This corrects the example by adding #address-cells, #size-cells and a reg for
each trigger to comply to the ePAPR, as suggested by Mark Rutland in
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-February/234184.html
Also, it removes the properties that are not used anymore, to stop propagating
them.
Also fixes atmel,adc-use-external-triggers property name.
Finally, fixes a few typos.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Looking at the current vendor strings used in the kernel's .dts/.dtsi
files, some vendors are used a high number of times without
being documented. Document the ones that are used more than 10 times.
Note: a few inconsistencies were found, and thus not documented.
Here is the list:
- mrvl: duplicates "marvell"
- st-ericsson: duplicates "ste" _and_ "stericsson"
- pci8086: seems to be a unfortunate alias for "intel"
- pnpPNP: used on PowerPC?
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a vendor prefix for Standard Microsystems Corporation, now part of
Microchip.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Merge the request/release callbacks which are in a separate branch for
consumption by the gpio folks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
atmel,at91sam9rl-udc is a USB gadget, it has no means to control vbus.
atmel,vbus-gpio is in fact used to detect the presence of vbus.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
[nicolas.ferre@atmel.com: modify the commit message]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
This adds the ability to set "clock-frequency" in the device tree for the at91
i2cbus following the naming of other i2c bus implementations. If the property
is not set,the clock frequency will default to the previously used define
of 100KHz.
Signed-off-by: Marek Roszko <mark.roszko@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
This patch provides bindings for the 64-bit timer in the KeyStone
architecture devices. The timer can be configured as a general-purpose 64-bit
timer, dual general-purpose 32-bit timers. When configured as dual 32-bit
timers, each half can operate in conjunction (chain mode) or independently
(unchained mode) of each other.
It is global timer is a free running up-counter and can generate interrupt
when the counter reaches preset counter values.
Documentation:
http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the timer driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
in the dts files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=g3T0
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.15, part 2" from Tony Lindgren:
Part two of omap device tree changes enabling driver features
in the dts files.
* tag 'omap-for-v3.15/dt-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-evmsk: enable dual_emac mode
ARM: dts: DRA7: Add device nodes for ABB
ARM: dts: OMAP4: Add device nodes for ABB
ARM: dts: OMAP36xx: Add device node for ABB
ARM: dts: am43x-epos-evm: add SD card hotplug support
ARM: dts: am335x-evm: add SD card hotplug support
ARM: dts: am437x gp-evm: add sd card dt nodes
ARM: dts: omap5: added dt properties to adapt to the new phy framwork
ARM: OMAP2+: Use pdata quirks for wl12xx on the AM335x EV-MSK
ARM: dts: Update echi-omap DT binding example usage
ARM: dts: Get rid of incompatible ids for hci-omap USB host nodes
ARM: OMAP2+: Remove legacy_init_ehci_clk()
ARM: dts: Add support for OMAP4 Gumstix DuoVero/Parlor
Signed-off-by: Olof Johansson <olof@lixom.net>
- add BCM5301x support
- remove GENERIC_TIME
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WKwJ
-----END PGP SIGNATURE-----
Merge tag 'armsoc/for-3.15/soc-2' of git://github.com/broadcom/mach-bcm into next/soc
Merge "ARM: mach-bcm soc updates" from Matt Porter:
- add BCM5301x support
- remove GENERIC_TIME
* tag 'armsoc/for-3.15/soc-2' of git://github.com/broadcom/mach-bcm:
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
Signed-off-by: Olof Johansson <olof@lixom.net>
Add device tree binding for ImgTec Consumer Infrared block, specifically
major revision 1 of the hardware.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This patch adds missing #gpio-cells and also adds a
usage example for leds.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds soft reset controller support for STiH415 and adds new
softreset lines required for other device tree nodes in the header file.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
This patch adds a reset controller node to the SOC device tree and also
adds new header files with reset lines required for other device tree
nodes.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
It's not implemented in the driver, so it's a bad example.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some flashes can only be properly accessed when the ECC mode is
specified, so a way to describe such mode is required.
Together, the ECC strength and step size define the correction capability,
so that we say we will correct "{strength} bit errors per {size} bytes".
The interpretation of these parameters is implementation-defined, but they
often have ramifications on the formation, interpretation, and placement of
correction metadata on the flash. Not all implementations must support all
possible combinations. Implementations are encouraged to further define the
value(s) they support.
Acked-by: Boris BREZILLON <b.brezillon.dev@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Describe the properies used by the trf7970a
RFID/NFC/15693 transceiver driver.
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Introduce "altr,socfpga-dw-mshc" to enable Altera's SOCFPGA platform
specific implementation of the dw_mmc driver.
Also add the "syscon" binding to the "altr,sys-mgr" node. The clock
driver can use the syscon driver to toggle the register for the SD/MMC
clock phase shift settings.
Finally, fix an indentation error for the sysmgr node.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Chris Ball <chris@printf.net>
A collection of fixes for ARM platforms. A little large due to us missing to
do one last week, but there's nothing in particular here that is in itself
large and scary.
Mostly a handful of smaller fixes all over the place. The majority is made
up of fixes for OMAP, but there are a few for others as well. In particular,
there was a decision to rename a binding for the Broadcom pinctrl block that
we need to go in before the final release since we then treat it as ABI.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=YBim
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from from Olof Johansson:
"A collection of fixes for ARM platforms. A little large due to us
missing to do one last week, but there's nothing in particular here
that is in itself large and scary.
Mostly a handful of smaller fixes all over the place. The majority is
made up of fixes for OMAP, but there are a few for others as well. In
particular, there was a decision to rename a binding for the Broadcom
pinctrl block that we need to go in before the final release since we
then treat it as ABI"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: omap3-gta04: Add ti,omap36xx to compatible property to avoid problems with booting
ARM: tegra: add LED options back into tegra_defconfig
ARM: dts: omap3-igep: fix boot fail due wrong compatible match
ARM: OMAP3: Fix pinctrl interrupts for core2
pinctrl: Rename Broadcom Capri pinctrl binding
pinctrl: refer to updated dt binding string.
Update dtsi with new pinctrl compatible string
ARM: OMAP: Kill warning in CPUIDLE code with !CONFIG_SMP
ARM: OMAP2+: Add support for thumb mode on DT booted N900
ARM: OMAP2+: clock: fix clkoutx2 with CLK_SET_RATE_PARENT
ARM: OMAP4: hwmod: Fix SOFTRESET logic for OMAP4
ARM: DRA7: hwmod data: correct the sysc data for spinlock
ARM: OMAP5: PRM: Fix reboot handling
ARM: sunxi: dt: Change the touchscreen compatibles
ARM: sun7i: dt: Fix interrupt trigger types
- Support suspend from ocram (DDR IO floating) for imx6 platforms
- Add cpuidle support for imx6sl
- Sparse warning fixes for imx6sl and vf610 clock code
- Remove PWM platform code
- Support ptp and rmii clock from pad
- Support WEIM CS GPR configuration
- Random cleanups and defconfig updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJTFq0LAAoJEFBXWFqHsHzOqk4IAKO5D6WPahaDhQohpNUToD/O
bF0Jqt8+hNpDSH5OSQMCi2M/T8OQIlYRJ6nlL5snZs7GVLXm32O9Rb3B5cSQ/Dts
erCByWZwMPnmhuKwMh59CPIJI3qxsKQ1G8qTLecu2q4RagCmxiTNzzlS7pkaCqFN
SMc+4uP12/TSvfGXNcs9XydI/dB3AI7KgnOAZSAT/ljguHyqSM/N1s3q2dFQ9+Zf
+IOZKxLadOzVe4ucc/lUvPogXi7aOSptD52AnZLzoxIqOxUMt8o7KX8bT0UT/688
QgtwiE7CwTS2czXmp9C8bQ5q8SgaLzJv4LjoHXuq8oqyWQ2jMPJkhjq2ZqCB2KM=
=kCKC
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/soc
i.MX SoC changes for 3.15 from Shawn Guo:
- Support suspend from ocram (DDR IO floating) for imx6 platforms
- Add cpuidle support for imx6sl
- Sparse warning fixes for imx6sl and vf610 clock code
- Remove PWM platform code
- Support ptp and rmii clock from pad
- Support WEIM CS GPR configuration
- Random cleanups and defconfig updates
* tag 'imx-soc-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (373 commits)
ARM: imx6: drop .text.head section annotation from headsmp.S
ARM: imx6: build suspend-imx6.o with CONFIG_SOC_IMX6
ARM: imx6: rename pm-imx6q.c to pm-imx6.c
ARM: imx6: introduce CONFIG_SOC_IMX6 for i.MX6 common stuff
ARM: imx6: do not call imx6q_suspend_init() with !CONFIG_SUSPEND
ARM: imx6: call suspend_set_ops() from suspend routine
ARM: imx6: build headsmp.o only on CONFIG_SMP
ARM: imx6: move v7_cpu_resume() into suspend-imx6.S
ARM i.MX6q: Mark VPU and IPU AXI transfers as cacheable, increase IPU priority
ARM: imx6q: Add GPR6 and GPR7 register definitions for iomuxc gpr
bus: imx-weim: support CS GPR configuration
ARM: mach-imx: Kconfig: Remove IMX_HAVE_PLATFORM_IMX2_WDT from SOC_IMX53
ARM: imx_v6_v7_defconfig: Select CONFIG_DEBUG_FS
ARM: mach-imx: Select CONFIG_SRAM at ARCH_MXC level
ARM: imx: add speed grading check for i.mx6 soc
ARM: imx: avoid calling clk APIs in idle thread which may cause schedule
ARM: imx6q: support ptp and rmii clock from pad
ARM: imx6q: remove unneeded clk lookups
ARM: imx_v6_v7_defconfig: Select CONFIG_MMC_UNSAFE_RESUME
ARM: imx_v4_v5_defconfig: Select CONFIG_MMC_UNSAFE_RESUME
...
Among them:
ARM: prima2: l2x0: fix checkpatch issues
ARM: prima2: platsmp: fix checkpatch issues
ARM: prima2: common: fix checkpatch issues
ARM: prima2: rtciobrg: fix the typo about license
ARM: prima2: staticize sirfsoc_init_late function
ARM: prima2: move to generic reset controller driver framework
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aN9r
-----END PGP SIGNATURE-----
Merge tag 'sirf-soc-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux into next/cleanup
ARM: sirf: machine update for 3.15 from Barry Song:
Most of the below are some minor fixes for coding style. "ARM: prima2:
move to generic reset controller driver framework" has been ready near
3.14 merge window, but it was late to merge in 3.14, so move this one
to 3.15.
* tag 'sirf-soc-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/baohua/linux:
ARM: prima2: move to generic reset controller driver framework
ARM: prima2: staticize sirfsoc_init_late function
ARM: prima2: rtciobrg: fix the typo about license
ARM: prima2: common: fix checkpatch issues
ARM: prima2: platsmp: fix checkpatch issues
ARM: prima2: l2x0: fix checkpatch issues
Signed-off-by: Olof Johansson <olof@lixom.net>
- use macros instead of hard coded numbers for clock bindings
NOTE: this is based on v3.15-next/dt-samsung
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4qfh
-----END PGP SIGNATURE-----
Merge tag 'exynos-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung exynos clock related DT updates for v3.15 from Kukjim Kim:
- use macros instead of hard coded numbers for clock bindings
NOTE: this is based on v3.15-next/dt-samsung
* tag 'exynos-clk' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: use macros in clock bindings for exynos5440
ARM: dts: use macros in clock bindings for exynos5420
ARM: dts: use macros in clock bindings for exynos5250
ARM: dts: use macros in clock bindings for exynos4
For exynos4412
- update vdd_arm voltage range for odroidx board
For exynos5250
- add PMU sysreg node and update watchdog node
- re-organize RTC status
- add max77686 pmic node for smdk5250
For exynos5420
- add PMU sysreg, i2s, adma and watchdog nodes
- re-organize RTC status
- add fixed voltage regulators and regulator nodes
for smdk5420
- add PMIC, GPIO based wake up key and vmmc-supply
support for arndale-octa board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=eUF9
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Samsung DT updates for v3.15 from Kukjin Kim:
For exynos4412
- update vdd_arm voltage range for odroidx board
For exynos5250
- add PMU sysreg node and update watchdog node
- re-organize RTC status
- add max77686 pmic node for smdk5250
For exynos5420
- add PMU sysreg, i2s, adma and watchdog nodes
- re-organize RTC status
- add fixed voltage regulators and regulator nodes
for smdk5420
- add PMIC, GPIO based wake up key and vmmc-supply
support for arndale-octa board
* tag 'samsung-dt' of http://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add vmmc-supply to MMC on arndale-octa board
ARM: dts: Add wake up key to arndale-octa board
ARM: dts: Add PMIC support to arndale-octa board
ARM: dts: Add fixed voltage regulators to smdk5420
ARM: dts: Add I2S nodes to exynos5420
ARM: dts: Add ADMA node to exynos5420
ARM: dts: Re-organize RTC status for exynos5250
ARM: dts: Re-organize RTC status for exynos5420
ARM: dts: Add regulator entries to smdk5420
ARM: dts: add max77686 pmic node for smdk5250
ARM: dts: update vdd_arm voltage range for exynos4412 based boards
ARM: dts: update watchdog device nodes for exynos5250 and exynos5420
ARM: dts: Add pmu sysreg node to exynos5250 and exynos5420
Signed-off-by: Olof Johansson <olof@lixom.net>
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=mpZ3
-----END PGP SIGNATURE-----
Merge tag 'for_3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next
Kishon writes:
Add new PHY drivers for SATA and USB in exynos, for USB in sunxi,
and a multi-purpose PHY in APM, all adapted to generic PHY framework.
