[WHY]
Due to pass the wrong parameter down to the enable_stream_gating(),
it would cause the DSC of the removing stream would not be PG.
[HOW]
To pass the correct parameter down th the enable_stream_gating().
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.
[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
1. The code to blank all dp display have been called many times,
so add helpers in dc_link to make it more concise.
2. Add some check to fix the dmesg errors at boot and resume from S3
on dcn3.1 during DQE's promotion test.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPO is only used for DP2.0. HPO HW control should be
disable when not being used to save power.
[How]
Shutdown HPO HW control during init hw.
Shutdown HPO HW control during stream disable.
Enable HPO HW control during stream enable if DP2.0.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
i2c memory doesn't get set to light sleep on hw init as intended
[HOW]
Set i2c to light sleep after reg gets zeroed, ensuring memory power
control doesn't get disabled for any other DIO memory
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 1445d967fb.
This patch introduced a couple of dmesg warnings, this is not a valid
approach anymore. For this reason, we are reverting this patch, and we
need to revert the workaround patch.
v2: squash in unused variable removal (Alex)
Cc: Hanghong Ma <hanghong.ma@amd.com>
Cc: Mark Broadworth <mark.broadworth@amd.com>
Signed-off-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Immediate flip can be enabled dynamically and has higher BW requirements
when validating which voltage mode to use.
If we validate when it's not set then potentially DCFCLK will be too low
and we will underflow.
[How]
DM always requires support so always require it as part of DML input
parameters.
This can't be enabled unconditionally on older ASIC because it blocks
some expected modes so only target DCN3.1 for now.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Hardware team has recommended to generically hard code this register to
0xFF as part of the effort to eventually remove this control. However
we set it to 0xF instead.
This causes 4 of audio 8ch to be muted.
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIB_BE_CNTL<i>.DIG_HPD_SELECT selects the HPD block being used
by the display endpoint assigned to DIG<i>. In the case of USB4
display endpoints, no physical HPD block is assigned.
[How]
Setting DIB_BE_CNTL<i>.DIG_HPD_SELECT to 5 indicates that no HPD
is assigned to a display endpoint. Firmware decrements the
HPD_SELECT value by 1 before writing it to the register.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Training settings need to be applied to DPIA link at start of each
training loop. Note: FEC readiness should be configured before link
training while FEC enablement should be configured once training is
complete.
[How]
- Implement DPIA link configuration function.
- Account for dynamically assigned link encoders during link
configuration.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
To enable dc links for USB4 DPIA ports and AUX command tunneling
for YELLOW_CARP_B0.
[HOW]
1) Created dc links for all USB4 DPIA ports in create_links().
dc_link_construct() implementation is split for legacy DDC and DPIAs.
As usb4 has no ddc, ddc->ddc_pin will be set to NULL for its dc link
and this parameter will be used to identify the dc links as DPIA. The
dc link for DPIA is further to be enhanced with implementation for link
encoder and link initialization.
2) usb4_dpia_count in struct resource_pool will be initialized to 4 in
dcn31_resource_construct() if the DCN is YELLOW_CARP_B0.
3) Enabled DMUB AUX via outbox for YELLOW_CARP_B0.
Reviewed-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Acked-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The codes to blank all dp display have been called many times,
so add a helper in dc_link to make it more concise.
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Starting from B0, along with RDPCSTX, RDPCSPIPE registers are also used.
[How]
Make sure RDPCSPIPE registers are programmed correctly.
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Why:
Screen sometimes would have artifacts or blink once at the time when bpp
is dynamically changed.
How:
1. Changed to update PPS infopacket in frame mode instead of immediate mode
since other updates for bpp change are double-buffered.
2. Changed double-buffering enablement programming for DCN30 as advised by
ASIC team
Reviewed-by: Wenjing Liu <wenjing.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bing Guo <Bing.Guo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The change of setting a timer callback on boot for 10 seconds is still
working, just lost power down on boot and power down for DCN3.
[How]
Added power down on boot and power down for DCN3.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Derek Lai <Derek.Lai@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Incorrect encoder assignments were being used while applying a new state
to hardware.
(1) When committing a new state to hardware requires resetting the
back-end, the encoder assignments of the current or old state should be
used when disabling the back-end; and the encoder assignments for the
next or new state should be used when re-enabling the back-end.
(2) Link training on hot plug could take over an encoder already in use
by another stream without first disabling it.
[How]
(1) Introduce a resource context 'link_enc_cfg_context' which includes:
- a mode to indicate when transitioning from current to next state.
- transient encoder assignments to use during this state transition.
Update the encoder configuration interface to respond to queries about
encoder assignment based on the mode of operation.
(2) Check if an encoder is already in use before attempting to perform
link training on hot plug.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
