Add the layout of the switch ports found on the BCM958625HR reference
board. The CPU port is hooked up to the AMAC0 Ethernet controlelr
adapter, so we also enable it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Switch Register Access Block node, this peripheral is identical
to the BCM5301x Northstar SoC, but we utilize the SoC-wide
"brcm,nsp-srab" compatible string to illustrate the integration
difference here.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add Device Tree entries for the Ethernet devices (AMAC) present on the Broadcom
Northstar Plus SoCs.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This will allow u-boot to fill in a mac-address for Orange Pi 2
variants which use an sdio wifi without an eeprom for the mac.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
There is a new Orange Pi PC *Plus* version available now,
this is an extended version of the regular Orange Pi PC
with sdio wifi and an eMMC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[Maxime: Fix model and compatible]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds description for the following features for this board:
- Serial port
- PCIe interfaces
- USB2.0
- USB3.0
- SDIO
- 1024 MiB NAND-FLASH
- SATA
- I2C buses
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit adds description for following features for this board:
- Serial port
- I2C buses
- 16MB SPI-NOR
- USB2.0
- USB3.0
- PCIe interfaces
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Marvell Armada 398 Development board contains both USB2.0 and USB3.0
ports, which can be handled by existing drivers.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Beside interfaces described in the armada-39x.dtsi and armada-395.dtsi, the
Armada 398 SoC family supports 2 additional SATA port (2 ports in one unit)
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Beside interfaces described in the armada-39x.dtsi, the Armada 395 SoC
family supports: 2 x SATA3 (2 ports in one unit) and the USB3.0
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Despite that FS states that rtc is present only in A395 and A398 and not in
A390, the rtc is working with A390.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The whole Armada 39x SoC family of processors has GPIO's which all can be
supported with existing driver.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The whole Armada 39x SoC family of processors has watchdog which can be
supported with existing driver.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The whole Armada 39x SoC family of processors has thermal sensor which can
be supported with existing driver.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This commit enables:
- CA9's Performance Monitor Unit
- CA9 MPcore SoC Controller
- Coherency fabric
on Armada 39x, basing on the Armada 38x (which has the same CA9 CPU).
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Lior Amsalem <alior@marvell.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Commit 1140011ee9 ("mmc: sdhci-pxav3: Modify clock settings
for the SDR50 and DDR50 modes") has extended the Device Tree
binding used to describe PXAv3 SDHCI controllers in order to be
able to use the SDR50 and DDR50 modes.
This commit updates the Device Tree description of the Armada
39x SDHCI controller in other to take advantage of this
functionality.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The armada-390.dtsi was broken since the first patch which adds Device Tree
files for Armada 39x SoC was introduced.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: <stable@vger.kernel.org> # 4.0+
Fixes 538da83 ("ARM: mvebu: add Device Tree files for Armada 39x SoC and board")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development board contains NAND FLSH which is
already enabled in existing dts. Nevertheless the default partition
description was missing.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The Armada 385 Access Point Development board contains USB port, which can
be handled by existing orion-ehci driver.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds the static MBus mappings for all supported SPI devices
(8 per controller) for the direct access SPI mode. They can be configured
and enabled by setting these MBus mapping in the 'ranges' property of the
per-board 'soc' node. If nothing is changed here, the default 'normal'
(indirect) SPI mode is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch moves all Armada 370/XP/38x/39x SPI controller nodes from the
'internal-regs' node down into the 'soc' node. This is in preparation
to enable the usage of the SPI direct access mode. A follow-up patch
will add the static MBus mappings for the SPI devices into the 'reg'
property of the SPI controller DT node.
By moving these SPI controller nodes, this patch also makes use of
the labels rather than keeping the tree structure.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Mark Brown <broonie@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch defines and uses common Armada XP pinctrl settings in
armada-xp.dtsi for the SPI1 interface (MPP13,14,16,17).
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
r8a7794 SDHI ch0 has SD_DMACR which is located in 0x324.
This patch updates register size
Based on work for the r8a7790 by Kuninori Morimoto.
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Define the Blanche board dependent part of the CAN0 device node along with
the CAN_CLK crystal.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 parts of the CAN0/1 device nodes.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The R-Car CAN controllers can derive the CAN bus clock not only from
their peripheral clock input (clkp1) but also from the other internal
clock (clkp2) and the external clock fed on the CAN_CLK pin. Describe
those clocks in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 part of the EtherAVB device node.
Based on the commit 89aac8af1a ("ARM: dts: r8a7794: add EtherAVB support").
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the EtherAVB clock and its parent, HP clock to the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe all 12 GPIO controllers in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the GPIO clocks in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) pin data for the SMSC LAN89218 Ethernet chip
to the Blanche board's device tree: the chip's IRQ output is connected to
the SoC's IRQ0 pin and its nCS input is connected to the SoC's EX_CS0# pin.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) SCIF0/3 pin data to the Blanche board's
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the generic R8A7792 part of the PFC device node.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add node to support SAMA5D2 Embedded Trace Macrocell and Embedded
Trace Buffer.
This patch depends on coresight-etm3x: Add ARM ETM-A5 peripheral ID
for proper coresight functionality.
It also depends on clocksource: timer-atmel-pit: enable mck to not
stall SAMA5D2 on bootup.
Signed-off-by: Olivier Schonken <olivier.schonken@gmail.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The rk3288 usbphy is completely enclosed in the general register files
and the updated binding allows it to be a subnode of the GRF now.
So move the node appropriately.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Firefly RK3288 Reload is a combination Firefly rk3288 core board
with the Reload baseboard. Add a dtsi for the Firefly rk3288 core
which can be included into the dts for the various baseboards
in the future and dts for Reload base board.
Currently supported are serial console, wired networking, eMMC and
SD storage, SPFIF, IR receiver, LEDs, SDIO wifi and USB. But only
the OTG could work on the host mode now, the other USB host can't
work now, additional patches are required.
Signed-off-by: Randy Li <ayaka@soulik.info>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds support for RK3288-Fennec boards. Currently supported
are serial console, wired networking, hdmi output and USB.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Panel regulator is controller by a regulator of the rk808 pmic.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Panel regulator is controller by a normal GPIO, so we need to
write a regulator-fixed node for it.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The default eDP panel on RK3288 EVB board is LG LP079QX1-SP0V TFT LCD,
we haven't declared the panel regulator in the 'panel-simple' device
node here, so the specific board like ACT8846 / RK8080 need to support
the panel power supply.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
bc677ff42e adds a device-tree property
to specify that an external watchdog reset is used to reset other
portions of the board and not just the IMX6 SoC.
This adds the property to the proper watchdog as well as the pinmux for
the Gateworks Ventana boards that use this external watchdog reset to
reset the PMIC which will reset all the PMIC power rails and not just
a chip-level IMX6 reset. This helps to work around various system issues
that can cause a hang when coming out of reset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This commit adds definition for cpu_on, cpu_off and cpu_suspend
commands. These definitions must match the corresponding PSCI
definitions in boot monitor.
Having those command and corresponding PSCI support in boot monitor
allows run time CPU hot plugin.
Link: http://lkml.kernel.org/r/E1b8koV-0004Hf-2j@rmk-PC.armlinux.org.uk
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Pratyush Anand <panand@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Simon Horman <horms@verge.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device tree contents continue to be the largest branches we submit. This
time around, some of the contents worth pointing out is:
- New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large delta due
to indentation changes
- A new Tegra K1 board: Apalis
- A bunch of small updates to many Allwinner platforms; new hardware support,
some cleanup, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=C4NU
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Device tree contents continue to be the largest branches we submit.
This time around, some of the contents worth pointing out is:
New SoC platforms:
- Freescale i.MX 7Solo
- Broadcom BCM23550
- Cirrus Logic EP7209 and EP7211 (clps711x platforms)_
- Hisilicon HI3519
- Renesas R8A7792
Some of the other delta that is sticking out, line-count wise:
- Exynos moves of IP blocks under an SoC bus, which causes a large
delta due to indentation changes
- a new Tegra K1 board: Apalis
- a bunch of small updates to many Allwinner platforms; new hardware
support, some cleanup, etc"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (426 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: at91: Don't build unnecessary dtbs
ARM: dts: at91: sama5d3x: separate motherboard gmac and emac definitions
ARM: dts: at91: at91sam9g25ek: fix isi endpoint node
ARM: dts: at91: move isi definition to at91sam9g25ek
ARM: dts: at91: fix i2c-gpio node name
ARM: dts: at91: vinco: fix regulator name
ARM: dts: at91: ariag25 : fix onewire node
...
Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we merge
through arm-soc for historical reasons, is also sizable this time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=O8+y
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
Pull watchdog updates from Wim Van Sebroeck:
"Core:
- min and max timeout improvements, WDOG_HW_RUNNING improvements,
status funtionality
- Add a device managed API for watchdog_register_device()
New watchdog drivers:
- Aspeed SoCs
- Maxim PMIC MAX77620
- Amlogic Meson GXBB SoC
Enhancements:
- support for the r8a7796 watchdog device
- support for F81866 watchdog device
- support for 5th variation of Apollo Lake
- support for MCP78S chipset
- clean-up of softdog.c watchdog device driver
- pic32-wdt and pic32-dmt fixes
- Documentation/watchdog: watchdog-test improvements
- several other fixes and improvements"
* git://www.linux-watchdog.org/linux-watchdog: (50 commits)
watchdog: gpio_wdt: Fix missing platform_set_drvdata() in gpio_wdt_probe()
watchdog: core: Clear WDOG_HW_RUNNING before calling the stop function
watchdog: core: Fix error handling of watchdog_dev_init()
watchdog: pic32-wdt: Fix return value check in pic32_wdt_drv_probe()
watchdog: pic32-dmt: Remove .owner field for driver
watchdog: pic32-wdt: Remove .owner field for driver
watchdog: renesas-wdt: Add support for the r8a7796 wdt
Documentation/watchdog: check return value for magic close
watchdog: sbsa: Drop status function
watchdog: Implement status function in watchdog core
watchdog: tangox: Set max_hw_heartbeat_ms instead of max_timeout
watchdog: change watchdog_need_worker logic
watchdog: add support for MCP78S chipset in nv_tco
watchdog: bcm2835_wdt: remove redundant ->set_timeout callback
watchdog: bcm2835_wdt: constify _ops and _info structures
dt-bindings: watchdog: Add Meson GXBB Watchdog bindings
watchdog: Add Meson GXBB Watchdog Driver
watchdog: qcom: configure BARK time in addition to BITE time
watchdog: qcom: add option for standalone watchdog not in timer block
watchdog: qcom: update device tree bindings
...
- Removal of most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to call
it if they have special needs.
- Use pr_fmt on all the DT core print statements.
- CoreSight binding doc improvements to block name descriptions.
- Add dt_to_config script which can parse dts files and list
corresponding kernel config options.
- Fix memory leak hit with a PowerMac DT.
- Correct a bunch of STMicro compatible strings to use the correct
vendor prefix.
- Fix DA9052 PMIC binding doc to match what is actually used in dts
files.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wLMr
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
* Removed CLK_IS_ROOT flag
New clk provider drivers:
* Renesas r8a7796 Clock Pulse Generator / Module Standby and Software
Reset
* Allwinner sun8i H3 Clock Controller Unit
* AmLogic meson8b clock controller (rewritten)
* AmLogic gxbb clock controller
* Support for some new ICs was added by simple changes to static data
tables for chips sharing the same family
Driver updates of note:
* the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with the
DT ABI
-----BEGIN PGP SIGNATURE-----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=1dpY
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Michael Turquette:
"The bulk of the changes are updates and fixes to existing clk provider
drivers, along with a pretty standard number of new drivers. The core
recieved a small number of updates as well.
Core changes of note:
- removed CLK_IS_ROOT flag
New clk provider drivers:
- Renesas r8a7796 clock pulse generator / module standby and
software reset
- Allwinner sun8i H3 clock controller unit
- AmLogic meson8b clock controller (rewritten)
- AmLogic gxbb clock controller
- support for some new ICs was added by simple changes to static
data tables for chips sharing the same family
Driver updates of note:
- the Allwinner sunxi clock driver infrastucture was rewritten to
comform to the state of the art at drivers/clk/sunxi-ng. The old
implementation is still supported for backwards compatibility with
the DT ABI"
* tag 'clk-for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (162 commits)
clk: Makefile: re-sort and clean up
Revert "clk: gxbb: expose CLKID_MMC_PCLK"
clk: samsung: Allow modular build of the Audio Subsystem CLKCON driver
clk: samsung: make clk-s5pv210-audss explicitly non-modular
clk: exynos5433: remove CLK_IGNORE_UNUSED flag from SPI clocks
clk: oxnas: Add hardware dependencies
clk: imx7d: do not set parent of ethernet time/ref clocks
ARM: dt: sun8i: switch the H3 to the new CCU driver
clk: sunxi-ng: h3: Fix Kconfig symbol typo
clk: sunxi-ng: h3: Fix audio clock divider offset
clk: sunxi-ng: Add H3 clocks
clk: sunxi-ng: Add N-K-M-P factor clock
clk: sunxi-ng: Add N-K-M Factor clock
clk: sunxi-ng: Add N-M-factor clock support
clk: sunxi-ng: Add N-K-factor clock support
clk: sunxi-ng: Add M-P factor clock support
clk: sunxi-ng: Add divider
clk: sunxi-ng: Add phase clock support
clk: sunxi-ng: Add mux clock support
clk: sunxi-ng: Add gate clock support
...
