementation of setpauseparam and set_settings to ethtool.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
fec_enet_alloc_buffers() assumes that kmalloc() will never fail, which
is an invalid assumption. Fix this by implementing a common error
cleanup path, and use it to also clean up after failed bounce buffer
allocation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ensure that we do not double-free any allocations, and that any transmit
skbuffs are properly freed when we clean up the rings.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid writing any state until we're certain we can proceed with the
transmission: this avoids writing mapping error address values to the
descriptors, or setting the skbuff pointer until we have successfully
mapped the skb.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allocate, and then map the receive skb before writing any data to the
ring descriptor or storing the skb. When freeing the receive ring
entries, unmap and free the skb, and then clear the stored skb pointer.
This means we have ring data and skb pointer in one of two states:
either both fully setup, or nothing setup.
This simplifies the cleanup, as we can use just the skb pointer to
indicate whether the descriptor is setup, and thus avoids potentially
calling dma_unmap_single() on a DMA error value.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_disable() waits until the NAPI processing has completed, and then
prevents any further polls. At this point, the driver then clears
fep->opened. The NAPI poll function uses this to stop processing in
the receive path. Hence, it will never see this variable cleared,
because the NAPI poll has to complete before it will be cleared.
Therefore, this variable serves no purpose, so let's remove it.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the network interface goes down, stop the phy to prevent further
link up status changes before taking the MAC or netif sections down.
This prevents further reception of link up events which could
potentially call fec_restart().
Since phy_stop() takes the mutex which adjust_link() runs under, we
also ensure that adjust_link() will not already be processing a link
up event.
We also need to do this when suspending as well - we don't want a
mis-timed phy state change to restart the MAC after we have stopped
it for suspend, and thus need to restart the phy when resuming.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disconnect from a phy, we should forget our pointer to it so we
don't accidentally try to configure it. We handle a NULL phy pointer
correctly in most places, except fec_enet_set_pauseparam(). Fix this
too.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
fep->phy_dev can not be NULL here for two reasons:
- fec_enet_open() will have successfully connected the phy, or will have
failed.
- fec_enet_open() will have called phy_start(fep->phy_dev), which
unconditionally dereferences this pointer.
If it were to be NULL here, then fec_enet_open() will have already
oopsed.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use netif_stop_queue() in several places where we want to ensure that
the start_xmit function is not running. netif_stop_queue() is not
sufficient to achieve that - it merely sets a flag to indicate that the
transmit queue(s) should not be run.
netif_tx_disable() gives this guarantee, since it takes the transmit
queue lock while marking the queue stopped. This will wait for the
transmit function to complete before returning.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
While running: while :; do iperf -c <HOST> -P 4; done, transmit timeouts
are regularly reported. With the tx ring dumping in place, we can see
that all entries are in use, and the hardware has finished transmitting
these packets. However, the driver has not reclaimed these ring
entries.
This can occur if the interrupt handler is invoked at the wrong moment -
eg:
CPU0 CPU1
fec_enet_tx()
interrupt, IEVENT = FEC_ENET_TXF
FEC_ENET_TXF cleared
napi_schedule_prep()
napi_complete()
The result is that we clear the transmit interrupt, but we don't trigger
any cleaning of the transmit ring. Instead, use a different strategy:
- When receiving a transmit or receive interrupt, disable both tx and rx
interrupts, but do not acknowledge them. Schedule a napi poll. Don't
loop.
- When we are polled, read IEVENT, acknowledging the pending transmit
and receive interrupts, before then going on to process the
appropriate rings.
This allows us to avoid the race, and has a number of other advantages:
- we cut down on the number of transmit interrupts we have to process.
- we only look at the rings which have pending events.
- we gain additional throughput: the iperf total bandwidth increases
from about 180Mbps to 240Mbps:
[ 3] 0.0-10.0 sec 68.1 MBytes 57.0 Mbits/sec
[ 5] 0.0-10.0 sec 72.4 MBytes 60.5 Mbits/sec
[ 4] 0.0-10.1 sec 76.1 MBytes 63.5 Mbits/sec
[ 6] 0.0-10.1 sec 71.9 MBytes 59.9 Mbits/sec
[SUM] 0.0-10.1 sec 288 MBytes 241 Mbits/sec
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting the pause parameters causes a running network interface to be
restarted. However, the restart forces the FEC into half-duplex mode,
whether or not the remote end is in half-duplex mode. Misconfigured
duplex mode is a known source of problems on a link.
Fix this by always preserving the duplex mode on configuration changes.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The iMX6 gigabit FEC does not support half-duplex gigabit operation.
Phys attacked to the FEC may support this, and we currently do nothing
to disable this feature. This may result in an invalid configuration.
Mask out phy support for gigabit half-duplex operation.
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
In vxlan and OVS vport-vxlan call common function to get source port
for a UDP tunnel. Removed vxlan_src_port since the functionality is
now in udp_flow_src_port.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Support for Wake-on-LAN using Magic Packet with or without SecureOn
password is implemented doing the following:
- setting the password to the relevant UniMAC registers
- flagging the device as a wakeup source for the system, as well as
its Wake-on-LAN interrupt
- prepare the hardware for entering WoL mode
- enabling the MPD interrupt to wake us
The Device Tree binding documentation is also reflected to specify the
third optional Wake-on-LAN interrupt line.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This boolean tells us whether we are using the RXCHK hardware block,
so use a variable name that reflects that. RXCHK might be used in the
future to implement Wake-on-LAN using ARP or unicast packets.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware recommended suspend/resume procedure for
SYSTEMPORT. We leverage the previous factoring work such that we can
logically break all suspend/resume operations into disctint RX and TX
code paths.
When the system enters S3, we will loose all register contents, so
make sure that we correctly re-program all the hardware and software
views of the RX & TX rings as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor common code that either enables or disables the network
interface with the networking stack. We are going to reuse these
functions for suspend/resume callbacks.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quite often we need to enable either the transmitter or the receiver
bits in UMAC_CMD, use umac_enable_set() to do that for us.
This is a preliminary change to introduce suspend/resume support in the
driver.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a new version of the Telewell 4G modem working with, but not
recognized by this driver.
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0acf167687.
Breaks the build due to missing reference to phy_resume in
the resulting dwmac-socfpga.o object.
Signed-off-by: David S. Miller <davem@davemloft.net>
deal with a compile warning: comparison between
'enum qe_fltr_largest_external_tbl_lookup_key_size'
and 'enum qe_fltr_tbl_lookup_key_size'
the code:
"if (ug_info->largestexternallookupkeysize ==
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES)"
is warned because different enum, so modify it.
"enum qe_fltr_largest_external_tbl_lookup_key_size
largestexternallookupkeysize;
enum qe_fltr_tbl_lookup_key_size {
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES
= 0x3f, /* LookupKey parsed by the Generate LookupKey
CMD is truncated to 8 bytes */
QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES
= 0x5f, /* LookupKey parsed by the Generate LookupKey
CMD is truncated to 16 bytes */
};
/* QE FLTR extended filtering Largest External Table Lookup Key Size */
enum qe_fltr_largest_external_tbl_lookup_key_size {
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_NONE
= 0x0,/* not used */
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_8_BYTES
= QE_FLTR_TABLE_LOOKUP_KEY_SIZE_8_BYTES, /* 8 bytes */
QE_FLTR_LARGEST_EXTERNAL_TABLE_LOOKUP_KEY_SIZE_16_BYTES
= QE_FLTR_TABLE_LOOKUP_KEY_SIZE_16_BYTES, /* 16 bytes */
};"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using internal 10 Mbps PHY, isolate the external PHY from MII bus.