Adapted USB3 PHY driver in OMAP to generic PHY driver and also used
the same driver for SATA in OMAP. It also includes miscellaneous cleanups
and fixes.
This patch allows to set independantly SCL and SDA falling times.
The tLOW period is computed by taking into account the SCL falling time.
The tHIGH period is computed by taking into account the SDA falling time.
For instance in case the margin on tLOW is considered too small, it can
be increased by increasing the SCL falling time which is by default set
at 300ns.
The same applies for tHIGH period with the help of SDA falling time.
Signed-off-by: Romain Baeriswyl <romainba@abilis.com>
Reviewed-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Shinya Kuribayashi <skuribay@pobox.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)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=MLEE
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/drivers
Merge OMAP crossbar support from Tony Lindgren:
Add support for GIC crossbar that routes interrupts on newer omaps.
Looks like people wanted these merged via the omap tree as it's
the only user for the GIC crossbar.
* tag 'omap-for-v3.15/crossbar-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: DRA: Enable Crossbar IP support for DRA7XX
ARM: OMAP4+: Correct Wakeup-gen code to use physical irq number
DRIVERS: IRQCHIP: CROSSBAR: Add support for Crossbar IP
DRIVERS: IRQCHIP: IRQ-GIC: Add support for routable irqs
Signed-off-by: Olof Johansson <olof@lixom.net>
* integrator/multiplatform-base:
ARM: integrator: select GPIO block
ARM: integrator: register the IM-PD1 VIC
ARM: integrator: use managed resources for the IM-PD1
irqchip: support cascaded VICs
irqchip: vic: update the base IRQ member correctly
clk: versatile: respect parent rate in ICST clock
clk: versatile: pass a parent to the ICST clock
ARM: integrator: switch to fetch clocks from device tree
ARM: SP804: make Integrator/CP timer pick clock from DT
ARM: integrator: define clocks in the device trees
Add support for Exynos 5250. This driver is to replace the old
USB 2.0 PHY driver.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Add a new driver for the Exynos USB 2.0 PHY. The new driver uses the generic
PHY framework. The driver includes support for the Exynos 4x10 and 4x12
SoC families.
Signed-off-by: Kamil Debski <k.debski@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AAie
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.15
another substantial pull request with new features all over
the place.
dwc3 got a bit closer towards hibernation support with after
a few patches re-factoring code to be reused for hibernation.
Also in dwc3 two new workarounds for known silicon bugs have
been implemented, some randconfig build errors have been fixed,
and it was taught about the new generic phy layer.
MUSB on AM335x now supports isochronous transfers thanks to
George Cherian's work.
The atmel_usba driver got two crash fixes: one when no endpoint
was specified in DeviceTree data and another when stopping the UDC
in DEBUG builds.
Function FS got a much needed fix to ffs_epfile_io() which was
copying too much data to userspace in some cases.
The printer gadget got a fix for a possible deadlock and plugged
a memory leak.
Ethernet drivers now use NAPI for RX which gives improved throughput.
Other than that, the usual miscelaneous fixes, cleanups, and
the like.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Russell writes:
This set of changes reorganises imx-drm's DT bindings by re-using the OF
graph parsing code which was located in drivers/media, removing the
temporary bindings.
The result is that more TODO entries are now removed. While we're not
quite done with this yet as there's a few straggling updates to imx-ldb
to come, but leaving these out is not detrimental at this point in time
- they are more an enhancement.
However, this pull has the additional complication that we're sharing
seven commits with Mauro's V4L git tree, which move the OF graph parsing
code out of drivers/media into drivers/of. Philipp's imx-drm changes
depend on these and my previously committed round of imx-drm commits.
Hence, the diffstat below is from a test merge with your tree head
(17b02809cf).
Mauro merged those seven commits earlier today as a git pull, so both
trees will be sharing exactly the same commit IDs.
I've given these changes a spin here on both my Hummingboard and Cubox-i4
(one is iMX6Solo, the other is iMX6Quad based), which includes Xorg using
the DRM device directly, and I find nothing wrong.
The diffstat does look a little scarey - this is because we're having to
update the ARM DT files along with this change, and obviously the
dependency on the OF graph parsing code.
This patch adds device tree binding documentation for the HDMI transmitter
on i.MX6.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch updates the device tree binding documentation for i.MX IPU/display
nodes using the OF graph bindings documented in
Documentation/devicetree/bindings/media/video-interfaces.txt.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SATA PHY needs a new compatible ID. Add it to the DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add wakeup, system and reference clocks to DT binding documentation.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The dra7-usb2 and am437-usb2 bindings have not yet been used.
Change them to be more elegant.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The compatible string doesn't have an x in it. Fix it. Also
remove the "qcom" prefix from pins and functions as this binding
uses the generic pinctrl bindings for the pins and functions.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
New driver
* Xilinx XADC driver - This has been ready for a while but was awaiting
a device tree ack (or as it turns out 3+ weeks).
Cleanup
* Drop some unreachable code from mag3110 highlighted by smatch.
Fix
* vf610 - introduced this cycle - put a possible negative error code
into an unsigned long. Another smatch find - this one promoted by
guilt that Dan was busy fixing all our messups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=OSqU
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.15c' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Third IIO new drivers and cleanups series for 3.15.
New driver
* Xilinx XADC driver - This has been ready for a while but was awaiting
a device tree ack (or as it turns out 3+ weeks).
Cleanup
* Drop some unreachable code from mag3110 highlighted by smatch.
Fix
* vf610 - introduced this cycle - put a possible negative error code
into an unsigned long. Another smatch find - this one promoted by
guilt that Dan was busy fixing all our messups.
Those are defined by the common PCI binding.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The device tree graph bindings as used by V4L2 and documented in
Documentation/device-tree/bindings/media/video-interfaces.txt contain
generic parts that are not media specific but could be useful for any
subsystem with data flow between multiple devices. This document
describes the generic bindings.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Move omap-control binding information to the right location.
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This connects platform DAI, SiRF internal audio codec DAI and
SiRF auido port DAI together and works as a mach driver.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver is used by SIRF internal audio codec.
Use dedicated SiRF audio port TXFIFO and RXFIFO
Supports two DMA channels for SiRF audio port TXFIFO and RXFIFO
The audio port like as audio bus such as i2s.
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SiRF internal audio codec is integrated in SiRF atlas6 and prima2 SoC.
Features include:
1. Stereo DAC and ADC with 16-bit resolution amd 48KHz sample rate
2. Support headphone and/or speaker output
3. Integrate headphone and speaker output amp
4. Support LINE and MIC input
5. Support single ended and differential input mode
Signed-off-by: Rongjun Ying <rongjun.ying@csr.com>
--v5:
1. Drop all inlines.
2. Reordering the Kconfig and Makefile
3. Remove the sirf_audio_codec_reg_bits struct, use the new controls instead it.
4. Add some SND_SOC_DAPM_OUT_DRV instead of HP and SPK enable driver
5. Add audio codec clock supply instead of adc event callback
6. Fixed playback and capture can't concurrent work bug.
--
.../devicetree/bindings/sound/sirf-audio-codec.txt | 17 +
sound/soc/codecs/Kconfig | 5 +
sound/soc/codecs/Makefile | 1 +
sound/soc/codecs/sirf-audio-codec.c | 533 ++++++++++++++++++++
sound/soc/codecs/sirf-audio-codec.h | 75 +++
5 files changed, 631 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/sound/sirf-audio-codec.txt
create mode 100644 sound/soc/codecs/sirf-audio-codec.c
create mode 100644 sound/soc/codecs/sirf-audio-codec.h
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the BCM5301X/BCM470X SoCs with an ARM CPUs.
Currently just booting to a shell is working and nothing else, no
Ethernet, wifi, flash, ...
I have some pending patches to make Ethernet work for this device.
Mostly device tree support for bcma is missing.
This SoC is used in small office and home router with Broadcom SoCs
it's internal name is Northstar. This code should support the BCM4707,
BCM4708, BCM4709, BCM53010, BCM53011 and BCM53012 SoC. It uses one or
two ARM Cortex A9 Cores, some highlights are 2 PCIe 2.0 controllers,
4 Gigabit Ethernet MACs and a USB 3.0 host controller.
This SoC uses a dual core CPU, but this is currently not implemented.
More information about this SoC can be found here:
http://www.anandtech.com/show/5925/broadcom-announces-bcm4708x-and-bcm5301x-socs-for-80211ac-routers
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Christian Daudt <bcm@fixthebug.org>
Signed-off-by: Matt Porter <mporter@linaro.org>
Conflicts:
drivers/net/wireless/ath/ath9k/recv.c
drivers/net/wireless/mwifiex/pcie.c
net/ipv6/sit.c
The SIT driver conflict consists of a bug fix being done by hand
in 'net' (missing u64_stats_init()) whilst in 'net-next' a helper
was created (netdev_alloc_pcpu_stats()) which takes care of this.
The two wireless conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add anatop phandle which is used to access anatop registers to
control PHY's power and other USB operations.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add "fsl,imx6q-usbphy" for imx6dq and imx6dl, add
"fsl,imx6sl-usbphy" for imx6sl, and "fsl,imx23-usbphy"
is still a fallback for other strings.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().
However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since now we have a separate folder for phy, move the PHY dt binding
documentation of TI to that folder.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The Allwinner A31 I2C controller is almost identical to the one used in the
other Allwinner SoCs, except for the fact that it needs to clear the interrupt
by setting the INT_FLAGS bit in the control register, instead of clearing it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
The Allwinner A31 SoC using that IP has a reset controller maintaining
it reset unless told otherwise.
Add some optional reset support to the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
For imx50-weim and imx6q-weim type of devices, there might a WEIM CS
space configuration register in General Purpose Register controller,
e.g. IOMUXC_GPR1 on i.MX6Q.
Depending on which configuration of the following 4 is chosen for given
system, IOMUXC_GPR1[11:0] should be set up as 05, 033, 0113 or 01111
correspondingly.
CS0(128M) CS1(0M) CS2(0M) CS3(0M)
CS0(64M) CS1(64M) CS2(0M) CS3(0M)
CS0(64M) CS1(32M) CS2(32M) CS3(0M)
CS0(32M) CS1(32M) CS2(32M) CS3(32M)
The patch creates a function for such type of devices, which scans
'ranges' property of WEIM node and build the GPR value incrementally.
Thus the WEIM CS GPR can be set up automatically at boot time.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Philippe De Muyter <phdm@macqel.be>
Tested-by: Philippe De Muyter <phdm@macqel.be>
this moves to generic IP module reset framework, and make other drivers
use common device_reset() API.
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Bin Shi <Bin.Shi@csr.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
The Synopsys DesignWare block is used in some ARM devices (picoxcell)
and can be configured to provide multiple banks of GPIO pins.
v12: - Add irq_startup/shutdown
- do irq_create_mapping() in probe, irq_find_mapping() in to_irq()
- Adjust mappings to show support for 1 gpio per port.
- gpio-cells = <1>
v11: - Use NULL when checking existence of 'interrupts' property
- Bindings descriptions cleanup
v10: - in documentation nr-gpio -> nr-gpios
v9: - cleanup in dt bindings doc
- use of_get_child_count()
v8: - remove socfpga.dtsi changes
- minor cleanup in devicetree documentation
v7: - use irq_generic_chip
- support one irq per gpio line or one irq for many
- s/bank/port/ and other cleanup
v6: - (atull) squash the set of patches
- use linear irq domain
- build fixes. Original driver was reviewed on v3.2.
- Fix setting irq edge type for 'rising' and 'both'.
- Support as a loadable module.
- Use bgpio_chip's spinlock during register access.
- Clean up register names to match spec
- s/bank/port/ because register names use the word 'port'
- s/nr-gpio/nr-gpios/
- don't get/put the of_node
- remove signoffs/acked-by's because of changes
- other cleanup
v5: - handle sparse bank population correctly
v3: - depend on rather than select IRQ_DOMAIN
- split IRQ support into a separate patch
v2: - use Rob Herring's irqdomain in generic irq chip patches
- use reg property to indicate bank index
- support irqs on both edges based on LinusW's u300 driver
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Alan Tull <atull@altera.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove non-compatible id from examples.
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Gumstix DuoVero is an OMAP4430-based Computer On Module.
Parlor is one of the available expansion board.
Tested features:
- GPMC ethernet
- HSUSB2 and OTG
- Audio out
- WiFi and Bluetooth (w2cbw0015 SDIO module)
- LED and button
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pbias register controls internal power supply to sd card i/o pads
in most OMAPs (OMAP2-5, DRA7).
Control bits for selecting voltage level and
enabling/disabling are in the same PBIAS register.
Signed-off-by: Balaji T K <balajitk@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@linaro.org>
Tested-by: Florian Vaussard <florian.vaussard@epfl.ch>
Tested-by: Stefan Roese <sr@denx.de>
Signed-off-by: Chris Ball <chris@printf.net>
Pull networking fixes from David Miller:
1) Fix memory leak in ieee80211_prep_connection(), sta_info leaked on
error. From Eytan Lifshitz.
2) Unintentional switch case fallthrough in nft_reject_inet_eval(),
from Patrick McHardy.
3) Must check if payload lenth is a power of 2 in
nft_payload_select_ops(), from Nikolay Aleksandrov.
4) Fix mis-checksumming in xen-netfront driver, ip_hdr() is not in the
correct place when we invoke skb_checksum_setup(). From Wei Liu.
