- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
- Remove useless gpio-cells
- Update second parameter by using GPIO_ACTIVE_HIGH/LOW
instead of hardcoded value
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows to use second parameter to the gpio
specifier, which is used to specify whether the gpio is
active high or low.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
B2260 board is the STMicroelectronics 96Board
based on STiH410 soc :
- 1GB DDR
- On-Board USB combo WiFi/Bluetooth RTL8723BU
with PCB soldered antenna
- Ethernet 1000-BaseT
- Sata
- HDMI
- 2 x USB2 type A
- micro USB2 type AB
- SD card slot
- High speed connector (SD/I2C/USB interfaces)
- Slow speed connector (UART/I2C/GPIO/SPI/PCM interfaces)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Despite ST AHCI version = 1.3, reading HOST_PORTS_IMPL
returns 0. So force HOST_PORTS_IMPL to 1 by using
ports-implemented DT property.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
On 96board, we can't reuse rgmii1-mdio as the pin pio1 3
( mdint ) is dedicated for user led green 1. So create
rgmii1_mdio_1 for 96board on which only mdio and mdc pins
are useful.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Due to 96board which uses mmc0 node for SD card, the non-removable
property must be moved from STiH407-family to board file for B2120
and B2199 boards.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Add missing pin muxing for I2C2 alternate 2. This
i2c2 pin muxing is dedicated for 96board high speed
expansion connector.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Correct spacing between nodes]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
[Lee: Changed node name and added the unit address]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Peter Griffin <peter.griffin@linaro.org>
Introduce the message manager node for the A15 queues on which Linux
runs. The Message Manager is primarily used for communication with
Power Management controller on K2G.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add the DSP GPIO controller node on K2G SoC.
This is used to send interrupts to the only DSP processor
subsystem present on the SoC. The IP is identical to that
of the equivalent nodes on existing K2 SoCs.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add the Keystone IRQ controller IP node on K2G SoC. This allows the
ARM CorePac core to receive interrupts from remote processor devices
(eg: DSP) on the SoC.
The IP is identical in functionality to that of the equivalent
nodes on existing K2 SoCs. The only difference is the ARM INTC
interrupt id/event number.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
Add the device state controller node as a syscon node to the
K2G SoC. This module provides similar device control functionality
as that on the existing K2 SoCs.
One example usage would be the boot address programming of the
DSP processor sub-system.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
The USB OTG mode is not supported by Kestone 2 devices, as result, the
USB devices enumeration and detection will not work properly when
kernel is built with CONFIG_USB_DWC3_DUAL_ROLE=y (default for multi
platform build):
- it's required to load gadget drivers manually to make host mode
work and this confuses current Keystone 2 users
- device mode is not working, because port can't detect and switch to
peripheral/host mode dynamically.
Hence, specify usb mode explicitly in DT: usb0 = "host" for all KS2
devices and usb1 = "peripheral" for K2E.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <ssantosh@kernel.org>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings:
"Node /memory has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it shouldn't have
functional changes.
Since no am4372 based board had a memory node defined, a dummy node
is added so the compiled DTB memory node is the same than before.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
The disassembled DTB are almost the same besides an empty chosen
node being removed and nodes reordered, so it should not have
functional changes.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
But these boards don't have a memory node defined, so removing the
skeleton.dtsi inclusion from omap3.dtsi will cause a change in the
compiled DTB. Add a dummy memory node so the compiled DTB doesn't
change if the skeleton.dtsi is removed from omap3.dtsi.
Eventually the correct starting addresses and sizes should be used
but I didn't find that information.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The skeleton.dtsi file was removed in ARM64 for different reasons as
explained in commit ("3ebee5a2e141 arm64: dts: kill skeleton.dtsi").
These also applies to ARM and it will also allow to get rid of the
following DTC warnings in the future:
"Node /memory has a reg or ranges property, but no unit name"
But the sl50 board doesn't have a, so removing the skeleton.dtsi
inclusion from am33xx.dtsi will cause a change in the compiled DTB.
The board has 512 MiB of RAM and its starting address is 0x80000000,
so add a proper memory device node in the DTS.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Current clocks tree definition for CPSW/CPTS doesn't
correspond TRM for dra7/am57 SoCs.