External PHY must be kept powered up because it passes TX from tlan chip to
network.
This fixes weird link-loss problems under load with OC-2326 card at 10 Mbps.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
pci_disable_device() is called in _suspend but there's no corresponding
pci_enable_device() in _resume.
This causes "disabling already-disabled device" warning on 2nd suspend.
Add pci_enable_device() call to _resume to fix this problem.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In tlan_reset_adapter, we disable internal PHY when an external one is used.
On cards which use internal PHY in 10 Mbps mode, we enable it later when
setting 10 Mbps mode but it does not really work (PHY fails to reset).
Leave it enabled instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a timeout to prevent infinite loop waiting for PHY to reset.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the autonegotiation poll interval from 8 seconds to 2.
This greatly reduces the time needed to detect link presence,
especially on Olicom cards at 10 Mbps (two autonegoatiations required).
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove excess printks when the link is down.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When link is lost on a card which uses internal PHY for 10 Mbit speeds,
restart autonegotiation to allow switching between 10 and 100 Mbps speeds.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 cards have the MAC address byte-swapped in EEPROM.
Byte-swap the MAC address if it's located at offset 0xF8.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic ethtool support to tlan driver:
- driver info - link detect (this allows NetworkManager to detect carrier)
- EEPROM read
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable old link monitoring code and modify it:
- control LINK LED
- use separate timer so it does not interfere with ACT LED
Tested with Olicom OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Olicom OC-2325 and OC-2326 ethernet cards have an activity LED but it does not
work with tlan driver as it's not enabled. Enable it.
Tested with OC-2326.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This extends the ptp bpf to also match ptp over ip over vlan packets. The ptp
classes are changed to orthogonal bitfields representing version, transport
and vlan values to simplify matching.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes
b43-phy0: Found Radio: Manuf 0x17F, Version 0x7769, Revision 4
to the
b43-phy0: Found Radio: Manuf 0x17F, Version 0x2069, Revision 4
which matches what closed source driver reports:
$ wl revinfo
radiorev 0x42069000
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This allows adding more revisions support, spotting lacking tables and
unifies naming schema.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The comment was not accurate, we are talking about the frames
*for* the station and not from the station.
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch removes the setting of the ADC sampling bits in
the mvm nic configuration. This setting is not required by
the firmware, and furthermore - it interferes with the DBGC
when it is running in DRAM mode on PCIe.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Reviewed-by: Dor Shaish <dor.shaish@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW currently doesn't optimally support TDLS in DCM mode. Teardown
all TDLS peers when we have more than a single phy context.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The FW does not support PSM on a vif with associated TDLS peers. Disable
PSM when the first peer joins and re-enable it when the last leaves.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Use the new mac80211 callback to protect a TDLS discovery session so we
can hear the discovery-response packet.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
HW/FW constraints dictate that TDLS should only be used when a single
phy ctx is active. We also support at most 4 TDLS peers. We don't
support TDLS on a P2P vif.
Unify and move a phy-ctx counting implementation from the power-mgmt code
in order to simplify implementation.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
An AP/GO may perform the channel switch slightly before its stations.
This scenario may result in packet loss, since the transmission may start
before the client is actually on a new channel. In order to prevent
potential packet loss disable tx to all the stations when the channel
switch flow starts. Clear the disable_tx bit when a station is seen on a
target channel, or after IWL_MVM_CS_UNBLOCK_TX_TIMEOUT beacons on a new
channel. In addition call ieee80211_sta_block_awake in order to inform
mac80211 that the frames for this station should be buffered.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
According to the spec, GO/AP should perform the channel switch just
before "beacon 0". However, since the exact timing isn't defined,
it may result in a sudden GO disappearance from the channel.
Prevent potential packet loss when performing the CS by scheduling
NoA time event and executing the channel switch flow when a notification
from fw is received.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently mvm->csa_vif is protected with mvm mutex. The RCU protection
is required for "iwlwifi: mvm: Reflect GO channel switch in NoA" patch.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Call ieee80211_beacon_get_template instead of ieee80211_beacon_get and sync the
CSA counters with mac80211 after each beacon transmission.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement support for unbind-bind flow for the client roles. This
includes telling the firmware that we are not associated, removing
time-events, removing quotas and updating power management during the
actual switch, and redoing everything in the new channel.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Implement the switch_vif_chanctx operation with support for a
single-vif and SWAP mode. The REASSIGN mode and multi-vifs are not
supported yet.
This operation needs to implement 4 steps, namely unassign, remove,
add and assign the chanctx. In order to do this, split out these
operations into locked and non-locked parts, thus allowing us to call
them while locked.
Additionally, in order to allow us to restart the hardware when
something fails, add a boolean to the iwl_mvm_nic_restart() function
that tells whether the restart was triggered by a FW error or
something else.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
It turns out that adding the update type argument was pointless as
quota update is never called from the add_interface() callback.
Therefore, IWL_MVM_QUOTA_UPDATE_TYPE_NEW isn't actually needed and
then only a "disabled_vif" argument is needed for the upcoming CSA
work.
Remove the whole enum iwl_mvm_quota_update_type and pass the right
arguments (always NULL for disabled vif right now) to the function
in all current call sites.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Simplify the quota iterator by not passing the update type,
it only needs to know whether or not to skip an interface.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware currently deals with zero quota for a given
binding, but it seems odd to send that down. Make sure
that we don't do that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are some cases where we can currently send zero quota
for a valid binding, e.g. if we update while an interface is
bound to a channel context but not yet acting as an AP.
Avoid this by reordering the checks.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In some cases (e.g. when we're doing a channel switch), we may need to
disable the quota of a vif temporarily. In order to do so, add an
argument to the iwl_mvm_update_quotas() function to tell if the passed
vif is a new one or if it should be disregarded.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
when driver takes the MAC address from the HW section and
it isn't valid - print an error.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Initialize LMAC scan command.
Fix EBS flag to be dependant on TLV flg and fix other bugs.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add new scan API that uses the same command 0x51 for both regular and
sched scan.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
These file are removed recursively anyway, so there's no
point saving them just to redundantly remove them later.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_rs_rate_init() is called multiple times to re-init
the rate scaling statistics (e.g. after some idle time).
It clears all the lq_sta sta, including some fields that
shouldn't be cleared (e.g. debugfs pointers). Fix it
by adding a new 'persistent' sub-struct, and
avoid clearing it on (re-)init.
Move the initialization of the persistent fields to
rs_alloc_sta instead.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TxTxCo-Running is active, we can relax the constraints
on the rate control.