5) TUN driver should not advertise HW vlan offload features in
vlan_features. Fix from Fernando Luis Vazquez Cao.
6) IPV6_VTI needs to select NET_IPV_TUNNEL to avoid build errors, fix
from Steffen Klassert.
7) Add missing locking in xfrm_migrade_state_find(), we must hold the
per-namespace xfrm_state_lock while traversing the lists. Fix from
Steffen Klassert.
8) Missing locking in ath9k driver, access to tid->sched must be done
under ath_txq_lock(). Fix from Stanislaw Gruszka.
9) Fix two bugs in TCP fastopen. First respect the size argument given
to tcp_sendmsg() in the fastopen path, and secondly prevent
tcp_send_syn_data() from potentially using order-5 allocations.
From Eric Dumazet.
10) Fix handling of default neigh garbage collection params, from Jiri
Pirko.
11) Fix cwnd bloat and over-inflation of RTT when transmit segmentation
is in use. From Eric Dumazet.
12) Missing initialization of Realtek r8169 driver's statistics
seqlocks. Fix from Kyle McMartin.
13) Fix RTNL assertion failures in 802.3ad and AB ARP monitor of bonding
driver, from Ding Tianhong.
14) Bonding slave release race can cause divide by zero, fix from
Nikolay Aleksandrov.
15) Overzealous return from neigh_periodic_work() causes reachability
time to not be computed. Fix from Duain Jiong.
16) Fix regression in ipv6_find_hdr(), it should not return -ENOENT when
a specific target is specified and found. From Hans Schillstrom.
17) Fix VLAN tag stripping regression in BNA driver, from Ivan Vecera.
18) Tail loss probe can calculate bogus RTTs due to missing packet
marking on retransmit. Fix from Yuchung Cheng.
19) We cannot do skb_dst_drop() in iptunnel_pull_header() because
multicast loopback detection in later code paths need access to
skb_rtable(). Fix from Xin Long.
20) The macvlan driver regresses in that it propagates lower device
offload support disables into itself, causing severe slowdowns when
running over a bridge. Provide the software offloads always on
macvlan devices to deal with this and the regression is gone. From
Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (103 commits)
macvlan: Add support for 'always_on' offload features
net: sctp: fix sctp_sf_do_5_1D_ce to verify if we/peer is AUTH capable
ip_tunnel:multicast process cause panic due to skb->_skb_refdst NULL pointer
net: cpsw: fix cpdma rx descriptor leak on down interface
be2net: isolate TX workarounds not applicable to Skyhawk-R
be2net: Fix skb double free in be_xmit_wrokarounds() failure path
be2net: clear promiscuous bits in adapter->flags while disabling promiscuous mode
be2net: Fix to reset transparent vlan tagging
qlcnic: dcb: a couple off by one bugs
tcp: fix bogus RTT on special retransmission
hsr: off by one sanity check in hsr_register_frame_in()
can: remove CAN FD compatibility for CAN 2.0 sockets
can: flexcan: factor out soft reset into seperate funtion
can: flexcan: flexcan_remove(): add missing netif_napi_del()
can: flexcan: fix transition from and to freeze mode in chip_{,un}freeze
can: flexcan: factor out transceiver {en,dis}able into seperate functions
can: flexcan: fix transition from and to low power mode in chip_{en,dis}able
can: flexcan: flexcan_open(): fix error path if flexcan_chip_start() fails
can: flexcan: fix shutdown: first disable chip, then all interrupts
USB AX88179/178A: Support D-Link DUB-1312
...
When device is booted using devicetree, platforms impacted by Erratum
2.1.1.128 is not detected easily in the mmc driver. This erratum
indicates that the module cannot do multi-block transfers. Platforms
such as LDP which use OMAP3 ES revision prior to ES3.0 are impacted by
this.
Provide a new compatible property "ti,omap3-pre-es3-hsmmc" to allow
driver to determine if driver needs to implement quirks associated
with the specific module version (primarily because the IP revision
information is not sufficient for the same).
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds the iommu bindings for all OMAP2+ SoCs. Apart from
the standard bindings used by OMAP peripherals, this patch uses a
'dma-window' (already used by Tegra SMMU) and adds two OMAP custom
bindings - 'ti,#tlb-entries' and 'ti,iommu-bus-err-back'.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: split bindings document, add dra7 and bus error back]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Joerg Roedel <joro@8bytes.org>
This reverts commit 40b367d95f.
Russell King has raised the idea of creating a proper PMU driver for
this SoC that would incorporate the functionality currently in this
driver. It would also cover the use case for the graphics subsystem on
this SoC.
To prevent having to maintain the devicetree ABI for this limited
interrupt-handler driver, we revert the driver before it hits a mainline
tagged release (eg v3.15).
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@googlemail.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Link: http://lkml.kernel.org/r/1393911160-7688-1-git-send-email-jason@lakedaemon.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
support pfuze200 chip which remove SW1C and SW4 based on pfuze100.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The similar GPIO HW block is used by keystone SoCs as
in Davinci SoCs.
Hence, reuse Davinci GPIO driver for Keystone taking into
account that Keystone contains ARM GIC IRQ controller which
is implemented using IRQ Chip.
Documentation:
http://www.ti.com/lit/ug/sprugv1/sprugv1.pdf
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reserved memory nodes allow for the reservation of static (fixed
address) regions, or dynamically allocated regions for a specific
purpose.
[joshc: Based on binding document proposed (in non-patch form) here:
http://lkml.kernel.org/g/20131030134702.19B57C402A0@trevor.secretlab.ca
adapted to support #memory-region-cells]
Signed-off-by: Josh Cartwright <joshc@codeaurora.org>
[mszyprow: removed #memory-region-cells property]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
[grant.likely: removed residual #memory-region-cells example]
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The Synology NAS devices use a very similar mechanism to QNAP NAS
devices to power off. Both send a single charactor command to a PIC,
over the second serial port. However the baud rate and the command
differ. Generalize the driver to support this.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Cc: Anton Vorontsov <anton@enomsg.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
regressions. There is a single framework fix that prevents dereferencing
a NULL pointer when calling clk_get. The range of fixes for clock driver
regressions spans memory leak fixes, touching the wrong registers that
cause things to explode, misconfigured clock rates that result in
non-responsive devices and even some boot failures. The most benign fix
is DT binding doc typo. It is a stable ABI exposed from the kernel that
was introduced in -rc1, so best to fix it now.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=zck4
-----END PGP SIGNATURE-----
Merge tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux
Pull clk framework fixes from Mike Turquette:
"Clock framework and driver fixes, all of which fix user-visible
regressions.
There is a single framework fix that prevents dereferencing a NULL
pointer when calling clk_get. The range of fixes for clock driver
regressions spans memory leak fixes, touching the wrong registers that
cause things to explode, misconfigured clock rates that result in
non-responsive devices and even some boot failures. The most benign
fix is DT binding doc typo. It is a stable ABI exposed from the
kernel that was introduced in -rc1, so best to fix it now"
* tag 'clk-fixes-for-linus' of git://git.linaro.org/people/mike.turquette/linux: (25 commits)
clk:at91: Fix memory leak in of_at91_clk_master_setup()
clk: nomadik: fix multiplatform problem
clk: Correct handling of NULL clk in __clk_{get, put}
clk: shmobile: Fix typo in MSTP clock DT bindings
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent for all non-PLL clocks
clk: tegra124: remove gr2d and gr3d clocks
clk: tegra: Fix vic03 mux index
clk: shmobile: rcar-gen2: Fix qspi divisor
clk: shmobile: rcar-gen2: Fix clock parent all non-PLL clocks
clk: tegra: use max divider if divider overflows
clk: tegra: cclk_lp has a pllx/2 divider
clk: tegra: fix sdmmc clks on Tegra1x4
clk: tegra: fix host1x clock on Tegra124
clk: tegra: PLLD2 fixes for hdmi
clk: tegra: Fix PLLD mnp table
clk: tegra: Fix PLLP rate table
clk: tegra: Correct clock number for UARTE
clk: tegra: Add missing Tegra20 fuse clks
ARM: keystone: dts: fix clkvcp3 control register address
...
The Allwinner A1x / A2x SoCs have 2 or 3 usb phys which are all accessed
through a single set of registers. Besides this there are also some other
phy related bits which need poking, which are per phy, but shared between the
ohci and ehci controllers, so these are also controlled from this new phy
driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Eric Bénard <eric@eukrea.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: alsa-devel@alsa-project.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Denis Carikli <denis@eukrea.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds the dts bindings documenation for the Altera SOCFPGA glue
layer for the Synopsys STMMAC ethernet driver.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: David S. Miller <davem@davemloft.net>
---
v3: Remove stray empty line at end of socfpga_cyclone5_socdk.dts
v2: Use the dwmac-sti as an example for a glue layer and split patch up
to have dts as a separate patch. Also cc dts maintainers since there is
a new binding.
Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.
Add documentation for the DMM bindings.
Originally worked on by Andy Gross <andygro@gmail.com>
Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
AM437x GP EVM DTS with pinmux information to make I2C on
EVM usable.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Pull slave-dma fixes from Vinod Koul:
"This request brings you two small fixes. First one for fixing
dereference of freed descriptor and second for fixing sdma bindings
for it to work for imx25.
I was planning to send this about 10days ago but then I had to proceed
on my paternity leave and didnt get chance to send this. Now got a
bit of time from dady duties :)"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: sdma: Add imx25 compatible
dma: ste_dma40: don't dereference free:d descriptor
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTCqL6AAoJEHm+PkMAQRiGljYIAICQIZsXmMc/pUC3hHgTr2KK
BBQXjnoE7tDN/QkZQzSj/+VqP1/Ndo7lQlXThXuooNhemjpmFCd8AIRhXi164NPE
NoAZ0efWu1kE3iAJKyHN11zVlv4NS0bsTlNAgPN0EwjDBTTk5thfiZBqNz56cWrZ
MqH8tKpUTuAPciXeyB6WI34pKMkzB+Urfoweum7euk8WyDw7kthpncwEt+fzBAKm
20+N2JVoHN7h2xuR4mx8rDXPbXlwPCH5K/8NapytbP7xWBJ3UaOjbbcKHbydrfkI
1eOlajXafFrjN/XTXDySqQg9lT6DoszOE0fhAZyrdPPqvbQOU64WdBcYyOg8ObI=
=KxaP
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc4' into next
Merge with Linux 3.14-rc4 to bring devm_request_any_context_irq().
The pmu is needed to bring up the cores during smp operations and later
also other system parts. Therefore add a node and documentation for it.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Add dt-nodes for the sram on rk3066 and rk3188 including the reserved section
needed for smp bringup.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
The Xilinx XADC is a ADC that can be found in the series 7 FPGAs from Xilinx.
The XADC has a DRP interface for communication. Currently two different
frontends for the DRP interface exist. One that is only available on the ZYNQ
family as a hardmacro in the SoC portion of the ZYNQ. The other one is available
on all series 7 platforms and is a softmacro with a AXI interface. This binding
document describes the bindings for both of them since the bindings are very
similar.
Each of them needs:
* A address range where the registers are mapped
* An interrupt number for the device interrupt
* A clock. For the the ZYNQ hardmacro interface this is the modules PCAP
clock, for the AXI softmacro it is the AXI bus interface clock.
Additionally the bindings specify whether an external multiplexer is used and in
which mode it is used. The devicetree bindings also describe which external
channels are connected and in which configuration.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add bindings for TI Async External Memory Interface (AEMIF) controller.
The Async External Memory Interface (EMIF16/AEMIF) controller is intended to
provide a glue-less interface to a variety of asynchronous memory devices like
ASRA M, NOR and NAND memory. A total of 256M bytes of any of these memories
can be accessed via 4 chip selects with 64M byte access per chip select.
We are not encoding CS number in reg property, it's memory partition number.
The CS number is encoded for Davinci NAND node using standalone property
"ti,davinci-chipselect" and we need to provide two memory ranges to it,
as result we can't encode CS number in "reg" for AEMIF child devices
(NAND/NOR/etc), as it will break bindings compatibility.
In this patch, NAND node is used just as an example of child node.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some SoCs need parts of their sram for special purposes. So while being part
of the peripheral, it should not be part of the genpool controlling the sram.
Therefore add the option to define reserved regions as subnodes of the
sram-node similar to defining reserved global memory regions.
Originally
Suggested-by: Rob Herring <robherring2@gmail.com>
Using subnodes for reserved regions
Suggested-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Ulrich Prinz <ulrich.prinz@googlemail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add device tree binding documentation for Texas Instrument's wl1251
wireless lan chip. For now only the SPI binding is documented.
Signed-off-by: Sebastian Reichel <sre@debian.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some gpio-leds need retain the state even in suspend, such as charger led.
But this property missed in devicetree, add it.
(cooloney@gmail.com: fold DT binding updates into this patch)
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
This patch adds devicetree support for the MC13XXX LED driver.
(cooloney@gmail.com: remove unneeded semicolon)
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
Add support for the MSIOF variant in the R-Car H2 (r8a7790) and M2
(r8a7791) SoCs.
Binding documentation:
- Add future-proof "renesas,msiof-<soctype>" compatible values,
- The default for "renesas,rx-fifo-size" is 256 on R-Car H2 and M2,
- "renesas,tx-fifo-size" and "renesas,rx-fifo-size" are deprecated for
soctype-specific bindings,
- Add example bindings.
Implementation:
- MSIOF on R-Car H2 and M2 requires the transmission of dummy data if
data is being received only (cfr. "Set SICTR.TSCKE to 1" and "Write
dummy transmission data to SITFDR" in paragraph "Transmit and Receive
Procedures" of the Hardware User's Manual).