Pull ARM updates from Russell King:
"Included in this update are:
- Patches from Gregory Clement to fix the coherent DMA cases in our
dma-mapping code.
- A number of CPU errata updates and fixes.
- ARM cpuidle improvements from Jisheng Zhang.
- Fix from Kees for the location of _etext.
- Cleanups from Masahiro Yamada to avoid duplicated messages during
the kernel build, and remove CONFIG_ARCH_HAS_BARRIERS.
- Remove a udelay loop limitation, allowing for faster CPUs to
calibrate the delay correctly.
- Cleanup some left-overs from the SW PAN implementation.
- Ensure that a modified address limit is not visible to exception
handlers"
* 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (21 commits)
ARM: 8586/1: cpuidle: make arm_cpuidle_suspend() a bit more efficient
ARM: 8585/1: cpuidle: fix !cpuidle_ops[cpu].init case during init
ARM: 8561/4: dma-mapping: Fix the coherent case when iommu is used
ARM: 8561/3: dma-mapping: Don't use outer_flush_range when the L2C is coherent
ARM: 8560/1: errata: Workaround errata A12 825619 / A17 852421
ARM: 8559/1: errata: Workaround erratum A12 821420
ARM: 8558/1: errata: Workaround errata A12 818325/852422 A17 852423
ARM: save and reset the address limit when entering an exception
ARM: 8577/1: Fix Cortex-A15 798181 errata initialization
ARM: 8584/1: floppy: avoid gcc-6 warning
ARM: 8583/1: mm: fix location of _etext
ARM: 8582/1: remove unused CONFIG_ARCH_HAS_BARRIERS
ARM: 8306/1: loop_udelay: remove bogomips value limitation
ARM: 8581/1: add missing <asm/prom.h> to arch/arm/kernel/devtree.c
ARM: 8576/1: avoid duplicating "Kernel: arch/arm/boot/*Image is ready"
ARM: 8556/1: on a generic DT system: do not touch l2x0
ARM: uaccess: remove put_user() code duplication
ARM: 8580/1: Remove orphaned __addr_ok() definition
ARM: get rid of horrible *(unsigned int *)(regs + 1)
ARM: introduce svc_pt_regs structure
...
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.17 (GNU/Linux)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=8lmX
-----END PGP SIGNATURE-----
Merge tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
"New LED class driver:
- LED driver for TI LP3952 6-Channel Color LED
LED core improvements:
- Only descend into leds directory when CONFIG_NEW_LEDS is set
- Add no-op gpio_led_register_device when LED subsystem is disabled
- MAINTAINERS: Add file patterns for led device tree bindings
LED Trigger core improvements:
- return error if invalid trigger name is provided via sysfs
LED class drivers improvements
- is31fl32xx: define complete i2c_device_id table
- is31fl32xx: fix typo in id and match table names
- leds-gpio: Set of_node for created LED devices
- pca9532: Add device tree support
Conversion of IDE trigger to common disk trigger:
- leds: convert IDE trigger to common disk trigger
- leds: documentation: 'ide-disk' to 'disk-activity'
- unicore32: use the new LED disk activity trigger
- parisc: use the new LED disk activity trigger
- mips: use the new LED disk activity trigger
- arm: use the new LED disk activity trigger
- powerpc: use the new LED disk activity trigger"
* tag 'leds_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: is31fl32xx: define complete i2c_device_id table
leds: is31fl32xx: fix typo in id and match table names
leds: LED driver for TI LP3952 6-Channel Color LED
leds: leds-gpio: Set of_node for created LED devices
leds: triggers: return error if invalid trigger name is provided via sysfs
leds: Only descend into leds directory when CONFIG_NEW_LEDS is set
leds: Add no-op gpio_led_register_device when LED subsystem is disabled
unicore32: use the new LED disk activity trigger
parisc: use the new LED disk activity trigger
mips: use the new LED disk activity trigger
arm: use the new LED disk activity trigger
powerpc: use the new LED disk activity trigger
leds: documentation: 'ide-disk' to 'disk-activity'
leds: convert IDE trigger to common disk trigger
leds: pca9532: Add device tree support
MAINTAINERS: Add file patterns for led device tree bindings
* Minor cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mdxx
-----END PGP SIGNATURE-----
Merge tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC updates from Borislav Petkov:
"This last cycle, Thor was busy adding Arria10 eth FIFO support to the
altera_edac driver along with other improvements. We have two
cleanups/fixes too.
Summary:
- Altera Arria10 ethernet FIFO buffer support (Thor Thayer)
- Minor cleanups"
* tag 'edac_for_4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
ARM: dts: Add Arria10 Ethernet EDAC devicetree entry
EDAC, altera: Add Arria10 Ethernet EDAC support
EDAC, altera: Add Arria10 ECC memory init functions
Documentation: dt: socfpga: Add Arria10 Ethernet binding
EDAC, altera: Drop some ifdeffery
EDAC, altera: Add panic flag check to A10 IRQ
EDAC, altera: Check parent status for Arria10 EDAC block
EDAC, altera: Make all private data structures static
EDAC: Correct channel count limit
EDAC, amd64_edac: Init opstate at the proper time during init
EDAC, altera: Handle Arria10 SDRAM child node
EDAC, altera: Add ECC Manager IRQ controller support
Documentation: dt: socfpga: Add interrupt-controller to ecc-manager
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
A quiet regulator API release, a few new drivers and some fixes but
nothing too notable. There will also be some updates for the PWM
regulator coming through the PWM tree which provide much smoother
operation when taking over an already running PWM regulator after boot
using some new PWM APIs.
- Support for configuration of the initial suspend state from DT.
- New drivers for Mediatek MT6323, Ricoh RN5T567 and X-Powers AXP809.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXlk49AAoJECTWi3JdVIfQM4QH/jg2BGgdQSiuQspidmyN9tpL
hZgvUzrKm0eXEvzvTaL4cPymqpDHgQgaWEFo3Kv2WiU+34XIzfKPTt8m0WI37HY9
t4rTMlN8vL4WEMtAlB0i4DH1/jcEOJG2c88+tnSBGb5R8AXXIvx+F9xjWxOoJKJY
ccf5QcupDfCJw99rs3Li5eIbHOW2RAcZgurGGUyV01kH+G/9LliNpIKa9uCxK4dw
72aMH6QX+Hjid4UAqwL13C5W3sBDSebYYTwtTW61HosydLv818BfZC8IoezgjBRE
unjh6kdxOpcZk0ftciNiNQFLTUhobdYAuQFjUZywNqijpqK28lbFypweP8yhoxg=
=rDhl
-----END PGP SIGNATURE-----
Merge tag 'regulator-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"A quiet regulator API release, a few new drivers and some fixes but
nothing too notable. There will also be some updates for the PWM
regulator coming through the PWM tree which provide much smoother
operation when taking over an already running PWM regulator after boot
using some new PWM APIs.
Summary:
- Support for configuration of the initial suspend state from DT.
- New drivers for Mediatek MT6323, Ricoh RN5T567 and X-Powers AXP809"
* tag 'regulator-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (38 commits)
regulator: da9053/52: Fix incorrectly stated minimum and maximum voltage limits
regulator: mt6323: Constify struct regulator_ops
regulator: mt6323: Fix module description
regulator: mt6323: Add support for MT6323 regulator
regulator: Add document for MT6323 regulator
regulator: da9210: addition of device tree support
regulator: act8865: Fix missing of_node_put() in act8865_pdata_from_dt()
regulator: qcom_smd: Avoid overlapping linear voltage ranges
regulator: s2mps11: Fix the voltage linear range for s2mps15
regulator: pwm: Fix regulator ramp delay for continuous mode
regulator: da9211: add descriptions for da9212/da9214
mfd: rn5t618: Register restart handler
mfd: rn5t618: Register power off callback optionally
regulator: rn5t618: Add RN5T567 PMIC support
mfd: rn5t618: Add Ricoh RN5T567 PMIC support
ARM: dts: meson: minix-neo-x8: define PMIC as power controller
regulator: tps65218: force set power-up/down strobe to 3 for dcdc3
regulator: tps65218: Enable suspend configuration
regulator: tps65217: Enable suspend configuration
regulator: qcom_spmi: Add support for get_mode/set_mode on switches
...
Pull libata updates from Tejun Heo:
"libata saw quite a bit of activities in this cycle:
- SMR drive support still being worked on
- bug fixes and improvements to misc SCSI command emulation
- some low level driver updates"
* 'for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (39 commits)
libata-scsi: better style in ata_msense_*()
AHCI: Clear GHC.IS to prevent unexpectly asserting INTx
ata: sata_dwc_460ex: remove redundant dev_err call
ata: define ATA_PROT_* in terms of ATA_PROT_FLAG_*
libata: remove ATA_PROT_FLAG_DATA
libata: remove ata_is_nodata
ata: make lba_{28,48}_ok() use ATA_MAX_SECTORS{,_LBA48}
libata-scsi: minor cleanup for ata_scsi_zbc_out_xlat
libata-scsi: Fix ZBC management out command translation
libata-scsi: Fix translation of REPORT ZONES command
ata: Handle ATA NCQ NO-DATA commands correctly
libata-eh: decode all taskfile protocols
ata: fixup ATA_PROT_NODATA
libsas: use ata_is_ncq() and ata_has_dma() accessors
libata: use ata_is_ncq() accessors
libata: return boolean values from ata_is_*
libata-scsi: avoid repeated calculation of number of TRIM ranges
libata-scsi: reject WRITE SAME (16) with n_block that exceeds limit
libata-scsi: rename ata_msense_ctl_mode() to ata_msense_control()
libata-scsi: fix D_SENSE bit relection in control mode page
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.8:
API:
- first part of skcipher low-level conversions
- add KPP (Key-agreement Protocol Primitives) interface.
Algorithms:
- fix IPsec/cryptd reordering issues that affects aesni
- RSA no longer does explicit leading zero removal
- add SHA3
- add DH
- add ECDH
- improve DRBG performance by not doing CTR by hand
Drivers:
- add x86 AVX2 multibuffer SHA256/512
- add POWER8 optimised crc32c
- add xts support to vmx
- add DH support to qat
- add RSA support to caam
- add Layerscape support to caam
- add SEC1 AEAD support to talitos
- improve performance by chaining requests in marvell/cesa
- add support for Araneus Alea I USB RNG
- add support for Broadcom BCM5301 RNG
- add support for Amlogic Meson RNG
- add support Broadcom NSP SoC RNG"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (180 commits)
crypto: vmx - Fix aes_p8_xts_decrypt build failure
crypto: vmx - Ignore generated files
crypto: vmx - Adding support for XTS
crypto: vmx - Adding asm subroutines for XTS
crypto: skcipher - add comment for skcipher_alg->base
crypto: testmgr - Print akcipher algorithm name
crypto: marvell - Fix wrong flag used for GFP in mv_cesa_dma_add_iv_op
crypto: nx - off by one bug in nx_of_update_msc()
crypto: rsa-pkcs1pad - fix rsa-pkcs1pad request struct
crypto: scatterwalk - Inline start/map/done
crypto: scatterwalk - Remove unnecessary BUG in scatterwalk_start
crypto: scatterwalk - Remove unnecessary advance in scatterwalk_pagedone
crypto: scatterwalk - Fix test in scatterwalk_done
crypto: api - Optimise away crypto_yield when hard preemption is on
crypto: scatterwalk - add no-copy support to copychunks
crypto: scatterwalk - Remove scatterwalk_bytes_sglen
crypto: omap - Stop using crypto scatterwalk_bytes_sglen
crypto: skcipher - Remove top-level givcipher interface
crypto: user - Remove crypto_lookup_skcipher call
crypto: cts - Convert to skcipher
...