When RxRxCo-Running is active, we can relax the constrains
on SMPS.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
No need to send the big BT_COEX_CMD command, we have now
a much thiner command that updates only what is needed.
Adapt the code to that, and open the patch to the updates.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Start the new BT Coex implementation.
Don't react to notifications for now - only the initial
configuration is implemented. The rest will happen in next
patches.
Since coex.c now uses the new the new structures in all
functions, we need to adapt the code to compile, even if it
doesn't run yet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
A new API is coming. This new API is not backward
compatible. So we need to keep the old commands to be able
to work with the former API.
Move all the current code into a new file: coex_legacy.
If a firmware with the new API is detected, we currently
just bail out since the implementation of the new API will
come in future patches.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
In family 8000 products the MAC address in the OTP could be in either:
- WFPM address
- PCIE address
In sdio product we should read it from the WFPM, in pcie product we
should read it from the PCIe location.
This is relevant only from otp version 0xE08 and above.
While at it, fix the bytes order in version 0xE08.
Signed-off-by: Eran Harary <eran.harary@intel.com>
Reviewed-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
This patch makes sure there're no target accesses in the add
interface flow before d0i3 exit completes.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Its content can move to the caller.
While at it, move iwl_mvm_fw_error_rxf_dump to caller.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Instead of reading all the data in the context of the
interrupt thread, collect the data in the restart flow
before the actual restart takes place so that the device
still has all the information.
Remove iwl_mvm_fw_error_sram_dump and move its content to
iwl_mvm_fw_error_dump.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There are few places at the begining of Tx/Rx paths where
tx_info/rx_info is not correctly initialized. This patch
takes care of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Firmware folks seem say that this flag can make trouble.
Drop it. The advantage of CTS to self is that it slightly
reduces the cost of the protection, but make the protection
less reliable.
Cc: <stable@vger.kernel.org> [3.13+]
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We should always prefer to use full RTS protection. Using
CTS to self gives a meaningless improvement, but this flow
is much harder for the firmware which is likely to have
issues with it.
CC: <stable@vger.kernel.org>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Bump.
Change-ID: Ie0c36583ffd9997679f46bdf89bc462d3e992995
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement set_settings for ethtool in i40e.
Change-ID: Ie3c3fe18e8ff86c3f25b842844b3d9aabc9bba57
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add i40e implementation of setpauseparam to ethtool.
Change-ID: Ie7766b2091ec8f934737573c9ffd426081966718
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add function set_fc to set the requested FC mode. This patch also
adds the init of FC setting to get_link_info and replaces the init
code to set FC off by default in main. Also adds i40e_set_phy_config
to support this.
Change-ID: I7b25bbaec81f15777137ab324a095f916e44351d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Just move nway reset up, will be used in the next patch.
Change-ID: Ice3b631fa2044debc5c4541b42872a48163f8452
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a new variable, hw.phy.link_info.an_enabled, to track whether autoneg is
enabled. Also add a new function update_link_info that will update that
variable as well as calling get_link_info to update the rest of the link info.
Also add get_phy_capabilities to support this.
Change-ID: I5157ef03492b6dd8ec5e608ba0cf9b0db9c01710
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Finish the i40e implementation of get_settings for ethtool.
Change-ID: Iec81835aa9380723ae9288bcb79b30a6a1ecd498
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
TPH is not currently enabled in this product, make sure it
isn't enabled by default.
Change-ID: Ibb1a10799c33c4c76dec06fcd53b1d6efa13c1f5
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When turning off ntuple with a FD table full situation,
the driver would have auto disabled FD filter additions.
Clear the auto disable flag for FD_SB so that when the
feature is turned on again using "ethtool -K ethx ntuple on"
we can start adding filters once again.
Change-ID: I036a32e7331bcae765b657c8abb4fa070940b163
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The i40evf_irq_enable and i40evf_fire_sw_interrupt functions were
unfairly discriminating against MSI-X vector 0, just because it doesn't
handle traffic. That doesn't mean it's not essential to the operation of
the driver. This change allows the watchdog to fire vector 0 via
software, which makes the driver tolerant of dropped interrupts on that
vector.
Buck up, vector 0! You can be part of our gang!
Change-ID: I37131d955018a6b3e711e1732d21428acd0d767e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the AQ interrupt gets lost for some reason, VF communications will
stall as the VFs have no way of reaching the PF, which is essentially
deaf. The VFs end up waiting forever for a reply that will never come.
To alleviate this condition, go ahead and check the ARQ every time we
run the service task. Remove the check for a pending event, and get rid
of a chatty error message that is now meaningless.
Change-ID: I0fc9d18169cd45c98f60188aef872cd6cee9a027
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Force a shifted '1' to be unsiged to avoid shifting a signed int
Change-ID: I688cbd082af0f2e1df548fda25847a5ca04babcf
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move a declaration up one level so we don't dereference it out of scope.
This didn't cause any panics, but the details->async field would
mysteriously disappear, causing unnecessary delays when sending AQ
commands. Also, the code is just plain wrong.
Change-ID: I753f64f13c55e5d75ea4351e29b14fb53b2f0104
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The HW still needs to consume it and freeing it in the function
that created it would mean we will be racing with the HW. The
i40e_clean_tx_ring() routine will free up the buffer attached once
the HW has consumed it. The clean_fdir_tx_irq function had to be fixed
to handle the freeing correctly.
Cases where we program more than one filter per flow (Ipv4), the
code had to be changed to allocate dummy buffer multiple times
since it will be freed by the clean routine. This also fixes an issue
where the filter program routine was not checking if there were
descriptors available for programming a filter.
Change-ID: Idf72028fd873221934e319d021ef65a1e51acaf7
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While adding vlans, when the HW limit of vlan filters is reached, the
driver enables vlan promiscuous mode.
Similarily, while removing vlans, the driver must re-enable HW filtering
as soon as the number of vlan filters is within the HW limit.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SR-IOV is enabled in the adapter, the FW distributes queue resources
evenly across the PF and it's VFs. If the user is not interested in enabling
VFs, the queues set aside for VFs are wasted.
This patch adds support for the PF driver to re-configure the resource
distribution in FW based on the number of VFs enabled by the user.
This also allows for supporting RSS queues on VFs, when less number of VFs
are enabled per PF. When maximum number of VFs are enabled, each VF typically
gets only one RXQ.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF driver must query the FW for VF's interface capabilities
to know if the VF is RSS capable or not.
This patch is in preparation for enabling RSS on VFs on Skyhawk-R.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix be_cmd_get_profile_cmd() to use be_cmd_notify_wait() routine,
which uses MBOX if MCCQ has not been created. Doing this reduces
code duplication; we don't need the _mbox/_mccq() variants anymore.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a case where a local variable was being assigned a value,
but not used. There seems to be no reason to read this register before
assigning a new value, so addressing thie issue.
cppcheck --force --enable=all --inline-suppr . shows ...
Variable 'value' is reassigned a value before the old one has been used.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a duplicate if/then/else case where a receive descriptor
was being processed. This patch corrects that issue.
cppcheck --force --enable=all --inline-suppr .
...
Checking enh_desc.c...
[enh_desc.c:148] -> [enh_desc.c:144]: (style) Found duplicate if expressions.