- As RX depends on TX, MSIOF on R-Car H2 and M2 also lacks the RSCR
register (Receive Clock Select Register), and some bits in the RMDR1
(Receive Mode Register 1) and TMDR2 (Transmit Mode Register 2)
registers.
- Use the recently introduced SPI_MASTER_MUST_TX flag to enable support
for dummy transmission in the SPI core, and to differentiate from other
MSIOF implementations in code paths that need this.
- New DT compatible values ("renesas,msiof-r8a7790" and
"renesas,msiof-r8a7791") are added, as well as new platform device
names ("spi_r8a7790_msiof" and "spi_r8a7791_msiof").
- The default RX FIFO size is 256 words on R-Car H2 and M2.
This is loosely based on a set of patches from Takashi Yoshii
<takasi-y@ops.dti.ne.jp>.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
Documentation:
- Add missing "interrupt-parent", "#address-cells", "#size-cells", and
"clocks" properties,
- Add missing default values for "num-cs", "renesas,tx-fifo-size" and
"renesas,rx-fifo-size",
- Add a reference to the pinctrl documentation.
Implementation:
- As "num-cs" is marked optional, provide a sensible default.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver supports the GPIO controller found in LSI ZEVIO SoCs.
It has been successfully tested on a TI nspire CX calculator.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Document what we (Laurent and I, following a mailing list dicussion)
believe are best practices for the polarity flag in a GPIO specifier.
While touching the doc, I made a few minor editing changes to other
areas.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Updates from Jean-Fracois for the TDA998x driver, which are on top of
the fixes you have previously pulled, except these changes aren't
intended for -rc, but the next merge window.
Several of these are issues of correctness - passing more correct HDMI
info packets, not reading registers in older chips documented as write
only (despite appearing to be read/write in later chips). Others are
code cleanups (using definitions rather than constants where we have
them already in the kernel).
Additional functionality is also added by way of optional support for
the IRQ from the TDA998x, which allows us to avoid busy-waiting for
the EDID reads.
* 'tda998x-devel' of git://ftp.arm.linux.org.uk/~rmk/linux-cubox:
drm/i2c: tda998x: always use the same device for all kernel messages
drm/i2c: tda998x: adjust the audio clock divider for S/PDIF
drm/i2c: tda998x: code optimization
drm/i2c: tda998x: remove the unused variable ca_i2s
drm/i2c: tda998x: make the audio code more readable
drm/i2c: tda998x: use irq for connection status and EDID read
drm/i2c: tda998x: always enable EDID read IRQ
drm/i2c: tda998x: add DT documentation
drm/i2c: tda998x: add DT support
drm/i2c: tda998x: don't read write-only registers
drm/i2c: tda998x: don't freeze the system at audio startup time
drm/i2c: tda998x: change probe message origin
drm/i2c: tda998x: code cleanup
drm/i2c: tda998x: clean up error chip version checking
drm/i2c: tda998x: check more I/O errors
drm/i2c: tda998x: simplify the i2c read/write functions
drm/i2c: tda998x: use ALSA IEC958 definitions and update audio frequency
drm/i2c: tda998x: add the active aspect in HDMI AVI frame
drm/i2c: tda998x: use HDMI constants
This reverts tlv320aic32x4 as compatible for tlv320aic3x as it has its
own bindings now.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduce "altr,socfpga-dw-mshc" to enable Altera's SOCFPGA platform
specific implementation of the dw_mmc driver.
Also add the "syscon" binding to the "altr,sys-mgr" node. The clock
driver can use the syscon driver to toggle the register for the SD/MMC
clock phase shift settings.
Finally, fix an indentation error for the sysmgr node.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Tested-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Chris Ball <chris@printf.net>
This patch adds support for the new v2 version of the axi-clkgen core.
Unfortunately the method of accessing the registers is quite different on v2,
while the content still stays largely the same. So the patch adds a small
abstraction layer which implements the specific read and write functions for v1
and v2 in callback functions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Suggest by Arnd: abstract mmc tuning as clock behavior,
also because different soc have different tuning method and registers.
hi3620_mmc_clks is added to handle mmc clock specifically on hi3620.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
While we are here, also brush up the devicetree binding documentation.
The example was an inappropriate copy from the sh_mobile driver.
Signed-off-by: Wolfram Sang <wsa@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Add support for the led-mode property for the following PHYs
which have a single LED mode configuration value.
KSZ8001 and KSZ8041 which both use register 0x1e bits 15,14 and
KSZ8021, KSZ8031 and KSZ8051 which use register 0x1f bits 5,4
to control the LED configuration.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch replaces magic numbers with macros defined in DT header
in exynos5440 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos5420 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos5250 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The patch replaces magic numbers with macros defined in DT header
in exynos4 clock bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Tomasz Figa <t.figa@samsung.com>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Dove pinctrl binding now requires three different reg properties. This
updates corresponding binding and example accordingly. While at it, also
document reg property as required for the other MVEBU SoC pinctrl nodes.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Marvell Dove SoC binding was not documented, yet. Add the documentation
and also describe Global Configuration register node in it.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Armada 380/385 are new ARM SoCs from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
The Marvell Armada 375 is a new ARM SoC from Marvell, part of the
mvebu family, but using a Cortex-A9 CPU core. In terms of pin-muxing,
it is similar to Armada 370 and XP for the register layout, only
different in the number of available pins and their
functions. Therefore, we simply use the existing
drivers/pinctrl/mvebu/ infrastructure, with no other changes that the
list of pins and corresponding functions.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
- mvebu
- initial support for Armada 375, 380, and 385
Depends:
- tags/mvebu-soc-3.15 (resolves delete/rename hidden conflict)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=LIE3
-----END PGP SIGNATURE-----
Merge tag 'mvebu-soc-3xx-3.15' of git://git.infradead.org/linux-mvebu into next/soc
Merge "mvebu new SoCs for v3.15" from Jason Cooper:
- mvebu
- initial support for Armada 375, 380, and 385
Depends:
- tags/mvebu-soc-3.15 (resolves delete/rename hidden conflict)
* tag 'mvebu-soc-3xx-3.15' of git://git.infradead.org/linux-mvebu:
Documentation: arm: update Marvell documentation about Armada 375/38x
ARM: mvebu: add initial support for the Armada 380/385 SOCs
ARM: mvebu: add workaround for data abort issue on Armada 375
ARM: mvebu: add initial support for the Armada 375 SOCs
ARM: mvebu: add Armada 375 support to the system-controller driver
ARM: mvebu: make CPU_PJ4B selection a per-SoC choice
ARM: mvebu: rename DT machine structure for Armada 370/XP
ARM: mvebu: rename armada-370-xp.c to board-v7.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- orion watchdog
- cleanup and extend driver to support Armada 370 and Armada XP
Depends:
- tags/irqchip-mvebu-fixes-3.14 (already pulled by tglx)
- both are based on v3.14-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=3VWF
-----END PGP SIGNATURE-----
Merge tag 'mvebu-watchdog-3.15' of git://git.infradead.org/linux-mvebu into next/drivers
mvebu watchdog driver changes for v3.15
- orion watchdog
- cleanup and extend driver to support Armada 370 and Armada XP
Depends:
- tags/irqchip-mvebu-fixes-3.14 (already pulled by tglx)
- both are based on v3.14-rc1
* tag 'mvebu-watchdog-3.15' of git://git.infradead.org/linux-mvebu:
watchdog: orion: Enable the build on ARCH_MVEBU
watchdog: orion: Add support for Armada 370 and Armada XP SoC
watchdog: orion: Add per-compatible watchdog start implementation
watchdog: orion: Add per-compatible clock initialization
watchdog: orion: Introduce per-compatible of_device_id data
watchdog: orion: Introduce an orion_watchdog device structure
watchdog: orion: Remove unneeded BRIDGE_CAUSE clear
watchdog: orion: Make RSTOUT register a separate resource
watchdog: orion: Handle the interrupt so it's properly acked
watchdog: orion: Make sure the watchdog is initially stopped
watchdog: orion: Remove unused macros
watchdog: orion: Use atomic access for shared registers
watchdog: orion: Add clock error handling
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The compatible string of the Broadcom Capri pinctrl driver is renamed to
"brcm,bcm11351-pinctrl" to match the machine binding here:
Documentation/devicetree/bindings/arm/bcm/bcm11351.txt
Signed-off-by: Sherman Yin <syin@broadcom.com>
Reviewed-by: Matt Porter <mporter@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Christian Daudt <bcm@fixthebug.org>
This patch makes it possible to set the chipidea udc into full-speed only mode.
It is set by the oftree property "maximum-speed = full-speed".
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds descriptions for new properties of the device tree
binding for the ARM SMMU architecture. These properties control
arm-smmu driver options.
Cc: Grant Likely <grant.likely@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Andreas Herrmann <andreas.herrmann@calxeda.com>
[will: removed device isolation property, as this has been dropped and
fixed up spacing in documentation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
The DT bindings document a renesas,indices property, while the code, the
DT example and the DT sources all use renesas,clock-indices. Fix the
documentation.
The shmobile mstp DT bindings have been merged in v3.14-rc1 with a bug
in the DT ABI, a fix during the -rc series is appropriate.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms@verge.net.au>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
Conflicts:
arch/arm/mach-at91/at91sam9260.c
arch/arm/mach-at91/at91sam9261.c
arch/arm/mach-at91/at91sam9263.c
arch/arm/mach-at91/at91sam9rl.c
arch/arm/mach-mmp/time.c
arch/arm/mach-sa1100/time.c
A collection of fixes for ARM platforms. Most are fixes for DTS files,
mostly from DT conversion on OMAP which is still finding a few issues here
and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache configuration
fix for Tegra, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=i7LS
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A collection of fixes for ARM platforms. Most are fixes for DTS
files, mostly from DT conversion on OMAP which is still finding a few
issues here and there.
There's a couple of small stale code removal patches that we usually
queue for the next release instead, but they seemed harmless enough to
bring in now.
Also, a fix for backlight on some PXA platforms, and a cache
configuration fix for Tegra, etc"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (25 commits)
MAINTAINERS: add additional ARM BCM281xx/BCM11xxx maintainer
ARM: tegra: only run PL310 init on systems with one
ARM: tegra: Add head numbers to display controllers
ARM: imx6: build pm-imx6q.c independently of CONFIG_PM
ARM: tegra: fix RTC0 alias for Cardhu
ARM: dove: dt: revert PMU interrupt controller node
Documentation: dt: OMAP: Update Overo/Tobi
ARM: dts: Add support for both OMAP35xx and OMAP36xx Overo/Tobi
ARM: dts: omap3-tobi: Use the correct vendor prefix
ARM: dts: omap3-tobi: Fix boot with OMAP36xx-based Overo
ARM: OMAP2+: Remove legacy macros for zoom platforms
ARM: OMAP2+: Remove MACH_NOKIA_N800
ARM: dts: N900: add missing compatible property
ARM: dts: N9/N950: fix boot hang with 3.14-rc1
ARM: OMAP1: nokia770: enable tahvo-usb
ARM: OMAP2+: gpmc: fix: DT ONENAND child nodes not probed when MTD_ONENAND is built as module
ARM: OMAP2+: gpmc: fix: DT NAND child nodes not probed when MTD_NAND is built as module
ARM: dts: omap3-gta04: Fix mmc1 properties.
ARM: dts: omap3-gta04: Fix 'aux' gpio key flags.
ARM: OMAP2+: add missing ARCH_HAS_OPP
...
- mvebu (Armada 375/380/385)
- extend corediv clock driver to support new SoCs
- add core and gating clock drivers for new SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Aah7
-----END PGP SIGNATURE-----
Merge tag 'clk-mvebu-3xx-3.15' of git://git.infradead.org/linux-mvebu into clk-next-mvebu
clock: mvebu new SoC changes for v3.15
- mvebu (Armada 375/380/385)
- extend corediv clock driver to support new SoCs
- add core and gating clock drivers for new SoCs
Add a property called clock-indices to allow clock-output-names
to be used where the index used to lookup a clock is not a 1:1
mapping to the array position in the clock-output-names
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
There are a few fixes in here that might, earlier in a cycle, have gone
to Greg as fixes. Given they are either minor or have never actually
been observed as causing trouble (the locking bug in the event code) and
are invasive, I have included them in this pull request, targeting the
3.15 merge window instead.
The rest are pretty uncontroversial new drivers, a handy little tool for
the example code in our documentation and little cleanups.
New drivers
* Freescale Vybrid and i.MX6SLX ADC driver.
* HID Sensor hub proximity sensors.
* HID Sensor hub pressure sensors.
* LPS25H Pressure sensors added to the ST micro pressure sensor driver.
New functionality
* lsiio tool. This is added to the staging tree as we haven't yet moved
the example code it sits with out. Moving this code out is now a reasonably
high priority but holding up this tool in the meantime did not seem
worthwhile.
* mag3110 - add missing scale factor for temperature output to userspace.
Cleanups
* Fix a bug in the event reporting in which a spin lock might be held over
when a sleep occured. A similar bug was found by Lars in the buffer code.
It has not to our knowledge been observed as actually occuring and is
a little too invasive to push out as a fix.
* Drop the IIO_ST macro after clearing out all users. This macro was a very
bad idea leading to a number of bugs after it stopped covering all elements
of the structure being assigned and people started making assumptions about
what it did cover. Glad to see it go!
* Avoid applying extended name to shared attributes as it makes no sense.
No in tree drivers were using the combination, hence not pushed out as
a fix.