Here's the big USB driver update for 4.8-rc1. Lots of the normal stuff
in here, musb, gadget, xhci, and other updates and fixes. All of the
details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPioPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB5AAnj7a
VJ2t2kcWzFUNQ6dyJrJCGGRAAKDZmb5CnOGeqJmdVpDzN1CGLYjfiw==
=47iA
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
Replace the non-standard vendor prefix stm with st for
STMicroelectronics. The drivers do not specify the vendor prefixes
since the I2C Core strips them away from the DT provided compatible
string. Therefore, changing existing device trees does not have any
impact on device detection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Rob Herring <robh@kernel.org>
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXjKQhAAoJEBx+YmzsjxAgGwQQAIbAJ4R3d9eNQO1wGknnmMyV
M2u6lnLUm1R6b/9EMAqYN5Hm/Dvg13CBXtMz/GaaQJZQHPrWlsRu0XqSYrSiSVMn
8YcdPmVpflIMrtxP+OjKN1maVnn8kJCnVlku4nEbjN9ScB6tpgs6QcV6uponnD+3
vt3nU610WxAfXjvvtd4yflYM6/YTxZEn3zACiiv43VP9wZ6noUNEhDeJqS7I52kZ
AqsRJd0unojfvltejC6G62EmiesA93nX0TI0nKCP0Ink8y0pHTe4/w1nhRPCr1dS
hJQEihcD/ZNs+k1P5s8UJE86PI4l+Y/AY7r48iEf5vxEnbF0nKdukpVy6/jfheMy
+tvC0pJjCj5Ed9AxyaCghGhU0/MeEUCNFemgOvbsHQCd1KWramJq8/6joRrzmzDQ
tvmlNOgJYj53gkkLuKIzQB9zbuqCzLhNDUwx8NUyIgBbUBF33Wxw7XVTmqQuGEl0
+AC1kPuIFen4aiyN8VYytJhTcjD5MvPOG9PsWs8JDGCjLe4lUJ9ztF5ovxDmTGHh
plazJb/aMuERrX2Dxi4mHnr01D5D3qVEpGPjw55DiWuXaWXCtKjX6/F8HxZiaDDS
kJeMPjEkQ7zgVZchDRTsniqHbOOMsbP6DErYwHwXPLNjWyLdhpLgKU4edOW7MEA+
3tRQScPdk0oqDUq7XIhW
=QU36
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8, take 2" from Maxime Ripard:
Another set of changes for the 4.8 merge window, among which:
- Reworking of the DT for the tablets based on Allwinner reference design
and q8 designs to avoid duplication as much as possible
- Renaming a DT merged in the first PR for consistency
- Enable a few devices on some boards
- New boards: Polaroid MID2407PXE03, inet86dz
* tag 'sunxi-dt-for-4.8-2-bis' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (21 commits)
ARM: dts: sun8i: Add dts file for inet86dz board
ARM: dts: sun8i: Add dts file for Polaroid MID2407PXE03 tablet
ARM: dts: sun8i: Use sun8i-reference-design-tablet for ga10h dts
ARM: dts: sun8i: Use sun8i-reference-design-tablet for polaroid mid2809pxe04
ARM: dts: sun8i: reference-design-tablet: Add drivevbus-supply
ARM: dts: Copy sun8i-q8-common.dtsi sun8i-reference-design-tablet.dtsi
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for utoo p66 dts
ARM: dts: sun5i: Use sun5i-reference-design-tablet.dtsi for dit4350 dts
ARM: dts: sun5i: reference-design-tablet: Remove mention of q8
ARM: dts: sun5i: reference-design-tablet: Set lradc vref to avcc
ARM: dts: sun5i: Rename sun5i-q8-common.dtsi sun5i-reference-design-tablet.dtsi
ARM: dts: sun5i: Move q8 display bits to sun5i-a13-q8-tablet.dts
ARM: dts: sunxi: Rename sunxi-q8-common.dtsi sunxi-reference-design-tablet.dtsi
ARM: dts: sun7i: bananapi-m1-plus: red LED is power LED
ARM: dts: sun7i: bananapi-m1-plus: Unify suffix for board specific labels
ARM: dts: sun7i: bananapi-m1-plus: Reindent whole file using tabs
ARM: dts: sun7i: lamobo-r1: Enable audio codec
ARM: dts: sun7i: lamobo-r1: Fix GPIO flags in reg_ahci_5v
ARM: dts: sun8i-h3: Rename sinovoip-bpi-m2-plus to bananapi-m2-plus
ARM: dts: sun7i: lamobo-r1: Remove usb1 vbus regulator
...
The inet86dz board is a board used in 7" tablets from various oems.
These tablets are a23 based 7" tablets featuring a 1024x600 LCD,
512MB RAM, 4G NAND, rtl8188etv usb wifi, gsl1680 touchschreen,
micro-sd slot, 3.5mm headphone jack and a micro-usb otg connector
which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Polaroid MID2407PXE03 is an a23 based 7" tablet based on a M86_MB V2.0
PCB, featuring a 800x480 LCD, 512MB RAM, 4G NAND, esp8089 wifi, gsl1680
touchschreen, micro-sd slot, 3.5mm headphone jack and a micro-usb otg
connector which doubles as charging port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables backlight, regulator and full otg
support. I've tested that all these works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a drivevbus-supply property so that the drivevbus regulator
reports the right voltage value.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Copy sun8i-q8-common.dtsi to sun8i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Note that in this case we keep sun5i-q8-common.dtsi as it is shared
between a23 / a33 q8 tablets. Also we leave the usb-wifi config in
there (rather then in sun8i-reference-design-tablet.dtsi) as most
sun8i tablets use sdio wifi rather then usb wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in a nice cleanup for this dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
Note as a side-effect this also enables the on board speaker / headphones
out. I've tested that this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Remove all mention of q8 from sun5i-reference-design-tablet.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Set lradc vref to the actual avcc ldo, rather then to the fixed 3v0
regulator from common-regulators.dtsi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename sun5i-q8-common.dtsi to sun5i-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is a preparation patch for renaming sun5i-q8-common.dtsi to
sun5i-reference-design-tablet.dtsi and sharing it between all
the A13 tablet dts files.
Since we only have a panel config for the 18 tablets (for now) move
this to the q8 specific dts file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename sunxi-q8-common.dtsi to sunxi-reference-design-tablet.dtsi. This
is part of renaming all the sun?i-q8-common.dtsi files to
sun?i-reference-design-tablet.dtsi since most of the hw-config in there
is shared by all sunxi tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Commit 0dfd582e02 ("watchdog: qcom: use timer devicetree
binding") moved to use the watchdog as a subset timer
register block. Some devices have the watchdog completely
standalone with slightly different register offsets as
well so let's account for the differences here.
The existing "kpss-standalone" compatible string doesn't
make it entirely clear exactly what the device is so
rename to "kpss-wdt" to reflect watchdog timer
functionality. Also update ipq4019 DTS with an SoC
specific compatible.
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Update the compatible string to align with driver and also
add SoC specific string to DTS.
CC: linux-watchdog@vger.kernel.org
Signed-off-by: Matthew McClintock <mmcclint@codeaurora.org>
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Building both ARMv4 and ARMv5 dtbs when SOC_SAM_V4_V5 is an issue for
kernelci because it will then attempt to boot ARMv4 kernels on at91sam9
which doesn't work.
Use CONFIG_SOC_AT91RM9200 and CONFIG_SOC_AT91SAM9 instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Separate the definitions for the emac and the gmac in different files and
include them in the final board dts that uses them.
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f0028000 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/ethernet@f802c000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add a reg property in the endpoint node as documented in
Documentation/devicetree/bindings/media/video-interfaces.txt
Solves:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000/port/endpoint@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The ISI is only present on the at91sam9g25, move the definition to the
at91sam9g25ek board dts to avoid warnings.
Solves the following warning for other 9x5ek boards:
Warning (unit_address_vs_reg): Node /ahb/apb/isi@f8048000 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
i2c-gpio doesn't need a reg property. Change the node names to i2c-gpio-x
as used in other dts to remove the unit-address.
Solves:
Warning (unit_address_vs_reg): Node /i2c@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /i2c@2 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_3v3_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Remove the unit-address from the oneiwire node as it doesn't have a reg
property.
Solves:
Warning (unit_address_vs_reg): Node /onewire@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_mmc1_reg is a fixed regulators and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@2 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a
reg property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_3v3_reg and vcc_mmc1_reg are fixed regulators and don't need a reg
property. Remove their unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /fixedregulator@1 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
vcc_mmc0_reg is a fixed regulator and doesn't need a reg property. Remove
its unit-address.
Solves:
Warning (unit_address_vs_reg): Node /fixedregulator@0 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
lcd_bus has never been mainlined and is replaced by the atmel_hlcdc driver.
Remove stale nodes.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Endpoint nodes have a reg property. Add their mandatory unit-address.
This solves:
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep0 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep1 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep2 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep3 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep4 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep5 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep6 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep7 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep8 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep9 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep10 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep11 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep12 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep13 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep14 has a reg or ranges property, but no unit name
Warning (unit_address_vs_reg): Node /ahb/gadget@00400000/ep15 has a reg or ranges property, but no unit name
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
The triggers don't need a reg property, remove it when prenset. Also remove
the unit-address from their name.
This solves:
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /ahb/apb/adc@fc034000/trigger@3 has a unit name, but no reg property
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Simon Horman told me that R8A7792 has ADSP clock based on an incorrect
table in the most recent R-Car gen2 manual. But when I received that manual
I discovered that this is false: R8A7792 is the only Gen 2 SoC that doesn't
have ADSP at all. Accordingly remove the ADSP clock from DT for the
r8a7792.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Despite the fact that QSPI clock has PLL1/VCOx1/4 clock as a parent, the
latter hasn't been added to the R8A7792 device tree. This patch corrects
that oversight.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Merge "STi late updates for v4.8" from Patrice Chotard:
- Add STi DT critical clocks declaration
- Remove SPI hack wich has dependecy with critical clocks
These 2 STi DT patches and SPI hack MUST be applied after patches
contained into Stephen Boyd's branch clk-next/clk-st-critical.
This to ensure not to break SPI.
* tag 'sti-late-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pchotard/sti:
spi: st-ssc4: Remove 'no clocking' hack
ARM: sti: stih410-clocks: Identify critical clocks
ARM: sti: stih407-family: Supply defines for CLOCKGEN A0
clk: st: clkgen-pll: Detect critical clocks
clk: st: clkgen-fsyn: Detect critical clocks
clk: st: clk-flexgen: Detect critical clocks
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXg7ZKAAoJEN0jrNd/PrOhSeIP/A3kTBHvCIk9BTZCOAOAb1u0
NdzJdH/qUFVzPESSbzYeAQpRLFZzFKG+6gCdY3IMsoAXvPwE+pMkJSm7i8zkpTtV
CvEJOG523MhHde065X+z0LpenRKA92s7E08yoqJaaqkUxeYAGXQi+yURixCZ0kmF
9bARzmC3b4qo4+nndEvlKdbgycW942LvFHWMdScqkFgV68POpDA3BqFSztI8j741
1zM9ggcMgxJqYteZYrrdiPUzaoS4j0EEseuzaVETCzon0KICkIW6CMNg0Q0aNfNk
sidE320KjCihioeYem85vluIBFDLBZCO4SrR0XSj4JKth0/LkEdBakA/tp6kP8u/
M2g9ZT9k620EcuSf5LEOCHRdSYFF5+b9+qKdKK7ZMO7H55o1G2dHCYNutT8KZDRw
p7u65EQNZy8yLnCa2lxL6c6pLDcOxp8bON0ZD6+K1B2xfebvko96Ec/eEljqbgLo
SnWDSkyNFKWljWG11Ie4u43beA7QzwwCvHqyspuPmNHZjMeIp25FqJy4tZ31prDg
+TuA+13SFaAT4uamD1PYRZSZEaTiLwoD21zxKS4Jy7O6uX4P/pbmpK/ispvJe5FZ
HWvlbmtWIFgkaY1PlGuBINhuB5es96d4OoXGuGouAk6Xf8PhELk6JSZ2eLEMtfdv
/Y04dzuWCUKuzOYzGnRz
=h8a0
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt
Merge "ARM: tegra: Device tree changes for v4.8-rc1" from Thierry Reding:
Some cleanups to existing device tree sources and add Toradex Apalis TK1
support.
* tag 'tegra-for-4.8-arm-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
ARM: tegra: Initial support for Apalis TK1
ARM: tegra: Remove commas from unit addresses on Tegra124
ARM: tegra: Import latest Jetson TK1 spreadsheet
ARM: tegra: Add spaces around = in properties
ARM: tegra: Fix a couple of DTC warnings
Lots of platforms contain clocks which if turned off would prove fatal.
The only way to recover is to restart the board(s). This driver takes
references to clocks which are required to be always-on. The Common
Clk Framework will then take references to them. This way they will
not be turned off during the clk_disabled_unused() procedure.
In this patch we are identifying clocks, which if gated would render
the STiH410 development board unserviceable.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The clearfog DTS should not be defining the on-board phy, this device
is located on the microsom. Remove the duplicated definition.
Reported-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
This patch adds the device tree to support Toradex Apalis TK1 a
computer on module which can be used on different carrier boards.
The module consists of a Tegra TK1 SoC, a PMIC solution, 2 GB of DDR3L
RAM, a bunch of level shifters, an eMMC, a TMP451 temperature sensor
chip, an I210 gigabit Ethernet controller and a SGTL5000 audio codec.
Furthermore, there is a Kinetis MK20DN512 companion micro controller for
analogue, CAN and resistive touch functionality which is not yet
supported. Anything that is not self contained on the module is disabled
by default.
The device tree for the Evaluation Board includes the module's device
tree and enables the supported peripherals of the carrier board (the
Evaluation Board supports almost all of them).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Remove commas from unit addresses as suggested by Rob Herring upon me
posting initial Apalis TK1 support:
http://article.gmane.org/gmane.linux.ports.tegra/26608
Please keep the remaining 0, notation on the GPU node in place as a
former mainline U-Boot version was looking for that particular notation
in order to perform required fix-ups on it.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This imports v11 of "Jetson TK1 Development Platform Pin Mux" from
https://developer.nvidia.com/embedded/downloads.
The new version defines the mux option for the MIPI pad ctrl selection.