...
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to remove affinity hint at mlx4_en_deactivate_cq() and not at
mlx4_en_destroy_cq() - since affinity_mask might be free'd while still
being used by procfs.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IRQ affinity notifier can only have a single notifier - cpu_rmap
notifier. Can't use it to track changes in IRQ affinity map.
Detect IRQ affinity changes by comparing CPU to current IRQ affinity map
during NAPI poll thread.
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ben Hutchings <ben@decadent.org.uk>
Fixes: 2eacc23 ("net/mlx4_core: Enforce irq affinity changes immediatly")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes compilation warnings:
drivers/net/fddi/defxx.c:294: warning: 'dfx_rcv_flush' declared inline after being called
drivers/net/fddi/defxx.c:294: warning: previous declaration of 'dfx_rcv_flush' was here
drivers/net/fddi/defxx.c:2854: warning: 'my_skb_align' defined but not used
triggered when the driver is built with DYNAMIC_BUFFERS undefined. Code
tested to work just fine with these changes and a few DEFPA and DEFTA
boards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX handler of the driver has two paths switched between, depending on
the size of the frame received, as determined by SKBUFF_RX_COPYBREAK.
When a small frame is received, a new skb allocated has data space large
enough to hold the incoming frame only, and data is copied there from the
original skb whose buffer is returned to the DMA RX ring; in that case
`rx_in_place' is 0. When a large frame is received, a new skb allocated
has data space large enough to hold the largest frame possible, including
the overhead for alignment, the receive status and padding, over 4.5kiB
overall, and its buffer is placed on the DMA RX ring while the original
buffer is passed up to the network stack avoiding the need to copy data;
in that case `rx_in_place' is 1.
However the latter scenario is only possible when dynamic buffers are
used, as determined by DYNAMIC_BUFFERS, because otherwise the buffers used
for the DMA RX ring are fixed at the time the interface is brought up.
That leads to an observation that the preprocessor conditional around the
`rx_in_place' check is inverted, the check only really matters when
dynamic buffers are in use. It has gone unnoticed for many years since
support for using dynamic buffers on the DMA RX ring was introduced in
2.1.40 -- because the only problem that results is in the case where
`rx_in_place' is 1 frame data received is unnecessarily copied to the
newly-allocated buffer, before the buffer placed on the the DMA receive RX
and its contents ignored. Therefore the only symptom is some performance
loss.
Rather than flipping the condition though I decided to discard the
conditional altogether -- in the case of static buffers `rx_in_place' is
always 0 so GCC will optimise the C conditional away instead.
Tested on a few DEFPA and DEFTA boards successfully using both small and
large frames, both with DYNAMIC_BUFFERS defined and with the macro
undefined.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since consume_skb() (and hence dev_kfree_skb() macro) checks the passed pointer
for NULL, there's no need to check for NULL before invoking dev_kfree_skb().
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Collect a firmware dump on first Tx timeout if netif_msg_tx_err() is set
- Log Receive and Status ring info on Tx timeout, in addition to Tx ring info
- Log additional Tx ring info if netif_msg_tx_err() is set
Signed-off-by: Harish Patil <harish.patil@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix checkpatch warning:
"WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required"
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev()) introduced a
circular dependency between libphy and of_mdio.
depmod: ERROR: <modroot>/kernel/drivers/net/phy/libphy.ko in
dependency cycle!
depmod: ERROR: <modroot>/kernel/drivers/of/of_mdio.ko in dependency cycle!
The problem is that of_mdio.c references &mdio_bus_type and libphy now
references of_mdiobus_link_phydev.
Fix this by not exporting of_mdiobus_link_phydev() from of_mdio.ko.
Make it a static function in mdio_bus.c instead.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Jeff Mahoney <jeffm@suse.com>
Fixes: 86f6cf4127 (net: of_mdio: add of_mdiobus_link_phydev())
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-06-27
Please pull the following batch of fixes for the 3.16 stream...
For the mac80211 bits, Johannes says:
"We have a fix from Eliad for a time calculation, a fix from Max for
head/tailroom when sending authentication packets, a revert that Felix
requested since the patch in question broke regulatory and a fix from
myself for an issue with a new command that we advertised in the wrong
place."
For the bluetooth bits, Gustavo says:
"A few fixes for 3.16. This pull request contains a NULL dereference fix,
and some security/pairing fixes."
For the iwlwifi bits, Emmanuel says:
"I have here a fix from Eliad for scheduled scan: it fixes a firmware
assertion. Arik reverts a patch I made that didn't take into account
that 3160 doesn't have UAPSD and hence, we can't assume that all
newer firmwares support the feature. Here too, the visible effect
is a firmware assertion. Along with that, we have a few fixes and
additions to the device list."
For the ath10k bits, Kalle says:
"Bartosz fixed an issue where we were not able to create 8 vdevs when
using DFS. Michal removed a false warning which was just confusing
people."
On top of that...
Arend van Spriel fixes a 'divide by zero' regression in brcmfmac.
Amitkumar Karwar corrects a transmit timeout in mwifiex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-07-01
This series contains updates to i40e, i40evf, igb and ixgbe.
Shannon adds the Base Address High and Low to the admin queue structure
to simplify the logic in the configuration routines. Also adds code to
clear all queues and interrupts to help clean up after a PXE or other
early boot activity.
Kevin fixes mask assignment value since -1 cannot be used for unsigned
integer types.
Mitch fixes an issue where in some circumstances the reply from the PF
would come back before we were able to properly modify the admin queue
pending and required flags. This would mess up the flags and put the
driver in an indeterminate state, so fix this by simply setting the flags
before sending the request to the admin queue. Also changes the branding
string for i40evf to reduce confusion and to match up with our other
marketing materials.
Kamil adds a new variable defining admin send queue (ASQ) command write
back timeout to allow for dynamic modification of this timeout.
Anjali fix a bug in the flow director filter replay logic, so that we
call a replay after a sideband reset correctly.
Jesse adds code to initialize all members of the context descriptor to
prevent possible stale data.
Christopher fixes i40e to prevent writing to reserved bits, since the
queue index is only 0-127.
Jacob removes the unneeded header export.h from the i40e PTP code.
Fixes ixgbe PTP code where the PPS signal was not correct, as it
generates a one half HZ clock signal, it only generates one level
change per second. To generate a full clock, we need two level changes
per second.
Todd provides a fix for igb to bring up link when the PHY has powered
up, which was reported by Jeff Westfahl.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This limitation maybe had some reason in the past, but now there is not
one -> removing this.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Veaceslav Falico <vfalico@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rip out a bunch of redundant PCI-E Memory Window Read/Write routines,
collapse the more general purpose routines into a single routine
thereby eliminating the need for a large stack frame (and extra data
copying) in the outer routine, change everything to use the improved
routine t4_memory_rw.
Based on origninal work by Casey Leedom <leedom@chelsio.com> and
Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the firmware interface to get the BAR0 value since we really don't want
to use the PCI-E Configuration Space Backdoor access which is owned by the
firmware.