* ad799x - move to devm_request_threaded_irq to reduce boilerplate clean up.
* bma180 - make the low_pass_filter_3db_frequency info element shared rather
than per attribute. The old approach was valid but not as clean as it might
be and was setting a bad example. Hence the cleanup.
* mxs-lradc - propogate the error code form a platform_get_irq call rather than
eating it up by returning -EINVAL on all errors.
* ad799x - typo fix in the copyright message. Either that or Michael was
asserting a copyright that moved backwards in time by about a thousand years.
* ad799x - use a regulator for vref rather than platform data. The driver
dates from just as the regulator framework was coming into common use so
provides an alternative way of specifying the reference voltage. We no
longer need that approach so drop it in favour of a regulator only approach.
* max1363 - some internal vref values were out by a small amount. The effect
would have been tiny and no one noticed hence not pushing this through as
a fix.
* core - replace some pointless goto error_ret (with no clean up) lines with
direct returns. This is my bad coding style so I'm glad to see it cleaned
up.
* core - avoid a kasprintf that just directly prints a string with no
formatting elements. This has always been there but Lars just noticed it.
Oops.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=Dg3R
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.15b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second round of IIO new driver, functionality and cleanups for the 3.15 series.
There are a few fixes in here that might, earlier in a cycle, have gone
to Greg as fixes. Given they are either minor or have never actually
been observed as causing trouble (the locking bug in the event code) and
are invasive, I have included them in this pull request, targeting the
3.15 merge window instead.
The rest are pretty uncontroversial new drivers, a handy little tool for
the example code in our documentation and little cleanups.
New drivers
* Freescale Vybrid and i.MX6SLX ADC driver.
* HID Sensor hub proximity sensors.
* HID Sensor hub pressure sensors.
* LPS25H Pressure sensors added to the ST micro pressure sensor driver.
New functionality
* lsiio tool. This is added to the staging tree as we haven't yet moved
the example code it sits with out. Moving this code out is now a reasonably
high priority but holding up this tool in the meantime did not seem
worthwhile.
* mag3110 - add missing scale factor for temperature output to userspace.
Cleanups
* Fix a bug in the event reporting in which a spin lock might be held over
when a sleep occured. A similar bug was found by Lars in the buffer code.
It has not to our knowledge been observed as actually occuring and is
a little too invasive to push out as a fix.
* Drop the IIO_ST macro after clearing out all users. This macro was a very
bad idea leading to a number of bugs after it stopped covering all elements
of the structure being assigned and people started making assumptions about
what it did cover. Glad to see it go!
* Avoid applying extended name to shared attributes as it makes no sense.
No in tree drivers were using the combination, hence not pushed out as
a fix.
* ad799x - move to devm_request_threaded_irq to reduce boilerplate clean up.
* bma180 - make the low_pass_filter_3db_frequency info element shared rather
than per attribute. The old approach was valid but not as clean as it might
be and was setting a bad example. Hence the cleanup.
* mxs-lradc - propogate the error code form a platform_get_irq call rather than
eating it up by returning -EINVAL on all errors.
* ad799x - typo fix in the copyright message. Either that or Michael was
asserting a copyright that moved backwards in time by about a thousand years.
* ad799x - use a regulator for vref rather than platform data. The driver
dates from just as the regulator framework was coming into common use so
provides an alternative way of specifying the reference voltage. We no
longer need that approach so drop it in favour of a regulator only approach.
* max1363 - some internal vref values were out by a small amount. The effect
would have been tiny and no one noticed hence not pushing this through as
a fix.
* core - replace some pointless goto error_ret (with no clean up) lines with
direct returns. This is my bad coding style so I'm glad to see it cleaned
up.
* core - avoid a kasprintf that just directly prints a string with no
formatting elements. This has always been there but Lars just noticed it.
Oops.
For some CPU/CODEC DAI devices the slot information maybe needed. This
patch adds the slot information parsing for simple-card driver.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support regulators to power up the codec. This patch also enables the
AVDD LDO if no AV regulator was found.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for a master clock passed through DT. The master clock of
the codec is only active when the codec is in use.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
List full example compatible properties with soctypes instead of just the
soctypes, so checkpatch can validate DTSes.
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The older Allwinner SoCs (A10, A13, A10s and A20) all have the same SPI
controller.
Unfortunately, this SPI controller, even though quite similar, is significantly
different from the recently supported A31 SPI controller (different registers
offset, split/merged registers, etc.). Supporting both controllers in a single
driver would be unreasonable, hence the addition of a new driver.
Like its more recent counterpart, it supports DMA, but the driver only does PIO
until we have a dmaengine driver for this platform.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Instantiate the L2 cache from DT. Indicate in DT where the cache
control register is so that it is possible to enable/disable write
through on the CPU.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The ahci_platform driver supports "snps,dwc-ahci".
Add this to the DT binding information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoids the ugliness of creating a nested platform device from probe.
While moving it around anyways, move the mk6q phy init code from probe
to imx_sata_enable, as the phy needs to be re-initialized on resume too,
otherwise the drive won't be recognized after resume.
Tested on a wandboard i.mx6 quad.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for the ahci sata controler found on Allwinner A10
and A20 SoCs to the ahci_platform driver.
Orignally written by Olliver Schinagl using the approach of having a platform
device which probe method creates a new child platform device which gets
driven by ahci_platform.c, as done by ahci_imx.c .
Refactored by Hans de Goede to add most of the non sunxi specific functionality
to ahci_platform.c and use a platform_data pointer from of_device_id for the
sunxi specific bits.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The allwinner-sun4i AHCI controller needs 2 clocks to be enabled and the
imx AHCI controller needs 3 clocks to be enabled.
tj: Minor comment formatting updates.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
Provide the option to configure these speed modes per host, for those
host driver's that can't distinguish this in runtime.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
The new Armada 375 and Armada 38x Marvell SoCs are based on Cortex-A9
CPU cores and use the ARM GIC as their main interrupt controller.
However, for various purposes (wake-up from suspend, MSI interrupts),
they have kept a separate MPIC interrupt controller, acting as a slave
to the GIC. This MPIC was already used as the primary controller on
previous Marvell SoCs, so this commit extends the existing driver to
allow the MPIC to be used as a GIC slave.
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Using the added infrastructure for handling SoC differences,
this commit adds support for the watchdog controller available
in Armada 370 and Armada XP SoCs.
Also, and because the AXP clock initialization uses of_clk_get_by_name,
this commit changes the orion clock initialization to use clk_get() and
adds a proper clk_put() on the common exit/error paths.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
In order to support other SoC, it's required to distinguish
the 'control' timer register, from the 'rstout' register
that enables system reset on watchdog expiration.
To prevent a compatibility break, this commit adds a fallback
to a hardcoded RSTOUT address.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
DT-enabled plaforms, where the irqchip driver for the brigde interrupt
controller is available, can handle the watchdog IRQ properly. Therefore,
request the interrupt and add a dummy handler that merely calls panic().
This is done in order to have an initial 'ack' of the interruption,
which clears the watchdog state.
Furthermore, since some platforms don't have such IRQ, this commit
makes the interrupt specification optional.
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Tested-By: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the Seiko Instruments Inc S35390a to the list of trivial i2c
devices.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The following patches make use of vendor names:
* ricoh (Ricoh Co. Ltd.);
* qnap (QNAP Systems, Inc.);
* sii (Seiko Instruments, Inc.); and
* synology (Synology, Inc.)
Add them to the vendor prefix list.
Signed-off-by: Ben Peddell <klightspeed@killerwolves.net>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the basic support for the Armada 380 and Armada 385
SOCs. These SoCs share most of their IP with the Armada 370/XP
SoCs. The main difference is the use of a Cortex A9 CPU instead of the
PJ4B CPU. The Armada 380 is a single core Cortex-A9, while the Armada
385 is a dual-core Cortex-A9.
The support is introduced in board-v7.c, together with Armada 370/XP,
but a separate DT structure is added, because Armada 38x will need a
different set of SMP operations when the SMP support is introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
This commit adds the basic support for the Armada 375 SOCs. These SoCs
share most of their IP with the Armada 370/XP SoCs. The main
difference is the use of a Cortex A9 CPU instead of the PJ4B CPU. The
interrupt controller and the L2 cache controller are also different
they are respectively the GIC and the PL310.
The support is introduced in board-v7.c, together with Armada 370/XP,
but a separate DT structure is added, because Armada 375 will need a
different set of SMP operations when the SMP support is introduced.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The system controller block in the Armada 375 has different register
offsets for the system reset and other related functions. Therefore,
this commit introduces the new "armada-375-system-controller"
compatible string to identify the Armada 375 variant of the system
controller.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
- Move integrator clock definitions to the device tree, alter
clock and timer drivers accordingly.
- Alter the VIC irqchip driver to support cascaded VICs off
a parent IRQ controller.
- Update the IM-PD1 plugin code to use managed resources.
- Register the VIC on the IM-PD1.
- Select the PL061 GPIO block for the IM-PD1 on the
Integrator/AP.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=a4vs
-----END PGP SIGNATURE-----
Merge tag 'integrator-for-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator into next/drivers
Merge "Integrator/Versatile base patch stack for the v3.15 series"
from Linus Walleij:
"this is a set of patches I have sent for review and failed to get ACKs
from the proper subsystem maintainers after repeated pings. However I
now need to have this rotated in linux-next as a base for multiplatform,
so please pull it in, it is all ARM drivers anyway. Russell pointed out
some things and these have been fixed and iterated in this series."
- Move integrator clock definitions to the device tree, alter
clock and timer drivers accordingly.
- Alter the VIC irqchip driver to support cascaded VICs off
a parent IRQ controller.
- Update the IM-PD1 plugin code to use managed resources.
- Register the VIC on the IM-PD1.
- Select the PL061 GPIO block for the IM-PD1 on the
Integrator/AP.
* tag 'integrator-for-v3.15-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-integrator:
ARM: integrator: select GPIO block
ARM: integrator: register the IM-PD1 VIC
ARM: integrator: use managed resources for the IM-PD1
irqchip: support cascaded VICs
irqchip: vic: update the base IRQ member correctly
clk: versatile: respect parent rate in ICST clock
clk: versatile: pass a parent to the ICST clock
ARM: integrator: switch to fetch clocks from device tree
ARM: SP804: make Integrator/CP timer pick clock from DT
ARM: integrator: define clocks in the device trees
Signed-off-by: Olof Johansson <olof@lixom.net>
Cortex-A12 implements Performance Monitors compliant with the PMUv2
architecture.
This patch adds support for the Cortex-A12 PMU to the ARM perf backend.
Signed-off-by: Albin Tonnerre <albin.tonnerre@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
* Add support for determining smp ops based on device tree.
* Add DT binding specs for Krait/Scorpion enable method
* Add DT binding specs for various Krait Processor controller complexes
* Add SoC SMP support for Krait Processor Subsystem v1 & v2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)
Comment: GPGTools - https://gpgtools.org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=R5RP
-----END PGP SIGNATURE-----
Merge tag 'qcom-soc-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/soc
Merge "Qualcomm ARM Based SoC Updates for v3.15" from Kumar Gala:
* Add support for determining smp ops based on device tree.
* Add DT binding specs for Krait/Scorpion enable method
* Add DT binding specs for various Krait Processor controller complexes
* Add SoC SMP support for Krait Processor Subsystem v1 & v2
* tag 'qcom-soc-for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: qcom: Add SMP support for KPSSv2
ARM: qcom: Add SMP support for KPSSv1
devicetree: bindings: Document qcom,saw2 node
devicetree: bindings: Document qcom,kpss-acc
devicetree: bindings: Document Krait/Scorpion cpus and enable-method
ARM: qcom: Re-organize platsmp to make it extensible
ARM: Introduce CPU_METHOD_OF_DECLARE() for cpu hotplug/smp
ARM: qcom: Rename various msm prefixed functions to qcom
clocksource: qcom: split building of legacy vs multiplatform support
ARM: qcom: Split Qualcomm support into legacy and multiplatform
clocksource: qcom: Move clocksource code out of mach-msm
ARM: msm: kill off hotplug.c
ARM: msm: Remove pen_release usage
ARM: dts: msm: split out msm8660 and msm8960 soc into dts include
Signed-off-by: Olof Johansson <olof@lixom.net>
- New SoC device tree support for imx35 and imx50
- A good number of new board support: imx25-eukrea, imx28-duckbill,
imx28-eukrea, Eukrea cpuimx35, imx50-evk, imx51-eukrea, imx53-voipac,
MCIMX53-START-R and Ka-Ro TX53.
- Quite some updates and tweaking on imx27 phycore and apf27dev boards
- Add pinfunc headers for imx25, imx27 and imx50
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Use clock defines in imx5 DTS files
- Use macros for interrupt and gpio flags
- A plenty of random updates on various SoC and board device tree
sources, adding pinctrl settings, device nodes, properties, aliases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS94QdAAoJEFBXWFqHsHzO9KkH/i23jhVVQcb2XXh81moW1LAM
QsPn3MpdPqTi3XDZ7mbsFlMJrucs1tHhMbnx9vI3Sc3IUtc/GPMqrF3CUwgd+hpZ
TfA79oJPeDYAj/7JqqsEnhQyBvlsUf4xdqFs8N0A0YxN9xfVtumpWHHFlOU2s3IW
tLczVI2dtXEzvvrFXlQtGv/fKKGZKzohwtbn4lE0CopeqGihvBBNr/v1SpoTm91S
Qxs+5hZR8GOmtatUPnirE9Di4U4T0cYcpBqk9iCWUQ2fvPNrk9/AE7zaohcX6z68
tUI2l8iU/fMx5t84m1brK/aVD+tRI9qRaUJficCshMzZz/kqSIR/hRkY6uecB0A=
=CCqs
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
Merge "i.MX device tree changes for 3.15" from Shawn Guo:
- New SoC device tree support for imx35 and imx50
- A good number of new board support: imx25-eukrea, imx28-duckbill,
imx28-eukrea, Eukrea cpuimx35, imx50-evk, imx51-eukrea, imx53-voipac,
MCIMX53-START-R and Ka-Ro TX53.