CPTS: has to be sourced from gmac_rft_clk_mux clock
CPSW: DPLL_GMAC -> CLKOUT_M2 -> GMAC_250M_CLK -> 1/2 ->
-> GMAC_MAIN_CLK (125 MHZ)
Hence, correct clock tree for GMAC_MAIN_CLK and use proper
clock for CPTS. This also require updating of CPTS clock
multiplier.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit fixes the clock data inside the DRA7xx clocks device tree
structure for the gmac_gmii_ref_clk_div clock. This clock is actually
the GMAC_MAIN_CLK and has nothing to do with the register at address
0x4a0093d0. If CLKSEL_REF bit 24 inside of CM_GMAC_GMAC_CLKCTRL, is
set to 1 in order to use the GMAC_RMII_CLK instead of the
GMAC_RMII_HS_CLK, the kernel generates a clock divider warning:
WARNING: CPU: 0 PID: 0 at drivers/clk/clk-divider.c:129 clk_divider_recalc_rate+0xa8/0xe0()
gmac_gmii_ref_clk_div: Zero divisor and CLK_DIVIDER_ALLOW_ZERO not set
By properly configuring the gmac_gmii_ref_clk_div (GMAC_MAIN_CLK) to
have the parent of dpll_gmac_m2_ck always divided by 2 the warning is
resolved and the clock tree is fixed up.
Additionally, a new clock called rmii_50mhz_clk_mux is defined that
does utilize CM_GMAC_GMAC_CLKCTRL[24] CLKSEL_REF to configure the
source clock for the RMII_50MHZ_CLK.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: J.D. Schroeder <jay.schroeder@garmin.com>
Reviewed-by: Trenton Andres <trenton.andres@garmin.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The UniPhier reset controller driver has been merged. Enable it.
Also, replace the fixed-rate clocks with the dedicated clock
drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Since DRA7 has multiple PCIe Rootcomplex, add "linux,pci-domain"
property to assign a PCI domain number to each of the host
bridges.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM335x ICE board has a rotary-switch connected to PCA9536 I2C GPIO
expander. The position of the rotary-switch is reflected by status of
GPIO lines. Add gpio-decoder node to read these GPIO line status via
gpio-decoder driver and report it as an input event to the system.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All UniPhier device trees have the common prefix "uniphier-", so
"ph1-" is just making names longer. Recent documents and other
projects are not using PH1- prefixes any more.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Colibri modules need to be powered using the power pins 3V3 and
AVDD_AUDIO. Add fixed regulators which represent this power rails.
Potentially, those power rails could be switched on a carrier
board. A carrier board device tree could add a own regulator with
a GPIO, and reference that regulator in a vin-supply property of
those new module level system regulators. This also synchronize
the name of the +3.3V regulator with the one used in the Colibri
VF50/VF61 device tree.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Move SD-card definition to module level. While at it, also disable
write-protect since the Colibri standard does not define a pin for
SD-Card write-protection.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add bindings for the Vivante GC400T GPU found in the i.MX6SX.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The SPI controller in the arch/arm/boot/dts/armada-39x.dtsi file has moved
to a different location in the hierarchy, which breaks the overrides
in the board specific file:
Warning (reg_format): "reg" property in /soc/internal-regs/spi@10680/spi-flash@1 has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/internal-regs/spi@10680/spi-flash@1
This changes the board to reference the spi controller by its label
(which has not changed) rather than the full path.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0160a4b689 ("ARM: dts: mvebu: A37x/XP/38x/39x: Move SPI controller nodes into 'soc' node")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
imx6ul-pico has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
At power on, pca953x GPIO pins are configured as input and may cause
unexpected interrupts. Configure the unused pins as GPO low to
avoid unexpected interrupts.
Signed-off-by: Ken Lin <ken.lin@advantech.com.tw>
Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Configure the DWMAC FIFO sizes, burst length and threshold DMA mode on
LPC18xx/43xx SoCs. These parameters are needed for correct operation of
the Ethernet MAC. The DWMAC on LPC18xx/43xx does not support RSF DMA
mode and therefore must use threshold mode.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The 'compatible = "nxp,jc42"' binding only happened to work because
the Linux driver is named jc42. The driver now supports generic
bindings for JC-42 compatible chips, so use the generic binding instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
The inet-d978_rev2 is a pcb used in generic A33 based tablets. It features
volume buttons, micro-usb otg, headphone connector and a power button.
On the board a Realtek RTL8723BS SDIO Wi-Fi module are soldered, and there
is also a accompanied board which has a Goodix GT9271 soldered.
As this board is desired to create tablets with a Home key dealed by
GT9271, a LED is present at the front panel at the position of the
Home key.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R_PIO device node is missing #interrupt-cells, which causes
interrupt parsing to fail to match it as a valid interrupt controller.