The OWR pin no longer has an entry in the configuration table because
the only mux option it support is OWR, that feature isn't supported, and
hence can't conflict with any other pin. This pin can only usefully be
used as a GPIO.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This seems to have been copied and pasted since the beginning of time,
though only until Tegra124, likely because that DT was written from
scratch or it was fixed along the way.
Signed-off-by: Thierry Reding <treding@nvidia.com>
The red led on the Bananapi M1+ is wired to light up as soon as the
board is powered, and continues to be lit while the GPIO is floating.
Rename the LED to "pwr", remove the default trigger, and mark it as
default on.
Also fix the pinmux node that was specifying a different pin for this
LED.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The dts file uses "bananapi" for some labels and "bananapim1plus" for
other. Use the shortened "bpi_m1p" suffix for all board specific labels.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The bananapi-m1-plus dts file was indented using 4 spaces, without
tabs. This does not match the code style.
Reindent the whole file before we do anything else.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Lamobo R1 has a headphone jack for audio output, and an onboard
microphone. These are tied to the SoC's internal audio codec.
Enable the audio codec.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
reg_ahci_5v uses a GPIO in active high mode. Use the proper macro,
instead of just 0 for the GPIO flags.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Banana Pi series is a well known series of single board computers.
The manufacturer, Sinovoip, is less well known. Moreover, the board
markings do not mention Sinovoip, but only the Banana Pi logo, and
the BPI-M* model name.
Rename the dts file to use the more well known name. Also fix up
some of the model names and labels to match other Banana Pi boards.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
USB1 VBUS is directly tied to the 5V rail on the board. It is not
individually controllable. Drop the regulator.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the Lamobo R1, USB2 is connected to the RTL8192CU WiFi module.
The power enable pin is connected to PH12.
Fix the enable pin the reg_usb2_vbus.
Also disable ohci1, as the WiFi module is USB 2.0 capable.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- pin control nodes for pxa2xx and pxa3xx
- the LCD controller for pxa2xx
- the missing pxa3xx pulse width modulator nodes
- an USB Host fix for pxa3xx
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9doC
-----END PGP SIGNATURE-----
Merge tag 'pxa-dt-4.7' of https://github.com/rjarzmik/linux into next/dt
This device-tree pxa update brings :
- pin control nodes for pxa2xx and pxa3xx
- the LCD controller for pxa2xx
- the missing pxa3xx pulse width modulator nodes
- an USB Host fix for pxa3xx
* tag 'pxa-dt-4.7' of https://github.com/rjarzmik/linux:
ARM: dts: pxa3xx: add pincontrol helpers
ARM: dts: pxa: add pinctrl to pxa3xx
ARM: dts: pxa: fix the ohci clock for pxa3xx
ARM: dts: add pincontroller to pxa27x
ARM: dts: pxa: add pxa3xx pwm nodes
ARM: dts: pxa: add pxa framebuffer device
Signed-off-by: Olof Johansson <olof@lixom.net>
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Ie0I
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux into next/dt
Merge "additional Broadcom ARM-based SoC Device Tree changes" from Florian Fainelli:
- Lubomir updates all BCM2835 (Raspberry Pi family) Device Tree source files with
their proper information about the on-board USB Ethernet adapter so there is
appropriate binding between this USB device and a device_node (useful for MAC
address fetching and stuff)
- Raveendra adds the ADC controller Device Tree nodes to the Cygnus SoC device
tree include files
- Rafal updates the BCM5301x Device Tree by separating how we specify the NAND
chip-select information in a first change and then fixes the NAND controller
ECC configuration for the D-Link DIR-885L
- Florian adds support for the BCM953012ER reference board, adds the HW random
number generator DT node and adds proper memory node information to the
BCM958625HR reference board
* tag 'arm-soc/for-4.8/devicetree-part2' of http://github.com/Broadcom/stblinux:
ARM: dts: NSP: Specify RAM amount for BCM958625HR board
ARM: BCM5301X: Fix NAND ECC parameters for D-Link DIR-885L
ARM: BCM5301X: Specify NAND chip select and ECC in separated files
ARM: dts: Cygnus: Add Broadcom iproc-static-adc DT node
ARM: dts: BCM5301x: Add BCM953012ER board
ARM: dts: BCM5301x: Add RNG Device Tree node
ARM: bcm2835: dt: Add the ethernet to the device trees
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7zT7
-----END PGP SIGNATURE-----
Merge tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi into next/dt
Merge "ARM: DT: Hisilicon ARMv7 SoC Hi3519 DT updates for 4.8" from Wei Xu:
- Add device tree bindings for hi3519 sysctrl
- Add dts files for hi3519
- Tidy up DTB makefile entries to keep the list sorted
* tag 'hisi-armv7-soc-dt-for-4.8-v2' of git://github.com/hisilicon/linux-hisi:
ARM: dts: add dts files for Hi3519 and tidy up the makefile entries
ARM: dt-bindings: add device tree bindings for Hi3519 sysctrl
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XPdf
-----END PGP SIGNATURE-----
Merge tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt
Merge "Allwinner DT changes for 4.8" from Maxime Ripard:
The usual amount of DT patches, among which:
- I2S support
- Support for the AXP809 in the relevant boards (A80 based)
- New boards: Banapi M1+, Banapi M2+, Allwinner Parrot (R16 EVB),
- The other patches to enable various controllers on our boards, most
notably USB OTG
* tag 'sunxi-dt-for-4.8' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (54 commits)
ARM: dts: sun5i: Enable otg on the auxtex t004
ARM: sun5i: Allow PLL3 2x fixed factor clock to change PLL3 rate
ARM: sun7i: Add DAI nodes
ARM: sun7i: Add mod1 clock nodes
ARM: dts: sun5i: Add mmc1 / sdio-wifi node to mk802
ARM: dts: sun5i: Add axp152 pmic node to mk802
ARM: dts: sun5i: Enable otg on the mk802
ARM: dts: sun7i: Add BCM53125 switch nodes to the lamobo-r1 board
ARM: sun8i: Add Parrot Board DTS
ARM: dts: sun5i: q8-common: Enable USB-based WiFi
ARM: dts: sun7i: Add dts file for Bananapi M1 Plus board
ARM: dts: sun8i-q8-common: Add support for USB wifi controllers
ARM: dts: sun9i: a80-optimus: Order nodes by alphabetical order
ARM: dts: sun9i: cubieboard4: Order nodes by alphabetical order
ARM: dts: sun7i: Add NFC node to Allwinner A20 SoC
ARM: dts: sun4i: Add NFC node to Allwinner A10 SoC
ARM: dts: sun6i: Add pmic / regulator nodes to Mele M9 dts
ARM: dts: sun6i: Add pmic / regulator nodes to Mele A1000G quad dts
ARM: dts: sun6i: The blue led on the Mele M9 is a power led
ARM: dts: sun6i: The blue led on the Mele A1000G quad is a power led
...
- Fix the I2C address and supply line names for the AK8974
- Sets up the interrupt lines to the different components as they
actually are connected, I was confused for some time by the fact
that several lines were connected with <NM> 0 Ohm resistors, which
means NOT MOUNTED and is thus not 0 Ohm at all but infinite ohms,
i.e. not connected at all.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABCAAGBQJXdbKVAAoJEPOmecmc0R2B4t8H/3J/l3fXyAskseN12883GkgO
WxEaCe4LeLbxp9Lcd3jmhXM4WZKPbfngYdLvL6kNh/LZeZT3naa2B55ot0FiIOHQ
PVvAC9ce7T0wTeK/aC2iFU6two6ZMbk8jSRfpfpijHIwK9U1NQcXTssuzvHR+S/L
+QP29M2TP3Y9UrPydx8kpCeH0kav2WmdqNmRdpQ9hokCqAiR2jbXi2N4PNtVl9v9
Vy/s+kFa8RSLzWTUICalwrMzS7j/VyeFKq61NPPjVdfS0Q+poCcdaDw5ZPEtZYBu
eerD1hTou+z7MPz6F5SM3J5U9G8NEp0NO4b3C0eWvAuA9cMv0smJFfqVD4erp40=
=wEmr
-----END PGP SIGNATURE-----
Merge tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Audio support and spi-flash on rk3288-veyron Chromedevices
as well as i2s and ethernet support on rk3228/rk3229 devices
and a dts file for the rk3229 eval board.
* tag 'v4.8-rockchip-dts32-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: add support rk3229 evb board
ARM: dts: rockchip: add GMAC nodes for RK322x SoCs
ARM: dts: rockchip: add i2s nodes for RK322x SoCs
ARM: dts: rockchip: rename rk3228.dtsi to rk322x.dtsi
clk: rockchip: add clock-ids for rk3228 MAC clocks
clk: rockchip: add clock-ids for rk3228 audio clocks
ARM: dts: rockchip: rename i2s model for Veyron devices
ARM: dts: rockchip: move rk3288 io-domain nodes to the grf
ARM: dts: rockchip: Enable analog audio on rk3288-veyron chromebooks
ARM: dts: rockchip: Add shared file for audio on rk3288-veyron boards
ARM: dts: rockchip: add SPI flash node for rk3288-veyron
Signed-off-by: Olof Johansson <olof@lixom.net>
This allows to switch the card signal voltage level to 1.8 V, which is
needed for any ultra high speed modes to work.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=gmxg
-----END PGP SIGNATURE-----
Merge tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt
Second Round of Renesas ARM Based SoC DT Updates for v4.8
* Use APMU on R-Car Gen2 and provide SMP for r8a7793 SoC
* Update console parameters to uniformly use chosen/stdout-path,
serial0, not provide kernel unnecessary command line parameters
* Add DU pins to silk board
* Add support for blanche/r8a7792
* Name pfc subnodes after device name
* tag 'renesas-dt2-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (41 commits)
ARM: dts: r8a7792: add SMP support
ARM: dts: r8a7793: Add APMU node and second CPU core
ARM: dts: r8a7791: Add APMU node
ARM: dts: r8a7790: Add APMU nodes
devicetree: bindings: Renesas APMU and SMP Enable method
ARM: dts: kzm9g: Update console parameters
ARM: dts: kzm9d: Update console parameters
ARM: dts: marzen: Add serial port config to chosen/stdout-path
ARM: dts: genmai: Update console parameters
ARM: dts: armadillo800eva: Update console parameters
ARM: dts: r8a7792: add JPU support
ARM: dts: r8a7792: add JPU clocks
ARM: dts: silk: add DU pins
ARM: dts: blanche: add Ethernet support
ARM: dts: blanche: initial device tree
ARM: dts: blanche: document Blanche board
ARM: dts: r8a7792: add IRQC support
ARM: dts: r8a7792: add [H]SCIF support
ARM: dts: r8a7792: add SYS-DMAC support
ARM: dts: r8a7792: initial SoC device tree
...
Signed-off-by: Olof Johansson <olof@lixom.net>
This device uses BCH-1 instead of BCH-8. This fixes ECC errors and makes
NAND usable with brcmnand.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Using separated file with common chip select parameters will allow us
adding other ECC setups without code duplication.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This adds the Cirrus Logic EP7209,EP7211 DT templates and support for
EDB7211 Development board.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
- add dts files for Hi3519
- shuffle ARCH_HIGHBANK, ARCH_HISI, ARCH_HIX5HD2 and ARCH_HIP0X
around to keep the list sorted
Signed-off-by: Jiancheng Xue <xuejiancheng@huawei.com>
Signed-off-by: Wei Xu <xuwei5@hisilicon.com>
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXdL1gAAoJEME3ZuaGi4PXDgEP/1iPrO92izin4BTql9CxJQ5L
LlSHwWeE6JTd/qaMcs8bbRrP1mROLkZozyqkj7QUgxoZxeyXrVpzhjerUp9QSLz4
Pq9Ql57cc4F03mns1uNaZ9Bz9c3vhtoohwkLRHvC4n7yQ4zvjCoyRDXGZ4+osz+K
vrlRpm3ZZrkr/MM4QuW9E7O2vL8/1kuPjn10vgCGEyWTSsMHHJe1+m4mpz5p/uPb
RB8I1ZIdrvXyBJeNAhgCxWJ27nw2xpotqjAO5h2z/XZ8VSOIktd2iiouu199knso
jPrVdJWuY0vv8YBXdJG/3/86T3S8w+HN1ULtaVIcYAbG44TLkzz1YCku3UUWB2yK
INZ2J4dreXZ8NvcQPQffcE3B25w+hNx6mDlrAmRaapstLlPIkeNWeiYMI4CaoxTa
1lOGqUuw6gc9JlBrEkJilBS18A9ExzNlquiBJa3EiP/74axe2AriSxbZZCpQ6na0
mOkuW/0xO9iSE56+j1pUuz/GCmoJt4rCMTCRVp17eE6WUM6OW+oUWm0ArVefBCy/
Er5E3WwXNA4nhEuWU6Y1oh/ji2SNzr9eNU3eja254xgOGsHIW1iqaCappUBi4+VC
cm6TaXSlzDBv3v/1kQT947LiHkc+5A4/mldizDSaujF9vjIyQvHzG+yGpHEbyWAT
qf37rI3BB2GJgs13U5Jf
=sS8p
-----END PGP SIGNATURE-----
Merge tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for Exynos MFC changes for v4.8, part 2:
Replace hardcoded reserved memory ranges with auto-allocated ones
and enable MFC for all boards.