Set up PCI-E Memory Window registers using the true values programmed into
BAR registers. When the PF4 "Master Function" is exported to a Virtual
Machine, the values returned by pci_resource_start() will be for the
synthetic PCI-E Configuration Space and not the real addresses. But we need
to program the PCI-E Memory Window address decoders with the real addresses
that we're going to be using in order to have accesses through the Memory
Windows work.
Based on origninal work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change logic which determines our Physical Function at PCI Probe time.
Now we read the PL_WHOAMI register and get the Physical Function.
Pass Physical Function to Upper Layer Drivers in lld_info structure in the
new field "pf" added to lld_info. This is useful for the cases where the
PF, say PF4, is attached to a Virtual Machine via some form of "PCI
Pass Through" technology and the PCI Function shows up as PF0 in the VM.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For consistency, use the ptp_find_pin function to get the calibration pin,
not gpio_tab.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This constraints the pin assignment to not allow the calibration function to
be reassigned and only allow reassigning the calibratin pin if only one phy is
connected.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch increases the number of supported periodic output pins from
1 to 7. The last pin is reserved for sync.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Periodic output triggers 0 and 1 of the dp83640 has a programmable
duty-cycle which is controlled by the Pulsewidth2 field of the trigger
data register. This field is not documented in the datasheet, but it
is described in the "PHYTER Software Development Guide" section
3.1.4.1. Failing to set the field can result in unstable/no trigger
output.
Add programming of the Pulsewidth2 field, setting it to the same value
as the Pulsewidth field for a 50% duty cycle.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware will provide this information as soon as we will start
processing incoming packets, so there is no need to set the RX buffer
length during buffer allocation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use the PHY library which will determine the link state for us, make
sure we start with a carrier off until libphy has completed the link
training.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as register_netdev() is called, the network device notifiers are
running which means that other parts of the kernel, or user-space
programs can call the network device ndo_open() callback and use the
interface.
Disable the Ethernet device clock before we register the network device
such that we do not create the following situation:
CPU0 CPU1
register_netdev()
bcmgenet_open()
clk_prepare_enable()
clk_disable_unprepare()
and leave the hardware block gated off, while we think it should be
gated on.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although we do not limit the number of packets the TX completion
function bcm_sysport_tx_reclaim() is allowed to reclaim, we were still
using its return value as-is. This means that we could hit the WARN() in
net/core/dev.c where work_done >= budget.
Make sure we do exit the NAPI context when the TX ring is empty, and
pretend there was no work to do.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UniMAC CMD_SW_RESET bit is not a self-clearing bit, so we need to
assert it, wait a bit and clear it manually. As a result, umac_reset()
is updated not to return any value. The previous version of the code
simply wrote 0 to the CMD register, which would make the busy-waiting
loop exit immediately, having zero effect.
By writing 0 to the CMD register, we were clearing all bits in the CMD
register, and not using the hardware reset default values which are
set on purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT Ethernet MAC supports multicast just fine, it just lacks
any sort of Unicast/Broadcast/Multicasting filtering at the Ethernet MAC
level since that is handled by the front end Ethernet switch, but that
is properly handled by bcm_sysport_set_rx_mode().
Some user-space applications might be relying on the presence of this
flag to prevent using multicast sockets, this also prevents that
interface from joining the IPv6 all-router mcast group.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are linux distributions where the inbox bnx2x driver contains SRIOV
support but doesn't contain the changes introduced in b9871bcf
"bnx2x: VF RSS support - PF side".
A VF in a VM running that distribution over a new hypervisor will access
incorrect addresses when trying to transmit packets, causing an attention
in the hypervisor and making that VF inactive until FLRed.
The driver in the VM has to ne upgraded [no real way to overcome this], but
due to the HW attention currently arising upgrading the driver in the VM
would not suffice [since the VF needs also be FLRed if the previous driver
was already loaded].
This patch causes the PF to fail the acquire message from a VF running an
old problematic driver; The VF will then gracefully fail it's probe preventing
the HW attention [and allow clean upgrade of driver in VM].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This improves the performance of driver on machine with L1_CACHE_SHIFT of at
most 32 bytes [HW was planned for 64-byte aligned fastpath data].
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now VFs were oblvious to the actual configured link parameters.
This patch does 2 things:
1. It enables a PF to inform its VF using the bulletin board of the link
configured, and allows the VF to present that information.
2. It adds support of `ndo_set_vf_link_state', allowing the hypervisor
to set the VF link state.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While it is legal to kfree(NULL), it is not wise to use :
put_page(virt_to_head_page(NULL))
BUG: unable to handle kernel paging request at ffffeba400000000
IP: [<ffffffffc01f5928>] virt_to_head_page+0x36/0x44 [bnx2x]
Reported-by: Michel Lespinasse <walken@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Fixes: d46d132cc0 ("bnx2x: use netdev_alloc_frag()")
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds some cores with 0x2057 radio which will be supported soon as
well as core 40 that I missed in the earlier firmware patch.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It doesn't include any device (radio revision) specific code yet, so it
isn't really usable. As the commit says, it's just some generic code.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are several exit path from the PCI probe function.
Some of them, that are taken in case of errors, forget to set the "err"
variable, that is returned by the probe function.
This can lead to the kernel thinking the probe function succeeds while it
didn't, and this in turn causes extra calls to the "remove" function.
This patch fix this problem by ensuring "err" variable is assigned to a proper
non-zero value in each exit path.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All boards supported by this driver could work using PIO or MMIO for accessing
registers.
This driver tries to access HW by using MMIO, and, if this fails for somewhat
reason, the driver tries to fall back to PIO mode.
MMIO-mode is straightforward on all boards.
PIO-mode is straightforward on rtl8180 only.
On rtl8185 and rtl8187se boards not all registers are directly available in PIO
mode (they are paged).
On rtl8185 there are two pages and it is known how to switch page.
PIO mode works, except for only one access to a register out of default page,
recently added by me in the initialization code with patch:
rtl818x_pci: Fix rtl8185 excessive IFS after CTS-to-self
This can be easily fixed to work in both cases (MMIO and PIO).
On rtl8187se, for a number of reasons, there is much more work to do to fix PIO
access.
PIO access is currently broken on rtl8187se, and it never worked.
This patch fixes the said register write for rtl8185 and makes the driver to
fail cleanly if PIO mode is attempted with rtl8187se boards.
While doing this, I converted also a couple of printk(KERN_ERR) to dev_err(), in
order to make checkpatch happy.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the driver configures mac80211 to provide two rates for each TX frame:
One initial rate and one alternate fallback rate, each one with its retry count.
HW does not support fully this: rtl8180 doesn't have support for rate scaling at
all, and rtl8185/rtl8187SE supports it in a way that does not fit with mac80211:
The HW does automatically fall back to the next lower rate, and only a lower
limit can be specified, so the HW may TX also on rates in between the two rates
specified by mac80211. Furthermore only the total TX retry count can be
specified for each packet, while the number of TX attempts before scaling rate
can be configured only globally (not per each packet).
Currently the driver sets the HW auto rate fallback mechanism to quickly scale
rate after a couple of retries, and it uses the alternate rate requested by
mac80211 as fallback limit rate (and it does this even wrongly).