Add #interrupt-cells to it. Also remove the unnecesary #address-cells
and #size-cells.
Fixes: 1ac56a6da9 ("ARM: dts: sun9i: Add A80 R_PIO pin controller device
node")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Rename the reference-design-tablet touchscreen node from gsl1680 to
touchscreen, all? tablets seem to use the same power and interrupt
gpio-s, but not all tablets use a gsl1680 controller making the
gsl1680 name somewhat misleading.
Also move the reg and compatible property to the actual tablet dts
as they may differ per tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add a dts file for the Empire Electronix M712 tablet, this is a 7" A13
tablet, with micro-usb (otg), headphone and micro-sd slots on the
outside. It uses a Goodix gt811 touchscreen controller, a RTL8188CTV
wifi chip and a DMART06 (1238a4) accelerometer.
Note currently the dts for this is somewhat empty. This will change
once we add support for the touchscreen and accelerometer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ehci1/ohci1 pair on the ba10-tv-box is connected to an USB-2 wifi
module soldered on the PCB, so there enabling ohci1 is not necessary.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The polaroid-mid2809 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The polaroid-mid2407 tablet has an esp8089 wifi chip,
add a dt node describing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Silicon limitation i845 documents how to cope with false
disconnection condition on USB2 PHY. Reference: AM572x
silicon errata document SPRZ429H, revised January 2016.
Using compatible "ti,dra7x-usb2" enables the recommended
software workaround for this issue. Use it for USB1 PHY.
The workaround is already in place for USB2 PHY.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The wega board has a TLV320AIC3007 connected via McASP0. In the default
configuration, no external crystal is mounted. We run a system clock of
25 MHz, so we use the audio codec PLL for audio clock generation.
Signed-off-by: Stefan Müller-Klieser <s.mueller-klieser@phytec.de>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM572x IDK has a Spansion s25fl256s1 QSPI flash on the EVM connected to
TI QSPI IP over CS0. Hence, add QSPI and flash slave DT nodes.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
According to AM572x DM SPRS953A, QSPI maximum bus speed can be 76.8MHz.
Therefore, increase the spi-max-frequency value of QSPI node to 76.8MHz
for DRA74 and DRA72 evm. This improves flash raw read speed by ~2MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With the device tree parsing using the regulator framework
there is a no longer a need for separate compatibles for
individual regulator nodes. Hence removing them all.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this, the memory will remain active during poweroff consuming
extra power. Please note revision 2.1 PMIC seems to fail when DCDC3
disable is attempted, so this is not done on that PMIC revision. The
PMIC revision checks in the regulator patches make sure of this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Without this, the memory will remain active during poweroff consuming
extra power.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
dcdc3, dcdc5, dcdc6 supply ddr and rtc respectively. These
are required to be on during suspend. Hence set the state accordingly.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add support for the general purpose LEDs on the Blanche board.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add pin control information for the NAND flash interface. This interface
is multiplexed with the device bus interface to the function is "dev"
not "nand" as one might expect.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
By assigning the pin hog to the pinctrl node, we correctly configure the
MPPs. However, they are not available to userspace.
Fix this by assigning the hogs to the gpio node.
After this, the following works as expected:
# echo 28 >/sys/class/gpio/export
# echo low >/sys/class/gpio/gpio28/direction
[gregory.clement@free-electrons.com: fix title]
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
A23/A33 has a NAND controller which can now be used properly.
Add a device node for it.
The DMA function cannot work because of changed DMA IP block, so it's
temporarily removed in the device node. However, with PIO mode it can still
work.
Tested on an Aoson M751s tablet with Boris Brezillon's "mtd: nand: allow
vendor specific detection/initialization" patchset, which is needed for the
large-block MLC chip to be recognized correctly.
( http://lists.infradead.org/pipermail/linux-mtd/2016-June/068198.html )
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Raspberry Pi Zero is a minified version of model A+. It's
notable there is no PWR LED and the ACT LED is inverted.
Additionally the Pi Zero is capable of the USB peripheral mode.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In case dr_mode isn't passed via DT, the dwc2 defaults to OTG mode.
But all Raspberry Pi boards here are designed only for host mode.
So fix this issue by providing a dtsi file which set the dr_mode
to host.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the DWC2 binding an appropriate clock is required.
This clock isn't handled by bcm2835 clock driver, so add a fixed
clock to the bcm283x DT.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables getting a HPD GPIO descriptor quicker.