* tag 'samsung-drivers-exynos-mfc-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: enable MFC device for all boards
ARM: dts: exynos: move MFC reserved memory regions from boards to .dtsi
ARM: dts: exynos: replace hardcoded reserved memory ranges with auto-allocated ones
ARM: dts: exynos: Enable MFC device on Exynos4412 Odroid boards
ARM: dts: exynos: Convert MFC device to generic reserved memory bindings
ARM: EXYNOS: Remove code for MFC custom reserved memory handling
media: s5p-mfc: add iommu support
media: s5p-mfc: replace custom reserved memory handling code with generic one
media: s5p-mfc: use generic reserved memory bindings
of: reserved_mem: add support for using more than one region for given device
media: set proper max seg size for devices on Exynos SoCs
media: vb2-dma-contig: add helper for setting dma max seg size
s5p-mfc: Fix race between s5p_mfc_probe() and s5p_mfc_open()
s5p-mfc: Add release callback for memory region devs
s5p-mfc: Set device name for reserved memory region devs
Signed-off-by: Olof Johansson <olof@lixom.net>
This is a series of dtc warning fixes when compiled with make W=2
from Javier Martinez Canillas <javier@osg.samsung.com>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXdMKhAAoJEBvUPslcq6Vz9d0P/Redrumw0+JuFTBIUyJNtILX
6u+TXabPgPvkxEZ/eFPLv6b8EcZBkOVXPfbTnvUKzsT+VXjD1QnufYm1fw+qzmBA
Fijii54z5EyhnOMEm8Zr962rExwL7rMr/lHi62Dfs/d8zG9AEMq8UU9hO1vn3vkr
JDsK2BdyoFTDq+PVYXpjKCaVpXPV0+FS8YDH5uoXzCF1vYD7fSCGRnM4HwaNEA65
RukMtafx0Kv9euS8fpjeZ+dHQI+tcrp72hokhmGkSAN1zAVWGLllvwxHudwvYHSi
ZHhSIr6m5REF2JC7PekYMA8nsf0WfdoYwLB52fckissrIzXllW3MgFxgXrqbH4iZ
sx3aXZvM6grZmn0Ou8jbUsaGd8ri1wRCb5SAJx9yYMuywWVKUO+D5ViLhLHUSmva
XeiXLw7cBZQyBJv00lR66H6G5ABcNjdnvuwpRUHIWWH+6/DGXnzM1ZejHQjR6phZ
1XEF3Mo7ZgTUXARTEBNgu7KGyMhx1YH1OVLF4Ri8eM77qZ84CQbP3AeqAQxsSJPi
7YDqhZZJ4bVHeEy7RQdf/OSz5Gf7jgRreqYpfenZc/3OlfYsnewbu9Fo3w87L81E
EzE5Jdwq/vyjEs5EBwEP7uvKzYh64qVfp+puCxUBpPZmPiD2zMkCndt3O849Sm6x
qHfIDkk9XN6fPXlQRiwW
=ikLv
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Second set of device tree updates for omaps for v4.8 merge window.
This is a series of dtc warning fixes when compiled with make W=2
from Javier Martinez Canillas <javier@osg.samsung.com>.
* tag 'omap-for-v4.8/dt-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: dts: am57xx: sbc-am57x: remove unneded unit name
ARM: dts: omap5-board-common: remove unneded unit names
ARM: dts: omap5-cm-t54: remove unneded unit names and add reg properties
ARM: dts: am437x: cm-t43: remove unneded unit names
ARM: dts: am437x-gp-evm: remove unneded unit name
ARM: dts: am43xx-epos-evm: remove unneded unit name
ARM: dts: omap4-var-om44customboard: remove unneded unit name
ARM: dts: omap4-sdp: remove unneded unit names
ARM: dts: omap4-panda-common: remove unneded unit names
ARM: dts: omap4-duovero-parlor: remove unneded unit name
ARM: dts: omap3-thunder: remove unneded unit name
ARM: dts: sbc-t3x30: remove unneded unit names
ARM: dts: omap3-pandora-common: remove unneded unit name
ARM: dts: omap3-overo-common-dvi: remove unneded unit names
ARM: dts: omap3-igep0020-common: remove unneded unit names
ARM: dts: omap3: overo: remove unneded unit names in display nodes
ARM: dts: omap3-ha-lcd: remove unneeded unit name
ARM: dts: omap3-gta04: remove unneeded unit names
ARM: dts: omap3-devkit8000-lcd-common: remove unneeded unit names
ARM: dts: omap3-devkit8000: remove unneeded unit names
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXcmoVAAoJEFBXWFqHsHzOQfEH/1z78cIe4bBd61boOge5VGUc
BdVGC4U6vcB1cRxceA8sh6U8QVyDtnojB1r5C3W+Zad4VMIdptGwbxAJne268WTt
iSRY8+Mu81KgrvkQ4flosTp7w8J4DfzithMGzDnhq3vTFblaaAT63u9AcDlcSGCq
1p/wPpqUb7COEBYOAxcOfypIPkZXrcvTfHHm3KOAV+cvNEQHZ0n4kLDWfjFxiUgo
oE+RDTku2q7mfXs22QXCUyTLNlwzuczsQ35sPM4JbIc6JBVYyyF/tHQFB162MB7u
ELK79F4LKip4wUS8b52M3xEQWiB0Cb1jtymomHLdGzguk7FtaV18vSUvA918GB8=
=2NUH
-----END PGP SIGNATURE-----
Merge tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/dt
The i.MX device tree update for 4.8:
- Add two i.MX23/STMP3780 based MP3 player device support, Creative
X-Fi3 and SanDisk Sansa Fuze+
- Add the support of Auvidea H100 device which is a SolidRun MicroSOM
baseboard
- Restructure i.MX7Dual DTS files to support i.MX7Solo and add Toradex
Colibri iMX7S/iMX7D boards
- Device additions and enabling for various boards: mmc device for
utilite-pro, IRQ controller and CAN support for TS-4800, display and
touchscreen support for imx7d-sdb, SAI audio and LCD support for
imx6ul-14x14-evk, gpio power off support for imx6q-bx50v3, etc.
- Update the boards from Freescale/NXP to use WDOG_B pin for reset
- PCI reset polarity correction for imx6qdl-sabresd and imx6q-tbs2910
- Update i.MX board dts files to use generic uart-has-rtscts DT
property instead of vendor specific one
- DTC warning fixing for a few boards which are mostly mismatch between
unit-address and reg property
- Remove SION setting from all mux modes on i.MX25
* tag 'imx-dt-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (47 commits)
ARM: dts: imx7: add Toradex Colibri iMX7S/iMX7D support
ARM: dts: imx7d: move input header into base device tree
ARM: dts: imx7d: recreate imx7d.dtsi with i.MX 7Dual specifics
ARM: dts: imx7d: use imx7s.dtsi as base device tree
ARM: dts: imx7d-sdb: Add support for touchscreen
ARM: dts: imx7d-sdb: Add display support
ARM: dts: imx7d: Add SPI support
ARM: dts: imx6q-bx50v3: Add gpio power off support
ARM: dts: imx6ul-pico-hobbit: Fix Ethernet PHY reset GPIO
ARM: dts: imx6q-tbs2910: fix pcie reset polarity
ARM: dts: imx6sx-sdb: Use WDOG_B pin reset
ARM: dts: imx6ul-evk: Use WDOG_B pin reset
ARM: dts: imx7d-sdb: Use WDOG_B pin reset
ARM: dts: imx6qdl-sabresd: Use WDOG_B pin reset
ARM: dts: utilite-pro: add mmc card slot support
ARM: dts: imx6q-cm-fx6: fix the operation points
ARM: dts: imx6qdl.dtsi: add "arm,shared-override" for pl310
ARM: imx25-pinfunc: remove SION from all modes
ARM: imx25-pinfunc: document SION being important for MX25_PAD_SD1_CMD__SD1_CMD
ARM: dts: ls1021a: Add dis_rxdet_inp3_quirk property to USB3 node
...
Signed-off-by: Olof Johansson <olof@lixom.net>
DT so that the firmware can tell us its MAC address.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABCgAGBQJXea5HAAoJELXWKTbR/J7ofl4P/36ReBOwgWtXa2h/kDAU9cjM
lAaFedQ4GesRRPNkFboyO5YM05H1EnyVSmbJglpCRVsQI0STph/NXGmTH+tIN29L
iC/pJw1Nz1rQOhQDdDch5xhqC1lgfZ7g4PFmDuTJr9NTLFcOKQVsxSmBMqDZSbxC
bWrlUW6YdZBK7tUfK4lf6p9tAnpNeYyn3VGXPKb2l49DcwZfZgU6D28mmH4/PfHc
KB5cNUfEEE3wt6DtCB6cWsqwPlofwyz/62NP1kwotMFbFRrHmraVVkR08OdrfxwJ
I2Q/tD+ztc8/FQq5hQYHfxSX9RXNmRutrRZYJlT6hwPAAue91uy9r9jYMCl6hwm3
7zG32GU7SL8mqUdYLjVnZ6H8vqc7+GUf0hdz46vnXDLwquawWMmOory7PX1fgXJc
pLiaUtfRvYd2RmMSsbm7QCdQu1yQ93Q3ytcAJsDCq2fJ+ySMpHWgQ+El3yRKmnIk
fr4c5e1qqMutEfbl4hirU8Dg9dx0KbQDoY3L1e+sRQRSy9YppRHD2Lw3pOKlY3X6
NUUvvoAfjDwDHNCJQAi2n9FRxlhhrUNynFlGfsjXXDOZHtFpOGC4zOEgMXr2uMNm
r1qYNiB03vhYVHFfUsNDtD8LSmSQ3FEmMMvL4fhKjRsjYuLHccPs7H5l+Oq45OH0
OndYBA60urgkG2QnonR3
=byP6
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=AyiN
-----END PGP SIGNATURE-----
Merge tag 'bcm2835-dt-next-2016-07-03' into devicetree/next
This pull request brings in the change to describe the ethernet in the
DT so that the firmware can tell us its MAC address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Two patches fixing simplefb on the SoCs that had their display clocks
enabled, and one fix for the CHIP that will enable its sched clock.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tU7Y
-----END PGP SIGNATURE-----
Merge tag 'sunxi-fixes-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into fixes
Pull "Allwinner Fixes for 4.7" from Maxime Ripard:
Two patches fixing simplefb on the SoCs that had their display clocks
enabled, and one fix for the CHIP that will enable its sched clock.
* tag 'sunxi-fixes-for-4.7' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux:
ARM: dts: sun7i: Fix pll3x2 and pll7x2 not having a parent clock
ARM: dts: sunxi: Add pll3 to simplefb nodes clocks lists
ARM: sunxi/dt: make the CHIP inherit from allwinner,sun5i-a13
The auxtek t004 has its otg usb vbus hardwired to 5v (likely in case
people use it to power the board instead of the dedicated power micro
usb connector), it does have an id pin, so it allows full otg
functionality.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
- PWM binding updates and related dts changes
- OCM RAM updates for dra7
- Enable n900 lirc-rx51 driver
- omap3-gta04 updates for backlight, bma180, itg3200, hmc5843 and wifi
- am335x, am437x and am57xx operating point updates and additions
- am335x-icev2 pca9536 node
- dra72-evm regulator updates
- edma spelling fixes
- am335x and am437x ethernet phy update
- a series of mcbsp updates
- omap3-gta04 eeprom
- dra7 PCIe unit address fix
- stdout-path for beaglebone variants
- crypto accelerator nodes for am335x, am437x and dra7
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2xdp
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Device tree changes for omaps for v4.8 merge window:
- PWM binding updates and related dts changes
- OCM RAM updates for dra7
- Enable n900 lirc-rx51 driver
- omap3-gta04 updates for backlight, bma180, itg3200, hmc5843 and wifi
- am335x, am437x and am57xx operating point updates and additions
- am335x-icev2 pca9536 node
- dra72-evm regulator updates
- edma spelling fixes
- am335x and am437x ethernet phy update
- a series of mcbsp updates
- omap3-gta04 eeprom
- dra7 PCIe unit address fix
- stdout-path for beaglebone variants
- crypto accelerator nodes for am335x, am437x and dra7
* tag 'omap-for-v4.8/dt-part1-signed-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (42 commits)
ARM: dts: AM43xx: Add node for RNG
ARM: dts: AM43xx: clk: Add RNG clk node
ARM: dts: DRA7: Add DT node for RNG IP
ARM: dts: DRA7: Add support for SHA IP
ARM: dts: DRA7: Add DT nodes for AES IP
ARM: dts: DRA7: Add DT node for DES IP
ARM: dts: am335x-bone-common: use stdout-path in Beaglebone boards.
ARM: dts: DRA7: fix unit address of second PCIe instance
ARM: dts: omap3-gta04: Add RFID eeprom node
ARM: dts: omap4-duovero: Add pdmclk binding for audio
ARM: dts: omap4-var-som-om44: Add pdmclk binding for audio
ARM: dts: omap4-sdp: Add pdmclk binding for audio
ARM: dts: omap4-panda-common: Add pdmclk binding for audio
ARM: dts: omap5-board-common: Add pdmclk binding for audio
ARM: dts: omap3: Add clocks to McBSP nodes
ARM: dts: am335x-bone-common: Mark MAC as having only one PHY
ARM: dts: am437x-idk-evm: Mark MAC as having only one PHY
ARM: dts: Correct misspelling, "emda3" -> "edma3"
ARM: dts: dra72-evm: Rename 3.3V regulator tag
ARM: dts: am335x-icev2: Add DT node for TI PCA9536
...