The HW indeed will behave differently than what mac80211 mandates, that is
probably undesirable, and the reported TX retry count may not refer to what
mac80211 thinks, and this could fool mac80211.
This patch makes the driver to declare to mac80211 to support only one rate
configuration for each packet, and it does disable the HW auto rate fallback
mechanism, relying only on SW and letting mac80211 to do all by itself.
This should ensure correct operation and fairness respect to mac80211.
Indeed here tests with iperf do not show significant performance differences.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
HW is programmed with wrong retry count value for TX:
Mac80211 passes to driver the number of times the TX should be attempted.
The HW, instead, wants the number of time the TX should be retried if it fails
the first time (assuming we have to TX it at least one time).
This patch correct this.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rtl8187se support has been added to the rtl818x_pci driver by extracting a lot
of information from a rtl8187se Linux staging driver included in the kernel at
the time rtl8187se support was added.
The rtl818x_pci main file has a comment that advertises this.
Recently this staging driver has been removed from the kernel, but I still feel
it can be useful as "reference" code (in case of bugs, or to implement
improvements in rtl818x_pci driver).
This one-line patch adds a comment in rtl818x_pci driver to point people
searching for that "reference code" to the last kernel version still containing
it (3.14).
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Measuring time between _end_ of CTS-to-self and _end_ of datapacket (with a
prism54 board and mac80211 hacked to let the MAC timestamp stay untouched in the
radiotap header) resulted in about 300uS, while the datapacket itself should be
by far shorter (less than 100uS) and IFS should be SIFS (10uS).
This measure was confirmed whith a scope: about 250uS IFS has been seen between
the two packets.
This situation causes the CTS-to-self protection mechanism to work incorrectly
due to the NAV expiring during, or even before beginning, the packet
transmission, and it also causes the performances to be anyway reduced due to
time waste.
This problem has been seen at every packet TXed with CTS-to-self enabled on
rtl8185 board.
rtl8187se seems not affected (and rtl8180, being a 802.11b card, does not have
CTS-to-self mechaninsm).
This patch fixes this by adding a magic register write, making the board wait
for correct SIFS after CTS-to-self packet.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BSSID register was written with six byte-writes.
It seems that, similarly to what happens with MAC registers, they needs to be
written with one 16-bit and one 32-bit writes, otherwise the write does not work.
The byte write didn't work only on my rtl8185, while it worked on rtl8180 and
rtl8187se, BTW since there are probably a number of different ASIC revisions out
of there, I let the change to affect all cards.
It shouldn't hurt anyway.
Signed-off-by: Andrea Merello <andrea.merello@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LCNXN is simply a continuation of N, e.g. code handling LCNXN revs 0 and
1 is mostly the same as for N-PHY revs 7+.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix checkpatch warning:
WARNING: kfree(NULL) is safe this check is probably not required
Cc: Stanislav Yakovlev <stas.yakovlev@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes a couple of issues:
- absence of deallocation of rsi_dev->rx_usb_urb[0] in the driver;
- potential NULL pointer dereference because of lack of checks for memory
allocation success in rsi_init_usb_interface().
By the way, it makes rsi_probe() returning error code instead of 1
and fixes comments regarding returning values.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Right now sleep duration is configured as beacon interval. It should be
the multiple of beacon interval by listen period which helps to
reduce station power consumption.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier the listen interval is used to decide switching between
operating and off-channels during bgscan and to improve throughput,
the listen interval is reduced to 1. After optimiztion in scan
state machine, listen period is not used for decision making and
hence reverting it back to original value.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The beacon configurations are not cached properly after the station
associates with AP. Not handling BEACON_INFO, is failing to update
dtim period and also it is causing below warning message.
WARNING: CPU: 1 PID: 0 at drivers/net/wireless/ath/ath9k/recv.c:548
ath_rx_tasklet+0xc89/0xca0 [ath9k]()
Call Trace:
[<c14669c9>] dump_stack+0x48/0x69
[<c104f1a2>] warn_slowpath_common+0x82/0xa0
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
[<fd38c2f9>] ? ath_rx_tasklet+0xc89/0xca0 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Treat frames that underwent a CCK or OFDM restart as frames with an invalid CRC.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the FIF_FCSFAIL filter flag is set, pass frames with CRC errors.
Signed-off-by: Mathy Vanhoef <vanhoefm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PPS signal is not correct, as it generates a one half HZ clock
signal, as it only generates one level change per second. To generate a
full clock, we need two level changes per second. Also, change the name
of the #define, in order to prevent confusion between it and
NSEC_PER_SEC which is not guaranteed to be a 64bit value.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Call igb_setup_link() when the PHY is powered up.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Reported-by: Jeff Westfahl <jeff.westfahl@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a slash to the branding string to reduce confusion and match up with
our other marketing materials.
Change-ID: I8229e8c3e43083b7a29c859a250f8d2d4dc46b9e
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need the export.h header so we can just go ahead and remove it.
Change-ID: I9057396b141ee449d8299409081358b9270a7c4d
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Prevent writing to reserved bits, queue index is 0-127
Change-ID: Ic923e1c92012a265983414acd8f547c4bdac2e34
Signed-off-by: Christopher Pau <christopher.pau@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver needs to initialize all members of context descriptor. Stale
data is possible otherwise.
Change-ID: Idc6b53af45583509da42d5ec0824cbaf78aee64f
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With the auto_disable flags added there was a bug that was causing the
replay logic to not work correctly.
This patch fixes the issue so that we call a replay after a sideband
reset correctly.
Change-ID: I005fe1ac361188ee5b19517a83c922038cba1b00
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new variable defining ASQ command write back timeout to allow for
dynamic modification of this timeout. Initialize it on AQ initialize
routine with default value, vary it on device ID.
Change-ID: I5c9908f9d7c5455634353b694a986d6f146d1b9d
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In some circumstances, the firmware could beat us to the punch, and the
reply from the PF would come back before we were able to properly modify
the aq_pending and aq_required flags. This would mess up the flags and
put the driver in an indeterminate state, much like Schrödinger's cat.
However, unlike the cat, the driver is definitely dead.
To fix this, simply set the flags before sending the request to the AQ.
This way, it won't matter if the interrupt comes back too soon.
Change-ID: I9784655e475675ebcb3140cc7f36f4a96aaadce5
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Make mask value of all 1s. Value of -1 can't be used for u32 type.
Change-ID: I49d58b77639939fe7447a229dbf1f4a1bf7419ce
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Per a recent HW designer comment, this code is for ripping through the
queues and interrupts to fully disable them on driver init, specifically
to help clean up after a PXE or other early boot activity.
Change-ID: I32ed452021a1c2b06dace1969976f882a37b9741
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Clear the AQ BAH and BAL registers on a clean shutdown to help make sure
all is tidy when the driver is done.
Change-ID: I393e92680247daa52a8e00bab183213672d73578
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the Base Address High and Low to the admin queue struct to simplify
another bit of "which context" logic in the config routines.
Change-ID: Iae195a7da3baffc1a9d522119e1e2b427068ad07
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-26
This series contains updates to i40e and i40evf.