The exynos-hdmi driver uses "hpd" for HDMI hot plug detection.
static int hdmi_resources_init(struct hdmi_context *hdata)
{
...
hdata->hpd_gpio = devm_gpiod_get(dev, "hpd", GPIOD_IN);
...
}
This calls 'of_find_gpio()' and it generates the GPIO consumer ID by referring
GPIO suffix. So 'hpd-gpios' is preferred on getting a GPIO descriptor.
However, if the device tree uses 'hpd-gpio', then the exynos-hdmi driver
always retries to get a GPIO descriptor because the first GPIO suffix is not
'gpio' but 'gpios'. So you always see the debug message below.
of_get_named_gpiod_flags: can't parse 'hpd-gpios' property of node '/soc/hdmi@14530000[0]'
Use the preferred property, 'hpd-gpios' instead of 'hpd-gpio'.
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
This patch add the IMEM syscon memory region to the DT,
as well as addds support for the magic reboot reason
values that are written to the address for each mode.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Qualcomm SPMI GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
This misconfiguration was caused by a copy/pasting the
APQ8064 set-up, the latter has been fixed in a separate
patch.
Tested with one of the SPMI GPIOs: after this I can
successfully request one of these GPIOs as falling edge
from the device tree.
Fixes: 0840ea9e44 ("ARM: dts: add GPIO and MPP to MSM8660 PMIC")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
The Qualcomm PMIC GPIO and MPP lines are problematic: the
are fetched from the main MFD driver with platform_get_irq()
which means that at this point they will all be assigned the
flags set up for the interrupts in the device tree.
That is problematic since these are flagged as rising edge
and an this point the interrupt descriptor is assigned a
rising edge, while the only thing the GPIO/MPP drivers really
do is issue irq_get_irqchip_state() on the line to read it
out and to provide a .to_irq() helper for *other* IRQ
consumers.
If another device tree node tries to flag the same IRQ
for use as something else than rising edge, the kernel
irqdomain core will protest like this:
type mismatch, failed to map hwirq-NN for <FOO>!
Which is what happens when the device tree defines two
contradictory flags for the same interrupt line.
To work around this and alleviate the problem, assign 0
as flag for the interrupts taken by the PM GPIO and MPP
drivers. This will lead to the flag being unset, and a
second consumer requesting rising, falling, both or level
interrupts will be respected. This is what the qcom-pm*.dtsi
files already do.
Switched to using the symbolic name IRQ_TYPE_NONE so that
we get this more readable.
Cc: stable@vger.kernel.org
Fixes: bce3604696 ("ARM: dts: apq8064: add pm8921 mpp support")
Fixes: 874443fe9e ("ARM: dts: apq8064: Add pm8921 mfd and its gpio node")
Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Björn Andersson <bjorn.andersson@linaro.org>
Cc: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This introduces the gpio-keys node for keys of hammerhead and pinctrl
state associated with it.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-soc@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This DTS file have support LG Nexus 5 (codenamed hammerhead).
Initial version have support for just serial console over headphone
jack.
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: devicetree@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-arm-msm@vger.kernel.org
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
AP148 has a SATA port, but no entity to populate the AHCI
Port Implemented register, so force this in DT.
Signed-off-by: Thomas Pedersen <twp@codeaurora.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
This serial port is used by LG Nexus 5 (codenammed hammerhead).
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: David Brown <david.brown@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: Bhushan Shah <bshah@kde.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Most 8064 devices have micro-usb ports for phy1, so setting
the dr_mode to host here seems incorrect.
Leaving it unspecified should default to otg, and then
any boards that wish to specify something else, can
override it in their dts file.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
In order to have the usb phy work in gadget mode, override
the default host mode with otg mode.
This allows gadget mode to work w/o any hacks to the dtsi file.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Andy Gross <agross@codeaurora.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Stephen Boyd <stephen.boyd@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Signed-off-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Describe 3 instances (VSPS, VSPD0, and VSPD1) of the VSP1V in the R8A7792
device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe the VSP1V clocks in the R8A7792 device tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7511W HDMI transmitter
(connected to DU0) and ADV7123 video DAC (connected to DU1). Add the
necessary subnodes to interconnect DU, HDMI/VDAC devices, and HDMI/VGA
connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Blanche board dependent part of the SDHI0 (connected to the
micro-SD slot) device node along with the necessary voltage regulator.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add a dts file for tablets using the generic inet-q972 PCB.
Tablets with this PCB feature a mini-hdmi output, micro-usb usb-host,
micro-usb usb-otg, 3.5mm headphone jack, a micro sd slot,
(mini) power-barrel and an usb wifi module.