- Quite some updates and tweaking on imx27 phycore and apf27dev boards
- Add pinfunc headers for imx25, imx27 and imx50
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Use clock defines in imx5 DTS files
- Use macros for interrupt and gpio flags
- A plenty of random updates on various SoC and board device tree
sources, adding pinctrl settings, device nodes, properties, aliases.
* tag 'imx-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (89 commits)
ARM: dts: imx28-m28cu3: Remove 'reset-active-high'
ARM: dts: imx5: use imx51-ssi
ARM: dts: imx51: Add mmc aliases
ARM: dts: imx53: Add mmc aliases
ARM: dts: imx53: add support for Ka-Ro TX53 modules
ARM: dts: Add support for the cpuimx35 board from Eukrea and its baseboard.
ARM: dts: imx28-apf28dev: add user button
ARM: dts: i.MX51: Switch to use standard definitions for input subsystem
ARM: dts: i.MX53: add support for MCIMX53-START-R
ARM: dts: i.MX53: move common QSB nodes to new file
ARM: dts: imx53-evk: Remove board support
ARM: dts: vf610: use the interrupt macros
ARM: dts: imx53: Add gpio and input dt includes.
ARM: dts: i.MX27: Add SSI nodes
ARM: dts: mxs: add mxs phy controller id
ARM: dts: imx27-phytec-phycore-rdk: Add pinctrl definitions for WEIM
ARM: dts: imx27-phytec-phycore-rdk: Add pingrp for SDHC
ARM: dts: imx27-phytec-phycore-som: Add spi-cs-high property to PMIC
ARM: dts: imx27-phytec-phycore-rdk: Enable 1-Wire module
ARM: dts: imx27-phytec-phycore-som: Add NFC pin group
...
- A good number of new i.MX6 boards support: cm-fx6, dmo-edmqmx6,
nitrogen6x, Gateworks Ventana gw5xxx family, DFI FS700-M60 and
Zealz GK802
- Update imx6q-sabrelite device tree and add Dual Lite/Solo support
- Move pins that are used by particular client device out of hog group
- Use GPIO_6 for FEC interrupt to workaround a hardware bug (ERR006687
ENET: Only the ENET wake-up interrupt request can wake the system
from Wait mode.)
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Update OPP table for cpufreq support
- Random updates on various board device tree sources, adding pinctrl
settings, device nodes, properties, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJS+I4nAAoJEFBXWFqHsHzO39AIALs0nns7ew/KyO4brtDP/gpA
dgTtpD5+eiddSng41aTun0WzUp/4r9iNL79lBfSUYJpo7+ZaQwpSlPbTz1wUMGtr
mINmTXNXHHLCufm8ywQMYrajF+wQKXEMAJ7/OLyxFzQTwsKW9OWr4DLiTgvVLuKs
IOD9scHe2KNRFJjfPmaS5w5W4h+Xs2VJO4mmCmy7zFgQ8MvIGpKGBZ3k3Y/c0Vqq
w8VjL2RPnK9Q8C4sjweP7QRvdnFyn4ClVTPGFQ8c/xs7QqC7cVIc6FSqlXAvWVmx
lnKv4y9+J4RyVGvQi9KwyscpEx1aD5xJv5hwl0MeoN8Kas9qhSfP9KfqWc9fL9I=
=tiCP
-----END PGP SIGNATURE-----
Merge tag 'imx6-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6 into next/dt
Merge "i.MX6 device tree changes for 3.15" from Shawn Guo:
- A good number of new i.MX6 boards support: cm-fx6, dmo-edmqmx6,
nitrogen6x, Gateworks Ventana gw5xxx family, DFI FS700-M60 and
Zealz GK802
- Update imx6q-sabrelite device tree and add Dual Lite/Solo support
- Move pins that are used by particular client device out of hog group
- Use GPIO_6 for FEC interrupt to workaround a hardware bug (ERR006687
ENET: Only the ENET wake-up interrupt request can wake the system
from Wait mode.)
- Make pinctrl nodes board specific to avoid floating board specific
device tree blob with so many unused pinctrl data
- Use generic node name for fixed regulator
- Update OPP table for cpufreq support
- Random updates on various board device tree sources, adding pinctrl
settings, device nodes, properties, etc.
* tag 'imx6-dt-3.15' of git://git.linaro.org/people/shawnguo/linux-2.6: (62 commits)
ARM: dts: imx6q: Add support for Zealz GK802
ARM: dts: imx6: Add DFI FS700-M60 board support
ARM: dts: imx6: use imx51-ssi
ARM: dts: imx6qdl: Add mmc aliases
ARM: dts: imx6q: Add spi4 alias
ARM: dts: imx6qdl-sabreauto: Add LVDS support
ARM: dts: imx6sl: add keypad support for i.mx6sl-evk board.
ARM: dts: imx6sl: add ocram device support
ARM: dts: imx6qdl: enable dma for spi
ARM: dts: imx6qdl-sabresd: Add PFUZE100 support
ARM: dts: imx6: add mxs phy controller id
ARM: dts: imx6: add anatop phandle for usbphy
ARM: dts: imx6q-arm2: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl-sabreauto: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC interrupt.
ARM: dts: imx6qdl: use interrupts-extended for fec
ARM: dts: imx: pinfunc: add MX6QDL_PAD_GPIO_6__ENET_IRQ
ARM: dts: imx6q-sabrelite: PHY reset is active-low
ARM: dts: imx6: Use 'vddarm' as the regulator name
ARM: dts: imx6qdl-sabresd: Add power key support
...
Pull the functionality which is required to cleanup sdhci/sdio
in. It's in a separate branch so it can be pulled from others
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Qualcomm Universal Peripheral (QUP) core is an
AHB slave that provides a common data path (an output
FIFO and an input FIFO) for serial peripheral interface
(SPI) mini-core.
Signed-off-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=g6PN
-----END PGP SIGNATURE-----
Merge tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux into next/cleanup
This cleanup series gets rid of <mach/timex.h> for platforms not using
ARCH_MULTIPLATFORM. (For multi-platform code it's already unused since
387798b (ARM: initial multiplatform support).)
To make this work some code out of arch/arm needed to be adapted. The
respective changes got acks by their maintainers to be taken via armsoc
(with Andrew Morton substituting for Alessandro Zummo as rtc maintainer).
Compared to the previous pull request there was another patch added that
fixes a (non-critical) regression on ixp4xx. Olof Johansson asked to not
squash this fix into the original commit to save him from the need to
reverify the series.
* tag 'dropmachtimexh-v2' of git://git.pengutronix.de/git/ukl/linux:
ARM: ixp4xx: fix timer latch calculation
ARM: drop <mach/timex.h> for !ARCH_MULTIPLATFORM, too
ARM: rpc: stop using <mach/timex.h>
ARM: ixp4xx: stop using <mach/timex.h>
input: ixp4xx-beeper: don't use symbols from <mach/timex.h>
ARM: at91: don't use <mach/timex.h>
ARM: ep93xx: stop using mach/timex.h
ARM: mmp: stop using mach/timex.h
ARM: netx: stop using mach/timex.h
ARM: sa1100: stop using mach/timex.h
clocksource: sirf/marco+prima2: drop usage of CLOCK_TICK_RATE
rtc: pxa: drop unused #define TIMER_FREQ
rtc: at91sam9: include <mach/hardware.h> explicitly
ARM/serial: at91: switch atmel serial to use gpiolib
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull networking fixes from David Miller:
1) kvaser CAN driver has fixed limits of some of it's table, validate
that we won't exceed those limits at probe time. Fix from Olivier
Sobrie.
2) Fix rtl8192ce disabling interrupts for too long, from Olivier
Langlois.
3) Fix botched shift in ath5k driver, from Dan Carpenter.
4) Fix corruption of deferred packets in TIPC, from Erik Hugne.
5) Fix newlink error path in macvlan driver, from Cong Wang.
6) Fix netpoll deadlock in bonding, from Ding Tianhong.
7) Handle GSO packets properly in forwarding path when fragmentation is
necessary on egress, from Florian Westphal.
8) Fix axienet build errors, from Michal Simek.
9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
Tsirkin.
10) Carrier status isn't set properly in hyperv driver, from Haiyang
Zhang.
11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.
12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
queue selection method. Add a fallback method mechanism to fix this
bug, from Daniel Borkmann.
13) Fix regression in link local route handling on GRE tunnels, from
Nicolas Dichtel.
14) Bonding can assign dup aggregator IDs in some sequences of
configuration, fix by making the allocation counter per-bond instead
of global. From Jiri Bohac.
15) sctp_connectx() needs compat translations, from Daniel Borkmann.
16) Fix of_mdio PHY interrupt parsing, from Ben Dooks
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
MAINTAINERS: add entry for the PHY library
of_mdio: fix phy interrupt passing
net: ethernet: update dependency and help text of mvneta
NET: fec: only enable napi if we are successful
af_packet: remove a stray tab in packet_set_ring()
net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
ipv4: fix counter in_slow_tot
irtty-sir.c: Do not set_termios() on irtty_close()
bonding: 802.3ad: make aggregator_identifier bond-private
usbnet: remove generic hard_header_len check
gre: add link local route when local addr is any
batman-adv: fix potential kernel paging error for unicast transmissions
batman-adv: avoid double free when orig_node initialization fails
batman-adv: free skb on TVLV parsing success
batman-adv: fix TT CRC computation by ensuring byte order
batman-adv: fix potential orig_node reference leak
batman-adv: avoid potential race condition when adding a new neighbour
batman-adv: properly check pskb_may_pull return value
batman-adv: release vlan object after checking the CRC
batman-adv: fix TT-TVLV parsing on OGM reception
...
This patch fixes a typo in the Device Tree binding for the
leading '#'.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of the device tree probing for the Renesas SH-Mobile SoCs
documenting the device tree binding as necessary.
This work is loosely based on the original patch by Nobuhiro Iwamatsu
<nobuhiro.iwamatsu.yj@renesas.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The clk-phase property is used to represent the 2 clock phase values that is
needed for the SD/MMC driver. Add a prepare function to the clk_ops, that will
use the syscon driver to set sdmmc_clk's phase shift that is located in the
system manager.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
---
v9: none
v8: Use degrees in the clk-phase binding property
v7: Add dts property to represent the clk phase of the sdmmc_clk. Add a
prepare function to the gate clk that will toggle clock phase setting.
Remove the "altr,socfpga-sdmmc-sdr-clk" clock type.
v6: Add a new clock type "altr,socfpga-sdmmc-sdr-clk" that will be used to
set the phase shift settings.
v5: Use the "snps,dw-mshc" binding
v4: Use the sdmmc_clk prepare function to set the phase shift settings
v3: Not use the syscon driver because as of 3.13-rc1, the syscon driver is
loaded after the clock driver.
v2: Use the syscon driver
This patch is an attempt to gather the Ethernet related bindings in one file,
like it's done in the MMC and some other subsystems. It should save some of
the trouble of documenting several properties over and over in each binding
document, instead only making reference to the main file.
I have used the Embedded Power Architecture(TM) Platform Requirements (ePAPR)
standard as a base for the properties description, also documenting some ad-hoc
properties that have been introduced over time despite having direct analogs in
ePAPR.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a correction to the documentation. It was previously required but not documented.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add dma support for lpuart. This function depend on DMA driver.
You can turn on it by write both the dmas and dma-name properties in dts node.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/memory
and fix the header file includes.
Also remove module_platform_driver() and instead call
platform_driver_register() from subsys_initcall() to make sure this module
has been loaded before MTD partition parsing starts.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Add compatibles
matching the other pattern to the clock driver for consistency, and keep the
older one for backward compatibility.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The Allwinner A20/A31 clock module controls the transmit clock source
and interface type of the GMAC ethernet controller. Model this as
a single clock for GMAC drivers to use.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
The A31 has a slightly different PLL6 clock. Add support for this new clock in
our driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Add register definitions for the usb-clk register found on sun4i, sun5i and
sun7i SoCs.
Signed-off-by: Roman Byshko <rbyshko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
imx25 did not work without a firmware previously.
This patch adds a DT compatible to pass the correct data with the
default script addresses for imx25.
Add imx25 compatible to the list of compatibles in the binding
documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Add Freescale enhanced direct memory(eDMA) controller support.
This module can be found on Vybrid and LS-1 SoCs.
Signed-off-by: Alison Wang <b18965@freescale.com>
Signed-off-by: Jingchang Lu <b35083@freescale.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Document the required "clocks" phandles and their corresponding
"clock-names" properties for the two clocks used by the GENET hardware
block ("enet" and "enet-wol").
CC: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the binding information for the gating clocks of the Armada 380
SoCs and the Armada 385 SoCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the binding information for the core clocks of the Armada 380 and
Armada 385 SoCs
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the binding information for the gating clocks of the Armada 375 SoCs
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add the binding information for the core clocks of the Armada 375 SoCs
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Freescale DSPI module will have two endianess in different platform,
but ARM is little endian. So when DSPI in big endian, core in little endian,
readl and writel can not adjust R/W register in this condition.