Signed-off-by: Olof Johansson <olof@lixom.net>
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
-----BEGIN PGP SIGNATURE-----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=F38N
-----END PGP SIGNATURE-----
Merge tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/dt
DT Changes for 4.8 #2:
- New board: at91sam9260ek
- Fixes for the sam9_l9260
- Sama5d2 Xplained PMIC fix
- Addition of the PMU node for the sama5d2
* tag 'at91-ab-4.8-dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
ARM: dts: at91: sama5d2_xplained: Update the pmic node
ARM: dts: at91: sama5d2: add PMU node
ARM: dts: at91: sam9_l9260: Modify information in LED nodes.
ARM: dts: at91: sam9_l9260: Add pinctrl information to ethernet node.
ARM: dts: at91: add at91sam9260ek board DT
Signed-off-by: Olof Johansson <olof@lixom.net>
In order to be able to properly generate its pixel clock, the pll3-2x fixed
factor needs to be able to change the PLL3 rate too.
Add the needed extra compatible so that it behaves that way.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds all the mod1 clocks available on A20 to its device
tree. This list was created by looking at the A20 user manual.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The a10s mk802 uses a rtl8189es sdio wifi chip, add a node enabling
the mmc1 controller, this enables using the wifi chip (together with
an out of tree sdio driver for it).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the axp152 pmic to the mk802 dts, note there are
no regulator nodes as we do not yet support the regulators on the
axp152.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the otg controller, the id pin is not connected so enable
it in peripheral only mode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a proper binding for Ethernet switches hanging off
different buses, and a driver for the BCM53125 switch, add its Device
Tree as a child MDIO node, at MDIO address 30 (Broadcom pseudo-PHY
address) and describe the ports layout of the Lamobo R1 board.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Parrot Board is an evaluation board with an Allwinner R16 (assumed
to be close to an Allwinner A33), 4GB of eMMC, 512MB of RAM, USB host
and OTG, a WiFi/Bluetooth combo chip, a micro SD Card reader, 2
controllable buttons, an LVDS port with separated backlight and
capacitive touch panel ports, an audio/microphone jack, a camera CSI
port, 2 sets of 22 GPIOs and an accelerometer.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The early A13 Q8 tablets all use a Realtek WiFi module connected to
USB1. The module is powered by AXP209's LDO3 at 3.3V.
Move the related settings from sun5i-a13-q8-tablet.dts to
sun5i-q8-common.dtsi, for all q8-based tablets.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the Bananapi M1 Plus A20 development board from
sinovoip.com.cn . This board is nearly a clone of the Lemaker's
Bananapro, but differ with the wlan chipset connection and i2s pinout.
And I also enable the integrated audio codec on default.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some of the sun8i q8 boards have an usb wifi controller, on other
variants this will result in an used usb root-hub, but the best
way to deal with wifi on this boards is to simply let the kernel
auto-detect usb or sdio wifi controllers.
This has been tested on an a23 based q8 tablet with a RTL8188ETV wifi
controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the mmc nodes above the ohci nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move the &pio node below the mmc nodes for proper ordering by name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add NAND Flash controller node definition to the A20 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add NAND Flash controller node definition to the A10 SoC.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pmic / regulator nodes to Mele M9 dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add pmic / regulator nodes to Mele A1000G quad dts.
Note both reg_usb1_vbus and reg_dldo4 need to be on for the hub attached
to usb1 to work, and we can list only one usb1_vbus-supply, so dldo4 is
marked as regulator-always-on.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The blue led on the Mele M9 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to m9:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from m9:blue:usr to a1000g:blue:pwr (fixing a copy
and paste error in the prefix while at it) and marks it as default on,
fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The blue led on the Mele A1000 is wired to light up as soon as the board
has powered (it will be on while the gpio is still in input / floating
mode), also its location on the top-set box clearly signals "power led".
Until now we've been treating this as a generic usr function led, which
means that when you plug power into the top-set box, the power-led lights
and then turns off as soon as the kernel loads, which looks wrong.
This renames the led from a1000:blue:usr to a1000:blue:pwr and marks
it as default on, fixing this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
The Polaroid mid2809pxe04 tablet uses an sdio esp8089 wifi chip, so
ehci0 is not used and should be disabled.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we've all the necessary bits in place we can enable
full otg support on these tablets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the drivebus regulator which is an (optional)
part of the axp221/axp223 pmic. Since this regulator may not be
available at all depending on the board, mark it as disabled by
default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a node describing the (optional) usbpower-supply of the
axp221 / axp223 pmic.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Use of these as regulators conflicts with use of the gpio pins as
gpios, so disabled the ldo_io# regulators by default, this avoids
the regulator core touching them when the pins are used as gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.
While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Update the simplefb nodes for hdmi / tv-encoder out to point to
tcon0_ch1 instead of tcon0_ch0 as tcon clock.
While at it fix the clocks lines being longer than 80 chars.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that recent kernels have a shorter timeout when scanning for
ethernet phys causing us to hit a timeout on boards where the phy's
regulator gets enabled just before scanning, which leads to non working
ethernet.
A 10ms startup delay seems to be enough to fix it, this commit adds a
20ms startup delay just to be safe.
This has been tested on a sun4i-a10-a1000 and sun5i-a10s-wobo-i5 board,
both of which have non-working ethernet on recent kernels without this
fix.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sunxi-common-regulators.dtsi provided dummy regulators vcc3v0, vcc3v3,
vcc5v0. 3.0V/3.3V and 5.0V are commonly used voltages in Allwinner
devices. These dummy regulators provide a stand-in when bindings that
require one, but the real regulator is not supported yet.
Since these are no longer needed, we can drop the include file by
copying over reg_usb1_vbus.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems that the wifi chip is powered by both ldo3 and ldo4 tied
together and that using only one results in the wifi-chip dropping of
the USB bus sometimes.
Ideally we would have a proper way of modelling this (this is being
worked on), but currently we do not. This is not an issue since we need
to keep these regulators always-on anyways, due to these boards
crashing when ldo3/4 get turned back on after having been turned off.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The BPI-M2+ is an H3 development board. It is a smaller form factor than
the original BPI-M2, with the new H3 SoC.
It has 1GB DRAM, 8GB eMMC, a micro SD card slot, HDMI output, 2 USB
host connector and 1 USB OTG connector, an IR receiver, WiFi+BT based
on Ampak AP6212.
The board also has a 3 pin header for (debug) UART, a 40 pin GPIO header
based on the Raspberry Pi B+, but the peripheral signals are not the
same, and an FPC connector for connecting BPI's camera.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Move uart0 pins to sort the list of pin settings in alphabetical order.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is connected
to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is the primary PMIC. It provides various supply voltages
for the SoC and other peripherals. The PMIC's interrupt line is
connected to NMI pin of the SoC.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The AXP809 PMIC is used with the Allwinner A80 SoC, along with
an AXP806 PMIC as a slave.
This patch adds a dtsi file for all the common bindings and default
values unrelated to board design. Currently this is just listing all
the regulator nodes. The regulators are initialized based on their
device node names.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
spi2 is available on the UEXT connector
Signed-off-by: Michal Suchanek <hramrach@gmail.com>
[Maxime: Fixed the node order]
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Q8 form factor A13 tablets have a 7" LCD panel. Unfortunately we
don't know the exact model of the panel. Just pick a panel with
display timings close to what we know.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Q8 tablets use the audio codec to provide audio output via a
headphone jack or a small mono speaker. A GPIO output is used to
control speaker amp.
The tablets may or may not have an internal microphone.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A13 Q8 tablets, the PMIC's USB power supply (VBUS) is connected
to the external OTG port. This can be used to provide power and OTG VBUS
sensing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The output pin of LDO is also a GPIO pin, and the on/off settings of the
regulator are actually pinmux settings.
Disable it by default so it doesn't conflict with GPIO usage.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Most of the display engine is shared between the R8 and the A13. Move the
common parts to the Á13 DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The RGB bus can be used in several configurations, one of which being the
RGB666.
Add a pinctrl group for that case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Enable the display and TCON clocks that are needed to drive the display
engine, tcon and TV encoders.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Due to introducing the new driver - ACT8945A MFD drive,
change the pmic device node to align with the ACT8945A
regulator and charger drivers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add power led node and rename status led node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add missing pinctrl information to ethernet node.
Signed-off-by: Raashid Muhammed <raashidmuhammed@zilogic.com>
Reviewed-by: Vijay Kumar B. <vijaykumar@bravegnu.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add Device Tree source file for at91sam9260ek board. This official Atmel
Evaluation Kit is designed around a SoC based on a ARM 926 core the
at91sam9260.
The board is also added to the dts Makefile.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Add the device tree nodes for the Advanced Power Management Unit (APMU)
and the second Cortex-A15 CPU core.
Use the "enable-method" prop to point out that the APMU should be used
for the SMP support.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DT nodes for the Advanced Power Management Unit (APMU) and the
second CPU core. Use the enable-method to point out that the APMU
should be used for SMP support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a DT node for the Advanced Power Management Units (APMU), and use
the enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add DT nodes for the Advanced Power Management Units (APMU), and use the
enable-method to point out that the APMU should be used for SMP
support.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC4 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a "serial1" alias for the serial console (it is labeled "uart1").
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameter from the kernel command line, as it's no
longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC2 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Change the console alias to "serial0", for consistency with other
boards (the first unlabeled serial port is always called "serial0").
This does change the serial console from /dev/ttySC1 to /dev/ttySC0.
Add the serial port config to "chosen/stdout-path", which requires
referring to the port by alias.
Drop the "console=" parameters from the kernel command line, as they're
no longer needed for DT-based platforms.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The PMIC driver used to register itself as poweroff controller by
default, hence assuming that this device is using the PMIC as
system power controller.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch fixes the following DTC warnings for am57xx-sbc-am57x.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-igep0050.dtb,
omap5-sbc-t54.dtb and omap5-uevm.dtb:
"connector@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap5-cm-t54.dtb:
"connector@0 has a unit name, but no reg property"
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-sbc-t43.dtb:
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am437x-gp-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am43xx-epos-evm.dtb:
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-var-dvk-om44.dtb
and omap4-var-stk-om44.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-sdp.dtb
and omap4-sdp-es23plus.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-panda.dtb,
omap4-panda-a4.dtb and omap4-panda-es.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"encoder@1 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap4-duovero-parlor.dtb:
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-thunder.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-sbc-t3517.dtb,
omap3-sbc-t3530.dtb and omap3-sbc-t3730.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-pandora-600mhz.dtb
and omap3-pandora-1ghz.dtb:
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-overo-summit.dtb,
omap3-overo-storm-tobi.dtb, omap3-overo-storm-summit.dtb and
omap3-overo-tobi.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-igep0020.dtb
and omap3-igep0020-rev-f.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-overo-gallop43.dtb,
omap3-overo-chestnut43.dtb, omap3-overo-storm-chestnut43.dtb,
omap3-overo-palo43.dtb, and omap3-overo-storm-palo43.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-ha-lcd.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-gta04a3.dtb,
omap3-gta04a4.dtb and omap3-gta04a5.dtb:
"dmtimer-pwm@11 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-devkit8000-lcd43.dtb
and omap3-devkit8000-lcd70.dtb:
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-devkit8000.dtb,
omap3-devkit8000-lcd43.dtb and omap3-devkit8000-lcd70.dtb:
"encoder@0 has a unit name, but no reg property"
"endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-cm-t3517.dtb,
omap3-cm-t3530.dtb and omap3-cm-t3730.dtb:
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-beagle-xm.dtb:
"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-beagle.dtb:
"encoder@0 has a unit name, but no reg property"
"encoder@0/ports/port@0/endpoint@0 has a unit name, but no reg property"
"encoder@0/ports/port@1/endpoint@0 has a unit name, but no reg property"
"connector@0 has a unit name, but no reg property"
"connector@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap3-n900.dtb:
"dmtimer-pwm@9 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"dmtimer-pwm@10 has a unit name, but no reg property"
"display@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for am3517-craneboard.dtb:
"fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for omap2430-sdp.dtb:
"func_96m_ck has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix pll3x2 and pll7x2 not having a parent clock, specifically this
fixes the kernel turning of pll3 while simplefb is using it when
uboot has configured things to use pll3x2 as lcd ch clk parent.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add support for the Broadcom BCM953012 Enterprise Router reference
board, enable the following peripherals:
- UART0 (UART1 is not populated)
- WPS and restart GPIO buttons
- Ethernet switch w/ only two facing ports
- NAND flash
- SPI-NOR flash
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add "ti,cpsw-mdio" for am335x/am437x/dra7 SoCs where MDIO is
implemented as part of TI CPSW and, this way, enable PM runtime auto
suspend for Davinci MDIO driver on these paltforms.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Computer on Module Colibri iMX7S/iMX7D along
with the development/evaluation carrier board device trees. Follow
the usual hierarchic include model, maintaining shared configuration
in imx7-colibri.dtsi and imx7-colibri-eval-v3.dtsi respectively.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The base device tree uses KEY_POWER in the snvs-powerkey node,
hence include the input.h header file in the base device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7Solo implements a subset of features available on
i.MX 7Dual. Recreate imx7s.dtsi as the base device tree for
i.MX 7Dual boards. The i.MX 7Dual's additional features over
i.MX 7Solo are:
- Second Cortex-A7 core
- Second Gigabit Ethernet controller
- EPD (Electronc Paper Display, not yet part of the device tree)
- PCIe (not yet part of the device tree)
- Additional USB2.0 OTG controller
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The i.MX 7 series currently consists of two SoCs: i.MX 7Solo and
7Dual. The former has a subset of features of the latter, hence
use imx7s.dtsi as the new base device tree. To keep diffstat nice,
just move imx7d.dtsi to imx7s.dtsi temporarily and recreate
imx7d.dtsi in a second commit.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
bx50v3 boards can be powered off via GPIO, this patch specifies the GPIO to
be used with the gpio-poweroff driver.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add support for cortex-a7-pmu present on ipq4019 SoCs.