This has been tested on a 9.7" 1024x768 qware qw tb9718-qhd tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Just like with a13/a23/a33 most a31 tablets are derived from the same
reference design. Add a .dtsi file with all the common bits to avoid
endless copy and pasting of these.
The sun6i-reference-design-tablet.dtsi this commit adds is a copy
of sun6i-a31s-colorfly-e708-q1.dts with a few tablet specific bits
removed / left in sun6i-a31s-colorfly-e708-q1.dts.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The presence of the mma8452_int_e708_q1 node is a copy and paste
error, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The 32.768 kHz clock inside the A80 SoC is fed from an external source,
typically the AC100 RTC module.
Make the osc32k placeholder a fixed-factor clock so board dts files can
specify its source.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Almost all sun8i tablets use a gsl1680 touchscreen controller, so add
a node describing it to reference-design-tablet.dtsi.
Almost all, but not all, so mark it as disabled by default (dts files
will also need to supply a firmware-name and resolution info).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The ga10h tablet has a rtl8703as wifi chip, add a dt node describing it.
This enables usage of wifi on this tablet (together with the out of
tree rtl8732bs driver).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This results in quite a nice cleanup for this dts file.
As an added bonus this also enables full otg support. I've tested that
this works as advertised.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Orange Pi Lite SBC is a small H3 based SBC, with 512MB RAM,
micro-sd slot, HDMI out, 2 USB-A connectors, 1 micro-USB connector,
sdio attached rtl8189ftv wifi and an ir receiver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A33-OLinuXino is A33 development board designed by Olimex LTD.
It has AXP223 PMU, 1GB DRAM, a micro SD card, one USB-OTG connector,
headphone and mic jacks, connector for LiPo battery and optional
4GB NAND Flash.
It has two 40-pin headers. One for LCD panel, and one for
additional modules. Also there is CSI/DSI connector.
Signed-off-by: Stefan Mavrodiev <stefan.mavrodiev@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The CHIP has a status LED connected to one of the AXP GPIOs. Add the
gpio-leds node to be able to use the proper LED framework to control it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Add the AXP209 GPIO node to our AXP209 DTSI so that boards can use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Add support for the general purpose software switches SW2 and tactile
switches SW24/25 as a virtual keyboard (like it was done with the Lager/
Koelsch boards).
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The LCDK embeds a TLV320AIC3106 connected to the SoC McASP for analog
audio. The power supply of the codec comes from the main PMIC
(TPS650250) DCDCs which are always on per HW design and not
controllable by SW, so SW wise the codec driver will rely on the 'dummy'
regulator.
Quality is good with arecord -pipe- aplay on Line In/Line Out.
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
The "linux,stdout-path" is deprecated.
Add serial options so the console can be properly configured when
bootloader does not pass "console" parameter to the command line. Without
options and lack of "console" in command line, the serial output dies
during boot (just after probing sound, probably because of rate change).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
There are many regulators are missed in previous commit, this
commit complete most of them. It also fix some mistakes in the
regulator properties. The VDD_10(REG10) and VCC_18(REG11) had better
to keep in always-on state, as it is used as the USB PHY supply,
corretly we have no way to assign power supply to a USB PHY.
The VCCA_33(REG8) should be enabled or the GMAC won't work.
It also fix the wrong properties for audio in io-domains, the supply
connected to APIO4_VDD is different to firefly release version.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Because of a bug in hardware design, the sdcard at firefly
rk3288 reload board can't switch the io voltage level to 1.8v.
Signed-off-by: Randy Li <ayaka@soulik.info>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Currently the davinci da8xx boards use the mach-davinci aemif code.
Instantiating an aemif node into the DT allows to use the ti-aemif
memory driver and is another step to better DT support.
This change adds an aemif node in the dtsi while retiring the nand_cs3
node. The NAND is now instantiated in the dts as a subnode of the aemif
one along with its pins.
Signed-off-by: Karl Beldan <kbeldan@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
imx7s-warpd has WDOG1_B pin connected to the PMIC.
Pass the 'fsl,ext-reset-output' property so that the watchdog
can trigger a system POR reset via the PMIC.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Warp7 has a BCM43430 Wifi chip connected to the USDHC1 port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
warp7 has a sgtl5000 audio codec.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Only i.MX 7Dual SoC supports CPU frequencies of up to 1GHz. The i.MX
7Solo can run with up to 800MHz and does so without making use of DVFS
usually. While the device tree clearly specified a too fast operating
point for i.MX 7Solo, the kernel did not used it in practise so far
because the CPUfreq driver does not get loaded on i.MX 7Solo devices
(since the fsl,imx7s compatible string is not in the list of devices
making use of the cpufreq-dt driver...).