Kamil provides a cleanup patch to i40e where we do not need to acquire the
NVM for shadow RAM checksum calculation, since we only read the shadow RAM
through SRCTL register.
Paul provides a fix for handling HMC for big endian architectures for i40e
and i40evf.
Mitch provides four cleanup and fixes for i40evf. Fix an issue where if
the VF driver fails to complete early init, then rmmod can cause a softlock
when the driver tries to stop a watchdog timer that never got initialized.
So add a check to see if the timer is actually initialized before stopping
it. Make the function i40evf_send_api_ver() return more useful information,
instead of just returning -EIO by propagating firmware errors back to the
caller and log a message if the PF sends an invalid reply. Fix up a log
message that was missing a word, which makes the log message more readable.
Fix an initialization failure if many VFs are instantiated at the same time
and the VF module is autoloaded by simply resending firmware request if
there is no response the first time.
Jacob does a rename of the function i40e_ptp_enable() to
i40e_ptp_feature_enable(), like he did for ixgbe, to reduce possible
confusion and ambugity in the purpose of the function. Does follow on
PTP work on i40e, like he did for ixgbe, by breaking the PTP hardware
control from the ioctl command for timestamping mode. By doing this,
we can maintain state about the 1588 timestamping mode and properly
re-enable to the last known mode during a re-initialization of 1588 bits.
Anjali cleans up the i40e driver where TCP-IPv4 filters were being added
twice, which seems to be left over from when we had to add two PTYPEs for
one filter. Fixes the flow director sideband logic to detect when there
is a full flow director table. Also fixes the programming of FDIR where
a couple of fields in the descriptor setup that were not being
programmed, which left the opportunity for stale data to be pushed as
part of the descriptor next time it was used.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
MSI-X should use PCI_MSIX_FLAGS not PCI_MSI_FLAGS.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Checkpatch issued a warning preferring to use kstrto<type> when
using a single variable sscanf. Change the sscanf invocation to
a kstrtouint call.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the driver makes use of the additional mac address
registers in the hardware to provide perfect filtering. The
hardware can also have a set of hash table registers that can
be used for imperfect filtering. By using imperfect filtering
the additional mac address registers can be used for layer 2
filtering support. Use the hash table registers if the device
has them.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for (imperfect) filtering of
VLAN tag ids using a 16-bit filter hash table. When
VLANs are added, a 4-bit hash is calculated with the
result indicating the bit in the hash table to set.
This table is used by the hardware to drop packets with
a VLAN id that does not hash to a set bit in the table.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When receiving a VLAN packet check to be sure that VLAN
RX CTAG stripping is enabled before indicating that the
tag has been stripped in the packet information data
structure.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC_VLAN_Incl register (0x0060) must be set to indicate
that the VLAN tag to be inserted comes from a Tx context
descriptor and not the MAC_VLAN_Incl register. Also, even
though it is the default, explicitly set the type of tag to
be inserted as a CTAG.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid conflicts with other include files, add
a prefix to the defines in xgbe.h.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a couple of fields in the fdir descriptor setup that
were not being reprogrammed, which left the opportunity for stale
data to be pushed as part of the descriptor next time it was used.
Change-ID: Ieee5c96a7d4713d469693f086c4854de949a7633
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
"fd current cnt" can be used to print the total filters consumed
by this interface, this includes guaranteed and best effort filters.
Change-ID: I2c417810c4999ce1388d2ea26f8e69679ba33966
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hardware does not have a way of telling a PF how much of the global
shared FD table space is still available or is consumed.
Previously, every PF but PF0 would think there was still space available
when there wasn't. The PFs would continue to try to add filters and fail.
With this new logic if a filter programming error is detected we just
check if we are close to the guaranteed space full and that can be used
as a hint to say, there might not be space and we should turn off the
features. This way we can turn off the feature in SW for all PFs in
time.
Change-ID: I725cb2fab16c033f883056362b4542c1400503c5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There wasn't a need to play the logic twice, it seems
like a left over from when we had to add two PTYPEs for
one filter. There should be no change in the number of
filters that actually got added to the hardware.
Change-ID: I5071d02eafd020b60e30eb96219f110f334eec85
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently every time we run through the i40e_ptp_init routine, we create
a new device node. This function is called by i40e_reset_and_rebuild
which is used to handle reset of the device. Even though the 1588
registers only get cleared on a GLOBAL reset, this function is still
called to handle a CORE reset.
This causes a leak of PTP device nodes at every reset. To fix this,
break PTP device clock node creation out of i40e_ptp_init, and only call
this if we don't already have a device created. Further invocation of
i40e_ptp_init will not generate new PTP devices. Instead, only the
necessary work required to reconfigure 1588 will be done.
This change also fixes an issue where a reset can cause the
device to forget it's timestamp configuration, and revert to the default
mode.
Change-ID: I741d01c61d9fe1d24887859d1316e1a8a892909e
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch prevents the SIOCGHWTSTAMP ioctl from possibly returning bad
data, by not permanently storing the setting into the private
structure until after we've finished validating that we can support it.
Change-ID: Ib59f9b4f73f451d5a2e76fb8efa5d4271b218433
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch facilitates future work by breaking the PTP hardware control
bits out of the i40e_set_ts_config function. By doing this, we can
maintain state about the 1588 timestamping mode and properly re-enable
to the last known mode during a re-initialize of 1588 bits.
This patch also modifies i40e_ptp_init to call the
i40e_ptp_set_timestamp_mode during the reconfiguration process. A
future patch will ensure that the hwtstamp_config structure is not reset
during this process, so that timestamp mode will be maintained across a
reset.
Change-ID: Ic20832c96c5c512ac203b6c7534e10d891c560f0
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Reduces possible confusion and ambiguity in purpose of the ancillary
feature control entry point function.
Change-ID: I21d773c1a86878f6d061505185b596c788d1b7cc
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Sometimes the firmware will not indicate an error but fail to pass a
message between the VF and the PF driver. If this happens, just resend
the request.
This fixes an initialization failure if many VFs are instantiated at the
same time and the VF module is autoloaded.
Change-ID: Idd1ad8da2fd5137859244685c355941427d317d7
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Correct a missing word in a log message.
Change-ID: Id94da7d9f842382d073b3947e0b616503e2f8e91
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When verifying the API version (which is the first time the driver
communicates with the firmware and thus the PF driver), there are many
ways in which a failure can occur. There may be an error from the
firmware, there may be unresponsive firmware, there may be an error from
the PF driver, etc, etc.
Make this function return more useful information, instead of just -EIO.
Propagate FW errors back to the caller, and log a message if the PF
sends an invalid reply.
Change-ID: I3e9135a2b80f7acdb855f62f12b2b2668c9a8951
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the VF driver fails to complete early init, then rmmod can cause a
softlock when the driver tries to stop a watchdog timer that never even
got initialized.
Add a check to see if the timer is actually initialized before stopping
it.
Change-ID: Id9d550aa8838e07f4b02afe7bc017ef983779efc
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix HMC handling for big endian architectures.
Change-ID: Id8c46fc341815d47bfe0af8b819f0ab9a1e9e515
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We do not need to acquire NVM for Shadow RAM XSUM calculation, as we only
read from SR through SRCTL register for which having the ownership is not
required.