This patch will remove general readl/writel, and import regmap mechanism.
Data endian will be transfered in regmap APIs.
Documents: dspi add bool "big-endian" in dts node if DSPI module
work in big endian.
Signed-off-by: Chao Fu <b44548@freescale.com>
Reviewed-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=DDj5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Kevin Hilman:
"A collection of ARM SoC fixes for v3.14-rc1.
Mostly a collection of Kconfig, device tree data and compilation fixes
along with fix to drivers/phy that fixes a boot regression on some
Marvell mvebu platforms"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
dma: mv_xor: Silence a bunch of LPAE-related warnings
ARM: ux500: disable msp2 device tree node
ARM: zynq: Reserve not DMAable space in front of the kernel
ARM: multi_v7_defconfig: Select CONFIG_SOC_DRA7XX
ARM: imx6: Initialize low-power mode early again
ARM: pxa: fix various compilation problems
ARM: pxa: fix compilation problem on AM300EPD board
ARM: at91: add Atmel's SAMA5D3 Xplained board
spi/atmel: document clock properties
mmc: atmel-mci: document clock properties
ARM: at91: enable USB host on at91sam9n12ek board
ARM: at91/dt: fix sama5d3 ohci hclk clock reference
ARM: at91/dt: sam9263: fix compatibility string for the I2C
ata: sata_mv: Fix probe failures with optional phys
drivers: phy: Add support for optional phys
drivers: phy: Make NULL a valid phy reference
ARM: fix HAVE_ARM_TWD selection for OMAP and shmobile
ARM: moxart: move DMA_OF selection to driver
ARM: hisi: fix kconfig warning on HAVE_ARM_TWD
This brings the xhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
postfix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.
Note that the old xhci-platform compatible string is kept around for, well,
compatibility reasons.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This brings the uhci-platform bindings in sync with what we've done for
the ohci- and ehci-platform drivers. As discussed there using platform as a
prefix is a bit weird as the platform bus is a Linux specific thing and
the bindings are supposed to be OS agnostic.
Note that the old platform-uhci compatible string is kept around for, well,
compatibility reasons.
While at it rename the bindings txt file to match the name of all the
other ?hci-platform bindings docs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clock names mistakenly given opposite. This patch fix this issue.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds pmusysreg node to exynos5250 and exynos5420 dtsi files to
handle PMU register accesses in a centralized way using syscon driver
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Allwinner A10 compatibles were following a slightly different compatible
patterns than the rest of the SoCs for historical reasons. Change the compatibles
to match the other pattern in the SID driver for consistency.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds a simple ASoC board driver fo the Armada 370
Development Board, which connects the audio unit of the Armada 370 SoC
to the I2C-based CS42L51.
For now, only the analog audio input and output through the CS42L51
are supported, but a followup patch adds S/PDIF support to this
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Update the compatible string for Overo/Tobi to reflect the latest
changes.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds the Device Tree bindings for the Broadcom GENET Gigabit
Ethernet controller. A bunch of examples are provided to illustrate the
versatile aspect of the hardare.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlL7RxcACgkQjTAFq1RaXHNcKACgk4Vj+1KlmWVEin8VPoJBX86m
RasAn36pSY1OszxypJOF0O1s0qO9ld5K
=383M
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-3.15-20140212' of git://gitorious.org/linux-can/linux-can-next
linux-can-next-for-3.15-20140212
Marc Kleine-Budde says:
====================
this is a pull request of eight patches for net-next/master.
Florian Vaussard contributed a series that merged the sja1000 of_platform
into the platform driver. The of_platform driver is finally removed.
Stephane Grosjean supplied a patch to allocate CANFD skbs. In a patch
by Uwe Kleine-König another missing copyright information was added to
a userspace header. And a patch by Yoann DI RUZZA that adds listen only
mode to the at91_can driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the devicetree documentation for the Maxim MAX310X UARTs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the -generic suffix from the compatible string in the serial port
DT bindings example.
Cc: devicetree@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This atomic commit changes the Integrator clock implementation
and the machines to register clocks from the device tree and
use these instead of the previous hard-coded clocks.
In the clock implementation all hard-coded clocks and the
special initialization function call goes away, and is
replaced by two compatible strings for the two clocks
available on the core module.
Cc: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the option to choose clock on which pin input to SSC (as slave).
Default is on TK pin to SSC, add "atmel,clk-from-rk-pin" option to
specify the clock is on RK pin to SSC.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and ESAI device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the ESAI
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For most platforms, the CPU and SPDIF device is in the same endianess
mode. While for the LS1 platform, the CPU is in LE mode and the SPDIF
is in BE mode.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
gpios-states is array, and default is 0
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=nSiE
-----END PGP SIGNATURE-----
Merge tag 'iio-for-3.15a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new drivers and cleanups for IIO in the 3.15 cycle.
New drivers:
* si7005 relative humidity and temperature sensor
* Lite-on ltr501 ambient light and proximity sensor
Cleanups
* Clean up some dead comments in max1363
* Drop some obsolete variables in adjd_s311 and tcs3472 left over from
the introduction of iio_push_to_buffers_with_timestamp.
* Drop some unneeded linux/init.h includes
* Squish a sparse warning in mpl3115 by correctly specifying a be32 variable.
* A number of cleanups and fixes for sca3000
* Drop an unneed checks in mxs-lradc, ad7303 and adis16400.
* Drop a platform_set_drvdata in viperboard after the only use of it was
removed during a devm conversion.
* Add a missing device name for ak8975 to comply with the ABI.
* Put mpu6050 into the IMU menu as it slipped out into the main menu.
* Fix a typo and some comment formatting in mpu6050.
* Document at91 ADC clock properties.
The initial versions of the devicetree enablement patches for ehci-platform
used "ehci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up, added a:
"depends on !PPC_OF" to Kconfig to avoid a known conflict with PPC-OF platforms
and went with the generic usb-ehci as requested.
In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ehci", ie they have:
compatible = "ti,ehci-omap", "usb-ehci";
In theory this should not be a problem since the "ti,ehci-omap" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.
This patch changes the compatible string claimed by ehci-platform to
"generic-ehci", avoiding the driver registration / module loading ordering
problems, and removes the "depends on !PPC_OF" workaround.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The initial versions of the devicetree enablement patches for ohci-platform
used "ohci-platform" as compatible string. However this was disliked by various
reviewers because the platform bus is a Linux invention and devicetree is
supposed to be OS agnostic. After much discussion I gave up and went with
the generic usb-ohci as requested.
In retro-spect I should have chosen something different, the dts files for many
existing boards already claim to be compatible with "usb-ohci", ie they have:
compatible = "ti,ohci-omap3", "usb-ohci";
In theory this should not be a problem since the "ti,ohci-omap3" entry takes
presedence, but in practice using a conflicting compatible string is an issue,
because it makes which driver gets used depend on driver registration order.
This patch changes the compatible string claimed by ohci-platform to
"generic-ohci", avoiding the driver registration / module loading ordering
problems.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The saw2 binding describes the SPM/AVS wrapper hardware used to
control the regulator supplying voltage to the Krait CPUs.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
The kpss acc binding describes the clock, reset, and power domain
controller for a Krait CPU.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Scorpion and Krait don't use the spin-table enable-method.
Instead they rely on mmio register accesses to enable power and
clocks to bring CPUs out of reset. Document their enable-methods.
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Rohit Vaswani <rvaswani@codeaurora.org>
[sboyd: Split off into separate patch, renamed methods to
match compatible nodes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
- Fix compile error drivers/spi/spi-rspi.c with !CONFIG_OF
- Fix warnings for unused/uninitialized variables with !CONFIG_OF
- Fix PCIe bus matching for powerpc
- Add documentation for various vendor strings
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJS+kY1AAoJEMhvYp4jgsXiEo8IAIHD4+QSyVpHEYnhlyDPPGxt
zQHj/jadofP7nsC0QgFhTnmG1qEUjl8BZ5UsA+swaixtqFkKdsGtCtQ+c/PCU8LK
OHTZ2XbT+TTkyKncx+Beghb/v2e8AVGutlSoFGpsGK/nuvda950VoKsH2eVE1X0c
9YBy209/g+nNcaC+qNwuBL4acy9bQmyj/Pm//5lMzv0VU7uGVE8hl6Eh6kpd847g
Ww26c/fK0JL3yQBYxbhAupuwXieY6wbZ1u1c/37EloMv6ahsT1v+iFaWJun35KeT
xyKYgw7tDDcrVEiNfg6jhEYyG2PmDVEvouEafy60ha+iHuQxHp1psrc4zVS9Xn8=
=bkhj
-----END PGP SIGNATURE-----
Merge tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree fixes from Rob Herring:
- Fix compile error drivers/spi/spi-rspi.c with !CONFIG_OF
- Fix warnings for unused/uninitialized variables with !CONFIG_OF
- Fix PCIe bus matching for powerpc
- Add documentation for various vendor strings
* tag 'dt-fixes-for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
DT: Add vendor prefix for Spansion Inc.
of/device: Nullify match table in of_match_device() for CONFIG_OF=n
dt-bindings: add vendor-prefix for neonode
of: fix PCI bus match for PCIe slots
of: restructure for_each macros to fix compile warnings
of: add vendor prefix for Honeywell
of: Update qcom vendor prefix description
of: add vendor prefix for Allwinner Technology
Pull networking updates from David Miller:
1) Fix flexcan build on big endian, from Arnd Bergmann
2) Correctly attach cpsw to GPIO bitbang MDIO drive, from Stefan Roese
3) udp_add_offload has to use GFP_ATOMIC since it can be invoked from
non-sleepable contexts. From Or Gerlitz
4) vxlan_gro_receive() does not iterate over all possible flows
properly, fix also from Or Gerlitz
5) CAN core doesn't use a proper SKB destructor when it hooks up
sockets to SKBs. Fix from Oliver Hartkopp
6) ip_tunnel_xmit() can use an uninitialized route pointer, fix from
Eric Dumazet
7) Fix address family assignment in IPVS, from Michal Kubecek
8) Fix ath9k build on ARM, from Sujith Manoharan
9) Make sure fail_over_mac only applies for the correct bonding modes,
from Ding Tianhong
10) The udp offload code doesn't use RCU correctly, from Shlomo Pongratz
11) Handle gigabit features properly in generic PHY code, from Florian
Fainelli
12) Don't blindly invoke link operations in
rtnl_link_get_slave_info_data_size, they are optional. Fix from
Fernando Luis Vazquez Cao
13) Add USB IDs for Netgear Aircard 340U, from Bjørn Mork
14) Handle netlink packet padding properly in openvswitch, from Thomas
Graf
15) Fix oops when deleting chains in nf_tables, from Patrick McHardy
16) Fix RX stalls in xen-netback driver, from Zoltan Kiss
17) Fix deadlock in mac80211 stack, from Emmanuel Grumbach
18) inet_nlmsg_size() forgets to consider ifa_cacheinfo, fix from Geert
Uytterhoeven
19) tg3_change_mtu() can deadlock, fix from Nithin Sujir
20) Fix regression in setting SCTP local source addresses on accepted
sockets, caused by some generic ipv6 socket changes. Fix from
Matija Glavinic Pecotic
21) IPPROTO_* must be pure defines, otherwise module aliases don't get
constructed properly. Fix from Jan Moskyto
22) IPV6 netconsole setup doesn't work properly unless an explicit
source address is specified, fix from Sabrina Dubroca
23) Use __GFP_NORETRY for high order skb page allocations in
sock_alloc_send_pskb and skb_page_frag_refill. From Eric Dumazet
24) Fix a regression added in netconsole over bridging, from Cong Wang
25) TCP uses an artificial offset of 1ms for SRTT, but this doesn't jive
well with TCP pacing which needs the SRTT to be accurate. Fix from
Eric Dumazet
26) Several cases of missing header file includes from Rashika Kheria
27) Add ZTE MF667 device ID to qmi_wwan driver, from Raymond Wanyoike
28) TCP Small Queues doesn't handle nonagle properly in some corner
cases, fix from Eric Dumazet
29) Remove extraneous read_unlock in bond_enslave, whoops. From Ding
Tianhong
30) Fix 9p trans_virtio handling of vmalloc buffers, from Richard Yao
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (136 commits)
6lowpan: fix lockdep splats
alx: add missing stats_lock spinlock init
9p/trans_virtio.c: Fix broken zero-copy on vmalloc() buffers
bonding: remove unwanted bond lock for enslave processing
USB2NET : SR9800 : One chip USB2.0 USB2NET SR9800 Device Driver Support
tcp: tsq: fix nonagle handling
bridge: Prevent possible race condition in br_fdb_change_mac_address
bridge: Properly check if local fdb entry can be deleted when deleting vlan
bridge: Properly check if local fdb entry can be deleted in br_fdb_delete_by_port
bridge: Properly check if local fdb entry can be deleted in br_fdb_change_mac_address
bridge: Fix the way to check if a local fdb entry can be deleted
bridge: Change local fdb entries whenever mac address of bridge device changes
bridge: Fix the way to find old local fdb entries in br_fdb_change_mac_address
bridge: Fix the way to insert new local fdb entries in br_fdb_changeaddr
bridge: Fix the way to find old local fdb entries in br_fdb_changeaddr
tcp: correct code comment stating 3 min timeout for FIN_WAIT2, we only do 1 min
net: vxge: Remove unused device pointer
net: qmi_wwan: add ZTE MF667
3c59x: Remove unused pointer in vortex_eisa_cleanup()
net: fix 'ip rule' iif/oif device rename
...