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This is the first Dragonboard based on APQ8060 and PM8058. It
was produced in 2011 in cooperation between Qualcomm and
BSQUARE.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
There is currently a fixed regulator in the .dtsi file for
the MSM8660 chipset, used by the SURF board. We want to define
real regulators for a board using this chipset, so push the fixed
regulator down to the SURF board which is the only user.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The RTC was defined on 0x11d but on the MSM8660/APQ8060 it is
actually on 0x1e8. We were saved by the fact that the driver does
not use the reg parameter: instead it uses the compatible string
to figure out where the RTC is.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The I2C block on the GSBI12 is used on the APQ8060 Dragonboard for
sensors. Make it available in the chipset file.
Take this opportunity to fix the IRQ flag "0" to "NONE" using the
IRQ DT include.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the L2CC IPC resource and RPM devices plus the nodes
for the PM8901 and PM8058 regulators to the MSM8660 device tree.
This was tested on the APQ8060 Dragonboard.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The SDCC5 SD/MMC controller is used for a second uSD slot
on the APQ8060 Dragonboard. On most other systems it is just
dark silicon so define it and leave it as "disabled" in the core
SoC file.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This adds the 8660 PMIC GPIO and MPP blocks to the MSM8660
DTSI. Verified against the vendor tree to be in these locations
with these interrupts, tested on the APQ8060 Dragonboard.
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Since the pmic8xxx-pwrkey driver is already supported in the
qcom-apq8064.dtsi, and the pmic8xxx-pwrkey supports logic to
configure proper device shutdown when ps_hold goes low, it is
better to use that driver then a generic gpio button.
Thus this patch remove the gpio power key entry here, so we
don't get double input events from having two drivers enabled.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch updates the qcom,state-cells to qcom,smem-state-cells to
match recent changes to the binding.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch adds the qcom,controlled-remotely property for the blsp2_bam
controller node. This board requires this, otherwise the board fails to
boot due to access of protected registers during BAM initialization.
Fixes: 62bc817922 dts: msm8974: Add blsp2_bam dma node
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
This board locks up if we stress test the eMMC, as the regulator s4 is
unable to supply enough current for all the peripherials attached to it.
As this supply is wired up to most of the peripherials including DDR,
it resulted in such lockup.
This patch fixes this issue by setting s4 regulator correctly with
Auto power mode.
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
[Srinivas Kandagatla: rewrote the change log]
Tested-by: Girish Sharma <girish.sharma@einfochips.com>
Signed-off-by: Parth Pancholi <parth.pancholi@einfochips.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This board has been renamed recently and announced at
https://eragon.einfochips.com/products/sd-600eval.html
So rename this board files so that it reflects actual product in market.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch move sdcc3 pinctrl nodes out of board file, so that
other boards do not duplicate the same thing.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This patch moves out the sdcc1 pinctrl nodes out of board files to soc file,
so that it will be duplicated in other board files.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Initial release for rk3229 evb board, and turn the GMAC on.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We have the brother chipset that RK3228 and RK3229, they share most
of dts configuration, but there are a number of different features.
In order to develop the future when they are easy to distinguish,
we need them to be independent.
Signed-off-by: Xing Zheng <zhengxing@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add the DT node for the random number generator peripheral.
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
- dts: rename 'ide-disk' to 'disk-activity'
- platform: rename 'ide-disk' to 'disk-activity'
- defconfig: rename 'LEDS_TRIGGER_IDE_DISK' to 'LEDS_TRIGGER_DISK'
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Various I/O memory fix for Cortex A9 based SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAldo+JYACgkQCwYYjhRyO9XI5QCglOxAOJSamD5IgIpMklk/5ZpG
/MEAn0j80ClwN+YB+/eii/iUMwHwMDQe
=iyoH
-----END PGP SIGNATURE-----
Merge tag 'mvebu-fixes-4.7-1' of git://git.infradead.org/linux-mvebu into fixes
mvebu fixes for 4.7 (part 1)
Various I/O memory fix for Cortex A9 based SoCs
* tag 'mvebu-fixes-4.7-1' of git://git.infradead.org/linux-mvebu:
ARM: dts: armada-38x: fix MBUS_ID for crypto SRAM on Armada 385 Linksys
ARM: mvebu: map PCI I/O regions strongly ordered
ARM: mvebu: fix HW I/O coherency related deadlocks
Signed-off-by: Olof Johansson <olof@lixom.net>
Describe JPEG Processing Unit (JPU) in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add JPU clock and its parent, M2 clock to the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the (previously omitted) DU pin data to the SILK board's device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Commit 3939f33450 ("ARM: 8418/1: add boot image dependencies to
not generate invalid images") fixed bad image generation for the
parallel building, but as its side effect, Kbuild now descends into
arch/arm/boot/ again and again, duplicating the log messages.
It looks clumsy, so let's display the same message only once.
This commit moves the log rules from arch/arm/boot/Makefile to
arch/arm/Makefile. I did not delete them completely because *Image
are the final targets that users are interested in.
Without this commit, the log of incremental build is like follows:
$ make ARCH=arm UIMAGE_LOADADDR=0x80208000 uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
CHK include/generated/bounds.h
CHK include/generated/timeconst.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Image arch/arm/boot/uImage is ready
With this commit, it will look like follows:
$ make ARCH=arm UIMAGE_LOADADDR=0x80208000 uImage
CHK include/config/kernel.release
CHK include/generated/uapi/linux/version.h
CHK include/generated/utsrelease.h
CHK include/generated/bounds.h
CHK include/generated/timeconst.h
CHK include/generated/asm-offsets.h
CALL scripts/checksyscalls.sh
CHK include/generated/compile.h
Kernel: arch/arm/boot/Image is ready
Kernel: arch/arm/boot/zImage is ready
Kernel: arch/arm/boot/uImage is ready
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now that we've a clock node describing pll3 we must add it to the
simplefb nodes clocks lists to avoid it getting turned off when
simplefb is used.
This fixes the screen going black when using simplefb.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Adding dt node for hardware random number generator IP.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC has the same SHA IP as OMAP5. Add DT entry for the same.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: changed SHA to use EDMA instead of SDMA]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DRA7 SoC has the same AES IP as OMAP4. Add DT entries for both AES cores.
Signed-off-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[t-kristo@ti.com: squashed in the change to use EDMA, squashed in
support for two AES cores]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit adds the stdout-path propety in /chosen for all Beaglebone
boards.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
- Chris provides documentation and DTS fixes for the bcm11351 CPU enable-method in preparation
for adding support for the BCM23550 SoC and its corresponding documentation, SoC dtsi
and the Sparrow board DTS file
- Jon adds MSI support to the PCI nodes, updates the secondary cores boot address for the B0
production revision of the Northstar Plus SoC, adds a DTS for the BCM958625HR board, another
one for the BCM958525XMC board, and finally adds the PL330 DMA controller to the NSP DTS
- Rafal enables the SPI NOR flash on dual flash systems (NAND + SPI) on the BCM5301x SoCs
and devices
- Florian adds support for the BCM5301x built-in Ethernet switch by adding nodes for the
Gigabit MAC controllers and the Switch Register Access block, and finally updates the
SmartRG SR-400AC board with its switch port layout
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=0GWx
-----END PGP SIGNATURE-----
Merge tag 'arm-soc/for-4.8/devicetree' of http://github.com/Broadcom/stblinux into next/dt
This pull request contains Device Tree changes for Broadcom ARM-based SoCs:
- Chris provides documentation and DTS fixes for the bcm11351 CPU enable-method in preparation
for adding support for the BCM23550 SoC and its corresponding documentation, SoC dtsi
and the Sparrow board DTS file
- Jon adds MSI support to the PCI nodes, updates the secondary cores boot address for the B0
production revision of the Northstar Plus SoC, adds a DTS for the BCM958625HR board, another
one for the BCM958525XMC board, and finally adds the PL330 DMA controller to the NSP DTS
- Rafal enables the SPI NOR flash on dual flash systems (NAND + SPI) on the BCM5301x SoCs
and devices
- Florian adds support for the BCM5301x built-in Ethernet switch by adding nodes for the
Gigabit MAC controllers and the Switch Register Access block, and finally updates the
SmartRG SR-400AC board with its switch port layout
* tag 'arm-soc/for-4.8/devicetree' of http://github.com/Broadcom/stblinux:
ARM: dts: BCM5310x: Enable switch ports on SmartRG SR400AC
ARM: dts: BCM5301X: Add SRAB interrupts
ARM: dts: Enable SRAB switch and GMACs on 5301x DTS
ARM: dts: NSP: Add PL330 support
ARM: dts: NSP: Add XMC board support
ARM: dts: bcm23550: Add device tree files
Documentation: devicetree: Document BCM23550 bindings
ARM: BCM5301X: Enable SPI-NOR on dual flash devices
ARM: dts: NSP: Add new DT file for bcm958625hr
ARM: dts: NSP: modify second CPU address
ARM: dts: NSP: Add MSI support on PCI
ARM: BCM: modify Broadcom CPU enable method
ARM: dts: fix use of bcm11351 enable method
Documentation: Binding docs for bcm11351 enable method
Signed-off-by: Olof Johansson <olof@lixom.net>
- Fix dra7 for hardware issues limiting L4Per and L3init power domains
to on state. Without this the devices may not work correctly after
some time of use because of asymmetric aging. And related to this,
let's also remove the unusable states.
- Always select omap interconnect for am43x as otherwise the am43x
only configurations will not boot properly. This can happen easily
for any product kernels that leave out other SoCs to save memory.
- Fix DSS PLL2 addresses that have gone unused for now
- Select erratum 430973 for omap3, this is now safe to do and can
save quite a bit of debugging time for people who may have left
it out.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mQyc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Fix dra7 for hardware issues limiting L4Per and L3init power domains
to on state. Without this the devices may not work correctly after
some time of use because of asymmetric aging. And related to this,
let's also remove the unusable states.
- Always select omap interconnect for am43x as otherwise the am43x
only configurations will not boot properly. This can happen easily
for any product kernels that leave out other SoCs to save memory.
- Fix DSS PLL2 addresses that have gone unused for now
- Select erratum 430973 for omap3, this is now safe to do and can
save quite a bit of debugging time for people who may have left
it out.
* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
ARM: dts: DRA74x: fix DSS PLL2 addresses
ARM: OMAP2: Enable Errata 430973 for OMAP3
+ Linux 4.7-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=P0Vi
-----END PGP SIGNATURE-----
Merge tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
ARM: OMAP2+: timer: add probe for clocksources
ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
arm: Use _rcuidle for smp_cross_call() tracepoints
arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch fixes a non-booting issue in Mainline.
When booting with a compressed kernel, we need to be careful how we
populate memory close to DDR start. AUTO_ZRELADDR is enabled by default
in multi-arch enabled configurations, which place some restrictions on
where the kernel is placed and where it will be uncompressed to on boot.
AUTO_ZRELADDR takes the decompressor code's start address and masks out
the bottom 28 bits to obtain an address to uncompress the kernel to
(thus a load address of 0x42000000 means that the kernel will be
uncompressed to 0x40000000 i.e. DDR START on this platform).
Even changing the load address to after the co-processor's shared memory
won't render a booting platform, since the AUTO_ZRELADDR algorithm still
ensures the kernel is uncompressed into memory shared with the first
co-processor (0x40000000).
Another option would be to move loading to 0x4A000000, since this will
mean the decompressor will decompress the kernel to 0x48000000. However,
this would mean a large chunk (0x44000000 => 0x48000000 (64MB)) of
memory would essentially be wasted for no good reason.
Until we can work with ST to find a suitable memory location to
relocate co-processor shared memory, let's disable the shared memory
nodes. This will ensure a working platform in the mean time.
NB: The more observant of you will notice that we're leaving the DMU
shared memory node enabled; this is because a) it is the only one in
active use at the time of this writing and b) it is not affected by
the current default behaviour which is causing issues.
Fixes: fe135c6 (ARM: dts: STiH407: Move over to using the 'reserved-memory' API for obtaining DMA memory)
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
There is no reason to hold s/w dependent parameter in device tree.