Change-ID: Ie238a8f09917d1d25f24cc7cec271951ac7b98f2
Signed-off-by: Kamil Krawczyk <kamil.krawczyk@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If CONFIG_RFS_ACCEL=n:
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_open':
drivers/net/ethernet/cisco/enic/enic_main.c:1603:2: error: implicit declaration of function 'enic_rfs_flw_tbl_init' [-Werror=implicit-function-declaration]
drivers/net/ethernet/cisco/enic/enic_main.c: In function 'enic_stop':
drivers/net/ethernet/cisco/enic/enic_main.c:1630:2: error: implicit declaration of function 'enic_rfs_flw_tbl_free' [-Werror=implicit-function-declaration]
Introduced in commit a145df23ef ("enic: Add
Accelerated RFS support").
Dummy functions are provided, but their prototypes are missing, causing the
build failure. Provide dummy static inline functions instead to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-24
This series contains updates to i40e and i40evf.
Greg provides a patch to stop the VF device after setting its MAC address.
This is due to if the host VMM administrator has changed the VF device's MAC
address then the i40e driver needs to halt the VF device so that the
administrator will be forced to reload the VF driver so that the VF driver
will start using the newly assigned MAC address.
Shannon provides several patches for i40e, first makes prep_for_test() a
void function since the return value was being ignored for the most part
by all its callers. Adds a log warning when the firmware's API minor/major
number is not what we expect to assist the user by informing them they
may need to update their NVM or SW. Cleans up a stray print message
so that it is similar to other print messages. Ensures to set the
WoL flag when setting LAA and allow the user to set LAA again. So do
not short-circuit the LAA assignment when the driver thinks it has
already been done as it is possible that the user might want to force
the address setting again. Provides a couple more LAA fixes to ensure
the LAA gets restored after resets.
Neerav provides a patch for i40e to add a PF reset when a malicious driver
event for the PF occurs. As per the specification when the PF driver
receives a malicious driver event the queue that caused the event is
already stopped and it is expected that the function that owns the queue
will reset the queue, but in some cases it may not be possible to determine
the queue, so it is suggested to reset the whole function.
Carolyn fixes ethtool coalesce settings to allow 0 as a disable value and
adds message to user about invalid values.
Jesse removes a reserved type which was not removed from the code.
Catherine provides a patch to add the ability to enable/disable link from
set_link)restart_an() which will make it easy to toggle link without
calling set_phy_config() when no other link settings need to change.
Anjali provides a patch to ensure we do a PF reset on Tx hang and that
way we avoid any Malicious Driver Detect (MDD) events because of a Tx
queue disable failure.
v2:
- fixed the un-needed return in patch 2 based on feedback from Sergei Shtylyov
- added punctuation to print statements and code comment based on
feedback from Sergei Shtylyov
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is trivial to add netpoll support to veth, since
it is not a stacked device, we don't need to setup and
clean up netpoll.
Reported-by: Stefan Priebe <s.priebe@profihost.ag>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the mdio probe function fails in emac_open, the interrupt we just requested
isn't freed. If emac_open is called again, for example because we try to set up
the interface again, the kernel will oops because the interrupt wasn't properly
released.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.11+
Signed-off-by: David S. Miller <davem@davemloft.net>
o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands cnic driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>
o QLogic has acquired the NetXtremeII products and drivers from Broadcom.
This patch re-brands bnx2 driver as a QLogic driver
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3f85944fe2 ("net: Add sysfs file
for port number") introduce dev_port to network devices. cxgb4 adapters
have multiple ports on the same PCI function, and used dev_id to
identify those ports. That use was removed by commit
8c367fcbe6 ("cxgb4: Do not set
net_device::dev_id to VI index"), since dev_id should be used only when
devices share the same MAC address.
Using dev_port for cxgb4 allows different ports on the same PCI function
to be identified.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original code uses netdev->real_num_tx_queues to bookkeep number of
queues and invokes netif_set_real_num_tx_queues to set the number of
queues. However, netif_set_real_num_tx_queues doesn't allow
real_num_tx_queues to be smaller than 1, which means setting the number
to 0 will not work and real_num_tx_queues is untouched.
This is bogus when xenvif_free is invoked before any number of queues is
allocated. That function needs to iterate through all queues to free
resources. Using the wrong number of queues results in NULL pointer
dereference.
So we bookkeep the number of queues in xen-netback to solve this
problem. This fixes a regression introduced by multiqueue patchset in
3.16-rc1.
There's another bug in original code that the real number of RX queues
is never set. In current Xen multiqueue design, the number of TX queues
and RX queues are in fact the same. We need to set the numbers of TX and
RX queues to the same value.
Also remove xenvif_select_queue and leave queue selection to core
driver, as suggested by David Miller.
Reported-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
CC: Ian Campbell <ian.campbell@citrix.com>
CC: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 506724c463 "tg3: Override clock,
link aware and link idle mode during NVRAM dump" changed the timeout
value for nvram command execution from 100ms to 1ms. But the 1ms
timeout value was only sufficient for nvram read operations but not
write operations for most of the devices supported by tg3 driver.
This patch sets the MAX to 50ms. Also it uses usleep_range instead
of udelay.
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Why is converting time formats so desired if there are proper
interfaces for this?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Bing Zhao <bzhao@marvell.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit a82fc3b4a2bceb7c6587249cb690342eb5065979.
Thomas corrected me on that I misunderstood Johannes' comment
for net_timedelta() and the ktime_get_real() usage inside
__net_timestamp().
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed a warning related to incorrect return type and removed an
unnecessary semi colon.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixed a potential buffer overflow in 'rsi_rates' and a sparse warning
related to difference in endianness in rsi_91x_mgmt.c.
Signed-off-by: Jahnavi Meher <jahnavi.meher@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The p54 driver uses request_firmware() twice, once for actual
firmware and then another time for an optional user overide on
EEPROM, 3826.eeprom. The custom EEPROM is optional but if not
present we'll introduce an extra lag of 60 seconds with udev
present. Annotate we don't want udev nonsense here to avoid
the lag in case its not present.
This was found with the following SmPL patch.
@ firmware_not_critical @
expression cf;
expression config_file;
expression dev;
int ret;
identifier l;
statement S;
@@
- ret = request_firmware(&cf, config_file, dev);
+ ret = request_firmware_direct(&cf, config_file, dev);
if (ret < 0) {
... when != goto l;
when != return ret;
when any
} else {
...
release_firmware(cf);
...
}
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: linux-wireless@vger.kernel.org
Cc: cocci@systeme.lip6.fr
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Acked-By: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix tx gain table index on fast channel change for AR953x.
Signed-off-by: Rajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Clean ucode selection, fix choice of firmware for LCN, drop some goto-s,
add new devices.
Tested on 14e4:4312, 14e4:4315, 14e4:4328, 14e4:432b, 14e4:4353.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For consistency with other drivers, replace a magic number by a macro.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
bt_msr & 0xfc will never match 0x3. Fix this by using a mask that actually matches the available types.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add support for external PA and clean code a bit.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