This patch replaces custom lcd_power() callback with
regulator API over LCD class.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The audio unit found in the Armada 370 SoC is similar to the one used
in the Marvell Kirkwood and Marvell Dove SoCs. Therefore, this commit
allows the Kirkwood audio driver to be built on mvebu platforms, and
adds an additional compatible string to identify the Armada 370
variant of the audio unit.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This commit adds a trivial Device Tree binding to the I2C-based
cs42l51 sound codec, so that it can be used from Device Tree based
platforms.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adds pinctrl support for all platforms based on EXYNOS5260 SoC.
Acked-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Young-Gun Jang <yg1004.jang@samsung.com>
Signed-off-by: Rahul Sharma <rahul.sharma@samsung.com>
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some of the 00-INDEX files are somewhat outdated and some folders does
not contain 00-INDEX at all. Only outdated (with the notably exception
of spi) indexes are touched here, the 169 folders without 00-INDEX has
not been touched.
New 00-INDEX
- spi/* was added in a series of commits dating back to 2006
Added files (missing in (*/)00-INDEX)
- dmatest.txt was added by commit 851b7e16a0 ("dmatest: run test via
debugfs")
- this_cpu_ops.txt was added by commit a1b2a555d6 ("percpu: add
documentation on this_cpu operations")
- ww-mutex-design.txt was added by commit 040a0a3710 ("mutex: Add
support for wound/wait style locks")
- bcache.txt was added by commit cafe563591 ("bcache: A block layer
cache")
- kernel-per-CPU-kthreads.txt was added by commit 49717cb404
("kthread: Document ways of reducing OS jitter due to per-CPU
kthreads")
- phy.txt was added by commit ff76496347 ("drivers: phy: add generic
PHY framework")
- block/null_blk was added by commit 12f8f4fc03 ("null_blk:
documentation")
- module-signing.txt was added by commit 3cafea3076 ("Add
Documentation/module-signing.txt file")
- assoc_array.txt was added by commit 3cb989501c ("Add a generic
associative array implementation.")
- arm/IXP4xx was part of the initial repo
- arm/cluster-pm-race-avoidance.txt was added by commit 7fe31d28e8
("ARM: mcpm: introduce helpers for platform coherency exit/setup")
- arm/firmware.txt was added by commit 7366b92a77 ("ARM: Add
interface for registering and calling firmware-specific operations")
- arm/kernel_mode_neon.txt was added by commit 2afd0a0524 ("ARM:
7825/1: document the use of NEON in kernel mode")
- arm/tcm.txt was added by commit bc581770cf ("ARM: 5580/2: ARM TCM
(Tightly-Coupled Memory) support v3")
- arm/vlocks.txt was added by commit 9762f12d3e ("ARM: mcpm: Add
baremetal voting mutexes")
- blackfin/gptimers-example.c, Makefile was added by commit
4b60779d5e ("Blackfin: add an example showing how to use the
gptimers API")
- devicetree/usage-model.txt was added by commit 31134efc68 ("dt:
Linux DT usage model documentation")
- fb/api.txt was added by commit fb21c2f428 ("fbdev: Add FOURCC-based
format configuration API")
- fb/sm501.txt was added by commit e6a0498071 ("video, sm501: add
edid and commandline support")
- fb/udlfb.txt was added by commit 96f8d864af ("fbdev: move udlfb out
of staging.")
- filesystems/Makefile was added by commit 1e0051ae48
("Documentation/fs/: split txt and source files")
- filesystems/nfs/nfsd-admin-interfaces.txt was added by commit
8a4c6e19cf ("nfsd: document kernel interfaces for nfsd
configuration")
- ide/warm-plug-howto.txt was added by commit f74c91413e ("ide: add
warm-plug support for IDE devices (take 2)")
- laptops/Makefile was added by commit d49129accc
("Documentation/laptop/: split txt and source files")
- leds/leds-blinkm.txt was added by commit b54cf35a7f ("LEDS: add
BlinkM RGB LED driver, documentation and update MAINTAINERS")
- leds/ledtrig-oneshot.txt was added by commit 5e417281cd ("leds: add
oneshot trigger")
- leds/ledtrig-transient.txt was added by commit 44e1e9f8e7 ("leds:
add new transient trigger for one shot timer activation")
- m68k/README.buddha was part of the initial repo
- networking/LICENSE.(qla3xxx|qlcnic|qlge) was added by commits
40839129f7, c4e84bde1d, 5a4faa8737
- networking/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- networking/i40evf.txt was added by commit 105bf2fe6b ("i40evf: add
driver to kernel build system")
- networking/ipsec.txt was added by commit b3c6efbc36 ("xfrm: Add
file to document IPsec corner case")
- networking/mac80211-auth-assoc-deauth.txt was added by commit
3cd7920a2b ("mac80211: add auth/assoc/deauth flow diagram")
- networking/netlink_mmap.txt was added by commit 5683264c39
("netlink: add documentation for memory mapped I/O")
- networking/nf_conntrack-sysctl.txt was added by commit c9f9e0e159
("netfilter: doc: add nf_conntrack sysctl api documentation") lan)
- networking/team.txt was added by commit 3d249d4ca7 ("net: introduce
ethernet teaming device")
- networking/vxlan.txt was added by commit d342894c5d ("vxlan:
virtual extensible lan")
- power/runtime_pm.txt was added by commit 5e928f77a0 ("PM: Introduce
core framework for run-time PM of I/O devices (rev. 17)")
- power/charger-manager.txt was added by commit 3bb3dbbd56
("power_supply: Add initial Charger-Manager driver")
- RCU/lockdep-splat.txt was added by commit d7bd2d68aa ("rcu:
Document interpretation of RCU-lockdep splats")
- s390/kvm.txt was added by 5ecee4b (KVM: s390: API documentation)
- s390/qeth.txt was added by commit b4d72c08b3 ("qeth: bridgeport
support - basic control")
- scheduler/sched-bwc.txt was added by commit 88ebc08ea9 ("sched: Add
documentation for bandwidth control")
- scsi/advansys.txt was added by commit 4bd6d7f356 ("[SCSI] advansys:
Move documentation to Documentation/scsi")
- scsi/bfa.txt was added by commit 1ec90174bd ("[SCSI] bfa: add
readme file")
- scsi/bnx2fc.txt was added by commit 12b8fc10ea ("[SCSI] bnx2fc: Add
driver documentation")
- scsi/cxgb3i.txt was added by commit c3673464eb ("[SCSI] cxgb3i: Add
cxgb3i iSCSI driver.")
- scsi/hpsa.txt was added by commit 992ebcf14f ("[SCSI] hpsa: Add
hpsa.txt to Documentation/scsi")
- scsi/link_power_management_policy.txt was added by commit
ca77329fb7 ("[libata] Link power management infrastructure")
- scsi/osd.txt was added by commit 78e0c621de ("[SCSI] osd:
Documentation for OSD library")
- scsi/scsi-parameter.txt was created/moved by commit 163475fb11
("Documentation: move SCSI parameters to their own text file")
- serial/driver was part of the initial repo
- serial/n_gsm.txt was added by commit 323e84122e ("n_gsm: add a
documentation")
- timers/Makefile was added by commit 3794f3e812 ("docsrc: build
Documentation/ sources")
- virt/kvm/s390.txt was added by commit d9101fca3d ("KVM: s390:
diagnose call documentation")
- vm/split_page_table_lock was added by commit 49076ec2cc ("mm:
dynamically allocate page->ptl if it cannot be embedded to struct
page")
- w1/slaves/w1_ds28e04 was added by commit fbf7f7b4e2 ("w1: Add
1-wire slave device driver for DS28E04-100")
- w1/masters/omap-hdq was added by commit e0a29382c6 ("hdq:
documentation for OMAP HDQ")
- x86/early-microcode.txt was added by commit 0d91ea86a8 ("x86, doc:
Documentation for early microcode loading")
- x86/earlyprintk.txt was added by commit a1aade4788 ("x86/doc:
mini-howto for using earlyprintk=dbgp")
- x86/entry_64.txt was added by commit 8b4777a4b5 ("x86-64: Document
some of entry_64.S")
- x86/pat.txt was added by commit d27554d874 ("x86: PAT
documentation")
Moved files
- arm/kernel_user_helpers.txt was moved out of arch/arm/kernel by
commit 37b8304642 ("ARM: kuser: move interface documentation out of
the source code")
- efi-stub.txt was moved out of x86/ and down into Documentation/ in
commit 4172fe2f8a ("EFI stub documentation updates")
- laptops/hpfall.c was moved out of hwmon/ and into laptops/ in commit
efcfed9bad ("Move hp_accel to drivers/platform/x86")
- commit 5616c23ad9 ("x86: doc: move x86-generic documentation from
Doc/x86/i386"):
* x86/usb-legacy-support.txt
* x86/boot.txt
* x86/zero_page.txt
- power/video_extension.txt was moved to acpi in commit 70e66e4df1
("ACPI / video: move video_extension.txt to Documentation/acpi")
Removed files (left in 00-INDEX)
- memory.txt was removed by commit 00ea8990aa ("memory.txt: remove
stray information")
- gpio.txt was moved to gpio/ in commit fd8e198cfc ("Documentation:
gpiolib: document new interface")
- networking/DLINK.txt was removed by commit 168e06ae26
("drivers/net: delete old parallel port de600/de620 drivers")
- serial/hayes-esp.txt was removed by commit f53a2ade0b ("tty: esp:
remove broken driver")
- s390/TAPE was removed by commit 9e280f6693 ("[S390] remove tape
block docu")
- vm/locking was removed by commit 57ea8171d2 ("mm: documentation:
remove hopelessly out-of-date locking doc")
- laptops/acer-wmi.txt was remvoed by commit 020036678e ("acer-wmi:
Delete out-of-date documentation")
Typos/misc issues
- rpc-server-gss.txt was added as knfsd-rpcgss.txt in commit
030d794bf4 ("SUNRPC: Use gssproxy upcall for server RPCGSS
authentication.")
- commit b88cf73d92 ("net: add missing entries to
Documentation/networking/00-INDEX")
* generic-hdlc.txt was added as generic_hdlc.txt
* spider_net.txt was added as spider-net.txt
- w1/master/mxc-w1 was added as mxc_w1 by commit a5fd9139f7 ("w1: add
1-wire master driver for i.MX27 / i.MX31")
- s390/zfcpdump.txt was added as zfcpdump by commit 6920c12a40
("[S390] Add Documentation/s390/00-INDEX.")
Signed-off-by: Henrik Austad <henrik@austad.us>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> [rcu bits]
Acked-by: Rob Landley <rob@landley.net>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Len Brown <len.brown@intel.com>
Cc: James Bottomley <JBottomley@parallels.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This add the following three new properties documenting and usage
for simple card:
"simple-audio-card,name",
"simple-audio-card,widgets",
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The clkc has its registers in the range of the slcr.
Instead of passing around the slcr base address pointer, let the clkc get the
address from the DT.
This prepares the slcr to be a real driver with multiple memory ranges
(slcr, clocks, pinctrl,...)
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For some silicons, the pin configuration register can control
the output of the pin when the pad including the pin enter
low power mode.
For example, the pin can be "Drive 1", "Drive 0", "Float" when
the pad including the pin enter low power mode.
It is very useful when you want to control the power leakeage
when the SOC enter low power mode, and can save more power for
the low power mode.
Signed-off-by: Chao Xie <chao.xie@marvell.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch add interrupt support to the pincontroller driver.
ST Pincontroller GPIO bank can have one of the two possible types of
interrupt-wirings.
First type is via irqmux, single interrupt is used by multiple gpio
banks. This reduces number of overall interrupts numbers required. All
these banks belong to a single pincontroller.
_________
| |----> [gpio-bank (n) ]
| |----> [gpio-bank (n + 1)]
[irqN]-- | irq-mux |----> [gpio-bank (n + 2)]
| |----> [gpio-bank (... )]
|_________|----> [gpio-bank (n + 7)]
Second type has a dedicated interrupt per gpio bank.
[irqN]----> [gpio-bank (n)]
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Note this commit uses the same devicetree booleans for this as the ones
already existing in the usb-ehci bindings, see:
Documentation/devicetree/bindings/usb/usb-ehci.txt
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently ehci-platform is only used in combination with devicetree when used
with some Via socs. By extending it to (optionally) get clks and a phy from
devicetree, and enabling / disabling those on power_on / off, it can be used
more generically. Specifically after this commit it can be used for the
ehci controller on Allwinner sunxi SoCs.
Since ehci-platform is intended to handle any generic enough non pci ehci
device, add a "usb-ehci" compatibility string.
There already is a usb-ehci device-tree bindings document, update this
with clks and phy bindings info.
Although actually quite generic so far the via,vt8500 compatibilty string
had its own bindings document. Somehow we even ended up with 2 of them. Since
these provide no extra information over the generic usb-ehci documentation,
this patch removes them.
The ehci-ppc-of.c driver also claims the usb-ehci compatibility string,
even though it mostly is ibm,usb-ehci-440epx specific. ehci-platform.c is
not needed on ppc platforms, so add a !PPC_OF dependency to it to avoid
2 drivers claiming the same compatibility string getting build on ppc.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for ohci-platform instantiation from devicetree, including
optionally getting clks and a phy from devicetree, and enabling / disabling
those on power_on / off.
This should allow using ohci-platform from devicetree in various cases.
Specifically after this commit it can be used for the ohci controller found
on Allwinner sunxi SoCs.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Document the clock properties required by the spi-atmel driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Document the clock properties required by the atmel-mci driver.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