Even more, there is no reason in this parameter because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels
anyway.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on the latest timing specifications for the TPS65218 from the data
sheet, http://www.ti.com/lit/ds/symlink/tps65218.pdf, document SLDS206
from November 2014, we must change the i2c bus speed to better fit within
the minimum high SCL time required for proper i2c transfer.
When running at 400khz, measurements show that SCL spends
0.8125 uS/1.666 uS high/low which violates the requirement for minimum
high period of SCL provided in datasheet Table 7.6 which is 1 uS.
Switching to 100khz gives us 5 uS/5 uS high/low which both fall above
the minimum given values for 100 khz, 4.0 uS/4.7 uS high/low.
Without this patch occasionally a voltage set operation from the kernel
will appear to have worked but the actual voltage reflected on the PMIC
will not have updated, causing problems especially with cpufreq that may
update to a higher OPP without actually raising the voltage on DCDC2,
leading to a hang.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to use Wake-on-Lan on RK3288 integrated MAC, we need to wake-up
the CPU on the PMT interrupt when the MAC and the PHY are in low power mode.
Adding the interrupt declaration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sata support to the Northstar Plus SoC device tree.
Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the support for the Marvell crypto engine was added in the Device
Tree of the various Armada 385 Device Tree files in commit
d716f2e837 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x
boards"), a typo was made in the MBus window attributes for the Armada
385 Linksys board: 0x09/0x05 are used instead of 0x19/0x15. This commit
fixes this typo, which makes the CESA engines operational on Armada 385
Linksys boards.
Reported-by: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Terry Stockert <stockert@inkblotadmirer.me>
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: <stable@vger.kernel.org>
Fixes: d716f2e837 ("ARM: mvebu: define crypto SRAM ranges for all armada-38x boards")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
The sun4i-timer driver registers its sched_clock only if the machine is
compatible with "allwinner,sun5i-a13", "allwinner,sun5i-a10s" or
"allwinner,sun4i-a10".
Add the missing "allwinner,sun5i-a13" string to the machine compatible.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 465a225fb2 ("ARM: sun5i: Add C.H.I.P DTS")
Cc: <stable@vger.kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
According to the imx6ul-pico-hobbit schematics the Ethernet PHY reset GPIO
is GPIO1_28, so fix it accordingly.
Also adjust the reset duration to 1ms, because the KSZ8081 datasheet
requires 500μs.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
According to Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt the
polarity of "reset-gpio" is assumed to be active-low unless a separate
property "reset-gpio-active-high" is available. So replace the inconsistent
polarity description to make the correct active-low reset behavior more
obvious.
Signed-off-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6sx-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6ul-evk has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx7d-sdb has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
imx6qdl-sabresd has WDOG2_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The Utilite Pro has a mmc card slot connected to the usdhc3
controller. There is no card detection until hardware revision 1.3.
Add support for it and signal the controller with the broken-cd
property that polling has to be used to detect a card.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The current ldo settings of the cm-fx6 do not allow 1.2GHz cpu
frequency. At this frequency the module behaves unstable.
But the imx6q fuse indicates that 1.2GHz operation is possible.
Hence, remove the 1.2GHz operation point in the device tree.
Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
[christopher.spinrath@rwth-aachen.de: enhance commit message, adjust
remaining operation points to match the ones in imx6q.dtsi and add
a comment in the device tree]
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6 SMP system has the same DMA memory coherency issue [1] with
pl310 L2 controller. With this shared override bit set, the customer
reports the DMA coherency issue is gone. Besides, I have tested
the performance using USB ethernet with/without this bit, it shows
no difference.
[1] http://patchwork.ozlabs.org/patch/469362/
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
R8A7792 SoC doesn't have the EtherMAC core, so SMSC LAN89218 Ethernet
chip was used instead on the Blanche board; this chip is compatible with
SMSC LAN9115 for which there's a (device tree aware) driver. Describe
the chip in the Blanche device tree; enable DHCP and NFS root in the
kernel command line for the kernel booting.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add the initial device tree for the R8A7792 SoC based Blanche board.
The board has 2 debug serial ports: SCIF0 and SCIF3; include support for
them, so that the serial console can work.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the IRQC interrupt controller in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe [H]SCIFs in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe SYS-DMAC0/1 in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The initial R8A7792 SoC device tree including CPU cores, GIC, timer, SYSC,
and the required clock descriptions.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
With the SION bit set a pin can be read as GPIO even though it's not muxed
as GPIO. This is useful at times. The downside however is that the signal
is not only routed to the GPIO IP but also all other IPs that can make use
of the pin. This resulted in more than one issue for me in the past. Things
like spi transfers that result in usb reenumeration or setting a GPIO to a
value that triggers an RTS irq for an UART.
This convinces me that the SION bit does more harm than good and so all
SION bits are removed that are not known to be needed.
Note that this has no influence on GPIOs under Linux as the gpio-mxc
driver just reports the level the pin is driven to for outputs and not
the level as seen on the pin.
If this commit introduces a regression for you, please report which SION
bit is essential for your setup.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Update DTSI file to add the reset controller node.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
On these two boards, the serial0 is used for inter-chip connection,
so cannot be used for login console. The serial2 is used instead
for them, but it is tedious to use because upper level deployment
projects must switch login console per board.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This node consists of various system-level configuration registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This pin-muxing is needed to get access to the UniPhier System Bus.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Name the Pin Function Controller subnode for SCIFA4 after its device
name, instead of after the serial port alias.
This avoids conflicts when adding support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF2 after its device
name, instead of using some arbitrary name that looks like a serial port
alias, but differs from the actual alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for QSPI after its device name,
instead of after the spi interface alias.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for QSPI and MSIOF0 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF0 and SCIF1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for VIN1 after its device name,
instead of using the generic and indexless "vin".
This avoids conflicts when enabling support for more video inputs later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for QSPI and MSIOF1 after
their device names, instead of after the spi interface aliases.
This avoids conflicts when enabling support for more spi interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF0 and SCIFA1 after
their device names, instead of after the serial port aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnodes for SCIF2 and SCIF4 after
their device names, instead of using some arbitrary names that look like
serial port aliases, but differ from the actual aliases.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIF0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIFA1 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for MMC0 after its device name,
instead of using the generic and indexless "mmc".
This avoids conflicts when enabling support for more MMC interfaces
later, either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Name the Pin Function Controller subnode for SCIFA0 after its device
name, instead of after the serial port alias.
This avoids conflicts when enabling support for more serial ports later,
either here or in a DT overlay.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
4.7-rc1 because OF graph logic expects specific names of child nodes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ro/B
-----END PGP SIGNATURE-----
Merge tag 'samsung-fixes-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into fixes
Fixes for Exynos-based Snow and Peach Pit boards for regressions introduced in
4.7-rc1 because OF graph logic expects specific names of child nodes.
* tag 'samsung-fixes-4.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
ARM: dts: exynos: Fix port nodes names for Exynos5420 Peach Pit board
ARM: dts: exynos: Fix port nodes names for Exynos5250 Snow board
Signed-off-by: Olof Johansson <olof@lixom.net>
- Update Arria10 ECC manager
- Add ethernet alias for Arria10
- Update serial alias for Arria10
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=WdVs
-----END PGP SIGNATURE-----
Merge tag 'socfpga_updates_v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt
SoCFPGA DTS updates for v4.8
- Update Arria10 ECC manager
- Add ethernet alias for Arria10
- Update serial alias for Arria10
* tag 'socfpga_updates_v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: fix definitions of serial console
ARM: dts: socfpga: add ethernet alias on Arria10
ARM: dts: Move Arria10 SDRAM as child of ECC Manager
ARM: dts: Arria10 ECC Manager IRQ controller changes
Signed-off-by: Olof Johansson <olof@lixom.net>
- Move the ab8500 compatible string from the board to the
chipset.
- Define GPIO line names for the boards.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=sOoX
-----END PGP SIGNATURE-----
Merge tag 'ux500-dt-asoc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt
Ux500 devicetree patches:
- Move the ab8500 compatible string from the board to the
chipset.
- Define GPIO line names for the boards.
* tag 'ux500-dt-asoc-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: dts: UX500: name the GPIO lines on HREFv60plus
ARM: dts: Ux500: name the GPIO lines on Snowball
ARM: dts: Ux500: move compatible string to chipset
Signed-off-by: Olof Johansson <olof@lixom.net>
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7u0/
-----END PGP SIGNATURE-----
Merge tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/dt
Topic branch for adding Exynos 5410 Odroid XU board for v4.8.
This brings support for Hardkernel's Odroid XU board. It was the first
design with big.LITTLE SoC from Samsung: Exynos5410. The board is not
very popular. Newer XU3 and XU4 got more attention.
Board details:
1. Exynos5410 octa-core (A15+A7, however as of now only one cluster is
enabled),
2. 2 GB DDR3 RAM,
3. PowerVR SGX544MP3 GPU (not enabled in DTS),
4. USB 3.0 Host x 1, USB 3.0 OTG x 1, USB 2.0 Host x 4,
5. HDMI 1.4a, MIPI DSI and Display Port (Display Port not on all of
revisions though),
6. eMMC 4.5 and microSD slots.
* tag 'samsung-dt-odroid-xu-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (28 commits)
ARM: dts: exynos: Add watchdog and Security SubSystem to Exynos5410
ARM: dts: exynos: Configure PWM, usb3503, PMIC and thermal on Odroid XU board
ARM: dts: exynos: Add Thermal Management Unit to Exynos5410
ARM: dts: exynos: Interrupt for USB DWC3-1 differs between Exynos5420 and 5410
dt-bindings: clock: Add watchdog and SSS clock IDs to Exynos5410
dt-bindings: clock: Add TMU clock ID to Exynos5410
ARM: dts: exynos: Add RTC and I2C to Exynos5410
ARM: dts: exynos: Add I2C, PWM and UART pinctrl to Exynos5410
ARM: dts: exynos: Move HSI2C nodes to exynos54xx.dtsi
ARM: dts: exynos: Add initial support for Odroid XU board
ARM: dts: exynos: Add USB to Exynos5410
ARM: dts: exynos: Move common Exynos5410/542x/5800 nodes to new DTSI
ARM: dts: exynos: MCT is not an interrupt controller and extend length of iomap
ARM: dts: exynos: Enable UART3 on Exynos5410
ARM: dts: exynos: Include common exynos5 in exynos5410.dtsi
ARM: dts: exynos: Move Exynos5250 and Exynos5420 nodes under soc
ARM: dts: exynos: Use phandle to get parent node in exynos5250-snow
ARM: dts: exynos: Prepare for inclusion of exynos5.dtsi in exynos5410.dtsi
ARM: dts: exynos: Move common nodes to exynos5.dtsi
ARM: dts: exynos: Split Odroid XU3 LEDs to separate DTSI
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Define the port mapping for the SmartRG SR400ACE device.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add interrupt mapping for the Switch Register Access Block. Only 12
interrupts are usable at the moment even though up to 32 are dedicated
to the SRAB.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Add the Switch Register Access Block which is a special piece of
hardware allowing us to perform indirect read/writes towards the
integrated BCM5301X Ethernet switch.
We also add the 4 Gigabit MAC Device Tree nodes within the brcm,bus-axi
bus node to get proper binding between the BCMA instantiated core and
the Device Tree nodes. We will need that to be able to reference
Ethernet Device Tree nodes in a future patch adding the switch ports
layout.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
This patch adds the firmware node for the SCM
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
This patch adds the power key device tree node.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
The #size-cells for the pmics are 0, but we specify a size in the
reg property so that MPP and GPIO modules can figure out how many
pins there are. Now that we've done that by counting irqs, we can
remove the size elements in the reg properties and be DT
compliant.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Enable the sdcard slot and wire up the regulators for the two
storage controllers found on the apq8074 dragonboard.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add the appropriate min/max voltages for the regulators on the
apq8074 dragonboard so that they can be used by clients properly.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add "dis_rxdet_inp3_quirk" boolean property to USB3 node. This property
is used to disable rx detection in P3 PHY mode.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PCI reset GPIO is active low, so represent it with the
GPIO_ACTIVE_LOW flag.
Even though the imx6 PCI driver will not take the polarity into account
in this case, it is better to provide a correct description in device-tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
GPLv2-only devicetrees make reuse difficult for software components
licensed under a different license. In particular, the Utilite Pro
devicetree file (which includes imx6q-cm-fx6.dts) is already dual
licensed under GPLv2/X11.
Hence, relicense imx6q-cm-fx6.dts under GPLv2/X11 dual license.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CompuLab Utilite Pro is a miniature fanless desktop pc based on
the i.MX6 Quad powered cm-fx6 module. It features two serial ports,
USB OTG, 4x USB, analog audio and S/PDIF, 2x Gb Ethernet, HDMI and
DVI ports, an on-board 32GB SSD, a mmc slot, and on-board wifi/bt.
Add initial support for it including USB, Ethernet (both ports), sata
and HDMI support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The cm-fx6 module has an on-board spi-flash chip for its firmware, an
eeprom (containing e.g. the mac address of the on-board Ethernet),
a sata port, a pcie controller, an USB hub, and an USB otg port.
Enable support for them. In addition, enable syscon poweroff support.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The imx6q-cm-fx6 iomuxc container node is not required. Remove it.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