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
As of commit 5aa2eb3c86 ("[media] v4l: vsp1: Configure device
based on IP version"), the DT properties to identify the exact VSP
device instance features are no longer used. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
As of commit 5aa2eb3c86 ("[media] v4l: vsp1: Configure device
based on IP version"), the DT properties to identify the exact VSP
device instance features are no longer used. Hence remove them.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Alt board dependent part of the MMCIF device node.
Like the Silk the board has eMMC chip along with the necessary voltage
regulator (note that the Vcc/Vccq regulator is dummy -- it's required by
the MMCIF driver but doesn't actually exist on the board).
Based on work for the Silk board by Vladimir Barinov and Sergei Shtylyov.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Define the Alt board dependent part of the SDHI0 and 1
device nodes along with the necessary voltage regulators.
Based on work by the original patch by Vladimir Barinov and
Sergei Shtylyov for the Silk board.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Describe two instances (VSPS and VSPD0) of the VSP1 in the R8A7794 device
tree.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The ARM GIC only supports interrupts with either level-high or
rising-edge types for SPIs. The interrupt type for the Palmas PMIC used
for Tegra114 boards is specified as level-low which is invalid for the
GIC. This has gone undetected because until recently, failures to set
the interrupt type when the interrupts are mapped via firmware (such as
device-tree) have not been reported. Since commits 4b357daed6
("genirq: Look-up trigger type if not specified by caller") and
1e2a7d7849 ("irqdomain: Don't set type when mapping an IRQ"), failure
to set the interrupt type will cause the requesting of the interrupt to
fail and exposing incorrectly configured interrupts.
Please note that although the interrupt type was never being set for the
Palmas PMIC, it was still working fine, because the default type setting
for the interrupt, 'level-high', happen to match the correct type for
the interrupt.
Finally, it should be noted that the Palmas interrupt from the PMIC is
actually 'level-low', however, this interrupt signal is inverted by the
Tegra PMC and so the GIC actually sees a 'level-high' interrupt which is
what should be specified in the device-tree interrupt specifier.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
DT compatible values should always include an entry for the specific
chip in addition to any earlier generations that the HW is backwards-
compatible with.
This doesn't affect the kernel at all given current driver code, but
U-Boot needs to distinguish between Tegra114 and Tegra30 for this HW,
and I'd like to synchronize the DT content.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /leds/led@1 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /gpio_keys/button0@10 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /fixedregulator@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /matrix_keypad@0 has a unit name, but no reg property"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit b8d368caa8 ("ARM: dts: omap3: overo: remove unneded unit names
in display nodes") removed the unit names for all Overo display nodes
that didn't have a reg property.
But the display in arch/arm/boot/dts/omap3-overo-common-lcd35.dtsi does
have a reg property so the correct fix was to make the unit name match
the value of the reg property, instead of removing it.
This patch fixes the following DTC warning for boards using this dtsi:
"ocp/spi@48098000/display has a reg or ranges property, but no unit name"
Fixes: b8d368caa8 ("ARM: dts: omap3: overo: remove unneded unit names in display nodes")
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following DTC warnings for many boards:
"Node /ocp has a reg or ranges property, but no unit name"
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fix was applied to a bunch of omap3 devices including LogicPD
Torpedo, but this got missed since it was new around the same times
the patches were applied. This makes the GPMC parameters match the
Torpedo since they have the same processor PoP memory.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This was applied to a variety of omap3 boards, so it should
probably be applied here. I did not test NAND performance, but
I tested this with UBI to confirm read/write didn't break.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpmc ranges property for NAND at CS0 was being overridden by later
includes that defined gpmc ethernet nodes, effectively breaking NAND on
these systems:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
Instead of redefining the NAND range in every such dtsi, define all
currently used ranges in omap3-overo-base.dtsi.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The gpmc ranges property for NAND at CS0 has been broken since it was
first added.
This currently prevents the nand gpmc child node from being probed:
omap-gpmc 6e000000.gpmc: /ocp/gpmc@6e000000/nand@0,0 has
malformed 'reg' property
and consequently the NAND device from being registered.
Fixes: 98ce6007ef ("ARM: dts: overo: Support PoP NAND")
Cc: stable <stable@vger.kernel.org> # 4.3
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
